BIS - LIMS (Laboratory Information Management System)

Ace Test Labs & Metrology Pvt. Ltd., Sonipat

PLOT NO. 68, HSIIDC, INDUSTRIAL ESTATE,RAI, SONIPAT, Sonipat, Haryana, 131029

8816921177 info@acetestgroup.com

Scope List

Reset

96 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 8148 (2018)

Ducted and package air - Conditioners - Specification (Second Revision)

665000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 &4.5(Salt Spray Test)	-	40000	-
7.1 , 7.2 & 8.1(Capacity Rating Test & ISEER Test Condition )	-	140000	-
7.3 & 8.3(Maximum Cooling Conditions Test)	-	60000	-
7.4 & 8.4, 8.5(Freeze-Up Test)	-	30000	-
7.5 & 8.6(Enclosure Sweat Test)	-	20000	-
7.6 & 8.7(Condensate Desposal Test)	-	30000	-
8.8(Power Consumption Test)	-	25000	-
9.1(Heating Capacity Test)	-	100000	-
9.2(Maximum Heating Performance Test)	-	50000	-
9.3(Automatic Defrost Performance Test)	-	40000	-
11(Sound Test)	-	40000	-
12.2.1( Running Test)	-	25000	-
12.2.2(Pressure Test or Leakage Test)	-	50000	-
12.2.3(Insulation Resistance Test)	-	10000	-
12.2.4(High Voltage Test)	-	10000	-
12.2.5(Leakage Current Test)	-	10000	-
12.2.6(Provisions for Earthing (Earth Resistance Test))	-	10000	-
12.3.3(Safety Tests: )	-	50000	-
13.1(Marking)	-	5000	-
13.2(BIS Certification Marking)	-	5000	-
7.3 & 8.3(Maximum Cooling Conditions Test)	-	60000	-
7.3 & 8.3(Maximum Cooling Conditions Test)	-	60000	-
7.3 & 8.3(Maximum Cooling Conditions Test)	-	60000	-
4.2 &4.5(Salt Spray Test)	-	40000	-
4.2 &4.5(Salt Spray Test)	-	40000	-
13.2(BIS Certification Marking)	-	5000	-
13.2(BIS Certification Marking)	-	5000	-

14 Nov, 2027

-
-

IS 17681 (2022)

Specification for Bottled water dispensers

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Construction)	-	5000	-
4.1(General Design)	-	500	-
4.2(Materials)	-	500	-
4.3(Finish)	-	500	-
4.4(Thermal Insulation)	-	500	-
4.5(Hardware)	-	500	-
4.6(Disposal of Waste Water)	-	500	-
4.7(Hot Water Tank)	-	500	-
4.8(Hermetically Sealed Compressor)	-	500	-
4.9(Protective Guards)	-	500	-
5(Refrigeration System)	-	5000	-
5.1(Pipes and Connections/Fitting)	-	500	-
5.2(Control of Operation)	-	500	-
6.1(General)	-	1500	-
6.1(Protection against electric shock (Cl. 8 of IS 302-2-24))	-	3500	-
6.1(Power Input & Current (Cl. 10 of IS 302-2-24))	-	5000	-
6.1(Temperature Rise/ Heating (Cl. 11 of IS 302-2-24))	-	6000	-
6.1("Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength (Cl. 13 of IS 302-2-24)")	-	3500	-
6.1("Moisture Resistance (Cl. 15 of IS 302-2-24)")	-	4000	-
6.1("Insulation resistance and electric strength (After humidity treatment) (Cl. 16 of IS 302-2-24)")	-	3500	-
6.1("Provision For Earthing (Cl. 27 of IS 302-2-24)")	-	4000	-
6.1("Screws & Connections (Cl. 28 of IS 302-2-24)")	-	3000	-
6.2(Electrical Accessories)	-	1500	-
6.3(Salt Mist Test)	-	30000	-
7(Sound pressure level)	-	15000	-
10.1(Cooling Capacity Test)	-	22000	-
10.2(Maximum Operating Condition Test (Environmental))	-	15000	-
10.3(Maximum Operating Condition Test (Voltage))	-	18000	-
10.4(Heating Capacity Test)	-	18000	-
10.5(Annual Energy Consumption Test)	-	35000	-
10.6(Freeze-up Test)	-	20000	-
10.7(Door Opening and Closing Test)	-	8000	-
10.8(Door Seal Test)	-	2000	-
10.9(Pull-down Test)	-	12000	-
11(Marking and instruction)	-	1000	-

14 Nov, 2027

-
-

IS 3315 (2024)

Direct Evaporative Air Cooler â Specification (Fourth Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Enclosure)	-	5000	-
Cl-5.2(Filter Pads)	-	5000	-
Cl-5.3(Sump Tank Capacities)	-	5000	-
Cl-5.4(Blower/Fan)	-	15000	-
Cl-5.4.3(Fan motor)	-	15000	-
Cl-5.5(Pump Set)	-	35000	-
Cl-5.6.1(Electrical wiring and connection)	-	5000	-
Cl-5.6.2(Suitable power cable)	-	5000	-
Cl-5.7(Switches)	-	5000	-
Cl-6(Rating Requirement)	-	5000	-
Cl-8.1(Performance Requirement)	-	25000	-
Cl-8.2(Sound Test)	-	25000	-
Cl-8.3(Air Delivery (Air Flow) Test)	-	25000	-
Cl-8.4(Cooling Efficiency Test)	-	45000	-
Cl-8.5(Power Consumption)	-	20000	-
Cl-8.6(EER Calculation Method)	-	45000	-
Cl-8.7(Drop Test)	-	15000	-
Cl-8.8(Air Cooler Blower/Fan Reliability Test)	-	15000	-
Cl-12.2.1(General Running Tests)	-	25000	-
Cl-12.2.2(Protection against Electric Shock)	-	15000	-
Cl-12.2.3(High Voltage Tests)	-	10000	-
Cl-12.2.4(Leakage Current)	-	15000	-
Cl-12.2.5(Provision for Earthing)	-	12000	-
Cl-12.2.6(Finish)	-	12000	-
Cl-13(Additional Requirement for ECO-Mark)	-	5000	-
Cl-14(Storage)	-	18000	-

14 Nov, 2027

-
-

IS 2993 : Part 1 (2024)

a.c. Motor Capacitors Part 1 General - Performance, Testing and Rating - Safety Requirements - Guidance for Installation and Operation ( Third Revision )

375000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(General)	-	4000	-
5.5(Tangent of loss angle)	-	18000	-
5.7("Voltage test between terminals ")	-	9000	-
5.8(Voltage test between terminals and case)	-	9000	-
5.9(Capacitance measurement)	-	13500	-
5.9(Capacitance measurement)	-	100000	-
5.1(Check of dimensions)	-	4000	-
5.11(Mechanical tests)	-	62500	-
5.12(Sealing test)	-	10000	-
5.13(Endurance test)	-	201500	-
5.14(Damp heat test)	-	76000	-
5.15(Self-healing test)	-	10000	-
5.16(Destruction test)	-	42000	-
5.17(Resistance to heat, fire and tracking)	-	10000	-
5.17.1(Ball-pressure test)	-	5000	-
5.17.2(Glow-wire test)	-	5000	-
5.17.3(Tracking test)	-	10000	-
6.1(Maximum permissible voltage)	-	5000	-
6.2("Maximum permissible current ")	-	5000	-
6.3(Maximum permissible reactive output)	-	5000	-
7(Safety requirements)	-	4000	-
7.1(Requirements for Creepage distances and clearances)	-	4000	-
7.2(Terminals and connecting cables)	-	4000	-
7.3(Earth connections)	-	4000	-
7.4(Discharge devices)	-	4000	-
8(Marking)	-	2000	-
9.2.1(Measurements of working voltage)	-	10000	-
9.2.2(Influence of capacitance)	-	20000	-
9.3(Checking capacitor temperature)	-	25000	-
9.4(Checking transients)	-	25000	-
9.5(Leakage current)	-	10000	-

14 Nov, 2027

-
-

IS 17550 : PART 1 (2021)

HOUSEHOLD REFRIGERATING APPLIANCES CHARACTERISTICS AND TEST METHODS Part 1 General Requirements

200000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
"Cl. No. 9 "(Testing The Air Tightness Of Door Or Lid Seal(S))	-	3000	-
"Cl. No.10 "(Testing The Opening Force Of Door(S) Or Lid(S))	-	10000	-
"Cl. No.11 "(Testing The Durability Of Hinges And Handles Of Door(S) And Lid(S))	-	50000	-
"Cl. No.12 "(Testing The Mechanical Strength Of Shelves And Similar Components)	-	10000	-
"Cl. No.14 "(Ice-Making Test (If Applicable))	-	30000	-
"Cl. No.15 "(Test For Absence Of Odour And Taste)	-	50000	-
"Cl. No.16 "(Safety Requirements)	-	50000	-
"Cl. No. 9 "(Testing The Air Tightness Of Door Or Lid Seal(S))	-	3000	-
"Cl. No.10 "(Testing The Opening Force Of Door(S) Or Lid(S))	-	10000	-
"Cl. No.11 "(Testing The Durability Of Hinges And Handles Of Door(S) And Lid(S))	-	50000	-
"Cl. No.12 "(Testing The Mechanical Strength Of Shelves And Similar Components)	-	10000	-
"Cl. No.14 "(Ice-Making Test (If Applicable))	-	30000	-
"Cl. No.15 "(Test For Absence Of Odour And Taste)	-	50000	-
"Cl. No.16(a) "(Protection against acess to live parts)	-	5000	-
"Cl. No.16(b) "(Power input and current)	-	10000	-
"Cl. No.16(c) "(Heating)	-	15000	-
"Cl. No.16(d) "(Leakage current and electric strength at operating temperature)	-	5000	-
"Cl. No.16(e) "(Moisture resistance)	-	10000	-
"Cl. No.16(f) "(Leakage current and electric strength)	-	10000	-
"Cl. No.20.3(a) "("Production Routine Test a)Leakage current test ")	-	5000	-
"Cl. No.20.3(b) "(b) Earth continuity tesT)	-	5000	-
"Cl. No.20.3(c) "(c) Electric strength)	-	5000	-
"Cl. No.8.11 "(Thermostat function test)	-	2500	-
"Cl. No.5 "(Markings)	-	2500	-
4(Classification)	-	500	-
5(Marking)	-	2500	-
6.2(Determination of Linear Dimensions)	-	1000	-
7(Instructions)	-	500	-
8.2(Material and Finishes)	-	500	-
8.3(Thermal Insulation and Air Tightness)	-	500	-
8.4(Doors, Lids and Fittings)	-	500	-
8.5(Shelves and Containers)	-	500	-
8.6(Disposal of Defrost Water)	-	500	-
8.7(Refrigerating System)	-	500	-
8.8(Supply Cord)	-	5000	-
8.9(Compressor)	-	150000	-
8.10(Temperature Sensing Controls (Thermostat))	-	5000	-
8.11(Temperature Sensing Controls (Thermostat) Setting)	-	2500	-
9(Testing the Air tightness of door or lid seal(s) before water vapour condensation test)	-	3000	-
9(Testing the Air tightness of door or lid seal(s) after water vapour condensation test)	-	3000	-
10(Testing the Opening force of door(s) or lid(s))	-	10000	-
11(Testing the Durability of hinges and handles of door(s) and lid(s))	-	50000	-
12(Testing the Mechanical strength of shelves and similar components)	-	10000	-
13(Water-vapour condensation test)	-	30000	-
14(Ice-making test (if applicable))	-	30000	-
15(Test for absence of odour and taste)	-	50000	-
16(a)(Protection against access to live parts)	-	5000	-
16(b)(Power input and current)	-	10000	-
16 (c(Heating)	-	15000	-
16(d)(Leakage current and electric strength at operating temperature)	-	5000	-
16(e)(Moisture resistance)	-	10000	-
16(f)(Leakage current and electric strength (high voltage after humidity))	-	10000	-
17(Packing)	-	5000	-
18(Designation)	-	5000	-
19(Instructions for Use and Maintenance)	-	5000	-
20.3 (a)(Leakage Current Test)	-	5000	-
20.3 (b)(Earth Continuity Test)	-	5000	-
20.3 (c(Electric Strength Test)	-	5000	-

14 Nov, 2027

-
-

IS 302 : Part 2 : Sec 13 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 13 Deep Fat Fryers, Frying Pans and Similar Appliances (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	1500	-
8(Protection against access to live parts)	-	1500	-
10(Power input and current)	-	5000	-
11(Heating)	-	5000	-
13.1 &13.2(Leakage current test)	-	5000	-
13.1 &13.3(Electric strength test)	-	5000	-
14(Transient overvoltages)	-	5000	-
15(Moisture resistance)	-	5000	-
15.3(Moisture resistance)	-	5000	-
15.101(Moisture resistance)	-	5000	-
16.1 &16.2(Leakage current test)	-	5000	-
16.1 & 16.3(Electric strength test)	-	5000	-
17(Overload protection of transformers and associated circuits)	-	5000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	5000	-
19.101 to to 19.102(Abnormal operation)	-	5000	-
20(Stability and mechanical hazards)	-	5000	-
21(Mechanical strength)	-	5000	-
22(Construction)	-	5000	-
22.101(Construction)	-	5000	-
23(Internal wiring)	-	5000	-
24(Components)	-	5000	-
25("Supply connection and external flexible cords")	-	5000	-
26("Terminals for external conductors")	-	5000	-
27(Provision for earthing)	-	5000	-
28(Screws and connections)	-	5000	-
29("Clearances, creepage distances and solid insulation")	-	5000	-
30(Resistance to heat and fire)	-	5000	-
31(Resistance to rusting)	-	5000	-
32("Radiation, toxicity and similar hazards")	-	5000	-

14 Nov, 2027

-
-

IS 13340 : PART 1 (2024)

Shunt Power Capacitors of the Self-Healing Type for a.c. Systems Having a Rated Voltage up to and Including 1 000 V Part 1 General - Performance, Testing and Rating - Safety Requirements - Guide for Installation and Operation (Second Revision)

242000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Capacitance measurement and output calculation)	-	24000	-
8(Measurement of the tangent of the loss angle (tan δ) of the capacitor)	-	11000	-
9(Voltage tests between terminals)	-	3000	-
10(Voltage tests between terminals and container)	-	3000	-
11(Voltage tests between terminals and container)	-	5500	-
12(Sealing test)	-	11000	-
13(Thermal stability test)	-	24000	-
14("Measurement of the tangent of the loss angle (tan δ) of the capacitor at elevated temperature")	-	24000	-
7(Capacitance measurement and output calculation)	-	10000	-
15(Lightning impulse voltage test between terminals and container)	-	10000	-
16(Discharge test)	-	12000	-
17(Ageing test)	-	51500	-
18(Self-healing test)	-	11000	-
19(Destruction test)	-	31000	-
20(Maximum permissible voltage)	-	8000	-
20.1(Long-duration voltages)	-	10000	-
20.2(Long-duration voltages)	-	10000	-
21(Maximum permissible current)	-	8000	-
22(Discharge device)	-	5500	-
23("Container connections ")	-	5000	-
24(Protection of the environment)	-	5000	-
25(Other safety requirements)	-	5000	-
26(Marking of the unit)	-	1500	-
26.1(Rating plate)	-	0	-
26.2(Standardized connection symbols)	-	0	-
26.3(Warning plate)	-	0	-
27(Marking of the bank)	-	0	-
27.1(Instruction sheet or rating plate)	-	0	-
27.2(Warning plate)	-	0	-
28(General)	-	0	-
29(9 Choice of the rated voltage)	-	0	-
30(Operating temperature)	-	0	-
31(Special service conditions)	-	0	-
32(2 Overvoltages)	-	0	-
33(Overload currents)	-	0	-
34(Switching and protective devices and connections)	-	0	-
36(Capacitors connected to systems with audio-frequency remote control)	-	0	-
36(Capacitors connected to systems with audio-frequency remote control)	-	0	-

14 Nov, 2027

-
-

IS 17636 (2021)

Bunk Beds - Specification

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(DESIGN AND WORKMANSHIP)	-	5000	-
CLAUSE 5(DIMENSIONS)	-	5000	-
CLAUSE 6(SURFACE PERFORMANCE)	-	5000	-
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	5000	-
CLAUSE 7.5.1(Attachment, Deflection and Strength of Ladder and Treads)	-	5000	-
CLAUSE 7.6(Strength of Frame and Fastenings)	-	5000	-
CLAUSE 7.7(Stability Test)	-	5000	-
CLAUSE 7.8(Fastening of Upper Bed to Lower Bed)	-	5000	-
Cl-5(Dimensions)	-	5000	-
Cl-6.1 (a)(Resistance to mechanical damage)	-	5000	-
Cl-6.1 (b)(Pencil hardness)	-	5000	-
Cl-6.1 (c)(Resistance to wet heat)	-	5000	-
Cl-6.1 (d)(Resistance to dry heat)	-	5000	-
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	5000	-
Cl-6.1 (f)(Resistance to marking by cold oils and fats)	-	5000	-
Cl-6.1 (g)(Adhesive performance)	-	5000	-
Cl-6.2 (a) 1(Breaking load)	-	5000	-
Cl-6.2 (a) 2(Elongation at break)	-	5000	-
Cl-6.2 (a) 3(Tear strength)	-	5000	-
Cl-6.2 (a) 4(Colour fastness to light)	-	5000	-
Cl-6.2 (a) 5(Colour fastness to rubbing)	-	5000	-
Cl-6.2 (a) 6(Colour fastness to perspiration)	-	5000	-
Cl-6.2 (a) 7(Colour fastness to water)	-	5000	-
Cl-6.2 (a) 8(Pilling resistance)	-	5000	-
Cl-6.2 (a) 9(Coating adhesion strength)	-	5000	-
Cl-6.2 (a) 10(Seam slippage)	-	5000	-
Cl-6.2 (a) 11(Resistance to damage by flexing)	-	5000	-
Cl-6.2 (a) 12(Abrasion resistance)	-	5000	-
Cl-6.2 (a) 13(Bursting strength)	-	5000	-
Cl-6.2 (a) 14(Resistance to cold)	-	5000	-
Cl-6.2 (b) 1(Tear strength)	-	5000	-
Cl-6.2 (b) 2(Flexing endurance)	-	5000	-
Cl-6.2 (b) 3(Finish adhesion)	-	5000	-
Cl-6.2 (b) 4(Colour fastness to artificial light)	-	5000	-
Cl-6.2 (b) 5(Colour fastness to rubbing)	-	5000	-
Cl-6.2 (b) 6(Colour fastness to water spotting)	-	5000	-
Cl-6.2 (b) 7(Water vapour permeability)	-	5000	-
Cl-6.2 (b) 8(Colour fastness to water)	-	5000	-
Cl-7.1(general test conditions)	-	5000	-
Cl-7.2.1(Top Bed Safety Barriers)	-	5000	-
Cl-7.2.2(Top Bed Safety Barriers)	-	5000	-
Cl-7.2.3(Top Bed Safety Barriers)	-	5000	-
Cl-7.2.4(Top Bed Safety Barriers)	-	5000	-
Cl-7.3.1(Gaps)	-	5000	-
Cl-7.3.2(Gaps)	-	5000	-
Cl-7.4.1(Bed Base)	-	5000	-
Cl-7.4.2(Bed Base)	-	5000	-
Cl-7.5.1(Attachment, Deflection and Strength of Ladder and Treads)	-	5000	-
Cl-7.5.2(Dimensions of Treads)	-	5000	-
Cl-7.6(Strength of Frame and Fastenings)	-	5000	-
Cl-7.7(Stability)	-	5000	-
Cl-7.8(Fastening of Upper Bed to Lower Bed)	-	5000	-
Cl-10(Marking)	-	5000	-

14 Nov, 2027

-
-

IS 17635 (2022)

Beds - Specification

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(Design and workmanship)	-	5000	-
CLAUSE 5(Dimensions)	-	5000	-
CLAUSE 6(SURFACE PERFORMANCE)	-	5000	-
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	5000	-
CLAUSE 7(SAFETY TESTS)	-	5000	-
CLAUSE 7.3(Stability Test)	-	5000	-
CLAUSE 7.4(Vertical Static Load Tests)	-	5000	-
CLAUSE 7.5(Horizontal Static Load Tests)	-	5000	-
CLAUSE 7.5.2(Horizontal Static Load Test of Beds Without Headboard)	-	5000	-
CLAUSE 7.6.1(Vertical Durability Test of Bed Base)	-	5000	-
CLAUSE 7.6.2(Horizontal Durability Test of Bed Frame)	-	5000	-
CLAUSE 7.6.3(Horizontal Durability Test of Headboards)	-	5000	-
CLAUSE 7.7(Vertical Impact Test)	-	5000	-
CLAUSE 8.1(Mechanisms for Lifting Bed Bases)	-	5000	-
CLAUSE 8.2(Extendable Storage Elements)	-	5000	-
Cl-5(Dimensions)	-	5000	-
Cl-6.1 (a)(Resistance to mechanical damage)	-	5000	-
Cl-6.1 (b)(Pencil hardness)	-	5000	-
Cl-6.1 (c)(Resistance to wet heat)	-	5000	-
Cl-6.1 (d)(Resistance to dry heat)	-	5000	-
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	5000	-
Cl-6.1 (f)(Resistance to marking by cold oils and fats)	-	5000	-
Cl-6.1 (g)(Adhesive performance)	-	5000	-
Cl-6.2 (a) 1(Breaking load)	-	5000	-
Cl-6.2 (a) 2(Elongation at break)	-	5000	-
Cl-6.2 (a) 3(Tear strength)	-	5000	-
Cl-6.2 (a) 4(Colour fastness to light)	-	5000	-
Cl-6.2 (a) 5(Colour fastness to rubbing)	-	5000	-
Cl-6.2 (a) 6(Colour fastness to perspiration)	-	5000	-
Cl-6.2 (a) 7(Colour fastness to water)	-	5000	-
Cl-6.2 (a) 8(Pilling resistance)	-	5000	-
Cl-6.2 (a) 9(Coating adhesion strength)	-	5000	-
Cl-6.2 (a) 10(Seam slippage)	-	5000	-
Cl-6.2 (a) 11(Resistance to damage by flexing)	-	5000	-
Cl-6.2 (a) 12(Abrasion resistance)	-	5000	-
Cl-6.2 (a) 13(Bursting strength)	-	5000	-
Cl-6.2 (a) 14(Resistance to cold)	-	5000	-
Cl-6.2 (b) 1(Tear strength)	-	5000	-
Cl-6.2 (b) 2(Flexing endurance)	-	5000	-
Cl-6.2 (b) 3(Finish adhesion)	-	5000	-
Cl-6.2 (b) 4(Colour fastness to artificial light)	-	5000	-
Cl-6.2 (b) 5(Colour fastness to rubbing)	-	5000	-
Cl-6.2 (b) 6(Colour fastness to water spotting)	-	5000	-
Cl-6.2 (b) 7(Water vapour permeability)	-	5000	-
Cl-6.2 (b) 8(Colour fastness to water)	-	5000	-
Cl-7.1(Safety Tests)	-	5000	-
Cl-7.2(Safety Tests)	-	5000	-
Cl-7.3(Stability Test)	-	5000	-
Cl-7.4.1(Vertical Static Load on Bed Base)	-	5000	-
Cl-7.4.2(Vertical Static Load on Side Rail)	-	5000	-
Cl-7.5.1(Horizontal Static Load on Headboard)	-	5000	-
Cl-7.5.2(Horizontal Static Load Test of Beds Without Headboard)	-	5000	-
Cl-7.6.1(Vertical Durability Test of Bed Base)	-	5000	-
Cl-7.6.2(Horizontal Durability Test of Bed Frame)	-	5000	-
Cl-7.6.3(Horizontal Durability Test of Headboards)	-	5000	-
Cl-7.7(Vertical Impact Test)	-	5000	-
Cl-8.1.2(Durability of Mechanisms for Lifting Bed Bases)	-	5000	-
Cl-8.2.2(Durability of Extendable Storage Elements)	-	5000	-
Cl-10(Marking)	-	5000	-

14 Nov, 2027

-
-

IS 17634 (2022)

Storage Units - Specification

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 5(DIMENSIONS)	-	5000	-
CLAUSE 6(SURFACE PERFORMANCE)	-	5000	-
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	5000	-
CLAUSE 7.1(SAFETY TESTS (General))	-	5000	-
CLAUSE 7.2(Test for Non-Movable Parts)	-	5000	-
CLAUSE 7.2.1(Shelves)	-	5000	-
CLAUSE 7.2.1.2(Deflection of shelves)	-	5000	-
CLAUSE 7.2.2.1(Sustained load test for tops and bottoms)	-	5000	-
CLAUSE 7.2.2.2(Static load test for tops and bottoms)	-	5000	-
CLAUSE 7.2.3.1(Strength of clothes-rail supports)	-	5000	-
CLAUSE 7.2.3.2(Dislodgement of clothes rail)	-	5000	-
CLAUSE 7.2.4.2(Drop test)	-	5000	-
CLAUSE 7.2.4.3(Tests for units with castors or wheels)	-	5000	-
CLAUSE 7.3.1(Pivoted Doors)	-	5000	-
CLAUSE 7.3.1.2.1(Vertical load on pivoted door)	-	5000	-
CLAUSE 7.3.1.2.2(Horizontal load on pivoted door)	-	5000	-
CLAUSE 7.3.1.3(Slam-shut test of pivoted doors)	-	5000	-
CLAUSE 7.3.1.4(Durability of pivoted doors)	-	5000	-
CLAUSE 7.3.2(Sliding Doors and Horizontal Roll-fronts)	-	5000	-
CLAUSE 7.3.2.2(Slam shut/open test of sliding doors and horizontal roll-fronts)	-	5000	-
CLAUSE 7.3.2.3(Durability of sliding doors and horizontal roll-fronts)	-	5000	-
CLAUSE 7.3.3(Flaps)	-	5000	-
CLAUSE 7.3.3.1(Strength of bottom-hinged flaps)	-	5000	-
CLAUSE 7.3.3.2(Durability of flaps)	-	5000	-
CLAUSE 7.3.3.3(Drop test for top-hinged flaps)	-	5000	-
CLAUSE 7.3.4(Vertical Roll-Fronts)	-	5000	-
CLAUSE 7.3.4.1(Slam shut/open test of vertical roll-fronts)	-	5000	-
CLAUSE 7.3.4.2(Durability of vertical roll-fronts)	-	5000	-
CLAUSE 7.3.5(Extension Element)	-	5000	-
CLAUSE 7.3.5.2(Strength of extension elements)	-	5000	-
CLAUSE 7.3.5.3(Durability of extension elements)	-	5000	-
CLAUSE 7.3.5.4(Slam shut/open test of extension element)	-	5000	-
CLAUSE 7.3.5.5(Displacement of extension element bottoms)	-	5000	-
CLAUSE 7.3.5.6(Interlock test)	-	5000	-
CLAUSE 7.3.6(Locking and Latching Mechanism Tests)	-	5000	-
CLAUSE 7.3.6.2(Strength test for locking and latching mechanisms for extension elements)	-	5000	-
CLAUSE 7.3.6.3(Locking and latching mechanisms for doors, flaps and roll-fronts)	-	5000	-
CLAUSE 7.3.6.4(Durability test of locking and latching mechanisms)	-	5000	-
CLAUSE 7.3.7(Pull Force Test)	-	5000	-
CLAUSE 7.3.7(Pull Force Test)	-	5000	-
CLAUSE 7.3.8(Top Load Ease Cycle Test)	-	5000	-
CLAUSE 7.3.9(Durability Test for Units with Seating Surfaces – Cyclic Impact)	-	5000	-
CLAUSE 7.3.10("Drop Test – Dynamic – for Units with Seat Surfaces")	-	5000	-
CLAUSE 7.4.1.3(Sustained load test (overload))	-	5000	-
CLAUSE 7.4.1.4(Dislodgement test)	-	5000	-
CLAUSE 7.5(Stability Tests)	-	5000	-
CLAUSE 7.5.2.1("Units that can be adjusted to a Height of 1 000 mm or less")	-	5000	-
CLAUSE 7.5.2.2("Units that can be adjusted to a height of more than 1 000 mm")	-	5000	-
CLAUSE 7.5.3(Opening Doors, Extension Elements and Flaps, All Storage Units Unloaded)	-	5000	-
CLAUSE 7.5.6(Vertical Force Stability Test for Storage Units)	-	5000	-
CLAUSE 7.5.7(Stability Test for Pedestals/Storage Units with Seat Surfaces)	-	5000	-
CLAUSE 7.5.8("Dynamic Stability Test for Units with Castors")	-	5000	-
CLAUSE 7.5.9(Strength Test for Wall Attachments)	-	5000	-
Cl-6.1 (a)(Resistance to mechanical damage)	-	5000	-
Cl-6.1 (b)(Pencil hardness)	-	5000	-
Cl-6.1 (c)(Resistance to wet heat)	-	5000	-
Cl-6.1 (d)Cl-6.1 (d)(Resistance to dry heat)	-	5000	-
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	5000	-
Cl-6.1 (f)(Resistance to marking by cold oils and fats Resistance to marking by cold oils and fats)	-	5000	-
Cl-6.1 (g)(Adhesive performance)	-	5000	-
Cl-6.2 (a) 1(Breaking load)	-	5000	-
Cl-6.2 (a) 2(Elongation at break)	-	5000	-
Cl-6.2 (a) 3(Tear strength)	-	5000	-
Cl-6.2 (a) 4(Colour fastness to light)	-	5000	-
Cl-6.2 (a) 5(Colour fastness to rubbing)	-	5000	-
Cl-6.2 (a) 6(Colour fastness to perspiration)	-	5000	-
Cl-6.2 (a) 7(Colour fastness to water)	-	5000	-
Cl-6.2 (a) 8(Pilling resistance)	-	5000	-
Cl-6.2 (a) 9(Coating adhesion strength)	-	5000	-
Cl-6.2 (a) 10(Seam slippage)	-	5000	-
Cl-6.2 (a) 11(Resistance to damage by flexing)	-	5000	-
Cl-6.2 (a) 12(Abrasion resistance)	-	5000	-
Cl-6.2 (a) 13(Bursting strength)	-	5000	-
Cl-6.2 (a) 14(Resistance to cold)	-	5000	-
Cl-6.2 (b) 1(Tear strength)	-	5000	-
Cl-6.2 (b) 2(Flexing endurance)	-	5000	-
Cl-6.2 (b) 3(Finish adhesion)	-	5000	-
Cl-6.2 (b) 4(Colour fastness to artificial light)	-	5000	-
Cl-6.2 (b) 5(Colour fastness to rubbing)	-	5000	-
Cl-6.2 (b) 6(Colour fastness to water spotting)	-	5000	-
Cl-6.2 (b) 7(Water vapour permeability)	-	5000	-
Cl-6.2 (b) 8(Colour fastness to water)	-	5000	-
Cl-7.1(General)	-	5000	-
Cl-7.2.1(Shelves)	-	5000	-
Cl-7.2.2(Tops and Bottoms)	-	5000	-
Cl-7.2.3(Strength of Clothes Rails and their Supports)	-	5000	-
Cl-7.2.4(Strength of the Structure)	-	5000	-
Cl-7.3.1(Pivoted Doors)	-	5000	-
Cl-7.3.2(Sliding Doors and Horizontal Roll-fronts)	-	5000	-
Cl-7.3.3(Flaps)	-	5000	-
Cl-7.3.4(Vertical Roll-Fronts)	-	5000	-
Cl-7.3.5(Extension Elements)	-	5000	-
Cl-7.3.6(Locking and Latching Mechanism Test)	-	5000	-
Cl-7.3.7(Pull Force Test)	-	5000	-
Cl-7.3.8(Top Load Ease Cycle Test)	-	5000	-
Cl-7.3.9(Durability Test for Units with Seating Surfaces – Cyclic Impact)	-	5000	-
Cl-7.3.10(Drop Test – Dynamic – for Units with Seat Surfaces)	-	5000	-
Cl-7.4.1(Units Not Supported by the Floor)	-	5000	-
Cl-7.4.2(Units Supported by the Floor)	-	5000	-
Cl-7.5.1(General)	-	5000	-
Cl-7.5.2(Doors, Extension Elements and Flaps Closed, All Storage Units Unloaded)	-	5000	-
Cl-7.5.3(Opening Doors, Extension Elements and Flaps, All Storage Units Unloaded)	-	5000	-
Cl-7.5.4(Doors, Extension Elements and Flaps Opened and Unlocked)	-	5000	-
Cl-7.5.5(Doors, Extension Elements and Flaps Closed and Locked, All Storage Units Loaded)	-	5000	-
Cl-7.5.6(Vertical Force Stability Test for Storage Units)	-	5000	-
Cl-7.5.7(Stability Test for Pedestals/Storage Units with Seat Surfaces)	-	5000	-
Cl-7.5.8(Dynamic Stability Test for Units with Castors)	-	5000	-
Cl-7.5.9(Strength Test for Wall Attachments)	-	5000	-
Cl-9(Marking)	-	5000	-

14 Nov, 2027

-
-

IS 17632 (2022)

General Purpose Chairs and Stools - Specification

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 5(DIMENSIONS)	-	5000	-
CLAUSE 6(SURFACE PERFORMANCE)	-	5000	-
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	15000	-
CLAUSE 7.2.1(Forwards Overbalancing and Sideways Overbalancing for Chairs without Arms)	-	5000	-
CLAUSE 7.2.2(Rearwards Overbalancing)	-	5000	-
CLAUSE 7.2.3(Sideways Overbalancing for Chairs with Arms)	-	5000	-
CLAUSE 7.2.4(Sideways Overbalancing for Chairs with Arms)	-	5000	-
CLAUSE 7.3.1.1(Seat static load test)	-	5000	-
CLAUSE 7.3.1.2(Back static load test)	-	5000	-
CLAUSE 7.3.1.3(Armrests/Wings sideways static load test)	-	5000	-
CLAUSE 7.3.1.4(Arm downwards static load test)	-	5000	-
CLAUSE 7.3.1.5(Leg forward static load test)	-	5000	-
CLAUSE 7.3.1.6(Leg sideways static load test)	-	5000	-
CLAUSE 7.3.1.7(Diagonal base load test)	-	5000	-
CLAUSE 7.3.1.8(Foot rest static-load test)	-	5000	-
CLAUSE 7.3.2.1(Seat impact test)	-	5000	-
CLAUSE 7.3.2.2(Back impact test)	-	5000	-
CLAUSE 7.3.2.3(Arm impact test)	-	5000	-
CLAUSE 7.3.2.4(Drop test)	-	5000	-
CLAUSE 7.4.1(Seat Fatigue Test)	-	5000	-
CLAUSE 7.4.2(Back Fatigue Test)	-	5000	-
CLAUSE 7.4.3(Arm Rest Durability Test)	-	5000	-
Cl - 5(DIMENSIONS)	-	5000	-
Cl-6.1 (a)(Resistance to mechanical damage)	-	5000	-
Cl-6.1 (b)(Pencil hardness)	-	5000	-
Cl-6.1 (c)(Resistance to wet heat)	-	5000	-
Cl-6.1 (d)(Resistance to dry heat)	-	5000	-
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	5000	-
Cl-6.1 (f)(Resistance to marking by cold oils and fats)	-	5000	-
Cl-6.1 (g)(Adhesive performance)	-	5000	-
Cl-6.2 (a) 1(Breaking load)	-	5000	-
Cl-6.2 (a) 2(Elongation at break)	-	5000	-
Cl-6.2 (a) 3(Tear strength)	-	5000	-
Cl-6.2 (a) 4(Colour fastness to light)	-	5000	-
Cl-6.2 (a) 5(Colour fastness to rubbing)	-	5000	-
Cl-6.2 (a) 6(Colour fastness to perspiration)	-	5000	-
Cl-6.2 (a) 7(Colour fastness to water)	-	5000	-
Cl-6.2 (a) 8(Pilling resistance)	-	5000	-
Cl-6.2 (a) 9(Coating adhesion strength)	-	5000	-
Cl-6.2 (a) 10(Seam slippage)	-	5000	-
Cl-6.2 (a) 11(Resistance to damage by flexing)	-	5000	-
Cl-6.2 (a) 12(Abrasion resistance)	-	5000	-
Cl-6.2 (a) 13(Bursting strength)	-	5000	-
Cl-6.2 (a) 14(Resistance to cold)	-	5000	-
Cl-6.2 (b) 1(Tear strength)	-	5000	-
Cl-6.2 (b) 2(Flexing endurance)	-	5000	-
Cl-6.2 (b) 3(Finish adhesion)	-	5000	-
Cl-6.2 (b) 4(Colour fastness to artificial light)	-	5000	-
Cl-6.2 (b) 5(Colour fastness to rubbing)	-	5000	-
Cl-6.2 (b) 6(Colour fastness to water spotting)	-	5000	-
Cl-6.2 (b) 7(Water vapour permeability)	-	5000	-
Cl-6.2 (b) 8(Colour fastness to water)	-	5000	-
Cl-7.2.1(Forwards Overbalancing and Sideways Overbalancing for Chairs without Arms)	-	5000	-
Cl-7.2.2(Rearwards Overbalancing)	-	5000	-
Cl-7.2.3(Sideways Overbalancing for Chairs with Arms)	-	5000	-
Cl-7.2.4(Stools/ Poufs (All Directions))	-	5000	-
Cl-7.3.1(Static Load Test)	-	5000	-
Cl-7.3.2(Impact Test)	-	5000	-
Cl-7.4.1(Seat Fatigue Test)	-	5000	-
Cl-7.4.2(Back Fatigue Test)	-	5000	-
Cl-7.4.3(Arm Rest Durability)	-	5000	-
Cl-9(Marking)	-	5000	-
7.1(General test conditions)	-	5000	-

14 Nov, 2027

-
-

IS 17631 (2022)

Work Chairs - Specification

70000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
clause 4(DESIGN AND WORKMANSHIP)	-	5000	-
clause 5(DIMENSIONS)	-	5000	-
Cl-6.1 (a)(Resistance to mechanical damage)	-	5000	-
Cl-6.2 (a) (1)(For Fabric and Synthetic Leather:- Breaking load)	-	5000	-
Cl-7.3.1(Front Edge Overturning)	-	5000	-
Cl-7.3.2(Forwards Overturning)	-	5000	-
Cl-7.3.3(Forwards Overturning for Chairs with Foot Rest)	-	5000	-
Cl-7.3.4(Sideways Overturning for Chairs Without Arm Rests)	-	5000	-
Cl-6.1 (b)(Pencil hardness)	-	5000	-
Cl-6.1 (c)(Resistance to wet heat;)	-	5000	-
Cl-6.1 (d)(Resistance to dry heat;)	-	5000	-
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	5000	-
Cl-6.1 (f)(Resistance to marking by cold oils and fats;)	-	5000	-
Cl-6.1 (g)(Adhesive performance)	-	5000	-
Cl-6.2 (a) (2)(For Fabric and Synthetic Leather:- Elongation at break)	-	5000	-
Cl-6.2 (a) (3)(For Fabric and Synthetic Leather:- Tear strength)	-	5000	-
Cl-6.2 (a) (4)(For Fabric and Synthetic Leather:- Colour fastness to light)	-	5000	-
Cl-6.2 (a) (5)(For Fabric and Synthetic Leather:- Colour fastness to rubbing)	-	5000	-
Cl-6.2 (a) (6)(For Fabric and Synthetic Leather:- Colour fastness to perspiration)	-	5000	-
Cl-6.2 (a) (7)(For Fabric and Synthetic Leather:- Colour fastness to water)	-	5000	-
Cl-6.2 (a) (8)(For Fabric and Synthetic Leather:- Pilling resistance)	-	5000	-
Cl-6.2 (a) (9)(For Fabric and Synthetic Leather:- Coating adhesion strength)	-	5000	-
Cl-6.2 (a) (10)(For Fabric and Synthetic Leather:- Seam slippage)	-	5000	-
Cl-6.2 (a) (11)(For Fabric and Synthetic Leather:- Resistance to damage by flexing)	-	5000	-
Cl-6.2 (a) (12)(For Fabric and Synthetic Leather:- Abrasion resistance)	-	5000	-
Cl-6.2 (a) (13)(For Fabric and Synthetic Leather:- Bursting strength)	-	5000	-
Cl-6.2 (a) (14)(For Fabric and Synthetic Leather:- Resistance to cold)	-	5000	-
Cl-6.2 (b) (2)(For Natural Leather:- Flexing endurance)	-	5000	-
Cl-6.2 (b) (1)(For Natural Leather:- Tear strength)	-	5000	-
Cl-6.2 (b) (3)(For Natural Leather: Finish adhesion)	-	5000	-
Cl-6.2 (b) (4)(For Natural Leather: Colour fastness to artificial light)	-	5000	-
Cl-6.2 (b) (5)(For Natural Leather: Colour fastness to rubbing)	-	5000	-
Cl-6.2 (b) (6)(For Natural Leather: Colour fastness to water spotting)	-	5000	-
Cl-6.2 (b) (7)(For Natural Leather: Water vapour permeability)	-	5000	-
Cl-6.2 (b) (8)(For Natural Leather: Colour fastness to water)	-	5000	-
Cl-7.3.5(Sideways Overturning for Chairs With Arm Rests)	-	5000	-
Cl-7.3.6(Rearwards Overturning for Chairs Without Back Rest Inclination)	-	5000	-
Cl-7.3.7(Rearwards Overturning for Chairs with Backrest Inclination)	-	5000	-
Cl-7.4.1(Seat Front Edge Static Load Test)	-	5000	-
Cl-7.4.2(Combined Seat and Back Static Load Test)	-	5000	-
Cl-7.4.3(Arm Rest Downward Static Load Test — Central)	-	5000	-
Cl-7.4.4(Arm Rest Downward Static Load Test — Front)	-	5000	-
Cl-7.4.5(Arm Rest Sideways Static Load Test)	-	5000	-
Cl-7.4.6(Foot Rest Static Load Test)	-	5000	-
Cl-7.5.1(Seat and Back Durability)	-	5000	-
Cl-7.5.2(Arm Rest Durability)	-	5000	-
Cl-7.5.3(Swivel Test)	-	5000	-
Cl-7.5.4(Foot-rest Durability)	-	5000	-
Cl-7.5.5(Castor and Chair-Base Durability)	-	5000	-

14 Nov, 2027

-
-

IS 17633 (2022)

Tables and Desks - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(Design and workmanship)	-	5000	-
ClAUSE 5(Dimensions)	-	5000	-
CLAUSE 6(SURFACE PERFORMANCE REQUIRMENTS)	-	5000	-
CLAUSE 7.2.1(Stability Under Vertical Load)	-	5000	-
CLAUSE 7.2.1.1(Test for tables that can be set to a height of 950 mm or less)	-	5000	-
CLAUSE 7.2.1.2(" Test for Tables that can be set to a height greater than 950 mm")	-	5000	-
CLAUSE 7.2.2(Stability with Extension Elements Open Place the table on the floor surface)	-	5000	-
CLAUSE 7.2.3(Stability Under Horizontal Load)	-	5000	-
CLAUSE 7.2.3.1(Test for tables that can be set to a height of 950 mm or less)	-	5000	-
CLAUSE 7.2.3.2(" Test for Tables that can be set to a height greater than 950 mm")	-	5000	-
CLAUSE 7.3.1(Strength under Vertical Static Force)	-	5000	-
CLAUSE 7.3.1.1(Stated load)	-	5000	-
CLAUSE 7.3.1.2(For occasional heavy loads)	-	5000	-
CLAUSE 7.3.2(Strength under horizontal static force)	-	5000	-
CLAUSE 7.4.1(Durability under Vertical Force)	-	5000	-
CLAUSE 7.4.2(Durability of the Height Adjustment Mechanism)	-	5000	-
CLAUSE 7.5.1(Durability and Stiffness Under Horizontal Force)	-	5000	-
CLAUSE 7.5.2(Durability under Horizontal Force)	-	5000	-
CLAUSE 7.5.3(Stiffness of the Structure Under Horizontal Force)	-	5000	-
CLAUSE 7.6.1(Vertical Impact Test)	-	5000	-
CLAUSE 7.6.2(Vertical Impact Test for Glass Table Tops)	-	5000	-
CLAUSE 7.6.3(Vertical Impact Test for All Other Table Tops)	-	5000	-
CLAUSE 7.7(Deflection of Table Tops)	-	5000	-
CLAUSE 7.8(Durability of Tables with Castors)	-	5000	-
CLAUSE 7.9(Drop Test)	-	5000	-
Cl - 5(Dimensions)	-	5000	-
Cl-6 (a)(Resistance to mechanical damage)	-	5000	-
Cl-6 (b)(Pencil hardness)	-	5000	-
Cl-6 (c)(Resistance to wet heat)	-	5000	-
Cl-6 (d)(Resistance to dry heat)	-	5000	-
Cl-6 (e)(Resistance to marking by cold liquids)	-	5000	-
Cl-6 (f)(Resistance to marking by cold oils and fats)	-	5000	-
Cl-6 (g)(Adhesive performance)	-	5000	-
Cl-7.2.1(Stability Under Vertical Load)	-	5000	-
Cl-7.2.2(Stability with Extension Elements Open)	-	5000	-
Cl-7.2.3(Stability Under Horizontal Load)	-	5000	-
Cl-7.3.1(Strength under Vertical Static Force)	-	5000	-
Cl-7.3.2(Strength under horizontal static force)	-	5000	-
Cl-7.4.1(Durability under Vertical Force)	-	5000	-
Cl-7.4.2(Durability of the Height Adjustment Mechanism)	-	5000	-
Cl-7.5.1(General)	-	5000	-
Cl-7.5.2(Durability under Horizontal Force)	-	5000	-
Cl-7.5.3(Stiffness of the Structure Under Horizontal Force)	-	5000	-
Cl-7.6.1(General)	-	5000	-
Cl-7.6.2(Vertical Impact Test for Glass Table Tops)	-	5000	-
Cl-7.6.3(Vertical Impact Test for All Other Table Tops)	-	5000	-
Cl-7.7(Deflection of Table Tops)	-	5000	-
Cl-7.8(Durability of Tables with Castors)	-	5000	-
Cl-7.9(Drop Test)	-	5000	-
Cl-9(Marking)	-	5000	-
7.1(General test conditions)	-	5000	-

14 Nov, 2027

-
-

IS 996 (2025)

SINGLE PHASE ac INDUCTION MOTORS FOR GENERAL PURPOSE (Fouth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7(Dimensions)	-	2000	-
Cl-9.1(Mounting)	-	2000	-
Cl-9.2(Terminal Box)	-	2000	-
Cl-9.3(Mounting Constructions)	-	2000	-
Cl-9.3(Mounting Constructions)	-	2000	-
Cl-9.4(Constructional Features)	-	2000	-
Cl-9.5(Earthing)	-	2000	-
Cl-10.1(Enclosures)	-	2000	-
Cl-12.1(Torques)	-	2000	-
Cl-12.1.2(Momentary overload test)	-	2000	-
Cl-12.2(Temperature Rise)	-	2000	-
Cl-12.3(Short Time Rating)	-	2000	-
Cl-12.4(Method of Testing)	-	2000	-
Cl-12.5(Performance Values)	-	2000	-
Cl-12.6(Limits of Vibration Severity)	-	2000	-
Cl-12.7(Insulation Resistance)	-	2000	-
Cl-13.1(High Voltage Values)	-	2000	-
Cl-13.2(Moisture Proofness)	-	2000	-
Cl-13.3(Leakage Current)	-	2000	-
Cl-14(Winding Resistance Measurement)	-	2000	-
Cl-15(REDUCED VOLTAGE RUNNING UP TEST AT NO LOAD)	-	2000	-
Cl-16(NOISE LEVEL)	-	2000	-
Cl-17(OVER SPEED TEST)	-	2000	-
Cl-18(TERMINAL MARKING)	-	2000	-
Cl-12.1.1(Test for torues at rated voltage and frequency)	-	2000	-
Cl-12.1.1(Pull up Torque at rated voltage and frequency)	-	2000	-
Cl-12.1.1(Test for breakaway starting current at rated voltage and frequency)	-	2000	-
Cl-12.1.2(Breakaway (starting) torque at rated voltage and frequency)	-	2000	-
Cl-12.5.1(Test for full-load performance at rated voltage and frequency)	-	2000	-
Cl-21.5(Acceptance Tests)	-	2000	-
Cl-7(Dimensions)	-	2000	-
Cl-9.1(Mounting)	-	2000	-
Cl-9.2(Terminal Box)	-	2000	-
Cl-9.3(Mounting Constructions)	-	2000	-
Cl-9.3(Mounting Constructions)	-	2000	-
Cl-9.4(Constructional Features)	-	2000	-
Cl-9.5(Earthing)	-	2000	-
Cl-10.1(Enclosures)	-	2000	-
Cl-12.1(Torques)	-	2000	-
Cl-12.1.2(Momentary overload test)	-	2000	-
Cl-12.2(Temperature Rise)	-	2000	-
Cl-12.3(Short Time Rating)	-	2000	-
Cl-12.4(Method of Testing)	-	2000	-
Cl-12.5(Performance Values)	-	2000	-
Cl-12.6(Limits of Vibration Severity)	-	2000	-
Cl-12.7(Insulation Resistance)	-	2000	-
Cl-13.1(High Voltage Values)	-	2000	-
Cl-13.2(Moisture Proofness)	-	2000	-
Cl-13.3(Leakage Current)	-	2000	-
Cl-14(Winding Resistance Measurement)	-	2000	-
Cl-15(REDUCED VOLTAGE RUNNING UP TEST AT NO LOAD)	-	2000	-
Cl-16(NOISE LEVEL)	-	2000	-
Cl-17(OVER SPEED TEST)	-	2000	-
Cl-18(TERMINAL MARKING)	-	2000	-
Cl-12.1.1(Test for torues at rated voltage and frequency)	-	2000	-
Cl-12.1.1(Pull up Torque at rated voltage and frequency)	-	2000	-
Cl-12.1.1(Test for breakaway starting current at rated voltage and frequency)	-	2000	-
Cl-12.1.2(Breakaway (starting) torque at rated voltage and frequency)	-	2000	-
Cl-12.5.1(Test for full-load performance at rated voltage and frequency)	-	2000	-
Cl-21.5(Acceptance Tests)	-	2000	-

14 Nov, 2027

-
Included w.e.f. 09.10.2025

IS 16542 (2016)

Direct insertion type storage water tank for all glass evacuated tubes solar collector - Specification

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3(Ideal Heating Test)	-	5000	-
8.2(Leakage Test)	-	5000	-
8.4(Integral Test)	-	5000	-
8.5(Performance Test)	-	5000	-
7.6(Thermal Shock Test for Inner Sealing)	-	5000	-
7.7(Thermal Shock Test for outer Sealing)	-	5000	-
6(GENERAL REQUIREMENTS)	-	5000	-
8.1(Measurement of Storage Water Tank Capacity)	-	5000	-
8.3(Ideal Heating Test)	-	5000	-
8.2(Leakage Test)	-	5000	-
8.4(Integral Test)	-	5000	-
8.5(Performance Test)	-	5000	-
7.6(Thermal Shock Test for Inner Sealing)	-	5000	-
7.7(Thermal Shock Test for outer Sealing)	-	5000	-
6(GENERAL REQUIREMENTS)	-	5000	-
8.1(Measurement of Storage Water Tank Capacity)	-	5000	-

14 Nov, 2027

-
Included w.e.f. 29.08.2025 Excluding Material as per Clause 5

IS 18112 (2025)

DIGITAL TELEVISION RECEIVER FOR SATELLITE BROADCAST TRANSMISSION SPECIFICATION (First Revision)

211500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.4, Table-2, ii)(RF characteristics to be supported by the DTV receiver)	-	15000	-
Clause 4.3(Specifications)	-	15000	-
Clause 4.5(Safety Requirements)	-	15000	-
Clause 5(Marking)	-	15000	-
Clause 6(Operating Life Test)	-	15000	-
Clause 4.1, Table-1, i) a)(Hardware specification)	-	15000	-
Clause 4.1, Table-1, i) b)(Decompression and decoding of SDTV video)	-	15000	-
Clause 4.1, Table-1, i) c)(Decompression and decoding of HDTV video)	-	15000	-
Clause 4.1, Table-1, i) d)(Decompression and decoding of audio)	-	15000	-
Clause 4.1, Table-1, i) e)(Active Format descriptors)	-	15000	-
Clause 4.1, Table-1, i) f)(Captioning and Sub-titling)	-	15000	-
Clause 4.1, Table-1, i) g)(Teletext)	-	15000	-
Clause 4.1, Table-1, i) h)(Multi-language support)	-	15000	-
Clause 4.1, Table-1, i) j)(DTV receiver mixed Audio Description)	-	15000	-
Clause 4.1, Table-1, i) k)(Broadcast mixed audio description)	-	15000	-
Clause 4.1, Table-1, i) m)(Service demultiplexing)	-	15000	-
Clause 4.1, Table-1, i) n)(Data services)	-	15000	-
Clause 4.1, Table-1, i) p)(OSD)	-	15000	-
Clause 4.1, Table-1, i) q)(DTV character set)	-	15000	-
Clause 4.1, Table-1, i) r)(Electronic Service Guide (ESG) ‘Now/Next’)	-	15000	-
Clause 4.1, Table-1, i) s)(Time)	-	15000	-
Clause 4.1, Table-1, i) t)(Digital TV output)	-	15000	-
Clause 4.4, Table-2, i) b)(Frequency)	-	15000	-
Clause 4.4, Table-2, i) a)(Input voltage range)	-	15000	-
Clause 4.1,Table-1, ii) a)(Demodulation and FEC decoding)	-	15000	-
Clause 4.1, Table-1, ii) b)(DTV Receiver Installation)	-	15000	-
Clause 4.1, Table-1, ii) c)(Network evolution)	-	15000	-
Clause 4.4, Table-2, iii) c)(RF input impedance)	-	15000	-
Clause 4.1, Table-1, ii) d)(Services available)	-	15000	-
Clause 4.1, Table-1, ii) e)(Selection via Service List)	-	15000	-
Clause 4.1, Table-1, ii) f)(Selection via Numeric Entry)	-	15000	-
Clause 4.1, Table-1, ii) g)(Favourite Channel list)	-	15000	-
Clause 4.1, Table-1, ii) h)(Hidden Services)	-	15000	-
Clause 4.4, Table-2, iii) b)(Input frequency range)	-	15000	-
Clause 4.1, Table-1, ii) j)(Logical Channel Number for Satellite services)	-	15000	-
Clause 4.1, Table-1, ii) k)(RF input signal)	-	15000	-
Clause 4.1, Table-1, ii) m)(LNB supply current)	-	15000	-
Clause 4.1, Table-1, ii) n)(LNB supply voltage)	-	15000	-
Clause 4.1, Table-1, ii) p)(LNB Control)	-	15000	-
Clause 4.1, Table-1, ii) q)(Modulation/Demodulation parameters for DVB-S & DVB-S2 standard)	-	15000	-
Clause 4.4, Table-2, iii) a)(Input level per carrier)	-	15000	-
Clause 4.4, Table-2, iv) c)(RF input impedance)	-	15000	-
Clause 4.4, Table-2, iv) b)(Input frequency range)	-	15000	-
Clause 4.4, Table-2, iv) a)(Input level per carrier)	-	15000	-
Clause 4.4, Table-2, v)(Symbol rate)	-	15000	-
Clause 4.4, Table-2, vi)(RF input return loss)	-	15000	-
Clause 4.4, Table-2, vii)(DisEqC)	-	15000	-
Clause 4.4, Table-2, viii)(Operating ambient temperature range)	-	15000	-
Clause 4.4, Table-2, ix)(Operating humidity range)	-	15000	-
Clause 4.1, Table-1, iii) a)(Interfaces, Connectors)	-	15000	-
Clause 4.1, Table-1, iv)(Automatic software upgrade mechanism)	-	15000	-
Clause 4.1, Table-1, v) a)(Remote Control)	-	15000	-
Clause 4.1, Table-1, v) b)(Easy to use and simple documentation)	-	15000	-
Clause 3.1, Table-1, v) c)(Support package)	-	15000	-
Clause 4.4, Table-2, ii)(RF characteristics to be supported by the DTV receiver)	-	15000	-
Clause 4.3(Specifications)	-	15000	-
Clause 4.5(Safety Requirements)	-	15000	-
Clause 5(Marking)	-	15000	-
Clause 6(Operating Life Test)	-	15000	-
Clause 4.1, Table-1, i) a)(Hardware specification)	-	15000	-
Clause 4.1, Table-1, i) b)(Decompression and decoding of SDTV video)	-	15000	-
Clause 4.1, Table-1, i) c)(Decompression and decoding of HDTV video)	-	15000	-
Clause 4.1, Table-1, i) d)(Decompression and decoding of audio)	-	15000	-
Clause 4.1, Table-1, i) e)(Active Format descriptors)	-	15000	-
Clause 4.1, Table-1, i) f)(Captioning and Sub-titling)	-	15000	-
Clause 4.1, Table-1, i) g)(Teletext)	-	15000	-
Clause 4.1, Table-1, i) h)(Multi-language support)	-	15000	-
Clause 4.1, Table-1, i) j)(DTV receiver mixed Audio Description)	-	15000	-
Clause 4.1, Table-1, i) k)(Broadcast mixed audio description)	-	15000	-
Clause 4.1, Table-1, i) m)(Service demultiplexing)	-	15000	-
Clause 4.1, Table-1, i) n)(Data services)	-	15000	-
Clause 4.1, Table-1, i) p)(OSD)	-	15000	-
Clause 4.1, Table-1, i) q)(DTV character set)	-	15000	-
Clause 4.1, Table-1, i) r)(Electronic Service Guide (ESG) ‘Now/Next’)	-	15000	-
Clause 4.1, Table-1, i) s)(Time)	-	15000	-
Clause 4.1, Table-1, i) t)(Digital TV output)	-	15000	-
Clause 4.4, Table-2, i) b)(Frequency)	-	15000	-
Clause 4.4, Table-2, i) a)(Input voltage range)	-	15000	-
Clause 4.1,Table-1, ii) a)(Demodulation and FEC decoding)	-	15000	-
Clause 4.1, Table-1, ii) b)(DTV Receiver Installation)	-	15000	-
Clause 4.1, Table-1, ii) c)(Network evolution)	-	15000	-
Clause 4.4, Table-2, iii) c)(RF input impedance)	-	15000	-
Clause 4.1, Table-1, ii) d)(Services available)	-	15000	-
Clause 4.1, Table-1, ii) e)(Selection via Service List)	-	15000	-
Clause 4.1, Table-1, ii) f)(Selection via Numeric Entry)	-	15000	-
Clause 4.1, Table-1, ii) g)(Favourite Channel list)	-	15000	-
Clause 4.1, Table-1, ii) h)(Hidden Services)	-	15000	-
Clause 4.4, Table-2, iii) b)(Input frequency range)	-	15000	-
Clause 4.1, Table-1, ii) j)(Logical Channel Number for Satellite services)	-	15000	-
Clause 4.1, Table-1, ii) k)(RF input signal)	-	15000	-
Clause 4.1, Table-1, ii) m)(LNB supply current)	-	15000	-
Clause 4.1, Table-1, ii) n)(LNB supply voltage)	-	15000	-
Clause 4.1, Table-1, ii) p)(LNB Control)	-	15000	-
Clause 4.1, Table-1, ii) q)(Modulation/Demodulation parameters for DVB-S & DVB-S2 standard)	-	15000	-
Clause 4.4, Table-2, iii) a)(Input level per carrier)	-	15000	-
Clause 4.4, Table-2, iv) c)(RF input impedance)	-	15000	-
Clause 4.4, Table-2, iv) b)(Input frequency range)	-	15000	-
Clause 4.4, Table-2, iv) a)(Input level per carrier)	-	15000	-
Clause 4.4, Table-2, v)(Symbol rate)	-	15000	-
Clause 4.4, Table-2, vi)(RF input return loss)	-	15000	-
Clause 4.4, Table-2, vii)(DisEqC)	-	15000	-
Clause 4.4, Table-2, viii)(Operating ambient temperature range)	-	15000	-
Clause 4.4, Table-2, ix)(Operating humidity range)	-	15000	-
Clause 4.1, Table-1, iii) a)(Interfaces, Connectors)	-	15000	-
Clause 4.1, Table-1, iv)(Automatic software upgrade mechanism)	-	15000	-
Clause 4.1, Table-1, v) a)(Remote Control)	-	15000	-
Clause 4.1, Table-1, v) b)(Easy to use and simple documentation)	-	15000	-
Clause 3.1, Table-1, v) c)(Support package)	-	15000	-

14 Nov, 2027

-
Included w.e.f 09.09.2025 Exclusion: Clause 4.6 (Electromagnetic Compatibility (EMC) Requirements)

IS 17550 : Part 3 (2025)

Household Refrigerating Appliances - Characteristics and Methods Of Test Part 3 Energy Consumption and Volume (First Revision)

130000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1, Annex A(set up for energy consumption)	-	25000	-
Clause 4.2, Annex B(Steady state power consumption)	-	25000	-
Clause 4.3, Annex C(Defrost and Recovery Energy and Temperature Change)	-	25000	-
Clause 4.4, Annex D(Defrost Frequency)	-	25000	-
Clause 4.5, Annex E(Number of Test Points and Interpolation)	-	25000	-
Clause 4.6, Annex G(Load Processing Efficiency)	-	25000	-
Clause 4.7, Annex F(Specified Auxiliaries)	-	25000	-
Clause 4.8, Annex H(Volume determination)	-	8000	-
Clause 4.8.1, Annex H(Rated total volume)	-	8000	-
Clause 5, 5.1, 5.2 Table 1(TARGET TEMPERATURES FOR ENERGY DETERMINATION)	-	25000	-
Clause 6, 6.1 to 6.8(DETERMINATION OF ENERGY CONSUMPTION)	-	25000	-
Clause 4.1, Annex A(set up for energy consumption)	-	25000	-
Clause 4.2, Annex B(Steady state power consumption)	-	25000	-
Clause 4.3, Annex C(Defrost and Recovery Energy and Temperature Change)	-	25000	-
Clause 4.4, Annex D(Defrost Frequency)	-	25000	-
Clause 4.5, Annex E(Number of Test Points and Interpolation)	-	25000	-
Clause 4.6, Annex G(Load Processing Efficiency)	-	25000	-
Clause 4.7, Annex F(Specified Auxiliaries)	-	25000	-
Clause 4.8, Annex H(Volume determination)	-	8000	-
Clause 4.8.1, Annex H(Rated total volume)	-	8000	-
Clause 5, 5.1, 5.2 Table 1(TARGET TEMPERATURES FOR ENERGY DETERMINATION)	-	25000	-
Clause 6, 6.1 to 6.8(DETERMINATION OF ENERGY CONSUMPTION)	-	25000	-

14 Nov, 2027

-
Included w.e.f.12.09.2025

IS 302 : Part 2 : Sec 74 (2024)

Household and Similar Electrical Appliancesï¿½Safety Part 2 Particular Requirements Section 74 Portable immersion heaters

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	500	-
8(Protection against access to live parts)	-	5000	-
10(Power input and current)	-	5000	-
10(Power input and current)	-	5000	-
11(Heating)	-	5000	-
13.1 &13.2(Leakage current test)	-	5000	-
13.1 &13.3(Electric strength test)	-	1000	-
14(Transient overvoltages)	-	1000	-
15(Moisture resistance)	-	5000	-
15.3(Moisture resistance)	-	5000	-
16.1 &16.2(Leakage current test)	-	1000	-
16.1 & 16.3(Electric strength test)	-	1000	-
17(Overload protection of transformers and associated circuits)	-	1000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	1000	-
20.1(Stability and mechanical hazards)	-	1000	-
20.2(Stability and mechanical hazards)	-	1000	-
21(Mechanical strength)	-	1000	-
22(Construction)	-	1000	-
23(Internal wiring)	-	1000	-
24(Components)	-	1000	-
24.101(Components)	-	1000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	1000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	1000	-
30(Resistance to heat and fire)	-	1000	-
30.101(Resistance to heat and fire)	-	1000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-
7(Marking and instructions)	-	1000	-
8(Protection against access to live parts)	-	1000	-
10(Power input and current)	-	1000	-
10(Power input and current)	-	1000	-
11(Heating)	-	1000	-
13.1 &13.2(Leakage current test)	-	1000	-
13.1 &13.3(Electric strength test)	-	1000	-
14(Transient overvoltages)	-	1000	-
15(Moisture resistance)	-	1000	-
15.3(Moisture resistance)	-	1000	-
16.1 &16.2(Leakage current test)	-	1000	-
16.1 & 16.3(Electric strength test)	-	1000	-
17(Overload protection of transformers and associated circuits)	-	1000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	1000	-
20.1(Stability and mechanical hazards)	-	1000	-
20.2(Stability and mechanical hazards)	-	1000	-
21(Mechanical strength)	-	1000	-
22(Construction)	-	1000	-
23(Internal wiring)	-	1000	-
24(Components)	-	1000	-
24.101(Components)	-	1000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	1000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	1000	-
30(Resistance to heat and fire)	-	1000	-
30.101(Resistance to heat and fire)	-	1000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-

14 Nov, 2027

-
Included w.e.f.11.08.2025 exclusion Cl 19.11.4.1 TO Cl 19.11.4.8(EMI/EMC)

IS 302 : Part 2 : Sec 209 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 209 low speed food grinding machines

37500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 32 302-2-209 : 1994(Radiation Hazards)	-	500	-
Cl. 31 302-2-209 : 1994(Resistance to Rusting)	-	1000	-
Cl. 30 302-2-209 : 1994(Resistance to Heat Fire & Tracking )	-	1000	-
Cl. 29 302-2-209 : 1994(Clearances, Creepage Distances & Solid insulation )	-	2000	-
Cl. 28 302-2-209 : 1994(Screws & Connections)	-	1000	-
Cl. 27 302-2-209 : 1994(Provision for Earthing )	-	1000	-
Cl. 26 302-2-209 : 1994(Terminals for External conductors )	-	1000	-
Cl. 25 302-2-209 : 1994(Supply Connection & External Flexible Cords)	-	1000	-
Cl. 24 302-2-209 : 1994(Components)	-	1000	-
Cl. 23 302-2-209 : 1994(Internal Wiring)	-	1000	-
Cl. 22 302-2-209 : 1994(Construction )	-	1000	-
Cl. 21 302-2-209 : 1994(Mechanical strength)	-	1000	-
Cl. 20 302-2-209 : 1994(Stability & Mechanical Hazards)	-	1000	-
Cl. 19 302-2-209 : 1994(Abnormal Operation )	-	1000	-
Cl. 18 302-2-209 : 1994(Endurance)	-	3000	-
Cl. 17 302-2-209 : 1994(Overload Protection of Transformers and Associated Circuit)	-	1000	-
Cl. 16 302-2-209 : 1994(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	1000	-
Cl. 15 302-2-209 : 1994(Moisture Resistance Test )	-	3000	-
Cl. 14 302-2-209 : 1994(Radio and television interference suppression / Transient over voltages)	-	1000	-
Cl. 13 302-2-209 : 1994(Leakage Current & Electric Strength at Operating Temperature)	-	1000	-
Cl. 11 302-2-209 : 1994(Temperature Rise)	-	2000	-
Cl. 10 302-2-209 : 1994(Power Input and Current )	-	1000	-
Cl. 9 302-2-209 : 1994(Starting of motor operated appliances)	-	1000	-
Cl. 8 302-2-209 : 1994(Protection Against Electric Shock )	-	1000	-
Cl. 7 302-2-209 : 1994(Marking)	-	1000	-
(CI. 6 IS 302-2-209 : 1994(Classification )	-	1000	-
Cl. 5 IS 302-2-209 :1994(Rating)	-	1000	-
Cl. 32 302-2-209 : 1994(Radiation Hazards)	-	1000	-
Cl. 31 302-2-209 : 1994(Resistance to Rusting)	-	1000	-
Cl. 30 302-2-209 : 1994(Resistance to Heat Fire & Tracking )	-	1000	-
Cl. 29 302-2-209 : 1994(Clearances, Creepage Distances & Solid insulation )	-	1000	-
Cl. 28 302-2-209 : 1994(Screws & Connections)	-	1000	-
Cl. 27 302-2-209 : 1994(Provision for Earthing )	-	1000	-
Cl. 26 302-2-209 : 1994(Terminals for External conductors )	-	1000	-
Cl. 25 302-2-209 : 1994(Supply Connection & External Flexible Cords)	-	1000	-
Cl. 24 302-2-209 : 1994(Components)	-	1000	-
Cl. 23 302-2-209 : 1994(Internal Wiring)	-	1000	-
Cl. 22 302-2-209 : 1994(Construction )	-	1000	-
Cl. 21 302-2-209 : 1994(Mechanical strength)	-	1000	-
Cl. 20 302-2-209 : 1994(Stability & Mechanical Hazards)	-	1000	-
Cl. 19 302-2-209 : 1994(Abnormal Operation )	-	3000.03	-
Cl. 18 302-2-209 : 1994(Endurance)	-	3000	-
Cl. 17 302-2-209 : 1994(Overload Protection of Transformers and Associated Circuit)	-	1000	-
Cl. 16 302-2-209 : 1994(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	1000	-
Cl. 15 302-2-209 : 1994(Moisture Resistance Test )	-	2000	-
Cl. 14 302-2-209 : 1994(Radio and television interference suppression / Transient over voltages)	-	1000	-
Cl. 13 302-2-209 : 1994(Leakage Current & Electric Strength at Operating Temperature)	-	1000	-
Cl. 11 302-2-209 : 1994(Temperature Rise)	-	2000	-
Cl. 10 302-2-209 : 1994(Power Input and Current )	-	1000	-
Cl. 9 302-2-209 : 1994(Starting of motor operated appliances)	-	1000	-
Cl. 8 302-2-209 : 1994(Protection Against Electric Shock )	-	1000	-
Cl. 7 302-2-209 : 1994(Marking)	-	1000	-
(CI. 6 IS 302-2-209 : 1994(Classification )	-	1000	-
Cl. 5 IS 302-2-209 :1994(Rating)	-	1000	-

14 Nov, 2027

-
Included w.e.f. 21.08.2025 Exclusion: "19.11.4.1 (Electrostatic discharges) 19.11.4.2 (Radiated fields) 19.11.4.3 (Fast transient bursts) 19.11.4.4 (Surge immunity test) 19.11.4.5 (Immunity to conducted discharges) 19.11.4.6 (Class 3 Voltage dips and interruptions) 19.11.4.7 (Harmonics)"

IS 302 : Part 2 : Sec 8 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 8 Shavers, Hair Clippers and Similar Appliances (First Revision)

29500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	500	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
11(Heating)	-	3000	-
12(Charging of metal-ion batteries)	-	2000	-
13.1 &13.2(Leakage current test)	-	3000	-
13.1 &13.3(Electric strength test)	-	3000	-
14(Transient overvoltages)	-	3000	-
15(Moisture resistance)	-	3000	-
15.3(Moisture resistance)	-	3000	-
16.1 &16.2(Leakage current test)	-	3000	-
16.1 & 16.3(Electric strength test)	-	2000	-
17(Overload protection of transformers and associated circuits)	-	2000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	2000	-
19.101(Abnormal operation)	-	2000	-
20.1(Stability and mechanical hazards)	-	2000	-
20.2(Stability and mechanical hazards)	-	2000	-
21(Mechanical strength)	-	2000	-
21.101(Mechanical strength)	-	2000	-
21.102(Mechanical strength)	-	2000	-
21.103(Mechanical strength)	-	2000	-
22(Construction)	-	2000	-
22.101(Construction)	-	2000	-
22.102(Construction)	-	2000	-
22.103(Construction)	-	2000	-
23(Internal wiring)	-	2000	-
24(Components)	-	2000	-
25("Supply connection and external flexible cords")	-	2000	-
26("Terminals for external conductors")	-	2000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	2000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	2000	-
31(Resistance to rusting)	-	2000	-
32("Radiation, toxicity and similar hazards")	-	2000	-
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	3000	-
10(Power input and current)	-	3000	-
11(Heating)	-	3000	-
12(Charging of metal-ion batteries)	-	2000	-
13.1 &13.2(Leakage current test)	-	3000	-
13.1 &13.3(Electric strength test)	-	3000	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	3000	-
15.3(Moisture resistance)	-	3000	-
16.1 &16.2(Leakage current test)	-	3000	-
16.1 & 16.3(Electric strength test)	-	2000	-
17(Overload protection of transformers and associated circuits)	-	2000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	2000	-
19.101(Abnormal operation)	-	2000	-
20.1(Stability and mechanical hazards)	-	2000	-
20.2(Stability and mechanical hazards)	-	2000	-
21(Mechanical strength)	-	2000	-
21.101(Mechanical strength)	-	2000	-
21.102(Mechanical strength)	-	2000	-
21.103(Mechanical strength)	-	2000	-
22(Construction)	-	2000	-
22.101(Construction)	-	2000	-
22.102(Construction)	-	2000	-
22.103(Construction)	-	2000	-
23(Internal wiring)	-	2000	-
24(Components)	-	2000	-
25("Supply connection and external flexible cords")	-	2000	-
26("Terminals for external conductors")	-	2000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	2000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	2000	-
31(Resistance to rusting)	-	2000	-
32("Radiation, toxicity and similar hazards")	-	2000	-

14 Nov, 2027

IS 302 : Part 2 : Sec 11 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 11 tumbler dryers

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(GENERAL REQUIREMENT)	-	1000	-
4(GENERAL NOTES ON TESTS)	-	1000	-
5(RATING)	-	1000	-
6(CLASSIFICATION)	-	1000	-
7(MARKING)	-	1000	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	2000	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	4000	-
10(INPUT AND CURRENT)	-	2000	-
11(HEATING)	-	5000	-
12(OPERATION TJNDER OVERLOAD CONDITIONS OF APPLIANCES WITH HEATING ELEMENTS)	-	1000	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	1000	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	1000	-
15(MOISTURE RESISTANCE)	-	5000	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	2000	-
17(OVERLOAD PROTECTION)	-	2000	-
18(ENDURANCE )	-	4000	-
19(ABNORMAL OPERATION)	-	5000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	2000	-
21(MECHANICAL STRENGTH)	-	2000	-
22(CONSTRUCTION)	-	2000	-
23(INTERNAL WIRING)	-	1000	-
24(COMPONENTS)	-	2000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	2000	-
27(PROVISION FOR EARTHING)	-	2000	-
28(SCREWS AND CONNECTIONS)	-	1000	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	4000	-
30(RESISTANCE TO HEAT, FIRE AND TACKING)	-	2000	-
31(RESISTANCE TO RUSTING)	-	3000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	4000	-
101.1(Type Tests)	-	22000	-
101.2(Acceptance Tests)	-	22000	-
101.3(Routine Tests)	-	10000	-
3(GENERAL REQUIREMENT)	-	1000	-
4(GENERAL NOTES ON TESTS)	-	4000	-
5(RATING)	-	2000	-
6(CLASSIFICATION)	-	2000	-
7(MARKING)	-	2000	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	4000	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	3000	-
10(INPUT AND CURRENT)	-	4000	-
11(HEATING)	-	12000	-
12(OPERATION TJNDER OVERLOAD CONDITIONS OF APPLIANCES WITH HEATING ELEMENTS)	-	4000	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	2000	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	3000	-
15(MOISTURE RESISTANCE)	-	5000	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	5000	-
17(OVERLOAD PROTECTION)	-	5000	-
18(ENDURANCE )	-	5000	-
19(ABNORMAL OPERATION)	-	4000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	4000	-
21(MECHANICAL STRENGTH)	-	4000	-
22(CONSTRUCTION)	-	4000	-
23(INTERNAL WIRING)	-	4000	-
24(COMPONENTS)	-	4000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	5000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	5000	-
27(PROVISION FOR EARTHING)	-	5000	-
28(SCREWS AND CONNECTIONS)	-	5000	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	6000	-
30(RESISTANCE TO HEAT, FIRE AND TACKING)	-	8000	-
31(RESISTANCE TO RUSTING)	-	8000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	10000	-
101.1(Type Tests)	-	12000	-
101.2(Acceptance Tests)	-	22000	-
101.3(Routine Tests)	-	2500	-

14 Nov, 2027

-
Included w.e.f 04.07.2025 Exclusion: Cl 19.11.4.1-19.11.4.7(EMI/EMC)

IS 4250 (2025)

Electric Food-Mixers (Liquidizers and Grinders) and Centrifugal Juicers ï¿½ Specification ( Second Revision )

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirements)	-	1500	-
Cl-5(General Conditions for the tests)	-	1500	-
Cl-6(Classification)	-	1500	-
Cl-7(Marking)	-	1000	-
Cl-8(Safety Requirements)	-	1000	-
Cl-9(Endurance fpr motor and base assembly)	-	2500	-
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	2500	-
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	2500	-
Cl-10.4(Idli Batter)	-	2500	-
Cl-10.5(Operational Tests for Juicers)	-	2500	-
Cl-11(Temperature Withstand Test for Bowl)	-	2500	-
Cl-12.1(Test for Switches)	-	1500	-
Cl-13(Strength of Assembly)	-	1500	-
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	1500	-
Cl-14.2, Table-2 (ii)(Power input and current)	-	1500	-
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	1500	-
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	2500	-
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	1500	-
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	1500	-
Cl-4(General Requirements)	-	1500	-
Cl-5(General Conditions for the tests)	-	1500	-
Cl-6(Classification)	-	1500	-
Cl-7(Marking)	-	500	-
Cl-8(Safety Requirements)	-	1000	-
Cl-9(Endurance fpr motor and base assembly)	-	2500	-
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	2500	-
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	2500	-
Cl-10.4(Idli Batter)	-	2500	-
Cl-10.5(Operational Tests for Juicers)	-	2500	-
Cl-11(Temperature Withstand Test for Bowl)	-	2500	-
Cl-12.1(Test for Switches)	-	2500	-
Cl-13(Strength of Assembly)	-	2500	-
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	1500	-
Cl-14.2, Table-2 (ii)(Power input and current)	-	1500	-
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	1500	-
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	1500	-
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	1500	-
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	1500	-

14 Nov, 2027

-
Included w.e.f 07.05.2025 Exclusion Cl 19.11.4.1- 19.11.4.7(EMI/EMC)

IS 17550 : Part 2 (2024)

Household Refrigerating Appliances - Characteristics and Test Methods Part 2 Performance Requirements (First Revision)

335000 View breakup
-

Clause No.	Exclusion	Remark
6(Storage Test)	-	-
7(Cooling Capacity Test)	-	-
8(Freezing Capacity Test)	-	-
9("Automatic Ice-Making Capacity Test")	-	-
Cl. No.4.6 & Annex A(PULL-DOWN TEST)	-	-
Cl. No.4.6(b) & Annex B("Wine Storage Appliances And Compartments; Storage Test")	-	-
Cl. No.4.6(C) & AnnexC("Temperature Rise Test ")	-	-
Cl. No.4.6(d) & Annex D("Water Vapour Condensation Test ")	-	-

14 Nov, 2027

-
Included w.e.f 27.03.2025

IS 17550 : Part 1 (2024)

Household Refrigerating Appliances - Characteristics and Test Methods Part 1 General Requirements (First Revision)

220000 View breakup
-

Clause No.	Exclusion	Remark
5(MARKING)	-	-
8(MATERIALS, DESIGN, AND MANUFACTURE)	-	-
9(Testing The Air Tightness Of Door Or Lid Seal(S))	-	-
10(Testing The Opening Force Of Door(S) Or Lid(S))	-	-
11(Testing The Durability Of Hinges And Handles Of Door(S) And Lid(S)	-	-
12(Testing The Mechanical Strength Of Shelves And Similar Components)	-	-
14(Ice-Making Test (If Applicable))	-	-
15(Test For Absence Of Odour And Taste)	-	-
16(Safety Requirements)	-	-

14 Nov, 2027

-
Included w.e.f 27.03.2025

IS 10617 (2018)

Hermetic compressors - Specification (Second Revision)

950000 View breakup
For all type of compressor cooling capacity- Upto 0.75 kW- Rs. 9,50,000/- from 0.75 kW to 2.5 kW - Rs. 11,50,000/- from 2.5 kW to 5 kW - Rs. 13,50,000/- from 5 kW to 10.5 kW - Rs. 15,50,000/- from 10.5 kW to 17.5 kW - Rs. 18,50,000/- from 17.5 kW to 24.5 kW - Rs. 21,50,000/- from 24.5 kW to 31.5 kW - Rs. 25,50,000/- from 31.5 kW to 38.5 kW - Rs. 30,50,000/- from 38.5 kW to 45 kW - Rs. 35,50,000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1 & 5.1 -Table 2, 3, 4,5(Compressor Performance Test & Compressor Capacity Rating Test)	-	350000	For all type of compressor cooling capacity from 17.5 kW to 24.5 kW - Rs. 21,50,000/- 24.5 kW to 31.5 kW - Rs. 25,50,000/- 31.5 kW to 38.5 kW - Rs. 30,50,000/- 38.5 kW to 45 kW - Rs. 35,50,000/
Cl. 4 of IS:10617:2018(10617)	-	5000	-
Cl. 5,5.1 of IS:10617:2018(10617)	-	350000	-
Cl.6.1.1 of IS:10617:2018(10617)	-	350000	-
Cl. 6.1.2, 6.1.2.1 of IS:10617:2018(10617)	-	100000	-
Cl. 6.1.2.2 of IS:10617:2018(10617)	-	10000	-
Cl. 6.1.3 of IS:10617(10617)	-	190000	-
Cl. 6.1.4 of IS:10617:2018(10617)	-	30000	-
Cl. 6.1.5 of IS:10617:2018(10617)	-	30000	-
Cl. 6.1.6 of IS:10617:2018(10617)	-	45000	-
Cl. 6.1.7 of IS:10617:2018(10617)	-	50000	-
Cl. 7, 7.1 of IS:10617:2018(10617)	-	150000	-
Cl. 8, 8.1, 8.2, 8.3, 8.4, 8.5 of IS:10617:2018(10617)	-	280000	-
Cl. 9 of IS:10617-2018(10617)	-	30000	-
Cl. 10 of IS:10617-2018(10617)	-	15000	-
Cl. 11, 11.1, 11.2, 11.2.1 of IS:10617-2018(10617)	-	10000	-
6.1.2(Startability Test)	-	100000	-
8(Locked Rotor Test)	-	280000	-
6.1.4 & 6.3 (a)(High Voltage Test)	-	30000	-
6.3 (c )(Pneumatic test of shell)	-	30000	-
6.1.7(Bursting Test)	-	50000	-
Cl. 6.2 of IS:10617:2018(10617)	-	35000	-
6.3(b)(Insulation resistance test)	-	20000	-
7(Running Overload test)	-	150000	-
9(Resistance to rusting ANNEX B)	-	30000	-
11(Marking)	-	2000	-
Cl. 6.1.2.3 of IS:10617:2018(10617)	-	100000	-
Cl. 6.1.2.4 of IS:10617:2018(10617)	-	100000	-

14 Nov, 2027

-
-

IS 14203 (2023)

FIRE RESISTING RECORD PROTECTION CABINETS SPECIFICATION Second Revision of IS 14203

198000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 and 6 (Table 1)(Nominal Sizes - Height)	-	20000	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	20000	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	20000	-
3 and 6 (Table 1)(Height of Pedestal)	-	20000	-
7(Designation)	-	20000	-
8.1(Cabinet Construction)	-	20000	-
8.2(Locking Mechanism)	-	100000	-
8.3(Locks)	-	20000	-
8.4(Handles)	-	20000	-
9(Internal Fixtures)	-	20000	-
10.1(Minimum overall thinckness of coating)	-	20000	-
10.2(Cross Hatch Test)	-	20000	-
11, Annex-B, 3.1(Fire Endurance Test)	-	120000	-
11, Annex-B, 3.2(Fire and Impact test)	-	100000	-
3 and 6 (Table 1)(Nominal Sizes - Height)	-	20000	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	20000	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	20000	-
3 and 6 (Table 1)(Height of Pedestal)	-	20000	-
7(Designation)	-	20000	-
8.1(Cabinet Construction)	-	20000	-
8.2(Locking Mechanism)	-	20000	-
8.3(Locks)	-	20000	-
8.4(Handles)	-	20000	-
9(Internal Fixtures)	-	20000	-
10.1(Minimum overall thinckness of coating)	-	20000	-
10.2(Cross Hatch Test)	-	20000	-
11, Annex-B, 3.1(Fire Endurance Test)	-	120000	-
11, Annex-B, 3.2(Fire and Impact test)	-	100000	-

14 Nov, 2027

-
-

IS 14561 (2014)

Fire resisting (Insulating) filing cabinets - Specification (Second Revision)

258000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Types & Rating)	-	5000	-
3.1(i) The fire resisting filing cabinets shall be of two types: a) Vertical fire resisting filing cabinet, and b) Lateral fire resisting filing cabinet.)	-	5000	-
3.2(ii) The standard and lateral fire resisting filing cabinets shall have one-drawer or two-drawers or three drawers or four-drawers. A typical drawing of the fire resisting filing cabinet is given in Fig. 1.)	-	5000	-
3.3(iii) The fire resisting filing cabinets shall have fire resisting ratings of 60 min or 120 min or 180 min or 240 min)	-	5000	-
4(Dimensions and Tolerances, mm)	-	5000	-
4.1(Overall Dimensions of Fire Resisting Filing Cabinets: The internal usable space of the drawers of fire resisting (insulating) filing cabinets shall be as specified in Table 1 or any other size which is mutually agreed to between the purchaser and the supplier.)	-	5000	-
4.1(Internal usuable space of drawer, mm:)	-	5000	-
4.1(i) Height)	-	5000	-
4.1(ii) Width)	-	5000	-
4.1(iii) Depth)	-	5000	-
4.1(iv) Height of the bottom drawer above floor level)	-	5000	-
5(Materials)	-	5000	-
6(Designations: The filing cabinet shall be designated by the commonly used name, type, the fire rating and the number of this Indian Standard.)	-	5000	-
7(Constructions)	-	15000	-
7.1(Outer body and Inner Box: Outer body and inner box shall be fabricated from mild steel or galvanized steel sheets of not less than 0.8 mm and not more than 1.2 mm nominal thickness. The steel shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-	5000	-
7.2(Cabinets Sub-Assembly: The external body and drawer fronts of the fire resisting (insulating) filing cabinet shall be of double wall type with homogeneous insulating material filled in between. Further the construction of the cabinet shall be such that each drawer slides in an individual inner box. The inner boxes shall have a insulating layer between each other to prevent fire spreading from one drawer to another. The joining of inner box, intermediate piece and outer body shall be such that, it forms a cavity to receive drawer front )	-	5000	-
7.3(Filing Drawer: The drawer shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall have an arrangement on the sides suitable for the drawer suspension system and an arrangement to stop it when fully pushed in.)	-	5000	-
7.3.1(Drawer Front: The drawer front shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall be firmly secured to the drawer body by welding, screwing or riveting or any combination of these processes. The construction of drawer front shall be such that it snugly fits in the cavity provided for the same )	-	5000	-
7.4.1(Latch: Each drawer of the cabinet shall be removable but shall be fitted with a latch/positive stop to prevent inadvertent withdrawal and rebound. Such latch shall be lifted/unlocked by the pull of the handle or any other mechanism.)	-	5000	-
7.4.2(The locking mechanism shall be designed in such a manner so that there is minimum passage for direct conduction of heat from outside to inside)	-	5000	-
7.5(Drawer Suspension The drawer suspension shall be either of the following types to ensure withdrawal of the full depth of the drawer: a) Ball bearing / Roller bearing suspension (Movement), b) Solid roller suspension, and c) Telescopic slide suspension (Extension)	-	5000	-
7.6(Handles: Each drawer shall be provided either with a handle made from ferrous/non-ferrous material suitably coated for corrosion resistance, or any polymer and fixed to the front of the drawer or with a built in pulling mechanism)	-	5000	-
7.6.1(The drawer handle shall be strong enough to take a minimum pull of 50 N for 2 min. There shall be no sharp corners or edges to avoid injury and damage to clothing)	-	5000	-
7.7.1(Locks: Top drawer shall be provided with single or dual control key lock having not less than 6 levers or pin cylinder lock having not less than 6 pins, with duplicate keys of stainless steel/nonferrous alloy. Alternatively if required by the purchaser a 3 wheel combination lock or electronic combination lock may be provided either in place of key lock or in addition to key lock)	-	5000	-
7.7.2(Each drawer may also be provided with individual key lock or pin cylinder lock or combination lock subject to agreement between the purchaser and the supplier.)	-	5000	-
7.8(Locking Mechanism )	-	5000	-
7.8.1(The locking mechanism shall be such that when the top drawer is pushed-in fully, it actuates locking mechanism to lock all other drawers imultaneously, when they are in pushed-in position)	-	5000	-
7.8.1.1(At the time of locking the cabinet, if one of the drawers is not fully pushed-in, that drawer shall remain unlocked and can be used. As soon as that drawer is pushed-in fully, it shall get locked automatically without further operation of key by the user.)	-	5000	-
7.8.1.2(In addition to the above, isolation mechanism shall also be provided to permit independent locking/ use of other drawers. Such isolation mechanism provided on drawers shall be manually operated)	-	5000	-
8(Assemblies)	-	5000	-
8.1(The components shall be assembled by bolting, welding, riveting or by any combination of these processes)	-	5000	-
8.2(All joints between outer body and inner boxes, the drawer front and the outer body shall be such that, there is minimum direct conduction of heat from outer body to inner body)	-	5000	-
9.1(Drawer Suspension Test and Latch Test: The drawer loaded with evenly distributed load of 30 kg (excluding the weight of drawer) in any drawer shall be operated for 5 000 cycles at a rate of 300 cycles/h ±10 percent. One opening and one closing shall constitute one cycle. The test shall be carried out with maximum two breaks by using electrically or mechanically operated test equipment with a counter fitted on it. After 5 000 cycles the suspension slide and latch mechanism shall not show any apparent distortion, cracks, or failures to operate in a normal smooth manner)	-	5000	-
10.1(Finish: All dents, burrs and sharp edges shall be removed from the various components and they shall be thoroughly degreased and cleaned of rust and scale)	-	5000	-
10.2(The inside and outside surfaces of the fire resisting (Insulating) filing cabinet shall be painted or powder coated. In case of paint, an appropriate primer and undercoating shall be used in accordance to industry practices. The minimum overall thickness of the coatings shall be 50 μ for powder coating and 70 μ for liquid paint. Cross hatch test shall be conducted to confirm the adhesion of coating in accordance with 10.2.1)	-	5000	-
10.2.1(Cross Hatch Test)	-	5000	-
10.2.1(a) Make 6 parallel cut marks using sharp metal pointer and straight edge, through the painted/ coated surface, so as to make the base surface visible through cut marks)	-	5000	-
10.2.1(b) Cut marks shall be minimum 20 mm long and at 2 mm distance from each other)	-	5000	-
10.2.1(c) Make 6 similar cut marks in the direction perpendicular to first set of cut marks, with same length and spacing)	-	5000	-
10.2.1(d) These 12 cut marks together shall make a pattern of 25 squares of 2 mm × 2mm size, totally separated from each other)	-	5000	-
10.2.1(f) To ensure continuous contact with paint/coat film, rub the tape firmly and remove air bubbles under the tape, if any)	-	5000	-
10.2.1(g)Within 60 to 120 s after sticking the tape, remove it by seizing free end of the tape and rapidly pulling it off at an angle close to 180°.)	-	5000	-
10.2.1(h) Painting/Coating quality is considered as acceptable, if no part of any 2 mm × 2 mm square of paint/coat comes off the surface due to pulling the tape)	-	5000	-
11.1(Fire endurance test)	-	5000	-
11.2(Fire and impact test)	-	5000	-
12.1(Marking of Cabinets:A metal plate showing classification of cabinet together with the manufacturer’s name, serial number and the year of manufacture shall be fixed inside surface of the top drawer of the cabinet in such a way that it is visible when it is opened.)	-	5000	-
12.2(Marking on Keys: The keys shall bear an identification number which shall not be the same as the serial number of the cabinet)	-	5000	-
3(Types & Rating)	-	5000	-
3.1(i) The fire resisting filing cabinets shall be of two types: a) Vertical fire resisting filing cabinet, and b) Lateral fire resisting filing cabinet.)	-	5000	-
3.2(ii) The standard and lateral fire resisting filing cabinets shall have one-drawer or two-drawers or three drawers or four-drawers. A typical drawing of the fire resisting filing cabinet is given in Fig. 1.)	-	5000	-
3.3(iii) The fire resisting filing cabinets shall have fire resisting ratings of 60 min or 120 min or 180 min or 240 min)	-	5000	-
4(Dimensions and Tolerances, mm)	-	5000	-
4.1(Overall Dimensions of Fire Resisting Filing Cabinets: The internal usable space of the drawers of fire resisting (insulating) filing cabinets shall be as specified in Table 1 or any other size which is mutually agreed to between the purchaser and the supplier.)	-	5000	-
4.1(Internal usuable space of drawer, mm:)	-	5000	-
4.1(i) Height)	-	5000	-
4.1(ii) Width)	-	5000	-
4.1(iii) Depth)	-	5000	-
4.1(iv) Height of the bottom drawer above floor level)	-	5000	-
5(Materials)	-	5000	-
6(Designations: The filing cabinet shall be designated by the commonly used name, type, the fire rating and the number of this Indian Standard.)	-	5000	-
7(Constructions)	-	5000	-
7.1(Outer body and Inner Box: Outer body and inner box shall be fabricated from mild steel or galvanized steel sheets of not less than 0.8 mm and not more than 1.2 mm nominal thickness. The steel shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-	5000	-
7.2(Cabinets Sub-Assembly: The external body and drawer fronts of the fire resisting (insulating) filing cabinet shall be of double wall type with homogeneous insulating material filled in between. Further the construction of the cabinet shall be such that each drawer slides in an individual inner box. The inner boxes shall have a insulating layer between each other to prevent fire spreading from one drawer to another. The joining of inner box, intermediate piece and outer body shall be such that, it forms a cavity to receive drawer front )	-	5000	-
7.3(Filing Drawer: The drawer shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall have an arrangement on the sides suitable for the drawer suspension system and an arrangement to stop it when fully pushed in.)	-	5000	-
7.3.1(Drawer Front: The drawer front shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall be firmly secured to the drawer body by welding, screwing or riveting or any combination of these processes. The construction of drawer front shall be such that it snugly fits in the cavity provided for the same )	-	5000	-
7.4.1(Latch: Each drawer of the cabinet shall be removable but shall be fitted with a latch/positive stop to prevent inadvertent withdrawal and rebound. Such latch shall be lifted/unlocked by the pull of the handle or any other mechanism.)	-	5000	-
7.4.2(The locking mechanism shall be designed in such a manner so that there is minimum passage for direct conduction of heat from outside to inside)	-	5000	-
7.5(Drawer Suspension The drawer suspension shall be either of the following types to ensure withdrawal of the full depth of the drawer: a) Ball bearing / Roller bearing suspension (Movement), b) Solid roller suspension, and c) Telescopic slide suspension (Extension)	-	5000	-
7.6(Handles: Each drawer shall be provided either with a handle made from ferrous/non-ferrous material suitably coated for corrosion resistance, or any polymer and fixed to the front of the drawer or with a built in pulling mechanism)	-	5000	-
7.6.1(The drawer handle shall be strong enough to take a minimum pull of 50 N for 2 min. There shall be no sharp corners or edges to avoid injury and damage to clothing)	-	5000	-
7.7.1(Locks: Top drawer shall be provided with single or dual control key lock having not less than 6 levers or pin cylinder lock having not less than 6 pins, with duplicate keys of stainless steel/nonferrous alloy. Alternatively if required by the purchaser a 3 wheel combination lock or electronic combination lock may be provided either in place of key lock or in addition to key lock)	-	5000	-
7.7.2(Each drawer may also be provided with individual key lock or pin cylinder lock or combination lock subject to agreement between the purchaser and the supplier.)	-	5000	-
7.8(Locking Mechanism )	-	5000	-
7.8.1(The locking mechanism shall be such that when the top drawer is pushed-in fully, it actuates locking mechanism to lock all other drawers imultaneously, when they are in pushed-in position)	-	5000	-
7.8.1.1(At the time of locking the cabinet, if one of the drawers is not fully pushed-in, that drawer shall remain unlocked and can be used. As soon as that drawer is pushed-in fully, it shall get locked automatically without further operation of key by the user.)	-	5000	-
7.8.1.2(In addition to the above, isolation mechanism shall also be provided to permit independent locking/ use of other drawers. Such isolation mechanism provided on drawers shall be manually operated)	-	5000	-
8(Assemblies)	-	5000	-
8.1(The components shall be assembled by bolting, welding, riveting or by any combination of these processes)	-	5000	-
8.2(All joints between outer body and inner boxes, the drawer front and the outer body shall be such that, there is minimum direct conduction of heat from outer body to inner body)	-	5000	-
9.1(Drawer Suspension Test and Latch Test: The drawer loaded with evenly distributed load of 30 kg (excluding the weight of drawer) in any drawer shall be operated for 5 000 cycles at a rate of 300 cycles/h ±10 percent. One opening and one closing shall constitute one cycle. The test shall be carried out with maximum two breaks by using electrically or mechanically operated test equipment with a counter fitted on it. After 5 000 cycles the suspension slide and latch mechanism shall not show any apparent distortion, cracks, or failures to operate in a normal smooth manner)	-	5000	-
10.1(Finish: All dents, burrs and sharp edges shall be removed from the various components and they shall be thoroughly degreased and cleaned of rust and scale)	-	5000	-
10.2(The inside and outside surfaces of the fire resisting (Insulating) filing cabinet shall be painted or powder coated. In case of paint, an appropriate primer and undercoating shall be used in accordance to industry practices. The minimum overall thickness of the coatings shall be 50 μ for powder coating and 70 μ for liquid paint. Cross hatch test shall be conducted to confirm the adhesion of coating in accordance with 10.2.1)	-	5000	-
10.2.1(Cross Hatch Test)	-	5000	-
10.2.1(a) Make 6 parallel cut marks using sharp metal pointer and straight edge, through the painted/ coated surface, so as to make the base surface visible through cut marks)	-	5000	-
10.2.1(b) Cut marks shall be minimum 20 mm long and at 2 mm distance from each other)	-	5000	-
10.2.1(c) Make 6 similar cut marks in the direction perpendicular to first set of cut marks, with same length and spacing)	-	5000	-
10.2.1(d) These 12 cut marks together shall make a pattern of 25 squares of 2 mm × 2mm size, totally separated from each other)	-	5000	-
10.2.1(f) To ensure continuous contact with paint/coat film, rub the tape firmly and remove air bubbles under the tape, if any)	-	5000	-
10.2.1(g)Within 60 to 120 s after sticking the tape, remove it by seizing free end of the tape and rapidly pulling it off at an angle close to 180°.)	-	5000	-
10.2.1(h) Painting/Coating quality is considered as acceptable, if no part of any 2 mm × 2 mm square of paint/coat comes off the surface due to pulling the tape)	-	5000	-
11.1(Fire endurance test)	-	150000	-
11.2(Fire and impact test)	-	150000	-
12.1(Marking of Cabinets:A metal plate showing classification of cabinet together with the manufacturer’s name, serial number and the year of manufacture shall be fixed inside surface of the top drawer of the cabinet in such a way that it is visible when it is opened.)	-	15000	-
12.2(Marking on Keys: The keys shall bear an identification number which shall not be the same as the serial number of the cabinet)	-	15000	-
3(Types & Rating)	-	15000	-
3.1(i) The fire resisting filing cabinets shall be of two types: a) Vertical fire resisting filing cabinet, and b) Lateral fire resisting filing cabinet.)	-	15000	-
3.2(ii) The standard and lateral fire resisting filing cabinets shall have one-drawer or two-drawers or three drawers or four-drawers. A typical drawing of the fire resisting filing cabinet is given in Fig. 1.)	-	15000	-
3.3(iii) The fire resisting filing cabinets shall have fire resisting ratings of 60 min or 120 min or 180 min or 240 min)	-	15000	-
4(Dimensions and Tolerances, mm)	-	15000	-
4.1(Overall Dimensions of Fire Resisting Filing Cabinets: The internal usable space of the drawers of fire resisting (insulating) filing cabinets shall be as specified in Table 1 or any other size which is mutually agreed to between the purchaser and the supplier.)	-	15000	-
4.1(Internal usuable space of drawer, mm:)	-	15000	-
4.1(i) Height)	-	15000	-
4.1(ii) Width)	-	15000	-
4.1(iii) Depth)	-	15000	-
4.1(iv) Height of the bottom drawer above floor level)	-	15000	-
5(Materials)	-	15000	-
6(Designations: The filing cabinet shall be designated by the commonly used name, type, the fire rating and the number of this Indian Standard.)	-	15000	-
7(Constructions)	-	15000	-
7.1(Outer body and Inner Box: Outer body and inner box shall be fabricated from mild steel or galvanized steel sheets of not less than 0.8 mm and not more than 1.2 mm nominal thickness. The steel shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-	15000	-
7.2(Cabinets Sub-Assembly: The external body and drawer fronts of the fire resisting (insulating) filing cabinet shall be of double wall type with homogeneous insulating material filled in between. Further the construction of the cabinet shall be such that each drawer slides in an individual inner box. The inner boxes shall have a insulating layer between each other to prevent fire spreading from one drawer to another. The joining of inner box, intermediate piece and outer body shall be such that, it forms a cavity to receive drawer front )	-	15000	-
7.3(Filing Drawer: The drawer shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall have an arrangement on the sides suitable for the drawer suspension system and an arrangement to stop it when fully pushed in.)	-	15000	-
7.3.1(Drawer Front: The drawer front shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall be firmly secured to the drawer body by welding, screwing or riveting or any combination of these processes. The construction of drawer front shall be such that it snugly fits in the cavity provided for the same )	-	15000	-
7.4.1(Latch: Each drawer of the cabinet shall be removable but shall be fitted with a latch/positive stop to prevent inadvertent withdrawal and rebound. Such latch shall be lifted/unlocked by the pull of the handle or any other mechanism.)	-	15000	-
7.4.2(The locking mechanism shall be designed in such a manner so that there is minimum passage for direct conduction of heat from outside to inside)	-	15000	-
7.5(Drawer Suspension The drawer suspension shall be either of the following types to ensure withdrawal of the full depth of the drawer: a) Ball bearing / Roller bearing suspension (Movement), b) Solid roller suspension, and c) Telescopic slide suspension (Extension)	-	15000	-
7.6(Handles: Each drawer shall be provided either with a handle made from ferrous/non-ferrous material suitably coated for corrosion resistance, or any polymer and fixed to the front of the drawer or with a built in pulling mechanism)	-	15000	-
7.6.1(The drawer handle shall be strong enough to take a minimum pull of 50 N for 2 min. There shall be no sharp corners or edges to avoid injury and damage to clothing)	-	15000	-
7.7.1(Locks: Top drawer shall be provided with single or dual control key lock having not less than 6 levers or pin cylinder lock having not less than 6 pins, with duplicate keys of stainless steel/nonferrous alloy. Alternatively if required by the purchaser a 3 wheel combination lock or electronic combination lock may be provided either in place of key lock or in addition to key lock)	-	15000	-
7.7.2(Each drawer may also be provided with individual key lock or pin cylinder lock or combination lock subject to agreement between the purchaser and the supplier.)	-	15000	-
7.8(Locking Mechanism )	-	15000	-
7.8.1(The locking mechanism shall be such that when the top drawer is pushed-in fully, it actuates locking mechanism to lock all other drawers imultaneously, when they are in pushed-in position)	-	15000	-
7.8.1.1(At the time of locking the cabinet, if one of the drawers is not fully pushed-in, that drawer shall remain unlocked and can be used. As soon as that drawer is pushed-in fully, it shall get locked automatically without further operation of key by the user.)	-	15000	-
7.8.1.2(In addition to the above, isolation mechanism shall also be provided to permit independent locking/ use of other drawers. Such isolation mechanism provided on drawers shall be manually operated)	-	15000	-
8(Assemblies)	-	15000	-
8.1(The components shall be assembled by bolting, welding, riveting or by any combination of these processes)	-	15000	-
8.2(All joints between outer body and inner boxes, the drawer front and the outer body shall be such that, there is minimum direct conduction of heat from outer body to inner body)	-	15000	-
9.1(Drawer Suspension Test and Latch Test: The drawer loaded with evenly distributed load of 30 kg (excluding the weight of drawer) in any drawer shall be operated for 5 000 cycles at a rate of 300 cycles/h ±10 percent. One opening and one closing shall constitute one cycle. The test shall be carried out with maximum two breaks by using electrically or mechanically operated test equipment with a counter fitted on it. After 5 000 cycles the suspension slide and latch mechanism shall not show any apparent distortion, cracks, or failures to operate in a normal smooth manner)	-	15000	-
10.1(Finish: All dents, burrs and sharp edges shall be removed from the various components and they shall be thoroughly degreased and cleaned of rust and scale)	-	15000	-
10.2(The inside and outside surfaces of the fire resisting (Insulating) filing cabinet shall be painted or powder coated. In case of paint, an appropriate primer and undercoating shall be used in accordance to industry practices. The minimum overall thickness of the coatings shall be 50 μ for powder coating and 70 μ for liquid paint. Cross hatch test shall be conducted to confirm the adhesion of coating in accordance with 10.2.1)	-	15000	-
10.2.1(Cross Hatch Test)	-	15000	-
10.2.1(a) Make 6 parallel cut marks using sharp metal pointer and straight edge, through the painted/ coated surface, so as to make the base surface visible through cut marks)	-	15000	-
10.2.1(b) Cut marks shall be minimum 20 mm long and at 2 mm distance from each other)	-	15000	-
10.2.1(c) Make 6 similar cut marks in the direction perpendicular to first set of cut marks, with same length and spacing)	-	15000	-
10.2.1(d) These 12 cut marks together shall make a pattern of 25 squares of 2 mm × 2mm size, totally separated from each other)	-	15000	-
10.2.1(f) To ensure continuous contact with paint/coat film, rub the tape firmly and remove air bubbles under the tape, if any)	-	15000	-
10.2.1(g)Within 60 to 120 s after sticking the tape, remove it by seizing free end of the tape and rapidly pulling it off at an angle close to 180°.)	-	15000	-
10.2.1(h) Painting/Coating quality is considered as acceptable, if no part of any 2 mm × 2 mm square of paint/coat comes off the surface due to pulling the tape)	-	15000	-
11.1(Fire endurance test)	-	15000	-
11.2(Fire and impact test)	-	15000	-
12.1(Marking of Cabinets:A metal plate showing classification of cabinet together with the manufacturer’s name, serial number and the year of manufacture shall be fixed inside surface of the top drawer of the cabinet in such a way that it is visible when it is opened.)	-	15000	-
12.2(Marking on Keys: The keys shall bear an identification number which shall not be the same as the serial number of the cabinet)	-	15000	-
3(Types & Rating)	-	15000	-
3.1(i) The fire resisting filing cabinets shall be of two types: a) Vertical fire resisting filing cabinet, and b) Lateral fire resisting filing cabinet.)	-	15000	-
3.2(ii) The standard and lateral fire resisting filing cabinets shall have one-drawer or two-drawers or three drawers or four-drawers. A typical drawing of the fire resisting filing cabinet is given in Fig. 1.)	-	15000	-
3.3(iii) The fire resisting filing cabinets shall have fire resisting ratings of 60 min or 120 min or 180 min or 240 min)	-	15000	-
4(Dimensions and Tolerances, mm)	-	15000	-
4.1(Overall Dimensions of Fire Resisting Filing Cabinets: The internal usable space of the drawers of fire resisting (insulating) filing cabinets shall be as specified in Table 1 or any other size which is mutually agreed to between the purchaser and the supplier.)	-	15000	-
4.1(Internal usuable space of drawer, mm:)	-	15000	-
4.1(i) Height)	-	15000	-
4.1(ii) Width)	-	15000	-
4.1(iii) Depth)	-	15000	-
4.1(iv) Height of the bottom drawer above floor level)	-	15000	-
5(Materials)	-	15000	-
6(Designations: The filing cabinet shall be designated by the commonly used name, type, the fire rating and the number of this Indian Standard.)	-	15000	-
7(Constructions)	-	15000	-
7.1(Outer body and Inner Box: Outer body and inner box shall be fabricated from mild steel or galvanized steel sheets of not less than 0.8 mm and not more than 1.2 mm nominal thickness. The steel shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-	15000	-
7.2(Cabinets Sub-Assembly: The external body and drawer fronts of the fire resisting (insulating) filing cabinet shall be of double wall type with homogeneous insulating material filled in between. Further the construction of the cabinet shall be such that each drawer slides in an individual inner box. The inner boxes shall have a insulating layer between each other to prevent fire spreading from one drawer to another. The joining of inner box, intermediate piece and outer body shall be such that, it forms a cavity to receive drawer front )	-	15000	-
7.3(Filing Drawer: The drawer shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall have an arrangement on the sides suitable for the drawer suspension system and an arrangement to stop it when fully pushed in.)	-	15000	-
7.3.1(Drawer Front: The drawer front shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall be firmly secured to the drawer body by welding, screwing or riveting or any combination of these processes. The construction of drawer front shall be such that it snugly fits in the cavity provided for the same )	-	15000	-
7.4.1(Latch: Each drawer of the cabinet shall be removable but shall be fitted with a latch/positive stop to prevent inadvertent withdrawal and rebound. Such latch shall be lifted/unlocked by the pull of the handle or any other mechanism.)	-	15000	-
7.4.2(The locking mechanism shall be designed in such a manner so that there is minimum passage for direct conduction of heat from outside to inside)	-	15000	-
7.5(Drawer Suspension The drawer suspension shall be either of the following types to ensure withdrawal of the full depth of the drawer: a) Ball bearing / Roller bearing suspension (Movement), b) Solid roller suspension, and c) Telescopic slide suspension (Extension)	-	15000	-
7.6(Handles: Each drawer shall be provided either with a handle made from ferrous/non-ferrous material suitably coated for corrosion resistance, or any polymer and fixed to the front of the drawer or with a built in pulling mechanism)	-	15000	-
7.6.1(The drawer handle shall be strong enough to take a minimum pull of 50 N for 2 min. There shall be no sharp corners or edges to avoid injury and damage to clothing)	-	15000	-
7.7.1(Locks: Top drawer shall be provided with single or dual control key lock having not less than 6 levers or pin cylinder lock having not less than 6 pins, with duplicate keys of stainless steel/nonferrous alloy. Alternatively if required by the purchaser a 3 wheel combination lock or electronic combination lock may be provided either in place of key lock or in addition to key lock)	-	15000	-
7.7.2(Each drawer may also be provided with individual key lock or pin cylinder lock or combination lock subject to agreement between the purchaser and the supplier.)	-	15000	-
7.8(Locking Mechanism )	-	15000	-
7.8.1(The locking mechanism shall be such that when the top drawer is pushed-in fully, it actuates locking mechanism to lock all other drawers imultaneously, when they are in pushed-in position)	-	15000	-
7.8.1.1(At the time of locking the cabinet, if one of the drawers is not fully pushed-in, that drawer shall remain unlocked and can be used. As soon as that drawer is pushed-in fully, it shall get locked automatically without further operation of key by the user.)	-	15000	-
7.8.1.2(In addition to the above, isolation mechanism shall also be provided to permit independent locking/ use of other drawers. Such isolation mechanism provided on drawers shall be manually operated)	-	15000	-
8(Assemblies)	-	15000	-
8.1(The components shall be assembled by bolting, welding, riveting or by any combination of these processes)	-	15000	-
8.2(All joints between outer body and inner boxes, the drawer front and the outer body shall be such that, there is minimum direct conduction of heat from outer body to inner body)	-	15000	-
9.1(Drawer Suspension Test and Latch Test: The drawer loaded with evenly distributed load of 30 kg (excluding the weight of drawer) in any drawer shall be operated for 5 000 cycles at a rate of 300 cycles/h ±10 percent. One opening and one closing shall constitute one cycle. The test shall be carried out with maximum two breaks by using electrically or mechanically operated test equipment with a counter fitted on it. After 5 000 cycles the suspension slide and latch mechanism shall not show any apparent distortion, cracks, or failures to operate in a normal smooth manner)	-	15000	-
10.1(Finish: All dents, burrs and sharp edges shall be removed from the various components and they shall be thoroughly degreased and cleaned of rust and scale)	-	15000	-
10.2(The inside and outside surfaces of the fire resisting (Insulating) filing cabinet shall be painted or powder coated. In case of paint, an appropriate primer and undercoating shall be used in accordance to industry practices. The minimum overall thickness of the coatings shall be 50 μ for powder coating and 70 μ for liquid paint. Cross hatch test shall be conducted to confirm the adhesion of coating in accordance with 10.2.1)	-	15000	-
10.2.1(Cross Hatch Test)	-	15000	-
10.2.1(a) Make 6 parallel cut marks using sharp metal pointer and straight edge, through the painted/ coated surface, so as to make the base surface visible through cut marks)	-	15000	-
10.2.1(b) Cut marks shall be minimum 20 mm long and at 2 mm distance from each other)	-	15000	-
10.2.1(c) Make 6 similar cut marks in the direction perpendicular to first set of cut marks, with same length and spacing)	-	15000	-
10.2.1(d) These 12 cut marks together shall make a pattern of 25 squares of 2 mm × 2mm size, totally separated from each other)	-	15000	-
10.2.1(f) To ensure continuous contact with paint/coat film, rub the tape firmly and remove air bubbles under the tape, if any)	-	15000	-
10.2.1(g)Within 60 to 120 s after sticking the tape, remove it by seizing free end of the tape and rapidly pulling it off at an angle close to 180°.)	-	15000	-
10.2.1(h) Painting/Coating quality is considered as acceptable, if no part of any 2 mm × 2 mm square of paint/coat comes off the surface due to pulling the tape)	-	15000	-
11.1(Fire endurance test)	-	150000	-
11.2(Fire and impact test)	-	150000	-
12.1(Marking of Cabinets:A metal plate showing classification of cabinet together with the manufacturer’s name, serial number and the year of manufacture shall be fixed inside surface of the top drawer of the cabinet in such a way that it is visible when it is opened.)	-	5000	-
12.2(Marking on Keys: The keys shall bear an identification number which shall not be the same as the serial number of the cabinet)	-	5000	-

14 Nov, 2027

-
Included w.e.f. 28.03.2025

IS 11188 : Part 1 (2021)

Vault Strong Room doors Part 1 specification

298000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1 (3)(Fire and stream hose IS 11188 (Part 3))	-	15000	-
11.1 (2)(Fire endurance IS 11188 (Part 3))	-	150000	-
11.1 (1)(Burglary resistance IS 11188 (Part 2))	-	150000	-
10.4(Alternate to Cl 10.4)	-	15000	-
10.3(Cross Hatch Test)	-	15000	-
10(FINISH)	-	15000	-
9.4(Vault Lighting Control)	-	15000	-
9.3(Foot Bridge)	-	15000	-
9.2(Handles)	-	15000	-
9.1.1(Adjusting Bolt)	-	15000	-
9.1(Hinges)	-	15000	-
9(DOOR FITTINGS)	-	15000	-
8.4.5(Automatic Relocking Device)	-	15000	-
8.4.4(Time Lock)	-	15000	-
8.4(Lock)	-	15000	-
8.3.2.2(Construction)	-	15000	-
8.3.2.1(The number of bolts and their minimum dimension)	-	15000	-
8.3.2(Bolt Work)	-	15000	-
8.3.1(Lock Case)	-	15000	-
8.3(Locking Mechanism)	-	15000	-
8.2.3(Crane Hinge Mechanism)	-	15000	-
8.2.2(Compression Mechanism)	-	15000	-
8.2.1(Rebate of the Door Frame)	-	15000	-
8.2(Doors Frame)	-	15000	-
8.1.2(Main Door (Outside))	-	15000	-
8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1 Fig. 1(Doors)	-	15000	-
8(CONSTRUCTION AND GENERALREQUIREMENTS)	-	15000	-
5 Table 1(bolts, Min)	-	15000	-
5 Table 1(xix) Depth of engagement of shooting)	-	15000	-
5 Table 1(cross sectional area, Min,sq mm)	-	15000	-
5 Table 1(xviii) Diameter of shooting bolts, Min)	-	15000	-
5 Table 1(xvi) Number of shooting bolts at top,Min)	-	15000	-
5 Table 1(xv) Number of shooting bolts on opposite side,Min)	-	15000	-
5 Table 1(xiv) Number of shooting bolts on hinge side, Min)	-	15000	-
5 Table 1(xiii) Number of locks)	-	15000	-
5 Table 1(xii) Wall thickness (recommendation))	-	15000	-
5 Table 1(xi) Thickness of drill and oxyacetylene torch resisting layer (excluding mild steel plates),Min)	-	15000	-
5 Table 1(ix) Thickness of doors slab, thickness over rebate)	-	15000	-
5 Table 1(viii) Pitch of grill gate rods)	-	15000	-
5 Table 1(vii) Diameter of grill gate rods, Min)	-	15000	-
5 Table 1(vi) Thickens of grill gate angles or section made out of M.S. plates, Min)	-	15000	-
5 Table 1(v) Dimension of the rebate coming under shear)	-	15000	-
5 Table 1(iv (b) Thickness of door frame, if fabricated from single plate to form channel/multi-bend section, Min)	-	15000	-
5 Table 1(ii (a) Height H, Min b) Width W, Min iv(a) Thickness of door frame angle, channel or section made out of M.S. plates, if built up to form a channel,Min)	-	15000	-
5 Table 1(iii) Inside dimension or clear opening when door shutters are swung open at 180 degree)	-	15000	-
5 Table 1(ii (b) Width W)	-	15000	-
5 Table 1(ii (a) Height, H)	-	15000	-
5 Table 1(ii) Overall dimension of vault door)	-	15000	-
5 Table 1(i) Door Type)	-	15000	-
4(Type)	-	15000	-
5(Table-1)(Type of Door)	-	15000	-
5(Table-1)(Overall dimesion of door)	-	15000	-
5(Table-1)(Inside dimension or clear opening of door)	-	15000	-
5(Table-1)(Thickness of door frame angle-made of Plate,if bulit up to form a channel)	-	15000	-
5(Table-1)(Thickness of door frame ,if fabricated or multibend)	-	15000	-
5(Table-1)(Dimension of the rebate coming under share)	-	15000	-
5(Table-1)(Thickness of grill gate angle/section)	-	15000	-
5(Table-1)(Diameter of grill gate rod)	-	15000	-
5(Table-1)(Pitch of grill gate rod)	-	15000	-
5(Table-1)(Thickness of door slab,thickness over rebate)	-	15000	-
5(Table-1)(Thickness of the door over lock)	-	15000	-
5(Table-1)(Thickness of drill & oxyacetylene torch resis. layer(exclue MS plate)	-	15000	-
5(Table-1)(Wall thickness)	-	15000	-
5(Table-1)(Number of locks)	-	15000	-
5(Table-1)(Number of shooting bolys on hinge side)	-	15000	-
5(Table-1)(Number of shooting bolts on opposite)	-	15000	-
5(Table-1)(Number of shooting bolts at top)	-	15000	-
5(Table-1)(Number of shooting bolts at bottom)	-	15000	-
5(Table-1)(Cross sectional area as per shooting bolt)	-	15000	-
5(Table-1)(Depth engagement of shooting)	-	15000	-
6(Materail)	-	15000	-
7(Classification)	-	15000	-
8 & 8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1.1.1(Locking device (unpickable dual control lock))	-	15000	-
8.1.2(Main Door- Outer & inner plate thickness)	-	15000	-
8.1.2.1(Door(Finish &Gap of frame/edge with any place))	-	15000	-
8.2(Door frame (No.of barckets & Size for gripping))	-	15000	-
8.2.1(Rebate of the door frame)	-	15000	-
8.2.2(Compression mechanism)	-	15000	-
8.2.3(Crane hinge mechanism)	-	15000	-
8.3(Lock case)	-	15000	-
8.3.2(Bolt work)	-	15000	-
8.3.2.2(Construction (of bolt work))	-	15000	-
8.3.2.3(Bearing piller)	-	15000	-
8.4.1(Shooting bolt control (By lock))	-	15000	-
8.4.2(Test of key-Lock)	-	15000	-
8.4.3(Lock fixing bolts)	-	15000	-
8.4.4(Time lock)	-	15000	-
8.4.5(Automatic Relocking devise)	-	15000	-
9 &9.1(Hinges)	-	15000	-
9.1.1(Adjusting bolt)	-	15000	-
9.2(Handles)	-	15000	-
9.3(Foot bringe)	-	15000	-
9.4(Vault lighting control)	-	15000	-
10 &10.1(Dents,Burrs & Edges)	-	15000	-
10.2(Colour coating thickness (Surafce paint))	-	15000	-
10.3(Cross Hatch test)	-	15000	-
10.4(Door (Stainless cladding))	-	15000	-
11.1 &11.2(Test criteria for confomity -Burglaty attack)	-	15000	-
11.1 &11.2(Test criteria for confomity -Fire resistancey)	-	15000	-
12(Marking of door)	-	15000	-
12.2(Marking on keys)	-	15000	-
4(Type)	-	15000	-
5(Table-1)(5(Table-1))	-	15000	-
5(Table-1)(Overall dimesion of door)	-	15000	-
5(Table-1)(Inside dimension or clear opening of door)	-	15000	-
5(Table-1)(Thickness of door frame angle-made of Plate,if bulit up to form a channel)	-	15000	-
5(Table-1)(Thickness of door frame ,if fabricated or multibend)	-	15000	-
5(Table-1)(Dimension of the rebate coming under share)	-	15000	-
5(Table-1)(Thickness of grill gate angle/section)	-	15000	-
5(Table-1)(Diameter of grill gate rod)	-	15000	-
5(Table-1)(Pitch of grill gate rod)	-	15000	-
5(Table-1)(Thickness of door slab,thickness over rebate)	-	15000	-
5(Table-1)(Thickness of the door over lock)	-	15000	-
5(Table-1)(Thickness of drill & oxyacetylene torch resis. layer(exclue MS plate)	-	15000	-
5(Table-1)(Wall thickness)	-	15000	-
5(Table-1)(Number of locks)	-	15000	-
5(Table-1)(Number of shooting bolys on hinge side)	-	15000	-
5(Table-1)(Number of shooting bolts at top)	-	15000	-
5(Table-1)(Number of shooting bolts at bottom)	-	15000	-
5(Table-1)(Cross sectional area as per shooting bolt)	-	15000	-
5(Table-1)(Depth engagement of shooting)	-	15000	-
6(Materail)	-	15000	-
7(Classification)	-	15000	-
8 & 8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1.1.1(Locking device (unpickable dual control lock))	-	15000	-
8.1.2(Main Door- Outer & inner plate thickness)	-	15000	-
8.1.2.1(Door(Finish &Gap of frame/edge with any place))	-	15000	-
8.2(Door frame (No.of barckets & Size for gripping))	-	15000	-
8.2.1(Rebate of the door frame)	-	15000	-
8.2.2(Compression mechanism)	-	15000	-
8.2.3(Crane hinge mechanism)	-	15000	-
8.3(Lock case)	-	15000	-
8.3.2(Bolt work)	-	15000	-
8.3.2.2(Construction (of bolt work))	-	15000	-
8.3.2.3(Bearing piller)	-	15000	-
8.4.1(Shooting bolt control (By lock))	-	15000	-
8.4.2(Test of key-Lock)	-	15000	-
8.4.3(Lock fixing bolts)	-	15000	-
8.4.4(Time lock)	-	15000	-
8.4.5(Automatic Relocking devise)	-	15000	-
9 &9.1(Hinges)	-	15000	-
9.1.1(Adjusting bolt)	-	15000	-
9.3(Foot bringe)	-	15000	-
9.4(Vault lighting control)	-	15000	-
10 &10.1(Dents,Burrs & Edges)	-	15000	-
10.2(Colour coating thickness (Surafce paint))	-	15000	-
10.3(Cross Hatch test)	-	15000	-
10.4(Door (Stainless cladding))	-	15000	-
11.1 &11.2(Test criteria for confomity -Burglaty attack)	-	15000	-
11.1 &11.2(Test criteria for confomity -Fire resistancey)	-	15000	-
12(Marking of door)	-	15000	-
12.2(Marking on keys)	-	15000	-
11.1 (3)(Fire and stream hose IS 11188 (Part 3))	-	15000	-
11.1 (2)(Fire endurance IS 11188 (Part 3))	-	150000	-
11.1 (1)(Burglary resistance IS 11188 (Part 2))	-	150000	-
10.4(Alternate to Cl 10.4)	-	15000	-
10.3(Cross Hatch Test)	-	15000	-
10(FINISH)	-	15000	-
9.4(Vault Lighting Control)	-	15000	-
9.3(Foot Bridge)	-	15000	-
9.2(Handles)	-	15000	-
9.1.1(Adjusting Bolt)	-	15000	-
9.1(Hinges)	-	15000	-
9(DOOR FITTINGS)	-	15000	-
8.4.5(Automatic Relocking Device)	-	15000	-
8.4.4(Time Lock)	-	15000	-
8.4(Lock)	-	15000	-
8.3.2.2(Construction)	-	15000	-
8.3.2.1(The number of bolts and their minimum dimension)	-	15000	-
8.3.2(Bolt Work)	-	15000	-
8.3.1(Lock Case)	-	15000	-
8.3(Locking Mechanism)	-	15000	-
8.2.3(Crane Hinge Mechanism)	-	15000	-
8.2.2(Compression Mechanism)	-	15000	-
8.2.1(Rebate of the Door Frame)	-	15000	-
8.2(Doors Frame)	-	15000	-
8.1.2(Main Door (Outside))	-	15000	-
8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1 Fig. 1(Doors)	-	15000	-
8(CONSTRUCTION AND GENERALREQUIREMENTS)	-	15000	-
5 Table 1(bolts, Min)	-	15000	-
5 Table 1(xix) Depth of engagement of shooting)	-	15000	-
5 Table 1(cross sectional area, Min,sq mm)	-	15000	-
5 Table 1(xviii) Diameter of shooting bolts, Min)	-	15000	-
5 Table 1(xvi) Number of shooting bolts at top,Min)	-	15000	-
5 Table 1(xv) Number of shooting bolts on opposite side,Min)	-	15000	-
5 Table 1(xiv) Number of shooting bolts on hinge side, Min)	-	15000	-
5 Table 1(xiii) Number of locks)	-	15000	-
5 Table 1(xii) Wall thickness (recommendation))	-	15000	-
5 Table 1(xi) Thickness of drill and oxyacetylene torch resisting layer (excluding mild steel plates),Min)	-	15000	-
5 Table 1(ix) Thickness of doors slab, thickness over rebate)	-	15000	-
5 Table 1(viii) Pitch of grill gate rods)	-	15000	-
5 Table 1(vii) Diameter of grill gate rods, Min)	-	15000	-
5 Table 1(vi) Thickens of grill gate angles or section made out of M.S. plates, Min)	-	15000	-
5 Table 1(v) Dimension of the rebate coming under shear)	-	15000	-
5 Table 1(iv (b) Thickness of door frame, if fabricated from single plate to form channel/multi-bend section, Min)	-	15000	-
5 Table 1(ii (a) Height H, Min b) Width W, Min iv(a) Thickness of door frame angle, channel or section made out of M.S. plates, if built up to form a channel,Min)	-	15000	-
5 Table 1(iii) Inside dimension or clear opening when door shutters are swung open at 180 degree)	-	15000	-
5 Table 1(ii (b) Width W)	-	15000	-
5 Table 1(ii (a) Height, H)	-	15000	-
5 Table 1(ii) Overall dimension of vault door)	-	15000	-
5 Table 1(i) Door Type)	-	15000	-
4(Type)	-	15000	-
5(Table-1)(Type of Door)	-	15000	-
5(Table-1)(Overall dimesion of door)	-	15000	-
5(Table-1)(Inside dimension or clear opening of door)	-	15000	-
5(Table-1)(Thickness of door frame angle-made of Plate,if bulit up to form a channel)	-	15000	-
5(Table-1)(Thickness of door frame ,if fabricated or multibend)	-	15000	-
5(Table-1)(Dimension of the rebate coming under share)	-	15000	-
5(Table-1)(Thickness of grill gate angle/section)	-	15000	-
5(Table-1)(Diameter of grill gate rod)	-	15000	-
5(Table-1)(Pitch of grill gate rod)	-	15000	-
5(Table-1)(Thickness of door slab,thickness over rebate)	-	15000	-
5(Table-1)(Thickness of the door over lock)	-	15000	-
5(Table-1)(Thickness of drill & oxyacetylene torch resis. layer(exclue MS plate)	-	15000	-
5(Table-1)(Wall thickness)	-	15000	-
5(Table-1)(Number of locks)	-	15000	-
5(Table-1)(Number of shooting bolys on hinge side)	-	15000	-
5(Table-1)(Number of shooting bolts on opposite)	-	15000	-
5(Table-1)(Number of shooting bolts at top)	-	15000	-
5(Table-1)(Number of shooting bolts at bottom)	-	15000	-
5(Table-1)(Cross sectional area as per shooting bolt)	-	15000	-
5(Table-1)(Depth engagement of shooting)	-	15000	-
6(Materail)	-	15000	-
7(Classification)	-	15000	-
8 & 8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1.1.1(Locking device (unpickable dual control lock))	-	15000	-
8.1.2(Main Door- Outer & inner plate thickness)	-	15000	-
8.1.2.1(Door(Finish &Gap of frame/edge with any place))	-	15000	-
8.2(Door frame (No.of barckets & Size for gripping))	-	15000	-
8.2.1(Rebate of the door frame)	-	15000	-
8.2.2(Compression mechanism)	-	15000	-
8.2.3(Crane hinge mechanism)	-	15000	-
8.3(Lock case)	-	15000	-
8.3.2(Bolt work)	-	15000	-
8.3.2.2(Construction (of bolt work))	-	15000	-
8.3.2.3(Bearing piller)	-	15000	-
8.4.1(Shooting bolt control (By lock))	-	15000	-
8.4.2(Test of key-Lock)	-	15000	-
8.4.3(Lock fixing bolts)	-	15000	-
8.4.4(Time lock)	-	15000	-
8.4.5(Automatic Relocking devise)	-	15000	-
9 &9.1(Hinges)	-	15000	-
9.1.1(Adjusting bolt)	-	15000	-
9.2(Handles)	-	15000	-
9.3(Foot bringe)	-	15000	-
9.4(Vault lighting control)	-	15000	-
10 &10.1(Dents,Burrs & Edges)	-	15000	-
10.2(Colour coating thickness (Surafce paint))	-	15000	-
10.3(Cross Hatch test)	-	15000	-
10.4(Door (Stainless cladding))	-	15000	-
11.1 &11.2(Test criteria for confomity -Burglaty attack)	-	15000	-
11.1 &11.2(Test criteria for confomity -Fire resistancey)	-	15000	-
12(Marking of door)	-	15000	-
12.2(Marking on keys)	-	15000	-
4(Type)	-	15000	-
5(Table-1)(5(Table-1))	-	15000	-
5(Table-1)(Overall dimesion of door)	-	15000	-
5(Table-1)(Inside dimension or clear opening of door)	-	15000	-
5(Table-1)(Thickness of door frame angle-made of Plate,if bulit up to form a channel)	-	15000	-
5(Table-1)(Thickness of door frame ,if fabricated or multibend)	-	15000	-
5(Table-1)(Dimension of the rebate coming under share)	-	15000	-
5(Table-1)(Thickness of grill gate angle/section)	-	15000	-
5(Table-1)(Diameter of grill gate rod)	-	15000	-
5(Table-1)(Pitch of grill gate rod)	-	15000	-
5(Table-1)(Thickness of door slab,thickness over rebate)	-	15000	-
5(Table-1)(Thickness of the door over lock)	-	15000	-
5(Table-1)(Thickness of drill & oxyacetylene torch resis. layer(exclue MS plate)	-	15000	-
5(Table-1)(Wall thickness)	-	15000	-
5(Table-1)(Number of locks)	-	15000	-
5(Table-1)(Number of shooting bolys on hinge side)	-	15000	-
5(Table-1)(Number of shooting bolts at top)	-	15000	-
5(Table-1)(Number of shooting bolts at bottom)	-	15000	-
5(Table-1)(Cross sectional area as per shooting bolt)	-	15000	-
5(Table-1)(Depth engagement of shooting)	-	15000	-
6(Materail)	-	15000	-
7(Classification)	-	15000	-
8 & 8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1.1.1(Locking device (unpickable dual control lock))	-	15000	-
8.1.2(Main Door- Outer & inner plate thickness)	-	15000	-
8.1.2.1(Door(Finish &Gap of frame/edge with any place))	-	15000	-
8.2(Door frame (No.of barckets & Size for gripping))	-	15000	-
8.2.1(Rebate of the door frame)	-	15000	-
8.2.2(Compression mechanism)	-	15000	-
8.2.3(Crane hinge mechanism)	-	15000	-
8.3(Lock case)	-	15000	-
8.3.2(Bolt work)	-	15000	-
8.3.2.2(Construction (of bolt work))	-	15000	-
8.3.2.3(Bearing piller)	-	15000	-
8.4.1(Shooting bolt control (By lock))	-	15000	-
8.4.2(Test of key-Lock)	-	15000	-
8.4.3(Lock fixing bolts)	-	15000	-
8.4.4(Time lock)	-	15000	-
8.4.5(Automatic Relocking devise)	-	15000	-
9 &9.1(Hinges)	-	15000	-
9.1.1(Adjusting bolt)	-	15000	-
9.3(Foot bringe)	-	15000	-
9.4(Vault lighting control)	-	15000	-
10 &10.1(Dents,Burrs & Edges)	-	15000	-
10.2(Colour coating thickness (Surafce paint))	-	15000	-
10.3(Cross Hatch test)	-	15000	-
10.4(Door (Stainless cladding))	-	15000	-
11.1 &11.2(Test criteria for confomity -Burglaty attack)	-	15000	-
11.1 &11.2(Test criteria for confomity -Fire resistancey)	-	15000	-
12(Marking of door)	-	5000	-
12.2(Marking on keys)	-	5000	-
11.1 (3)(Fire and stream hose IS 11188 (Part 3))	-	15000	-
11.1 (2)(Fire endurance IS 11188 (Part 3))	-	150000	-
11.1 (1)(Burglary resistance IS 11188 (Part 2))	-	150000	-
10.4(Alternate to Cl 10.4)	-	15000	-
10.3(Cross Hatch Test)	-	15000	-
10(FINISH)	-	15000	-
9.4(Vault Lighting Control)	-	15000	-
9.3(Foot Bridge)	-	15000	-
9.2(Handles)	-	15000	-
9.1.1(Adjusting Bolt)	-	15000	-
9.1(Hinges)	-	15000	-
9(DOOR FITTINGS)	-	15000	-
8.4.5(Automatic Relocking Device)	-	15000	-
8.4.4(Time Lock)	-	15000	-
8.4(Lock)	-	15000	-
8.3.2.2(Construction)	-	15000	-
8.3.2.1(The number of bolts and their minimum dimension)	-	15000	-
8.3.2(Bolt Work)	-	15000	-
8.3.1(Lock Case)	-	15000	-
8.3(Locking Mechanism)	-	15000	-
8.2.3(Crane Hinge Mechanism)	-	15000	-
8.2.2(Compression Mechanism)	-	15000	-
8.2.1(Rebate of the Door Frame)	-	15000	-
8.2(Doors Frame)	-	15000	-
8.1.2(Main Door (Outside))	-	15000	-
8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1 Fig. 1(Doors)	-	15000	-
8(CONSTRUCTION AND GENERALREQUIREMENTS)	-	15000	-
5 Table 1(bolts, Min)	-	15000	-
5 Table 1(xix) Depth of engagement of shooting)	-	15000	-
5 Table 1(cross sectional area, Min,sq mm)	-	15000	-
5 Table 1(xviii) Diameter of shooting bolts, Min)	-	15000	-
5 Table 1(xvi) Number of shooting bolts at top,Min)	-	15000	-
5 Table 1(xv) Number of shooting bolts on opposite side,Min)	-	15000	-
5 Table 1(xiv) Number of shooting bolts on hinge side, Min)	-	15000	-
5 Table 1(xiii) Number of locks)	-	15000	-
5 Table 1(xii) Wall thickness (recommendation))	-	15000	-
5 Table 1(xi) Thickness of drill and oxyacetylene torch resisting layer (excluding mild steel plates),Min)	-	15000	-
5 Table 1(ix) Thickness of doors slab, thickness over rebate)	-	15000	-
5 Table 1(viii) Pitch of grill gate rods)	-	15000	-
5 Table 1(vii) Diameter of grill gate rods, Min)	-	15000	-
5 Table 1(vi) Thickens of grill gate angles or section made out of M.S. plates, Min)	-	15000	-
5 Table 1(v) Dimension of the rebate coming under shear)	-	15000	-
5 Table 1(iv (b) Thickness of door frame, if fabricated from single plate to form channel/multi-bend section, Min)	-	15000	-
5 Table 1(ii (a) Height H, Min b) Width W, Min iv(a) Thickness of door frame angle, channel or section made out of M.S. plates, if built up to form a channel,Min)	-	15000	-
5 Table 1(iii) Inside dimension or clear opening when door shutters are swung open at 180 degree)	-	15000	-
5 Table 1(ii (b) Width W)	-	15000	-
5 Table 1(ii (a) Height, H)	-	15000	-
5 Table 1(ii) Overall dimension of vault door)	-	15000	-
5 Table 1(i) Door Type)	-	15000	-
4(Type)	-	15000	-
5(Table-1)(Type of Door)	-	15000	-
5(Table-1)(Overall dimesion of door)	-	15000	-
5(Table-1)(Inside dimension or clear opening of door)	-	15000	-
5(Table-1)(Thickness of door frame angle-made of Plate,if bulit up to form a channel)	-	15000	-
5(Table-1)(Thickness of door frame ,if fabricated or multibend)	-	15000	-
5(Table-1)(Dimension of the rebate coming under share)	-	15000	-
5(Table-1)(Thickness of grill gate angle/section)	-	15000	-
5(Table-1)(Diameter of grill gate rod)	-	15000	-
5(Table-1)(Pitch of grill gate rod)	-	15000	-
5(Table-1)(Thickness of door slab,thickness over rebate)	-	15000	-
5(Table-1)(Thickness of the door over lock)	-	15000	-
5(Table-1)(Thickness of drill & oxyacetylene torch resis. layer(exclue MS plate)	-	15000	-
5(Table-1)(Wall thickness)	-	15000	-
5(Table-1)(Number of locks)	-	15000	-
5(Table-1)(Number of shooting bolys on hinge side)	-	15000	-
5(Table-1)(Number of shooting bolts on opposite)	-	15000	-
5(Table-1)(Number of shooting bolts at top)	-	15000	-
5(Table-1)(Number of shooting bolts at bottom)	-	15000	-
5(Table-1)(Cross sectional area as per shooting bolt)	-	15000	-
5(Table-1)(Depth engagement of shooting)	-	15000	-
6(Materail)	-	15000	-
7(Classification)	-	15000	-
8 & 8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1.1.1(Locking device (unpickable dual control lock))	-	15000	-
8.1.2(Main Door- Outer & inner plate thickness)	-	15000	-
8.1.2.1(Door(Finish &Gap of frame/edge with any place))	-	15000	-
8.2(Door frame (No.of barckets & Size for gripping))	-	15000	-
8.2.1(Rebate of the door frame)	-	15000	-
8.2.2(Compression mechanism)	-	15000	-
8.2.3(Crane hinge mechanism)	-	15000	-
8.3(Lock case)	-	15000	-
8.3.2(Bolt work)	-	15000	-
8.3.2.2(Construction (of bolt work))	-	15000	-
8.3.2.3(Bearing piller)	-	15000	-
8.4.1(Shooting bolt control (By lock))	-	15000	-
8.4.2(Test of key-Lock)	-	15000	-
8.4.3(Lock fixing bolts)	-	15000	-
8.4.4(Time lock)	-	15000	-
8.4.5(Automatic Relocking devise)	-	15000	-
9 &9.1(Hinges)	-	15000	-
9.1.1(Adjusting bolt)	-	15000	-
9.2(Handles)	-	15000	-
9.3(Foot bringe)	-	15000	-
9.4(Vault lighting control)	-	15000	-
10 &10.1(Dents,Burrs & Edges)	-	15000	-
10.2(Colour coating thickness (Surafce paint))	-	15000	-
10.3(Cross Hatch test)	-	15000	-
10.4(Door (Stainless cladding))	-	15000	-
11.1 &11.2(Test criteria for confomity -Burglaty attack)	-	15000	-
11.1 &11.2(Test criteria for confomity -Fire resistancey)	-	15000	-
12(Marking of door)	-	15000	-
12.2(Marking on keys)	-	15000	-
4(Type)	-	15000	-
5(Table-1)(5(Table-1))	-	15000	-
5(Table-1)(Overall dimesion of door)	-	15000	-
5(Table-1)(Inside dimension or clear opening of door)	-	15000	-
5(Table-1)(Thickness of door frame angle-made of Plate,if bulit up to form a channel)	-	15000	-
5(Table-1)(Thickness of door frame ,if fabricated or multibend)	-	15000	-
5(Table-1)(Dimension of the rebate coming under share)	-	15000	-
5(Table-1)(Thickness of grill gate angle/section)	-	15000	-
5(Table-1)(Diameter of grill gate rod)	-	15000	-
5(Table-1)(Pitch of grill gate rod)	-	15000	-
5(Table-1)(Thickness of door slab,thickness over rebate)	-	15000	-
5(Table-1)(Thickness of the door over lock)	-	15000	-
5(Table-1)(Thickness of drill & oxyacetylene torch resis. layer(exclue MS plate)	-	15000	-
5(Table-1)(Wall thickness)	-	15000	-
5(Table-1)(Number of locks)	-	15000	-
5(Table-1)(Number of shooting bolys on hinge side)	-	15000	-
5(Table-1)(Number of shooting bolts at top)	-	15000	-
5(Table-1)(Number of shooting bolts at bottom)	-	15000	-
5(Table-1)(Cross sectional area as per shooting bolt)	-	15000	-
5(Table-1)(Depth engagement of shooting)	-	15000	-
6(Materail)	-	15000	-
7(Classification)	-	15000	-
8 & 8.1.1(Ventilating Grill Gate (Inside))	-	15000	-
8.1.1.1(Locking device (unpickable dual control lock))	-	15000	-
8.1.2(Main Door- Outer & inner plate thickness)	-	15000	-
8.1.2.1(Door(Finish &Gap of frame/edge with any place))	-	15000	-
8.2(Door frame (No.of barckets & Size for gripping))	-	15000	-
8.2.1(Rebate of the door frame)	-	15000	-
8.2.2(Compression mechanism)	-	15000	-
8.2.3(Crane hinge mechanism)	-	15000	-
8.3(Lock case)	-	15000	-
8.3.2(Bolt work)	-	15000	-
8.3.2.2(Construction (of bolt work))	-	15000	-
8.3.2.3(Bearing piller)	-	15000	-
8.4.1(Shooting bolt control (By lock))	-	15000	-
8.4.2(Test of key-Lock)	-	15000	-
8.4.3(Lock fixing bolts)	-	15000	-
8.4.4(Time lock)	-	15000	-
8.4.5(Automatic Relocking devise)	-	15000	-
9 &9.1(Hinges)	-	15000	-
9.1.1(Adjusting bolt)	-	15000	-
9.3(Foot bringe)	-	15000	-
9.4(Vault lighting control)	-	15000	-
10 &10.1(Dents,Burrs & Edges)	-	15000	-
10.2(Colour coating thickness (Surafce paint))	-	15000	-
10.3(Cross Hatch test)	-	15000	-
10.4(Door (Stainless cladding))	-	15000	-
11.1 &11.2(Test criteria for confomity -Burglaty attack)	-	15000	-
11.1 &11.2(Test criteria for confomity -Fire resistancey)	-	15000	-
12(Marking of door)	-	15000	-
12.2(Marking on keys)	-	15000	-

14 Nov, 2027

-
Included w.e.f. 28.03.2025

IS 550 : Part 1 (2022)

Safes: Part 1 specification Fifth Revision

258000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	124999.97	-
5.1(Dimensions)	-	10000	-
5.2(Sizes)	-	10000	-
5.2(Table-2)(Inside dimensions)	-	10000	-
5.2(Table-2)(Tolerance on inside dimensions)	-	10000	-
5.2(Table-2)(Internal volume)	-	10000	-
5.2(Table-2)(Tolerance on interanal volume)	-	10000	-
5.2(Table-2)(Minumum Weight)	-	10000	-
5.2(Table-2)(Thickness of Plates (outer bodys& Door))	-	10000	-
5.2(Table-2)(Thickness of Door slab)	-	10000	-
5.2(Table-2)(Thickness of door overbolt work)	-	10000	-
5.2(Table-2)(Number of lock on the door)	-	10000	-
5.2(Table-2)(Any other type of lock)	-	10000	-
5.2(Table-2)(Number of bolt on hinge side)	-	10000	-
5.2(Table-2)(Number of bolt on opposite hinge)	-	10000	-
5.2(Table-2)(No.of bolt at the top)	-	10000	-
5.2(Table-2)(No.of bolt at the bottom)	-	10000	-
5.2(Table-2)(Size of each bolt (area of bolt section))	-	10000	-
5.2(Table-2)(Depth engagement of bolt)	-	10000	-
6(Material declaration)	-	10000	-
7(Desigantion-Delaration)	-	10000	-
8.1(Body (Construction & workmanship))	-	10000	-
8.2(Door (Gap))	-	10000	-
8.4.1(Hinges)	-	10000	-
8.4.2(Bolts)	-	10000	-
8.5(Handle)	-	10000	-
8.6.1(Lock (key type) Garde)	-	10000	-
8.6.1(Lock (key type)classification)	-	10000	-
8.6.1(Lock (key type)construction)	-	10000	-
8.6.1(Lock(key type) leaver thickness)	-	10000	-
8.6.1(Lock (key type)Material)	-	10000	-
8.6.1(Lock (key type)corrosion protection materail)	-	10000	-
8.6.1(Lock(key type) -Endurance test)	-	10000	-
8.6.1(Lock(key type)-Bolt forcing test)	-	10000	-
8.6.1(Lock(key type)-salt spray solution test)	-	10000	-
8.6.1(Lock(key type)-key strength test)	-	10000	-
8.6.1(Lock(key type) -Marking)	-	10000	-
8.6.1(Lock(Key type) -Key Marking)	-	10000	-
8.6.1(Mechanical combination lock -Classification)	-	10000	-
8.6.1(Mechanical combination lock -Construction)	-	10000	-
8.6.1(Mechanical combination lock -Metallic parts)	-	10000	-
8.6.1(Mechanical combination lock -Corrosion Prot)	-	10000	-
8.6.1(Mechanical combination lock -Operation test)	-	10000	-
8.6.1(Mechanical cmbination lock -Manipulation)	-	10000	-
8.6.1(Mechanical combination lock -Punching attack)	-	10000	-
8.6.1(Mechanical combination lock -Endurance test)	-	10000	-
8.6.1(Mechanical combination lock-Salt spary test)	-	10000	-
8.6.1(Mechanical combination lock-Strength test)	-	10000	-
8.6.1(Mechanical combination lock-Aging-stress Dist)	-	10000	-
8.6.1(Mechanical combination lock-Moisture Absorp)	-	10000	-
8.6.1(Mechanical combination lock-Vibration test)	-	10000	-
8.6.1(Mechanical combination lock-Marking)	-	10000	-
8.6.1(Any other lock)	-	10000	-
8.6.4(Lock Bolt engagement)	-	10000	-
8.6.5(Additional provision- retrofitting time lock)	-	10000	-
8.7(Automatic re-locking device)	-	10000	-
8.8(Cable hole size)	-	10000	-
9(Internal fixture)	-	10000	-
10(Painting)	-	10000	-
10.1(Cross hatch test)	-	10000	-
11.1(Marking of safe)	-	10000	-
12(Burglary attack)	-	99999.97	-
12(Fire Resistance)	-	150000	-
4(Classification)	-	100000	-
5.1(Dimensions)	-	10000	-
5.2(Sizes)	-	10000	-
5.2(Table-2)(Inside dimensions)	-	10000	-
5.2(Table-2)(Tolerance on inside dimensions)	-	10000	-
5.2(Table-2)(Internal volume)	-	10000	-
5.2(Table-2)(Tolerance on interanal volume)	-	10000	-
5.2(Table-2)(Minumum Weight)	-	10000	-
5.2(Table-2)(Thickness of Plates (outer bodys& Door))	-	10000	-
5.2(Table-2)(Thickness of Door slab)	-	10000	-
5.2(Table-2)(Thickness of door overbolt work)	-	10000	-
5.2(Table-2)(Number of lock on the door)	-	10000	-
5.2(Table-2)(Any other type of lock)	-	10000	-
5.2(Table-2)(Number of bolt on hinge side)	-	10000	-
5.2(Table-2)(Number of bolt on opposite hinge)	-	10000	-
5.2(Table-2)(No.of bolt at the top)	-	10000	-
5.2(Table-2)(No.of bolt at the bottom)	-	10000	-
5.2(Table-2)(Size of each bolt (area of bolt section))	-	10000	-
5.2(Table-2)(Depth engagement of bolt)	-	10000	-
6(Material declaration)	-	10000	-
7(Desigantion-Delaration)	-	10000	-
8.1(Body (Construction & workmanship))	-	10000	-
8.2(Door (Gap))	-	10000	-
8.4.1(Hinges)	-	10000	-
8.4.2(Bolts)	-	10000	-
8.5(Handle)	-	10000	-
8.6.1(Lock (key type) Garde)	-	10000	-
8.6.1(Lock (key type)classification)	-	10000	-
8.6.1(Lock (key type)construction)	-	10000	-
8.6.1(Lock(key type) leaver thickness)	-	10000	-
8.6.1(Lock (key type)Material)	-	10000	-
8.6.1(Lock (key type)corrosion protection materail)	-	10000	-
8.6.1(Lock(key type) -Endurance test)	-	10000	-
8.6.1(Lock(key type)-Bolt forcing test)	-	10000	-
8.6.1(Lock(key type)-salt spray solution test)	-	10000	-
8.6.1(Lock(key type)-key strength test)	-	10000	-
8.6.1(Lock(key type) -Marking)	-	10000	-
8.6.1(Lock(Key type) -Key Marking)	-	10000	-
8.6.1(Mechanical combination lock -Classification)	-	10000	-
8.6.1(Mechanical combination lock -Construction)	-	10000	-
8.6.1(Mechanical combination lock -Metallic parts)	-	10000	-
8.6.1(Mechanical combination lock -Corrosion Prot)	-	10000	-
8.6.1(Mechanical combination lock -Operation test)	-	10000	-
8.6.1(Mechanical cmbination lock -Manipulation)	-	10000	-
8.6.1(Mechanical combination lock -Punching attack)	-	10000	-
8.6.1(Mechanical combination lock -Endurance test)	-	10000	-
8.6.1(Mechanical combination lock-Salt spary test)	-	10000	-
8.6.1(Mechanical combination lock-Strength test)	-	10000	-
8.6.1(Mechanical combination lock-Aging-stress Dist)	-	10000	-
8.6.1(Mechanical combination lock-Moisture Absorp)	-	10000	-
8.6.1(Mechanical combination lock-Vibration test)	-	10000	-
8.6.1(Mechanical combination lock-Marking)	-	10000	-
8.6.1(Any other lock)	-	10000	-
8.6.4(Lock Bolt engagement)	-	10000	-
8.6.5(Additional provision- retrofitting time lock)	-	10000	-
8.7(Automatic re-locking device)	-	10000	-
8.8(Cable hole size)	-	10000	-
9(Internal fixture)	-	10000	-
10(Painting)	-	10000	-
10.1(Cross hatch test)	-	10000	-
11.1(Marking of safe)	-	10000	-
12(Burglary attack)	-	100000	-
12(Fire Resistance)	-	150000	-

14 Nov, 2027

-
Included w.e.f. 28.03.2025

IS 5244 (2020)

Safe Deposit Locker Cabinets — Specification ( Fourth Revision )

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4.1( Types )	-	1000	-
Cl. 6 (Fig-5)(Cabinet Size (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Finish)	-	1000	-
Table 1(Finish)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.2(Design and Manufacture)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl. 7.4(Design and Manufacture)	-	1000	-
Cl. 7.5(Design and Manufacture)	-	1000	-
Cl. 7.6(Design and Manufacture)	-	1000	-
Cl. 8(Workmanship)	-	1000	-
Cl. 8.2(Tolerance)	-	1000	-
Cl. 9.1(Testing)	-	1000	-
Cl. 9.2(Testing)	-	1000	-
Cl. 9.3(Cross Hatch Test)	-	1000	-
Cl. 10.1(Marking)	-	1000	-
Cl. 10.2(Marking)	-	1000	-
Cl. 10.3(Marking)	-	1000	-
Cl. 10.4(Marking on Keys)	-	1000	-
Cl. 11(Packing)	-	1000	-
Cl. 4.1( Types )	-	1000	-
Cl. 6 (Fig-5)(Cabinet Size (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Finish)	-	1000	-
Table 1(Finish)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.2(Design and Manufacture)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl. 7.4(Design and Manufacture)	-	1000	-
Cl. 7.5(Design and Manufacture)	-	1000	-
Cl. 7.6(Design and Manufacture)	-	1000	-
Cl. 8(Workmanship)	-	1000	-
Cl. 8.2(Tolerance)	-	1000	-
Cl. 9.1(Testing)	-	1000	-
Cl. 9.2(Testing)	-	1000	-
Cl. 9.3(Cross Hatch Test)	-	1000	-
Cl. 10.1(Marking)	-	1000	-
Cl. 10.2(Marking)	-	1000	-
Cl. 10.3(Marking)	-	1000	-
Cl. 10.4(Marking on Keys)	-	1000	-
Cl. 11(Packing)	-	1000	-
Cl. 4.1( Types )	-	1000	-
Cl. 6 (Fig-5)(Cabinet Size (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Finish)	-	1000	-
Table 1(Finish)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.2(Design and Manufacture)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl. 7.4(Design and Manufacture)	-	1000	-
Cl. 7.5(Design and Manufacture)	-	1000	-
Cl. 7.6(Design and Manufacture)	-	1000	-
Cl. 8(Workmanship)	-	1000	-
Cl. 8.2(Tolerance)	-	1000	-
Cl. 9.1(Testing)	-	1000	-
Cl. 9.2(Testing)	-	1000	-
Cl. 9.3(Cross Hatch Test)	-	1000	-
Cl. 10.1(Marking)	-	1000	-
Cl. 10.2(Marking)	-	1000	-
Cl. 10.3(Marking)	-	1000	-
Cl. 10.4(Marking on Keys)	-	1000	-
Cl. 11(Packing)	-	1000	-

14 Nov, 2027

-
Included w.e.f. 28.03.2025

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Ace Test Labs & Metrology Pvt. Ltd., Sonipat

PLOT NO. 68, HSIIDC, INDUSTRIAL ESTATE,RAI, SONIPAT, Sonipat, Haryana, 131029

8816921177 info@acetestgroup.com

Scope List