BIS - LIMS (Laboratory Information Management System)

Advance Firetec and Research Lab Pvt. Ltd.

B-3, Mangolpuri, Industrial Area Phase II, NEW DELHI, North West, Delhi, 110034

9971032375 aftrlab@gmail.com

Scope List

Reset

35 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 4947 (2006)

Foam concentrate for producing mechanical foam for fire fighting - Specification (Fourth Revision)

All

10000 View breakup
Rs.10000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Capacity and Contents)	-	500	NA
Cl 7(Performance Requirements )	-	3000	NA
Cl 7.3(Leakage Test)	-	5000	NA
Cl 8(Finish)	-	500	NA

Complete

01 Jul, 2024

IS 12585 (1988)

Specification for thermoplastic hoses (Textile Reinforced) for water - General purpose

Type 1,2&3. All sizes

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(Types)	-	1000	NA
Cl 4.1(Construction)	-	1000	NA
Cl 4.2(Dimensions & Tolerances)	-	5000	NA
Cl 4.3.1 & Appendix A(Loss in Mass on Heating)	-	3000	NA
Cl 4.3.2(Adhesion)	-	1000	NA
Cl 4.3.3(Pressure Requirements)	-	5000	NA
Cl 4.3.4(Minimum Bend Radius)	-	4000	NA
Cl 4.3.5(Low Temperature Flexibility)	-	5000	NA
Cl 3(Types)	-	1000	NA
Cl 4.1(Construction)	-	1000	NA
Cl 4.2(Dimensions & Tolerances)	-	5000	NA
Cl 4.3.1 & Appendix A(Loss in Mass on Heating)	-	3000	NA
Cl 4.3.2(Adhesion)	-	1000	NA
Cl 4.3.3(Pressure Requirements)	-	5000	NA
Cl 4.3.4(Minimum Bend Radius)	-	4000	NA
Cl 4.3.5(Low Temperature Flexibility)	-	5000	NA
Cl 3(Types)	-	1000	NA
Cl 4.1(Construction)	-	1000	NA
Cl 4.2(Dimensions & Tolerances)	-	5000	NA
Cl 4.3.1 & Appendix A(Loss in Mass on Heating)	-	3000	NA
Cl 4.3.2(Adhesion)	-	1000	NA
Cl 4.3.3(Pressure Requirements)	-	5000	NA
Cl 4.3.4(Minimum Bend Radius)	-	4000	NA
Cl 4.3.5(Low Temperature Flexibility)	-	5000	NA

Complete

01 Jul, 2024

IS 2097 (2012)

Foam making branch pipe and foam inductor - Specification (Second Revision)

FB5X,FB10X,FB20X

10000 View breakup
(Provisional testing charges): Rs.10,000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 - Table 1(PERFORMANCE REQUIREMENTS-The foam making branches shall conform to the performance requirements given below 1.Pressure )	-	1500	NA
6.1 - Table 1(2. Discharge Capacity(Water))	-	2000	NA
6.1 - Table 1(3. Foam)	-	2000	NA
6.1 - Table 1(4. Throw)	-	2000	NA
6.1 - Table 1(5. Expansion)	-	2000	NA
7.1(MARKING-The foam making branches shall be clearly and permanently marked with the following information:)	-	500	NA

Complete

01 Jul, 2024

IS 884 (1985)

Apecification for first - Aid hose - Reel for fire fighting (First Revision)

Type A & Type B

15000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Dimensions)	-	1000.00	NA
Cl 5.2(Resistance to Leakage)	-	2000.00	NA
Cl 5.3(Strength)	-	2000.00	NA
Cl 5.3(Strength)	-	2000.00	NA
Cl 5.4(Range & Water Flow Rate)	-	4000.00	NA
Cl 5.5(Swinging)	-	2000.00	NA
Cl 5.6(Reel Action)	-	1000.00	NA
Cl 6(Workmanship)	-	500.00	NA
Cl 7(Painting)	-	500.00	NA

Complete

01 Jul, 2024

IS 636 (2018)

Non - Percolating flexible fire fighting delivery hose - Specification (Fourth Revision)

Type 1,2 &3

62000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6.1.1(Inner lining shall be of rubber or rubberized fabric lining which is generally smooth and practically free from pitting and other imperfections)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl 6.1.2(Externally applied elastomeric coating or covering of the reinforcement, if present shall be generally smooth and practically free from pitting and other imperfections)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl 6.1.3(The jacket shall be practically free from dirt, knots, lumps, irregularities of the yarn and other visible defects.)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl.6.2(The internal diameter of the hose shall be measured by a suitable conical plug gauge and shall conform to the specified diameter with a tolerance of plus 2 and minus 0.0 mm.)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl.6.3(Unless specified otherwise, the standard length shall be 30 m. Unless otherwise specified, a tolerance of ± 2 percent shall be permitted on the length prescribed for the hose by the purchaser but the total of all lengths of hose supplied shall be not less than the total quantity specified by the purchaser.)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl.6.4(The average mass of hose per meter of 2 m length, without couplings attached, shall not be more than that prescribed in Table 1. For the determination of mass, sample of the hose shall be conditioned at 27 ± 2°C and 65 ± 5 percent relative humidity for a period of at least 48 h and then shall be weighed under the same conditions.)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl.6.5(For 30 m length of dry hose without couplings, the coil diameter shall not exceed 45 cm for Type 1, 50 cm for Type 2 and 55 cm for Type 3.)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl.6.6(Each hose length shall be subjected to an internal hydraulic pressure of 23 kgf/cm² in accordance with 8.1 of IS 443 (Part 3) increasing the pressure at the rate not exceeding 10 kgf/cm² per min and maintaining it for 1 min. Within this 1 min, the hose shall neither develop any leakage or sweating, nor shall any thread in the jacket break.)	-	3000	Type 1 - Rs 3000 Type 2 - Rs 3000 Type 3 - Rs 3000
Cl.6.7(A test length of hose, 1 m clear of fittings when subjected to an internal hydraulic pressure in accordance with 8.3 of IS 443 (Part 3) while increasing the pressure at the rate not exceeding 10 kgf/cm2 per min shall not burst or show leakage before a pressure of 38 kgf/cm2 is reached)	-	4000	Type 1 - Rs 4000 Type 2 - Rs 4000 Type 3 - Rs 4000
Cl.6.8(There shall be no sign of leakage or rupture and no thread in the jacket shall break after retaining the internal hydraulic pressure of 23 kgf/cm2 for 30 seconds.)	-	2000	Type 1 - Rs 2000 Type 2 - Rs 2000 Type 3 - Rs 2000
Cl.6.9(The increase in length shall not exceed 6 percent at an internal hydraulic pressure of 10 kgf/cm2 for 2 minutes.)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl.6.10(The increase in diameter shall not be more than 10% at an internal hydraulic pressure of 10 kgf/cm2 for 2 minutes.)	-	500	Type 1 - Rs 500 Type 2 - Rs 500 Type 3 - Rs 500
Cl 6.11 (Adhesion (Cl. 6.11.1))(Rate of separation shall not exceed 25 mm/min 1) Cover)	-	1000	Type 1 - NA Type 2 - NA Type 3 - Rs 1000
Cl 6.11 (Adhesion (Cl. 6.11.1))(Rate of separation shall not exceed 25 mm/min 2) Jet)	-	1000	Type 1 - NA Type 2 - NA Type 3 - Rs 500
Cl.6.11 Acccleraled Ageing Test (Cl. 6.11.2) - 1)(After ageing, there shall be no tackiness on the surface of lining or the surface of the cover. )	-	2000	Type 1 - Rs 2000 Type 2 - Rs 2000 Type 3 - Rs 2000
Cl.6.11 Acccleraled Ageing Test (Cl. 6.11.2) - 3)(Rate of separation shall not exceed 25 mm/min 1) Cover)	-	2000	Type 1 - Rs 2000 Type 2 - Rs 2000 Type 3 - Rs 2000
Cl.6.11 Acccleraled Ageing Test (Cl. 6.11.2) - 3)(Rate of separation shall not exceed 25 mm/min 2) Jet)	-	2000	Type 1 - Rs 2000 Type 2 - Rs 2000 Type 3 - Rs 2000
Cl.6.12(When determined by the method described in Annex C, the average number of cycles completed before bursting of three test pieces, shall not be less than the value specified in Table 2.)	-	3000	Type 1 - Rs 3000 Type 2 - Rs 3000 Type 3 - Rs 3000
Cl.6.13(When tested in accordance with Annex D, the amount of moisture absorbed shall not exceed 0.20 kg/m2 for Type 2 hoses and 0.02 kg/m2 for Type 3 hoses.)	-	1000	Type 1 - NA Type 2 - Rs 1000 Type 3 - Rs 1000
Cl.6.14(When tested by the method described in Annex E, none of the test samples shall burst at less than 8 s of the application of the hot cube for Type 2 and 20 s for Type 3 hose.)	-	2000	Type 1 - NA Type 2 - Rs 2000 Type 3 - Rs 2000
Cl.6.15 (1)(The length shall be laid horizontally and the central fully immersed portion of the hose shall be visually examined for any swelling of rubber, weathering and cracking in the rubber lining)	-	2000	Type 1 - Rs 2000 Type 2 - Rs 2000 Type 3 - Rs 2000
Cl.6.15 (2)(Rate of separation shall not exceed 25 mm/min 1) Cover)	-	2000	Type 1 - Rs 2000 Type 2 - Rs 2000 Type 3 - Rs 2000
Cl.6.15 (2)(Rate of separation shall not exceed 25 mm/min 2) Jet)	-	2000	Type 1 - Rs 2000 Type 2 - Rs 2000 Type 3 - Rs 2000
Cl.6.16(When tested by the method prescribed in IS 443 (Part 1), the lining (for Types 1, 2 and 3) and cover (for Type 3 only) of the hose shall neither develop cracking nor crazing when seen under X2 magnification, except at the cut edges of the hose)	-	25000	Type 1 - Rs 12500 Type 2 - Rs 12500 Type 3 - Rs 25000
Cl.6.17(When tested in accordance with Annex F, at a test temperature of, at a test temperature of 300 ± 10°C for Types 1 and 2, and 400 ± 10° C for Type 3, in none of the four tests shall the test piece show signs of leakage within 120 s from the application of the filament rod or on removal of this filament rod after the specified period)	-	10000	Type 1 - Rs 10000 Type 2 - Rs 10000 Type 3 - Rs 10000
Cl.6.18(When tested in accordance with Annex H, the pressure loss per 23 m length shall not exceed the values specified in Table 3 at the specified flow rate and inlet pressure (Recommendations for pressure testing of hoses in service are given at Annex G).)	-	4000	Type 1 - Rs 4000 Type 2 - Rs 4000 Type 3 - Rs 4000

Complete

01 Jul, 2024

Bureau of Indian Standards

The National Standards Body of India

Advance Firetec and Research Lab Pvt. Ltd.

B-3, Mangolpuri, Industrial Area Phase II, NEW DELHI, North West, Delhi, 110034

9971032375 aftrlab@gmail.com

Scope List