BIS - LIMS (Laboratory Information Management System)

NATIONAL TEST HOUSE-SR (NTH), Chennai

GOVT.OF INDIA,CSIR ROAD,TARAMANI., Chennai, Chennai, Tamil Nadu, 600113

9444944901 director-chn@nth.gov.in

Scope List

Reset

56 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 710 (2024)

MARINE PLYWOOD - SPECIFICATION (Third Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Timber)	-	250	-
Cl-4.2(Adhesive)	-	1000	-
Cl-5.1(Veneers)	-	250	-
Cl-5.2.1(Glueing)	-	250	-
Cl -5.2.2(Thickness of Veneers)	-	500	-
Cl - 5.2.3.1(Joint in Veneers)	-	250	-
Cl - 5.2.3.2(Edge joints)	-	250	-
Cl - 5.2.3.3(End joints)	-	250	-
Cl - 5.2.3.4(Scarf joints)	-	250	-
Cl - 5.2.4(Grain Direction)	-	250	-
Cl-5.3(Treatment)	-	500	-
Cl-5.4(Moisture Content)	-	1000	-
Cl-6.1(Dimensions (length))	-	500	-
Cl-6.2(Thickness)	-	500	-
Cl-6.3(Squareness)	-	500	-
Cl-7.1, 7.2, 7.3, 7.4, 7.5 & 7.6(Workmanship and finish)	-	500	-
Cl-9.3(Moisture Content)	-	1000	-
Cl-9.4.2(Glue Adhesion in Dry State- Adhesion of Plies)	-	1500	-
Cl-9.4.1(Glue Adhesion in Dry State- Glue Shear Strength -Average)	-	1500	-
Cl-9.5.1.1(Glue Adhesion in Water Resistance - Glue Shear Strength -Average)	-	2000	-
Cl-9.5.1.2(Water Resistance Test-Adhesion of plies)	-	1500	-
Cl-9.5.2(Water Resistance Test)	-	2000	-
Cl-9.6(Tensile Strength-Along the grain)	-	2000	-
Cl-9.7(Mycological Test -Adhesion)	-	1500	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	3000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	3000	-
Cl-9.9, Table-3 (i) a((Modulus of Elasticity: Across the Face Grain: Average) Wet Bending)	-	3000	-
Cl-9.9, Table-3 (i) b((Modulus of Elasticity: Across the Face Grain: Minimum Individual) Wet Bending)	-	3000	-
Cl-9.10(Retention of Preservative)	-	3000	-
Cl-9.11(Formaldehyde Content Test)	-	2000	-
Cl-9.12(Steady-State Formaldehyde Emission Test)	-	0	OPTIONAL TEST
Cl-9.4.2(Adhesion of Plies)	-	1500	-
5.1.1(Defects in veneers)	-	500	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	3000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	3000	-
Cl-9.9, Table-3 (ii) a((Modulus of Rupture: Across the Face Grain: Average) Wet Bending)	-	3000	-
Cl-9.9, Table-3 (ii) b((Modulus of Rupture: Across the Face Grain: Minimum Individual) Wet Bending)	-	3000	-
Cl-6.1(Dimensions (width))	-	500	-
Cl-8.3(Edge Straightness)	-	500	-
Cl-9.4.1(Glue Adhesion in Dry State- Glue Shear Strength –Minimum Individual)	-	1500	-
Cl-9.5.1.1(Glue Adhesion in Water Resistance - Glue Shear Strength –Minimum Individual)	-	2000	-
Cl-9.6(Tensile Strength-Across the grain)	-	2000	-
Cl-9.7(Glue Adhesion in Mycological test - Glue Shear Strength –Minimum Individual)	-	1500	-
Cl-9.7(Glue Adhesion in Mycological test - Glue Shear Strength -Average)	-	1500	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	3000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	3000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	3000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	3000	-
Cl-11.1(Marking)	-	1000	-
Cl-11.3(Marking)	-	1000	-
Cl. 9.9 (Table 3)((Modulus of Rupture: Along the Face Grain: Minimum Individual) Wet Bending)	-	3000	-
Cl. 9.9 (Table 3)((Modulus of Rupture: Along the Face Grain: Average) Wet Bending)	-	3000	-
Cl. 9.9 (Table 3)((Modulus of Elasticity: Along the Face Grain: Minimum Individual) Wet Bending)	-	3000	-
Cl. 9.9 (Table 3)((Modulus of Elasticity: Along the Face Grain: Average) Wet Bending)	-	3000	-

28 Nov, 2028

-
included w.e.f 11.08.2026

IS 2062 (Part 1) (2025)

Structural Steel - Part 1 - Hot Rolled Medium and High tensile Steel

All grades, types and sizes

23500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(MANUFACTURE)	-	0	-
Cl-7(FREEDOM FROM DEFECTS)	-	1000	-
Cl-8.1(Ladle Analysis)	-	5000	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis-C)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Mn)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- S)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- P)	-	0	-
Cl-8.1 & 8.2, Table-1(Ladle Analysis- Si )	-	0	-
Cl-8.1 & 8.2, Table-1(Carbon Equivalen t (CE), Max)	-	0	-
Cl-8.1 & 8.2, Note-1(Total aluminium)	-	0	-
Cl-8.1 & 8.2, Note-5(Nb)	-	0	-
Cl-8.1 & 8.2, Note-5(V)	-	0	-
Cl-8.1 & 8.2, Note-5(Ti)	-	0	-
Cl-8.1 & 8.2, Note-6(B)	-	0	-
Cl-8.2, Table 2 (i)(Carbon)	-	0	-
Cl-8.2, Table 2 (ii)(Manganese)	-	0	-
Cl-8.2, Table 2 (iii)(Sulphur)	-	0	-
Cl-8.2, Table 2 (iv)(Phosphorus)	-	0	-
Cl-8.2, Table 2 (v)(Silicon)	-	0	-
Cl-8.2, Table 2 (vi)(Copper)	-	0	-
Cl-8.2, Table 2 (vii)(Vanadium)	-	0	-
Cl-8.2, Table 2 (viii)(Niobium)	-	0	-
Cl-8.2, Table 2 (ix)(Titanium)	-	0	-
Cl-8.2, Table 2 (x)(Nitrogen)	-	0	-
Cl-10.1(Number of Tensile Tests)	-	0	-
Cl-10.2(Tensile Test Pieces)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Tensile Strength Rm, Min MPa7)	-	3000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Yield Stress ReH, Min MPa7)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Percentage Elongation A, Min at Gauge Length, L0=5.65√So)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Internal Bend Diameter Max)	-	0	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test-Temp°C)	-	5000	-
Cl-10.3, 10.3.1, 11.3.1, 12.2, 12.4 & 12.5, Table-3(Charpy Impact Test- Min J)	-	0	-
Cl-11.1(Number of Bend Tests)	-	0	-
Cl-11.3(Bend Test )	-	1500	-
Cl-12(Impact Test )	-	0	-
Cl-14, Table-4 (i)(Beam, column, channel and angle sections including parallel beam and column sections)	-	1000	-
Cl-14, Table-4 (ii)(Tee bars)	-	0	-
Cl-14, Table-4 (iii)(Bulb angles)	-	0	-
Cl-14, Table-4 (iv)(Plates, sheets, strips and flats)	-	0	-
Cl-14, Table-4 (vi)(Round and square bars)	-	0	-
Cl-14, Table-4 (vii)(Bulb flats)	-	0	-
Cl-14, Table-4 (viii)(Sheet piling sections)	-	0	-
Cl-14, Table-4 (ix)(Channel sections)	-	0	-
Cl-13(Other TestsNondestructive testing, Metallurgical tests )	-	7000	-
Cl-13.3(Strength of joint )	-	0	-
Cl-15(Tolerances)	-	0	-
Cl-16.1(Retests)	-	0	-
Cl-16.2(Re-heat Treatment)	-	0	-
Cl-11.2(Bend Test Piece)	-	0	-

28 Nov, 2028

-
included w.e.f 04.08.2026

IS 1180 : Part 1 (2014)

Outdoor Type Oil Immersed Distribution Transformers Upto and Including 2 500 kVA, 33kV - Specification Part 1 Mineral Oil Immersed (Fourth Revision)

105000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13.1(Marking (Rating Plates))	-	0	-
13.2(Terminal Marking Plate)	-	0	-
13.3(Marking )	-	0	-
13.4(Marking)	-	0	-
13.4.1(Marking)	-	0	-
14.1(MOUNTING ARRANGEMENT)	-	0	-
14.2(MOUNTING ARRANGEMENT)	-	0	-
14.3(MOUNTING ARRANGEMENT)	-	0	-
14.4(MOUNTING ARRANGEMENT)	-	0	-
15.1.1(TRANSFORMER TANK : Construction)	-	0	-
15.1.2(TRANSFORMER TANK : Construction)	-	0	-
15.1.3(TRANSFORMER TANK : Construction)	-	0	-
15.1.4(TRANSFORMER TANK : Construction)	-	0	-
15.1.5(TRANSFORMER TANK : Construction)	-	0	-
21.2 a)(Measurement of winding resistance )	-	1000	-
21.2 b)( Measurement of voltage ratio and check of phase displacemen)	-	2000	-
21.2 c)( Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load)	-	8000	-
21.2 d)(Measurement of no-load loss and current)	-	6000	-
21.2 e)(Measurement of insulation resistance)	-	1500	-
21.2 f)(Induced over-voltage withstand test)	-	3999.98	-
21.2 g)( Separate-source voltage withstand test)	-	2500	-
21.3(a )(Lightning impulse test)	-	65000	-
21.3(b)(Temperature-rise test)	-	40000	-
21.4 a)( Determination of sound levels)	-	7000	-
21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA ))	-	20000	-
21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA ))	-	5000	-
21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	20000	-
21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	5000	-
21.5.2.3( Oil leakage test (routine test))	-	7000	-
21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test))	-	20000	-
21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test))	-	5000	-
21.5.3.3(Oil leakage test (routine test))	-	7000	-
21.4 c(No load current at 112.5 percent voltage.)	-	2000	-
21.4 d(Paint adhesion tests)	-	5000	-
21.4 e(BDV and moisture content of oil in the transformer)	-	10000	-
6.9, 7.9, 8.9(Permissible Flux Density and Over Fluxing)	-	20000	-
11(Minimum clearance in Air)	-	0	-
16(Conservator for Non-sealed type Transformers)	-	0	-
20(Fittings)	-	0	-
6.8 (50%)(Total losses at 50 % load (Watts))	-	4000	-
7.8 (50%)(Total losses at 50 % load (Watts))	-	4000	-
8.8 (50%)(Total losses at 50 % load (Watts))	-	4000	-
6.8 (100%)(Total losses at 100 % load (Watts))	-	4000	-
7.8 (100%)(Total losses at 100 % load (Watts))	-	4000	-
8.8 (100%)(Total losses at 100 % load (Watts))	-	4000	-
21.5.1.3(Oil leakage test upto 200 KVA)	-	7000	-
9.1 f)(Mineral oil)	-	10000	-
15.2(Pressure and Vacuum Requirements)	-	20000	-
6.1(Rating)	-	0	-
6.2(Rated frequency)	-	0	-
6.3(Nominal system voltage)	-	0	-
6.4(Basic Insulation level )	-	0	-
6.5(No-Load Voltage Ratios)	-	1000	-
6.6(Winding connections and phase displacement)	-	1000	-
6.7(Tapping Range and Tapping Method)	-	0	-
6.9(Permissible Flux Density and Over Fluxing )	-	20000	-
7(Technical Parameters of three phase distribution trasnformers higher than 200kva)	-	0	-
8(Technical Parameters of single phase distribution transformers UP to and including 25 KVA )	-	0	-
10(Terminal arrangment )	-	0	-
18(Efficiency and regulation)	-	0	-
12(Connectors )	-	0	-
21.5.3.3(Oil leakage test)	-	7000	-
9.1a)(CRGO Electrical Steel)	-	0	-
9.1 b)(Amorphous core material)	-	0	-
9.1 c)(Copper/Aluminium conductor)	-	0	-
9.1 d)(Kraft paper)	-	0	-
9.1 e)(Press Board)	-	0	-
15.5(Total Dry Film Paint Thickness)	-	0	-
10(Terminal Arrangement)	-	0	-
15.4(Gasket)	-	0	-
19(Tolerances)	-	0	-
4(Service Conditions)	-	0	-
5(General )	-	0	-
9(Standard Materials)	-	0	-
11(Minimum Clearnaces air )	-	0	-
13(Marking )	-	0	-
14(Mounting arrangement)	-	0	-
15(Trasnformer Tank )	-	0	-
16(Conservator for Non-Sealed type Transformers)	-	0	-
18(Efficiency and Regulation)	-	0	-
19(Tolerances)	-	0	-
20(Fittings)	-	0	-
21(General )	-	0	-
22(Information required with enquiry and order )	-	0	-
6.8(Losses and impedance values)	-	8000	-
6.1(Limits of Temperature-rise)	-	0	-

28 Nov, 2028

-
-

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 & 8.2(Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	4000	-
6 & 8.2(Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Copper- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
6 & 8.2(Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	All elements test charges included in carbon
7.1.1(Diameter of Core Wire)	-	0	Included in Tensile Test charges
7.1.2(Length of Electrodes)	-	0	Included in Tensile Test charges
7.2.1(Contact End)	-	0	Included in Tensile Test charges
7.2.2(Arc striking End)	-	0	Included in Tensile Test charges
7.3(Concentricity of Flux covering with core wire)	-	0	Included in Tensile Test charges
7.4(Defects of Core wire and Coverings)	-	0	Included in Tensile Test charges
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-	0	13000
9.1.2 Table 6 ( Yield Stress -Annex F)	-	0	Included in Tensile Test charges
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-	0	Included in Tensile Test charges
9.1.3 Table 6 ( Impact Strength-Annex F)	-	0	Included in Tensile Test charges
9.2(Butt Weld Bend Test-IS 1599)	-	8000	-
9.3(Running PerformanceTest-Annex H)	-	2000	-
9.4(Increased Metal Recovery Test-IS 13043)	-	3000	-
9.5(Diffusible Hydrogen Evaluation Test-IS 11802)	-	5000	-
9.6(Radiographic Test- IS 1182)	-	1000	-

28 Nov, 2028

-
-

IS 303 (1989)

Plywood for General Purposes -

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	3000	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	3000	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	3000	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	3000	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	3000	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	3000	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	3000	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	3000	-
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	1500	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	2000	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	2000	-
11.3(Moisture Content - Part 1 of IS 1734)	-	1000	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	500	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	500	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	500	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	1000	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	1000	-
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	2000	-
5.1(Type - For BB Type)	-	500	-
5.1(Type - For AB Type)	-	500	-
5.1(Type - For AA Type)	-	500	-
4(Grade - For MR grade)	-	1000	-
4(Grade - For BWR grade)	-	1000	-
cl. 13.1(marking)	-	1000	-
cl. 13.2(marking)	-	1000	-
Cl-12 (Amendment No-2 OF IS 303)(OPTIONAL REQUIREMENT FOR ECO MARK)	-	1000	-
CL-8.2(Thickness)	-	1000	-
CL-7.2.3(Grain Direction)	-	1000	-
CL-7.2.1(Thickness)	-	1000	-
CL-6.2(Adhesive)	-	1000	-
CL-7.2.5.1(Gaps in cores and cross-bands)	-	1000	-

28 Nov, 2028

-
-

IS 1328 (1996)

Veneered Decorative Plywood -Specification

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Grade - For BWR)	-	1000	-
4.1(Grade - For MR)	-	1000	-
4.2(Type - For Type 1)	-	1000	-
4.2(Type - For Type 2)	-	1000	-
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	1000	-
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	1000	-
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	1000	-
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	1000	-
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	1000	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	1000	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	1000	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	1000	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	1000	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	1000	-
9(Finish - Cl. 9.1, 8.3)	-	1000	-
9(Finish - Cl. 9.2, 8.3)	-	1000	-
11(Tests - Moisture Content - Part 1 of IS 1734)	-	1000	-
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	2000	-
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	2000	-
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	1000	-

28 Nov, 2028

-
-

IS 12330 (1988)

Specificatioon for sulphate resisting Portland cement

11180 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Fineness 4031 Part 2)	-	1118	ALL FEES ARE INCLUDING GST
5.2.1(Expansion by Le Chatelier- 4031 Part 3)	-	590	ALL FEES ARE INCLUDING GST
5.2.1(Expansion by Autoclave- 4031 Part 3)	-	1118	ALL FEES ARE INCLUDING GST
5.3 a)(Setting Time Initial- 4031 Part 5)	-	590	ALL FEES ARE INCLUDING GST
5.3 b)(Setting Time Final- 4031 Part 5)	-	590	ALL FEES ARE INCLUDING GST
5.5 i)(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
5.5 ii)(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
5.5 iii)(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
4.1 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	700	-
4.1 - Table - 1 iii(Magnesia - Cl 4.8 of IS 4032:1985)	-	700	-
4.1 - Table - 1 iv(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	700	-
4.1 - Table - 1 v(Tricalcium aluminate (C3A) - Cl 4 of IS 4032:1985)	-	700	-
4.1 - Table - 1 vi(Tetracalcium alumino ferrite phase plus twice the tricalcium aluminate ( C4AF + 2C3A ) - Cl 4 of IS 4032:1985)	-	700	-
4.1 - Table - 1 vii(Total loss on ignition - Cl 4.2 of IS 4032:1985)	-	700	-

28 Nov, 2028

-
-

IS 710 (2010)

Marine plywood - Specification (Second Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1(MARKING)	-	500	-
11.2(MARKING)	-	500	-
7.1(WORKMANSHIP AND FINISH )	-	500	-
7.2(WORKMANSHIP AND FINISH )	-	500	-
7.3(WORKMANSHIP AND FINISH )	-	500	-
7.5(WORKMANSHIP AND FINISH )	-	500	-
6.1(DIMENSIONS)	-	1000	-
6.1(DIMENSIONS)	-	1000	-
6.2(DIMENSIONS)	-	1000	-
6.3(DIMENSIONS)	-	1000	-
6.3(DIMENSIONS)	-	1000	-
9.1.1(MOISTURE CONTENT)	-	1000	-
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	2000	-
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	2000	-
9.1.3 , 9.1.3.1.1(Water resistance test)	-	2000	-
9.1.3 , 9.1.3.1.2(Water resistance test)	-	2000	-
9.1.5(Mycological test)	-	2500	-
9.1.5 , 9.1.3.1.1(Mycological test)	-	2500	-
9.1.5 , 9.1.3.1.2(Mycological test)	-	2500	-
9.1.4(Tensile strength)	-	2500	-
9.1.6 (Table 3)(Static bending strength)	-	3000	-
9.1.6 (Table 3)(Static bending strength)	-	3000	-
9.1.7 (Table 4)(Wet bending strength)	-	3000	-
9.1.7 (Table 4)(Wet bending strength)	-	3000	-
9.1.8(Retention of preservative)	-	3000	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	3000	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Across the Face Grain: Average))	-	3000	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	3000	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Rupture: Along the Face Grain: Average))	-	3000	-
Cl. 9.1.7 (Table 4)(Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	3000	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Across the Face Grain: Average))	-	3000	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	3000	-
Cl. 9.1.7 (Table 4) (Cl. 9.1.7 (Table 4) (Modulus of Elasticity: Along the Face Grain: Average))	-	3000	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-	3000	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-	3000	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-	3000	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-	3000	-
Cl. 9.1.6 (Table 3)(Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-	3000	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-	3000	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-	3000	-
Cl. 9.1.6 (Table 3) (Cl. 9.1.6 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-	3000	-
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Sum of the Tensile Strength in two directions))	-	2500	-
Cl. 9.1.4 (Cl. 9.1.4 (Tensile Strength: Perpendicular to grain))	-	2500	-
Cl. 9.1.4(Cl. 9.1.4 (Tensile Strength: Parallel to grain))	-	2500	-
Cl.9.1.5,9.1.3.1.1(Cl.9.1.5 (Mycological Test),9.1.3.1.1 (Glue Shear Strength: Individual))	-	2500	-
Cl.9.1.5,9.1.3.1.1(Cl.9.1.5 (Mycological Test),9.1.3.1.1 ( Glue Shear Strength: Average))	-	2500	-
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test) , 9.1.3.1.1 (Glue Shear Strength: Individual))	-	2000	-
Cl. 9.1.3, 9.1.3.1.1 (Cl. 9.1.3 (Water Resistance Test ), 9.1.3.1.1 (Glue Shear Strength: Average))	-	2000	-
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Individual))	-	2000	-
Cl. 9.1.2, 9.1.2.1 (Cl. 9.1.2 (Glue Adhesion in Dry State), 9.1.2.1 ( Glue Shear Strength: Average ))	-	2000	-
cl.5.1(manufacture - Veneers)	-	1000	-
cl.5.1(manufacture - Veneers - moisture content)	-	1000	-
cl.5.1.1(manufacture - Veneers - Defects in Veneers)	-	1000	-
cl.5.2.2(Assembly - Thickness of Veneers)	-	1000	-
Cl-10(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	1000	-
CL-5.2.3(Joint in Veneers)	-	1000	-
CL-5.2.4(Grain Direction)	-	1000	-
CL-5.4(Moisture Content)	-	1000	-
CL-4.2.1(Adhesive)	-	1000	-

28 Nov, 2028

-
-

IS 1077 (1992)

Common burnt clay building bricks - Specification (Fifth Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Common burnt clay bricks)	-	500	-
5(General Quality)	-	500	-
6.1(Dimensions)	-	1000	-
6.2(Tolerances)	-	1000	-
7.1(Compressive strength)	-	2000	-
7.2(Water Absorption)	-	1000	-
7.3(Efflorescence)	-	1000	-
9(Marking)	-	500	-

28 Nov, 2028

-
-

IS 12894 (2002)

Pulverized fuel ash - Lime bricks - Specification

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General Requirements)	-	500	-
3.2(General Requirements)	-	500	-
3.3(General Requirements)	-	500	-
3.4(General Requirements)	-	500	-
3.5(General Requirements)	-	500	-
5.1(Dimensions)	-	500	-
7.1, Table -1(Average Wet Compressive Strength)	-	2000	-
7.2(Drying Shrinkage)	-	2000	-
7.3(Efflorescence Test)	-	1000	-
7.4(Water Absorption)	-	1000	-
5.2(Tolerance)	-	500	-
9(Marking)	-	500	-
6(Materials)	-	500	-

28 Nov, 2028

-
-

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

1100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.2.6(Spot test - Annexure L)	-	2000	-
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	2000	-
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	2000	-
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	2000	-
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	2000	-
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	2000	-
9.2.3(Adhesion of Plies - Annexure H)	-	2000	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	2000	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	2000	-
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	1000	-
7.3(Dimensional Requirements - Variation in thickness - Annexure E)	-	1000	-
7.3(Dimensional Requirements - Thickness - Annexure E)	-	1000	-
7.3(Dimensional Requirements - Width - 8.1.4)	-	1000	-
7.3(Dimensional Requirements - Length - 8.1.4)	-	1000	-
8.1.3, 6.3.3, IS 1328(Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-	1000	-
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	1000	-
9.2.6 (mechanical)(Spot test - Annexure L)	-	2000	-
cl. 11(marking)	-	1000	-
cl. 11.1(marking - BIS certification marking)	-	1000	-
Cl-10(ADDITIONAL REQUIREMENTS FOR ECO-MARK)	-	1000	-
7.3(Dimensional Requirements - Squareness - Annexure D)	-	1000	-
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	1000	-

28 Nov, 2028

-
-

IS 8042 (2015)

White portland cement - Specification (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	1000	-
5 - Table - 1 ii(Iron oxide - Cl 4.5 of IS 4032:1985)	-	1200	-
5 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1200	-
5 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	1200	-
5 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1200	-
5 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1200	-
5 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	1200	-
6 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
6 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
6 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	500	-
6 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	500	-
6-Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	500	-
6 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
6 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-
6 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
6 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
6 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
6 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	2000	-
6 -Table 2- vi(Degree of whiteness-Annex B)	-	1500	-
5 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	1000	-
5 - Table - 1 ii(Iron oxide - Cl 4.5 of IS 4032:1985)	-	1200	-
5 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1200	-
5 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	1200	-
5 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1200	-
5 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1200	-
5 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	1200	-
6 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
6 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
6 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	500	-
6 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
6-Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	500	-
6 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
6 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-
6 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
6 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
6 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
6 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	2000	-
6 -Table 2- vi(Degree of whiteness-Annex B)	-	1500	-
6, table-2, ii(Whiteness)	-	1500	-
Clause 6 Table 2, SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	1000	-
Clause 6 Table 2, SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	1000	-
Clause 6 Table 2, SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	1000	-
Clause 6 Table 2, SI No. (v) (Transverse Strength, 672 ± 4 h)	-	2000	-
Clause 6 Table 2, SI No. (v) (Transverse Strength, 168 ± 2 h)	-	2000	-
Clause 6 Table 2, SI No. (v) (Transverse Strength, 72 ± 1 h)	-	2000	-

28 Nov, 2028

-
-

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1180	ALL FEES ARE INCLUDING GST
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1118	ALL FEES ARE INCLUDING GST
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	590	ALL FEES ARE INCLUDING GST
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	590	ALL FEES ARE INCLUDING GST
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1118	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	590	ALL FEES ARE INCLUDING GST
7 -Table 2- i(Fineness 4031 Part 2)	-	1118	ALL FEES ARE INCLUDING GST

28 Nov, 2028

-
-

IS 14276 (2016)

Cement bonded particle boards - Specification (First Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Finish)	-	500	-
7(Dimensions and Tolerances)	-	500	-
8.5(Workability)	-	500	-
10.3, Table-1(Test for Density)	-	1000	-
10.5, Table-1(Test for Water Absorption)	-	1000	-
10.6, Table-1(Test for swelling in water)	-	1000	-
10.7, Table-1(Test for modulus of Rupture)	-	1000	-
10.8, Table-1(Test for modulus of Elasticity)	-	1000	-
10.9, Table-1(Test for tensile strength perpendicular to Surface)	-	2000	-
10.1, Table-1(Test for Screw Withdrawal Strength)	-	1500	-
Clause 8.2 Table 1(Moisture content)	-	1000	-

28 Nov, 2028

-
-

IS 1130 (1969)

Marble (blocks, Slabs And Tiles)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Requirements)	-	500	-
5(Sizes)	-	1000	-
6(Tolerance)	-	500	-
7.1-Table 1-(i)(Moisture absorption after 24 hours immersion in cold water)	-	1000	-
7.1-Table 1-(ii)(Hardness)	-	2000	-
7.1-Table 1-(iii)(Specific gravity)	-	1000	-
8(Workmanship)	-	500	-
9(Marking)	-	500	-

28 Nov, 2028

-
-

IS 3316 (1974)

Structural Granite

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2(General Requirements)	-	1000	-
3(Strength Requirements)	-	5000	-
4.1(Slabs)	-	500	-
4.2(Blocks for Masonry)	-	500	-
5(Marking)	-	500	-

28 Nov, 2028

-
-

IS 16415 (2015)

Composite cement - Specification

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Requirements)	-	3500	-
7(Physical Requirement)	-	7000	-
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1200	-
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	1200	-
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1200	-
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1200	-
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1200	-
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1200	-
7 and Table 3 i(Fineness IS 4031(Part 2))	-	1000	-
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	500	-
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	-
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	500	-
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	500	-
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	1000	-
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	2000	-
6 -Table - 2 i(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1200	-
6 -Table - 2 ii(Magnesia - Cl 4.8 of IS 4032:1985)	-	1200	-
6 -Table - 2 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1200	-
6 -Table - 2 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1200	-
6 -Table - 2 v(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1200	-
6 -Table - 2 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1200	-
7 and Table 3 i(Fineness IS 4031(Part 2))	-	1000	-
7 and Table 3 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	500	-
7 and Table 3 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	-
7 and Table 3 iii a(Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-	500	-
7 and Table 3 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	500	-
7 and Table 3 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	1000	-
7 and Table 3 v(Drying shrinkage IS 4031(Part 10))	-	1000	-
7 and Table 3 vi(Transverse strength (optional) IS 4031(Part 8) )	-	2000	-
Cl. 6.1,Table 2(Alkali content)	-	1200	-
Cl. 6.1,Table 2(Chloride content)	-	1200	-
Cl. 6.1,Table 2(Loss on ignition)	-	1200	-
Cl. 6.1,Table 2(Suilphide sulphur)	-	1200	-
Cl. 6.1,Table 2(Total sulphur content calculated as sulphuric anhydride)	-	1200	-
Cl. 6.1,Table 2(Magnesia)	-	1200	-
Cl. 6.1,Table 2(Insoluble residue)	-	1200	-

28 Nov, 2028

-
-

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1118	ALL FEES ARE INCLUDING GST
7 Table-3 iii b(Setting Time Final)	-	590	ALL FEES ARE INCLUDING GST
7 Table-3 iii a(Setting Time Initial)	-	590	ALL FEES ARE INCLUDING GST
7 Table-3 ii b(Expansion by Autoclave)	-	1118	ALL FEES ARE INCLUDING GST
7 Table-3 ii a(Expansion by Le Chatelier)	-	590	ALL FEES ARE INCLUDING GST
7 Table-3 i.(Fineness)	-	1118	ALL FEES ARE INCLUDING GST
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	0	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	0	-
6.1 Table-2 iii.(Insoluble residue)	-	0	-
6 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	0	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	0	-
6.1 Table-2 vi(Loss on ignition)	-	0	-
6.1 Table-2 vii(Chloride content)	-	0	-
6.1 Table-2 viii(Alkali content)	-	0	-

28 Nov, 2028

-
-

IS 455 (2015)

Portland slag cement - Specification

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table 1 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 Table 1 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 Table 1 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	1118	ALL FEES ARE INCLUDING GST
7 Table 1 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	590	ALL FEES ARE INCLUDING GST
7 Table 1 iii a(Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-	590	ALL FEES ARE INCLUDING GST
7 Table 1 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1118	ALL FEES ARE INCLUDING GST
7 Table 1 ii a(Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-	590	ALL FEES ARE INCLUDING GST
7 Table 1 i(Fineness IS 4031(Part 2))	-	1118	ALL FEES ARE INCLUDING GST
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	0	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	0	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	0	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	0	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	0	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	0	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	0	-

28 Nov, 2028

-
-

IS 4250 (1980)

Specification for domestic electric food - Mixers (Liquidizers And Grinders) (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	500	-
6(Classification- IS 302-1)	-	499.99	-
7.1(Marking- IS 302-1)	-	500	-
7.1(Marking- IS 302-1)	-	500	-
7.1(Marking- IS 302-1)	-	500	-
7.1(Marking- IS 302-1)	-	499.99	-
7.2(Marking)	-	500	-
7.4(Marking)	-	500	-
7.5(Marking)	-	500	-
7.6(Marking)	-	500	-
8( Protection Against Electric Shock, IS 302-1)	-	500	-
9(Starting, IS 302-1)	-	1000	-
10(Power Input and Current, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
11(Heating, IS 302-1)	-	1000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	1500	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	1500	-
15.1(Moisture Resistance, IS 302-1)	-	1500	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	1500	-
19(Abnormal Operation, IS 302-1)	-	1500	-
20(Stability & Mechanical Hazards, IS 302-1)	-	1500	-
21(Mechanical Strength, IS 302-1)	-	1000	-
25(Supply Connection and External Flexible Cords, IS 302-1)	-	1000	-
27(Provision for Earthing, IS 302-1)	-	1000	-
28(Screws & Connections, IS 302-1)	-	1000	-
29(Clearances and Distances through Insulation, IS 302-1)	-	1000	-
30(Resistance to Heat, Fire, Tracking, IS 302-1)	-	1500	-
22.2(Construction)	-	500	-
34.2(Operational tests- Grinding coffee (for machines which have a dry grinding arrangement))	-	2000	-
34.3(Whisking egg whites )	-	1500	-
34.4(IDLI batter-Grinding of black gram)	-	1000	-
34.4(IDLI batter-Grinding of rice)	-	1000	-
34.5.1 (a)(Operational test for juicers )	-	1000	-
37(Strength of Assembly )	-	1000	-

28 Nov, 2028

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Earthed & Unearthed upto 1.1kV and DC upto 1.5kV

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	1000	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	500	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	500	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
8.1(CONSTRUCTION : CONDUCTOR)	-	500	-
8.2(CONSTRUCTION : CONDUCTOR)	-	500	-
9.2(INSULATION : Thickness of Insulation)	-	500	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	500	-
9.4(INSULATION : Application of Insulation)	-	500	-
10.1(CORE IDENTIFICATION)	-	500	-
10.2(CORE IDENTIFICATION)	-	500	-
10.3(CORE IDENTIFICATION)	-	500	-
11.1(LAYING UP OF CORES)	-	500	-
11.2(LAYING UP OF CORES)	-	500	-
12.1(INNER SHEATH)	-	500	-
12.2(INNER SHEATH)	-	500	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	500	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	500	-
13.1.1(ARMOURING : Application)	-	500	-
13.1.2(Armouring: Coverage )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	-
13.4(ARMOURING : Joints)	-	1000	-
13.5.1(ARMOURING : Resistance)	-	1000	-
13.5.2(ARMOURING : Resistance)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(OUTER SHEATH)	-	1000	-
14.3(OUTER SHEATH : Colour )	-	1000	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	1000	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	1000	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	1000	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	1000	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	1000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 d)4)(Hot deformation : Insulation )	-	1000	-
15.1 d)4)(Hot deformation : Sheath )	-	1000	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	1000	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	1000	-
15.1 d)6)(Heat shock test- Insulation )	-	1000	-
15.1 d)7)(Thermal stability- insulation )	-	1000	-
15.1 d)7)(Thermal stability- Sheath )	-	1000	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	1000	-
15.1 e)(Insulation resistance test : IR Constant )	-	1000	-
15.1 f)(High voltage test ( water immersion test ))	-	1000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	1000	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	1000	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	1000	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1000	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	1000	-
16.4(Flammability Test)	-	1000	-
16.5(Oxygen Index Test)	-	5000	-
16.6(Flame Retardance Test on Single Cables)	-	1000	-
16.9(Test for Halogen Acid Gas Evolution)	-	5000	-
16.1(Temperature Index)	-	5000	-
Cl No. 16.10(Smoke density test)	-	5000	-
Table 4(Copper purity test)	-	1000	-
16.4(Flammability Test- Un affected portion)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1000	-

28 Nov, 2028

-
-

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

Aluminum conductors, galvanized steel reinforced

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	600	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	600	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	600	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	599.98	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	999.99	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	999.99	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	599.99	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	600	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	600	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	1000	-
13.7.2 (chem)(Mass of Zinc coating)	-	600	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	600	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	600	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	600	-
13.10 (elec)(Ultimate breaking load)	-	10000	-
13.11 (elec)(Stress-strain test)	-	10000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	600	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	600	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	600	-

28 Nov, 2028

-
-

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Al stranded Conductors & Accessories for Overhead line

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	600	-
12.3, Table-1(Breaking load before stranding)	-	1500	-
12.3, Table-1(Breaking load after stranding)	-	1500	-
12.4(Wrapping test)	-	1000	-
12.5, Table 1(Resistance test)	-	1000	-
12.6, Table 3(Measurement of lay ratio)	-	1000	-
6(Freedom from defects)	-	500	-

28 Nov, 2028

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Conductor - Material)	-	1000	-
5.1(Insulation)	-	500	-
5.2(Application )	-	500	-
12(CONSTRUCTION Core Identification)	-	500	-
4.2(Conductor resistance test)	-	500	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	500	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	500	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	500	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	500	-
Table 1 iii) c) 3)(Elongation variation)	-	500	-
Table 1 iii) c) 3)(TS variation)	-	500	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	500	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	500	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	500	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	500	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	500	-
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	500	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	500	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	500	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	500	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	500	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	500	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	500	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	500	-
10.4(Flammability test- Unaffected portion)	-	500	-
10.4(Flammability test-Burning after flame removal)	-	500	-
4.1(Annealing test (for copper))	-	500	-
4.1(Wrapping test (for Al))	-	500	-
4.1(Tensile test (for Al)- After Stranding)	-	500	-
4.1(Tensile test (for Al)-Before Stranding)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	500	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	500	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	500	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	500	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	500	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	500	-
10.5(Oxygen index)	-	5000	-
10.7(Temperature index)	-	5000	-
10.6(Halogen evolution)	-	5000	-
10.8(Smoke density rating)	-	5000	-
table 1 e) 3) (IR constant- max. Temp)	-	500	-
table 1 e) 3) (IR constant- Room temp )	-	500	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	500	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	500	-
10.1(HV (water immersion))	-	1000	-
10.1(HV (water immersion))	-	1000	-
10.2(HV (room temperature))	-	1000	-
9(Overall dimensions)	-	500	-
8.3(Minimum thickness of Sheath)	-	500	-
8.3(Avarage thickness of Sheath)	-	500	-
5.3(Minimum thickness of insulation)	-	500	-
5.3(Avarage thickness of insulation)	-	500	-
Table 4(Copper purity test)	-	2000	-

28 Nov, 2028

-
-

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	500	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	500	-
5.1(Insulation)	-	500	-
6.1(Flexibility class)	-	500	-
6.2(Compactness)	-	500	-
6.2(No of strands)	-	500	-
6.2(Surface)	-	500	-
6.3(Protective barrier)	-	100	-
6.4(size of street lighting conductor)	-	500	-
6.5(Size of messenger conductor )	-	500	-
6.6(Joints in messenger conductor )	-	500	-
6.6(Direction of outer layer)	-	500	-
7.1(Insulation)	-	500	-
7.2( Thickness of insulation)	-	1000	-
7.3(Tolerance on thickness of insulation )	-	1000	-
7.4(Aplication of the insulation )	-	1000	-
7.5(Colour of the insulation )	-	500	-
8.1(Core identification)	-	500	-
8.2(Core identification)	-	500	-
8.3(Identification by other means)	-	500	-
9.1(Assembly (Laying up))	-	500	-
9.2(Assembly (Laying up))	-	1000	-
9.3(Direction of lay)	-	500	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	1000	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	1000	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1000	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	1000	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	1000	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	1000	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	1000	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	1000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	1000	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	1000	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	1000	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	1000	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	1000	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	1000	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	1000	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1000	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	1000	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	1000	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	1000	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	1000	-
10.1 g)(High voltage test - IS10810:Part 45)	-	1000	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	1000	-

28 Nov, 2028

-
-

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Al alloy stranded conductor

5400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	600	-
7.1 Table-1(Dimensional measurement of wires)	-	600	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	600	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	600	-
9.3(Direction of Lay)	-	600	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	1000	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	1000	-
12.3 Table 1(Elongation Test- Before Stranding)	-	1000	-
12.3 Table 1(Elongation Test- After Stranding)	-	1000	-
12.4 Table 1(Resistance of Aluminium wire)	-	1000	-
9.2(Lay Ratio 24 wire layer)	-	600	-
9.2(Lay Ratio 18 wire layer)	-	600	-
9.2(Lay Ratio 12 wire layer)	-	600	-
9.2(Lay Ratio 3/6 wire layer)	-	600	-

28 Nov, 2028

-
-

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

4950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	200	-
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	200	-
6.3(Standard Mark on Conduit)	-	100	-
7.1.1(Maximum and minimum outside diameter of socket)	-	500	-
7.2(Minimum inside diameter of conduit)	-	500	-
7.1.1 Table-2(Length of Socket end)	-	500	-
7.4(Unifomity of The wall Thickness)	-	500	-
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	500	-
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	500	-
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	500	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	500	-
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	500	-
10(Resistance to Heat -Ball presure test)	-	500	-
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	500	-
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	500	-
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	500	-

28 Nov, 2028

-
-

IS 15652 (2006)

Insulating mats for electrical purposes - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	100	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	100	-
10.a)(Packing)	-	300	-
10.b)(Packing)	-	0	-
10.c)(Packing)	-	0	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	100	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	100	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	100	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	100	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	100	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	500	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	0	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	0	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	100	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	100	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	500	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	500	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	500	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	500	-
8(Thermal Properties (Cl..8.4))	-	500	-
8(Thermal Properties (Cl..8.4))	-	500	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	500	-
8(Extreme Low Temperature (Cl.8.6))	-	500	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	500	-

28 Nov, 2028

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	500	-
9.3(Thickness of Insulation - Minimum)	-	500	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	500	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	500	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.5(Armouring : Resistance Test)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	1000	-
14.2(Colour of outer sheath)	-	1000	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	500	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 e) v) (Sheath : Hot deformation)	-	1000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	1000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	500	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	500	-
16.9(Oxygen Index Test)	-	5000	-
16.14(Temperature Index)	-	5000	-
16.1(Flame Retardance Test on Single Cables)	-	5000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	5000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	500	-
15.4 (b)(Cold impact)	-	500	-
Cl No. 16.15(Smoke density test)	-	5000	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1500	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	1500	-

28 Nov, 2028

-
-

IS 12776 (2002)

Galvanized strand for earthing - Specification (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Freedom From Defects (IS 12776))	-	250	-
5.3(Joints in wires (IS 12776))	-	250	-
6- Annex-A, Sl-2(Size of the wire (IS 12776))	-	250	-
6- Annex-A, Sl-8(Lay (IS 12776))	-	250	-
8.1-Annex-A,Sl-9(Breaking Force of Strand (IS 12776))	-	1500	-
8.2-Annex-A,Sl-6(Elongation of wire, IS 10810(Part-37))	-	1500	-
8.3-Annex-A,Sl-12(Resistance at 200 C (IS 12776))	-	1500	-
8.4(Wrapping Test (IS 12776))	-	500	-
8.5-Annex-A-Sl-7a(Amount of zinc Coating (IS 6745))	-	1000	-
8.5-Annex-A-Sl-7b(Uniformity of Coating (IS 2633))	-	1000	-
8.5-Annex-A-Sl-4(Torsion Test IS 10810(Part-37))	-	500	-
8.2-Annex-A,Sl-3(Tensile Strength of wire IS 10810(Part-37))	-	1500	-

28 Nov, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

NATIONAL TEST HOUSE-SR (NTH), Chennai

GOVT.OF INDIA,CSIR ROAD,TARAMANI., Chennai, Chennai, Tamil Nadu, 600113

9444944901 director-chn@nth.gov.in

Scope List