BIS - LIMS (Laboratory Information Management System)

NATIONAL TEST HOUSE-SR (NTH), Chennai

GOVT.OF INDIA,CSIR ROAD,TARAMANI., Chennai, Chennai, Tamil Nadu, 600113

9444944901 director-chn@nth.gov.in

Scope List

Reset

56 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	800	nil
6.1(Manganese %)	-	800	nil
6.1(Phosphorus %)	-	800	nil
6.1(Sulphur %)	-	800	nil
6.1( Copper %)	-	800	nil
6.1(Silicon %)	-	800	-

28 Nov, 2028

-
-

IS 8783 : Part 4 : Sec 1 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for indmdual wires: Sec 1 HR PVC insulated wires (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3.1 (Conductor)	-	500	-
Cl.4(Material)	-	500	-
Cl.5.1.1 (Dimensions)	-	500	-
Cl 6(Resistance Test)	-	1000	-
Cl 4.1.2 (Visual examination)	-	500	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile strength )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile Strength)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation at Break )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Water absorption (Gravimetric) )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Hot deformation Test )	-	1000	-
Cl. 4 Table 1of IS: 8783 (part 2) (Heat shock Test )	-	1000	-
Cl.4.1(Insulation )	-	1000	-
Cl.4.2(Application)	-	1000	-
Cl.4.3(Colour)	-	500	-
Cl.4.4(Overall Diameter)	-	500	-
Cl.4.5(Finish)	-	500	-
Cl.4.6(High Voltage Test Water Immersion )	-	1000	-

28 Nov, 2028

-
-

IS 8783 : Part 4 : Sec 3 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for individual wires: Sec 3 polyester and polypropylene insulated winding wires (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-	100	-
6.1(The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-	100	-
6.1(a) Reference to this Indian Standard;)	-	100	-
6.1(b) Manufacturer's name,brand name or trade-mark;)	-	100	-
6.1(c) Size of conductor / maximum overall diameter,)	-	100	-
6.1(d) Length of conductor on spool / reel /coil;)	-	100	-
6.1(e) Number of lengths onspool / reel / coil (if more than one);)	-	100	-
6.1(f) Country of Manufacturer)	-	100	-
6.1(g) Year of Manufacture.)	-	100	-
6.2(BIS Certification Mark)	-	100	-
4(i) Material)	-	500	-
5(ii) Diameter [mm] Seperate wire:)	-	500	-
5(ii) Diameter [mm] Wire taken from cable:)	-	500	-
5(iii) Annealing test [Percentage] on Seperate wire:)	-	500	-
5(iii) Annealing test [Percentage] on Wire taken from cable:)	-	500	-
5(d) Resistance test [Ohm/km corrected to 20°c)	-	500	-
4.1, table 1 & 2(a) Thickness of Polyster (mm))	-	500	-
4.1, table 1 & 3(b) Thickness of Polypropylene (mm))	-	500	-
4.1, table 1 & 4(c) Total thickness of Insulation(mm))	-	500	-
4.2(Application of insulation)	-	500	-
4.3(Colour of Insuation)	-	500	-
4.4(Overall diameter (mm))	-	500	-
4(Before ageing Tensile strength [N/mm²])	-	500	-
4(Before ageing Elongation at break [Percentage])	-	500	-
4(After ageing Tensile strength [N/mm²])	-	500	-
4(Variation on tensile strangth [Percentage])	-	500	-
4(After ageing Elongation at break [Percentage])	-	500	-
4(Variation on elongation at break [Percentage])	-	500	-
4(High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-	1000	-
Clause No. 3(Insulation Resistance (Volume Resistivity at 27º C ))	-	1000	-
Clause No. 3(Insulation Resistance (Volume Resistivity at test temperature 90 º C ))	-	1000	-
Clause No. 3(Heat Shock)	-	1000	-
Clause No. 3(Shrinkage)	-	1000	-
Clause No. 3(Hot Deformation)	-	1000	-
Clause No. 3(Water absorption)	-	1000	-

28 Nov, 2028

-
-

IS 3854 (1997)

Switches for domestic and similar purposes - Specification (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Rating)	-	500	-
6(Rating)	-	500	-
7(Classification)	-	500	-
7(Classification)	-	500	-
7(Classification)	-	500	-
8(Marking)	-	500	-
8(Marking)	-	500	-
8(Marking)	-	500	-
8(Marking)	-	500	-
8(Marking)	-	500	-
10(Protection against Electric Shock)	-	1000	-
11.1(Provision for earthing)	-	500	-
12(Terminals)	-	500	-
12.2.2(Connection of conductor)	-	500	-
12.2.3(Mechanical strength of terminals)	-	500	-
12.2.4(Resistance to corrosion)	-	1000	-
12.2.5(Undue damage to conductor)	-	500	-
12.2.7(Insertion of conductor)	-	500	-
13.2(b) Construction of switch [Cl 13.2])	-	500	-
13.3(c) Covers,cover plates and actuating members [Cl 13.3])	-	500	-
14(Mechanism [Cl. 14])	-	1000	-
15.1(Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-	1000	-
16.1(Insulation resistance [Cl. 16.1])	-	1000	-
16.2( Electric Strength [Cl. 16.2])	-	1000	-
17(Temperature- rise [Cl. 17])	-	1500	-
18(Marking and breaking Capacity[Cl. 18])	-	1500	-
18(Marking and breaking Capacity[Cl. 18])	-	1500	-
19(Normal Operation [Cl. 19] a) General & Operation)	-	1000	-
20(Mechanical Strength Test [Cl. 20])	-	1000	-
21(Resistance to Heat [Cl.21])	-	1500	-
22(Screw, Current Carrying Part And Connection [Cl.22])	-	1000	-
23.2(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	500	-
23(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	1000	-
19.2(Normal Operation (For AX type Switches) [Cl. 19.2])	-	1500	-
24.1.1(Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-	1000	-
25(Resistance to Rusting)	-	1000	-

28 Nov, 2028

-
-

IS 371 (1999)

Ceiling roses - Specification (Third Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking)	-	100	-
10.1(Dimentions)	-	100	-
10.2(Dimentions)	-	100	-
10.2(Dimentions)	-	100	-
11.1(Accessibility of live parts )	-	500	-
11.2(Accessibility of live parts )	-	100	-
11.3(Accessibility of live parts )	-	100	-
11.4(Accessibility of live parts )	-	100	-
12.1(Provision for Earthing)	-	500	-
12.2(Provision for Earthing)	-	100	-
13.1(Terminals)	-	100	-
13.2(Terminals)	-	100	-
13.3(Terminals)	-	100	-
13.4(Terminals)	-	100	-
13.5(Terminals)	-	100	-
13.6(Terminals)	-	100	-
13.7(Terminals)	-	100	-
13.8.1(Terminals)	-	100	-
13.8.2(Terminals)	-	100	-
13.8.3(Terminals)	-	100	-
14.1(Construction)	-	500	-
14.2(Construction)	-	100	-
14.3(Construction)	-	100	-
14.4(Construction)	-	100	-
15.1(RESISTANCE TO MOISTURE AND HUMIDITY, INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	1000	-
15.2(RESISTANCE TO MOISTURE AND HUMIDITY, INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
15.3(RESISTANCE TO MOISTURE AND HUMIDITY, INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
15.4(RESISTANCE TO MOISTURE AND HUMIDITY, INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
15.5(RESISTANCE TO MOISTURE AND HUMIDITY, INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
15.6(RESISTANCE TO MOISTURE AND HUMIDITY, INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
15.7(RESISTANCE TO MOISTURE AND HUMIDITY, INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
16(Temperature Rise Test)	-	1000	-
17(Temperature Rise Test)	-	1000	-
18(Resistance to heat)	-	1000	-
19(Resistance to abnormal heat fire and tracking)	-	1000	-
19.3(Resistance to abnormal heat fire and tracking)	-	500	-
20.1(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
20.2(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
20.3(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
21.1(CREEPAGE DISTANCE AND CLEARANCES)	-	500	-
22.1(Resistance to Excessive residual Stress and to Rusting )	-	500	-
22.1(Resistance to Excessive residual Stress and to Rusting )	-	500	-

28 Nov, 2028

-
-

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Phosphorus %)	-	400	-
14 (b)(Marking)	-	400	-
7(Dimensions)	-	400	-
7(Dimensions)	-	400	-
7(Dimensions)	-	400	-
11(Freedom from defects)	-	400	-
9.1(Galvanizing Requirements )	-	400	-
9.2(Galvanizing Requirements )	-	400	-
9.3(Galvanizing Requirements )	-	400	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	400	-
8.2(Mechanical Properties (as per IS 1717))	-	400	-
8.3(Mechanical Properties (as per IS 1755))	-	400	-
8.4(Mechanical Properties (as perIS 10810(Part- 42)))	-	400	-
Clause 6.1, Table-1(Sulphur)	-	400	-
Clause 6.1, Table-1(Phosphorus)	-	400	-
6.2( Nitrogen%)	-	400	-
6.2(Sulphur %)	-	400	-

28 Nov, 2028

-
-

IS 14756 (2022)

Draft Indian Standard STAINLESS STEEL COOKWARE SPECIFICATION Second Revision of IS 14756

36300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material)	-	3000	-
3.2(Material)	-	3000	-
3.3(Material)	-	3000	-
3.4(Material)	-	3000	-
3.5(Material)	-	3000	-
4.1 (Annex A)(Shapes and Dimensions)	-	500	-
4.2 (Table 1)(Shapes and Dimensions)	-	1000	-
4.3(Shapes and Dimensions)	-	1000	-
4.4(Shapes and Dimensions)	-	1000	-
5.1(Workmanship and Finish)	-	200	-
5.2(Workmanship and Finish)	-	200	-
5.3(Workmanship and Finish)	-	200	-
5.6(Workmanship and Finish)	-	200	-
6.1(Staining Test)	-	2000	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	1000	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	2000	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	3000	-
6.5(Coating Thickness Test (For Copper Deposit))	-	1000	-
6.6(3 Ply)	-	3000	-
6.7.1(Nominal Capacity Test)	-	1000	-
6.8.1(Tests on Tempered Glass Lid)	-	500	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	500	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	2000	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	500	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	500	-

28 Nov, 2028

-
-

IS 17569 (2021)

Insulated Containers for Food Storage — Specification

31500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Manufacture and Workmanship)	-	500	-
7.1(Material)	-	6000	-
7.1.2(Thickness)	-	500	-
7.3(Capacity)	-	500	-
7.4(Heat Retention Capability)	-	3000	-
7.5(Cold Retention Capability)	-	3000	-
7.6.1(Drop Impact Test)	-	3000	-
7.6.2(Pendulum Impact Test)	-	1000	-
7.7(Fixing Strength of the Handle)	-	3000	-
7.8(Test for Strength of Shoulder Strap)	-	1000	-
7.9(Leakage Test)	-	2000	-
7.10(Joint Leak Test)	-	1000	-
7.11(Staining Test)	-	4000	-
7.13.1(Length of the Shoulder Strap)	-	500	-
7.13.2(Stability of Insulated Container)	-	500	-
7.13.3(Cleaning)	-	500	-
7.14(Seepage Test)	-	1000	-
9.1(Marking)	-	0	-
9.2(BIS certification marking)	-	0	-
10(Packaging)	-	0	-
"CLAUSE 7.1.2.1 "(Minimum Thickness of Outer Container)	-	500	-
5.3(Manufacture and Workmanship)	-	0	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Lead)	-	0	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Cadmium)	-	0	-
7.1.2.8(Bisphenol A(BPA))	-	0	-
7.12("Check for PUF (Polyurethane Foam) or any Other Similar Thermal Insulation Material ")	-	0	-
CLAUSE 5.2(Welding Defects)	-	0	-
CLAUSE 7.1(Materials)	-	0	-
CLAUSE 7.1.2.2(Thickness of plastic)	-	0	-
"CLAUSE 7.1.2.1 "(Coating Thickness)	-	0	-
"CLAUSE 7.1.2.1 "(Salt Water Corrosion Test)	-	0	-
CLAUSE 7.1.2.1(Adhesion Test)	-	0	-
CLAUSE 7.1.2.1(Lead Limit)	-	0	-
CLAUSE 7.1.2.1(Cadmium Limit)	-	0	-
CLAUSE 7.1.2.3(Outer container or lid - thickness)	-	0	-
CLAUSE 7.3(Capacity)	-	0	-
CLAUSE 7.4(Heat Retention Capability)	-	0	-
CLAUSE 7.5(Cold Retention Capability)	-	0	-
CLAUSE 7.6.1(Drop Impact)	-	0	-
CLAUSE 7.6.2(Pendulum Impact)	-	0	-
CLAUSE 7.7(Fixing Strength of Handle)	-	0	-
CLAUSE 7.8(Test for Strength of Shoulder Strap)	-	0	-
CLAUSE 7.9(Leakage Test)	-	0	-
CLAUSE 7.10(Joint Leak Test)	-	0	-
CLAUSE 7.11(Staining Test)	-	0	-
CLAUSE 7.12(Checking of PUF insulation)	-	0	-
CLAUSE 7.13.1(Length of the Shoulder Strap)	-	0	-
CLAUSE 7.13.2(Stability of Flask)	-	0	-
CLAUSE 7.1.1(Material - inner container)	-	0	-
C 7.1.1 Note Annex C(Test for leaching of food grade stainless steel)	-	0	-
CL 7.1.1 Note- Annex D(Sensational test method)	-	0	-
Cl 7.1.2.2(Polymer - test for BPA)	-	0	-
Cl 7.1.2.4(Silicon gasket - overall migration)	-	0	-
Cl 7.1.2.4(Silicon gasket - defects)	-	0	-
Cl 7.1.2.5(Performance requirement for glass lid - Fragmentation test (Cl 8.15.1 of IS 2347))	-	0	-
Cl 7.1.2.5(Performance requirement for glass lid - Ball drop test (Cl 8.15.2 of IS 2347))	-	0	-
Cl 7.1.2.5(Performance requirement for glass lid - Thermal shock test (Cl 8.15.3 of IS 2347))	-	0	-
Cl 7.1.2.5(Performance requirement for glass lid - Free fall test (Cl 8.15.4 of IS 2347))	-	0	-
Cl 7.1.2.5(Thickness of steel rim)	-	0	-
Cl 7.1.2.5(Thickness of glass lid)	-	0	-
Cl 7.1.2.6(Thermal insulating material)	-	0	-
Cl 7.1.2.7(Additional lid)	-	0	-
Cl 7.1.2.8(Hot/Cold Box - thickness)	-	0	-
Cl 7.1.2.9(Internal utensils- material)	-	0	-
Cl 7.1.2.9(Internal utensils- thickness)	-	0	-
Cl 7.1.2.9(Internal utensils - thickness of plastic lid)	-	0	-
Cl 7.1.2.9(Test for BPA)	-	0	-
CLAUSE 7.1.2.3(Outer container or lid - material)	-	0	-

28 Nov, 2028

-
-

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

32000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.23(There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-	2000	-
24 (Annex - E)(Combustion (CO and CO2 ratio))	-	0	-
4.1(Requirement)	-	0	-
5(Materials)	-	100	-
6(Design for Maintenance)	-	200	-
7(Rigidity and Stability)	-	500	-
8(Workmanship and Finish)	-	200	-
9(Gas Taps)	-	500	-
10(Injector Jets)	-	500	-
11(Burners)	-	500	-
12(Burner Pan Supports)	-	500	-
13.1(Gas Soundness)	-	2000	-
14(Gas Inlet Connections)	-	500	-
15(Strength and Rigidity)	-	500	-
16(General Conditions of Test)	-	0	-
17.1.1(Gas Consumption)	-	4000	-
18(Ignition and Flame Travel)	-	2000	-
19(Flame Stability)	-	500	-
20(Noise Control)	-	500	-
21(Flash Back)	-	2000	-
22(Formation of Soot)	-	2000	-
23(Resistance to Draught)	-	2000	-
24(Combustion)	-	4000	-
25(Fire Hazard and Limiting Temperature)	-	3000	-
26(Thermal Efficiency)	-	4000	-
29(Marking)	-	0	-
30(Packing)	-	0	-
Cl.24(Annexure E)(on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-	0	-
13.2(Gas Leak Detector)	-	0	-
27.1(Type Tests)	-	0	-
27.2(Routine Tests)	-	0	-

28 Nov, 2028

-
-

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3(Marking, Cl. 6.4 of IS 9537-1)	-	1000	-
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	1000	-
7.2.2(Dimensions (Maximum outside Diameter), IS 9537-2)	-	1000	-
7.3(Dimensions (Wall thickness), IS 9537-2)	-	1000	-
7.4(Screw threads, IS 9537-2)	-	0	-
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	1000	-
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	2000	-
13(External Influences, IS 9537-2)	-	2000	-

28 Nov, 2028

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

27000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.4(Load In Other Direction From Bend)	-	500	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	1180	INCLUDING 18 % GST
Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent)	-	1180	INCLUDING 18 % GST
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Carbon-IS 228)	-	1180	INCLUDING 18 % GST
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur-IS 228)	-	1180	INCLUDING 18 % GST
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Phosphorous- IS 228)	-	1180	INCLUDING 18 % GST
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	1000	-
Cl. 5.7(Bond Strength at 0.25 mm slip)	-	15000	Rs 10000/- for 8mm- 12mm, Rs 15000 for 16mm- 32mm.
Cl 7.2(Weight)	-	1000	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1000	-

28 Nov, 2028

-
-

IS 2347 (2023)

DOMESTIC PRESSURE COOKER ï¿½ SPECIFICATION

56000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Gross capacity)	-	500	-
4.2(Body Capacity)	-	0	-
5.1(Body, Lid, Containers and Grid)	-	3000	Body chemical composition
5.1.2(Body and Lid )	-	3000	Lid chemical composition
5.3(Gasket)	-	1000	-
5.4(Handles and Knobs)	-	11000	As per IS 13395
5.12(Gasket Release System)	-	0	-
8.1(Air Pressure Test )	-	1000	-
8.2(Proof Pressure Test )	-	2000	-
8.3(Operating Test for Pressure Regulating Device )	-	1000	-
8.4(Test for Safety Relief Device )	-	2000	-
8.5(Bursting Pressure Test )	-	3000	-
8.6(Test for Removal of Lid under Pressure )	-	1000	-
8.8(Composite Cooker Base )	-	8000	As per IS 15960
8.9(Aluminium induction compatible Base )	-	4000	-
8.1(Handles of cooker )	-	0	-
8.14(Ply construction cooker Body )	-	4000	-
8.17(Test for Effectiveness for Induction Bottom)	-	2000	-
11(Marking )	-	0	-
12(Packing )	-	0	-
6.1.1(Pressure Regulating Device)	-	500	-
7(Workmanship and Finish )	-	9000	As per Annex H of IS 2347
5.1.3(Stainless steel pressure cooker)	-	0	-
5.1.4(Aluminium cooker )	-	0	-
5.2(Safety Relief Device)	-	2000	-
5.5(Pressure Regulating Device )	-	2000	-
5.6(Vent Seal Pin for Pressure Regulating Device )	-	2000	-
5.7(Vent Pipe )	-	2000	-
5.8(Vent Pipe Nut )	-	2000	-
5.9(Spring )	-	2000	-
5.1(Material of Rim )	-	2000	-
5.11(Visual Pressure Indicator)	-	2000	-
6(Construction)	-	0	-
8.7(Test for Spring Loaded Mechanism )	-	0	-
8.11(External Coating)	-	4000	-
8.12(Internal Coating )	-	8000	-
8.13(Integral electrical heating)	-	0	-
8.15.1(Fragmentation Test )	-	1000	-
8.15.2(Ball Drop Test )	-	1000	-
8.15.3(Thermal Shock Test )	-	1000	-
8.15.4(Free Fall Test)	-	1000	-
4(Capacity)	-	0	-
4.2(Body Capacity)	-	0	-
5.1.1(Body, Lid, Containers and Grid)	-	0	-
5.1.2(Body, Lid, Containers and Grid)	-	0	-
5.1.3(Body, Lid, Containers and Grid)	-	0	-
5.1.4(Body, Lid, Containers and Grid)	-	0	-
5.1.5(Body, Lid, Containers and Grid)	-	0	-
5.2.1(Destructive Type Safety Relief Device)	-	0	-
5.2.2(Resettable Type Safety Relief Device)	-	0	-
5.3(Gasket)	-	0	-
5.4(Handles and Knobs)	-	0	-
5.5(Pressure Regulating Device)	-	0	-
5.6(Vent Seal Pin for Pressure Regulating Device)	-	0	-
5.7(Vent Pipe)	-	0	-
5.8(Vent Pipe Nut)	-	0	-
5.9(Spring)	-	0	-
5.10(Spring)	-	0	-
5.11(Visual Pressure Indicator)	-	0	-
5.12(Gasket Release System)	-	0	-
6(CONSTRUCTION)	-	0	-
6.1(Pressure Regulating Device)	-	0	-
6.1.1(Minimum Inside diameter of Vent Pipe.)	-	0	-
6.1.2(Pressure Regulating Device)	-	0	-
6.1.3(Pressure Regulating Device)	-	0	-
6.1.4(Pressure Regulating Device)	-	0	-
6.1.5(Pressure Regulating Device)	-	0	-
6.1.6(Pressure Regulating Device)	-	0	-
6.2(Safety Relief Device)	-	0	-
6.2.1(Safety Relief Device)	-	0	-
6.2.2(Safety Relief Device)	-	0	-
6.2.3(Safety Relief Device)	-	0	-
6.3.1(Temperature Responsive Safety Relief Device)	-	0	-
6.3.2(Temperature Responsive Safety Relief Device)	-	0	-
6.3.3(Temperature Responsive Safety Relief Device)	-	0	-
6.4.1(Handles and Knobs)	-	0	-
6.4.1.1(Handles and Knobs)	-	0	-
6.4.2(Handles and Knobs)	-	0	-
6.4.2.1(Handles and Knobs)	-	0	-
6.5(CONSTRUCTION)	-	0	-
6.6(CONSTRUCTION)	-	0	-
6.7(Internal Level Marking)	-	0	-
6.8(Internal Level Marking)	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
7.2(WORKMANSHIP AND FINISH)	-	0	-
8.17(Test for Effectiveness for Induction Bottom)	-	0	-
8.16(PRD with chain)	-	0	-
8.15.4.2(Glass lid without rim)	-	0	-
8.15.4.1("Free Fall Test ( Glass lid with rim) ")	-	0	-
8.15.3(Thermal Shock Test on Tempered Glass lid)	-	0	-
8.15.2(Ball Drop Test on Tempered Glass lid)	-	0	-
8.15.1(Fragmentation Test on Tempered Glass lid)	-	0	-
8.14(3 ply construction cooker body)	-	0	-
8.13(Pressure cooker with integral electrical heating)	-	0	-
8.12(Internal Coating)	-	0	-
7.3(WORKMANSHIP AND FINISH)	-	0	-
7.4(WORKMANSHIP AND FINISH)	-	0	-
8.1(Air Pressure Test)	-	0	-
8.2(Proof Pressure Test)	-	0	-
8.3.1(Operating Test for Pressure Regulating Device)	-	0	-
8.4.1(Test for Safety Relief Device)	-	0	-
8.4.2(Test for Safety Relief Device)	-	0	-
8.4.2 NOTE(Test for Safety Relief Device)	-	0	-
8.5(Bursting Pressure Test)	-	0	-
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	0	-
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	0	-
8.6.3(Tests for Removal of Lid under Pressure: For Cooker Fastened by Screw Clamps or Any Other Locking Device)	-	0	-
8.6.4(Tests for Removal of Lid under Pressure in case of electrical pressure cooker)	-	0	-
8.7(Test for Spring Loaded Mechanism)	-	0	-
8.8(Test for stainless steel cookers)	-	0	-
8.9("For stainless steel, aluminium induction compatible base and 3 ply cooker")	-	0	-
8.10(Testing of Handles of the cooker)	-	0	-
8.10 Note 3(Testing of Handles of the cooker)	-	0	-
8.10 Note 4(Testing of Handles of the cooker)	-	0	-
8.10 Note 5(Testing of Handles of the cooker)	-	0	-
8.10 Note 6(Testing of Handles of the cooker)	-	0	-
8.10.1(Testing of Handles of the cooker)	-	0	-
8.11.1(External Coating)	-	0	-

28 Nov, 2028

-
-

IS 13983 (1994)

Stainless Steel Sinks For Domestic Purposes

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking)	-	0	-
4(Type)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Carbon Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Silicon Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Manganese Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nickel Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Chromium Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Sulphur Content)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Phouphorous Content)	-	1000	-
6(Thickness of sheet/strip)	-	500	-
6(Depth of bowl)	-	500	-
6(Internal dimensions of the bowl)	-	500	-
6(Bowl locating limits)	-	500	-
6(Co-ordinating sizes)	-	500	-
7.1(Consruction and workmanship)	-	500	-
7.1.1(Consruction and workmanship)	-	500	-
7.2(Consruction and workmanship)	-	500	-
7.2.1(Consruction and workmanship)	-	500	-
7.3(Drainers)	-	500	-
7.4(Waste outlet)	-	500	-
7.5(Tap holes)	-	500	-
7.6(Overflows)	-	500	-
8(Finish)	-	500	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nitrogen Content)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Carbon Content)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Silicon Content)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Manganese Content)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Nickel Content)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Chromium Content)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Sulphur Content)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Phouphorous Content)	-	0	-
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Nitrogen Content)	-	0	-
5(MATERIALS)	-	0	-
6.1.1(Thickness of Sheet/Strip)	-	0	-
6.1.2(Thickness of Sheet/Strip)	-	0	-
6.2(Depth of Bowls)	-	0	-
6.3(Internal Dimensions of Bowls)	-	0	-
6.4.1(Bowl Locating Limits)	-	0	-
6.5(Coordinating Sizes)	-	0	-
7.1(CONSTRUCTION AND WORKMANSHIP)	-	0	-
7.1.1(CONSTRUCTION AND WORKMANSHIP)	-	0	-
7.2.1(CONSTRUCTION AND WORKMANSHIP)	-	0	-
7.3(CONSTRUCTION AND WORKMANSHIP)	-	0	-
7.4(Waste Outlet)	-	0	-
7.5(Tap Holes)	-	0	-
7.6(OVERFLOW)	-	0	-
Clause no. 4(types)	-	0	-
Caluse no. 5("Material -Austenitic stainless steel of Grade Designation")	-	3000	-
Clause no. 6.1(Thickness of sheet)	-	0	-
Clause no. 6.2(Depth of Bowls)	-	0	-
Clause no. 6.3(Internal dimensions of bowls)	-	0	-
Clause no. 6.4(Bowl Locating Limits)	-	0	-
Clause no. 6.5, Table No. 1(Dimension of the sink)	-	0	-
Clause no. 7(Construction and workmanship)	-	0	-
Clause no. 8(Finish)	-	0	-
Clause no. 9(Mark)	-	0	-

28 Nov, 2028

-
-

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Chemical Composition)	-	2500	Rs 4000/- with micro elements, Rs 2500/- without micro elements.
Cl 8(UTM)	-	3000	(i) Cl. 8.1, Tensile Test, Rs 3000
Cl. 8.3 Table 6(Hardness Test ( Only for CR0 & CR1))	-	2000	Included in complete test charges.
Cl. 8.2(Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-	3000	Additional charges not included in complete test charges.
Cl. 8.5 Table 5A, 5B & 5C(Plastic Strain Ratio (r bar/r-90))	-	3000	Additional charges not included in complete test charges.
Cl. 8.6 Table 5A, 5B & 5C(Tensile Strain Hardening Component (n-Value))	-	3000	Additional charges not included in complete test charges.
Cl. 8.7(Bake Hardening Index)	-	3000	Additional charges not included in complete test charges.
Cl 10(Workmanship)	-	1000	-
Cl 9(Workmanship)	-	4000	Additional charges (i) Cl. 9.3, Strain Ageing, Test Fee, Rs 3000.00, (ii) Cl. 9.5, Surface Finish, Test Fee, Rs 1000.00
Cl. 9 Table 8(Surface roughness)	-	1000	-

28 Nov, 2028

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 10.3(UTM)	-	3000	-
Cl 11.3(Press)	-	1000	-
Cl 15(Length, Width & Thickness)	-	1000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-

28 Nov, 2028

-
-

IS 277 (2018)

Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8.1(UTM)	-	3000	-
Cl 8.2(Press)	-	1000	-
Cl 14(Length, Width & Thickness)	-	1000	-
7.1 & 10.2(Mass of Coating: Single Spot Test)	-	1000	-
7.1 & 10.2(Mass of Coating: Triple Spot Test)	-	1000	-

28 Nov, 2028

-
-

IS 513 : Part 2 (2016)

Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Workmanship)	-	1000	-
Cl 7(UTM)	-	3000	-
Cl. 7.2 Table 7(Bend Test)	-	1000	-
Cl 10(Length, Width & Thickness)	-	1000	-
Cl. 7.3 Table 4A & 4B(Tensile Strain Hardening)	-	3000	Additional Charges
Cl. 8.5.3 Table 6(Surface Roughness)	-	1000	Additional Charges

28 Nov, 2028

-
-

IS/ISO 9994 (2018)

Lighters Safety specifications First Revision

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.2(Flame Height)	-	1800	-
Cl.4.3(Flame-Height adjustment)	-	600	-
Cl.4.4(Resistance to spitting or sputtering and flaring)	-	900	-
Cl.4.5(Flame Extinction)	-	1800	-
Cl.4.6(Volumetric displacement of Fuel)	-	1800	-
Cl.4.7(Mass of Fuel)	-	600	-
Cl.5.1(External Finish)	-	800	-
Cl.5.2(Compatibility of Fuel)	-	1000	-
Cl.5.3(Resistance to Fuel Loss)	-	600	-
Cl.5.4(Resistance to dropping)	-	1800	-
Cl.5.5(Resistance to elevated Temperature)	-	1800	-
Cl.5.6(Resistance to internal Pressure)	-	1800	-
Cl.5.7(Burning Behavior)	-	900	-
Cl.5.8(Resistance to cyclic burning)	-	900	-
Cl.5.9(Resistance to Continue Burning)	-	2000	-
Cl.4(Flame Generation)	-	900	-

28 Nov, 2028

-
-

IS/ISO 22702 (2018)

Utility lighters Safety specifications First Revision

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Flame generation)	-	500	-
4.2(Flame heights)	-	900	-
4.3(Flame- height adjustment)	-	400	-
4.4("Resistance to Spitting or Sputtering and flaring")	-	1800	-
4.5(Flame extinction)	-	1800	-
4.6(Volumetric Displacement)	-	1800	-
5.2(Resistance to dropping)	-	1800	-
5.3(Resistance to elevated temperature)	-	1800	-
5.4(Burning behavior)	-	900	-
5.5(Resistance to continuous burn)	-	2000	-
5.6(Resistance to cyclic burn)	-	1800	-
5.7(External Finish)	-	0	-
5.8(Compatibility with fuel)	-	1800	-
5.9(Resistance to internal pressure)	-	1800	-
6(Refilling Test)	-	900	-

28 Nov, 2028

-
-

IS 1660 (2009)

Wrought aluminium utensils - Specification (First Revision)

31100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Classification Heavy/Medium/L:ight)	-	500	-
4(Material)	-	3000	-
0.5(Fabrication)	-	0	-
5.1(The utensil shall be pressed or spun from one piece)	-	200	-
5.2( Body Thickness of the thinnest part of the finished utensil, mm Not declared )	-	500	-
5.2(Lid Thickness of the finished utensil, mm)	-	500	-
6.1 & Table 1( i) Name of Utensil )	-	0	-
6.1 & Table 1(ii) Shape of Utensil)	-	0	-
6.1 & Table 1( Nominal Size, mm)	-	200	-
6.1 & Table 1(Inside dia, Φ D mm Not declared )	-	200	-
6.1 & Table 1(Outside dia Ф NA)	-	200	-
6.1 & Table 1(Height NA)	-	200	-
6.1 & Table 1(Capacity, l NA)	-	500	-
6.1( Minimum sheet thickness for nominal size )	-	500	-
7.1(HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-	200	-
7.2(Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-	500	-
8.1(The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-	200	-
8.2(The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-	200	-
8.4.1.2( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-	500	-
8.4.2(A coating of thickness 25 to 100 microns is generally required)	-	2500	-
8.4.3(Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-	500	-
8.4.4(The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-	0	-
8.4.4(The film will appear dark grey when wet. )	-	0	-
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-	500	-
9(The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-	0	-
10(Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-	0	-
Clause 3.1.3, Table 2(Minimum Thickness at the bottom)	-	500	-
Clause 3.1.3, Table 2(Minimum Thickness of wall at top edge)	-	500	-
Clause 3.1.3, Table 2(Minimum Cover Thickness)	-	500	-
Clause 8.6.1(Performance test)	-	2000	-
Clause 8.6.2(Ground Nut Oil Test for Leakage)	-	2000	-
5.4(Qualitative and Anodized Coating)	-	2000	-
5.5(Qualitative and Anodized Coating)	-	2000	-
8.3(Anodized Coating)	-	2000	-
8.5(Plastic Coating)	-	8000	-

28 Nov, 2028

-
-

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 50 cycles)	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 25 cycles)	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 10 cycles)	-	999.98	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Cumulative Weight losses of specimen after 10, 25 & 50 cycles)	-	999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 50 cycles)	-	999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 25 cycles)	-	999.98	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 10 cycles)	-	999.98	-
Clause 7.3, Annex G(Average Breaking Load)	-	999.99	-
Clause 7.3, Annex G(Individual Breaking Load)	-	999.99	-
Clause 7.3, Annex F(Average Failure Load per unit Length)	-	999.98	-
Clause 7.3, Annex F(Individual Failure Load per unit Length)	-	999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	1999.98	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	1999.98	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	1999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	1999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	2999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	2999.97	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	2999.98	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	3000.01	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	1999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	1999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	1999.99	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	499.98	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	499.99	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	499.99	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	499.98	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	499.98	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	499.99	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	499.98	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	499.98	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	499.99	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	499.98	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	499.99	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	499.99	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	499.99	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	499.99	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	499.99	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	499.98	-
Clause 6.3 (Bonding and Delamination between the layers of paver blocks)	-	499.99	-
Clause 7.1.3 (Colour and Texture)	-	499.99	-
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	499.98	-
Clause 7.1.1 (General Quality)	-	499.98	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Lower)	-	499.99	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Lower)	-	499.98	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Higher)	-	499.98	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Higher)	-	499.98	-
Clause 3.20(Spacer nibs)	-	499.98	-
10(Marking)	-	499.98	-
cl.5(Cement)	-	0	-
5.2(Mineral Admixture)	-	0	-
5.3(Chemical Admixtures)	-	0	-
5.4(Coarse and Fine Aggregates)	-	0	-
5.5(Pigments)	-	0	-
5.6(Water)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Indivdual Compressive strength (ii))	-	1999.98	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Indivdual Compressive strength - (iii))	-	1999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Indivdual Compressive strength -(iv))	-	1999.98	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Indivdual Compressive strength - (v))	-	1999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (ii))	-	1999.98	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (iii))	-	1999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (ii))	-	1999.99	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (iii))	-	2000	-

28 Nov, 2028

-
Included w.e.f 17.06.2026

IS 15769 (2008)

Flux cored (Tubular) electrodes for gas shielded and self - Shielded metal welding of carbon or carbon - Manganese steel

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Radiographic Soundness Test)	-	1000	-
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	3000	-
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	3000	-
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	3000	-
5.6(Longitudinal Bend Test)	-	5000	-
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	5000	-
5.8 (Table No.- 15)(Chemical Composition,%)	-	5000	-
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause
5.2(Radiographic Soundness Test)	-	-	-
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	-	-
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	-	-
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	-	-
5.6(Longitudinal Bend Test)	-	-	-
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	-	-
5.8 (Table No.- 15)(Chemical Composition,%)	-	-	-
5.2(Radiographic Soundness Test)	-	-	-
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	-	-
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	-	-
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	-	-
5.6(Longitudinal Bend Test)	-	-	-
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	-	-
5.8 (Table No.- 15)(Chemical Composition,%)	-	-	-

28 Nov, 2028

-
Included w.e.f 30.07.2026

IS 9758 (1981)

Specification for flush valves and fittings for water closets and urinals

29000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 5(Manufacture & Construction)	-	2000	-
cl 6.1 to 6.3(Performance requirements)	-	9000	-
cl 7.1(Hydraulic pressure test)	-	3000	-
cl 7.2(Endurance test)	-	10000	-
cl 8(Finish)	-	5000	-
cl 5(Manufacture & Construction)	-	0	Repeat Test
cl 6.1 to 6.3(Performance requirements)	-	0	Repeat Test
cl 7.1(Hydraulic pressure test)	-	0	Repeat Test
cl 7.2(Endurance test)	-	0	Repeat Test
cl 8(Finish)	-	0	Repeat Test
cl 5(Manufacture & Construction)	-	0	Repeat Test
cl 6.1 to 6.3(Performance requirements)	-	0	Repeat Test
cl 7.1(Hydraulic pressure test)	-	0	Repeat Test
cl 7.2(Endurance test)	-	0	Repeat Test
cl 8(Finish)	-	0	Repeat Test

28 Nov, 2028

-
Included w.e.f 30.07.2026

IS 210 (2009)

Grey iron castings - Specification (First Revision)

All grades

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	1200	only phosphorus and Sulphur
7.1(WORKMANSHIP AND FINISH)	-	1000	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	1500	-
13(SIZE OF TEST BARS-Length)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	2500	-
16, Table 3(Hardness Test)	-	2000	-
17,Annex B(TRANSVERSE TEST)	-	3000	-
18(HYDROSTATIC TEST)	-	3000	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	0	-
13(SIZE OF TEST BARS-Length)	-	0	-
17,Annex B(TRANSVERSE TEST)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	0	-
16, Table 3(Hardness Test)	-	0	-
18(HYDROSTATIC TEST)	-	0	-
9(IS 7754)	-	2000	-
9(IS 7754)	-	0	-
9(Microstructure)	-	0	-
21(Marking)	-	0	-
9(Microstructure)	-	0	-
7.2(Casting dimensions)	-	0	-
Cl-6(Phosprorus (P) - IS 12308 ( P-5))	-	0	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	0	-
13(SIZE OF TEST BARS-Length)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	0	-
16, Table 3(Hardness Test)	-	0	-
17,Annex B(TRANSVERSE TEST)	-	0	-
18(HYDROSTATIC TEST)	-	0	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	0	-
13(SIZE OF TEST BARS-Length)	-	0	-
17,Annex B(TRANSVERSE TEST)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	0	-
16, Table 3(Hardness Test)	-	0	-
18(HYDROSTATIC TEST)	-	0	-
9(IS 7754)	-	0	-
9(IS 7754)	-	0	-
9(Microstructure)	-	0	-
21(Marking)	-	0	-
9(Microstructure)	-	0	-
7.2(Casting dimensions)	-	0	-
Cl-6(Phosprorus (P) - IS 12308 ( P-5))	-	0	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	0	-
13(SIZE OF TEST BARS-Length)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	0	-
16, Table 3(Hardness Test)	-	0	-
17,Annex B(TRANSVERSE TEST)	-	0	-
18(HYDROSTATIC TEST)	-	0	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	0	-
13(SIZE OF TEST BARS-Length)	-	0	-
17,Annex B(TRANSVERSE TEST)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	0	-
16, Table 3(Hardness Test)	-	0	-
18(HYDROSTATIC TEST)	-	0	-
9(IS 7754)	-	0	-
9(IS 7754)	-	0	-
9(Microstructure)	-	0	-
21(Marking)	-	0	-
9(Microstructure)	-	0	-
7.2(Casting dimensions)	-	0	-
Cl-6(Phosprorus (P) - IS 12308 ( P-5))	-	0	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	0	-
13(SIZE OF TEST BARS-Length)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	0	-
16, Table 3(Hardness Test)	-	0	-
17,Annex B(TRANSVERSE TEST)	-	0	-
18(HYDROSTATIC TEST)	-	0	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	0	-
13(SIZE OF TEST BARS-Length)	-	0	-
17,Annex B(TRANSVERSE TEST)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	0	-
16, Table 3(Hardness Test)	-	0	-
18(HYDROSTATIC TEST)	-	0	-
9(IS 7754)	-	0	-
9(IS 7754)	-	0	-
9(Microstructure)	-	0	-
21(Marking)	-	0	-
9(Microstructure)	-	0	-
7.2(Casting dimensions)	-	0	-
Cl-6(Phosprorus (P) - IS 12308 ( P-5))	-	0	-

28 Nov, 2028

-
Included w.e.f. 30.07.2026

IS 6419 (1996)

Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

All grades as per the specification, Sizes: GMAW up to 1.6mm

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Diameter)	-	500	-
6(Reels for Wire)	-	500	-
7(Reeling Condition)	-	500	-
8(Dimension of Spools, Rims & Coils)	-	1000	-
9(Lengthof Rods)	-	500	-
10.1(Finish)	-	500	-
10.1(Copper Content of Coated Wire or Rod)	-	500	-
10.2.1 Table 5(Tensile Strength-IS 1608(P-1))	-	1000	-
10.2.2 Table 6(Cast- As per Cl.10.2.2 )	-	500	-
10.2.3 Table 6(Helix- As per Cl.10.2.3 )	-	500	-
14.1 Table 7(Carbon-Relevant parts of IS 228)	-	5000	Chemical test fee Rs 5000 (includes all the elements as per the specification).
14.1 Table 7(Manganese-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Phosphorous-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Silicon-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Sulphur-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Nickel-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Chromium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Molybdenum-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Vanadium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Copper-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Titanium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Zirconium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Aluminium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Mo+Ni+Cr-Relevant parts of IS 228)	-	0	-
10.2.1(Welding rods and bare electrodes for gas shielded arc welding of structural steel)	-	2000	-
14.2(Soundness test)	-	1000	-
14.3.2(UTS)	-	1000	-
14.3.2(Yield Stress)	-	1000	-
14.3.2(% of Elongation)	-	1000	-
14.3.3(Impact Test)	-	3000	-
5(Diameter)	-	0	-
6(Reels for Wire)	-	0	-
7(Reeling Condition)	-	0	-
8(Dimension of Spools, Rims & Coils)	-	0	-
9(Lengthof Rods)	-	0	-
10.1(Finish)	-	0	-
10.1(Copper Content of Coated Wire or Rod)	-	0	-
10.2.1 Table 5(Tensile Strength-IS 1608(P-1))	-	0	-
10.2.2 Table 6(Cast- As per Cl.10.2.2 )	-	0	-
10.2.3 Table 6(Helix- As per Cl.10.2.3 )	-	0	-
14.1 Table 7(Carbon-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Manganese-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Phosphorous-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Silicon-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Sulphur-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Nickel-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Chromium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Molybdenum-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Vanadium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Copper-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Titanium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Zirconium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Aluminium-Relevant parts of IS 228)	-	0	-
14.1 Table 7(Mo+Ni+Cr-Relevant parts of IS 228)	-	0	-
10.2.1(Welding rods and bare electrodes for gas shielded arc welding of structural steel)	-	0	-
14.2(Soundness test)	-	0	-
14.3.2(UTS)	-	0	-
14.3.2(Yield Stress)	-	0	-
14.3.2(% of Elongation)	-	0	-
14.3.3(Impact Test)	-	0	-

28 Nov, 2028

-
-

IS 2185 : Part 3 (1984)

Concrete Masonry Units Part 3 Autoclaved Cellular Aerated Concrete Blocks

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Physical requirments)	-	15000	-
8.2(Physical requirments-Dimensions-Length)	-	1000	-
8.2(Physical requirments-Dimensions-Height)	-	1000	-
8.2(Physical requirments-Dimensions-Width)	-	1000	-
8.3(Physical requirments- Block density)	-	3000	-
8.4(Physical requirments- Compressive strength)	-	12000	-
8.5(Thermal Conductivity)	-	0	No test facility at present
8.6( Drying Shrinkage )	-	2000	-
8.4, 9.2 & 11.3(Indivisual Moisture Content)	-	1000	-
8.4, 9.2 & 11.3(Indivisual Bulk density)	-	1000	-
8.4, 9.2 & 11.3 & Table 1(Indivisual Compressive strength)	-	1000	-
8.3 & 9.1(Indivisual Moisture Content)	-	1000	-
8.3 & 9.1 Table 1(Indivisual Block Density)	-	1000	-
3.2 & 8.2(Indivisual Height)	-	500	-
3.2 & 8.2(Indivisual Width)	-	500	-
3.2 & 8.2(Indivisual Length)	-	500	-
8.6, 9.4 & 11.5(Grade)	-	500	-
3.4(Special Faces)	-	500	-
3.3(Faces & Arises)	-	1000	-
3.1(Shape)	-	500	-
8.1.1(General (Exposed wall construction))	-	500	-
5(MATERIALS)	-	44500	Cement Rs 10000 Flyash Rs 13500 Aggregates Rs 12000 Lime Rs 9000
7(SURFACE TEXTURE AND FINISH)	-	1000	-
9.3(Thermal Conductivity)	-	0	No facility
15(Marking)	-	500	-
8(Physical requirments)	-	15000	-
8.2(Physical requirments-Dimensions-Length)	-	1000	-
8.2(Physical requirments-Dimensions-Height)	-	1000	-
8.2(Physical requirments-Dimensions-Width)	-	1000	-
8.3(Physical requirments- Block density)	-	3000	-
8.4(Physical requirments- Compressive strength)	-	12000	-
8.5(Thermal Conductivity)	-	0	No test facility at present
8.6( Drying Shrinkage )	-	2000	-
8.4, 9.2 & 11.3(Indivisual Moisture Content)	-	1000	-
8.4, 9.2 & 11.3(Indivisual Bulk density)	-	1000	-
8.4, 9.2 & 11.3 & Table 1(Indivisual Compressive strength)	-	1000	-
8.3 & 9.1(Indivisual Moisture Content)	-	1000	-
8.3 & 9.1 Table 1(Indivisual Block Density)	-	1000	-
3.2 & 8.2(Indivisual Height)	-	500	-
3.2 & 8.2(Indivisual Width)	-	500	-
3.2 & 8.2(Indivisual Length)	-	500	-
8.6, 9.4 & 11.5(Grade)	-	500	-
3.4(Special Faces)	-	500	-
3.3(Faces & Arises)	-	1000	-
3.1(Shape)	-	500	-
8.1.1(General (Exposed wall construction))	-	500	-
5(MATERIALS)	-	44500	Cement Rs 10000 Flyash Rs 13500 Aggregates Rs 12000 Lime Rs 9000
7(SURFACE TEXTURE AND FINISH)	-	1000	-
9.3(Thermal Conductivity)	-	0	No test facility at present
15(Marking)	-	500	-
8.5(Thermal Conductivity)	-	0	No facility at present
9.3(Thermal Conductivity)	-	0	No facility at present
9.3(Thermal Conductivity)	-	0	No test facility available
8.5(Thermal Conductivity)	-	0	No test facility available at present
9.3(Thermal Conductivity)	-	0	No facility available at present

28 Nov, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

NATIONAL TEST HOUSE-SR (NTH), Chennai

GOVT.OF INDIA,CSIR ROAD,TARAMANI., Chennai, Chennai, Tamil Nadu, 600113

9444944901 director-chn@nth.gov.in

Scope List