BIS - LIMS (Laboratory Information Management System)

MSME Testing Centre, New Delhi

Shaheed Capt. Gaur Marg, Okhla Phase -III, New Delhi, South East, Delhi, 110020

9910201527 dctc-nr@dcmsme.gov.in

Scope List

Reset

47 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 12234 (2021)

Plastic equilibrium float valves for cold water services - Specification (first revision)

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Manufacture and Workmanship)	-	1000	-
7.1 to 7.3 , 7.6 to 7.9(Construction)	-	1500	-
7.4 to 7.5 and 7.10(Dimensions, Screw threads and Back nut)	-	1500	-
8.1.1, 8.1.2(Hydraulic and Shut-Off Test)	-	1000	-
8.3 Appendix-B(Flow Test)	-	1000	-
8.4 Appendix-C(Endurance Test)	-	10000	-
10(Marking)	-	1000	-
8.2 Appendix-A(Antisiphonage Test)	-	2000	-

31 Dec, 2026

-
Included w.e.f. 02.03.2026 Exclusion: 5 (Materials)

IS 9763 (2000)

Plastics Bib Taps, Pillar Taps, Angle Valves and Stop Valves for Hot and Cold Water Services -

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl. 5)(Nominal Size)	-	300	-
(Cl. 7)(Identification)	-	300	-
(Cl. 7)(Identification)	-	300	-
(Cl 8)(Construction,Workmanship and Finish)	-	300	-
(Cl 8)(Construction,Workmanship and Finish)	-	300	-
(Cl 8)(Construction,Workmanship and Finish)	-	300	-
(Cl 8.4)(Minimum Thickness)	-	300	-
(Cl. 8.5)(Finish)	-	300	-
(Cl 9.1)(Resistance to Residual Chlorine in Water)	-	500	-
(Cl 9.2)(Drip Proofness Test)	-	1500	-
(Cl 9.3)(Thermal Shock Test )	-	500	-
(Cl 9.4)(Hydraulic Pressure Test)	-	1500	-
(Cl 9.5)(Mechanical Strength Characteristics)	-	1500	-
(Cl.6 , Table 3)(Dimensions)	-	1800	-

31 Dec, 2026

-
-

IS 4246 (2025)

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION (Sixth Revision )

16100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General - IS 4246 : 2025)	-	300	-
4.1.1(General - IS 4246 : 2025)	-	300	-
5(Materials - Cl. 5 of IS 5116)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1(Materials - IS 5116)	-	300	-
5.2(Materials - IS 5116)	-	300	-
5.3(Materials - IS 5116)	-	300	-
5.5(Materials - IS 5116)	-	300	-
5.7(Materials - IS 5116)	-	300	-
6.1(Design for Maintainance)	-	300	-
6.3(Design for Maintainance)	-	300	-
6.4(Design for Maintainance)	-	300	-
6.5(Design for Maintainance)	-	300	-
6.6(Design for Maintainance)	-	300	-
7.0(Rigidity and Stability)	-	300	-
7.2(Rigidity and Stability)	-	300	-
7.3(Rigidity and Stability)	-	300	-
7.1(Rigidity and Stability)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.2(Workmanship and Finish -)	-	300	-
8.3(Workmanship and Finish -)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
11.2(Burners)	-	300	-
11.3(Burners)	-	300	-
11.4(Burners)	-	300	-
12.1(Burner Pan Support)	-	300	-
12.2(Burner Pan Support)	-	300	-
12.3(Burner Pan Support)	-	300	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	300	-
13.2(Gas Leak Detector)	-	300	-
14.2(Gas Inlet Connection)	-	300	-
14.3(Gas Inlet Connection)	-	300	-
14.4(Gas Inlet Connection)	-	300	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	300	-
14.6(Gas Inlet Connection)	-	300	-
15.0(Strength and Rigidity)	-	300	-
17.2(Gas Consumption Test - For Gas Stoves)	-	1500	-
17.3(Gas Consumption Test - For Built in Hobs)	-	1500	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	1500	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	1500	-
18.1(Ignition and Flame Travel)	-	300	-
19.1(Flame Stability)	-	300	-
19.2(Flame Stability)	-	300	-
19.3(Flame Stability)	-	300	-
20(Noise Control)	-	300	-
21(Flash Back)	-	300	-
22(Formation of Soot)	-	300	-
23(Resistance to Draught)	-	300	-
24.1(Combustion)	-	1500	-
25.2(Fire Hazard and Limiting Temperatures)	-	300	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
4.1(General - IS 4246 : 2025)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1(Materials - IS 5116)	-	300	-
5.1.1(Materials - IS 5116)	-	300	-
5.1.1(Materials - IS 5116)	-	300	-
5.2(Materials - IS 5116)	-	300	-
5.5(Materials - IS 5116)	-	300	-
5.5(Materials - IS 5116)	-	300	-
6.1(Design for Maintainance)	-	300	-
6.2(Design for Maintainance)	-	300	-
6.2(Design for Maintainance)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
13,2(Gas Soundness Test)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.2(Gas Inlet Connection)	-	300	-
14.2(Gas Inlet Connection)	-	300	-
14.2(Gas Inlet Connection)	-	300	-
15.0(Strength and Rigidity)	-	300	-
15.0(Strength and Rigidity)	-	300	-
15.0(Strength and Rigidity)	-	300	-
17.0(Gas Consumption Test)	-	1500	-
17.0(Gas Consumption Test)	-	1500	-
17.0(Gas Consumption Test)	-	1500	-
17.0(Gas Consumption Test)	-	1500	-
17.0(Gas Consumption Test)	-	1500	-
17.0(Gas Consumption Test)	-	1500	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	1500	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	1500	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	1500	-
18.1(Ignition and Flame Travel)	-	300	-
18.2(Ignition and Flame Travel)	-	300	-
18.3(Ignition and Flame Travel)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
19.1.1(Flame Stability)	-	300	-
24.1(Combustion)	-	1500	-
24.2(Combustion)	-	1500	-
25.1(Fire Hazard and Limiting Temperatures)	-	300	-
25.1(Fire Hazard and Limiting Temperatures)	-	300	-
25.1(Fire Hazard and Limiting Temperatures)	-	300	-
25.1(Fire Hazard and Limiting Temperatures)	-	300	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
4.1(General - IS 4246 : 2025)	-	300	-
4.1.1(General - IS 4246 : 2025)	-	300	-
5(Materials - Cl. 5 of IS 5116)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1(Materials - IS 5116)	-	300	-
5.2(Materials - IS 5116)	-	300	-
5.3(Materials - IS 5116)	-	300	-
5.5(Materials - IS 5116)	-	300	-
5.7(Materials - IS 5116)	-	300	-
6.1(Design for Maintainance)	-	300	-
6.3(Design for Maintainance)	-	300	-
6.4(Design for Maintainance)	-	300	-
6.5(Design for Maintainance)	-	300	-
6.6(Design for Maintainance)	-	300	-
7.0(Rigidity and Stability)	-	300	-
7.2(Rigidity and Stability)	-	300	-
7.3(Rigidity and Stability)	-	300	-
7.1(Rigidity and Stability)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.2(Workmanship and Finish -)	-	300	-
8.3(Workmanship and Finish -)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
11.2(Burners)	-	300	-
11.3(Burners)	-	300	-
11.4(Burners)	-	300	-
12.1(Burner Pan Support)	-	300	-
12.2(Burner Pan Support)	-	300	-
12.3(Burner Pan Support)	-	300	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	300	-
13.2(Gas Leak Detector)	-	300	-
14.2(Gas Inlet Connection)	-	300	-
14.3(Gas Inlet Connection)	-	300	-
14.4(Gas Inlet Connection)	-	300	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	300	-
14.6(Gas Inlet Connection)	-	300	-
15.0(Strength and Rigidity)	-	300	-
17.2(Gas Consumption Test - For Gas Stoves)	-	300	-
17.3(Gas Consumption Test - For Built in Hobs)	-	300	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	300	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	300	-
18.1(Ignition and Flame Travel)	-	300	-
19.1(Flame Stability)	-	300	-
19.2(Flame Stability)	-	300	-
19.3(Flame Stability)	-	300	-
20(Noise Control)	-	300	-
21(Flash Back)	-	300	-
22(Formation of Soot)	-	300	-
23(Resistance to Draught)	-	300	-
24.1(Combustion)	-	300	-
25.2(Fire Hazard and Limiting Temperatures)	-	1000	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
4.1(General - IS 4246 : 2025)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1.1(Materials - Toughened glass, if provided,)	-	300	-
5.1(Materials - IS 5116)	-	300	-
5.1.1(Materials - IS 5116)	-	300	-
5.1.1(Materials - IS 5116)	-	300	-
5.2(Materials - IS 5116)	-	300	-
5.5(Materials - IS 5116)	-	300	-
5.5(Materials - IS 5116)	-	300	-
6.1(Design for Maintainance)	-	300	-
6.2(Design for Maintainance)	-	300	-
6.2(Design for Maintainance)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
10(Injector Jets)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
11.1(Burners- Cl. 10 of IS 5116)	-	300	-
13,2(Gas Soundness Test)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	300	-
14.2(Gas Inlet Connection)	-	300	-
14.2(Gas Inlet Connection)	-	300	-
14.2(Gas Inlet Connection)	-	300	-
15.0(Strength and Rigidity)	-	300	-
15.0(Strength and Rigidity)	-	300	-
15.0(Strength and Rigidity)	-	300	-
17.0(Gas Consumption Test)	-	300	-
17.0(Gas Consumption Test)	-	300	-
17.0(Gas Consumption Test)	-	300	-
17.0(Gas Consumption Test)	-	300	-
17.0(Gas Consumption Test)	-	300	-
17.0(Gas Consumption Test)	-	300	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	300	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	300	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	300	-
18.1(Ignition and Flame Travel)	-	300	-
18.2(Ignition and Flame Travel)	-	300	-
18.3(Ignition and Flame Travel)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	300	-
19.1.1(Flame Stability)	-	300	-
24.1(Combustion)	-	300	-
24.2(Combustion)	-	300	-
25.1(Fire Hazard and Limiting Temperatures)	-	1000	-
25.1(Fire Hazard and Limiting Temperatures)	-	1000	-
25.1(Fire Hazard and Limiting Temperatures)	-	1000	-
25.1(Fire Hazard and Limiting Temperatures)	-	1000	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.1(Thermal Efficiency- Gas Stoves)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	3000	-

31 Dec, 2026

-
included w.e.f 24.02.2026

IS 15558 (2024)

INSTANTANEOUS DOMESTIC WATER HEATER FOR USE WITH LPG SPECIFICATION First Revision of IS 15558

15600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirements)	-	300	-
Cl-5.1(water heater)	-	300	-
Cl-5.2(copper and copper alloy)	-	1000	-
Cl-5.3(Non-metallic materials)	-	1000	-
Cl-5.4(Mixing tube and burner head)	-	300	-
Cl-6.3(All Water connections)	-	300	-
Cl-6.4(water inlet and outlet connections)	-	300	-
Cl-6.6(Gas Inlet Connections)	-	300	-
Cl-7(Flame visibility)	-	300	-
Cl-8(Gas Taps)	-	300	-
Cl-9(Flame failuse device)	-	300	-
Cl-11(Protection against accidental overheating)	-	1000	-
Cl-13(General condition of test)	-	300	-
Cl-14(Gas Soundness)	-	300	-
Cl-15(Water Soundness)	-	300	-
Cl-16(Thermal efficiency)	-	1000	-
Cl-17(carbon monoxide/carbon dioxide)	-	300	-
Cl-18(Gas Consumption)	-	300	-
Cl-19(Ignition and flame travel)	-	300	-
Cl-20(FLAME STABILITY)	-	300	-
Cl-21(NOISE CONTROL)	-	300	-
Cl-22(FLASH-BACK)	-	300	-
Cl-24("FIRE HAZARDS AND LIMITING TEMPERATURE")	-	1000	-
Cl-25(TIME FOR TEMPERATURE RISE)	-	1000	-
Cl-26(HOT WATER OUTPUT TEST)	-	1000	-

31 Dec, 2026

-
Included w.e.f.08.09.2025

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

16100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.24(Annexure E)(on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-	300	-
Cl.23(There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-	300	-
4.1(Requirement)	-	300	-
5(Materials)	-	2500	-
6(Design for Maintenance)	-	300	-
7(Rigidity and Stability)	-	300	-
8(Workmanship and Finish)	-	300	-
9(Gas Taps)	-	2400	-
10(Injector Jets)	-	1500	-
11(Burners)	-	300	-
12(Burner Pan Supports)	-	300	-
13.1(Gas Soundness)	-	300	-
14(Gas Inlet Connections)	-	2100	-
15(Strength and Rigidity)	-	300	-
17.1.1(Gas Consumption)	-	300	-
18(Ignition and Flame Travel)	-	300	-
19(Flame Stability)	-	300	-
20(Noise Control)	-	300	-
21(Flash Back)	-	300	-
22(Formation of Soot)	-	300	-
23(Resistance to Draught)	-	300	-
25(Fire Hazard and Limiting Temperature)	-	1000	-
26(Thermal Efficiency)	-	3000	-
5.1.2(Toughened glass- Adhesive tape)	-	300	-
5.1.3(Thermal Shock test)	-	300	-

31 Dec, 2026

-
-

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

15602 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1.1, table1 of IS 1239(Part1)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	4895	Chemical Composition
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	1386	Uniformity and Mass of Zinc coating
Cl 8(Outer Diameter, Thickness & Mass)	-	1676	-
Cl. 14.1(Tensile Strength)	-	1790	-
Cl. 14.1.1(Elongation)	-	1790	-
Cl. 14.2(Bend Test (uto and including 50 mm NB))	-	1790	-
Cl. 14.3(Flattening test (Over 50 mm NB))	-	1525	-
Cl. 15(Workmanship)	-	520	-
cl.17(MARKING)	-	520	-

31 Dec, 2026

-
-

IS 374 (2019)

Specification for electric ceiling type fans and regulators (Third Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017))	-	2500	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	3000	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	4000	-
9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017))	-	2000	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	4000	-
9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017))	-	4000	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	2000	-
9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017))	-	5000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	2000	-
9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017))	-	2000	-
9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017))	-	2000	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	2500	-
9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017))	-	4000	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	2500	-
9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017))	-	2500	-
9(Construction (as per Cl.22.101 of IS 302-2-80 :2017))	-	2000	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	1000	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	2000	-
9(Components (as per Cl.24.103 of IS 302-2-80 :2017))	-	2000	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	2000	-
14.3 & Table 1(Test for Air Performance)	-	4500	-
11.1(Starting)	-	1000	-
11.2(Starting)	-	1000	-
12(Interchangeability)	-	1000	-
14.4(Measurement of Speed of the Fan )	-	2000	-
14.5(Measurement of Power factor and Power Input)	-	2000	-
17(Test for Harmonic Distortion)	-	3000	-
10.1(Speed Regulators)	-	2000	-
8.1(Marking (as per Cl. 7 of IS 302-2-80:2017))	-	1000	-
8.1,a(Marking )	-	1000	-
8.1,b(Marking )	-	1000	-
8.1,c(Marking )	-	1000	-
8.1,d(Marking )	-	1000	-
8.1,e(Marking )	-	1000	-
8.1,f(Marking )	-	1000	-
8.1,g(Marking )	-	1000	-
8.2(Marking )	-	1000	-
8.3,a(Marking )	-	1000	-
8.3,b(Marking )	-	1000	-
8.3,c(Marking )	-	1000	-
8.3,d(Marking )	-	1000	-
8.3,e(Marking )	-	1000	-
8.4(Marking )	-	1000	-
8(Marking (as per Cl. 7.1 of IS 302-2-80:2017))	-	1000	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008))	-	1000	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008))	-	1000	-
8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017))	-	1000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	3000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	3000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	3000	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	1000	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	1000	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	1000	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	4000	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	2000	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	2000	-
6.2(Rating)	-	1000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	2000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	2000	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	2000	-
9(Components (as per Cl.24.104 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	2000	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	2500	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	2500	-
10.2(Speed Regulators)	-	2000	-
10.2(Speed Regulators)	-	2000	-
10.2(Speed Regulators)	-	2000	-
10.3(Speed Regulators)	-	2000	-
10.4(Speed Regulators)	-	2000	-
10.5(Speed Regulators)	-	2000	-
10.6(Speed Regulators)	-	2000	-
10.7(Speed Regulators)	-	2000	-
10.7(Speed Regulators)	-	2000	-
10.8(Speed Regulators)	-	2000	-
14.3 & Table 1(Test for Air Performance)	-	4500	-
16(Endurance Test)	-	4000	-
16(Endurance Test)	-	4000	-
16(Endurance Test)	-	4000	-
14.5(Measurement of Power factor and Power Input)	-	2000	-
16(Endurance Test)	-	4000	-
16(Endurance Test)	-	4000	-

31 Dec, 2026

-
Excl: Cl.19.11.4.1 to Cl.19.11.4.7 (EMI/EMC Test)

IS 2312 (1967)

Specification for propeller type AC ventilating fans (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Sizes )	-	2000	NA
10.1(Starting )	-	2000	-
14.2 & 15.1(Air Delivery)	-	4500	-
14.3.A(Temperature-Rise (for motors))	-	3000	-
14.1 & 14.6(Power factor)	-	2000	-
14.7(ac leakage)	-	4000	-
14.8(High voltage test)	-	4000	-
14.9(Insulation-Resistance)	-	2000	-
14.1(Earthing continuity)	-	2000	-
14.11 & 15.1(Electrical Input)	-	2500	-
14.12 & 16(Fan Speed)	-	2000	-
13.1(Marking)	-	2000	-
13.1 (a)(Marking)	-	2000	-
13.1 (b)(Marking)	-	2000	-
13.1 (c)(Marking)	-	2000	-
13.1 (d)(Marking)	-	2000	-
13.1 (e)(Marking)	-	2000	-
13.1 (f)(Marking)	-	2000	-
13.1 (h)(Marking)	-	2000	-
13.1 (j)(Marking)	-	2000	-
13.2(Marking)	-	2000	-
13.4(Marking)	-	2000	-
4.1(Rated Voltage)	-	1000	-
5.1(Rated frequency)	-	1000	-
6.1(Design and General Construction)	-	1000	-
6.3(Design and General Construction)	-	1000	-
6.3(Design and General Construction)	-	1000	-
6.4(Design and General Construction)	-	1000	-
6.5(Design and General Construction)	-	1000	-
6.6(Design and General Construction)	-	1000	-
6.7(Design and General Construction)	-	1000	-
6.9(Design and General Construction)	-	1000	-
6.1(Design and General Construction)	-	1000	-
6.11(Design and General Construction)	-	1000	-
6.12(Design and General Construction)	-	1000	-
7.1(Design and General Construction)	-	1000	-
8.1(Design and General Construction)	-	1000	-
11.1(Interchangeability)	-	2000	-
14.3(Temperature-Rise)	-	3000	-
14.3.A(Temperature-Rise (for motors))	-	3000	-
14.3.B(Temperature-Rise (for regulators))	-	3000	-
14.3.B(Moistureproofness (for regulators only))	-	4000	-

31 Dec, 2026

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl.16.1) (Cl.19.1)(Conductor)	-	2000	50% for Additional Core
4.1(Wrapping test (for Al))	-	2000	50% for Additional Core
4.2(Conductor resistance test)	-	2000	50% for Additional Core
Table 1 iii) d) 8)(Cold bend for sheath)	-	4000	50% for Additional Core
Table 1 iii) c) 9)(Cold impact for insulation)	-	4000	50% for Additional Core
10.8(Smoke density rating)	-	10000	50% for Additional Core
10.5(Oxygen index)	-	10000	50% for Additional Core
10.7(Temperature index)	-	10000	50% for Additional Core
4.1(Tensile test (for Al)- After Stranding)	-	2200	50% for Additional Core
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	5000	50% for Additional Core
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	5000	50% for Additional Core
Table 1 iii) d) 5)(Heat shock-Sheath )	-	2000	50% for Additional Core
10.2(HV (room temperature))	-	4000	50% for Additional Core
5.3(Minimum thickness of insulation)	-	1400	50% for Additional Core
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	2300	50% for Additional Core
table 1 e) 3) (IR constant- Room temp )	-	3300	50% for Additional Core
10.6(Halogen evolution)	-	7500	50% for Additional Core
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	1800	SHEATH
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	1800	50% for Additional Core
9(Overall dimensions)	-	1400	50% for Additional Core
5.3(Avarage thickness of insulation)	-	1400	50% for Additional Core
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	3200	50% for Additional Core
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	1200	SHEATH
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	1200	50% for Additional Core
10.1(HV (water immersion))	-	4200	50% for Additional Core
10.1(HV (water immersion))	-	4200	50% for Additional Core
Table 1 iii) c) 5)(Heat shock-Insulation )	-	1200	50% for Additional Core
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	1400	50% for Additional Core
table 1 e) 3) (Volume Resistivity - Room temp )	-	3300	50% for Additional Core
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	3300	50% for Additional Core
table 1 e) 3) (IR constant- max. Temp)	-	3300	50% for Additional Core

31 Dec, 2026

-
-

IS 369 (2019)

Household electric direct - Acting room heaters - Performance requirements (Fourth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.8 of IS 302-2-30:2007 &IS:302-1:2008(Protection Against Access to Live Parts)	-	2500	-
Cl.10 of IS 302-2-30:2007 &IS:302-1:2008(Power Input and Current)	-	2500	-
Cl.13 of IS 302-2-30:2007 &IS:302-1:2008(Leakage Current & Electric Strength at operating temp)	-	4000	-
Cl.14 of IS 302-2-30:2007 &IS:302-1:2008(Transient Over Voltages)	-	2000	-
Cl.15 of IS 302-2-30:2007 &IS:302-1:2008(Moisture Resistance)	-	4000	-
Cl.19 of IS 302-2-30:2007 &IS:302-1:2008(Abnormal Operation)	-	2000	-
Cl.21 of IS 302-2-30:2007 &IS:302-1:2008(Mechanical Strength)	-	2000	-
Cl.25 of IS 302-2-30:2007 &IS:302-1:2008(Supply Connection and External Flexible Cords )	-	2000	-
Cl.27 of IS 302-2-30:2007 &IS:302-1:2008(Provision for Earthing)	-	2000	-
Cl.30 of IS 302-2-30:2007 &IS:302-1:2008(Resistance to Heat and Fire.)	-	4000	-
Cl.31 of IS 302-2-30:2007 &IS:302-1:2008(Resistance to Rusting)	-	2500	-
Cl.20 of IS 302-2-30:2007 &IS:302-1:2008(Stability & Mechanical Hazards)	-	5000	-
Cl.26 of IS 302-2-30:2007 &IS:302-1:2008(Terminal for External Conductors)	-	2000	-
Cl.28 of IS 302-2-30:2007 &IS:302-1:2008(Screws and Connections)	-	2000	-
Cl.29 of IS 302-2-30:2007 &IS:302-1:2008(Clearances, Creepage Distances and Solid Insulation.)	-	2500	-
Cl.7 of IS 369:2019(Dimensions)	-	5000	-
Cl.11 of IS 302-2-30:2007 &IS:302-1:2008(Heating)	-	5200	-
Cl.16 of IS 302-2-30:2007 &IS:302-1:2008(Leakage Current & Electric Strength )	-	2900	-
Cl.18 of IS 302-2-30:2007 (Endurance)	-	6000	-
Cl.22 of IS 302-2-30:2007 &IS:302-1:2008(Construction)	-	1900	-
Cl.23 of IS 302-2-30:2007 &IS:302-1:2008(Internal Wiring)	-	1900	-
Cl.24 of IS 302-2-30:2007 &IS:302-1:2008(Component)	-	1900	-
Cl.6 of IS 302-2-30:2007(Classification)	-	1100	1.If , the samples received only for declaration of classification testing fees is Rs. 1100/-
Cl.7 of IS 302-2-30:2007 &IS:302-1:2008(Marking and Instructions)	-	1900	Rs. 1900-/ Cover all Clause 7 of all marking parameters.
Cl.10 of IS 369:2019(Warming-up time of the heater)	-	1900	-

31 Dec, 2026

-
-

IS 302 : Part 2 : Sec 35 (2017)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 35 electric instantaneous water heaters (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.8(Verification)	-	2500	-
Cl.10(Verification)	-	2500	-
Cl.11(Verification)	-	3000	-
Cl.13(Verification)	-	4000	-
Cl.14(Verification)	-	2000	-
Cl.15(Verification)	-	4000	-
Cl. 16(Verification)	-	4000	-
Cl.19(Verification)	-	4000	-
Cl.22(Verification)	-	2000	-
Cl.25(Verification)	-	2000	-
Cl.26(Verification)	-	2000	-
Cl.27(Verification)	-	2000	-
Cl.28(Verification)	-	2000	-
CL.29(Verification)	-	2500	-
Cl.30(Verification)	-	4000	-
Cl.31(Verification)	-	2500	-
Cl.17(Verification)	-	2100	Overload protection of transformers and associated circuits
Cl.20(Verification)	-	1900	Stability and mechanical hazards
Cl.21(Verification)	-	1900	Mechanical strength
Cl.23(Verification)	-	1900	Internal wiring
Cl.24(Verification)	-	1900	Components
Cl.32(Verification)	-	2200	Radiation, toxicity and similar hazards

31 Dec, 2026

-
Excl: Cl. 19.11.4.1 to Cl. 19.11.4.7 (EMI/EMC tests)

IS 7532 (2018)

Soft soap - Specification (First RevisIon)

11950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CL 5 ( 5.1)(The material shall be homogeneous translucent mass of jelly-like texture, free from putrescent, fishy or objectionable odour. It applies to soft soap with potassium or sodium base or a mixture of these bases. It does not apply to soaps for medicinal purposes. It may or may not be suitably perfumed subject to agreement between the purchaser and the supplier. It shall be free from foreign matter and visible impurities)	-	500	-
5.2(5.2 The material shall quickly form a satisfactory lather while in use and shall show no sign of any deterioration on storage in original sealed containers under normal conditions for a period of 12 months.)	-	5000	-
5.3(The soap shall not become liquid at 32°C, and no liquid shall separate when the soap is maintained at 0°C, for 24 h.)	-	1000	-
5.4(Soft soap is liable to lose moisture on keeping. The results obtained for unsaponified and unsaponifiable matter, total free alkali and free caustic alkali by the specific methods of analysis shall, therefore, be recalculated in relation to the specified minimum total fatty matter by means of the equation: Recalculated result = Minimum specified total fatty matter content Actualresult× Actual total fatty matter conten)	-	0	-
Table-1 (i) IS.no 286(Total Fatty Matter ( Type 1 ))	-	1350	-
Table-1 (ii) IS.no 286 CL 12(Unsaponified and Unsaponified matter (Type 1 ))	-	1050	-
Table-1 (iii) IS.no 286 CL 14(Rosin acids percent by mass of total fatty matter ( Type 1))	-	1050	-
Table-1 (iv) IS.no 286 Annex A(Total free alkali ( as K2O ) type 1)	-	950	-
4.5, Table-1 (v) Type-1 & Type-2(Free caustic alkali (as K2O), IS 286)	-	950	-
4.1(Description, IS 7532)	-	300	-

31 Dec, 2026

-
-

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

8574 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3795	Chemical Composition Test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	1117	Dimension and Weight
Cl. 10.7, Fig 5(Total twist, V)	-	1352	Straightness and Twist
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	1790	Tensile, Yield Strength and Elongation Test

31 Dec, 2026

-
-

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

14934 View breakup
Rs.14934/- (10% concession for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5.1, Table-3( CARBON)	-	4895	-
Cl 6(Outer Diameter, Thickness & Mass)	-	1676	-
Cl 7(Workmanship)	-	520	-
8 AND AS PER IS 4736(MASS OF ZINC COATING)	-	1386	Uniformity and Mass of Zinc coating
Cl 9(Workmanship)	-	1352	Straighness
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	1790	Tensile Test
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	1790	Cold Bend or Flattening Test

31 Dec, 2026

-
Upto 50NB only

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

3900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 Tables 2 to 9(Types)	-	300	-
5.1 Tables 2 to 9 (2)(Size of Hinge)	-	300	-
5.1 Tables 2 to 9 (3)(Length A)	-	300	-
5.1 Tables 2 to 9 (4)(Breadth B)	-	300	-
5.1 Tables 2 to 9 (4)(Breadth B1)	-	300	-
5.1 Tables 2 to 9 (4)(Breadth B2)	-	300	-
5.1 Tables 2 to 9 (5)(Thickness of Flap C)	-	300	-
5.1 Tables 2 to 9 (6)(Diameter of Hinge Pin D)	-	300	-
5.1 Tables 2 to 9 (7)(Number of Knuckles)	-	300	-
5.1 Tables 2 to 9 (8)(Number of Screw Holes)	-	300	-
5.1 Tables 2 to 9 (9)(Holes for Screw No.)	-	300	-
6.1(General)	-	300	-
6.1(General)	-	300	-
6.1(General)	-	300	-
6.2.1(Knuckles)	-	300	-
6.3(Pins)	-	300	-
6.4(Screw Holes)	-	300	-
6.4.2(Position of Holes)	-	300	-
6.4.2(X)	-	300	-
6.4.2(Y)	-	300	-
6.4.2(Z)	-	300	-
6.4.2.1(Position of Holes)	-	300	-

31 Dec, 2026

-
-

IS 2082 (2018)

Stationary storage type electric water heaters - Specification (Fifth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl.8 of IS 302-2-21:2011)(Protection Against Access to Live Parts)	-	2500	-
(Cl.10 of IS 302-2-21: 2011)(Power Input & Current)	-	2500	-
(Cl.11 of 302-2-21:2011)(Heating)	-	3000	-
(Cl.13 of IS 302-2-21:2011)(Leakage Current )	-	4000	-
(Cl.14ofIS302-2-21:2011)(Transient Over Voltages)	-	2000	-
(Cl.15 of IS 302-2-21-2011)(Moisture Resistance)	-	4000	-
Cl.16 of IS 302-2-21-2018(Leakage current and Electric strength (After humidity): Leakage current )	-	4000	-
(Cl.19 of IS 302-2-21:2011)(Abnormal Operation)	-	2000	-
(Cl.21ofIS302-2-21:2011)(Mechanical strength)	-	2000	-
(Cl.25 of IS 302-2-21:2011)(Supply Connection & External Flexible Cords)	-	2000	-
(Cl.26 of IS 302-2-21: 2011)(Terminals for External Conductors)	-	2000	-
(Cl.27 of IS 302-2-21:2011)(Provision for Earthing)	-	2000	-
(Cl.28 of IS 302-2-21:2011)(Screws & Connections)	-	2000	-
(Cl.30 of IS 302-2-21:2011)(Resistance to Heat & Fire)	-	4000	-
Cl.31 of IS 302-2-21:2018(Resistance to Rusting)	-	2500	-
(Cl.29ofIS302-2-21:2011)(Clearances, Creepage Distances and Solid Insulation)	-	25000	-

31 Dec, 2026

-
Excl: Cl.19.11.4.1 to Cl.19.11.4.7 (EMI/EMC Test)

IS 302 : Part 2 : Sec 21 (2018)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 21 stationary storage type electric water heaters (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0(Protection against access to live parts)	-	2500	-
10.0(Input and Current)	-	2500	-
11.0(Heating)	-	3000	-
13.0(Leakage Current and electric strength at operating temperature)	-	4000	-
14.0(Transient Overvoltage)	-	2000	-
15.0(Moisture resistance)	-	4000	-
16.0(Leakage current and Electric strength (After Humidity (Environmental) Treatment))	-	4000	-
19.0(Abnormal Operation)	-	2000	50% for Additional Core
21.0(Mechanical Strength)	-	2000	-
25.0(Supply Connection and External Flexible Cords)	-	2000	-
26.0(Terminals for external conductors)	-	2000	-
27.0(Provision For Earthing)	-	2000	-
28.0(Screws and Connections)	-	2000	-
30.0(Resistance To Heat and Fire)	-	4000	-
31.0(Resistance To Rusting)	-	2500	-
29.0(Creepage Distances and Clearances)	-	2500	-
22.0(Construction)	-	2000	-
23.0(Internal Wiring)	-	2000	-
17.0(Overload Protection of transformer and associated circuit)	-	2000	-
20.0(Stability and mechanical hazards)	-	5000	-

31 Dec, 2026

-
Excl: Cl. 19.11.4.1 to Cl. 19.11.4.7 (EMI/EMC tests)

IS 996 (2009)

Single phase a.c. induction motors for general purpose (Third Revision)

12825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Type of enclosures)	-	10000	-
12.6(Vibration Severity)	-	2000	-
12.1.1(Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-	5000	-
12.5.1(Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-	3000	-
13.1(High voltage test)	-	4000	-
13.2(Moisture proofness)	-	4000	-
13.3(Leakage current test)	-	2000	-
12.7(Insulation resistance test)	-	4000	-
12.2(Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-	2000	-

31 Dec, 2026

-
-

IS 4250 (1980)

Specification for domestic electric food - Mixers (Liquidizers And Grinders) (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8( Protection Against Electric Shock, IS 302-1)	-	2500	-
9(Starting, IS 302-1)	-	2000	-
10(Power Input and Current, IS 302-1)	-	2500	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	4000	-
15(Moisture Resistance, IS 302-1)	-	4000	-
19(Abnormal Operation, IS 302-1)	-	2000	-
25(Supply Connection and External Flexible Cords, IS 302-1)	-	2000	-
27(Provision for Earthing, IS 302-1)	-	2000	-
20(Stability & Mechanical Hazards, IS 302-1)	-	5000	-
21(Mechanical Strength, IS 302-1)	-	2000	-
Cl.26(Terminals for external conductors)	-	2000	-

31 Dec, 2026

-
Excl: Cl.19.11.4.1 to Cl.19.11.4.7 (EMI/EMC Test)

IS 9537 : Part 2 (1981)

Specification for conduits for electrical installations: Part 2 rigid steel conduits

10320 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking, IS 9537-2)	-	520	-
7.2.1(Dimensions, (Minimum outside Diameter), IS 9537-2)	-	2515	Dimensions and Uniformity of thickness
7.4(Screw threads, IS 9537-2)	-	2030	Thread Characteristics
8.2(Construction, IS 9537-2)	-	520	-
9.2(Mechanical Properties (Bending test), Cl. 9.3 of IS 9537-1)	-	1790	-
9.3(Mechanical Properties (Compression Test), IS 9537-2)	-	1790	-
13(External Influences, IS 9537-2)	-	1155	-

31 Dec, 2026

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

3150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause -4, 4.1( CARBON)	-	3795	Chemical Composition
Cl 5.1(Workmanship)	-	520	Freedom from defects
Cl 6.1(Diameter)	-	559	Nominal Size
Cl 9.3(Press)	-	1358	Bend Test

31 Dec, 2026

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Upto 4mm

5850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.1.1(Sulphur)	-	3795	Chemical Composition
Cl 4.1(Workmanship)	-	520	Freedom from defects
Cl 5 & 6(Diameter)	-	559	Nominal Size
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	1444	Reverse bent test

31 Dec, 2026

-
-

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

4950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	520	-
7.1.2 Fig.2(Minimum outside diameter of conduit)	-	503	Dimension and Uniformity of thickness
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	520	-
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	1790	-
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	1790	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	10889	-
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	1790	-
10(Resistance to Heat -Ball presure test)	-	4193	-
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	1154	-
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1652	-
7.1.1(Maximum and minimum outside diameter of socket)	-	503	-
7.1.1 Table-2(Length of Socket end)	-	503	-
7.1.2(Maximum and minimum outside diameter of conduit)	-	503	-
7.2(Minimum inside diameter of conduit)	-	503	-
7.4(Unifomity of The wall Thickness)	-	503	-

31 Dec, 2026

-
-

IS 204 : Part 1 (1991)

Tower bolts - Specification: Part 1 ferrous metals (Fifth Revision)

3300 View breakup
Rs.3300/- (10% concession for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	300	-
5.2.1 Table 1(Particulars-Barrel Tower Bolts)	-	500	-
5.2.2 Table 2(Particulars-Sami Barrel Tower Bolts)	-	300	-
5.2.3 Table 3(Particulars-Riveted or Spot Welded Tower Bolts)	-	300	-
5.2.4 Table 4(Particulars-Skeleton Tower Bolts)	-	300	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt-A 3.Length of Barrel-B 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of mild steel sheet for barrel-F 8.Dia of bore of barrel or socket- G )	-	300	-
6.2- Table 2(Dimension of Sami Barrel Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Bolt Plate or Socket-F 8.Dia of bore of Bolt Plate or socket G )	-	300	-
6.3- Table 3(Dimension of Riveted or Spot Welded Tower Bolts- 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7. Length of Strap-E" 8.Thickness of Back Plate -F 9.Thickness of Socket or Upper Plate and Strap- F" 10.Dia of bore of Bolt Plate or socket- G 11. Length of Alternative Socket-H )	-	300	-
6.4- Table 4(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Staple -F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob-J)	-	300	-
6.1- Table 1(Dimension of Barrel tower bolts-Minimum No. of equally Spaced Screw holes in Barrel and Socket for wood screw no 6)	-	300	-
6.2- Table 2(Dimension of Sami Barrel Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-	300	-
6.3- Table 3(Dimension of Riveted or Spot Welded Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-	300	-
6.4- Table 4(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 6)	-	300	-

31 Dec, 2026

-
-

IS 366 (1991)

Electric iron - Specification (Fourth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.0(Protection against access to live parts (as per Cl. 8 of IS 302-2-3 and IS 302-1))	-	2500	-
9.0(Power input and current (as per Cl. 10 of IS 302-2-3 and IS 302-1))	-	2500	-
9.0(Temperature Rise (as per Cl. 11 of IS 302-2-3 and IS 302-1))	-	3000	-
9.0(Leakage current and Electric Strength at Operating Temperature (as per Cl. 13 of IS 302-2-3 and IS 302-1))	-	4000	-
9.0(Transient Overvoltage (as per of Cl. 14 of IS 302-2-3 and Table 6 of IS 302-1))	-	2000	-
9.0(Moisture Resistance (as per of Cl.15 of IS 302-2-3 and IS 302-1))	-	2000	-
7.0(Classification (as per Cl.6 of IS 302-2-3 and Cl.6.1 of IS 302-1))	-	2000	-
9.0(Abnormal Operation (as per of Cl.19 of IS 302-2-3 and IS 302-1) )	-	2000	-
9.0(Staibilty and mechanical hazards (as per of Cl.20 of IS 302-2-3 and IS 302-1) )	-	5000	-
9.0(Mechanical strength (as per of Cl.21 of IS 302-2-3 and IS 302-1) )	-	2000	-
9.0(Supply connection and external flexible cord (as per of Cl.25 of IS 302-2-3 and IS 302-1) )	-	2000	-
9.0(Terminals for external conductors (as per of Cl.26 of IS 302-2-3 and IS 302-1) )	-	2000	-
9.0(Provision for earthing (as per of Cl.27 of IS 302-2-3 and IS 302-1) )	-	2000	-
9.0(Screw and connections (as per of Cl.28 of IS 302-2-3 and IS 302-1))	-	2000	-
9.0(Resistance to Heat and Fire (as per of Cl.30 of IS 302-2-3 and IS 302-1))	-	4000	-
9.0(Resistance to Rusting (as per of Cl.31 of IS 302-2-3 and IS 302-1))	-	2500	-
9.0(Clearances, creepage distances and solid insulation (as per of Cl.29 of IS 302-2-3 and IS 302-1))	-	2500	-
10.0(Measurement of Heating up time)	-	5000	-
11.0(Measurement of sole plate temperature)	-	5000	-
12.0(Measurement of Tempearture Distribution)	-	5000	-
13.0(Measurement of Initial overswing temperature and Heating up excess temperature)	-	5000	-
14.0(Measurement of Cyclic fluctuation of temperature of hottest point )	-	5000	-
16.0(Measurement of Thermostatic staibility)	-	5000	-

31 Dec, 2026

-
Excl: Cl.19.11.4.1 to Cl.19.11.4.7 (EMI/EMC Test)

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

4800 View breakup
Rs.4800/- (10% concession for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-	4500	-
5.1(General)	-	300	-
5.2.1 Table 1(Particulars-Barrel Tower Bolts)	-	300	-
5.2.2 Table 2(Particulars-Skeleton Tower Bolts)	-	300	-
6.1- Table 1(Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-	300	-
6.2- Table 2(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-	300	-
6.2- Table 2(Dimension of Skeleton Tower Bolts- Nos of Staples)	-	300	-
6.2- Table 2(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-	300	-
6.2- Table 3(PACKING)	-	300	-

31 Dec, 2026

-
-

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

4500 View breakup
Rs.4500/- (10% concession for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	2400	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	600	-
6.1(Manufacture- General)	-	300	-
6.2- Table 2,3,4,5 (Kunckles)	-	300	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	300	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	300	-
6.3.3 Fig-1(Position of Holes)	-	300	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	300	-

31 Dec, 2026

-
-

IS 285 (1992)

Laundry soaps - Specification (Third Revision)

13650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4, Table-1 (ix) Type-2 (Built soap) Gr-2(LSD/NSD content, IS 4955)	-	1050	-
5.4, Table-1 (viii) Type-2 (Built soap) Gr-1 & Gr-2(Chloride (as sodium chloride), IS 286)	-	950	-
5.4, Table-1 (viii) Type-1 (Pure soap)(Chloride (as sodium chloride), IS 286)	-	950	-
5.4, Table-1 (vii) Type-1 (Pure soap)(Glycerol, IS 286)	-	1050	-
5.4, Table-1 (vi) Type-1 (Pure soap)(Titre of total fatty acids, IS 286)	-	1350	-
5.4, Table-1 (v) Type-2 (Built soap) Gr-1(Matter insoluble in alcohol, IS 286)	-	1050	-
5.4, Table-1 (iv) (Free caustic alkali, as sodium hydroxide (NaOH), IS 286)	-	950	-
5.4, Table-1 (iii) (Unsaponified fatty matter, IS 286)	-	1050	-
5.4, Table-1 (ii) (Rosin acids, percent by mass of total fatty matter, IS 286 )	-	1050	-
5.4, Table-1 (i) Type-2 (Built soap) Gr-2(Total fatty matter, IS 286)	-	1350	-
5.3(Odour and Lathering Properties, IS 286)	-	500	-
5.1.1(Phenolic substances, IS 286)	-	950	-

31 Dec, 2026

-
-

IS 1746 (1992)

Shoe polish, paste - Specification (Third Revision)

13050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Odour)	-	850	-
4.1.2(Colour)	-	850	-
4.1.3(Consistency)	-	850	-
4.1.4(Applicability)	-	850	-
4.1.6(colour of water extract)	-	850	-
4.2 (table 1 S.no(i))(Softeing point of non-volatile matter)	-	850	-
4.2 (table 1 S.no(ii))(Ash of the non-volatile matter)	-	850	-
4.2 (table 1 S.no(iii))(pH of water extract )	-	850	-
4.2 (table 1 S.no(iv))(Distillation range of volatile portion )	-	850	-
4.2 (table 1 S.no(v))(Flash point of volatile portion,)	-	850	-
4.2 (table 1 S.no(vi))(Non-volatile matter )	-	850	-

31 Dec, 2026

-
-

IS 2074 (2015)

Ready mixed paint, air drying, red oxide - Zinc chrome, priming - Specification (Third Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1 (a)(Composition, Pigment, Cl 5.1.1)	-	500	-
Cl 5.1 (b)(Composition, Driers)	-	500	-
Cl 5.1 .1 (a)(Zinc chrome, (Type 2 of IS 51), Annex B)	-	500	-
Cl 5.1 .1 (b)(Synthetic red oxides of iron (conforming to Grade 2 or IS 44), (conforming to Grade 3 of IS 44), 6 of IS 6947 (Part 2))	-	500	-
Cl 5.1 .1 (c)(Suitable extenders)	-	500	-
Cl 5.1.2(Volatile vehicle)	-	500	-
Cl 5.2(Material)	-	500	-
Cl 5.3(Compatibility with Thinner, IS 1872)	-	500	-
Cl 5.4(Freedom from Objectionable Impurities)	-	500	-
Cl 5.5(Lead Restriction, IS 101(Part 8/Sec 5))	-	1000	-
1 (i) (a) Table 1(Consistency, Annex C)	-	500	-
1 (i) (b) Table 1(Viscosity by ford cup No. 4, IS 101 (Part1/sec5))	-	500	-
1 (ii) Table 1(Mass, IS 101 (Part1/sec7))	-	500	-
1 (iii) (a) Table 1(Drying time, Surface Dry, IS 101 (Part3/sec1))	-	500	-
1 (iii) (b) Table 1(Drying time, Hard Dry, IS 101 (Part3/sec1))	-	500	-
1 (iv) (a) Table 1(Finish, IS 101 (Part3/sec4))	-	500	-
1 (iv) (b) Table 1(Gloss, IS 101 (Part4/sec4))	-	500	-
1 (v) Table 1(Fineness of grind, IS 101 (Part 3/Sec 5))	-	500	-
1 (vi) Table 1(Colour, IS 101 (Part 4/Sec 2))	-	500	-
1 (vii) (a) Table 1(Flexibility and adhesion: Bend test (with 6.25 mm dia mandrel and in type 1 apparatus), Clause 2 of IS 101 (Part 5/Sec 2))	-	800	-
1 (vii) (b) Table 1(Scratch hardness (load 1 000g), Clause 3 of IS 101 (Part 5/Sec 2))	-	500	-
1 (viii) Table 1(Flash point, IS 101 (Part l/Sec 6))	-	500	-
1 (ix) Table 1(Volume solids, IS 101 (Part 8/Sec 6))	-	800	-
1 (x) (a) Table 1(Resistance to humidity under condition of condensation: Resistance to humidity, Clause 2 of IS 101 (Part 6/Sec 1))	-	2000	-
1 (x) (b) Table 1(Resistance to humidity under condition of condensation: Resistance to sea water (applicable for marine paints only), Annex D)	-	2000	-
1 (x) (c) Table 1(Resistance to humidity under condition of condensation: Resistance to salt spray, Annex E)	-	2000	-
1 (xi) Table 1(Accelerated storage stability test, Annex F)	-	2000	-

31 Dec, 2026

-
-

Bureau of Indian Standards

The National Standards Body of India

MSME Testing Centre, New Delhi

Shaheed Capt. Gaur Marg, Okhla Phase -III, New Delhi, South East, Delhi, 110020

9910201527 dctc-nr@dcmsme.gov.in

Scope List