BIS - LIMS (Laboratory Information Management System)

NATIONAL TEST HOUSE-ER (NTH), KOLKATA

BLOCK-CP, SECTOR-V,, SALT LAKE CITY, Kolkata, 24 PARAGANAS NORTH, West Bengal, 700091

9968653673 director-kol@nth.gov.in

Scope List

Reset

67 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

All Grade as per Specification

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5 & 6(Diameter)	-	1000	-
Clause 7.1(Ultimate Tensile Stress)	-	1000	-
Clause 7.1(Proof Stress (0.2 percent ))	-	1000	-
Cl. 7.1(Elongation)	-	1000	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	1000	-
Cl 4.1(Workmanship)	-	1000	-
Clause 3.1.1(Sulphur)	-	1000	-
Clause 3.1.1(Phosphorus)	-	1000	-

14 Jun, 2027

-
-

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

All Grade as per Specification

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimension - IS 3965)	-	1000	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	2000	-
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	2000	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	1000	-
Cl. 4(Freedom from Defects)	-	1000	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	1000	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	500	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	1000	-

14 Jun, 2027

-
-

IS 733 (2025)

Wrought Aluminium and Aluminium Alloy Bars, Rods, Sections, Extruded Tube, Hollow Sections and Profiles for General Engineering Purposes ? Specification (Fourth Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 Table 1 - Table 8(Zirconium +Titanium)	-	500	-
Cl-6.1, Table-1 to 8(Fe)	-	500	-
Cl-6.1, Table-1 to 8(Cu)	-	500	-
Cl-6.1, Table-1 to 8(Mn)	-	500	-
Cl-6.1, Table-1 to 8(Mg)	-	500	-
Cl-6.1, Table-1 to 8(Cr)	-	500	-
Cl-6.1, Table-1 to 8(Zn)	-	500	-
Cl-6.1, Table-1 to 8(Ti)	-	500	-
Cl-6.1, Table-1 to 8(V)	-	500	-
Cl-7.1, 7.2 & 7.3, Table-9(Dimensions)	-	1000	-
Cl-7.1, 7.2 & 7.3, Table-9(Rm MPa)	-	2000	-
Cl-7.1, 7.2 & 7.3, Table-9(Rp0.2 MPa)	-	2000	-
Cl-7.1, 7.2 & 7.3, Table-9(Elongation , Percent)	-	1000	-
Cl-9(Dimensions and Tolerances)	-	0	-
Cl-12(Packaging and Marking)	-	0	-
Cl-7.1(Tensile test)	-	0	-
Cl-5(Freedom from Defects)	-	1000	-
Cl-6.1, Table-1 to 8(Si)	-	500	-
Cl-4(General requirements)	-	0	-
Cl-6.1, Table-1 to 8(Aluminium)	-	500	-
Cl-6.2(chemical analysis)	-	0	-

14 Jun, 2027

-
-

IS 738 (1994)

Wrought aluminium alloys, drawn tube for general engineering purposes - Specification (Third Revision)

All Grade

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7, IS 2678(Wall Thickness at any point)	-	500	-
Cl.7, IS 2678(Mean Wall Thickness)	-	500	-
Cl. 9.1 Table 2(Tensile Strength- IS 2657)	-	2000	-
Cl. 9.1 Table 2(0.2 percent proof stress- IS 2657)	-	2000	-
Cl. 9.1 Table 2(Elongation on guage length of 50 mm)	-	1000	-
Cl. 6(Freedom from Defects- Cl.6)	-	1000	-
Cl. 8.1, Table 1(Aluminium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Copper- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Magnesium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Silicon- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Iron- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Manganese- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Zinc- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Titanium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-
Cl. 8.1, Table 1(Chromium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	500	-

14 Jun, 2027

-
-

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	500	-
Cl-8.1(Dimensions -length)	-	1000	-
Cl-8.2(Thickness of the plywood boards)	-	500	-
Cl-8.3(Squareness)	-	1000	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	2000	-
Cl-11.3.2(Mycological Test)	-	1500	-
Cl-11.4(Moisture Content)	-	1000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	2000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	2000	-
Cl-5.1(Classification by appearance)	-	500	-
Cl-5.2, Table- 1 (i)(Blister)	-	250	-
Cl-5.2, Table- 1 (ii)(Checks)	-	250	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	250	-
Cl-5.2, Table- 1 (iv)(Dote)	-	250	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	250	-
Cl-5.2, Table- 1 (vi)(Joints)	-	250	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	250	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	250	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	250	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	250	-
Cl-5.2, Table- 1 (xi)(Patches)	-	250	-
Cl-5.2, Table- 1 (xii)(Splits)	-	250	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	250	-
Cl-7.2.1(Thickness of veneers)	-	500	-
Cl-7.2.3(Grain Direction)	-	500	-

14 Jun, 2027

-
-

IS 13801 (2013)

Chequered Cement Concrete Tiles -

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	500	-
Cl 12.1(Concavity & Convexity )	-	500	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	500	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	500	-
Cl 12.4(Water absorption)	-	1000	-
Cl 12.5(Wet transverse strength)	-	2000	-
Cl 12.6(Resistance to wear)	-	2500	-

14 Jun, 2027

-
-

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

All Grade

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 13(Length, Width & Thickness)	-	1000	-
8, Table 5 & 6(Tensile Strength)	-	1000	-
8, Table 5 & 6(Yield Strength)	-	1000	-
8, Table 5 & 6(Elongation)	-	1000	-
9(Bend test)	-	1000	-
Clause 10(Cuppping Test)	-	2000	-
Cl 12(Workmanship)	-	1000	-
6.1(Carbon %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Silicon %)	-	500	-
6.1(V)	-	500	-
6.1( Ti)	-	500	-
6.1( Nb)	-	500	-
6.1( Nitrogen%)	-	500	-
6.1( Aluminium %)	-	500	-
6.1( Copper %)	-	500	-

14 Jun, 2027

-
-

IS 1856 (2005)

Steel wire ropes for haulage purposes - Specification (Third Revision)

All Grade as per Specification

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4- Tables 1 to 4(Diameter)	-	1000	-
5- Tables 1 to 4(Breakiing Force of Rope with Steel Core)	-	3000	-
6.3(Lay)	-	1000	-
6.4- Tables 1 to 4(Mass of Rope with Steel core)	-	1500	-
7(Uniformity of Znic coating - IS 1835 & IS 2366)	-	1000	-
7(Mass of Znic Coating - IS 1835 & IS 6745)	-	2000	-
5- Tables 1 to 4(Breakiing Force of Rope with Fiber Core)	-	3000	-
6.4- Tables 1 to 4(Mass of Rope with Fiber core)	-	1500	-

14 Jun, 2027

-
-

IS 10702 (1992)

Rubber hawal chappal - Specification (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4(Stud bolt)	-	1000	-
5.4(Stud diameter)	-	1000	-
5.4(Hardness (Shore A))	-	1000	-
5.4(Hardness (shore A)- after ageing)	-	1000	-
5.4(Tear strength )	-	1000	-
5.4(Breaking strength )	-	1000	-
5.4(Elongation at break )	-	1000	-
5.4(Tensile Strength )	-	1000	-
5.4(Relative density )	-	1000	-
5.4(Shrinkage test (at 100 C temp))	-	1000	-
5.4(Shrinkage test (at room temp))	-	1000	-
5.4(Split tear strength )	-	1000	-
5.4(Compression set)	-	1000	-
5.4(Hardness (Shore A))	-	1000	-
5.4(Relative density)	-	1000	-
5.3(Thickness )	-	1000	-
5.1(Shape & Design)	-	1000	-

14 Jun, 2027

-
-

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

All Grades

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.2(Width)	-	500	-
8.2(Thickness)	-	500	-
5.2(Tensile Strength, Mpa)	-	1000	-
5.2(Tensile Test-1608:Part 1)	-	1000	Yield Strength / 0.2 % Proof Stress
5.2(Elongation, %)	-	1000	-
5.3(Bend Test-1599)	-	1000	-
Cl.4(Sulphur -IS 228 or method specified in relevant ISO standard)	-	500	-
Cl.4(Phosphorus -IS 228 or method specified in relevant ISO standard)	-	500	-

14 Jun, 2027

-
-

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

PPC (Fly Ash Based)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	0	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	250	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	250	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1000	-
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	2000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-

14 Jun, 2027

-
-

IS 455 (2015)

Portland slag cement - Specification

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table 1 i(Fineness IS 4031(Part 2))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 ii a (Soundness , Le Chatelier Expansion ))	-	500	-
7 Table 1 ii b(Soundness, Autoclave expansion IS 4031(Part 3) )	-	1000	-
7 Table 1 iii a(Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-	250	-
7 Table 1 iii b(Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-	250	-
7 Table 1 iv a(Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-	1000	-
7 Table 1 iv b(Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 ii b (Expansion after aeration ))	-	0	-
7 Table 1 iv c(Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-	1000	-
7 Table 1 v(Transverse strength (optional) IS 4031(Part 8) )	-	2000	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	1000	-

14 Jun, 2027

-
-

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table-3 i.(Fineness)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	500	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 ii b(Expansion after aeration)	-	0	-
7 Table-3 iii a(Setting Time Initial)	-	250	-
7 Table-3 iii b(Setting Time Final)	-	250	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
6.1 Table-2 viii(Alkali content)	-	500	-
6.1 Table-2 vii(Chloride content)	-	500	-
6.1 Table-2 vi(Loss on ignition)	-	500	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	500	-
6.1 Table-2 iv(Magnesia)	-	500	-
6.1 Table-2 iii.(Insoluble residue)	-	500	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	500	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	500	-

14 Jun, 2027

-
-

IS 15477 (2019)

Adhesives for use with ceramic tiles and mosaics

Type-1, 2, 3, 4, 5

23000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	1000	-
5.1(Tensile Adhesion Strength )	-	2500	Tensile Adhesion Strength- Dry Condition
5.1(Tensile Adhesion Strength)	-	2500	Tensile Adhesion Strength- Wet Condition
5.2(Shear Adhesion Strength )	-	3000	Shear Adhesion Strength- Dry Condition
5.2(Shear Adhesion Strength)	-	3000	Shear Adhesion Strength- Wet Condition
5.2(Shear Adhesion Strength)	-	3000	Shear Adhesion Strength- Heat Ageing Condition
5.3(OpenTime)	-	1000	Open time
5.4(Adjustment Time)	-	1000	Adjustment Time
5.5(Slip (Required for Vertical Application Only))	-	3000	Slip
5.6(Deformability (Required for VerticalApplication Only))	-	3000	Deformability

14 Jun, 2027

-
-

IS 3319 (1995)

Blades, surgical, detachable (Bard Parker Type) and handles - Specification (Fourth Revision)

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.1 & 5.2; Table 1(Shape and dimensions)	-	1000	-
6,6.1(Workmanship and Finish)	-	1000	-
6,6.2(Workmanship and Finish)	-	0	-
6,6.3(Workmanship and Finish)	-	0	-
6,6.4(Workmanship and Finish)	-	0	-
7.1(Hardness test)	-	2000	-
9.1( Visual Examination)	-	1000	-
9.2( Performance Test)	-	2000	-
10.1.1( Marking on Blade)	-	100	-
10.1.2(Packages of Non-sterile Blades)	-	100	-
10.1.3,10.1.3.1(Packages of sterile Blades,Unit containers for sterile Blades)	-	100	-
10.1.3,10.1.3.2(Packages of sterile Blades , Outer containers for sterile blade)	-	0	-
10.2( Handles)	-	0	-
10.2.2( Packages of Handles)	-	100	-
11,11.1,11.1.1( Packages of Non-sterile Blades ; Unit container)	-	0	-
11,11.1,11.1.2( Packages of Non-sterile Blades ; Outer container)	-	0	-
11.2,11.2.1(Packages of Sterile Blades)	-	0	-
11.2,11.2.2( Packages of Sterile Blades ; Unit container)	-	0	-
11.2,11.2.3( Packages of sterile Blades ; Outer container)	-	0	-
11.4(Packaging of Handles)	-	0	-
Clause -4, 4.1(TITANIUM)	-	500	-
Clause -4, 4.1(VANADIUM)	-	500	-
Clause -4, 4.1(Molybdenum)	-	500	-
Clause -4, 4.1(Chromium)	-	500	-
Clause -4, 4.1(Nickel)	-	500	-
Clause -4, 4.1( ALUMINIUM)	-	500	-
Clause -4, 4.1(SILICON)	-	500	-
Clause -4, 4.1(MANGANESE)	-	500	-
Clause -4, 4.1(PHOSPHURS)	-	500	-
Clause -4, 4.1(SULPHUR)	-	500	-
Clause -4, 4.1( CARBON)	-	500	-

14 Jun, 2027

-
-

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	1200	-
6(Interchangeability)	-	1200	-
7(Protection against accidental contact with live parts)	-	1200	-
8(Insulation Resistance and Electric Strength)	-	5000	-
9(MECHANICAL STRENGTH)	-	1200	-
10(cap temperature)	-	2000	-
11(Resistance to Heat)	-	2000	-
12(Resistance to Flame and Ignition)	-	5000	-
13(Fault conditions)	-	2000	-
14(Creepage distance and clearances)	-	1200	-
4(General requirement and General test requirements)	-	0	-
8(Strength after humidity treatment)	-	5000	-
5(Marking)	-	1200	-
6(Interchangeability)	-	1200	-
7(Protection against accidental contact with live parts)	-	1200	-
9(Mechanical strength)	-	1200	-
10(Cap temperature rise)	-	2000	-
11(Resistance to heat)	-	2000	-
12(Resistance to flame and ignition)	-	5000	-
13(Fault conditions)	-	2000	-
14(Creepage distances and clearances)	-	1200	-
15(Selection of lamps for tests (Sampling))	-	0	-
16(Condition of compliance)	-	0	-
17(Tests)	-	0	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	0	-
Annex B(Lamps with operating position limitations)	-	0	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	0	-

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	0	-
6.0(Marking)	-	1200	-
7.0(Construction)	-	1200	-
8.0(Creepage Distance and Clearances)	-	1200	-
9.0(Provision for earthing)	-	1200	-
10.0(Terminals)	-	1200	-
11.0(External & Internal Wiring)	-	1200	-
12.0(Protection against electric shock)	-	1200	-
13.0(Endurance Tests and Thermal Tests)	-	5500	-
14.0(Resistance to Dust & Moisture)	-	12000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	12000	-
17.0(Photometric Test)	-	10000	-
(Cl.4.24) (Annex-P)(UV Radiations for metal halide lamps)	-	0	-
4.26.2(Short Circuit Protection)	-	0	-

14 Jun, 2027

-
-

IS 16103 : Part 1 (2012)

Led modules for general lighting: Part 1 safety requirements

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	500	NA
8(Terminals)	-	500	NA
9(PROVISION FOR EARTHING)	-	1000	NA
10(Protection against accidental contact with live parts)	-	500	NA
11(Mositure Resistance and Insulation)	-	3500	NA
12(Electric Strength)	-	1500	NA
13(Fault conditions)	-	1500	NA
15(Construction)	-	500	NA
16(Creepage distance and clearances)	-	500	NA
17(Screws, current carrying parts and connections)	-	1000	NA
18(Resistance to heat, fire and tracking)	-	12000	NA
19(Resistance to corrosion)	-	2000	NA

14 Jun, 2027

-
-

IS 16103 : Part 2 (2012)

Led modules for general lighting: Part 2 performance requirements

60000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Dimensions)	-	500	NA
7(Module Power)	-	2000	NA
8(Light Output)	-	5000	NA
9(Chromaticity Coordinates, Correlated colour temperature and colour rendering)	-	5000	NA
10(LED Module Life)	-	45000	NA
12(Information for Luminaire design)	-	500	NA

14 Jun, 2027

-
-

IS 16104 (2012)

D.C. or A.C. supplied electronic control gear for led modules - Performance requirements

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Classification)	-	500	NA
6(Marking)	-	500	NA
7.2(Output voltage and Current)	-	1000	NA
7.3(Capacitive Load Requirement)	-	500	NA
7.4(Voltage surge during switching and operation)	-	1500	NA
8(Total Circuit Power)	-	2000	NA
9(Circuit Power Factor)	-	1000	NA
10(Supply Current)	-	1000	NA
12(Operational test for abnormal conditions)	-	2000	NA
13(Endurance)	-	20000	NA

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 4 (1987)

Specification for luminaires: Part 5 particular requirements: Sec 4 portable general purpose luminaires

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	500	Individual test charge 1200/- per sample for this tests.
6(Construction)	-	1000	Individual test charge 1200/- per sample for this tests.
7(Creepage Distance And Clearances)	-	1000	Individual test charge 1200/- per sample for this tests.
8(Provision for Earthing)	-	1000	Individual test charge 1200/- per sample for this tests.
9(Terminals)	-	1000	Individual test charge 1200/- per sample for this tests.
10(External & Internal Wiring)	-	500	Individual test charge 1200/- per sample for this tests.
11(Protection Against Electric Shock )	-	1000	Individual test charge 1200/- per sample for this tests.
13.3(Mechanical Strength Test )	-	1000	Individual test charge 1200/- per sample for this tests.
13.4(Endurance Test and Thermal test)	-	5000	Individual test charge 5500/- per sample for this tests.
13.5(Resistance To Dust & Moisture)	-	7500	Individual test charge 12000/- per sample for this tests.
13.6(Insulation Resistance and Electric Strength)	-	3000	Individual test charge 5000/- per sample for this tests.
13.7(Resistance to Heat, Fire & Tracking)	-	7500	Individual test charge 12000/- per sample for this tests.
13.8(Photometric Test)	-	10000	NA

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 7 (2017)

Luminaires: Part 5 particular requirements: Sec 7 lighting chains (First Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
20.4(General Test Requireements)	-	500	Individual test charge 1200/- per sample for this tests.
20.5(Classification of Luminaires')	-	500	Individual test charge 1200/- per sample for this tests.
20.6(Marking)	-	500	Individual test charge 1200/- per sample for this tests.
20.7(Construction)	-	1000	Individual test charge 1200/- per sample for this tests.
20.8(Creepage Distance and Clearances)	-	1000	Individual test charge 1200/- per sample for this tests.
20.9(Provision for earthing)	-	1000	Individual test charge 1200/- per sample for this tests.
20.10(Terminals)	-	1000	Individual test charge 1200/- per sample for this tests.
20.11(External & Internal Wiring)	-	500	Individual test charge 1200/- per sample for this tests.
20.12(Protection against electric shock)	-	1000	Individual test charge 1200/- per sample for this tests.
20.13(Endurance Tests and Thermal Tests)	-	5000	Individual test charge 5500/- per sample for this tests.
20.14(Resistance to Dust & Moisture)	-	7500	Individual test charge 12000/- per sample for this tests.
20.15(Insulation Resistance and Electric Strength)	-	3000	Individual test charge 5000/- per sample for this tests.
20.16(Resistance to Heat , fire and tracking)	-	7500	Individual test charge 12000/- per sample for this tests.

14 Jun, 2027

-
-

IS 10322 : PART 5 : SEC 3 (2012)

Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	0	-
6.0(Marking)	-	1200	-
7.0(Construction)	-	1200	-
8.0(Creepage Distance and Clearances)	-	1200	-
9.0(Provision for earthing)	-	1200	-
10.0(Terminals)	-	1200	-
11.0(External & Internal Wiring)	-	1200	-
12.0(Protection against electric shock)	-	1200	-
13.0(Endurance Tests and Thermal Tests)	-	5500	-
14.0(Resistance to Dust & Moisture)	-	12000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	12000	-
17.0(Photometric Test)	-	10000	-

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 5 (2013)

Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	0	-
6.0(Marking)	-	1200	-
7.0(Construction)	-	1200	-
8.0(Creepage Distance and Clearances)	-	1200	-
9.0(Provision for earthing)	-	1200	-
10.0(Terminals)	-	1200	-
11.0(External & Internal Wiring)	-	1200	-
12.0(Protection against electric shock)	-	1200	-
13.0(Endurance Tests and Thermal Tests)	-	5500	-
14.0(Resistance to Dust & Moisture)	-	12000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	12000	-
17.0(Photometric Test)	-	10000	-

14 Jun, 2027

-
-

IS 10322 : Part 5 : Sec 6 (2013)

Luminaires: Part 5 particular requirements: Sec 6 handlamps

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.2(Packing -Each Package shall bear the following Particulars)	-	0	-
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	0	-
6.0(Marking)	-	1200	-
7.0(Construction)	-	1200	-
8.0(Creepage Distance and Clearances)	-	1200	-
9.0(Provision for earthing)	-	1200	-
10.0(Terminals)	-	1200	-
11.0(External & Internal Wiring)	-	1200	-
12.0(Protection against electric shock)	-	1200	-
13.0(Endurance Tests and Thermal Tests)	-	5500	-
14.0(Resistance to Dust & Moisture)	-	12000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	12000	-

14 Jun, 2027

-
-

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimensions)	-	1000	-
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	3000	-
8.2(Mechanical Properties (as per IS 1717))	-	1000	-
8.3(Mechanical Properties (as per IS 1755))	-	1000	-
9.1(Galvanizing Requirements )	-	2000	-
9.2(Galvanizing Requirements )	-	1000	-
9.3(Galvanizing Requirements )	-	1000	-
11(Freedom from defects)	-	1000	-
6.2(Sulphur %)	-	500	-
6.2(Phosphorus %)	-	500	-
8.4(Mechanical Properties (as per IS 10810(Part- 42)))	-	3000	-

14 Jun, 2027

-
-

IS 10702 (2023)

Hawai Chappal-Specification

31000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	2000	-
4.2(Length)	-	500	-
4.3(Thickness)	-	500	-
4.4 , Table No. 1 , i)(Density)	-	1000	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	2000	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	1000	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	1000	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2000	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	1000	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	2000	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	500	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	500	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	2000	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	1000	-
Cl.No. 5.2(lead content)	-	500	-
Cl-4.4, Table -2 S. No-1 (iii), (Amendment No-1)(Lead content (as Pb), in ppm, Max)	-	500	-
Cl.4.4 - Table No 1 - Sl. No.-viii("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	500	-
Clause 4.1 - 4.1.1(Bottom Material)	-	500	-
Clause 4.1 - 4.1.2(Strap Material)	-	2000	-
Clause 4.1 - 4.1.3(Material)	-	500	-
Clause 4.1 - 4.1.4(Material)	-	500	-
Clause 4.2(Material)	-	500	-
Clause 4.3 - 4.3.1(Thickness)	-	500	-
Clause 4.3 - 4.3.2(Thickness)	-	500	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	1000	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	2000	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	1000	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	1000	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	1000	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	1000	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	1000	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	1000	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	1000	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	1000	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	500	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	500	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	500	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	500	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	1000	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	2000	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	1000	-
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	1000	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	1000	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	2000	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	2000	-
Cl-4.4, Table -1 S. No-1 (viii) (Amendment No-1)("Lead content (as Pb), ppm, Max")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	500	-
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	1000	-
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	1000	-
6(MARKING AND PACKING)	-	500	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	2000	-
Cl.4.4 - Table No 1 - Sl. No.-vii(pH- IS 1390:2022)	-	1000	-

14 Jun, 2027

-
-

IS 12894 (2002)

Pulverized fuel ash - Lime bricks - Specification

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Dimensions)	-	500	-
7.1, Table -1(Average Wet Compressive Strength)	-	2000	-
7.4(Water Absorption)	-	1000	-
7.3(Efflorescence Test)	-	1000	-
3.1(General Requirements)	-	500	-

14 Jun, 2027

-
-

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	500	-
Cl 12.2(Concavity & Convexity )	-	500	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	500	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	500	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	2000	-
Cl 12.7(Resistance to wear)	-	2500	-

14 Jun, 2027

-
-

IS 15647 (2006)

Hot rolled steel narrow width strip for welded tubes and pipes

9165 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Tensile Strength-IS:1608(P1))	-	2000	-
8(Yield Strength-IS:1608(P1))	-	500	-
Cl. 8.2 Table 3(Elongation)	-	500	-
Cl 9(Press)	-	1000	-
Cl 11(Workmanship)	-	1000	-
Cl 12(Length, Width & Thickness)	-	1000	-
7(Carbon as C - IS:228)	-	500	-
7(Sulphur as S- IS:228)	-	500	-
7(Phosphorus as P-IS:228)	-	500	-
7(Manganese as Mn-IS:228)	-	500	-

14 Jun, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

NATIONAL TEST HOUSE-ER (NTH), KOLKATA

BLOCK-CP, SECTOR-V,, SALT LAKE CITY, Kolkata, 24 PARAGANAS NORTH, West Bengal, 700091

9968653673 director-kol@nth.gov.in

Scope List