BIS - LIMS (Laboratory Information Management System)

NATIONAL TEST HOUSE-ER (NTH), KOLKATA

BLOCK-CP, SECTOR-V,, SALT LAKE CITY, Kolkata, 24 PARAGANAS NORTH, West Bengal, 700091

9968653673 nthsal-wb@nic.in

Scope List

Reset

67 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 16106 (2012)

Method of electrical and photometric measurements of solid state lighting (Led) products

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Power supply characteristics)	-	500	NA
6(Seasoning (Ageing) of SSL products)	-	500	NA
7(Stabilization of SSL products)	-	500	NA
8(Operating orientation)	-	500	NA
9(Electrical settings)	-	500	NA
10(Electrical instrumentation)	-	500	NA
11(Test methods for total luminous flux measurement)	-	2000	NA
12(Luminous intensity distribution)	-	5000	NA
13(Luminous efficacy)	-	1000	NA
14(Test methods for colour characteristics of SSL products)	-	5000	NA
15(Uncertainty statement)	-	1000	NA
16(Test report)	-	1000	NA

14 Jun, 2027

-
-

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	1000	-
5/5.1(REQUIREMENTS-General)	-	1000	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	1000	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	1000	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	1000	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	6000	-

14 Jun, 2027

-
Included w.e.f. 15.03.2024

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Flexing resistance )	-	1000	-
4.2(Water absorption)	-	1000	-
4.2(Heat Shrinkage )	-	1000	-
4.2(Shrinkage at room temp)	-	1000	-
4.2(Split tear strength)	-	1000	-
4.2(Compression set)	-	1000	-
4.2(Hardness (Shore A))	-	1000	-
4.2(Density )	-	1000	-
4.2(Size & Thickness )	-	1000	-

14 Jun, 2027

-
Included w.e.f. 15.03.2024

IS 10702 (1992)

Rubber hawal chappal - Specification (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4(Stud bolt)	-	1000	-
5.4(Stud diameter)	-	1000	-
5.4(Hardness (Shore A))	-	1000	-
5.4(Hardness (shore A)- after ageing)	-	1000	-
5.4(Tear strength )	-	1000	-
5.4(Breaking strength )	-	1000	-
5.4(Elongation at break )	-	1000	-
5.4(Tensile Strength )	-	1000	-
5.4(Relative density )	-	1000	-
5.4(Shrinkage test (at 100 C temp))	-	1000	-
5.4(Shrinkage test (at room temp))	-	1000	-
5.4(Split tear strength )	-	1000	-
5.4(Compression set)	-	1000	-
5.4(Hardness (Shore A))	-	1000	-
5.4(Relative density)	-	1000	-
5.3(Thickness )	-	1000	-
5.1(Shape & Design)	-	1000	-

14 Jun, 2027

-
-

IS 6719 (1972)

Solid Pvc Soles And Heels

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6.1(Hardness )	-	1000	-
3.6 (i)(Relative density )	-	1000	-
3.6 (ii)(Tensile Strength )	-	1000	-
3.6 (iii)(Elongation at break, percent )	-	1000	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	1000	-
3.6 (v)(Volatility, percent by means )	-	1000	-
3.6 (vi)(Lead (as Pb) ppm)	-	2000	-

14 Jun, 2027

-
Included w.e.f. 05.01.2024

IS 6721 (1972)

Specification for PVC sandal

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Hardness (IRHD))	-	1000	-
4.0(Tensile Strength )	-	1000	-
4.0(Density )	-	1000	-
4.0(Elongation at break )	-	1000	-
4.0(Tear strength )	-	1000	-
4.0(Volatility % by mass)	-	2000	-
4.0(Lead Content )	-	2000	-
4.4(Dimension)	-	1000	-

14 Jun, 2027

-
-

IS 3735 (1996)

Canvas Shoes, Rubber Sole

21750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 (Drill) (End & Picks/dm)	-	1000	-
4.1.1 (Drill) (Colorfastness to light )	-	3000	-
4.1.1 (canvas )(End & Picks/dm)	-	1000	-
4.1.1 (canvas )(Breaking Load )	-	2000	-
4.1.1.1(Colorfastness to light )	-	3000	-
4.1.1.2(Colorfastness to washing)	-	2000	-
4.1.2(Width )	-	1000	-
4.1.2(Breaking Strength )	-	2000	-
4.1.2(Colorfastness to washing)	-	2000	-
4.1.2(Colorfastness to light )	-	3000	-
4.1.3(Construction )	-	1000	-
4.1.3(Single thread breaking load)	-	2000	-
4.1.3(Colorfastness to light )	-	3000	-
4.1.3(Colorfastness to washing)	-	2000	-
4.1.3(Color fastness to perspiration)	-	2000	-
4.1.4(Size )	-	1000	-
4.1.4(Thickness)	-	1000	-
4.1.5(Length )	-	1000	-
4.1.5(Sulpher dyes content )	-	1000	-
4.1.6(Relative density)	-	1000	-
4.1.6(Hardness )	-	1000	-
4.1.6(Flexing resistance test)	-	2000	-
4.1.6(Hardness (after accelerated ))	-	1000	-
4.1.6(Tensile strength)	-	2000	-
4.1.6(Elongation at break )	-	1000	-
4.1.6(Compression set )	-	2000	-
4.1.6.2(Tensile after ageing )	-	3000	-
4.1.6.2(Elongation at break after ageing )	-	2000	-
4.1.6.2(Ageing)	-	2000	-
4.1.6.2(Thickness of components )	-	1000	-
4.2(Design )	-	1000	-
4.3(Leg Height )	-	1000	-
4.4(Contruction )	-	1000	-
4.6(Mass )	-	1000	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	1000	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	1000	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	1000	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	1000	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	1000	-
4.1.1 (Drill) (End & Picks/dm)	-	0	Repeated
4.1.1 (Drill) (Colorfastness to light )	-	0	Repeated
4.1.1 (canvas )(End & Picks/dm)	-	0	Repeated
4.1.1 (canvas )(Breaking Load )	-	0	Repeated
4.1.1.1(Colorfastness to light )	-	0	Repeated
4.1.1.2(Colorfastness to washing)	-	0	Repeated
4.1.2(Width )	-	0	Repeated
4.1.2(Breaking Strength )	-	0	Repeated
4.1.2(Colorfastness to washing)	-	0	Repeated
4.1.2(Colorfastness to light )	-	0	Repeated
4.1.3(Construction )	-	0	Repeated
4.1.3(Single thread breaking load)	-	0	Repeated
4.1.3(Colorfastness to light )	-	0	Repeated
4.1.3(Colorfastness to washing)	-	0	Repeated
4.1.3(Color fastness to perspiration)	-	0	Repeated
4.1.4(Size )	-	0	Repeated
4.1.4(Thickness)	-	0	Repeated
4.1.5(Length )	-	0	Repeated
4.1.5(Sulpher dyes content )	-	0	Repeated
4.1.6(Relative density)	-	0	Repeated
4.1.6(Hardness )	-	0	Repeated
4.1.6(Flexing resistance test)	-	0	Repeated
4.1.6(Hardness (after accelerated ))	-	0	Repeated
4.1.6(Tensile strength)	-	0	Repeated
4.1.6(Elongation at break )	-	0	Repeated
4.1.6(Compression set )	-	0	Repeated
4.1.6.2(Tensile after ageing )	-	0	Repeated
4.1.6.2(Elongation at break after ageing )	-	0	Repeated
4.1.6.2(Ageing)	-	0	Repeated
4.1.6.2(Thickness of components )	-	0	Repeated
4.2(Design )	-	0	Repeated
4.3(Leg Height )	-	0	Repeated
4.4(Contruction )	-	0	Repeated
4.6(Mass )	-	0	Repeated
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	0	Repeated
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	0	Repeated
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	0	Repeated
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	0	Repeated
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	0	Repeated

14 Jun, 2027

-
Included w.e.f. 05.01.2024

Bureau of Indian Standards

The National Standards Body of India

NATIONAL TEST HOUSE-ER (NTH), KOLKATA

BLOCK-CP, SECTOR-V,, SALT LAKE CITY, Kolkata, 24 PARAGANAS NORTH, West Bengal, 700091

9968653673 nthsal-wb@nic.in

Scope List