BIS - LIMS (Laboratory Information Management System)

Sleen India Biz venture Private Limited, Agra

RAHANKALAN ROAD, PART 295, BLOCK-A KUBERPUR, 300 METER FROM RAILWAY CROSSING CHALESHAR ROAD, Agra, Uttar Pradesh, India, 282006, Agra, Agra, Uttar Pradesh, 282006

8193022228 sleen.info@gmail.com

Scope List

Reset

150 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

Low form beaker and tall form with spout

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	1000	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	500	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	500	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	500	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	500	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	500	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2000	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	Repeated Clause
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	Repeated Clause
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	Repeated Clause
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	Repeated Clause
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	Repeated Clause
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	Repeated Clause
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	Repeated Clause
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	Repeated Clause
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	Repeated Clause
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	Repeated Clause

15 May, 2027

-
Included w.e.f.31.07.2025 Exclusion Excluding: Cl.6 Material (Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)

IS 878 (2008)

Laboratory glassware - Graduated measuring cylinders (Second Revision)

Type 1 a,Type 1b,Type 2

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1(Nominal capacity)	-	1000	-
Table-1(Overall height)	-	500	-
Table-1(Distance from top of scale to top of cylinder)	-	500	-
Table-1(Internal height to highest graduation line)	-	500	-
Table-1(Sub-divisions)	-	500	-
Table-1(capacity at lowest graduation line)	-	500	-
Cl-9.1(Wall thickness)	-	500	-
Cl-9.2(Stability)	-	500	-
Cl-9.3(Base)	-	500	-
Cl-9.4(Rim and spout)	-	500	-
Cl-9.5(Neck and stopper)	-	500	-
Cl-9.6, Table-2(Nominal capacity)	-	1000	-
Cl-9.6, Table-2(Overall height)	-	500	-
Cl-9.6, Table-2(Distance from top of scale to top of cylinder)	-	500	-
Cl-9.6, Table-2(Internal height to highest graduation line)	-	500	-
Cl-9.6, Table-2(Sub divisions)	-	500	-
Cl-9.6, Table-2(capacity at lowest graduation line)	-	500	-
Cl-10.1(Graduation)	-	500	-
Cl-10.2(Figuring)	-	500	-
Cl-11(Accuracy testing)	-	1000	-
Cl-13(Visibility of graduation lines, figures and marking)	-	500	-
Clause. 8.0(Material)	-	4000	-
Table- 1(Max. Permissible Error (Class- a))	-	500	-
Table- 1(Max. Permissible Error (Class- b))	-	500	-
Table- 2(Max. Permissible Error (Type-2))	-	500	-
Table-1(capacity at lowest graduation line)	-	0	Repeated Clause.
Cl-9.1(Wall thickness)	-	0	Repeated Clause.
Cl-9.2(Stability)	-	0	Repeated Clause.
Cl-9.3(Base)	-	0	Repeated Clause.
Cl-9.4(Rim and spout)	-	0	Repeated Clause.
Cl-9.5(Neck and stopper)	-	0	Repeated Clause.
Cl-9.6, Table-2(Nominal capacity)	-	0	Repeated Clause.
Cl-9.6, Table-2(Overall height)	-	0	Repeated Clause.
Cl-9.6, Table-2(Distance from top of scale to top of cylinder)	-	0	Repeated Clause.
Cl-9.6, Table-2(Internal height to highest graduation line)	-	0	Repeated Clause.
Cl-9.6, Table-2(Sub divisions)	-	0	Repeated Clause.
Cl-9.6, Table-2(capacity at lowest graduation line)	-	0	Repeated Clause.
Cl-10.1(Graduation)	-	0	Repeated Clause.
Cl-10.2(Figuring)	-	0	Repeated Clause.
Cl-11(Accuracy testing)	-	0	Repeated Clause.
Cl-13(Visibility of graduation lines, figures and marking)	-	0	Repeated Clause.
Clause. 8.0(Material)	-	0	Repeated Clause.
Table- 1(Max. Permissible Error (Class- a))	-	0	Repeated Clause.
Table- 1(Max. Permissible Error (Class- b))	-	0	Repeated Clause.
Table- 2(Max. Permissible Error (Type-2))	-	0	Repeated Clause.
Table-1(capacity at lowest graduation line)	-	0	Repeated Clause.
Cl-9.1(Wall thickness)	-	0	Repeated Clause.
Cl-9.2(Stability)	-	0	Repeated Clause.
Cl-9.3(Base)	-	0	Repeated Clause.
Cl-9.4(Rim and spout)	-	0	Repeated Clause.
Cl-9.5(Neck and stopper)	-	0	Repeated Clause.
Cl-9.6, Table-2(Nominal capacity)	-	0	Repeated Clause.
Cl-9.6, Table-2(Overall height)	-	0	Repeated Clause.
Cl-9.6, Table-2(Distance from top of scale to top of cylinder)	-	0	Repeated Clause.
Cl-9.6, Table-2(Internal height to highest graduation line)	-	0	Repeated Clause.
Cl-9.6, Table-2(Sub divisions)	-	0	Repeated Clause.
Cl-9.6, Table-2(capacity at lowest graduation line)	-	0	Repeated Clause.
Cl-10.1(Graduation)	-	0	Repeated Clause.
Cl-10.2(Figuring)	-	0	Repeated Clause.
Cl-11(Accuracy testing)	-	0	Repeated Clause.
Cl-13(Visibility of graduation lines, figures and marking)	-	0	Repeated Clause.
Clause. 8.0(Material)	-	0	Repeated Clause.
Table- 1(Max. Permissible Error (Class- a))	-	0	Repeated Clause.
Table- 1(Max. Permissible Error (Class- b))	-	0	Repeated Clause.
Table- 2(Max. Permissible Error (Type-2))	-	0	Repeated Clause.
Table-1(capacity at lowest graduation line)	-	0	Repeated Clause.
Cl-9.1(Wall thickness)	-	0	Repeated Clause.
Cl-9.2(Stability)	-	0	Repeated Clause.
Cl-9.3(Base)	-	0	Repeated Clause.
Cl-9.4(Rim and spout)	-	0	Repeated Clause.
Cl-9.5(Neck and stopper)	-	0	Repeated Clause.
Cl-9.6, Table-2(Nominal capacity)	-	0	Repeated Clause.
Cl-9.6, Table-2(Overall height)	-	0	Repeated Clause.
Cl-9.6, Table-2(Distance from top of scale to top of cylinder)	-	0	Repeated Clause.
Cl-9.6, Table-2(Internal height to highest graduation line)	-	0	Repeated Clause.
Cl-9.6, Table-2(Sub divisions)	-	0	Repeated Clause.
Cl-9.6, Table-2(capacity at lowest graduation line)	-	0	Repeated Clause.
Cl-10.1(Graduation)	-	0	Repeated Clause.
Cl-10.2(Figuring)	-	0	Repeated Clause.
Cl-11(Accuracy testing)	-	0	Repeated Clause.
Cl-13(Visibility of graduation lines, figures and marking)	-	0	Repeated Clause.
Clause. 8.0(Material)	-	0	Repeated Clause.
Table- 1(Max. Permissible Error (Class- a))	-	0	Repeated Clause.
Table- 1(Max. Permissible Error (Class- b))	-	0	Repeated Clause.
Table- 2(Max. Permissible Error (Type-2))	-	0	Repeated Clause.

15 May, 2027

-
Included w.e.f 28.07.2025

IS 1381 : Part 2 (2019)

Laboratory glassware - Boiling flasks: Part 2 boiling flasks with conical ground joints (Third Revision)

Conical flask,Flat-bottom flask,Round-bottom flask

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Type)	-	1000	-
4(Series of capacities)	-	2000	-
5(Material)	-	4000	-
5(Material)	-	4000	-
6(Dimensions)	-	1500	-
6(Dimensions)	-	1500	-
6(Dimensions)	-	1500	-
6(Dimensions)	-	1500	-
7(Ground glass joints)	-	500	-
8(Thermal shock endurance)	-	3000	-
9(Marking)	-	500	-
9(Marking)	-	500	-
9(Marking)	-	500	-
9(Marking)	-	500	-
3(Type)	-	0	-
4(Series of capacities)	-	0	-
5(Material)	-	0	-
5(Material)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
7(Ground glass joints)	-	0	-
8(Thermal shock endurance)	-	0	-
9(Marking)	-	0	-
9(Marking)	-	0	-
9(Marking)	-	0	-
9(Marking)	-	0	-
3(Type)	-	0	Repeated Clause.
4(Series of capacities)	-	0	Repeated Clause.
5(Material)	-	0	Repeated Clause.
5(Material)	-	0	Repeated Clause.
6(Dimensions)	-	0	Repeated Clause.
6(Dimensions)	-	0	Repeated Clause.
6(Dimensions)	-	0	Repeated Clause.
6(Dimensions)	-	0	Repeated Clause.
7(Ground glass joints)	-	0	Repeated Clause.
8(Thermal shock endurance)	-	0	Repeated Clause.
9(Marking)	-	0	Repeated Clause.
9(Marking)	-	0	Repeated Clause.
9(Marking)	-	0	Repeated Clause.
9(Marking)	-	0	Repeated Clause.
3(Type)	-	0	Repeated Clause.
4(Series of capacities)	-	0	Repeated Clause.
5(Material)	-	0	Repeated Clause.
5(Material)	-	0	Repeated Clause.
6(Dimensions)	-	0	Repeated Clause.
6(Dimensions)	-	0	Repeated Clause.
6(Dimensions)	-	0	Repeated Clause.
6(Dimensions)	-	0	Repeated Clause.
7(Ground glass joints)	-	0	Repeated Clause.
8(Thermal shock endurance)	-	0	Repeated Clause.
9(Marking)	-	0	Repeated Clause.
9(Marking)	-	0	Repeated Clause.
9(Marking)	-	0	Repeated Clause.
9(Marking)	-	0	Repeated Clause.

15 May, 2027

-
Included w.e.f 18.12.2024 Excluding : Cl 5 Material test

IS 1381 : Part 1 (2003)

Laboratory glassware - Narrow - Necked boiling flasks (Second Revision)

25 m to 10000 ml

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3, 4(Type of Flask)	-	1000	-
3.1, 4.1(Series of Nominal Capacity)	-	2500	-
3.2, 4.2(Nominal Capacity )	-	3500	-
3.3, 4.3(Material )	-	2500	-
3.4, 3.4.1 & 4.4, 4.4.1(Construction- a) Stability )	-	2500	-
3.4, 3.4.2 & 4.4, 4.4.2(Construction- b) Neck )	-	2500	-
3.5, 4.5(Dimensions (in mm) (Table 1&2))	-	2500	-
3.5.2(Neck Length)	-	2000	-
3.5.3, 4.5.2(Dimensions of base )	-	2000	-
3.5.4, 4.5.3(Wall thickness)	-	1500	-
5(Marking )	-	500	-

15 May, 2027

-
Included w.e.f 18.12.2024 Excluding Cl 3.3 Material test

IS 453 (1993)

Double Acting Spring Hinges -Specification

Double Acting Spring hinges (Mild steel, Brass)

26600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(DIMENSIONS)	-	200	-
9(PERFORMANCE TESTS)	-	11600	-
Clause 4.1(Mild Steel Sheet)	-	1500	-
Clause 4.2(Mild Steel Wire)	-	1000	-
Clause 4.3(Cast Brass)	-	2000	-
Clause 4.4(Brass Sheets)	-	2000	-
Clause 4.5(Brass Rods)	-	2500	-
Clause 4.6(Steel Wire)	-	2100	-
Clause 4.7(Phosphor Bronze Wire)	-	2100	-
Clause 5(Sizes)	-	200	-
Clause 6(Dimensions)	-	200	-
Clause 8(Finish)	-	200	-
Clause 9(Performance Test)	-	11600	-
Clause 10(Marking)	-	100	-
Clause 11(Packing)	-	100	-
Cl-7.1(Mild Steel Hinges)	-	200	-
Cl-7.1.1(Blank hinge shall be made from mild steel sheet)	-	200	-
Cl-7.2(Brass Hinges)	-	200	-
Cl-7.2.1(Blank hinges shall be made of cast brass)	-	200	-
Clause-9.0(Performance Test)	-	11600	-
6(DIMENSIONS)	-	0	Repeated Clause.
9(PERFORMANCE TESTS)	-	0	Repeated Clause.
Clause 4.1(Mild Steel Sheet)	-	0	Repeated Clause.
Clause 4.2(Mild Steel Wire)	-	0	Repeated Clause.
Clause 4.3(Cast Brass)	-	0	Repeated Clause.
Clause 4.4(Brass Sheets)	-	0	Repeated Clause.
Clause 4.5(Brass Rods)	-	0	Repeated Clause.
Clause 4.6(Steel Wire)	-	0	Repeated Clause.
Clause 4.7(Phosphor Bronze Wire)	-	0	Repeated Clause.
Clause 5(Sizes)	-	0	Repeated Clause.
Clause 6(Dimensions)	-	0	Repeated Clause.
Clause 8(Finish)	-	0	Repeated Clause.
Clause 9(Performance Test)	-	0	Repeated Clause.
Clause 10(Marking)	-	0	Repeated Clause.
Clause 11(Packing)	-	0	Repeated Clause.
Cl-7.1(Mild Steel Hinges)	-	0	Repeated Clause.
Cl-7.1.1(Blank hinge shall be made from mild steel sheet)	-	0	Repeated Clause.
Cl-7.2(Brass Hinges)	-	0	Repeated Clause.
Cl-7.2.1(Blank hinges shall be made of cast brass)	-	0	Repeated Clause.
Clause-9.0(Performance Test)	-	0	Repeated Clause.

15 May, 2027

-
Included w.e.f 03.03.2025

IS 3843 (1995)

Steel back flap hinges -Specification

Light weight Hinges , Heavy weight Hinges

4200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 6, Table 1, Table 2(Dimensions)	-	1000	-
Clause 4 Table 3(i)(Flap)	-	1000	-
Clause 4 Table 3(ii)(Pin)	-	1000	-
Clause 5(Dimension and tolerance)	-	1000	-
Clause 8(Marking)	-	100	-
Clause 9(Packing)	-	100	-
5, 6, Table 1, Table 2(Dimensions)	-	0	Repeated Clause.
Clause 4 Table 3(i)(Flap)	-	0	Repeated Clause.
Clause 4 Table 3(ii)(Pin)	-	0	Repeated Clause.
Clause 5(Dimension and tolerance)	-	0	Repeated Clause.
Clause 8(Marking)	-	0	Repeated Clause.
Clause 9(Packing)	-	0	Repeated Clause.

15 May, 2027

-
Included w.e.f 03.03.2025

IS 3818 (1992)

Continuous (Piano) hinges -Specification

Type I,Type II,Type III,Type IV

5600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 (Ref. Cl.9 of IS 1868:1996)(Anodic casting thickness (Cl. 9.2 of IS 1868:1996))	-	1000	-
4-Fig 1(DIMENSIONS AND TOLERANCES-Nominal Size)	-	100	-
4-Fig 1(DIMENSIONS AND TOLERANCES-B)	-	100	-
4-Fig 1(DIMENSIONS AND TOLERANCES-C)	-	100	-
4-Fig 1(DIMENSIONS AND TOLERANCES-D)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-T)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES- Other Dimensions)	-	200	-
4-Fig 2(DIMENSIONS AND TOLERANCES-CoNTINUOUS ( PIANO) HINGIS TYPB III; 50 min NOMINAL SID)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B1)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B2)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-C)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-D)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-T)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	200	-
5.1(MANUFACTURE)	-	100	-
5.2(MANUFACTURE-Knuekles)	-	100	-
5.2(MANUFACTURE-Knuekles)	-	100	-
5.3(MANUFACTURE-Pins)	-	100	-
5.3(MANUFACTURE-Pins)	-	100	-
5.3(MANUFACTURE-Pin-Anodized thickness)	-	1000	-
5.3(MANUFACTURE-Pins)	-	100	-
5.4(MANUFACTURE-Screw Holes)	-	100	-
6(Finish)	-	1000	-
Cl. 6 (Ref. Cl.9 of IS 1868:1996)(Anodic casting thickness (Cl. 9.2 of IS 1868:1996))	-	1000	-
4-Fig 1(DIMENSIONS AND TOLERANCES-Nominal Size)	-	100	-
4-Fig 1(DIMENSIONS AND TOLERANCES-B)	-	100	-
4-Fig 1(DIMENSIONS AND TOLERANCES-C)	-	100	-
4-Fig 1(DIMENSIONS AND TOLERANCES-D)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-T)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES- Other Dimensions)	-	200	-
4-Fig 2(DIMENSIONS AND TOLERANCES-CoNTINUOUS ( PIANO) HINGIS TYPB III; 50 min NOMINAL SID)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B1)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B2)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-C)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-D)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-T)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	200	-
5.1(MANUFACTURE)	-	100	-
5.2(MANUFACTURE-Knuekles)	-	100	-
5.2(MANUFACTURE-Knuekles)	-	100	-
5.3(MANUFACTURE-Pins)	-	100	-
5.3(MANUFACTURE-Pins)	-	100	-
5.3(MANUFACTURE-Pin-Anodized thickness)	-	1000	-
5.3(MANUFACTURE-Pins)	-	100	-
5.4(MANUFACTURE-Screw Holes)	-	100	-
6(Finish)	-	1000	-
Cl. 6 (Ref. Cl.9 of IS 1868:1996)(Anodic casting thickness (Cl. 9.2 of IS 1868:1996))	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-Nominal Size)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-B)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-C)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-D)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-T)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES- Other Dimensions)	-	0	Repeated Clause.
4-Fig 2(DIMENSIONS AND TOLERANCES-CoNTINUOUS ( PIANO) HINGIS TYPB III; 50 min NOMINAL SID)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-B)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-B1)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-B2)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-C)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-D)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-T)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	0	Repeated Clause.
5.1(MANUFACTURE)	-	0	Repeated Clause.
5.2(MANUFACTURE-Knuekles)	-	0	Repeated Clause.
5.2(MANUFACTURE-Knuekles)	-	0	Repeated Clause.
5.3(MANUFACTURE-Pins)	-	0	Repeated Clause.
5.3(MANUFACTURE-Pins)	-	0	Repeated Clause.
5.3(MANUFACTURE-Pin-Anodized thickness)	-	0	Repeated Clause.
5.3(MANUFACTURE-Pins)	-	0	Repeated Clause.
5.4(MANUFACTURE-Screw Holes)	-	0	Repeated Clause.
6(Finish)	-	0	Repeated Clause.
Cl. 6 (Ref. Cl.9 of IS 1868:1996)(Anodic casting thickness (Cl. 9.2 of IS 1868:1996))	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-Nominal Size)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-B)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-C)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-D)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-T)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap)	-	0	Repeated Clause.
4-Fig 1(DIMENSIONS AND TOLERANCES- Other Dimensions)	-	0	Repeated Clause.
4-Fig 2(DIMENSIONS AND TOLERANCES-CoNTINUOUS ( PIANO) HINGIS TYPB III; 50 min NOMINAL SID)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-B)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-B1)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-B2)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-C)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-D)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-T)	-	0	Repeated Clause.
4-Fig 3(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	0	Repeated Clause.
5.1(MANUFACTURE)	-	0	Repeated Clause.
5.2(MANUFACTURE-Knuekles)	-	0	Repeated Clause.
5.2(MANUFACTURE-Knuekles)	-	0	Repeated Clause.
5.3(MANUFACTURE-Pins)	-	0	Repeated Clause.
5.3(MANUFACTURE-Pins)	-	0	Repeated Clause.
5.3(MANUFACTURE-Pin-Anodized thickness)	-	0	Repeated Clause.
5.3(MANUFACTURE-Pins)	-	0	Repeated Clause.
5.4(MANUFACTURE-Screw Holes)	-	0	Repeated Clause.
6(Finish)	-	0	Repeated Clause.

15 May, 2027

-
Included w.e.f 03.03.2025

IS 206 (2010)

Tee and strap hinges - Specification (Fifth Revision)

Tee and Strap Hinges

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(DIMENSIONS AND TOLERANCES)	-	500	-
6(WORKMANSHIP)	-	100	-
7(FINISH)	-	100	-
10(MARKING)	-	100	-
Clause 3.1,1(Light weight (Type 1))	-	500	-
Clause 3.1,2(Light weight (Type 2))	-	500	-
Clause 3.1,3(Medium weight (Type 1))	-	500	-
Clause 3.1,4(Medium weight (Type 2))	-	500	-
Clause 3.1,5(Heavy weight (Type 1))	-	500	-
Clause 3.1,6(Heavy weight (Type 2))	-	500	-
Clause 3.1,7(Heavy weight (Type 3))	-	500	-
Clause 3.2,1(Light weight)	-	500	-
Clause 3.2,2(Medium weight (Type 1))	-	500	-
Clause 3.2,3(Medium weight (Type 2))	-	500	-
Clause 3.2,4(Heavy weight )	-	500	-
Clause 4 Table 1(i)(Mild steel sheet)	-	500	-
Clause 4 Table 1(ii)(Mild steel wire)	-	500	-
Clause 5.1(Dimensions)	-	500	-
Clause 6(Workmanship)	-	100	-
Clause 8(Packing)	-	100	-
Clause 9(SAMPLING AND CRITERION FOR CONFORMITY)	-	100	-
Clause 10(Marking)	-	100	-
5(DIMENSIONS AND TOLERANCES)	-	0	Repeated clause.
6(WORKMANSHIP)	-	0	Repeated clause.
7(FINISH)	-	0	Repeated clause.
10(MARKING)	-	0	Repeated clause.
Clause 3.1,1(Light weight (Type 1))	-	0	Repeated clause.
Clause 3.1,2(Light weight (Type 2))	-	0	Repeated clause.
Clause 3.1,3(Medium weight (Type 1))	-	0	Repeated clause.
Clause 3.1,4(Medium weight (Type 2))	-	0	Repeated clause.
Clause 3.1,5(Heavy weight (Type 1))	-	0	Repeated clause.
Clause 3.1,6(Heavy weight (Type 2))	-	0	Repeated clause.
Clause 3.1,7(Heavy weight (Type 3))	-	0	Repeated clause.
Clause 3.2,1(Light weight)	-	0	Repeated clause.
Clause 3.2,2(Medium weight (Type 1))	-	0	Repeated clause.
Clause 3.2,3(Medium weight (Type 2))	-	0	Repeated clause.
Clause 3.2,4(Heavy weight )	-	0	Repeated clause.
Clause 4 Table 1(i)(Mild steel sheet)	-	0	Repeated clause.
Clause 4 Table 1(ii)(Mild steel wire)	-	0	Repeated clause.
Clause 5.1(Dimensions)	-	0	Repeated clause.
Clause 6(Workmanship)	-	0	Repeated clause.
Clause 8(Packing)	-	0	Repeated clause.
Clause 9(SAMPLING AND CRITERION FOR CONFORMITY)	-	0	Repeated clause.
Clause 10(Marking)	-	0	Repeated clause.
5(DIMENSIONS AND TOLERANCES)	-	0	Repeated clause.
6(WORKMANSHIP)	-	0	Repeated clause.
7(FINISH)	-	0	Repeated clause.
10(MARKING)	-	0	Repeated clause.
Clause 3.1,1(Light weight (Type 1))	-	0	Repeated clause.
Clause 3.1,2(Light weight (Type 2))	-	0	Repeated clause.
Clause 3.1,3(Medium weight (Type 1))	-	0	Repeated clause.
Clause 3.1,4(Medium weight (Type 2))	-	0	Repeated clause.
Clause 3.1,5(Heavy weight (Type 1))	-	0	Repeated clause.
Clause 3.1,6(Heavy weight (Type 2))	-	0	Repeated clause.
Clause 3.1,7(Heavy weight (Type 3))	-	0	Repeated clause.
Clause 3.2,1(Light weight)	-	0	Repeated clause.
Clause 3.2,2(Medium weight (Type 1))	-	0	Repeated clause.
Clause 3.2,3(Medium weight (Type 2))	-	0	Repeated clause.
Clause 3.2,4(Heavy weight )	-	0	Repeated clause.
Clause 4 Table 1(i)(Mild steel sheet)	-	0	Repeated clause.
Clause 4 Table 1(ii)(Mild steel wire)	-	0	Repeated clause.
Clause 5.1(Dimensions)	-	0	Repeated clause.
Clause 6(Workmanship)	-	0	Repeated clause.
Clause 8(Packing)	-	0	Repeated clause.
Clause 9(SAMPLING AND CRITERION FOR CONFORMITY)	-	0	Repeated clause.
Clause 10(Marking)	-	0	Repeated clause.
5(DIMENSIONS AND TOLERANCES)	-	0	Repeated clause.
6(WORKMANSHIP)	-	0	Repeated clause.
7(FINISH)	-	0	Repeated clause.
10(MARKING)	-	0	Repeated clause.
Clause 3.1,1(Light weight (Type 1))	-	0	Repeated clause.
Clause 3.1,2(Light weight (Type 2))	-	0	Repeated clause.
Clause 3.1,3(Medium weight (Type 1))	-	0	Repeated clause.
Clause 3.1,4(Medium weight (Type 2))	-	0	Repeated clause.
Clause 3.1,5(Heavy weight (Type 1))	-	0	Repeated clause.
Clause 3.1,6(Heavy weight (Type 2))	-	0	Repeated clause.
Clause 3.1,7(Heavy weight (Type 3))	-	0	Repeated clause.
Clause 3.2,1(Light weight)	-	0	Repeated clause.
Clause 3.2,2(Medium weight (Type 1))	-	0	Repeated clause.
Clause 3.2,3(Medium weight (Type 2))	-	0	Repeated clause.
Clause 3.2,4(Heavy weight )	-	0	Repeated clause.
Clause 4 Table 1(i)(Mild steel sheet)	-	0	Repeated clause.
Clause 4 Table 1(ii)(Mild steel wire)	-	0	Repeated clause.
Clause 5.1(Dimensions)	-	0	Repeated clause.
Clause 6(Workmanship)	-	0	Repeated clause.
Clause 8(Packing)	-	0	Repeated clause.
Clause 9(SAMPLING AND CRITERION FOR CONFORMITY)	-	0	Repeated clause.
Clause 10(Marking)	-	0	Repeated clause.
5(DIMENSIONS AND TOLERANCES)	-	0	Repeated clause.
6(WORKMANSHIP)	-	0	Repeated clause.
7(FINISH)	-	0	Repeated clause.
10(MARKING)	-	0	Repeated clause.
Clause 3.1,1(Light weight (Type 1))	-	0	Repeated clause.
Clause 3.1,2(Light weight (Type 2))	-	0	Repeated clause.
Clause 3.1,3(Medium weight (Type 1))	-	0	Repeated clause.
Clause 3.1,4(Medium weight (Type 2))	-	0	Repeated clause.
Clause 3.1,5(Heavy weight (Type 1))	-	0	Repeated clause.
Clause 3.1,6(Heavy weight (Type 2))	-	0	Repeated clause.
Clause 3.1,7(Heavy weight (Type 3))	-	0	Repeated clause.
Clause 3.2,1(Light weight)	-	0	Repeated clause.
Clause 3.2,2(Medium weight (Type 1))	-	0	Repeated clause.
Clause 3.2,3(Medium weight (Type 2))	-	0	Repeated clause.
Clause 3.2,4(Heavy weight )	-	0	Repeated clause.
Clause 4 Table 1(i)(Mild steel sheet)	-	0	Repeated clause.
Clause 4 Table 1(ii)(Mild steel wire)	-	0	Repeated clause.
Clause 5.1(Dimensions)	-	0	Repeated clause.
Clause 6(Workmanship)	-	0	Repeated clause.
Clause 8(Packing)	-	0	Repeated clause.
Clause 9(SAMPLING AND CRITERION FOR CONFORMITY)	-	0	Repeated clause.
Clause 10(Marking)	-	0	Repeated clause.

15 May, 2027

-
Included w.e.f 28.07.2025

IS 17043 : Part 2 (2024)

Shoes: Shoes for General Purpose

Shoes for General Purpose

78400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Shape and Design)	-	100	10% Discount on BIS Sample.
Cl-5.3(Material)	-	100	10% Discount on BIS Sample.
Cl-5.4, Table-1 (i)(Bond strength, N/mm, Min Upper to outsole, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (ii)(Inter layer bond strength,= N/mm, Min Midsole to outsole, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (iii)(Whole shoe flexing, flexes)	-	1000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (iv)(Water proofness on complete shoe)	-	1000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (v)(Slip resistance, Cof(1), Min dry and wet* (quarry tile))	-	1800	10% Discount on BIS Sample.
Cl-5.4, Table-1 (vi)(Attachment strength of strap and buckle/D-ring N)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (vii)(Attachment strength of strap and velcro , N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (viii)(Strength of eyelet attachment, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (ix)(Heel pull off strength, N, Min)	-	700	10% Discount on BIS Sample.
Cl-5.4, Table-1 (x)(Top piece attachment strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xi)(Seam strength, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xii)(Whole shoe topline strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xiii)(Abrasion resistance (volume loss), mm3)	-	850	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xiv)(Chemical requirements(3))	-	30000	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xv)(Lead content (as Pb) ppm, Max)	-	500	10% Discount on BIS Sample.
Cl-5.4, Table-1 (xvi)(Hydrolysis resistance,(4) cut growth at 150 000 flexes, mm, Max)	-	1800	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (i)(Tear trength, N)	-	600	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (ii)(Flexing resistance, flexes)	-	800	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (iii)(Colour fastness to rubbing (marring/staining))	-	500	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (iv)(Colour fastness to water (contact method- multi fabrics))	-	400	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (v)(Water vapour permeability,mg/cm2 /h, Min Water vapour coefficient,mg/cm2 , Min)	-	800	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (vi)(Stitch tear strength, N/mm, Min)	-	500	10% Discount on BIS Sample.
Cl-6.1.1, Table-2 (vii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (i)(Colour fastness to light, Marring, Min)	-	700	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (ii)(Water resistance)	-	800	10% Discount on BIS Sample.
Cl-6.1.2, Table-3 (iii)(Flexing resistance, flexes at (-) 5 °C 25 000 flexes)	-	1200	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (i)(Breaking strength, N/mm, Min Elongation at break, percent, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (ii)(Tear Strength, N, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (iii)(Strength at needle perforation, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (iv)(Flexing resistance, Flexes)	-	800	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (v)(Water vapour permeability (WVP), mg/cm2 /h, Min)	-	800	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (vi)(Hydrolysis resistance)	-	1800	10% Discount on BIS Sample.
Cl-6.1.3, Table- 4 (vii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.1.4, Table-5 (i)(Colour fastness to light, Marring, Min)	-	800	10% Discount on BIS Sample.
Cl-6.1.4, Table- 5 (ii)(Flexing resistance, flexes at (-) 5 ºC, s 25 000 flexes)	-	1200	10% Discount on BIS Sample.
Cl-6.2, Table-6 (i)(Tear strength, N, Min)	-	600	10% Discount on BIS Sample.
Cl-6.2, Table-6 (ii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.2, Table-6 (iii)(Colour fastness rubbing (crocking))	-	300	10% Discount on BIS Sample.
Cl-6.2, Table-6 (iv)(Colour fastness to perspiration)	-	400	10% Discount on BIS Sample.
Cl-6.2, Table-6 (v)(Water vapour permeability, mg/cm2 /h, Min Water vapour coefficient, mg/cm2, Min)	-	800	10% Discount on BIS Sample.
Cl-6.3, Table-7 (i)(Flexing index, Min)	-	800	10% Discount on BIS Sample.
Cl-6.3, Table-7 (ii)(Abrasion resistance at 400 cycles)	-	300	10% Discount on BIS Sample.
Cl-6.3, Table-7 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	800	10% Discount on BIS Sample.
Cl-6.4, Table-8 (i)(Thickness, mm, Min)	-	100	10% Discount on BIS Sample.
Cl-6.4, Table-8 (ii)(Abrasion resistance)	-	1000	10% Discount on BIS Sample.
Cl-6.4, Table-8 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	800	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (i)(Flexing resistance)	-	800	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (ii)(Hydrolysis resistance, cut growth at 150 000 flexes, mm, Max)	-	1800	10% Discount on BIS Sample.
Cl-6.5.1, , Table-9 (iii)(Compression set, percent, Max)	-	500	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (i)(Grain crack index, Min)	-	500	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (ii)(Density, g/cm3 , Min)	-	200	10% Discount on BIS Sample.
Cl-6.5.2.1, Table-10 (iii)(Abrasion resistance, mm/kcs, Max)	-	800	10% Discount on BIS Sample.
Cl-6.5.2.2, Table-11 (i)(Water resistance, (dynamic method))	-	1000	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (i)(Hardness, Min)	-	200	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (ii)(Density, g/cm3 , Max)	-	200	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (iii)(Abrasion resistance (volume loss), mm3 , Max)	-	850	10% Discount on BIS Sample.
Cl-6.5.2.3, Table-12 (iv)(Bond Strength between Rubber top-lift and adjacent material, N/mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.6, Table-13 (i)(Heat shrinkage, percent, Max)	-	300	10% Discount on BIS Sample.
Cl-6.6, Table-13 (ii)(Split tear strength, kg/25 mm, Min)	-	600	10% Discount on BIS Sample.
Cl-6.6, Table-13 (iii)(Compression set, percent, Max)	-	500	10% Discount on BIS Sample.
Cl-6.7, Table-14 (i)(Hardness, N)	-	300	10% Discount on BIS Sample.
Cl-6.7, Table-14 (ii)(Resilience, percent)	-	300	10% Discount on BIS Sample.
Cl-6.7, Table-14 (iii)(Moisture resistance, percent)	-	300	10% Discount on BIS Sample.
Cl-6.10, Table-17 (i)(Lace breaking strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-6.10, Table-17 (ii)(Lace tag strength, N, Min)	-	500	10% Discount on BIS Sample.
Cl-6.10, Table-17 (iii)(Lace to lace abrasion resistance, cycles)	-	500	10% Discount on BIS Sample.
Cl-6.10, Table-17 (iv)(Colour fastness to water for lace contact methodstaining Gray scale rate , Min)	-	300	10% Discount on BIS Sample.
Cl-6.10, Table-17 (v)(Corrosion resistance)	-	300	10% Discount on BIS Sample.
Cl-6.11, Table-18 (i)(Fatigue resistance, cycles, Min)	-	700	10% Discount on BIS Sample.
Cl-6.11, Table-18 (ii)(Security of puller attachment strength, N, Min)	-	300	10% Discount on BIS Sample.
Cl-6.11, Table-18 (iii)(Lateral load, N, Min)	-	300	10% Discount on BIS Sample.
Cl-6.11, Table-18 (iv)(End attachment strength, N, Min)	-	300	10% Discount on BIS Sample.
Cl-8.1(Marking)	-	0	-

15 May, 2027

-
Included w.e.f. 04.04.2024 Exclusion: Cl-6.5.2.2, S.No (1), i (Water resistance, (dynamic method))

100

IS 863 (2023)

Medical Textiles - Cotton bandage cloth - Specification third revision of IS 863

Medical Textiles — Cotton Bandage Cloth

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Fibre Identification)	-	400	10% Discount on BIS Samples.
4.2, Table 1, i)(Count of yarn (for guidance only))	-	200	10% Discount on BIS Samples.
4.2, Table 1, ii)(Threads, dm, Min)	-	200	10% Discount on BIS Samples.
4.2, Table 1, iii)(Mass, g/m2)	-	300	10% Discount on BIS Samples.
4.2, Table 1, iv)(Length, m, tolerance)	-	100	10% Discount on BIS Samples.
4.2, Table 1, v)(Width, m, tolerance)	-	100	10% Discount on BIS Samples.
4.2, Table 1, vi)(pH value of acqueous extract)	-	300	10% Discount on BIS Samples.
4.2, Table 1, vii)(Scouring loss, percent, Max)	-	300	10% Discount on BIS Samples.
4.2, Table 1, viii)(Freedom from optical whiteners)	-	500	10% Discount on BIS Samples.
4.2, Table 1, ix)(Colour fastness: a) Light)	-	800	10% Discount on BIS Samples.
4.2, Table 1, ix)(Colour fastness: b) Washing (A1))	-	400	10% Discount on BIS Samples.
4.2, Table 1, x)(Sterility (optional))	-	800	10% Discount on BIS Samples.
6(Marking)	-	100	10% Discount on BIS Samples.

15 May, 2027

-
Included w.e.f 15.07.2024 Exclusion: 4.2, Table 1, x) (Sterility (optional))

101

IS 17423 (2021)

Medical Textiles Bio-Protective Coveralls Specification (First Revision)

12300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1, Table-1 (i)(Resistance to penetration by blood and body fluids (synthetic blood penetration resistance), procedure d (see note 1))	-	2000	10% Discount for BIS
Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1, Table-1, (ii)(Resistance to penetration by blood borne pathognes (resistance to viral penetration), procedure d (see note 1))	-	1000	10% Discount for BIS
Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1, Table-1 (iii)(Breathability (water vapour transmission rate), g/m2/day, Max)	-	500	10% Discount for BIS
Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1, Table-1 (iv)(Tensile strength (dry and wet) (N))	-	800	10% Discount for BIS
Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1, Table-1 (v)(Seam strength (dry and wet) (N) (see note 2))	-	500	10% Discount for BIS
Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1 Table-1 (vi)(Bursting strength (dry and wet) (kPa))	-	2500	10% Discount for BIS
Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1, Table-1 (vii)(Cleanliness-microbial (CFU/100 cm2))	-	2500	10% Discount for BIS
Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1, Table-1 (viii)(Resistance to dry microbial penetration ,(log cfu) (At challenge concentration 108 CFU/g talcum and 30 min vibration time))	-	2500	10% Discount for BIS

15 May, 2027

-
Included w.e.f. 07.08.2024 Exclusion: Cl- 4.4, 5.2, 5.3, 5.4, 5.5 and 7.1,Table-1 (ix) (Biocompatibility evaluation- Cytotoxicity, Irritation and skin sensitization) and Table-1 (ii) (Resistance to penetration by blood borne pathognes (resistance to viral penetration)

102

IS 3617 (2022)

Textiles Gents pullover knitted Specification Second Revision

13750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Class of Pullover)	-	250	10% Discount for BIS
4.2(Conformity of Yarn)	-	250	10% Discount for BIS
4.3(Conformity of Fabric)	-	250	10% Discount for BIS
4.4(Seams and Stitches)	-	250	10% Discount for BIS
4.5(Pullover – Shape, Welt (or tape), Border, High neck portion, reinforcements, freedom from defects)	-	250	10% Discount for BIS
5.1(Dimension and Tolerance)	-	500	10% Discount for BIS
5.2, Table 2(i) Construction)	-	250	10% Discount for BIS
5.2 Table 2(ii) Dimensional change)	-	500	10% Discount for BIS
5.2 Table 2(iii) Scouring loss)	-	500	10% Discount for BIS
5.2 Table 2(iv) Alkali Solubility)	-	500	10% Discount for BIS
5.2 Table 2(v) pH value of aqueous extract)	-	500	10% Discount for BIS
5.2 Table 2(vi) Minimum colour fastness ratings)	-	2500	10% Discount for BIS
5.2 Table 2(vii) Fibre composition)	-	1000	10% Discount for BIS
5.2 Table 2(viii) Fineness grade of wool (wollen pullover))	-	1000	10% Discount for BIS
6(Marking)	-	250	10% Discount for BIS
7(Packing)	-	250	10% Discount for BIS
4.1(Class of Pullover)	-	250	10% Discount for BIS
4.2(Yarn)	-	250	10% Discount for BIS
4.2.1("Yarn - The hosiery yarn, shall be 100 percent virgin wool, or 100 percent acrylic fibres, or blends of wool with acrylic fibres and/or polyester fibres (or)viscose rayon and polyamide (nylon) fibres")	-	500	10% Discount for BIS
4.3.1(Fabric - Moth Proofing)	-	500	10% Discount for BIS
4.3.2(Fabric - Shrink-proof)	-	500	10% Discount for BIS
4.4(Seams and Stitches)	-	250	10% Discount for BIS
4.4.1(All stitches made from one strand of sewing thread conforming to any one of the appropriate varieties)	-	250	10% Discount for BIS
4.4.2("In case of single colour pullover, same colour threads for stitching, in case of multi-colour pullover threads shall be of the major or ground colour")	-	250	10% Discount for BIS
4.4.3(The number of stitches shall not be less than 4 per cm)	-	250	10% Discount for BIS
4.5.1(Pullover shall be made of one piece with cuffs at sleeves and border at the bottom. welt at the neck shall be attached to the pullover by stitching or linking)	-	250	10% Discount for BIS
4.5.2(The pullover shall be of V-neck, round-reek or high-neck)	-	250	10% Discount for BIS
4.5.3(Welt (or Tape))	-	250	10% Discount for BIS
4.5.4(Border)	-	250	10% Discount for BIS
4.5.5(High Neck Portion)	-	250	10% Discount for BIS
4.5.6("All stitches shall be of even tension throughout with all the loose ends securely fastened. Stitching shall not give way when the pullover is stretched to one and a half times")	-	250	10% Discount for BIS
4.5.7(Freedom from Defects)	-	250	10% Discount for BIS
5.1(REQUIREMENTS - dimensions of the pullover)	-	0	NA
5.2- Table 2 i)(REQUIREMENTS - Construction a) Wales per 5 cm b) Courses per 5 cm)	-	0	NA
5.2- Table 2 ii)(REQUIREMENTS - Dimensional change (due to relaxation) percent)	-	0	NA
5.2- Table 2 iii)(REQUIREMENTS - Scouring loss, percent)	-	0	NA
5.2- Table 2 iv)("REQUIREMENTS - Alkali, solubility, percent, Max (not applicable for 100 percent acrylic) a) Bleached b) Dyed/mixed shade")	-	0	NA
5.2- Table 2 v)("REQUIREMENTS - pH value of aqueous extract a) All wool i) Bleached and stoved shaded ii) Other shades b) Acrylic or blended")	-	0	NA
5.2- Table 2 vi)("REQUIREMENTS - Minimum colour fastness rating a) Light b) Washing: Test A(1) i) Change in colour ii) Staining of adjacent fabric c) Rubbing (Dry and wet) d) Dry-cleaning")	-	0	NA
5.2- Table 2 vii)(REQUIREMENTS - Fibre composition, percent)	-	0	NA
5.2- Table 2 viii)(REQUIREMENTS - Fineness grade of wool (woollen pullover))	-	0	NA
6(MARKING)	-	0	NA
7(PACKING)	-	0	NA

15 May, 2027

-
Included w.e.f. 09.05.2024

103

IS 170 (2020)

Acetone — Specification ( Fifth Revision )

11700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	200	10% Discount on BIS Sample.
3.2(Miscibility with Water)	-	300	10% Discount on BIS Sample.
4.1(Packing)	-	100	10% Discount on BIS Sample.
4.2(Marking)	-	100	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 1(Purity %, Annex A)	-	2500	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 2(Colour, Pt-Co scale, IS 8768)	-	1500	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 3(Relative density, 6 of IS 82)	-	500	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 4(Distillation range, IS 1448-Part 18)	-	500	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 5(Water content, %, IS 2362)	-	500	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 6(Residue on evaporation, mg/ 100 ml, 8 of IS 82)	-	500	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 7(Acidity, g/100 ml, Annex C)	-	1000	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 8(Alkalinity, Annex D)	-	1000	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 9(Permanganate test, minutes, Annex E)	-	500	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 10(Alcoholic impurities, Annex F)	-	500	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 11(Benzene content mg/kg, Annex A)	-	1000	10% Discount on BIS Sample.
3.3 & 6.1 - Table -1, Sl no. 12(Methanol content mg/kg, Annex A)	-	1000	10% Discount on BIS Sample.
Cl No 3.1( Description)	-	0	NA
Cl No 3.2(Miscibility with Water)	-	0	NA
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (i) ](Purity)	-	0	NA
Cl 3.3 and 6.1 [ Table 1, Sl No. (ii) ] ref to IS 8768(Colour)	-	0	NA
Cl 3.3 and 6.1 [ Table 1, Sl No. (iii) ] ref to 6 of IS 82(Relative density, at 27/27 °C)	-	0	NA
Cl 3.3 and 6.1 [ Table 1, Sl No. (iv) ] IS 1448 (Part 18) with the thermometer containing to the requirements given to Annex B(*Distillation range)	-	0	NA
Cl 3.3 and 6.1 [ Table 1, Sl No. (v) ] ref to IS 2362(Water content)	-	0	NA
Cl 3.3 and 6.1 [ Table 1, Sl No. (vi) ] ref to 8 of IS 82(Residue on evaporation)	-	0	NA
Cl 3.3 and 6.1 ANNEX C [ Table 1, Sl No. (vii) ](Acidity (as CH3COOH),)	-	0	NA
Cl 3.3 and 6.1 ANNEX D [ Table 1, Sl No. (viii) ](Alkalinity)	-	0	NA
Cl 3.3 and 6.1 ANNEX E [ Table 1, Sl No. (ix) ](Permanganate test)	-	0	NA
Cl 3.3 and 6.1 ANNEX F [ Table 1, Sl No. (x) ](Alcoholic impurities)	-	0	NA
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (xi) ](Benzene content)	-	0	NA
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (xii) ](Methanol content)	-	0	NA

15 May, 2027

-
-

104

IS 2052 (2023)

Compounded feeds for cattle ï¿½ Specification

15050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl no.4.1(General)	-	100	10% discount for BIS
Cl no.4.2(Ingredients)	-	100	10% discount for BIS
Cl no.4.3,7.1, Table no. 1(i)(Moisture)	-	500	10% discount for BIS
Cl no.4.3,7.1, Table no. 1(ii)(Crude protein (N × 6.25))	-	750	10% discount for BIS
Cl no.4.3, 7.1,Table no. 1(iii)(Crude fat)	-	750	10% discount for BIS
Cl no.4.3 ,7.1, Table no. 1(iv)(Crude fibre)	-	1000	10% discount for BIS
Cl no.4.3 ,7.1, Table no. 1(v)(Acid insoluble ash)	-	600	10% discount for BIS
Cl no.4.3,7.1Table no. 1(vi)("Salt (as NaCl based on Na or Cl), percent by mass")	-	500	10% discount for BIS
Cl no.4.3 7.1,Table no. 1(vii)(Calcium (as Ca))	-	500	10% discount for BIS
Cl no.4.3,7.1,Table no. 1(viii)(Total phosphorus)	-	800	10% discount for BIS
Cl no.4.3,7.1,Table no. 1(ix)(Available phosphorus)	-	800	10% discount for BIS
Cl no.4.3 ,7.1, Table no. 1(x)(Urea, percent by mass)	-	500	10% discount for BIS
Cl no.4.3,7.1, Table no. 1(xi)(Vitamin A)	-	1800	10% discount for BIS
Cl no.4.3,7.1,Table no. 1(xii)(Vitamin D)	-	1800	10% discount for BIS
Cl no.4.3 ,7.1, Table no. 1(xiii)(Vitamin E)	-	1800	10% discount for BIS
Cl no.4.3 ,7.1, Table no. 1(xiv)(Aflatoxin B1)	-	2000	10% discount for BIS
Cl no.4.3 ,7.1, Table no. 1(xv)(Cadmium)	-	500	10% discount for BIS
Cl no.5(Packing and marking)	-	250	10% discount for BIS
4.1(General)	-	0	NA
4.2.2(Ratio of total nitrogen to sulphur/ IS/ISO 5983 (Part 1)* or IS/ISO 5983 (Part 2) ISO 16634-Sulphur-AnnexB (IS 1664 or EN 15621))	-	0	NA
4.3 Table no.1 (i)(Moisture/4 of IS 7874 (Part 1))	-	0	NA
4.3 Table no.1 (ii)("Crude Protein(ODB)/IS/ISO 5983 (Part 1)* or IS 5983 (Part 2) or ISO 16634-1")	-	0	NA
4.3 Table no.1 (iii)(Crude fat (ODB) /IS/ISO 6492)	-	0	NA
4.3 Table no.1 (iv)("Crude fibre (ODB)/IS/ISO 6865 ")	-	0	NA
4.3 Table no.1 (v)(Acid insoluble ash (ODB)/Annex A of IS 1712 or IS 14826*)	-	0	NA
4.3 Table no.1 (vi)("Salt (ODB)(as NaCl based on Na or Cl)/4 of IS 7874 (Part 2)")	-	0	NA
4.3 Table no.1 (vii)(Calcium(ODB) (as Ca)/IS 13433 (Part 1) or IS 15121* or EN 15621)	-	0	NA
4.3 Table no.1 (viii)(Total phosphorus (ODB)/IS 14828* or EN 15621)	-	0	NA
4.3 Table no.1 (ix)(Available phosphorus (ODB)/Annex F of IS 1374)	-	0	NA
4.3 Table no.1 (x)(Urea (ODB)/IS 7874 (Part 1) or AOAC 967.07)	-	0	NA
4.3 Table no.1 (xi)(Vitamin A(ODB)/IS 15120)	-	0	NA
4.3 Table no.1 (xii)("Vitamin D3 (ODB)/Annex C * or J. AOAC Int. 2012, Vol. 95, No. 5, Pages 1487–1494")	-	0	NA
4.3 Table no.1 (xiii)(Vitamin E(ODB)/IS 15948)	-	0	NA
4.3 Table no.1 (xiv)("Aflatoxin B1 (ODB)/IS/ISO 14718* or ISO 17375 or AOAC 2003.02")	-	0	NA
4.3 Table no.1 (xv)(Cadmium (ODB)/EN 17053)	-	0	NA

15 May, 2027

-
Included w.e.f. 02.04.2024

105

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

7650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	200	Bis sample 10% discount
5/5.5- Table1(REQUIREMENTS-Thickness)	-	200	Bis sample 10% discount
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	7500	Bis sample 10% discount
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	200	Bis sample 10% discount
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	200	Bis sample 10% discount
5/5.5- Table1(REQUIREMENTS-Thickness)	-	200	Bis sample 10% discount
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	7500	Bis sample 10% discount
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	200	Bis sample 10% discount
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	200	Bis sample 10% discount
5/5.5- Table1(REQUIREMENTS-Thickness)	-	200	Bis sample 10% discount
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	7500	Bis sample 10% discount
8.3(Measurement of thickness)	-	200	Bis sample 10% discount
Cl.8.3(Measurement of thickness ")	-	200	Bis sample 10% discount
5.5 (Amendment 1)(Thickness)	-	200	Bis sample 10% discount
5.7 Table 2 i) (Amendment 1)(Relative Density)	-	300	Bis sample 10% discount
5.7, Table 2 ii) (Amendment 1)(Hardness, degree, Shore A)	-	400	Bis sample 10% discount
5.7, Table 2 iv) (Amendment 1)(Abrasion Resistance at applied force of 10 N)	-	800	Bis sample 10% discount
5.7, Table 2 v) (Amendment 1)(Tensile strength)	-	700	Bis sample 10% discount
5.7, Table 2 vi) (Amendment 1)(Elongation at break)	-	500	Bis sample 10% discount
5.7, Table 2 vii) (Amendment 1)(Tear strength (average force))	-	600	Bis sample 10% discount
5.7, Table 2 iii) (Amendment 1)(Flexing resistance)	-	800	Bis sample 10% discount
5/5.1(REQUIREMENTS-General)	-	0	NA
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	0	NA
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	0	NA
5/5.1(REQUIREMENTS-General)	-	0	NA
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	0	NA
5/5.1(REQUIREMENTS-General)	-	0	NA
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	0	NA
6(Marking and packing)	-	0	NA
8.1(Test methods)	-	0	NA
Cl.6.1,6.2,6.3(Marking and packing)	-	0	NA
8.1(Test Methods)	-	0	NA

15 May, 2027

-
-

106

IS 10702 (2023)

Hawai Chappal-Specification

HAWAI CHAPPAL - SPECIFICATION

34481 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.2(Length)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.3(Thickness)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No. 1 , i)(Density)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No. 1 , iii)(3Split tear strength)	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	800	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	800	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	2400	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	300	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 2 , iv)(Stud bolt)	-	300	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	700	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	28000	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl.No. 5.2(lead content)	-	1000	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.3(Thickness)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.4 , Table No . 2 , iv)(Stud bolt)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	4500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	1000	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	2400	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	1000	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	4500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	2400	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	300	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	2800	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.1 - 4.1.1(Bottom Material)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.1 - 4.1.2(Strap Material)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.1 - 4.1.3(Material)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.1 - 4.1.4(Material)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.2(Material)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.3 - 4.3.1(Thickness)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.3 - 4.3.2(Thickness)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	800	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	4500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	700	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	2800	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
6(MARKING AND PACKING)	-	200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	1200	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	300	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	300	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	300	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	300	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	500	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
6(MARKING AND PACKING)	-	100	15% Discount on BIS samples & 10% on CLE, AFMEC & FAFM Samples.
4.1(Material)	-	0	-
4.2(Length)	-	0	-
4.3(Thickness)	-	0	-
4.4 , Table No. 1 , i)(Density)	-	0	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	0	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	0	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	0	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	0	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	0	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	0	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	0	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	0	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	0	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	0	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	0	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	0	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
Cl.No. 5.2(lead content)	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	0	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	0	-
Clause 4.1 - 4.1.1(Bottom Material)	-	0	-
Clause 4.1 - 4.1.2(Strap Material)	-	0	-
Clause 4.1 - 4.1.3(Material)	-	0	-
Clause 4.1 - 4.1.4(Material)	-	0	-
Clause 4.2(Material)	-	0	-
Clause 4.3 - 4.3.1(Thickness)	-	0	-
Clause 4.3 - 4.3.2(Thickness)	-	0	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	0	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	0	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	0	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	0	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	0	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	0	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	0	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	0	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	0	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	0	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	0	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	0	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	0	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	0	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	0	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	0	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	0	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	0	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	0	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	0	-
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	0	-
6(MARKING AND PACKING)	-	0	-
4.1(Material)	-	-	-
4.2(Length)	-	-	-
4.3(Thickness)	-	-	-
4.4 , Table No. 1 , i)(Density)	-	-	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	-	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	-	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	-	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	-	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	-	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	-	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	-	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	-	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	-	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	-	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	-	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	-	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	-	-
Cl.No. 5.2(lead content)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	-	-
Cl. No.5.1,Table no.1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	-	-
Clause 4.1 - 4.1.1(Bottom Material)	-	-	-
Clause 4.1 - 4.1.2(Strap Material)	-	-	-
Clause 4.1 - 4.1.3(Material)	-	-	-
Clause 4.1 - 4.1.4(Material)	-	-	-
Clause 4.2(Material)	-	-	-
Clause 4.3 - 4.3.1(Thickness)	-	-	-
Clause 4.3 - 4.3.2(Thickness)	-	-	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	-	-
Clause 4.4 Table 1 -iii)(Split tear strength, kg, Min)	-	-	-
Clause 4.4 Table 1 -iv) - a("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, percent, Max")	-	-	-
Clause 4.4 Table 1 -iv) - b(Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber, percent, Max)	-	-	-
Clause 4.4 Table 1 -v)(Abrasion resistance at applied force 5 N)	-	-	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	-	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	-	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	-	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	-	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	-	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	-	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	-	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	-	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	-	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	-	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	-	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	-	-
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	-	-
6(MARKING AND PACKING)	-	-	-

15 May, 2027

-
Included w.e.f. 05.03.2024 Amendment No.1 Included w.e.f. 01.05.2024

107

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

SPECIFICATION FOR SANDAL AND SLIPPERS

42500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SHAPE AND DESIGN)	-	100	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.5("SIZE AND FITTINGS ")	-	100	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.6("CONSTRUCTION ")	-	100	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.7(MATERIAL)	-	100	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	1200	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4,Table no. 4(ii)(Density)	-	200	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4,Table no. 5(i)(Density)	-	200	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	700	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	600	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	2400	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	700	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	1800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	28000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.2(Lead content)	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	700	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	700	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	600	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	700	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	4500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	1200	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	2400	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	1000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	4500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	2400	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	300	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	2800	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1500	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	26000	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.9.(MARKING AND PACKING)	-	100	15% Discount on BIS Samples & 10% Discount on CLE, AFMEC & FAFM Samples.
Cl. No.4(SHAPE AND DESIGN)	-	0	-
Cl. No.5("SIZE AND FITTINGS ")	-	0	-
Cl. No.6("CONSTRUCTION ")	-	0	-
Cl. No.7(MATERIAL)	-	0	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	0	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	0	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	0	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	0	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	0	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	0	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	0	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	0	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	0	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	0	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	0	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	0	-
Cl. No.8.4,Table no. 5(i)(Density)	-	0	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	0	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	0	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	0	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	0	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	0	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	0	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	0	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	0	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	0	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	0	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	0	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	0	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
Cl. No.8.6.2(Lead content)	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	0	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	0	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	0	-
Cl. No.9.(MARKING AND PACKING)	-	0	-
Cl. No.4(SHAPE AND DESIGN)	-	-	-
Cl. No.5("SIZE AND FITTINGS ")	-	-	-
Cl. No.6("CONSTRUCTION ")	-	-	-
Cl. No.7(MATERIAL)	-	-	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	-	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	-	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	-	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	-	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	-	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	-	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	-	-
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	-	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	-	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	-	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	-	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	-	-
Cl. No.8.4,Table no. 5(i)(Density)	-	-	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	-	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	-	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	-	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	-	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	-	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	-	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	-	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	-	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	-	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	-	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	-	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	-	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	-	-
Cl. No.8.6.2(Lead content)	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	-	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	-	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	-	-
Cl. No.9.(MARKING AND PACKING)	-	-	-

15 May, 2027

-
Included w.e.f. 05.03.2024 Amendment No.1 Included w.e.f. 01.05.2024

108

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

62500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(DESIGN)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
6(SIZE AND FITTINGS)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.1(Whole Footwear)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.5(Energy Absorption at Seat Region)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.6(Complete Shoe Flexing)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.7(Washability)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.8(Slip Resistance)	-	1800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.9(Heel Drop)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , i)(Flexing resistance)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , ii)(Tear strength (average force))	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , iii)("Colour fastness rubbing (To and fro) Grey scale rate Dry: (rubbing) Rating: (Marring and staining) ")	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , iv) ,b)(Water vapour coefficient)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , v)(Stitch tear strength (double hole))	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Rating: (Marring)")	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , vii)(Tensile strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , viii)(Elongation at break,)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , i)(Breaking strength "As per Method 1 of IS 7016 (Part 2)/ ISO 1421 : 2016 or ISO 17706")	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , ii)(Elongation at break)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , vii)(Hydrolysis resistance)	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , viii)(Colour fastness to light grey scale rate)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , ix)(Bursting Strength,)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , i)(Tear strength,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, ")	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, ")	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , v) , a)(Water vapour permeability,)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , v) , b)("Water vapour coefficient, " As per IS 15298 (Part 1))	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , i)(Thickness)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , ii)(Flexing index)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , i)(Thickness)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , iii) , b)(Water Desorption)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , i)(Abrasion resistance (volume loss))	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , ii)(Flexing resistance)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , iv)(Tear strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , v)(Tensile strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , vi)(Elongation at break)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , vii)(Compression set)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.7 , Table No. 8 , i)(Compression set)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.7 , Table No. 8 , ii)(Split tear strength,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.7 , Table No. 8 , iii)(Heat shrinkage,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.7 , Table No. 8 , iv)(Elongation at break,)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	250	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , ii)(Resilience)	-	250	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , iii)(Moisture resistance)	-	250	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	250	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , iv) , b)(Area shape retention after 10th collapse, dry)	-	250	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , v)(Peel strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.9 , Table No. 10 , i)(Peel strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.9 , Table No. 10 , ii)(Shear strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.10 , Table No. 11 , ii)(Needle strength,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.11 , Table No. 12 , i)(Breaking strength of lace,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.11 , Table No. 12 , ii)(Lace tag strength,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.11 , Table No. 12 , v)(Strength of Buckle/Ski hook)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.11 , Table No. 12 , vi)(Corrosion resistance)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12("Chemical Requirement on Complete Product for All Types of Sports Shoe")	-	26000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.1(Whole Footwear)	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.5(Energy Absorption at Seat Region)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.6(Complete Shoe Flexing)	-	1150	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.7(Washability)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.1.9(Heel Drop)	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , i)(Flexing resistance)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , iv) ,b)(Water vapour coefficient)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Rating: (Marring)")	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , viii)(Elongation at break,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , ii)(Elongation at break)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , vii)(Hydrolysis resistance)	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , viii)(Colour fastness to light grey scale rate)	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.2 , Table No. 3 , ix)(Bursting Strength,)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , v) , a)(Water vapour permeability,)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.3 , Table No. 4 , v) , b)("Water vapour coefficient, " As per IS 15298 (Part 1))	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , i)(Thickness)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , ii)(Flexing index)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , i)(Thickness)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , iii) , b)(Water Desorption)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , ii)(Flexing resistance)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , vi)(Elongation at break)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.6 , Table No. 7 , vii)(Compression set)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.7 , Table No. 8 , i)(Compression set)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.7 , Table No. 8 , iv)(Elongation at break,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , ii)(Resilience)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , iii)(Moisture resistance)	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.8 , Table No. 9 , iv) , b)(Area shape retention after 10th collapse, dry)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.9 , Table No. 10 , ii)(Shear strength)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.10 , Table No. 11 , ii)(Needle strength,)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	4500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	1200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	4500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(x)(pH)	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
4(SAMPLING AND CONDITIONING)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
7.12, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	2800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
8(MARKING AND PACKING)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC & FAFM samples
5(DESIGN)	-	0	-
6(SIZE AND FITTINGS)	-	0	-
7.1.1(Whole Footwear)	-	0	-
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	0	-
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	0	-
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	0	-
7.1.5(Energy Absorption at Seat Region)	-	0	-
7.1.6(Complete Shoe Flexing)	-	0	-
7.1.7(Washability)	-	0	-
7.1.8(Slip Resistance)	-	0	-
7.1.9(Heel Drop)	-	0	-
7.2 , Table No. 2 , i)(Flexing resistance)	-	0	-
7.2 , Table No. 2 , ii)(Tear strength (average force))	-	0	-
7.2 , Table No. 2 , iii)("Colour fastness rubbing (To and fro) Grey scale rate Dry: (rubbing) Rating: (Marring and staining) ")	-	0	-
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	0	-
7.2 , Table No. 2 , iv) ,b)(Water vapour coefficient)	-	0	-
7.2 , Table No. 2 , v)(Stitch tear strength (double hole))	-	0	-
7.2 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Rating: (Marring)")	-	0	-
7.2 , Table No. 2 , vii)(Tensile strength)	-	0	-
7.2 , Table No. 2 , viii)(Elongation at break,)	-	0	-
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	0	-
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	0	-
7.2 , Table No. 3 , i)(Breaking strength "As per Method 1 of IS 7016 (Part 2)/ ISO 1421 : 2016 or ISO 17706")	-	0	-
7.2 , Table No. 3 , ii)(Elongation at break)	-	0	-
7.2 , Table No. 3 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	0	-
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	0	-
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	0	-
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	0	-
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	0	-
7.2 , Table No. 3 , vii)(Hydrolysis resistance)	-	0	-
7.2 , Table No. 3 , viii)(Colour fastness to light grey scale rate)	-	0	-
7.2 , Table No. 3 , ix)(Bursting Strength,)	-	0	-
7.3 , Table No. 4 , i)(Tear strength,)	-	0	-
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	0	-
7.3 , Table No. 4 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, ")	-	0	-
7.3 , Table No. 4 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, ")	-	0	-
7.3 , Table No. 4 , v) , a)(Water vapour permeability,)	-	0	-
7.3 , Table No. 4 , v) , b)("Water vapour coefficient, " As per IS 15298 (Part 1))	-	0	-
7.4 , Table No. 5 , i)(Thickness)	-	0	-
7.4 , Table No. 5 , ii)(Flexing index)	-	0	-
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	0	-
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	0	-
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	0	-
7.5 , Table No. 6 , i)(Thickness)	-	0	-
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	0	-
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	0	-
7.5 , Table No. 6 , iii) , b)(Water Desorption)	-	0	-
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	0	-
7.6 , Table No. 7 , i)(Abrasion resistance (volume loss))	-	0	-
7.6 , Table No. 7 , ii)(Flexing resistance)	-	0	-
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	0	-
7.6 , Table No. 7 , iv)(Tear strength)	-	0	-
7.6 , Table No. 7 , v)(Tensile strength)	-	0	-
7.6 , Table No. 7 , vi)(Elongation at break)	-	0	-
7.6 , Table No. 7 , vii)(Compression set)	-	0	-
7.7 , Table No. 8 , i)(Compression set)	-	0	-
7.7 , Table No. 8 , ii)(Split tear strength,)	-	0	-
7.7 , Table No. 8 , iii)(Heat shrinkage,)	-	0	-
7.7 , Table No. 8 , iv)(Elongation at break,)	-	0	-
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	0	-
7.8 , Table No. 9 , ii)(Resilience)	-	0	-
7.8 , Table No. 9 , iii)(Moisture resistance)	-	0	-
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	0	-
7.8 , Table No. 9 , iv) , b)(Area shape retention after 10th collapse, dry)	-	0	-
7.8 , Table No. 9 , v)(Peel strength)	-	0	-
7.9 , Table No. 10 , i)(Peel strength)	-	0	-
7.9 , Table No. 10 , ii)(Shear strength)	-	0	-
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	0	-
7.10 , Table No. 11 , ii)(Needle strength,)	-	0	-
7.11 , Table No. 12 , i)(Breaking strength of lace,)	-	0	-
7.11 , Table No. 12 , ii)(Lace tag strength,)	-	0	-
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	0	-
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	0	-
7.11 , Table No. 12 , v)(Strength of Buckle/Ski hook)	-	0	-
7.11 , Table No. 12 , vi)(Corrosion resistance)	-	0	-
7.12, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
7.12, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
7.12, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
7.12, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	0	-
7.12, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	0	-
7.12, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
7.12, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	0	-
7.12, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	0	-
7.12, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
7.12, Table no. 1 of IS 17011,(x)(pH)	-	0	-
7.12, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	0	-
4(SAMPLING AND CONDITIONING)	-	0	-
7.12, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	0	-
7.12("Chemical Requirement on Complete Product for All Types of Sports Shoe")	-	0	-
8(MARKING AND PACKING)	-	0	-

15 May, 2027

-
Included w.e.f. 05.03.2024

109

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

SPORTS FOOTWEAR PART -1 GENERAL PURPOSE

58000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl No.4.2(Construction)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.1(Insole)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.2(Toe spring height)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.6(Energy Absorption at Seat Region)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.7(Complete Shoe Flexing)	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.8(Washability)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.9(Slip Resistance)	-	1800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Min Rating: (Marring)")	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14("Chemical Requirement on Complete Product for all Types of Sports Shoe")	-	28000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.1(Insole)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.2(Toe spring height)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.6(Energy Absorption at Seat Region)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
4.3.8(Washability)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Min Rating: (Marring)")	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	4500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	1200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(vii)(Formaldehyde)	-	1000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(viii)(Organotin compounds)	-	4500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	300	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	2800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14, Table no. 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	1500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.1(Sampling and Conditioning)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.3(Whole Footwear)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 4.14("Chemical Requirement on Complete Product for all Types of Sports Shoe")	-	26000	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No . 5(MARKING AND PACKING)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.2 - 4.2.1(Construction)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.2 - 4.2.2(Construction)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.3 - 4.3.1(Whole Footwear)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.3 - 4.3.2(Whole Footwear)	-	100	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	600	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.4, Table 1 ii)(Tear strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.4, Table 2 i)(Breaking Strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.4, Table 2 ii)(Elongation at break)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.4, Table 2 iii)(Tear strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.5, Table 3 i)(Tear strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.6, Table 4 i)(Thickness)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.7, Table 5 i)(Thickness)	-	200	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	800	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	700	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	2400	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.9, Table 7 ii)(Split Tear strength)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	500	15% Discount on BIS samples & 10% Discount on CLE, AFMEC, FAFM.
Cl No.4.2(Construction)	-	-	-
4.3.1(Insole)	-	-	-
4.3.2(Toe spring height)	-	-	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	-	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	-	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	-	-
4.3.6(Energy Absorption at Seat Region)	-	-	-
4.3.7(Complete Shoe Flexing)	-	-	-
4.3.8(Washability)	-	-	-
4.3.9(Slip Resistance)	-	-	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	-	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	-	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	-	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	-	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	-	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	-	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	-	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	-	-
Cl No.4.4 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Min Rating: (Marring)")	-	-	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	-	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	-	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	-	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	-	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	-	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	-	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	-	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	-	-
Cl No.4.4 , Table No. 2 , vii)(Bursting Strength, kg/cm2 , Min)	-	-	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	-	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	-	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	-	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	-	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	-	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	-	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	-	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	-	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	-	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	-	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	-	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	-	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	-	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	-	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	-	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	-	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	-	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	-	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	-	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	-	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	-	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	-	-
Cl No.4.10 , Table No. 8 , iii)(Moisture resistance, percent, Min)	-	-	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	-	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	-	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	-	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	-	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	-	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	-	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	-	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	-	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	-	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	-	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(vii)(Formaldehyde)	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(viii)(Organotin compounds)	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	-	-
Cl No . 4.14, Table no. 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	-	-
Cl No.4.1(Sampling and Conditioning)	-	-	-
Cl No.4.3(Whole Footwear)	-	-	-
Cl No . 4.14("Chemical Requirement on Complete Product for all Types of Sports Shoe")	-	-	-
Cl No . 5(MARKING AND PACKING)	-	-	-
Clause 4.2 - 4.2.1(Construction)	-	-	-
Clause 4.2 - 4.2.2(Construction)	-	-	-
Clause 4.3 - 4.3.1(Whole Footwear)	-	-	-
Clause 4.3 - 4.3.2(Whole Footwear)	-	-	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	-	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	-	-
Clause 4.3 - 4.3.5(Out Sole to Mid Sole (Multilayer) Bond)	-	-	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	-	-
Clause 4.4, Table 1 ii)(Tear strength)	-	-	-
Clause 4.4, Table 1 iv)-a(Water Vapour Permeability)	-	-	-
Clause 4.4, Table 2 v)-b(Water Vapour Coeffecient)	-	-	-
Clause 4.4, Table 1 v)(Stitch Tear Strength(Double Hole))	-	-	-
Clause 4.4, Table 2 i)(Breaking Strength)	-	-	-
Clause 4.4, Table 2 ii)(Elongation at break)	-	-	-
Clause 4.4, Table 2 iii)(Tear strength)	-	-	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	-	-
Clause 4.5, Table 3 i)(Tear strength)	-	-	-
Clause 4.5, Table 3 ii)(Abrasion Resistance)	-	-	-
Clause 4.5, Table 3 v)-a(Water Vapour Permeability)	-	-	-
Clause 4.5, Table 3 v)-b(Water Vapour Coeffecient)	-	-	-
Clause 4.6, Table 4 i)(Thickness)	-	-	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	-	-
Clause 4.6, Table 4 iv)-a(Water Absorption)	-	-	-
Clause 4.6, Table 4 iv)-b(Water Desorption)	-	-	-
Clause 4.7, Table 5 i)(Thickness)	-	-	-
Clause 4.7, Table 5 ii)(Abrasion Resistance)	-	-	-
Clause 4.7, Table 5 iii)-a(Water Absorption)	-	-	-
Clause 4.7, Table 5 iii)-b(Water Desorption)	-	-	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	-	-
Clause 4.8, Table 6 ii)(Flexing Resistance)	-	-	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	-	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	-	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	-	-

15 May, 2027

-
Included w.e.f. 05.03.2024 Amendment No.1 Included w.e.f. 01.05.2024

110

IS 2080 (2021)

Specification for stabilized hydrogen peroxide First Revision

Industrial chemical

10000 View breakup
-

Clause No.	Exclusion	Remark
5.1(Packing)	-	NA
5.2(Marking)	-	NA
Annex C(Stability)	-	NA
4.1(Description - IS 2080:2021)	-	NA
4.2(Strength - IS 2080:2021)	-	NA
4.3(Stability - IS 2080:2021)	-	NA
4.4/Table 1 (i)(Acidity (as H2SO4) - IS 2080:2021)	-	NA
4.4/Table 1 (ii)(Residue on Evaporation - IS 2080:2021)	-	NA
4.4/Table 1 (iii)(Residue on Ignition - IS 2080:2021)	-	NA
4.4/Table 1 (iv)(Iron (as Fe) - IS 2080:2021)	-	NA
4.4/Table 1 (v)(Copper (as Cu) - IS 2080:2021)	-	NA
4.4/Table 1 (vi)(Lead (as Pb) - IS 2080:2021)	-	NA
4.4/Table 1 (vii)(Arsenic (as As2O3) - IS 2080:2021)	-	NA

15 May, 2027

-
Included w.e.f. 04.03.2024

111

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.5 and Table 1 i(Capacity)	-	250	10% Discount on BIS sample.
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	10% Discount on BIS sample.
5.2 and Table 1 iii(Ends per dm )	-	250	10% Discount on BIS sample.
5.2 and Table 1 iv(Picks per dm )	-	250	10% Discount on BIS sample.
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	250	10% Discount on BIS sample.
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	420	10% Discount on BIS sample.
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	420	10% Discount on BIS sample.
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	7500	10% Discount on BIS sample.
5.2 and Table 1 x(Ash content )	-	900	10% Discount on BIS sample.
4.2(Tapes – Width IS 6192 and IS 11197)	-	200	10% Discount on BIS sample.
4.2(Tapes – Linear Density )	-	300	10% Discount on BIS sample.
4.2(Construction)	-	200	10% Discount on BIS sample.
4.3(Sacks)	-	300	10% Discount on BIS sample.
4.3.1(Bottom Seam)	-	600	10% Discount on BIS sample.
4.3.1(The two rows of stitches shall be separated from each other)	-	200	10% Discount on BIS sample.
4.3.1( The outer stitch)	-	200	10% Discount on BIS sample.
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	200	10% Discount on BIS sample.
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	200	10% Discount on BIS sample.
4.3.1(stitches/dm)	-	300	10% Discount on BIS sample.
4.3.2(Mouth)	-	200	10% Discount on BIS sample.
4.4(Mass of the loose liner )	-	300	10% Discount on BIS sample.
4.4(Width of the loose liner)	-	200	10% Discount on BIS sample.
4.4(Length of the line)	-	200	10% Discount on BIS sample.
4.4(Bottom seam of the loose liner)	-	600	10% Discount on BIS sample.
4.4.1(Liner)	-	200	10% Discount on BIS sample.
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	300	10% Discount on BIS sample.
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	600	10% Discount on BIS sample.
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	600	10% Discount on BIS sample.

15 May, 2027

-
-

112

IS 3617 (1992)

Textiles – Gent’s pullover, knitted – Specification (first revision)

5160 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1( Dimensional changes)	-	420	EXCLUDING 18 % GST
5.2(Contruction )	-	120	EXCLUDING 18 % GST
5.2(Dimensional Changes )	-	420	EXCLUDING 18 % GST
5.2(Scouring Loss )	-	550	EXCLUDING 18 % GST
5.2(Alkali Solubility )	-	550	EXCLUDING 18 % GST
5.2(Colorfastness to light )	-	900	EXCLUDING 18 % GST
5.2(Colorfastness to Washing )	-	650	EXCLUDING 18 % GST
5.2(Colorfastness to Rubbing)	-	450	EXCLUDING 18 % GST
5.2(Colorfastness to dry cleaning)	-	450	EXCLUDING 18 % GST
5.2(Fiber content )	-	1050	EXCLUDING 18 % GST

15 May, 2027

-
-

113

IS 13995 (1995)

Unlined moulded rubber boots - Specification

5400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Thickness )	-	120	10% Discount on BIS sample.
5.1.1(Tensile Strength (before ageing))	-	420	10% Discount on BIS sample.
5.1.2(Tensile Strength (after ageing))	-	4200	10% Discount on BIS sample.
5.1.3(Tear Strength)	-	420	10% Discount on BIS sample.
5.1.4(Resistance to dry heat ageing )	-	550	10% Discount on BIS sample.
5.1.5(Flexing resistance of upper)	-	600	10% Discount on BIS sample.
5.1.6(Design)	-	120	10% Discount on BIS sample.
5.1.7(Size)	-	120	10% Discount on BIS sample.

15 May, 2027

-
-

114

IS 11544 (1986)

Specification for slipper, rubber

3220 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Shape & Design)	-	120	EXCLUDING 18 % GST
3.2(Relative density )	-	400	EXCLUDING 18 % GST
3.2(Hardness (IRHD))	-	500	EXCLUDING 18 % GST
3.2(Hardness after ageing)	-	550	EXCLUDING 18 % GST
3.2(Flexural endurance)	-	800	EXCLUDING 18 % GST
3.2.4(Mass per unit area)	-	150	EXCLUDING 18 % GST
3.2.4(End per cm)	-	150	EXCLUDING 18 % GST
3.2.4(Picks per cm)	-	150	EXCLUDING 18 % GST
3.2.4(Colour fasntess to washing)	-	400	EXCLUDING 18 % GST
3.2.5(Type of Thread)	-	120	EXCLUDING 18 % GST
3.2.6(Thickness of components)	-	400	EXCLUDING 18 % GST

15 May, 2027

-
-

115

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

6950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Size & Thickness )	-	350	10% Discount on BIS Sample.
4.2(Hardness (Shore A))	-	350	10% Discount on BIS Sample.
4.2(Compression set)	-	300	10% Discount on BIS Sample.
4.2(Split tear strength)	-	420	10% Discount on BIS Sample.
4.2(Shrinkage at room temp)	-	4200	10% Discount on BIS Sample.
4.2(Heat Shrinkage )	-	550	10% Discount on BIS Sample.
4.2(Water absorption)	-	300	10% Discount on BIS Sample.
4.2(Flexing resistance )	-	1100	10% Discount on BIS Sample.

15 May, 2027

-
-

116

IS 297 (2001)

Sodium sulphide, technical - Specification (Second Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2 (i)(Total Sulphide ( as Na2S))	-	1250	EXCLUDING 18 % GST
3.2 (ii)(Sodium )	-	1250	-
3.2 (iii)(Excess Alkali (as Na2CO3))	-	1250	EXCLUDING 18 % GST
3.2 (vi)(Reducing)	-	1250	EXCLUDING 18 % GST
3.2 (v)(Iron and aluminum compound (Fe2O3))	-	1250	EXCLUDING 18 % GST
3.2 (vi)(Sodium Sulphate (Na2SO4))	-	1250	EXCLUDING 18 % GST
3.2 (vii)(Sodium Chloride ( as NaCI))	-	1250	EXCLUDING 18 % GST
3.2 (viii)(Water insoluble)	-	1250	EXCLUDING 18 % GST

15 May, 2027

-
-

117

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

20695 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	420	10% Discount on BIS Sample.
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	720	10% Discount on BIS Sample.
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	660	10% Discount on BIS Sample.
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	2940	10% Discount on BIS Sample.
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	120	10% Discount on BIS Sample.
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	2490	10% Discount on BIS Sample.
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	2710	10% Discount on BIS Sample.
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	3095	10% Discount on BIS Sample.
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	3500	10% Discount on BIS Sample.
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	1000	10% Discount on BIS Sample.
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	120	10% Discount on BIS Sample.
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	120	10% Discount on BIS Sample.
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	120	10% Discount on BIS Sample.
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	720	10% Discount on BIS Sample.
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	720	10% Discount on BIS Sample.

15 May, 2027

-
-

118

IS 4505 (2015)

Sodium formaldehyde sulphoxylate - Specification (First Revision)

13215 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl no 4.3 [ Table 1, Sl no.(i) ] Annex A-2 Grade-1(Sodium formaldehyde sulphoxylate dihydrate (NaHSO2.CH2O.2H2O))	-	2000	10% Discount on BIS Sample.
Cl no 4.3 [ Table 1, Sl no.(i) ] Annex A-2 Grade-2(Sodium formaldehyde sulphoxylate dihydrate (NaHSO2.CH2O.2H2O))	-	2000	10% Discount on BIS Sample.
Cl no 4.3 [ Table 1, Sl no.(iii) ] Annex A-2 Grade-1 & Grade 2(Sodium sulphite (Na2SO3))	-	2000	10% Discount on BIS Sample.
Cl no 4.3 [ Table 1, Sl no.(iv) ] Annex A-3 Grade-1 & Grade 2(pH (of 1 percent solution))	-	500	10% Discount on BIS Sample.
Cl no 4.3 [ Table 1, Sl no.(v) ] Annex A-4 Grade-1 (Iron (as Fe))	-	1500	10% Discount on BIS Sample.
Cl no 4.3 [ Table 1, Sl no.(vi) ] Ref to IS 12074 Grade-1 & Grade 2(Lead (as Pb))	-	1500	10% Discount on BIS Sample.
Cl no 4.3 [ Table 1, Sl no.(vii) ] Annex A-5 Grade-1 & Grade 2(Copper (as Cu))	-	1500	10% Discount on BIS Sample.
Cl no 4.3 [ Table 1, Sl no.(viii) ] Annex A-6 Grade-1 (Zinc (as Zn))	-	1500	10% Discount on BIS Sample.

15 May, 2027

-
-

119

IS 11226 (1993)

Leather safety footwear having direct moulded rubber sole specification (First Revision)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.11(Materials)	-	4080	10% Discount on BIS Sample.
5.2.11.2(Materials)	-	3910	10% Discount on BIS Sample.
5.3(Components)	-	2620	10% Discount on BIS Sample.
5.4( Manufacture )	-	3910	10% Discount on BIS Sample.
5.4.8(Workmanship and Finish)	-	1930	10% Discount on BIS Sample.
5.5(Mass)	-	420	10% Discount on BIS Sample.
5.6(Performance Test)	-	1500	10% Discount on BIS Sample.
5.7(Adhesion Test on Moulded Bottoms)	-	350	10% Discount on BIS Sample.

15 May, 2027

-
-

120

IS 12254 (1993)

Polyvinyl chloride (PVC) Industrial boots - Specification (First Revision)

8800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Shape and Dimension)	-	120	EXCLUDING 18 % GST
5.2(Shape and Dimension)	-	120	EXCLUDING 18 % GST
5.3.1(Thickness)	-	550	EXCLUDING 18 % GST
5.4 Table 2(Hardness, IS 12240 (Part 2))	-	700	EXCLUDING 18 % GST
5.5(Relative Density, IS 12240 (Part 3))	-	350	-
5.6(Volatility, IS 12240 ( Part 2) )	-	550	EXCLUDING 18 % GST
5.7(Lead Content )	-	550	EXCLUDING 18 % GST
5.8 Table 3(Tensile Requirements, Upper, IS 12240 ( Part 6) )	-	840	EXCLUDING 18 % GST
5.9(Resistance to Cut Growth (Flexing test) for Sole, IS 12240 (Part 7))	-	600	EXCLUDING 18 % GST
5.1(Resistance to Flexing for Upper, IS 12240 (Part 8))	-	600	EXCLUDING 18 % GST
5.11(Leg Height, IS 12240 (part 9))	-	120	EXCLUDING 18 % GST
5.12(Leakage Resistance)	-	1100	EXCLUDING 18 % GST
5.13(Cold Flex Temperature)	-	1500	EXCLUDING 18 % GST
5.15(Performance)	-	1100	EXCLUDING 18 % GST

15 May, 2027

-
Included w.e.f. 31.07.2024 Exclusion: Cl.5.5.5 (Upper Cold Flex Resistance)

Bureau of Indian Standards

The National Standards Body of India

Sleen India Biz venture Private Limited, Agra

RAHANKALAN ROAD, PART 295, BLOCK-A KUBERPUR, 300 METER FROM RAILWAY CROSSING CHALESHAR ROAD, Agra, Uttar Pradesh, India, 282006, Agra, Agra, Uttar Pradesh, 282006

8193022228 sleen.info@gmail.com

Scope List