BIS - LIMS (Laboratory Information Management System)

Central Institute of Petrochemicals Engineering & Technology (CIPET), CSTS - Dehradun

CIPET : Centre for Skilling and Technical Support (CSTS), Haridwar Road, Post-Bhaniyawala, Doiwala, Dehradun, Dehradun, Dehradun, Uttarakhand, 248140

7457001351 testing.cipetdehradun@gmail.com

Scope List

Reset

73 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 16190 (2014)

Agro textiles - High density polyethylene (HDPE) laminated woven lay flat tube for irrigation purpose - Specification

67548 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4,4.1 IS 6192( MATERIALS HDPE Tapes)	-	4750.00	1. MATERIAL IDENTIFICATION - 2000.00 2. WIDTH OF TAPE - 250.00 3. LINEAR DENSITY - 500.00 4. PRESENCE OF UV STABLIZER - 2000.00
4.2 IS 6899(MATERIALS HDPE Fabric)	-	500.00	1. ENDS PER DM - 250.00 2. PICKS PER DM - 250.00
5,5.1(MANUFACTURE Lamination )	-	4000.00	1. PRESENCE OF UV STABLIZER - 2000.00 2. MATERIAL IDENTIFICATION - 2000.00
5,5.2(MANUFACTURE A 5 layer laminated fabric is produced using acombination of 2 layers of HDPE fabric and 3 layersof coating film. The minimum coating thickness shall be 35 µ. The layers of HDPE fabric used to manufacture lay flat tubes, shall be joined by sandwich lamination.The minimum thickness of the sandwich laminationshall be 40 µ. )	-	250.00	-
5,5.3 Table 1.(MANUFACTURE The laminated HDPE woven fabric is to be formed in to lay flat tube of the required inside diameter using a heat sealing process keeping the minimum overlap as specified in Table 1.)	-	250.00	-
6(REQUIREMENTS)	-	250.00	-
6. Table 2 ii) a) IS 1969 (Part 1) ( Breaking strength before UV exposure : Wrap)	-	2200.00	1. WARP WAY- 1100.00 & 250 SPECIMEN CHARGE. 2. WEFT WAY- 1100.00 & 250 SPECIMEN CHARGE.
6. Table 2 iv) b) Annex B(Retention of breaking strength after UV exposure of 500 h : weft 85 percent of original actual value (fabric))	-	2200.00	1. WARP WAY- 1100.00 & 250 SPECIMEN CHARGE. 2. WEFT WAY- 1100.00 & 250 SPECIMEN CHARGE.
6(REQUIREMENTS)	-	89000.00	UV EXPOSURE CHARGE- 89000.00
6. Table 2 v) IS 14714 (Abrasion resistance : Loss in breaking strength shall not be more than 15 percent)	-	1375.00	Test Charge- 875.00 SPECIMEN PREPARTION CHARGE- 500.00
6. Table 2 vi) a) IS 14293 ( Trapezoid tear strength: Wrap)	-	1350.00	Test Charge-1100.00 SPECIMEN PREPARTION CHARGE- 250.00
6. Table 2 vi) b) IS 14293 ( Trapezoid tear strength : Weft)	-	1350.00	Test Charge-1100.00 SPECIMEN PREPARTION CHARGE- 250.00
6. Table 2 vii) Annex C (Puncture strength)	-	1350.00	Test Charge-1100.00 SPECIMEN PREPARTION CHARGE- 250.00
6. Table 2 viii) Annex D ( Environmental stress cracking test : )	-	1200.00	-
6. Table 2 ix) a) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 15 percent Wrap)	-	1800.00	AGEING CHARGE-1800.00
6. Table 2 x) Annex E (Cold cracking resistance test at –5°C)	-	1100.00	-
6.1 Table 1(Internal Diameter : The inside diameter of the lay flat tube shall be as given in Table 1. The internal diameter of the lay flat tube shall be measured by a suitable conical plug gauge and shall conform to the tolerance specified in Table 1)	-	250.00	-
6.2(Workmanship)	-	300.00	-
6.3,6.3.1(Hydrostatic Burst Pressure Test)	-	1500.00	Test Charge-1000.00 SPECIMEN PREPARTION CHARGE- 500.00
6.4 , 6.4.1(Proof Pressure Tes)	-	1500.00	Test Charge-1000.00 SPECIMEN PREPARTION CHARGE- 500.00
6.5( Length : Unless specified otherwise, the standard length shall be 30 m. A tolerance of +5 percent shall be permitted on the length prescribed for the lay flat tube by the purchaser. No negative tolerance shall be permitted)	-	250.00	-
6.6(Kink Test :)	-	1100.00	-
6.7 IS 1969 (Part 1)(Welded Seam Strength Before UV Exposure : When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in IS 1969 (Part 1), welded seam strength before UV exposure shall be not less than the 80 percent of the original actual fabric strength)	-	1350.00	Test Charge- 1100.00 SPECIMEN PREPARTION CHARGE- 250.00
6.8 Annex B and IS 1969 (Part 1)(Welded Seam Strength After UV Exposure: When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in Annex B and IS 1969 (Part 1), the loss in welded seam strength after UV exposure shall be not more than 15 percent)	-	1100.00	-
6. Table 2 ix) b) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 1 5 percent Weft)	-	0.00	-
6. Table 2 iii) IS 1969 (Part 1) ( Elongation at break)	-	0.00	-
6.5( Length : Unless specified otherwise, the standard length shall be 30 m. A tolerance of +5 percent shall be permitted on the length prescribed for the lay flat tube by the purchaser. No negative tolerance shall be permitted)	-	0.00	-
5,5.3 Table 1.(MANUFACTURE The laminated HDPE woven fabric is to be formed in to lay flat tube of the required inside diameter using a heat sealing process keeping the minimum overlap as specified in Table 1.)	-	0.00	-
6. Table 2 vi) a) IS 14293 ( Trapezoid tear strength: Wrap)	-	0.00	-
6. Table 2 vi) b) IS 14293 ( Trapezoid tear strength : Weft)	-	0.00	-
6. Table 2 i) IS 1964 (Mass)	-	0.00	-
6. Table 2 ii) b) IS 1969 (Part 1) ( Breaking strength before UV exposure : Weft)	-	0.00	-
6. Table 2 iv) a) Annex B(Retention of breaking strength after UV exposure of 500 h : Wrap 85 percent of original actual value (fabric))	-	0.00	-
5,5.1(MANUFACTURE Lamination )	-	0.00	-
8(PACKING)	-	0.00	-
6. Table 2 v) IS 14714 (Abrasion resistance : Loss in breaking strength shall not be more than 15 percent)	-	0.00	-
6. Table 2 ix) a) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 15 percent Wrap)	-	0.00	-
6. Table 2 ix) b) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 1 5 percent Weft)	-	0.00	-
6. Table 2 iii) IS 1969 (Part 1) ( Elongation at break)	-	0.00	-
6. Table 2 i) IS 1964 (Mass)	-	0.00	-
6. Table 2 vii) Annex C (Puncture strength)	-	0.00	-
6. Table 2 iv) b) Annex B(Retention of breaking strength after UV exposure of 500 h : weft 85 percent of original actual value (fabric))	-	0.00	-
6. Table 2 ii) b) IS 1969 (Part 1) ( Breaking strength before UV exposure : Weft)	-	0.00	-
4,4.1 IS 6192( MATERIALS HDPE Tapes)	-	0.00	-
4.2 IS 6899(MATERIALS HDPE Fabric)	-	0.00	-
5,5.2(MANUFACTURE A 5 layer laminated fabric is produced using acombination of 2 layers of HDPE fabric and 3 layersof coating film. The minimum coating thickness shall be 35 µ. The layers of HDPE fabric used to manufacture lay flat tubes, shall be joined by sandwich lamination.The minimum thickness of the sandwich laminationshall be 40 µ. )	-	0.00	-
6. Table 2 viii) Annex D ( Environmental stress cracking test : )	-	0.00	-
6. Table 2 x) Annex E (Cold cracking resistance test at –5°C)	-	0.00	-
6.1 Table 1(Internal Diameter : The inside diameter of the lay flat tube shall be as given in Table 1. The internal diameter of the lay flat tube shall be measured by a suitable conical plug gauge and shall conform to the tolerance specified in Table 1)	-	0.00	-
6.2(Workmanship)	-	0.00	-
6.3,6.3.1(Hydrostatic Burst Pressure Test)	-	0.00	-
6.4 , 6.4.1(Proof Pressure Tes)	-	0.00	-
6.6(Kink Test :)	-	0.00	-
6.7 IS 1969 (Part 1)(Welded Seam Strength Before UV Exposure : When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in IS 1969 (Part 1), welded seam strength before UV exposure shall be not less than the 80 percent of the original actual fabric strength)	-	0.00	-
6.8 Annex B and IS 1969 (Part 1)(Welded Seam Strength After UV Exposure: When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in Annex B and IS 1969 (Part 1), the loss in welded seam strength after UV exposure shall be not more than 15 percent)	-	0.00	-
8(PACKING)	-	0.00	-
6. Table 2 v) IS 14714 (Abrasion resistance : Loss in breaking strength shall not be more than 15 percent)	-	0.00	-
6. Table 2 ix) a) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 15 percent Wrap)	-	0.00	-
6. Table 2 ix) b) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 1 5 percent Weft)	-	0.00	-
6. Table 2 iii) IS 1969 (Part 1) ( Elongation at break)	-	0.00	-
6.5( Length : Unless specified otherwise, the standard length shall be 30 m. A tolerance of +5 percent shall be permitted on the length prescribed for the lay flat tube by the purchaser. No negative tolerance shall be permitted)	-	0.00	-
5,5.3 Table 1.(MANUFACTURE The laminated HDPE woven fabric is to be formed in to lay flat tube of the required inside diameter using a heat sealing process keeping the minimum overlap as specified in Table 1.)	-	0.00	-
6. Table 2 vi) a) IS 14293 ( Trapezoid tear strength: Wrap)	-	0.00	-
6. Table 2 vi) b) IS 14293 ( Trapezoid tear strength : Weft)	-	0.00	-
6. Table 2 i) IS 1964 (Mass)	-	0.00	-
6. Table 2 vii) Annex C (Puncture strength)	-	0.00	-
6. Table 2 iv) b) Annex B(Retention of breaking strength after UV exposure of 500 h : weft 85 percent of original actual value (fabric))	-	0.00	-
6. Table 2 ii) b) IS 1969 (Part 1) ( Breaking strength before UV exposure : Weft)	-	0.00	-
6. Table 2 iv) a) Annex B(Retention of breaking strength after UV exposure of 500 h : Wrap 85 percent of original actual value (fabric))	-	0.00	-
6. Table 2 ii) a) IS 1969 (Part 1) ( Breaking strength before UV exposure : Wrap)	-	0.00	-
4,4.1 IS 6192( MATERIALS HDPE Tapes)	-	0.00	-
4.2 IS 6899(MATERIALS HDPE Fabric)	-	0.00	-
4.2 IS 6899(MATERIALS HDPE Fabric)	-	0.00	-
5,5.1(MANUFACTURE Lamination )	-	0.00	-
5,5.2(MANUFACTURE A 5 layer laminated fabric is produced using acombination of 2 layers of HDPE fabric and 3 layersof coating film. The minimum coating thickness shall be 35 µ. The layers of HDPE fabric used to manufacture lay flat tubes, shall be joined by sandwich lamination.The minimum thickness of the sandwich laminationshall be 40 µ. )	-	0.00	-
6(REQUIREMENTS)	-	0.00	-
6. Table 2 viii) Annex D ( Environmental stress cracking test : )	-	0.00	-
6. Table 2 x) Annex E (Cold cracking resistance test at –5°C)	-	0.00	-
6.1 Table 1(Internal Diameter : The inside diameter of the lay flat tube shall be as given in Table 1. The internal diameter of the lay flat tube shall be measured by a suitable conical plug gauge and shall conform to the tolerance specified in Table 1)	-	0.00	-
6.2(Workmanship)	-	0.00	-
6.3,6.3.1(Hydrostatic Burst Pressure Test)	-	0.00	-
6.4 , 6.4.1(Proof Pressure Tes)	-	0.00	-
6.6(Kink Test :)	-	0.00	-
6.7 IS 1969 (Part 1)(Welded Seam Strength Before UV Exposure : When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in IS 1969 (Part 1), welded seam strength before UV exposure shall be not less than the 80 percent of the original actual fabric strength)	-	0.00	-
6.8 Annex B and IS 1969 (Part 1)(Welded Seam Strength After UV Exposure: When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in Annex B and IS 1969 (Part 1), the loss in welded seam strength after UV exposure shall be not more than 15 percent)	-	0.00	-
8(PACKING)	-	0.00	-
6. Table 2 v) IS 14714 (Abrasion resistance : Loss in breaking strength shall not be more than 15 percent)	-	0.00	-
6. Table 2 ix) a) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 15 percent Wrap)	-	0.00	-
6. Table 2 ix) b) IS 7016(Part 8) (Oven method) (Accelerated ageing test for 72 h at 70 ± 1°C: Loss in breaking strength shall not be more than 1 5 percent Weft)	-	0.00	-
6. Table 2 iii) IS 1969 (Part 1) ( Elongation at break)	-	0.00	-
6.5( Length : Unless specified otherwise, the standard length shall be 30 m. A tolerance of +5 percent shall be permitted on the length prescribed for the lay flat tube by the purchaser. No negative tolerance shall be permitted)	-	0.00	-
5,5.3 Table 1.(MANUFACTURE The laminated HDPE woven fabric is to be formed in to lay flat tube of the required inside diameter using a heat sealing process keeping the minimum overlap as specified in Table 1.)	-	0.00	-
6. Table 2 vi) a) IS 14293 ( Trapezoid tear strength: Wrap)	-	0.00	-
6. Table 2 vi) b) IS 14293 ( Trapezoid tear strength : Weft)	-	0.00	-
6. Table 2 i) IS 1964 (Mass)	-	0.00	-
6. Table 2 vii) Annex C (Puncture strength)	-	0.00	-
6. Table 2 iv) b) Annex B(Retention of breaking strength after UV exposure of 500 h : weft 85 percent of original actual value (fabric))	-	0.00	-
6. Table 2 iv) a) Annex B(Retention of breaking strength after UV exposure of 500 h : Wrap 85 percent of original actual value (fabric))	-	0.00	-
6. Table 2 ii) a) IS 1969 (Part 1) ( Breaking strength before UV exposure : Wrap)	-	0.00	-
5,5.1(MANUFACTURE Lamination )	-	0.00	-
6. Table 2 viii) Annex D ( Environmental stress cracking test : )	-	0.00	-
6. Table 2 x) Annex E (Cold cracking resistance test at –5°C)	-	0.00	-
6.1 Table 1(Internal Diameter : The inside diameter of the lay flat tube shall be as given in Table 1. The internal diameter of the lay flat tube shall be measured by a suitable conical plug gauge and shall conform to the tolerance specified in Table 1)	-	0.00	-
6.2(Workmanship)	-	0.00	-
6.3,6.3.1(Hydrostatic Burst Pressure Test)	-	0.00	-
6.4 , 6.4.1(Proof Pressure Tes)	-	0.00	-
6.6(Kink Test :)	-	0.00	-
6.7 IS 1969 (Part 1)(Welded Seam Strength Before UV Exposure : When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in IS 1969 (Part 1), welded seam strength before UV exposure shall be not less than the 80 percent of the original actual fabric strength)	-	0.00	-
6.8 Annex B and IS 1969 (Part 1)(Welded Seam Strength After UV Exposure: When a sample of fabric with seam cut from the lay flat tube is tested for welded seam strength as per the method specified in Annex B and IS 1969 (Part 1), the loss in welded seam strength after UV exposure shall be not more than 15 percent)	-	0.00	-
8(PACKING)	-	0.00	-
6. Table 2 iv) a) Annex B(Retention of breaking strength after UV exposure of 500 h : Wrap 85 percent of original actual value (fabric))	-	0.00	-
6. Table 2 ii) a) IS 1969 (Part 1) ( Breaking strength before UV exposure : Wrap)	-	0.00	-
6. Table 2 ii) b) IS 1969 (Part 1) ( Breaking strength before UV exposure : Weft)	-	0.00	-
4,4.1 IS 6192( MATERIALS HDPE Tapes)	-	0.00	-
5,5.2(MANUFACTURE A 5 layer laminated fabric is produced using acombination of 2 layers of HDPE fabric and 3 layersof coating film. The minimum coating thickness shall be 35 µ. The layers of HDPE fabric used to manufacture lay flat tubes, shall be joined by sandwich lamination.The minimum thickness of the sandwich laminationshall be 40 µ. )	-	0.00	-
6(REQUIREMENTS)	-	0.00	-

Complete

IS 14611 (2016)

Multilayered cross laminated sheets/tarpaulins/covers/agricultural films - Specification (First Revision)

TYPE- XLN, LN, MN, HN, & XHN

41955.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1(Workmanship)	-	500.00	-
Cl. 6.2(Substance)	-	500.00	-
Cl. 6.3(Accelerated ageing test)	-	4200.00	AGEING CHARGE- 4200.00
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	2600.00	1. LONGITUDINAL DIRECTION - 1300.00 2. TRANSVERSE DIRECTION - 1300.00
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	2600.00	1. LONGITUDINAL DIRECTION - 1300.00 2. TRANSVERSE DIRECTION - 1300.00
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- LN light)	-	2600.00	1. LONGITUDINAL DIRECTION - 1300.00 2. TRANSVERSE DIRECTION - 1300.00
Table1 - v)(Dart Impact Strength)	-	850.00	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- XLN Extra light)	-	2600.00	1. LONGITUDINAL DIRECTION - 1300.00 2. TRANSVERSE DIRECTION - 1300.00
Cl. 6.4(water proofness test)	-	1000.00	-
Cl. 6.5(Strenght of joints/seams)	-	1100.00	-
Cl. 6.6(Flex test)	-	1500.00	-
Cl. 6.6(Flex test)	-	6000.00	TEST CHARGE-1500. AGEING TEST-4500.00
Cl. 6.7(Ease of in-situ Repair)	-	500.00	-
Cl. 7.1(Eyelets and rope lashing)	-	500.00	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- XHN Extra heavy)	-	2600.00	1. LONGITUDINAL DIRECTION - 1300.00 2. TRANSVERSE DIRECTION - 1300.00
5.1(Carbon Black Content)	-	925.00	-
5.2(Panel)	-	500.00	-
5.3(Ends & Sides dimensions)	-	500.00	-
5.4(Panel Length & width)	-	500.00	-
Cl. 6.4(water proofness test)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-XLN Extra light, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-LN Light, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-MN Medium, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-HN Heavy, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-XHN Extra heavy, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- HN heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- HN heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- XHN Extra Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.1(Workmanship)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2(Substance)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.3(Accelerated ageing test)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.5(Strenght of joints/seams)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.7(Ease of in-situ Repair)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 7.1(Eyelets and rope lashing)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-XLN Extra light, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-LN Light, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-MN Medium, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-HN Heavy, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. i(Mass per unit area, Grade-XHN Extra heavy, Ref. IS 7016(Part 1))	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (a)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (a)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- HN heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- LN light)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- HN heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XHN Extra heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- LN light)	-	0.00	-
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- MN Medium)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- HN Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- XHN Extra Heavy)	-	0.00	ALREADY TAKEN ABOVE.
Cl 4(Types)	-	0.00	ALREADY TAKEN ABOVE.
Cl 5(Construction)	-	0.00	ALREADY TAKEN ABOVE.
Cl 6.1(Workmanship)	-	0.00	ALREADY TAKEN ABOVE.
Cl 6.2 & Table1(Substance)	-	0.00	ALREADY TAKEN ABOVE.
Cl 6.3 & Table1(Accelerated Ageing Test)	-	0.00	ALREADY TAKEN ABOVE.
Cl 6.4(Water Proofness Test)	-	0.00	ALREADY TAKEN ABOVE.
Cl 6.5 & Annex C(Strength Of Joints/Seams)	-	0.00	ALREADY TAKEN ABOVE.
Cl 6.6(Flex Test)	-	0.00	ALREADY TAKEN ABOVE.
Cl 6.7 & Table1(Ease of in-situ Repair)	-	0.00	ALREADY TAKEN ABOVE.
Cl 7.1(Eyelets & Rope Lashing)	-	0.00	ALREADY TAKEN ABOVE.
Table1 - vi)(Average Tensile Strength & Elongation at Break after Exposing to UV Radiation & Weathering)	-	0.00	ALREADY TAKEN ABOVE.
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (a)(Tear strenght, Annex-F, Grade- XLN Extra light)	-	0.00	ALREADY TAKEN ABOVE.

Complete

IS 17216 (2019)

Polyethylene Mulch Films for Agriculture and Horticulture • Specification

22632 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Density)	-	500.00	-
5.1.2(Melt Flow Index)	-	1100.00	-
5.1.5(UV Stabilizer)	-	2500.00	-
5.2.1(Visual Appearance)	-	500.00	-
5.2.4(Odour)	-	500.00	-
5.3.1.1(Tolerance on thickness)	-	500.00	-
5.3.1.2(Tolerance on width)	-	500.00	-
5.3.2(Impact Strength)	-	1350.00	Test Charge-850.00 SPECIMEN PREPARATION CHARGE- 500.00
5.3.3(Tensile Strength at Break)	-	3100.00	Test Charge-2600.00 SPECIMEN PREPARATION CHARGE- 500.00
5.3.5(Coefficient of Friction)	-	850.00	-
5.3.6(Elmendorf Tear Strength)	-	2000.00	Test Charge-1500.00 SPECIMEN PREPARATION CHARGE- 500.00
5.3.7(Opacity)	-	700.00	-
5.4, Table 2(Carbon black, percent)	-	925.00	-
5.4, Table 2(Carbon black dispersion)	-	700.00	-
5.4, Table 2(Ash content, percent)	-	1200.00	-
5.5(Service Life)	-	601840.00	UV EXPOSURE CHARGE- 458 HR. - 20820.00 917 HR. - 39180.00 1834 HR. - 75860.00 2292 HR. - 94180.00 3668 HR. - 149220.00 5502 HR. - 222580.00 TOTAL - 601840.00
5.1.4(Carbon black, Toluene extract)	-	0.00	-
5.1.4(Carbon black, Volatile matter)	-	0.00	-
5.1.4(Carbon black, particle size)	-	0.00	-
5.1.4(Carbon black, Tint strength)	-	0.00	-
5.1.4(Carbon black, Density)	-	0.00	-
5.2.2(Film Form)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.3.2, Table 1(Impact Failure Mass)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.3.2, Table 1(Nominal Film Thickness)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.3.4(Elongation at Break)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.5, Annex D(U. V. Exposure (Service Life of Indian Solar Radiant Exposure 160 Kly))	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

Exclusion: Cl.5.6 (Solar Reflectance for Reflective Mulch Film)

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

16 TO 63 MM

10300.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.1(Maximum and minimum outside diameter of socket)	-	1000.00	-
7.1.1 Table-2(Length of Socket end)	-	0.00	ALL DIMENSION HAVE SINGLE CHARGE
7.1.2(Maximum and minimum outside diameter of conduit)	-	0.00	ALL DIMENSION HAVE SINGLE CHARGE
7.2(Minimum inside diameter of conduit)	-	0.00	ALL DIMENSION HAVE SINGLE CHARGE
7.4(Unifomity of The wall Thickness)	-	0.00	ALL DIMENSION HAVE SINGLE CHARGE
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	500.00	-
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	1000.00	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	1100.00	-
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	1000.00	-
10(Resistance to Heat -Ball presure test)	-	700.00	-
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	700.00	-
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1600.00	Test Charge-1100.00 SPECIMEN PREPARTION CHARGE- 500.00
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1600.00	Test Charge-1100.00 SPECIMEN PREPARTION CHARGE- 500.00
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	1100.00	-
6.1(Marking)	-	0.00	Test charges for above parameter Already Taken
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
6.3(Standard Mark on Conduit)	-	0.00	Test charges for above parameter Already Taken
7.3(Length of conduit)	-	0.00	Test charges for above parameter Already Taken
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980)	-	0.00	-
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980)	-	0.00	-
12(3 Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
12(3 Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
11.0(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
10.0(Resistance to Heat -Ball presure test)	-	0.00	Test charges for above parameter Already Taken
9.5 Fig.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
9.3(Compression Test (after removal of force) as per caluse 9.3.3 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
9.3(Compression Test at Full force applied (On load))	-	0.00	Test charges for above parameter Already Taken
9.2(Bending Test At Low Temp (-5 ±2°C))	-	0.00	Test charges for above parameter Already Taken
9.2(Bending Test At Room Temp)	-	0.00	Test charges for above parameter Already Taken
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
7.4(Unifomity of The wall Thickness)	-	0.00	Test charges for above parameter Already Taken
7.3(Length of conduit)	-	0.00	Test charges for above parameter Already Taken
7.2 Fig.3(Minimum inside diameter of conduit)	-	0.00	Test charges for above parameter Already Taken
7.1.2 Fig.2(Minimum outside diameter of conduit)	-	0.00	Test charges for above parameter Already Taken
7.1.2 Fig.1(Maximum outside diameter of conduit)	-	0.00	Test charges for above parameter Already Taken
7.1.1 Table-2(Length of Socket end)	-	0.00	Test charges for above parameter Already Taken
7.1.1 Fig.8(Maximum inside diameter of socket)	-	0.00	Test charges for above parameter Already Taken
7.1.1 Fig.7(Maximum outside diameter of socket)	-	0.00	Test charges for above parameter Already Taken
6.3(Standard Mark on Conduit)	-	0.00	Test charges for above parameter Already Taken
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	0.00	Test charges for above parameter Already Taken
6.1 - d(Marking)	-	0.00	Test charges for above parameter Already Taken
6.1 - c(Marking)	-	0.00	Test charges for above parameter Already Taken
6.1 - b(Marking)	-	0.00	Test charges for above parameter Already Taken
6.1 - a(Marking)	-	0.00	Test charges for above parameter Already Taken

Complete

IS 15351 (2015)

Agro textiles – Laminated high density polyethylene (HDPE) woven geomembrane for water proof lining – Specification (second revision)

TYPE I, II, III & IV

199950.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(HDPE Tapes)	-	2750.00	1. IDENTIFICATION OF TAPE- 1050.00 2. WIDTH OF TAPE - 500.00 3. LINEAR DENSITY OF TAPE - 700.00 4.TAPES PER DM WARP & WEFT DIRECTION - 500.00
3.2(HDPE Fabric)	-	3175.00	1. LAMINATION MATERIAL IDENTIFICATION - 1050.00 2. CARBON BLACK CONTENT - 925.00 3.CBD- 700.00 4. COATING THICKNESS OF LAMINATION/ COATING THICKNESS OF SANDWITCH LAMINATION- 500.00
5(MANUFACTURE)	-	500.00	-
5.1.1 and 6.2(Thickness, mm- IS 7016: Part 1)	-	500.00	-
5.1.1 and 6.2(Mass, g/sq m)	-	500.00	-
5.1.1 and 6.2(Dimensions, mm- Annexure A of IS 11652)	-	500.00	-
5.1.1 and 6.2(Carbon black content, Percent- IS 2530)	-	925.00	-
5.1.1 and 6.2(Breaking Load on 20 cm X 10 cm Strip, Min )	-	1100.00	-
5.1.1 and 6.2(Strain at Maximum load, Percent-IS 13162 (Part 5)	-	1100.00	-
5.1.1 and 6.2( U.V exposure of 1000 h for warp and weft)	-	176500.00	UV EXPOSURE9XENON ARC FOR 1000 HR.) CHARGE - 176500.00
Table-1(Breaking load on 20 × 10 cm strip, N, Min after)	-	1100.00	-
5.1.1 and 6.2(Impact failure load, at 1524 mm drop,)	-	1100.00	-
5.1.1 and 6.2(Tear resistance, N, Min-Method A1 of IS 7016 (Part 3))	-	1100.00	-
5.1.1 and 6.2(Puncture resistance, N, Min-Annex D)	-	1100.00	-
5.1.1 and 6.2(Bursting strength (Ball burst),N/cm², Min-)	-	1000.00	-
5.1.1 and 6.2(Seam strength before UV exposure (N/mm), Min-IS 15060)	-	1100.00	-
Table-1(Seam strength after UV exposure N/mm, Min-Annex B and IS 15060)	-	1100.00	-
5.1.1 and 6.2(Hydrostatic resistance-Annex E)	-	1000.00	-
Table-1(Hydrostatic resistance after UV exposure of 1000 h -Annex B and Annex E)	-	1000.00	-
5.1.1 and 6.2(Ash content, percent, Max-Annex F)	-	1200.00	-
5.1(Lamination)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.2(Panel Width)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.3(Joints/Seams)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.1.1 and 6.2(Length)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.1.1 and 6.2(Width)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.1.1 and 6.2(Before UV exposure IS 13162 (Part 5)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.1.1 and 6.2( Min, gram force at 50 percent failure-Annex C)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
5.1.1 and 6.2(IS 7016 (Part 6))	-	0.00	-

Complete

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

CATEGORY A 7 CATEGORY B

4700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Construction and workmanship)	-	300.00	-
7.2(Flow path in emitters)	-	300.00	-
7.3.1(Resistance to Hydrostatic pressure)	-	1000.00	-
7.4.1(Emitter Pull Out In-line emitters)	-	500.00	-
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	1000.00	-
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	1000.00	-
8.3(Determination of Emitter Exponent)	-	600.00	-

Complete

IS 7903 (2017)

Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision)

TYPE I, II, III, IV, V, VI, VII

78875.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1()	-	3050.00	Identification of Tape Material(Chemical Analysis)= 1050 UV Stabilizer Identification by FTIR= 2000
3.1(HDPE Tapes (Carbon Black Content))	-	925.00	-
3.1(HDPE Tapes (Presence of UV-stabiliser))	-	2500.00	-
3.2(HDPE Fabric (Material Identification))	-	1050.00	-
3.3(Eyelets)	-	500.00	-
3.4( Line/ Cord beading IS 7903)	-	500.00	-
4.0(Types IS 7903)	-	500.00	-
5.1.1(Lamination IS 7903)	-	1050.00	-
5.1.1(Coating Thickness)	-	500.00	-
5.1.1(Lamination IS 7903)	-	925.00	-
5.1.2(Lamination IS 7903)	-	500.00	-
5.2.1(Construction IS 7903)	-	500.00	-
5.3(Joint/Seam, IS 7903)	-	400.00	-
6.1 Table 1,i)(No of HDPE fabric layers ,IS 7903)	-	500.00	-
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	500.00	-
6.1 Table 1,v)(Mass of laminated fabric, Annex C , IS 7903)	-	500.00	-
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	1800.00	Test Charge- 1300.00 SPECIMEN PREPARATION CHARGE- 500.00
6.1 Table 1vi)(Breaking strength before UV exposure,weft, IS 1969 part 1)	-	1800.00	Test Charge- 1300.00 SPECIMEN PREPARATION CHARGE- 500.00
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	1100.00	-
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	1100.00	-
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	1100.00	-
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	1100.00	-
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	1100.00	-
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	19850.00	Test Charges - 850.00 Specimen Preparation Charges - 19000.00
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	1200.00	-
6.2(Length, IS 7903)	-	500.00	-
6.3(Water Proofness,IS 7941)	-	1000.00	-
6.3(Water Proofness, IS 7940)	-	5200.00	Test Charge- 1000.00 AGEING CHARGE -4200.00
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Warp, IS 13162 part 2& IS 1969 Part1 )	-	29050.00	Test Charge- 1300.00 Conditioning Charge= 27750.00
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Weft , IS 13162 part 2& IS 1969 Part1 )	-	1300.00	-
5.4(Fixing of Eyelets, IS 7903)	-	500.00	-
3.1()	-	500.00	-
3.1()	-	700.00	-
3.1()	-	1100.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.4(Fixing of Eyelets ,IS 7903)	-	0.00	-
6.1 Table 1,ii)(No of lamination layers, IS 7903)	-	0.00	-
6.1 Table 1, iii)(Total no of layers in the finished tarpaulin, IS 7903)	-	0.00	-
6.1 Table 1 vii)(Elongation at break of fabric,warp, IS 1969 Part 1)	-	0.00	-
6.1 Table 1 vii)(Elongation at break of fabric,weft, IS 1969 Part1)	-	0.00	-
6.2(Width, IS 7903)	-	0.00	-
6.2(height, IS 7903)	-	0.00	-
3.4( Line/ Cord beading IS 7903)	-	0.00	-
4.0(Types IS 7903)	-	0.00	-
5.1.2(Lamination IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.2.1(Construction IS 7903)	-	0.00	-
5.3(Joint/Seam, IS 7903)	-	0.00	-
5.4(Fixing of Eyelets, IS 7903)	-	0.00	-
5.4(Fixing of Eyelets ,IS 7903)	-	0.00	-
6.1 Table 1,i)(No of HDPE fabric layers ,IS 7903)	-	0.00	-
6.1 Table 1,ii)(No of lamination layers, IS 7903)	-	0.00	-
6.1 Table 1, iii)(Total no of layers in the finished tarpaulin, IS 7903)	-	0.00	-
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	0.00	-
6.1 Table 1,v)(Mass of laminated fabric, Annex C , IS 7903)	-	0.00	-
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	0.00	-
6.1 Table 1 vii)(Elongation at break of fabric,weft, IS 1969 Part1)	-	0.00	-
6.1 Table 1 vii)(Elongation at break of fabric,warp, IS 1969 Part 1)	-	0.00	-
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Warp, IS 13162 part 2& IS 1969 Part1 )	-	0.00	-
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Weft , IS 13162 part 2& IS 1969 Part1 )	-	0.00	-
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	0.00	-
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	0.00	-
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	0.00	-
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	0.00	-
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	0.00	-
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	0.00	-
6.2(Length, IS 7903)	-	0.00	-
6.2(height, IS 7903)	-	0.00	-
6.3(Water Proofness,IS 7941)	-	0.00	-
6.3(Water Proofness, IS 7940)	-	0.00	-
6.2(dimension(l))	-	0.00	-
6.2(dimension(w))	-	0.00	-
6.2(dimension(h))	-	0.00	-
3.3(Eyelets (Dimesnions) i) Starting thickness of metal Aluminium min ii) Outside dia of flange‘A’ iii) Flange formed height ‘B’ iv) Pierced dia ‘C’ v) Overall length ‘D’ vi) Internal dia of Barrel when closed ‘E’ min vii) Thickness of compressed material between eyelet and washer F’ max viii) Outside diameter of barrel under the flange‘G’ )	-	0.00	-
3.1(HDPE Tapes (Material Identification))	-	0.00	-
3.1()	-	0.00	-
4()	-	0.00	-
5.1.1(Carbon Black Content)	-	0.00	-
5.1.1(Sandwich lamination thickness)	-	0.00	-
5.1.1(Mass of Finished Tarpaulin)	-	0.00	-
5.1.1(UV Exposure (144 hrs))	-	0.00	-
5.1.1(Agening)	-	0.00	-
7(Marking)	-	0.00	-
6.1 Table 1vi)(Breaking strength before UV exposure,weft, IS 1969 part 1)	-	0.00	-
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	0.00	-
6.2(Width, IS 7903)	-	0.00	-

Complete

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

TYPE I & TYPE II

21930.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050.00	Optional (Applicable on Raw material)
4.2(Tapes – Width IS 6192 and IS 11197)	-	500.00	Optional (Applicable on Tape)
4.3(Sacks)	-	500.00	-
4.3.1(Bottom Seam)	-	500.00	-
4.5 and Table 1 i(Capacity)	-	500.00	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500.00	-
5.2 and Table 1 iii(Ends per dm )	-	500.00	-
5.2 and Table 1 iv(Picks per dm )	-	500.00	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500.00	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100.00	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1100.00	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100.00	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380.00	CONDITIOING CHARGE- 10180.00 TESTING CHARGE-2200.00
5.2 and Table 1 x(Ash content )	-	1200.00	-
4.2(Tapes – Linear Density )	-	500.00	Optional (Applicable on Tape)
3(TYPES)	-	0.00	-
4.2(Construction)	-	0.00	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0.00	-
4.3.1( The outer stitch)	-	0.00	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0.00	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0.00	-
4.3.1(stitches/dm)	-	0.00	-
4.3.2(Mouth)	-	0.00	-
4.4(Liner IS 10146 or IS 10910.)	-	0.00	-
4.4(Mass of the loose liner )	-	0.00	-
4.4(Width of the loose liner)	-	0.00	-
4.4(Length of the line)	-	0.00	-
4.4(Bottom seam of the loose liner)	-	0.00	-
4.4.1(Liner)	-	0.00	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0.00	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	0.00	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0.00	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0.00	-
3(TYPES)	-	0.00	-
4.1(Raw Material)	-	0.00	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0.00	-
4.2(Tapes – Linear Density )	-	0.00	-
4.2(Construction)	-	0.00	-
4.3(Sacks)	-	0.00	-
4.3.1(Bottom Seam)	-	0.00	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0.00	-
4.3.1( The outer stitch)	-	0.00	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0.00	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0.00	-
4.3.1(stitches/dm)	-	0.00	-
4.3.2(Mouth)	-	0.00	-
4.4(Liner IS 10146 or IS 10910.)	-	0.00	-
4.4(Mass of the loose liner )	-	0.00	-
4.4(Width of the loose liner)	-	0.00	-
4.4(Length of the line)	-	0.00	-
4.4(Bottom seam of the loose liner)	-	0.00	-
4.4.1(Liner)	-	0.00	-
4.5 and Table 1 i(Capacity)	-	0.00	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	0.00	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0.00	-
5.2 and Table 1 iii(Ends per dm )	-	0.00	-
5.2 and Table 1 iv(Picks per dm )	-	0.00	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	0.00	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	0.00	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	0.00	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	0.00	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	0.00	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0.00	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0.00	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0.00	-
5.2 and Table 1 x(Ash content )	-	0.00	-

Complete

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

12 TO 25 MM

12725.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	925.00	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700.00	-
6.3(General)	-	500.00	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1000.00	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1000.00	-
8.3.3(Flow Paths in Emitting Unit)	-	500.00	-
8.3.4(Spacing ofEmitter Units)	-	0.00	SPACING AND FLOW PATH HAVE SINGLE CHARGE
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1000.00	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1600.00	-
8.5(Resistance to Tension at Elevated Temperature)	-	1100.00	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	500.00	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	2800.00	1. ACCEPATNCE TEST - 1200.00 2. TYPE TEST - 1600.00
8.8(Determination of Emitting Unit Exponent)	-	600.00	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0.00	All Dimension have single Charge.
6.3(General)	-	0.00	All Dimension have single Charge.
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	0.00	-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	0.00	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	0.00	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	0.00	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	0.00	-
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	0.00	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0.00	-
6.2.2(Fittings)	-	0.00	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	0.00	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	0.00	-
8.2.2(Regulated Emitting Pipes)	-	0.00	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0.00	-
8.5(Resistance to Tension at Elevated Temperature)	-	0.00	-
8.5(Resistance to Tension at Elevated Temperature)	-	0.00	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	0.00	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0.00	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0.00	-
4.1 a(Identification)	-	0.00	-
4.1 a(Identification)	-	0.00	-
4.1 c(Volatile matter Extract)	-	0.00	-
4.1 d(Density)	-	0.00	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	0.00	-
4.2(Carbon black content)	-	0.00	-
4.2(Carbon black dispersion)	-	0.00	-
5.1(Materials)	-	0.00	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	0.00	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	0.00	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	0.00	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	0.00	-
6.2(Fittings)	-	0.00	-
6.3(General)	-	0.00	-
7.1(Test Specimens)	-	0.00	-
7.2(Order of Tests)	-	0.00	-
7.3(Testing Conditions)	-	0.00	-
7.4(Accuracy of Measuring Devices)	-	0.00	-
8.1(Uniformity of Emission Rate)	-	0.00	-
8.1.2(Unregulated Emitting Pipes)	-	0.00	-
8.1.3(Regulated Emitting Pipes)	-	0.00	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0.00	-
8.2.1(Unregulated Emitting Pipes)	-	0.00	-
8.2.2(Regulated Emitting Pipes)	-	0.00	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0.00	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0.00	-
8.3.3(Flow Paths in Emitting Unit)	-	0.00	-
8.3.4(Spacing of Emitter Units)	-	0.00	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	0.00	-
8.5(Resistance to Tension at Elevated Temperature)	-	0.00	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	0.00	-
8.7.1(Acceptance Test)	-	0.00	-
8.7.2(Type Test)	-	0.00	-
8.8(Determination of Emitting Unit Exponen)	-	0.00	-
9.1(Non-regulated Emitting Pipe)	-	0.00	-
9.2(Regulated Emitting Pipe)	-	0.00	-
10.1(Marking)	-	0.00	-

Complete

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

16 TO 200 MM

117150.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Colour)	-	500.00	-
Cl 7(Dimensions Of Pipes)	-	500.00	-
Cl 8(Visual Appearance)	-	500.00	-
Cl 9.1(Hydraulic Characteristics)	-	18400.00	1. 1Hr. at 20 deg - 1000.00 2. 22 Hr. at 95 deg. c - 1600.00 3. Type test 165 Hr. at 95 deg. C - 4800.00 4. type test 1000 Hr. at 95 deg. C - 11000.00
Cl 9.2(Fusion Compatibility)	-	4800.00	-
Cl 9.3(Reversion Test )	-	1200.00	Test Charges - 700.00 specimen Preparation Charge - 500.00
Cl 9.4 & Annex B(Impact Strength)	-	1600.00	Test Charges - 1100.00 specimen Preparation Charge - 500.00
Cl 9.5(Density)	-	700.00	-
Cl 9.6(Melt Flow Rate)	-	1100.00	-
Cl 9.7(Carbon Black Content & Dispersion)	-	1625.00	1. CBC - 925.00 2. CBD - 700.00
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	83825.00	1. TESTING CHARGE- 1700.00 2. CONDITIONING CHARGE - 82125.00
Cl 9.9(Opacity)	-	700.00	-
Cl 4( Designation)	-	0.00	-

Complete

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

40 TO 200 MM

64100.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	1125.00	Testing charge- 500.00 SPECIMEN PREPARATION CHARGE- 625.00
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1100.00	-
4.1 .1.2.1(HDPE couplers)	-	4700.00	1. OIT- 2200.00 2. VOLATILE MATTER- 700.00 3. WATER CONTENT- 700.00 4. TENSILE STRENGTH AT YIELD AND ELONGATION AT BREAK- 1100.00 & SPECIMEN PREPARATION CHARGE- 250.00
4.1.4(Holding attachments for coupler parts)	-	1625.00	1. CARBON BLACK CONTENT - 925.00 2. CARBON BLACK DISPERSION - 700.00
5(Dimensions of pipe - i) Outside diameter)	-	750.00	-
6.1(VISUAL APPEARANCE)	-	6325.00	1. OIT- 2200.00 2. VOLATILE MATTER- 700.00 3. WATER CONTENT - 700.00 4. TENSILE STRENGTH @ YIELD AND ELONGATION AT BREAK - 1100.00 & SPECIMEN CHARGE- 250.00 5. CBC- 925.00 6. CBD- 700.00
7.1(Hydraulic Characteristics - Quality test)	-	4800.00	-
7.1(Hydraulic Characteristics - Acceptance test)	-	1600.00	-
7.2(Reversion Test)	-	900.00	Test Charge- 700.00 Specimen Charge- 200.00
7.3(Tensile Test- i) Tensile Strength)	-	1100.00	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	9700.00	Quality Test @ 80° C for 165 Hrs. 4800.00 Acceptance Test @ 80 °C for 48 Hrs. 1600.00 Corrected Density 500.00 Melt Flow Rate (MFR) 1100.00
Cl.7.2.l(Leakage Test)	-	1500.00	Leakage Test for 1 Hrs. 850.00 Hydraulic proof Test for 1 Hrs. 850.00
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	6400.00	Quality Test @ 80° C for 165 Hrs. 4800.00 Acceptance Test @ 80 °C for 48 Hrs. 1600.00
7.3(Quick Couple Fitting)	-	6400.00	Quality Test @ 80° C for 165 Hrs. 4800.00 Acceptance Test @ 80 °C for 48 Hrs. 1600.00
7.2.1(Visual and Workmanship Requirement)	-	300.00	-
Cl.4.1.3, T-1(Volatile Matter)	-	700.00	-
Cl.4.1.3, T-1(Water Content)	-	700.00	-
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	1100.00	-
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	0.00	Elongation & Tensile have single charge.
6.2.4(Workmanship and appearance (Visual))	-	300.00	-
6.2.6(Material Identification (Chemical Analysis))	-	1050.00	-
6.2.6(Color)	-	300.00	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	4950.00	Hardness of rubber ring before ageing 375.00 Ageing @ 70° C for 7 days 4200.00 Shore hardness of Rubber Ring after ageing 375.00
5(Dimensions of pipe - ii) Wall thickness minimum)	-	-	-
6(Visual Appearance)	-	-	-
7.3(Tensile Test - ii)Elongation at Break)	-	-	-
7.4(Fusion Compatibility Test- a) Quality test)	-	-	-
7.5(Density)	-	-	-
7.6(Melt Flow Rate)	-	-	-
7.6(Melt Flow Rate)	-	-	-
4.2(Carbon black- a)carbon content)	-	-	-
4.2(Carbon black- b) Dispersion of carbon black)	-	-	-
7.6(Melt now Rate (MFR))	-	-	-
7.5(Density)	-	-	-
7.4 Table-2(Fusion Compatibility Test)	-	-	-
7.3(Tensile Test)	-	-	-
7.2(Reversion Test)	-	-	-
7.1 Table -2(Hydraulic Characteristics)	-	-	-
5.1.2(Ovality)	-	-	-
5.1 table -1(DIMENSIONS OF PIPES)	-	-	-
4.3(Anti-oxidant)	-	-	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	-	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	-	-
3(CLASSIFICATION OF PIPES)	-	-	-
4.1(Quick Coupled Male and Female Couplers)	-	-	-
4.1(Quick Coupled Male and Female Couplers)	-	-	-
4.1.3(Workmanship and appearance)	-	-	-
6.1.3(Weldability Test- a) Quality test)	-	-	-
6.1.3(Weldability Test- b) Acceptance test)	-	-	-
3(Quick Coupled pipes)	-	-	-
3(QUICK COUPLED PIPES)	-	-	-
4(QUICK COUPLED FITTINGS)	-	-	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	-	-
4.1 (b)(HDPE couplers —)	-	-	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	-	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	-	-
4.1 .1.2.2(HDPE couplers)	-	-	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	-	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	-	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	-	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	-	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	-	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	-	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	-	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	-	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	-	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	-	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	-	-
6.1(Quick Coupled Pipes and Fittings)	-	-	-
6.1.1, 6.1.1.1(Leakage Test)	-	-	-
6.1.1, 6.1.1.1(Leakage Test)	-	-	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	-	-
6.1.2.2(Hydraulic Proof Test)	-	-	-
6.1.3, 6.1.3.1(Weldability Test)	-	-	-
6.1.3.1.1(Weldability Test)	-	-	-
6.1.3.2(Quick coupled fittings)	-	-	-
6.2, 6.2.1(Quick Coupled Fittings)	-	-	-
6.2 b(Material Identification - Male & Female Coupler)	-	-	-
6.3.3(Material Identification - Insert Valve Coupler)	-	-	-
6.3.3(Material Identification - Insert Valve Coupler)	-	-	-
6.3.5(Material Identification - Saddle)	-	-	-
6.3.5(Material Identification - Pipe Ends)	-	-	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	-	-
4.2(Metallic Couplers)	-	-	-
4.2(Metallic Couplers)	-	-	-
7.2.1(Leakage Test)	-	-	-
Cl.4.1.3(Den sity Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(MFR Test)	-	-	-
Cl.4.1.3(Thermal Stabi lity)	-	-	-
Cl.4.1.3(Thermal Stabi lity)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Volatile Matter)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Content)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.4.1.4(Carbon Black Di spersion)	-	-	-
Cl.5(Di men sion)	-	-	-
Cl.5.1.l(Outside Diameter)	-	-	-
Cl.5.1.l(Outside Diameter)	-	-	-
Cl.6.2.L(Wall Thickness)	-	-	-
Cl.6.2.4(Workmanship and Appearance)	-	-	-
Cl.6.2.6(Rubber Ring Hardness)	-	-	-
Cl.6.2.6(Ageing Test)	-	-	-
Cl.7.1.l(Visual Anneara nce)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.2(Hydraulic Characteristic)	-	-	-
Cl.7.1.3(Reversion Test)	-	-	-
Cl.7.1.3(Reversion Test)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Tensile Test)	-	-	-
Cl.7.1.4(Elongation)	-	-	-
Cl.7.1.4(Elongation)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.5(Fusion Compatibility)	-	-	-
Cl.7.1.6(Corrected Density)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.1.7(MFR Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.7.2.2(Cl.7.2.2)	-	-	-
Cl.7.2.3(Weld ability Test)	-	-	-
Cl.7.2.3(Weld ability Test)	-	-	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	-	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	-	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	-	-
6.1(Thermal Stability (OIT))	-	-	-
6.1(Volatile Matter)	-	-	-
6.1(Water content)	-	-	-
6.1(Tensile strength at Yield & Elongation at break)	-	-	-
6.1(Carbon Black Content)	-	-	-
6.1(Carbon Black Dispersion)	-	-	-
6.2.1(Base Density x 2)	-	-	-
6.2.1(Melt Flow Index x 2)	-	-	-
6.2.1(Thermal Stability (OIT) x 2)	-	-	-
6.2.1(Volatile Matter x 2)	-	-	-
6.2.1(Water content x 2)	-	-	-
6.2.1(Carbon Black Content x 2)	-	-	-
6.2.1(Carbon Black Dispersion x 2)	-	-	-
6.2.1(Wall thickness of male & female coupler)	-	-	-
6.2.5(Holding attachment for coupler parts)	-	-	-
6.2.5(Material Composition (Chemical Analysis))	-	-	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	-	-
6.2.6(Ageing Charges for rubber ring)	-	-	-
7.1.1(Visual appearance of pipes)	-	-	-
7.1.2(Hydraulic Characteristics)	-	-	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	-	-
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
7.1.3(Reversion)	-	-	-
7.1.4(Tensile strength & elongation)	-	-	-
7.1.5(Fusion Compatibility test)	-	-	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	-	-
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
7.1.6(Corrected Density)	-	-	-
7.1.6(Base Density)	-	-	-
7.1.6(Carbon black Content)	-	-	-
7.1.7(Melt Flow Rate (MFR))	-	-	-
7.2.1(Leakage test 1hour / 27°C)	-	-	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	-	-
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	-	-
8(Supply of pipe (Visual))	-	-	-
4.1.1 (Table-1)(Density)	-	-	-
4.1.1 (Table-1)(Melt Flow Index)	-	-	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	-	-
4.1.1 (Table-1)(Volatile Matter)	-	-	-
4.1.1 (Table-1)(Water content)	-	-	-
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	-	-
4.1.4(Carbon Black Content)	-	-	-
4.1.4(Carbon Black Dispersion)	-	-	-
4.1.1(Polyethylene material)	-	-	-
4.1.3, Table 1,(i)(Bass density)	-	-	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	-	-
4.1.3, Table 1,(iii)(Thermal stability)	-	-	-
4.1.3, Table 1,(iv)(Volatile matter)	-	-	-
4.1.3, Table 1,(v)(Water content)	-	-	-
4.1.4(The Carbon Content and Dispersion)	-	-	-
4.1.5(Carbon Black Specification)	-	-	-
4.1.6(Antioxidant)	-	-	-
4.1.7(Rework Material)	-	-	-
4.2(Metallic Couplers)	-	-	-
5.1, Table 1,(i)(Plain pipes)	-	-	-
5.1, Table 1,(ii)(90° Bends and tee)	-	-	-
5.1, Table 1,(iii)(Base pipe )	-	-	-
5.1, Table 1,(iv)(PCN)	-	-	-
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	-	-
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	-	-
5.1, Table 1,(vii)(Riser pipe and socket)	-	-	-
7.1.1(Visual Appearance and Workmanship)	-	-	-
7.1.2(Hydraulic Performance Characteristic)	-	-	-
7.1.3(Reversion Test)	-	-	-
7.1.4(Tensile Test)	-	-	-
7.1.5(Fusion Compatibility Test)	-	-	-
7.1.6(Corrected Density)	-	-	-
7.1.7(Melt flow rate)	-	-	-
7.2.1(Leakage Test)	-	-	-
7.2.2(Hydraulic Proof Test)	-	-	-
7.2.3(Weldability Test)	-	-	-
10(Marking)	-	-	-
5.1.2(Squareness)	-	-	-
6.1.2.2(Hydraulic Proof Test)	-	-	-
6.3.4()	-	-	-
Cl.7.2.l(Leakage Test)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-
Cl.4.1.3, T-1(Water Content)	-	-	-

Complete

Exclusion: Holding attachements for Coupler parts

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

15 TO 150 MM

150250.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	500.00	-
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	0.00	ALL DIMENSION HAVE SINGLE CHARGE.
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	0.00	ALL DIMENSION HAVE SINGLE CHARGE.
7.1.3 (Effective length)	-	0.00	ALL DIMENSION HAVE SINGLE CHARGE.
8(Pipe Ends)	-	500.00	-
9.1(Visual Appearance)	-	500.00	-
9.2 IS 12235 (Part 3)(Opacity)	-	700.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	3000.00	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	700.00	-
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1100.00	-
9.6 IS 12235(Part 14)(Density)	-	700.00	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	850.00	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	4800.00	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	11000.00	-
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	110500.00	Test Charge- 1000.00 SPECIMEN CONDITIOING CHARGE- 109500.00
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1600.00	Test Charge- 1100.00 SPECIMEN PREPARATION CHARGE-500.00
10.4 IS 12235(Part 19)(Flattening Test)	-	500.00	-
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1800.00	Test Charge- 1300.00 SPECIMEN PREPARATION CHARGE- 500.00
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	11500.00	Test Charge- 11000.00 SPECIMEN PREPARATION CHARGE- 500.00
6.2.1 Annex B(Chloride Content of Resin)	-	4300.00	Optional Applicable on raw material
6.3(Compound Properties)	-	17475.00	Optional Applicable on raw material - Total Charge 17475
5 Table 1(Classification of pipes)	-	0.00	-
6.3.1 Annex B(Chloride content)	-	0.00	-
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	0.00	-
9(PHYSICAL AND CHEMICAL CHARACTERISTICS)	-	0.00	-
9.1(Visual Appearance)	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0.00	-
10(Mechanical Properties)	-	0.00	-
5 Table 1(Classification of pipes)	-	0.00	-
6.2.1 Annex B(Chloride Content of Resin)	-	0.00	-
6.3(Compound Properties)	-	0.00	-
6.3.1 Annex B(Chloride content)	-	0.00	-
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	0.00	-
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	0.00	-
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	0.00	-
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	0.00	-
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	0.00	-
7.1.3 (Effective length)	-	0.00	-
8.0(Pipe Ends)	-	0.00	-
9.0(PHYSICAL AND 1CHARACTERISTICS)	-	0.00	-
9.1(Visual Appearance)	-	0.00	-
9.1(Visual Appearance)	-	0.00	-
9.2 IS 12235 (Part 3)(Opacity)	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0.00	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0.00	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	0.00	-
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	0.00	-
9.6 IS 12235(Part 14)(Density)	-	0.00	-
10.0(Mechanical Properties)	-	0.00	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0.00	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0.00	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0.00	-
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	0.00	-
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	0.00	-
10.4 IS 12235(Part 19)(Flattening Test)	-	0.00	-
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	0.00	-
7.1.2(Wall Thickness (Maximum))	-	0.00	-
7.1.1(Outside Diameter at any point (Maximum))	-	0.00	-
6.3(K value Test)	-	0.00	-
6.3.3(Density)	-	0.00	-

Complete

IS 15907 (2010)

Agro textiles – High density polyethylene (HDPE) woven beds for vermiculture – Specification

102380.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Cord Beading - IS 15907)	-	500.00	-
4.1(Identification)	-	2000.00	-
4.1(Width)	-	500.00	-
4.1(Linear Density)	-	700.00	-
5.2.1(Lamination- IS 15907)	-	2000.00	-
5.2.1(Thickness of coating film- method A of IS 13162 (Part 3))	-	500.00	-
5.2.1(Lamination- IS 15907)	-	500.00	-
5.3.1(Construction- IS 15907)	-	500.00	-
5.3.1(Construction- IS 15907)	-	500.00	-
5.3.1(Construction- IS 15907)	-	2000.00	-
5.3.1(Construction- IS 15907)	-	2000.00	-
5.3.2(Construction- IS 15907)	-	500.00	-
5.3.2(Construction- IS 15907)	-	500.00	-
5.3.2(Construction- IS 15907)	-	500.00	-
5.3.2(Construction- IS 15907)	-	500.00	-
5.4(Bonding- IS 15907)	-	500.00	-
6- Table 1- SL.No (i)(Mass)	-	500.00	-
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,warp - IS 1969 )	-	1800.00	Test Charge- 1300.00 SPECIMEN CHARGE- 500.00
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,weft - IS 1969 )	-	1300.00	-
6- Table 1- SL.No (iv)(Retention of breaking strength after UV exposure, - Annex B of IS 15907 and IS 1969)	-	2600.00	-
6- Table 1- SL.No (v)(Welded seam strength before UV exposure- IS 1969)	-	1600.00	Test Charge- 1100.00 SPECIMEN CHARGE- 500.00
6- Table 1- SL.No (vi)(Welded seam strength after UV exposure- Annex B of IS 15907 and IS 1969)	-	1100.00	-
6- Table 1- SL.No (vii)(Tear strength, Warp - Method A2 of IS 7016 (Part 3))	-	1600.00	Test Charge- 1100.00 SPECIMEN CHARGE- 500.00
6- Table 1- SL.No (vii)(Tear strength, Weft - Method A2 of IS 7016 (Part 3))	-	1100.00	-
6- Table 1- SL.No (viii)(Puncture strength - Annex C of IS 15907)	-	1100.00	-
6- Table 1- SL.No (ix)(Environmental stress cracking test - Annex D of IS 15907)	-	2000.00	Test Charge- 1500.00 SPECIMEN CHARGE- 500.00
6- Table 1- SL.No (x)(Resistance to chemicals, change in the mass - Annex E of IS 15907)	-	2500.00	Test Charge- 2000.00 SPECIMEN CHARGE- 500.00
6- Table 1- SL.No (xi)(Colour fastness to artificial light -IS 2454)	-	19850.00	TEST CHARGE- 850 SPECIMEN CONDITIONING CHARGE- 19000.00
6- Table 1- SL.No (xii)(Bursting pressure-IS 1966)	-	1600.00	Test Charge- 1100.00 SPECIMEN CHARGE- 500.00
6.1(Length -IS 15907)	-	500.00	-
6.1(Width - IS 15907)	-	500.00	-
6.1(Height - IS 15907)	-	500.00	-
6.2(Water Proofness,IS 7941)	-	1500.00	Test Charge- 1000.00 SPECIMEN CHARGE- 500.00
6.2(Water Proofness, IS 7940)	-	1000.00	-
5.1(MANUFACTURE- IS 15907)	-	0.00	-
5.2.2(Lamination- IS 15907)	-	0.00	-
5.2.2(Lamination- IS 15907)	-	0.00	-
5.2.2(coating thickness of the sandwich lamination- method A of IS 13162 (Part 3))	-	0.00	-
5.3.1(The width of the hem - IS 15907)	-	0.00	-
5.3.1(Construction- IS 15907)	-	0.00	-
5.3.1(Construction- IS 15907)	-	0.00	-
5.3.1(Construction- IS 15907)	-	0.00	-
5.3.2(Finished width of pocket - IS 15907)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
6- Table 1- SL.No (iii)(Elongation at break of fabric- IS 1969)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

IS 10889 (2004)

High density polyethylene films (First Revision)

GRADE 1 & GRADE 2

8925.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1(Appearance)	-	500.00	-
6.1.2(Film Form)	-	0.00	APPERANCE, FILM FORM & ODOUR HAVE SINGLE CHARGE.
6.1.3(Odour )	-	0.00	APPERANCE, FILM FORM & ODOUR HAVE SINGLE CHARGE.
6.1.4(Density)	-	700.00	-
6.1.5(Melt Flow Rate)	-	1100.00	-
6.1.6(Black Film)	-	1625.00	1. CBC- 925.00 2. CBD - 700.00
6.2.1, Table 1(Nominal Thickness)	-	500.00	-
6.2.2, Table 2(Nominal Width)	-	500.00	-
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	0.00	-
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	0.00	-
6.3, Table 3(Yield Tolerance)	-	600.00	-
6.4.1(Tensile Strength at Break)	-	2600.00	-
6.4.3(Impact Resistance (Falling Dart))	-	850.00	-
4.0(Grades)	-	0.00	Testing charges for this parameter already taken.
5.1(Materials)	-	0.00	Testing charges for this parameter already taken.
5.2(Black Compound)	-	0.00	Testing charges for this parameter already taken.
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	0.00	Testing charges for this parameter already taken.
6.4.1, Table 4(Direction)	-	0.00	Testing charges for this parameter already taken.
6.4.1, Table 4(Grade 1 and 2)	-	0.00	Testing charges for this parameter already taken.
6.4.2, Table 5(Direction)	-	0.00	Testing charges for this parameter already taken.
6.4.2, Table 5(Elongation at Break, Percent Grade 1 and 2)	-	0.00	Testing charges for this parameter already taken.
6.4.2(Elongation at Break)	-	0.00	Testing charges for this parameter already taken.
6.4.3, Table 6(Average Thickness of Film)	-	0.00	Testing charges for this parameter already taken.
6.4.3, Table 6(Impact Failure Load)	-	0.00	Testing charges for this parameter already taken.

Complete

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

TYPE I, TYPE -II, TYPE III, TYPE IV TYPE V

21430.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050.00	Optional (Applicable on Raw material)
4.2(Tapes – Width IS 6192 and IS 11197)	-	500.00	Optional (Applicable on Tape)
4.3(Sacks)	-	500.00	-
4.4 and Table 1 i(Capacity)	-	500.00	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500.00	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0.00	LENGTH & WIDTH HAVE SINGLE CHARGE.
5.2 and Table 1 iii(Ends per dm )	-	500.00	-
5.2 and Table 1 iv(Picks per dm )	-	500.00	-
5.1 and Table 1 v(Mass of sack )	-	500.00	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100.00	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100.00	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100.00	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380.00	1. UV EXPOSURE - 10180.00 2. BREAKING STRENGTH (LENGTH WISE) - 1100.00 3. BREAKING STRENGTH (WIDTH WISE) - 1100.00
5.2 and Table 1 x(Ash content )	-	1200.00	-
3(TYPES)	-	0.00	-
4.2(Tapes – Linear Density )	-	0.00	-
4.2(Construction)	-	0.00	-
4.3.1(Bottom Seam)	-	0.00	-
4.3.1( The two rows of stitches shall be separated from each other)	-	0.00	-
4.3.1( The outer stitch)	-	0.00	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0.00	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0.00	-
4.3.1(The number of stitches/dm)	-	0.00	-
4.3.2(Mouth)	-	0.00	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0.00	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0.00	-
3(TYPES)	-	0.00	-
4.1(Raw Material)	-	0.00	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0.00	-
4.2(Tapes – Linear Density )	-	0.00	-
4.2(Construction)	-	0.00	-
4.3(Sacks)	-	0.00	-
4.3.1(Bottom Seam)	-	0.00	-
4.3.1( The two rows of stitches shall be separated from each other)	-	0.00	-
4.3.1( The outer stitch)	-	0.00	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0.00	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0.00	-
4.3.1(The number of stitches/dm)	-	0.00	-
4.3.2(Mouth)	-	0.00	-
4.4 and Table 1 i(Capacity)	-	0.00	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	0.00	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0.00	-
5.2 and Table 1 iii(Ends per dm )	-	0.00	-
5.2 and Table 1 iv(Picks per dm )	-	0.00	-
5.1 and Table 1 v(Mass of sack )	-	0.00	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	0.00	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	0.00	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	0.00	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0.00	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0.00	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0.00	-
5.2 and Table 1 x(Ash content )	-	0.00	-

Complete

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

35 TO 400 MM

12600.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	1500.00	Test Charge- 1000.00 specimen Charge- 500.00
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	500.00	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500.00	-
8.4(Sealing rings - Hardness)	-	500.00	-
9.1( Visual Appearance)	-	500.00	-
9.2(Internal Diameter)	-	500.00	-
9.3(Density IS 12235 (Part 14))	-	700.00	-
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1500.00	Test Charge- 1000.00 SPECIMEN CHARGES- 500.00
9.5(Tensile Strength IS 12235(Part 13))	-	1800.00	Test Charge- 1300.00 SPECIMEN CHARGES- 500.00
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100.00	-
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000.00	-
4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating )	-	1100.00	-
5(COLOUR)	-	0.00	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	0.00	-
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	0.00	-
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	0.00	-
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	3000.00	-
9.1(Visual Appearance)	-	0.00	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0.00	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0.00	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0.00	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0.00	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0.00	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0.00	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	0.00	-
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	0.00	-
7.4 Table 8 & 9 Fig 1(Segmental length, l5)	-	0.00	-
7.4 Table 8 & 9 Fig 1(Segmental length, l4)	-	0.00	-
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	0.00	-
7.3.2(Rib height)	-	0.00	-
7.3.1(No.of Ribs)	-	0.00	-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	0.00	-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0.00	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	0.00	-
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	0.00	-
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0.00	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	0.00	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0.00	-
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	0.00	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	0.00	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0.00	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	0.00	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	0.00	-
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	0.00	-
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	0.00	-
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	0.00	-
8.4(Width b)	-	0.00	-
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	0.00	-
8.2(Threading of casing pipe As per IS 554 (from 40 to 80mm DN) Number of threads in 25.4mm Pitch (P) Height of thread (h) Major (Gauge Diameter) d Pitch(d2) Minor (d1) External Thread gauge length Nominal No. of turns of thread max min )	-	0.00	-
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	0.00	-
5.0(Colour of Pipes)	-	0.00	-
4.1.2(K-Value as per IS-4669)	-	0.00	-
7.1(Screen Pipes)	-	0.00	-
11(Marking)	-	0.00	-
8(Packing)	-	0.00	-
4.1.3(Cross Chain Length)	-	0.00	-
7.2(Link Twisted (Cross chain))	-	0.00	-
7.3(The Basic chains)	-	0.00	-
7.9(Case Depth)	-	0.00	-
8(Marking)	-	0.00	-
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	0.00	-
5.1(Materials)	-	0.00	-

Complete

Exclusion: Cl 4.1.1 (VCM Content as per IS 10151 (Annex A))

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

TYPE I, TYPE II, TYPE III, TYPE IV

20575.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	500.00	-
5.1.2(Film Form)	-	0.00	APPEARNCE , FILM FORM & ODOUR HAVE SINGLE CHARGE.
5.1.3(Odour)	-	0.00	APPEARNCE , FILM FORM & ODOUR HAVE SINGLE CHARGE.
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	700.00	-
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100.00	-
5.1.6a(Carbon Black Content, Annex-A)	-	925.00	-
5.1.6b(Ash Content, Annex-A)	-	1200.00	-
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700.00	-
5.2.2(Tolerance on Thickness, Annex-A)	-	500.00	-
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1800.00	Test Charge- 1300.00 SPECIMEN CHARGE- 500.00
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1300.00	-
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	0.00	CONDITIONING XCHARGE- - 4200.00
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1300.00	Test Charge- 1300.00
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1300.00	-
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	850.00	-
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1100.00	Test Charge- 1100.00 SPECIMEN CHARGE- 500.00
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1100.00	-
8.1, Table 3(Puncture resistance , Annex C)	-	1100.00	Applicable on Type 3 & Type 4
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0.00	-
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0.00	-
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	0.00	-
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	0.00	-
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0.00	-
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0.00	-
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0.00	-
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0.00	-
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0.00	-
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0.00	-
8.1, Table 3(Tear resistance , Annex B)	-	0.00	-
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0.00	-
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0.00	-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0.00	-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0.00	-
9.1, Table 4(Tear resistance , Annex B)	-	0.00	-
9.1, Table 4(Puncture resistance , Annex C)	-	0.00	-
Clause 9.1 (Table 4)(Break Elongation)	-	0.00	-
Clause 9.1 (Table 4)(Yield Elonation)	-	0.00	-
Clause 9.1 (Table 4)(Break strength)	-	0.00	-
Clause 9.1 (Table 4)(Yield strength)	-	0.00	-
Clause 8.1(Table 3)(Break Elongation)	-	0.00	-
Clause 8.1(Table 3)(Break strength)	-	0.00	-
Clause 7.1(Table 2)(Dart Impact Strength)	-	0.00	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0.00	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0.00	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0.00	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0.00	-
Clause 5.2.3(Tolerance on Width)	-	0.00	-
Cl.5.1.6(a)(Carbon Black Content)	-	0.00	-
Cl.5.1.6(b)(Ash content)	-	0.00	-
Cl.5.1.6(c)(Dispersion of Carbon Black)	-	0.00	-
5.2.1.1(Nominal Thickness)	-	0.00	-
5.2.1.2(Nominal width)	-	0.00	-

Complete

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

12 MM TO 32 MM

10825.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2a(Carbon Black Content)	-	925.00	-
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700.00	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	500.00	-
6.1(Visual Appearance)	-	500.00	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	1000.00	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	3000.00	-
7.2(Reversion Test)	-	1200.00	Test Charge- 700.00 SPECIMEN CHARGE- 500.00
7.3(Tensile Test)	-	1800.00	Test Charge- 1300.00 SPECIMEN CHARGE-500.00
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200.00	-
4.1.a (Potyethylene - higher olefins constituent )	-	1050.00	ON RAW MATERIAL (OPTIONAL)
4.1.c.i (Density)	-	1125.00	Test Charge-500.00 SPECIMEN CHARGE- 625.00 ON RAW MATERIAL (OPTIONAL)
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925.00	ON RAW MATERIAL (OPTIONAL)
4.1.c(iv)(MATERIAL)	-	1100.00	ON RAW MATERIAL (OPTIONAL)
4.1.b(Potyethylene - anti-oxidant)	-	0.00	-
4.1.c.ii (Toluene extract - Annex A)	-	0.00	-
4.1.c.iii (Volatile matter - Annex B )	-	0.00	-
4.3(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0.00	-
7.3(Elongation at Break)	-	0.00	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0.00	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	0.00	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0.00	-
7.2(Reversion Test)	-	0.00	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	0.00	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0.00	-
7.2(Reversion Test)	-	0.00	-
7.1(Hydraulic Characteristics)	-	0.00	-
7.1(Hydraulic Characteristics)	-	0.00	-
3.1(Class of Pipe)	-	0.00	-
9.0 (9.1)(Minimum Internal Diameter of Coil)	-	0.00	-
9.0 (9.1)(Coiling )	-	0.00	-
8.0 (8.1) (Supply of pipes )	-	0.00	-
6.0 (6.1) (Visual appearance)	-	0.00	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	0.00	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	0.00	-
5.0 5.1 (Table1) (b)Tolerance on OD)	-	0.00	-
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	0.00	-
Cl. 4.2(Carbon Black Content)	-	0.00	-
Cl. 4.2(Carbon Black Dispersion)	-	0.00	-
Cl. 5.0 & 5.1 Table -1(Outside Diameter)	-	0.00	-
Cl. 5.0 & 5.1 Table -1(,Tolerence,)	-	0.00	-
Cl. 5.0 & 5.1 Table -1(Wall Thckness)	-	0.00	-
Cl. 7.1 Table -2(Quality Test for 100 hrs @ 70 c & 2.2 Mpa)	-	0.00	-
Cl. 7.1 Table -2(Acceptance Test for 1 hrs @ 27 c & 6.9 Mpa)	-	0.00	-
Cl. 7.3(Tensile Test)	-	0.00	-
Cl. 7.3(Elongation)	-	0.00	-
Cl. 8.0- 8.1(Supply of pipes)	-	0.00	-
Cl. 9.0 - 9.1(Minimum Internal Diameter of Coil)	-	0.00	-
4.1d(MATERIAL)	-	0.00	-
7.4(SusceptibiIity to Environmental Stress)	-	0.00	-
4(MATERIAL)	-	0.00	-
5.1(Diameters and wall thicknesses)	-	0.00	-
6(VISUAL APPEARANCE)	-	0.00	-
7.1(Hydraolic Characteristics)	-	0.00	-
7.2(Reversion Test)	-	0.00	-
7.3(Tensile Test)	-	0.00	-
7.3.1(Test Piece)	-	0.00	-
7.3.2(Procerdure)	-	0.00	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0.00	-
8(SUPPLY OF PIPES)	-	0.00	-
9(COILING)	-	0.00	-
11(Marking)	-	0.00	-

Complete

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

20- 630 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY- 700.00 2. SHORT TERM HYDROSTATIC - 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Table 2(Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-	500.00	-
3.2.2, Table 1(Dimension of 11 1/4° bends)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.2.3(Socket, Measurement)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

20 TO 630 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY - 700.00 2. SHORT TERM HYDROSTATIC - 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Table 1(Dimensions of 22 ½ deg Bends)	-	500.00	-
3.2.2, Table 2(Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.2.3(Socket, measurements)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

20 - 315 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY- 700.00 2. SHORT TERM HYDROSTATIC - 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Table 1(Dimensions of 30 deg Bends)	-	500.00	-
3.2.2, Table 2(Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-	0.00	-

Complete

VCM Content

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

20 TO 315 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY - 700.00 2. SHORT TERM HYDROSTATIC - 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Fig 1, table 1(Dimensions)	-	500.00	-
3.2, 3.2.1, Fig 2(Manufacture)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 45o Bend)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 45° Bend for Elastomeric Sealing Ring Joint)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

20 TO 315 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY - 700.00 2. SHORT TERM HYDROSTATIC - 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Fig 1, table 1(Dimensions)	-	500.00	-
3.2, 3.2.1, Fig 2(Manufacture)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 1 (Clauses 3.2.2, 3.2.3, and Fig. 1)(Dimensions of 60o Bends)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 60o Bend for Elastomeric Sealing Ring Joint)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

20 TO 630 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY- 700.00 2. SHORT TERM HYDROSTATIC- 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Fig 2, table 2(Dimensions)	-	500.00	-
3.2, 3.2.1, Fig 2(Manufacture)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

20 TO 315 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY- 700.00 2. SHORT TERM HYDROSTATIC- 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.3.2, table 1, fig 1(Dimensions)	-	500.00	-
3.2(Materials)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.3, 3.3.1, Fig 1(Manufacture)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.3.3(socket measurement shall comply with IS 10124 (Part 1).)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

20 TO 315 MM

6050.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY- 700.00 2. SHORT TERM HYDROSTATIC - 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Fig 2, table 2(Dimensions)	-	500.00	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500.00	-
3.2, 3.2.1, Fig 1(Manufacture)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 2 (Cl.3.2.2, and Fig.1)(Dimensions of Flanged Tail Piece with Metallic Flange for Elastomeric Sealing Ring Joint)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

20 to 315 mm

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY- 700.00 2. SHORT TERM HYDROSTATIC - 850.00, 500.00 3. EFFECT ON WATER- 3000.00
3.2.2, Fig 1(Dimensions)	-	500.00	ALL DIMENSION HAVE SINGLE CHARGE
3.2, 3.2.1, Fig 1(Manufacture)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Equal Tees)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

20 - 315 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY- 700.00 2. SHORT TERM HYDROSTATIC PRESSURE TEST- 850.00 & SPECIMEN PREPARATION CHARGE- 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Fig 1(Dimensions)	-	500.00	All dimensions have single charge.
3.1(General)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.2, 3.2.1, Fig 1(Manufacture)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

20 - 630 MM

5550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	5050.00	1. OPACITY- 700.00 2. SHORT TERM HYDROSTATIC TEST- 850.00, 500.00 3. EFFECT ON WATER - 3000.00
3.2.2, Fig 1(Dimensions)	-	500.00	All dimensions have Single Charge.
3.2, 3.2.1, Fig 1(Manufacture)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

20 to 630 mm

4925.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	1100.00	Optional on raw material 1. K-value- 1100.00
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500.00	all dimension have single charge.
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	0.00	all dimension have single charge.
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	0.00	all dimension have single charge.
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	0.00	all dimension have single charge.
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	575.00	-
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	850.00	-
6.3(Effect on water test)	-	3000.00	-
8(Marking)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.1(Material)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
4(Size of fitting)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.
3.2.3(socket, measurements)	-	0.00	TEST CHARGES FOR ABOVE PARAMETER ALREADY TAKEN.

Complete

VCM Content

Bureau of Indian Standards

The National Standards Body of India

Central Institute of Petrochemicals Engineering & Technology (CIPET), CSTS - Dehradun

CIPET : Centre for Skilling and Technical Support (CSTS), Haridwar Road, Post-Bhaniyawala, Doiwala, Dehradun, Dehradun, Dehradun, Uttarakhand, 248140

7457001351 testing.cipetdehradun@gmail.com

Scope List