BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- erol@bis.gov.in

Scope List

Reset

287 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause - 7.1 (CARBON)	-

Partial

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

For all nominal Dia

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.3 (Vicat softening tempewrature)	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-
Cl.15, Annex B (Sulphated Ash Content)	-
Cl.14, Annex A (Titanium Di-Oxide Content)	-
19 (Marking)	-
4 (Size Designation)	-
5 (Colour of fittings)	-
7.1,Table 1 (Wall thickness)	-
7.2 ,Table 2&3 (Socket Dimensions)	-
7.3 (Dimensions of waste trap(Nahani Trap)	-
8 (Sealing Rings)	-
10 (Workmanship)	-
11.4,Table 5 (Vent cowl)	-
11.5,Table 6 (Pipe Clips)	-
12.1 (Visual appearance)	-
12.2 (Stress relief test)	-
12.3 (Vicat softening tempewrature)	-
16.1 (Impact test)	-
7.4 (Chamfer)	-

Partial

Except Water Tightness of joints, Effect on Water.

IS 5082 (1998)

Wrought aluminium and aluminium alloy bars, rods, tubes, sections, plates and sheets for electrical applications (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1, Table 1 (Copper)	-
6.1, Table 1 (Magnesium)	-
6.1, Table 1 (Silicon)	-
6.1, Table 1 (Manganese)	-
6.1, Table 1 (Zinc)	-
6.1, Table 1 (Titanium)	-
6.1, Table 1 (Chromium)	-
6.1, Table 1 (Iron)	-
Clause 5 (FREEDOM FROM DEFECTS)	-
8.1 (MECHANICAL TEST Tensile Strength Min, Mpa)	-
8.1 (MECHANICAL TEST (0.2 Percent Proof Stress Min, Mpa))	-
8.1 (Percent Elongation on 5.65 Min)	-
8.2 (Bend Test)	-
8.1 (Maximum Electrical Resistivity at 20°C ohm-mm/mm2)	-

Partial

Chemical : Except Al, V and others elements

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

For all

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (DESIGN)	-
7.1.1 (Whole Footwear)	-
7.1.2 (Upper to Mid Sole/Out Sole Bond Performance)	-
7.1.3 ("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-
7.1.4 (Out Sole to Mid Sole (Multilayer) Bond Performance)	-
7.1.5 (Energy Absorption at Seat Region)	-

Partial

Except Flexing resistance table 2, Colour fastness rubbing table 2, Slip Resistance (Cl 7.1.8), Colour fastness to light table 2, Flexing resistance table 3, Colour fastness to light table 3, Flexing index(Only applicable for cellulose board) as per Table 5, Counter stiffener as per Table 9, Peel strength & Shear strength as per Table 10, Colour fastness to water of table 12

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

For all type

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5, Table -1 S. No-(i) (Amendment No-1) (Insole)	-
Cl-5, Table -1 S. No- (ii) (Amendment No-1) (Toe spring height)	-
Cl-5, Table -1 S. No- (iii) (Amendment No-1) ("Bond performance (a) Upper to sole/mid sole/composite sole (b) Interlayer bond strength")	-
Cl-5, Table -1 S. No- (iv) (Amendment No-1) (Energy absorption at seat region)	-
Cl-5, Table -1 S. No- (viii) (Amendment No-1) ("Abrasion resistance a-Cellular sole b-Solid sole")	-
Cl-5, Table -1 S. No- (xi) (Amendment No-1) (Hydrolysis resistance)	-

Partial

Except Slip resistance(4.9), Flexing Resistance(Table 1), Colour fastness to Rubbing(Table 1), Colour fastness to light(Table 1), Flexing resistance-Wet & Dry, Bursting strength, Flexing Index, Counter Stiffner, Colour Fastness to Water, Polychlorophenol (Chem)

IS 10805 (2022)

Foot-Valves, Reflux Valves or NonReturn Valves and Bore Valves to be Used in Suction Lines of Agricultural Pumping Systems â Specification ( Second Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Dimensions)	-
5.3 (Flange Dimensions)	-

Partial

Mechanical: Test facility not available for Seat Test, Housing Test, K-value test, frictional loss. Declaration required for nominal size of pipe and valve.

IS 17753 (2021)

Paperbased Multilayer Laminated/Extruded Composite Cartons (Aseptic and Non-Aseptic) for Processed Liquid Food Products and Beverages Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2.1 (Over-all Migration)	-
5.2.2 (Specific Migration Test)	-
5.1.1 (Description)	-
5.2.7 (Ink Adhesion Test)	-
5.2.6 (Print Resistance Test)	-
4.3 (Capacity)	-
4.1 Table 1 (i) (Grammage of paperboard, g/m2 , Max)	-
4.1 Table 1 (ii) (Thickness of aluminium foil, microns, Max)	-
4.1 Table 1 (iii) (Thickness of polyethylene, microns, Max)	-
5.2.3 (Vibration Leakage Test)	-
Cl 5.2.4.2 Table 3 (Shelflife Test)	-
Cl 5.2.4.3 Table 4 Sl.No.-i (Total bacterial count, CFU/g, Max)	-
Cl 5.2.4.3 Table 4 Sl.No.-ii (Total spore count, CFU/g, Max)	-
Cl 5.2.4.3 Table 4 Sl.No.-iii (Yeast and mould, CFU/100 cm2 , Max)	-

Partial

Excluding Cl 4.1-4.1.4 (material & Construction), cl 5.2.5 [Water Vapour Transmission Rate (WVTR) and Oxygen Transmission Rate (OTR)]

IS 6719 (1972)

Solid Pvc Soles And Heels

For all

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.6.1 (Hardness )	-
3.6 (i) (Relative density )	-
3.6 (v) (Volatility, percent by means )	-
Table 1 (Flexing resistance) (Table 1 (Flexing resistance, Bennewart method, cut growth at the end of 30 000 cycles, mm, Max))	-
Table 1 (Abrasion resistance) (Abrasion resistance at applied force of 10 N (volume loss), mm3, Max)	-
Cl. 6.4 (Measurement of thickness)	-
3.6 (iv) (Tear Strength a) Force Part b) Back Part )	-
Cl. 3.1,3.2,3.3,3.4,3.5 (Material)	-

Partial

Mech- Complete

IS 15298 : part 4 (2024)

Personal Protective Equipment Part 4 Occupational Footwear (ISO 20347 : 2021, MOD) (Third Revision)

For all class, design and size

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.2 (Design)	-
Cl 5.2.2 (" Height of upper ")	-
Cl 5.2.3 (Heel area)	-
Cl 5.3.1.1 (Construction of whole footwear)	-
Cl 5.3.1.2 (Upper/outsole bond strength)	-
Cl 5.3.2 (Leak proofness)	-
Cl 5.3.3 (Specific ergonomic features)	-
Cl 5.3.6 (Seam strength)	-
Cl 5.4.1.1 (Class I footwear, determination of the area where upper requirements apply of Upper)	-
Cl 5.4.1.2 (Hybrid footwear, determination of the area where upper requirements apply of Upper)	-
Cl 5.4.2 (Thickness)	-
Cl 5.4.3 (Tear strength)	-
Cl 5.4.4, Table 9 (Tensile properties- Tensile strength)	-
Cl 5.4.4, Table 9 (Tensile properties- Breaking Force)	-
Cl 5.4.4, Table 9 (Tensile properties-Modulus at 100 % elongation)	-
Cl 5.4.4, Table 9 (Tensile properties- Elongation at break)	-
Cl 5.4.5 (Flexing resistance)	-
Cl 5.4.6 (Water vapour permeability and coefficient)	-
Cl 5.4.7 (Resistance to hydrolysis)	-
Cl 5.5.2 (Lining- Tear strength)	-
Cl 5.5.3 (Lining- Abrasion resistance)	-
Cl 5.5.4 (Lining-Water vapour permeability and coefficient)	-
Cl 5.6.2 (Tear strength of tongue)	-
Cl 5.7.1 (Thickness of Insole, insock and footbed)	-
Cl 5.7.2 (Water permeability of insock)	-
Cl 5.7.3 (Water absorption and desorption of Insole, insock and footbed)	-
Cl 5.7.4.1 (Abrasion resistance of Insoles)	-
Cl 5.7.4.2 (Abrasion resistance of Insocks)	-
Cl 5.8.2.1 (Thickness of Outsole)	-
Cl 5.8.2.2 (Cleated area)	-
Cl 5.8.2.3 (Cleat height)	-
Cl 5.8.3 (Outsole- Tear strength)	-
Cl 5.8.4 (Outsole- Abrasion resistance)	-
Cl 5.8.5 (Outsole-Flexing resistance)	-
Cl 5.8.6 (Outsole-Resistance to hydrolysis)	-
Cl 5.8.7 (Interlayer bond strength)	-

Partial

Mech- Except Slip resistance Chem - Except PCP

IS 15298 : Part 3 (2024)

Personal Protective Equipment Part 3 Protective Footwear (ISO 20346 : 2021, MOD) (Third Revision)

For all class, design and size

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.2 (Design)	-
Cl 5.2.2 (" Height of upper ")	-
Cl 5.2.3 (Heel area)	-
Cl 5.3.1.1 (Construction of whole footwear)	-
Cl 5.3.1.2 (Upper/outsole bond strength)	-
Cl 5.3.2.1 (Toe protection - general)	-
Cl 5.3.2.2 (Internal length)	-
Cl 5.3.2.3 (Width of toecap flange)	-
Cl 5.3.2.4.1 (Corrosion resistance of Class I footwear and hybrid mounted footwear)	-
Cl 5.3.2.4.2 (Corrosion resistance of Class II and hybrid moulded footwear)	-
Cl 5.3.2.5 (Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-
Cl 5.3.2.6 (Impact resistance)	-
Cl 5.3.2.7 (Compression resistance)	-
Cl 5.3.3 (Leak proofness)	-
Cl 5.3.4 ("Specific ergonomic features ")	-
Cl 5.3.7 (Seam strength)	-
Cl 5.4.1.1 (Class I footwear, determination of the area where upper requirements apply of Upper)	-
Cl 5.4.1.2 (Hybrid footwear, determination of the area where upper requirements apply of Upper)	-
Cl 5.4.2 (Thickness)	-
Cl 5.4.3 (Tear strength)	-
Cl 5.4.4, Table 11 (Tensile properties- Tensile strength)	-
Cl 5.4.4, Table 11 (Tensile properties- Breaking Force)	-
Cl 5.4.4, Table 11 (Tensile properties-Modulus at 100 % elongation)	-
Cl 5.4.4, Table 11 (Tensile properties- Elongation at break)	-
Cl 5.4.6 (Water vapour permeability and coefficient)	-
Cl 5.4.7 (Resistance to hydrolysis)	-
Cl 5.5.2 (Lining- Tear strength)	-
Cl 5.5.3 (Lining- Abrasion resistance)	-
Cl 5.5.4 (Lining-Water vapour permeability and coefficient)	-
Cl 5.6.2 (Tear strength of tongue)	-
Cl 5.7.1 (Thickness of Insole, insock and footbed)	-
Cl 5.7.2 (Water permeability of insock)	-
Cl 5.7.3 (Water absorption and desorption of Insole, insock and footbed)	-
Cl 5.7.4.1 (Abrasion resistance of Insoles)	-
Cl 5.7.4.2 (Abrasion resistance of Insocks)	-
Cl 5.8.2.1 (Thickness of Outsole)	-
Cl 5.8.2.2 (Cleated area)	-
Cl 5.8.2.3 (Cleat height)	-
Cl 5.8.3 (Outsole- Tear strength)	-
Cl 5.8.4 (Outsole- Abrasion resistance)	-
Cl 5.8.5 (Outsole-Flexing resistance)	-
Cl 5.8.6 (Outsole-Resistance to hydrolysis)	-
Cl 5.8.7 (Interlayer bond strength)	-

Partial

Mech- Except Slip resistance Chem- Except PCP

IS 15914 (2011)

High tensile strength flat rolled steel plate (Up To 6 Mm), sheet and strip for the manufacture of welded gas cylinder - Specification

All grades

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 9 (Workmanship)	-
Cl. 10 (Mass)	-
Cl 10 (Length, Width & Thickness)	-
Cl. 7 Table 3 (Elongation)	-
Cl. 7 Table 3 (Yield Stress)	-
6.0 (CARBON)	-
6.0 (SULPHUR)	-
6.0 (PHOSPHORUS)	-
6.0 (MANGANESE)	-
6.0 (SILICON)	-
6.0 (NITROGEN)	-

Partial

IS 1855 (2022)

Stranded steel wire ropes for winding and man - Riding haulages in mines - Specification Third Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.6.1 and Table 1 of IS 1835 (Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.6.1 and Table 1 of IS 1835 (Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.6.1 and Table 1 of IS 1835 (Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.6.1 and Table 1 of IS 1835 (Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.6.1 and Table 1 of IS 1835 (Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.6.1 and Table 1 of IS 1835 (Chromium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.6.1 and Table 1 of IS 1835 (Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.6.1 and Table 1 of IS 1835 (Nickel- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Clause 4 (Rope size and tolerance)	-
Clause 6.4 (Lay)	-
Clause 7 (Galvanizing)	-
Clause 9 (Freedom from defects)	-

Partial

Mech: Declarations required - Nominal dia, Type of core, Rope grade

IS 15298 : Part 2 (2024)

Personal Protective Equipment Part 2 Safety Footwear (ISO 20345 : 2021, MOD) (Third Revision)

For all class, design and size

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.3.6, Table no 1 of IS 17011,(i) (Allergenic and carcinogenic disperse dyes)	-
Cl 5.3.6, Table no 1 of IS 17011 (ii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl 5.3.6, Table no 1 of IS 17011 (iii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl 5.3.6, Table no 1 of IS 17011 (iv) (Chromium (VI))	-
Cl 5.3.6, Table no 1 of IS 17011 (v) (Dimethyl fumarate (DMFU))	-
Cl 5.3.6, Table no1 of IS 17011 (vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl 5.3.6, Table no 1 of IS 17011 (vii) (Formaldehyde)	-
Cl 5.3.6, Table no 1 of IS 17011 (x) (pH)	-
Cl 5.3.6, Table no 1 of IS 17011 (xi) (Phthalates (each individual phthalate))	-
Cl 5.3.6, Table no 1 of IS 17011 (xii) (Nickel, on skin contact)	-
Cl 5.2 (Design)	-
Cl 5.2.2, Table 4 (" Height of upper ")	-
Cl 5.2.3 (Heel area)	-
Cl 5.3.1.1 (Construction of whole footwear)	-
Cl 5.3.1.2 (Upper/outsole bond strength)	-
Cl 5.3.2.1 (Toe protection - general)	-
Cl 5.3.2.2 (Internal length)	-
Cl 5.3.2.3 (Width of toecap flange)	-
Cl 5.3.2.4.1 (Corrosion resistance of Class I footwear and hybrid mounted footwear)	-
Cl 5.3.2.4.2 (Corrosion resistance of Class II and hybrid moulded footwear)	-
Cl 5.3.2.5 (Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-
Cl 5.3.2.6 (Impact resistance)	-
Cl 5.3.2.7 (Compression resistance)	-
Cl 5.3.3 (Leak proofness)	-
Cl 5.3.4 ("Specific ergonomic features ")	-
Cl 5.3.7 (Seam strength)	-
Cl 5.4.1.1 (Class I footwear, determination of the area where upper requirements apply of Upper)	-
Cl 5.4.1.2 (Hybrid footwear, determination of the area where upper requirements apply of Upper)	-
Cl 5.4.2 (Thickness)	-
Cl 5.4.3 (Tear strength)	-
Cl 5.4.4, Table 11 (Tensile properties- Tensile strength)	-
Cl 5.4.4, Table 11 (Tensile properties- Breaking Force)	-
Cl 5.4.4, Table 11 (Tensile properties-Modulus at 100 % elongation)	-
Cl 5.4.4, Table 11 (Tensile properties- Elongation at break)	-
Cl 5.4.5 (Flexing resistance)	-
Cl 5.4.6 (Water vapour permeability and coefficient)	-
Cl 5.4.7 (Resistance to hydrolysis)	-
Cl 5.5.2 (Lining- Tear strength)	-
Cl 5.5.3 (Lining- Abrasion resistance)	-
Cl 5.5.4 (Lining-Water vapour permeability and coefficient)	-
Cl 5.6.2, Table 14 (Tear strength of tongue)	-
Cl 5.7.1 (Thickness of Insole, insock and footbed)	-
Cl 5.7.2 (Water permeability of insock)	-
Cl 5.7.3 (Water absorption and desorption of Insole, insock and footbed)	-
Cl 5.7.4.1 (Abrasion resistance of Insoles)	-
Cl 5.7.4.2 (Abrasion resistance of Insocks)	-
Cl 5.8.2.1, Table 15 (Thickness of Outsole)	-
Cl 5.8.2.2 (Cleated area)	-
Cl 5.8.2.3 (Cleat height)	-
Cl 5.8.3 (Outsole- Tear strength)	-
Cl 5.8.4 (Outsole- Abrasion resistance)	-
Cl 5.8.5 (Outsole-Flexing resistance)	-
Cl 5.8.6 (Outsole-Resistance to hydrolysis)	-
Cl 5.8.7 (Interlayer bond strength)	-

Partial

Mech- Except Slip resistance Chem - Except PCP

IS 15644 (2006)

Safety of electric toys

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.15 (General Conditions)	-
5.15 (General Conditions)	-
5.15 (General Conditions)	-
7.0 (Marking and instructions)	-
9.3 ("Heating and Abnormal Operation (For All toys)")	-
9.4 ("Heating and Abnormal Operation (For All toys)")	-
9.5 ("Heating and Abnormal Operation (For All toys)")	-
9.6 (Heating and Abnormal Operation (For Toys incorporating motors))	-
9.7 (Heating and Abnormal Operation)	-
9.8 (Heating and Abnormal Operation)	-
9.8.1 (Heating and Abnormal Operation)	-
9.8.2 (Heating and Abnormal Operation)	-
10.0 (Electrical strength at operating temperature)	-
11.1 (Moisture resistance)	-
11.2 (Resistant to humidity)	-
12.0 (Electric strength at room temperature)	-
13.0 (Mechanical strength)	-
14.1 (Construction)	-
14.2 (Construction)	-
14.3 (Construction)	-
14.4 (Construction)	-
14.5 (Construction)	-
14.6 (Construction)	-
14.7 (Construction)	-
14.8 (Construction)	-
14.9 (Construction)	-
14.11 (Construction)	-
14.12 (Construction)	-
14.13 (Construction)	-
14.14 (Construction)	-
15.1 (Protection of cords and wires)	-
15.2 (Protection of cords and wires)	-
16.0 (Components)	-
17 Table-1 (Screws and connections)	-
17 Table-1 (Nominal daimeter of screws made of insulating material)	-
14.15 (Construction)	-
14.16, Table 2 (Construction)	-
18.0 (Clearance and creepage distance)	-
19.1 (Ball pressure test IEC 60695-10-2)	-
19.2.1 (Glow wire test IEC 60695-2-11)	-
19.2.2 (Needle flame test)	-
20.0 (Radiation, toxicity and similar hazards)	-
13 (Mechanical Strength)	-
5.15 (General Conditions)	-
5.15 (General Conditions)	-
5.15 (General Conditions)	-
5.15 (General Conditions)	-

Partial

Except toys having LASER and light emitting diodes. Test facilities for toys above size of 34"x22"x22" is not available.

IS 5557 : Part 2 (2018)

All rubber gum boots and ankle boots: Part 2 occupational purposes

For all Type and Variety

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (visual)	-
7.1.1 (Tear strength)	-
7.1.2 (Abrasion resistance)	-
7.5.1 (Tensile)	-
7.5.3 (Upper flexing)	-
7.6.1 (Out sole thickness)	-
7.6.3 (out sole abrasion)	-
7.6.4 (out sole flexing)	-
7.6.5 (Interlayer bond strength)	-
7.7.1 (Insock thickness)	-
7.7.2 (Insock abrasion)	-
8.2 (Leak proofness)	-
8.1 (Hot contact)	-
8.3 (Height of upper)	-
8.4 (Adhesion test)	-
9.1 (ALLERIGIC DISPERSE DYES)	-
9.2 (Carcinogenic Disperse dyes)	-
9.3 (Phthalate)	-
7.3 (sulphur test)	-

Partial

Mech- Except Degradation test(Cl 8.5) Chem- Except Allergenic and carcinogenic dyes, Poly chlorophenols, Organotin compounds

IS 17043 : Part 2 (2024)

Shoes: Shoes for General Purpose

For all type

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.4 S.No (1), i (Bond strength, N/mm, Min Upper to outsole, N/mm, Min)	-
Cl-5.4, S.No (1), ii (Inter layer bond strength,= N/mm, Min Midsole to outsole, N/mm, Min)	-
Cl-5.4, S.No (1), vi (Attachment strength of strap and buckle/D-ring N)	-
Cl-5.4, S.No (1), vii (Attachment strength of strap and velcro , N, Min)	-
Cl-5.4, S.No (1), xi (Seam strength, N/mm, Min)	-
Cl-5.4, S.No (1), xiii (Abrasion resistance (volume loss), mm3)	-
Cl-5.4, S.No (1), xvi (Hydrolysis resistance,(4) cut growth at 150 000 flexes, mm, Max)	-
Cl-6.1.1 S.No (1), v (Water vapour permeability,mg/cm2 /h, Min Water vapour coefficient,mg/cm2 , Min)	-
Cl-6.1.1, S.No (1), vii (Abrasion resistance)	-
Cl-6.1.3, S.No (1), v (Water vapour permeability (WVP), mg/cm2 /h, Min)	-
Cl-6.1.3, S.No (1), vii (Abrasion resistance)	-
Cl-5.4, S.No (1), xiv (Chemical requirements(3))	-
Cl-5.4, S.No (1), xv (Lead content (as Pb) ppm, Max)	-

Partial

Mech- Except Water proofness on complete shoe table 1, Slip resistance table 1, Strength of eyelet attachment table 1, Heel pull off strength as per Table 1, Top piece attachment strength table 1, Whole shoe topline strength, table 1, Flexing resistance table 2, Colour fastness to light table 3, Colour fastness to rubbing table 2, Flexing resistance table 4, Flexing index Table 7, Counter stiffener as per Table 14, Peel strength & Shear strength as per Table 15, Lace tag strength of Table 17, Fatigue resistance table 18 zipper, Security of puller attachment strength table 18 zipper and End attachment strength table 18 zipper Chem - Except Allergenic and carcinogenic dyes, Organotin compounds, Polychlorophenols

IS 14543 (2024)

Packaged Drinking Water Other than Packaged Natural Mineral Water Specification Third Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.3, Table-1 (i) (Colour, true colour units, Max)	-
Cl-5.3, Table-1 (ii) (Odour)	-
Cl-5.3, Table-1 (iii) (Taste)	-
Cl-5.3, Table-1 (iv) (Turbidity, nephelometric turbidity unit (NTU), Max)	-
Cl-5.3, Table-1 (v) (Total dissolved solids, mg/l, Max)	-
Cl-5.3, Table-1 (vi) (pH)	-
Cl-5.3, Table-2 (i) (Barium (as Ba))	-
Cl-5.3, Table-2 (ii) (Copper (as Cu))	-
Cl-5.3, Table-2 (iii) (Iron (as Fe))	-
Cl-5.3, Table-2 (iv) (Manganese (as Mn))	-
Cl-5.3, Table-2 (v) (Nitrate (as NO3 ))	-
Cl-5.3, Table-2 (vi) (Nitrite (as NO2 ))	-
Cl-5.3, Table-2 (vii) (Fluoride (as F))	-
Cl-5.3, Table-2 (viii) (Zinc (as Zn))	-
Cl-5.3, Table-2 (ix) (Silver (as Ag))	-
Cl-5.3, Table-2 (x) (Aluminium (as A1))	-
Cl-5.3, Table-2 (xi) (Chloride (as Cl))	-
Cl-5.3, Table-2 (xii) (Selenium (as Se))	-
Cl-5.3, Table-2 (xiii) (Sulphate (as SO4 ))	-
Cl-5.3, Table-2 (xiv) (Alkalinity (as HCO3 ))	-
Cl-5.3, Table-2 (xv) (Calcium (as Ca))	-
Cl-5.3, Table-2 (xvi) (Magnesium (as Mg))	-
Cl-5.3, Table-2 (xvii) (Sodium (as Na))	-
Cl-5.3, Table-2 (xviii) (Residual free chlorine)	-
Cl-5.3, Table-2 (xix) (Phenolic compounds (as C6H5OH))	-
Cl-5.3, Table-2 (xx) (Mineral oil)	-
Cl-5.3, Table-2 (xxi) (Anionic surface active agents)	-
Cl-5.3, Table-2 (xxii) (Sulphide)	-
Cl-5.3, Table-2 (xxiii) (Antimony (as Sb))	-
Cl-5.3, Table-2 (xxiv) (Borates (as B))	-
Cl-5.3, Table-2 (xxv) (Bromates (as BrO3 ))	-
Cl-5.3, Table-3 (i) (Mercury (as Hg))	-
Cl-5.3, Table-3 (ii) (Cadmium (as Cd))	-
Cl-5.3, Table-3 (iii) (Arsenic (as As))	-
Cl-5.3, Table-3 (v) (Lead (as Pb))	-
Cl-5.3, Table-3 (vi) (Chromium (as Cr))	-
Cl-5.3, Table-3 (vii) (Nickel (as Ni))	-
Cl-5.3, Table-3 (viii) (Polychlorinated biphenyl (PCB))	-
Cl-5.3, Table-3 (ix) (Polynuclear aromatic hydrocarbons)	-
Cl-5.2.1 (Escherichia coli or thermotolerant bacteria)	-
Cl-5.2.2 (Coliform)	-
Cl-5.2.3 (Staphylococcus aureus)	-
Cl-5.2.3 (Faecal streptococci)	-
Cl-5.2.4 (Sulphite Reducing Anaerobes)	-
Cl-5.2.5 (Pseudomonas Aeruginosa)	-
Cl-5.2.6 (Aerobic Microbial Count @ 37 deg C)	-
5.2.6 (Aerobic Microbial Count @ 20 to 22 deg C)	-
Cl-5.2.7 (Yeast and mould)	-
Cl-5.2.8 (Salmonella)	-
Cl-5.2.8 (shigella)	-
Cl-5.2.9 (Vibrio cholera)	-
Cl-5.2.9 (V.parahaemolyticus)	-
Cl-5.4 (ii) (Total pesticide residue)	-
5.4 i) (Dieldrin)	-
5.4 i) (Aldrin)	-
5.4 i) (Malathion)	-
5.4, i) ("oxygen analogue of Malathion (Malaoxon)")	-
5.4 i) (Methyl Paraoxon)	-
5.4 i) (Methyl Parathion)	-
5.4 i) (Atrazine)	-
5.4 i) (Alachlor)	-
5.4 i) (Isoproturon)	-
5.4 i) (Butachlor)	-
5.4 i) (Phorate sulphone)	-
5.4 i) (Phorate sulphoxide)	-
5.4 i) (Phorate)	-
5.4 i) (Chlorpyrifos)	-
5.4 i) (Ethion)	-
5.4 i) (Monocrotophos)	-
5.4 i) (Endosulfan Sulphate)	-
5.4 i) (2,4-D)	-
5.4 i) (beta-Endosulfan)	-
5.4 i) (alpha-Endosulfan)	-
5.4 i) (Delta-HCH)	-
5.4 i) (beta-HCH)	-
5.4 i) (alpha-HCH)	-
5.4 i) (Gamma-HCH (Lindane))	-
5.4 i) (p,p DDD)	-
5.4 i) (o,p DDD)	-
5.4 i) (p,p DDE)	-
5.4, i) (o,p DDE)	-
5.4 i) (p,p DDT)	-
5.4 i) (o,p DDT)	-
Cl-5.3, Table-3 (x) (Uranium)	-
5.3 (Appearance)	-

Partial

Excluding Cyanide, Radio Active Elements. For testing of Pesticide Residues please indicate accordingly

IS 15041 (2001)

Textiles – Flat woven webbing slings made of man-made fibres for general services

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1 (REQUIREMENTS :-Webbing)	-
4.1.2.1 (Weaving)	-
4.1.3 (Width)	-
4.2.2 (Sewing of Slings)	-
4.2.3 (Sewing of Slings)	-
4.2.3.1 (Sewing of Slings)	-
4.2.4 (Sewing of Slings)	-
4.2.4.1 (Sewing of Slings)	-
4.2.5 (Sewing of Slings)	-
4.3.1,Fig. 10 (Soft Eyes)	-
4.4.1 (End Fittings :General)	-
4.4.3 (End Fittings :-Finish)	-

Partial

Excluding cl 4.1.1 Materials, Cl 4.1.5 Dyeing, Cl 4.1.6 Other Treatments, Afiertreatments or Coverings, Cl 4.4.2 Materials, Cl 4.4.5 Proof Testing, Cl 4.5 Working Load Limit, Cl 4.6 Maximum Safe Working Load and Cl 4.7 Safety Factor

IS 2573 (2023)

LEATHER GAUNTLETS AND MITTENS SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 Cl. 5.2.1, Sl No (i) (Solvent exractable substances, percent by mass)	-
Table 1 Cl. 5.2.1, Sl No (ii) (Chromium content (as Cr2O3), percent by mass)	-
Table 1 Cl. 5.2.1, Sl No (iii) (pH of aqueous extract)	-
4.1 (Type)	-
4.2 (Length(L))	-
5.1 (Dimensions(fig 1 to fig 3))	-
5.2.1(a) (Thickness of Leather and Flesh split)	-
5.2.1(Table 1, serial vi) (Abrasion resistance, Dry condition)	-
5.2.1(Table 1, serial vi) (Abrasion resistance, Wet condition)	-
5.2.2(Table 2) (Thread Length, Min)	-
5.2.2(Table2) (Single thread breaking load, Min)	-
5.3.1.2 (Construction(for Type 1))	-
5.3.1.3 (Construction(for Type 1))	-
5.3.1.4 (Construction(for Type 1))	-
5.3.1.5 (Construction(for Type 1))	-
5.3.1.6 (Construction(for Type 1))	-
5.3.1.7 (Construction(for Type 1))	-
5.3.1.8 (Construction(for Type 1))	-
5.3.1.9 (Construction(for Type 1))	-
5.3.1.10 (Construction(for Type 1))	-
5.3.1.11 (Workmanship and finish)	-
5.3.2.2 (Construction(for Type 2))	-
5.3.2.3 (Construction(for Type 2))	-
5.3.2.4 (Construction(for Type 2))	-
5.3.2.5 (Construction(for Type 2))	-
5.3.2.6 (Construction(for Type 2))	-
5.3.2.7 (Construction(for Type 2))	-
5.3.2.8 (Construction(for Type 2))	-
5.3.2.9 (Construction(for Type 2))	-
5.3.2.10 (Construction(for Type 2))	-
5.3.2.11 (Construction(for Type 2))	-
5.3.2.12 (Workmanship and finish)	-
5.3.3.2 (Construction(for Type 3))	-
5.3.3.3 (Construction(for Type 3))	-
5.3.3.4 (Construction(for Type 3))	-
5.3.3.5 (Construction(for Type 3))	-
5.3.3.6 (Construction(for Type 3))	-
5.3.3.7 (Construction(for Type 3))	-
5.3.3.8 (Construction(for Type 3))	-
5.3.3.9 (Construction(for Type 3))	-
5.3.3.10 (Construction(for Type 3))	-
5.3.3.11 (Construction(for Type 3))	-
5.3.3.12 (Construction(for Type 3))	-
5.3.3.13 (Construction(for Type 3))	-
5.3.3.14 (Construction(for Type 3))	-
5.3.3.15 (Workmanship and finish)	-

Partial

Facility not available for shrinkage temperature test of RM, Length

IS 16993 (2018)

Microfine Ordinary Portland Cement ” Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 -Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5 -Table - 1 ii (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
5 -Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5 -Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5 -Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5 -Table - 1 vi (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
5 -Table - 1 vii (Chloride content - Cl 4.13 of IS 4032:1985)	-
5 -Table - 1 viii ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
5 -Table - 1 ix ( (Additional requirements) for microfine sulphate resisting Portland cement: a) Tricalcium aluminate (C3A) - Cl 4 of IS 4032:1985)	-
Cl.5 - Table No 1 - Sl. No.-ix, a (Tricalcium aluminate (C3A) - IS 4032)	-
Cl.5 - Table No 1 - Sl. No.-ix, b (Tetracalcium alumino ferrite phase plus twice the tricalcium aluminate (C2AF + 2C2A) - IS 4032)	-
6 and Table 2 iii a (Setting Time Initial)	-
6 and Table 2 iii b (Setting Time Final)	-
6 and Table 2 iv (Bleeding test at 3 h from the time of mixing)	-

Partial

Except Fineness and Particle size

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

For all type

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.8 Table-1 S.No 1, (i) (Amendment No-1) (Bond strength , N/mm, Min)	-
Cl.8 Table-1 S.No 1, (viii) (Amendment No-1) (Hydrolysis resistance)	-
Cl.8 Table-1 S.No 1, (x) (Amendment No-1) (Inter layer bond strength)	-
Cl.8 Table-1 S.No 1, (xii) (Amendment No-1) (Abrasion resistance, (volume loss) mm3 , Max)	-
Cl.8 Table-1 S.No 1, (xiii) (Amendment No-1) ("Flexing resistance (Belt method or Bennewart flex method)")	-
Cl.9 Table-2 S.No 1, (i) a (Amendment No-1) (Tear strength for other than moulded upper material)	-
Cl.9 Table-3 S.No 1, (i) (Amendment No-1) (Tear strength, N, Min)	-
Cl.9 Table-3 S.No 1, (ii) (Amendment No-1) ("Abrasion resistance (a) dry condition (b) wet condition")	-
Cl.9 Table-4 S.No 1, (ii) (Amendment No-1) ("Abrasion resistance (a) dry condition (b) wet condition")	-
Cl.9 Table-5 S.No 1, (ii) (Amendment No-1) (Density, g/cm3 , Min)	-
Cl.9 Table-4 S.No 1, (i) (Amendment No-1) (Tear strength, N, Min)	-
Cl.9 Table-6 S.No 1, (i) (Amendment No-1) ("Density, g/cm3 , Min (a)-Cellular, (b) Solid ")	-
Cl.8 Table-1 S.No 1, (xv) (Amendment No-1) (Lead content (as Pb)7 ppm)	-
Cl. No.8.6.1,Table 1 of IS 17011(x) (pH)	-
Cl. No.8.6.1,Table 1 of IS 17011(ii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl. No.8.6.1,Table 1 of IS 17011(iv) (Chromium (VI))	-
Cl. No.8.6.1,Table 1 of IS 17011(v) (Dimethyl fumarate (DMFU))	-
Cl. No.8.6.1,Table 1 of IS 17011(vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl. No.8.6.1,Table 1 of IS 17011(xi) (Phthalates (each individual phthalate))	-
Cl. No.8.6.1,Table 1 of IS 17011(xii) (Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-

Partial

Mech- Except Flexing endurance, Toe post & toe ring attachment strength, Strap to outsole strength, Heel pull off strength, Slip Resistance (Table 1) and Abrasion resistance as per table 5, Type to be declared Chem- Polychlorophenol

IS 7454 (1991)

Rehabilitation equipment - Wheelchairs, folding, adult size - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1 Table 1 (Overall Length)	-
Cl. 5.1 Table 1 (Overall Width, Open)	-
Cl. 5.1 Table 1 (Overall Width, Folded)	-
Cl. 5.1 Table 1 (Overall height)	-
Cl. 5.1 Table 1 (Scat height from floor at the fron)	-
Cl. 5.1 Table 1 (Slope of the seat)	-
Cl. 5.1 Table 1 (Slope of backrest with respect to floor)	-
Cl. 5.1 Table 1 (Distance between seat and footrest)	-
Cl. 5.1 Table 1 (Armrest height from seat)	-
Cl. 5.1 Table 1 (Scat depth)	-
Cl. 5.1 Table 1 (Clearance of footrest from floor)	-
Cl. 5.1 Table 1 (Clearance of frame from floor)	-
Cl. 5.1 Table 1 (Wheel diameter)	-
Cl. 5.1 Table 1 (Weight of the wheel chair ( basic model ))	-
Cl. 7.1 (Backrest and Seat)	-
Cl.7.2 (Frame)	-
Cl.7.3 (Footrests and Supports)	-
Cl.7.4 ( Armrests)	-
Cl.7.5 (Hand Rims)	-
Cl.7.6 (Brakes)	-
Cl.7.7 (Castors)	-
Cl.7.8 (Wheels)	-
Cl.7.9 (Clothing Guards)	-
Cl.7.10 (Folding Mechanism)	-
Cl.7.11 (Lubrication)	-
Cl. 8 (Finish)	-
Cl. 9.1 (Test for Wheeling)	-
Cl. 9.2 (Hazard Running Test)	-
Cl. 9.3 (Load Test)	-
Cl. 9.4 (Test for Folding)	-

Partial

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1,7.1.1 IS 12235 (Part 1) Table 2 (Outside Diameter at any point)	-
7.1.2 IS 12235 (Part 1) Table 2 (Wall Thickness )	-
9.1 (Visual Appearance)	-
9.2 IS 12235 (Part 3) (Opacity)	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2) (Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-
9.5 IS 12235(Part 2) (Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-
9.6 IS 12235(Part 14) (Density)	-
10.3 IS 4985 Table 4 (Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-
10.5 IS 12235(Part 13) (Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-
10.4 IS 12235(Part 19) (Flattening Test)	-

Partial

Excluding Cl 6.3.2 Verification of the Malfunction Temperature, Cl 6.3.1 Chlorine Content, Cl 9.3 Effect on Water, Cl 10.1 Hydrostatic Characteristics and Cl 10.2 Thermal Stability by Hydrostatic Testing.

IS 18384 (2023)

Hot-Rolled Steel Strip, Sheet and Plates for Welded Steel Pipe for Pipeline Transportation Systems ï¿½ Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.8.1, 8.2, 8.4, table 2, table 3 (Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (Chromium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (Nickel- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (Molybdenum- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (CEPcm- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.8.1, 8.2, 8.4, table 2, table 3 (CEIIW - Relevant parts of IS 228 or any other established chemical/instrumental method)	-

Partial

Excluding DWT Test (For PSL 2 Steel Grade) and Laminar Imperfection in Hot-rolled Plates Chem - Except Nb and V

IS 1912 (2023)

Textiles Country jute twine - Specification (third revision)

For all varieties except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2 (Yarn)	-
5.3 (Twine)	-
5.4 (Skein)	-
5.6 (Moisture Regain)	-
6.1 ("TABLE 1 ( Linear Density, Ply , Twist, Breaking Load ) ")	-

Partial

Excluding Fibre Identification

IS 9550 (2001)

Bright steel bars - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Mechancial Properties)	-
8.1 and 8.2 (Dimensions and Tolerances, mm)	-

Partial

IS 10702 (2023)

Hawai Chappal-Specification

For all type

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.No. 5.2 (lead content)	-
Cl.4.4 - Table No 1 - Sl. No.-viii ("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-
Clause 4.1 - 4.1.1 (Bottom Material)	-
Clause 4.1 - 4.1.2 (Strap Material)	-
Clause 4.1 - 4.1.3 (Material)	-
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1) (Compression set at constant stress)	-
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1) (Split tear strength)	-
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1) ("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1) (Abrasion resistance at applied force)	-
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1) (Flexing resistance: Maximum cut growth,)	-
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1) (Hydrolysis resistance:Maximum cut growth)	-
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1) ("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1) (Inter layer bond strength)	-
Cl. No.5.1,Table no.1 of IS 17011(i) (Allergenic and carcinogenic disperse dyes)	-
Cl. No.5.1,Table no.1 of IS 17011(ii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl. No.5.1,Table no.1 of IS 17011(iii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl. No.5.1,Table no.1 of IS 17011(iv) (Chromium (VI))	-
Cl. No.5.1,Table no.1 of IS 17011(v) (Dimethyl fumarate (DMFU))	-
Cl. No.5.1,Table no.1 of IS 17011(vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl. No.5.1,Table no.1 of IS 17011(vii) (Formaldehyde)	-
Cl. No.5.1,Table no.1 of IS 17011(viii) (Organotin compounds)	-
Cl. No.5.1,Table no.1 of IS 17011(x) (pH)	-
Cl. No.5.1,Table no.1 of IS 17011(xi) (Phthalates (each individual phthalate))	-
Cl. No.5.1,Table no.1 of IS 17011(xii) (Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-

Partial

Mech- Complete except Toe post attachment strength as per Table 3 and Attachment strength of rear strap as per Table 3. Chem- Complete except Organotin, Allergenic dyes and PCPs (if applicable) Declaration required - Type to be mentioned, Material declaration required for Innocuousness test.

IS 16714 (2018)

Ground granulated blast furnace slag for use in cement, mortar and concrete - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 and Table 2 i (Fineness IS 4031 (Part 2))	-
6 and Table 2 ii a (Slag activity index -7 days)	-
6 and Table 2 ii b (Slag activity index -28 days)	-
Clause 5.1 (Manganese oxide (MnO))	-
Clause 5.1 (Magnesium oxide (MgO))	-
Clause 5.1 (Sulphide sulphur (S))	-
Clause 5.1 (Sulphate (as SO3),)	-
Clause 5.1 (Insoluble residue)	-
Clause 5.1 (Chloride content)	-
Clause 5.1 (Loss on ignition)	-
Clause 5.1 ((CaO+MgO+1/3AlO3)/( SiO2 +2/3 AlO3))	-
Clause 5.1 ((CaO+MgO+Al2O3)/ SiO2)	-
Clause 5.1 ((CaO+CaS+1/2 MgO+Al2O3)/ (SiO2+ MnO))	-

Partial

Except glass content

IS 18573 (2024)

Cold formed welded carbon steel square and rectangular hollow sections for mechanical, general engineering and decorative purposes ï¿½ Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause.4.0 (Sulphur)	-
Clause.4.0 (Phosphorus)	-
Clause.6.0 (Workmanship)	-
Clause.10.0 (Dimensions and properties)	-
Clause.11.0 (Outside Dimension)	-
Clause.11.0 (Thickness)	-
Clause.11.0 (Concavity and Convexity)	-
Clause.11.0 (Squareness of Sides)	-
Clause.11.0 (Straightness and twist)	-
Clause.12.0 (Dimension Tolerances)	-
Clause.13.0 (Surface Protection)	-
Clause.15.0 (Tensile test)	-

Partial

IS 15500 : PART 7 (2021)

Deepwell Handpumps, Components and Secial Tools — Specification Part 7 Handpumps

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 ("The constructional details of different components covered in this part shall be as given in Fig. 7.1 to 7.18.")	-
2.2 (" The material and dimensions shall meet the related prerequisites given in 4 and 5 of Part 1.")	-
3 (TESTING)	-

Partial

Excluding Critical dimesnions

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- erol@bis.gov.in

Scope List