BIS - LIMS (Laboratory Information Management System)

IDMA LABORATORIES LIMITED

PLOT NO. 391 INDUSTRIAL AREA PHASE 1, PANCHKULA, Panchkula, Haryana, 134113

9888002607 testing@idmagroup.co.in

Scope List

Reset

464 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 13422 (2024)

Single-use Sterile Rubber Surgical Gloves ï¿½ Specification (First Revision)

294000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Materials)	-	240000	Rs. 240000/- for Conformity of Gloves to Relevant part of ISO 10993 series (Clause 5.4) 1) Cytotoxicity INR 50000 2) Skin Sensitization INR 120000 3) Skin Irritation INR 70000
Cl-6(Sampling and selection of test pieces)	-	0	Inspection level and AQL as per Table 1 not applicable as Testing will be carried out on the Samples as received
Cl-7.1(Dimensions)	-	6000	1) Width (H) INR 2000 2) Minimum Length (L) INR 2000 3) Minimum Thickness INR 2000
Cl-7.2(Watertightness)	-	8000	Testing charges 1) Rs. 39000/- Excluding Sterility (Clause 7.4) and Conformity tests (Clause 5.4) 2. Rs.15000/- for Sterility Test only (Clause 7.4) 3.Rs. 240000/- for Conformity of Gloves to Relevant part of ISO 10993 series (Clause 5.4)
Cl-7.3(Tensile properties)	-	0	As mentioned below
Cl-7.3.2(Force at break and elongation at break before accelerated ageing)	-	5000	Testing Charges 1) Force at break before accelerated ageing INR 2500 2) Elongation at break before accelerated ageing INR 2500
Cl-7.3.3(Force at break and elongation at break after accelerated ageing)	-	10000	Testing Charges 1) Minimum force at break after accelerated ageing INR 5000 2) Minimum Elongation at break after accelerated ageing INR 5000
Cl-7.3.4(Force required to produce 300 % elongation)	-	3000	Testing Charges 1) Force require to produce 300% Elongation before accelerated ageing INR 3000
Cl-7.4(Sterility)	-	15000	No Test Method Prescribed. The Charges are given in case the Sterility is performed as per respective IP. Testing Charges Rs.15000/- for Sterility Test only (Clause 7.4)
Cl-9(Marking.)	-	0	Testing charges for 1) Design as per clause 4.3 is INR 2000 2) Finish as per clause 4.4 is INR 5000
Cl-7.3.1(General)	-	0	-

31 Dec, 2026

-
-

IS 5405 (2025)

Disposable Sanitary Napkin/Panty Liner/Maternity Pad/Period Panty - Specification ( Third Revision )

Sanitary Napkin, Panty liner, Maternity Pad, Period panty

261600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Cover/Top sheet)	-	800	Testing charges are Rs. 800/- for Cl. no. 3.1 Cover / Top sheet, 3.2 Absorbent core & 3.3 Barrier or Bottom sheet.
3.2(Absorbent core)	-	0	Testing charges already mentioned above at cl. no. 3.1 Cover / Top sheet i.e. Rs. 800/-.
3.3(Barrier or bottom sheet)	-	0	Testing charges already mentioned above at cl. no. 3.1 Cover / Top sheet i.e. Rs. 800/-.
4.1(Types)	-	800	Testing charges are 800/- for cl. 4.1 & 4.2
4.2(shapes)	-	0	Testing charges are 800/- for cl. 4.1 & 4.2 already mentioned above.
5(Sizes)	-	800	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1.
Cl. 5 Table-1(Type)	-	0	Total testing charges are Rs. 2,61,600/- including Bio compatibility evaluation - Cytotoxicity, Irritation & Skin sensitization (as per cl. no. 7.4) & (excluding Compostability as per cl. 7.6).
Cl. 5 Table-1(Size class)	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
Cl. 5 Table-1(Length (Absorbent core only))	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
Cl. 5 Table-1(Width (Absorbent core only))	-	0	Testing charges are 800/- for Size, Size class, Length (Absorbent core only, Width (Absorbent core only as per cl. 5 Table - 1 already mentioned above.
6.1(Manufacture, workmanship and finish)	-	500	Testing charges are 500/- for cl. 6.1 & 6.2.
6.2(Manufacture, workmanship and finish)	-	0	Testing charges are 500/- for cl. 6.1 & 6.2 already mentioned above.
7.1(pH value (IS 1390))	-	1000	Testing charges are Rs. 21,600/- excluding Bio compatibility evaluation - Cytotoxicity, Irritation & Skin sensitization (as per cl. no. 7.4) &excluding Compostability as per cl. 7.6).
7.2(Ability to withstand Pressure after absorption)	-	1200	Testing charges are 1200/- for cl. Ability to Withstand Pressure after Absorption & Ability to Withstand Pressure after Absorption - leakage.
7.2(Ability to withstand Pressure after absorption - Leakage)	-	0	Testing charges are 1200/- for cl. Ability to Withstand Pressure after Absorption & Ability to Withstand Pressure after Absorption - leakage already mentioned above.
7.3.1(Total Viable count)	-	3000	-
7.3.2(Staphylococcus aureus)	-	3000	-
7.4(Biocompatibility evaluation - Cytotoxicity (IS/ISO 10993 P-5))	-	50000	-
7.4(Biocompatibility evaluation - Irritation (IS 17932 P-7))	-	70000	-
7.4(Biocompatibility evaluation - skin Sensitization (Optional) (IS 17932 P-6))	-	120000	-
7.5(Phthalate test)	-	8000	-
7.7(Anti bacterial activity value (Optional) (IS/ISO 20743))	-	2500	-
7.6(Compostability (Optional) (IS/ISO 17088))	-	0	Clause no. 7.6 Compostability (Optional) test is applied for Exclusion as the test facilities are currently not available.

31 Dec, 2026

-
Included w.e.f.05.03.2025 Exclusion Cl 7.6 (Compostability (Optional) (IS/ISO 17088)

IS 15219 (2024)

Aluminium phosphide powder formulation - Specification (first revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1(Description - IS 15219:2002)	-	1000		-
3.3.1(Aluminium Phosphide Content - IS 6438:1980)	-	6000		-

31 Dec, 2026

-
Included w.e.f.24.04.2025

IS 9356 (2024)

Butachlor emulsifiable concentrate (EC) - Specification (first revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description - IS 9356 : 2024)	-	500	-
3.2.2(Cold Test - IS 6940 : 1982)	-	1000	-
3.2.3(Flash Point - IS 6940 : 1982)	-	1000	-
3.2.4(Emulsion Test - IS 6940 : 1982)	-	1500	-
3.3.1(Butachlor Content - IS 9355 : 2024)	-	3000	-
3.3.2(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-
3.3.2(Alkalinity (as NaOH) - IS 6940 : 1982)	-	0	Testing charges i.e. Rs. 1500/- already mentioned above at clause no. 3.3.2 (Acidity (as H2SO4).

31 Dec, 2026

-
Included w.e.f 09.04.2025

IS 9355 (2024)

Butachlor, Technical - Specification (First Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description - IS 9355 : 2024)	-	500	-
3.2 & 7, Table - 1 (i)(Butachlor Content - IS 9355 : 2024)	-	3000	-
3.2 & 7, Table - 1 (ii)(Moisture Content - IS 6940 : 1982)	-	2000	-
3.2 & 7, Table - 1 (iii)(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-
3.2 & 7, Table - 1 (iv)(Material insoluble in Acetone - IS 6940 : 1982)	-	1500	-

31 Dec, 2026

-
Included w.e.f 09.04.2025

IS 8074 (2024)

Monocrotophos, Soluble Concentrate (SL) - Specification (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1(Description - IS 8074 : 2024)	-	500	-
3.2.2(Cold Test - IS 6940 : 1982)	-	1000	-
3.2.3(Flash Point - IS 6940 : 1982)	-	1000	-
3.3.1(Monocrotophos Content - IS 8025 : 2024)	-	3500	-
3.3.2(Free Aceto - Acetic Acid Monomethyl - Amide (MMA) content - IS 8025 : 2024)	-	3000	-
3.3.3(Acidity ( as H2SO4) - IS 6940 : 1982)	-	1000	-

31 Dec, 2026

-
Included w.e.f. 24.04.2025

IS 8025 (2024)

Monocrotophos, Technical - Specification (Third Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description - IS 8025 : 2024)	-	1000	-
3.2 & 7 Table - 1 (i)(Monocrotophos Content - IS 8025 : 2024)	-	3500	-
3.2 & 7 Table - 1 (ii)(Free Acetic Acid Mono - methylamide (MMA) - IS 8025 : 2024)	-	3000	-
3.2 & 7 Table - 1 (iii)(Acidity (as H2SO4) - IS 6940 : 1982)	-	1500	-

31 Dec, 2026

-
Included w.e.f.24.04.2025

IS 3205 (2024)

Precipitated Barium Carbonate, Technical - Specification (Second Revision)

Grade 1 & Grade 2

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description - IS 3205:2024)	-	500	-
4.2 Table(i)(Barium (as Ba) - IS 3205: 2024)	-	1500	-
4.2 Table(ii)(Carbonate (as CO3) - IS 3205: 2024)	-	2000	-
4.2 Table(iii)(Moisture - IS 3205: 2024)	-	2000	-
4.2 Table(iv)(Matter insoluble in hydrochloric acid - IS 3205: 2024)	-	1500	-
4.2 Table(v)(Free alkali - IS 3205: 2024)	-	1500	-
4.2 Table(vi)(Water soluble sulphide (as BaS) - IS 3205: 2024)	-	1500	-
4.2 Table(vii)(Total sulphur (as SO4) - IS 3205: 2024)	-	1500	-
4.2 Table(viii)(Alkali and other metal sulphates (as BaSO4) - IS 3205: 2024)	-	1500	-
4.2 Table(ix)(Sodium oxides (as Na2O)- IS 3205: 2024)	-	1500	-
4.2 Table(x)(Iron (as Fe2O3)- IS 3205: 2024)	-	1500	-
4.2 Table(xi)(Tap density- IS 3205: 2024)	-	1000	-
4.2 Table(xii)(Residue retained on 63 micron IS sieve- IS 3205: 2024)	-	1500	-
4.2 Tablexii(i)(Reaction efficiency (after 45 min)- IS 3205: 2024)	-	1000	-

31 Dec, 2026

-
Included w.e.f.24.04.2025

IS 5405 (2019)

Sanitary napkins – Specification (second revision)

260200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(SIZES, Regular )	-	1500	Rs. 1550/- for dimensions of all sizes
6.0(Manufacture, workmanship & finish)	-	500	Rs. 20,200/- Excluding Biocompatibility Evaluation – Cytotoxicity, Irritation & Skin Sensitization (as per cl. no. 7.4) & Biodegradability (Clause 7.5).
Cl 7.1(pH Value, IS 1390 (cold method) for all sizes)	-	700	OK
Cl 7.2(Ability to Withstand Pressure after Absorption, for all sizes, Annex B)	-	1500	OK
Cl 7.3.1(Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-	3000	OK
Cl7.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-	3000	OK
Cl 7.4(Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization, IS/ISO 10993 Part 5 and IS/ISO 10993 Part 10)	-	240000	Rs. 2,60,200/- Including Biocompatibility Evaluation – Cytotoxicity, Irritation & Skin Sensitization (as per cl. no. 7.4). Excluding Biodegradability (Clause 7.5)
Cl 7.5(Biodegradability and Compostability (Optional), IS/ISO 17088.)	-	0	Marked for exclusion
7.6(Pthalate test)	-	10000	Testing charges for Clause no. 7.6, Pthalate test are Rs. 8500/- for all the 7 parameters as listed below. i) DBP ii)BBP iii) DEHP iv) DNOP v) DINP vi) DIDP vii) DIBP
Cl 5(SIZES, Regular )	-	0	As above
6.0(Manufacture, workmanship & finish)	-	0	As above
Cl 7.1(pH Value, IS 1390 (cold method) for all sizes)	-	0	As above
Cl 7.2(Ability to Withstand Pressure after Absorption, for all sizes, Annex B)	-	0	As above
Cl 7.3.1(Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-	0	As above
Cl7.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-	0	As above
Cl 7.4(Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization, IS/ISO 10993 Part 5 and IS/ISO 10993 Part 10)	-	0	As above
7.6(Pthalate test)	-	0	As above

31 Dec, 2026

-
-

IS 10813 (2022)

SOAP JELLY FOR LAUNDRY PURPOSES â SPECIFICATION

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1("Description ( IS 10813: 2022 )")	-	1000	-
4.1("Description ( IS 10813: 2022 )")	-	0	Testing charges already mentioned above
4.2("Solubility ( IS 10813: 2022 )")	-	1000	-
4.3("Storage ( IS 10813: 2022 )")	-	1500	-
4.4("Odour ( IS 10813: 2022 )")	-	1000	-
4.5("Stability at 0°C ( IS 10813: 2022 )")	-	2000	-
4.6 Table 1 (i)("Total fatty matter ( IS 286: 2018 )")	-	3000	-
4.6 Table 1 (ii)("Matter insoluble in water ( IS 286: 2018 )")	-	2500	-
4.6 Table 1 (iii)("Free caustic alkali, as sodium hydroxide (NaOH) ( IS 286: 2018 )")	-	2500	-

31 Dec, 2026

-
Included w.e.f.24.04.2025

IS 8367 (2023)

TIN POWDER ï¿½ SPECIFICATION

Grade A, Grade B, Grade C, Grade D

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of material)	-	0	NA
Cl-5(Manufacture)	-	0	NA
Cl-6(Grades)	-	0	NA
Cl-7.1, Table-1 (i)(Tin)	-	1500	-
Cl-7.1, Table-1 (ii)(Lead)	-	1500	-
Cl-7.1, Table-1 (iii)(Antimony)	-	1500	-
Cl-7.1, Table-1 (iv)(Copper)	-	1500	-
Cl-7.1, Table-1 (v)(Bismuth)	-	1500	-
Cl-7.1, Table-1 (vi)(Iron)	-	1500	-
Cl-7.1, Table-1 (vii)(Arsenic)	-	1500	-
Cl-7.1, Table-1 (viii)(Other impurities)	-	1500	-
Cl-7.1, Table-1 (ix)(Hydrogen loss)	-	3000	-
Cl-8.1(Apparent Density)	-	2500	-
Cl-8.2(Flow Rate)	-	2500	-
Cl-11(Marking)	-	0	NA
Cl-7.2(Chemical analysis)	-	0	NA
Cl-7.3(Hydrogen loss)	-	0	Testing charges already mentioned above.

31 Dec, 2026

-
Included w.e.f.24.04.2025

IS 3717 (2024)

Refined Secondary Lead ï¿½ Specification (Second Revision)

SPb99.98, SPb99.97, SPb99.99 and SPb99.8

25300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Supply of material)	-	0	NA
Cl-6.1, Table-1 (i)(Lead, Min)	-	1200	-
Cl-6.1, Table-1 (ii)(Impurities, Max:)	-	0	NA
Cl-6.1, Table-1 (iii)(Silver)	-	1200	-
Cl-6.1, Table-1 (iv)(Arsenic)	-	1200	-
Cl-6.1, Table-1 (v)(Bismuth)	-	1200	-
Cl-6.1, Table-1 (vi)(Calcium)	-	1200	-
Cl-6.1, Table-1 (vii)(Cadmium)	-	1200	-
Cl-6.1, Table-1 (viii)(Copper)	-	1200	-
Cl-6.1, Table-1 (ix)(Iron)	-	1200	-
Cl-6.1, Table-1 (x)(Nickel)	-	1200	-
Cl-6.1, Table-1 (xi)(Sulphur)	-	1200	-
Cl-6.1, Table-1 (xii)(Antimony)	-	1200	-
Cl-6.1, Table-1 (xiii)(Selenium)	-	1200	-
Cl-6.1, Table-1 (xiv)(Tin)	-	1200	-
Cl-6.1, Table-1 (xv)(Tellurium)	-	1200	-
Cl-6.1, Table-1 (xvi)(Zinc)	-	1200	-
Cl-6.1, Table-1 (xvii)(Aluminium)	-	1200	-
Cl-6.1, Table-1 (xviii)(Chromium)	-	1200	-
Cl-6.1, Table-1 (xix)(Manganese)	-	1200	-
Cl-6.1, Table-1 (xx)(Total impurities, Max)	-	1200	-
Cl-6.2(chemical analysis)	-	0	NA
Cl-7(Freedom from defects)	-	1000	-
Cl-8(Shape and size)	-	1500	Testing charges for Shape, Size & Mass as per Clause no. 8
Cl-12(Marking)	-	0	NA

31 Dec, 2026

-
Included w.e.f.25.03.2025

IS 2782 (2023)

Refined Nickel- Specification (First Revision)

NR9995, NR9990, NR9982, NR9995, NR9960, NR9900

26500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(General requirements)	-	0	NA
Cl-6(Form and size)	-	1000	-
Cl-7.1, Table-1 (i)(Ni, Min)	-	1100	-
Cl-7.1, Table-1 (ii)(Ni + Co, Min)	-	200	-
Cl-7.1, Table-1 (iii)(Ag, Max)	-	1100	-
Cl-7.1, Table-1 (iv)(Al, Max)	-	1100	-
Cl-7.1, Table-1 (v)(As, Max)	-	1100	-
Cl-7.1, Table-1 (vi)(Bi, Max)	-	1100	-
Cl-7.1, Table-1 (vii)(C, Max)	-	1100	-
Cl-7.1, Table-1 (viii)(Cd, Max)	-	1100	-
Cl-7.1, Table-1 (ix)(Co, Max)	-	1100	-
Cl-7.1, Table-1 (x)(Cu, Max)	-	1100	-
Cl-7.1, Table-1 (xi)(Fe, Max)	-	1100	-
Cl-7.1, Table-1 (xii)(Mn, Max)	-	1100	-
Cl-7.1, Table-1 (xiii)(N, Max)	-	1100	-
Cl-7.1, Table-1 (xiv)(P, Max)	-	1100	-
Cl-7.1, Table-1 (xv)(Pb, Max)	-	1100	-
Cl-7.1, Table-1 (xvi)(S, Max)	-	1100	-
Cl-7.1, Table-1 (xvii)(Sb, Max)	-	1100	-
Cl-7.1, Table-1 (xviii)(Se, Max)	-	1100	-
Cl-7.1, Table-1 (xix)(Si, Max)	-	1100	-
Cl-7.1, Table-1 (xx)(Sn, max)	-	1100	-
Cl-7.1, Table-1 (xxi)(Te, Max)	-	1100	-
Cl-7.1, Table-1 (xxii)(Ti, Max)	-	1100	-
Cl-7.1, Table-1 (xxiii)(Zn, Max)	-	1100	-
Cl-7.1, Table-1 (xxiv)(Mg, Max)	-	1100	-
Cl-7.2(chemical composition)	-	0	-
Cl-11(Marking)	-	0	-

31 Dec, 2026

-
Included w.e.f.25.03.2025

IS 2391 (2024)

Foundry Nickel - Specification (Second Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3(General requirements)	-	0	NA
Cl-4.1 (i)(Nickel (including cobalt))	-	3000	-
Cl-4.1 (ii)(Silicon)	-	1500	-
Cl-4.1 (iii)(Iron)	-	1500	-
Cl-4.1 (iv)(Ni (including cobalt) + Si + Fe)	-	1000	-
Cl-4.1 (v)(Sulphur, Max)	-	1500	-
Cl-4.1 (vi)(Cobalt, Max)	-	1500	-
Cl-7(Marking)	-	0	NA

31 Dec, 2026

-
Included w.e.f 25.03.2025

IS 27 (2023)

Primary Lead - Specification (Fifth Revision).

Pb99.90Cu, Pb99.97, Pb99.985, Pb99.99, Pb 99.995

23500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(General requirements)	-	0	NA
Cl-6(Manufacture)	-	0	NA
Cl-7.1, Table-1(Pb,)	-	1500	-
Cl-7.1, Table-1(Ag,)	-	1500	-
Cl-7.1, Table-1(Fe,)	-	1500	-
Cl-7.1, Table-1(Bi,)	-	1500	-
Cl-7.1, Table-1(Cd,)	-	1500	-
Cl-7.1, Table-1(Cu,)	-	1500	-
Cl-7.1, Table-1(Ni,)	-	1500	-
Cl-7.1, Table-1(As)	-	1500	-
Cl-7.1, Table-1(Sb,)	-	1500	-
Cl-7.1, Table-1(Sn,)	-	1500	-
Cl-7.1, Table-1(Te,)	-	1500	-
Cl-7.1, Table-1(Zn,)	-	1500	-
Cl-7.2(chemical analysis)	-	1500	Testing Charges for Total Impurities (As + Sb + Sn)
Cl-8(Freedom from defects)	-	1500	-
Cl-9(Shape and size)	-	2500	Testing Charges for Shape, Size and Mass
Cl-14(MARKING)	-	0	NA

31 Dec, 2026

-
Included w.e.f.25.03.2025

IS 26 (2024)

Tin ingot - Specification (fifth revision)

Sn99.75, Sn99.85, Sn99.90, Sn99.93, Sn99.95 and Sn99.99

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Suppy of material)	-	0	-
Cl-6(Raw Materials and manufacture)	-	0	-
Cl-7.1, 7.2 Table-1(Sn, Min)	-	1500	-
Cl-7.1, 7.2 Table-1(Sb, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(As, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(Bi, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(Cd, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(Cu, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(Fe, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(Pb, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(Al, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(Zn, Max)	-	1500	-
Cl-7.1, 7.2 Table-1(Total of All Impurities, Max)	-	1500	-
Cl-7.2(Chemical analysis)	-	0	-
Cl-8(Surface condition of ingots)	-	1500	-
Cl-9(Shape and mass of the ingots)	-	2500	-
Cl-14(Marking)	-	0	-

31 Dec, 2026

-
Included w.e.f.25.03.2025

IS 1084 (2005)

Textiles – Manila ropes – Specification (fifth revision)

Grade 1 & Grade 2

33500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.5(Lubrication Weighing or loading materials shall not be used. For the purpose of dressing the fibre or for the preservation of the rope, a lubricant shall be added preferably petroleum products. The quantity of dressing applied to the fibre shall be neither less than 10 percent nor more than 15 percent calculated on the mass of the finished rope when determined by extraction with petroleum ether or other solvent.)	-	2500	-
6.4.1(The angle of lay for all types of ropes shall be 37°)	-	2500	-
4(GRADING )	-	0	NA
6(MANUFACTURE)	-	0	NA
6.1 Table 1 to 3(Manila Fibre )	-	1000	-
6.2 Table 1 to 3(Yarn )	-	1500	-
6.3(Strand )	-	1500	-
6.4(Ropes The ropes shall be well-laid and free from defects and each coil shall be continuous throughout its length and shall not contain loose ends, splices or joints in the strands or in the rope. The number of strands in the rope and the lay of rope, unless otherwise specified, shall be as in next colum:)	-	0	Testing charges already mentioned above at Cl. no. 6.4 The angle of lay i.e. Rs. 2500/-
6.6 IS 3522 (Part 1)(Rot-Proofing Treatment If so ordered, ropes shall be rot-proofed by the application of zinc or copper based rot-proofing agent in appropriate quantity as agreed to protect the rope from fungus and microbial attack. The rot-proofing agent may be applied at the dressing stage for uniform penetration in the rope. Ropes which have been so treated shall otherwise comply, in all respects with the requirements of this standard. When Zn or Copper are extracted in accordance with IS 3522 (Part 1), it shall be minimum 0.5 percent and 0.2 percent respectively.)	-	8000	-
8(REQUIREMENTS)	-	0	-
8.2 IS 7071 (Parts 1 to 3)(Pitch The pitch of rope, when determined in accordance with IS 7071 (Parts 1 to 3) shall conform to the following requirements: Type of Rope: Pitch :)	-	2000	-
8.4(Diameter The diameter of the rope shall not be less than that specified in Tables 1 to 3 and shall not exceed by more than the following tolerances: Diameter: mm)	-	1500	-
8.5 Table: 1 / 2 / 3(No. of yarns per strand)	-	4000	-
8.5 Table: 1 / 2 / 3(Linear density)	-	2000	-
8.5 Table: 1 / 2 / 3(Breaking strength Grade :)	-	4000	-
9(FINISH)	-	1000	-
10,10.1 IS 9560(IDENTIFICATION )	-	2000	-
10.1.1(IDENTIFICATION )	-	0	Testing charges already mentioned above
11 IS 3256(PACKING .)	-	0	NA
6.5(Lubrication Weighing or loading materials shall not be used. For the purpose of dressing the fibre or for the preservation of the rope, a lubricant shall be added preferably petroleum products. The quantity of dressing applied to the fibre shall be neither less than 10 percent nor more than 15 percent calculated on the mass of the finished rope when determined by extraction with petroleum ether or other solvent.)	-	0	Testing charges already mentioned above
6.4.1(The angle of lay for all types of ropes shall be 37°)	-	0	Testing charges already mentioned above
4(GRADING )	-	0	NA
6(MANUFACTURE)	-	0	Testing charges already mentioned above
6.1 Table 1 to 3(Manila Fibre )	-	0	Testing charges already mentioned above
6.2 Table 1 to 3(Yarn )	-	0	Testing charges already mentioned above
6.3(Strand )	-	0	Testing charges already mentioned above
6.4(Ropes The ropes shall be well-laid and free from defects and each coil shall be continuous throughout its length and shall not contain loose ends, splices or joints in the strands or in the rope. The number of strands in the rope and the lay of rope, unless otherwise specified, shall be as in next colum:)	-	0	Testing charges already mentioned above
6.6 IS 3522 (Part 1)(Rot-Proofing Treatment If so ordered, ropes shall be rot-proofed by the application of zinc or copper based rot-proofing agent in appropriate quantity as agreed to protect the rope from fungus and microbial attack. The rot-proofing agent may be applied at the dressing stage for uniform penetration in the rope. Ropes which have been so treated shall otherwise comply, in all respects with the requirements of this standard. When Zn or Copper are extracted in accordance with IS 3522 (Part 1), it shall be minimum 0.5 percent and 0.2 percent respectively.)	-	0	Testing charges already mentioned above
8(REQUIREMENTS)	-	0	NA
8.1 IS 7071 (Part 2)(Mass of the Coil The net mass of the coil shall be determined in accordance with IS 7071 (Part 2). The difference between the observed mass and the calculated value of mass obtained by multiplying nominal linear density of the rope with the length of rope in the coil shall be within limits specified below: Reference No. of Rope)	-	0	NA
8.2 IS 7071 (Parts 1 to 3)(Pitch The pitch of rope, when determined in accordance with IS 7071 (Parts 1 to 3) shall conform to the following requirements: Type of Rope: Pitch :)	-	0	Testing charges already mentioned above
8.3 IS 7071 (Parts 1 to 3)(Length of Coil The length of each coil when tested as per IS 7071 (Parts 1 to 3) shall not be less than 220 m or as declared. However, if so agreed between the buyer and the seller, the length of coil may be tested under zero tension and ± 5 percent tolerance shall be applicable for the rope with diameters less than or equal to 14 and ± 3 percent with a diameter greater than 14 on the specified/declared length.)	-	0	NA
8.4(Diameter The diameter of the rope shall not be less than that specified in Tables 1 to 3 and shall not exceed by more than the following tolerances: Diameter: mm)	-	0	Testing charges already mentioned above
8.5 Table: 1 / 2 / 3(No. of yarns per strand)	-	0	Testing charges already mentioned above
8.5 Table: 1 / 2 / 3(Linear density)	-	0	Testing charges already mentioned above
8.5 Table: 1 / 2 / 3(Breaking strength Grade :)	-	0	Testing charges already mentioned above
9(FINISH)	-	0	Testing charges already mentioned above
10,10.1 IS 9560(IDENTIFICATION )	-	0	Testing charges already mentioned above
10.1.1(IDENTIFICATION )	-	0	Testing charges already mentioned above
11 IS 3256(PACKING .)	-	0	NA
6.5(Lubrication Weighing or loading materials shall not be used. For the purpose of dressing the fibre or for the preservation of the rope, a lubricant shall be added preferably petroleum products. The quantity of dressing applied to the fibre shall be neither less than 10 percent nor more than 15 percent calculated on the mass of the finished rope when determined by extraction with petroleum ether or other solvent.)	-	0	Testing charges already mentioned above
6.4.1(The angle of lay for all types of ropes shall be 37°)	-	0	Testing charges already mentioned above
4(GRADING )	-	0	NA
6(MANUFACTURE)	-	0	NA
6.1 Table 1 to 3(Manila Fibre )	-	0	Testing charges already mentioned above
6.2 Table 1 to 3(Yarn )	-	0	Testing charges already mentioned above
6.3(Strand )	-	0	Testing charges already mentioned above
6.4(Ropes The ropes shall be well-laid and free from defects and each coil shall be continuous throughout its length and shall not contain loose ends, splices or joints in the strands or in the rope. The number of strands in the rope and the lay of rope, unless otherwise specified, shall be as in next colum:)	-	0	Testing charges already mentioned above
6.6 IS 3522 (Part 1)(Rot-Proofing Treatment If so ordered, ropes shall be rot-proofed by the application of zinc or copper based rot-proofing agent in appropriate quantity as agreed to protect the rope from fungus and microbial attack. The rot-proofing agent may be applied at the dressing stage for uniform penetration in the rope. Ropes which have been so treated shall otherwise comply, in all respects with the requirements of this standard. When Zn or Copper are extracted in accordance with IS 3522 (Part 1), it shall be minimum 0.5 percent and 0.2 percent respectively.)	-	0	Testing charges already mentioned above
8(REQUIREMENTS)	-	0	NA
8.1 IS 7071 (Part 2)(Mass of the Coil The net mass of the coil shall be determined in accordance with IS 7071 (Part 2). The difference between the observed mass and the calculated value of mass obtained by multiplying nominal linear density of the rope with the length of rope in the coil shall be within limits specified below: Reference No. of Rope)	-	0	NA
8.2 IS 7071 (Parts 1 to 3)(Pitch The pitch of rope, when determined in accordance with IS 7071 (Parts 1 to 3) shall conform to the following requirements: Type of Rope: Pitch :)	-	0	Testing charges already mentioned above
8.3 IS 7071 (Parts 1 to 3)(Length of Coil The length of each coil when tested as per IS 7071 (Parts 1 to 3) shall not be less than 220 m or as declared. However, if so agreed between the buyer and the seller, the length of coil may be tested under zero tension and ± 5 percent tolerance shall be applicable for the rope with diameters less than or equal to 14 and ± 3 percent with a diameter greater than 14 on the specified/declared length.)	-	0	NA
8.4(Diameter The diameter of the rope shall not be less than that specified in Tables 1 to 3 and shall not exceed by more than the following tolerances: Diameter: mm)	-	0	Testing charges already mentioned above
8.5 Table: 1 / 2 / 3(No. of yarns per strand)	-	0	Testing charges already mentioned above
8.5 Table: 1 / 2 / 3(Linear density)	-	0	Testing charges already mentioned above
8.5 Table: 1 / 2 / 3(Breaking strength Grade :)	-	0	NA
9(FINISH)	-	0	Testing charges already mentioned above
10,10.1 IS 9560(IDENTIFICATION )	-	0	Testing charges already mentioned above
10.1.1(IDENTIFICATION )	-	0	Testing charges already mentioned above
11 IS 3256(PACKING .)	-	0	NA
Cl.6.5(Lubrication)	-	0	Testing charges already mentioned above
Cl.6.6(a)(Rot-Proofing Treatment(Zinc))	-	0	Testing charges already mentioned above
Cl.6.6(b)(Rot-Proofing Treatment(Copper))	-	0	Testing charges already mentioned above
6.1(Manila Fiber)	-	0	Testing charges already mentioned above
6.2(Yarn)	-	0	Testing charges already mentioned above
6.3(Strand)	-	0	Testing charges already mentioned above
6.4(Ropes)	-	0	Testing charges already mentioned above
6.5(Lubrication)	-	0	Testing charges already mentioned above
6.6(Rot proofing Treatment)	-	0	Testing charges already mentioned above
8.1(Mass of the Coil)	-	0	NA
8.2(Pitch)	-	0	Testing charges already mentioned above
8.3(Length of Coil)	-	0	NA
8.4(Diameter)	-	0	Testing charges already mentioned above
8.5-Table 1-(i)(Diameter)	-	0	Testing charges already mentioned above
8.5-Table 1-(ii)(No of Yarns per Strand)	-	0	Testing charges already mentioned above
8.5-Table 1-(iii)(Linear Density)	-	0	Testing charges already mentioned above
8.5-Table 1-(iv)("Tensile Force to be Applied for the Measurement of Liner Density N")	-	0	Testing charges already mentioned above
8.5-Table 1-(v)(Breaking Strength Min)	-	0	NA
8.5-Table 1-(v)(Breaking Strength Min)	-	0	NA
11(Packing)	-	0	NA
12(Marking)	-	0	NA

31 Dec, 2026

-
Included w.e.f.24.02.2025 Exclusion For construction water and compressive strength test only.

IS 3039 (2024)

STRUCTURAL STEEL FOR CONSTRUCTION OF SHIPS - SPECIFICATION (Third revision)

Normal Strength & Higher Strength grades

11800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General requirements)	-	0	NA
Cl-5(Designation and grade)	-	0	NA
Cl-6(Manufacture)	-	0	NA
Cl-7(FREEDOM FROM DEFECTS)	-	500	-
Cl-8(CHEMICAL COMPOSITION)	-	0	NA
Cl-8.3, Table-1(C < 0.20)	-	500	-
Cl-8.3, Table-1(C ≥ 0.20)	-	0	Testing charges already mentioned above
Cl-8.3, Table-1(Mn)	-	500	-
Cl-8.3, Table-1(S)	-	500	-
Cl-8.3, Table-1(P)	-	500	-
Cl-8.3, Table-1(Si)	-	500	-
Cl-8.3, Table-1(N)	-	500	-
Cl-8.3, Table-1(Cr)	-	500	-
Cl-8.3, Table-1(Mo)	-	500	-
Cl-8.3, Table-1(Ni)	-	500	-
Cl-8.3, Table-1(Cu)	-	500	-
Cl-8.3, Table-1(Nb)	-	500	-
Cl-8.3, Table-1(V)	-	500	-
Cl-8.3, Table-1(Ti)	-	500	-
Cl-10.1(Number of Tensile Tests)	-	0	NA
Cl-10.2(Tensile Test Pieces)	-	1500	-
Cl-11(Impact test)	-	1500	-
Cl-13.1(Retest)	-	0	NA
Cl-13.2(Re-heat Treatment)	-	0	NA
Cl-15, Table-2(Beam, column, channel and angle sections including parallel beam and column sections)	-	800	-
Cl-15, Table-2(Tee bars)	-	0	Testing charges already mentioned above at Cl-15, Table-2 (Beam, Column, Channel and angle sections including parallel beam and column sections) i.e. Rs. 800/-
Cl-15, Table-2(Bulb angles)	-	0	Testing charges already mentioned above at Cl-15, Table-2 (Beam, Column, Channel and angle sections including parallel beam and column sections) i.e. Rs. 800/-
Cl-15, Table-2(Plates, sheets and strips and flats)	-	0	Testing charges already mentioned above at Cl-15, Table-2 (Beam, Column, Channel and angle sections including parallel beam and column sections) i.e. Rs. 800/-
Cl-15, Table-2(Round and square bars)	-	0	Testing charges already mentioned above at Cl-15, Table-2 (Beam, Column, Channel and angle sections including parallel beam and column sections) i.e. Rs. 800/-
Cl-15, Table-2(Bulb flats)	-	0	Testing charges already mentioned above at Cl-15, Table-2 (Beam, Column, Channel and angle sections including parallel beam and column sections) i.e. Rs. 800/-
Cl-15, Table-2(Channel sections)	-	0	Testing charges already mentioned above at Cl-15, Table-2 (Beam, Column, Channel and angle sections including parallel beam and column sections) i.e. Rs. 800/-
Cl-15, Table-2(Hollow sections)	-	0	Testing charges already mentioned above at Cl-15, Table-2 (Beam, Column, Channel and angle sections including parallel beam and column sections) i.e. Rs. 800/-
Cl-15, Table-2(Plates for ship's hull structure)	-	0	Testing charges already mentioned above at Cl-15, Table-2 (Beam, Column, Channel and angle sections including parallel beam and column sections) i.e. Rs. 800/-
Cl-16(TOLERANCES)	-	0	NA
Cl-17(CALCLUATION OF MASS)	-	500	-
Cl-18(MARKING)	-	0	NA
Cl-8.1, 8.3, 20, Table-3(C2))	-	0	NA
Cl-8.1, 8.3, 20, Table-3(Si)	-	0	NA
Cl-8.1, 8.3, 20, Table-3(Mn2))	-	0	NA
Cl-8.1, 8.3, 20, Table-3(P)	-	0	NA
Cl-8.1, 8.3, 20, Table-3(S)	-	0	NA
Cl-8.1, 8.3, 20, Table-3(Al)	-	500	-

31 Dec, 2026

-
Included .w.e.f.10.02.2025 Exclusion Cl-12 (Other tests)

IS 2185 : Part 2 (1983)

Specification for concrete masonry units: Part 2 hollow and solid lightweight concrete blocks (First Revision)

Grade A & Grade B

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.7(Moisture Movement)	-	0	NA
8.6(Drying shrinkage)	-	0	NA
8.5, Table 1(Water Absorption)	-	0	NA
8.4, Table 1(Compressive strength)	-	0	NA
8.3(Block Density)	-	0	NA
3.2.5(Thickness of Web)	-	0	NA
3.2.5(Face Shell Thickness)	-	0	NA
3.2(Width)	-	0	NA
3.2(Height)	-	0	NA
3.2(Length)	-	0	NA
8.1(General)	-	1000	-
8.2(Deimension (Length))	-	2000	Testing charges are Rs. 2000/- for Length, Width, Height and Thickness as per clause no. 8.2
8.2(Deimension (Height))	-	0	Testing charges are Rs. 2000/- for Length, Width, Height and Thickness as per clause no. 8.2 Testing charges are Rs. 2000/- for Length, Width, Height and Thickness as per clause no. 8.2 already mentioned above
8.2(Deimension (Width))	-	0	Testing charges are Rs. 2000/- for Length, Width, Height and Thickness as per clause no. 8.2 Testing charges are Rs. 2000/- for Length, Width, Height and Thickness as per clause no. 8.2 already mentioned above
8.3(Block Density)	-	1500	-
8.4(Compressive Strength)	-	2500	-
8.5(Water Absorption)	-	2500	-
8.6(Drying Shrinkage)	-	2500	-
8.7(Moisture Movement)	-	2500	-

31 Dec, 2026

-
Included.w.e.f.10.02.2025

IS 2185 : Part 1 (2005)

Concrete masonry units - Specification: Part 1 hollow and solid concrete blocks (Third Revision)

Grade A & Grade B

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(PHYSICAL REQUIREMENTS-General)	-	1000	-
9.2 & 4.2(PHYSICAL REQUIREMENTS-Nominal Dimensions 1.Length 2.Hight 3. Width)	-	2000	Testing charges are Rs. 2000/- for Length, Width, Height and Thickness as per clause no. 9.2 & 4.2 (Physical Requirements)
9.2 & 4.2.3(Nominal Dimensions-variation in the length of units )	-	0	NA
9.2 & 4.2.3(Nominal Dimensions -variation in height and width of units )	-	0	NA
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the face shell)	-	0	NA
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the Web shell)	-	0	NA
9.3 & 5.1 & 5.2 Table 2(PHYSICAL REQUIREMENTS-Blocks Density - 1.Hollow (Open and Closed Cavity) Concrete Block- Grade Aor Grade B 2.Solid Concrete Block — Grade C)	-	1500	-
9.4- Table 2(PHYSICAL REQUIREMENTS - Compressive Strength 1.Minimum Average Compressive Strength of Units 2.Minimum Average Compressive Strength of Individual Unit)	-	2500	-
9.5(PHYSICAL REQUIREMENTS -Water Absorption)	-	2500	-
9.6(PHYSICAL REQUIREMENTS -Drying Shrinkage)	-	2500	-
9.7(PHYSICAL REQUIREMENTS -Moisture Movement)	-	2500	-
15(Marking)	-	0	NA

31 Dec, 2026

-
Included .w.e.f.10.02.02025

IS 2041 (2024)

Steel Plates and Strips for Pressure Vessels Used at Moderate and Low Temperature â Specification (Fourth Revision)

Room temperature quality and Elevated temperature quality

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General requirements)	-	0	NA
Cl-6(MANUFACTURE)	-	0	NA
Cl-7.1, Table-1(C)	-	600	-
Cl-7.1, Table-1(Si)	-	600	-
Cl-7.1, Table-1(Mn Max)	-	600	-
Cl-7.1, Table-1(P max)	-	600	-
Cl-7.1, Table-1(S Max)	-	600	-
Cl-7.1, Table-1(Al Max)	-	600	-
Cl-7.1, Table-1(N Max)	-	600	-
Cl-7.1, Table-1(Nb Max)	-	600	-
Cl-7.1, Table-1(V Max)	-	600	-
Cl-7.1, Table-1(Ti Max)	-	600	-
Cl-7.1, Table-1(Nb + V + Ti Max)	-	600	-
Cl-7.1, Table-1(Cr Max)	-	600	-
Cl-7.1, Table-1(Cu Max)	-	600	-
Cl-7.1, Table-1(Mo Max)	-	600	-
Cl-7.1, Table-1(Ni Max)	-	600	-
Cl-7.2, Table-2(Carbon)	-	0	NA
Cl-7.2, Table-2(Silicon)	-	0	NA
Cl-7.2, Table-2(Manganese)	-	0	NA
Cl-7.2, Table-2(Phosphorus)	-	0	NA
Cl-7.2, Table-2(Sulphur)	-	0	NA
Cl-7.2, Table-2(Niobium)	-	0	NA
Cl-7.2, Table-2(Vanadium)	-	0	NA
Cl-7.2, Table-2(Titanium)	-	0	NA
Cl-7.2, Table-2(Chromium)	-	0	NA
Cl-7.2, Table-2(Copper)	-	0	NA
Cl-7.2, Table-2(Molybdenum)	-	0	NA
Cl-7.2, Table-2(Nickel)	-	0	NA
Cl-8(HEAT-TREATMENT)	-	0	NA
Cl-9(FREEDOM FROM DEFECTS)	-	1000	-
Cl-9.3(Edge Imperfection)	-	1000	-
Cl-10(DIMENSIONS AND TOLERANCES)	-	1500	-
Cl-11(THEORETICAL MASS)	-	1000	-
Cl-12.1.1(Number of Tests)	-	0	NA
Cl-12.1.2(Orientation of Test Sample)	-	0	NA
Cl-12.1.3(Location of Test Sample)	-	0	NA
Cl-12.1.6(Tensile Test Result)	-	1500	-
Cl-12.2(Bend Test)	-	1500	-
Cl-12.3.1(Charpy impact test)	-	3000	-
Cl-12.3.2(Number of Tests)	-	0	NA
Cl-12.3.3(Orientation)	-	0	NA
Cl-12.5(Re-heat Treatment)	-	0	NA
Cl-14(RUST PROTECTION)	-	500	-
Cl-15(MARKING)	-	0	NA
Cl-4.1(General requirements)	-	-	-
Cl-6(MANUFACTURE)	-	-	-
Cl-7.1, Table-1(C)	-	-	-
Cl-7.1, Table-1(Si)	-	-	-
Cl-7.1, Table-1(Mn Max)	-	-	-
Cl-7.1, Table-1(P max)	-	-	-
Cl-7.1, Table-1(S Max)	-	-	-
Cl-7.1, Table-1(Al Max)	-	-	-
Cl-7.1, Table-1(N Max)	-	-	-
Cl-7.1, Table-1(Nb Max)	-	-	-
Cl-7.1, Table-1(V Max)	-	-	-
Cl-7.1, Table-1(Ti Max)	-	-	-
Cl-7.1, Table-1(Nb + V + Ti Max)	-	-	-
Cl-7.1, Table-1(Cr Max)	-	-	-
Cl-7.1, Table-1(Cu Max)	-	-	-
Cl-7.1, Table-1(Mo Max)	-	-	-
Cl-7.1, Table-1(Ni Max)	-	-	-
Cl-7.2, Table-2(Carbon)	-	-	-
Cl-7.2, Table-2(Silicon)	-	-	-
Cl-7.2, Table-2(Manganese)	-	-	-
Cl-7.2, Table-2(Phosphorus)	-	-	-
Cl-7.2, Table-2(Sulphur)	-	-	-
Cl-7.2, Table-2(Niobium)	-	-	-
Cl-7.2, Table-2(Vanadium)	-	-	-
Cl-7.2, Table-2(Titanium)	-	-	-
Cl-7.2, Table-2(Chromium)	-	-	-
Cl-7.2, Table-2(Copper)	-	-	-
Cl-7.2, Table-2(Molybdenum)	-	-	-
Cl-7.2, Table-2(Nickel)	-	-	-
Cl-8(HEAT-TREATMENT)	-	-	-
Cl-9(FREEDOM FROM DEFECTS)	-	-	-
Cl-9.3(Edge Imperfection)	-	-	-
Cl-10(DIMENSIONS AND TOLERANCES)	-	-	-
Cl-11(THEORETICAL MASS)	-	-	-
Cl-12.1.1(Number of Tests)	-	-	-
Cl-12.1.2(Orientation of Test Sample)	-	-	-
Cl-12.1.3(Location of Test Sample)	-	-	-
Cl-12.1.6(Tensile Test Result)	-	-	-
Cl-12.2(Bend Test)	-	-	-
Cl-12.3.1(Charpy impact test)	-	-	-
Cl-12.3.2(Number of Tests)	-	-	-
Cl-12.3.3(Orientation)	-	-	-
Cl-12.5(Re-heat Treatment)	-	-	-
Cl-14(RUST PROTECTION)	-	-	-
Cl-15(MARKING)	-	-	-

31 Dec, 2026

-
Included w.e.f. 17.02.2025 Exclusion: Cl-13 (ULTRASONIC TESTING), Cl-12.1.6 (Elevated Temperature Tensile as per IS 1608(P-2)

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Ordering Information - IS 737)	-	0	NA
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	0	NA
Cl. 4 (b)(Condition - IS 737)	-	0	NA
Cl. 4 (c)(Quantity in Kg - IS 737)	-	0	NA
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	0	NA
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	0	NA
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	0	NA
Cl. 4 (g)(Packing Mode - IS 737)	-	0	NA
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	0	NA
Cl. 6(Freedom from Defects - IS 737)	-	500	-
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	500	Testing charges for Vanadium, Boron, Gallium, Phosphorus and Zirconium are Rs. 2500/- (Rs. 500/- for each parameter)
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	1000	-
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	Testing charges already mentioned above at Clause no. 7 (Others (Each) i.e. Rs. 1000/-
Cl. 7(Al - IS 504)	-	500	-
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	0	-
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	1500	-
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	1500	-
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	1000	-
Cl. 8.2(Bend Test - IS 1599)	-	1000	-
Cl. 9(Condition - IS 737/ IS 5052)	-	0	NA
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	1500	-
Cl. 11(Selection of Test Samples - IS 737)	-	0	NA
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	0	NA
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	0	NA
Cl. 12(Retests - IS 737/ IS 10259)	-	0	NA
Cl. 13(Packaging - IS 737/ IS 10259)	-	0	NA
Cl. 13.1(Marking - IS 737)	-	0	NA

31 Dec, 2026

-
Included .w.e.f.10.02.2025

IS 18340 (2023)

Vinyl Sulphone - Specification

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1(Description)	-	500	-
Cl-3.2, Table-1 (i)(Assay (by nitrite value), percent by mass (on dry basis), Min)	-	5000	-
Cl-3.2, Table-1 (i)(Assay (by HPLC1)), percent area (on dry basis),Min)	-	0	Testing charges already mentioned above at Cl-3.2, Table-1 (i) Assay (by nitrite value) i.e. Rs. 5000/-
Cl-3.2, Table-1 (ii)(Hydrolysis value, percent by mass (on 100 percent basis), Min)	-	2500	-
Cl-3.2, Table-1 (iii)(Matter insoluble in sodium carbonate solution percent by mass, Max)	-	2000	-
Cl-3.2, Table-1 (iv)(4-Chloroaniline content, percent by mass (on 100 percent basis), Max)	-	5000	-
Cl-4.2(Marking)	-	0	NA

31 Dec, 2026

-
Included w.e.f 20.03.2025

IS 11557 (1986)

Specification for 2 - Naphthylamine - 3 : 6 : 8 - Trisulphonic acid, technical

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Description)	-	1000	-
2.2-Table 1-(i)(Matter insoluble in dilute sodium carbonate)	-	2000	-
2.2-Table 1-(ii)(Assay ( on dry basis ), percent by mass)	-	5000	-
2.2-Table 1-(iii)(Amide G. acid, percent by masss)	-	5000	-
3.1(Packing)	-	0	NA
3.2(Marking)	-	0	NA

31 Dec, 2026

-
Included w.e.f 20.03.2025

IS 8637 (2020)

H Acid ? Specification ( Second Revision )

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	500	-
3.2-Table 1-(i)(Purity (by nitrite value))	-	2500	-
3.2-Table 1-(ii)(Difference between nitrite value and coupling value)	-	2500	-
3.2-Table 1-(iii)(Matter insoluble in sodium carbonate solution)	-	1500	-
3.2-Table 1-(iv)(Purity (by HPCL))	-	4000	-
3.2-Table 1-(v)(Chromotropic acid content,)	-	3000	-
3.2-Table 1-(vi)(Koch’s acid content)	-	3000	-
4.1(Packing )	-	0	NA
4.2(Marking)	-	0	NA

31 Dec, 2026

-
Included w.e.f 20.03.2025

IS 17954 (2023)

TELESCOPIC BALL BEARING DRAWER SLIDE SPECIFICATION

Light Duty / Medium Duty / Heavy Duty / Super Heavy Duty

24800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2, Table- 2 (i)(Internal channel)	-	0	Additional Rs. 7200/- for composition of each metal component (Carbon, Silicon, Manganese, Nickel, Chromium, Sulphur, Phosphorus, Copper, Nitrogen, Boron, Calcium, Molybdenum) and for 6 components 7200 X 6 = Rs. 43200/-.
Cl-4.2, Table- 2 (ii)(Outer channel)	-	0	Testing Charges for Clause no. 5.2 are Rs. 600/-. Testing Charges for Clause no. 5.3 are Rs. 600/-. Testing Charges for Clause no. 5.4 are Rs. 600/-.
Cl-4.2, Table- 2 (iii)(Track up to 550 mm)	-	0	Testing Charges for Clause no. 5.5 are Rs. 600/-. Testing Charges for Clause no. 5.6 are Rs. 600/-.
Cl-4.2, Table- 2 (iv)(Track from 600 mm onwards)	-	0	Testing Charges for Clause no. 5.7 are Rs. 600/-. Testing Charges for Clause no. 5.8 are Rs. 600/-.
Cl-4.2, Table- 2 (v)(Ball cage)	-	0	Testing Charges for Clause no. 5.9 are Rs. 600/-. Testing Charges for Clause no. 5.12 are Rs. 200/-. Testing Charges for Clause no. 5.13 are Rs. 200/-.
Cl-4.2, Table- 2 (vi)(Ball spacer)	-	0	Testing Charges for Clause no. 12 (Salt Spray Test) are Rs. 3500/-. Testing Charges for Clause no. 12 (Coating Thickness) are Rs. 600/-.
Cl-5(Components and Manufacture)	-	0	-
Cl-5(Components and Manufacture)	-	0	-
Cl-6.1(Preparatory Measures)	-	1000	-
Cl-6.2 (a)(Limiting Deviations- Force)	-	0	-
Cl-6.2 (b)(Limiting Deviations- Speed)	-	0	-
Cl-6.2 (c)(Limiting Deviations- Weights)	-	0	-
Cl-6.2 (d)(Limiting Deviations- Dimension)	-	0	-
Cl-6.3(Application of Forces)	-	0	-
Cl-6.4(Testing Equipment)	-	0	-
Cl-6.5(Sequence of testing)	-	0	-
Cl-7(Vertical Load Test)	-	1300	-
Cl-8(Horizontal Load Test)	-	1300	-
Cl-9(Durability Test)	-	7000	-
Cl-10(Deflection Test)	-	1000	-
Cl-11(Slam Test)	-	1500	-
Cl-12(Finish)	-	500	-
Cl-5.11(Ball)	-	600	-
Cl-5.10(Rivets)	-	600	-
4.1(size of the telescopic ball bearing slide)	-	200	-
6.6 (amendment 1)(difference of the maximum forces for opening and closing)	-	500	-
Cl-4.2, Table- 2 (i)(Internal channel)	-	0	Testing Charges already mentioned above
Cl-4.2, Table- 2 (ii)(Outer channel)	-	0	Testing Charges already mentioned above
Cl-4.2, Table- 2 (iii)(Track up to 550 mm)	-	0	Testing Charges already mentioned above
Cl-4.2, Table- 2 (iv)(Track from 600 mm onwards)	-	0	Testing Charges already mentioned above
Cl-4.2, Table- 2 (v)(Ball cage)	-	0	Testing Charges already mentioned above
Cl-4.2, Table- 2 (vi)(Ball spacer)	-	0	Testing Charges already mentioned above
Cl-5(Components and Manufacture)	-	0	Testing Charges already mentioned above
Cl-5(Components and Manufacture)	-	0	Testing Charges already mentioned above
Cl-6.1(Preparatory Measures)	-	0	Testing Charges already mentioned above
Cl-6.2 (a)(Limiting Deviations- Force)	-	0	Testing Charges already mentioned above
Cl-6.2 (b)(Limiting Deviations- Speed)	-	0	Testing Charges already mentioned above
Cl-6.2 (c)(Limiting Deviations- Weights)	-	0	Testing Charges already mentioned above
Cl-6.2 (d)(Limiting Deviations- Dimension)	-	0	Testing Charges already mentioned above
Cl-6.3(Application of Forces)	-	0	Testing Charges already mentioned above
Cl-6.4(Testing Equipment)	-	0	Testing Charges already mentioned above
Cl-6.5(Sequence of testing)	-	0	Testing Charges already mentioned above
Cl-7(Vertical Load Test)	-	0	Testing Charges already mentioned above
Cl-8(Horizontal Load Test)	-	0	Testing Charges already mentioned above
Cl-9(Durability Test)	-	0	Testing Charges already mentioned above
Cl-10(Deflection Test)	-	0	Testing Charges already mentioned above
Cl-11(Slam Test)	-	0	Testing Charges already mentioned above
Cl-12(Finish)	-	0	Testing Charges already mentioned above
Cl-5.11(Ball)	-	0	Testing Charges already mentioned above
Cl-5.10(Rivets)	-	0	Testing Charges already mentioned above
4.1(size of the telescopic ball bearing slide)	-	0	Testing Charges already mentioned above
6.6 (amendment 1)(difference of the maximum forces for opening and closing)	-	0	Testing Charges already mentioned above

31 Dec, 2026

-
Included w.e.f 30.01.2025

IS 297 (2024)

SODIUM SULPHIDE, TECHNICAL - SPECIFICATION (Third Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1("Description ( IS 297 : 2024 )")	-	500	-
3.2 Table 1 (i)("Total sulphides (as Na₂S) ( IS 297 : 2024 )")	-	1200	-
3.2 Table 1 (ii)("Sodium hydrosulphide (as NaHS) ( IS 297 : 2024 )")	-	1000	-
3.2 Table 1 (iii)("Excess alkali (as Na₂CO₃) ( IS 297 : 2024 )")	-	1000	-
3.2 Table 1 (iv)("Reducing compounds (other than sodium sulphide and sodium hydrosulphide)(as Na₂S₂O₃) ( IS 297 : 2024 )")	-	1000	-
3.2 Table 1 (v)("Iron and aluminum compounds (as Fe₂O₃) ( IS 297 : 2024 )")	-	1000	-
3.2 Table 1 (vi)("Sodium sulphate (as Na₂SO₄) ( IS 297 : 2024 )")	-	1000	-
3.2 Table 1 (vii)("Chloride (as NaCl) ( IS 297 : 2024 )")	-	1000	-
3.2 Table 1 (viii)("Water insolubles (other than iron and aluminum compounds) ( IS 297 : 2024 )")	-	800	-

31 Dec, 2026

-
Included w.e.f.16.12.2024

IS 251 (2024)

SODA ASH, TECHNICAL â SPECIFICATION (fifth revision)

Dense, Medium, Light

8300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1("Description ( IS 251 : 2024 )")	-	500	-
4.2("Bulk Density ( IS 251 : 2024 )")	-	800	-
4.3("Volatile Matter Content ( IS 251 : 2024 )")	-	800	-
4.4("Sieve Analysis of Dense Grade Soda Ash ( IS 251 : 2024 )")	-	0	Testing for Sieve analysis are mentioned below.
4.4.1("Material retained on 1.70 mm IS Sieve ( IS 251 : 2024 )")	-	800	-
4.4.1("Material passing through 75 μm IS Sieve ( IS 251 : 2024 )")	-	800	-
4.5 Table 1 (i)("Total alkalinity (as Na₂CO₃) ( IS 251 : 2024 )")	-	800	-
4.5 Table 1 (ii)("Matter insoluble in water ( IS 251 : 2024 )")	-	800	-
4.5 Table 1 (iii)("Sulphate (Na₂SO₄) ( IS 251 : 2024 )")	-	1000	-
4.5 Table 1 (iv)("Chloride (as NaCl) ( IS 251 : 2024 )")	-	1000	-
4.5 Table 1 (5)("Iron (as Fe₂O₃) ( IS 251 : 2024 )")	-	1000	-

31 Dec, 2026

-
Included w.e.f.13.12.2024

IS 266 (2024)

Sulphuric Acid âSpecification (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, 4.1.1(Technical Grade (Description))	-	800	Testing Charges 1) Battery Grade (Conc.) INR 15000 2) Battery Grade (Dil.) INR 14000 3) AR Grade INR 10000 4) Chemically Pure Grade INR 9000 5) Technical Grade INR 6000
4.1, 4.1.2(Battery Grade (Concentrated) (Description))	-	800	-
4.1, 4.1.2(Battery Grade (Dilute) (Description))	-	800	-
4.1, 4.1.3(Chemically Pure Grade (Description))	-	800	-
4.1, 4.1.3(Analytical Reagent Grade (Description))	-	800	-
4.3.1 & Table 1, S.No (i)("Total acidity (as H2SO4) (Technical Grade)")	-	1200	-
4.3.1 & Table 1, S.No (ii)("Residue on ignition (Technical Grade)")	-	1000	-
4.3.1 & Table 1, S.No (iii)("Iron (as Fe) (Technical Grade)")	-	1000	-
4.3.1 & Table 1, S.No (v)("Heavy metals (as lead) (Technical Grade)")	-	1000	-
4.3.1 & Table 1, S.No (vi)("Arsenic (as As) (Technical Grade)")	-	1000	-
4.3.2 & Table 1, S.No (i)("Total acidity (as H2SO4) (Battery Grade Concentrated)")	-	1200	-
4.3.2 & Table 1, S.No (ii)("Residue on ignition (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (iii)("Iron (as Fe) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (iv)("Chloride (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (vi)("Arsenic (as As) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (viii)("Organic Matter (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xi)("Selenium (as Se) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xii)("Manganese (as Mn) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xiii)("Copper (as Cu) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xiv)("Zinc (as Zn) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Battery Grade Concentrated)")	-	1000	-
4.3.2 & Table 1, S.No (i)("Total acidity (as H2SO4) (Battery Grade Diluted)")	-	1200	-
4.3.2 & Table 1, S.No (ii)("Residue on ignition (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (iii)("Iron (as Fe) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (iv)("Chloride (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (vi)("Arsenic (as As) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xi)("Selenium (as Se) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xii)("Manganese (as Mn) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xiii)("Copper (as Cu) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xiv)("Zinc (as Zn) (Battery Grade Diluted)")	-	1000	-
4.3.2 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Battery Grade Diluted)")	-	1000	-
4.1.3 & Table 1, S.No (i)("Total acidity (as H2SO4) (Chemically Pure Grade)")	-	1200	-
4.1.3 & Table 1, S.No (ii)("Residue on ignition (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (iii)("Iron (as Fe) (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (iv)("Chloride (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (v)("Heavy metals (as lead) (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Chemically Pure Grade)")	-	1000	-
4.1.3 & Table 1, S.No (i)("Total acidity (as H2SO4) (Analytical Reagent Grade)")	-	1200	-
4.1.3 & Table 1, S.No (ii)("Residue on ignition (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (iii)("Iron (as Fe) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (iv)("Chloride (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (v)("Heavy metals (as lead) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vii)("Nitrates (as NO3) (Analytical Reagent Grade)")	-	1000	-
4.1.3 & Table 1, S.No (vii)("Ammonia (as NH3) (Analytical Reagent Grade)")	-	1000	-
4.3.2.2 a)("Antimony (as Sb) (Battery Grade Concentrated acid)")	-	1000	-
4.3.2.2 a)("Antimony (as Sb) (Battery Grade Diluted acid)")	-	1000	-
4.3.2.2 b)(Platinum (as Pt) (Battery Grade Concentrated acid))	-	1000	-
4.3.2.2 b)(Platinum (as Pt) (Battery Grade Diluted acid))	-	1000	-
4.1, 4.1.1(Technical Grade (Description))	-	-	-
4.1, 4.1.2(Battery Grade (Concentrated) (Description))	-	-	-
4.1, 4.1.2(Battery Grade (Dilute) (Description))	-	-	-
4.1, 4.1.3(Chemically Pure Grade (Description))	-	-	-
4.1, 4.1.3(Analytical Reagent Grade (Description))	-	-	-
4.3.1 & Table 1, S.No (i)("Total acidity (as H2SO4) (Technical Grade)")	-	-	-
4.3.1 & Table 1, S.No (ii)("Residue on ignition (Technical Grade)")	-	-	-
4.3.1 & Table 1, S.No (iii)("Iron (as Fe) (Technical Grade)")	-	-	-
4.3.1 & Table 1, S.No (v)("Heavy metals (as lead) (Technical Grade)")	-	-	-
4.3.1 & Table 1, S.No (vi)("Arsenic (as As) (Technical Grade)")	-	-	-
4.3.2 & Table 1, S.No (i)("Total acidity (as H2SO4) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (ii)("Residue on ignition (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (iii)("Iron (as Fe) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (iv)("Chloride (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (vi)("Arsenic (as As) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (viii)("Organic Matter (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xi)("Selenium (as Se) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xii)("Manganese (as Mn) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xiii)("Copper (as Cu) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xiv)("Zinc (as Zn) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Battery Grade Concentrated)")	-	-	-
4.3.2 & Table 1, S.No (i)("Total acidity (as H2SO4) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (ii)("Residue on ignition (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (iii)("Iron (as Fe) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (iv)("Chloride (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (vi)("Arsenic (as As) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xi)("Selenium (as Se) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xii)("Manganese (as Mn) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xiii)("Copper (as Cu) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xiv)("Zinc (as Zn) (Battery Grade Diluted)")	-	-	-
4.3.2 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Battery Grade Diluted)")	-	-	-
4.1.3 & Table 1, S.No (i)("Total acidity (as H2SO4) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (ii)("Residue on ignition (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (iii)("Iron (as Fe) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (iv)("Chloride (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (v)("Heavy metals (as lead) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (xv)("Nitrates, nitrites and ammonia (as N) (Chemically Pure Grade)")	-	-	-
4.1.3 & Table 1, S.No (i)("Total acidity (as H2SO4) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (ii)("Residue on ignition (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (iii)("Iron (as Fe) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (iv)("Chloride (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (v)("Heavy metals (as lead) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vi)("Arsenic (as As) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vii)("Oxidizable impurities (as SO2), (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vii)("Nitrates (as NO3) (Analytical Reagent Grade)")	-	-	-
4.1.3 & Table 1, S.No (vii)("Ammonia (as NH3) (Analytical Reagent Grade)")	-	-	-
4.3.2.2 a)("Antimony (as Sb) (Battery Grade Concentrated acid)")	-	-	-
4.3.2.2 a)("Antimony (as Sb) (Battery Grade Diluted acid)")	-	-	-
4.3.2.2 b)(Platinum (as Pt) (Battery Grade Concentrated acid))	-	-	-
4.3.2.2 b)(Platinum (as Pt) (Battery Grade Diluted acid))	-	-	-

31 Dec, 2026

-
Included w.e.f.10.12.2024

IS 7686 (2020)

Specification for 3 ( N, N-Diethyl ) Aminophenol ( First Revision )

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.1(Description)	-	1000	-
Cl. 3.2(Solubility in alcohol, ether, sodium hydroxide and hydrochloric acid)	-	2000	-
Cl. 3.3, Table 1, Sr. No (i), A-2(Crystallizing point,)	-	3500	-
Cl. 3.3, Table 1, Sr. No (ii), A-3(Purity by CV)	-	3000	-
Cl. 3.3, Table 1, Sr. No (iii), B(Purity by HPLC)	-	4000	-
Cl. 3.3, Table 1, Sr. No (iv), C(Salt content as NaCl)	-	2500	-
Cl. 3.1(Description)	-	0	NA
Cl. 3.2(Solubility in alcohol, ether, sodium hydroxide and hydrochloric acid)	-	0	NA
Cl. 3.3, Table 1, Sr. No (i), A-2(Crystallizing point,)	-	0	NA
Cl. 3.3, Table 1, Sr. No (ii), A-3(Purity by CV)	-	0	NA
Cl. 3.3, Table 1, Sr. No (iii), B(Purity by HPLC)	-	0	NA
Cl. 3.3, Table 1, Sr. No (iv), C(Salt content as NaCl)	-	0	NA

31 Dec, 2026

-
Included w.e.f. 03.03.2025

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

IDMA LABORATORIES LIMITED

PLOT NO. 391 INDUSTRIAL AREA PHASE 1, PANCHKULA, Panchkula, Haryana, 134113

9888002607 testing@idmagroup.co.in

Scope List