BIS - LIMS (Laboratory Information Management System)

EMC Testing and Compliance LLP, Gurugram

115, Pace City-1, Sector 37, Gurugram, Gurugram, Haryana, 122001

8130427070 info@emclab.co.in

Scope List

Reset

156 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 6719 (1972)

Solid Pvc Soles And Heels

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6.1(Hardness )	-	600	-
3.6 (vi)(Lead (as Pb) ppm)	-	990	-
3.6 (v)(Volatility, percent by means )	-	800	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	500	-
3.6 (iii)(Elongation at break, percent )	-	500	-
3.6 (ii)(Tensile Strength )	-	500	-
3.6 (i)(Relative density )	-	300	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	150	-
Cl. 6.4(Measurement of thickness)	-	500	-

19 Jul, 2027

-
-

122

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Size & Thickness )	-	180	-
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	150	-
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	300	-
Cl.4.1.3 And 8.3,Table1, iii)(Hardness, Shore A durometer min)	-	300	-
Cl.4.1.3 And 8.3,Table1(iii) Change in Hardness after ageing at 100±1°C for 24hr)	-	2300	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	700	-
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	500	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi)(Heat shrinkage test at 100±1°C for 1 hour max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table1, viii)(Water absorption , percent by mass, Max)	-	630	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii)(Flexing resistance: Maximum cut growth at 50 000 cycles)	-	1200	-
5, 5.1(Marking)	-	180	-
6, 6.1(Packing)	-	180	-

19 Jul, 2027

-
-

123

IS 15844 (2010)

Sports Footwear Specification

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.11(Corrosion resistance)	-	700	-
3.10(Ross Flex test)	-	1000	-
3.10(Collapsing load )	-	800	-
3.10(Crush load )	-	500	-
3.9(Lace abrasion test)	-	800	-
3.9(Griping Strength of Tags)	-	500	-
3.9(Colour migration / Colour fastness)	-	300	-
3.9(Breaking Strength )	-	500	-
3.8(Heat resistance tester )	-	500	-
3.8(Compression set )	-	1000	-
3.8(Die-C tear Strength )	-	500	-
3.8(Elongation at Break )	-	500	-
3.8(Tensile Strength)	-	500	-
3.7(Flexing index)	-	500	-
3.7(Abrasion resistance )	-	800	-
3.7(Water absorption & loss percent )	-	630	-
3.7(Tensile Strength)	-	500	-
3.6(Ross flexing )	-	2000	-
3.6(Adhesion to mid sole )	-	800	-
3.6(Abrasion resistance )	-	1080	-
3.6(Die-C tear Strength )	-	500	-
3.6(Trouser tear strength )	-	500	-
3.5(Heat resistance tester )	-	500	-
3.5(Adhesive to sole)	-	800	-
3.5(Compression set )	-	1000	-
3.5(Die-C tear Strength )	-	500	-
3.5(Split tear strength )	-	500	-
3.5(Elongation at Break )	-	500	-
3.5(Tensile Strength)	-	500	-
3.4(Colorfastness to light )	-	300	-
3.4(Colour fastness to crocking )	-	300	-
3.4(Tear Strength)	-	500	-
3.4(Elongation at Break )	-	500	-
3.4(Tensile Strength)	-	500	-
3.4(Adhesive Strength )	-	800	-
3.4(Hydrolysis )	-	1000	-
3.4(Upper flexing resistance )	-	1000	-
3.3.4(Energy absorption of seat region )	-	630	-
3.3.3(Sole /midsole bond strength )	-	800	-
3.3.2(Upper/outsole bond strength)	-	800	-
3.3.1(Contruction)	-	100	-
3.2.3 & 3.2.4(Visual )	-	100	-
3.2.1(Design )	-	100	-
Cl. 3.6,Table 7,IS 3400(Part 17), iv)(Tear strength, kg/cm, Min)	-	500	-
Cl. 3.4,Table 3(Lastometer test, mm, Min)	-	500	-

19 Jul, 2027

-
-

124

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	100	-
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	600	-
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	500	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	150	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	1350	-
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	1000	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	500	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	630	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	500	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	-
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	100	-
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	100	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	500	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	800	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	500	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	1350	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	1350	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	500	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	630	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	1350	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	1000	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	100	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	1350	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	800	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	100	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	600	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	1000	-
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	180	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	100	-
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	100	-
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	180	-
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	500	-
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	800	-
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	100	-
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	100	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	100	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	100	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	100	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	100	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	150	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	180	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	630	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	800	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	800	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	800	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	630	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	180	-
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	1080	-
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	1080	-
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	800	-
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	2700	-
5.2.4(Reinforcing Material)	-	100	-
5.2.8.4(Colour of the lace)	-	100	-
Cl. 5.3(Construction 5.3.1,5.3.3,5.3.4)	-	100	-
8(CHEMICAL REQUIREMENTS)	-	4450	-
10(Marking)	-	180	-
11(PACKING)	-	180	-

19 Jul, 2027

-
-

125

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	500	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	1000	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	500	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	500	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	500	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	500	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	1000	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	500	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	500	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	500	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	500	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	500	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	1000	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	500	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	500	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	500	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	500	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	500	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	500	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	500	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	500	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	500	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	500	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	500	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	500	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	500	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	500	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	500	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	500	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	500	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	500	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	500	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	500	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	500	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	500	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	500	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	500	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	500	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	500	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	500	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	500	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	500	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	500	-

19 Jul, 2027

-
-

126

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

Electric Toys and Non-Electric toys (all ranges)

2000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2-5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	2000	10% discount for BIS
4.2.2(a)-5.2(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more)	-	2000	10% discount for BIS
4.2.2(b)-5.2(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm)	-	2000	10% discount for BIS
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	2000	10% discount for BIS
4.5-5.5(Soft-filled toys-Test for soft-filled toys )	-	2000	10% discount for BIS
4.5-5.5(Soft-filled toys-rate of spread of flame )	-	2000	10% discount for BIS
4.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	10% discount for BIS
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	10% discount for BIS
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	2000	10% discount for BIS
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame)	-	2000	10% discount for BIS
4.3(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play)	-	2000	10% discount for BIS
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	2000	10% discount for BIS
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-	2000	10% discount for BIS
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	10% discount for BIS
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	2000	10% discount for BIS
4.2.4-5.3(Toys to be worn on the head-Full or partial moulded head masks-maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	2000	10% discount for BIS
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy- maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	2000	10% discount for BIS
4.1(General)	-	200	10% discount for BIS

19 Jul, 2027

-
-

127

IS 798 (2020)

Orthophosphoric Acid — Specification ( Third Revision )

Orthophosphoric Acid (Any Grade)

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description)	-	2000	-
5.2.2 Table 1 (i)(Relative density )	-	2000	-
5.2.2 Table 1 (ii)(Orthophosphoric acid (H3 PO4 ))	-	2000	-
5.2.2 Table 1 (iii)(Iron (as Fe), )	-	2000	-
5.2.2 Table 1 (iv)(Chlorides (as Cl), )	-	2000	-
5.2.2 Table 1 (v)(Sulphates (as SO4 ), )	-	2000	-
5.2.2 Table 1 (vi)(Arsenic (as As2 O3 ), )	-	2000	-
5.2.2 Table 1 (vii)(Antimony (as Sb2 O3 ), )	-	2000	-
5.2.2 Table 1 (viii)(Nitrates (as NO3 ),)	-	2000	-
5.2.2 Table 1 (ix)(Lead (as Pb), parts per million, Max)	-	2000	-
5.2.2 Table 1 (x)(Silica (as SiO2 ), )	-	2000	-
5.2.2 Table 1 (xi)(Calcium (as Ca) and Magnesium (as Mg), )	-	2000	-
5.2.2 Table 1 (xii)(Oxygen absorbed (as O),)	-	2000	-
5.2.2 Table 1 (xiii)(Volatile acids)	-	2000	-
5.2.2 Table 1 (xiv)(Manganese (as Mn), )	-	2000	-
5.2.2 Table 1 (xv)(Molybdenum (as Mo), )	-	2000	-
5.2.2 Table 1 (xvi)(Mercury (as Hg), )	-	2000	-
5.2.2 Table 1 (xvii)(Aluminium (as Al), )	-	2000	-

19 Jul, 2027

-
-

128

IS 302 : Part 2 : Sec 14 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 14 electric kitchen machines (First Revision)

---

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	0	-
7.1(Marking- IS 302-1)	-	1000	-
7.3(Marking- IS 302-1)	-	0	-
7.4(Marking- IS 302-1)	-	0	-
7.6(Marking- IS 302-1)	-	0	-
7.7(Marking- IS 302-1)	-	0	-
7.8(Marking- IS 302-1)	-	0	-
7.11(Marking- IS 302-1)	-	0	-
7.12(Marking- IS 302-1)	-	0	-
7.13(Marking- IS 302-1)	-	0	-
7.14(Marking- IS 302-1)	-	0	-
7.15(Marking- IS 302-1)	-	0	-
7.101(Marking)	-	1000	-
8( Protection Against Electric Shock, IS 302-1)	-	2000	-
10(Power Input and Current, IS 302-1)	-	2000	-
11(Heating, IS 302-1)	-	2000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	1000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	1000	-
14(Transient Over Voltages, IS 302-1)	-	10000	-
15(Moisture Resistance, IS 302-1)	-	5000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	1000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	1000	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	5000	-
19.1(Abnormal Operation, IS 302-1)	-	0	-
19.7(Abnormal Operation, IS 302-1)	-	0	-
19.8(Abnormal Operation, IS 302-1)	-	0	-
19.9(Abnormal Operation, IS 302-1)	-	0	-
19.101(Abnormal Operation)	-	1000	-
19.102(Abnormal Operation)	-	2000	-
19.11.4.1(Electrostatic discharges)	-	3000	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	3000	-
19.11.4.4(Surge immunity test)	-	3000	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	3000	-
19.11.4.7(Harmonics)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
32(Radiation, Toxicity and similar Hazard IS 302-1)	-	0	-
31(Resistance of Rusting, IS 302-1)	-	5000	-
30.2(Resistance to Heat and Fire, IS 302-1)	-	1000	-
30.1(Resistance to Heat and Fire, IS 302-1)	-	1000	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	2000	-

19 Jul, 2027

-
Exclusion Cl 19.11.4.2 to Cl 19.11.4.7

129

IS 1989 : Part 2 (1986)

Specification for leather safety boots and shoes: Part 2 for heavy metal industries (Fourth Revision)

7650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Marking)	-	180	-
4(Marking)	-	180	-
7(Design)	-	100	-
8(a) Upper Leather)	-	500	-
8(b) Lining Leather)	-	500	-
8(c) Bottom Material)	-	500	-
8(d) Steel Toe Cap)	-	500	-
8(e) Tape)	-	500	-
8(f) Bottom Filling)	-	500	-
8(g) Eyelet)	-	500	-
8(h) Toe Compound)	-	500	-
8(i) Threads)	-	500	-
8(j) Rivets)	-	500	-
8(k) Screw Wire)	-	500	-
8(l) Heel Pin)	-	500	-
8(m) Shank)	-	500	-
8(n) Laces)	-	500	-
8(o) Tongue Lining)	-	500	-
8(p) Adhesive)	-	500	-
8(q) Strengthening Piece)	-	500	-
8(r) Leather Components)	-	500	-
9(Manufacture)	-	500	-
10(Finish)	-	500	-
11(a) Boots with Leather Sole and Heel)	-	150	-
11(b) Boots with Rubber Sole and Heel)	-	150	-
12(Performance Test)	-	630	-
13(Design)	-	100	-
14(a) Upper Leather)	-	100	-
14(b) Lining Leather)	-	100	-
14(c) Bottom Material)	-	100	-
14(d) Steel Toe Cap)	-	100	-
14(e) Tape)	-	100	-
14(f) Bottom Filling)	-	100	-
14(g) Eyelet)	-	100	-
14(h) Toe Compound)	-	100	-
14(i) Threads)	-	100	-
14(j) Rivets)	-	100	-
14(k) Screw Wire)	-	100	-
14(l) Heel Pin)	-	100	-
14(m) Shank)	-	100	-
14(n) Laces)	-	100	-
14(o) Tongue Lining)	-	100	-
14(p) Adhesive)	-	100	-
14(q) Leather Components)	-	100	-
15(Manufacture)	-	100	-
16(Finish)	-	500	-
17(a) Shoes with Leather Sole and Heel)	-	150	-
17(b) Shoes with Rubber Sole and Heel)	-	150	-
18(Performance Test)	-	630	-

19 Jul, 2027

-
-

130

IS 1989 : Part 1 (1986)

Specification for leather safety boots and shoes: Part 1 for miners (Fourth Revision)

Leather Safety Boots and Shoes

10328 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 (a)(Marking)	-	500	-
4.1 (b)(Marking)	-	500	-
4.1 (c)(Marking)	-	500	-
4.1 (d)(Marking)	-	500	-
4.1 (e)(Marking)	-	500	-
7.1(Design)	-	500	-
4.1 (a)(Marking)	-	500	-
4.1 (b)(Marking)	-	500	-
4.1 (c)(Marking)	-	500	-
4.1 (d)(Marking)	-	500	-
4.1 (e)(Marking)	-	500	-
7.1(Design)	-	1000	-
10.1(Finish)	-	2000	-
10.3(Finish)	-	2000	-
10.4(Finish)	-	2000	-
11.1(Mass Boots with Leather Sole and Heel)	-	2000	-
12(Performance test)	-	5000	-

19 Jul, 2027

-
-

131

IS 16103 : Part 1 (2012)

Led modules for general lighting: Part 1 safety requirements

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	1000	5 % Discount for BIS
8(Terminals)	-	2000	5 % Discount for BIS
9(PROVISION FOR EARTHING)	-	2000	5 % Discount for BIS
10(Protection against accidental contact with live parts)	-	2000	5 % Discount for BIS
11(Mositure Resistance and Insulation)	-	10000	5 % Discount for BIS
12(Electric Strength)	-	2000	5 % Discount for BIS
13(Fault conditions)	-	2000	5 % Discount for BIS
15(Construction)	-	2000	5 % Discount for BIS
16(Creepage distance and clearances)	-	2000	5 % Discount for BIS
17(Screws, current carrying parts and connections)	-	2000	5 % Discount for BIS
18(Resistance to heat, fire and tracking)	-	2000	5 % Discount for BIS
19(Resistance to corrosion)	-	5000	5 % Discount for BIS
21(Heat management)	-	1000	5 % Discount for BIS

19 Jul, 2027

-
-

132

IS 10322 : Part 5 : Sec 2 (2012)

Luminaires: Part 5 particular requirements: Sec 2 recessed luminaires (First Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	500	5 % Discount for BIS
5(Classification of Luminaires')	-	500	5 % Discount for BIS
6(Marking)	-	1000	5 % Discount for BIS
7(Construction)	-	2000	5 % Discount for BIS
8(Creepage Distance and Clearances)	-	2000	5 % Discount for BIS
9(Provision for earthing)	-	2000	5 % Discount for BIS
10(Terminals)	-	2000	5 % Discount for BIS
11(External & Internal Wiring)	-	2000	5 % Discount for BIS
12(Protection against electric shock)	-	2000	5 % Discount for BIS
13(Endurance Tests and Thermal Tests)	-	10000	5 % Discount for BIS
14(Resistance to Dust and Moisture)	-	10000	5 % Discount for BIS
15(Insulation Resistance and Electric Strength)	-	5000	5 % Discount for BIS
16(Resistance to Heat , fire and tracking)	-	2000	5 % Discount for BIS
17(Photometric Test)	-	0	5 % Discount for BIS

19 Jul, 2027

-
-

133

IS 10322 : PART 5 : SEC 3 (2012)

Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	500	5 % Discount for BIS
5(Classification of Luminaires')	-	500	5 % Discount for BIS
6.0(Marking)	-	1000	5 % Discount for BIS
7.0(Construction)	-	2000	5 % Discount for BIS
8.0(Creepage Distance and Clearances)	-	2000	5 % Discount for BIS
9.0(Provision for earthing)	-	2000	5 % Discount for BIS
10.0(Terminals)	-	2000	5 % Discount for BIS
11.0(External & Internal Wiring)	-	2000	5 % Discount for BIS
12.0(Protection against electric shock)	-	2000	5 % Discount for BIS
13.0(Endurance Tests and Thermal Tests)	-	10000	5 % Discount for BIS
14.0(Resistance to Dust & Moisture)	-	10000	5 % Discount for BIS
15.0(Insulation Resistance and Electric Strength)	-	5000	5 % Discount for BIS
16.0(Resistance to Heat , fire and tracking)	-	2000	5 % Discount for BIS
17.0(Photometric Test)	-	0	5 % Discount for BIS

19 Jul, 2027

-
-

134

IS 10322 : Part 5 : Sec 5 (2013)

Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	500	5 % Discount for BIS
5(Classification of Luminaires')	-	500	5 % Discount for BIS
6.0(Marking)	-	1000	5 % Discount for BIS
7.0(Construction)	-	500	5 % Discount for BIS
8.0(Creepage Distance and Clearances)	-	2000	5 % Discount for BIS
9.0(Provision for earthing)	-	2000	5 % Discount for BIS
10.0(Terminals)	-	2000	5 % Discount for BIS
11.0(External & Internal Wiring)	-	2000	5 % Discount for BIS
12.0(Protection against electric shock)	-	2000	5 % Discount for BIS
13.0(Endurance Tests and Thermal Tests)	-	10000	5 % Discount for BIS
14.0(Resistance to Dust & Moisture)	-	10000	5 % Discount for BIS
15.0(Insulation Resistance and Electric Strength)	-	5000	5 % Discount for BIS
16.0(Resistance to Heat , fire and tracking)	-	2000	5 % Discount for BIS

19 Jul, 2027

-
-

135

IS 9873 : Part 9 (2017)

Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children's Products

Electric Toys and Non-Electric toys (all ranges)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	5000	10% Discount for BIS samples
3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	5000	10% Discount for BIS samples
3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	5000	10% Discount for BIS samples
3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	5000	10% Discount for BIS samples
3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	5000	10% Discount for BIS samples
3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	5000	10% Discount for BIS samples
3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	5000	10% Discount for BIS samples
3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	5000	10% Discount for BIS samples

19 Jul, 2027

-
-

136

IS 9873 : Part 3 (2017)

Safety of toys: Part 3 migration of certain elements (Second Revision)

Toys and Similar products

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	3000	10 % discount for BIS Samples
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	3000	10 % discount for BIS Samples
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	3000	10 % discount for BIS Samples
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	3000	10 % discount for BIS Samples
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	3000	10 % discount for BIS Samples
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	3000	10 % discount for BIS Samples
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	3000	10 % discount for BIS Samples
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	3000	10 % discount for BIS Samples

19 Jul, 2027

-
-

137

IS 10322 : Part 5 : Sec 9 (2017)

Luminaires: Part 5 particular requirements: Sec 9 rope lights

Supply voltages not exceeding 250V

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
21.5(Classification of Luminaires')	-	2000	10% Discount for BIS
21.6(Marking)	-	2000	10% Discount for BIS
21.7(Construction)	-	20000	10% Discount for BIS
21.8(Creepage Distance and Clearances)	-	5000	10% Discount for BIS
21.10(Terminals)	-	2000	10% Discount for BIS
21.11(External & Internal Wiring)	-	2000	10% Discount for BIS
21.12(Protection against electric shock)	-	5000	10% Discount for BIS
21.13(Endurance Tests and Thermal Tests)	-	15000	10% Discount for BIS
21.14(Resistance to Dust & Moisture)	-	2000	10% Discount for BIS
21.15(Insulation Resistance and Electric Strength)	-	15000	10% Discount for BIS
21.16(Resistance to Heat , fire and tracking)	-	5000	10% Discount for BIS

19 Jul, 2027

-
-

138

IS 16333 : Part 3 (2017)

Mobile phone handsets: Part 3 indian language support for mobile phone handsets - Specific requirements (First Revision)

Mobile Phone Languages

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1(Inputting of text)	-	10000		10 % Discount for BIS samples
5.2(Message Readability)	-	10000		10 % Discount for BIS samples

19 Jul, 2027

-
-

139

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

Video Displays limited to 90"

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1.5(Components)	-	2000	Pre-tested certificates are analysed and reported 10% Discount for BIS
1.6(Power interface .)	-	5000	10% Discount for BIS
1.7(Markings and instructions)	-	5000	10% Discount for BIS
2.1(Protection from electric shock and energy hazards)	-	5000	10% Discount for BIS
2.2(SELV circuits)	-	5000	10% Discount for BIS
2.3(TNV circuits)	-	5000	10% Discount for BIS
2.4(Limited current circuits)	-	5000	10% Discount for BIS
2.5(Limited power sources .)	-	5000	10% Discount for BIS
2.6(Provisions for earthing and bonding)	-	10000	10% Discount for BIS
2.7(Overcurrent and earth fault protection in primary circuits)	-	5000	10% Discount for BIS
2.9(Electrical insulation)	-	5000	10% Discount for BIS
2.10(Clearances, creepage distances and distances through insulation)	-	5000	10% Discount for BIS
3.1(General)	-	5000	10% Discount for BIS
3.2(Connection to a mains supply)	-	5000	10% Discount for BIS
3.3(Wiring terminals for connection of external conductors)	-	5000	10% Discount for BIS
3.4(Disconnection from the mains supply)	-	5000	10% Discount for BIS
3.5(Interconnection of equipment)	-	5000	10% Discount for BIS
4.1(Stability)	-	5000	10% Discount for BIS
4.2(Mechanical strength)	-	5000	10% Discount for BIS
4.3(Design and construction)	-	5000	10% Discount for BIS
4.4(Protection against hazardous moving parts)	-	5000	10% Discount for BIS
4.5(Thermal requirements)	-	5000	10% Discount for BIS
4.6(Openings in enclosures)	-	2000	10% Discount for BIS
4.7(Resistance to fire)	-	5000	10% Discount for BIS
5.1(Touch current and protective conductor curren)	-	5000	10% Discount for BIS
5.2(Electric strength)	-	5000	10% Discount for BIS
5.3(Abnormal operating and fault conditions)	-	5000	10% Discount for BIS
6.1(Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment)	-	2000	10% Discount for BIS
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	4000	10% Discount for BIS
6.3(Protection of the telecommunication wiring system from overheating)	-	4000	10% Discount for BIS
7.1(General)	-	1000	10% Discount for BIS
7.2(Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment)	-	3000	10% Discount for BIS
7.3(Protection of equipment users from overvoltages on the cable distribution system)	-	3000	10% Discount for BIS
7.4(Insulation between primary circuits and cable distribution systems)	-	3000	10% Discount for BIS

19 Jul, 2027

-
-

140

IS 616 (2017)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

For TVs: Limited to 90” size

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and instructions)	-	2000	10% Discount for BIS
7(Heating under normal operating conditions)	-	10000	10% Discount for BIS
8(Constructional requirements with regard to the protection against electric shock)	-	5000	10% Discount for BIS
9(Electric shock hazard under normal operating conditions)	-	5000	10% Discount for BIS
10(Insulation requirements)	-	10000	10% Discount for BIS
11(Fault conditions)	-	5000	10% Discount for BIS
12(Mechanical strength)	-	15000	10% Discount for BIS
13(CLEARANCES and CREEPAGE DISTANCES)	-	5000	10% Discount for BIS
14(Components)	-	2000	10% Discount for BIS (Pre-tested/certified components are analysed while reporting for this clause)
15(TERMINALS)	-	5000	10% Discount for BIS
16(External flexible cords)	-	5000	10% Discount for BIS
17(Electrical connections and mechanical fixings)	-	5000	10% Discount for BIS
19(Stability and mechanical hazards)	-	5000	10% Discount for BIS
20(Resistance to fire)	-	10000	10% Discount for BIS

19 Jul, 2027

-
-

141

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

DC or AC Supplied Electronic Controlgear For LED Module

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	2000	10 % Discount for BIS samples
8(Protection against accidental contact with live parts)	-	2000	10 % Discount for BIS samples
9(Terminals)	-	2000	10 % Discount for BIS samples
10(PROVISION FOR EARTHING)	-	2000	10 % Discount for BIS samples
11(MOISTURE RESISTANCE)	-	10000	10 % Discount for BIS samples
12(Electric Strength)	-	5000	10 % Discount for BIS samples
13(Thermal endurance test for winding of ballasts)	-	10000	10 % Discount for BIS samples
14(Fault conditions)	-	5000	10 % Discount for BIS samples
15(Transformer heating)	-	2000	10 % Discount for BIS samples
16(Construction)	-	2000	10 % Discount for BIS samples
17(Creepage distance and clearances)	-	2000	10 % Discount for BIS samples
18(Screws, current carrying parts and connections)	-	2000	10 % Discount for BIS samples
19(Resistance to heat, fire and tracking)	-	5000	10 % Discount for BIS samples
20(Resistance to corrosion)	-	5000	10 % Discount for BIS samples

19 Jul, 2027

-
-

142

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

Restricted to cap type B22d, E14 and E27 only.

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	2000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
6(Interchangeability)	-	5000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
7(Protection against accidental contact with live parts)	-	2000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
8(Insulation Resistance and Electric Strength)	-	10000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
9(MECHANICAL STRENGTH)	-	2000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
10(cap temperature)	-	10000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
11(Resistance to Heat)	-	5000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
12(Resistance to Flame and Ignition)	-	5000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
13(Fault conditions)	-	3000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples
14(Creepage distance and clearances)	-	2000	Restricted to cap type B22d, E14 and E27 only. 10 % Discount for BIS samples

19 Jul, 2027

-
-

143

IS 16242 : Part 1 (2014)

Uninterruptible power systems (UPS): Part 1 general and safety requirements for UPS

Upto 10kV

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.6(Power interface)	-	5000	10 % Discount for BIS samples
4.7(Marking & instructions)	-	5000	10 % Discount for BIS samples
5.1(Protection against shock and energy hazards)	-	5000	10 % Discount for BIS samples
5.2(Requirement of auxiliary circuits)	-	5000	10 % Discount for BIS samples
5.3(Protective earthing and bonding)	-	5000	10 % Discount for BIS samples
5.4(AC and DC power isolation)	-	5000	10 % Discount for BIS samples
5.5(Over current and earth fault condition)	-	5000	10 % Discount for BIS samples
5.7(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	5000	10 % Discount for BIS samples
6.1(Wiring, connections and supply)	-	5000	10 % Discount for BIS samples
6.2(Connection to power)	-	5000	10 % Discount for BIS samples
6.3(Wiring terminals for external power conductors)	-	5000	10 % Discount for BIS samples
7.1(Enclosure)	-	5000	10 % Discount for BIS samples
7.2(STABILITY)	-	5000	10 % Discount for BIS samples
7.3(MECHANICAL STRENGTH)	-	5000	10 % Discount for BIS samples
7.4(Construction details)	-	5000	10 % Discount for BIS samples
7.5(Resistance to fire)	-	5000	10 % Discount for BIS samples
7.6(Battery location)	-	5000	10 % Discount for BIS samples
7.7(Temperature rise)	-	5000	10 % Discount for BIS samples
8.1(General procision for earth leakage)	-	5000	10 % Discount for BIS samples
8.2(Electric Strength)	-	5000	10 % Discount for BIS samples
8.3(Abnormal operating and fault conditions)	-	5000	10 % Discount for BIS samples
9.0(Connection to telecommunication networks)	-	5000	10 % Discount for BIS samples

19 Jul, 2027

-
-

144

IS 16046 : Part 2 (2018)

Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes ” Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for Use in Portable Applications Part 2 Lithium Systems ( Second Revision )

Restricted to Cell-5V, 10A & Batteries: 22V, 10A

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(General Safety Considerations)	-	4000	Cell: INR 65,000/- Battery: INR 75,000/- 10 % Discount for BIS samples
7(Specific requirements and tests)	-	70000	10 % Discount for BIS samples
8(Information for safety)	-	2000	10 % Discount for BIS samples
9(Marking)	-	2000	10 % Discount for BIS samples
10(Packaging)	-	2000	10 % Discount for BIS samples
4(Parameter Measurement Tolerances)	-	500	-
5.1(General)	-	500	-
5.2(Insulation and Wiring)	-	500	-
5.3(Venting)	-	500	-
5.4(Temperature, Voltage and Current Management)	-	500	-
5.5(Terminal Contacts)	-	500	-
5.6(Assembly of Cells into batteries)	-	500	-
5.7(Quality Plan)	-	500	-
5.8(Battery Safety Components)	-	500	-
6(Type Test and Sample Size)	-	500	-
7.1(Charging procedure for test purposes)	-	500	-
7.2(Intended Use)	-	500	-
7.3(Reasonably foreseeable misuse)	-	500	-
8.1(General)	-	500	-
8.2(Small Cell and battery safety information)	-	500	-
9.1(Cell Marking)	-	500	-
9.2(Battery Marking)	-	500	-
9.3(Caution for ingestion of small cells and batteries)	-	500	-
9.4(Other information)	-	500	-

19 Jul, 2027

-
Exclusion : Clause 7.3.1 of IS 16047: Part 3

145

IS 16046 : Part 1 (2018)

Restricted to Cell-5V, 10A & Batteries: 22V, 10A

90000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Packaging)	-	2000	Cell: INR 90,000/- Battery: INR 75,000/- 10 % Discount for BIS samples
7(Specific requirements and tests)	-	75000	10 % Discount for BIS samples
9(Marking)	-	4000	10 % Discount for BIS samples
8(Information for safety)	-	2000	10 % Discount for BIS samples
5(General Safety Considerations)	-	2000	10 % Discount for BIS samples
4(Parameter Measurement Tolerances)	-	500	10 % Discount for BIS samples
5.1(General)	-	500	10 % Discount for BIS samples
5.2(Insulation and Wiring)	-	2000	10 % Discount for BIS samples
5.3(Venting)	-	500	10 % Discount for BIS samples
5.4(Temperature, Voltage and Current Management)	-	500	10 % Discount for BIS samples
5.5(Terminal Contacts)	-	500	10 % Discount for BIS samples
5.6(Assembly of Cells into batteries)	-	500	10 % Discount for BIS samples
5.7(Quality Plan)	-	500	10 % Discount for BIS samples
6(Tyoe Test amd Sample Size)	-	500	10 % Discount for BIS samples
7.1(Charging procedure for test purposes)	-	500	10 % Discount for BIS samples
7.2(Intended Use)	-	500	10 % Discount for BIS samples
7.3(Reasonably foreseeable misuse)	-	500	10 % Discount for BIS samples
8.1(General)	-	500	10 % Discount for BIS samples
8.2(Small Cell and battery safety information)	-	500	10 % Discount for BIS samples
9.1(Cell Marking)	-	500	10 % Discount for BIS samples
9.2(Battery Marking)	-	500	10 % Discount for BIS samples

19 Jul, 2027

-
-

146

IS 302 : Part 2 : Sec 15 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 15 appliances for heating liquids (First Revision)

Upto 250V

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Classification)	-	100	-
7(Marking and instructions)	-	1000	-
8(Protection against live parts)	-	2000	-
10(POWER INPUT AND CURRENT)	-	2000	-
11(HEATING)	-	5000	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	5000	-
14(TRANSIENT OVERVOLTAGES)	-	10000	-
15(MOISTURE RESISTANCE)	-	5000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	5000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	5000	-
19(ABNORMAL OPERATION)	-	5000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	2000	-
21(MECHANICAL STRENGTH)	-	2000	-
22(CONSTRUCTION)	-	2000	-
23(INTERNAL WIRING)	-	2000	-
24(COMPONENTS)	-	2000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	2000	-
27(PROVISION FOR EARTHING)	-	2000	-
28(SCREWS AND CONNECTIONS)	-	2000	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
30(RESISTANCE TO HEAT AND FIRE)	-	5000	-
31(RESISTANCE TO RUSTING)	-	2000	-

19 Jul, 2027

-
Exclusion 32 (RADIATION, TOXICITY AND SIMILAR HAZARDS) (ABNORMAL OPERATION)

147

IS 10322 : Part 5 : Sec 6 (2013)

Luminaires: Part 5 particular requirements: Sec 6 handlamps

Handlamps

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	1000	-
5(Classification of Luminaires')	-	2000	-
6.0(Marking)	-	2000	-
8.2(Packing -Each Package shall bear the following Particulars)	-	200	-
7.0(Construction)	-	20000	-
8.0(Creepage Distance and Clearances)	-	5000	-
9.0(Provision for earthing)	-	2000	-
10.0(Terminals)	-	2000	-
11.0(External & Internal Wiring)	-	2000	-
12.0(Protection against electric shock)	-	2000	-
13.0(Endurance Tests and Thermal Tests)	-	8000	-
14.0(Resistance to Dust & Moisture)	-	2000	-
15.0(Insulation Resistance and Electric Strength)	-	2000	-
16.0(Resistance to Heat , fire and tracking)	-	5000	-

19 Jul, 2027

-
-

148

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

Rating up to 300V only

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	2000	-
5(Classification of Luminaires')	-	2000	-
6.0(Marking)	-	2000	-
7.0(Construction)	-	2000	-
8.0(Creepage Distance and Clearances)	-	5000	-
9.0(Provision for earthing)	-	2000	-
10.0(Terminals)	-	2000	-
11.0(External & Internal Wiring)	-	2000	-
12.0(Protection against electric shock)	-	5000	-
13.0(Endurance Tests and Thermal Tests)	-	15000	-
14.0(Resistance to Dust & Moisture)	-	5000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	5000	-

19 Jul, 2027

-
-

149

IS 10322 : Part 5 : Sec 7 (2017)

Luminaires: Part 5 particular requirements: Sec 7 lighting chains (First Revision)

LED Chain Lights

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
20.4(General Test Requireements)	-	1000	-
20.5(Classification of Luminaires')	-	2000	-
20.6(Marking)	-	2000	-
20.7(Construction)	-	2000	-
20.8(Creepage Distance and Clearances)	-	5000	-
20.10(Terminals)	-	2000	-
20.11(External & Internal Wiring)	-	2000	-
20.12(Protection against electric shock)	-	5000	-
20.13(Endurance Tests and Thermal Tests)	-	15000	-
20.14(Resistance to Dust & Moisture)	-	5000	-
20.15(Insulation Resistance and Electric Strength)	-	5000	-
20.16(Resistance to Heat , fire and tracking)	-	5000	-

19 Jul, 2027

-
-

150

IS 302 : Part 1 (2008)

Safety of household and similar electrical appliances: Part 1 general requirements (Sixth Revision)

AC/ DC Adapters for household and similar appliance

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	10% Discount for BIS
8.1.1(Protection against live parts in all positions)	-	2000	10% Discount for BIS
8.1.2(Protection against live parts in openings)	-	2000	10% Discount for BIS
8.1.3(Protection against live parts in visible glowing heating elements)	-	2000	10% Discount for BIS
8.1.4(Protection against live parts against protective impedance)	-	2000	10% Discount for BIS
10.1(Power input)	-	2000	10% Discount for BIS
10.2(Current input)	-	2000	10% Discount for BIS
11.1(General)	-	2000	10% Discount for BIS
11.2(General)	-	2000	10% Discount for BIS
11.3(Heating)	-	2000	10% Discount for BIS
13.1(General)	-	2000	10% Discount for BIS
13.2(Leakage current at operating temperature)	-	2000	10% Discount for BIS
13.3(Electric Strength at operating temperature)	-	2000	10% Discount for BIS
14(Transient Over Voltages)	-	10000	10% Discount for BIS
15.0(General)	-	2000	10% Discount for BIS
15.1(Ingress Protection test other than IPX0 (IP test))	-	5000	10% Discount for BIS
15.2(Spillage Test)	-	2000	10% Discount for BIS
15.3(Humidity Test)	-	5000	10% Discount for BIS
16.0(General)	-	2000	10% Discount for BIS
16.2(Leakage Current (after Clause 15))	-	2000	10% Discount for BIS
16.3(Electric Strength (after clause 15 and 16.2))	-	2000	10% Discount for BIS
17(Over Load Protection of Transformers and associated circuits)	-	5000	10% Discount for BIS
19(Abnormal Operation)	-	15000	10% Discount for BIS
20(Stability test)	-	2000	10% Discount for BIS
21(Mechanical Strength Test)	-	2000	10% Discount for BIS
22(Construction verification related test)	-	2000	10% Discount for BIS
23(General)	-	2000	10% Discount for BIS
25(Supply connection and external flexible cords)	-	2000	10% Discount for BIS
26(Terminals for external conductors)	-	2000	10% Discount for BIS
27(Provision for earthing)	-	2000	10% Discount for BIS
28(Screw test and connections)	-	2000	10% Discount for BIS
29(clearance, creepage distances and solid insulation)	-	2000	10% Discount for BIS
30.1(Ball pressure test)	-	2000	10% Discount for BIS
30.2(Glow Wire Test)	-	2000	10% Discount for BIS
30.2(Needle Flame Test)	-	2000	10% Discount for BIS
31(Resistance to Rusting)	-	5000	10% Discount for BIS

19 Jul, 2027

-
24 (Components) 19 (Abnormal Operation) 32 (Radiation Toxicity and Similar Hazards)

Bureau of Indian Standards

The National Standards Body of India

EMC Testing and Compliance LLP, Gurugram

115, Pace City-1, Sector 37, Gurugram, Gurugram, Haryana, 122001

8130427070 info@emclab.co.in

Scope List