BIS - LIMS (Laboratory Information Management System)

(suspended) Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

plot no.160,Industrial Area Phase-9, Sahibzada Ajit Singh Nagar, S.A.S Nagar, Punjab, 160062

9888717272 chandigarh@alphatesthouse.com

Scope List

Reset

285 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 1835 (1976)

Specification for round steel wire for ropes (Third Revision)

Bright wire, Galvanized wire, Type B, Type AB, Type A

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(Manufacturing )	-	25000	-
Cl 7(Workmanship)	-	25000	-
Cl 8(Manufacturing )	-	25000	-
Cl 10(Diameter)	-	25000	-
Cl 11.2(Workmanship)	-	25000	-
Cl 11.3(Coating Test)	-	25000	-
Cl 12.2(UTM)	-	25000	-
Cl 12.3(Torsion)	-	25000	-
Cl 12.4(Reverse Bend)	-	25000	-
Cl 12.5(Wrap)	-	25000	-
Cl 12.6(Adhesion )	-	25000	-
Cl. 5.1, T-1(C)	-	25000	-
Cl. 5.1, T-1(Mn)	-	25000	-
Cl. 5.1, T-1(Si)	-	25000	-
Cl. 5.1, T-1 ( Grade 1)(S)	-	25000	-
Cl. 5.1, T-1 ( Grade 2)(S)	-	25000	-
Cl. 5.1, T-1 ( Grade 3)(S)	-	25000	-
Cl. 5.1, T-1 ( Grade 4)(S)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(S)	-	25000	-
Cl. 5.1, T-1 ( Grade 1)(P)	-	25000	-
Cl. 9.1, T-3(Uniformity)	-	25000	-
Cl. 5.1, T-1 ( Grade 3)(P)	-	25000	-
Cl. 9.1, T-3(Mass of Zinc Coating)	-	25000	-
Cl. 5.1, T-1 ( Grade 4)(P)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(Cr)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(P)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(Cr)	-	25000	-
Cl. 5.1, T-1 ( Grade 1)(Cu)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(Cr)	-	25000	-
Cl. 5.1, T-1 ( Grade 2)(Cu)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(Cr)	-	25000	-
Cl. 5.1, T-1 ( Grade 3)(Cu)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(Cr)	-	25000	-
Cl. 5.1, T-1 ( Grade 4)(Cu)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(Ni)	-	25000	-
Cl. 5.1, T-1 ( Grade 1)(Ni)	-	25000	-
Cl. 5.1, T-1 ( Grade 4)(Ni)	-	25000	-
Cl. 5.1, T-1 ( Grade 3)(Ni)	-	25000	-
Cl. 5.1, T-1 ( Grade 2)(Ni)	-	25000	-
Cl. 5.1, T-1 ( Grade 5)(Cu)	-	25000	-

31 Dec, 2026

-
-

122

IS 2501 (1995)

Solid drawn copper tubesfor general engineering purposes - Specification (Third Revision)

Copper tubes

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.5(Grades)	-	6000	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No.6(CONDITION)	-	100	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 7(FREEDOM FROM DEFECTS)	-	100	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 8.1(Dimensions)	-	1500	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 8.2(Tolerances)	-	200	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 9(CHEMICAL COMPOSITION)	-	6000	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 10.1.1, Table no. 1(Tensile Test)	-	2500	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 10.2(Flattening and Doubling-Over Test)	-	1900	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 10.3(Drift Expanding Test)	-	2000	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 10.4(Non-Destructive Testing)	-	100	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 10.5("Microscopic Examination ( for 0 Condition Only )")	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No. 13(Marking)	-	100	Hydrogen Embrittlement Test. 5000/- extra charges.
10.6(Hydrogen Embrittlement Test)	-	0	Hydrogen Embrittlement Test. 5000/- extra charges.
Cl. No.5(Grades)	-	6000	-
Cl. No.6(CONDITION)	-	100	-
Cl. No. 7(FREEDOM FROM DEFECTS)	-	100	-
Cl. No. 8.1(Dimensions)	-	1500	-
Cl. No. 8.2(Tolerances)	-	200	-
Cl. No. 9(CHEMICAL COMPOSITION)	-	6000	-
Cl. No. 10.1.1, Table no. 1(Tensile Test)	-	2500	-
Cl. No. 10.2(Flattening and Doubling-Over Test)	-	1900	-
Cl. No. 10.3(Drift Expanding Test)	-	2000	-
Cl. No. 10.4(Non-Destructive Testing)	-	100	-
Cl. No. 10.5("Microscopic Examination ( for 0 Condition Only )")	-	500	-
Cl. No. 13(Marking)	-	100	-
10.6(Hydrogen Embrittlement Test)	-	0	-

31 Dec, 2026

-
Included w.e.f. 15.04.2024

123

IS 4412 (1981)

Specification for copper wires for general engineering purposes (First Revision)

Copper wires

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4(Chemical Composition)	-	10000	Hydrogen Embrittlement Test. 5000/- extra charges.
5.1(Tensile Test)	-	3500	Hydrogen Embrittlement Test. 5000/- extra charges.
5.2(Embrittlement Test)	-	0	Hydrogen Embrittlement Test. 5000/- extra charges.
6(Freedom from defect)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
7.1(Diameter and Tolerances)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Copper+Silver)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(phosphorus)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Antimony)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Arsenic)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Bismuth)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Iron)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Lead)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Nckel)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Selenium+Tellurium)	-	4000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Tellurium)	-	2000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Tin)	-	500	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 ( Table -1)(Total Impurities)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4(Chemical Composition)	-	10000	-
5.1(Tensile Test)	-	3500	-
5.2(Embrittlement Test)	-	0	-
6(Freedom from defect)	-	500	-
7.1(Diameter and Tolerances)	-	1000	-
Clause 4.1 ( Table -1)(Copper+Silver)	-	1000	-
Clause 4.1 ( Table -1)(phosphorus)	-	500	-
Clause 4.1 ( Table -1)(Antimony)	-	500	-
Clause 4.1 ( Table -1)(Arsenic)	-	500	-
Clause 4.1 ( Table -1)(Bismuth)	-	500	-
Clause 4.1 ( Table -1)(Iron)	-	500	-
Clause 4.1 ( Table -1)(Lead)	-	500	-
Clause 4.1 ( Table -1)(Nckel)	-	500	-
Clause 4.1 ( Table -1)(Selenium+Tellurium)	-	4000	-
Clause 4.1 ( Table -1)(Tellurium)	-	2000	-
Clause 4.1 ( Table -1)(Tin)	-	500	-
Clause 4.1 ( Table -1)(Total Impurities)	-	1000	-

31 Dec, 2026

-
Included w.e.f. 15.04.2024 Exclusion: Cl.5.2 (Embrittlement Test)

124

IS 4171 (1983)

Specification for copper rods and bars for general engineering purposes (First Revision)

Copper rods & bars

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 Table 1(1. Copper, including silver, min)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(2. Tin, max)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(3. Lead, max)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(5. Nickel, max)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(6. Arsenic, max)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(7. Antimony, max)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(8. Bismuth, max)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(9. Phosphorus)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(10. Selenium and Tellurium, max)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(11. Total impurities ( excluding silver, nickel and phosphorus ), max)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
5.2(Hydrogen Embrittlement test)	-	0	Hydrogen Embrittlement Test. 5000/- extra charges.
5.1(Tensile Properties)	-	4000	Hydrogen Embrittlement Test. 5000/- extra charges.
7.1(Dimension and Tolerances)	-	1000	Hydrogen Embrittlement Test. 5000/- extra charges.
Clause 4.1 Table 1(1. Copper, including silver, min)	-	1000	-
Clause 4.1 Table 1(2. Tin, max)	-	1000	-
Clause 4.1 Table 1(3. Lead, max)	-	1000	-
Clause 4.1 Table 1(5. Nickel, max)	-	1000	-
Clause 4.1 Table 1(6. Arsenic, max)	-	1000	-
Clause 4.1 Table 1(7. Antimony, max)	-	1000	-
Clause 4.1 Table 1(8. Bismuth, max)	-	1000	-
Clause 4.1 Table 1(9. Phosphorus)	-	1000	-
Clause 4.1 Table 1(10. Selenium and Tellurium, max)	-	1000	-
Clause 4.1 Table 1(11. Total impurities ( excluding silver, nickel and phosphorus ), max)	-	1000	-
5.2(Hydrogen Embrittlement test)	-	0	-
5.1(Tensile Properties)	-	4000	-
7.1(Dimension and Tolerances)	-	1000	-

31 Dec, 2026

-
-

125

IS 10773 (1995)

Wrought copper tubes for refrigeration and air - Conditioning purposes - Specification (First Revision)

Copper tubes

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Freedom from defect)	-	100	For Hydrogen Embrittlement Test 5000/- Extra charges.
8(Dimension and Tolerance)	-	1800	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Copper)	-	700	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Arsenic)	-	700	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Iron)	-	700	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Lead)	-	700	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Nickel)	-	700	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Tin)	-	700	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Phosphorus)	-	700	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Total impurities)	-	700	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Manganese)	-	100	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Aluminium)	-	100	For Hydrogen Embrittlement Test 5000/- Extra charges.
9.1 - 1(Zinc)	-	100	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.1.1 - 2(Tensile Test)	-	3000	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.1.1 - 2(0.2 Proof stress)	-	2300	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.1.1 - 2(Percentage elongation on 50mm gauge length)	-	500	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.2(Flattening Test)	-	2000	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.3(Drift Expanding Test)	-	2000	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.4.2(Hydrostatic Test)	-	200	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.4.3(Pneumatic Test)	-	200	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.4.1(Eddy Current Test)	-	200	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.5(Microscopic Examination)	-	200	For Hydrogen Embrittlement Test 5000/- Extra charges.
10.6(Hydrogen Embrittlement Test)	-	5000	For Hydrogen Embrittlement Test 5000/- Extra charges.
11.1(Residue Test Or cleanliness test)	-	1400	For Hydrogen Embrittlement Test 5000/- Extra charges.

31 Dec, 2026

-
-

126

IS 4386 (2022)

SPECIFICATION FOR PUTTING SHOTS Second Revision

WU18, WU20/SW, BU18, BU20, SM

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.2(Types)	-	8000	-
Cl.3.1(Material)	-	8000	-
Cl.3.2(Weight and Diameter)	-	8000	-
Cl.4(Manufacture, Workmanship and Finish)	-	8000	-
Cl.5(Test for Center of Gravity)	-	8000	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024

127

IS 5460 (2022)

SOFTBALL SPECIFICATION

Type 1, Type 2, Type 3

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1(Materials)	-	7500	-
Cl.4.1.2(Cover)	-	7500	-
Cl.4.1.3(Inks)	-	7500	-
Cl.4.2(Shape, Dimensions And Weight)	-	7500	-
Cl.5(Construction and Workmanship)	-	7500	-
Cl.6(Packing and Marking)	-	7500	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024

128

IS 12425 (2022)

SPECIFICATION FOR STEEPLECHASE HURDLES First Revision

Steeplechase Hurdles

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.2(Top Bar)	-	7500	-
Cl.2.1(Dimension)	-	7500	-
Cl.2.2(Mass)	-	7500	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024

129

IS 4630 (2022)

Indian Standard SPECIFICATION FOR BARBELL SET First Revision

BARBELL SET

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.2.1(Bars)	-	7500	-
Cl.2.2(Discs)	-	7500	-
Cl.2.3(Collar)	-	7500	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024

130

IS 4385 (2022)

SPECIFICATION FOR THROWING HAMMERS Second Revision

WU18, WU20/SW, BU18, BU20, SM

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Dimension)	-	7500	-
4.3(Weight)	-	7500	-
5.1(Test for center of gravity of Head)	-	7500	-
5.2(Handle Deformation Test)	-	7500	-
5.3(Breaking strength of Handle)	-	7500	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024

131

IS 415 (2022)

SHUTTLECOCKS SPECIFICATION

Grade 1 & Grade 2

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3(Classification)	-	7500	-
Cl.4(Material)	-	7500	-
Cl.5.1(Dimension)	-	7500	-
Cl.5.2(Weight)	-	7500	-
Cl.6.1(For Grade 1 Shuttlecock)	-	7500	-
Cl.6.2(For Grade 2 Shuttlecock)	-	7500	-
Cl.8.1(Pace and Flight)	-	7500	-
Cl.9(Packing and Marking)	-	7500	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024

132

IS 2463 (2022)

RING USED IN GYMNASTICS - SPECIFICATION

Rings used in Gymnastics

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Construction and Workmanship)	-	8000	-
Cl.5.1.1(Swing Rope)	-	8000	-
Cl.5.1.2(Tension Rope)	-	8000	-
Cl.5.1.3(Frame)	-	8000	-
Cl.5.1.4(Strap)	-	8000	-
Cl.5.1.5(Ring)	-	8000	-
Cl.5.2(Shape and Dimension)	-	8000	-
CL.6(Performance Requirement)	-	8000	-
Cl.4(Construction and Workmanship)	-	8000	-
Cl.5.1.1(Swing Rope)	-	8000	-
Cl.5.1.2(Tension Rope)	-	8000	-
Cl.5.1.3(Frame)	-	8000	-
Cl.5.1.4(Strap)	-	8000	-
Cl.5.1.5(Ring)	-	8000	-
Cl.5.2(Shape and Dimension)	-	8000	-
CL.6(Performance Requirement)	-	8000	-

31 Dec, 2026

-
-

133

IS 1865 (1991)

Iron castings with spheroidal or nodular graphite - Specification (Third Revision)

As per mentioned in the scope

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Grades)	-	15000	-
4.1(General requirements)	-	15000	-
5(Manufacture)	-	15000	-
6(Workmanship and finish)	-	15000	-
9(Micro structure)	-	15000	-
10.1(Separately-Cast Test Samples)	-	15000	-
12.1(Tensile Strength)	-	15000	-
12.2(Impact Test)	-	15000	-
13.1(Tensile Test)	-	15000	-
13.2(Hardness Test)	-	15000	-
13.3(Impact Test)	-	15000	-
14(Validity of tests)	-	15000	-
15(Retest)	-	15000	-

31 Dec, 2026

-
including w.e.f.09.10.2024

134

IS 7904 (2018)

High carbon steel wire rods - Specification (Second Revision)

Steel grades as mentioned in standard

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1,(Clauses 5.1 and 7.2)(S+P)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Nitrogen)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Titanium)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Vanadium)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Boron)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Copper)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Molybdenum)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Nickel)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Chromium)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Aluminium)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Silicon)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Manganese)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Phosphorous)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Sulphor)	-	10000	-
Table-1,(Clauses 5.1 and 7.2)(Carbon)	-	10000	-
Cl 9 (Dimensions & tolerances)()	-	10000	-
9(Dimesion (Diameter))	-	10000	-
9(Dimesion (Out of Roundness))	-	10000	-
10(Mechanical Properties (Tensile strength))	-	10000	-
10(Mechanical Properties (Reduction in Area))	-	10000	-
12(Surface Defects)	-	10000	-
13(Decarburization Test)	-	10000	-
TABLE 1 NOTE 1(Any Validated test method)	-	10000	-
TABLE 1 NOTE 1(By Calculation)	-	10000	-
TABLE 1 NOTE 6()	-	10000	-
TABLE 1 NOTE 1(Any Validated test method)	-	10000	-
TABLE 1 NOTE 1(By Calculation)	-	10000	-
TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu))	-	10000	-
TABLE 1 NOTE 1(Any Validated test method)	-	10000	-
TABLE 1 NOTE 1(By Calculation)	-	10000	-
TABLE 1 NOTE 6()	-	10000	-
TABLE 1 NOTE 1(Niobium)	-	10000	-
TABLE 1 NOTE 1(Micro Alloy Element (Nb+V+Ti))	-	10000	-
TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu))	-	10000	-
TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu))	-	10000	-

31 Dec, 2026

-
exclusion cl.14, cl 15, cl cl.16(optional tests)

135

IS 5872 (1990)

Cold rolled steel strips (Box Strappings) - Specification

COLD ROLLED STEEL STRIPS

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(UTM)	-	8000	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	8000	-
Cl 9(Workmanship)	-	8000	-
Cl 10(Width & Thickness)	-	8000	-
Cl 11(Workmanship)	-	8000	-
Cl 12(Coating)	-	8000	-
Cl 6(UTM)	-	8000	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	8000	-
Cl 9(Workmanship)	-	8000	-
Cl 10(Width & Thickness)	-	8000	-
Cl 11(Workmanship)	-	8000	-
Cl 12(Coating)	-	8000	-
Cl 6(UTM)	-	8000	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	8000	-
Cl 9(Workmanship)	-	8000	-
Cl 10(Width & Thickness)	-	8000	-
Cl 11(Workmanship)	-	8000	-
Cl 12(Coating)	-	8000	-
Cl. 10.2(Thickness)	-	8000	-
Cl. 6 Table 3(Elongation at 50 mm gauge length)	-	8000	-
Cl 12(Coating)	-	8000	-
Cl 11(Workmanship)	-	8000	-
Cl 10(Width & Thickness)	-	8000	-
Cl 9(Workmanship)	-	8000	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	8000	-
Cl 6(UTM)	-	8000	-
5(Chemical Composition)	-	8000	-
Cl 6(UTM)	-	8000	-
Cl 7(Bending To Both Side At 90°, Then Straight)	-	8000	-
Cl 9(Workmanship)	-	8000	-
Cl 10(Width & Thickness)	-	8000	-
Cl 11(Workmanship)	-	8000	-
Cl 12(Coating)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Carbon)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Manganese)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Sulphur)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Phosphorus)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Niobium)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Vanadium)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Titanium)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Boron)	-	8000	-
5.0 & 5.1 , Table 1 & 2(Micro Alloying Elements)	-	8000	-
6.0 & Table3(Tensile Strength - IS: 1608(P1))	-	8000	-
6.0 & Table3(Elongation on 50mm GL-IS: 1608(P1))	-	8000	-
10.0 & 10.2(Width -SOP MT-23)	-	8000	-
10.0 & 10.2(Thickness -SOP MT-23)	-	8000	-
11.0 & 11.1(Surface finish - Visual)	-	8000	-
12.0 & 12.1(Corrosion Resistance - IS 9844)	-	8000	-

31 Dec, 2026

-
including w.e.f.09.10.2024

136

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

MILD STEEL FOR METAL ARC WELDING ELECTRODES

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Workmanship)	-	11500	-
Cl 8 & 9(Diameter)	-	11500	-
Cl 7(Workmanship)	-	11500	-
Cl 8 & 9(Diameter)	-	11500	-
Cl 7(Workmanship)	-	11500	-
Cl 8 & 9(Diameter)	-	11500	-
6(Carbon %)	-	11500	-
6(Manganese %)	-	11500	-
6(Phosphorus %)	-	11500	-
6(Sulphur %)	-	11500	-
6(Silicon %)	-	11500	-
6( Copper %)	-	11500	-
6( Aluminium %)	-	11500	-
6( Nb)	-	11500	-
6(V)	-	11500	-
6( Ti)	-	11500	-
6(Cr)	-	11500	-
6(Mo)	-	11500	-
6(Ni)	-	11500	-
6(Cr+ Mo+ Ni)	-	11500	-
6(Carbon %)	-	11500	-
6(Manganese %)	-	11500	-
6(Phosphorus %)	-	11500	-
6(Sulphur %)	-	11500	-
6(Silicon %)	-	11500	-
6( Copper %)	-	11500	-
6( Aluminium %)	-	11500	-
6(V)	-	11500	-
6( Ti)	-	11500	-
6(Cr)	-	11500	-
6(Mo)	-	11500	-
6(Ni)	-	11500	-
6(Cr+ Mo+ Ni)	-	11500	-
6(Carbon %)	-	11500	-
6(Manganese %)	-	11500	-
6(Phosphorus %)	-	11500	-
6(Sulphur %)	-	11500	-
6(Silicon %)	-	11500	-
6( Copper %)	-	11500	-
6( Aluminium %)	-	11500	-
6( Nb)	-	11500	-
6(V)	-	11500	-
6( Ti)	-	11500	-
6(Cr)	-	11500	-
6(Mo)	-	11500	-
6(Ni)	-	11500	-
6(Cr+ Mo+ Ni)	-	11500	-
Cl. 9.2(Maximum Difference between 2 readings taken at any 2 diameters across cross section)	-	11500	-
Cl. 8,9(Width across flat)	-	11500	-
Cl. 8,9(Length)	-	11500	-
Cl. 5.2(Macro Examination)	-	11500	-
Cl 8 & 9(Diameter)	-	11500	-
Cl 7(Workmanship)	-	11500	-
Cl 7(Workmanship)	-	11500	-
Cl 8 & 9(Diameter)	-	11500	-
9.2 (a)(Width Across Flat)	-	11500	-
9.2 (b)(Diameter Difference)	-	11500	-
6( Nb)	-	11500	-

31 Dec, 2026

-
including w.e.f.09.10.2024

137

IS 1364 : Part 6 (2018)

Hexagon Head Bolts, Screws and Nuts of Product Grades A and B Part 6 Hexagon Nuts, Style 2 ( First Revision )

Hexagon Nuts, Style 2

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	25000	-
4, table 3(General requirements)	-	25000	-
4, table 3(Thread)	-	25000	-
4, table 3(Mechanical properties)	-	25000	-
4, table 3(Tolerances)	-	25000	-
4, table 3(Finish-coating)	-	25000	-
4, table 3(Surface integrity)	-	25000	-
4, table 3(Acceptability)	-	25000	-
5(Designation)	-	25000	-
3(Dimensions)	-	25000	-
4, table 3(General requirements)	-	25000	-
4, table 3(Thread)	-	25000	-
4, table 3(Mechanical properties)	-	25000	-
4, table 3(Tolerances)	-	25000	-
4, table 3(Finish-coating)	-	25000	-
4, table 3(Surface integrity)	-	25000	-
4, table 3(Acceptability)	-	25000	-
5(Designation)	-	25000	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024

138

IS 1367 : Part 13 (2020)

Technical Supply Conditions for Threaded Steel Fasteners Part 13 Hot Dip Galvanized Coatings on Threaded Fasteners ( Third Revision )

Hot Dip Galvanized Coatings on Threaded Fasteners

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Chemical Composition)	-	9000	-
7.0(Mechanical Propoerties ( Proof load & Tesnsile Strength))	-	9000	-
8.1(Appearance of zinc coating)	-	9000	-
8.3(Zinc coating thickness)	-	9000	-
8.4(Adhesion of Zinc Coating)	-	9000	-

31 Dec, 2026

-
including w.e.f.09.10.2024

139

IS 1367 : Part 6 (2018)

Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

Thin nuts Regular nuts and high nuts

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Material Testing)	-	9000	-
9.1(Proof Load)	-	9000	-
9.2(Hardness Test)	-	9000	-
9.3(Surface Integrity)	-	9000	-
Cl-4.3(Ranges of nominal diameters in relation to nut style and property class)	-	9000	-

31 Dec, 2026

-
-

140

IS 1367 : Part 3 (2017)

Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

Property class: 4.6 4.8 5.6 5.8 6.8 8.8 9.8 10.9 12.9

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Material Testing)	-	22000	-
7.0(Mechanical testing (Ys, TS, %EL, RA))	-	22000	-
9.6(Proof Load test for finished bolts scrwes, and studs)	-	22000	-
9.8(Head soundness test)	-	22000	-
9.9(Hardness Test)	-	22000	-
9.10(Decarburization test)	-	22000	-
9.11(Carburization test)	-	22000	-
9.12(Reducing of hardnes after retempering , Hv)	-	22000	-
9.13(Torsional Test)	-	22000	-
9.14(Impact Test)	-	22000	-
9.15(Surface discounity)	-	22000	-
6.0(Material Testing)	-	22000	-
7.0(Mechanical testing (Ys, TS, %EL, RA))	-	22000	-
9.6(Proof Load test for finished bolts scrwes, and studs)	-	22000	-
9.8(Head soundness test)	-	22000	-
9.9(Hardness Test)	-	22000	-
9.10(Decarburization test)	-	22000	-
9.11(Carburization test)	-	22000	-
9.12(Reducing of hardnes after retempering , Hv)	-	22000	-
9.13(Torsional Test)	-	22000	-
9.14(Impact Test)	-	22000	-
9.15(Surface discounity)	-	22000	-
6.0(Material Testing)	-	22000	-
7.0(Mechanical testing (Ys, TS, %EL, RA))	-	22000	-
9.6(Proof Load test for finished bolts scrwes, and studs)	-	22000	-
9.8(Head soundness test)	-	22000	-
9.9(Hardness Test)	-	22000	-
9.10(Decarburization test)	-	22000	-
9.11(Carburization test)	-	22000	-
9.12(Reducing of hardnes after retempering , Hv)	-	22000	-
9.13(Torsional Test)	-	22000	-
9.14(Impact Test)	-	22000	-
9.15(Surface discounity)	-	22000	-

31 Dec, 2026

-
including w.e.f.09.10.2024

141

IS 1117 (2018)

Laboratory glassware - Single - Volume pipettes (Second Revision)

Class-A and AS, Class-B

17800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1&3(Marking)	-	17800	-
3(Class of Accuracy)	-	17800	-
4.1(Nominal capacities)	-	17800	-
4.2(Accuracy)	-	17800	-
5.1(Material)	-	17800	-
5.1(Material)	-	17800	-
5.1.1(Limit of Alkalinity)	-	17800	-
5.2(Pattern of Pipette)	-	17800	-
5.3(Workmanship & Finish)	-	17800	-
5.4(i) Distance of graduation line from top of pipette.)	-	17800	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	17800	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	17800	-
5.4(iv) Wall thickness)	-	17800	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	17800	-
5.4(b) Other pipettes)	-	17800	-
5.4(v) Dia. of safety bulb (if provided ))	-	17800	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	17800	-
5.4(vii) Overall length, L)	-	17800	-
5.4(viii) Length of suction tube, L1 )	-	17800	-
5.4(ix) Length of delivery tube, L2 )	-	17800	-
5.4(x) Internal dia. of suction tube D1 )	-	17800	-
5.4(xi) External dia. of bulb D2 )	-	17800	-
5.4(xii) External dia. of delivery tube D3 )	-	17800	-
5.5(Delivery Time)	-	17800	-
5.5(Delivery Time)	-	17800	-
5.6&7(Graduation line & Visibility )	-	17800	-
6.1.2(Marking)	-	17800	-
6.1.1&3(Marking)	-	17800	-
3(Class of Accuracy)	-	17800	-
4.1(Nominal capacities)	-	17800	-
4.2(Accuracy)	-	17800	-
5.1(Material)	-	17800	-
5.1(Material)	-	17800	-
5.1.1(Limit of Alkalinity)	-	17800	-
5.2(Pattern of Pipette)	-	17800	-
5.3(Workmanship & Finish)	-	17800	-
5.4(i) Distance of graduation line from top of pipette.)	-	17800	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	17800	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	17800	-
5.4(iv) Wall thickness)	-	17800	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	17800	-
5.4(b) Other pipettes)	-	17800	-
5.4(v) Dia. of safety bulb (if provided ))	-	17800	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	17800	-
5.4(vii) Overall length, L)	-	17800	-
5.4(viii) Length of suction tube, L1 )	-	17800	-
5.4(ix) Length of delivery tube, L2 )	-	17800	-
5.4(x) Internal dia. of suction tube D1 )	-	17800	-
5.4(xi) External dia. of bulb D2 )	-	17800	-
5.4(xii) External dia. of delivery tube D3 )	-	17800	-
5.5(Delivery Time)	-	17800	-
5.5(Delivery Time)	-	17800	-
5.6&7(Graduation line & Visibility )	-	17800	-
6.1.2(Marking)	-	17800	-
6.1.1&3(Marking)	-	17800	-
3(Class of Accuracy)	-	17800	-
4.1(Nominal capacities)	-	17800	-
4.2(Accuracy)	-	17800	-
5.1(Material)	-	17800	-
5.1(Material)	-	17800	-
5.1.1(Limit of Alkalinity)	-	17800	-
5.2(Pattern of Pipette)	-	17800	-
5.3(Workmanship & Finish)	-	17800	-
5.4(i) Distance of graduation line from top of pipette.)	-	17800	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	17800	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	17800	-
5.4(iv) Wall thickness)	-	17800	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	17800	-
5.4(b) Other pipettes)	-	17800	-
5.4(v) Dia. of safety bulb (if provided ))	-	17800	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	17800	-
5.4(vii) Overall length, L)	-	17800	-
5.4(viii) Length of suction tube, L1 )	-	17800	-
5.4(ix) Length of delivery tube, L2 )	-	17800	-
5.4(x) Internal dia. of suction tube D1 )	-	17800	-
5.4(xi) External dia. of bulb D2 )	-	17800	-
5.4(xii) External dia. of delivery tube D3 )	-	17800	-
5.5(Delivery Time)	-	17800	-
5.5(Delivery Time)	-	17800	-
5.6&7(Graduation line & Visibility )	-	17800	-
6.1.2(Marking)	-	17800	-

31 Dec, 2026

-
Included w.e.f. 03.10.2024

142

IS 915 (2012)

Laboratory glassware - One - Mark volumetric flasks (Third Revision)

Class-A&B 1 to 5000 ml.

16200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Material)	-	1500	-
Table 1(Nominal Capacity)	-	1000	-
Table 1(Internal Neck Diameter)	-	500	-
Table 1(Distance of graduation line)	-	500	-
Table 1(Overall Height)	-	500	-
Table 1(Bulb Diameter)	-	500	-
Table 1(Base Diameter)	-	500	-
Table 1(Wall Thickness)	-	500	-
Table 1(Ground joint k4)	-	500	-
Table 1(Ground joint k6)	-	500	-
8.3(Shape)	-	500	-
8.4(Neck)	-	500	-
8.5(Stopper)	-	500	-
8.6(Dimensions)	-	2500	-
9.0(Graduation Line)	-	500	-
Table-2(Nominal capacity)	-	1000	-
Table-2(Internal neck diameter)	-	500	-
Table-2(Distance of graduation line 1))	-	500	-
Table-2(Overall height 2))	-	500	-
Table-2(Bulb diameter)	-	500	-
Table-2(Base diameter)	-	500	-
Table-2(Wall thickness)	-	500	-
Table-2(Ground joint 3) k4)	-	500	-
Table-2(Ground joint 3) k6)	-	500	-
12.1(Visibility of graduation line, figures and marking)	-	100	-
12.2(Visibility of graduation line, figures and marking)	-	100	-

31 Dec, 2026

-
including w.e.f.09.10.2024

143

IS 878 (2008)

Laboratory glassware - Graduated measuring cylinders (Second Revision)

5,10,25,50,100,250,500,1000,2000

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1(Nominal capacity)	-	500	-
Table-1(Overall height)	-	500	-
Table-1(Distance from top of scale to top of cylinder)	-	500	-
Table-1(Internal height to highest graduation line)	-	500	-
Table-1(Sub-divisions)	-	500	-
Table-1(capacity at lowest graduation line)	-	500	-
Cl-9.1(Wall thickness)	-	1000	-
Cl-9.2(Stability)	-	500	-
Cl-9.3(Base)	-	200	-
Cl-9.4(Rim and spout)	-	200	-
Cl-9.5(Neck and stopper)	-	200	-
Cl-9.6, Table-2(Nominal capacity)	-	2000	-
Cl-9.6, Table-2(Overall height)	-	2000	-
Cl-9.6, Table-2(Distance from top of scale to top of cylinder)	-	500	-
Cl-9.6, Table-2(Internal height to highest graduation line)	-	600	-
Cl-9.6, Table-2(Sub divisions)	-	200	-
Cl-9.6, Table-2(capacity at lowest graduation line)	-	500	-
Cl-10.1(Graduation)	-	1500	-
Cl-10.2(Figuring)	-	500	-
Cl-11(Accuracy testing)	-	1000	-
Cl-13(Visibility of graduation lines, figures and marking)	-	1000	-

31 Dec, 2026

-
-

144

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

a) Low-form Beakers b) Tall-form Beakers

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	1500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	1500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	2500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	1000	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	1000	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	1000	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	1000	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	1000	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	1000	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2500	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	1500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	1500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	2500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	1000	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	1000	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	1000	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	1000	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	1000	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	1000	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2500	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	1500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	1500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	2500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	1000	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	1000	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	1000	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	1000	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	1000	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	1000	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2500	-

31 Dec, 2026

-
-

145

IS 1381 : Part 1 (2003)

Laboratory glassware - Narrow - Necked boiling flasks (Second Revision)

25,50,100,250,500,1000,2000,3000,5000 ml.

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3, 4(Type of Flask)	-	1000	-
3.1, 4.1(Series of Nominal Capacity)	-	1000	-
3.2, 4.2(Nominal Capacity )	-	1000	-
3.3, 4.3(Material )	-	2000	-
3.4, 3.4.1 & 4.4, 4.4.1(Construction- a) Stability )	-	1000	-
3.4, 3.4.2 & 4.4, 4.4.2(Construction- b) Neck )	-	1000	-
3.5, 4.5(Dimensions (in mm) (Table 1&2))	-	1000	-
3.5.2(Neck Length)	-	1000	-
3.5.3, 4.5.2(Dimensions of base )	-	2000	-
3.5.4, 4.5.3(Wall thickness)	-	1000	-
5(Marking )	-	1000	-

31 Dec, 2026

-
-

146

IS 5484 (2023)

EC GRADE ALUMINIUM ROD PRODUCED BY CONTINUOUS CASTING AND ROLLING - SPECIFICATION

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Manufacture)	-	100	-
Cl-6.1(Grades and chemical composition of EC grade aluminium rod produced)	-	3000	-
Cl-6.2(Chemical analysis of the material)	-	3000	-
Cl-7.1(General condition for delivery and inspection relating)	-	50	-
Cl-9(Ultimate tensile strength and elongation)	-	3000	-
Cl-10.1(Resistivity)	-	1000	-
Cl-10.1(electrical conductivity)	-	1000	-
Cl-10.1.1(Resistivity and Conductivity Limit)	-	700	-
Cl-11(Dimensions)	-	300	-
Cl-13(Finish and freedom from defects)	-	100	-
Cl-14(Rejection and retest)	-	100	-
Cl-16(Marking)	-	50	-
CL 9(ULTIMATE TENSILE STRENGTH AND ELONGATION)	-	3000	-
CL 11(DIMENSIONS)	-	300	-
CL 13(FINISH AND FREEDOM FROM DEFECTS)	-	100	-
9(Elongation)	-	1000	-
12(Joint)	-	100	-

31 Dec, 2026

-
Included w.e.t. 09.09.2024

147

IS 7814 (2005)

Phosphor bronze sheet, strip and foil - Specification (Second Revision)

O,HA,HB,HD,HE,HS,HES

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4(Supply of material)	-	100	-
Clause 5("Freedom from defects")	-	200	-
Clause 7(chemical composition)	-	9000	-
Clause 8.1(Tensile test)	-	3000	-
Clause 8.2(Bend Test)	-	3000	-
Clause 9.1("Diameter of Strip and Foil")	-	2000	-
Clause 9.2(Thickness Tolerances)	-	500	-
Clause 9.3(Width Tolerance)	-	600	-
Clause 9.4("Length Tolerance for Sheet")	-	500	-
Clause 9.5("Permissible Maximum Value on Camber for Strip")	-	500	-
Clause 10("Sampling and criteria for conformity")	-	500	-
Clause 13(Marking)	-	100	-
Clause 4(Supply of material)	-	100	-
Clause 5("Freedom from defects")	-	200	-
Clause 7(chemical composition)	-	9000	-
Clause 8.1(Tensile test)	-	3000	-
Clause 8.2(Bend Test)	-	3000	-
Clause 9.1("Diameter of Strip and Foil")	-	2000	-
Clause 9.2(Thickness Tolerances)	-	500	-
Clause 9.3(Width Tolerance)	-	600	-
Clause 9.4("Length Tolerance for Sheet")	-	500	-
Clause 9.5("Permissible Maximum Value on Camber for Strip")	-	500	-
Clause 10("Sampling and criteria for conformity")	-	500	-
Clause 13(Marking)	-	100	-

31 Dec, 2026

-
Included w.e.f. 12.09.2024

148

IS 9612 (1980)

Specification for aluminium tubes for refrigeration purposes

19000,19500

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3(General Requirement)	-	100	-
Cl. No.4(Workmanship and finish)	-	500	-
Cl. No.5()	-	200	-
Cl. No.5()	-	200	-
Cl. No.6.1(Chemical composition)	-	9000	-
Cl. No.6.2(Tensile properties)	-	3500	-
Cl. No.6.3(Flattening Test)	-	3000	-
Cl. No.6.4(Pressure test requirement)	-	2000	-
Cl. No.7, Table no.1 and 2(Dimensions and tolerances)	-	1000	-
Cl. No.8(Retest)	-	450	-
Cl. No.9(Marking)	-	50	-

31 Dec, 2026

-
Included w.e.t. 09.09.2024

149

IS 15275 (2003)

Padlocks - Specification

DTP,LP,PTP PADLOCKS

24100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(SIZES AND GRADES OF PADLOCKS)	-	1500	-
5(SHAPE)	-	2000	-
Table 3 (i)(Key)	-	5000	-
Table 3 (ii)(Spring)	-	5000	-
Table 3 (iii)(Shackle)	-	5000	-
Table 3 (iv)(Case/Body)	-	5000	-
Table 4 (i)(Body and Plug)	-	5000	-
Table 4 (ii)(Disc Tumbler)	-	5000	-
Table 5(i)(Body and Plug)	-	5000	-
Table 5(ii)(Cylinder)	-	5000	-
Table 5(iii)(Pin Tumbler)	-	5000	-
Table 6 (i)(Body and Plug)	-	5000	-
Table 6 (ii)(Lever)	-	5000	-
Table 6 (iii)(Rivet)	-	5000	-
7.1.1(Solid Case)	-	3000	-
7.1.2(Laminated Case)	-	3000	-
7.1.3(Formed Case)	-	1000	-
7.2.2(Hardness of Shackles)	-	2000	-
8(Workmanship and finish)	-	6000	-
11(Marking)	-	500	-
12(Packing)	-	100	-

31 Dec, 2026

-
Included w.e.f. 12.09.2024

150

IS 723 (2023)

Steel Countersunk Head Wire Nails ï¿½ Specification ( Second Revision )

Nail 4 × 100 IS 723

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Dimensions & tolerances (Except 120° angle))	-	1000	-
4.2(Bend of shank)	-	1600	-
5(General requirements (Except Concentricity of head with the shank))	-	1000	-
6(Finish)	-	500	-
7(Bend test)	-	800	-
Cl.3(Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Aluminium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
4.1(Dimensions & tolerances (Except 120° angle))	-	1000	-
4.2(Bend of shank)	-	1600	-
5(General requirements (Except Concentricity of head with the shank))	-	1000	-
6(Finish)	-	500	-
7(Bend test)	-	800	-
Cl.3(Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	8000	-
Cl.3(Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Aluminium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-

31 Dec, 2026

-
Included w.e.f. 12.09.2024

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

(suspended) Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

plot no.160,Industrial Area Phase-9, Sahibzada Ajit Singh Nagar, S.A.S Nagar, Punjab, 160062

9888717272 chandigarh@alphatesthouse.com

Scope List