BIS - LIMS (Laboratory Information Management System)

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

plot no.160,Industrial Area Phase-9, Sahibzada Ajit Singh Nagar, S.A.S Nagar, Punjab, 160062

9888717272 chandigarh@alphatesthouse.com

Scope List

Reset

292 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

151

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

a) Low-form Beakers b) Tall-form Beakers

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	1500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	1500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	2500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	1000	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	1000	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	1000	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	1000	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	1000	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	1000	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2500	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	1500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	1500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	2500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	1000	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	1000	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	1000	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	1000	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	1000	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	1000	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2500	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	1500	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	1500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	2500	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	1000	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	1000	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	1000	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	1000	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	1000	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	1000	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2500	-

31 Dec, 2029

-
-

152

IS 1381 : Part 1 (2003)

Laboratory glassware - Narrow - Necked boiling flasks (Second Revision)

25,50,100,250,500,1000,2000,3000,5000 ml.

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3, 4(Type of Flask)	-	1000	-
3.1, 4.1(Series of Nominal Capacity)	-	1000	-
3.2, 4.2(Nominal Capacity )	-	1000	-
3.3, 4.3(Material )	-	2000	-
3.4, 3.4.1 & 4.4, 4.4.1(Construction- a) Stability )	-	1000	-
3.4, 3.4.2 & 4.4, 4.4.2(Construction- b) Neck )	-	1000	-
3.5, 4.5(Dimensions (in mm) (Table 1&2))	-	1000	-
3.5.2(Neck Length)	-	1000	-
3.5.3, 4.5.2(Dimensions of base )	-	2000	-
3.5.4, 4.5.3(Wall thickness)	-	1000	-
5(Marking )	-	1000	-

31 Dec, 2029

-
-

153

IS 5484 (2023)

EC GRADE ALUMINIUM ROD PRODUCED BY CONTINUOUS CASTING AND ROLLING - SPECIFICATION

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Manufacture)	-	100	-
Cl-6.1(Grades and chemical composition of EC grade aluminium rod produced)	-	3000	-
Cl-6.2(Chemical analysis of the material)	-	3000	-
Cl-7.1(General condition for delivery and inspection relating)	-	50	-
Cl-9(Ultimate tensile strength and elongation)	-	3000	-
Cl-10.1(Resistivity)	-	1000	-
Cl-10.1(electrical conductivity)	-	1000	-
Cl-10.1.1(Resistivity and Conductivity Limit)	-	700	-
Cl-11(Dimensions)	-	300	-
Cl-13(Finish and freedom from defects)	-	100	-
Cl-14(Rejection and retest)	-	100	-
Cl-16(Marking)	-	50	-
CL 9(ULTIMATE TENSILE STRENGTH AND ELONGATION)	-	3000	-
CL 11(DIMENSIONS)	-	300	-
CL 13(FINISH AND FREEDOM FROM DEFECTS)	-	100	-
9(Elongation)	-	1000	-
12(Joint)	-	100	-

31 Dec, 2029

-
Included w.e.t. 09.09.2024

154

IS 7814 (2005)

Phosphor bronze sheet, strip and foil - Specification (Second Revision)

O,HA,HB,HD,HE,HS,HES

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4(Supply of material)	-	100	-
Clause 5("Freedom from defects")	-	200	-
Clause 7(chemical composition)	-	9000	-
Clause 8.1(Tensile test)	-	3000	-
Clause 8.2(Bend Test)	-	3000	-
Clause 9.1("Diameter of Strip and Foil")	-	2000	-
Clause 9.2(Thickness Tolerances)	-	500	-
Clause 9.3(Width Tolerance)	-	600	-
Clause 9.4("Length Tolerance for Sheet")	-	500	-
Clause 9.5("Permissible Maximum Value on Camber for Strip")	-	500	-
Clause 10("Sampling and criteria for conformity")	-	500	-
Clause 13(Marking)	-	100	-
Clause 4(Supply of material)	-	100	-
Clause 5("Freedom from defects")	-	200	-
Clause 7(chemical composition)	-	9000	-
Clause 8.1(Tensile test)	-	3000	-
Clause 8.2(Bend Test)	-	3000	-
Clause 9.1("Diameter of Strip and Foil")	-	2000	-
Clause 9.2(Thickness Tolerances)	-	500	-
Clause 9.3(Width Tolerance)	-	600	-
Clause 9.4("Length Tolerance for Sheet")	-	500	-
Clause 9.5("Permissible Maximum Value on Camber for Strip")	-	500	-
Clause 10("Sampling and criteria for conformity")	-	500	-
Clause 13(Marking)	-	100	-

31 Dec, 2029

-
Included w.e.f. 12.09.2024

155

IS 9612 (1980)

Specification for aluminium tubes for refrigeration purposes

19000,19500

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3(General Requirement)	-	100	-
Cl. No.4(Workmanship and finish)	-	500	-
Cl. No.5()	-	200	-
Cl. No.5()	-	200	-
Cl. No.6.1(Chemical composition)	-	9000	-
Cl. No.6.2(Tensile properties)	-	3500	-
Cl. No.6.3(Flattening Test)	-	3000	-
Cl. No.6.4(Pressure test requirement)	-	2000	-
Cl. No.7, Table no.1 and 2(Dimensions and tolerances)	-	1000	-
Cl. No.8(Retest)	-	450	-
Cl. No.9(Marking)	-	50	-

31 Dec, 2029

-
Included w.e.t. 09.09.2024

156

IS 15275 (2003)

Padlocks - Specification

DTP,LP,PTP PADLOCKS

24100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(SIZES AND GRADES OF PADLOCKS)	-	1500	-
5(SHAPE)	-	2000	-
Table 3 (i)(Key)	-	5000	-
Table 3 (ii)(Spring)	-	5000	-
Table 3 (iii)(Shackle)	-	5000	-
Table 3 (iv)(Case/Body)	-	5000	-
Table 4 (i)(Body and Plug)	-	5000	-
Table 4 (ii)(Disc Tumbler)	-	5000	-
Table 5(i)(Body and Plug)	-	5000	-
Table 5(ii)(Cylinder)	-	5000	-
Table 5(iii)(Pin Tumbler)	-	5000	-
Table 6 (i)(Body and Plug)	-	5000	-
Table 6 (ii)(Lever)	-	5000	-
Table 6 (iii)(Rivet)	-	5000	-
7.1.1(Solid Case)	-	3000	-
7.1.2(Laminated Case)	-	3000	-
7.1.3(Formed Case)	-	1000	-
7.2.2(Hardness of Shackles)	-	2000	-
8(Workmanship and finish)	-	6000	-
11(Marking)	-	500	-
12(Packing)	-	100	-

31 Dec, 2029

-
Included w.e.f. 12.09.2024

157

IS 723 (2023)

Steel Countersunk Head Wire Nails ï¿½ Specification ( Second Revision )

Nail 4 × 100 IS 723

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Dimensions & tolerances (Except 120° angle))	-	1000	-
4.2(Bend of shank)	-	1600	-
5(General requirements (Except Concentricity of head with the shank))	-	1000	-
6(Finish)	-	500	-
7(Bend test)	-	800	-
Cl.3(Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Aluminium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
4.1(Dimensions & tolerances (Except 120° angle))	-	1000	-
4.2(Bend of shank)	-	1600	-
5(General requirements (Except Concentricity of head with the shank))	-	1000	-
6(Finish)	-	500	-
7(Bend test)	-	800	-
Cl.3(Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	8000	-
Cl.3(Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Aluminium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-
Cl.3(Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	800	-

31 Dec, 2029

-
Included w.e.f. 12.09.2024

158

IS 14811 (2000)

Rolled copper plate, sheet, strip and foils for general engineering purposes - Specification

O,HA,HB,HD

14150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.12(Calculation of mass)	-	200	-
Cl.11 Table-4(Preferred Inside Diameter)	-	200	-
Cl.11(Dimensions and tolerances)	-	1000	-
Cl.10(Hydrogen embrittlement test)	-	4000	-
Cl.9 table-3(Cupping test, erichsen value)	-	500	-
Cl.8.3 Table-2(Longitudinal Bend Test Angle, radius)	-	500	-
Cl.8.3 Table-2(Transverse Bend Test Angle, radius)	-	500	-
Cl.8.3(Bend test)	-	500	-
Cl.8.1 Table-1(Hardness)	-	500	-
Cl.8.1 Table-1(Elongation percent)	-	1000	-
Cl.8.1 Table-1(Tensile strength Mpa)	-	1500	-
Cl.8(Mechnical properties)	-	5000	-
Cl.7(Chemical composition)	-	4000	-
Cl.6(Freedom from defects)	-	100	-
Cl.12(Calculation of mass)	-	200	-
Cl.11 Table-4(Preferred Inside Diameter)	-	200	-
Cl.11(Dimensions and tolerances)	-	1000	-
Cl.10(Hydrogen embrittlement test)	-	4000	-
Cl.9 table-3(Cupping test, erichsen value)	-	500	-
Cl.8.3 Table-2(Longitudinal Bend Test Angle, radius)	-	500	-
Cl.8.3 Table-2(Transverse Bend Test Angle, radius)	-	500	-
Cl.8.3(Bend test)	-	500	-
Cl.8.1 Table-1(Hardness)	-	500	-
Cl.8.1 Table-1(Elongation percent)	-	1000	-
Cl.8.1 Table-1(Tensile strength Mpa)	-	1500	-
Cl.8(Mechnical properties)	-	5000	-
Cl.7(Chemical composition)	-	4000	-
Cl.6(Freedom from defects)	-	100	-

31 Dec, 2029

-
Included w.e.f. 12.09.2024

159

IS 17706 (2022)

PULL HANDLES SPECIFICATION

D- Shape, H-Shape, other Shape

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1(Materials)	-	3000	-
Clause 4.2(Fitting Accessories and Installation)	-	5000	-
Clause 4.4(Finish)	-	5000	-
Clause 5.1(Corrosion Resistance)	-	5750	-
Clause 5.2(Durability)	-	6000	-
Clause 6(Sampling and criteria for conformity)	-	100	-
Clause 7(Marking)	-	100	-
Clause 8(Packing)	-	50	-

31 Dec, 2029

-
Included w.e.t. 09.09.2024

160

IS 17876 (2022)

Stainless steel welded pipes and tubes for general service

Types- Pipes & Tubes

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	9200	-
10.1 (Table No.- 4)(Tensile Test,Mpa)	-	2000	-
11(Transverse Tension Test,%)	-	200	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	1000	-
13 (Table No.- 7)(Flange Test-IS 2330)	-	1500	-
14(Reverse Flattaning Test)	-	500	-
15(Flattaning Test-IS 2328)	-	500	-
16 (Table No.- 8)(Grain Size,No.-IS 4748)	-	1000	-
18(Leak Tighteness Test)	-	3500	-
19("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	2500	-
20(Eddy current test, Air under water test ,Radiographic tests)	-	0	-
22(Workmanship, Finish and Appearance)	-	100	-
23(Repair by Welding or Grinding)	-	200	-
24 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	2000	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	2000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	600	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	600	-
"Clause 19 IS 10461(Part 1)"(Corrosion Test)	-	2500	-
Clause 10.1 - Table 4(Tensile Strength)	-	2000	-
Clause 10.1 - Table 4(Yield Strength)	-	1000	-
Clause 10.1 - Table 4(Percent Elongation)	-	1000	-
Clause 11(Transverse Tension Test)	-	200	-
Clause 12(Hardness Test)	-	1000	-
Clause 13(Flange Test)	-	1500	-
Clause 14(Reverse Flattening Test)	-	500	-
Clause 15(Flattening Test)	-	500	-
Clause 16(Grain Size)	-	1000	-
Clause 18()	-	2500	-
"Clause 19 IS 10461(Part 2)"(Corrosion Test)	-	2500	-
Clause 22(Workmanship, Finish & Appearance)	-	100	-
Clause 24 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	2000	-
8.1 & 8.2 (Table No.- 1)(Vanadium (V))	-	200	-
8.1 & 8.2 (Table No.- 1)(Tungstun (W))	-	200	-
8.1 & 8.2 (Table No.- 1)(Tantalum (Ta))	-	200	-
12.2(Hardness test)	-	1000	-
17(Sampling)	-	100	-
25(Marking)	-	100	-
6.7, Table 7, ii)(c) Chromium VI)	-	600	-

31 Dec, 2029

-
Included w.e.f 22.04.2024 Exclusion: Cl.20 (Eddy current test, air under water test, radiographic tests)

161

IS 916 (2000)

Square tins for solid products - Specification (Fourth Revision)

Square tins for solid products

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Capacity)	-	1000	-
4.2(Dimension and Tolerances)	-	1700	-
4.3.1(Nominal Thickness)	-	500	-
4.3.1(Material of electrolytic tinplate)	-	1000	-
4.3.1.1(Tin Coating Thickness)	-	1000	-
4.3.2(Handle wire diameter)	-	300	-
4.3.2(Handle wire material)	-	1000	-
4.3.3(Solder Tin content)	-	1000	-
4.3.3(Solder Antimony content)	-	500	-
4.4.1(Body)	-	500	-
4.4.2(Sides)	-	500	-
4.4.3(Top and Bottom)	-	500	-
4.4.4(Top and Bottom embossing)	-	500	-
4.4.5(Handle)	-	500	-
4.4.6(Closure)	-	500	-
4.4.7(Supply condition)	-	500	-
4.4.8(Internal Finish)	-	1000	-
4.4.9(External Treatment)	-	500	-
5.1(Air-Pressure Test)	-	3000	-
5.2(Handle Pull Test)	-	3000	-

31 Dec, 2029

-
Included w.e.t. 09.09.2024

162

IS 10325 (2000)

Square tins - 15 kg/litre for ghee, vanaspati, edible oils and bakery shortenings - Specification (Second Revision)

Square tins - 15 kg/litre for ghee

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Dimensions and Tolerances)	-	1000	-
4.2.1.1(Dimensions and Tolerances )	-	500	-
4.1(Dimensions and Tolerances)	-	500	-
4.1(Dimensions and Tolerances)	-	500	-
4.1(Dimensions and Tolerances)	-	500	-
4.2.1(Material)	-	2500	-
4.2.1(Material)	-	2500	-
4.2.2(Handle)	-	400	-
4.3.1 (Manufacture)	-	300	-
4.3.2(Manufacture)	-	300	-
4.3.3(Manufacture)	-	300	-
4.3.4(Manufacture)	-	300	-
4.3.5(Handle)	-	500	-
4.3.5(Handle)	-	500	-
4.3.5(Handle)	-	500	-
4.3.5(Handle)	-	500	-
4.3.5(Handle)	-	500	-
5.1(Air-Pressure Test)	-	4000	-
5.2(Handle Pull Test)	-	4000	-
5.3(Hydraulic Pressure Test)	-	3400	-
Cl. 4.3.7,(Internal Finish)	-	500	-
Cl. 4.3.8.(Outside Finish)	-	500	-

31 Dec, 2029

-
-

163

IS 13801 (2013)

Chequered Cement Concrete Tiles -

200,250,300,400 MM

7300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	500	-
Cl 12.1(Concavity & Convexity )	-	200	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	200	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	200	-
Cl 12.4(Water absorption)	-	500	-
Cl 12.5(Wet transverse strength)	-	1500	-
Cl 12.6(Resistance to wear)	-	2500	-
Cl 11(Finish)	-	100	-
Annex G3.1(Aluminium oxide content)	-	1500	-
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	500	-
Cl 12.1(Concavity & Convexity )	-	200	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	200	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	200	-
Cl 12.4(Water absorption)	-	500	-
Cl 12.5(Wet transverse strength)	-	1500	-
Cl 12.6(Resistance to wear)	-	2500	-
Cl 11(Finish)	-	100	-
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	200	-
Cl 12.1(Concavity & Convexity )	-	200	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	200	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	200	-
Cl 12.4(Water absorption)	-	500	-
Cl 12.5(Wet transverse strength)	-	1500	-
Cl 12.6(Resistance to wear)	-	2500	-
Cl 11(Finish)	-	100	-
Cl 11(Finish)	-	100	-
Cl 12.6(Resistance to wear)	-	2500	-
Cl 12.5(Wet transverse strength)	-	1500	-
Cl 12.4(Water absorption)	-	500	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	200	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	200	-
Cl 12.1(Concavity & Convexity )	-	200	-
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	500	-
8.3(Thickness of wearing layer)	-	100	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024

164

IS 18513 (2023)

Hot-Dip Zinc- Aluminium-Magnesium Alloy Coated Steel Sheets Plates and Strips - Specification

Hot-Dip Zinc- Aluminium-Magnesium Alloy Coated Steel Sh

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 5.4(Surface Finish)	-	2500	-
Clause. 7.0(Material)	-	6000	-
Clause. 8.0(Coating Adherence)	-	2000	-
Clause. 8.0(Coating Mass)	-	3000	-
Clause. 10.0(Tensile Test)	-	1500	-
Clause. 10.0(Yield Stress or Proof stress)	-	1500	-
Clause. 10.0(Elongation)	-	1000	-
Clause. 10.0(Plastic strain Ratio)	-	1000	-
Clause. 10.0(Tensile Strain Hardening Component)	-	1500	-
Clause. 10.0(Bake Hardening Index)	-	1000	-
Clause. 10.0(Hardness Test)	-	1000	-
Clause. 10.0(Bend Test)	-	1000	-
Clause.11.0(Dimensions, Shape & Tolerances)	-	1500	-
Clause. 5.4(Surface Finish)	-	2500	-
Clause. 7.0(Material)	-	6000	-
Clause. 8.0(Coating Adherence)	-	2000	-
Clause. 8.0(Coating Mass)	-	3000	-
Clause. 10.0(Tensile Test)	-	1500	-
Clause. 10.0(Yield Stress or Proof stress)	-	1500	-
Clause. 10.0(Elongation)	-	1000	-
Clause. 10.0(Plastic strain Ratio)	-	1000	-
Clause. 10.0(Tensile Strain Hardening Component)	-	1500	-
Clause. 10.0(Bake Hardening Index)	-	1000	-
Clause. 10.0(Hardness Test)	-	1000	-
Clause. 10.0(Bend Test)	-	1000	-
Clause.11.0(Dimensions, Shape & Tolerances)	-	1500	-
7(C)	-	300	-
7(Mn)	-	300	-
7(P)	-	300	-
7(S)	-	300	-
7(Si)	-	300	-
7(N)	-	2100	-
7(Cr)	-	300	-
7(Mo)	-	300	-
7(Ni)	-	300	-
7(Al)	-	300	-
7(B)	-	300	-
7(Ti)	-	300	-
7(V)	-	300	-
7(Nb)	-	300	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024

165

IS 18316 (2023)

HOT ROLLED AND COLD ROLLED STEEL STRIPS INTENDED FOR PROCESSING OF SEMIFULLY PROCESSED NON-GRAIN ORIENTED ELECTRICAL STEEL OR FULLY PROCESSED GRAIN ORIENTED ELECTRICAL STEEL SPECIFICATION

Low, Medium , High, very high silicon

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 7.0(Carbon)	-	1000	-
Clause. 7.0(Silicon)	-	1000	-
Clause. 7.0(Sulphur)	-	1000	-
Clause. 7.0(Phosphorus)	-	1000	-
Clause. 7.0(Manganese)	-	1000	-
Clause. 7.0(Aluminium)	-	2000	-
Clause.8.0(Freedom From Defects)	-	500	-
Clause.9.0(Dimensions, Shape & Tolerances (for Hot-rolled Steel))	-	2500	-
Clause.10.0(Dimensions, Shape & Tolerances (for Cold-rolled Steel))	-	1000	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024

166

IS 617 (2024)

Aluminium and Aluminium Alloys Ingots for Remelting and Castings for General Engineering Purposes â Specification (Fourth Revision)

Aluminium and Aluminium Alloys Ingots.

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1, Table-1(Si)	-	500	-
Cl-6.1, Table-1(Fe)	-	500	-
Cl-6.1, Table-1(Cu)	-	500	-
Cl-6.1, Table-1(Mn)	-	500	-
Cl-6.1, Table-1(Mg)	-	500	-
Cl-6.1, Table-1(Cr)	-	500	-
Cl-6.1, Table-1(Ni)	-	500	-
Cl-6.1, Table-1(Zn)	-	500	-
Cl-6.1, Table-1(Pb)	-	500	-
Cl-6.1, Table-1(Sn)	-	500	-
Cl-6.1, Table-1(Ti)	-	500	-
Cl-6.1, Table-1(Others elements Each)	-	1500	-
Cl-6.1, Table-1(Others elements Total)	-	1500	-
Cl-6.1, Table-1(Aluminium)	-	500	-
Cl-6.2(The chemical analysis)	-	13100	-
Cl-7.1, Table-2(Sand-Cast Alloys- Tensile Strength)	-	1000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Proof Stress)	-	1000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Elongation)	-	500	-
Cl-7.1, Table-2(Sand-Cast Alloys- Brinell Hardness HBW)	-	1000	-
Cl-7.1, Table-3(Chill Cast Alloys- Tensile Strength)	-	1000	-
Cl-7.1, Table-3(Chill Cast Alloys- Proof Stress)	-	1000	-
Cl-7.1, Table-3(Chill Cast Alloys- Elongation)	-	500	-
Cl-7.1, Table-3(Chill Cast Alloys- Brinell Hardness HBW)	-	1000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Tensile Strength)	-	1000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Proof Stress)	-	1000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Elongation)	-	500	-
Cl-7.1, Table-4(Investment-Cast Alloys-Brinell Hardness)	-	1000	-
Cl-7.2(Tensile Tests)	-	1000	-
Cl-7.3(Test Pieces)	-	100	-
Cl-7.4(Hardness)	-	1000	-
Cl-8(Freedom from Defects)	-	100	-
Cl-11(RETEST)	-	100	-
Cl-13(Marking)	-	100	-
Cl. 6(Silicon)	-	500	-
Cl. 6(Iron)	-	500	-
Cl. 6(Copper)	-	500	-
Cl. 6(Manganese)	-	500	-
Cl. 6(Magnesium)	-	500	-
Cl. 6(Chromium)	-	500	-
Cl. 6(Nickel)	-	500	-
Cl. 6(Zinc)	-	500	-
Cl. 6(Lead)	-	500	-
Cl. 6(Tin)	-	500	-
Cl. 6(Titanium)	-	500	-
Cl. 6(Others Element Each)	-	1500	-
Cl. 6(Others Element Total)	-	1500	-
Cl. 6(Aluminium)	-	500	-
Cl. 6(Silver)	-	500	-
Cl. 6(Zirconium)	-	600	-
Cl. 6(Titanium+Zirconium)	-	1000	-
Cl. 6(Antimony)	-	500	-
Cl. 6(Cobalt)	-	500	-
Cl. 6(Antimony+Cobalt)	-	1000	-
Cl. 6(Beryllium)	-	500	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024

167

IS 1545 (1994)

Solid drawn coppbr and copper alloy tubes for condensers and heat exchangers - Specification (Third Revision)

Solid Drawn copper and copper alloy tubes

19800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.5(GRADES)	-	7100	-
Cl. No.6(CONDITION)	-	100	-
Cl. No.7(FREEDOM FROM DEFECTS)	-	100	-
Cl. No.8.1(Dimensions)	-	1000	-
Cl. No.8.2(Tolerances)	-	200	-
Cl. No.9.1, Table no.1(i)(Chemical composition-Copper)	-	500	-
Cl. No.9.1, Table no.1(ii)(Lead)	-	1000	-
Cl. No.9.1, Table no.1(iii)(Tin)	-	100	-
Cl. No.9.1, Table no.1(iv)(Iron)	-	1000	-
Cl. No.9.1, Table no.1(v)(Aluminium)	-	100	-
Cl. No.9.1, Table no.1(vi)(Mangenese)	-	1000	-
Cl. No.9.1, Table no.1(vi)(Arsenic)	-	100	-
Cl. No.9.1, Table no.1(vii)(Nickle)	-	1000	-
Cl. No.9.1, Table no.1(iv)(Zinc)	-	1000	-
Cl. No.9.1, Table no.1(iv)(Phosphorus)	-	300	-
Cl. No.9.1, Table no.1(iv)(T.L)	-	1000	-
Cl. No.10.1.1(Hardness test)	-	1800	-
Cl. No.10.1.2(Tensile Test)	-	3400	-
Cl. No.10.2, Table no.2(Flattening Test)	-	1500	-
Cl. No.10.3(Drift Expanding Test)	-	1800	-
Cl. No.10.4.1(Eddy-Current Test)	-	200	-
Cl. No.10.4.2(Hydrostatic Test)	-	200	-
Cl. No.10.4.3(Pneumatic Test ( Alternative to Hydrostatic Test)	-	200	-
Cl. No.10.5(Microscopic Examination)	-	1000	-
Cl. No.10.6.1(Ammonia Vapour Cracking Test)	-	100	-
Cl. No.10.6.2(Mercurous Nitrate Test)	-	1000	-
Cl. No.13(Marking)	-	100	-

31 Dec, 2029

-
Included w.e.f. 12.04.2024

168

IS 18297 (2023)

Cabinet Hinges

Full overlay, Half overlay, Inset

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Type & Size)	-	200	-
4.1(Type (a) Full Overlay (Fig-1))	-	200	-
4.2((b) Half Overlay (Fig-2))	-	200	-
4.1((b) Half Overlay (Fig-2))	-	200	-
4.1(c) Inset (Fig-2))	-	200	-
4.2(Size (Fig-2))	-	200	-
4.3(Manufacture & Purchaser)	-	200	-
5(Material (IS 18297))	-	2000	-
6 Table 1(Manufacture(IS: 18297))	-	1000	-
7.1(General Test Requirement (IS: 18297))	-	1000	-
7.1.1(Preparatory Measures (IS:18297))	-	1000	-
7.1.2(Limiting Deviations (IS:18297))	-	500	-
7.1.3(Application of Force (IS: 18297))	-	1000	-
7.1.4(Sequence of Testing (IS 18297))	-	1000	-
7.1.5.1(Mass (IS:18297))	-	500	-
7.1.5.2((i) Face withdrawal of Screws (IS: 2380 P-14))	-	500	-
7.1.5.2((ii) Density (IS 2380 P-3))	-	500	-
7.2(Over Load Test (IS 18297))	-	1000	-
7.2.1(Overload Test - Vertical Static overload test)	-	1000	-
7.2.2(Overload Test - Horizontal Static overload test)	-	1000	-
Cabinet Hinges(Functional Test (IS: 18297))	-	1000	-
Cabinet Hinges(Functional Test (IS: 18297))	-	1000	-
7.3.2(First Vertical Static Load test (IS 18297))	-	1000	-
7.3.3(First Horizontal Static Load test (IS 18297))	-	2000	-
7.3.4(Slam shut test (IS 18297))	-	1000	-
7.3.6(Durability Test (IS 18297))	-	1000	-
7.3.7(Deflection Test (IS 18297))	-	1000	-
7.3.8(Second Vertical Static Test (IS 18297))	-	1000	-
7.3.9(Second Horizontal Static Test (IS: 18297))	-	1000	-
7.4(Crrosion Resistance (IS 18297))	-	1500	-
7.5(Finish (IS: 18297))	-	100	-
7.3.1(Operating Forces)	-	100	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024

169

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

Cement Concrete Flooring Tiles

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	1000	-
Cl 12.2(Concavity & Convexity )	-	1000	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	1000	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	1000	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	1900	-
Cl 12.7(Resistance to wear)	-	3000	-
Cl 11(Suface Finish)	-	100	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	1000	-
Cl 12.2(Concavity & Convexity )	-	1000	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	1000	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	1000	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	1900	-
Cl 12.7(Resistance to wear)	-	3000	-
Cl 11(Suface Finish)	-	100	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	1000	-
Cl 12.2(Concavity & Convexity )	-	1000	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	1000	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	1000	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	1900	-
Cl 12.7(Resistance to wear)	-	3000	-
Cl 11(Suface Finish)	-	100	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	1000	-
Cl 12.2(Concavity & Convexity )	-	1000	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	1000	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	1000	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	1900	-
Cl 12.7(Resistance to wear)	-	3000	-
Cl 11(Suface Finish)	-	100	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	1000	-
Cl 12.2(Concavity & Convexity )	-	1000	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	1000	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	1000	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	1900	-
Cl 12.7(Resistance to wear)	-	3000	-
Cl 11(Suface Finish)	-	100	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	1000	-
Cl 12.2(Concavity & Convexity )	-	1000	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	1000	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	1000	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.6(Wet transverse strength )	-	1900	-
Cl 12.7(Resistance to wear)	-	3000	-
Cl 11(Suface Finish)	-	100	-
Cl 11(Suface Finish)	-	100	-
Cl 12.7(Resistance to wear)	-	3000	-
Cl 12.6(Wet transverse strength )	-	1900	-
Cl 12.5(Water absorption)	-	1000	-
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	1000	-
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	1000	-
Cl 12.2(Concavity & Convexity )	-	1000	-
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	1000	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024

170

IS 1469 (1993)

Ferromolybdenum - Specification (Fourth Revision)

High , Medium, Low carbon

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause-6(Supply of Materials)	-	500	-
Clause-7.1(Constitution of Consignment)	-	500	-
Clause-8.1(Mo)	-	5000	-
Clause-8.1(C, Max)	-	1000	-
Clause-8.1(Si, Max)	-	1000	-
Clause-8.1(S, Max)	-	1000	-
Clause-8.1(P Max)	-	1000	-
Clause-8.1(Du Max)	-	1000	-
Clause-8.1(Al Max)	-	0	-
Clause-8.1(Pb Max)	-	0	-
Clause-8.1(Sn Max)	-	0	-
Clause-8.4(Established instrumental/chemical method)	-	0	-
Clause-9(Size Range)	-	500	-
Clause-12(Marking)	-	500	-
Clause-6(Supply of Materials)	-	500	-
Clause-7.1(Constitution of Consignment)	-	500	-
Clause-8.1(Mo)	-	5000	-
Clause-8.1(C, Max)	-	1000	-
Clause-8.1(Si, Max)	-	1000	-
Clause-8.1(S, Max)	-	1000	-
Clause-8.1(P Max)	-	1000	-
Clause-8.1(Du Max)	-	1000	-
Clause-8.1(Al Max)	-	0	-
Clause-8.1(Pb Max)	-	0	-
Clause-8.1(Sn Max)	-	0	-
Clause-8.4(Established instrumental/chemical method)	-	0	-
Clause-9(Size Range)	-	500	-
Clause-12(Marking)	-	500	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024 Exclusion: Clause-8.1 (Al Max, PB Max, SN Max), Clause-8.4 (Established instrumental/chemical method)

171

IS 1466 (1985)

Specification for ferrovanadium (Third Revision)

Specification for ferrovanadium

10200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause-2.1(Ferro Vanadium)	-	100	-
Clause-3(Grades)	-	200	-
Clause-4(Supply of Material)	-	200	-
Clause-5(Chemical Composition)	-	9000	-
Clause-6(Norminal size Ranges)	-	500	-
Clause-9(Marking)	-	200	-
Clause-2.1(Ferro Vanadium)	-	100	-
Clause-3(Grades)	-	300	-
Clause-4(Supply of Material)	-	200	-
Clause-5(Chemical Composition)	-	8800	-
Clause-6(Norminal size Ranges)	-	500	-
Clause-9(Marking)	-	200	-
3 & 5(V)	-	3000	-
3 & 5(Si)	-	1000	-
3 & 5(C)	-	1000	-
3 & 5(S)	-	1000	-
3 & 5(P)	-	1000	-
3 & 5(Al)	-	1000	-
3 & 5(Mn)	-	1000	-
3 & 5(Cr)	-	0	-
3 & 5(Cu)	-	0	-
3 & 5(Ni)	-	0	-
3 & 5(Pb)	-	0	-
3 & 5(Sn)	-	0	-
3 & 5(Zn)	-	0	-
3 & 5(Mo)	-	0	-
3 & 5(Ti)	-	0	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024 Exclusion: Cl.3 & 5 (Chromium, copper, nickel, Lead, Tin, Zinc, molybdenum, Titanium

172

IS 18384 (2023)

Hot-Rolled Steel Strip, Sheet and Plates for Welded Steel Pipe for Pipeline Transportation Systems ï¿½ Specification

PSL-1,2

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.8.1, 8.2, 8.4, table 2, table 3(Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Chromium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Nickel- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Molybdenum- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Vanadium- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Niobium- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Titanium- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Nb+V Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Nb+V+Ti Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(others-- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	100	-
Cl.8.1, 8.2, 8.4, table 2, table 3(CEPcm- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.8.1, 8.2, 8.4, table 2, table 3(CEIIW - Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Chromium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Nickel- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Molybdenum- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Vanadium- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Niobium- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Titanium- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Nb+V Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(Nb+V+Ti Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.8.1, 8.2, 8.4, table 2, table 3(others-- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.8.1, 8.2, 8.4, table 2, table 3(CEPcm- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.8.1, 8.2, 8.4, table 2, table 3(CEIIW - Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
9(Yield Strength)	-	1500	-
9(Tensile Strength)	-	1500	-
9(Plastic Strain Ratio)	-	1500	-
9(Elongation)	-	500	-
10(Bend Test)	-	1000	-
11(Hardnes Test)	-	1000	-
12(CVN Impact Test)	-	1000	-
13(DWT Test)	-	1000	-
17(Dimensions)	-	500	-
18(Tolerances)	-	500	-

31 Dec, 2029

-
Included w.e.f. 25.07.2024

173

IS 410 (1977)

Specification for cold rolled brass sheet, strip and foil (Third Revision)

CuZn30,37,40

15800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Freedom from defects)	-	100	-
6.1 Table-1(Cu)	-	1000	-
6.1 Table-1(Pb)	-	1000	-
6.1 Table-1(Fe)	-	1000	-
6.1 Table-1(Total impurities including iron)	-	2500	-
6.1 Table-1(Zn)	-	1000	-
7.1.1(Tensile Test)	-	2000	-
Table-2(Thickness)	-	100	-
Table-2(Tensile Strength)	-	2000	-
Table-2(Elongation)	-	1000	-
Table-2(Vickers Hardness)	-	700	-
Table-2(Transverse Bend)	-	1000	-
Table-2(Longitudinal Bend)	-	1000	-
7.1.1(Erichsen cupping values -IS 410)	-	800	-
7.1.5(Grain Size - IS 410)	-	1500	-
8(Dimensions -IS 410)	-	1000	-
11(Marking)	-	100	-

31 Dec, 2029

-
Included w.e.f. 02.07.2024

174

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

Billets ,slabs, blooms

7900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 7.1(CARBON)	-	1000	10000/- Rs. Extra for Optional test.
Clause - 7.1(SULPHUR)	-	1000	10000/- Rs. Extra for Optional test.
Clause - 7.1(PHOSPHURS)	-	1000	10000/- Rs. Extra for Optional test.
Clause - 7.1(MANGANESE)	-	1000	10000/- Rs. Extra for Optional test.
Clause - 7.1(NITROGEN)	-	1500	10000/- Rs. Extra for Optional test.
As per Clause 10(Dimension)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 10.1(Dimension Width)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 10.1(Dimension Thickness)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 10.2(Dimension Length)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 11.5(Bend)	-	150	10000/- Rs. Extra for Optional test.
As per Clause 11.6(Camber)	-	100	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (i)(Out of Square)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (ii)(Round Corners)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	100	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	100	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 11.7 (ix)(Scarfing pits)	-	50	10000/- Rs. Extra for Optional test.
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	50	10000/- Rs. Extra for Optional test.
Clause. 13(Macro examination test.)	-	3500	10000/- Rs. Extra for Optional test.
Clause. 13(Macro examination test.)	-	3500	10000/- Rs. Extra for Optional test.
Clause. 13(Sulphur print.)	-	3500	10000/- Rs. Extra for Optional test.
Clause. 13(Inclusion content)	-	3000	10000/- Rs. Extra for Optional test.
Clause. 14(Marking)	-	0	10000/- Rs. Extra for Optional test.
Clause.15(Ordering information)	-	300	10000/- Rs. Extra for Optional test.
Clause.6.0(Manufacture)	-	0	10000/- Rs. Extra for Optional test.
Clause.7.1(Silicon)	-	1000	10000/- Rs. Extra for Optional test.
Clause.7.1(Carbon Equbalant)	-	1200	10000/- Rs. Extra for Optional test.
Clause.7.1(Microalloy element)	-	100	10000/- Rs. Extra for Optional test.

31 Dec, 2029

-
Included w.e.f. 19.04.2024.

175

IS 10577 (1982)

Specification for lancing pipes

Light/Medium/Heavy

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 .1 Table 1,2,3(Dimensions)	-	200	-
6 .1 Table 1,2,3( 1) Outside diameter )	-	200	-
6 .1 Table 1,2,3(2) Thickness,mm)	-	200	-
7 Table 1,2,3( 2)Mass,kg/m)	-	200	-
6 .1 Table 4(3)Socket dimension)	-	200	-
6 .1 Table 4( i)OD,mm)	-	200	-
6 .1 Table 4( ii)Length.mm)	-	200	-
12.1(12. HYDRAULIC TEST)	-	3500	-
13.0(13. TEST ON FINISHED PIPES AND SOCKETS)	-	200	-
13.2(i)Tensile strength,, Mpa Min)	-	2000	-
13.2(ii)Elongation,% Min)	-	1000	-
13.1(Bend Test)	-	1500	-
13.4( Expansion Test on Sockets)	-	1500	-
13.4.1( 1)Drift Expanding Test)	-	1500	-
13.4.2( ii)Taper Screw Plug irest)	-	900	-
14.1(Workmanship)	-	100	-
18.0(Coating )	-	1500	-
6 .1 Table 1,2,3(Dimensions)	-	200	-
6 .1 Table 1,2,3( 1) Outside diameter )	-	200	-
6 .1 Table 1,2,3(2) Thickness,mm)	-	200	-
7 Table 1,2,3( 2)Mass,kg/m)	-	200	-
6 .1 Table 4(3)Socket dimension)	-	200	-
6 .1 Table 4( i)OD,mm)	-	200	-
6 .1 Table 4( ii)Length.mm)	-	200	-
12.1(12. HYDRAULIC TEST)	-	3500	-
13.0(13. TEST ON FINISHED PIPES AND SOCKETS)	-	200	-
13.2(i)Tensile strength,, Mpa Min)	-	2000	-
13.2(ii)Elongation,% Min)	-	1000	-
13.1(Bend Test)	-	1500	-
13.4( Expansion Test on Sockets)	-	1500	-
13.4.1( 1)Drift Expanding Test)	-	1500	-
13.4.2( ii)Taper Screw Plug irest)	-	900	-
14.1(Workmanship)	-	100	-
18.0(Coating )	-	1500	-
6 .1 Table 1,2,3(Dimensions)	-	200	-
6 .1 Table 1,2,3( 1) Outside diameter )	-	200	-
6 .1 Table 1,2,3(2) Thickness,mm)	-	200	-
7 Table 1,2,3( 2)Mass,kg/m)	-	200	-
6 .1 Table 4(3)Socket dimension)	-	200	-
6 .1 Table 4( i)OD,mm)	-	200	-
6 .1 Table 4( ii)Length.mm)	-	200	-
12.1(12. HYDRAULIC TEST)	-	3500	-
13.0(13. TEST ON FINISHED PIPES AND SOCKETS)	-	200	-
13.2(i)Tensile strength,, Mpa Min)	-	2000	-
13.2(ii)Elongation,% Min)	-	1000	-
13.1(Bend Test)	-	1500	-
13.4( Expansion Test on Sockets)	-	1500	-
13.4.1( 1)Drift Expanding Test)	-	1500	-
13.4.2( ii)Taper Screw Plug irest)	-	900	-
14.1(Workmanship)	-	100	-
18.0(Coating )	-	1500	-
6 .1 Table 1,2,3(Dimensions)	-	200	-
6 .1 Table 1,2,3( 1) Outside diameter )	-	200	-
6 .1 Table 1,2,3(2) Thickness,mm)	-	200	-
7 Table 1,2,3( 2)Mass,kg/m)	-	200	-
6 .1 Table 4(3)Socket dimension)	-	200	-
6 .1 Table 4( i)OD,mm)	-	200	-
6 .1 Table 4( ii)Length.mm)	-	200	-
12.1(12. HYDRAULIC TEST)	-	3500	-
13.0(13. TEST ON FINISHED PIPES AND SOCKETS)	-	200	-
13.2(i)Tensile strength,, Mpa Min)	-	2000	-
13.2(ii)Elongation,% Min)	-	1000	-
13.1(Bend Test)	-	1500	-
13.4( Expansion Test on Sockets)	-	1500	-
13.4.1( 1)Drift Expanding Test)	-	1500	-
13.4.2( ii)Taper Screw Plug irest)	-	900	-
14.1(Workmanship)	-	100	-
18.0(Coating )	-	1500	-

31 Dec, 2029

-
Included w.e.f. 02.07.2024.

176

IS 292 (1983)

Specification for leaded brass ingots and casting (Second Revision)

LCB-1,2

10150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3.1, Table no.1(Chemical composition)	-	5000	-
Cl. No.3.2(General compostion)	-	5000	-
Cl. No.4(pressure test)	-	4000	-
Cl. No.5(Freedom from defect)	-	100	-
Cl. No.6(Size and shape)	-	1000	-
Cl. No.7(Marking)	-	50	-
Cl.3.1(Copper+ incidental nickel -IS 3685)	-	1000	-
Cl.3.1(Lead - IS 3685)	-	800	-
Cl.3.1(Iron -IS 3685)	-	800	-
Cl.3.1(Aluminium - IS 3685)	-	800	-
Cl.3.1(Zinc - IS 3685)	-	800	-
Cl.3.1(Tin - IS 3685)	-	800	-
5(FREEDOM FROM DEFECTS)	-	100	-
6(Shape & size)	-	1000	-
Cl. No.3.1, Table no.1(Chemical composition)	-	5000	-
Cl. No.3.2(General compostion)	-	5000	-
Cl. No.4(pressure test)	-	4000	-
Cl. No.5(Freedom from defect)	-	100	-
Cl. No.6(Size and shape)	-	1000	-
Cl. No.7(Marking)	-	50	-
Cl.3.1(Copper+ incidental nickel -IS 3685)	-	1000	-
Cl.3.1(Lead - IS 3685)	-	800	-
Cl.3.1(Iron -IS 3685)	-	800	-
Cl.3.1(Aluminium - IS 3685)	-	800	-
Cl.3.1(Zinc - IS 3685)	-	800	-
Cl.3.1(Tin - IS 3685)	-	800	-
5(FREEDOM FROM DEFECTS)	-	100	-
6(Shape & size)	-	1000	-

31 Dec, 2029

-
Included w.e.f. 02.07.2024.

177

IS 3748 (2022)

Tool Steels - Specification

Tool Steels

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.4(Shape, dimensions and tolerances)	-	200	-
7.2(Chemical Composition)	-	4900	-
7.2(Carbon)	-	200	-
7.2(Silicon)	-	200	-
7.2(Manganese)	-	200	-
7.2(Nickel)	-	200	-
7.2(Chromium)	-	200	-
7.2(Molybdenum)	-	200	-
7.2(Sulphur)	-	200	-
7.2(Phosphorus)	-	200	-
7.2(Nitrogen)	-	1500	-
7.2(Copper)	-	200	-
7.2(Aluminium)	-	200	-
7.2(Titanium)	-	200	-
7.2(Niobium)	-	200	-
7.2(Cerium)	-	200	-
7.2(Tantalum)	-	200	-
7.2(Cobalt)	-	200	-
7.2(Tungsten)	-	200	-
7.2(Vanadium)	-	200	-
7.3(Surface Quality)	-	200	-
7.4(Shapes, dimensions and tolerances)	-	200	-
7.2(Hardness Test)	-	1000	-
Annex B.3(Verification of Minimum Hardness in Hardening Test)	-	500	-
Annex B.7(Non-Destructive Test)	-	1000	-
As per Clause 7.2, Table 2 to 9(Carbon)	-	200	-
As per Clause 7.2, Table 2 to 9(Silicon)	-	200	-
As per Clause 7.2, Table 2 to 9(Manganese)	-	200	-
As per Clause 7.2, Table 2 to 9(Chromium)	-	200	-
As per Clause 7.2, Table 2 to 9(Sulphur)	-	200	-
As per Clause 7.2, Table 2 to 9(phosphorus)	-	200	-
As per Clause 7.2, Table 2 to 9(Cobalt)	-	200	-
As per Clause 7.2, Table 2 to 9(Molybdenum)	-	200	-
As per Clause 7.2, Table 2 to 9(vanadium)	-	200	-
As per Clause 7.2, Table 2 to 9(Tunsten)	-	200	-
As per Clause 7.2, Table 2 to 9(Nickel)	-	200	-
As per Clause 7.2, Table 2 to 9(Nitrogen)	-	1500	-
4.1(Classification)	-	200	-
4.2(Designation)	-	200	-
6.2.1(General)	-	100	-
6.2.2(Heat-treatment condition)	-	200	-
6.2.3(Surface Condition)	-	200	-
7.1(General requirements)	-	50	-
7.2(Chemical composition and mechanical properties)	-	8200	-
7.3(Surface quality)	-	200	-
7.4(Shape, dimensions and tolerances)	-	200	-
9(Marking)	-	50	-
11.1(Product diameter or thickness ≥ 15 mm)	-	100	-
11.2(Product diameter or thickness < 15 mm)	-	100	-

31 Dec, 2029

-
Included w.e.f. 11.06.2024

178

IS 2590 (1987)

Specification for primary aluminium ingots for remelting for general engineering purposes (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General requirements )	-	1500	-
4(Manufacture )	-	100	-
5(Grades)	-	100	-
6.1(Chemical composition )	-	14500	-
7.1(Shapes and sizes)	-	100	-
9(Marking)	-	100	-
Table-1, Clause - 6.1.1(Copper)	-	1000	-
Table-1, Clause - 6.1.1(Iron)	-	1000	-
Table-1, Clause - 6.1.1(Magnesium)	-	1000	-
Table-1, Clause - 6.1.1(Manganese)	-	1500	-
Table-1, Clause - 6.1.1(Titanium + Vanadium)	-	1500	-
Table-1, Clause - 6.1.1(Silicon)	-	1500	-
Table-1, Clause - 6.1.1(Vanadium)	-	1500	-
Table-1, Clause - 6.1.1(Zinc)	-	1500	-
Table-1, Clause - 6.1.1(Other elements (each))	-	1000	-
Table-1, Clause - 6.1.1(Others Total)	-	1000	-
Table-1, Clause - 6.1.1(Aluminium)	-	2000	-
3.1(General requirements )	-	1500	-
4(Manufacture )	-	1000	-
5(Grades)	-	5000	-
6.1(Chemical composition )	-	5000	-
7.1(Shapes and sizes)	-	1500	-
9(Marking)	-	1000	-
Table-1, Clause - 6.1.1(Copper)	-	300	-
Table-1, Clause - 6.1.1(Iron)	-	300	-
Table-1, Clause - 6.1.1(Magnesium)	-	300	-
Table-1, Clause - 6.1.1(Manganese)	-	300	-
Table-1, Clause - 6.1.1(Titanium + Vanadium)	-	600	-
Table-1, Clause - 6.1.1(Silicon)	-	300	-
Table-1, Clause - 6.1.1(Vanadium)	-	300	-
Table-1, Clause - 6.1.1(Zinc)	-	300	-
Table-1, Clause - 6.1.1(Other elements (each))	-	1000	-
Table-1, Clause - 6.1.1(Others Total)	-	1000	-
Table-1, Clause - 6.1.1(Aluminium)	-	300	-

31 Dec, 2029

-
Included w.e.f. 03.04.2024

179

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

1,2,3,4,5

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(S)	-	1000	-
4(P)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.00 to 2.24 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2.80 to 3.15 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Hard Core For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Hard Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 For 2.00 to 2.24 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.80 to 3.15 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Soft Core)	-	2000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Soft Core)	-	2000	-
11(a) Size)	-	100	-
11(b) Construction)	-	500	-
11(c) tensile designation)	-	200	-
11(d) lay)	-	100	-
11(e) coating)	-	200	-
11(f) length)	-	200	-
11( g) mass)	-	200	-
11(h) manufacturer's name or trade mark)	-	50	-
11(i) lot number along with the order number)	-	50	-
11(j) BIS Standards Mark)	-	50	-
5(a) Grade)	-	100	-
5(b) Tensile Grade)	-	200	-
6(a) Lay)	-	100	-
6(b) Construction)	-	500	-
7(Freedom from defects)	-	100	-
9(a) Tensile)	-	2000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
11(a) Size)	-	100	-
11(b) Construction)	-	500	-
11(c) tensile designation)	-	200	-
11(e) coating)	-	200	-
11(f) length)	-	200	-
11( g) mass)	-	200	-
11(h) manufacturer's name or trade mark)	-	50	-
11(i) lot number along with the order number)	-	50	-
11(j) BIS Standards Mark)	-	50	-
5(a) Grade)	-	100	-
5(b) Tensile Grade)	-	200	-
6(a) Lay)	-	100	-
6(b) Construction)	-	500	-
7(Freedom from defects)	-	50	-
9(a) Tensile)	-	2000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
11(a) Size)	-	100	-
11(b) Construction)	-	500	-
11(c) tensile designation)	-	200	-
11(d) lay)	-	100	-
11(e) coating)	-	200	-
11(f) length)	-	200	-
11( g) mass)	-	200	-
11(h) manufacturer's name or trade mark)	-	50	-
11(i) lot number along with the order number)	-	50	-
11(j) BIS Standards Mark)	-	50	-
5(a) Grade)	-	100	-
5(b) Tensile Grade)	-	200	-
6(a) Lay)	-	100	-
6(b) Construction)	-	500	-
7(Freedom from defects)	-	50	-
9(a) Tensile)	-	2000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
11(d) lay)	-	100	-

31 Dec, 2029

-
-

180

IS 1897 (2008)

Copper strip for electrical purposes - Specification (Third Revision)

Copper strip

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(SUPPLY OF MATERIAL)	-	100	-
CLAUSE 6(CHEMICAL COMPOSITION)	-	7000	-
CLAUSE 8(MECHANICAL PROPERTIES)	-	2500	-
CLAUSE 8.2(Bend Test)	-	500	-
CLAUSE 9(ELECTRICAL RESISTIVITY TEST)	-	3000	-
CLAUSE 10(TEST FOR CONTROLLED PROOF RESISTANCE (OPTIONAL))	-	0	-
CLAUSE 11(DlMENSIONS AND TOLERANCES)	-	1900	-
CLAUSE 13(RETEST)	-	0	-

31 Dec, 2029

-
Included w.e.f. 12.04.2024

First
Prev
5
6
7
8
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

plot no.160,Industrial Area Phase-9, Sahibzada Ajit Singh Nagar, S.A.S Nagar, Punjab, 160062

9888717272 chandigarh@alphatesthouse.com

Scope List