BIS - LIMS (Laboratory Information Management System)

BIS, Patna Branch Laboratory (PBL)

Bureau of Indian Standards, Patliputra Industrial Estate, Patna - 800013, Patna, Patna, Bihar, 800013

- pbol@bis.gov.in

Scope List

Reset

96 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 16715 (2018)

Ultrafine Ground Granulated Blast Furnace Slag - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4 and 5.1 (Manganese oxide (MnO))	-
Clause 4 and 5.1 (Magnesium oxide (MgO))	-
Clause 4 and 5.1 (Sulphide sulphur (S))	-
Clause 4 and 5.1 (Sulphate (as SO3),)	-
Clause 4 and 5.1 (Insoluble residue)	-
Clause 4 and 5.1 (Chloride content)	-
Clause 4 and 5.1 (Loss on ignition)	-
Clause 4 and 5.1 ((CaO+MgO+1/3AlO3)/( SiO2 +2/3 AlO3))	-
Clause 4 and 5.1 ((CaO+MgO+Al2O3)/ SiO2)	-
Clause 4 and 5.1 ((CaO+CaS+1/2 MgO+Al2O3)/ (SiO2+ MnO))	-

Partial

IS 16714 (2018)

Ground granulated blast furnace slag for use in cement, mortar and concrete - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 5.1 (Manganese oxide (MnO))	-
Clause 5.1 (Magnesium oxide (MgO))	-
Clause 5.1 (Sulphide sulphur (S))	-
Clause 5.1 (Insoluble residue)	-
Clause 5.1 (Chloride content)	-
Clause 5.1 (Loss on ignition)	-
Clause 5.1 ((CaO+MgO+1/3AlO3)/( SiO2 +2/3 AlO3))	-
Clause 5.1 ((CaO+MgO+Al2O3)/ SiO2)	-
Clause 5.1 ((CaO+CaS+1/2 MgO+Al2O3)/ (SiO2+ MnO))	-

Partial

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 Table 1 (Classification of pipes)	-
7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes: Mean outside Diameter)	-
7.1,7.1.1 IS 12235 (Part 1) Table 2 (Outside Diameter at any point)	-
7.1.2 IS 12235 (Part 1) Table 2 (Wall Thickness )	-
7.1.3 (Effective length)	-
8 (Pipe Ends)	-
9 (PHYSICAL AND CHEMICAL CHARACTERISTICS)	-
9.1 (Visual Appearance)	-
9.1 (Visual Appearance)	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2) (Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-
9.5 IS 12235(Part 2) (Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-
9.6 IS 12235(Part 14) (Density)	-
10.5 IS 12235(Part 13) (Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-

Partial

IS 8035 (2022)

HANDPUMP- SHALLOW WELL- SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause-4.1.1 (Bright bars, used in the pump production)	-
Clause-4.1.3 (Linear/angular dimensions)	-
Clause-4.1.2 (Unmachined dimensions)	-
Clause-4.2 (Castings Grade FG)	-
Clause-4.3 (Steel plates/sheets)	-
Clause-4.4 (Plunger rod)	-
Clause-4.5 (Spring washer)	-
Clause-4.6 (Bolts and nuts)	-
Clause-4.7 (High-density polyethylene)	-
Clause-4.8 (Flexible PVC)	-
Clause-4.9 (Circlip)	-
Clause-4.10 (Rubber gasket)	-
Clause-5.1.1 (Electro Galvanizing)	-
Clause-5.1.2 (All bolts, nuts, washers)	-
Clause-5.2.1 (Hot-dip galvanized)	-
Clause-6 (Visual Tests)	-
Clause-6.3 (Routine Test)	-
Clause-6.4 (Criteria of Conformity)	-
Clause-8 (Marking)	-

Partial

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 7.1.1 (General Quality)	-
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-
Clause 7.1.3 (Colour and Texture)	-
Clause 6.3 (Bonding and Delamination between the layers of paver blocks)	-
7.2- TABLE-2- (i) IS-15658 (Annex-B) (Average Width -Higher)	-
7.2- TABLE-2- (i) IS-15658 (Annex-B) (Individual Width - Higher)	-
7.2- TABLE-2- (i) IS-15658 (Annex-B) (Average Width -Lower)	-
7.2- TABLE-2- (i) IS-15658 (Annex-B) (Individual Width - Lower)	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v) (Arris/chamfer, Width)	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v) (Indivdual Arris/chamfer, Width)	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v) (Arris/chamfer, Depth)	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v) (Indivdual Arris/chamfer, Depth)	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi) (Thickness of wearing Layer)	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi) (Indivdual Thickness of wearing Layer)	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii) (Plan Area (Asp))	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii) (Indivdual Plan Area (Asp))	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii) (Ratio of wearing face area and Plan area (Asw/Asp))	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii) (Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix) (Deviation from squareness)	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a) ( Indivdual Water absorption)	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b) (Water absorption (Average of three test specimens))	-

Partial

IS 2202 : Part 1 (2023)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Seventh Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (GRADE)	-
4 (TYPE)	-
5 (SIZES)	-
9.1 (WORKMANSHIP AND FINISH)	-
9.2 (WORKMANSHIP AND FINISH)	-
9.3 (WORKMANSHIP AND FINISH)	-
11.1 (Dimensions - Height)	-
11.1 (Dimensions - Width)	-
11.1 (Dimensions - Thickness)	-
11.1 (Dimensions - Variation in thickness)	-
11.1 (Dimensions - Squareness)	-
11.12 (End immersion test)	-
11.13 (Knife Test)	-
11.14 (Glue Adhesion Test)	-

Partial

IS 15895 (2018)

High alumina refractory cement - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3.2 (Al2O3 - For Medium purity)	-
4.3.2 (Al2O3 - For Grade I)	-
4.3.2 (Al2O3 - For Grade II)	-
4.3.2 (SiO2 - For Medium purity)	-
4.3.2 (SiO2 - For Grade I)	-
4.3.2 (SiO2 - For Grade II)	-
4.3.2 (Fe2O3 - For Medium purity)	-
4.3.2 (Fe2O3 - For Grade I)	-
4.3.2 (Fe2O3 - For Grade II)	-
4.3.2 (TiO2 - For Medium purity)	-
4.3.2 (TiO2 - For Grade I)	-
4.3.2 (TiO2 - For Grade II)	-
4.3.2 (CaO- For Medium purity)	-
4.3.2 (CaO - For Grade I)	-
4.3.2 (CaO- For Grade II)	-
4.3.2 (MgO- For Medium purity)	-
4.3.2 (MgO - For Grade I)	-
4.3.2 (MgO- For Grade II)	-
4.2 (Fineness)	-
4.5 (Setting time - Initial)	-
4.5 (Setting time - Final)	-
4.4 (Strength - 1 day)	-
4.4 (Strength - 1 day + 1 day at 110°C)	-
4.4 (Strength - 3 days)	-

Partial

IS 11169 : Part 1 (2022)

Specification for steels for cold heading cold extrusion applications: Part 1 wrought carbon and low alloy steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
17 (Shape, Dimensions and tolerances)	-
8.1 (Tensile Test)	-
8.1 (Hardness Test)	-
8.2 (Hardenability (only Applicable to Steel Grades of Annexes B and C))	-
Cl.4.3,7.2 & Table-A.2 (Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Aluminium- Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-

Partial

IS 1417 (2016)

Gold and gold alloys, jewellery/ artefacts - Fineness and marking - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Fineness/ Gold Content in parts per thousand, percent)	-

Partial

IS 10500 (2012)

Drinking water - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4. SL No.i)of Table I (Colour)	-
4.SL No.ii) of Table I (Odour)	-
4.SL No.iii)of Table I (pH)	-
4.SL No.v)of Table I (Turbidity, NTU, Max)	-
4.SL No.vi)of Table I (Total dissolved solids, mg/l, max)	-
table 2 sl.no 1 ( Aluminium (as Al), mg/l, Max)	-
table 2 sl.no 4 (Barium (as Ba), mg/l, Max)	-
table 2 sl.no 5 (Boron (as B), mg/l, Max)	-
table 2 sl.no 6 (Calcium (as Ca), mg/l, Max)	-
table 2 sl.no 7 (Calcium (as Ca), mg/l, Max)	-
table 2 sl.no 9 (Copper (as Cu), mg/l, Max)	-
table 2 sl.no 10 ( Fluoride (as F) mg/l, Max)	-
table 2 sl.no 12 (Iron (as Fe), mg/l, Max)	-
table 2 sl.no 13 (Magnesium (as Mg), mg/l, Max)	-
table 2 sl.no 14 (Manganese (as Mn), mg/l, Max)	-
table 2 sl.no 18 (Selenium (as Se), mg/l, Ma)	-
table 2 sl.no 19 (Silver (as Ag), mg/l, Max)	-
table 2 sl.no 20 (Sulphate (as SO4) mg/l, Max)	-
table 2 sl.no 21 (Sulphide (as H2S), mg/l, Max)	-
table 2 sl.no 22 (Total alkalinity as calcium carbonate, mg/l, Max)	-
table 2 sl.no 23 (Total hardness (as CaCO3 mg/l, Max)	-
table 2 sl.no 24 (Zinc (as Zn), mg/l, Max)	-
TABLE 3 sl no 1 (Cadmium (as Cd), mg/l, Max)	-
TABLE 3 sl no 3 (Lead (as Pb), mg/l, Max)	-
TABLE 3 sl no 4 (Mercury (as Hg), mg/l, Max)	-
TABLE 3 sl no 5 ( Molybdenum (as Mo), mg/l, Max)	-
TABLE 3 sl no 6 (Nickel (as Ni), mg/l, Max)	-
TABLE 3 sl no 7 (Pesticides, µg/l, Max)	-
TABLE 6 sl no 1 (All water intended for drinking: a) E. coli or thermotolerant coliform bacteri)	-
TABLE 6 sl no 2 (Treated water entering the distribution system: a) E. coli or thermotolerant coliform bacteria)	-
TABLE 6 sl no 3 (b) Total coliform bacteria)	-
TABLE 6 sl no 4 (Treated water in the distribution system: a) E. coli or thermotolerant coliform bacteria)	-
TABLE 6 sl no 5 (b) Total coliform bacteria)	-
Table 3, x) (Uranium)	-
Table 1 clause(iv) (Taste)	-

Partial

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1 (Colour)	-
10.1 (Surface Finish)	-
10.7 (Sulphated Ash Content)	-
7.2.1.1 Table3 (Angle of taper (Note-1))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Minimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. Variation)	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-
7.1.1.2 (DIMENSIONS-PIPE-Ovality (Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Minimum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Average Thickness)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-
7.2.1.2(a)-Table 5 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-
7.2.1.2-Table 4 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-
9.1 (PIPE ENDS)	-
10.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.1.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.4 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-
10.6 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-
7.1.3 (mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-
7.1.4 (Length)	-
10.5 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-

Partial

IS 459 (1992)

Corrugated and semi - Corrugated asbestos cement sheets - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12 (Marking - Indication of source of manufacture - Cl. 12)	-
12 (Marking - Year & Date of manufacture - Cl. 12)	-
12 (Marking - Pictorial warning signs as given in IS 12081 (Part 2) : 1987 - Cl. 12)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Depth of Corrugation, D - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Pitch of Corrugation, P - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Overall width, B - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Effective Width, C - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Nominal Thickness, T - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Length of Sheet, A - Cl. 5)	-
6.1 (Load Bearing Capacity Test - Cl. 6.1, IS 5913)	-
7 (General Appearance and Finish - Cl. 7.1)	-
7 (General Appearance and Finish - Cl. 7.2)	-

Partial

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.6 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-
10.4 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-
10.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
9.1 (PIPE ENDS)	-
7.2.1.2-Table 4 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-
7.2.1.2(a)-Table 5 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-
7.2.1 (DIMENSIONS-Socket)	-
7.1.2.1 (DIMENSIONS-PIPE-Average Thickness)	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Minimum))	-
7.1.1.2 (DIMENSIONS-PIPE-Ovality (Maximum))	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. Variation)	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Minimum))	-
7 (DIMENSIONS-PIPE-Nominal Diameter)	-
5 (CLASSIFICATION OF PIPES)	-
Clause 10.7 (Sulphated Ash Content)	-
7.2.1.1 Table3 (Angle of taper (Note-1))	-
10.1 (Surface Finish)	-

Partial

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1.4 (PIPE DESCRIPTION)	-
6.1.3 (PIPE DESCRIPTION)	-
6, 6.1.2 (PIPE DESCRIPTION)	-
6, 6.1.1 (PIPE DESCRIPTION)	-
6, 6.1 (PIPE DESCRIPTION)	-
6.2.1 (6.1.1 Identification Stripes)	-
6.2 (Colour)	-
7.2 (Length)	-
7.4 table -3 & 4 (6.1 Dimensions)	-
7.4.1.2 (Ovality)	-
8.2 (Longitudinal Reversion Test)	-

Partial

IS 10146 (1982)

Specification for polyethylene for its safe use in contact with foodstuffs, pharmaceuticals and drinking water zy

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3 (Pigments and Colourants )	-
3.4 (Overall Migration)	-

Partial

IS 14543 (2016)

Packaged drinking water (Other Than Packaged Natural Mineral Water) - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.3 Table-1vi (pH)	-
5.3 Table-1 v (Total dissolved solids)	-
5.3 Table-1 iv (Turbidity)	-
5.3 Table-1 iii (Taste)	-
5.3 Table-1 ii (Odour)	-
5.3 Table-1 i (Colour)	-
5.3 (Description)	-
5.2.9 (Vibrio parahaemolyticus)	-
5.2.9 (Vibrio cholera)	-
5.2.8 (Shigella)	-
5.2.8 (Salmonella)	-
5.2.7 (Yeast and Mould)	-
5.2.6 (Aerobic Microbial Count at 37°C)	-
5.2.6 (Aerobic Microbial Count at 20-22°C)	-
5.2.5 (Pseudomonas Aeruginosa)	-
5.2.4 (Sulphite Reducing Anaerobes)	-
5.2.3 (Staphylococcus Aureus)	-
5.2.3 (Faecal Streptococci)	-
5.2.2 (Coliform)	-
5.2.1 (Escherichia coli (or thermotolerant bacteria))	-
5.3 Table-3 vii (Nickel (as Ni))	-
5.3 Table-3 vi (Chromium (as Cr))	-
5.3 Table-3 v (Lead (as Pb))	-
5.3 Table-3 iii (Arsenic (as As))	-
5.3 Table-3 ii (Cadmium (as Cd))	-
5.3 Table-3 i (Mercury (as Hg))	-
5.3 Table-2 xxv (Bromates (as BrO3),)	-
5.3 Table-2 xxiv (Borates (as B))	-
5.3 Table-2 xxiii (Antimony (as Sb))	-
5.3 Table-2 xxii (Sulphide (as H2S))	-
5.3 Table-2 xvii (Sodium (as Na))	-
5.3 Table-2 xvi (Magnesium (as Mg))	-
5.3 Table-2 xv (Calcium (as Ca),)	-
5.3 Table-2 xiv (Alkaliniity (as HCO3))	-
5.3 Table-2 xiii (Sulphate (as SO4),)	-
5.3 Table-2 xii (Selenium (as Se),)	-
5.3 Table-2 xi (Chloride (as Cl))	-
5.3 Table-2 x (Aluminium (as Al))	-
5.3 Table-2 ix (Silver (as Ag))	-
5.3 Table-2 viii (Zinc (as Zn))	-
5.3 Table-2vii (Fluoride (as F))	-
5.3 Table-2 vi (Nitrite (as NO2))	-
5.3 Table-2 v (Nitrate (as NO3))	-
5.3 Table-2 iv (Manganese (as Mn))	-
5.3 Table-2 iii (Iron (as Fe),)	-
5.3 Table-2 ii (Copper (as Cu))	-
5.3 Table-2 i (Barium (as Ba))	-
Table 3, x) (Uranium)	-
5.4 i) (Monocrotophos)	-
5.4 ii) (Total pesticied residue)	-
5.4 i) (Dieldrin)	-
5.4 i) (Aldrin)	-
5.4 i) (Malaoxon)	-
5.4 i) (Malathion)	-
5.4 i) (Methyl Paraoxon)	-
5.4 i) (Methyl Parathion)	-
5.4 i) (Atrazine)	-
5.4 i) (Alachlor)	-
5.4 i) (Isoproturon)	-
5.4 i) (Butachlor)	-
5.4 i) (2,4-D)	-
5.4 i) (phorate sulphone)	-
5.4 i) (Phorate sulphoxide)	-
5.4 i) (Phorate)	-
5.4 i) (Chlorpyrifos)	-
5.4 i) (Ethion)	-
5.4 i) (Endosulfan Sulphate)	-
5.4 i) (beta-Endosulfan)	-
5.4 i) (alpha-Endosulfan)	-
5.4 i) (Delta-HCH)	-
5.4 i) (beta-HCH)	-
5.4 i) (alpha-HCH)	-
5.4 i) (Gamma-HCH (Lindane))	-
5.4 i) (p,p DDD)	-
5.4 i) (o,p DDD)	-
5.4 i) (p,p DDE)	-
5.4 i) (o,p DDE)	-
5.4 i) (p,p DDT)	-
5.4 i) (o,p DDT)	-
5.3 Table-3 ix (Polynuclear aromatic hydrocarbons)	-
5.3 Table-3 viii (Polychlorinated biphenyle (PCB))	-
5.4(i) (δ – HCH / USEPA 525.2-1995 (Rev 2) USEPA 508-1989 (Rev 3))	-
5.4(ii) (Total Pesticide Residues / USEPA 525.2-1995 (Rev 2) USEPA 8141A – 1994 (Rev I) USEPA 507-1989 (Rev 2) USEPA 1657A – 2000 USEPA 508-1989 (Rev 3) USEPA 515.1 – 1995 USEPA 532 – 2000 (Rev 1)	-
5.3 Table-2 xxi (Anionic surface active agents (as MBAS))	-
5.3 Table-2 xix (Phenolic compounds (as C6H5OH))	-
5.3 Table-2 xviii (Residual free chlorine)	-

Partial

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 8.3 Table 6 (Hardness Test ( Only for CR0 & CR1))	-
Cl 9.5 (Workmanship)	-
Cl 9.6 (Workmanship)	-
Cl 10 (Workmanship)	-
7.0 (CARBON)	-
7.0 (SULPHUR)	-
7.0 (PHOSPHORUS)	-
7.0 (MANGANESE)	-
Cl. 11 (Width)	-
Cl. 11 (Thickness)	-
Cl 11 (Length, Width & Thickness)	-
Cl. 8.4 (Bend Test)	-
Cl. 8.1 & Table 5A, 5B & 5C (Yield Stress)	-
Cl. 8.1 & Table 5A, 5B & 5C (Elongation at 50 mm gauge length)	-
Cl. 8.1 & Table 5A, 5B & 5C (Elongation at 80 mm gauge length)	-
Cl 8 (UTM)	-

Partial

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (Types)	-
7.2 (DIMENSIONS & TOLERANCES )	-
7.2 (DIMENSIONS & TOLERANCES )	-
7.3 (DIMENSIONS & TOLERANCES )	-
7.4 (DIMENSIONS & TOLERANCES )	-
7.4 (DIMENSIONS & TOLERANCES )	-
8.1 (WORKMANSHIP AND FINISH )	-
8.3 (WORKMANSHIP AND FINISH )	-
10.1.1 (MOISTURE CONTENT)	-
10.1.2, 10.1.2.1 (Table-1) (GLUE ADHESION IN DRY STATE)	-
10.1.2, 10.1.2.2 (GLUE ADHESION IN DRY STATE)	-
10.1.3, 10.1.3.1.1 (Table-1) (RESISTANCE TO WATER TEST)	-
10.1.3, 10.1.3.1.2 (RESISTANCE TO WATER TEST)	-
10.1.4 (RESISTANCE TO WATER TEST)	-
10.1.5 (MYCOLOGICAL TEST )	-
10.1.5, 10.1.5.1 (Table-1) (MYCOLOGICAL TEST )	-
10.1.5.2 (MYCOLOGICAL TEST )	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Parallel to grain))	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Perpendicular to grain))	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Sum of the Tensile Strength in two directions))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-

Partial

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Material)	-
6.0 (Workmanship)	-
4.1 (Sulphur-Percentage by mass)	-
4.1 (Phosphorus-Percentage by mass)	-
8.0 (Straightness)	-
19.1.1, 24.1.1, 28.1.1, 33.1.1 (Dimensions- Outside Dia)	-
19.1.2, 24.1.2, 28.1.2, 33.1.2 (Dimensions- Thickness)	-
11.1 (Surface Protection)	-
11.2 (Surface Protection)	-
19.1.3 (Height of Internal Fin)	-
13.1.3 (Tensile Strength)	-
13.1.1 (Yield Stress)	-
13.1.2 (Elongation)	-
13.3 (Bend Test (Strip))	-
13.4 (Bend Test (Whole Tube))	-
13.2 (Flattening Test)	-

Partial

IS 274 : Part 1 and 2 (1981)

Specification for shovels: Part 1 genral purpose shovels: Part 2 heat - Treated shovels (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Sulphur)	-
4.1 (Phosphorus)	-
5 Table-1,2 (Shape)	-
5 Table-1,2 (Dimensions- A)	-
5 Table-1,2 (Dimensions- B)	-
5 Table-1,2 (Dimensions- C)	-
5 Table-1,2 (Dimensions- D)	-
5 Table-1,2 (Dimensions- E)	-
5 Table-1,2 (Dimensions- G)	-
5 Table-1,2 (Dimensions- H)	-
5 Table-1,2 (Dimensions- K)	-
5 Table-1,2 (Dimensions- L)	-
6.1 (Blade thickness)	-
7.0 (Mass)	-
8.0 (Manufacture)	-
8.0 (Manufacture)	-
8.0 (Manufacture)	-
9.1 (Handles)	-
9.3 (Handles)	-
11.0 (Workmanship & Finish )	-
12.0 (Preservative Treatment )	-
14.2 (Bending Test)	-
14.3 (Flexing Test)	-

Partial

IS 1835 (1976)

Specification for round steel wire for ropes (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 12.2 (UTM)	-
Cl 10 (Diameter)	-
Cl 11.2 (Workmanship)	-
Cl 11.3 (Coating Test)	-
Cl 12.4 (Reverse Bend)	-

Partial

IS 15500 : Part 1 to 8 (2004)

Deepwell handpumps, components and special tools - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2/2.3,(Refer fig 4.1 of Part4) & 9.4 (Part 1) (Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-
2/2.3,(Refer fig 4.5A of Part4) (Dimensions of FIG. 4.5A Flange for Third Plate)	-
2/2.3,(Refer fig 4.8A of Part4) (Dimensions of FIG 4.8A Handle Bar — Standard (For SDWR VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.8C of Part4) (Dimensions of FIG 4.8C Chain Guide)	-
2/2.3,(Refer fig 4.8 D of Part4) (Dimensions of Fig 4.8D Bearing Housing )	-
2/2.3,(Refer fig 4.9 of Part4) (Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-
2/2.3,(Refer fig 4.18A of Part4) (Dimensions of FIG. 4.1 8A Tank Pipe )	-
2/2.3,(Refer fig 4.18C of Part4) (Dimensions of FIG. 4.18C Spout)	-
2/2.3,(Refer fig 4.21 of Part4) (Dimensions of FIG. 4.21 CONNECTING ROD)	-
2/2.3,(Refer fig 4.24of Part4) (Dimensions of FIG. 4.24 HANDLEAXE )	-
2/2.3,(Refer fig 4.26 of Part4) (Dimensions of FIG. 4.26 BEARINGSPACER)	-
2/2.3,(Refer fig 4.27 of Part4) (Dimensions of FIG.4.27 WASHER)	-
2/2.3,(Refer fig 4.12A of Part4) (Dimensions of Fig 4.1 2A Telescopic Stand — Standard (For borewell with 150 NB casing pipe)(For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.12B of Part4) (Dimensions of Fig 4.12B Normal Stand — Standard (For borewell with 1001125 NB casing pipe) (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 5.1 of Part 5) (Dimensions of FIG. 5.1 CYLINDER BODY— STANDARD (For SDWP))	-
2/2.3,(Refer fig 5.4 of Part 5) (Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-
2/2.3,(Refer fig 4.22of Part4) (Dimensions of FIG. 4.22 PLUNGER ROD — STANDARD (For SDWP))	-
2/2.3,(Refer fig 6.1 of Part 6) (Dimensions of FIG. 6.1 A BRASS LINER)	-
2/2.3,(Refer fig 6.9 of Part 6) (Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-
2/2.3,(Refer fig 7.3 of Part 7) (Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-
2/2.3,(Refer fig 6.2 of Part 6) (Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-
2/2.3,(Refer fig 7.6 of Part 7) (Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-
2/2.3,(Refer fig 7.7 of Part 7) (Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-
2/2.3,(Refer fig 6.3 of Part 6) (Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-
2/2.3,(Refer fig 6.4 of Part 6) (Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-
2/2.3,(Refer fig 6.11 of Part 6) (Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-
2/2.3,(Refer fig 6.12 of Part 6) (Dimensions of FIG. 6.12 CHECK VALVE SEAT— STAN~AR~ (For SDWP & EDWP))	-
2/2.3,(Refer fig 6.6 of Part 6) (Dimensions of FIG. 6.6 FOLLOWER — SDWP )	-
2/2.3,(Refer fig 7.1 of Part 7) (Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-
9.4/9.4.1.1 of part 1 (Dimensional and Other Tests/head assembly )	-
9.4/9.4.3of part 1 refer table 3 (Discharge of Pump)	-

Partial

IS 1065 : Part 1 (2019)

Stable bleaching powder - Specification: Part 1 household and industrial use (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2.1 (Description)	-
5.2 (Description)	-
5.3 Table-1 i (Available chlorine)	-
5.3 Table-1 ii (Stability, loss of Chlorine on the basis of initial available chlorine )	-
5.3 Table-1 iiii (Moisture, percent by mass. )	-
5.3 Table-1 iv (Particle size (Passing through 170 mm IS Sieve). Percent by mass)	-
Clause 5.4 (Keeping Quality )	-

Partial

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.6.2 (TRANSPARANCY)	-
4.2 (Design, Shape & Dimension )	-
4.3 (Workmanship, Finish & Appearance)	-
4.4 (b) (Brimful Capacity)	-
Cl. 4.5 (Cl. 4.5 Wall Thickness (Top))	-
Cl. 4.5 (Cl. 4.5 Wall Thickness (Middle))	-
Cl. 4.5 (Cl. 4.5 Wall Thickness (Bottom))	-
Cl. 4.6.3 ( Cl. 4.6.3 Closure Leakage)	-
Cl. 4.6.3 (Cl. 4.6.3 Vibration Leakage)	-
Cl. 4.6.3 (Cl. 4.6.3 Air Pressure Leakage)	-
4.6.4 (DROP TEST)	-
4.6.5 (MIGRATION TEST)	-
Cl. 4.6.5 (Cl. 4.6.5 Migration)	-
4.6.6 (PORTABILITY TEST)	-

Partial

IS 16415 (2015)

Composite cement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Chemical Requirements)	-
6 -Table - 2 i (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
6 -Table - 2 ii (Magnesia - Cl 4.8 of IS 4032:1985)	-
6 -Table - 2 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
6 -Table - 2 iv (Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-
6 -Table - 2 v (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
6 -Table - 2 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
7 and Table 3 i (Fineness IS 4031(Part 2))	-
7 and Table 3 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
7 and Table 3 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 and Table 3 iii a (Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-
7 and Table 3 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 and Table 3 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 and Table 3 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 and Table 3 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
7 and Table 3 v (Drying shrinkage IS 4031(Part 10))	-
Cl. 6.1,Table 2 (Alkali content)	-

Partial

IS 6444 (1979)

Specification for sulphur dusting powders (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-

Partial

IS 3383 (1982)

Specification for wettable sulphur powder

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 Table 1 (Wettability)	-
2.2 Table 1 (Sulphur content, NV upto 9)	-
2.2 Table 1 (Sulphur content, NV above 9 below 50)	-
2.2 Table 1 (Sulphur content, NV above 50)	-
2.2 Table 1 (Material passing through 45 micron IS Sieve, after accelerated storage)	-
2.1 (Description)	-

Partial

IS 8229 (1986)

Specification for oil - Well cement (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 - Table - 1 i (Magnesium Oxide (MgO) - Cl 4.8 of IS 4032:1985)	-
4.1 - Table - 1 ii (Sulphur Trioxide(SO3) - Cl 4.9 of IS 4032:1985)	-
4.1 - Table - 1 iii (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
4.1 - Table - 1 iv (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
4.1 - Table - 1 v (Tricalcium aluminate (3CaO.Al2O3) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 x (Tricalcium Silicate (3CaO.SiO2) - Cl 4 of IS 4032:1985)	-
4.1 - Table - 1 xii (Total alkali content, expressed as Sodium Oxide (Na2O) equivalent - Cl 4.11 of IS 4032:1985)	-
4.1 - Table - 1 xix (Tetracalcium aluminoferrite (4CaO.Al2O3.Fe2O3) plus twice the tricalcium aluminate (3CaO.Al2O3) - Cl 4 of IS 4032:1985)	-
5.1 and Table 2 ii (Fineness IS : 4031:1988)	-
5.1 and Table 2 iii (Soundness, Autoclave expansion IS 4031:1988)	-

Partial

IS 8043 (1991)

Specification for hydrophobic Portland cement

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (ref. 6 - Table - 1 i of IS 269:2015) (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 ii of IS 269:2015) (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 iii of IS 269:2015) (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 iv of IS 269:2015) (Magnesia - Cl 4.8 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 v of IS 269:2015) (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 vi of IS 269:2015) (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 vii of IS 269:2015) (Chloride content - Cl 4.13 of IS 4032:1985)	-
5.1 (ref. 6 - Table - 1 viii of IS 269:2015) ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
6.1 (Fineness 4031 Part 2)	-
6.2 (Expansion by Le Chatelier- IS 269 & 4031 Part 3)	-
6.2 (Expansion after aeration - IS 269 & 4031 Part 3)	-
6.2 (Expansion by Autoclave- IS 269 & 4031 Part 3)	-
6.2 (Expansion after aeration- IS 269 & 4031 Part 3)	-
6.2 (Setting Time Initial- IS 269 & 4031 Part 5)	-
6.2 (Setting Time Final- IS 269 & 4031 Part 5)	-

Partial

IS 12600 (1989)

Portland cement, low heat - specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 - Table - 1 i (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 ii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 - Table - 1 iii (Magnesia - Cl 4.8 of IS 4032:1985)	-
5.1 - Table - 1 iv (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5.1 - Table - 1 v ( Total loss on ignition - Cl 4.2 of IS 4032:1985)	-
5.2 (Lime after deduction of that necessary to combine with Sulphuric anhydride - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 note 2 (Alkali content as Na2O - Cl 4.11 of IS 4032:1985)	-
6.1 (Fineness 4031 Part 2)	-
6.2.1 (Expansion by Le Chatelier- 4031 Part 3)	-
6.2.1.1 (Expansion after aeration - 4031 Part 3)	-
6.2.1 (Expansion by Autoclave- 4031 Part 3)	-
6.2.1.1 (Expansion after aeration- 4031 Part 3)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.4 a) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6.4 c) (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-

Partial

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Patna Branch Laboratory (PBL)

Bureau of Indian Standards, Patliputra Industrial Estate, Patna - 800013, Patna, Patna, Bihar, 800013

- pbol@bis.gov.in

Scope List