BIS - LIMS (Laboratory Information Management System)

BIS, Patna Branch Laboratory (PBL)

Bureau of Indian Standards, Patliputra Industrial Estate, Patna, Patna, Bihar, 800013

- pbol@bis.gov.in

Scope List

Reset

82 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1835 (1976)

Specification for round steel wire for ropes (Third Revision)

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 12.2 (UTM)	-
Cl 10 (Diameter)	-
Cl 12.4 (Reverse Bend)	-
Cl 12.3 (Torsion)	-
Cl 12.5 (Wrap)	-
Cl. 5.1, T-1 (C)	-
Cl. 5.1, T-1 (Mn)	-
Cl. 5.1, T-1 (Si)	-
Cl. 5.1, T-1 ( Grade 1) (S)	-
Cl. 5.1, T-1 ( Grade 1) (P)	-
Cl. 9.1, T-3 (Uniformity)	-
Cl. 9.1, T-3 (Mass of Zinc Coating)	-

-
All test facilities are available as per the IS except tests for Copper, Nickel and Chromium (Clause 5.1)

IS 1065 : Part 1 (2019)

Stable bleaching powder - Specification: Part 1 household and industrial use (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2.1 (Description)	-
5.2 (Description)	-
5.3 Table-1 i (Available chlorine)	-
5.3 Table-1 ii (Stability, loss of Chlorine on the basis of initial available chlorine )	-
5.3 Table-1 iiii (Moisture, percent by mass. )	-
5.3 Table-1 iv (Particle size (Passing through 170 mm IS Sieve). Percent by mass)	-
Clause 5.4 (Keeping Quality )	-

-
All test facilities are available as per the IS

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

5850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.6.2 (TRANSPARANCY)	-
4.2 (Design, Shape & Dimension )	-
4.3 (Workmanship, Finish & Appearance)	-
4.4 (b) (Brimful Capacity)	-
Cl. 4.5 (Cl. 4.5 Wall Thickness (Top))	-
Cl. 4.5 (Cl. 4.5 Wall Thickness (Middle))	-
Cl. 4.5 (Cl. 4.5 Wall Thickness (Bottom))	-
Cl. 4.6.3 ( Cl. 4.6.3 Closure Leakage)	-
Cl. 4.6.3 (Cl. 4.6.3 Vibration Leakage)	-
Cl. 4.6.3 (Cl. 4.6.3 Air Pressure Leakage)	-
4.6.4 (DROP TEST)	-
4.6.6 (PORTABILITY TEST)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ix) (Phthalic acid, bis(2-ethylhexyl) ester (DEHP))	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(i) (Specific migration for Cap,Barium)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(ii) (Specific migration for Cap,Cobalt)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(iii) (Specific migration for Cap,Copper)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(iv) (Specific migration for Cap,Iron)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(v) (Specific migration for Cap,Lithium)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(vi) (Specific migration for Cap,Manganese)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(vii) (Specific migration for Cap,Zinc)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(viii) (Specific migration for Cap,Antimony)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(ix) ("Specific migration for Cap,Phthalic acid, bis(2-ethylhexyl) ester (DEHP)")	-
Cl. 4.6.5 (Overall migration for Cap)	-
Cl. 4.6.5.1 (Colour migration for Cap)	-
4.6.5 (MIGRATION TEST)	-
Cl. 4.6.5 (Cl. 4.6.5 Migration)	-

-
All test facilities are available as per the IS. Sample Size: 200 ml and 250 ml (50 empty bottle + 80 caps), 500 ml and 1 Litre (30 empty bottle + 80 caps), 2 Litre (15 empty bottle + 80 caps), 5 Litre ( 10 empty bottle + 40 caps), 20 Litre (06 empty jar + 40 caps)

IS 16415 (2015)

Composite cement - Specification

Rs.9150/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Chemical Requirements)	-
6 -Table - 2 i (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
6 -Table - 2 ii (Magnesia - Cl 4.8 of IS 4032:1985)	-
6 -Table - 2 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
6 -Table - 2 iv (Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-
6 -Table - 2 v (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
6 -Table - 2 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
7 and Table 3 i (Fineness IS 4031(Part 2))	-
7 and Table 3 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
7 and Table 3 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 and Table 3 iii a (Setting Time ( by Vicat Apparatus), Initial IS 4031(Part 5))	-
7 and Table 3 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 and Table 3 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 and Table 3 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 and Table 3 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
7 and Table 3 v (Drying shrinkage IS 4031(Part 10))	-
Cl. 6.1,Table 2 (Alkali content)	-

-
All test facilities are available as per the IS except Transverse Strength Test (serial no. i to vi of Table 3 and Clause 7) which is an optional test

IS 6444 (1979)

Specification for sulphur dusting powders (First Revision)

Rs.2100.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-

-
All test facilities are available as per the IS

IS 3383 (1982)

Specification for wettable sulphur powder

Rs 4200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 Table 1 (Wettability)	-
2.2 Table 1 (Sulphur content, NV upto 9)	-
2.2 Table 1 (Sulphur content, NV above 9 below 50)	-
2.2 Table 1 (Sulphur content, NV above 50)	-
2.2 Table 1 (Material passing through 45 micron IS Sieve, after accelerated storage)	-
2.1 (Description)	-

-
All test facilities are available as per the IS

IS 8041 (1990)

Rapid hardening portland cement - Specific4tion (Second Revision)

Please see remarks View breakup
Testing charges for the product are: Including Transverse Strength (optional test) test 9,100.00 Excluding Transverse Strength (optional test) test 7,900.00 -Testing charges for only chemical test report: 4,300.00 -Testing charges for only physical test report including optional tests: 4,800.00 -Testing charges for only physical test report excluding optional tests: 3,600.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 ii (Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-
5.1 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5.1 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5.1 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5.1 - Table - 1 vi (Total loss on ignition - Cl 4.2 of IS 4032:1985)	-
6.1 (Fineness 4031 Part 2)	-
6.2.1 (Expansion by Le Chatelier- 4031 Part 3)	-
6.2.1.1 (Expansion after aeration - 4031 Part 3)	-
6.2.1 (Expansion by Autoclave- 4031 Part 3)	-
6.2.1.1 (Expansion after aeration- 4031 Part 3)	-
6.3 a) (Setting Time Initial- 4031 Part 5)	-
6.3 b) (Setting Time Final- 4031 Part 5)	-
6.4 a) (Compressive Strength At 24 hrs ± 30 minutes - IS 4031 Part 6)	-
6.4 b) (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-

-
All test facilities are available as per the IS

IS 15911 (2010)

Structural steel (Ordinary Quality) - Specification

Rs 6750/- For elements other than Table-1: Rs 1004/- pe View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1, 5.1, 8.1 & 8.2 (Carbon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Sulphur: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Silicon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Nitrogen: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
7 (Freedom from defects)	-
5 and 10.3.1 (Tensile strength. IS 1608)	-
5 and 10.3.1 (Yield Stress. IS 1608)	-
5 and 10.3.1 (Percentage Elongation. . IS 1608)	-
11.3 ( Bend Test. IS 1599)	-
5 and 10.3.1 (Internal Bend Diameter)	-
Cl 12 of IS 15911 and Table 5.1 of IS 808 (Mass. IS 808)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (D)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (B)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (t)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (T)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (Flange Slop, Max α , )	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (R1)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (R2)	-

-
All test facilities are available as per the IS except tests for Chromium, Molybdenum, Vanadium, Nickel, Copper, Niobium, Boron, Titanium, Aluminium and Tungsten (Clause 8.2)

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

Rs.1800/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1, Table-1, Fig-1 (Nominal size)	-
3.2.1, Table-1, Fig-1 (B)	-
3.2.1, Table-1, Fig-1 (Minimum wall thickness for working pressure)	-
3.2.1, Table-1, Fig-1 (Plumbing)	-
Clause 3.2.2, and Fig. 2 (Nominal size)	-
Clause 3.2.2, and Fig. 2. (B)	-
Clause 3.2.2, and Fig. 2. (Minimum wall thickness for working pressure)	-
3.2.2, and Fig. 2 (Dimensions of Socket for Elastomeric Sealing Ring Joint)	-

-
All test facilities are available as per the IS except- i. Short Term Hydrostatic Test (Clause 6.2) ii. Effect on Water (Clause 6.3)

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

Rs 5100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
7.1 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
8.1.1 Table 1 (Tensile Strength- IS 1608(1))	-
8.1.1 Table 1 (Yield Strength- IS 1608)	-
8.1.1 Table 1 (Elongation Percent- IS 1608)	-
9.1 Table 2 (Outside Diameter)	-
9.1 Table 2 (Thickness)	-
9.1 Table 2 (Mass)	-
10 (Hardness)	-
13.1.1 (Ovality)	-
13.1.2 (Eccentricity)	-
15.1 (Straightness)	-
16.1 (Length)	-
17.1 (Surface Protection)	-

-
All test facilities are available as per the IS

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 15 (Length, Width & Thickness)	-
Cl 9 (Press)	-
Cl 13 (Workmanship)	-
7.1 (Carbon %)	-
7.1 (Manganese %)	-
7.1 (Phosphorus %)	-
7.1 (Sulphur %)	-
7.1 (Silicon %)	-
7.1 ( Nitrogen%)	-
7.1 (CE)	-

-
All test facilities are available as per the IS except- i. Hole Expansion Ratio Test (Clause 8.3 and Table 7) ii. Cr, Mo, Ni, Al, Cu and microalloying elements (Clause 7.2)

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.7.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Depth))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Width))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections(Thickness))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Weigth))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Area of Section))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Moment of Inertia))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Radius of Gyration))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections(Elastic Modulus))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Plastic Modulus))	-
Cl. 10.1, 14.1, 18.1 (Straightness)	-
Cl. 10.2, Fig 1 (Outside dimension (B))	-
Cl. 10.2, Fig 1 (Outside dimension (H))	-
Cl. 10.2, Fig 1 (Outside dimension (T))	-
Cl. 10.4, Fig 2 (Concavity, X1)	-
Cl. 10.4, Fig 2 (Convexity, X2)	-
Cl. 10.5, Fig 3 (Squareness of side)	-
Cl. 10.6, Fig 4 (External Corner Radius)	-
Cl. 10.7, Fig 5 (Total twist, V)	-
Cl. 15.2, Table 3 (Tensile Strength- IS 1608)	-
Cl. 15.2, Table 3 (Yield Strength- IS 1608)	-
Cl. 15.2, Table 3 (Elongation- IS 1608)	-
Cl. 14.1 (Exact Length)	-
Cl. 14.1 (Random Length)	-
Cl. 14.1 (Weight on individual length)	-
Cl.7.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 18, Note 2 (Internal Fin Height (Only for Cold Formed))	-

-
All test facilities are available as per the IS except chemical tests for Aluminium, Copper, microalloying elements (Nb, V, Ti ) and alloying elements (Cr, Ni, Mo, B) (Clause 7.1)

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.1 (Mechanical Properties (as per table 5 of IS 1608))	-
8.3 (Mechanical Properties (as per IS 1755))	-
8.2 (Mechanical Properties (as per IS 1717))	-
9.1 (Galvanizing Requirements )	-
9.2 (Galvanizing Requirements )	-
9.3 (Galvanizing Requirements )	-
6.2 (Phosphorus %)	-
6.2 (Sulphur %)	-
Clause 6.1, Table-1 (Sulphur)	-
Clause 6.1, Table-1 (Phosphorus)	-
11 (Freedom from defects)	-

-
All test facilities are available as per the IS except Adhesion Test (Clause 9.3)

IS 3589 (2001)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

Please see remarks. View breakup
Rs. 11800/- (for SAW Pipe ) Rs. 10380/- for (ERW Fe410 , Fe450 &Fe330)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1 Table 2 Table 3 (Carbon Content IS 228)	-
8.1 Table 2 Table 3 (Manganese Content IS 228)	-
8.1 Table 2 Table 3 (Phosphorus Content IS 228)	-
8.1 Table 2 Table 3 (Sulphur Content IS 228)	-
11.1, Table 5. (Outside Diameter (OD))	-
11.1, Table 5. (Thickness)	-
11.1, Table 5. (Mass)	-
12.3.3 (Ovality)	-
12.5 (Strightness)	-
14.1 (Visual inspection, Appearance and Workmanship)	-
14.2 (Visual inspection, Appearance and Workmanship)	-
14.3 (Visual inspection, Appearance and Workmanship)	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Depth(below 610 mm OD))	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Depth(Above 610 mm OD))	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Length)	-
14.4 (Visual inspection, Appearance and Workmanship-Dent Length)	-
9.1 (Tensile test-Yield Strength)	-
9.1 (Tensile test-Strength)	-
9.1 (Tensile test- Elongation)	-
9.3 (Guided Bend Test (for SAW Pipes))	-
9.2.3 (Flattening Test for seamless pipes)	-
9.2.1 (Flattening test for ERW pipes )	-

-
All test facilities are available as per the IS except- i. Hydraulic Pressure Test (Clause 10) [This test is to be carried out at the manufacturers' end only.] ii. Tests for micro alloying elements and Aluminium (Clause 8.2) iii. Ovality Test Facility is not available for size 273 mm and above (Clause 12.3.3)

IS 299 (2012)

Alumino - Ferric - Specification (Fifth Revision)

Please see remarks View breakup
testing charges are Rs.3250.00 (for Grade 1, 2 & 3) and Rs.8250.00 (for Grade 4 & 5).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1 (i) Table 1 ( Insouble matter, Grade 1, A-3)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 1, A-4)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 1, A-5)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 1, A-6)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 1, A-7)	-
1 (i) Table 1 ( Insouble matter, Grade 2, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 3, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 4, A-3)	-
1 (i) Table 1 ( Insouble matter, Grade 5, A-3)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 2, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 3, A-4)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 4, A-4)	-
1 (ii) Table 1 (Soluble iron compound as Fe2+ and Fe3+), Grade 5, A-4)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 2, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 3, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 4, A-5)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 5, A-5)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 2, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 3, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 4, A-6)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 5, A-6)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 2, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 3, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 4, A-7)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 5, A-7)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 1, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 2, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 3, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 4, A-9)	-
1 (vii) Table 1 (Arsenic (as As2O3), Grade 5, A-9)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 1, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 2, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 3, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 4, A-10)	-
1 (viii) Table 1 (Mercury (as Hg), Grade 5, A-10)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 1, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 2, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 3, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 4, A-11)	-
1 (ix) Table 1 (Manganese (as Mn), Grade 5, A-11)	-
1 (x) Table 1 (Chromium (as Cr), Grade 1, A-12)	-
1 (x) Table 1 (Chromium (as Cr), Grade 2, A-12)	-
1 (x) Table 1 (Chromium (as Cr), Grade 3, A-12)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 4, A-13)	-
1 (x) Table 1 (Chromium (as Cr), Grade 5, A-12)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 1, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 2, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 3, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 4, A-13)	-
1 (xi) Table 1 (Cadmium (as Cd), Grade 5, A-13)	-
1 (xii) Table 1 (Selenium (as Se), Grade 1, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 2, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 3, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 4, A-14)	-
1 (xii) Table 1 (Selenium (as Se), Grade 5, A-14)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 1, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 2, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 3, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 4, A-15)	-
1 (xiii) (a) Table 1 (Organic impurities:Phenolic compounds (as C6H5OH), Garde 5, A-15)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 1, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 2, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 3, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 4, A-16)	-
1 (xiii) (b) Table 1 (Anionic detergents (as MASS), Garde 5, A-16)	-
Clause 4.1 (Description)	-

-
-

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

Testing charges are Rs.9050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 8 & 9 (Diameter)	-
6 (Carbon %)	-
6 (Manganese %)	-
6 (Phosphorus %)	-
6 (Sulphur %)	-
6 (Silicon %)	-
Cl. 9.2 (Maximum Difference between 2 readings taken at any 2 diameters across cross section)	-
Cl. 8,9 (Width across flat)	-
Cl. 8,9 (Length)	-

-
All test facilities are available as per the IS except tests for Copper, Vanadium, Nickel, Titanium, Chromium and Almunium (Clause 6)

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

Rs.3750.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 & Table 1 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
Cl 9 (Tensile Test On UTM)	-
Cl 11 (Workmanship)	-
Cl 13 (Workmanship)	-
6 AND AS PER IS 7887 (PHOSPHORUS)	-
6 AND AS PER IS 7887 (SULPHUR)	-
6 AND AS PER IS 7887 (MANGANESE)	-
6 AND AS PER IS 7887 (SILICON)	-
6 AND AS PER IS 7887 (CARBON)	-
9.2 (Wrapping Test)	-
9.3 (Bend test)	-
10 (Finish)	-
11 (Coating test)	-
13 (Freedom from defects)	-
11 (Coating test)	-

-
All test facilities are available as per the IS except tests for Aluminium and Copper (Clause 6)

IS 253 (2014)

Specification for common salt (Fourth Revision)

6690 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause -3 for common salt 3.1 ( 3.1.1 ) ( The material shall be crystalline solid, white or pale pink or light grey in colour.)	-
Clause -3 for common salt 3.1 ( 3.1.2 ) Annex-2 (Moisture The material shall contain not more than 6.0 percent by mass of moisture, on as received basis, when tested according to the method given in A-2)	-
Clause-3.2 for dairy salt (3.2.1) (The material shall be crystalline white solid and free from any visible impurities.)	-
Clause-3.1 for dairy salt (3.2.2) (3.2.2 Particle Size 99 percent by mass of the material shall pass completely through 850-micron IS Sieve [see IS 460 (Part I)].)	-
Clause-3.2 for dairy salt (3.2.3) Annex -2 (3.2.3 Moisture The material shall contain not more than 0.5 percent by mass of moisture, on as received basis, when tested according to the methods given in A-2.)	-
Table 1 (i) Annex -4 (Water insoluble matter, common)	-
Table 1 (i) Annex -4 (Water insoluble matter, Dairy)	-
Table 1 (ii) Annex-5 (Chloride content (as NaCl)common)	-
Table 1 (ii) Annex-5 (Chloride content (as NaCl), Dairy)	-
Table 1 (iii) Annex-6 ( Matter soluble in water, other than sodium chloride, common)	-
Table 1 (iii) Annex-6 ( Matter soluble in water, other than sodium chloride, Dairy)	-
Table 1 (iv) (Calcium (as Ca), water soluble, percent by mass, common)	-
Table 1 (iv) Annex-7 (Calcium (as Ca), water soluble, percent by mass, Dairy)	-
Table 1 (v) (Magnesium (as Mg), water soluble, percent by mass, common )	-
Table 1 (v) Annex-7 (Magnesium (as Mg), water soluble, percent by mass, Dairy )	-
Table 1 (vi) (Sulphate as SO2 percent by mass, common)	-
Table 1 (vi) Annex-8 (sulphate as SO2 percent by mass, Dairy)	-
Table 1 (vii) Annex-9 (Alkalinity (as Na2CO3), common)	-
Table 1 (vii) Annex-11 (Alkalinity (as Na2CO3), Dairy)	-
Table 1 (ix) (Iron (as Fe), common)	-
Table 1 (ix) (Iron (as Fe), Dairy)	-
Table 1 (xi) Annex-12 (Copper (as Cu), common)	-
Table 1 (xi) Annex-12 (Copper (as Cu), Dairy )	-
Table 1 (x) Annex-11 (x) Arsenic (as As), common)	-
Table 1 (x) Annex-11 (x) Arsenic (as As),Dairy)	-

-
All test facilities are available as per the IS except tests for Lead (Clause 3.1.4)

IS 2124 (2000)

Sodium bicarbonate - Specification (Second Revision)

Rs 4660/- for Pure Grade View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Grade)	-
4.1 (Description)	-
4.2 (Table 1 S.no.(i)) (Total Alkalinity (as NaHCO3))	-
4.2 (Table 1 S.no.(i)) (pH )	-
4.2 (Table 1 S.no.(ii)) (Chlorides (as Cl))	-
4.2 (Table 1 S.no.(iii)) (Insoluble matter)	-
4.2 (Table 1 S.no.(iv)) (Sulphates (as SO4))	-

-
All test facilities are available as per the IS

IS 1507 (1977)

Specification for copper oxychloride water dispersible powder concentrates

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.2.1 (Description)	-
Cl. 2.3, Table-1 (pH of one percent aqueous dispersion)	-

-
All test facilities are available as per the IS

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

Rs.8420/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-

-
All test facilities are available as per the IS except Transverse Strength Test (Clause 7 and Table-2) which is an optional test

IS 1148 (2009)

Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

8660 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
7 (FREEDOM FROM DEFECTS)	-
8 ( LENGTHS)	-
9 (DIMENSIONAL TOLERANCES)	-
11 (Tensile Test-1608:Part 1)	-
11 (Yield Strength, Mpa)	-
11 (Tensile Strength, Mpa)	-
11 (Elongation, %)	-
12 (Bend Test-1599)	-

-
All test facilities are available as per the IS except- i. Tests for microalloying elements (Nb, V, Ti and B) and Aluminium (Clause 6.2) ii. Shear Test (Clause 13) iii. Hot Compression Test (Clause 14)

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8, Table 5 & 6 (Tensile Strength)	-
Cl 12 (Workmanship)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
6.1 ( Nitrogen%)	-
8, Table 5 & 6 (Yield Strength)	-
8, Table 5 & 6 (Elongation)	-
Clause 10 (Cuppping Test)	-
Clause 12 (Freedom from defect)	-
Clause 13 (Length)	-
14 (Calculation of weight)	-
Cl.13 (Out of square)	-
Cl.13 (Flatness)	-
Cl.13 (Camber)	-
Cl.13 (Width)	-
Cl.13 (Thickness)	-

-
All test facilities are available as per the IS except- i. Cupping Test (Clause 10) ii. Chemical tests for Boron, Titanium, Niobium, Vanadium, Aluminium and Copper (Clause 7.2)

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

Please see remarks View breakup
i) For grade 1,2&3 = 3716 /-, Rounded off to Rs.3750/- ii) For grade 4,5 & 6 including Micro alloying elements = 6728/-, Rounded off to Rs.6750/- Remarks: Testing chargesfor each of the elements other than Table-1 (Silicon, Aluminum, Nitrogen etc.) will be Rs.1004/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 & Table 3 (UTM)	-
Cl 9 (Press)	-
Cl 11 (Workmanship)	-
Cl 12 & 13 (Length, Width & Thickness)	-
7.1 (Carbon %)	-
7.1 (Manganese %)	-
7.1 (Phosphorus %)	-
7.1 (Sulphur %)	-
Cl. 8, Table 3 (Yield Stress)	-
Cl. 14 (Weight)	-
Cl. 12, 13 (Camber)	-
Cl. 12, 13 (Thickness)	-
Cl. 8, Table 3 (Elongation)	-
7.1 (Silicon %)	-
7.1 (CE)	-
7.1 ( Nitrogen%)	-

-
All test facilities are available as per the IS except chemical tests for Chromium, Molybdenum,Vanadium, Nickel, Copper, Niobium, Boron, Titanium, Aluminium and Tungsten (Clause 7.2)

IS 1038 (1983)

Specification For Steel Doors, Windows And Ventilators

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1. (Size-Height)	-
4.1 (Size-Width)	-
4.3 (Designation)	-
6.1 (Frames)	-
6.1.1.1 (Visual Inspection Test)	-
6.2 (Side Hung Shutter)	-
6.2 (Side Hung Shutter)	-
6.2 (Side Hung Shutter- Thickness of hinge)	-
6.2 (Side Hung Shutter- Pin diameter)	-
6.2 (Side Hung Shutter-Width of hinge)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate- Thicknesss of handle)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate-Height of handle plate)	-
6.2.3 (Peg Stay - Thickness)	-
6.2.3 (Peg Stay - Dimensions-A)	-
6.2.3 (Peg Stay - Dimensions-B)	-
6.2.3 (Peg Stay - Dimensions-C)	-
6.2.3 (Peg Stay - Dimensions-D)	-
6.2.3 (Peg Stay - Dimensions-E)	-
6.2.3 (Peg Stay - Dimensions-F)	-
6.2.3 (Peg Stay - Dimensions-G)	-
6.2.3 (Peg Stay - Dimensions-H)	-
6.2.3 (Peg Stay - Dimensions-J)	-
6.2.3 (Peg Stay - Dimensions-K)	-
6.2.3 (Peg Stay - Dimensions-L)	-
6.2.3 (Peg Stay - Dimensions-M)	-
6.3 (Top Hung Ventilator)	-
6.3 (Top Hung Ventilator-Thickness of hinge)	-
6.3 (Top Hung Ventilator-Pin diameter)	-
6.3 (Top Hung Ventilator-Width of hinge)	-
7.1 (Position of Holes)	-
7.2 Table 2 (Position of Fixing Screws)	-
7.2 Table 2 (Lugs-A)	-
7.2 Table 2 (Lugs-B)	-
7.2 Table 2 (Lugs-C)	-
7.2 Table 2 (Lugs-D)	-
7.2 Table 2 (Lugs-E)	-
7.2 Table 2 (Lugs-F)	-
7.2 Table 2 (Lugs-G)	-
8 (Finish)	-
9 (Glazing)	-
9 (Glazing- No of glazing clip against each plate)	-

-
All test facilities are available as per the IS

IS 6003 (2010)

Indented Wire For--Prestressed Concrete ”

Rs.4110/- excl. relaxation test View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 6.1.2 (Weight)	-
Cl 7.1 (Tensile Test On UTM)	-
Cl 7.2 (Tensile Test On UTM)	-
Cl 7.3 (Reverse Bend Test)	-
Cl 7.4 (Tensile Test On UTM)	-
Cl 7.5 (Load )	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-

-
All test facilities are available as per the IS except- i. Ductility Test (Clause 7.3) ii. Reverse Bend Test (Clause 8.5)

IS 7224 (2006)

Iodized salt, vacuum evaporated iodized salt and refined iodized salt - Specification (Second Revision)

Rs7440/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2 (Particle Size)	-
Clause 4.3 Table 1 (Moisture content)	-
Clause 4.3 Table 1 (water insoluble matter)	-
Clause 4.3 Table 1 (Chloride Content(as Nacl))	-
Clause 4.3 Table 1 (Matter soluble in water other than sodium chloride)	-
Clause 4.3 Table 1 (Calcium (as Ca))	-
Clause 4.3 Table 1 (Magnesium (as mg))	-
Clause 4.3 Table 1 (Sulphate (as SO4 ),)	-
Clause 4.3 Table 1 (Iodine content, a) Manufacturers Level )	-
Clause 4.3 Table 1 (Alkalinity (as Na2CO3),)	-
Clause 4.3 Table 1 (Iron(as Fe))	-
Clause no4.1 (Description)	-
Clause 4.3 Table 1 (Arsenic(as As))	-

-
All test facilities are available as per the IS except chemical tests for determining Lead Content (Clause 4.3 and Table 1)

IS 277 (2018)

Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8.2 (Press)	-
Cl 13 (Weight)	-
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Pitch of Corrugation))	-
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Depth of Corrugation))	-
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Number of Corrugation))	-
Cl. 14 & Cl. 15 (Cl. 14 & Cl 15 (Difference between Diagonal))	-
Cl. 14 & Cl. 15 (Cl. 14 & Cl. 15 (Thickness))	-
Cl. 14 (Cl. 14 & Cl 15 (Width))	-
Cl. 14 (Cl. 14 & Cl 15 (Length))	-
Cl.12 (Freedom from defects)	-
Cl. 8.1 (Cl. 8.1 (Percentage Elongation ))	-
Cl. 8.1 (Cl. 8.1 (Yield Stress))	-
Cl. 8.1 (Cl. 8.1 (Tensile Strength))	-
5.1 (carbon)	-
5.1 (manganese)	-
5.1 (phosphorus)	-
5.1 (sulphur)	-
7.4 (Mass of Coating: Single Spot Test)	-
7.4 (Mass of Coating: Triple Spot Test)	-

-
All test facilities are available as per the IS except tests for - i. Microalloying elements and Aluminium (Clause 5.1) ii. Surface Finish (Clause 9)

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

Rs. 4500/- View breakup
Excluding Macro examination and Sulphur print

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1, Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 6.1, Table 1 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
All test facilities are available as per the IS except tests for Al, microalloying elements, Cr, Ni and Mo (Clause 6.1)

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
6.1 ( Nitrogen%)	-

-
All test facilities are available as per the IS except tests for microalloying elements (Nb, V, Ti and B) and Aluminium (Clause 6.2)

Bureau of Indian Standards

The National Standards Body of India

BIS, Patna Branch Laboratory (PBL)

Bureau of Indian Standards, Patliputra Industrial Estate, Patna, Patna, Bihar, 800013

- pbol@bis.gov.in

Scope List