BIS - LIMS (Laboratory Information Management System)

Shri Krishna Test House

Plot No 88, Sector -E, Bawana-II, DSIIDC Industrial complex New Delhi, Delhi, Shahdara, Delhi, 110040

9891112786 skth1234@gmail.com

Scope List

Reset

65 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 21 (2025)

Wrought Aluminium and Aluminium Alloys for Manufacture of Utensils - Specification (Fifth Revision)

ALL

70000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirements)	-	500	-
Cl-5.1(Material)	-	6000	-
Cl-5.2(Chemical composition and mechanical properties of grades in Cl 5.1)	-	6500	-
Cl-5.3.1 a("Wrought Aluminium (with Minimum 99 Percent Al Content)- Iron+ Silicon")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Chromium")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Magnesium")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Manganese")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Nickel")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Zinc")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Titanium")	-	1000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Tin")	-	1000	-
Cl-5.3.1 c("Wrought Aluminium (with Minimum 99 Percent Al Content)- Copper")	-	1000	-
Cl-5.3.1 Note 1("Wrought Aluminium (with Minimum 99 Percent Al Content)- Aluminium")	-	1000	-
Cl-5.3.1 d("Wrought Aluminium (with Minimum 99 Percent Al Content)- Others")	-	1000	-
Cl-5.3.2, Table-1 (i)(Wrought Aluminium Alloys-Silicon)	-	1000	-
Cl-5.3.2, Table-1 (ii)(Wrought Aluminium Alloys-Iron)	-	800	-
Cl-5.3.2, Table-1 (iii)(Wrought Aluminium Alloys-Copper)	-	800	-
Cl-5.3.2, Table-1 (iv)(Wrought Aluminium Alloys-Manganese)	-	800	-
Cl-5.3.2, Table-1 (v)(Wrought Aluminium Alloys-Magnesium)	-	800	-
Cl-5.3.2, Table-1 (vi)(Wrought Aluminium Alloys-Chromium)	-	800	-
Cl-5.3.2, Table-1 (vii)(Wrought Aluminium Alloys-Nickel)	-	800	-
Cl-5.3.2, Table-1 (viii)(Wrought Aluminium Alloys-Zinc)	-	800	-
Cl-5.3.2, Table-1 (ix)(Wrought Aluminium Alloys -Zirconium)	-	1500	-
Cl-5.3.2, Table-1 (x)(Wrought Aluminium Alloys - Titanium)	-	600	-
Cl-5.3.2, Table-1 (Note 3)(Wrought Aluminium Alloys- Aluminium)	-	1000	-
Cl-5.3.2, Table-1 (xi)(Wrought Aluminium Alloys- Others)	-	1000	-
Cl 5.4(Lead)	-	800	-
Cl 5.4(Cadmium)	-	800	-
Cl 5.4(Arsenic)	-	800	-
Cl-7(Dimension)	-	500	-
Cl-8(EARING TEST (OPTIONAL TEST))	-	2000	-
Cl-5.2, (Cl-8,Table 2 of IS 737)(0.2% Proof Stress)	-	2500	-
Cl-5.2, (Cl-8,Table 2 of IS 737)(Tensile Strength)	-	2500	-
Cl-5.2, (Cl-8,Table 2 of IS 737)(Elongation)	-	1500	-
Cl-5.2, (Cl-8,Table 2 of IS 737)(Bend Test)	-	3000	-

05 Oct, 2028

-
Included w.e.f 09.03.2026

IS 733 (2025)

Wrought Aluminium and Aluminium Alloy Bars, Rods, Sections, Extruded Tube, Hollow Sections and Profiles for General Engineering Purposes ? Specification (Fourth Revision)

All

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 Table 1 - Table 8(Sodium)	-	500	-
Cl. 6 Table 1 - Table 8(Strontium)	-	500	-
Cl. 6 Table 1 - Table 8(Antimony)	-	500	-
Cl. 6 Table 1 - Table 8(Phosphorus)	-	500	-
Cl. 6 Table 1 - Table 8(Zirconium +Titanium)	-	500	-
Cl-4(General requirements)	-	500	-
Cl-6.1, Table-1 to 8(Fe)	-	500	-
Cl-6.1, Table-1 to 8(Cu)	-	500	-
Cl-6.1, Table-1 to 8(Mn)	-	500	-
Cl-6.1, Table-1 to 8(Mg)	-	500	-
Cl-6.1, Table-1 to 8(Cr)	-	500	-
Cl-6.1, Table-1 to 8(Zn)	-	500	-
Cl-6.1, Table-1 to 8(Ti)	-	500	-
Cl-6.1, Table-1 to 8(V)	-	500	-
Cl-6.1, Table-1 to 8(Aluminium)	-	500	-
Cl-6.2(chemical analysis)	-	4000	-
Cl-7.1, 7.2 & 7.3, Table-9(Dimensions)	-	500	-
Cl-7.1, 7.2 & 7.3, Table-9(Rm MPa)	-	500	-
Cl-7.1, 7.2 & 7.3, Table-9(Rp0.2 MPa)	-	500	-
Cl-7.1, 7.2 & 7.3, Table-9(Elongation , Percent)	-	1500	-
Cl-9(Dimensions and Tolerances)	-	500	-
Cl-12(Packaging and Marking)	-	100	-
Cl-7.1(Tensile test)	-	2500	-
Cl-5(Freedom from Defects)	-	500	-
Cl-6.1, Table-1 to 8(Si)	-	500	-

05 Oct, 2028

-
Included w.e.f 09.03.2026

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

All

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
6(FREEDOM FROM DEFECTS)	-	1000	-
8(DIMENSIONS AND TOLERANCES)	-	500	-
10(MECHANICAL PROPERTIES)	-	7000	-
Cl. 9(Aluminium)	-	500	-
Cl. 9(Copper)	-	500	-
Cl. 9(Magnesium)	-	500	-
Cl. 9(Silicon)	-	500	-
Cl. 9(Iron)	-	500	-
Cl. 9(Manganese)	-	500	-
Cl. 9(Zinc)	-	500	-
Cl. 9(Titanium and/or other grain refining elements)	-	500	-
Cl. 9(Chromium)	-	500	-
Cl. 9(Ti+V)	-	500	-
Cl. 9(Cr+Mn)	-	500	-
Clause-10(Tensile strength)	-	2500	-
Clauses 9.2(Ni)	-	500	-
Clauses 9.2(Pb)	-	500	-
Clauses 9.2(Sn)	-	500	-
Clauses 9.2(Ag)	-	1000	-
Clauses 9.2(Be)	-	500	-
Clauses 9.2(Zr)	-	1500	-
Clauses 9.2(Co)	-	500	-

05 Oct, 2028

-
Included w.e.f 09.03.2026

IS 4246 (2025)

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION (Sixth Revision )

All type

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General - IS 4246 : 2025)	-	2000	-
4.1.1(General - IS 4246 : 2025)	-	2000	-
5(Materials - Cl. 5 of IS 5116)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1.1(Materials - Toughened glass, if provided,)	-	5000	-
5.1(Materials - IS 5116)	-	5000	-
5.1(Materials - IS 5116)	-	5000	-
5.1.1(Materials - IS 5116)	-	5000	-
5.1.1(Materials - IS 5116)	-	5000	-
5.2(Materials - IS 5116)	-	5000	-
5.2(Materials - IS 5116)	-	5000	-
5.3(Materials - IS 5116)	-	5000	-
5.5(Materials - IS 5116)	-	5000	-
5.5(Materials - IS 5116)	-	5000	-
5.5(Materials - IS 5116)	-	5000	-
5.7(Materials - IS 5116)	-	5000	-
6.1(Design for Maintainance)	-	5000	-
6.1(Design for Maintainance)	-	2000	-
6.2(Design for Maintainance)	-	2000	-
6.2(Design for Maintainance)	-	2000	-
6.3(Design for Maintainance)	-	2000	-
6.4(Design for Maintainance)	-	2000	-
6.5(Design for Maintainance)	-	2000	-
6.6(Design for Maintainance)	-	2000	-
7.0(Rigidity and Stability)	-	1000	-
7.1(Rigidity and Stability)	-	1000	-
7.2(Rigidity and Stability)	-	1000	-
7.3(Rigidity and Stability)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	2000	-
8.2(Workmanship and Finish -)	-	2000	-
8.3(Workmanship and Finish -)	-	2000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	2500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.2(Burners)	-	1000	-
11.3(Burners)	-	1000	-
11.4(Burners)	-	1000	-
12.1(Burner Pan Support)	-	1000	-
12.2(Burner Pan Support)	-	500	-
12.3(Burner Pan Support)	-	500	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	1500	-
13,2(Gas Soundness Test)	-	1500	-
13.2(Gas Leak Detector)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
4.1(General - IS 4246 : 2025)	-	5000	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.3(Gas Inlet Connection)	-	2000	-
14.4(Gas Inlet Connection)	-	2000	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	2000	-
14.6(Gas Inlet Connection)	-	2000	-
15.0(Strength and Rigidity)	-	1500	-
15.0(Strength and Rigidity)	-	1500	-
15.0(Strength and Rigidity)	-	1500	-
15.0(Strength and Rigidity)	-	1500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.2(Gas Consumption Test - For Gas Stoves)	-	4500	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	4500	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	4500	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	4500	-
17.3(Gas Consumption Test - For Built in Hobs)	-	4500	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	4500	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	4500	-
18.1(Ignition and Flame Travel)	-	1500	-
18.1(Ignition and Flame Travel)	-	1500	-
18.2(Ignition and Flame Travel)	-	1500	-
18.3(Ignition and Flame Travel)	-	1500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1500	-
19.1(Flame Stability)	-	1000	-
19.1.1(Flame Stability)	-	1000	-
19.2(Flame Stability)	-	1000	-
19.3(Flame Stability)	-	1000	-
20(Noise Control)	-	500	-
21(Flash Back)	-	500	-
22(Formation of Soot)	-	500	-
23(Resistance to Draught)	-	500	-
24.1(Combustion)	-	2500	-
24.1(Combustion)	-	2500	-
24.2(Combustion)	-	2500	-
25.1(Fire Hazard and Limiting Temperatures)	-	3500	-
25.1(Fire Hazard and Limiting Temperatures)	-	3500	-
25.1(Fire Hazard and Limiting Temperatures)	-	3500	-
25.1(Fire Hazard and Limiting Temperatures)	-	3500	-
25.2(Fire Hazard and Limiting Temperatures)	-	3500	-
26.1(Thermal Efficiency- Gas Stoves)	-	6000	-
26.1(Thermal Efficiency- Gas Stoves)	-	6000	-
26.1(Thermal Efficiency- Gas Stoves)	-	6000	-
26.1(Thermal Efficiency- Gas Stoves)	-	6000	-
26.1(Thermal Efficiency- Gas Stoves)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
4.1(General - IS 4246 : 2025)	-	4000	-
4.1.1(General - IS 4246 : 2025)	-	2500	-
5(Materials - Cl. 5 of IS 5116)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1.1(Materials - Toughened glass, if provided,)	-	3000	-
5.1(Materials - IS 5116)	-	3000	-
5.1(Materials - IS 5116)	-	3000	-
5.1.1(Materials - IS 5116)	-	3000	-
5.1.1(Materials - IS 5116)	-	3000	-
5.2(Materials - IS 5116)	-	3000	-
5.2(Materials - IS 5116)	-	3000	-
5.3(Materials - IS 5116)	-	3000	-
5.5(Materials - IS 5116)	-	3000	-
5.5(Materials - IS 5116)	-	3000	-
5.5(Materials - IS 5116)	-	3000	-
5.7(Materials - IS 5116)	-	3000	-
6.1(Design for Maintainance)	-	3000	-
6.1(Design for Maintainance)	-	2000	-
6.2(Design for Maintainance)	-	2000	-
6.2(Design for Maintainance)	-	2000	-
6.3(Design for Maintainance)	-	2000	-
6.4(Design for Maintainance)	-	2000	-
6.5(Design for Maintainance)	-	2000	-
6.6(Design for Maintainance)	-	2000	-
7.0(Rigidity and Stability)	-	1500	-
7.1(Rigidity and Stability)	-	1500	-
7.2(Rigidity and Stability)	-	1500	-
7.3(Rigidity and Stability)	-	1500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	1000	-
8.2(Workmanship and Finish -)	-	1000	-
8.3(Workmanship and Finish -)	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
10(Injector Jets)	-	1500	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.1(Burners- Cl. 10 of IS 5116)	-	1000	-
11.2(Burners)	-	1000	-
11.3(Burners)	-	1000	-
11.4(Burners)	-	1000	-
12.1(Burner Pan Support)	-	1000	-
12.2(Burner Pan Support)	-	1000	-
12.3(Burner Pan Support)	-	1000	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	1000	-
13,2(Gas Soundness Test)	-	2000	-
13.2(Gas Leak Detector)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	2000	-
4.1(General - IS 4246 : 2025)	-	1500	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.2(Gas Inlet Connection)	-	2000	-
14.3(Gas Inlet Connection)	-	2000	-
14.4(Gas Inlet Connection)	-	2000	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	2000	-
14.6(Gas Inlet Connection)	-	2000	-
15.0(Strength and Rigidity)	-	2500	-
15.0(Strength and Rigidity)	-	2500	-
15.0(Strength and Rigidity)	-	2500	-
15.0(Strength and Rigidity)	-	2500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.0(Gas Consumption Test)	-	4500	-
17.2(Gas Consumption Test - For Gas Stoves)	-	4500	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	4500	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	4500	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	4500	-
17.3(Gas Consumption Test - For Built in Hobs)	-	4500	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	4500	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	4500	-
18.1(Ignition and Flame Travel)	-	1000	-
18.1(Ignition and Flame Travel)	-	1000	-
18.2(Ignition and Flame Travel)	-	1000	-
18.3(Ignition and Flame Travel)	-	1000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1000	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	1000	-
19.1(Flame Stability)	-	1500	-
19.1.1(Flame Stability)	-	1500	-
19.2(Flame Stability)	-	1500	-
19.3(Flame Stability)	-	1500	-
20(Noise Control)	-	1500	-
21(Flash Back)	-	1500	-
22(Formation of Soot)	-	1500	-
23(Resistance to Draught)	-	1500	-
24.1(Combustion)	-	2000	-
24.1(Combustion)	-	2000	-
24.2(Combustion)	-	2000	-
25.1(Fire Hazard and Limiting Temperatures)	-	2500	-
25.1(Fire Hazard and Limiting Temperatures)	-	2500	-
25.1(Fire Hazard and Limiting Temperatures)	-	2500	-
25.1(Fire Hazard and Limiting Temperatures)	-	2500	-
25.2(Fire Hazard and Limiting Temperatures)	-	2500	-
26.1(Thermal Efficiency- Gas Stoves)	-	2500	-
26.1(Thermal Efficiency- Gas Stoves)	-	2500	-
26.1(Thermal Efficiency- Gas Stoves)	-	2500	-
26.1(Thermal Efficiency- Gas Stoves)	-	6000	-
26.1(Thermal Efficiency- Gas Stoves)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	6000	-

05 Oct, 2028

-
Included w.e.f 09.03.2026

IS 1660 (2024)

Wrought and Cast Aluminium Utensils Specification ( Second Revision )

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	3000	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	3000	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	3000	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	3000	-
Cl-4.1(Main body of utensil)	-	3000	-
Cl-4.1(Cast cookware)	-	3000	-
Cl-4.1(Other aluminum components and parts)	-	3000	-
Cl-4.1.1(Lids (material))	-	3000	-
Cl-4.1.1(Minimum thickness of lid)	-	3000	-
Cl-4.1.2(Minimum thickness of glass)	-	3000	-
Cl-4.1.2(Material of rim)	-	3000	-
Cl-4.1.2(Minimum thickness of rim)	-	3000	-
Cl-4.2(Material of strips)	-	3000	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	3000	-
Cl-4.3(Clips of lunch box)	-	3000	-
Cl-4.3(Clips of lunch box)	-	3000	-
Cl-4.3(Rivets used in lunch box)	-	3000	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	3000	-
Cl-4.5(Rivets for fixing of handles)	-	3000	-
Cl-4.5(Material of cap)	-	3000	-
Cl-4.6(Strips used for flame guards)	-	3000	-
Cl-4.6(stainless steel)	-	3000	-
Cl-5(Fabrication)	-	3000	-
Cl-6(Shape and Dimensions)	-	3000	-
Cl-7.1(Handles, when fitted)	-	3000	-
Cl-7.2(Handles)	-	3000	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	3000	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	3000	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	3000	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	3000	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	3000	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	3000	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	3000	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	3000	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	3000	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	3000	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	3000	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	3000	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	3000	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	3000	-
Cl-8(Workmanship and Finish)	-	3000	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	3000	-
Cl-8.3(Minimum nominal thickness)	-	3000	-
Cl-8.3(Thickness of hard anodized)	-	3000	-
Cl-8.3(Finish and appearance of hard anodized)	-	3000	-
Cl-8.3(Abrasion resistance of hard anodized)	-	3000	-
Cl-8.3(Colour of hard anodized)	-	3000	-
Cl-8.3(Hardness of hard anodized)	-	3000	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	3000	-
Cl-8.5(Non-stick unreinforced PTFE)	-	3000	-
Cl-8.6(Ceramic coating)	-	3000	-
Cl-8.7(The thickness test, adhesion test)	-	3000	-
Cl-8.7(Minimum thickness of coating)	-	3000	-
Cl-8.7.1(Dry heat the cookware)	-	3000	-
Cl-8.8(Requirements of PTFE)	-	3000	-
Cl-8.9(Material for induction plate)	-	3000	-
Cl-8.9(Test for Induction compatible base)	-	3000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	3000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	3000	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	3000	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	3000	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	3000	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	3000	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	3000	-
Cl-9.1(Normal Capacity)	-	3000	-
Cl-9.2(Normal Capacity of internal diameter)	-	3000	-
Cl 3.1.4 Table 3 (Amendment No.1)(Thickness of cast cookware- Cast Aluminium- Minimum Base Thickness of Body)	-	3000	-

05 Oct, 2028

-
-

IS 14756 (2024)

Stainless Steel Utensils - Specification (THIRD REVISION)

All Types

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Material used for manufacturing utensils)	-	30000	-
Cl 3.2(Material used for composite bottom)	-	30000	-
Cl 3.3(Material used for body of utensil of 3-ply construction)	-	30000	-
Cl 3.4(Material used for stainless steel lid)	-	30000	-
Cl 3.5(Material used for tempered glass lid)	-	30000	-
Cl 3.5(Material used for stainless steel rim)	-	30000	-
Cl 4.2 & Table 1(Minimum Sheet Thickness for Body of Utensil)	-	30000	-
Cl 4.2 & Table 2(Minimum Sheet Thickness for Lid of Utensil)	-	30000	-
Cl 4.2(Thickness of the finished utensil)	-	30000	-
Cl 4.3(Classification)	-	30000	-
Cl 4.4 (i)(Thickness of Aluminium disc/core)	-	30000	-
Cl 4.4 (ii)(Thickness of Protector/cowl)	-	30000	-
Cl 4.5(Minimum sheet thickness (3-ply utensil))	-	30000	-
Cl 4.5(Thickness of finished utensil (3-ply utensil))	-	30000	-
Cl 5.1(Manufacturing defect & visual appearance)	-	30000	-
CL 5.2(Accessibility for cleaning)	-	30000	-
Cl 5.3(Joining of handles to the utensils)	-	30000	-
Cl 5.4(Requirement for handles)	-	30000	-
Cl 5.5(Welding (Finish))	-	30000	-
Cl 5.6(Finish of 3-ply utensil)	-	30000	-
Cl 5.7(Requirement for coating)	-	30000	-
Cl 5.8(Coating thickness test)	-	30000	-
Cl 5.8(Coating adhesion test)	-	30000	-
Cl 5.8.1(Thermal shock test (Coating))	-	30000	-
Cl 6.1(Staining Test (Type Test - Frequency Once in a Year))	-	30000	-
Cl 6.2(Mechanical Shock Test (for Cladded Utensils Only))	-	30000	-
Cl 6.3(Thermal Shock Test (for Cladded Utensils Only))	-	30000	-
Cl 6.4(Dry Heat Test (for Cladded Utensils Only))	-	30000	-
Cl 6.5(Coating Thickness Test (for Copper Deposit))	-	30000	-
Cl 6.6(Thermal shock test (3-ply construction utensil body))	-	30000	-
Cl 6.7(Nominal Capacity Test)	-	30000	-
Cl 8(Marking)	-	30000	-

05 Oct, 2028

-
-

IS 18573 (2024)

Cold formed welded carbon steel square and rectangular hollow sections for mechanical, general engineering and decorative purposes ï¿½ Specification

ALL GRADES

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Types)	-	17000	-
Clause.4.0(Carbon)	-	17000	-
Clause.4.0(Sulphur)	-	17000	-
Clause.4.0(Sulphur)	-	17000	-
Clause.4.0(Phosphorus)	-	17000	-
Clause.4.0(Silicon)	-	17000	-
Clause.4.0(Manganese)	-	17000	-
Clause.5.0(Supply of Material)	-	17000	-
Clause.5.0(Supply of Material)	-	17000	-
Clause.6.0(Workmanship)	-	17000	-
Clause.7.0(Straightness)	-	17000	-
Clause.8.0(Basis of Calculation)	-	17000	-
Clause.9.0(Length)	-	17000	-
Clause.10.0(Dimensions and properties)	-	17000	-
Clause.10.0(Dimensions and properties)	-	17000	-
Clause.11.0(General)	-	17000	-
Clause.11.0(Outside Dimension)	-	17000	-
Clause.11.0(Thickness)	-	17000	-
Clause.11.0(Thickness)	-	17000	-
Clause.11.0(Concavity and Convexity)	-	17000	-
Clause.11.0(Squareness of Sides)	-	17000	-
Clause.11.0(External Corner Radiius)	-	17000	-
Clause.11.0(Straightness and twist)	-	17000	-
Clause.12.0(Dimension Tolerances)	-	17000	-
Clause.12.0(Dimension Tolerances)	-	17000	-
Clause.13.0(Surface Protection)	-	17000	-
Clause.14.0(Testing)	-	17000	-
Clause.15.0(Tensile test)	-	17000	-
Clause.15.0(Yield strength)	-	17000	-
Clause.15.0(Elognation Percent)	-	17000	-
Clause.18.0(Marking)	-	17000	-
6(Workmanship)	-	17000	-
10(Dimensions and Properties)	-	17000	-
11(Measurement of Shape and Size)	-	17000	-
12(Dimensions and Tolerances)	-	17000	-
13(Surface Protection)	-	17000	-
15(Tensile Test)	-	17000	-

05 Oct, 2028

-
-

IS 16218 (2014)

Forks - Specification

ALL

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(food grade stainless steel.)	-	12000	-
3.2 (i)(Brass as parent material)	-	12000	-
3.2(ii)(Brass plated with pure silver)	-	12000	-
3.3(Plastic handle)	-	12000	-
4(Shapes and Dimensions)	-	12000	-
5(Manufacture)	-	12000	-
6.1(Workmanship)	-	12000	-
6.2(Finish)	-	12000	-
9(Marking)	-	12000	-
10(Packing)	-	12000	-

05 Oct, 2028

-
-

IS 9730 (2008)

Non - Stick unreinforced plastics coatings on domestic cooking utensils - Specification (First Revision)

ALL TYPES

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	3000	-
4.2(Visual Defects)	-	3000	-
4.3 & 7.2(Thickness)	-	3000	-
4.4 & 7.3(Non-stick Quality)	-	3000	-
4.5 & 7.4(Salt Water Corrosion Resistance)	-	3000	-
4.6, 7.5.2 & 7.5.3(Adhesion Test)	-	3000	-
5(Marking)	-	3000	-
6(Instructions for use)	-	3000	-

05 Oct, 2028

-
-

IS 734 (1975)

Specification for wrought aluminium and aluminium alloy forging stock and forgings (For General Engineering Purposes) (Second Revision)

ALL DRADE/TYPES

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table 1(chemical composition)	-	10000	-
5.1 table 2(0.2% proof strength)	-	10000	-
5.1 table 2(Tensile strength)	-	10000	-
5.1 table 2(Elongation)	-	10000	-
Cl.5.1(Aluminium - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Titanium And/or Other Grain Refining Elements - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Remarks (Cu + Mg + Si + Fe + Mn + Zn) - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
4.1(Freedom from defects)	-	10000	-
9.1(Tensile test)	-	10000	-
5.1 table 1(chemical composition)	-	10000	-
5.1 table 2(0.2% proof strength)	-	10000	-
5.1 table 2(Tensile strength)	-	10000	-
5.1 table 2(Elongation)	-	10000	-
Cl.5.1(Aluminium - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Titanium And/or Other Grain Refining Elements - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
Cl.5.1(Remarks (Cu + Mg + Si + Fe + Mn + Zn) - IS 504 and its parts or any other intrumental/chemical methods)	-	10000	-
4.1(Freedom from defects)	-	10000	-
9.1(Tensile test)	-	10000	-

05 Oct, 2028

-
-

IS 15558 (2024)

INSTANTANEOUS DOMESTIC WATER HEATER FOR USE WITH LPG SPECIFICATION First Revision of IS 15558

ALL TYPES

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirements)	-	15000	-
Cl-5.1(water heater)	-	15000	-
Cl-5.2(copper and copper alloy)	-	15000	-
Cl-5.3(Non-metallic materials)	-	15000	-
Cl-5.4(Mixing tube and burner head)	-	15000	-
Cl-6.3(All Water connections)	-	15000	-
Cl-6.4(water inlet and outlet connections)	-	15000	-
Cl-6.6(Gas Inlet Connections)	-	15000	-
Cl-7(Flame visibility)	-	15000	-
Cl-8(Gas Taps)	-	15000	-
Cl-9(Flame failuse device)	-	15000	-
Cl-11(Protection against accidental overheating)	-	15000	-
Cl-13(General condition of test)	-	15000	-
Cl-14(Gas Soundness)	-	15000	-
Cl-15(Water Soundness)	-	15000	-
Cl-16(Thermal efficiency)	-	15000	-
Cl-17(carbon monoxide/carbon dioxide)	-	15000	-
Cl-18(Gas Consumption)	-	15000	-
Cl-19(Ignition and flame travel)	-	15000	-
Cl-20(FLAME STABILITY)	-	15000	-
Cl-21(NOISE CONTROL)	-	15000	-
Cl-22(FLASH-BACK)	-	15000	-
Cl-24("FIRE HAZARDS AND LIMITING TEMPERATURE")	-	15000	-
Cl-25(TIME FOR TEMPERATURE RISE)	-	15000	-
Cl-26(HOT WATER OUTPUT TEST)	-	15000	-

05 Oct, 2028

-
-

IS 18755 (2024)

Tri-ply SS-AL-SS material used for manufacture of utensils and kitchen appliances Specification

All types

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of material and designation)	-	15000	OK
Cl-5(Manufacturer)	-	15000	OK
Cl-6(Aluminium for use as matrix)	-	15000	OK
Cl-6(Top-surface of the aluminium matrix)	-	15000	OK
Cl-6(Bottom-surface of the aluminium matrix)	-	15000	OK
Cl-7.1.1(Tensile properties)	-	15000	OK
Cl-7.1.1(Apparent Yield Strength)	-	15000	OK
Cl-7.1.1(Tensile Strength Mpa,)	-	15000	OK
Cl-7.1.2(Test Specimen)	-	15000	OK
Cl-7.1.3(Test Parameters)	-	15000	OK
Cl-7.2.1(Bond strength of Tri-Ply)	-	15000	OK
Cl-7.2.2(Sample Preparation and Test Specimen)	-	15000	OK
Cl-7.2.3(Test Apparatus)	-	15000	OK
Cl-7.2.4(Procedure)	-	15000	OK
Cl-8.1(Sample of suitable size)	-	15000	OK
Cl-8.2(specimen for peel strength)	-	15000	OK
Cl-8.3, table-3(T-Peel Strength, N/mm, Min SS304 and Al 19500 interface)	-	15000	OK
Cl-8.3, table-3(T-Peel Strength, N/mm, Min SS430 and Al 19500 interface)	-	15000	OK
Cl-9.1(Thickness)	-	15000	OK
Cl-9.2(Diameter)	-	15000	OK
Cl-9.3(Flatness)	-	15000	OK
Cl-10(surface finish)	-	15000	OK
Cl-11(Workmanship, finish and appearance)	-	15000	OK
Cl-14(Marking)	-	15000	OK

05 Oct, 2028

-
-

IS 14756 (2024)

Stainless Steel Utensils - Specification (THIRD REVISION)

All Types

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Material used for manufacturing utensils)	-	30000	-
Cl 3.2(Material used for composite bottom)	-	30000	-
Cl 3.3(Material used for body of utensil of 3-ply construction)	-	30000	-
Cl 3.4(Material used for stainless steel lid)	-	30000	-
Cl 3.5(Material used for tempered glass lid)	-	30000	-
Cl 3.5(Material used for stainless steel rim)	-	30000	-
Cl 4.2 & Table 1(Minimum Sheet Thickness for Body of Utensil)	-	30000	-
Cl 4.2 & Table 2(Minimum Sheet Thickness for Lid of Utensil)	-	30000	-
Cl 4.2(Thickness of the finished utensil)	-	30000	-
Cl 4.3(Classification)	-	30000	-
Cl 4.4 (i)(Thickness of Aluminium disc/core)	-	30000	-
Cl 4.4 (ii)(Thickness of Protector/cowl)	-	30000	-
Cl 4.5(Minimum sheet thickness (3-ply utensil))	-	30000	-
Cl 4.5(Thickness of finished utensil (3-ply utensil))	-	30000	-
Cl 5.1(Manufacturing defect & visual appearance)	-	30000	-
CL 5.2(Accessibility for cleaning)	-	30000	-
Cl 5.3(Joining of handles to the utensils)	-	30000	-
Cl 5.4(Requirement for handles)	-	30000	-
Cl 5.5(Welding (Finish))	-	30000	-
Cl 5.6(Finish of 3-ply utensil)	-	30000	-
Cl 5.7(Requirement for coating)	-	30000	-
Cl 5.8(Coating thickness test)	-	30000	-
Cl 5.8(Coating adhesion test)	-	30000	-
Cl 5.8.1(Thermal shock test (Coating))	-	30000	-
Cl 6.1(Staining Test (Type Test - Frequency Once in a Year))	-	30000	-
Cl 6.2(Mechanical Shock Test (for Cladded Utensils Only))	-	30000	-
Cl 6.3(Thermal Shock Test (for Cladded Utensils Only))	-	30000	-
Cl 6.4(Dry Heat Test (for Cladded Utensils Only))	-	30000	-
Cl 6.5(Coating Thickness Test (for Copper Deposit))	-	30000	-
Cl 6.6(Thermal shock test (3-ply construction utensil body))	-	30000	-
Cl 6.7(Nominal Capacity Test)	-	30000	-
Cl 8(Marking)	-	30000	-

05 Oct, 2028

-
-

IS 13049 (1991)

diaphragm type (plastic body) float operated valves for cold water services

ALL TYPES

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(NOMINAL SIZE- )	-	35000	Ok
5-5.1-Table 1-Sr. no.1)(MATERIALS- Valve Body, Inlet Shank, Valve Seat and back Nut-Polyacetal)	-	35000	Ok
5-5.1-Table 1-Sr. no.2)(MATERIALS- Discharge horn (If Provided)-Polyacetal or polypropylene or polyethylene or Acrylnitrile Butadiene Styrene (ABS) or Ethylene Vinyl Acetate (EVA) or any other suitable material)	-	35000	Ok
5-5.1-Table 1-Sr. no.3)(MATERIALS- Discharge horn (If Provided)-Polyacetal or polypropylene or polyethylene or Acrylnitrile Butadiene Styrene (ABS) or Ethylene Vinyl Acetate (EVA) or any other suitable material)	-	35000	Ok
5-5.2(MATERIALS)	-	35000	Ok
5-5.2(MATERIALS)	-	35000	Ok
6-6.1(MANUFACTURE AND WORKMANSHIP)	-	35000	Ok
6-6.2(MANUFACTURE AND WORKMANSHIP)	-	35000	Ok
7-7.1(CONSTRUCTION-Inlet Connection- The inlet shank shall be not less than 48 mm In length.)	-	35000	Ok
7-7.1-Annex A(CONSTRUCTION-Inlet Connection- External screw on inlet connections shall be such as to meet the test requirements of Annex A.)	-	35000	Ok
7-7.2-7.2.1(CONSTRUCTION-Seats and body)	-	35000	Ok
7-7.2-7.2.2(CONSTRUCTION-Seats and body-In case of detachable type of seats, colour ccding as given below shall be followed ;)	-	35000	Ok
7-7.2-7.2.2(CONSTRUCTION-Seats and body-In case of detachable type of seats, colour ccding as given below shall be followed ;)	-	35000	Ok
7-7.2-7.2.3(CONSTRUCTION-Seats and body-The distance between the seat outlet orifice and the shutting off face of the diaphragm shall be 15 mm, Min in the fully opened position.)	-	35000	Ok
7-7.3(CONSTRUCTION-Diaphragm-Diaphragms made of synthetic rubber shall have the form and dimensions as required for the operation of the valve.)	-	35000	Ok
7-7.4(CONSTRUCTION-Back Nuts-Annex A)	-	35000	Ok
7-7.4(CONSTRUCTION-Back Nuts-Threads on backnuts shall also comply WIth the test requirements of Annex A.)	-	35000	Ok
7-7.5(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.1(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.2(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Initial Deflection shall not be more than 25 mm)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Additiononal deflection after loading for 28 days as specified in Annex B shall not be more than 12 mm)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Total deflection thus shall not he more than 37 mm)	-	35000	Ok
7-7.6-7.6.1(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
7-7.6-7.6.2(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
7-7.6-7.6.3(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
8-8.1(PERFORMANCE TEST-Hydraulic Test)	-	35000	Ok
8-8.2(PERFORMANCE TEST-Shut Off Test-Annex C)	-	35000	Ok
8-8.3(PERFORMANCE TEST-Antisiphonage Test-Annex D)	-	35000	Ok
8-8.4(PERFORMANCE TEST-Flow Test- Annex E)	-	35000	Ok
8-8.5(PERFORMANCE TEST-Endurance Test-Annex F)	-	35000	Ok
8-8.6(PERFORMANCE TEST-Test for Hydraulic Pressure on Discbarge Arrangements-Annex G)	-	35000	Ok
4(NOMINAL SIZE- )	-	35000	Ok
5-5.1-Table 1-Sr. no.1)(MATERIALS- Valve Body, Inlet Shank, Valve Seat and back Nut-Polyacetal)	-	35000	Ok
5-5.1-Table 1-Sr. no.2)(MATERIALS- Discharge horn (If Provided)-Polyacetal or polypropylene or polyethylene or Acrylnitrile Butadiene Styrene (ABS) or Ethylene Vinyl Acetate (EVA) or any other suitable material)	-	35000	Ok
5-5.1-Table 1-Sr. no.3)(MATERIALS- Discharge horn (If Provided)-Polyacetal or polypropylene or polyethylene or Acrylnitrile Butadiene Styrene (ABS) or Ethylene Vinyl Acetate (EVA) or any other suitable material)	-	35000	Ok
5-5.2(MATERIALS)	-	35000	Ok
5-5.2(MATERIALS)	-	35000	Ok
6-6.1(MANUFACTURE AND WORKMANSHIP)	-	35000	Ok
6-6.2(MANUFACTURE AND WORKMANSHIP)	-	35000	Ok
7-7.1(CONSTRUCTION-Inlet Connection- The inlet shank shall be not less than 48 mm In length.)	-	35000	Ok
7-7.1-Annex A(CONSTRUCTION-Inlet Connection- External screw on inlet connections shall be such as to meet the test requirements of Annex A.)	-	35000	Ok
7-7.2-7.2.1(CONSTRUCTION-Seats and body)	-	35000	Ok
7-7.2-7.2.2(CONSTRUCTION-Seats and body-In case of detachable type of seats, colour ccding as given below shall be followed ;)	-	35000	Ok
7-7.2-7.2.2(CONSTRUCTION-Seats and body-In case of detachable type of seats, colour ccding as given below shall be followed ;)	-	35000	Ok
7-7.2-7.2.3(CONSTRUCTION-Seats and body-The distance between the seat outlet orifice and the shutting off face of the diaphragm shall be 15 mm, Min in the fully opened position.)	-	35000	Ok
7-7.3(CONSTRUCTION-Diaphragm-Diaphragms made of synthetic rubber shall have the form and dimensions as required for the operation of the valve.)	-	35000	Ok
7-7.4(CONSTRUCTION-Back Nuts-Annex A)	-	35000	Ok
7-7.4(CONSTRUCTION-Back Nuts-Threads on backnuts shall also comply WIth the test requirements of Annex A.)	-	35000	Ok
7-7.5(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.1(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.2(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Initial Deflection shall not be more than 25 mm)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Additiononal deflection after loading for 28 days as specified in Annex B shall not be more than 12 mm)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Total deflection thus shall not he more than 37 mm)	-	35000	Ok
7-7.6-7.6.1(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
7-7.6-7.6.2(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
7-7.6-7.6.3(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
8-8.1(PERFORMANCE TEST-Hydraulic Test)	-	35000	Ok
8-8.2(PERFORMANCE TEST-Shut Off Test-Annex C)	-	35000	Ok
8-8.3(PERFORMANCE TEST-Antisiphonage Test-Annex D)	-	35000	Ok
8-8.4(PERFORMANCE TEST-Flow Test- Annex E)	-	35000	Ok
8-8.5(PERFORMANCE TEST-Endurance Test-Annex F)	-	35000	Ok
8-8.6(PERFORMANCE TEST-Test for Hydraulic Pressure on Discbarge Arrangements-Annex G)	-	35000	Ok
4(NOMINAL SIZE- )	-	35000	Ok
5-5.1-Table 1-Sr. no.1)(MATERIALS- Valve Body, Inlet Shank, Valve Seat and back Nut-Polyacetal)	-	35000	Ok
5-5.1-Table 1-Sr. no.2)(MATERIALS- Discharge horn (If Provided)-Polyacetal or polypropylene or polyethylene or Acrylnitrile Butadiene Styrene (ABS) or Ethylene Vinyl Acetate (EVA) or any other suitable material)	-	35000	Ok
5-5.1-Table 1-Sr. no.3)(MATERIALS- Discharge horn (If Provided)-Polyacetal or polypropylene or polyethylene or Acrylnitrile Butadiene Styrene (ABS) or Ethylene Vinyl Acetate (EVA) or any other suitable material)	-	35000	Ok
5-5.2(MATERIALS)	-	35000	Ok
5-5.2(MATERIALS)	-	35000	Ok
6-6.1(MANUFACTURE AND WORKMANSHIP)	-	35000	Ok
6-6.2(MANUFACTURE AND WORKMANSHIP)	-	35000	Ok
7-7.1(CONSTRUCTION-Inlet Connection- The inlet shank shall be not less than 48 mm In length.)	-	35000	Ok
7-7.1-Annex A(CONSTRUCTION-Inlet Connection- External screw on inlet connections shall be such as to meet the test requirements of Annex A.)	-	35000	Ok
7-7.2-7.2.1(CONSTRUCTION-Seats and body)	-	35000	Ok
7-7.2-7.2.2(CONSTRUCTION-Seats and body-In case of detachable type of seats, colour ccding as given below shall be followed ;)	-	35000	Ok
7-7.2-7.2.2(CONSTRUCTION-Seats and body-In case of detachable type of seats, colour ccding as given below shall be followed ;)	-	35000	Ok
7-7.2-7.2.3(CONSTRUCTION-Seats and body-The distance between the seat outlet orifice and the shutting off face of the diaphragm shall be 15 mm, Min in the fully opened position.)	-	35000	Ok
7-7.3(CONSTRUCTION-Diaphragm-Diaphragms made of synthetic rubber shall have the form and dimensions as required for the operation of the valve.)	-	35000	Ok
7-7.4(CONSTRUCTION-Back Nuts-Annex A)	-	35000	Ok
7-7.4(CONSTRUCTION-Back Nuts-Threads on backnuts shall also comply WIth the test requirements of Annex A.)	-	35000	Ok
7-7.5(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.1(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.2(CONSTRUCTION-Floats, Float Arm and Assembly-)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Initial Deflection shall not be more than 25 mm)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Additiononal deflection after loading for 28 days as specified in Annex B shall not be more than 12 mm)	-	35000	Ok
7-7.5-7.5.3(CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Total deflection thus shall not he more than 37 mm)	-	35000	Ok
7-7.6-7.6.1(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
7-7.6-7.6.2(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
7-7.6-7.6.3(CONSTRUCTION-Discharge Arrangements)	-	35000	Ok
8-8.1(PERFORMANCE TEST-Hydraulic Test)	-	35000	Ok
8-8.2(PERFORMANCE TEST-Shut Off Test-Annex C)	-	35000	Ok
8-8.3(PERFORMANCE TEST-Antisiphonage Test-Annex D)	-	35000	Ok
8-8.4(PERFORMANCE TEST-Flow Test- Annex E)	-	35000	Ok
8-8.5(PERFORMANCE TEST-Endurance Test-Annex F)	-	35000	Ok
8-8.6(PERFORMANCE TEST-Test for Hydraulic Pressure on Discbarge Arrangements-Annex G)	-	35000	Ok

05 Oct, 2028

-
-

IS 12234 (2021)

Plastic equilibrium float valves for cold water services - Specification (first revision)

All types

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Materials)	-	35000	Ok
6(Manufacture and Workmanship)	-	35000	Ok
7.1 to 7.3 , 7.6 to 7.9(Construction)	-	35000	Ok
7.4 to 7.5 and 7.10(Dimensions, Screw threads and Back nut)	-	35000	Ok
8.1.1, 8.1.2(Hydraulic and Shut-Off Test)	-	35000	Ok
8.2 Appendix-A(Antisiphonage Test)	-	35000	Ok
8.3 Appendix-B(Flow Test)	-	35000	Ok
8.4 Appendix-C(Endurance Test)	-	35000	Ok
10(Marking)	-	35000	Ok

05 Oct, 2028

-
-

IS 16286 (2014)

Spoons - Specification

All Types

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(food grade stainless steel.)	-	14500	Ok
3.2 (i)(Brass as parent material)	-	14500	Ok
3.2(ii)(Brass plated with pure silver)	-	14500	Ok
3.3(Plastic handle)	-	14500	Ok
4(Shapes and Dimensions)	-	14500	Ok
5.1(Manufacture)	-	14500	Ok
5.2(Workmanship)	-	14500	Ok
5.3(Finish)	-	14500	Ok
8(Marking)	-	14500	Ok
9(Packing)	-	14500	Ok
Cl-6.1(Staining Test)	-	14500	Ok
Cl-6.2(Bending Test)	-	14500	Ok
Cl-6.3(Load Test)	-	14500	Ok
Cl-6.4.1(Boiling)	-	14500	Ok
Cl-6.4.2(Impact)	-	14500	Ok
Cl-6.4.3(Staining)	-	14500	Ok

05 Oct, 2028

-
-

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

ALL

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Ordering Information - IS 737)	-	20000	-
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	20000	-
Cl. 4 (b)(Condition - IS 737)	-	20000	-
Cl. 4 (c)(Quantity in Kg - IS 737)	-	20000	-
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	20000	-
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	20000	-
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	20000	-
Cl. 4 (g)(Packing Mode - IS 737)	-	20000	-
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	20000	-
Cl. 6(Freedom from Defects - IS 737)	-	20000	-
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	20000	-
Cl. 7(Al - IS 504)	-	20000	-
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	20000	-
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	20000	-
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	20000	-
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	20000	-
Cl. 8.2(Bend Test - IS 1599)	-	20000	-
Cl. 9(Condition - IS 737/ IS 5052)	-	20000	-
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	20000	-
Cl. 11(Selection of Test Samples - IS 737)	-	20000	-
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	20000	-
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	20000	-
Cl. 12(Retests - IS 737/ IS 10259)	-	20000	-
Cl. 13(Packaging - IS 737/ IS 10259)	-	20000	-
Cl. 13.1(Marking - IS 737)	-	20000	-

05 Oct, 2028

-
-

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

All Grades

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Freedom from defects)	-	20000	-
7.0(Dimension and Tolerances)	-	20000	-
8.1 Table-1(Al)	-	20000	-
8.1 Table-1(Cu)	-	20000	-
8.1 Table-1(Mg)	-	20000	-
8.1 Table-1(Si)	-	20000	-
8.1 Table-1(Fe)	-	20000	-
8.1 Table-1(Mn)	-	20000	-
8.1 Table-1(Zn)	-	20000	-
8.1 Table-1(Ti)	-	20000	-
8.1 Table-1(Cr)	-	20000	-
9.1(Tensile Strength)	-	20000	-
9.3(Wrapping Test)	-	20000	-
10(Selection of Test Samples)	-	20000	-

05 Oct, 2028

-
-

IS 8931 (2021)

Copper alloy single taps, combination tap assemblies, stop valves and single lever mixers for water services Specification (second revision)

Pillar Tap, Bib Tap, Combination Tap Assembly, Stop Valve, Angle Stop Valve, Single Level mixer

38000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Classfication)	-	38000	Ok
Cl 4(Classfication)	-	38000	Ok
Cl 6.1(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.5(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.6(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.7(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.8(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.9(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.10(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.11(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.12(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 6.13(Manufacture,Workmanship & Construction)	-	38000	Ok
Cl 7(DIMENSIONS)	-	38000	Ok
Cl 7(DIMENSIONS)	-	38000	Ok
Cl 7(DIMENSIONS)	-	38000	Ok
Cl 7(DIMENSIONS)	-	38000	Ok
Cl 7(DIMENSIONS)	-	38000	Ok
Cl 8(ADDITIONAL REQUIREMENTS FOR ACCESSIBLE TAPS)	-	38000	Ok
Cl 10(PERFORMANCE REQUIREMENTS)	-	38000	Ok
Cl 10(PERFORMANCE REQUIREMENTS)	-	38000	Ok
Cl 10(PERFORMANCE REQUIREMENTS)	-	38000	Ok
Cl 10(PERFORMANCE REQUIREMENTS)	-	38000	Ok
Cl 10(PERFORMANCE REQUIREMENTS)	-	38000	Ok
Cl 11(ADDITIONAL REQUIREMENTS FOR WATER EFFICIENCY)	-	38000	Ok
As per Table-1(Carbon)	-	38000	Ok
As per Table-1(Sulphur)	-	38000	Ok
As per Table-1(Phosphorus)	-	38000	Ok
As per Table-1(Manganese)	-	38000	Ok
As per Table-1(Nitrogen)	-	38000	Ok
As per Table-1(Silicon)	-	38000	Ok
As per Table-1(Aluminium)	-	38000	Ok
As per Table-1(Chromium)	-	38000	Ok
As per Table-1(Vanadium)	-	38000	Ok
As per Table-1(Molybdenum)	-	38000	Ok
As per Table-1(Iron)	-	38000	Ok
As per Table-1(Nickel)	-	38000	Ok
As per Table-1(Copper)	-	38000	Ok
As per Table-1(Zinc)	-	38000	Ok
As per Table-1(Lead)	-	38000	Ok
As per Table-1(Boron)	-	38000	Ok

05 Oct, 2028

-
-

IS 1264 (1997)

Brass gravity die castings - Specification (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	15000	-
6.0(Shape)	-	15000	-
6.0(Size)	-	15000	-
6.0(Mass)	-	15000	-
7.0(Cu)	-	15000	-
7.0(Sn)	-	15000	-
7.0(Pb)	-	15000	-
7.0(Ni)	-	15000	-
7.0(Fe)	-	15000	-
7.0(Al)	-	15000	-
7.0(Mn)	-	15000	-
7.0(Si)	-	15000	-
7.0(Total impurities excluding Ni Pb Al Zn)	-	15000	-
9.0(Pressure test)	-	15000	-
11(Marking)	-	15000	-
11(Marking)	-	15000	-

05 Oct, 2028

-
-

IS 6603 (2024)

Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars â Specification (Second Revision)

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl - 9.1,9.5,13.2(Thickness or Diameter)	-	55000	-
Cl - 9.1,9.5,13.2(Proof Strength Rp 0.2 MP)	-	55000	-
Cl - 9.1,9.5,13.2(Proof Strength Rp 1.0 MP)	-	55000	-
Cl - 9.1,9.5,13.2(Tensile Strength)	-	55000	-
Cl - 9.1,9.5,13.2(Elongation After Fracture Long.)	-	55000	-
Cl - 9.1,9.5,13.2(Elongation After Fracture Tr.)	-	55000	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V) Long.)	-	55000	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V) Tr.)	-	55000	-
Cl - 9.1,9.5,13.2(Resistance to Inter-Granular Corrosion in the Delivery Condition)	-	55000	-
Cl - 9.1,9.5,13.2(Resistance to Inter-Granular Corrosion in the Sensitized Condition)	-	55000	-
Cl - 9.1,9.5,13.2(Hardness)	-	55000	-
Cl - 9.1,9.5,13.2(Elongation After Fracture)	-	55000	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Thickness or Diameter)	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R MPa Max(Annealed))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Hardness HB Max(Annealed))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Heat Treatment Condition (Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R 0.2 MPa Min(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R Mpa(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Long.(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Tr.(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Thickness or Diameter)	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R MPa Max(Annealed))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Hardness HB Max(Annealed))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(Heat Treatment Condition (Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R 0.2 MPa Min(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(R Mpa(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Long.(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Tr.(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	55000	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 450 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 500 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 550 Deg. C)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 100 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 150 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 200 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 250 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 300 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 350 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 400 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 450 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 550 Deg. C.)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	55000	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	55000	-

05 Oct, 2028

-
-

IS 302 : Part 2 : SEC 31 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 31 range hoods

34000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	34000	-
Clause No - 5.18(linear and angular dimension)	-	34000	-
Clause No - 6.2(harmfull ingress of water)	-	34000	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	34000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	34000	-
Clause No - 8.2(Addition)	-	34000	-
Clause No - 10.1, Table No. -1(power input deviation)	-	34000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	34000	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	34000	-
Clause No - 14(Impulse test voltage)	-	34000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	34000	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	34000	-
Clause No -19.11.4.1(electrostatic discharge)	-	34000	-
Clause No -19.11.4.2(radiated field)	-	34000	-
Clause No -19.11.4.3(fast transient)	-	34000	-
Clause No -19.11.4.4(Voltage dips and interruption)	-	34000	-
Clause No -21.1(Mechanical strength)	-	34000	-
Clause No -22.1(construction)	-	34000	-
Clause No -22.11(push force applied)	-	34000	-
Clause No -24.1.2(safety isolating transformer)	-	34000	-
Clause No -24.1.3(for switches)	-	34000	-
Clause No -24.1.4(for automatic control)	-	34000	-
Clause No -24.1.5(for innterconnection couplers)	-	34000	-
Clause No -24.4(plug and socket)	-	34000	-
Clause No -25.8, Table no -11(conductor resistance)	-	34000	-
Clause No -25.5(dimension for pins)	-	34000	-
Clause No -27.6(for circuit board)	-	34000	-
Clause No -29.2(comparative tracking index)	-	34000	-
Clause No -29.3.3(dry heat test)	-	34000	-
Clause No -30.2.1(glow wire test)	-	34000	-
Clause No -30.101("incorporate combustible material")	-	34000	-

05 Oct, 2028

-
-

IS 617 (2024)

Aluminium and Aluminium Alloys Ingots for Remelting and Castings for General Engineering Purposes â Specification (Fourth Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1, Table-1(Si)	-	6000	-
Cl-6.1, Table-1(Fe)	-	6000	-
Cl-6.1, Table-1(Cu)	-	6000	-
Cl-6.1, Table-1(Mn)	-	6000	-
Cl-6.1, Table-1(Mg)	-	6000	-
Cl-6.1, Table-1(Cr)	-	6000	-
Cl-6.1, Table-1(Ni)	-	6000	-
Cl-6.1, Table-1(Zn)	-	6000	-
Cl-6.1, Table-1(Pb)	-	6000	-
Cl-6.1, Table-1(Sn)	-	6000	-
Cl-6.1, Table-1(Ti)	-	6000	-
Cl-6.1, Table-1(Others elements Each)	-	6000	-
Cl-6.1, Table-1(Others elements Total)	-	6000	-
Cl-6.1, Table-1(Aluminium)	-	6000	-
Cl-6.2(The chemical analysis)	-	6000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Tensile Strength)	-	6000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Proof Stress)	-	6000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Elongation)	-	6000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Brinell Hardness HBW)	-	6000	-
Cl-7.1, Table-3(Chill Cast Alloys- Tensile Strength)	-	6000	-
Cl-7.1, Table-3(Chill Cast Alloys- Proof Stress)	-	6000	-
Cl-7.1, Table-3(Chill Cast Alloys- Elongation)	-	6000	-
Cl-7.1, Table-3(Chill Cast Alloys- Brinell Hardness HBW)	-	6000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Tensile Strength)	-	6000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Proof Stress)	-	6000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Elongation)	-	6000	-
Cl-7.1, Table-4(Investment-Cast Alloys-Brinell Hardness)	-	6000	-
Cl-7.2(Tensile Tests)	-	6000	-
Cl-7.3(Test Pieces)	-	6000	-
Cl-7.4(Hardness)	-	6000	-
Cl-8(Freedom from Defects)	-	6000	-
Cl-11(RETEST)	-	6000	-
Cl-13(Marking)	-	6000	-
Cl-6.1, Table-1(Si)	-	6000	-
Cl-6.1, Table-1(Fe)	-	6000	-
Cl-6.1, Table-1(Cu)	-	6000	-
Cl-6.1, Table-1(Mn)	-	6000	-
Cl-6.1, Table-1(Mg)	-	6000	-
Cl-6.1, Table-1(Cr)	-	6000	-
Cl-6.1, Table-1(Ni)	-	6000	-
Cl-6.1, Table-1(Zn)	-	6000	-
Cl-6.1, Table-1(Pb)	-	6000	-
Cl-6.1, Table-1(Sn)	-	6000	-
Cl-6.1, Table-1(Ti)	-	6000	-
Cl-6.1, Table-1(Others elements Each)	-	6000	-
Cl-6.1, Table-1(Others elements Total)	-	6000	-
Cl-6.1, Table-1(Aluminium)	-	6000	-
Cl-6.2(The chemical analysis)	-	6000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Tensile Strength)	-	6000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Proof Stress)	-	6000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Elongation)	-	6000	-
Cl-7.1, Table-2(Sand-Cast Alloys- Brinell Hardness HBW)	-	6000	-
Cl-7.1, Table-3(Chill Cast Alloys- Tensile Strength)	-	6000	-
Cl-7.1, Table-3(Chill Cast Alloys- Proof Stress)	-	6000	-
Cl-7.1, Table-3(Chill Cast Alloys- Elongation)	-	6000	-
Cl-7.1, Table-3(Chill Cast Alloys- Brinell Hardness HBW)	-	6000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Tensile Strength)	-	6000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Proof Stress)	-	6000	-
Cl-7.1, Table-4(Investment-Cast Alloys- Elongation)	-	6000	-
Cl-7.1, Table-4(Investment-Cast Alloys-Brinell Hardness)	-	6000	-
Cl-7.2(Tensile Tests)	-	6000	-
Cl-7.3(Test Pieces)	-	6000	-
Cl-7.4(Hardness)	-	6000	-
Cl-8(Freedom from Defects)	-	6000	-
Cl-11(RETEST)	-	6000	-
Cl-13(Marking)	-	6000	-

05 Oct, 2028

-
-

IS/ISO 9994 (2018)

Lighters Safety specifications First Revision

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.6, 6.6.3.1(Refilling test-IS/ISO 9994)	-	17000	Ok
6.6, 6.6.3.2(Refilling test-IS/ISO 9994)	-	17000	Ok
Cl.4(Flame Generation)	-	17000	Ok
Cl.4.2(Flame Height)	-	17000	Ok
Cl.4.3(Flame-Height adjustment)	-	17000	Ok
Cl.4.4(Resistance to spitting or sputtering and flaring)	-	17000	Ok
Cl.4.5(Flame Extinction)	-	17000	Ok
Cl.4.6(Volumetric displacement of Fuel)	-	17000	Ok
Cl.4.7(Mass of Fuel)	-	17000	Ok
Cl.5.1(External Finish)	-	17000	Ok
Cl.5.2(Compatibility of Fuel)	-	17000	Ok
Cl.5.3(Resistance to Fuel Loss)	-	17000	Ok
Cl.5.4(Resistance to dropping)	-	17000	Ok
Cl.5.5(Resistance to elevated Temperature)	-	17000	Ok
Cl.5.6(Resistance to internal Pressure)	-	17000	Ok
Cl.5.7(Burning Behavior)	-	17000	Ok
Cl.5.8(Resistance to cyclic burning)	-	17000	Ok
Cl.5.9(Resistance to Continue Burning)	-	17000	Ok

05 Oct, 2028

-
-

IS 617 (1994)

Cast aluminium and its alloys - Ingots and castings for general engineering purposes - Specification (Third Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(TOLERANCES ON DIMENSIONS OF CASTINGS)	-	20000	-
7(FREEDOM FROM DEFECTS)	-	20000	-
6.2(Hardness)	-	20000	-
6, Table 2.(MECHANICAL PROPERTIES OF CASTINGS)	-	20000	-
5, Table 1.(Chemical Composition)	-	20000	-
17(Marking)	-	20000	-
11()	-	20000	-
11(Pressure Test)	-	20000	-
17(Marking)	-	20000	-
11(Pressure Test)	-	20000	-
11(Pressure Test - IS 617)	-	20000	-
13(Marking)	-	20000	-
Table-1, Clause - 5.1(Copper)	-	20000	-
Table-1, Clause - 5.1(Iron)	-	20000	-
Table-1, Clause - 5.1(Magnesium)	-	20000	-
Table-1, Clause - 5.1(Manganese)	-	20000	-
Table-1, Clause - 5.1(Tin)	-	20000	-
Table-1, Clause - 5.1(Silicon)	-	20000	-
Table-1, Clause - 5.1(Nickel)	-	20000	-
Table-1, Clause - 5.1(Zinc)	-	20000	-
Table-1, Clause - 5.1(Other elements (each))	-	20000	-
Table-1, Clause - 5.1(Other elements (Total))	-	20000	-
Table-1, Clause - 5.1(Aluminium)	-	20000	-
Table-1, Clause - 5.1(Titanium)	-	20000	-
Table-1, Clause - 5.1(Lead)	-	20000	-
9(TOLERANCES ON DIMENSIONS OF CASTINGS)	-	20000	-
7(FREEDOM FROM DEFECTS)	-	20000	-
6.2(Hardness)	-	20000	-
6, Table 2.(MECHANICAL PROPERTIES OF CASTINGS)	-	20000	-
5, Table 1.(Chemical Composition)	-	20000	-
17(Marking)	-	20000	-
11()	-	20000	-
11(Pressure Test)	-	20000	-
17(Marking)	-	20000	-
11(Pressure Test)	-	20000	-
11(Pressure Test - IS 617)	-	20000	-
13(Marking)	-	20000	-
Table-1, Clause - 5.1(Copper)	-	20000	-
Table-1, Clause - 5.1(Iron)	-	20000	-
Table-1, Clause - 5.1(Magnesium)	-	20000	-
Table-1, Clause - 5.1(Manganese)	-	20000	-
Table-1, Clause - 5.1(Tin)	-	20000	-
Table-1, Clause - 5.1(Silicon)	-	20000	-
Table-1, Clause - 5.1(Nickel)	-	20000	-
Table-1, Clause - 5.1(Zinc)	-	20000	-
Table-1, Clause - 5.1(Other elements (each))	-	20000	-
Table-1, Clause - 5.1(Other elements (Total))	-	20000	-
Table-1, Clause - 5.1(Aluminium)	-	20000	-
Table-1, Clause - 5.1(Titanium)	-	20000	-
Table-1, Clause - 5.1(Lead)	-	20000	-

05 Oct, 2028

-
-

IS 15355 (2018)

Rubber hoses and hose assemblies for liquefied petroleum gas (L.p.g) in motor vehicles - Specification (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 ,TABLE 1(Internal diameter)	-	40000	-
5.2(Concentricity)	-	40000	-
5.3(Length)	-	40000	-
6.1(Performance requirements)	-	40000	-
6.2(Visual examination)	-	40000	-
6.3(Rubber compounds)	-	40000	-
6.4(Finished hose)	-	40000	-
7.1(Requirements for fittings)	-	40000	-
7.2(Requirements for fittings)	-	40000	-
8.1(Gas leakage)	-	40000	-
8.2(Minimum burst pressure)	-	40000	-
8.3(Visual examination)	-	40000	-
9.1(Marking)	-	40000	-
9.2(Marking)	-	40000	-
5.1 ,TABLE 1(Internal diameter)	-	40000	-
5.2(Concentricity)	-	40000	-
5.3(Length)	-	40000	-
6.1(Performance requirements)	-	40000	-
6.2(Visual examination)	-	40000	-
6.3(Rubber compounds)	-	40000	-
6.4(Finished hose)	-	40000	-
7.1(Requirements for fittings)	-	40000	-
7.2(Requirements for fittings)	-	40000	-
8.1(Gas leakage)	-	40000	-
8.2(Minimum burst pressure)	-	40000	-
8.3(Visual examination)	-	40000	-
9.1(Marking)	-	40000	-
9.2(Marking)	-	40000	-
6.3, Table 2(Minimum Tensile Strength-Lining - ISO 37)	-	40000	-
6.3, Table 2(Minimum Tensile Strength-Cover - ISO 37)	-	40000	-
6.3, Table 2(Minimum Elongation at Break -Lining - ISO 37)	-	40000	-
6.3, Table 2(Minimum Elongation at Break -Cover - ISO 37)	-	40000	-
6.3, Table 2(Resistance to Ageing (3 days at (100±1)²C using the air-oven method in ISO 188:2007- Change in Tensile strength from original value -Lining (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to Ageing (3 days at (100±1)²C using the air-oven method in ISO 188:2007- Change in Tensile strength from original value -Cover (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to Ageing (3 days at (100±1)²C using the air-oven method in ISO 188:2007- Change in Elongation at break from original value -Lining - ISO 37)	-	40000	-
6.3, Table 2(Resistance to Ageing (3 days at (100±1)²C using the air-oven method in ISO 188:2007- Change in Elongation at break from original value -Cover - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Tensile strength from original value -Lining (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Tensile strength from original value -Cover (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Elongation at break from original value -Lining (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Elongation at break from original value -Cover (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Volume-Lining (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Volume-Cover (±, max) - ISO 37)	-	40000	-
6.4, Table 3(Proof Pressure- ISO 1402, hold for 10 miniute)	-	40000	-
6.4, Table 3(Minimum Burst Pressure -ISO 1402)	-	40000	-
6.4, Table 3(Adhesion between lining and reinforcement and between reinforcement and cover (min) - ISO 8033)	-	40000	-
6.4, Table 3(Ozone Resistance -ISO 7326:2006, method 2 ; Ozone concentration (100±5) parts per million ; Temperature (40±1) °C and 50±5 % Relative Humidity for 72 h at 20% Elongation)	-	40000	-
6.4, Table 3(Low Temperature flexibility - ISO 4672-1997, method B at ( -40 ± 2 )°C)	-	40000	-
6.4, Table 3(Permeability to propane gas (max) - ISO 4080-2009, method 3 ; use hose size 19 for test , adjust waterbath temperature to maintain a hose pressure of ( 1 ± 0.02 ) Mpa (0.007 cm³/(m².s) or 36.0 cm³/m of hose in 24 h)	-	40000	-
6.3, Table 2(Minimum Tensile Strength-Lining - ISO 37)	-	40000	-
6.3, Table 2(Minimum Tensile Strength-Cover - ISO 37)	-	40000	-
6.3, Table 2(Minimum Elongation at Break -Lining - ISO 37)	-	40000	-
6.3, Table 2(Minimum Elongation at Break -Cover - ISO 37)	-	40000	-
6.3, Table 2(Resistance to Ageing (3 days at (100±1)²C using the air-oven method in ISO 188:2007- Change in Tensile strength from original value -Lining (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to Ageing (3 days at (100±1)²C using the air-oven method in ISO 188:2007- Change in Tensile strength from original value -Cover (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to Ageing (3 days at (100±1)²C using the air-oven method in ISO 188:2007- Change in Elongation at break from original value -Lining - ISO 37)	-	40000	-
6.3, Table 2(Resistance to Ageing (3 days at (100±1)²C using the air-oven method in ISO 188:2007- Change in Elongation at break from original value -Cover - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Tensile strength from original value -Lining (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Tensile strength from original value -Cover (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Elongation at break from original value -Lining (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Elongation at break from original value -Cover (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Volume-Lining (±, max) - ISO 37)	-	40000	-
6.3, Table 2(Resistance to n-Pentane (Immersion for 72 hours att (23±2)²C in accordance with ISO 1817 - Change in Volume-Cover (±, max) - ISO 37)	-	40000	-
6.4, Table 3(Proof Pressure- ISO 1402, hold for 10 miniute)	-	40000	-
6.4, Table 3(Minimum Burst Pressure -ISO 1402)	-	40000	-
6.4, Table 3(Adhesion between lining and reinforcement and between reinforcement and cover (min) - ISO 8033)	-	40000	-
6.4, Table 3(Ozone Resistance -ISO 7326:2006, method 2 ; Ozone concentration (100±5) parts per million ; Temperature (40±1) °C and 50±5 % Relative Humidity for 72 h at 20% Elongation)	-	40000	-
6.4, Table 3(Low Temperature flexibility - ISO 4672-1997, method B at ( -40 ± 2 )°C)	-	40000	-
6.4, Table 3(Permeability to propane gas (max) - ISO 4080-2009, method 3 ; use hose size 19 for test , adjust waterbath temperature to maintain a hose pressure of ( 1 ± 0.02 ) Mpa (0.007 cm³/(m².s) or 36.0 cm³/m of hose in 24 h)	-	40000	-

05 Oct, 2028

-
-

IS 737 (2008)

Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes - Specification (Fourth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	8000	-
6 Table-1(Al)	-	8000	-
6 Table-1(Cu)	-	8000	-
6 Table-1(Mg)	-	8000	-
6 Table-1(Si)	-	8000	-
6 Table-1(Fe)	-	8000	-
6 Table-1(Mn)	-	8000	-
6 Table-1(Zn)	-	8000	-
6 Table-1(Ti)	-	8000	-
6 Table-1(Cr)	-	8000	-
6 Table-1(Cu+Si+Fe)	-	8000	-
6 Table-1(Cu+Si+Fe+Mn+Zn)	-	8000	-
6 Table-1(Cu+Mg+Si+Fe+Mn+Zn)	-	8000	-
6 Table-1(Zr)	-	8000	-
6 Table-1(Cr+Mn)	-	8000	-
7 Table-2(Tensile Strength)	-	8000	-
7 Table-2(Elongation)	-	8000	-
7 Table-2(0.2 % Proof Stress)	-	8000	-
7 Table-2(Bend Test)	-	8000	-
9(Dimension - IS 2676)	-	8000	-
12(Marking)	-	8000	-
9(Dimension - IS 2676)	-	8000	-
12(Marking)	-	8000	-

05 Oct, 2028

-
-

IS 6912 (2005)

Copper and copper alloys forging stock and forging - Specification (Second Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SUPPLY OF MATERIAL)	-	6000	-
Cl. No.6(Freedom from defects)	-	6000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	6000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	6000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	6000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	6000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	6000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	6000	-
Cl.no.9(Mechanical properties)	-	6000	-
Cl.no.10(Forgability Test)	-	6000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	6000	-
Cl. No.15(Marking)	-	6000	-
Cl. No.4(SUPPLY OF MATERIAL)	-	6000	-
Cl. No.6(Freedom from defects)	-	6000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	6000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	6000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	6000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	6000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	6000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	6000	-
Cl.no.9(Mechanical properties)	-	6000	-
Cl.no.10(Forgability Test)	-	6000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	6000	-
Cl. No.15(Marking)	-	6000	-

05 Oct, 2028

-
-

IS 10908 (2023)

FLEXIBLE RUBBER TUBING FOR LIQUEFIED PETROLEUM GAS SPECIFICATION Second Revision

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(The materials used in the manufacture of tubing shall be homogeneous and shall be resistant to outdoor exposure.)	-	20000	-
4.1(The tubing made out of this material shall be green in colour and shall be supplied normally in cut lengths or in rolls of running length)	-	20000	-
4.1("when supplied in cut lengths, the pieces shall be of minimum 1.0 m to maximum of 1.5 m in length. ")	-	20000	-
4.2(The walls shall be seamless and free from all visible defects, such as lumps, blow-holes, cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas.)	-	20000	-
4.3.1(The tubing when supplied in 6.4 mm inside diameter; the tolerance as per table-1)	-	20000	-
4.3.1(The tubing when supplied in 7.00 mm inside diameter; the tolerance as per table-1)	-	20000	-
4.3.2(It shall comply with thickness as given in Table 1, when measured according to IS 443 (Part 8). The readings shall be taken on a set of six test pieces cut from different sample sections.(For Wall thickness 3.20 mm))	-	20000	-
4.3.2(It shall comply with thickness as given in Table 1, when measured according to IS 443 (Part 8). The readings shall be taken on a set of six test pieces cut from different sample sections.(For Wall thickness 3.50 mm))	-	20000	-
4.4.1(When tested in accordance with the method given in Annex B, the tubing shall fit over the standard and oversize metal nozzle shown in Fig. 1, 2 and 3.)	-	20000	-
4.4.2("When tested in accordance with the method given in Annex B, the tubing shall remain attached to both nozzles throughout the test period. ")	-	20000	-
4.5(When immersed in water for 5 min under an internal air pressure of 0.25 MPa or 250 kPa (2.5 bar), the increase in the outside diameter or the tubing shall not be more than 15 percent.)	-	20000	-
4.5(When immersed in water for 5 min under an internal air pressure of 0.25 MPa or 250 kPa (2.5 bar), there shall be no sign of leakage in the tubing. Also the same shall not burst when the pressure is increased to 0.5 MPa or 500 kPa (5 bar), The test shall be carried out on a length of 60 cm.)	-	20000	-
4.6(The hardness on the flat surface of the cut/slit tubing shall be measured as prescribed in IS 3400 (Part 2/Sec 4), the shore hardness shall be 60 ± 5°A.)	-	20000	-
4.7("The flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100 °C for 72 h in accordance with the normal method prescribed in IS 3400 (Part 4). It shall not show a change of + 10° A of its original shore hardness value (see 4.6) after accelerated ageing")	-	20000	-
4.8.1("The tubing shall be immersed for 72 h in liquid pentane and then conditioned at room temperature for 24 h, after which it shall be tested in accordance with the method prescribed in Annex C, the gas pressure shown on the manometer shall not drop by more than 1 kPa")	-	20000	-
4.8.2(The tubing shall be so flexible that it will make contact with a cylindrical former of radius 68 mm for at least 110° of its circumference when the immersed tubing is placed over the former and a mass of 1.6 kg is attached to each end.)	-	20000	-
4.9(60 cm long tubing shall be subjected to a crushing force of 350 N applied on the middle of the tubing evenly over a length of 25 mm for 5 minutes, and 30 min after removal of the force it shall not show any deformation or collapse, nor shall it leak when subjected to an internal air pressure of 250 kPa)	-	20000	-
4.10(When tested in accordance with Annex D, the npentane absorbed shall not exceed 15 percent of the initial mass of the tubing and the amount of npentane extractable matter shall not exceed 10 percent of the initial mass of tubing.)	-	20000	-
4.11("When tested in accordance with the method described in Annex E, the slit tube shall not show any breakage on surface or cracks or defects.")	-	20000	-
4.12("When tested in accordance with the method described in Annex F, the tubing shall not burn to either of the outer marks within the test period of 45 s")	-	20000	-

05 Oct, 2028

-
-

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	15000	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	15000	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	15000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	15000	-
10(Tensile test)	-	15000	-

05 Oct, 2028

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Shri Krishna Test House

Plot No 88, Sector -E, Bawana-II, DSIIDC Industrial complex New Delhi, Delhi, Shahdara, Delhi, 110040

9891112786 skth1234@gmail.com

Scope List