BIS - LIMS (Laboratory Information Management System)

Shri Krishna Test House

B-70/1, Gali no 8 , New modern Shahdara ,Near DDA Flats mansarover park shahdara, Delhi, Shahdara, Delhi, 110032

9891112786 skth1234@gmail.com

Scope List

Reset

39 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 447 (1988)

Specification for rubber hose for welding (Fourth Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.2 - Table 1(Bore size)	-	100	NA
Cl. 3.2 - Table 1(Lining Thickness)	-	100	NA
Cl. 3.2 - Table 1(Cover Thickness)	-	100	NA
Cl. 3.2 - Table 1(Length %)	-	100	NA
Cl. 3.3 - Table 2(Tensile strength - Lining MPA)	-	500	NA
Cl. 3.3 - Table 2(Tensile strength - Cover Mpa)	-	500	NA
Cl. 3.3 - Table 2(Elongation at break - Lining %)	-	500	NA
Cl. 3.3 - Table 2(After Ageing Tensile strength - Lining %)	-	500	NA
Cl. 3.3 - Table 2(After Ageing Tensile strength - Cover %)	-	500	NA
Cl. 3.3 - Table 2(After Ageing Elongation at break - Lining %)	-	500	NA
Cl. 3.3 - Table 2(After Ageing Elongation at break - Cover)	-	500	NA
Cl. 3.4 - Table3(Pressure Tests)	-	1000	NA
Cl. 3.4 - Table3(Adhesion, KN/m Min)	-	1000	NA

Complete

05 Oct, 2025

IS 12585 (1988)

Specification for thermoplastic hoses (Textile Reinforced) for water - General purpose

7313 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(Types)	-	2000	NA
Cl 4.1(Construction)	-	2000	NA
Cl 4.2(Dimensions & Tolerances)	-	2000	NA
Cl 4.3.1 & Appendix A(Loss in Mass on Heating)	-	2000	NA
Cl 4.3.2(Adhesion)	-	500	NA
Cl 4.3.3(Pressure Requirements)	-	500	NA
Cl 4.3.4(Minimum Bend Radius)	-	1000	NA
Cl 4.3.5(Low Temperature Flexibility)	-	2000	NA

Complete

05 Oct, 2025

IS 10908 (1991)

Flexible rubber tubing for liquefied petroleum gas - Specification (First Revision)

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1 (The tubing made out of this material shall be green in colour )	-	100	NA
Cl.4.2(The walls shall be seamless and free from all visible such as lumps, blows-holes,cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas)	-	100	NA
Cl4.3.1(The tubing shall be supplied in 6.4 and 7.0 mm inisde diametre,The tolerance on nominal diamtere shall be as per table 1)	-	200	NA
Cl4.3.2(it shall comply with the thickness as givien in table 1 when measured according to 4.2.2 of IS 443;1975 The readings shall be taken from different sample sections.)	-	200	NA
Cl.4.4,(Cl.4.4.1)(when tested in accordance with the method given in AnnexureA. It shall fit over the standard and oversize metal nozzle shown in Fig1,2 and 3)	-	200	NA
Cl.4.4,(Cl.4.4.2)(it shall remain atatched to both nozzles throught the test period)	-	200	NA
Cl.4.5(When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the increase in the outside diametre of the tubing ,Also the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-	1200	NA
Cl.4.6(Shore Hardness: the hardnesss on the flatsurface of the cut/slit tubing shall be measured and the same shall be 60 ± 5˚A)	-	1500	NA
Cl.4.7(Accelerated Ageing test, the flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100Deg Cfor 72 hours in accordance with the method prescribed in IS 3400 (Part 4) it shall not show a change of + 10 A of its orignal shore hardness )	-	1500	NA
Cl.4.8.1(Flexible test , Annexure B The gas pressure shown on the manometre shall not drop by more than 1 Kpa)	-	500	NA
Cl4.8.2(The tubing shall be so flexible that it will make contact with a cylinder former of radius 68 mm for at least 110 deg of its circumference when the tubing is placed over the framer and a mass of 1.6 kg is attcahed to each end)	-	800	NA
Cl.4.9(Crushing test , )	-	1000	NA
Cl.4.10(Resistance to lpg ,Annexure c Shall not be more than 15 % of the initial mass of the tubing and the amount of exctractable matter shall not excced 10 percent of the iniital mass of te tubing)	-	1500	NA
Cl.4.11(Resistance to Ozone ,Annexure D Shall not show any breakage on surface or crack or defects)	-	2000	NA
Cl.4.12(Burning behaviour on exposure to small flame,Annexure E tubing shall not burn to either of the outer marks within the test period of 45 seconds)	-	500	NA

Complete

05 Oct, 2025

IS 21 (1992)

Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2, Table 1of IS:21 (Designation 19000)(Copper)	-	400	NA
4.2, Table 1of IS:21 (Designation 19000)(Magnesium)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Silicon)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Iron)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Manganese)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Zinc)	-	400	-
4.2, Table 1of IS:21 (Designation 19000)(Aluminium)	-	200	-
4.2, Table 1of IS:21 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	200	-
4.2, Table 1of IS:21 (Designation 19000)(Lead)	-	200	-
4.2, Table 1of IS:21 (Designation 19500)(Copper)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Silicon)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Iron)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Manganese)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Zinc)	-	400	-
4.2, Table 1of IS:21 (Designation 19500)(Lead)	-	200	-
4.2, Table 1of IS:21 (Designation 19500)(Cu+Si+Fe+Mn+Zn)	-	200	-
4.2, Table 1of IS:21 (Designation 19500)(Aluminium)	-	600	-
4.2, Table 1of IS:21 (Designation 19600)(Copper)	-	400	-
4.2, Table 1of IS:21 (Designation 19600)(Silicon)	-	400	-
4.2, Table 1of IS:21 (Designation 19600)(Iron)	-	400	-
4.2, Table 1of IS:21 (Designation 19600)(Manganese)	-	500	-
4.2, Table 1of IS:21 (Designation 19600)(Zinc)	-	500	-
4.2, Table 1of IS:21 (Designation 19600)(Lead)	-	400	-
4.2, Table 1of IS:21 (Designation 19600)(Cu+Si+Fe+Mn+Zn)	-	200	-
4.2, Table 1of IS:21 (Designation 19600)(Aluminium)	-	200	-
4.2, Table 1of IS:21 (Designation 31000)(Copper)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Magnesium)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Silicon)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Iron)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Manganese)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Zinc)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Titanium and or other grain refining elements)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Chromium)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Lead)	-	400	-
4.2, Table 1of IS:21 (Designation 31000)(Aluminium)	-	400	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Tensile Strength)	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Bend Test (Radius of Bend))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Tensile Strength)	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Bend Test (Radius of Bend))	-	500	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(0.2 Percent Proof Stress)	-	500	-

Complete

05 Oct, 2025

IS 7231 (2021)

Plastic flushing cisterns for water closets and urinals - Specification (third revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Materials)	-	12000	NA
5.2.1(Concealed Cistern- Construction)	-	500	NA
5.2.1(Concealed Cistern)	-	500	NA
5.1.7.3(Overflow Pipe)	-	500	NA
5.1.7.2(Overflow Pipe)	-	500	NA
5.1.7(Overflow Pipe)	-	500	NA
5.1.3.1(Flush pipe connection to cistern)	-	500	NA
5.1.6(Operating Mechanism (Push-Knob))	-	500	NA
5.1.5(Float Valve)	-	500	NA
5.1.4(Inlet and Overflow Holes)	-	500	NA
5.1.3.1(Flush pipe connection to cistern)	-	500	NA
5.1.3.1(Flush pipe connection to cistern)	-	500	NA
5.1.3.1(Flush pipe connection to cistern)	-	500	NA
5.1.3(Construction of Flush Pipe)	-	500	NA
5.1.2(Construction of Cover)	-	500	NA
5.1.1(Construction of Exposed Cistern)	-	500	NA
5.1.1(Construction of Exposed Cistern)	-	500	NA
5.1.1(Construction of Exposed Cistern)	-	500	NA
5.2.2(Flush Pipe)	-	500	NA
5.2.3(Operating Mechanism)	-	500	NA
5.2.3(Operating Mechanism)	-	500	NA
6, 6.1(Finish)	-	500	NA
6.1(Finish)	-	500	NA
6.1(Finish)	-	2000	NA
6.2(Finish)	-	500	NA
7.1(Operational and Performance Requirement- Flushing Arrangement)	-	500	NA
7.2(Working Water Level)	-	500	NA
7.3(Freedom from Leakage)	-	500	NA
7.4(Reduced Water Level)	-	500	NA
7.5 (a)(Cistern Discharge Capacity 6/3 Litres)	-	500	NA
7.5 (a)(Cistern Discharge Capacity 6/3 Litres)	-	500	NA
7.5 (b)(Cistern Discharge Capacity 4.8/2.8 litres)	-	500	NA
7.5 (b)(Cistern Discharge Capacity 4.8/2.8 litres)	-	500	NA
7.5 (c)(Cistern Discharge Capacity 4/2 litres)	-	500	NA
7.6 (a)(Discharge Rate)	-	500	NA
7.6 (b)(Discharge Rate)	-	500	NA
7.6 (c)(Discharge Rate)	-	500	NA
7.6(Discharge Rate)	-	500	NA
8.1(Distortion Resistance Test)	-	500	NA
8.2(Dead Load Test)	-	500	NA
8.3(Front Thrust Test)	-	500	NA
8.4(Impact Test)	-	500	NA
8.4.1(Impact Test)	-	200	NA
9.3(Endurance Test)	-	1000	NA

Complete

05 Oct, 2025

IS 13983 (1994)

Stainless Steel Sinks For Domestic Purposes

21500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking)	-	500	NA
4(Type)	-	500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Carbon Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Silicon Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Manganese Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nickel Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Chromium Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Sulphur Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Phouphorous Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nitrogen Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Carbon Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Silicon Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Manganese Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Nickel Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Chromium Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Sulphur Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Phouphorous Content)	-	1500	NA
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-07-Cr-18-Ni-9 (Numeric Symbol 302)(Nitrogen Content)	-	1500	NA
6(Thickness of sheet/strip)	-	1000	NA
6(Depth of bowl)	-	1000	NA
6(Internal dimensions of the bowl)	-	1000	NA
6(Bowl locating limits)	-	1000	NA
6(Co-ordinating sizes)	-	1000	NA
7.1(Consruction and workmanship)	-	1000	NA
7.3(Drainers)	-	500	NA
7.4(Waste outlet)	-	500	NA
7.5(Tap holes)	-	200	NA
7.6(Overflows)	-	200	NA
8(Finish)	-	1100	NA

Complete

05 Oct, 2025

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Heat Treatment)	-	2500	NA
Cl 9(Tensile & Hardness)	-	4500	NA
Cl 10(Diameter & Out Of Round)	-	2000	NA
6(The wire rods shall be smooth on surface and free from harmful surface defects)	-	200	-
7, Table 1of IS:6527 (Designation X04Cr13)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr13)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr13)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr13)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr13)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr13)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr13)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr13)(Aluminium)	-	200	-
7, Table 1of IS:6527 (Designation X04Cr13)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr13)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X12Cr13)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X12Cr13)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X12Cr13)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Carbon)	-	400	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Silicon)	-	400	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Manganese)	-	400	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Nickel)	-	400	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Niobium)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Titanium)	-	300	-
Cl 8(Heat Treatment)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(%Elongation)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(Ultimate Tensile Strength)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr17Ni12Mo2)(0.2% Proof Stress)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr17Ni12Mo2)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr17Ni12Mo2)(%Elongation)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr17Ni12Mo2)(Ultimate Tensile Strength)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr17Ni12Mo2)(0.2% Proof Stress)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X07Cr18Ni9)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X07Cr18Ni9)(%Elongation)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X07Cr18Ni9)(Ultimate Tensile Strength)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X07Cr18Ni9)(0.2% Proof Stress)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr18Ni10)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr18Ni10)(%Elongation)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr18Ni10)(Ultimate Tensile Strength)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr18Ni10)(0.2% Proof Stress)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr18Ni11)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr18Ni11)(%Elongation)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr18Ni11)(Ultimate Tensile Strength)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X02Cr18Ni11)(0.2% Proof Stress)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X30Cr13)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X30Cr13)(Ultimate Tensile Strength)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X20Cr13)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X20Cr13)(Ultimate Tensile Strength)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X12Cr13)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X12Cr13)(%Elongation)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X12Cr13)(Ultimate Tensile Strength)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X12Cr13)(0.2% Proof Stress)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr13)(Hardness)	-	500	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr13)(%Elongation)	-	200	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr13)(Ultimate Tensile Strength)	-	200	-
9, Table 3 & 4 of IS:6527 (Designation X04Cr13)(0.2% Proof Stress)	-	200	-
10 & 10.1, Dia over 20 mm (Out of round)	-	200	-
10 & 10.1, Dia- (5.5-9.5 mm)(Size, Tolerance)	-	200	-
10 & 10.1, Dia- (5.5-9.5 mm)(Out of round)	-	200	-
10 & 10.1, Dia over 9.5 mm upto 16 mm (Size, Tolerance)	-	200	-
10 & 10.1, Dia over 9.5 mm upto 16 mm (Out of round)	-	200	-
10 & 10.1, Dia over 16 mm upto 20 mm (Size, Tolerance)	-	200	-
10 & 10.1, Dia over 16 mm upto 20 mm (Out of round)	-	200	-
10 & 10.1, Dia over 20 mm (Size, Tolerance)	-	200	-
Cl 10(Diameter & Out Of Round)	-	200	-
7, Table 1of IS:6527 (Designation X12Cr13)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X12Cr13)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X12Cr13)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X12Cr13)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X12Cr13)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X12Cr13)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X20Cr13)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X30Cr13)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Niobium)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr18Ni11)(Titanium)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Niobium)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr18Ni10)(Titanium)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X07Cr18Ni9)(Titanium)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Niobium)	-	300	-
7, Table 1of IS:6527 (Designation X04Cr17Ni12Mo2)(Titanium)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X02Cr17Ni12Mo2)(Niobium)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Carbon)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Silicon)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Manganese)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Nickel)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Chromium)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Sulphur)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Phosphorous)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Nitrogen)	-	500	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Copper)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Molybdenum)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Niobium)	-	300	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4)(Titanium)	-	300	-

Complete

05 Oct, 2025

IS 13395 (2021)

Performance of Handles and Handle Assemblies Attached to Cookware - Specification ( First Revision )

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	2000	NA
5.2(Bending Strength)	-	2000	NA
5.3(Torque Strength)	-	2000	NA
5.4(Impact Strength)	-	2000	NA
5.5(Fatigue Resistance)	-	2000	NA
5.6(Leakage)	-	2000	NA
5.7(Thermal Insulation)	-	2000	NA
5.8(Heat Resistance)	-	2000	NA
5.9(Washing Resistance)	-	2000	NA
5.1(Burning Resistance)	-	2000	NA
4.1(Construction)	-	500	NA
4.2(Materials)	-	500	NA
4.3(Selection and Size)	-	500	NA
4.4(Position of handle and knob with respect to cookware)	-	500	NA
4.5(Attachment to cookware)	-	500	NA
5.1(General)	-	500	NA
5.2(Bending strength)	-	1000	NA
5.3(Torque strength)	-	1000	NA
5.4(Impact strength)	-	1000	NA
5.5(Fatigue resistance)	-	1000	NA
5.6(Leakage)	-	1000	NA
5.7(Thermal insulation)	-	1000	NA
5.8(Heat resistance)	-	1000	NA
5.9(Washing resistance)	-	1000	NA
5.10(Burning resistance)	-	1000	NA

Complete

05 Oct, 2025

IS 444 (2017)

Rubber hoses, textile - Reinforced, for general - Purpose water applications - Specification (Fifth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Lining - IS 444)	-	500	NA
6.1- Table 1(Internal diameters - ISO 4671)	-	500	NA
6.2(Concentricity - ISO 4671)	-	500	NA
6.3(Length -IS 4671)	-	500	NA
6.4( thickness of the lining plus cover - ISO 4671)	-	500	NA
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	500	NA
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	1000	NA
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	1000	NA
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	1000	NA
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	1200	NA
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	1200	NA
7.1 - Table 2(Change in tensile strength of Cover from original value after ageing(max) - ISO 188 and ISO 37)	-	1200	NA
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	1200	NA
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	1200	NA
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	2000	NA
4(Classification - IS 444)	-	1000	NA
5(Reinforcement - IS 444)	-	500	NA
5(Cover - IS 444)	-	500	NA
5(Lining and Cover - IS 444)	-	500	NA

Complete

05 Oct, 2025

Bureau of Indian Standards

The National Standards Body of India

Shri Krishna Test House

B-70/1, Gali no 8 , New modern Shahdara ,Near DDA Flats mansarover park shahdara, Delhi, Shahdara, Delhi, 110032

9891112786 skth1234@gmail.com

Scope List