| 5131 |
Gravitas Laboratories Private Limited, Greater Noida
| 8182606
| IS 7904 (2018) |
High carbon steel wire rods - Specification (Second Revision) |
- |
10000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Table-1,(Clauses 5.1 and 7.2)(S+P) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Nitrogen) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Titanium) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Vanadium) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Boron) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Copper) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Molybdenum) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Nickel) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Chromium) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Aluminium) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Silicon) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Manganese) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Phosphorous) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Sulphor) |
- |
500 |
|
- |
| Table-1,(Clauses 5.1 and 7.2)(Carbon) |
- |
500 |
|
- |
| Cl 9 (Dimensions & tolerances)() |
- |
500 |
|
- |
| 9(Dimesion (Diameter)) |
- |
500 |
|
- |
| 9(Dimesion (Out of Roundness)) |
- |
500 |
|
- |
| 10(Mechanical Properties (Tensile strength)) |
- |
1500 |
|
- |
| 10(Mechanical Properties (Reduction in Area)) |
- |
800 |
|
- |
| 12(Surface Defects) |
- |
500 |
|
- |
| 13(Decarburization Test) |
- |
1500 |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thin, worse)) |
- |
1500 |
|
- |
| 14(Type B (Alumina Type) (Thin, worse)) |
- |
600 |
|
- |
| 14(Type C (Silicate Type) (Thin, worse)) |
- |
600 |
|
- |
| 14(Type D( Globular Oxide Type ) (Thin, worse)) |
- |
600 |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thin, Mean)) |
- |
600 |
|
- |
| 14(Type B (Alumina Type) (Thin, Mean)) |
- |
600 |
|
- |
| 14(Type C (Silicate Type) (Thin, Mean)) |
- |
600 |
|
- |
| 14(Type D( Globular Oxide Type ) (Thin, Mean)) |
- |
600 |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thick, worse)) |
- |
600 |
|
- |
| 14(Type B (Alumina Type) (Thick, worse)) |
- |
600 |
|
- |
| 14(Type C (Silicate Type) (Thick, worse)) |
- |
600 |
|
- |
| 14(Type D( Globular Oxide Type ) (Thick, worse)) |
- |
600 |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thick, Mean)) |
- |
600 |
|
- |
| 14(Type B (Alumina Type) (Thick, Mean)) |
- |
600 |
|
- |
| 14(Type C (Silicate Type) (Thick, Mean)) |
- |
600 |
|
- |
| 14(Type D( Globular Oxide Type ) (Thick, Mean)) |
- |
600 |
|
- |
| 15(Microstructure) |
- |
600 |
|
- |
| 16(Axial Segregation (Optional)) |
- |
600 |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
600 |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
600 |
|
- |
| TABLE 1 NOTE 6() |
- |
600 |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
600 |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
600 |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
600 |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
600 |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
600 |
|
- |
| TABLE 1 NOTE 6() |
- |
600 |
|
- |
| TABLE 1 NOTE 1(Niobium) |
- |
600 |
|
- |
| TABLE 1 NOTE 1(Micro Alloy Element (Nb+V+Ti)) |
- |
600 |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
600 |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
600 |
|
- |
| Cl 9 (Dimensions & tolerances)() |
- |
0 |
|
- |
| 9(Dimesion (Diameter)) |
- |
0 |
|
- |
| 9(Dimesion (Out of Roundness)) |
- |
0 |
|
- |
| 10(Mechanical Properties (Tensile strength)) |
- |
0 |
|
- |
| 10(Mechanical Properties (Reduction in Area)) |
- |
0 |
|
- |
| 12(Surface Defects) |
- |
0 |
|
- |
| 13(Decarburization Test) |
- |
0 |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thin, worse)) |
- |
0 |
|
- |
| 14(Type B (Alumina Type) (Thin, worse)) |
- |
0 |
|
- |
| 14(Type C (Silicate Type) (Thin, worse)) |
- |
0 |
|
- |
| 14(Type D( Globular Oxide Type ) (Thin, worse)) |
- |
0 |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thin, Mean)) |
- |
0 |
|
- |
| 14(Type B (Alumina Type) (Thin, Mean)) |
- |
0 |
|
- |
| 14(Type C (Silicate Type) (Thin, Mean)) |
- |
0 |
|
- |
| 14(Type D( Globular Oxide Type ) (Thin, Mean)) |
- |
0 |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thick, worse)) |
- |
0 |
|
- |
| 14(Type B (Alumina Type) (Thick, worse)) |
- |
0 |
|
- |
| 14(Type C (Silicate Type) (Thick, worse)) |
- |
0 |
|
- |
| 14(Type D( Globular Oxide Type ) (Thick, worse)) |
- |
0 |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thick, Mean)) |
- |
0 |
|
- |
| 14(Type B (Alumina Type) (Thick, Mean)) |
- |
0 |
|
- |
| 14(Type C (Silicate Type) (Thick, Mean)) |
- |
0 |
|
- |
| 14(Type D( Globular Oxide Type ) (Thick, Mean)) |
- |
0 |
|
- |
| 15(Microstructure) |
- |
0 |
|
- |
| 16(Axial Segregation (Optional)) |
- |
0 |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
0 |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
0 |
|
- |
| TABLE 1 NOTE 6() |
- |
0 |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
0 |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
0 |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
0 |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
0 |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
0 |
|
- |
| TABLE 1 NOTE 6() |
- |
0 |
|
- |
| TABLE 1 NOTE 1(Niobium) |
- |
0 |
|
- |
| TABLE 1 NOTE 1(Micro Alloy Element (Nb+V+Ti)) |
- |
0 |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
0 |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
0 |
|
- |
| Cl 9 (Dimensions & tolerances)() |
- |
- |
|
- |
| 9(Dimesion (Diameter)) |
- |
- |
|
- |
| 9(Dimesion (Out of Roundness)) |
- |
- |
|
- |
| 10(Mechanical Properties (Tensile strength)) |
- |
- |
|
- |
| 10(Mechanical Properties (Reduction in Area)) |
- |
- |
|
- |
| 12(Surface Defects) |
- |
- |
|
- |
| 13(Decarburization Test) |
- |
- |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thin, worse)) |
- |
- |
|
- |
| 14(Type B (Alumina Type) (Thin, worse)) |
- |
- |
|
- |
| 14(Type C (Silicate Type) (Thin, worse)) |
- |
- |
|
- |
| 14(Type D( Globular Oxide Type ) (Thin, worse)) |
- |
- |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thin, Mean)) |
- |
- |
|
- |
| 14(Type B (Alumina Type) (Thin, Mean)) |
- |
- |
|
- |
| 14(Type C (Silicate Type) (Thin, Mean)) |
- |
- |
|
- |
| 14(Type D( Globular Oxide Type ) (Thin, Mean)) |
- |
- |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thick, worse)) |
- |
- |
|
- |
| 14(Type B (Alumina Type) (Thick, worse)) |
- |
- |
|
- |
| 14(Type C (Silicate Type) (Thick, worse)) |
- |
- |
|
- |
| 14(Type D( Globular Oxide Type ) (Thick, worse)) |
- |
- |
|
- |
| 14(Non-metallic Inclusions (Type A (Sulphide Type) (Thick, Mean)) |
- |
- |
|
- |
| 14(Type B (Alumina Type) (Thick, Mean)) |
- |
- |
|
- |
| 14(Type C (Silicate Type) (Thick, Mean)) |
- |
- |
|
- |
| 14(Type D( Globular Oxide Type ) (Thick, Mean)) |
- |
- |
|
- |
| 15(Microstructure) |
- |
- |
|
- |
| 16(Axial Segregation (Optional)) |
- |
- |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
- |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
- |
|
- |
| TABLE 1 NOTE 6() |
- |
- |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
- |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
- |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
- |
|
- |
| TABLE 1 NOTE 1(Any Validated test method) |
- |
- |
|
- |
| TABLE 1 NOTE 1(By Calculation) |
- |
- |
|
- |
| TABLE 1 NOTE 6() |
- |
- |
|
- |
| TABLE 1 NOTE 1(Niobium) |
- |
- |
|
- |
| TABLE 1 NOTE 1(Micro Alloy Element (Nb+V+Ti)) |
- |
- |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
- |
|
- |
| TABLE 1 NOTE 6(Tramp Element (Cr+ Ni+ Mo+ Cu)) |
- |
- |
|
- |
|
- |
-
Included w.e.f 02.06.2025 |
| 5132 |
Gravitas Laboratories Private Limited, Greater Noida
| 8182606
| IS 7902 (2001) |
Aluminium alloy forging stock and forgings (Alloy 24345) for aerospace applications - Specification (First Revision) |
All grades |
20000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 6(FREEDOM FROM DEFECTS) |
- |
500 |
|
- |
| 7 table 1(CHEMICAL COMPOSITION) |
- |
2000 |
|
- |
| 10.1(Tensile Test) |
- |
1200 |
|
- |
| 10.2(Hardness) |
- |
1200 |
|
- |
| 11(DIMENSIONS AND TOLERANCES) |
- |
500 |
|
- |
| 13(RETEST) |
- |
1500 |
|
- |
| Cl.7(Copper - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Magnesium - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Manganese - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Titanium - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Titanium+Zirconium - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Iron - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Zinc - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Tin - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Chromium - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Lead - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Copper - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Magnesium - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Silicon - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Manganese - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Titanium - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Titanium+Zirconium - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Iron - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Zinc - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Tin - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Chromium - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| Cl.7(Nickel - IS 504 and its parts or any other intrumental/chemical methods) |
- |
500 |
|
- |
| 6(Freedom from defect) |
- |
500 |
|
- |
| 10.1(Tensile strength) |
- |
1200 |
|
- |
| 12.1(Inspection and Testing) |
- |
1500 |
|
- |
| 12.2.1(Dye Penetrant Test) |
- |
560 |
|
- |
| 12.2.2(Macro and Micro-Examination) |
- |
1500 |
|
- |
| 10.1(0.2 % proof stress) |
- |
1500 |
|
- |
| 10.1(Elongation) |
- |
500 |
|
- |
| 10.2(Hardness Test) |
- |
1200 |
|
- |
| 11(Dimensions and Tolerance) |
- |
500 |
|
- |
| 6(Freedom from defect) |
- |
500 |
|
- |
| 10.1(Tensile strength) |
- |
1500 |
|
- |
| 10.1(0.2 % proof stress) |
- |
1500 |
|
- |
| 10.1(Elongation) |
- |
500 |
|
- |
| 10.2(Hardness Test) |
- |
1500 |
|
- |
| 11(DIMENSIONS AND TOLEF&WtCES) |
- |
500 |
|
- |
|
- |
-
Included w.e.f 02.06.2025
Exclusion: Cl 12.2.1 Ultrasonic test |
| 5133 |
EKO PRO ENGINEERS PVT LTD
| 8188216
| IS 14203 (2023) |
FIRE RESISTING RECORD PROTECTION CABINETS SPECIFICATION Second Revision of IS 14203 |
- |
250000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3 and 6 (Table 1)(Nominal Sizes - Height) |
- |
2000 |
|
- |
| 3 and 6 (Table 1)(Nominal Sizes - Width) |
- |
2000 |
|
- |
| 3 and 6 (Table 1)(Nominal Sizes - Depth) |
- |
2000 |
|
- |
| 3 and 6 (Table 1)(Height of Pedestal) |
- |
2000 |
|
- |
| 7(Designation) |
- |
2000 |
|
- |
| 8.1(Cabinet Construction) |
- |
2000 |
|
- |
| 8.2(Locking Mechanism) |
- |
2000 |
|
- |
| 8.3(Locks) |
- |
2000 |
|
- |
| 8.4(Handles) |
- |
2000 |
|
- |
| 9(Internal Fixtures) |
- |
2000 |
|
- |
| 10.1(Minimum overall thinckness of coating) |
- |
2000 |
|
- |
| 10.2(Cross Hatch Test) |
- |
10000 |
|
- |
| 11, Annex-B, 3.1(Fire Endurance Test) |
- |
103000 |
|
- |
| 11, Annex-B, 3.2(Fire and Impact test) |
- |
115000 |
|
- |
|
19 Sep, 2028 |
-
FR30, FR 60, FR 90, FR 120
(All type, all sizes) |
| 5134 |
Atmy Analytical Labs Private Limited (Unit-2), Greater Noida
| 8176106
| IS 4250 (2025) |
Electric Food-Mixers (Liquidizers and Grinders) and Centrifugal Juicers � Specification ( Second Revision ) |
All |
33000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl-4(General Requirements) |
- |
0 |
|
- |
| Cl-5(General Conditions for the tests) |
- |
0 |
|
- |
| Cl-6(Classification) |
- |
0 |
|
- |
| Cl-7(Marking) |
- |
0 |
|
- |
| Cl-8(Safety Requirements) |
- |
20000 |
|
- |
| Cl-9(Endurance fpr motor and base assembly) |
- |
14000 |
|
- |
| Cl-10.2("Grinding Coffee (for Machines that Have a
Dry Grinding Arrangement)") |
- |
0 |
|
Test charges included in the clause 10.5 |
| Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement)) |
- |
0 |
|
Test charges included in the clause 10.5 |
| Cl-10.4(Idli Batter) |
- |
0 |
|
Test charges included in the clause 10.5 |
| Cl-10.5(Operational Tests for Juicers) |
- |
7500 |
|
- |
| Cl-11(Temperature Withstand Test for Bowl) |
- |
4000 |
|
- |
| Cl-12.1(Test for Switches) |
- |
4000 |
|
- |
| Cl-13(Strength of Assembly) |
- |
3500 |
|
- |
| Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (ii)(Power input and current) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (iv)(Moisture resistance) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (v)(Leakage current and electric strength) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing) |
- |
0 |
|
- |
| Cl-19.11.4.1(Electrostatic discharges) |
- |
0 |
|
- |
| Cl-19.11.4.2(Radiated fields) |
- |
0 |
|
- |
| Cl-19.11.4.3(Fast transient bursts) |
- |
0 |
|
- |
| Cl-19.11.4.4(Surge immunity test) |
- |
0 |
|
- |
| Cl-19.11.4.5(Immunity to conducted discharges) |
- |
0 |
|
- |
| Cl-19.11.4.6(Class 3 Voltage dips and interruptions) |
- |
0 |
|
- |
| Cl-19.11.4.7(Harmonics) |
- |
4000 |
|
- |
| Cl-4(General Requirements) |
- |
0 |
|
- |
| Cl-5(General Conditions for the tests) |
- |
0 |
|
- |
| Cl-6(Classification) |
- |
0 |
|
- |
| Cl-7(Marking) |
- |
0 |
|
- |
| Cl-8(Safety Requirements) |
- |
0 |
|
- |
| Cl-9(Endurance fpr motor and base assembly) |
- |
0 |
|
- |
| Cl-10.2("Grinding Coffee (for Machines that Have a
Dry Grinding Arrangement)") |
- |
0 |
|
- |
| Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement)) |
- |
0 |
|
- |
| Cl-10.4(Idli Batter) |
- |
0 |
|
- |
| Cl-10.5(Operational Tests for Juicers) |
- |
0 |
|
- |
| Cl-11(Temperature Withstand Test for Bowl) |
- |
0 |
|
- |
| Cl-12.1(Test for Switches) |
- |
0 |
|
- |
| Cl-13(Strength of Assembly) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (ii)(Power input and current) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (iv)(Moisture resistance) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (v)(Leakage current and electric strength) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing) |
- |
0 |
|
- |
| Cl-4(General Requirements) |
- |
0 |
|
- |
| Cl-5(General Conditions for the tests) |
- |
0 |
|
- |
| Cl-6(Classification) |
- |
0 |
|
- |
| Cl-7(Marking) |
- |
0 |
|
- |
| Cl-8(Safety Requirements) |
- |
0 |
|
- |
| Cl-9(Endurance fpr motor and base assembly) |
- |
0 |
|
- |
| Cl-10.2("Grinding Coffee (for Machines that Have a
Dry Grinding Arrangement)") |
- |
0 |
|
- |
| Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement)) |
- |
0 |
|
- |
| Cl-10.4(Idli Batter) |
- |
0 |
|
- |
| Cl-10.5(Operational Tests for Juicers) |
- |
0 |
|
- |
| Cl-11(Temperature Withstand Test for Bowl) |
- |
0 |
|
- |
| Cl-12.1(Test for Switches) |
- |
0 |
|
- |
| Cl-13(Strength of Assembly) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (ii)(Power input and current) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (iv)(Moisture resistance) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (v)(Leakage current and electric strength) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing) |
- |
0 |
|
- |
| Cl-19.11.4.7(Harmonics) |
- |
0 |
|
- |
| Cl-4(General Requirements) |
- |
0 |
|
- |
| Cl-5(General Conditions for the tests) |
- |
0 |
|
- |
| Cl-6(Classification) |
- |
0 |
|
- |
| Cl-7(Marking) |
- |
0 |
|
- |
| Cl-8(Safety Requirements) |
- |
0 |
|
- |
| Cl-9(Endurance fpr motor and base assembly) |
- |
0 |
|
- |
| Cl-10.2("Grinding Coffee (for Machines that Have a
Dry Grinding Arrangement)") |
- |
0 |
|
- |
| Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement)) |
- |
0 |
|
- |
| Cl-10.4(Idli Batter) |
- |
0 |
|
- |
| Cl-10.5(Operational Tests for Juicers) |
- |
0 |
|
- |
| Cl-11(Temperature Withstand Test for Bowl) |
- |
0 |
|
- |
| Cl-12.1(Test for Switches) |
- |
0 |
|
- |
| Cl-13(Strength of Assembly) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (ii)(Power input and current) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (iv)(Moisture resistance) |
- |
0 |
|
- |
| Cl-14.2, Table-2 (v)(Leakage current and electric strength) |
- |
0 |
|
- |
| Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing) |
- |
0 |
|
- |
| Cl-19.11.4.7(Harmonics) |
- |
0 |
|
- |
|
08 Feb, 2027 |
-
Included w.e.f 15.07.2025
Exclusion: Cl 19.11.4.1-19.11.4.6(EMI/EMC) |
| 5135 |
Gravitas Laboratories Private Limited, Greater Noida
| 8182606
| IS 513 : Part 2 (2016) |
Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision) |
- |
12500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 7(UTM) |
- |
1200 |
|
- |
| Cl 8.5(Workmanship) |
- |
500 |
|
- |
| Cl 8.6(Workmanship) |
- |
500 |
|
- |
| Cl 9(Workmanship) |
- |
500 |
|
- |
| Cl 10(Length, Width & Thickness) |
- |
500 |
|
- |
| Cl 7(UTM) |
- |
1200 |
|
- |
| Cl 8.5(Workmanship) |
- |
500 |
|
- |
| Cl 8.6(Workmanship) |
- |
500 |
|
- |
| Cl 9(Workmanship) |
- |
500 |
|
- |
| Cl 10(Length, Width & Thickness) |
- |
500 |
|
- |
| Cl 7(UTM) |
- |
1200 |
|
- |
| Cl 8.5(Workmanship) |
- |
500 |
|
- |
| Cl 8.6(Workmanship) |
- |
500 |
|
- |
| Cl 9(Workmanship) |
- |
500 |
|
- |
| Cl 10(Length, Width & Thickness) |
- |
500 |
|
- |
| 6.0(ALUMINIUM) |
- |
500 |
|
- |
| 6.0(MICRO ALLOYS) |
- |
500 |
|
- |
| 6.0(NITROGEN) |
- |
500 |
|
- |
| 6.0(SILICON) |
- |
500 |
|
- |
| 6.0(MANGANESE) |
- |
500 |
|
- |
| 6.0(PHOSPHORUS) |
- |
500 |
|
- |
| 6.0(SULPHUR) |
- |
500 |
|
- |
| 6.0(CARBON) |
- |
500 |
|
- |
| Cl. 10(Out of square) |
- |
500 |
|
- |
| Cl. 10(Flatness) |
- |
500 |
|
- |
| Cl. 10(Camber) |
- |
500 |
|
- |
| Cl. 10(Width (04)) |
- |
500 |
|
- |
| Cl. 10(Thickness (08)) |
- |
500 |
|
- |
| Cl. 8.5.3 Table 6(Surface Roughness) |
- |
500 |
|
- |
| Cl. 7.3 Table 4A & 4B(Tensile Strain Hardening) |
- |
1500 |
|
- |
| Cl. 7.2 Table 7(Bend Test) |
- |
500 |
|
- |
| Cl 10(Length, Width & Thickness) |
- |
500 |
|
- |
| Cl 9(Workmanship) |
- |
500 |
|
- |
| Cl 8.6(Workmanship) |
- |
500 |
|
- |
| Cl 8.5(Workmanship) |
- |
500 |
|
- |
| Cl 7(UTM) |
- |
1500 |
|
- |
| Cl 7(UTM) |
- |
1500 |
|
- |
| Cl 8.5(Workmanship) |
- |
500 |
|
- |
| Cl 8.6(Workmanship) |
- |
500 |
|
- |
| Cl 9(Workmanship) |
- |
500 |
|
- |
| Cl 10(Length, Width & Thickness) |
- |
500 |
|
- |
| 7.0 & table 3(Chromium as Cr) |
- |
500 |
|
- |
| 7.0 & table 3(Nickel as Ni) |
- |
500 |
|
- |
| 7.0 & table 3(Niobium as Nb) |
- |
500 |
|
- |
| 7.0 & table 3(Vanadium as V) |
- |
500 |
|
- |
| 7.0 & table 3(Titanium as Ti) |
- |
500 |
|
- |
| 7.0 & table 3(Molybdenum as Mp) |
- |
500 |
|
- |
| 7.0 & table 3(Boron as B) |
- |
500 |
|
- |
| 7.0 & table 3(Calcium as Ca) |
- |
500 |
|
- |
| 7.2(Bend test - IS 1599) |
- |
500 |
|
- |
| 8.2(Erichson cupping test - IS 10175 for CR2, CR3, CR4 Grades from 0.5 - 2.0 mm Thickness) |
- |
500 |
|
- |
| 8.3(Rockwell Hardness test -HRB - IS:1586) |
- |
500 |
|
- |
| 7.3(Tensile strain hardening component - IS 15756) |
- |
500 |
|
- |
| 8.0(Surface Roughness) |
- |
500 |
|
- |
| 9(Freedom from defects) |
- |
500 |
|
- |
| Cl. 10(Out of square) |
- |
0 |
|
- |
| Cl. 10(Flatness) |
- |
0 |
|
- |
| Cl. 10(Camber) |
- |
0 |
|
- |
| Cl. 10(Width (04)) |
- |
0 |
|
- |
| Cl. 10(Thickness (08)) |
- |
0 |
|
- |
| Cl. 8.5.3 Table 6(Surface Roughness) |
- |
0 |
|
- |
| Cl. 7.3 Table 4A & 4B(Tensile Strain Hardening) |
- |
0 |
|
- |
| Cl. 7.2 Table 7(Bend Test) |
- |
0 |
|
- |
| Cl 10(Length, Width & Thickness) |
- |
0 |
|
- |
| Cl 9(Workmanship) |
- |
0 |
|
- |
| Cl 8.6(Workmanship) |
- |
0 |
|
- |
| Cl 8.5(Workmanship) |
- |
0 |
|
- |
| Cl 7(UTM) |
- |
0 |
|
- |
| Cl 7(UTM) |
- |
0 |
|
- |
| Cl 8.5(Workmanship) |
- |
0 |
|
- |
| Cl 8.6(Workmanship) |
- |
0 |
|
- |
| Cl 9(Workmanship) |
- |
0 |
|
- |
| Cl 10(Length, Width & Thickness) |
- |
0 |
|
- |
| 7.0 & table 3(Chromium as Cr) |
- |
0 |
|
- |
| 7.0 & table 3(Nickel as Ni) |
- |
0 |
|
- |
| 7.0 & table 3(Niobium as Nb) |
- |
0 |
|
- |
| 7.0 & table 3(Vanadium as V) |
- |
0 |
|
- |
| 7.0 & table 3(Titanium as Ti) |
- |
0 |
|
- |
| 7.0 & table 3(Molybdenum as Mp) |
- |
0 |
|
- |
| 7.0 & table 3(Boron as B) |
- |
0 |
|
- |
| 7.0 & table 3(Calcium as Ca) |
- |
0 |
|
- |
| 7.2(Bend test - IS 1599) |
- |
0 |
|
- |
| 7.3(Tensile strain hardening component - IS 15756) |
- |
0 |
|
- |
| 8.0(Surface Roughness) |
- |
0 |
|
- |
| 9(Freedom from defects) |
- |
0 |
|
- |
|
- |
-
Included w.e.f 02.06.2025 |
| 5136 |
DELHI TEST HOUSE (65) KUNDLI-2 SONIPAT
| 9138006
| IS 6162 : Part 2 (1971) |
Specification for paper covered aluminium conductors: Part 2 rectangular conductors |
-- |
10000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 10.2 a(Conductor dimensions) |
- |
2500 |
|
- |
| 10.2 b(Arrangement of Paper layers) |
- |
1500 |
|
- |
| 10.2 c(Increase in dimension) |
- |
2500 |
|
- |
| 10.2 d(Overall dimension) |
- |
3500 |
|
- |
| Cl. No. 10.2 a(Conductor dimensions) |
- |
2500 |
|
- |
| Cl. No. 10.2 b(Arrangement of Paper layers) |
- |
1500 |
|
- |
| Cl. No. 10.2 c(Increase in dimension) |
- |
2500 |
|
- |
| Cl. No. 10.2 d(Overall dimension) |
- |
3500 |
|
- |
|
31 Dec, 2026 |
-
Included w.e.f.28.07.2025 |
| 5137 |
Gravitas Laboratories Private Limited, Greater Noida
| 8182606
| IS 4454 : Part 4 (2001) |
Steel wires for mechanical springs: Part 4 stainless steel wire (Second Revision) |
All size |
9000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
500 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
500 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
500 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Suphur- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
500 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
500 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
500 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
500 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
500 |
|
- |
| 8(Freedom from defects) |
- |
500 |
|
- |
| 9(Dimensions & Tolerances) |
- |
500 |
|
- |
| 10(Mechanical properties) |
- |
2500 |
|
- |
| 10.1(Tensile test) |
- |
1200 |
|
- |
| 10.1.1, Table 4(Tensile strength) |
- |
1200 |
|
- |
| 10.1.1, Table 4(Reduction in area) |
- |
500 |
|
- |
| 10.2(Wrapping test) |
- |
1200 |
|
- |
| 10.3(Reverse torsion test) |
- |
500 |
|
- |
| 10.5(Bend test) |
- |
500 |
|
- |
| 10.6(Coiling test) |
- |
500 |
|
- |
| 11(Surface finish) |
- |
500 |
|
- |
| 10.4(Cast of the wire) |
- |
500 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
0 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
0 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
0 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Suphur- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
0 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
0 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
0 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
0 |
|
- |
| Table 1. Cl.1.1,1.2,7.1 & 7.2(Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method) |
- |
0 |
|
- |
| 8(Freedom from defects) |
- |
0 |
|
- |
| 9(Dimensions & Tolerances) |
- |
0 |
|
- |
| 10(Mechanical properties) |
- |
0 |
|
- |
| 10.1(Tensile test) |
- |
0 |
|
- |
| 10.1.1, Table 4(Tensile strength) |
- |
0 |
|
- |
| 10.1.1, Table 4(Reduction in area) |
- |
0 |
|
- |
| 10.2(Wrapping test) |
- |
0 |
|
- |
| 10.3(Reverse torsion test) |
- |
0 |
|
- |
| 10.5(Bend test) |
- |
0 |
|
- |
| 10.6(Coiling test) |
- |
0 |
|
- |
| 11(Surface finish) |
- |
0 |
|
- |
| 10.4(Cast of the wire) |
- |
0 |
|
- |
|
- |
-
Included w.e.f 02.06.2025 |
| 5138 |
DELHI TEST HOUSE (65) KUNDLI-2 SONIPAT
| 9138006
| IS 6162 : Part 1 (1971) |
Specification for paper - Covered aluminium conductors: Part 1 round conductors |
-- |
10000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.2(Diameter) |
- |
1000 |
|
- |
| 4.3(Resistance) |
- |
2500 |
|
- |
| 4.4(Tensile strength and Elongation) |
- |
1500 |
|
- |
| 6.3(Arrangement of Paper layers) |
- |
1000 |
|
- |
| 7(Overall diameter and increase in diameter) |
- |
1500 |
|
- |
| Cl. No. 4.2(Diameter) |
- |
1000 |
|
- |
| Cl. No. 4.3(Resistance) |
- |
2500 |
|
- |
| Cl. No.4.4(Tensile strength and Elongation) |
- |
1500 |
|
- |
| Cl. No. 6.3(Arrangement of Paper layers) |
- |
1000 |
|
- |
| Cl. No. 7(Overall diameter and increase in diameter) |
- |
1500 |
|
- |
| Cl. No. 10.2 a(Conductor dimensions) |
- |
1000 |
|
- |
| 4.5(IS 6162 Part-1) |
- |
1000 |
|
- |
| 4.6(IS 6162 Part-1) |
- |
200 |
|
- |
| 4.7(IS 6162 Part-1) |
- |
300 |
|
- |
|
31 Dec, 2026 |
-
Included w.e.f 20.05.2025 |
| 5139 |
EKO PRO ENGINEERS PVT LTD
| 8188216
| IS 16945 (2018) |
Fire resistance test for glass walls |
- |
440000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 11(Integrity, Insulation, Radiation) |
- |
440000 |
|
- |
|
19 Sep, 2028 |
-
All type |
| 5140 |
JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR
| 9164606
| IS 12109 (1987) |
General requirements for light duty sewing machine heads for industrial use |
- |
9000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 2.1(Construction and Function) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 2.3(Construction and Function) |
- |
999.97 |
|
For Cl. 2, 3 and 4 |
| 2.4(Construction and Function) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 2.5(Construction and Function) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 2.6(Construction and Function) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 2.7(Construction and Function) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 3.1(Finish) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 3.2(Finish) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 4.1(Sewing Mechanism) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 4.2(Sewing Mechanism) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 4.3(Sewing Mechanism) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 4.4(Sewing Mechanism) |
- |
1000 |
|
For Cl. 2, 3 and 4 |
| 5(Lubrication) |
- |
1000 |
|
For Cl.5 |
| 6.1(Accuracy Requirement) |
- |
4500 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
4500 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
45000 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
4500 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
4500 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
4500 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
4500 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Feed machanlsm- Measuring Condition -
Feed dog at the highest position above the needle plate
) |
- |
4500 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Arm shaft - Measuring Condition -
Shaft end
) |
- |
4500 |
|
For Cl. 6 |
| 6.2 Table 1(Accuracy Requirement Rotating hook shaft- Measuring Condition -
Shaft end
) |
- |
4500 |
|
For Cl. 6 |
| 7 Table 1(Durability Requirements Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
1500 |
|
For Cl. 7 |
| 7 Table 1(Durability Requirements Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
1500 |
|
For Cl. 7 |
| 7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
1500 |
|
For Cl. 7 |
| 7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
1500 |
|
For Cl. 7 |
| 7 Table 1(Durability Requirements Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
1500 |
|
For Cl. 7 |
| 7 Table 1(Durability Requirements Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
1500 |
|
For Cl. 7 |
| 7 Table 1(Durability Requirements Feed machanlsm- Measuring Condition -
Feed dog at the highest position above the needle plate
) |
- |
1500 |
|
For Cl. 7 |
| 7 Table 1(Durability Requirements Arm shaft - Measuring Condition -
Shaft end
) |
- |
1500 |
|
For Cl. 7 |
| 7 Table 1(Durability Requirements Rotating hook shaft- Measuring Condition -
Shaft end
) |
- |
1500 |
|
For Cl. 7 |
| 8 Table 2(Sewing Requirement) |
- |
1000 |
|
For Cl. 8 and 10 |
| 8 Table 3(Sewing Requirement) |
- |
1000 |
|
For Cl. 8 and 10 |
| 8 Table 2(Sewing Requirement) |
- |
1000 |
|
For Cl. 8 and 10 |
| 8 Table 2(Sewing Requirement) |
- |
1000 |
|
For Cl. 8 and 10 |
| 8 Table 2(Sewing Requirement) |
- |
1000 |
|
For Cl. 8 and 10 |
| 10(Marking) |
- |
1000 |
|
For Cl. 8 and 10 |
| 10(Marking) |
- |
1000 |
|
For Cl. 8 and 10 |
| 2.1(Construction and Function) |
- |
0 |
|
- |
| 2.3(Construction and Function) |
- |
0 |
|
- |
| 2.4(Construction and Function) |
- |
0 |
|
- |
| 2.5(Construction and Function) |
- |
0 |
|
- |
| 2.6(Construction and Function) |
- |
0 |
|
- |
| 2.7(Construction and Function) |
- |
0 |
|
- |
| 3.1(Finish) |
- |
0 |
|
- |
| 3.2(Finish) |
- |
0 |
|
- |
| 4.1(Sewing Mechanism) |
- |
0 |
|
- |
| 4.2(Sewing Mechanism) |
- |
0 |
|
- |
| 4.3(Sewing Mechanism) |
- |
0 |
|
- |
| 4.4(Sewing Mechanism) |
- |
0 |
|
- |
| 5(Lubrication) |
- |
0 |
|
- |
| 6.1(Accuracy Requirement) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Feed machanlsm- Measuring Condition -
Feed dog at the highest position above the needle plate
) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Arm shaft - Measuring Condition -
Shaft end
) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook shaft- Measuring Condition -
Shaft end
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Feed machanlsm- Measuring Condition -
Feed dog at the highest position above the needle plate
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Arm shaft - Measuring Condition -
Shaft end
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Rotating hook shaft- Measuring Condition -
Shaft end
) |
- |
0 |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
0 |
|
- |
| 8 Table 3(Sewing Requirement) |
- |
0 |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
0 |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
0 |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
0 |
|
- |
| 10(Marking) |
- |
0 |
|
- |
| 10(Marking) |
- |
0 |
|
- |
| As per Clause 9(Accessories) |
- |
0 |
|
- |
| As per Clause 11(Packing) |
- |
0 |
|
- |
| Clause 12(Sampling) |
- |
0 |
|
- |
| Clause 2.2(Construction and function - Component) |
- |
0 |
|
- |
| 2.1(Construction and Function) |
- |
0 |
|
- |
| 2.3(Construction and Function) |
- |
0 |
|
- |
| 2.4(Construction and Function) |
- |
0 |
|
- |
| 2.5(Construction and Function) |
- |
0 |
|
- |
| 2.6(Construction and Function) |
- |
0 |
|
- |
| 2.7(Construction and Function) |
- |
0 |
|
- |
| 3.1(Finish) |
- |
0 |
|
- |
| 3.2(Finish) |
- |
0 |
|
- |
| 4.1(Sewing Mechanism) |
- |
0 |
|
- |
| 4.2(Sewing Mechanism) |
- |
0 |
|
- |
| 4.3(Sewing Mechanism) |
- |
0 |
|
- |
| 4.4(Sewing Mechanism) |
- |
0 |
|
- |
| 5(Lubrication) |
- |
0 |
|
- |
| 6.1(Accuracy Requirement) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Feed machanlsm- Measuring Condition -
Feed dog at the highest position above the needle plate
) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Arm shaft - Measuring Condition -
Shaft end
) |
- |
0 |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook shaft- Measuring Condition -
Shaft end
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Feed machanlsm- Measuring Condition -
Feed dog at the highest position above the needle plate
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Arm shaft - Measuring Condition -
Shaft end
) |
- |
0 |
|
- |
| 7 Table 1(Durability Requirements Rotating hook shaft- Measuring Condition -
Shaft end
) |
- |
0 |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
0 |
|
- |
| 8 Table 3(Sewing Requirement) |
- |
0 |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
0 |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
0 |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
0 |
|
- |
| 10(Marking) |
- |
0 |
|
- |
| 10(Marking) |
- |
0 |
|
- |
| As per Clause 9(Accessories) |
- |
0 |
|
- |
| As per Clause 11(Packing) |
- |
0 |
|
- |
| Clause 12(Sampling) |
- |
0 |
|
- |
| Clause 2.2(Construction and function - Component) |
- |
0 |
|
- |
| 2.1(Construction and Function) |
- |
- |
|
- |
| 2.3(Construction and Function) |
- |
- |
|
- |
| 2.4(Construction and Function) |
- |
- |
|
- |
| 2.5(Construction and Function) |
- |
- |
|
- |
| 2.6(Construction and Function) |
- |
- |
|
- |
| 2.7(Construction and Function) |
- |
- |
|
- |
| 3.1(Finish) |
- |
- |
|
- |
| 3.2(Finish) |
- |
- |
|
- |
| 4.1(Sewing Mechanism) |
- |
- |
|
- |
| 4.2(Sewing Mechanism) |
- |
- |
|
- |
| 4.3(Sewing Mechanism) |
- |
- |
|
- |
| 4.4(Sewing Mechanism) |
- |
- |
|
- |
| 5(Lubrication) |
- |
- |
|
- |
| 6.1(Accuracy Requirement) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Feed machanlsm- Measuring Condition -
Feed dog at the highest position above the needle plate
) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Arm shaft - Measuring Condition -
Shaft end
) |
- |
- |
|
- |
| 6.2 Table 1(Accuracy Requirement Rotating hook shaft- Measuring Condition -
Shaft end
) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Needle Bar - Measuring Condition -
Needle bar at lowermost position) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Thread takeup lever - Measuring Condition -
Thread take up lever at top and
intermediate position of motion) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Rotating hook- Measuring Condition -
With bobbin-case removed, play of
rotating hook bobbin case holder
) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Feed machanlsm- Measuring Condition -
Feed dog at the highest position above the needle plate
) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Arm shaft - Measuring Condition -
Shaft end
) |
- |
- |
|
- |
| 7 Table 1(Durability Requirements Rotating hook shaft- Measuring Condition -
Shaft end
) |
- |
- |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
- |
|
- |
| 8 Table 3(Sewing Requirement) |
- |
- |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
- |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
- |
|
- |
| 8 Table 2(Sewing Requirement) |
- |
- |
|
- |
| 10(Marking) |
- |
- |
|
- |
| 10(Marking) |
- |
- |
|
- |
| As per Clause 9(Accessories) |
- |
- |
|
- |
| As per Clause 11(Packing) |
- |
- |
|
- |
| Clause 12(Sampling) |
- |
- |
|
- |
| Clause 2.2(Construction and function - Component) |
- |
- |
|
- |
|
- |
-
Included w.e.f 24.06.2025 |
| 5141 |
ALPHA TEST HOUSE SERVICES LLP (Unit-1), MOHALI
| 9184906
| IS 2202 : Part 1 (2023) |
WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Seventh Revision |
ALL |
28000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 9.1(Workmanship & Finish) |
- |
28000 |
|
- |
| 9.2(Workmanship & Finish) |
- |
28000 |
|
- |
| 9.3(Workmanship & Finish) |
- |
28000 |
|
- |
| 11.1(Dimensions - Height) |
- |
28000 |
|
- |
| 11.1(Dimensions - Width) |
- |
28000 |
|
- |
| 11.1(Dimensions - Thickness) |
- |
28000 |
|
- |
| 11.1(Dimensions - Variation in thickness) |
- |
28000 |
|
- |
| 11.1(Dimensions - Squareness) |
- |
28000 |
|
- |
| 11.12(End immersion test) |
- |
28000 |
|
- |
| 11.13(Knife Test) |
- |
28000 |
|
- |
| 11.14(Glue Adhesion Test) |
- |
28000 |
|
- |
| 4(GRADE) |
- |
28000 |
|
- |
| 4(TYPE) |
- |
28000 |
|
- |
| 5(SIZES) |
- |
28000 |
|
- |
| 7.1.1(CONSTRUCTION-Blockboard Core) |
- |
28000 |
|
- |
| 7.1.1(CONSTRUCTION-Blockboard Core) |
- |
28000 |
|
- |
| 7.1.2(CONSTRUCTION-Blockboard Core) |
- |
28000 |
|
- |
| 7.3.2(CONSTRUCTION-Stiles and Rails) |
- |
28000 |
|
- |
| 7.3.2(a)(CONSTRUCTION-Stiles and Rails-Joints) |
- |
28000 |
|
- |
| 7.3.2(b)(CONSTRUCTION-Stiles and Rails-Joints) |
- |
28000 |
|
- |
| 7.3.2(c)(CONSTRUCTION-Stiles and Rails-Joints) |
- |
28000 |
|
- |
| 7.3.3(CONSTRUCTION-Stiles and Rails) |
- |
28000 |
|
- |
| 9.1(WORKMANSHIP AND FINISH) |
- |
28000 |
|
- |
| 9.2(WORKMANSHIP AND FINISH) |
- |
28000 |
|
- |
| 9.3(WORKMANSHIP AND FINISH) |
- |
28000 |
|
- |
| 11.1(Dimensions and Squareness Test) |
- |
28000 |
|
- |
| 11.1(Dimensions and Squareness Test) |
- |
28000 |
|
- |
| 11.1(Dimensions and Squareness Test) |
- |
28000 |
|
- |
| 11.1(Dimensions and Squareness Test) |
- |
28000 |
|
- |
| 11.1(Dimensions and Squareness Test) |
- |
28000 |
|
- |
| 11.2(General Flatness Test) |
- |
28000 |
|
- |
| 11.2(General Flatness Test) |
- |
28000 |
|
- |
| 11.2(General Flatness Test) |
- |
28000 |
|
- |
| 11.3(Local Planeness Test) |
- |
28000 |
|
- |
| 11.4(Impact Indentation Test) |
- |
28000 |
|
- |
| 11.4(Impact Indentation Test) |
- |
28000 |
|
- |
| 11.5(Flexure Test) |
- |
28000 |
|
- |
| 11.5(Flexure Test) |
- |
28000 |
|
- |
| 11.6(Edge Loading Test) |
- |
28000 |
|
- |
| 11.6(Edge Loading Test) |
- |
28000 |
|
- |
| 11.6(Edge Loading Test) |
- |
28000 |
|
- |
| 11.6(Edge Loading Test) |
- |
28000 |
|
- |
| 11.7.1(Shock Resistance Test) |
- |
28000 |
|
- |
| 11.7.2(Shock Resistance Test) |
- |
28000 |
|
- |
| 11.8(Buckling Test) |
- |
28000 |
|
- |
| 11.8(Buckling Test) |
- |
28000 |
|
- |
| 11.8(Buckling Test) |
- |
28000 |
|
- |
| 11.9.2(Slamming Test) |
- |
28000 |
|
- |
| 11.9.3(Slamming Test) |
- |
28000 |
|
- |
| 11.10(Misuse Test) |
- |
28000 |
|
- |
| 11.11(Varying Humidity Test) |
- |
28000 |
|
- |
| 11.11(Varying Humidity Test) |
- |
28000 |
|
- |
| 11.12(End Immersion Test) |
- |
28000 |
|
- |
| 11.13(Knife Test) |
- |
28000 |
|
- |
| 11.14(Glue Adhesion Test) |
- |
28000 |
|
- |
| 11.15(Screw Withdrawal Resistance Test) |
- |
28000 |
|
- |
| 11.15(Screw Withdrawal Resistance Test) |
- |
28000 |
|
- |
| Clause 4.2(grades specified) |
- |
28000 |
|
- |
| Clause 5(SIZES) |
- |
28000 |
|
- |
| Clause 6.1.1(species of timber) |
- |
28000 |
|
- |
| Clause 6.1.2(list of species) |
- |
28000 |
|
- |
| Clause 6.1.3(moisture content) |
- |
28000 |
|
- |
| Clause 6.2.1(Plywood) |
- |
28000 |
|
- |
| Clause 6.2.2(Decorative plywood) |
- |
28000 |
|
- |
| Clause 6.3(Cross-Bands) |
- |
28000 |
|
- |
| Clause 6.4.1(Commercial Face
Veneers) |
- |
28000 |
|
- |
| Clause 6.4.2(Decorative Face
Veneers) |
- |
28000 |
|
- |
| Clause 6.6.1(Adhesives) |
- |
28000 |
|
- |
| Clause 6.7(Particle Board) |
- |
28000 |
|
- |
| Clause 6.8(Medium density
fibre board) |
- |
28000 |
|
- |
| Clause 6.9(Alternative Materials) |
- |
28000 |
|
- |
| Clause 7.1(Blockboard Core) |
- |
28000 |
|
- |
| Clause 7.2(Particle Board or
Medium Density Fibre) |
- |
28000 |
|
- |
| Clause 7.3(Stiles and Rails) |
- |
28000 |
|
- |
| Clause 7.4(Levelling) |
- |
28000 |
|
- |
| Clause 7.5(Face Panel) |
- |
28000 |
|
- |
| Clause 7.6(Lipping) |
- |
28000 |
|
- |
| Clause 7.7(Rebating) |
- |
28000 |
|
- |
| Clause 7.8(Opening for Glazing) |
- |
28000 |
|
- |
| Clause 7.9(Venetian) |
- |
28000 |
|
- |
| Clause 8.1(Locks) |
- |
28000 |
|
- |
| Clause 9(WORKMANSHIP AND
FINISH) |
- |
28000 |
|
- |
| Clause 10.1(Classification of Tests) |
- |
28000 |
|
- |
| Clause 11.1(Dimensions and
Squareness Test) |
- |
28000 |
|
- |
| Clause 11.2(General Flatness Test) |
- |
28000 |
|
- |
| Clause 11.3(Local Planeness Test) |
- |
28000 |
|
- |
| Clause 11.4(Impact Indentation Test) |
- |
28000 |
|
- |
| Clause 11.5(Flexure Test) |
- |
28000 |
|
- |
| Clause 11.6(Edge Loading Test) |
- |
28000 |
|
- |
| Clause 11.7(Shock Resistance Test) |
- |
28000 |
|
- |
| Clause 11.8(Buckling Resistance Test) |
- |
28000 |
|
- |
| Clause 11.9(Slamming Test) |
- |
28000 |
|
- |
| Clause 11.10(Misuse Test) |
- |
28000 |
|
- |
| Clause 11.11(Varying Humidity Test) |
- |
28000 |
|
- |
| Clause 11.12(End Immersion Test) |
- |
28000 |
|
- |
| Clause 11.13(Knife Test) |
- |
28000 |
|
- |
| Clause 11.14(Glue Adhesion Test) |
- |
28000 |
|
- |
| Clause 11.15(Screw Withdrawal
Resistance Test) |
- |
28000 |
|
- |
| Clause 12(SAMPLING AND CRITERIA
FOR CONFORMITY) |
- |
28000 |
|
- |
| Clause 13(ADDITIONAL REQUIREMENTS
FOR ECO MARK) |
- |
28000 |
|
- |
| Clause 14(Marking) |
- |
28000 |
|
- |
| 4(Grade, Type and Construction) |
- |
28000 |
|
- |
| 5(Sizes and Thickness) |
- |
28000 |
|
- |
| 6.1(Timber) |
- |
28000 |
|
- |
| 6.2(Plywood for flush door shutter) |
- |
28000 |
|
- |
| 6.3(Cross-Bands ) |
- |
28000 |
|
- |
| 6.4.1(Commercial Face Veneers) |
- |
28000 |
|
- |
| 6.4.2(Decorative face veneers) |
- |
28000 |
|
- |
| 6.6(Adhesives) |
- |
28000 |
|
- |
| 6.7(Particle Board) |
- |
28000 |
|
- |
| 6.8(Medium Density Fibre) |
- |
28000 |
|
- |
| 6.9(Alternative Materials) |
- |
28000 |
|
- |
| 7(Construction) |
- |
28000 |
|
- |
| 8.1(Locks) |
- |
28000 |
|
- |
| 8.2(Other Fittings) |
- |
28000 |
|
- |
| 9(Workmanship and Finish) |
- |
28000 |
|
- |
| 10(Tests) |
- |
28000 |
|
- |
| 11.1(Dimensions and Squareness Test) |
- |
28000 |
|
- |
| 11.2(General Flatness Test) |
- |
28000 |
|
- |
| 11.3(Local Planeness Test) |
- |
28000 |
|
- |
| 11.4(Impact Indentation Test) |
- |
28000 |
|
- |
| 11.5(Flexure Test) |
- |
28000 |
|
- |
| 11.6(Edge Loading Test) |
- |
28000 |
|
- |
| 11.7(Shock Resistance Test) |
- |
28000 |
|
- |
| 11.8(Buckling Resistance Test) |
- |
28000 |
|
- |
| 11.9(Slamming Test) |
- |
28000 |
|
- |
| 11.1(Misuse Test) |
- |
28000 |
|
- |
| 11.11(Varying Humidity Test) |
- |
28000 |
|
- |
| 11.12(End Immersion Test) |
- |
28000 |
|
- |
| 11.13(Knife Test) |
- |
28000 |
|
- |
| 11.14(Glue Adhesion Test) |
- |
28000 |
|
- |
| 11.15(Screw Withdrawal Resistance Test) |
- |
28000 |
|
- |
| 14(Marking ) |
- |
28000 |
|
- |
| Cl-13(ADDITIONAL REQUIREMENTS FOR ECO
MARK) |
- |
28000 |
|
- |
|
25 Apr, 2028 |
-
Included w.e.f 19.05.2025 |
| 5142 |
Sleen India Biz venture Private Limited, Agra
| 9139736
| IS 17374 (2020) |
Geosynthetics – Reinforced HDPE membrane for effluents and chemical resistance lining – Specification |
All Type |
220000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Clause No. 3.1(Reinforced HDPE Membrane) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (i)(Thickness (mm)) |
- |
500 |
|
- |
| Clause No. 5.3, Table No. 1, (ii)(Mass (g/m2)) |
- |
500 |
|
- |
| Clause No. 5.3, Table No. 1, (iii)(Dimensions (length and width)) |
- |
500 |
|
- |
| Clause No. 3.1, Table No. 1, (iv)(Carbon black content, percent) |
- |
2000 |
|
- |
| Clause No. 3.1, Table No. 1, (v)(Carbon black dispersion) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (vi)(Breaking load on 20 cm × 10 cm strip before UV exposure, N) |
- |
5000 |
|
- |
| Clause No. 5.3, Table No. 1, (vii)(Strain at maximum load, percent) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (viii)(Retention of breaking load on 20 cm × 10 cm strip after UV exposure of 144 h) |
- |
20000 |
|
- |
| Clause No. 5.3, Table No. 1, (ix)(Impact failure load, at 1524 mm drop, Min gram force at 50 percent failure) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (x)(Tear resistance, N) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (x)(Tear resistance, N) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (xi)(Puncture resistance, N) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (xii)(Bursting strength (Ball burst), N/cm2) |
- |
1000 |
|
- |
| Clause No. 5.3, Table No. 1, (xiii)(Seam strength before UV exposure, N/mm) |
- |
1000 |
|
- |
| Clause No. 5.3, Table No. 1, (xiv)(Seam strength after UV exposure of 144 h, N/mm) |
- |
20000 |
|
- |
| Clause No. 5.3, Table No. 1, (xv)(Hydrostatic resistance before UV exposure, kg/cm2) |
- |
1000 |
|
- |
| Clause No. 5.3, Table No. 1, (xvi)(Hydrostatic resistance after UV exposure of 144 h, kg/cm2) |
- |
5000 |
|
- |
| Clause No. 5.3, Table No. 1, (xvii)(Low temperature crack resistance at minus 30 °C ± 1°C) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (xviii)(Oxidative induction time (OIT), minutes, (a) Standard OIT or (b) High Pressure OIT) |
- |
10000 |
|
- |
| Clause No. 5.3, Table No. 1, (xix)(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days, percent, (a) Standard OIT or (b) High Pressure OIT) |
- |
60000 |
|
- |
| Clause No. 5.3, Table No. 1, (xx)(Stress crack resistance, h) |
- |
2000 |
|
- |
| Clause No. 5.3, Table No. 1, (xxi)(Abrasion resistance) |
- |
1000 |
|
- |
| Clause No. 5.3, Table No. 1, (xxii)(Ash content, percent) |
- |
1000 |
|
- |
| Clause No. 5.4, Table No. 2, (i)(Change in weight, percent) |
- |
50000 |
|
- |
| Clause No. 5.4, Table No. 2, (ii)(Change in volume, percent) |
- |
2000 |
|
- |
| Clause No. 5.4, Table No. 2, (iii)(Visual observations) |
- |
500 |
|
- |
| Clause No. 5.4, Table No. 2, (iv)(Change in tensile strength, percent) |
- |
1000 |
|
- |
| Clause No. 5.4, Table No. 2, (v)(Change in elongation, percent) |
- |
1000 |
|
- |
| Clause No. 5.4, Table No. 2, (vi)(Change in 2 percent secant modulus, percent) |
- |
1000 |
|
- |
| Clause No. 5.4, Table No. 2, (vii)(Change in seam strength, percent) |
- |
2000 |
|
- |
| 3.1(MATERIAL AND MANUFACTURE - -HDPE membrane -UV stablised or carbon black stablised LDPE or LLDPE shall contain minimum 2.5 percent of carbon black) |
- |
2000 |
|
- |
| 3.2(MATERIAL AND MANUFACTURE - A suitable multi-layer membrane with adequate number of layers shall be produced using a combination of HDPE fabric and layers of coating film) |
- |
1000 |
|
- |
| 3.3- Table 1 - i)(Thickness (mm)) |
- |
500 |
|
- |
| 3.3- Table 1 - ii)(Mass (g/m2)) |
- |
500 |
|
- |
| 3.3- Table 1 - iii)(Dimensions (length and width)) |
- |
500 |
|
- |
| 3.3- Table 1 - iv)(Carbon black content, percent) |
- |
1000 |
|
- |
| 3.3- Table 1 - v)(Carbon black dispersion) |
- |
1000 |
|
- |
| 3.3- Table 1 - vi)("Breaking load on 20 cm × 10 cm strip before UV exposure, N, Min
a) Warp way b) Weft way") |
- |
1000 |
|
- |
| 3.3- Table 1 - vii)(Strain at maximum load) |
- |
2000 |
|
- |
| 3.3- Table 1 - viii)(Retention of breaking load on 20 cm × 10 cm strip after UV exposure of 144 h a) Warp way b) Weft way) |
- |
20000 |
|
- |
| 3.3- Table 1 - ix)(Impact failure load, at 1524 mm drop, Min gram force at 50 percent failure) |
- |
2000 |
|
- |
| 3.3- Table 1 - x)(Tear resistance, N) |
- |
2000 |
|
- |
| 3.3- Table 1 - xi)(Puncture resistance, N) |
- |
2000 |
|
- |
| 3.3- Table 1 - xii)(Bursting strength (Ball burst), N/cm2) |
- |
1000 |
|
- |
| 3.3- Table 1 - xiii)(Seam strength before UV exposure, N/ mm) |
- |
1000 |
|
- |
| 3.3- Table 1 - xiv)(Seam strength after UV exposure of 144 h, N/mm) |
- |
20000 |
|
- |
| 3.3- Table 1 - xv)(Hydrostatic resistance before UV exposure, kg/cm2 ,) |
- |
1000 |
|
- |
| 3.3- Table 1 - xvi)(Hydrostatic resistance after UV exposure of 144 h, kg/cm2) |
- |
10000 |
|
- |
| 3.3- Table 1 - xvii)("Low temperature crack resistance at
minus 30 °C ± 1°C") |
- |
2000 |
|
- |
| 3.3- Table 1 - xviii)(Oxidative induction time (OIT), minutes a) Standard OIT or b) High pressure OIT) |
- |
10000 |
|
- |
| 3.3- Table 1 - xix)(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days, percent a) Standard OIT or b) High pressure OIT) |
- |
60000 |
|
- |
| 3.3- Table 1 - xx)(Stress crack resistance) |
- |
2000 |
|
- |
| 3.3- Table 1 - xxi)(Abrasion resistance) |
- |
1000 |
|
- |
| 3.3- Table 1 - xxii)(Ash content, Max) |
- |
1000 |
|
- |
| 4(TYPES OF GEOGRIDS - a) Type I b) Type II c) Type III d) Type IV e) Type V f) Type VI) |
- |
500 |
|
- |
| 5.1(REQUIREMENTS - Workmanship) |
- |
500 |
|
- |
| 5.2(REQUIREMENTS - Joints/Seams) |
- |
500 |
|
- |
| 5.4-Table 2- i)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in weight) |
- |
50000 |
|
- |
| 5.4-Table 2- ii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in volume) |
- |
2000 |
|
- |
| 5.4-Table 2- iii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Visual observations) |
- |
500 |
|
- |
| 5.4-Table 2- iv)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in tensile strength) |
- |
1000 |
|
- |
| 5.4-Table 2- v)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in elongation) |
- |
1000 |
|
- |
| 5.4-Table 2- vi)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in 2 percent secant modulus) |
- |
1000 |
|
- |
| 5.4-Table 2- vii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in seam strength) |
- |
2000 |
|
- |
| 6(PACKING AND MARKING) |
- |
200 |
|
- |
| Clause No. 3.1(Reinforced HDPE Membrane) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (i)(Thickness (mm)) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (ii)(Mass (g/m2)) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (iii)(Dimensions (length and width)) |
- |
0 |
|
- |
| Clause No. 3.1, Table No. 1, (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 3.1, Table No. 1, (v)(Carbon black dispersion) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (vi)(Breaking load on 20 cm × 10 cm strip before UV exposure, N) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (vii)(Strain at maximum load, percent) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (viii)(Retention of breaking load on 20 cm × 10 cm strip after UV exposure of 144 h) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (ix)(Impact failure load, at 1524 mm drop, Min gram force at 50 percent failure) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (x)(Tear resistance, N) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (x)(Tear resistance, N) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xi)(Puncture resistance, N) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xii)(Bursting strength (Ball burst), N/cm2) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xiii)(Seam strength before UV exposure, N/mm) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xiv)(Seam strength after UV exposure of 144 h, N/mm) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xv)(Hydrostatic resistance before UV exposure, kg/cm2) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xvi)(Hydrostatic resistance after UV exposure of 144 h, kg/cm2) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xvii)(Low temperature crack resistance at minus 30 °C ± 1°C) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xviii)(Oxidative induction time (OIT), minutes, (a) Standard OIT or (b) High Pressure OIT) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xix)(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days, percent, (a) Standard OIT or (b) High Pressure OIT) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xx)(Stress crack resistance, h) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xxi)(Abrasion resistance) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xxii)(Ash content, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (i)(Change in weight, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (ii)(Change in volume, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (iii)(Visual observations) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (iv)(Change in tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (v)(Change in elongation, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (vi)(Change in 2 percent secant modulus, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (vii)(Change in seam strength, percent) |
- |
0 |
|
- |
| 3.1(MATERIAL AND MANUFACTURE - -HDPE membrane -UV stablised or carbon black stablised LDPE or LLDPE shall contain minimum 2.5 percent of carbon black) |
- |
0 |
|
- |
| 3.2(MATERIAL AND MANUFACTURE - A suitable multi-layer membrane with adequate number of layers shall be produced using a combination of HDPE fabric and layers of coating film) |
- |
0 |
|
- |
| 3.3- Table 1 - i)(Thickness (mm)) |
- |
0 |
|
- |
| 3.3- Table 1 - ii)(Mass (g/m2)) |
- |
0 |
|
- |
| 3.3- Table 1 - iii)(Dimensions (length and width)) |
- |
0 |
|
- |
| 3.3- Table 1 - iv)(Carbon black content, percent) |
- |
0 |
|
- |
| 3.3- Table 1 - v)(Carbon black dispersion) |
- |
0 |
|
- |
| 3.3- Table 1 - vi)("Breaking load on 20 cm × 10 cm strip before UV exposure, N, Min
a) Warp way b) Weft way") |
- |
0 |
|
- |
| 3.3- Table 1 - vii)(Strain at maximum load) |
- |
0 |
|
- |
| 3.3- Table 1 - viii)(Retention of breaking load on 20 cm × 10 cm strip after UV exposure of 144 h a) Warp way b) Weft way) |
- |
0 |
|
- |
| 3.3- Table 1 - ix)(Impact failure load, at 1524 mm drop, Min gram force at 50 percent failure) |
- |
0 |
|
- |
| 3.3- Table 1 - x)(Tear resistance, N) |
- |
0 |
|
- |
| 3.3- Table 1 - xi)(Puncture resistance, N) |
- |
0 |
|
- |
| 3.3- Table 1 - xii)(Bursting strength (Ball burst), N/cm2) |
- |
0 |
|
- |
| 3.3- Table 1 - xiii)(Seam strength before UV exposure, N/ mm) |
- |
0 |
|
- |
| 3.3- Table 1 - xiv)(Seam strength after UV exposure of 144 h, N/mm) |
- |
0 |
|
- |
| 3.3- Table 1 - xv)(Hydrostatic resistance before UV exposure, kg/cm2 ,) |
- |
0 |
|
- |
| 3.3- Table 1 - xvi)(Hydrostatic resistance after UV exposure of 144 h, kg/cm2) |
- |
0 |
|
- |
| 3.3- Table 1 - xvii)("Low temperature crack resistance at
minus 30 °C ± 1°C") |
- |
0 |
|
- |
| 3.3- Table 1 - xviii)(Oxidative induction time (OIT), minutes a) Standard OIT or b) High pressure OIT) |
- |
0 |
|
- |
| 3.3- Table 1 - xix)(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days, percent a) Standard OIT or b) High pressure OIT) |
- |
0 |
|
- |
| 3.3- Table 1 - xx)(Stress crack resistance) |
- |
0 |
|
- |
| 3.3- Table 1 - xxi)(Abrasion resistance) |
- |
0 |
|
- |
| 3.3- Table 1 - xxii)(Ash content, Max) |
- |
0 |
|
- |
| 4(TYPES OF GEOGRIDS - a) Type I b) Type II c) Type III d) Type IV e) Type V f) Type VI) |
- |
0 |
|
- |
| 5.1(REQUIREMENTS - Workmanship) |
- |
0 |
|
- |
| 5.2(REQUIREMENTS - Joints/Seams) |
- |
0 |
|
- |
| 5.4-Table 2- i)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in weight) |
- |
0 |
|
- |
| 5.4-Table 2- ii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in volume) |
- |
0 |
|
- |
| 5.4-Table 2- iii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Visual observations) |
- |
0 |
|
- |
| 5.4-Table 2- iv)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in tensile strength) |
- |
0 |
|
- |
| 5.4-Table 2- v)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in elongation) |
- |
0 |
|
- |
| 5.4-Table 2- vi)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in 2 percent secant modulus) |
- |
0 |
|
- |
| 5.4-Table 2- vii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in seam strength) |
- |
0 |
|
- |
| 6(PACKING AND MARKING) |
- |
0 |
|
- |
| Clause No. 3.1(Reinforced HDPE Membrane) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (i)(Thickness (mm)) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (ii)(Mass (g/m2)) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (iii)(Dimensions (length and width)) |
- |
0 |
|
- |
| Clause No. 3.1, Table No. 1, (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 3.1, Table No. 1, (v)(Carbon black dispersion) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (vi)(Breaking load on 20 cm × 10 cm strip before UV exposure, N) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (vii)(Strain at maximum load, percent) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (viii)(Retention of breaking load on 20 cm × 10 cm strip after UV exposure of 144 h) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (ix)(Impact failure load, at 1524 mm drop, Min gram force at 50 percent failure) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (x)(Tear resistance, N) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (x)(Tear resistance, N) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xi)(Puncture resistance, N) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xii)(Bursting strength (Ball burst), N/cm2) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xiii)(Seam strength before UV exposure, N/mm) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xiv)(Seam strength after UV exposure of 144 h, N/mm) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xv)(Hydrostatic resistance before UV exposure, kg/cm2) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xvi)(Hydrostatic resistance after UV exposure of 144 h, kg/cm2) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xvii)(Low temperature crack resistance at minus 30 °C ± 1°C) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xviii)(Oxidative induction time (OIT), minutes, (a) Standard OIT or (b) High Pressure OIT) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xix)(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days, percent, (a) Standard OIT or (b) High Pressure OIT) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xx)(Stress crack resistance, h) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xxi)(Abrasion resistance) |
- |
0 |
|
- |
| Clause No. 5.3, Table No. 1, (xxii)(Ash content, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (i)(Change in weight, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (ii)(Change in volume, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (iii)(Visual observations) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (iv)(Change in tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (v)(Change in elongation, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (vi)(Change in 2 percent secant modulus, percent) |
- |
0 |
|
- |
| Clause No. 5.4, Table No. 2, (vii)(Change in seam strength, percent) |
- |
0 |
|
- |
| 3.1(MATERIAL AND MANUFACTURE - -HDPE membrane -UV stablised or carbon black stablised LDPE or LLDPE shall contain minimum 2.5 percent of carbon black) |
- |
0 |
|
- |
| 3.2(MATERIAL AND MANUFACTURE - A suitable multi-layer membrane with adequate number of layers shall be produced using a combination of HDPE fabric and layers of coating film) |
- |
0 |
|
- |
| 3.3- Table 1 - i)(Thickness (mm)) |
- |
0 |
|
- |
| 3.3- Table 1 - ii)(Mass (g/m2)) |
- |
0 |
|
- |
| 3.3- Table 1 - iii)(Dimensions (length and width)) |
- |
0 |
|
- |
| 3.3- Table 1 - iv)(Carbon black content, percent) |
- |
0 |
|
- |
| 3.3- Table 1 - v)(Carbon black dispersion) |
- |
0 |
|
- |
| 3.3- Table 1 - vi)("Breaking load on 20 cm × 10 cm strip before UV exposure, N, Min
a) Warp way b) Weft way") |
- |
0 |
|
- |
| 3.3- Table 1 - vii)(Strain at maximum load) |
- |
0 |
|
- |
| 3.3- Table 1 - viii)(Retention of breaking load on 20 cm × 10 cm strip after UV exposure of 144 h a) Warp way b) Weft way) |
- |
0 |
|
- |
| 3.3- Table 1 - ix)(Impact failure load, at 1524 mm drop, Min gram force at 50 percent failure) |
- |
0 |
|
- |
| 3.3- Table 1 - x)(Tear resistance, N) |
- |
0 |
|
- |
| 3.3- Table 1 - xi)(Puncture resistance, N) |
- |
0 |
|
- |
| 3.3- Table 1 - xii)(Bursting strength (Ball burst), N/cm2) |
- |
0 |
|
- |
| 3.3- Table 1 - xiii)(Seam strength before UV exposure, N/ mm) |
- |
0 |
|
- |
| 3.3- Table 1 - xiv)(Seam strength after UV exposure of 144 h, N/mm) |
- |
0 |
|
- |
| 3.3- Table 1 - xv)(Hydrostatic resistance before UV exposure, kg/cm2 ,) |
- |
0 |
|
- |
| 3.3- Table 1 - xvi)(Hydrostatic resistance after UV exposure of 144 h, kg/cm2) |
- |
0 |
|
- |
| 3.3- Table 1 - xvii)("Low temperature crack resistance at
minus 30 °C ± 1°C") |
- |
0 |
|
- |
| 3.3- Table 1 - xviii)(Oxidative induction time (OIT), minutes a) Standard OIT or b) High pressure OIT) |
- |
0 |
|
- |
| 3.3- Table 1 - xix)(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days, percent a) Standard OIT or b) High pressure OIT) |
- |
0 |
|
- |
| 3.3- Table 1 - xx)(Stress crack resistance) |
- |
0 |
|
- |
| 3.3- Table 1 - xxi)(Abrasion resistance) |
- |
0 |
|
- |
| 3.3- Table 1 - xxii)(Ash content, Max) |
- |
0 |
|
- |
| 4(TYPES OF GEOGRIDS - a) Type I b) Type II c) Type III d) Type IV e) Type V f) Type VI) |
- |
0 |
|
- |
| 5.1(REQUIREMENTS - Workmanship) |
- |
0 |
|
- |
| 5.2(REQUIREMENTS - Joints/Seams) |
- |
0 |
|
- |
| 5.4-Table 2- i)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in weight) |
- |
0 |
|
- |
| 5.4-Table 2- ii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in volume) |
- |
0 |
|
- |
| 5.4-Table 2- iii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Visual observations) |
- |
0 |
|
- |
| 5.4-Table 2- iv)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in tensile strength) |
- |
0 |
|
- |
| 5.4-Table 2- v)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in elongation) |
- |
0 |
|
- |
| 5.4-Table 2- vi)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in 2 percent secant modulus) |
- |
0 |
|
- |
| 5.4-Table 2- vii)(Requirements of Reinforced HDPE Membranes after Treating Against Chemicals - Change in seam strength) |
- |
0 |
|
- |
| 6(PACKING AND MARKING) |
- |
0 |
|
- |
|
- |
-
Included w.e.f 02.06.2025 |
| 5143 |
DELHI TEST HOUSE (65) KUNDLI-2 SONIPAT
| 9138006
| IS 17046 (2018) |
Fibre Optic Cable for Cable TV Application |
-- |
125000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3.1(Design and construction of aerial metal free optical fibre cable) |
- |
0 |
|
- |
| 3.2(Fibre used in the cable) |
- |
0 |
|
- |
| 3.3(Self-supporting metal free aerial optical fibre cable) |
- |
0 |
|
- |
| 3.4(Technical Requirements) |
- |
4500 |
|
- |
| 3.5(Mechanical Characteristics) |
- |
4500 |
|
- |
| 3.6(Environmental Characteristic of Fibre) |
- |
4500 |
|
- |
| 3.7(Optical Fibre Cable Construction Specifications) |
- |
1000 |
|
- |
| 3.8(Mechanical Characteristics and Tests on Optical Fibre Cable) |
- |
110000 |
|
- |
| 4(Marking) |
- |
500 |
|
- |
| 3.1(Design and construction of aerial metal free optical fibre cable) |
- |
0 |
|
- |
| 3.2(Fibre used in the cable) |
- |
0 |
|
- |
| 3.3(Self-supporting metal free aerial optical fibre cable) |
- |
0 |
|
- |
| 3.4(Technical Requirements) |
- |
4500 |
|
- |
| 3.5(Mechanical Characteristics) |
- |
4500 |
|
- |
| 3.6(Environmental Characteristic of Fibre) |
- |
4500 |
|
- |
| 3.7(Optical Fibre Cable Construction Specifications) |
- |
1000 |
|
- |
| 3.8(Mechanical Characteristics and Tests on Optical Fibre Cable) |
- |
110000 |
|
- |
| 4(Marking) |
- |
500 |
|
- |
|
31 Dec, 2026 |
-
Included w.e.f.02.06.2025 |
| 5144 |
Sleen India Biz venture Private Limited, Agra
| 9139736
| IS 17483 : Part 2 (2020) |
Geosynthetics - Geocells - Specification Part 2 Slope Erosion Protection Application |
All Grade |
165000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 1(Density- IS 13360 (part-3) sec-10) |
- |
500 |
|
- |
| 1(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h- IS 16346) |
- |
5000 |
|
- |
| 1(Environmental stress crack resistance (ESCR), 5000 h - IS 17483 (part-2) Annex C) |
- |
5000 |
|
- |
| 1(Carbon black content- IS 2530) |
- |
1000 |
|
- |
| 1(cell wall thickness at a pressure of 2 ± 0.01 kPa- IS 13162 (part-3)) |
- |
500 |
|
- |
| 1("Seam peel-strength per 25 mm of cell depth-
IS 17369 (part-1) method-B") |
- |
500 |
|
- |
| 1("Seam weld hang strength for 100 mm of seam weld under constant
dead weight of 72.5 kg for 7 days at 54 ± 2 °C-
IS 17483 (part-2)Annex D") |
- |
20000 |
|
- |
| 1("Retention of breaking strength after UV exposure of 500 h-
IS 17483 (part-2) Annex-E") |
- |
40000 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
500 |
|
- |
| Clause No. 5.4(Perforations) |
- |
500 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
500 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
500 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
500 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
500 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
500 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
20000 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
70000 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
40000 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
5000 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
10000 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
500 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
500 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
1000 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
500 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
500 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
5000 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
1000 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
500 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
500 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
20000 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
70000 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
40000 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
5000 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
10000 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
500 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
1000 |
|
- |
| 1("Friction efficiency-
IS 17483 (part-2)Annex F") |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| 1(Density- IS 13360 (part-3) sec-10) |
- |
0 |
|
- |
| 1(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h- IS 16346) |
- |
0 |
|
- |
| 1(Environmental stress crack resistance (ESCR), 5000 h - IS 17483 (part-2) Annex C) |
- |
0 |
|
- |
| 1(Carbon black content- IS 2530) |
- |
0 |
|
- |
| 1(cell wall thickness at a pressure of 2 ± 0.01 kPa- IS 13162 (part-3)) |
- |
0 |
|
- |
| 1("Seam peel-strength per 25 mm of cell depth-
IS 17369 (part-1) method-B") |
- |
0 |
|
- |
| 1("Seam weld hang strength for 100 mm of seam weld under constant
dead weight of 72.5 kg for 7 days at 54 ± 2 °C-
IS 17483 (part-2)Annex D") |
- |
0 |
|
- |
| 1("Retention of breaking strength after UV exposure of 500 h-
IS 17483 (part-2) Annex-E") |
- |
0 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
0 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
0 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
0 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
0 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
0 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
0 |
|
- |
| 1("Friction efficiency-
IS 17483 (part-2)Annex F") |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| 1(Density- IS 13360 (part-3) sec-10) |
- |
0 |
|
- |
| 1(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h- IS 16346) |
- |
0 |
|
- |
| 1(Environmental stress crack resistance (ESCR), 5000 h - IS 17483 (part-2) Annex C) |
- |
0 |
|
- |
| 1(Carbon black content- IS 2530) |
- |
0 |
|
- |
| 1(cell wall thickness at a pressure of 2 ± 0.01 kPa- IS 13162 (part-3)) |
- |
0 |
|
- |
| 1("Seam peel-strength per 25 mm of cell depth-
IS 17369 (part-1) method-B") |
- |
0 |
|
- |
| 1("Seam weld hang strength for 100 mm of seam weld under constant
dead weight of 72.5 kg for 7 days at 54 ± 2 °C-
IS 17483 (part-2)Annex D") |
- |
0 |
|
- |
| 1("Retention of breaking strength after UV exposure of 500 h-
IS 17483 (part-2) Annex-E") |
- |
0 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
0 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
0 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
0 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
0 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
0 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
0 |
|
- |
| 1("Friction efficiency-
IS 17483 (part-2)Annex F") |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| 1(Density- IS 13360 (part-3) sec-10) |
- |
0 |
|
- |
| 1(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h- IS 16346) |
- |
0 |
|
- |
| 1(Environmental stress crack resistance (ESCR), 5000 h - IS 17483 (part-2) Annex C) |
- |
0 |
|
- |
| 1(Carbon black content- IS 2530) |
- |
0 |
|
- |
| 1(cell wall thickness at a pressure of 2 ± 0.01 kPa- IS 13162 (part-3)) |
- |
0 |
|
- |
| 1("Seam peel-strength per 25 mm of cell depth-
IS 17369 (part-1) method-B") |
- |
0 |
|
- |
| 1("Seam weld hang strength for 100 mm of seam weld under constant
dead weight of 72.5 kg for 7 days at 54 ± 2 °C-
IS 17483 (part-2)Annex D") |
- |
0 |
|
- |
| 1("Retention of breaking strength after UV exposure of 500 h-
IS 17483 (part-2) Annex-E") |
- |
0 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
0 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
0 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
0 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
0 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
0 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
0 |
|
- |
| 1("Friction efficiency-
IS 17483 (part-2)Annex F") |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| 1(Density- IS 13360 (part-3) sec-10) |
- |
0 |
|
- |
| 1(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h- IS 16346) |
- |
0 |
|
- |
| 1(Environmental stress crack resistance (ESCR), 5000 h - IS 17483 (part-2) Annex C) |
- |
0 |
|
- |
| 1(Carbon black content- IS 2530) |
- |
0 |
|
- |
| 1(cell wall thickness at a pressure of 2 ± 0.01 kPa- IS 13162 (part-3)) |
- |
0 |
|
- |
| 1("Seam peel-strength per 25 mm of cell depth-
IS 17369 (part-1) method-B") |
- |
0 |
|
- |
| 1("Seam weld hang strength for 100 mm of seam weld under constant
dead weight of 72.5 kg for 7 days at 54 ± 2 °C-
IS 17483 (part-2)Annex D") |
- |
0 |
|
- |
| 1("Retention of breaking strength after UV exposure of 500 h-
IS 17483 (part-2) Annex-E") |
- |
0 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
0 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.2(Dimensions) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 5.4(Perforations) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
0 |
|
- |
| Clause No. 5.5(Seam Weld) |
- |
0 |
|
- |
| Clause No. 5.3(Surface density of indentation) |
- |
0 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
0 |
|
- |
| Clause No. 5.3(Asperity height) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (i)(Density, g/cm3) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ii)(Environmental stress crack resistance – Notched constant tensile load (ESCR - NCTL), 400 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iv)(Carbon black content, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (v)(Post texturing strip/cell wall thickness at a pressure of 2 ± 0.01 kPa, mm) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vi)(Seam peel-strength per 25 mm of cell depth, N) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (vii)(Seam weld hang strength for 100 mm of seam weld under constantdead weight of 72.5 kg for 7 days at 54 ± 2 °C) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (viii)(Resistance to oxidation, Retained tensile strength, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (ix)(Retention of breaking strength after UV exposure of 500 h) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (x)(Friction efficiency, percent) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xi)(Standard oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (xii)(High pressure oxidative induction time, minutes) |
- |
0 |
|
- |
| Clause No. 8(Geocells panel packaging) |
- |
0 |
|
- |
| Clause No. 9.1(Geocells labelling, shipment, storage and handling) |
- |
0 |
|
- |
| 1("Friction efficiency-
IS 17483 (part-2)Annex F") |
- |
0 |
|
- |
| Clause No. 6.2, Table No. 1 (iii)(Environmental stress crack resistance (ESCR), 5000 h) |
- |
0 |
|
- |
|
- |
-
Included w.e.f.23.07.2025
Exclusion
Clause No. 6.2, Table No. 1 (xii) (High pressure oxidative induction time, minutes)
Clause No. 6.2, Table No. 1 (xii) (High pressure oxidative induction time, minutes) |
| 5145 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 16392 (2015) |
Geosynthetics - Geotextiles for permanent erosion control in hard armor systems - Specification |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 4.3 Table 1 (i) (d) (Grab strength, N) |
- |
|
|
|
| Cl 4.3 Table 1 (i) (e) (Sewn seam strength, N) |
- |
|
|
|
| Cl 4.3 Table 1 (i) (f) (Trapezidal tear strength, N) |
- |
|
|
|
| Cl 4.3 Table 1 (i) (h) (CBR puncture strength, N) |
- |
|
|
|
| Cl 4.3 Table 1 (i) (b) (Roll length, m) |
- |
|
|
|
| Cl 4.3 Table 1 (i) (c) (Roll width, m) |
- |
|
|
|
| Cl 4.3 Table 1 (ii) (b) (Permitttivity, s-1 , Course) |
- |
|
|
|
| Cl 4.3 Table 1 (ii) (c) (Apparent Opening Size (AOS), mm, Medium) |
- |
|
|
|
| 4.2, Amd-1 (Carbon Black content & Dispersion) |
- |
|
|
|
|
- |
-
Partial test facility only |
| 5146 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 16393 (2015) |
Geosynthetics - Geotextiles used in subsurface drainage application - Specification |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 1 (Roll length- IS 1954) |
- |
|
|
|
| 1 (Roll width- IS 1954) |
- |
|
|
|
| 1 (Grab strength- IS 16342) |
- |
|
|
|
| 1 (Sewn seam strength- IS 15060) |
- |
|
|
|
| 1 (Trapezidal tear strength- IS 14293) |
- |
|
|
|
| 1 (CBR puncture strength- IS 16078) |
- |
|
|
|
| 1 (Permitttivity- IS 14324) |
- |
|
|
|
| 1 (Apparent opening size (AOS)- IS 14294) |
- |
|
|
|
| 6 (Marking and Labelling) |
- |
|
|
|
| 4.2 (type of polymer) |
- |
|
|
|
| 4.2 (carbon black content and dispersion) |
- |
|
|
|
|
- |
-
Partial test facility only |
| 5147 |
JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR
| 9164606
| IS 1610 (2018) |
Household sewing machines - General requirements (Fourth Revision) |
- |
9000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3.1(Driving arrangement Hand Operated Sewing Machine) |
- |
2500 |
|
For complete Cl. 3, 5, 6 and 7 |
| 4.1(Sewing Mechanism Design ) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 4.2(Sewing Mechanism Reverse stitch mechanism ) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 4.2.1(Sewing Mechanism Stitch Regulator) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 4.3(Sewing Mechanism Thread Tension) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 4.4(Sewing Mechanism Timing) |
- |
2000 |
|
For complete Cl. 4 and 8 |
| 4.7(Sewing Mechanism Thread Spool Pin) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 6(Lubrication) |
- |
1999.99 |
|
For complete Cl. 4, 8 and 12 |
| 8(WORKMANSHIP AND FINISH) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 8(WORKMANSHIP AND FINISH) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 8(WORKMANSHIP AND FINISH) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 10.1 IS 7491 (Accuracy Requirement Functional Dimension Feed Dog Measuring Condition - Feed dog raised to its highest position ) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Functional Dimension Presser foot Measuring Condition - Presser foot in lifted condition) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Flywheel Measuring Condition - Rotate flywheel to Radially measure eccentrity) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Feed section Measuring Condition - At its highest position above needle place) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.2 IS 7492 (Sewing Requirement) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.2 IS 7492 (Sewing Requirement) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.2 IS 7492 (Sewing Requirement) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.2 IS 7492 (Sewing Requirement) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.2 IS 7492 (Sewing Requirement) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.3 IS 7493 (Durability Requirement Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.3 IS 7493 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between two indicator readings when needle bar is at its highest
and lowest position) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.3 IS 7493 (Durability requirement Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 10.3 IS 7493 (Durability Requirement Feed section Measuring Condition - At its highest position above needle place) |
- |
4500 |
|
For complete Cl. 10.1, 10.2 and 10.3 |
| 12(Marking) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 12(Marking) |
- |
2000 |
|
For complete Cl. 4, 8 and 12 |
| 3.1(Driving arrangement Hand Operated Sewing Machine) |
- |
0 |
|
- |
| 4.1(Sewing Mechanism Design ) |
- |
0 |
|
- |
| 4.2(Sewing Mechanism Reverse stitch mechanism ) |
- |
0 |
|
- |
| 4.2.1(Sewing Mechanism Stitch Regulator) |
- |
0 |
|
- |
| 4.3(Sewing Mechanism Thread Tension) |
- |
0 |
|
- |
| 4.4(Sewing Mechanism Timing) |
- |
0 |
|
- |
| 4.7(Sewing Mechanism Thread Spool Pin) |
- |
0 |
|
- |
| 6(Lubrication) |
- |
0 |
|
- |
| 8(WORKMANSHIP AND FINISH) |
- |
0 |
|
- |
| 8(WORKMANSHIP AND FINISH) |
- |
0 |
|
- |
| 8(WORKMANSHIP AND FINISH) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Functional Dimension Feed Dog Measuring Condition - Feed dog raised to its highest position ) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Functional Dimension Shuttle and shuttle driver Measuring Condition - Shuttle heel at bottom - most position) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Functional Dimension Presser foot Measuring Condition - Presser foot in lifted condition) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Needle bar Measuring Condition - Needle bar at lower-most condition) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between highest & lowest position of needle bar.) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Flywheel Measuring Condition - Rotate flywheel to Radially measure eccentrity) |
- |
0 |
|
- |
| 10.1 IS 7491 (Accuracy Requirement Assembly Clearance Feed section Measuring Condition - At its highest position above needle place) |
- |
0 |
|
- |
| 10.2 IS 7492 (Sewing Requirement) |
- |
0 |
|
- |
| 10.2 IS 7492 (Sewing Requirement) |
- |
0 |
|
- |
| 10.2 IS 7492 (Sewing Requirement) |
- |
0 |
|
- |
| 10.2 IS 7492 (Sewing Requirement) |
- |
0 |
|
- |
| 10.2 IS 7492 (Sewing Requirement) |
- |
0 |
|
- |
| 10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition) |
- |
0 |
|
- |
| 10.3 IS 7493 (Durability Requirement Needle bar Measuring Condition - Needle bar at lower-most condition) |
- |
0 |
|
- |
| 10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position) |
- |
0 |
|
- |
| 10.3 IS 7493 (Durability Requirement Thread take up lever Measuring Condition - Thread take up lever at top and intermediate position) |
- |
0 |
|
- |
| 10.3 IS 7493 (Durability Requirement Shuttle Measuring Condition - Tip of pin at top most bottom most position of needle bar) |
- |
0 |
|
- |
| 10.3 IS 7493 (Accuracy Requirement Assembly Clearance Shuttle Measuring Condition - Difference between two indicator readings when needle bar is at its highest
and lowest position) |
- |
0 |
|
- |
| 10.3 IS 7493 (Durability requirement Arm shaft Measuring Condition -At different fly wheel position (turn fly wheel by hand) axial push./pull to be given) |
- |
0 |
|
- |
| 10.3 IS 7493 (Durability Requirement Feed section Measuring Condition - At its highest position above needle place) |
- |
0 |
|
- |
| 12(Marking) |
- |
0 |
|
- |
| 12(Marking) |
- |
0 |
|
- |
|
- |
-
Included w.e.f 24.06.2025 |
| 5148 |
ATCC TEST LABS LLP
| 8172626
| IS 7098 : Part 1 (1988) |
Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision) |
- |
10000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3(CONDUCTOR: MATERIALS) |
- |
500 |
|
Rs.10000/- for single core sheathed cable, Rs.1000/- for Each additional core, Rs.3000/- for armoured cable, Rs.5000/- for category C1 and Rs.10000/- for category C2 |
| 4(INSULATION : MATERIALS) |
- |
500 |
|
- |
| 5.1(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 5.2(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 6(ARMOURING) |
- |
500 |
|
- |
| 7(OUTER SHEATH) |
- |
500 |
|
- |
| 8.1(CONDUCTOR: CONSTRUCTION) |
- |
500 |
|
- |
| 8.2(PROTECTIVE BARRIER) |
- |
500 |
|
- |
| 8.3(SIZE OF NEUTRAL CONDUCTOR) |
- |
500 |
|
- |
| 9.1(Insulation Applied by extrusicn) |
- |
500 |
|
- |
| 9.2(Thickness of Insulation - Average) |
- |
1000 |
|
- |
| 9.3(Thickness of Insulation - Minimum) |
- |
1000 |
|
- |
| 9.4(Application of Insulation) |
- |
500 |
|
- |
| 10.1(Core Identification) |
- |
500 |
|
- |
| 10.2(Core Identification- Neutral) |
- |
500 |
|
- |
| 10.3(Core Identification by number ) |
- |
500 |
|
- |
| 10.4(Core Identification by number - Neutral ) |
- |
500 |
|
- |
| 11(LAVING UP OF CORES) |
- |
500 |
|
- |
| 12.1 & 12.2(Inner sheath : Application) |
- |
500 |
|
- |
| 12.3(Thickness of Inner Sheath) |
- |
1000 |
|
- |
| 13.1(Armouring: Application) |
- |
500 |
|
- |
| 13.1.2(Armouring: Coverage ) |
- |
1000 |
|
- |
| 13.1.3(Armouring: Direction of Lay ) |
- |
1000 |
|
- |
| 13.2(Type of armour ) |
- |
500 |
|
- |
| 13.3(Armouring : Dimensions -Wire Diameter) |
- |
1000 |
|
- |
| 13.3(Armouring : Dimensions -Formed wire ) |
- |
1000 |
|
- |
| 13.4(Armour: Joint) |
- |
5000 |
|
- |
| 13.5(Armouring : Resistance Test) |
- |
1000 |
|
- |
| 13.6 a)(ARMOURING: Tensile Strength) |
- |
1000 |
|
- |
| 13.6 b)(ARMOURING: Elongation ) |
- |
1000 |
|
- |
| 13.6 c)(ARMOURING: Torsion Test (For round wire ) ) |
- |
1000 |
|
- |
| 13.6 d)(ARMOURING: Winding Test(For formed wire)) |
- |
1000 |
|
- |
| 13.6 e)(ARMOURING: Uniformity of zinc coating) |
- |
1000 |
|
- |
| 13.6 f)(ARMOURING: Mass of zinc coating ) |
- |
1000 |
|
- |
| 13.6 g)(ARMOURING: Resistivity) |
- |
1000 |
|
- |
| 14.1(Outer Sheath : Application) |
- |
500 |
|
- |
| 14.2(Colour of outer sheath) |
- |
500 |
|
- |
| 14.3(Thickness of outer sheath - AVERAGE) |
- |
1000 |
|
- |
| 14.3(Thickness of outer sheath - minimum) |
- |
1000 |
|
- |
| 15.1 a) i)(Annealing Test ( For copper wire ) ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - Before stranding ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - After stranding ) |
- |
1000 |
|
- |
| 15.1 a) iii)(Wrapping test (for aluminium)) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Main conductor) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Neutral conductor) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Tensile Test) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Elongation) |
- |
1000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation ) |
- |
2000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation ) |
- |
2000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Hot set ) |
- |
1000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Permanent set ) |
- |
1000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 d) v) (Insulation: Waterabsorption(gravimetric)) |
- |
4000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Tensile stregth) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation ) |
- |
2000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation ) |
- |
2000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation ) |
- |
2000 |
|
- |
| 15.1 e) iii) (Sheath: Loss of mass in air oven) |
- |
2000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 e) v) (Sheath : Hot deformation) |
- |
1000 |
|
- |
| 15.1 e) vi) (Sheath : Heat shock test) |
- |
1000 |
|
- |
| 15.1 e) vii) (Sheath : Thermalstability) |
- |
1000 |
|
- |
| 15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity ) |
- |
1000 |
|
- |
| 16.2(HIGH VOLTAGE TEST ) |
- |
1000 |
|
- |
| 16.3(FLAMMABILITY TEST : Period of Burning ) |
- |
1000 |
|
- |
| 16.3(FLAMMABILITY TEST : Unaffected length ) |
- |
1000 |
|
- |
| 16.9(Oxygen Index Test) |
- |
2000 |
|
- |
| 16.1(Flame Retardance Test on Single Cables) |
- |
1000 |
|
- |
| 16.11(Flame Retardance Test on Bunched Cables) |
- |
5000 |
|
- |
| 16.13(Test for Halogen Acid Gas Evolution) |
- |
2000 |
|
- |
| 16.14(Temperature Index) |
- |
2000 |
|
- |
| 17.1(Manufacturer'. identification) |
- |
500 |
|
- |
| 17.2(cable Indentification ) |
- |
500 |
|
- |
| 17.3(cable Code ) |
- |
500 |
|
- |
| 15.4 (a)(Cold bend) |
- |
1000 |
|
- |
| 15.4 (b)(Cold impact) |
- |
1000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
2000 |
|
- |
| Table 4(Copper purity test) |
- |
2000 |
|
- |
| Cl No. 16.15(Smoke density test) |
- |
2000 |
|
- |
| Table 2(Cold Impact test for Outer sheath) |
- |
1000 |
|
- |
| Table 2(Cold bend test for Outer sheath) |
- |
1000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
2000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
2000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
2000 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.15.4(Cold Bend Test (for outer sheath)) |
- |
500 |
|
- |
| Cl.15.4(Cold Impact Test (For outer sheath)) |
- |
1000 |
|
- |
| Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables)) |
- |
1000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Elongation) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth ) |
- |
2000 |
|
- |
| 3(CONDUCTOR: MATERIALS) |
- |
500 |
|
- |
| 4(INSULATION : MATERIALS) |
- |
500 |
|
- |
| 5.1(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 5.2(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 6(ARMOURING) |
- |
500 |
|
- |
| 7(OUTER SHEATH) |
- |
500 |
|
- |
| 8.1(CONDUCTOR: CONSTRUCTION) |
- |
500 |
|
- |
| 8.2(PROTECTIVE BARRIER) |
- |
500 |
|
- |
| 8.3(SIZE OF NEUTRAL CONDUCTOR) |
- |
500 |
|
- |
| 9.1(Insulation Applied by extrusicn) |
- |
500 |
|
- |
| 9.2(Thickness of Insulation - Average) |
- |
1000 |
|
- |
| 9.3(Thickness of Insulation - Minimum) |
- |
1000 |
|
- |
| 9.4(Application of Insulation) |
- |
500 |
|
- |
| 10.1(Core Identification) |
- |
500 |
|
- |
| 10.2(Core Identification- Neutral) |
- |
500 |
|
- |
| 10.3(Core Identification by number ) |
- |
500 |
|
- |
| 10.4(Core Identification by number - Neutral ) |
- |
500 |
|
- |
| 11(LAVING UP OF CORES) |
- |
500 |
|
- |
| 12.1 & 12.2(Inner sheath : Application) |
- |
500 |
|
- |
| 12.3(Thickness of Inner Sheath) |
- |
1000 |
|
- |
| 13.1(Armouring: Application) |
- |
500 |
|
- |
| 13.1.2(Armouring: Coverage ) |
- |
1000 |
|
- |
| 13.1.3(Armouring: Direction of Lay ) |
- |
500 |
|
- |
| 13.2(Type of armour ) |
- |
500 |
|
- |
| 13.3(Armouring : Dimensions -Wire Diameter) |
- |
1000 |
|
- |
| 13.3(Armouring : Dimensions -Formed wire ) |
- |
1000 |
|
- |
| 13.4(Armour: Joint) |
- |
500 |
|
- |
| 13.5(Armouring : Resistance Test) |
- |
1000 |
|
- |
| 13.6 a)(ARMOURING: Tensile Strength) |
- |
1000 |
|
- |
| 13.6 b)(ARMOURING: Elongation ) |
- |
1000 |
|
- |
| 13.6 c)(ARMOURING: Torsion Test (For round wire ) ) |
- |
1000 |
|
- |
| 13.6 d)(ARMOURING: Winding Test(For formed wire)) |
- |
1000 |
|
- |
| 13.6 e)(ARMOURING: Uniformity of zinc coating) |
- |
1000 |
|
- |
| 13.6 f)(ARMOURING: Mass of zinc coating ) |
- |
1000 |
|
- |
| 13.6 g)(ARMOURING: Resistivity) |
- |
1000 |
|
- |
| 14.1(Outer Sheath : Application) |
- |
1000 |
|
- |
| 14.2(Colour of outer sheath) |
- |
1000 |
|
- |
| 14.3(Thickness of outer sheath - AVERAGE) |
- |
1000 |
|
- |
| 14.3(Thickness of outer sheath - minimum) |
- |
1000 |
|
- |
| 15.1 a) i)(Annealing Test ( For copper wire ) ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - Before stranding ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - After stranding ) |
- |
1000 |
|
- |
| 15.1 a) iii)(Wrapping test (for aluminium)) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Main conductor) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Neutral conductor) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Tensile Test) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Elongation) |
- |
1000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation ) |
- |
2000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation ) |
- |
2000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Hot set ) |
- |
1000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Permanent set ) |
- |
1000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 d) v) (Insulation: Waterabsorption(gravimetric)) |
- |
5000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Tensile stregth) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation ) |
- |
2000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation ) |
- |
2000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation ) |
- |
2000 |
|
- |
| 15.1 e) iii) (Sheath: Loss of mass in air oven) |
- |
2000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 e) v) (Sheath : Hot deformation) |
- |
1000 |
|
- |
| 15.1 e) vi) (Sheath : Heat shock test) |
- |
1000 |
|
- |
| 15.1 e) vii) (Sheath : Thermalstability) |
- |
1000 |
|
- |
| 15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity ) |
- |
1000 |
|
- |
| 16.2(HIGH VOLTAGE TEST ) |
- |
1000 |
|
- |
| 16.3(FLAMMABILITY TEST : Period of Burning ) |
- |
1000 |
|
- |
| 16.3(FLAMMABILITY TEST : Unaffected length ) |
- |
1000 |
|
- |
| 16.9(Oxygen Index Test) |
- |
2000 |
|
- |
| 16.1(Flame Retardance Test on Single Cables) |
- |
1000 |
|
- |
| 16.11(Flame Retardance Test on Bunched Cables) |
- |
5000 |
|
- |
| 16.13(Test for Halogen Acid Gas Evolution) |
- |
2000 |
|
- |
| 16.14(Temperature Index) |
- |
2000 |
|
- |
| 17.1(Manufacturer'. identification) |
- |
500 |
|
- |
| 17.2(cable Indentification ) |
- |
500 |
|
- |
| 17.3(cable Code ) |
- |
500 |
|
- |
| 15.4 (a)(Cold bend) |
- |
1000 |
|
- |
| 15.4 (b)(Cold impact) |
- |
1000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
2000 |
|
- |
| Table 4(Copper purity test) |
- |
5000 |
|
- |
| Cl No. 16.15(Smoke density test) |
- |
2000 |
|
- |
| Table 2(Cold Impact test for Outer sheath) |
- |
1000 |
|
- |
| Table 2(Cold bend test for Outer sheath) |
- |
1000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
2000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
2000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
2000 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.15.4(Cold Bend Test (for outer sheath)) |
- |
1000 |
|
- |
| Cl.15.4(Cold Impact Test (For outer sheath)) |
- |
1000 |
|
- |
| Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables)) |
- |
1000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Elongation) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth ) |
- |
2000 |
|
- |
| 3(CONDUCTOR: MATERIALS) |
- |
500 |
|
- |
| 4(INSULATION : MATERIALS) |
- |
500 |
|
- |
| 5.1(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 5.2(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 6(ARMOURING) |
- |
500 |
|
- |
| 7(OUTER SHEATH) |
- |
500 |
|
- |
| 8.1(CONDUCTOR: CONSTRUCTION) |
- |
500 |
|
- |
| 8.2(PROTECTIVE BARRIER) |
- |
500 |
|
- |
| 8.3(SIZE OF NEUTRAL CONDUCTOR) |
- |
500 |
|
- |
| 9.1(Insulation Applied by extrusicn) |
- |
500 |
|
- |
| 9.2(Thickness of Insulation - Average) |
- |
1000 |
|
- |
| 9.3(Thickness of Insulation - Minimum) |
- |
1000 |
|
- |
| 9.4(Application of Insulation) |
- |
500 |
|
- |
| 10.1(Core Identification) |
- |
500 |
|
- |
| 10.2(Core Identification- Neutral) |
- |
500 |
|
- |
| 10.3(Core Identification by number ) |
- |
500 |
|
- |
| 10.4(Core Identification by number - Neutral ) |
- |
500 |
|
- |
| 11(LAVING UP OF CORES) |
- |
500 |
|
- |
| 12.1 & 12.2(Inner sheath : Application) |
- |
500 |
|
- |
| 12.3(Thickness of Inner Sheath) |
- |
1000 |
|
- |
| 13.1(Armouring: Application) |
- |
500 |
|
- |
| 13.1.2(Armouring: Coverage ) |
- |
1000 |
|
- |
| 13.1.3(Armouring: Direction of Lay ) |
- |
500 |
|
- |
| 13.2(Type of armour ) |
- |
500 |
|
- |
| 13.3(Armouring : Dimensions -Wire Diameter) |
- |
1000 |
|
- |
| 13.3(Armouring : Dimensions -Formed wire ) |
- |
1000 |
|
- |
| 13.4(Armour: Joint) |
- |
500 |
|
- |
| 13.5(Armouring : Resistance Test) |
- |
1000 |
|
- |
| 13.6 a)(ARMOURING: Tensile Strength) |
- |
1000 |
|
- |
| 13.6 b)(ARMOURING: Elongation ) |
- |
1000 |
|
- |
| 13.6 c)(ARMOURING: Torsion Test (For round wire ) ) |
- |
1000 |
|
- |
| 13.6 d)(ARMOURING: Winding Test(For formed wire)) |
- |
1000 |
|
- |
| 13.6 e)(ARMOURING: Uniformity of zinc coating) |
- |
1000 |
|
- |
| 13.6 f)(ARMOURING: Mass of zinc coating ) |
- |
1000 |
|
- |
| 13.6 g)(ARMOURING: Resistivity) |
- |
1000 |
|
- |
| 14.1(Outer Sheath : Application) |
- |
500 |
|
- |
| 14.2(Colour of outer sheath) |
- |
500 |
|
- |
| 14.3(Thickness of outer sheath - AVERAGE) |
- |
1000 |
|
- |
| 14.3(Thickness of outer sheath - minimum) |
- |
1000 |
|
- |
| 15.1 a) i)(Annealing Test ( For copper wire ) ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - Before stranding ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - After stranding ) |
- |
1000 |
|
- |
| 15.1 a) iii)(Wrapping test (for aluminium)) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Main conductor) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Neutral conductor) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Tensile Test) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Elongation) |
- |
1000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation ) |
- |
2000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation ) |
- |
2000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Hot set ) |
- |
2000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Permanent set ) |
- |
2000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 d) v) (Insulation: Waterabsorption(gravimetric)) |
- |
5000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Tensile stregth) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation ) |
- |
2000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation ) |
- |
2000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation ) |
- |
2000 |
|
- |
| 15.1 e) iii) (Sheath: Loss of mass in air oven) |
- |
2000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 e) v) (Sheath : Hot deformation) |
- |
1000 |
|
- |
| 15.1 e) vi) (Sheath : Heat shock test) |
- |
1000 |
|
- |
| 15.1 e) vii) (Sheath : Thermalstability) |
- |
1000 |
|
- |
| 15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity ) |
- |
1000 |
|
- |
| 16.2(HIGH VOLTAGE TEST ) |
- |
2000 |
|
- |
| 16.3(FLAMMABILITY TEST : Period of Burning ) |
- |
1000 |
|
- |
| 16.3(FLAMMABILITY TEST : Unaffected length ) |
- |
1000 |
|
- |
| 16.9(Oxygen Index Test) |
- |
5000 |
|
- |
| 16.1(Flame Retardance Test on Single Cables) |
- |
1000 |
|
- |
| 16.11(Flame Retardance Test on Bunched Cables) |
- |
5000 |
|
- |
| 16.13(Test for Halogen Acid Gas Evolution) |
- |
3000 |
|
- |
| 16.14(Temperature Index) |
- |
5000 |
|
- |
| 17.1(Manufacturer'. identification) |
- |
500 |
|
- |
| 17.2(cable Indentification ) |
- |
500 |
|
- |
| 17.3(cable Code ) |
- |
500 |
|
- |
| 15.4 (a)(Cold bend) |
- |
1000 |
|
- |
| 15.4 (b)(Cold impact) |
- |
1000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
2000 |
|
- |
| Table 4(Copper purity test) |
- |
5000 |
|
- |
| Cl No. 16.15(Smoke density test) |
- |
5000 |
|
- |
| Table 2(Cold Impact test for Outer sheath) |
- |
1000 |
|
- |
| Table 2(Cold bend test for Outer sheath) |
- |
1000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.15.4(Cold Bend Test (for outer sheath)) |
- |
1000 |
|
- |
| Cl.15.4(Cold Impact Test (For outer sheath)) |
- |
1000 |
|
- |
| Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables)) |
- |
1000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Elongation) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth ) |
- |
2000 |
|
- |
| 3(CONDUCTOR: MATERIALS) |
- |
500 |
|
- |
| 4(INSULATION : MATERIALS) |
- |
500 |
|
- |
| 5.1(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 5.2(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 6(ARMOURING) |
- |
500 |
|
- |
| 7(OUTER SHEATH) |
- |
500 |
|
- |
| 8.1(CONDUCTOR: CONSTRUCTION) |
- |
500 |
|
- |
| 8.2(PROTECTIVE BARRIER) |
- |
500 |
|
- |
| 8.3(SIZE OF NEUTRAL CONDUCTOR) |
- |
500 |
|
- |
| 9.1(Insulation Applied by extrusicn) |
- |
500 |
|
- |
| 9.2(Thickness of Insulation - Average) |
- |
1000 |
|
- |
| 9.3(Thickness of Insulation - Minimum) |
- |
1000 |
|
- |
| 9.4(Application of Insulation) |
- |
500 |
|
- |
| 10.1(Core Identification) |
- |
500 |
|
- |
| 10.2(Core Identification- Neutral) |
- |
500 |
|
- |
| 10.3(Core Identification by number ) |
- |
500 |
|
- |
| 10.4(Core Identification by number - Neutral ) |
- |
500 |
|
- |
| 11(LAVING UP OF CORES) |
- |
500 |
|
- |
| 12.1 & 12.2(Inner sheath : Application) |
- |
500 |
|
- |
| 12.3(Thickness of Inner Sheath) |
- |
1000 |
|
- |
| 13.1(Armouring: Application) |
- |
500 |
|
- |
| 13.1.2(Armouring: Coverage ) |
- |
1000 |
|
- |
| 13.1.3(Armouring: Direction of Lay ) |
- |
500 |
|
- |
| 13.2(Type of armour ) |
- |
500 |
|
- |
| 13.3(Armouring : Dimensions -Wire Diameter) |
- |
1000 |
|
- |
| 13.3(Armouring : Dimensions -Formed wire ) |
- |
1000 |
|
- |
| 13.4(Armour: Joint) |
- |
1000 |
|
- |
| 13.5(Armouring : Resistance Test) |
- |
1000 |
|
- |
| 13.6 a)(ARMOURING: Tensile Strength) |
- |
1000 |
|
- |
| 13.6 b)(ARMOURING: Elongation ) |
- |
1000 |
|
- |
| 13.6 c)(ARMOURING: Torsion Test (For round wire ) ) |
- |
1000 |
|
- |
| 13.6 d)(ARMOURING: Winding Test(For formed wire)) |
- |
1000 |
|
- |
| 13.6 e)(ARMOURING: Uniformity of zinc coating) |
- |
1000 |
|
- |
| 13.6 f)(ARMOURING: Mass of zinc coating ) |
- |
1000 |
|
- |
| 13.6 g)(ARMOURING: Resistivity) |
- |
1000 |
|
- |
| 14.1(Outer Sheath : Application) |
- |
500 |
|
- |
| 14.2(Colour of outer sheath) |
- |
500 |
|
- |
| 14.3(Thickness of outer sheath - AVERAGE) |
- |
1000 |
|
- |
| 14.3(Thickness of outer sheath - minimum) |
- |
1000 |
|
- |
| 15.1 a) i)(Annealing Test ( For copper wire ) ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - Before stranding ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - After stranding ) |
- |
1000 |
|
- |
| 15.1 a) iii)(Wrapping test (for aluminium)) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Main conductor) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Neutral conductor) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Tensile Test) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Elongation) |
- |
1000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation ) |
- |
2000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation ) |
- |
2000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Hot set ) |
- |
2000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Permanent set ) |
- |
2000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 d) v) (Insulation: Waterabsorption(gravimetric)) |
- |
5000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Tensile stregth) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation ) |
- |
2000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation ) |
- |
2000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation ) |
- |
2000 |
|
- |
| 15.1 e) iii) (Sheath: Loss of mass in air oven) |
- |
2000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 e) v) (Sheath : Hot deformation) |
- |
1000 |
|
- |
| 15.1 e) vi) (Sheath : Heat shock test) |
- |
1000 |
|
- |
| 15.1 e) vii) (Sheath : Thermalstability) |
- |
1000 |
|
- |
| 15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity ) |
- |
1000 |
|
- |
| 16.2(HIGH VOLTAGE TEST ) |
- |
2000 |
|
- |
| 16.3(FLAMMABILITY TEST : Period of Burning ) |
- |
1000 |
|
- |
| 16.3(FLAMMABILITY TEST : Unaffected length ) |
- |
1000 |
|
- |
| 16.9(Oxygen Index Test) |
- |
5000 |
|
- |
| 16.1(Flame Retardance Test on Single Cables) |
- |
1000 |
|
- |
| 16.11(Flame Retardance Test on Bunched Cables) |
- |
5000 |
|
- |
| 16.13(Test for Halogen Acid Gas Evolution) |
- |
3000 |
|
- |
| 16.14(Temperature Index) |
- |
5000 |
|
- |
| 17.1(Manufacturer'. identification) |
- |
500 |
|
- |
| 17.2(cable Indentification ) |
- |
500 |
|
- |
| 17.3(cable Code ) |
- |
500 |
|
- |
| 15.4 (a)(Cold bend) |
- |
1000 |
|
- |
| 15.4 (b)(Cold impact) |
- |
1000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
2000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
2000 |
|
- |
| Table 4(Copper purity test) |
- |
5000 |
|
- |
| Cl No. 16.15(Smoke density test) |
- |
5000 |
|
- |
| Table 2(Cold Impact test for Outer sheath) |
- |
1000 |
|
- |
| Table 2(Cold bend test for Outer sheath) |
- |
1000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.15.4(Cold Bend Test (for outer sheath)) |
- |
1000 |
|
- |
| Cl.15.4(Cold Impact Test (For outer sheath)) |
- |
1000 |
|
- |
| Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables)) |
- |
1000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Elongation) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth ) |
- |
2000 |
|
- |
| 3(CONDUCTOR: MATERIALS) |
- |
500 |
|
- |
| 4(INSULATION : MATERIALS) |
- |
500 |
|
- |
| 5.1(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 5.2(FILLER AND INNER SHEATH) |
- |
500 |
|
- |
| 6(ARMOURING) |
- |
500 |
|
- |
| 7(OUTER SHEATH) |
- |
500 |
|
- |
| 8.1(CONDUCTOR: CONSTRUCTION) |
- |
500 |
|
- |
| 8.2(PROTECTIVE BARRIER) |
- |
500 |
|
- |
| 8.3(SIZE OF NEUTRAL CONDUCTOR) |
- |
500 |
|
- |
| 9.1(Insulation Applied by extrusicn) |
- |
500 |
|
- |
| 9.2(Thickness of Insulation - Average) |
- |
1000 |
|
- |
| 9.3(Thickness of Insulation - Minimum) |
- |
1000 |
|
- |
| 9.4(Application of Insulation) |
- |
500 |
|
- |
| 10.1(Core Identification) |
- |
500 |
|
- |
| 10.2(Core Identification- Neutral) |
- |
500 |
|
- |
| 10.3(Core Identification by number ) |
- |
500 |
|
- |
| 10.4(Core Identification by number - Neutral ) |
- |
500 |
|
- |
| 11(LAVING UP OF CORES) |
- |
500 |
|
- |
| 12.1 & 12.2(Inner sheath : Application) |
- |
500 |
|
- |
| 12.3(Thickness of Inner Sheath) |
- |
1000 |
|
- |
| 13.1(Armouring: Application) |
- |
500 |
|
- |
| 13.1.2(Armouring: Coverage ) |
- |
1000 |
|
- |
| 13.1.3(Armouring: Direction of Lay ) |
- |
500 |
|
- |
| 13.2(Type of armour ) |
- |
500 |
|
- |
| 13.3(Armouring : Dimensions -Wire Diameter) |
- |
1000 |
|
- |
| 13.3(Armouring : Dimensions -Formed wire ) |
- |
1000 |
|
- |
| 13.4(Armour: Joint) |
- |
500 |
|
- |
| 13.5(Armouring : Resistance Test) |
- |
1000 |
|
- |
| 13.6 a)(ARMOURING: Tensile Strength) |
- |
1000 |
|
- |
| 13.6 b)(ARMOURING: Elongation ) |
- |
1000 |
|
- |
| 13.6 c)(ARMOURING: Torsion Test (For round wire ) ) |
- |
1000 |
|
- |
| 13.6 d)(ARMOURING: Winding Test(For formed wire)) |
- |
1000 |
|
- |
| 13.6 e)(ARMOURING: Uniformity of zinc coating) |
- |
1000 |
|
- |
| 13.6 f)(ARMOURING: Mass of zinc coating ) |
- |
1000 |
|
- |
| 13.6 g)(ARMOURING: Resistivity) |
- |
1000 |
|
- |
| 14.1(Outer Sheath : Application) |
- |
500 |
|
- |
| 14.2(Colour of outer sheath) |
- |
500 |
|
- |
| 14.3(Thickness of outer sheath - AVERAGE) |
- |
1000 |
|
- |
| 14.3(Thickness of outer sheath - minimum) |
- |
1000 |
|
- |
| 15.1 a) i)(Annealing Test ( For copper wire ) ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - Before stranding ) |
- |
1000 |
|
- |
| 15.1 a) ii)(Tensile test (for aluminium) - After stranding ) |
- |
1000 |
|
- |
| 15.1 a) iii)(Wrapping test (for aluminium)) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Main conductor) |
- |
1000 |
|
- |
| 15.1 a) iv)(Resistance test - Neutral conductor) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Tensile Test) |
- |
1000 |
|
- |
| 15.1 d) i) (Phyaical tests for insulation : Elongation) |
- |
1000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation ) |
- |
3000 |
|
- |
| 15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation ) |
- |
3000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Hot set ) |
- |
1000 |
|
- |
| 15.1 d) iii) (Phyaical tests for insulation : Permanent set ) |
- |
1000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 d) v) (Insulation: Waterabsorption(gravimetric)) |
- |
3000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Tensile stregth) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation ) |
- |
3000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation ) |
- |
3000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation ) |
- |
3000 |
|
- |
| 15.1 e) iii) (Sheath: Loss of mass in air oven) |
- |
3000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage ) |
- |
1000 |
|
- |
| 15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed ) |
- |
1000 |
|
- |
| 15.1 e) v) (Sheath : Hot deformation) |
- |
1000 |
|
- |
| 15.1 e) vi) (Sheath : Heat shock test) |
- |
1000 |
|
- |
| 15.1 e) vii) (Sheath : Thermalstability) |
- |
1000 |
|
- |
| 15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity ) |
- |
1000 |
|
- |
| 16.2(HIGH VOLTAGE TEST ) |
- |
1000 |
|
- |
| 16.3(FLAMMABILITY TEST : Period of Burning ) |
- |
1000 |
|
- |
| 16.3(FLAMMABILITY TEST : Unaffected length ) |
- |
1000 |
|
- |
| 16.9(Oxygen Index Test) |
- |
3000 |
|
- |
| 16.1(Flame Retardance Test on Single Cables) |
- |
3000 |
|
- |
| 16.11(Flame Retardance Test on Bunched Cables) |
- |
5000 |
|
- |
| 16.13(Test for Halogen Acid Gas Evolution) |
- |
3000 |
|
- |
| 16.14(Temperature Index) |
- |
3000 |
|
- |
| 17.1(Manufacturer'. identification) |
- |
500 |
|
- |
| 17.2(cable Indentification ) |
- |
500 |
|
- |
| 17.3(cable Code ) |
- |
500 |
|
- |
| 15.4 (a)(Cold bend) |
- |
1000 |
|
- |
| 15.4 (b)(Cold impact) |
- |
1000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
3000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
3000 |
|
- |
| Table 1(Ageing in air oven - Elongation on Insulation) |
- |
3000 |
|
- |
| Table 1(Ageing in air oven - Tensile strength on Insulation) |
- |
3000 |
|
- |
| Table 4(Copper purity test) |
- |
5000 |
|
- |
| Cl No. 16.15(Smoke density test) |
- |
2000 |
|
- |
| Table 2(Cold Impact test for Outer sheath) |
- |
1000 |
|
- |
| Table 2(Cold bend test for Outer sheath) |
- |
1000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl 16(Halogen Acid Gas Test) |
- |
3000 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.8(Conductor) |
- |
500 |
|
- |
| Cl.15.4(Cold Bend Test (for outer sheath)) |
- |
1000 |
|
- |
| Cl.15.4(Cold Impact Test (For outer sheath)) |
- |
1000 |
|
- |
| Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables)) |
- |
1000 |
|
- |
| 15.1 e) i) (Physical tests for outer sheath : Elongation) |
- |
1000 |
|
- |
| 15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth ) |
- |
3000 |
|
- |
|
- |
-
Included w.e.f.23.06.2025 |
| 5149 |
DELHI TEST HOUSE (50) KUNDLI SONIPAT
| 9127026
| IS 16270 (2023) |
Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test |
-- |
400000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl-4.1(Photovoltaic Energy System) |
- |
0 |
|
- |
| Cl-4.2(Secondary Cells and Batteries) |
- |
0 |
|
- |
| Cl-4.3(General Operating Conditions) |
- |
0 |
|
- |
| Cl-4.3.8(Storage) |
- |
0 |
|
- |
| Cl-4.3.9(Operating Temperature) |
- |
0 |
|
- |
| Cl-5.1(Mechanical Endurance) |
- |
0 |
|
- |
| Cl-5.2(Charge Efficiency) |
- |
0 |
|
- |
| Cl-5.3(Deep Discharge Protection) |
- |
0 |
|
- |
| Cl-5.4(Marking) |
- |
1500 |
|
- |
| Cl-5.5(Safety) |
- |
0 |
|
- |
| Cl-5.6(Documentation) |
- |
0 |
|
- |
| Cl-6(Functional characteristice) |
- |
0 |
|
- |
| Cl-7(General test conditions) |
- |
0 |
|
- |
| Cl-8.1(Capacity Test) |
- |
50000 |
|
- |
| Cl-8.2(Endurance Test) |
- |
80000 |
|
- |
| Cl-8.3(Charge Retention Test) |
- |
70000 |
|
- |
| Cl-8.4(Cycle Endurance in Photovoltaic Application (Extreme Conditions)) |
- |
140000 |
|
- |
| Cl-8.5(Sulphation Test (Applicable for Lead Acid Batteries only)) |
- |
28500 |
|
- |
| Cl-8.6(Water Loss Test (Valid for Flooded Lead Acid Batteries only)) |
- |
30000 |
|
- |
| Cl-9.1(Type Tests) |
- |
0 |
|
- |
| Cl-9.2(Acceptance Test) |
- |
0 |
|
- |
| 4.3.7.1(Specific gravity) |
- |
0 |
|
- |
| Cl-4.1(Photovoltaic Energy System) |
- |
0 |
|
- |
| Cl-4.2(Secondary Cells and Batteries) |
- |
0 |
|
- |
| Cl-4.3(General Operating Conditions) |
- |
0 |
|
- |
| Cl-4.3.8(Storage) |
- |
0 |
|
- |
| Cl-4.3.9(Operating Temperature) |
- |
0 |
|
- |
| Cl-5.1(Mechanical Endurance) |
- |
0 |
|
- |
| Cl-5.2(Charge Efficiency) |
- |
0 |
|
- |
| Cl-5.3(Deep Discharge Protection) |
- |
0 |
|
- |
| Cl-5.4(Marking) |
- |
1500 |
|
- |
| Cl-5.5(Safety) |
- |
0 |
|
- |
| Cl-5.6(Documentation) |
- |
0 |
|
- |
| Cl-6(Functional characteristice) |
- |
0 |
|
- |
| Cl-7(General test conditions) |
- |
0 |
|
- |
| Cl-8.1(Capacity Test) |
- |
50000 |
|
- |
| Cl-8.2(Endurance Test) |
- |
80000 |
|
- |
| Cl-8.3(Charge Retention Test) |
- |
70000 |
|
- |
| Cl-8.4(Cycle Endurance in Photovoltaic Application (Extreme Conditions)) |
- |
140000 |
|
- |
| Cl-8.5(Sulphation Test (Applicable for Lead Acid Batteries only)) |
- |
28500 |
|
- |
| Cl-8.6(Water Loss Test (Valid for Flooded Lead Acid Batteries only)) |
- |
30000 |
|
- |
| Cl-9.1(Type Tests) |
- |
0 |
|
- |
| Cl-9.2(Acceptance Test) |
- |
0 |
|
- |
| 4.3.7.1(Specific gravity) |
- |
0 |
|
- |
|
23 Jun, 2028 |
-
Included w.e.f.26.06.2025 |
| 5150 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 15869 (2020) |
Textiles – Open weave coir Bhoovastra – Specification (first revision) |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Clause 5, Table 1, (i) (Mass per unit area, g/m2, Min) |
- |
|
|
|
| Clause 5, Table 1, (ii) (Width, cm, Min) |
- |
|
|
|
| Clause 5, Table 1, (iii) (Length, m) |
- |
|
|
|
| Clause 5, Table 1, (iv) (Thickness at 20 kPa, mm, Min) |
- |
|
|
|
| Clause 5, Table 1, (v) (Runnage, m/kg) |
- |
|
|
|
| Clause 5, Table 1, (vi) (Break load, dry (kN/m), Min) |
- |
|
|
|
| Clause 5, Table 1, (vii) (Break load, wet (kN/m), Min) |
- |
|
|
|
| Clause 5, Table 1, (viii) (Peak load, dry (kN/m), Min) |
- |
|
|
|
| Clause 5, Table 1, (ix) (Peak load, wet (kN/m), Min) |
- |
|
|
|
| Clause 5, Table 1, (x) (Trapezoidal Tearing Strength at 25 mm Gauge Length) |
- |
|
|
|
| Clause 5, Table 1, (xi) (Mesh size, mm, Min) |
- |
|
|
|
|
- |
-
Except raw material |
| 5151 |
Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar
| 9138706
| IS 14246 (2024) |
CONTINUOUSLY PRE-PAINTED GALVANIZED STEEL SHEETS AND STRIPS - SPECIFICATION Second Revision |
Class 1,2,3 & 4 |
37100 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl-4.1(Steel Base) |
- |
3500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-4.2(Metallic Coating) |
- |
2000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-4.3(Organic Coating) |
- |
1500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-4.4(Dry Film Thickness) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-4.5(Profiles) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-5(Classification of durability of organic coating) |
- |
0 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-6.1(Sampling of Test Specimen) |
- |
0 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-6.2.3(Bend Test) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-6.3.1(Pencil Hardness Test) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-6.4(Impact Resistance Test) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-6.5(Cross Hatch Test) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-6.6(Solvent Resistance Test) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-6.7(Other Tests) |
- |
0 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-7.3.1(Gloss) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-7.3.2(Colour) |
- |
1000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-8.1, Table-4 (i)(Undercut at scribed lines) |
- |
10000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-8.1, Table-4 (ii)(Corrosion of the base metal) |
- |
0 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-8.1, Table-4 (iii)(Blistering) |
- |
0 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-8.2 Table 5 (i)(Undercut at scribed lines) |
- |
10000 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-8.2 Table 5 (ii)(Blistering) |
- |
0 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-9.1(The nominal thickness of sheets) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-9.2(The case of strips) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-9.3(Mass of each pack) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-9.4.1(Tolerances on thickness sheets and strips) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-9.4.2(Width) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-9.4.3(Length) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-9.4.4(Mass) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-10.1(Camber) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-10.2(Deviation from Squareness (Out-of Square) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-10.3(Deviation from Flatness) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| Cl-14(Marking) |
- |
100 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Carbon) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Sulphur) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Phosphorus) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Manganese) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Nitrogen) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Silicon) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Aluminium) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Vanadium) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Niobium) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Copper) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Titanium) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
| As per Cl.4.1(Boron) |
- |
500 |
|
Rs.30000/- for Class-1,Rs.35000/- for Class-2,Rs.45000/- for Class-3,Rs.60000/- for Class-4 |
|
31 Dec, 2026 |
-
Included w.e.f.22.05.2025 |
| 5152 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 18482 (2023) |
Textiles - Sandwich extrusion laminated polypropylene PP woven sacks for packaging bulk commodities - Specification |
- |
- View breakup
Mechanical testing charges for the products: Rs 7650/-
Chemical testing charges for the products: Rs. 1300/-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4 (Sack Type) |
- |
|
|
|
| 5.2.1 (Fabric) |
- |
|
|
|
| 5.2.2 (Linear density of tapes) |
- |
|
|
|
| 5.2.4 (Unlaminated fabric mass) |
- |
|
|
|
| 5.3.1.1.1 (Mass of BOPP film in sandwich extrusion lamination) |
- |
|
|
|
| 5.3.1.2.1 (Mass of nonwoven fabric in sandwich extrusion lamination) |
- |
|
|
|
| 5.4.1 (Sack) |
- |
|
|
|
| 6.1.1, Table 1 (Inside length) |
- |
|
|
|
| 6.1.1, Table 1 (Inside width) |
- |
|
|
|
| 6.1.1, Table 1 (Gusset width) |
- |
|
|
|
| 6.1.1, Table 1 (Warp per dm) |
- |
|
|
|
| 6.1.1, Table 1 (Weft per dm) |
- |
|
|
|
| 6.1.1, Table 1 (Mass of laminated fabric) |
- |
|
|
|
| 6.2, Table 1 (Average breaking strength - Lengthwise) |
- |
|
|
|
| 6.2, Table 1 (Average breaking strength - Widthwise) |
- |
|
|
|
| 6.2, Table 1 (Breaking strength of bottom seam) |
- |
|
|
|
| 6.2, Table 1 (Breaking strength of centre seam) |
- |
|
|
|
| 6.2, Table 1 (Average elongation at break of fabric - Lengthwise) |
- |
|
|
|
| 6.2, Table 1 (Average elongation at break of fabric - Widthwise) |
- |
|
|
|
| 6.3 (Average breaking strength - Lengthwise after UV exposure) |
- |
|
|
|
| 6.3 (Average breaking strength - Widthwise after UV exposure) |
- |
|
|
|
| Clause 5.4.5.3 ("Free from pin holes (except
for air removal perforations), patches, tears, blisters,
and any other visible defects") |
- |
|
|
|
| Clause 6.5 Table 1 viii (Ash content) |
- |
|
|
|
| Clause 5.4.5.3 ("Free from pin holes (except
for air removal perforations), patches, tears, blisters,
and any other visible defects") |
- |
|
|
|
|
- |
-
Except raw material |
| 5153 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 16709 (2017) |
Textiles - Polypropylene (PP) woven, laminated, block bottom valve sacks for packaging of 50 kg cement - Specification |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.1.1 (Sack Length) |
- |
|
|
|
| 4.1.2 (Sack Width) |
- |
|
|
|
| 4.1.3 (Top Closure Width and Bottom Closure Width) |
- |
|
|
|
| 4.1.4 (Patch Length) |
- |
|
|
|
| 4.1.5 (Patch Height) |
- |
|
|
|
| 4.1.6 (Length of Valve) |
- |
|
|
|
| 4.1.7 (Width of Valve Sleeve) |
- |
|
|
|
| 4.1.8 (Length of Valve Sleeve) |
- |
|
|
|
| 5.2 (Fabric) |
- |
|
|
|
| 5.2 (Tape density and width) |
- |
|
|
|
| 5.4 (Lamination for PP) |
- |
|
|
|
| 6.1 (Mass of Bale) |
- |
|
|
|
| 6.2.1 (Breaking Strength and Elongation at Break of Fabric) |
- |
|
|
|
| 6.2.2 (Weld Strength of Top and Bottom Closures) |
- |
|
|
|
| 6.3 (Drop Impact Testing of Filled Sacks) |
- |
|
|
|
| 6.4 (Ash Content) |
- |
|
|
|
| Cl-5.6 (Capacity) |
- |
|
|
|
| Cl- 6.6, Table.-1 (ii) (Ends per dm) |
- |
|
|
|
| Cl-6.6, Table-1 (iii) (Picks per dm) |
- |
|
|
|
| Cl.6.6, Table-1 (vii) (Elongation at break of fabric) |
- |
|
|
|
|
- |
-
Except raw material, Air Permeability |
| 5154 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 15138 (2024) |
Textiles - Jute Bags For Packing 50 Kg Sugar - Specification (second revision) |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| As per Clause 4.1 (Febric) |
- |
|
|
|
| As per Clause 4.1.1 (Febric) |
- |
|
|
|
| As per Clause 4.2 (Seam) |
- |
|
|
|
| As per Clause 4.3 (Hemming at the mouth) |
- |
|
|
|
| As per Clause 4.4 (Freedom from defects) |
- |
|
|
|
| As per Clause 5,5.1,5.2(Table 1) (i). Dimension,(a.-outside length) (b.-outside width)) |
- |
|
|
|
| As per Clause 5,5.1,5.2(Table 1) (ii). Ends/dm) |
- |
|
|
|
| As per Clause 5,5.1,5.2(Table 1) (iii). Picks/dm) |
- |
|
|
|
| As per Clause 5,5.1,5.2(Table 1) (iv). Corrected mass per bags) |
- |
|
|
|
| As per Clause 5,5.1,5.2(Table 1) (v). Average breaking load of sacking(a) warpway (b)weftway) |
- |
|
|
|
| As per Clause 5,5.1,5.2(Table 1) (vi). Average breaking load of seam(a) warpway (b)weftway) |
- |
|
|
|
| As per Clause 5,5.1,5.2(Table 1) (vii).Moisture regain) |
- |
|
|
|
| As per Clause 5,5.1,5.2(Table 1) (viii).oil content) |
- |
|
|
|
|
- |
-
Except raw material |
| 5155 |
EKO PRO ENGINEERS PVT LTD
| 8188216
| IS 3614 (2021) |
Specification of Fire Doors and Assembly First Revision of IS 3614 Parts 1 2 |
- |
265000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4(Integrity, Insulation) |
- |
265000 |
|
- |
| Cl 7.2.2(SIZE (width)) |
- |
265000 |
|
- |
| Cl 7.2.2(SIZE (Height)) |
- |
265000 |
|
- |
| Cl 7.3.2(SIZE (width)) |
- |
265000 |
|
- |
| Cl 7.3.2(SIZE (Height)) |
- |
265000 |
|
- |
| Cl 7.4.2(SIZE (width)) |
- |
265000 |
|
- |
| Cl 7.4.2(SIZE (Height)) |
- |
265000 |
|
- |
| Cl 7.5.2(SIZE (width)) |
- |
265000 |
|
- |
| Cl 7.5.2(SIZE (Height)) |
- |
265000 |
|
- |
| 7.3.1(MOISTURE CONTENT) |
- |
265000 |
|
- |
| 7.2.7(Vision Pane (Uninsulated door) Width) |
- |
265000 |
|
- |
| 7.2.7(Vision Pane (Uninsulated door) Height) |
- |
265000 |
|
- |
| 7.2.7(Vision Pane (Insulated door) Width) |
- |
265000 |
|
- |
| 7.2.7(Vision Pane (Insulated door) Height) |
- |
265000 |
|
- |
| 7.3.4(Vision Pane (Width)) |
- |
265000 |
|
- |
| 7.3.4(Vision Pane (Height)) |
- |
265000 |
|
- |
| Cl-7.2.1(Material) |
- |
265000 |
|
- |
| Cl-7.2.4(Fire Door Frames) |
- |
265000 |
|
- |
| Cl-7.2.5(Door Leaf) |
- |
265000 |
|
- |
| Cl-7.2.8(Louvres) |
- |
265000 |
|
- |
| Cl-7.2.9(Builder’s Hardware) |
- |
265000 |
|
- |
| Cl-7.4.3(Construction) |
- |
265000 |
|
- |
| Cl-7.4.5(Operator) |
- |
265000 |
|
- |
| Cl-7.5.1(Material) |
- |
265000 |
|
- |
| Cl-7.5.3(Construction of Sliding Door Leaf) |
- |
265000 |
|
- |
| Cl-11.3.1(Walls) |
- |
265000 |
|
- |
| Cl-11.4.1(Closing Devices) |
- |
265000 |
|
- |
| Cl-11.4.2(Releasing Devices) |
- |
265000 |
|
- |
| Cl-11.4.3(Hardware) |
- |
265000 |
|
- |
| Cl-6(VISION PANE ON FIRE DOORS) |
- |
265000 |
|
- |
| Cl-7.2.3(Construction) |
- |
265000 |
|
- |
| Cl-7.2.6(Intumescent Seal) |
- |
265000 |
|
- |
| Cl-7.3.6(Builder’s Hardware) |
- |
265000 |
|
- |
| Cl-7.4.4(General Requirement of Fire Rated Rolling
Shutter) |
- |
265000 |
|
- |
| Cl-7.5.4(General Requirement of Fire Rated Sliding Door) |
- |
265000 |
|
- |
| Cl-7.6(General Requirement of Fire Doors) |
- |
265000 |
|
- |
| Cl-7.3.3(Construction) |
- |
265000 |
|
- |
| Cl-7.4(Avg closing speed of fire rated rolling shutters) |
- |
265000 |
|
- |
|
19 Sep, 2028 |
-
Fire rated hinged door (metallic)-
FD 30 UD, FD 60 UD, FD 90 UD, FD 120 UD, FD 180 UD
FD 30 PI, FD 60 PI, FD 90 PI, FD 120 PI, FD 180 PI
FD 30 ID, FD 60 ID, FD 90 ID, FD 120 ID, FD 180 ID
Fire rated hinged door (wooden composite)-
FD 30 UD, FD 60 UD, FD 90 UD, FD 120 UD, FD 180 UD
FD 30 PI, FD 60 PI, FD 90 PI, FD 120 PI, FD 180 PI
FD 30 ID, FD 60 ID, FD 90 ID, FD 120 ID, FD 180 ID
Fire rated sliding doors (metallic)-
FD 30 UD, FD 60 UD, FD 90 UD, FD 120 UD, FD 180 UD
FD 30 PI, FD 60 PI, FD 90 PI, FD 120 PI, FD 180 PI
FD 30 ID, FD 60 ID, FD 90 ID, FD 120 ID, FD 180 ID
Fire rated rolling shutter (metallic)-
FD 120 UD, 180 UD, FD 240 UD, FD 120 PI, FD 180 PI, FD 240 PI, FD 120 ID, FD 180 ID, FD 240 ID |
| 5156 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 7903 (2017) |
Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision) |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3.4 ( Line/ Cord beading
IS 7903) |
- |
|
|
|
| 4.0 (Types IS 7903) |
- |
|
|
|
| 5.1.1 (Lamination IS 7903) |
- |
|
|
|
| 5.1.2 (Lamination IS 7903) |
- |
|
|
|
| 5.2.1 (Construction IS 7903) |
- |
|
|
|
| 5.2.1 (Construction IS 7903) |
- |
|
|
|
| 5.2.1 (Construction IS 7903) |
- |
|
|
|
| 5.2.1 (Construction IS 7903) |
- |
|
|
|
| 5.2.1 (Construction IS 7903) |
- |
|
|
|
| 5.2.1 (Construction IS 7903) |
- |
|
|
|
| 5.2.1 (Construction IS 7903) |
- |
|
|
|
| 5.3 (Joint/Seam, IS 7903) |
- |
|
|
|
| 6.1 Table 1,i) (No of HDPE fabric layers ,IS 7903) |
- |
|
|
|
| 6.1 Table 1,ii) (No of lamination layers, IS 7903) |
- |
|
|
|
| 6.1 Table 1, iii) (Total no of layers in the finished tarpaulin, IS 7903) |
- |
|
|
|
| 6.1 Table 1,iv) (Mass of finished tarpaulin, Annex B ,IS 7903) |
- |
|
|
|
| 6.1 Table 1,v) (Mass of laminated fabric, Annex C , IS 7903) |
- |
|
|
|
| 6.1 Table 1vi) (Breaking strength before UV exposure,warp ,IS 1969 Part 1) |
- |
|
|
|
| 6.1 Table 1vi) (Breaking strength before UV exposure,weft, IS 1969 part 1) |
- |
|
|
|
| 6.1 Table 1 vii) (Elongation at break of fabric,warp, IS 1969 Part 1) |
- |
|
|
|
| 6.1 Table 1 vii) (Elongation at break of fabric,weft, IS 1969 Part1) |
- |
|
|
|
| 6.1 Table 1 ix) (Welded seam strength before UV exposure (Weft) , IS 1969 Part 1) |
- |
|
|
|
| 6.1 Table 1 xi) (Trapezoidal tear strength, IS 14293) |
- |
|
|
|
| 6.1 Table 1 xii) (Puncture Resistance, Annex D of IS 7903) |
- |
|
|
|
| 6.1 Table 1 xiii) (Impact Failure load , at 1524 mmdrop, Annex E of IS 7903) |
- |
|
|
|
| 6.1 Table 1 xv) (Ash Content, Annex F of IS 7903) |
- |
|
|
|
| 6.2 (Length, IS 7903) |
- |
|
|
|
| 6.2 (Width, IS 7903) |
- |
|
|
|
| 6.2 (height, IS 7903) |
- |
|
|
|
|
- |
-
Except raw material, Retention of breaking strength after UV exposure of 144 h, Colour fastness to light and Water Proofness |
| 5157 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 14715 : Part 2 (2016) |
Jute geotextiles Part 2 Control of bank erosion in rivers and waterways – Specification (second revision) |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 1 (Thickness at 2 kPa- IS 13162 (Part 3)) |
- |
|
|
|
| 2 (Width- IS 1954) |
- |
|
|
|
| 2 (Mass- IS 15891 (Part 1)) |
- |
|
|
|
| 2 (Tensile strength MD*CD- IS 15891 (Part 3)) |
- |
|
|
|
| 1 (Elongation at break in MD × CD- IS 13162 (Part 5)) |
- |
|
|
|
| 1 (Ends × Picks- IS 1963) |
- |
|
|
|
| 1 (Puncture resistance- IS 16078) |
- |
|
|
|
| 1 (Permittivity at 50 mm constant head- IS 14324) |
- |
|
|
|
| 1 (Apparent opening size (A. O. S.) , O95- IS 14294) |
- |
|
|
|
| 4, Table 1, (ii) (Construction) |
- |
|
|
|
| 5 (Sampling) |
- |
|
|
|
| 6 (Packaging) |
- |
|
|
|
|
- |
-
Except raw material and Burst strength. |
| 5158 |
BIS, Hyderabad Branch Laboratory (HYBL)
| None
| IS 14715 : Part 1 (2016) |
Jute geotextiles Part 1 Strengthening of sub-grade in roads – Specification (second revision) |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 1 (Weight at 20% moisture Regain- IS 14716) |
- |
|
|
|
| 1 (Width- IS 1954) |
- |
|
|
|
| 1 (Ends × Picks- IS 1963) |
- |
|
|
|
| 1 (Tensile strength in MD × CD- IS 13162 (Part 5)) |
- |
|
|
|
| 1 ("Elongation at break in MD × CD-
IS 13162 (Part 5)") |
- |
|
|
|
| 1 (Puncture resistance- IS 16078) |
- |
|
|
|
| 2 (Apparent opening size (A. O. S.), O95- IS 14294) |
- |
|
|
|
| 4, Table 1, (v) (Thickness at 2kPA, mm, for Woven Jute Geotextiles) |
- |
|
|
|
| 4, Table 2, (ii) (Mass, g/m2, for Non-Woven Jute Geotextiles) |
- |
|
|
|
| 4, Table 1, (i) (Construction) |
- |
|
|
|
| 5 (Sampling) |
- |
|
|
|
| 6 (Packaging) |
- |
|
|
|
|
- |
-
Except raw material and Burst strength. |
| 5159 |
Gravitas Laboratories Private Limited, Greater Noida
| 8182606
| IS 21 (1992) |
Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision) |
- |
7500 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, WP')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, WP')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, WP')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, WP')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, WP')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, WP')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, WP')(0.2 Percent Proof Stress) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'W')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'W')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'W')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'W')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'W')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'W')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'W')(0.2 Percent Proof Stress) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'O')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 64430, 'O')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(0.2 Percent Proof Stress) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(0.2 Percent Proof Stress) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(0.2 Percent Proof Stress) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(0.2 Percent Proof Stress) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(0.2 Percent Proof Stress) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(0.2 Percent Proof Stress) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'O')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 40800, 'O')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'O')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31500, 'O')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'O')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 31000, 'O')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'O')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'O')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'O')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19500, 'O')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'O')(Bend Test (Radius of Bend)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
500 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19000, 'O')(Tensile Strength) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Chromium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Titanium and or other grain refining elements) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Magnesium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Copper) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Chromium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Iron) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Magnesium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-B)(Copper) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Chromium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Iron) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Magnesium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 51000-A)(Copper) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Titanium and or other grain refining elements) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Iron) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Magnesium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 40800)(Copper) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Titanium and or other grain refining elements) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Iron) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Magnesium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31500)(Copper) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Chromium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Titanium and or other grain refining elements) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Iron) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Magnesium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 31000)(Copper) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19600)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19600)(Cu+Si+Fe+Mn+Zn) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19600)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19600)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19600)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19600)(Iron) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19600)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19600)(Copper) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19500)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19500)(Cu+Si+Fe+Mn+Zn) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19500)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19500)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19500)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19500)(Iron) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19500)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19500)(Copper) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Lead) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Aluminium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Zinc) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Manganese) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Iron) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Silicon) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Magnesium) |
- |
500 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 19000)(Copper) |
- |
500 |
|
- |
| 4.1, & 4.1.1(Lead) |
- |
600 |
|
- |
| 4.1.2(Aluminium) |
- |
600 |
|
- |
| 4.2,
Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm)) |
- |
600 |
|
- |
| 4.2,
Table 1of IS:21 (Designation 64430)(Iron) |
- |
600 |
|
- |
|
- |
-
Included w.e.f 19.05.2025 |
| 5160 |
Global Scientific Solution (P) Ltd.
| 8189526
| IS 374 (2019) |
Specification for electric ceiling type fans and regulators (Third Revision) |
- |
18000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7(Classification (as per Cl.6 of IS 302-2-80 :2017)) |
- |
500 |
|
- |
| 7(Classification (as per Cl.6 of IS 302-2-80 :2017)) |
- |
500 |
|
- |
| 7(Classification (as per Cl.6 of IS 302-2-80 :2017)) |
- |
500 |
|
- |
| 7(Classification (as per Cl.6 of IS 302-2-80 :2017)) |
- |
500 |
|
- |
| 8.1(Marking (as per Cl. 7 of IS 302-2-80:2017)) |
- |
1000 |
|
- |
| 8.1,a(Marking ) |
- |
1000 |
|
- |
| 8.1,b(Marking ) |
- |
1000 |
|
- |
| 8.1,c(Marking ) |
- |
1000 |
|
- |
| 8.1,d(Marking ) |
- |
1000 |
|
- |
| 8.1,e(Marking ) |
- |
1000 |
|
- |
| 8.1,f(Marking ) |
- |
1000 |
|
- |
| 8.1,g(Marking ) |
- |
1000 |
|
- |
| 8.2(Marking ) |
- |
1000 |
|
- |
| 8.3,a(Marking ) |
- |
1000 |
|
- |
| 8.3,b(Marking ) |
- |
1000 |
|
- |
| 8.3,c(Marking ) |
- |
1000 |
|
- |
| 8.3,d(Marking ) |
- |
1000 |
|
- |
| 8.3,e(Marking ) |
- |
1000 |
|
- |
| 8.4(Marking ) |
- |
1000 |
|
- |
| 8(Marking (as per Cl. 7.1 of IS 302-2-80:2017)) |
- |
1000 |
|
- |
| 8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008)) |
- |
1000 |
|
- |
| 8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008)) |
- |
1000 |
|
- |
| 8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017)) |
- |
1000 |
|
- |
| 6.2(Rating) |
- |
500 |
|
- |
| 9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Heating (as per Cl.11 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Heating (as per Cl.11 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Heating (as per Cl.11 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Heating (as per Cl.11 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017)) |
- |
2000 |
|
- |
| 9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017)) |
- |
2000 |
|
- |
| 9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) ) |
- |
2000 |
|
- |
| 9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) ) |
- |
2000 |
|
- |
| 9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Construction (as per Cl.22.101 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008)) |
- |
1000 |
|
- |
| 9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008)) |
- |
1000 |
|
- |
| 9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008)) |
- |
1000 |
|
- |
| 9(Components (as per Cl.24.103 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Components (as per Cl.24.104 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017)) |
- |
2000 |
|
- |
| 9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 10.1(Speed Regulators) |
- |
1000 |
|
- |
| 10.2(Speed Regulators) |
- |
1000 |
|
- |
| 10.2(Speed Regulators) |
- |
1000 |
|
- |
| 10.2(Speed Regulators) |
- |
1000 |
|
- |
| 10.3(Speed Regulators) |
- |
1000 |
|
- |
| 10.4(Speed Regulators) |
- |
1000 |
|
- |
| 10.5(Speed Regulators) |
- |
1000 |
|
- |
| 10.6(Speed Regulators) |
- |
1000 |
|
- |
| 10.7(Speed Regulators) |
- |
1000 |
|
- |
| 10.7(Speed Regulators) |
- |
1000 |
|
- |
| 10.8(Speed Regulators) |
- |
1000 |
|
- |
| 11.1(Starting) |
- |
1000 |
|
- |
| 11.2(Starting) |
- |
1000 |
|
- |
| 12(Interchangeability) |
- |
1000 |
|
- |
| 13(Silent Operation) |
- |
1000 |
|
- |
| 14.3 & Table 1(Test for Air Performance) |
- |
2000 |
|
- |
| 14.3 & Table 1(Test for Air Performance) |
- |
2000 |
|
- |
| 14.4(Measurement of Speed of the Fan ) |
- |
1000 |
|
- |
| 14.5(Measurement of Power factor and Power Input) |
- |
1000 |
|
- |
| 14.5(Measurement of Power factor and Power Input) |
- |
1000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 17(Test for Harmonic Distortion) |
- |
1000 |
|
- |
| 7(Classification (as per Cl.6 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 7(Classification (as per Cl.6 of IS 302-2-80 :2017)) |
- |
500 |
|
- |
| 7(Classification (as per Cl.6 of IS 302-2-80 :2017)) |
- |
500 |
|
- |
| 7(Classification (as per Cl.6 of IS 302-2-80 :2017)) |
- |
500 |
|
- |
| 8.1(Marking (as per Cl. 7 of IS 302-2-80:2017)) |
- |
1000 |
|
- |
| 8.1,a(Marking ) |
- |
1000 |
|
- |
| 8.1,b(Marking ) |
- |
1000 |
|
- |
| 8.1,c(Marking ) |
- |
1000 |
|
- |
| 8.1,d(Marking ) |
- |
1000 |
|
- |
| 8.1,e(Marking ) |
- |
1000 |
|
- |
| 8.1,f(Marking ) |
- |
1000 |
|
- |
| 8.1,g(Marking ) |
- |
1000 |
|
- |
| 8.2(Marking ) |
- |
1000 |
|
- |
| 8.3(Marking ) |
- |
1000 |
|
- |
| 8.3,a(Marking ) |
- |
1000 |
|
- |
| 8.3,b(Marking ) |
- |
1000 |
|
- |
| 8.3,c(Marking ) |
- |
1000 |
|
- |
| 8.3,d(Marking ) |
- |
1000 |
|
- |
| 8.3,e(Marking ) |
- |
1000 |
|
- |
| 8.4(Marking ) |
- |
1000 |
|
- |
| 8(Marking (as per Cl. 7.1 of IS 302-2-80:2017)) |
- |
1000 |
|
- |
| 8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008)) |
- |
1000 |
|
- |
| 8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008)) |
- |
1000 |
|
- |
| 8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017)) |
- |
1000 |
|
- |
| 6.2(Rating) |
- |
1000 |
|
- |
| 9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Heating (as per Cl.11 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Heating (as per Cl.11 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Heating (as per Cl.11 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Heating (as per Cl.11 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017)) |
- |
2000 |
|
- |
| 9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017)) |
- |
2000 |
|
- |
| 9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) ) |
- |
2000 |
|
- |
| 9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) ) |
- |
2000 |
|
- |
| 9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-1:2008)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-1:2008)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Construction (as per Cl.22.101 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008)) |
- |
1000 |
|
- |
| 9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008)) |
- |
1000 |
|
- |
| 9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008)) |
- |
1000 |
|
- |
| 9(Components (as per Cl.24.103 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Components (as per Cl.24.104 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017)) |
- |
2000 |
|
- |
| 9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017)) |
- |
1000 |
|
- |
| 10.1(Speed Regulators) |
- |
1000 |
|
- |
| 10.2(Speed Regulators) |
- |
1000 |
|
- |
| 10.2(Speed Regulators) |
- |
1000 |
|
- |
| 10.2(Speed Regulators) |
- |
1000 |
|
- |
| 10.3(Speed Regulators) |
- |
1000 |
|
- |
| 10.4(Speed Regulators) |
- |
1000 |
|
- |
| 10.5(Speed Regulators) |
- |
1000 |
|
- |
| 10.6(Speed Regulators) |
- |
1000 |
|
- |
| 10.7(Speed Regulators) |
- |
1000 |
|
- |
| 10.7(Speed Regulators) |
- |
1000 |
|
- |
| 10.8(Speed Regulators) |
- |
1000 |
|
- |
| 11.1(Starting) |
- |
1000 |
|
- |
| 11.2(Starting) |
- |
1000 |
|
- |
| 12(Interchangeability) |
- |
1000 |
|
- |
| 13(Silent Operation) |
- |
1000 |
|
- |
| 14.3 & Table 1(Test for Air Performance) |
- |
2000 |
|
- |
| 14.3 & Table 1(Test for Air Performance) |
- |
2000 |
|
- |
| 14.4(Measurement of Speed of the Fan ) |
- |
1000 |
|
- |
| 14.4(Measurement of Speed of the Fan ) |
- |
1000 |
|
- |
| 14.5(Measurement of Power factor and Power Input) |
- |
1000 |
|
- |
| 14.5(Measurement of Power factor and Power Input) |
- |
1000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 16(Endurance Test) |
- |
2000 |
|
- |
| 17(Test for Harmonic Distortion) |
- |
1000 |
|
- |
| 4(GENERAL REQUIREMENTS) |
- |
1000 |
|
- |
| 5(GENERAL NOTES ON TESTS) |
- |
1000 |
|
- |
| 15.1, 15.2(Air delivery and service value) |
- |
2000 |
|
- |
| Cl-9 (Cl-19.11.4.1 of IS 302-1)(Electrostatic discharge) |
- |
0 |
|
- |
| Cl-9 (Cl-19.11.4.2 of IS 302-1)(Radiated Fields) |
- |
0 |
|
- |
| Cl-9 (Cl-19.11.4.3 of IS 302-1)(Fast transient bursts) |
- |
0 |
|
- |
| Cl-9 (Cl-19.11.4.4 of IS 302-1)(Surge Immunity test) |
- |
0 |
|
- |
| Cl-9 (Cl-19.11.4.5 of IS 302-1)(Immunity to conducted discharge) |
- |
0 |
|
- |
| Cl-9 (Cl-19.11.4.6 of IS 302-1)(Voltage dips and interruptions) |
- |
0 |
|
- |
| Cl-9 (Cl-19.11.4.7 of IS 302-1)(Harmonics) |
- |
0 |
|
- |
| Cl-9 (Cl-19.101 of IS 302-1)(Abnormal Operation) |
- |
1000 |
|
- |
| (Cl. 17 of IS 302-2-80 :2017)(Overload protection of transformers and associated circuits) |
- |
1000 |
|
- |
| (Cl.4.4 of IS 374: 2019)(Bearings) |
- |
1000 |
|
- |
| (Cl. 4.5 of IS 374: 2019)(Brushless DC Motor) |
- |
1000 |
|
- |
| (Cl.4.6 of IS 374: 2019)(Enclosure) |
- |
1000 |
|
- |
| (Cl. 7.6 of IS 302 Part 1)(Marking and Instructions) |
- |
1000 |
|
- |
| Cl. 7.8 of IS 302-2-80 :2017(MARKING AND INSTRUCTIONS) |
- |
1000 |
|
- |
| (Cl. 7.12 of IS 302-2-80 :2017)(Marking and Instructions) |
- |
1000 |
|
- |
| (Cl. 7.12.1 of IS 302-2-80 :2017)(Marking and Instructions) |
- |
1000 |
|
- |
| (Cl. 7.12.5 of IS 302-1: 2008)(Marking and Instructions) |
- |
1000 |
|
- |
| (Cl. 7.12.5 of IS 302-1: 2008)(Marking and Instructions) |
- |
1000 |
|
- |
| (Cl. 7.12.5 of IS 302-1: 2008)(Marking and Instructions) |
- |
1000 |
|
- |
| (Cl. 7.12.7 of IS 302-1: 2008(Marking and Instructions) |
- |
1000 |
|
- |
| (Cl. 7.13 of IS 302-1: 2008)(Marking and Instructions) |
- |
1000 |
|
- |
| (Cl. 7.14 of IS 302-1: 2008)(Marking and Instructions) |
- |
1000 |
|
- |
| (Cl. 10.1 of IS 374: 2019)(SPEED REGULATORS) |
- |
1000 |
|
- |
| (Cl. 10.3 of IS 374: 2019)(SPEED REGULATORS) |
- |
1000 |
|
- |
| (Cl. 10.4 of IS 374: 2019)(SPEED REGULATORS) |
- |
1000 |
|
- |
| (Cl. 10.7 of IS 374: 2019)(SPEED REGULATORS) |
- |
1000 |
|
- |
| (Cl. 10.7 of IS 374: 2019)(SPEED REGULATORS) |
- |
1000 |
|
- |
| (Cl. 10.8 of IS 374: 2019)(SPEED REGULATORS) |
- |
1000 |
|
- |
| (Cl. 11.2 of IS 374: 2019)(STARTING) |
- |
1000 |
|
- |
| (Cl. 13 of IS 374: 2019)(SILENT OPERATION) |
- |
1000 |
|
- |
| (Cl. 15.1 of IS 374: 2019)(PERFORMANCE REQUIREMENTS) |
- |
2000 |
|
- |
| (Cl. 15.1 of IS 374: 2019)(PERFORMANCE REQUIREMENTS) |
- |
2000 |
|
- |
| (Cl. 17 of IS 374: 2019(Test for Harmonic Distortion) |
- |
1000 |
|
- |
| (Cl. 8.2 of IS 302-1: 2008)(PROTECTION AGAINST ACCESS TO LIVE PARTS) |
- |
1000 |
|
- |
| (Cl. 11 of IS 302-1: 2008)(HEATING) |
- |
1000 |
|
- |
| (Cl. 15 of IS 302-1: 2008)(MOISTURE RESISTANCE) |
- |
2000 |
|
- |
| (Cl. 15 of IS 302-1: 2008)(MOISTURE RESISTANCE) |
- |
2000 |
|
- |
| (Cl. 15 of IS 302-1: 2008.(MOISTURE RESISTANCE) |
- |
2000 |
|
- |
| (Cl. 17 of IS 302-1: 2008)(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS) |
- |
1000 |
|
- |
| (Cl. 17 of IS 302-1: 2008)(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS) |
- |
1000 |
|
- |
| (Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION) |
- |
1000 |
|
- |
| (Cl. 19.7 of IS 302-1: 2008)(ABNORMAL OPERATION) |
- |
1000 |
|
- |
| (Cl. 19 of IS 302-2-80 :2017)(ABNORMAL OPERATION) |
- |
1000 |
|
- |
| (Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION) |
- |
1000 |
|
- |
| (Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION) |
- |
1000 |
|
- |
| (Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION) |
- |
1000 |
|
- |
| (Cl. 19.13 of IS 302-1: 2008)(ABNORMAL OPERATION) |
- |
1000 |
|
- |
| (Cl. 20.102 of IS 302-2-80 :2017)(STABILITY AND MECHANICAL HAZARDS) |
- |
1000 |
|
- |
| (Cl. 22.2 of IS 302-1: 2008)(CONSTRUCTION) |
- |
1000 |
|
- |
| (Cl. 22.14 of IS 302-1: 2008)(CONSTRUCTION) |
- |
1000 |
|
- |
| (Cl. 22.18 of IS 302-1: 2008)(Electric Ceiling type fan-Specification) |
- |
1000 |
|
- |
| (Cl. 22.21 of IS 302-1: 2008)(CONSTRUCTION) |
- |
1000 |
|
- |
| (Cl. 22.22 of IS 302-1: 2008)(CONSTRUCTION) |
- |
1000 |
|
- |
| (Cl. 22.41 of IS 302-1: 2008)(CONSTRUCTION) |
- |
1000 |
|
- |
| (Cl. 22.44 of IS 302-1: 2008)(CONSTRUCTION) |
- |
1000 |
|
- |
| (Cl. 22.101 of IS 302-2-80: 2017)(CONSTRUCTION) |
- |
1000 |
|
- |
| (Cl. 23.1 of IS 302-1: 2008)(INTERNAL WIRING) |
- |
1000 |
|
- |
| (Cl. 23.2 of IS 302-1: 2008)(INTERNAL WIRING) |
- |
1000 |
|
- |
| (Cl. 23.4 of IS 302-1: 2008)(INTERNAL WIRING) |
- |
1000 |
|
- |
| (Cl. 23.5 of IS 302-1: 2008)(INTERNAL WIRING) |
- |
1000 |
|
- |
| (Cl. 23.6 of IS 302-1: 2008)(INTERNAL WIRING) |
- |
1000 |
|
- |
| (Cl. 23.7 of IS 302-1: 2008)(INTERNAL WIRING) |
- |
1000 |
|
- |
| (Cl. 23.9 of IS 302-1: 2008)(INTERNAL WIRING) |
- |
1000 |
|
- |
| (Cl. 23.10 of IS 302-1: 2008)(INTERNAL WIRING) |
- |
1000 |
|
- |
| (Cl. 24.1 of IS 302-1: 2008)(COMPONENTS) |
- |
1000 |
|
- |
| (Cl. 24.5 of IS 302-1: 2008)(COMPONENTS) |
- |
1000 |
|
- |
| (Cl. 24.105 of IS IS 302-2-80 :2017)(COMPONENTS) |
- |
1000 |
|
- |
| (Cl. 26.1 of IS 302-1: 2008)(TERMINALS FOR EXTERNAL CONDUCTORS) |
- |
1000 |
|
- |
| (Cl. 26.8 of IS 302-1: 2008)(TERMINALS FOR EXTERNAL CONDUCTORS) |
- |
1000 |
|
- |
| (Cl. 26.9 of IS 302-1: 2008)(TERMINALS FOR EXTERNAL CONDUCTORS) |
- |
1000 |
|
- |
| (Cl. 26.10 of IS 302-1: 2008)(TERMINALS FOR EXTERNAL CONDUCTORS) |
- |
1000 |
|
- |
| (Cl. 27.1 of IS 302-1: 2008)(PROVISION FOR EARTHING) |
- |
1000 |
|
- |
| (Cl. 27.2 of IS 302-1: 2008)(PROVISION FOR EARTHING) |
- |
1000 |
|
- |
| (Cl. 27.4 of IS 302-1: 2008)(PROVISION FOR EARTHING) |
- |
1000 |
|
- |
| (Cl. 27.5 of IS 302-1: 2008)(PROVISION FOR EARTHING) |
- |
1000 |
|
- |
| (Cl. 28.4 of IS 302-1: 2008)(SCREWS AND CONNECTIONS) |
- |
1000 |
|
- |
| (Cl. 30.2 of IS 302-1: 2008)(RESISTANCE TO HEAT AND FIRE) |
- |
1000 |
|
- |
| (Cl. 30.2 of IS 302-1: 2008)(RESISTANCE TO HEAT AND FIRE) |
- |
1000 |
|
- |
| (Cl. 32 of IS 302-1: 2008)(Radiation, toxicity and similar hazards) |
- |
1000 |
|
- |
| 14.4(Measurement of Speed of the Fan ) |
- |
1000 |
|
- |
|
31 Oct, 2028 |
-
Cl. 19.11.4.1 to Cl. 19.11.4.7 (EMI/EMC), Cl. 24, Cl. 32.2, Cl. 15.1.1(IPX7-8), Cl 12 as per IS 302-2-80, Cl. 10.7 |
