BIS - LIMS (Laboratory Information Management System)

Search by IS Number

Reset

14026 Results

S.No.

Lab Name

Osl Code

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

12421

BIS, Eastern Regional Laboratory (ERL)

None

IS 903 (1993)

Specification for Fire Hose Delivery Couplings, Branch Pipe, Nozzles And Nozzle Spanner - Specificaion

Please see remarks View breakup
i) DELIVERY HOSE COUPLINGS (Sec-1) Rs3600/- + material ii) BRANCH PIPE (Sec-2) + Nozzle (Sec-3) Rs3000/- + material iii) NOZZLE SPANNER (Sec-4) Rs.1500/- + material

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Finish and workmanship)	-
5 (Delivery hose coupling)	-
5 (Delivery hose coupling)	-
5 (Delivery hose coupling)	-
5 (Delivery hose coupling)	-
5.3 (Size and Dimension )	-
5.3 (Size and Dimension )	-
5.3 (Size and Dimension )	-
5.3 (Size and Dimension )	-
3 (Finish and workmanship)	-
5.3 (Size and Dimension )	-

-
Facility not available for Hydraulic test & critical dimensions, Sn,Si,Mn,Al,Sb

12422

BIS, Eastern Regional Laboratory (ERL)

None

IS 6527 (1995)

Stainless steel wire rods - Specification (First Revision)

For all designation except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 9 (Tensile & Hardness)	-
Cl 10 (Diameter & Out Of Round)	-
Cl 10 (Diameter & Out Of Round)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Carbon)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Silicon)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Manganese)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Nickel)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Chromium)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Phosphorous)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Copper)	-
7, Table 1of IS:6527 (Designation X10Cr17Mn6Ni4) (Titanium)	-
7, Table 1of IS:6527 (Designation X04Cr13) (Aluminium)	-

-
Facility not available for S, Carbon less than 0.05%, Mn more than 5%, Al, Mo more than 1.5%, Ti & Nb Steel designation is required and hardness below 20 mm Dia and 0.4mm thickness

12423

BIS, Eastern Regional Laboratory (ERL)

None

IS 1322 (1993)

Bitumen Felts for Water Proofing and Damp-proofing

For all types except tests mentioned in the remarks

Rs.8300/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4 & Table 1 (Weight )	-
5.5 (Free from external defects - IS 1322)	-
6 (Dimension-IS 1322)	-
7.1 (Breaking Strength test- IS 13826(Part 1))	-
7.1 (Pliabilitry Test-IS 13826(Part 2))	-
7.1 (Strage Sticking Test-IS 13826(Part 3))	-
7.1 (Pressure Head Test-IS 13826(Part-4 )	-
7.1 (Heat Resistance Test-IS 13826(Part 5))	-
7.1 (Water Absorption Test-IS 13826(Part 6))	-
3.1.1 (Fibre Base)	-
3.1.2 (Hessian Base)	-
4.2.1 (Composition)	-
4.1.1 (Fibre base felt)	-

-
Complete

12424

BIS, Eastern Regional Laboratory (ERL)

None

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-
4.4 (Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-
4.4 (Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-
4.4 (Seam The stitching shall be done with double fold over seam to)	-
4.4 (The number of stitches/dm shall be 14 ± 2.)	-
5/5.1-Table 1-Sr. no. iv (Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-
5/5.1-Table 1-Sr. no. iv (Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-
5/5.1 (The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-
5/5.3-Table 1-Sr. no.v (Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-
5/5.3-Table 1-Sr. no.v (Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-
5/5.3-Table 1-Sr. no.vi (Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-
5/5.3-Table 1-Sr. no.vi (Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-
5/5.3-Table 1-Sr. no.vii (Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-
5/5.3-Table 1-Sr. no.vii (Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-
5/5.5-Table 1-Sr. no.viii (Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-
5/5.5-Table 1-Sr. no.viii (Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-
5/5.6 (UV Resistance, )	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-

-
Complete

12425

BIS, Eastern Regional Laboratory (ERL)

None

IS 11587 (1986)

Specification for structural weather resistant steels

For all grades except for the test mentioned in remarks

- View breakup
Rs 5600/- (rounded off to nearest Rs 50/-) Chemical parameters in Table 1 is Rs. 8600/- (rounded off to nearest 50/-).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Tensile Test)	-
Cl 9 (Bend Test)	-
Cl 10 (Impact Test)	-
Cl 11 (Flattening Test)	-
Cl 12 (Freedom from Defects)	-
Cl 13 (Dimensions)	-
Cl 16 (Mass)	-
Clause 5.1, Table -1 (WR-Fe 480 A, C )	-
Clause 5.1, Table -1 (WR-Fe 480 A, Si)	-
Clause 5.1, Table -1 (WR-Fe 480 A, Mn)	-
Clause 5.1, Table -1 (WR-Fe 480 A, P )	-
Clause 5.1, Table -1 (WR-Fe 480 A, S )	-
Clause 5.1, Table -1 (WR-Fe 480 A, Cr )	-
Clause 5.1, Table -1 (WR-Fe 480 A, Ni)	-
Clause 5.1, Table -1 (WR-Fe 480 A, Cu)	-

-
Chem: except V

12426

BIS, Southern Regional Laboratory (SRL)

None

IS 612 (1992)

Roasted chicory powder - Specification (Third Revision)

3400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.5 Table 1 (Acid Insoluble ash)	-
3.5 Table 1 (Total Ash)	-
3.5 Table 1 (Moisture)	-
3.5 Table 1 (Water soluble Matter )	-
3.1 (Description)	-
3.2 (Cup Test)	-

-
" 500 g Excluding Microscopic Appearance

12427

BIS, Southern Regional Laboratory (SRL)

None

IS 4250 (1980)

Specification for domestic electric food - Mixers (Liquidizers And Grinders) (First Revision)

Rs. 32600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Classification- IS 302-1 )	-
7.1 (Marking- IS 302-1)	-
7.2 (Marking)	-
7.4 (Marking)	-
7.5 (Marking)	-
7.6 (Marking)	-
8 ( Protection Against Electric Shock, IS 302-1)	-
10 (Power Input and Current, IS 302-1)	-
11 (Heating, IS 302-1)	-
13 (Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-
13 (Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-
14 (Transient Over Voltages, IS 302-1)	-
15.1 (Moisture Resistance, IS 302-1)	-
15.2 (Moisture Resistance-Spillage test)	-
15 (Moisture Resistance, IS 302-1)	-
16 (Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-
16 (Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-
19 (Abnormal Operation, IS 302-1)	-
19 (Abnormal Operation, IS 302-1)	-
20 (Stability & Mechanical Hazards, IS 302-1)	-
21 (Mechanical Strength, IS 302-1)	-
21 (Mechanical Strength, IS 302-1)	-
22.2 (Construction)	-
22.3 (Construction)	-
22.4 (Construction)	-
22.5 (Construction)	-
22.6 (Construction)	-
22.8 (Construction)	-
22.9 (Construction)	-
23 (Internal Wiring, IS 302-1)	-
24.2 (Components)	-
24.4 (Components)	-
24.5 (Components)	-
24.6 (Components)	-
24.7 (Components)	-
24.8 (Components)	-
24.9 (Components)	-
25 (Supply Connection and External Flexible Cords, IS 302-1)	-
25 (Supply Connection and External Flexible Cords, IS 302-1)	-
26 (Terminals for External Conductors, IS 302-1)	-
27 (Provision for Earthing, IS 302-1)	-
28 (Screws & Connections, IS 302-1)	-
29 (Clearances and Distances through Insulation, IS 302-1)	-
29 (Clearances and Distances through Insulation, IS 302-1)	-
30 (Resistance to Heat, Fire, Tracking, IS 302-1)	-
31 (Resistance of Rusting, IS 302-1)	-
34.2 (Operational tests- Grinding coffee (for machines which have a dry grinding arrangement))	-
34.3 (Whisking egg whites )	-
34.4 (IDLI batter-Grinding of black gram)	-
34.4 (IDLI batter-Grinding of rice)	-
34.5.1 (a) (Operational test for juicers )	-
34.5.1 (b) (Operational test for juicers )	-
34.5.2 (Operational test for juicers )	-
35 (Temperature withstand test for bowl)	-
37 (Strength of Assembly )	-
9 (Starting, IS 302-1)	-
36 (Test for controls )	-
11 (Heating, IS 302-1)	-
11 (Heating, IS 302-1)	-
11 (Heating, IS 302-1)	-
11 (Heating, IS 302-1)	-

-
" 2 Nos. Complete for IPX0 only.

12428

BIS, Eastern Regional Laboratory (ERL)

None

IS 13620 (1993)

Fusion Bonded Epoxy Coated Reinforcing Bars -

For all grades except for the tests mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7.2 (Continuity Of Coating)	-
Cl 7.3 (Adhesion )	-
4.1 (Carbon- IS 228(Part 1))	-
4.1 (Sulphur- IS 228(Part 9))	-
4.1 (Phosphorous- IS 228(Part 3))	-
4.1 (Sulphur & Phosphorous)	-
4.1 (Carbon Equivalent)	-
Cl 7.1 (Coating Thickness)	-
Cl 7.2 (Continuity Of Coating)	-
Cl 7.3 (Adhesion )	-
Cl 7.1 (Coating Thickness)	-
Cl 7.2 (Continuity Of Coating)	-
Cl 7.3 (Adhesion )	-
Cl 7.1 (Coating Thickness)	-

-
Facility not available for Nb, V, Ti, Al, Cl 4.1 Pull out test, Abrasion Resistance 1 m of coated bar as per IS 13620 & 2 x 1 m of HSDS bar as per IS 1786

12429

BIS, Patna Branch Laboratory (PBL)

None

IS 6444 (1979)

Specification for sulphur dusting powders (First Revision)

Rs.2100.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 Table 1 (Sulphur Content, NV upto 9)	-
2.2 Table 1 (Sulphur Content, NV Above 9 below 50)	-
2.2 Table 1 (Sulphur Content, NV above 50)	-
2.2 Table 1 (Material passing through 75 micron sieve)	-
2.1 (Description)	-
2.2 Table 1 (Bulk Density after compacting)	-

-
All test facilities are available as per the IS

12430

BIS, Patna Branch Laboratory (PBL)

None

IS 3383 (1982)

Specification for wettable sulphur powder

Rs 4200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.2 Table 1 (Wettability)	-
2.2 Table 1 (Sulphur content, NV upto 9)	-
2.2 Table 1 (Sulphur content, NV above 9 below 50)	-
2.2 Table 1 (Sulphur content, NV above 50)	-
2.2 Table 1 (Material passing through 45 micron IS Sieve, after accelerated storage)	-
2.1 (Description)	-

-
All test facilities are available as per the IS

12431

DELHI TEST HOUSE, Azadhpur

8131406

IS 303 (1989)

Plywood for General Purposes -

7000 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others:

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions & Tolerances - Length - Cl. 8)	-	100	For BIS samples: 1.5 times of BIS testing charges
8(Dimensions & Tolerances - Width - Cl. 8)	-	100	For BIS samples: 1.5 times of BIS testing charges
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	100	For BIS samples: 1.5 times of BIS testing charges
8(Dimensions & Tolerances - Squareness - Annexure C)	-	100	For BIS samples: 1.5 times of BIS testing charges
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	100	For BIS samples: 1.5 times of BIS testing charges
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	250	For BIS samples: 1.5 times of BIS testing charges
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	1000	For BIS samples: 1.5 times of BIS testing charges
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	2000	For BIS samples: 1.5 times of BIS testing charges
11.3(Moisture Content - Part 1 of IS 1734)	-	1000	For BIS samples: 1.5 times of BIS testing charges
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	500	For BIS samples: 1.5 times of BIS testing charges
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	0	For BIS samples: 1.5 times of BIS testing charges
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1000	For BIS samples: 1.5 times of BIS testing charges
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	0	For BIS samples: 1.5 times of BIS testing charges
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	1000	For BIS samples: 1.5 times of BIS testing charges
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	0	For BIS samples: 1.5 times of BIS testing charges
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	1000	For BIS samples: 1.5 times of BIS testing charges
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	0	For BIS samples: 1.5 times of BIS testing charges
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	1000	For BIS samples: 1.5 times of BIS testing charges

17 Jun, 2027

-
-

12432

KC INDIA TEST LABORATORIES LLP, GHAZIABAD

9140406

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

13750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	40	20% discount to BIS
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	35	20% discount to BIS
7.1.1(Maximum and minimum outside diameter of socket)	-	50	20% discount to BIS
7.2(Minimum inside diameter of conduit)	-	50	20% discount to BIS
7.3(Length of conduit)	-	50	20% discount to BIS
7.4(Unifomity of The wall Thickness)	-	74	20% discount to BIS
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	177	20% discount to BIS
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	150	20% discount to BIS
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	1635	20% discount to BIS
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	285	20% discount to BIS
10(Resistance to Heat -Ball presure test)	-	168	20% discount to BIS
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	150	20% discount to BIS
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	150	20% discount to BIS
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	150	20% discount to BIS

06 Jun, 2027

-
For sizes 20mm to 50mm.

12433

BIS, Eastern Regional Laboratory (ERL)

None

IS 1989 : Part 2 (1986)

Specification for leather safety boots and shoes: Part 2 for heavy metal industries (Fourth Revision)

For all

Rs 5100/- for safety boots, Rs.4500/- safety shoes View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Marking)	-
7 (Design)	-
8 (a) Upper Leather)	-
8 (b) Lining Leather)	-
8 (c) Bottom Material)	-
8 (d) Steel Toe Cap)	-
8 (e) Tape)	-
8 (f) Bottom Filling)	-
8 (g) Eyelet)	-
8 (h) Toe Compound)	-
8 (i) Threads)	-
8 (j) Rivets)	-
8 (k) Screw Wire)	-
8 (l) Heel Pin)	-
8 (m) Shank)	-
8 (n) Laces)	-
8 (o) Tongue Lining)	-
8 (p) Adhesive)	-
8 (q) Strengthening Piece)	-
8 (r) Leather Components)	-
9 (Manufacture)	-
10 (Finish)	-
11 (a) Boots with Leather Sole and Heel)	-
11 (b) Boots with Rubber Sole and Heel)	-
12 (Performance Test)	-
13 (Design)	-
14 (a) Upper Leather)	-
14 (b) Lining Leather)	-
14 (c) Bottom Material)	-
14 (d) Steel Toe Cap)	-
14 (e) Tape)	-
14 (f) Bottom Filling)	-
14 (g) Eyelet)	-
14 (h) Toe Compound)	-
14 (i) Threads)	-
14 (j) Rivets)	-
14 (k) Screw Wire)	-
14 (l) Heel Pin)	-
14 (m) Shank)	-
14 (n) Laces)	-
14 (o) Tongue Lining)	-
14 (p) Adhesive)	-
14 (q) Leather Components)	-
15 (Manufacture)	-
16 (Finish)	-
17 (a) Shoes with Leather Sole and Heel)	-
17 (b) Shoes with Rubber Sole and Heel)	-
18 (Performance Test)	-

-
Mech- 2 pairs, Chem-1 pair

12434

BIS, Western Regional Laboratory (WRL)

None

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Workmanship)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Silicon)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Manganese)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Phosphorous)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Sulphor)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Carbon)	-

-
Test facilities are not available for the following: 1. Al, Ni, Cr, Mo, Nitrogen

12435

BIS, Eastern Regional Laboratory (ERL)

None

IS 2573 (1986)

Specification for leather gauntlets and mittens (Second Revision)

7400 View breakup
Rs.7400/- (excluding shrinkage temperature test and test of length)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.2.1, Table 1, Sr. No. 1 (Solvent extractable substances)	-
Cl 4.2.1, Table 1, Sr. No. 2 (Chromium content, (as Cr₂O₃))	-
Cl 4.2.1, Table 1, Sr. No. 3 (pH of aqueous extract)	-
Cl.4.1 Fig. 1 to 3. (The three types shall be made to the shape and design as shown in Fig. 1 to 3.)	-
Cl .4.2.1 ( Leather - Chrome tanned/ chrome retanned full grain leather or flesh splits manufactured from cow or buffalo hides conforming to the following requirements shall be used a) The leather and flesh split shall have thickness of 1.0 to 1.5 mm;)	-
Cl.4.3.1.2 ( The hand part shall be cut from the piece of undyed leather and back portion including second, third and fourth fingers from different pieces of undyed leather.)	-
Cl. 4.3.1.3 ( The three different pieces of back portion shall be assembled and stitched together along the edges by a row of stitches. The back thus formed shall be secured with the corresponding front pieces ( palm side ) of the fingers with a row of stitches. The thumb shall be made from two pieces of undyed leather and closed with the hand part by a seam. The seam of the thumb shall be reinforced by a strip of leather and secured by two rows of stitches.)	-
Cl 4.3.1.4 ( The hand part shall be made with the flesh side up and the grain side to remain in contact with the hand.)	-
Cl.4.3.1.5 ( The cuff portion shall be made from two pieces of leather, the inner portion being of leather, chrome tanned, natural colour and the outer portion made of chrome tanned leather, with grain side out.)	-
Cl.4.3.2.6 ( The joint at the palm and the thumb shall be reinforced with the same quality of leather as used for the inner face and stitched by two rows of stitches.)	-
Cl.4.3.1.7 ( A dyed leather piece cut to the shape of a semi-circle shall be stitched on the inner part of the cuff along the joint of the hand and the cuff portions by a single row of stitches as shown in Fig. 1. The semi-circular piece of leather shall be not less than 75 mm in diameter.)	-
Cl.4.3.1.8 ( The gauntlets shall be machine stitched.)	-
Cl.4.3.1.9 ( The number of stitches for all the stitchings shall be 6 to 8 stitches per 25)	-
Cl.4.3.1.10 (All losse ends of stitching threads shall be securely fastened)	-
Cl.4.3.1.11 ( ship and finish, and in all other respects not defined in this standard, the gauntlets shall conform to the approved sample.)	-
Cl.4.3.2.2 ( The inner face of the gauntlets including the inner portion of index, second, third and fourth fingers shall be cut from one piece of leather. The thumb shall be cut from a separate piece of leather.)	-
Cl.4.3.2.3 ( The leather components shall be assembled with the flesh side up, the grain side being inside.)	-
Cl.4.3.2.4 ( The outer face of the gauntlets including index second, third and fourth fingers shall be cut from one piece of canvas.)	-
Cl.4.3.2.5 ( The thumb shall be made with the two cut sides placed together and stitched with one row of stitches. The thumb thus formed shall be attached to palm portion through the cut hole and secured by two rows of stitches as shown in Fig. 2.)	-
Cl.4.3.2.6 ( The joint at the palm and the thumb shall be reinforced with the same quality of leather as used for the inner face and stitched by two rows of stitches.)	-
Cl.4.3.2.7 ( The back portion made of canvas shall be secured with the corresponding palm piece made of leather by two rows of stitches with the edges of both leather and canvas placed inside.)	-
Cl.4.3.2.8 ( A leather strip, 20 mm wide and of the same quality of leather used for the inner face of the gauntlet, shall be used for reinforcing the face of canvas over the knuckles. The reinforcement piece shall be placed side up and secured by four rows of stitches.)	-
Cl.4.3.2.9 ( The cuff portion shall be made from one piece of canvas, the side edges being stitched together by double row of stitches with the ends placed inside. The cuff thus formed shall be secured to the hand part by two rows of stitches with the edges of the material placed inside. The bottom edge of the cuff shall be hemmed ( 6 mm ) with the row edges properly turned in.)	-
Cl.4.3.2.10 ( the gauntlets shall be machine stitched.)	-
Cl.4.3.2.11 ( The number of stitches for all the stitchings shall be 6 to 8 stitches per 25 mm. All loose ends of stitching threads shall be securely fastened.)	-
Cl.4.3.2.12 ( Workmanship and finish, and in all other respects not defined in this standard, the gauntlets shall conform to the approved sample.)	-
Cl.4.3.3.2 ( The palm including the inner component of the compartment for the four fingers shall be cut from one piece of leather and the thumb from a separate piece.)	-
Cl.4.3.3.3 ( The leather components shall be assembled with the flesh side out, the grain side being inside.)	-
Cl.4.3.3.4 ( The back portion including the outer component of the compartment for the four fingers shall be cut from one piece of canvas.)	-
Cl.4.3.3.5 ( The thumb shall be made with the two sides placed inside and stitched with a row of stitches. The thumb thus formed shall be attached to the palm through the cut hole and secured by two rows of stitches.)	-
Cl.4.3.3.6 (The joint at the palm and the thumb shall be reinforced by the same leather material and stitched by two rows of stitches as shown in Fig. 3.)	-
Cl.4.3.3.7 ( The back portion made of canvas shall be secured with the corresponding palm piece made of leather by two rows of stitches with the edges of both the leather and canvas placed inside.)	-
Cl.4.3.3.8 ( The entire palm portion may be lined with canvas of the same quality as used for the back, if required by the purchaser.)	-
Cl.4.3.3.9 (The reinforcement piece shall be placed flesh side out and secured by four rows of stitches.)	-
Cl.4.3.3.10 (The cuff portion shall be made from one piece of canvas, the side edges being stitched together with two rows of stitches with the ends placed inside.)	-
Cl.4.3.3.11 ( The cuff thus formed shall be secured to the hand part by two rows of stitches all along their edges and turned over subsequently.The bottom edges of the cuff shall be hemmed. 6.0 mm with the raw edge properly,turned in.)	-
Cl.4.3.3.12 ( The mittens shall be machine stitched.)	-
Cl.4.3.3.13 ( The number of stitches for all stitchings shall be 6 to 8 stitches per 25 mm)	-
Cl.4.3.3.14 ( All loose ends of stitching threads shall be securely fastened.)	-
Cl.4.3.3.15 (workmanship and finish, and in all other respects not defined in this standard, the mittens shall conform to the approved sample.)	-

-
except shrinkage temperature test of RM, Length in m/Kg

12436

BIS, Western Regional Laboratory (WRL)

None

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

Rs.5400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1, 6.2 (phosphorus)	-
6.1, 6.2 (sulphur)	-
6.1, 6.2 (manganese)	-
6.1, 6.2 (silicon )	-
6.1, 6.2 (carbon)	-
Cl 7 (Workmanship)	-
Cl 8 (Diameter, Ovality & Weight)	-
9.1, table 2 (Tensile Strength)	-
9.1, table 2 (Yield Strength)	-
9.1, table 2 (Elongation)	-
9.2, table 2 (hardness test)	-
12.2 (Bend Test)	-

-
Test facilities are not available for the following: 1, Al, Ni, Cr, Cu, Mo, V, B, Sn 2. Grain size 3. Magnetic Particle 4. Blue Facture Test

12437

CIPET: CENTRE FOR SKILLING AND TECHNICAL SUPPORT (CSTS) - (CIPET), AURANGABAD

7123534

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

41092 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	250	--
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	250	--
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	250	--
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	250	--
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	250	--
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	250	--
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	250	--
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	250	--
4.1(Raw Material )	-	1050	--
4.2 (Fabric)	-	5650	Tape testing for PP = 5650 Tape testing for HDPE = 5000 (Including Density) If pigmented tapeRs. 850 extra for colour fastness
4.2 (Linear Density, 900 denier)	-	500	--
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	500	--
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	500	--
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	250	--
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	250	--
4.3(Sacks)	-	300	--
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	250	--
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	250	--
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	1050	--
4.5(Lamination )	-	1300	1050+250
4.5(Lamination )	-	250	--
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	250	--
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	500	--
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	--
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	--
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	--
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	--
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	--
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1000	--
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	950	--
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	950	--
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	10180	This is UV conditioning for 192 hrs
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	10180	--

31 Dec, 2026

-
For finished product

12438

National Test House (NR) - NTH, Ghaziabad

8101304

IS 1475 : Part 1 (2001)

Self - Contained drinking water coolers - Specification: Part 1 energy consumption and performance (Third Revision)

30000 View breakup
Rs.15000/-( for one water cooler), Rs.30000/- ( for two water cooler0

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.2(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.3(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.4(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.5(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.6(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.7(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.8(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.9(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.1(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.11(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.12(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.13(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.14(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.15(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.16(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.17(COMPONENTS AND THEIR MATERIALS)	-	500	-
7.7.1(Insulation Resistance)	-	3000	-
7.7.2(High Voltage Test)	-	3000	-
7.7.3(Cooling capacity rating test)	-	4000	-
7.7.4(Maximum operating conditions)	-	10000	-
7.8.2(Performance test)	-	1500	-

26 Oct, 2025

-
upto 250 liters

12439

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL

8100534

IS 14928 (2001)

Textiles - Composite synthetic fibre ropes - Specification

3050 View breakup
Rs.2538/- (After 25% discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

31 Dec, 2026

-
-

12440

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL

8100534

IS 14929 (2001)

Textiles - High strength polyolefins copolymer ropes - Specification

5250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(MANUFACTURE)	-	2000	NIL
5.2.1(Construction)	-	300	NIL
5.2.2(Construction)	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. 5.2.1
5.2.3(Construction)	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. 5.2.1
5.3(Structure)	-	300	NIL
5.4( Rope)	-	300	NIL
6.1, Table 1 /Table 2.( REQUIREMENTS:- Linear Density)	-	500	NIL
6.1, Table 1 /Table 2.( Breaking Strength, Min)	-	1100	NIL
6.2, Table 1 and Table 2( Mass of the Coil)	-	250	NIL
6.3( Length of Coil)	-	250	NIL
8.1 (a)( MARKING)	-	250	NIL
8.1 (b)( MARKING)	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. 8.1
8.1 (c)( MARKING)	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. 8.1
8.1 (d)( MARKING)	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. 8.1
8.1 (e)( MARKING)	-	0	CHARGES ALREADY HAS TAKEN IN CLAUSE NO. 8.1

31 Dec, 2026

-
-

12441

Bharat Test House Pvt Ltd 1474 Sonipat Haryana

9135626

IS 15111 : Part 2 (2002)

Self ballasted lamps for general lighting services: Part 2 performance requirements

Self Ballasted Lamps for General Lighting Services

65000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(DIMENSIONS)	-	1500	5% discount for BIS
8.1(STARTING AND RUN-UP)	-	1000	5% discount for BIS
8.2(STARTING AND RUN-UP)	-	1000	5% discount for BIS
9(Lamp Wattage)	-	2500	5% discount for BIS
10(Luminous Flux)	-	2500	5% discount for BIS
11(Colour)	-	3500	5% discount for BIS
12(LUMEN MAINTENANCE)	-	10000	5% discount for BIS
13.1(Life)	-	17500	5% discount for BIS
14(Harmonics)	-	3000	5% discount for BIS
15(Lamp Efficacy)	-	2500	5% discount for BIS
16(Power factor)	-	2500	5% discount for BIS
13.2(Life)	-	17500	5% discount for BIS

19 Mar, 2026

-
-

12442

Bharat Test House Pvt Ltd 1474 Sonipat Haryana

9135626

IS 15111 : PART 1 AND PART 2 (2002)

Self ballasted lamps for general lighting services: Part 1 safety requirements

Compact Fluorescent Lamp

35000 View breakup
Rs. 35000/-(5% discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	125	5% discount for BIS
6.2(Marking)	-	125	5% discount for BIS
6.3(Marking)	-	125	5% discount for BIS
6.4(BIS Certification Marking)	-	125	5% discount for BIS
7(Interchangeability )	-	3000	5% discount for BIS
8(Protection against electric shock)	-	2500	5% discount for BIS
9.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH After HUMIDIT’Y TREATMENT)	-	5000	5% discount for BIS
9.2(The insulation resistance of B 22 caps between shell and contact shall be not less than 5 MΩ When measure with a 500 voltage DC.)	-	2500	5% discount for BIS
9.3(Electric Strength)	-	2500	5% discount for BIS
10(Mechanical strength test )	-	2000	5% discount for BIS
11(Cap Temperature rise test )	-	3000	5% discount for BIS
12(Resistance to heat)	-	5000	5% discount for BIS
13(Resistance to Flame and Ignition)	-	7000	5% discount for BIS
14(Fault Conditions)	-	1750	5% discount for BIS
15(Mercury Content )	-	250	5% discount for BIS

19 Mar, 2026

-
Included w.e.f 13.05.2020

12443

National Test House (NR) - NTH, Ghaziabad

8101304

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

Type - Powder form/ Liquid form

10000 View breakup
Rs.9000/- [ Rs.8000/-for Mechanical, Rs.1000/- for Chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	3000	-
Cl 3.2(Initial & Final)	-	500	-
Cl 3.2(Initial & Final)	-	500	-
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	2000	-
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	2000	-
Clause 3.4(Chloride content)	-	1000	-
Clause 3.4(Chloride content)	-	1000	-

26 Oct, 2025

-
-

12444

DELHI TEST HOUSE, Azadhpur

8131406

IS 4989 : Part 4 (2003)

Multipurpose aqueous film forming foam liquid concentrate for extinguishing hydrocarbon and polar solvent fires - Specification

- View breakup
Rs.31700/- (Provisional testing charges)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

17 Jun, 2027

-
-

12445

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL

8100534

IS 15265 (2003)

Flexible pvc pipes or polymer reinforced thermoplastic hoses for suction and delivery lines of agricultural pumps - Specification

29475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table 1(Internal Diameter)	-	250	-
5.2 Table 2(Length)	-	0	Test charges has already been taken in cl . no. 5.1
6.1 Table 3(Hydrostatic test atatmospheric condition)	-	1000	-
6.2 Table 4(Hydrostatic test at 55± 2°C)	-	1000	-
6.3(Pressure Impulse Test Annex B)	-	15000	-
6.4(Vaccum Test requirement Annex C)	-	2000	-
6.5(Reinforce Facture Test Requirement Annex D)	-	1000	-
6.6(Minimum Bend Radius Requirement- Annex E )	-	1000	-
6.7(Cold Bend Radius Requirement- Annex E )	-	2500	-
6.8(Loss in Mass on Heating- Annex F)	-	1925	-
6.9(Effect of Sunlight)	-	3500	-

31 Dec, 2026

-
-

12446

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL

8100534

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

26800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	1200	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	500	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.3 (Length of Pipe)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4, Table 3(iv) Length of spigot, l1)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4.1 (e3min=0.75e)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 6.1, 6.1.1 .
7(Physical characteristics )	-	0	-
7.1(Appearance:- )	-	300	-
7.2(Colour )	-	0	THE TESTING CHARGES HAS BEEN TAKEN ALREADY IN CLAUSE NO. 7.1.
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1100	-
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	1000	-
8(MECHANICAL CHARACTERISTICS)	-	0	-
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1400	-
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1400	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	850	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	11000	-
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	850	-
9.2 IS 14182(b) Solvent cement)	-	850	-
10(Performance requirements)	-	0	-
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	1000	-
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	0	THE TESTING CHARGES HAS TAKEN ALREADY IN CLAUSE NO. 10.1.1
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	1000	-
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	0	CHARGES HAS ALREADY TAKEN IN CLAUSE NO. 10.2.2.
'7.5 (amdt.7)(Effect on Water (Type test))	-	3000	-
15.4 (b)(Cold impact)	-	1100	-
9.1(PIPE ENDS)	-	250	-

31 Dec, 2026

-
-

12447

Bharat Test House Pvt Ltd 1474 Sonipat Haryana

9135626

IS 418 (2004)

Tungsten filament lamps for domestic and similar general lighting purposes (Fourth Revision)

Tungsten Filament Lamp (Bulb)

72000 View breakup
At rated voltage Upto 25W:Rs.38500/-,Upto 40W: Rs.40000/-,Upto 60W:Rs.45000/-,Upto 100W:Rs.72000/-,Upto 200W:Rs.120000/-, At 110% voltage Upto 25W-Rs.25000/-,Upto 40W-Rs.27000/-, Upto 60W-Rs.31000/-,Upto 100W-Rs.45000/-, Upto 200W-Rs.72000/- (5% discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Marking, IS 418)	-	500	5% discount for BIS
7.1(Lamp Dimensions, IS 418:2004)	-	7500	5% discount for BIS
7.2(Lamp Dimensions, IS 418:2004)	-	7500	5% discount for BIS
8.1(Wattage, IS 418)	-	5000	5% discount for BIS
8.2.1(Luminous Flux Initial, IS 418)	-	5000	5% discount for BIS
8.2.2(Luminous Flux Initial, IS 418)	-	5000	5% discount for BIS
9(Lumen Maintenance, IS 418)	-	15000	5% discount for BIS
10.1(Life Test Requirements, IS 418)	-	20000	5% discount for BIS
10.2(Life Test Requirements, IS 418)	-	20000	5% discount for BIS

19 Mar, 2026

-
-

12448

National Test House (NR) - NTH, Ghaziabad

8101304

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

14500 View breakup
i) Grade EA, EC, ER, ERRXXXX-: Rs.14500/-(Single size), Rs.29000/- (Two size), Rs..36500/-(For three size), Rs.40000/- (Four size), , For physical Rs.11000/-, Radiography test Rs.1000/-, For chemical Rs.2500/- ii) for EB XXXXHJX grade per size Full test (EB XXXX grade): Rs.18000/-(for two size Rs.36000/- three size Rs.44500/- four size Rs.50000/-) , Diffusible hydrogen test-Rs.5000/-, Bend test-Rs.8000/-, Running performance test-Rs.2000/-, Increase mental recover test-Rs.3000/- , For physical Rs.13000/-, Radiography test-:Rs.1000/-, For chemical Rs.4000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 & 8.2(Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	carbon content
6 & 8.2(Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Silicon content
6 & 8.2(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Phosphorus content
6 & 8.2(Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Manganese content
6 & 8.2(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Sulphur content
7.1.1(Diameter of Core Wire)	-	500	Dimension
7.1.2(Length of Electrodes)	-	500	Dimension
7.2.1(Contact End)	-	500	Dimension
7.2.2(Arc striking End)	-	500	Dimension
7.3(Concentricity of Flux covering with core wire)	-	500	Dimension
7.4(Defects of Core wire and Coverings)	-	500	Dimension
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-	3000	Strength Parameter
9.1.2 Table 6 ( Yield Stress -Annex F)	-	1000	Strength Parameter
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-	1000	Strength Parameter
9.1.3 Table 6 ( Impact Strength-Annex F)	-	3000	Strength Parameter
9.2(Butt Weld Bend Test-IS 1599)	-	3000	Strength Parameter
9.6(Radiographic Test- IS 1182)	-	1000	NDT Test
9.3(Running PerformanceTest-Annex H)	-	2000	Running Performance Test
9.4(Increased Metal Recovery Test-IS 13043)	-	3000	Increased Metal Recovery Test
9.5(Diffusible Hydrogen Evaluation Test-IS 11802)	-	5000	Diffusible Hydrogen Evaluation Test
6 & 8.2(Copper- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Titanium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Alumiminium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Cr+Ni+Mo - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	1000	-
6 & 8.2(Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	2000	-

26 Oct, 2025

-
-

12449

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL

8100534

IS 9271 (2004)

Unplasticized polyvinyl chloride (UPVC) single wall corrugated pipes for drainage - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

31 Dec, 2026

-
-

12450

Research & Development Centre for Bicycle and Sewing Machine, Ludhiana

9100634

IS 15449 : Part 2 (2004)

Household zig - Zag sewing machine head: Part 2 accuracy requirements

- View breakup
Rs.10000/- + GST

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

31 Dec, 2026

-
Rs.10000/- is testing charge for entire IS 15449 (Pt-1 to Pt-4)

Bureau of Indian Standards

The National Standards Body of India

Search by IS Number

No Record Found

No Record Found

No Record Found

No Record Found