| 12721 |
Matrix Test Labs
| 8138626
| IS 302 : Part 2 : Sec 25 (2014) |
Safety of household and similar electrical appliances: Part 2 Particular requirements: Section 25 Microwave ovens |
- |
150000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7(Marking and instructions) |
- |
5000 |
|
10% discount to BIS |
| 8(Protection against live parts) |
- |
5000 |
|
10% discount to BIS |
| 10(POWER INPUT AND CURRENT) |
- |
10000 |
|
10% discount to BIS |
| 11(HEATING) |
- |
10000 |
|
10% discount to BIS |
| 13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE) |
- |
5000 |
|
10% discount to BIS |
| 15(HUMIDITY TREATMENT TEST) |
- |
5000 |
|
10% discount to BIS |
| 16(LEAKAGE CURRENT AND ELECTRIC STRENGTH) |
- |
5000 |
|
10% discount to BIS |
| 17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS) |
- |
5000 |
|
10% discount to BIS |
| 18(ENDURANCE) |
- |
35000 |
|
10% discount to BIS |
| 19(ABNORMAL OPERATION) |
- |
10000 |
|
10% discount to BIS |
| 20(STABILITY AND MECHANICAL HAZARDS) |
- |
5000 |
|
10% discount to BIS |
| 21(MECHANICAL STRENGTH) |
- |
5000 |
|
10% discount to BIS |
| 22(CONSTRUCTION) |
- |
5000 |
|
10% discount to BIS |
| 23(INTERNAL WIRING) |
- |
5000 |
|
10% discount to BIS |
| 25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS) |
- |
5000 |
|
10% discount to BIS |
| 26(TERMINALS FOR EXTERNAL CONDUCTORS) |
- |
5000 |
|
10% discount to BIS |
| 27(PROVISION FOR EARTHING) |
- |
5000 |
|
10% discount to BIS |
| 28(SCREWS AND CONNECTIONS) |
- |
5000 |
|
10% discount to BIS |
| 29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION) |
- |
5000 |
|
10% discount to BIS |
| 30(RESISTANCE TO HEAT AND FIRE) |
- |
5000 |
|
10% discount to BIS |
| 31(RESISTANCE TO RUSTING) |
- |
10000 |
|
10% discount to BIS |
| 32(RADIATION, TOXICITY AND SIMILAR HAZARDS) |
- |
10000 |
|
10% discount to BIS |
| 6.0(Classification) |
- |
0 |
|
- |
| 24(COMPONENTS) |
- |
15000 |
|
10% discount to BIS |
| 14(IMPULSE VOLTAGE TEST) |
- |
25000 |
|
10% discount to BIS |
|
31 Dec, 2026 |
-
Excluding: EMI/EMC (Cl.19.11.4.1 to 19.11.4.7), Cord Reel Test Set-up (Cl.22.16), Software (Cl.22.46), Water Pressure Inlet (Cl.22.47), Interlocks (Cl.22.106), Component (Cl.24), Appliance for board ships (Annex-BB) & Salt spray test (Annex-CC). |
| 12722 |
Matrix Test Labs
| 8138626
| IS 15885 : Part 2 : Sec 13 (2012) |
Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules |
- |
75000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7(Marking) |
- |
5000 |
|
10% discount to BIS |
| 8(Protection against accidental contact with live parts) |
- |
5000 |
|
10% discount to BIS |
| 9(Terminals) |
- |
5000 |
|
10% discount to BIS |
| 10(PROVISION FOR EARTHING) |
- |
5000 |
|
10% discount to BIS |
| 11(MOISTURE RESISTANCE) |
- |
5000 |
|
10% discount to BIS |
| 12(Electric Strength) |
- |
5000 |
|
10% discount to BIS |
| 14(Fault conditions) |
- |
10000 |
|
10% discount to BIS |
| 15(Transformer heating) |
- |
15000 |
|
10% discount to BIS |
| 16(Construction) |
- |
5000 |
|
10% discount to BIS |
| 17(Creepage distance and clearances) |
- |
5000 |
|
10% discount to BIS |
| 18(Screws, current carrying parts and connections) |
- |
5000 |
|
10% discount to BIS |
| 19(Resistance to heat, fire and tracking) |
- |
10000 |
|
10% discount to BIS |
| 20(Resistance to corrosion) |
- |
10000 |
|
10% discount to BIS |
|
31 Dec, 2026 |
-
Excluding: Components: Enclosure, Bridging resistor in primary circuit, Capacitor and RC units, RF suppression (X-Y capacitors), Inductor, MOV/VDR, SMPS/Mains Transformer, PCB material, Metal base PCB for LED, Transparent cover, Bobbin, Insulated tape, Heat shrinkage sleeve, Connector, Fuse, Internal wire, LED, Opto-coupler, EMI/EMC filter, Winding wire, Thin sheet materials etc. |
| 12723 |
Matrix Test Labs
| 8138626
| IS 16102 : Part 1 (2012) |
Self - Ballasted led lamps for general lighting services: Part 1 safety requirements |
- |
80000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5(Marking) |
- |
5000 |
|
10% Discount to BIS |
| 6(Interchangeability) |
- |
10000 |
|
10% Discount to BIS |
| 7(Protection against accidental contact with live parts) |
- |
5000 |
|
10% Discount to BIS |
| 8(Insulation Resistance and Electric Strength) |
- |
15000 |
|
10% Discount to BIS |
| 9(MECHANICAL STRENGTH) |
- |
10000 |
|
10% Discount to BIS |
| 10(cap temperature) |
- |
10000 |
|
10% Discount to BIS |
| 11(Resistance to Heat) |
- |
10000 |
|
10% Discount to BIS |
| 12(Resistance to Flame and Ignition) |
- |
10000 |
|
10% Discount to BIS |
| 13(Fault conditions) |
- |
10000 |
|
10% Discount to BIS |
| 14(Creepage distance and clearances) |
- |
5000 |
|
10% Discount to BIS |
|
31 Dec, 2026 |
-
Restricted to Cap type B22d, E14 & E27 only. |
| 12724 |
Building Fire Research Centre, Mysore
| 6124933
| IS 15683 (2018) |
Portable Fire Extinguishers — Performance and Construction — Specification ( First Revision ) |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
No Record Found
|
|
15 Jul, 2021 |
-
- |
| 12725 |
BIS, Central Laboratory (CL)
| None
| IS 15450 (2004) |
Polyethylene/aluminium/polyethylene composite pressure pipes for hot and cold water supplies - Specification |
- |
5250 View breakup
Rs. 5250/- excluding material, pressure rating, density, hydraulic characteristics, type test (Cl. 11.1), carbon black content & dispersion and pigment dispersion.
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 8, Table-2 (Dimension) |
- |
|
|
|
|
- |
-
- |
| 12726 |
BIS, Central Laboratory (CL)
| None
| IS 12823 (2015) |
Prelaminated Particle Boards from Wood and other Lignocellulosic Material - Specification ( First Revision ) |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl 10.13 & Annex F ( Test For Resistance to Cigarette Burn) |
- |
|
|
|
| Cl 10.12 & Annex E ( Test For Crack Resistance) |
- |
|
|
|
| Cl 10.9 (Test For Screw Withdrawal Strength) |
- |
|
|
|
| Cl 10.8 (For Determination of Tensile Strength Perpendicular to Surface After Ageing Test) |
- |
|
|
|
| Cl 10.7 (For Determination of Tensile Strength Perpendicular to Surface) |
- |
|
|
|
| Cl 10.6 (Tesr For Modulus Of Elasticity & Mudulus Of Rupture) |
- |
|
|
|
| Cl 10.5 (For Swelling in water Test ) |
- |
|
|
|
| Cl 10.4 (For Water AbsorptionTest ) |
- |
|
|
|
| Cl 10.3 (Test For Moisture Content) |
- |
|
|
|
| Cl 10.2 (Test For Density) |
- |
|
|
|
| Cl 8 (Dimensions & Tolerances) |
- |
|
|
|
| Cl 7 (Finish) |
- |
|
|
|
| Cl 6 (Manufacture) |
- |
|
|
|
| Cl 10.15 (Test for Formaldehyde Content/Emission) |
- |
|
|
|
|
- |
-
Sample Test Parameter not available in CL:
"10.4 Test for Water Absorption, 10.5 Test for Swelling in Water, 10.6 Test for Modulus of Rupture (MOR)
and Modulus of Elasticity (MOE), 10.8 Test for Tensile Strength Perpendicular
to Surface After Ageing, 10.10 Test for Abrasion Resistance, 10.11 Test for Resistance to Steam, 10.14 Test for Resistance to Stain."
SIZE: One Board For All Tests
Sample Size without dimensional measurements:Length-1200 mm, width-1200 |
| 12727 |
Research & Development Centre for Bicycle and Sewing Machine, Ludhiana
| 9100634
| IS 2403 (2014) |
Short - Pitch transmission precision roller and bush chains, attachments and associated chain sprockets (Third Revision) |
- |
4500 View breakup
Rs.4,500/- + GST
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3.3 Table-1,2(Dimensions- Pitch- p) |
- |
0 |
|
+ GST@18% |
| 3.3 Table-1,2(Dimensions- Roller diameter- d1) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Width between
inner plates- b1) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Bearing pin body diameter- d2) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions-Bush bore-d3) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Chain path depth- h1) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions-Inner plate depth- h2) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions-Outer plate depth- h3) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Cranked link dimensions- l2) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Cranked link dimensions- c) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Transverse pitch- pt) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Width over inner link- b2) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Width between outer plates- b3) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Width over bearing pins- b4) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Width over bearing pins- b5) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Width over bearing pins- b6) |
- |
0 |
|
-- |
| 3.3 Table-1,2(Dimensions- Additional width for joint fastener- b7) |
- |
0 |
|
-- |
| 3.4.2(Tensile Test) |
- |
0 |
|
-- |
| 3.4.3(Preloading) |
- |
0 |
|
-- |
| 3.4.4(Length validation- Measuring load) |
- |
0 |
|
-- |
| 3.4.4(Length validation- Length) |
- |
0 |
|
-- |
| 3.4.5(Dynamic testing) |
- |
0 |
|
-- |
|
31 Dec, 2026 |
-
EXCLUDING - Dynamic Strength test |
| 12728 |
BIS, Central Laboratory (CL)
| None
| IS 8808 (2019) |
Burners for oil pressure stoves and oil pressure heaters - Specification (Third Revision) |
- |
Rs. 6600/ View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4 (TYPES) |
- |
|
|
|
| 6.1 (SHAPE, SIZES AND DIMENSIONS - FIG. 1A,1B AND 2) |
- |
|
|
|
| 6.1 (SHAPE, SIZES AND DIMENSIONS - FIG. 3A,3B AND 3C) |
- |
|
|
|
| 8 (FINISH) |
- |
|
|
|
| 10.1 (TESTS-Pressure Tests) |
- |
|
|
|
| 10.2 (TESTS-Tests for Thermal Efficiency) |
- |
|
|
|
| 5 (MATERIALS- Roarer type
burner) |
- |
|
|
|
| 5 (MATERIALS-Silencer type
burner) |
- |
|
|
|
| 5 (MATERIALS- Tube type
burner) |
- |
|
|
|
|
- |
-
EXCLUDING "-; 10.2 -Thermal Efficiency,10.1 -Pressure Tests," |
| 12729 |
Research & Development Centre for Bicycle and Sewing Machine, Ludhiana
| 9100634
| IS 2415 (2015) |
Cycle - Rubber tubes (Moulded/ Jointed) - Specification (Fourth Revision) |
- |
8700 View breakup
Rs.8700/- + GST
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.1,3.4, Annex A & Table 2.( Flat Length ) |
- |
0 |
|
+GST@18% |
| 5.2, Annex A(Thickness) |
- |
0 |
|
-- |
| 5.1,3.5, Annex A & Table 2.(Flat Width) |
- |
0 |
|
-- |
| 5.2.1(Uniformity of Thickness) |
- |
0 |
|
-- |
| 6.1,Table 3(i)Tensile strength:) |
- |
0 |
|
-- |
| 6.1,Table 3(ii)Elongation at break ) |
- |
0 |
|
-- |
| 6.2(iii)Tension set: ) |
- |
0 |
|
-- |
| 6.3 (a)( Ageing Test:- Tensile strength :) |
- |
0 |
|
-- |
| 6.3(b)( Ageing Test :- Elongation at break) |
- |
0 |
|
-- |
| 6.4.3( Strength of splice on moulded tube) |
- |
0 |
|
-- |
| 6.7.3(Manufacture and Workmanship) |
- |
0 |
|
-- |
|
31 Dec, 2026 |
-
0.0 |
| 12730 |
BIS, Central Laboratory (CL)
| None
| IS 9762 (1994) |
Specification for polyethylene floats (Spherical) for float valves |
- |
Rs.4500/ View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| cl 8.1 (Leakage & water ab. Test) |
- |
|
|
|
| cl 8.2 (Deflection Test) |
- |
|
|
|
| cl 8.3 (Impact test) |
- |
|
|
|
| cl 8.4 (Boss test) |
- |
|
|
|
|
- |
-
- |
| 12731 |
Research & Development Centre for Bicycle and Sewing Machine, Ludhiana
| 9100634
| IS 6218 (2008) |
Bicycle - Mudguards - Specification (First Revision) |
- |
7200 View breakup
Rs.7200/- + GST
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Clause-3(Carbon) |
- |
0 |
|
-- |
| Clause-3(Sulphur) |
- |
0 |
|
-- |
| Clause-3(Phosphorus) |
- |
0 |
|
-- |
| Clause-3(Manganse) |
- |
0 |
|
-- |
| Clause-3(Silicon) |
- |
0 |
|
-- |
| Clause-3(Aluminium) |
- |
0 |
|
-- |
| Clause-3(Chromium) |
- |
0 |
|
-- |
| Clause-3(Nickel) |
- |
0 |
|
-- |
| Clause-3(Niobium) |
- |
0 |
|
-- |
| Clause-3(Vanadium) |
- |
0 |
|
-- |
| Clause-3(Titanium) |
- |
0 |
|
-- |
| Clause-3(Molybdenum) |
- |
0 |
|
-- |
| Clause-3(Boron) |
- |
0 |
|
-- |
|
31 Dec, 2026 |
-
. |
| 12732 |
BIS, Central Laboratory (CL)
| None
| IS 3989 (2009) |
Centrifugally cast (Spun) iron spigot and socket soil, waste, ventilating and rainwater pipes, fittings and accessories - Specification (Third Revision) |
- |
Rs. 3600/- and Material testing charges as per relevant View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5 (Hydrostatic Test) |
- |
|
|
|
| 6.2,6.3, Table 1 & 4 (Dimensions & Tolerances, mm) |
- |
|
|
|
| 6.2,6.3, Table 1 & 4 (Equal branches without access door,mm) |
- |
|
|
|
| 6.2,6.3, Table 1 & 4 (Barrel) |
- |
|
|
|
| 6.2,6.3, Table 1 & 4 (Socket) |
- |
|
|
|
| 6.2,6.3, Table 1 & 4 (Joint Thickmess) |
- |
|
|
|
| 8 (Coating Test) |
- |
|
|
|
|
- |
-
Since the composition of cast iron shall be left to the discretion ofthe manufacturer , as such element to be tested with specified requirement and tolerances if any may please be declared with method of testing. Sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm.;
EXCLUDING -; hydraulic test |
| 12733 |
Research & Development Centre for Bicycle and Sewing Machine, Ludhiana
| 9100634
| IS 623 (2008) |
Bicycle - Bicycle frames - Specification (Third Revision) |
- |
19000 View breakup
Rs.19000/- + GST
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.1(FRAME TUBES ) |
- |
0 |
|
+ GST@18% |
| 4.1(CHAIN SIDE) |
- |
0 |
|
-- |
| 4.1(BACK STAY) |
- |
0 |
|
-- |
| 4.2(SCREW THREADS) |
- |
0 |
|
-- |
| 7.1(a) TRUENESS OF FRAME) |
- |
0 |
|
-- |
| 7.2.1(b) IMPACT TEST (Falling Mass)) |
- |
0 |
|
-- |
| 7.2.2(c) IMPACT TEST (Falling Frame & Fork Assembly)) |
- |
0 |
|
-- |
| 7.3(d) TEST FOR FINISH) |
- |
0 |
|
-- |
|
31 Dec, 2026 |
-
0.0 |
| 12734 |
Matrix Test Labs
| 8138626
| IS 16242 : Part 1 (2014) |
Uninterruptible power systems (UPS): Part 1 general and safety requirements for UPS |
- |
125000 View breakup
Rs.1,25,000/- UPS/ Invertors Up to 5
kVA)
[10% discount to BIS]
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.6(Power interface) |
- |
15000 |
|
10% discount to BIS |
| 4.7(Marking & instructions) |
- |
10000 |
|
10% discount to BIS |
| 5.1(Protection against shock and energy hazards) |
- |
5000 |
|
10% discount to BIS |
| 5.2(Requirement of auxiliary circuits) |
- |
5000 |
|
10% discount to BIS |
| 5.3(Protective earthing and bonding) |
- |
5000 |
|
10% discount to BIS |
| 5.5(Over current and earth fault condition) |
- |
5000 |
|
10% discount to BIS |
| 5.6(Safety interlocks) |
- |
5000 |
|
10% discount to BIS |
| 5.7(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION) |
- |
5000 |
|
10% discount to BIS |
| 6.1(Wiring, connections and supply) |
- |
5000 |
|
10% discount to BIS |
| 6.2(Connection to power) |
- |
5000 |
|
10% discount to BIS |
| 6.3(Wiring terminals for external power conductors) |
- |
5000 |
|
10% discount to BIS |
| 7.2(STABILITY) |
- |
5000 |
|
10% discount to BIS |
| 7.3(MECHANICAL STRENGTH) |
- |
5000 |
|
10% discount to BIS |
| 7.4(Construction details) |
- |
5000 |
|
10% discount to BIS |
| 7.5(Resistance to fire) |
- |
10000 |
|
10% discount to BIS |
| 7.6(Battery location) |
- |
5000 |
|
10% discount to BIS |
| 7.7(Temperature rise) |
- |
15000 |
|
10% discount to BIS |
| 8.1(General procision for earth leakage) |
- |
5000 |
|
10% discount to BIS |
| 8.2(Electric Strength) |
- |
5000 |
|
10% discount to BIS |
| 8.3(Abnormal operating and fault conditions) |
- |
10000 |
|
10% discount to BIS |
| 9.0(Connection to telecommunication networks) |
- |
10000 |
|
10% discount to BIS |
| 4.5(Components) |
- |
15000 |
|
10% discount to BIS |
| 5.4(AC and DC power isolation) |
- |
0 |
|
- |
| 7.1(Enclosure) |
- |
5000 |
|
10% discount to BIS |
|
31 Dec, 2026 |
-
Following Additional
Test Facility included
w.e.f. 18.09.2018:
Protection against
ingress of foreign
objects (IPX7 & IPX8
only) (Cl.1.2 & AnnexH).
Excluding: Non-linear
loads (Cl.3.3),
Components (Cl.4.5 /
RD 1.5), Protection of
Personnel-Safety
Interlocks (Cl. 5.6/ RD
Cl.2.8.5, Cl.2.8.7.1 to
Cl.2.8.7.3),
Semiconductor devices
(Cl.2.10.5.4 of RD) and
Insulation in wound
components
(Cl.2.10.5.11 of RD). |
| 12735 |
Matrix Test Labs
| 8138626
| IS 10322 : Part 5 : Sec 1 (2012) |
Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision) |
- |
80000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 6.0(Marking) |
- |
5000 |
|
10% discount to BIS |
| 7.0(Construction) |
- |
10000 |
|
10% discount to BIS |
| 8.0(Creepage Distance and Clearances) |
- |
5000 |
|
10% discount to BIS |
| 9.0(Provision for earthing) |
- |
5000 |
|
10% discount to BIS |
| 10.0(Terminals) |
- |
10000 |
|
10% discount to BIS |
| 11.0(External & Internal Wiring) |
- |
5000 |
|
10% discount to BIS |
| 12.0(Protection against electric shock) |
- |
10000 |
|
10% discount to BIS |
| 13.0(Endurance Tests and Thermal Tests) |
- |
20000 |
|
10% discount to BIS |
| 14.0(Resistance to Dust & Moisture) |
- |
15000 |
|
10% discount to BIS |
| 15.0(Insulation Resistance and Electric Strength) |
- |
10000 |
|
10% discount to BIS |
| 16.0(Resistance to Heat , fire and tracking) |
- |
10000 |
|
10% discount to BIS |
| 4(General Test Requireements) |
- |
0 |
|
- |
| 5(Classification of Luminaires') |
- |
0 |
|
- |
|
31 Dec, 2026 |
-
Following Additional
Test Facility included
w.e.f. 18.09.2018:
Resistance to dust, solid
objects & moisture for
IPX7 & IPX8 (Cl.9.2.8 &
Cl.9.2.9) as per (RD) IS
10322(Part-1):2014.
Excluding:
Electromechanical
Contact System
(Cl.4.11.6), UV
Radiation (Cl.4.24,
Annex-P), Short
circuit protection (Cl.
4.26.2) as per (RD) IS
10322(Part-1):2014 and
Photometric test (Cl.17). |
| 12736 |
Matrix Test Labs
| 8138626
| IS 16046 : Part 2 (2018) |
Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes ” Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for Use in Portable Applications Part 2 Lithium Systems ( Second Revision ) |
- |
180000 View breakup
Rs.1,80,000/- [10% discount to BIS]
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5(General Safety Considerations) |
- |
5000 |
|
10% discount to BIS |
| 6(Type Test and Sample Size) |
- |
5000 |
|
10% discount to BIS |
| 7.1(Charging procedure for test purposes) |
- |
20000 |
|
10% discount to BIS |
| 7(Specific requirements and tests) |
- |
5000 |
|
10% discount to BIS |
| 7.2(Intended Use) |
- |
35000 |
|
10% discount to BIS |
| 7.3(Reasonably foreseeable misuse) |
- |
110000 |
|
10% discount to BIS |
| 10(Packaging) |
- |
0 |
|
- |
| 8.2(Small Cell and battery safety information) |
- |
5000 |
|
10% discount to BIS |
| 5.8(Battery Safety Components) |
- |
15000 |
|
10% discount to BIS |
| 9(Marking) |
- |
3000 |
|
10% discount to BIS |
| 9.1(Cell Marking) |
- |
3000 |
|
10% discount to BIS |
| 5.2(Insulation and Wiring) |
- |
5000 |
|
10% discount to BIS |
| 5.3(Venting) |
- |
0 |
|
- |
| 5.4(Temperature, Voltage and Current Management) |
- |
0 |
|
- |
| 5.5(Terminal Contacts) |
- |
0 |
|
- |
| 5.6(Assembly of Cells into batteries) |
- |
0 |
|
- |
| 5.7(Quality Plan) |
- |
0 |
|
- |
| 4(Parameter Measurement Tolerances) |
- |
0 |
|
- |
| 5.1(General) |
- |
0 |
|
- |
| 8(Information for safety) |
- |
0 |
|
- |
| 9.2(Battery Marking) |
- |
0 |
|
- |
| 9.3(Caution for ingestion of small cells and batteries) |
- |
0 |
|
- |
| 9.4(Other information) |
- |
0 |
|
- |
|
31 Dec, 2026 |
-
REVISED VERSION
Included w.e.f.
14.01.2019. |
| 12737 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 14333 (1996) |
High Density Polyethylene Pipe For Sewerage - |
- |
11475 View breakup
Rs.8681/-,
Rs.3044/- Raw material
(After 25% discount for BIS)
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 10(Marking) |
- |
0 |
|
Nil |
| 3(Designation) |
- |
0 |
|
Nil |
| 4(Colour) |
- |
300 |
|
Nil |
| 6(Dimensions of pipes) |
- |
250 |
|
Nil |
| 7(Visual Appearance) |
- |
300 |
|
Nil |
| 8.1(Hydraulic characteristics) |
- |
6400 |
|
Type test for 168 hrs = Rs. 4800/- and Acceptance test for 48 hrs = Rs. 1600/- |
| 8.2(Reversion) |
- |
1000 |
|
Test charges Rs. 700 plus specimen charges Rs.300/- (25 % discount is not applicable in specimen charges) |
| 8.3(Density) |
- |
500 |
|
Nil |
| 8.4(Melt Flow Rate) |
- |
1100 |
|
Nil |
| Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content) |
- |
925 |
|
Nil |
| Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion) |
- |
700 |
|
Nil |
|
31 Dec, 2026 |
-
Upto 600 mm DN and excluding Chemical resistance classification (Annexure-D) |
| 12738 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 14252 (2015) |
Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision) |
- |
19140 View breakup
Rs.16903/-
(After 25% discount for BIS)
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 3.1(Raw Material) |
- |
1050 |
|
Nil |
| 3.2(Tapes – Width
) |
- |
250 |
|
Nil |
| 3.2(Tapes – Linear Density
) |
- |
250 |
|
Nil |
| 3.3(Tying Cord) |
- |
0 |
|
Charges already taken |
| 3.3(Tying Cord) |
- |
0 |
|
Charges already taken |
| 3.3(Tying Cord) |
- |
0 |
|
Charges already taken |
| 3.4(Sack) |
- |
0 |
|
Charges already taken |
| 3.4.1(Seam) |
- |
0 |
|
Charges already taken |
| 3.4.1(Seam) |
- |
0 |
|
Charges already taken |
| 3.4.1(Seam) |
- |
0 |
|
Charges already taken |
| 3.4.1(Seam) |
- |
0 |
|
Charges already taken |
| 4.1 and Table 1 i a(Dimensions Outside Length) |
- |
250 |
|
Nil |
| 4.1 and Table 1 i b(Dimensions Outside Width) |
- |
0 |
|
Charges already taken in clause no. 4.1 and Table 1 i a |
| 4.1 and Table 1 ii(Ends per dm ) |
- |
250 |
|
Nil |
| 4.1 and Table 1 iii(Picks per dm ) |
- |
250 |
|
Nil |
| 4.2 and Table 1 iv(Mass of sack
) |
- |
300 |
|
Nil |
| 4.1 and Table 1 v a(Average breaking strength of fabric Warpway
) |
- |
1100 |
|
Nil |
| 4.1 and Table 1 v b(Average breaking strength of fabric Weftway
) |
- |
1100 |
|
Nil |
| 4.1 and Table 1 vi(Average Breaking strength of bottom seam ) |
- |
1100 |
|
Nil |
| 4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise) |
- |
1100 |
|
Nil |
| 4.1 and Table 1 vii b(Elongation at break of fabric Widthwise ) |
- |
1100 |
|
Nil |
| 4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering ) |
- |
10340 |
|
25% discount is not applicable in conditioning charges |
| 4.1 and Table 1 ix(Ash content ) |
- |
950 |
|
Nil |
|
31 Dec, 2026 |
-
Included w.e.f. 29.06.2017. |
| 12739 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 14151 : Part 1 (1999) |
Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision) |
- |
23025.00 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl.3(CLASSIFICATION OF PIPES) |
- |
0 |
|
Nil |
| 4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.) |
- |
1100.00 |
|
Nil |
| 4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.) |
- |
1125.00 |
|
Test charges Rs. 500.00 plus specimen charges Rs. 625.00 |
| 4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’) |
- |
1100.00 |
|
Nil |
| Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content) |
- |
925.00 |
|
Nil |
| 4.3(Anti-oxidant) |
- |
0 |
|
Test facility is not available |
| 5.1 table -1(DIMENSIONS OF PIPES) |
- |
500.00 |
|
Nil |
| 5.1.2(Ovality) |
- |
0 |
|
Charges already taken in clause no. 5.1 TABLE-1 DIMENSIONS OF PIPES |
| 6.1(VISUAL APPEARANCE) |
- |
300.00 |
|
Nil |
| 7.1 Table -2(Hydraulic Characteristics) |
- |
0 |
|
Charges is taken in clause no. 7.1 |
| 7.2(Reversion Test) |
- |
1000 |
|
Test charges Rs. 700.00 + specimen charges Rs. 300.00 |
| 7.3(Tensile Test) |
- |
1350.00 |
|
Test charges Rs. 1100.00 + specimen charges Rs. 250.00 |
| 7.4table-2(Fusion Compatibility Test) |
- |
0 |
|
Charges is taken in clause no. 7.4 a) Quality test, b) Acceptance test |
| 7.5(Density) |
- |
1125.00 |
|
Nil |
| 7.6(Melt now Rate (MFR)) |
- |
1100.00 |
|
Nil |
| (Cl.4.2)(Carbon black- b) Dispersion of carbon black) |
- |
700.00 |
|
NIL |
| Cl.5(Dimensions of pipe - i) Outside diameter) |
- |
0 |
|
Charges already taken in clause no. 5.1 TABLE-1 DIMENSIONS OF PIPES |
| Cl.5(Dimensions of pipe - ii) Wall thickness minimum) |
- |
0 |
|
Charges already taken in clause no. 5.1 TABLE-1 DIMENSIONS OF PIPES |
| Cl.5(Dimensions of pipe - ii) Wall thickness maximum) |
- |
0 |
|
Charges already taken in clause no. 5.1 TABLE-1 DIMENSIONS OF PIPES |
| Cl 7.1(Hydraulic Characteristics - Acceptance test) |
- |
1600.00 |
|
- |
| Cl 7.1(Hydraulic Characteristics - Quality test) |
- |
4800.00 |
|
- |
| Cl.7.2)(Reversion Test) |
- |
0 |
|
Charges already taken in clause no. 7.2 |
| Cl.7.3(Tensile Test- i) Tensile Strength) |
- |
0 |
|
Charges is already taken in clause no. 7.3 |
| Cl.7.3(Tensile Test - ii)Elongation at Break) |
- |
0 |
|
Charges is already taken in clause no. 7.3 |
| Cl.7.4(Fusion Compatibility Test- a) Quality test) |
- |
1600.00 |
|
- |
| Cl.7.4(Fusion Compatibility Test- b) Acceptance test) |
- |
4800.00 |
|
- |
|
31 Dec, 2026 |
-
EXCLUSION: Antioxidant test (Cl.4.3) |
| 12740 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 13592 (2013) |
Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System |
- |
17800 View breakup
Type-A: Rs.12400/-, Rs.825/- for PVC Resin, Rs.21800/- for Alternate (Optional);
Type-B: Rs.12725/-, Rs.825/- for PVC Resin, Rs.21800/- for alternate
(After 25% discount for BIS)
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| Cl.5(Surface colour of the pipes shall be dark shade of grey) |
- |
300 |
|
Nil |
| Cl6.3(The composition shall be based on PVC resin
having a K-value of 64 or greater when tested in
accordance with IS 4669) |
- |
1100 |
|
Nil |
| Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6)) |
- |
500 |
|
Nil |
| Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum)) |
- |
0 |
|
Charges already taken in clause no. 7.1 |
| Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading)) |
- |
0 |
|
Charges already taken in clause no. 7.1 |
| Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or
6 metres either plain or with socket for solvent
cementing/grooved socket. Tolerances on specified
length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent
cementing/grooved socket shall be as given in Fig. 1.) |
- |
0 |
|
Charges already taken in clause no. 7.1 |
| Cl.7.3.1(Minimum wall thickness of socket on pipes shall
be as given in Table 2 read with Fig. 2 and Fig. 3.) |
- |
0 |
|
Charges already taken in clause no. 7.1 |
| Cl.7.3.2(Dimensions of sockets for solvent cementing and
grooved sockets of pipes shall be as given in Tables 3
and 4 respectively, read with Fig. 2 and 3.) |
- |
0 |
|
Charges already taken in clause no. 7.1 |
| Cl.8.1(The internal and external surface of the pipes shall be
smooth and clean, and free from grooving and other
defects. The end shall be clearly cut and shall be square
with the axis of the pipe. The end may be chamfered
on the plain side.) |
- |
300 |
|
Nil |
| Cl.8.2(When tested by the method described in IS 12235
(Part 5), a length of pipe sample of 200 ± 20 mm shall
not alter in length by more than 5 percent. In the case
of socket ended pipes, this test shall be carried out on
the plain portion of pipe taken at least 100 mm away
from the root of the socket.) |
- |
1000 |
|
Test charges Rs. 700/- plus specimen charges Rs. 300/- (25% discount is not applicable in specimen charges) |
| Cl8.3(This test shall be carried out for socket end pipes only.
When tested by the method described in IS 12235
(Part 6), the test specimens shall not show blisters,
excessive delamination or cracking or signs of weld
line splitting.) |
- |
700 |
|
Nil |
| Cl.8.4(When determined in accordance with IS 12235 (Part 2),
the vicat softening temperature of the specimen shall
not be less than 79°C.) |
- |
1100 |
|
Nil |
| Cl.8.5(After the required
period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show
difference of more than 20 percent of their initial tensile
strengths) |
- |
3500 |
|
Nil |
| Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid) |
- |
2500 |
|
Test charges Rs. 2000/- plus specimen charges Rs. 500/- (25% discount is not applicable in specimen charges) |
| Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than
10 percent. Mass of striker and height of fall shall be
as per Annex A.) |
- |
1400 |
|
Test charges Rs. 1100/- plus specimen charges Rs. 300/- (25% discount is not applicable in specimen charges) |
| Cl.10.2(When determined in accordance with the method
described in IS 12235 (Part 13), the tensile strength at
break shall not be less than 45 MPa.) |
- |
2700 |
|
Test charges Rs. 2200/- plus specimen charges Rs. 500/- (25% discount is not applicable in specimen charges) |
| Cl.10.3(The axial shrinkage shall not exceed 2 percent when
determined in accordance with Annex B.) |
- |
700 |
|
Nil |
| Cl.11.(Jointing of solvent
cementing joints is to be carried out using solvent
conforming to IS 14182.
Apply a pressure of 0.05 MPa for a period of 15 min
and there should be no leakage at any joint.) |
- |
1000 |
|
Nil |
| Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane) |
- |
1000 |
|
Nil |
|
31 Dec, 2026 |
-
0.0 |
| 12741 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 13488 (2008) |
Irrigation equipment - Emitting pipe systems - Specification (First Revision) |
- |
13900 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density) |
- |
1125 |
|
Test charges Rs.500/- plus specimen charges Rs. 625/- (25% discount is not applicable in specimen charges) |
| 5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989) |
- |
700 |
|
Nil |
| 5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963) |
- |
925 |
|
Nil |
| 5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963) |
- |
700 |
|
Nil |
| 6.2.2(Fittings) |
- |
0 |
|
Nil |
| 6.3(General) |
- |
300 |
|
Nil |
| 6.3(General) |
- |
0 |
|
Charges already taken in clause no. 6.3 |
| 8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes) |
- |
1000 |
|
Nil |
| 8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes) |
- |
0 |
|
Charges already taken in clause no. 8.1.2 |
| 8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure) |
- |
1000 |
|
Nil |
| 8.2.1(Unregu/Qt~d Emining Pipe) |
- |
0 |
|
Charges already taken in clause no. 8.2 |
| 8.2.2(Regulated Emitting Pipes) |
- |
0 |
|
Charges already taken in clause no. 8.2 |
| 8.3.1(Wall Thickness ofEmitting Pipe) |
- |
400 |
|
Nil |
| 8.3.2(Inside Diameter ofEmitting Pipe) |
- |
0 |
|
Charges already taken in clause no. 8.3.1 |
| 8.3.3(Flow Paths in Emitting Unit) |
- |
0 |
|
Charges already taken in clause no. 8.3.1 |
| 8.3.4(Spacing ofEmitter Units) |
- |
0 |
|
Charges already taken in clause no. 8.3.1 |
| 8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature) |
- |
1000 |
|
Nil |
| 8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature) |
- |
160 |
|
Nil |
| 8.5(Resistance to Tension at Elevated Temperature) |
- |
1100 |
|
Nil |
| 8.5(Resistance to Tension at Elevated Temperature) |
- |
0 |
|
Charges already taken in clause no. 8.5 |
| 8.5(Resistance to Tension at Elevated Temperature) |
- |
0 |
|
Charges already taken in clause no. 8.5 |
| 8.6(Resistance to Pull Out of Joints Between Fitting and Emitting
IS 13479) |
- |
400 |
|
Nil |
| 8.7.1(Resistance of PE Emitting Pipe to
Environmental Stress Cracking -Acceptance Test
Annex D of IS 12786) |
- |
1200 |
|
Nil |
| 8.7.2(Resistance of PE Emitting Pipe to
Environmental Stress Cracking - Type Test
Annex D of IS 12786) |
- |
1600 |
|
Nil |
| 8.8(Determination of Emitting Unit Exponent) |
- |
600 |
|
Nil |
|
31 Dec, 2026 |
-
- |
| 12742 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 13422 (1992) |
Disposable surgical rubber gloves specification |
- |
12000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.4(Sterility) |
- |
2000 |
|
Nil |
| 4(TYPES) |
- |
0 |
|
Nil |
| 5.2.1(General Characteristics and Dimensions) |
- |
250 |
|
Nil |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Length) |
- |
250 |
|
Nil |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Width) |
- |
250 |
|
Nil |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Thickness of Finger) |
- |
250 |
|
Nil |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Thickness of Palm) |
- |
0 |
|
Charges already taken in clause no. 5.2.2 |
| 5.2.2 and Table 1
Fig. 1(Dimensions - Thickness of Cuff) |
- |
0 |
|
Charges already taken in clause no. 5.2.2 |
| 5.3 and Table 2( Tensile Strength Before Ageing) |
- |
1350 |
|
Nil |
| 5.3 and Table 2( Elongation at Break Before Ageing) |
- |
0 |
|
Charges already taken in clause no. 5.3 |
| 5.3 and Table 2(Stress at 500% Elongation at Break Before Ageing) |
- |
5300 |
|
Test charges Rs. 1100/- plus conditioning charges Rs. 4200/- (25% discount is not applicable in conditioning charges) |
| 5.3 and Table 2( Tensile StrengthAfter Accelerated Ageing) |
- |
0 |
|
Charges already taken in clause no. 5.3 |
| 5.3 and Table 2( Elongation at Break After Accelerated Ageing) |
- |
0 |
|
Charges already taken in clause no. 5.3 |
| 5.5(Airtight Test) |
- |
1300 |
|
Test charges Rs. 1000/- plus specimen charges Rs. 300/- (25% discount is not applicable in conditioning charges) |
|
31 Dec, 2026 |
-
Included w.e.f. 27-05-2022. |
| 12743 |
Matrix Test Labs
| 8138626
| IS 16046 : Part 1 (2018) |
Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes ” Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for Use in Portable Applications Part 1 Nickel Systems ( Second Revision ) |
- |
180000 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.2(Insulation and Wiring) |
- |
5000 |
|
10% discount to BIS |
| 7.1(Charging procedure for test purposes) |
- |
10000 |
|
10% discount to BIS |
| 7.2(Intended Use) |
- |
60000 |
|
10% discount to BIS |
| 7.3(Reasonably foreseeable misuse) |
- |
115000 |
|
10% discount to BIS |
| 8(Information for safety) |
- |
5000 |
|
10% discount to BIS |
| 9(Marking) |
- |
5000 |
|
10% discount to BIS |
| 10(Packaging) |
- |
5000 |
|
10% discount to BIS |
| 4(Parameter Measurement Tolerances) |
- |
0 |
|
- |
| 5(General Safety Considerations) |
- |
0 |
|
- |
| 5.1(General) |
- |
0 |
|
- |
| 5.3(Venting) |
- |
0 |
|
- |
| 5.4(Temperature, Voltage and Current Management) |
- |
0 |
|
- |
| 5.5(Terminal Contacts) |
- |
0 |
|
- |
| 5.6(Assembly of Cells into batteries) |
- |
0 |
|
- |
| 5.7(Quality Plan) |
- |
0 |
|
- |
| 8.2(Small Cell and battery safety information) |
- |
10000 |
|
- |
| 6(Tyoe Test amd Sample Size) |
- |
0 |
|
- |
| 8.1(General) |
- |
0 |
|
- |
| 9.1(Cell Marking) |
- |
5000 |
|
- |
| 9.2(Battery Marking) |
- |
5000 |
|
- |
| 9.3(Caution for ingestion of small cells and batteries) |
- |
0 |
|
- |
| 9.4(Other information) |
- |
0 |
|
- |
|
31 Dec, 2026 |
-
REVISED VERSION
Included w.e.f.
14.01.2019. |
| 12744 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 13487 (1992) |
Irrigation equipment - Emitters - Specification |
- |
4700 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 7.1(Construction and workmanship) |
- |
300 |
|
Nil |
| 7.2(Flow path in emitters) |
- |
300 |
|
Nil |
| 7.3.1(Resistance to Hydrostatic pressure) |
- |
1000 |
|
Nil |
| 7.3.2(Resistance to Hydrostatic pressure) |
- |
0 |
|
Charges already taken in clause no. 7.3.1 |
| 7.3.3(Resistance to Hydrostatic pressure) |
- |
0 |
|
Charges already taken in clause no. 7.3.1 |
| 7.4.1(Emitter Pull Out In-line emitters) |
- |
500 |
|
Nil |
| 7.4.2(Emitter Pull Out On-line emitters) |
- |
0 |
|
Charges already taken in clause no. 7.4.1 |
| 8.1.2(Uniformity of Emission Rate Unregulated emitters) |
- |
1000 |
|
Nil |
| 8.1.2(Uniformity of Emission Rate Unregulated emitters) |
- |
0 |
|
Charges already taken in clause no. 8.1.2 |
| 8.1.3(Uniformity of Emission Rate Regulated emitters) |
- |
0 |
|
Charges already taken in clause no. 8.1.2 |
| 8.1.3(Uniformity of Emission Rate Regulated emitters) |
- |
0 |
|
Charges already taken in clause no. 8.1.2 |
| 8.2.2(Emission rate as a function of inlet pressure Unregulated emitters) |
- |
1000 |
|
Nil |
| 8.2.3(Emission rate as a function of inlet pressure Regulated emitters) |
- |
0 |
|
Charges already taken in clause no. 8.2.2 |
| 8.3(Determination of Emitter Exponent) |
- |
600 |
|
Nil |
|
31 Dec, 2026 |
-
- |
| 12745 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 12818 (2010) |
Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision) |
- |
14725 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5(COLOUR) |
- |
250 |
|
Nil |
| 4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the
resin - Annex A ofIS 10151) |
- |
3000 |
|
Nil |
| 4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating ) |
- |
1100 |
|
Nil |
| 4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content ) |
- |
0 |
|
Nil |
| 7.1 and Table 1, 2, 3, & 4
Fig 1A & 1B(Nominal Diameter) |
- |
1500 |
|
Nil |
| 7.1 and Table 1, 2, 3, & 4
Fig 1A & 1B(Mean Outer Diameter of Pipe) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.1 and Table 1, 2, 3, & 4
Fig 1A & 1B(Outer Diameter at any point ) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.1 and Table 1, 2, 3, & 4
Fig 1A & 1B(Mean Outer Diameter over Connection) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.1 and Table 1, 2, 3, & 4
Fig 1A & 1B(Wall thickness) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.2 and Table 5, 6 & 7
Fig 1B(DIMENSIONS - Casing Pipes) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.2 and Table 5, 6 & 7
Fig 1B(Nominal Diameter) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.2 and Table 5, 6 & 7
Fig 1B(Mean Outer Diameter of Pipe, Min) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.2 and Table 5, 6 & 7
Fig 1B(Mean Outer Diameter of Pipe , Max) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported)) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.2 and Table 5, 6 & 7
Fig 1B(Wall thickness, Min) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.2 and Table 5, 6 & 7
Fig 1B(Wall thickness, Max) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.3.1(No.of Ribs) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.3.2(Rib height) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.4 Table 8 & 9
Fig 1(Effective length, l2) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.4 Table 8 & 9
Fig 1(Segmental length, l3) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0)) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0)) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.5 and Table 10
Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.5 and Table 10
Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 7.5 and Table 10
Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w)) |
- |
0 |
|
Charges already taken in clause no. 7.1 Table 1 |
| 8.4(Sealing rings - Hardness) |
- |
375 |
|
Nil |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
250 |
|
Nil |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
0 |
|
Charges already taken in clause no. 8.4.1 |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
0 |
|
Charges already taken in clause no. 8.4.1 |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
0 |
|
Charges already taken in clause no. 8.4.1 |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
0 |
|
Charges already taken in clause no. 8.4.1 |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
0 |
|
Charges already taken in clause no. 8.4.1 |
| 8.4.1 and Table 13
Fig 3B & 4B(Dimensions of sealing elements) |
- |
0 |
|
Charges already taken in clause no. 8.4.1 |
| 9.1(Visual Appearance) |
- |
300 |
|
Nil |
| 9.1( Visual Appearance) |
- |
0 |
|
Charges already taken in clause no. 9.1 |
| 9.2(Internal Diameter) |
- |
350 |
|
Nil |
| 9.3(Density
IS 12235 (Part 14)) |
- |
500 |
|
Nil |
| 9.4 and Table 14(Resistance to External Blows at 0 ?C
IS 12235 (Part 9)) |
- |
1400 |
|
Test charges Rs. 1100/- plus specimen charges Rs. 300/- (25% discount is not applicable in specimen charges) |
| 9.5(Tensile Strength
IS 12235(Part 13)) |
- |
1600 |
|
Test charges Rs. 1100/- plus specimen charges Rs. 500/- (25% discount is not applicable in specimen charges) |
| 9.6(Vicat Softening Temperature
IS 12235 (Part 2).) |
- |
1100 |
|
Nil |
|
31 Dec, 2026 |
-
- |
| 12746 |
CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING AND TECHNOLOGY (CIPET):CSTS-BHOPAL
| 8100534
| IS 12786 (1989) |
Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification |
- |
9725.00 View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4.1.c.i (Density) |
- |
0 |
|
- |
| 4.1.c.iii (Volatile matter - Annex B ) |
- |
0 |
|
- |
| 4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963) |
- |
925 |
|
Nil |
| 4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963) |
- |
700 |
|
Nil |
| 7.3(Tensile Test) |
- |
1350 |
|
Test Charges Rs. 1100/- + Specimen charges Rs. 250/- |
| 7.3(Elongation at Break) |
- |
0 |
|
Charges already taken in tensile test (Clause no. 7.3) |
| 7.4(SusceptibiIity to Environmental Stress
Cracking) |
- |
1200 |
|
Nil |
| 5 and Table 1(DIMENSIONS OF PIPES - outside diameters) |
- |
250 |
|
- |
| 5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall) |
- |
0 |
|
Charges already taken in clause 5 and table 1 (DIMENSIONS OF PIPES - outside diameters) |
| 6.1(Visual Appearance) |
- |
300 |
|
- |
| 7.1(Hydraulic Characteristics) |
- |
3000 |
|
Quality test |
| 7.1(Hydraulic Characteristics) |
- |
1000 |
|
acceptance test |
| 7.2(Reversion Test) |
- |
1000 |
|
Testing charge 700.00+ specimen charge 300.00 |
| 5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall) |
- |
0 |
|
- |
|
31 Dec, 2026 |
-
EXCLUSION: Antioxidant test (Cl.4.1) |
| 12747 |
BIS, Central Laboratory (CL)
| None
| IS 14494 (2019) |
Elastomer insulated flexible cables for use in mines - Specification (First Revision) |
- |
- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 4 (CONDUCTOR) |
- |
|
|
|
| 5 (INSULATION) |
- |
|
|
|
| 5.1 (Power Cores) |
- |
|
|
|
| 5.2 (Pilot and Earth Cores) |
- |
|
|
|
| 7.1 (TAPE : Proofed Tape) |
- |
|
|
|
| 7.2 (TAPE : Polyethylene Terephalate (PETP) or
Polypropylene Base Tape) |
- |
|
|
|
| 7.3 (TAPE ) |
- |
|
|
|
| 8 (CENTRE) |
- |
|
|
|
| 9.1 (FILLERS) |
- |
|
|
|
| 9.2 (FILLERS) |
- |
|
|
|
| 10 (CRADLE SEPARATOR) |
- |
|
|
|
| 11.1 (ARMOUR) |
- |
|
|
|
| 11.2 a) (ARMOURING: Tensile Strength) |
- |
|
|
|
| 11.2 b) (ARMOURING: Elongation ) |
- |
|
|
|
| 11.2 c) (ARMOURING: Torsion Test (For round wire ) ) |
- |
|
|
|
| 11.2 d) (ARMOURING: Uniformity of zinc coating) |
- |
|
|
|
| 11.2 e) (ARMOURING: Mass of zinc coating ) |
- |
|
|
|
| 12.1 (SHEATH : Inner Sheath) |
- |
|
|
|
| 12.2 (SHEATH : Outer Sheath) |
- |
|
|
|
| 13.1 (REINFORCEMENT MATERIAL : Tape) |
- |
|
|
|
| 14.1 (CONSTRUCTION : CONDUCTOR) |
- |
|
|
|
| 14.2 (CONSTRUCTION : CONDUCTOR) |
- |
|
|
|
| 14.3 (CONSTRUCTION : CONDUCTOR) |
- |
|
|
|
| 16.1 (INSULATION) |
- |
|
|
|
| 16.2 (INSULATION : Thickness of Insulation) |
- |
|
|
|
| 16.3 (INSULATION : Tolerance on Insulation Thickness) |
- |
|
|
|
| 16.4 (INSULATION : Application of Insulation) |
- |
|
|
|
| 16.5 (INSULATION) |
- |
|
|
|
| 18 (PROTECTIVE SCREEN) |
- |
|
|
|
| 19 (CONDUCTANCE OF SCREEN) |
- |
|
|
|
| 19.1 (Individual Core Screen) |
- |
|
|
|
| 19.2 (Collective Screen) |
- |
|
|
|
| 20.1 (CORE IDENTIFICATION) |
- |
|
|
|
| 20.2 (Colour Scheme for Identification) |
- |
|
|
|
| 20.3 (Scheme for Identification by Numbering) |
- |
|
|
|
| 21.1 (LAYING UP OF CORES) |
- |
|
|
|
| 21.2 (LAYING UP OF CORES) |
- |
|
|
|
| 21.3 (LAYING UP OF CORES) |
- |
|
|
|
| 21.4 (LAYING UP OF CORES) |
- |
|
|
|
| 22.1 (INNER SHEATH) |
- |
|
|
|
| 22.2 (Thickness of Inner Sheath) |
- |
|
|
|
| 22.3 (INNER SHEATH) |
- |
|
|
|
| 23.1 (ARMOURING) |
- |
|
|
|
| 23.2 (ARMOURING) |
- |
|
|
|
| 23.3 (ARMOURING) |
- |
|
|
|
| 23.4 (ARMOURING) |
- |
|
|
|
| 24.1 (OUTER SHEATH) |
- |
|
|
|
| 24.2 (Thickness of Outer Sheath) |
- |
|
|
|
| 24.3 (Tolerance on Thickness of Outer Sheath) |
- |
|
|
|
| 24.4 (OUTER SHEATH) |
- |
|
|
|
| 25.1 (CABLE CONSTRUCTION AND DIMENSIONS) |
- |
|
|
|
| 27.8 (Flammability Test) |
- |
|
|
|
|
- |
-
EXCLUDING Ozone resistance test, dielectric pf test, Water Absorption Test, Heating cycle and partial discharge Test, High Voltage; |
| 12748 |
BIS, Central Laboratory (CL)
| None
| IS 14845 (2000) |
Resilient seated cast iron air relief valves for water works purposes - specification |
- |
4659 View breakup
Testing charges =15.5 x 300 + 1 x 9 = Rs. 4659.00 + testing charges as per relevant ISS.
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| (Cl 3)&(Cl5) (Type & Nom Size) |
- |
|
|
|
| (Cl 3)&(Cl5) (Type & Nom Size) |
- |
|
|
|
| (Cl 3)&(Cl5) (Type & Nom Size) |
- |
|
|
|
| (Cl 4) (Nom.Pressures) |
- |
|
|
|
| (Cl 8) (End Connection) |
- |
|
|
|
| (Cl.14) (Coating) |
- |
|
|
|
| (Cl10.6) (Nut & Bolts) |
- |
|
|
|
| (Cl.11) (Finish) |
- |
|
|
|
|
- |
-
Since the composition of cast iron shall be left to the discretion ofthe manufacturer , as such element to be tested with specified requirement and tolerances if any may please be declared with method of testing. Sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm.;
EXCLUDING all except IS 318 : 1974, IS 320 : 1980; End Connection (Cl.8) for screwed connection, (Cl.12 )Testing and performance, |
| 12749 |
BIS, Central Laboratory (CL)
| None
| IS 7142 (1995) |
Welded low carbon steel cylinders for low pressure liquifiable gases not exceeding 5 litre water capacity - Specification (First Revision) |
- |
Rs. 9552/- View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 13 (CHECKING OF WATER CAPACITY) |
- |
|
|
|
| 14.1.1 (PROOF TEST) |
- |
|
|
|
| 15.1 (PNEUMATIC LEAKAGE TEST) |
- |
|
|
|
| 16.2 ( Bursting Test) |
- |
|
|
|
| 17.3 i) (Acceptance test Parent Metal Longitudinal test specimen;) |
- |
|
|
|
| 17.3 ii) (Acceptance test Parent Metal Longitudinal test specimen;) |
- |
|
|
|
| 17.3 iii) (Acceptance test Parent Metal Longitudinal test specimen;) |
- |
|
|
|
| 17.3 iv) (Acceptance test Parent Metal Circumferential test specimen;) |
- |
|
|
|
| 17.3 v) (Acceptance test Parent Metal Circumferential test specimen;) |
- |
|
|
|
| 17.3 vi) (Acceptance test Parent Metal Circumferential test specimen;) |
- |
|
|
|
| 17.3 vii) (Acceptance test Weld joint test Specimen) |
- |
|
|
|
| 17.4 (Bend test across weld) |
- |
|
|
|
| 17.5 (Macro-examination) |
- |
|
|
|
| 17.6 (Minimum Thickness Test) |
- |
|
|
|
| 10.3 (Bung) |
- |
|
|
|
| 10.1 (FITTINGS OTHER THAN VALVES) |
- |
|
|
|
| 10.2 ii) (FITTINGS OTHER THAN VALVES) |
- |
|
|
|
| 10.2 iii) (FITTINGS OTHER THAN VALVES) |
- |
|
|
|
| 19 (COLOUR IDENTIFICATION) |
- |
|
|
|
| 9.1 (VALVES AND VALVES PAD) |
- |
|
|
|
|
- |
-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;
EXCLUDING "-; 16.1 Hydrostatic Stretch Test 10.3 Bung" |
| 12750 |
BIS, Central Laboratory (CL)
| None
| IS 15905 (2011) |
Hubless centrifugally cast (Spun) iron pipes, fittings and accessories - Spigot series - Specification |
- |
Rs. 5745/ View breakup
-
| Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
| 5.3 (Hardness ) |
- |
|
|
|
| 7.1 (Visual Inspection and Hammer Test) |
- |
|
|
|
| 8.1 (Crushing Strength ) |
- |
|
|
|
| 9.1 (Hydraustatic Test) |
- |
|
|
|
| 10.1 (External Diameter) |
- |
|
|
|
| 10.2, Table 3, Sl no. I to IV (Pipe Thickness) |
- |
|
|
|
| 10.2 , Table 3, Sl no. I to IV (Fittings Thickness) |
- |
|
|
|
| 10.3 (Length) |
- |
|
|
|
| 10.5 (Masses) |
- |
|
|
|
| 11.2.1, 11.2.2, Table 4 and 5, Sl no. Ito V (Nominal Size (DN)) |
- |
|
|
|
| 11.2.1, 11.2.2, Table 4 and 5, Sl no. I to V (a) |
- |
|
|
|
| 11.2.3, Table 6, Sl no. I to IV (Nominal Size (DN 1)) |
- |
|
|
|
| 11.2.3, Table 6, Sl no. I to IV (a) |
- |
|
|
|
| 11.2.3, Table 6, Sl no. I to IV (r) |
- |
|
|
|
| 11.2.4, Table 7, Sl no. I to V (Nominal Size (DN 1)) |
- |
|
|
|
| 11.2.4, Table 7, Sl no. I to V (a) |
- |
|
|
|
| 11.2.4, Table 7, Sl no. I to V (b) |
- |
|
|
|
| 11.2.5, Table 8, Sl no. I to II (Nominal Size (DN 1)) |
- |
|
|
|
| 11.2.5, Table 8, Sl no. I to II (Nominal Size (DN 2)) |
- |
|
|
|
| 11.2.5, Table 8, Sl no. I to II (a) |
- |
|
|
|
| 11.2.5, Table 8, Sl no. I to II (r) |
- |
|
|
|
| 11.2.5, Table 8, Sl no. I to II (b) |
- |
|
|
|
| 11.2.5, Table 8, Sl no. I to II (c ) |
- |
|
|
|
| 11.2.5, Table 8, Sl no. I to II (d) |
- |
|
|
|
| 11.2.6, Table 9, Sl no. I to II (Nominal Size (DN )) |
- |
|
|
|
| 11.2.6, Table 9, Sl no. I to II (a) |
- |
|
|
|
| 11.2.6, Table 9, Sl no. I to II (b) |
- |
|
|
|
| 11.2.6, Table 9, Sl no. I to II (c) |
- |
|
|
|
| 11.2.6, Table 9, Sl no. I to II (r) |
- |
|
|
|
| 11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (Nominal Size (DN 1)) |
- |
|
|
|
| 11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (Nominal Size (DN 2)) |
- |
|
|
|
| 11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (L) |
- |
|
|
|
| 11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (a) |
- |
|
|
|
| 11.2.7, 11.2.8, 11.2.9, 11.2.10 Table 10,11,12 & 13 (b) |
- |
|
|
|
| 11.2.11, Table 14, (Nominal Size (DN 1)) |
- |
|
|
|
| 11.2.11, Table 14, (Nominal Size (DN 2)) |
- |
|
|
|
| 11.2.11, Table 14, ( L) |
- |
|
|
|
| 11.2.12, Table 15 (Nominal Size (DN )) |
- |
|
|
|
| 11.2.12, Table 15 (L) |
- |
|
|
|
| 11.2.12, Table 15 (a) |
- |
|
|
|
| 5.1 (shall conform to FG 150 grade,appropriate, specified in IS 210.) |
- |
|
|
|
|
- |
-
Since the composition of cast iron shall be left to the discretion ofthe manufacturer , as such element to be tested with specified requirement and tolerances if any may please be declared with method of testing. Sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm.;
EXCLUDING -; hydraulic test |
