BIS - LIMS (Laboratory Information Management System)

National Test House (NR) - NTH, Ghaziabad

Kamla Nehru Nagar,Ghaziabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

9999472699 nthnr-ca@nic.in

Scope List

Reset

78 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 15769 (2008)

Flux cored (Tubular) electrodes for gas shielded and self - Shielded metal welding of carbon or carbon - Manganese steel

All

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Radiographic Soundness Test)	-	1000	Complete Testing Charges.
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	3000	Complete Testing Charges.
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	3000	Complete Testing Charges.
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	3000	Complete Testing Charges.
5.6(Longitudinal Bend Test)	-	8000	Complete Testing Charges.
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	5000	Complete Testing Charges.
5.8 (Table No.- 15)(Chemical Composition,%)	-	5000	Complete Testing Charges.
5.2(Radiographic Soundness Test)	-	0	Duplicate clause
5.3 (Table No.- 1)(Tensile Test(T.S., Y.S. & El), Mpa-IS 1608)	-	0	Duplicate clause
5.4 (Table No.- 2)(Impact Test,J- IS 1757)	-	0	Duplicate clause
5.5 (Table No.- 1)(Transverse Tensile Test,Mpa (T.S., Y.S. & El))	-	0	Duplicate clause
5.6(Longitudinal Bend Test)	-	0	Duplicate clause
5.7(Diffusible Hydrogen Test,ml/100g- IS 11802)	-	0	Duplicate clause
5.8 (Table No.- 15)(Chemical Composition,%)	-	0	Duplicate clause

26 Oct, 2025

-
-

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

All Types/Grades

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.2, Table- 1 (i)(Blister)	-	100	-
Cl-5.2, Table- 1 (ii)(Checks)	-	100	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	100	-
Cl-5.2, Table- 1 (iv)(Dote)	-	100	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	100	-
Cl-5.2, Table- 1 (vi)(Joints)	-	100	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	100	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	100	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	100	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	100	-
Cl-5.2, Table- 1 (xi)(Patches)	-	100	-
Cl-5.2, Table- 1 (xii)(Splits)	-	100	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	100	-
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	500	-
Cl.5.2(Quality Requirements of Plywood for General Purposes)	-	500	-
Cl-9(WORKMANSHIP AND FINISH)	-	200	-
Cl-8.1(Dimensions -length)	-	300	-
Cl.8.1(Dimensions -width)	-	300	-
Cl-8.2(Thickness of the plywood boards)	-	400	-
Cl-8.3(Squareness)	-	250	-
Cl.8, 8.3 & Annex C(Edge Squareness)	-	250	-
Cl.8, 8.3 & Annex C(Edge Straightness)	-	250	-
Cl-11.4(Moisture Content)	-	1000	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	3000	-
Cl-11.3.2(Mycological Test)	-	1500	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	0	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	1000	-
Cl-11.5, Table-4,(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	0	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	1000	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	0	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	1000	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	0	-
Cl-11.6(Formaldehyde Content Test)	-	2500	-
Cl-5.1(Classification by appearance)	-	250	-

26 Oct, 2025

-
Included w.e.f 28.11.2025 Cl-11.7 (Steady-State Formaldehyde Emission Test)

IS 1475 (2024)

Drinking Water Coolers - Specification (Fourth Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	0	-
5(Construction)	-	0	-
6.3(Cooling Capacity Test)	-	5000	-
6.4(Maximum Operating Condition Test)	-	4999.98	-
6.5(Pull Down Test)	-	5000	-
9(Maximum Power Consumption Test)	-	2500	-
10(Annual Energy Consumption Test)	-	2500	-
11(Storage Capacity Test)	-	500	-
13(Functional Test)	-	2000.03	-
14 a)(Protection against electric shock)	-	1500	-
14 b)(High voltage (electric strength) test)	-	2500	-
14 c)(Leakage current tests)	-	2000	-
14 d)(Provision for earthing)	-	1000	-
4(Classification)	-	0	-
5(Construction)	-	0	-
6.3(Cooling Capacity Test)	-	0	-
6.4(Maximum Operating Condition Test)	-	0	-
6.5(Pull Down Test)	-	0	-
9(Maximum Power Consumption Test)	-	0	-
10(Annual Energy Consumption Test)	-	0	-
11(Storage Capacity Test)	-	0	-
13(Functional Test)	-	0	-
14 a)(Protection against electric shock)	-	0	-
14 b)(High voltage (electric strength) test)	-	0	-
14 c)(Leakage current tests)	-	0	-
14 d)(Provision for earthing)	-	0	-

26 Oct, 2025

-
included w.e.f 11-12-2025.

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	250	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	250	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	250	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	250	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	250	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Lower)	-	250	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Higher)	-	250	-
Clause 7.1.1 (General Quality)	-	500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	4000	-
Clause 7.1.3 (Colour and Texture)	-	500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	250	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	250	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	250	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	250	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	250	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Lower)	-	250	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Higher)	-	250	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	250	-

26 Oct, 2025

-
-

IS 13995 (1995)

Unlined moulded rubber boots - Specification

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.7(Size)	-	500	-
5.1.6(Design)	-	500	-
5.1.5(Flexing resistance of upper)	-	500	-
5.1.4(Resistance to dry heat ageing )	-	500	-
5.1.3(Tear Strength)	-	500	-
5.1.2(Tensile Strength (after ageing))	-	500	-
5.1.1(Tensile Strength (before ageing))	-	500	-
4.1(Thickness )	-	500	-
6, 6.1(Marking)	-	500	-
Cl.6, 6.1(Marking)	-	500	-
5.1.7(Size)	-	500	-
5.1.6(Design)	-	500	-
5.1.5(Flexing resistance of upper)	-	500	-
5.1.4(Resistance to dry heat ageing )	-	500	-
5.1.3(Tear Strength)	-	500	-
5.1.2(Tensile Strength (after ageing))	-	500	-
5.1.1(Tensile Strength (before ageing))	-	500	-
4.1(Thickness )	-	500	-
6, 6.1(Marking)	-	500	-
Cl.6, 6.1(Marking)	-	500	-

26 Oct, 2025

-
Included w.e.f.09.10.2025

IS 13893 (1994)

Polyurethane soles semirigid - specification

10000 View breakup
-

Clause No.	Exclusion	Remark
4.3.2(Ageing test)	-	-
4.3(Ross Flex test)	-	-
4.3(Flexural strength )	-	-
4.3(Abrasion Resistance)	-	-
4.3(Elongation at break)	-	-
4.3(Hardness Shore(A))	-	-
4.3(Relative density )	-	-
4.2(Thickness )	-	-
4.2 (Amendment 2)(Thickness)	-	-
4.1(Design)	-	-
5, 5.1, 5.2(Packing And Marking)	-	-
Cl.5, 5.1, 5.2(Packing And Marking)	-	-
4.3.1 Table 1 i) (Amendment 2)(Relative Density)	-	-
4.3.1 Table 1 iii) (Amendment 2)(Abrasion Resistance at applied force of 10 N)	-	-
4.3.1 Table 1 iv) (Amendment 2)(Flexing Resistance, Bennewart method)	-	-
4.3.1 Table 1 v) (Amendment 2)(Hydrolysis Resistance, cut growth after 150000 flexes)	-	-
4.3.1 Table 1 vi) (Amendment 2)(Tensile Strength)	-	-
4.3.1 Table 1 vii) (Amendment 2)(Elongation at break)	-	-
4.3.1 Table 1 viii) (Amendment 2)(Tear Strength (average force))	-	-
4.3.1 Table 1 ii) (Amendment 2)(Hardness, degree, Shore A)	-	-
4.3(Tensile Strength )	-	-

26 Oct, 2025

-
Included w.e.f.09.10.2025

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Remark
4.2(Flexing resistance )	-	-
4.2(Water absorption)	-	-
4.2(Heat Shrinkage )	-	-
4.2(Shrinkage at room temp)	-	-
4.2(Split tear strength)	-	-
4.2(Compression set)	-	-
4.2(Hardness (Shore A))	-	-
4.2(Density )	-	-
4.2(Size & Thickness )	-	-
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	-
Cl.4.1.3 And 8.3,Table1, iii)(Hardness, Shore A durometer min)	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi)(Heat shrinkage test at 100±1°C for 1 hour max)	-	-
Cl.4 Cl.4.1.3 And 8.3,Table1, viii)(Water absorption , percent by mass, Max)	-	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii)(Flexing resistance: Maximum cut growth at 50 000 cycles)	-	-
5, 5.1(Marking)	-	-
6, 6.1(Packing)	-	-
"Cl.4 ,Cl.4.1,4.1.1,4.1.2(Requirements ")	-	-
Cl.4.1.3 And 8.3,Table1(i) Relative density)	-	-
Cl.4.1.3 And 8.3,Table1(ii) Hardness, Shore A durometer min)	-	-
Cl.4.1.3 And 8.3,Table1(iii) Change in Hardness after ageing at 100±1°C for 24hr)	-	-
Cl.4.1.3 And 8.3,Table1(iv) Compression set at constant stress percent, Max)	-	-
Cl.4.1.3 And 8.3,Table1(vi) Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	-
Cl.4.1.3 And 8.3,Table 1 vi(Heat shrinkage test at 100±1°C for 1 hour max)	-	-
Cl.4.1.3 And 8.3,Table1(viii)Water absorption , percent by mass, Max)	-	-
Cl.4.1.3 And 8.3,Table1(ix)Flexing resistance)	-	-
5, 5.1(Marking)	-	-
6, 6.1(Packing)	-	-
Cl.4.1.3 and 8.3,Table 1 ii(Thickness)	-	-
Cl.4.1.3 and 8.3,Table 1 vii(Abrasion resistance at applied force of 5 N)	-	-

26 Oct, 2025

-
Included w.e.f.09.10.2025

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

20000 View breakup
-

Clause No.	Exclusion	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	-
5/5.1(REQUIREMENTS-General)	-	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	-
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	-
5/5.1(REQUIREMENTS-General)	-	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	-
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	-
5/5.1(REQUIREMENTS-General)	-	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	-
6(Marking and packing)	-	-
8.1(Test methods)	-	-
Cl.8.3(Measurement of thickness ")	-	-
5.5 (Amendment 1)(Thickness)	-	-
5.7 Table 2 i) (Amendment 1)(Relative Density)	-	-
5.7, Table 2 ii) (Amendment 1)(Hardness, degree, Shore A)	-	-
5.7, Table 2 iv) (Amendment 1)(Abrasion Resistance at applied force of 10 N)	-	-
5.7, Table 2 v) (Amendment 1)(Tensile strength)	-	-
5.7, Table 2 vi) (Amendment 1)(Elongation at break)	-	-
5.7, Table 2 vii) (Amendment 1)(Tear strength (average force))	-	-
5.7, Table 2 iii) (Amendment 1)(Flexing resistance)	-	-
8.3(Measurement of thickness)	-	-
Cl.6.1,6.2,6.3(Marking and packing)	-	-
8.1(Test Methods)	-	-

26 Oct, 2025

-
Included w.e.f.11.09.2025

IS 15298 : Part 3 (2024)

Personal Protective Equipment Part 3 Protective Footwear (ISO 20346 : 2021, MOD) (Third Revision)

40000 View breakup
-

Clause No.	Exclusion	Remark
Cl 5.2(Design)	-	-
Cl 5.2.2(" Height of upper ")	-	-
Cl 5.2.3(Heel area)	-	-
Cl 5.3.1.1(Construction of whole footwear)	-	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	-
Cl 5.3.2.1(Toe protection - general)	-	-
Cl 5.3.2.2(Internal length)	-	-
Cl 5.3.2.3(Width of toecap flange)	-	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	-
Cl 5.3.2.6(Impact resistance)	-	-
Cl 5.3.2.7(Compression resistance)	-	-
Cl 5.3.3(Leak proofness)	-	-
Cl 5.3.4("Specific ergonomic features ")	-	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	-
Cl 5.3.7(Seam strength)	-	-
Cl 5.3.8(Lead Content ( National Annex A))	-	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	-
Cl 5.4.2(Thickness)	-	-
Cl 5.4.3(Tear strength)	-	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	-
Cl 5.4.7(Resistance to hydrolysis)	-	-
Cl 5.5.2(Lining- Tear strength)	-	-
Cl 5.5.3(Lining- Abrasion resistance)	-	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	-
Cl 5.6.2(Tear strength of tongue)	-	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	-
Cl 5.7.2(Water permeability of insock)	-	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	-
Cl 5.8.2.1(Thickness of Outsole)	-	-
Cl 5.8.2.2(Cleated area)	-	-
Cl 5.8.2.3(Cleat height)	-	-
Cl 5.8.3(Outsole- Tear strength)	-	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	-
Cl 5.8.5(Outsole-Flexing resistance)	-	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	-
Cl 5.8.7(Interlayer bond strength)	-	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	-
Cl 6.2.4(Energy absorption of seat region)	-	-
Cl 6.2.5(Water resistance)	-	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	-
Cl 6.2.7(Ankle protection)	-	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	-
Cl 6.2.8.3(Resistance to cutting)	-	-
Cl 6.2.9(Scuff cap)	-	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	-
Cl 6.3(Upper — Water penetration and absorption)	-	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	-
Cl 6.4.3.2(Design of Ladder grip)	-	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	-
Cl 7("Marking ")	-	-
Cl 7("Marking ")	-	-
Cl 5.4.5(Flexing resistance)	-	-
Cl 5.2(Design)	-	-
Cl 5.2.2(" Height of upper ")	-	-
Cl 5.2.3(Heel area)	-	-
Cl 5.3.1.1(Construction of whole footwear)	-	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	-
Cl 5.3.2.1(Toe protection - general)	-	-
Cl 5.3.2.2(Internal length)	-	-
Cl 5.3.2.3(Width of toecap flange)	-	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	-
Cl 5.3.2.6(Impact resistance)	-	-
Cl 5.3.2.7(Compression resistance)	-	-
Cl 5.3.3(Leak proofness)	-	-
Cl 5.3.4("Specific ergonomic features ")	-	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	-
Cl 5.3.7(Seam strength)	-	-
Cl 5.3.8(Lead Content ( National Annex A))	-	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	-
Cl 5.4.2(Thickness)	-	-
Cl 5.4.3(Tear strength)	-	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	-
Cl 5.4.7(Resistance to hydrolysis)	-	-
Cl 5.5.2(Lining- Tear strength)	-	-
Cl 5.5.3(Lining- Abrasion resistance)	-	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	-
Cl 5.6.2(Tear strength of tongue)	-	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	-
Cl 5.7.2(Water permeability of insock)	-	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	-
Cl 5.8.2.1(Thickness of Outsole)	-	-
Cl 5.8.2.2(Cleated area)	-	-
Cl 5.8.2.3(Cleat height)	-	-
Cl 5.8.3(Outsole- Tear strength)	-	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	-
Cl 5.8.5(Outsole-Flexing resistance)	-	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	-
Cl 5.8.7(Interlayer bond strength)	-	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	-
Cl 6.2.4(Energy absorption of seat region)	-	-
Cl 6.2.5(Water resistance)	-	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	-
Cl 6.2.7(Ankle protection)	-	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	-
Cl 6.2.8.3(Resistance to cutting)	-	-
Cl 6.2.9(Scuff cap)	-	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	-
Cl 6.3(Upper — Water penetration and absorption)	-	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	-
Cl 6.4.3.2(Design of Ladder grip)	-	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	-
Cl 7("Marking ")	-	-
Cl 7("Marking ")	-	-
Cl 5.4.5(Flexing resistance)	-	-

26 Oct, 2025

-
Included w.e.f.11.09.2025 Exclusion :Cl 5.3.6, Table no 1 of IS 17011 (i) (Allergenic and carcinogenic disperse dyes) Cl 5.3.6, Table no 1 of IS 17011 (ii) (Aromatic amines released from Azo dyes (each individual amine)) Cl 5.3.6, Table no 1 of IS 17011 (iii) (Aromatic amines released from Azo dyes (each individual amine)) Cl 5.3.6, Table no 1 of IS 17011 (iv) (Chromium (VI)) Cl 5.3.6, Table no 1 of IS 17011 (v) (Dimethyl fumarate (DMFU)) Cl 5.3.6, Table no1 of IS 17011 (vi) (Formaldehyde (free or released by partial hydrolysis)) Cl 5.3.6, Table no 1 of IS 17011 (vii) (Formaldehyde) Cl 5.3.6, Table no 1 of IS 17011 (viii) (Organotin compounds) Cl 5.3.6, Table no 1 of IS 17011 (ix) (PCP-TeCP-TriCP polychlorophenols) Cl 5.3.6, Table no 1 of IS 17011 (xi) (Phthalates (each individual phthalate))

IS 11544 (1986)

Specification for slipper, rubber

12000 View breakup
-

Clause No.	Exclusion	Remark
3.2.6(Thickness of components)	-	-
3.2.5(Type of Thread)	-	-
3.2.4(Colour fasntess to washing)	-	-
3.2.4(Picks per cm)	-	-
3.2.4(End per cm)	-	-
3.2.4(Mass per unit area)	-	-
3.2(Flexural endurance)	-	-
3.2(Hardness after ageing)	-	-
3.2(Relative density )	-	-
3.1(Shape & Design)	-	-
3.2.2(Bottom Filling Material)	-	-
3.2.4.1(Weave of fabrics)	-	-
3.2.7(vulcanized process)	-	-
3.2.8(Workmanship and Finish -)	-	-
3.2.9(Preservation -)	-	-
Cl. 4, Cl. 4.1, Cl 4.2, Cl. 4.3(Marking and packing)	-	-
Cl. 4, Cl. 4.1,Cl 4.2(Marking and packing)	-	-
3.2(Hardness (IRHD))	-	-

26 Oct, 2025

-
Included w.e.f.18.08.2025

IS 6719 (1972)

Solid Pvc Soles And Heels

15000 View breakup
-

Clause No.	Exclusion	Remark
3.6.1(Hardness )	-	-
3.6 (vi)(Lead (as Pb) ppm)	-	-
3.6 (v)(Volatility, percent by means )	-	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	-
3.6 (iii)(Elongation at break, percent )	-	-
3.6 (ii)(Tensile Strength )	-	-
3.6 (i)(Relative density )	-	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	-
6 ,6.1,6.2,6.3(Test Method)	-	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	-
Cl. 6.4(Measurement of thickness)	-	-
Table 1 (Flexing resistance)(Table 1 (Flexing resistance, Bennewart method, cut growth at the end of 30 000 cycles, mm, Max))	-	-
Table 1 (Abrasion resistance)(Abrasion resistance at applied force of 10 N (volume loss), mm3, Max)	-	-
Table 1 Cl. 3.6, Sl No (iii)(Volatility, Percent by mass)	-	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), Shoes for infants, children and boys and girls, ppm")	-	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), for other sized shoes, ppm ")	-	-
3.6.1(Hardness )	-	-
3.6 (vi)(Lead (as Pb) ppm)	-	-
3.6 (v)(Volatility, percent by means )	-	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	-
3.6 (iii)(Elongation at break, percent )	-	-
3.6 (ii)(Tensile Strength )	-	-
3.6 (i)(Relative density )	-	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	-
6 ,6.1,6.2,6.3(Test Method)	-	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	-
Cl. 6.4(Measurement of thickness)	-	-
Table 1 (Flexing resistance)(Table 1 (Flexing resistance, Bennewart method, cut growth at the end of 30 000 cycles, mm, Max))	-	-
Table 1 (Abrasion resistance)(Abrasion resistance at applied force of 10 N (volume loss), mm3, Max)	-	-
Table 1 Cl. 3.6, Sl No (iii)(Volatility, Percent by mass)	-	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), Shoes for infants, children and boys and girls, ppm")	-	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), for other sized shoes, ppm ")	-	-
3.6.1(Hardness )	-	-
3.6 (vi)(Lead (as Pb) ppm)	-	-
3.6 (v)(Volatility, percent by means )	-	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	-
3.6 (iii)(Elongation at break, percent )	-	-
3.6 (ii)(Tensile Strength )	-	-
3.6 (i)(Relative density )	-	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	-
6 ,6.1,6.2,6.3(Test Method)	-	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	-
Cl. 6.4(Measurement of thickness)	-	-
Table 1 (Flexing resistance)(Table 1 (Flexing resistance, Bennewart method, cut growth at the end of 30 000 cycles, mm, Max))	-	-
Table 1 (Abrasion resistance)(Abrasion resistance at applied force of 10 N (volume loss), mm3, Max)	-	-
Table 1 Cl. 3.6, Sl No (iii)(Volatility, Percent by mass)	-	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), Shoes for infants, children and boys and girls, ppm")	-	-
Table 1 Cl. 3.6, Sl No (iv)("Lead (as Pb), for other sized shoes, ppm ")	-	-

26 Oct, 2025

-
Included w.e.f.18.08.2025

IS 5557 : Part 2 (2018)

All rubber gum boots and ankle boots: Part 2 occupational purposes

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CLASSIFICATION)	-	100	-
3.2(compact insole)	-	100	-
3.3(compact insole)	-	100	-
3.4(compact Outsole/heel)	-	0	-
3.5(Description lining material)	-	0	-
3.6(description occupatioanl footwear)	-	0	-
3.7(Ruber material)	-	0	-
4(Type & varity)	-	0	-
5(Design)	-	0	-
6(size & fitting)	-	0	-
7.1(lining material)	-	0	-
7.1.1(Tear strength)	-	500	-
7.1.2(Abrasion resistance)	-	2000	-
7.2(Coated bindind material)	-	2000	-
7.3(Thread for upper closing)	-	1000	-
7.3(Thread for upper closing - sulphur test)	-	1000	-
7.4(Use of rubber)	-	100	-
7.4.1(Physical requirement of rubber component)	-	1000	-
7.5(observation of Upper)	-	100	-
7.5.1(Tensile)	-	2000	-
7.5.2(Thickness)	-	500	-
7.5.3(Flexing Resistance)	-	2000	-
7.6(Outsole/Heel)	-	500	-
7.6.1(Out sole thickness)	-	500	-
7.6.2(out sole tear strength)	-	1000	-
7.6.3(out sole abrasion)	-	1000	-
7.6.4(out sole flexing)	-	1000	-
7.6.5(Interlayer bond strength)	-	1000	-
7.7(INSOCK Visual)	-	100	-
7.7.1(Insock thickness)	-	500	-
7.7.2(Insock abrasion)	-	1000	-
8(CONSTRUCTION)	-	500	-
8.1(Hot contact)	-	1000	-
8.2(Leak proofness)	-	1000	-
8.3(Height of upper)	-	500	-
8.4(Adhesion test)	-	2000	-
8.5(Resistance to acid & alkaline)	-	1000	-
8.6(Resistance to fule oil)	-	1000	-
8.7.1(Antistatic)	-	1000	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	500	-
8.7.3(Elecrically nsulating footwear)	-	1000	-
8.7.4(Resistance to cold)	-	500	-
10(Finish of boots)	-	100	-
11.1(Marking)	-	100	-
11.2(Marking)	-	100	-
11.3(Marking)	-	100	-
9(IS - 17011,Table - 1(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
cl 9(IS - 17011,Table - 1(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
9(IS - 17011,Table - 1(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
9(IS - 17011,Table - 1(iv)(Chromium (VI))	-	500	-
9(IS - 17011,Table - 1(v)(Dimethyl fumarate (DMFU))	-	0	-
9(IS - 17011,Table - 1(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
9(IS - 17011,Table - 1(vii)(Formaldehyde)	-	0	-
9(IS - 17011,Table - 1(viii)(Organotin compounds)	-	0	-
9(IS - 17011,Table - 1(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
9(IS - 17011,Table - 1(x)(pH)	-	0	-
9(IS - 17011,Table - 1(xi)(Phthalates (each individual phthalate))	-	0	-
9(IS - 17011,Table - 1(xii)(Nickel, on skin contact)	-	500	-
3.1(CLASSIFICATION)	-	0	-
3.2(compact insole)	-	0	-
3.3(compact insole)	-	0	-
3.4(compact Outsole/heel)	-	0	-
3.5(Description lining material)	-	0	-
3.6(description occupatioanl footwear)	-	0	-
3.7(Ruber material)	-	0	-
4(Type & varity)	-	0	-
5(Design)	-	0	-
6(size & fitting)	-	0	-
7.1(lining material)	-	0	-
7.1.1(Tear strength)	-	0	-
7.1.2(Abrasion resistance)	-	0	-
7.2(Coated bindind material)	-	0	-
7.3(Thread for upper closing)	-	0	-
7.3(Thread for upper closing - sulphur test)	-	0	-
7.4(Use of rubber)	-	0	-
7.4.1(Physical requirement of rubber component)	-	0	-
7.5(observation of Upper)	-	0	-
7.5.1(Tensile)	-	0	-
7.5.2(Thickness)	-	0	-
7.5.3(Flexing Resistance)	-	0	-
7.6(Outsole/Heel)	-	0	-
7.6.1(Out sole thickness)	-	0	-
7.6.2(out sole tear strength)	-	0	-
7.6.3(out sole abrasion)	-	0	-
7.6.4(out sole flexing)	-	0	-
7.6.5(Interlayer bond strength)	-	0	-
7.7(INSOCK Visual)	-	0	-
7.7.1(Insock thickness)	-	0	-
7.7.2(Insock abrasion)	-	0	-
8(CONSTRUCTION)	-	0	-
8.1(Hot contact)	-	0	-
8.2(Leak proofness)	-	0	-
8.3(Height of upper)	-	0	-
8.4(Adhesion test)	-	0	-
8.5(Resistance to acid & alkaline)	-	0	-
8.6(Resistance to fule oil)	-	0	-
8.7.1(Antistatic)	-	0	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	0	-
8.7.3(Elecrically nsulating footwear)	-	0	-
8.7.4(Resistance to cold)	-	0	-
10(Finish of boots)	-	0	-
11.1(Marking)	-	0	-
11.2(Marking)	-	0	-
11.3(Marking)	-	0	-
9(IS - 17011,Table - 1(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
cl 9(IS - 17011,Table - 1(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
9(IS - 17011,Table - 1(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
9(IS - 17011,Table - 1(iv)(Chromium (VI))	-	0	-
9(IS - 17011,Table - 1(v)(Dimethyl fumarate (DMFU))	-	0	-
9(IS - 17011,Table - 1(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
9(IS - 17011,Table - 1(vii)(Formaldehyde)	-	0	-
9(IS - 17011,Table - 1(viii)(Organotin compounds)	-	0	-
9(IS - 17011,Table - 1(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
9(IS - 17011,Table - 1(x)(pH)	-	0	-
9(IS - 17011,Table - 1(xi)(Phthalates (each individual phthalate))	-	0	-
9(IS - 17011,Table - 1(xii)(Nickel, on skin contact)	-	0	-
3.1(CLASSIFICATION)	-	0	-
3.2(compact insole)	-	0	-
3.3(compact insole)	-	0	-
3.4(compact Outsole/heel)	-	0	-
3.5(Description lining material)	-	0	-
3.6(description occupatioanl footwear)	-	0	-
3.7(Ruber material)	-	0	-
4(Type & varity)	-	0	-
5(Design)	-	0	-
6(size & fitting)	-	0	-
7.1(lining material)	-	0	-
7.1.1(Tear strength)	-	0	-
7.1.2(Abrasion resistance)	-	0	-
7.2(Coated bindind material)	-	0	-
7.3(Thread for upper closing)	-	0	-
7.3(Thread for upper closing - sulphur test)	-	0	-
7.4(Use of rubber)	-	0	-
7.4.1(Physical requirement of rubber component)	-	0	-
7.5(observation of Upper)	-	0	-
7.5.1(Tensile)	-	0	-
7.5.2(Thickness)	-	0	-
7.5.3(Flexing Resistance)	-	0	-
7.6(Outsole/Heel)	-	0	-
7.6.1(Out sole thickness)	-	0	-
7.6.2(out sole tear strength)	-	0	-
7.6.3(out sole abrasion)	-	0	-
7.6.4(out sole flexing)	-	0	-
7.6.5(Interlayer bond strength)	-	0	-
7.7(INSOCK Visual)	-	0	-
7.7.1(Insock thickness)	-	0	-
7.7.2(Insock abrasion)	-	0	-
8(CONSTRUCTION)	-	0	-
8.1(Hot contact)	-	0	-
8.2(Leak proofness)	-	0	-
8.3(Height of upper)	-	0	-
8.4(Adhesion test)	-	0	-
8.5(Resistance to acid & alkaline)	-	0	-
8.6(Resistance to fule oil)	-	0	-
8.7.1(Antistatic)	-	0	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	0	-
8.7.3(Elecrically nsulating footwear)	-	0	-
8.7.4(Resistance to cold)	-	0	-
10(Finish of boots)	-	0	-
11.1(Marking)	-	0	-
11.2(Marking)	-	0	-
11.3(Marking)	-	0	-
9(IS - 17011,Table - 1(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
cl 9(IS - 17011,Table - 1(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
9(IS - 17011,Table - 1(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
9(IS - 17011,Table - 1(iv)(Chromium (VI))	-	0	-
9(IS - 17011,Table - 1(v)(Dimethyl fumarate (DMFU))	-	0	-
9(IS - 17011,Table - 1(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
9(IS - 17011,Table - 1(vii)(Formaldehyde)	-	0	-
9(IS - 17011,Table - 1(viii)(Organotin compounds)	-	0	-
9(IS - 17011,Table - 1(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
9(IS - 17011,Table - 1(x)(pH)	-	0	-
9(IS - 17011,Table - 1(xi)(Phthalates (each individual phthalate))	-	0	-
9(IS - 17011,Table - 1(xii)(Nickel, on skin contact)	-	0	-
3.1(CLASSIFICATION)	-	0	-
3.2(compact insole)	-	0	-
3.3(compact insole)	-	0	-
3.4(compact Outsole/heel)	-	0	-
3.5(Description lining material)	-	0	-
3.6(description occupatioanl footwear)	-	0	-
3.7(Ruber material)	-	0	-
4(Type & varity)	-	0	-
5(Design)	-	0	-
6(size & fitting)	-	0	-
7.1(lining material)	-	0	-
7.1.1(Tear strength)	-	0	-
7.1.2(Abrasion resistance)	-	0	-
7.2(Coated bindind material)	-	0	-
7.3(Thread for upper closing)	-	0	-
7.3(Thread for upper closing - sulphur test)	-	0	-
7.4(Use of rubber)	-	0	-
7.4.1(Physical requirement of rubber component)	-	0	-
7.5(observation of Upper)	-	0	-
7.5.1(Tensile)	-	0	-
7.5.2(Thickness)	-	0	-
7.5.3(Flexing Resistance)	-	0	-
7.6(Outsole/Heel)	-	0	-
7.6.1(Out sole thickness)	-	0	-
7.6.2(out sole tear strength)	-	0	-
7.6.3(out sole abrasion)	-	0	-
7.6.4(out sole flexing)	-	0	-
7.6.5(Interlayer bond strength)	-	0	-
7.7(INSOCK Visual)	-	0	-
7.7.1(Insock thickness)	-	0	-
7.7.2(Insock abrasion)	-	0	-
8(CONSTRUCTION)	-	0	-
8.1(Hot contact)	-	0	-
8.2(Leak proofness)	-	0	-
8.3(Height of upper)	-	0	-
8.4(Adhesion test)	-	0	-
8.5(Resistance to acid & alkaline)	-	0	-
8.6(Resistance to fule oil)	-	0	-
8.7.1(Antistatic)	-	0	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	0	-
8.7.3(Elecrically nsulating footwear)	-	0	-
8.7.4(Resistance to cold)	-	0	-
10(Finish of boots)	-	0	-
11.1(Marking)	-	0	-
11.2(Marking)	-	0	-
11.3(Marking)	-	0	-
9(IS - 17011,Table - 1(iv)(Chromium (VI))	-	0	-
9(IS - 17011,Table - 1(x)(pH)	-	0	-
3.1(CLASSIFICATION)	-	0	-
3.2(compact insole)	-	0	-
3.3(compact insole)	-	0	-
3.4(compact Outsole/heel)	-	0	-
3.5(Description lining material)	-	0	-
3.6(description occupatioanl footwear)	-	0	-
3.7(Ruber material)	-	0	-
4(Type & varity)	-	0	-
5(Design)	-	0	-
6(size & fitting)	-	0	-
7.1(lining material)	-	0	-
7.1.1(Tear strength)	-	0	-
7.1.2(Abrasion resistance)	-	0	-
7.2(Coated bindind material)	-	0	-
7.3(Thread for upper closing)	-	0	-
7.3(Thread for upper closing - sulphur test)	-	0	-
7.4(Use of rubber)	-	0	-
7.4.1(Physical requirement of rubber component)	-	0	-
7.5(observation of Upper)	-	0	-
7.5.1(Tensile)	-	0	-
7.5.2(Thickness)	-	0	-
7.5.3(Flexing Resistance)	-	0	-
7.6(Outsole/Heel)	-	0	-
7.6.1(Out sole thickness)	-	0	-
7.6.2(out sole tear strength)	-	0	-
7.6.3(out sole abrasion)	-	0	-
7.6.4(out sole flexing)	-	0	-
7.6.5(Interlayer bond strength)	-	0	-
7.7(INSOCK Visual)	-	0	-
7.7.1(Insock thickness)	-	0	-
7.7.2(Insock abrasion)	-	0	-
8(CONSTRUCTION)	-	0	-
8.1(Hot contact)	-	0	-
8.2(Leak proofness)	-	0	-
8.3(Height of upper)	-	0	-
8.4(Adhesion test)	-	0	-
8.5(Resistance to acid & alkaline)	-	0	-
8.6(Resistance to fule oil)	-	0	-
8.7.1(Antistatic)	-	0	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	0	-
8.7.3(Elecrically nsulating footwear)	-	0	-
8.7.4(Resistance to cold)	-	0	-
10(Finish of boots)	-	0	-
11.1(Marking)	-	0	-
11.2(Marking)	-	0	-
11.3(Marking)	-	0	-
9(IS - 17011,Table - 1(iv)(Chromium (VI))	-	0	-
9(IS - 17011,Table - 1(x)(pH)	-	500	-

26 Oct, 2025

-
Included w.e.f.11.09.2025 Exclusion 9(IS - 17011,Table - 1(i) (Allergenic and carcinogenic disperse dyes) cl 9(IS - 17011,Table - 1(ii) (Aromatic amines released from Azo dyes (each individual amine)) 9(IS - 17011,Table - 1(iii) (Aromatic amines released from Azo dyes (each individual amine)) 9(IS - 17011,Table - 1(v) (Dimethyl fumarate (DMFU)) 9(IS - 17011,Table - 1(vi) (Formaldehyde (free or released by partial hydrolysis)) 9(IS - 17011,Table - 1(vii) (Formaldehyde) 9(IS - 17011,Table - 1(viii) (Organotin compounds) 9(IS - 17011,Table - 1(ix) (PCP-TeCP-TriCP polychlorophenols) 9(IS - 17011,Table - 1(xi) (Phthalates (each individual phthalate)) Phtha 9(IS - 17011,Table - 1(xii) (Nickel, on skin contact)

IS 5557 : Part 1 (2024)

All Rubber Gum Boots and Ankle Boots Part 1 Safety and Protective

25000 View breakup
-

Clause No.	Exclusion	Remark
Cl-5(Design)	-	-
6(Sizes and Fittines)	-	-
7(Consturction)	-	-
8.1(Lining Material)	-	-
8.2, Table-1 (i)(Width, mm, Min)	-	-
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	-
8.4(Use of Rubber material)	-	-
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	-
8.5(Upper material)	-	-
8.5.1(Tensile Strength of upper)	-	-
8.5.2(Thickness)	-	-
8.5.3(Flexing Resistance)	-	-
8.5.4(Abrasion Resistance)	-	-
8.6.1(Thickness of Outsole)	-	-
8.6.2(Tear Strength)	-	-
8.6.5(Inter layer Bond Strength of outsole)	-	-
8.6.3(Abrasion Resistance of Outsole)	-	-
Cl-8.7(Insocks material)	-	-
8.7.1(Thickness of Insocks)	-	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	-
Cl-8.8.1(Outsole/Heel)	-	-
Cl-8.9(Leak Proof Test)	-	-
8.10(Height of Upper)	-	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	-
Cl-8.12(Upper Outsole Bond Strength)	-	-
Cl-8.13(Internal Length of Toe Cap)	-	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	-
8.16(Banned Chemicals)	-	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	-
8.17(Steel Floor with Glycerine)	-	-
8.18(Corrosion Resistant Test for Toe Caps)	-	-
9.1(Penetration Resistance)	-	-
9.2(Antistatic Footwear)	-	-
9.3(Flame Resistance Property)	-	-
9.4(Electrical Resistance)	-	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	-
9.6(Resistance to Fuel Oil)	-	-
11.2(Marking)	-	-
8.6.4(Flexing Resistance)	-	-
Cl-5(Design)	-	-
6(Sizes and Fittines)	-	-
7(Consturction)	-	-
8.1(Lining Material)	-	-
8.2, Table-1 (i)(Width, mm, Min)	-	-
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	-
8.4(Use of Rubber material)	-	-
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	-
8.5(Upper material)	-	-
8.5.1(Tensile Strength of upper)	-	-
8.5.2(Thickness)	-	-
8.5.3(Flexing Resistance)	-	-
8.5.4(Abrasion Resistance)	-	-
8.6.1(Thickness of Outsole)	-	-
8.6.2(Tear Strength)	-	-
8.6.5(Inter layer Bond Strength of outsole)	-	-
8.6.3(Abrasion Resistance of Outsole)	-	-
Cl-8.7(Insocks material)	-	-
8.7.1(Thickness of Insocks)	-	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	-
Cl-8.8.1(Outsole/Heel)	-	-
Cl-8.9(Leak Proof Test)	-	-
8.10(Height of Upper)	-	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	-
Cl-8.12(Upper Outsole Bond Strength)	-	-
Cl-8.13(Internal Length of Toe Cap)	-	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	-
8.16(Banned Chemicals)	-	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	-
8.17(Steel Floor with Glycerine)	-	-
8.18(Corrosion Resistant Test for Toe Caps)	-	-
9.1(Penetration Resistance)	-	-
9.2(Antistatic Footwear)	-	-
9.3(Flame Resistance Property)	-	-
9.4(Electrical Resistance)	-	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	-
9.6(Resistance to Fuel Oil)	-	-
11.2(Marking)	-	-
8.6.4(Flexing Resistance)	-	-

26 Oct, 2025

-
Included w.e.f.18.08.2025

IS 15298 : Part 2 (2024)

Personal Protective Equipment Part 2 Safety Footwear (ISO 20345 : 2021, MOD) (Third Revision)

39999.99 View breakup
-

Clause No.	Exclusion	Remark
Cl 5.2(Design)	-	-
Cl 5.2.2, Table 4(" Height of upper ")	-	-
Cl 5.2.3(Heel area)	-	-
Cl 5.3.1.1(Construction of whole footwear)	-	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	-
Cl 5.3.2.1(Toe protection - general)	-	-
Cl 5.3.2.2(Internal length)	-	-
Cl 5.3.2.3(Width of toecap flange)	-	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	-
Cl 5.3.2.6(Impact resistance)	-	-
Cl 5.3.2.7(Compression resistance)	-	-
Cl 5.3.3(Leak proofness)	-	-
Cl 5.3.4("Specific ergonomic features ")	-	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	-
Cl 5.3.7(Seam strength)	-	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	-
Cl 5.3.8(Lead Content ( National Annex A))	-	-
Cl 5.4.2(Thickness)	-	-
Cl 5.4.3(Tear strength)	-	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-
Cl 5.4.5(Flexing resistance)	-	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	-
Cl 5.4.7(Resistance to hydrolysis)	-	-
Cl 5.5.2(Lining- Tear strength)	-	-
Cl 5.5.3(Lining- Abrasion resistance)	-	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	-
Cl 5.7.2(Water permeability of insock)	-	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	-
Cl 5.8.2.2(Cleated area)	-	-
Cl 5.8.2.3(Cleat height)	-	-
Cl 5.8.3(Outsole- Tear strength)	-	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	-
Cl 5.8.5(Outsole-Flexing resistance)	-	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	-
Cl 5.8.7(Interlayer bond strength)	-	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	-
Cl 6.2.4(Energy absorption of seat region)	-	-
Cl 6.2.5(Water resistance)	-	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	-
Cl 6.2.7(Ankle protection)	-	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	-
Cl 6.2.8.3(Resistance to cutting)	-	-
Cl 6.2.9(Scuff cap)	-	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	-
Cl 6.3(Upper — Water penetration and absorption)	-	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	-
Cl 7, Table 20("Marking ")	-	-
Cl 6.4.3.2(Design of Ladder grip)	-	-
Cl 5.2(Design)	-	-
Cl 5.2.2, Table 4(" Height of upper ")	-	-
Cl 5.2.3(Heel area)	-	-
Cl 5.3.1.1(Construction of whole footwear)	-	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	-
Cl 5.3.2.1(Toe protection - general)	-	-
Cl 5.3.2.2(Internal length)	-	-
Cl 5.3.2.3(Width of toecap flange)	-	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	-
Cl 5.3.2.6(Impact resistance)	-	-
Cl 5.3.2.7(Compression resistance)	-	-
Cl 5.3.3(Leak proofness)	-	-
Cl 5.3.4("Specific ergonomic features ")	-	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	-
Cl 5.3.7(Seam strength)	-	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	-
Cl 5.3.8(Lead Content ( National Annex A))	-	-
Cl 5.4.2(Thickness)	-	-
Cl 5.4.3(Tear strength)	-	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-
Cl 5.4.5(Flexing resistance)	-	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	-
Cl 5.4.7(Resistance to hydrolysis)	-	-
Cl 5.5.2(Lining- Tear strength)	-	-
Cl 5.5.3(Lining- Abrasion resistance)	-	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	-
Cl 5.7.2(Water permeability of insock)	-	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	-
Cl 5.8.2.2(Cleated area)	-	-
Cl 5.8.2.3(Cleat height)	-	-
Cl 5.8.3(Outsole- Tear strength)	-	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	-
Cl 5.8.5(Outsole-Flexing resistance)	-	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	-
Cl 5.8.7(Interlayer bond strength)	-	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	-
Cl 6.2.4(Energy absorption of seat region)	-	-
Cl 6.2.5(Water resistance)	-	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	-
Cl 6.2.7(Ankle protection)	-	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	-
Cl 6.2.8.3(Resistance to cutting)	-	-
Cl 6.2.9(Scuff cap)	-	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	-
Cl 6.3(Upper — Water penetration and absorption)	-	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	-
Cl 7, Table 20("Marking ")	-	-
Cl 6.4.3.2(Design of Ladder grip)	-	-

26 Oct, 2025

-
Included w.e.f.18.08.2025 Exclusion excluding Innocuousness test as per Cl 5.3.6

IS 14490 (2024)

Plain Copier Paper â Specification (Second Revision)

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(plain copier paper)	-	500	-
5.1.2(k,)	-	500	-
5.2(0)	-	500	-
5.3(Grammage (Substance))	-	1000	-
5.4(Thickness)	-	500	-
5.5(Size)	-	1000	-
5.7(Conditioning)	-	1000	-
5.8(Additional Requirements for Eco-Mark)	-	1000	-
5.6, Table 1, i(ISO brightness, percent, Min)	-	1000	-
5.6, Table 1, ii(Opacity, percent, Min)	-	1000	-
5.6, Table 1, iii(One minute cobb test, both sides, g/m2 , Max)	-	1000	-
5.6, Table 1, iv(Surface strength, Dennison (Wax Pick))	-	1000	-
5.6, Table 1, v(Smoothness for both sides (Bendsten), ml/min, Max)	-	1000	-
5.6, Table 1, vi(Ash content (at 900 °C), percent by mass, Max)	-	1000	-
5.6, Table 1, vii(Taber stiffness, Min:)	-	1000	-
5.6, Table 1, viii(Tear Index, mN.m2 /g, Min:)	-	1000	-
5.6, Table 1, ix(Tensile index, N.m/g, Min:)	-	1000	-
6(PACKING AND MARKING)	-	1000	-
5.1.1(plain copier paper)	-	0	-
5.1.2(k,)	-	0	-
5.2(0)	-	0	-
5.3(Grammage (Substance))	-	0	-
5.4(Thickness)	-	0	-
5.5(Size)	-	0	-
5.7(Conditioning)	-	0	-
5.8(Additional Requirements for Eco-Mark)	-	0	-
5.6, Table 1, i(ISO brightness, percent, Min)	-	0	-
5.6, Table 1, ii(Opacity, percent, Min)	-	0	-
5.6, Table 1, iii(One minute cobb test, both sides, g/m2 , Max)	-	0	-
5.6, Table 1, iv(Surface strength, Dennison (Wax Pick))	-	0	-
5.6, Table 1, v(Smoothness for both sides (Bendsten), ml/min, Max)	-	0	-
5.6, Table 1, vi(Ash content (at 900 °C), percent by mass, Max)	-	0	-
5.6, Table 1, vii(Taber stiffness, Min:)	-	0	-
5.6, Table 1, viii(Tear Index, mN.m2 /g, Min:)	-	0	-
5.6, Table 1, ix(Tensile index, N.m/g, Min:)	-	0	-
6(PACKING AND MARKING)	-	0	-
5.1.1(plain copier paper)	-	0	-
5.1.2(k,)	-	0	-
5.2(0)	-	0	-
5.3(Grammage (Substance))	-	0.01	-
5.4(Thickness)	-	0	-
5.5(Size)	-	0	-
5.7(Conditioning)	-	0	-
5.8(Additional Requirements for Eco-Mark)	-	0	-
5.6, Table 1, i(ISO brightness, percent, Min)	-	0	-
5.6, Table 1, ii(Opacity, percent, Min)	-	0	-
5.6, Table 1, iii(One minute cobb test, both sides, g/m2 , Max)	-	0	-
5.6, Table 1, iv(Surface strength, Dennison (Wax Pick))	-	0.01	-
5.6, Table 1, v(Smoothness for both sides (Bendsten), ml/min, Max)	-	0	-
5.6, Table 1, vi(Ash content (at 900 °C), percent by mass, Max)	-	0	-
5.6, Table 1, vii(Taber stiffness, Min:)	-	0	-
5.6, Table 1, viii(Tear Index, mN.m2 /g, Min:)	-	0	-
5.6, Table 1, ix(Tensile index, N.m/g, Min:)	-	0	-
6(PACKING AND MARKING)	-	0	-
5.1.1(plain copier paper)	-	0	-
5.1.2(k,)	-	0	-
5.2(0)	-	0	-
5.3(Grammage (Substance))	-	0	-
5.4(Thickness)	-	0	-
5.5(Size)	-	0	-
5.7(Conditioning)	-	0	-
5.8(Additional Requirements for Eco-Mark)	-	0	-
5.6, Table 1, i(ISO brightness, percent, Min)	-	0	-
5.6, Table 1, ii(Opacity, percent, Min)	-	0	-
5.6, Table 1, iii(One minute cobb test, both sides, g/m2 , Max)	-	0	-
5.6, Table 1, iv(Surface strength, Dennison (Wax Pick))	-	0	-
5.6, Table 1, v(Smoothness for both sides (Bendsten), ml/min, Max)	-	0	-
5.6, Table 1, vi(Ash content (at 900 °C), percent by mass, Max)	-	0	-
5.6, Table 1, vii(Taber stiffness, Min:)	-	0	-
5.6, Table 1, viii(Tear Index, mN.m2 /g, Min:)	-	0	-
5.6, Table 1, ix(Tensile index, N.m/g, Min:)	-	0	-
6(PACKING AND MARKING)	-	0	-

26 Oct, 2025

-
Included w.e.f.28.05.2025

IS 14490 (2018)

Plain copier paper - Specification (First Revision)

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	1000	-
5.1(General)	-	1000	-
5.2(Moisture (IS 1060 (Part 5/Sec 2)).)	-	1000	-
5.3(Grammage IS 1060 (Part 5/Sec 5) & IS 1060 (Part 4/Sec 1))	-	1000	-
5.3(Grammage IS 1060 (Part 5/Sec 5) & IS 1060 (Part 4/Sec 1))	-	1000	-
5.3(Grammage IS 1060 (Part 5/Sec 5) & IS 1060 (Part 4/Sec 1))	-	1000	-
5.4(Thickness IS 1060 (Part 5/Sec 3).)	-	1000	-
5.5 Table 1 i(ISO brightness IS/ISO 2470 (Part 1))	-	2000	-
5.5 Table 1 ii(Opacity IS/ISO 2471)	-	2000	-
5.5 Table 1 iii(One minute cobb test, both sides IS 1060 (Part 5/Sec 4))	-	2000	-
5.5 Table 1 iv(Surface strength, Dennison (Wax Pick) 8 of IS 1060 (Part 3))	-	2000	-
5.5 Table 1 v(Smoothness for both sides (Bendsten) 3 of IS 9894)	-	2000	-
5.5 Table 1 vi(Ash content (at 900°C) 11 of IS 1060 (Part 1))	-	2000	-
5.5 Table 1 vii a(Taber stiffness, Machine direction (MD) Appendix D of IS 4658)	-	1000	-
5.5 Table 1 vii b(Taber stiffness, Cross direction (CD) Appendix D of IS 4658)	-	1000	-
5.5 Table 1 viii a(Tear index Machine direction (MD) IS 1060 (Part 6/Sec 1))	-	1000	-
5.5 Table 1 viii a(Tear index Cross direction (CD) IS 1060 (Part 6/Sec 1))	-	1000	-
5.5 Table 1 ix a(Tensile index, Machine direction (MD) IS 1060 (Part 5/Sec 6))	-	1000	-
5.5 Table 1 ix b(Tensile index,Cross direction (CD) IS 1060 (Part 5/Sec 6))	-	1000	-
5.1(General)	-	1000	-
5.1(General)	-	1000	-
5.2(Moisture (IS 1060 (Part 5/Sec 2)).)	-	1000	-
5.3(Grammage IS 1060 (Part 5/Sec 5) & IS 1060 (Part 4/Sec 1))	-	1000	-
5.3(Grammage IS 1060 (Part 5/Sec 5) & IS 1060 (Part 4/Sec 1))	-	1000	-
5.3(Grammage IS 1060 (Part 5/Sec 5) & IS 1060 (Part 4/Sec 1))	-	1000	-
5.4(Thickness IS 1060 (Part 5/Sec 3).)	-	1000	-
5.5 Table 1 i(ISO brightness IS/ISO 2470 (Part 1))	-	2000	-
5.5 Table 1 ii(Opacity IS/ISO 2471)	-	2000	-
5.5 Table 1 iii(One minute cobb test, both sides IS 1060 (Part 5/Sec 4))	-	2000	-
5.5 Table 1 iv(Surface strength, Dennison (Wax Pick) 8 of IS 1060 (Part 3))	-	2000	-
5.5 Table 1 v(Smoothness for both sides (Bendsten) 3 of IS 9894)	-	2000	-
5.5 Table 1 vi(Ash content (at 900°C) 11 of IS 1060 (Part 1))	-	2000	-
5.5 Table 1 vii a(Taber stiffness, Machine direction (MD) Appendix D of IS 4658)	-	1000	-
5.5 Table 1 vii b(Taber stiffness, Cross direction (CD) Appendix D of IS 4658)	-	1000	-
5.5 Table 1 viii a(Tear index Machine direction (MD) IS 1060 (Part 6/Sec 1))	-	1000	-
5.5 Table 1 viii a(Tear index Cross direction (CD) IS 1060 (Part 6/Sec 1))	-	1000	-
5.5 Table 1 ix a(Tensile index, Machine direction (MD) IS 1060 (Part 5/Sec 6))	-	1000	-
5.5 Table 1 ix b(Tensile index,Cross direction (CD) IS 1060 (Part 5/Sec 6))	-	1000	-
Cl.5.1(Description)	-	1000	-
Cl.5.2(Moisture)	-	1000	-
Cl.5.2(Moisture)	-	1000	-
Cl.5.3(Grammage (Substance))	-	1000	-
Cl.5.4(Thickness)	-	1000	-
Cl.5.6(Size)	-	1000	-
Cl.5.5, Table-1(i)(ISO Brightness)	-	2000	-
Cl.5.5, Table-1(ii)(Opacity)	-	2000	-
Cl.5.5, Table-1(iii)(One minute cobb test, Both sides)	-	2000	-
Cl.5.5, Table-1(iv)(Surface strength, Dennison)	-	2000	-
Cl.5.5, Table-1(v)(Smoothness for both sides (Bendtsen))	-	2000	-
Cl.5.5, Table-1(vi)(Ash content)	-	2000	-
Cl.5.5, Table-1(vii)(Taber stiffness (MD))	-	1000	-
Cl.5.5, Table-1(viii)(Taber stiffness (CD))	-	1000	-
Cl.5.5, Table-1(ix)(Tear Index (MD))	-	1000	-
Cl.5.5, Table-1(x)(Tear Index (CD))	-	1000	-
Cl.5.5, Table-1(xi)(Tensile index (MD))	-	1000	-
Cl.5.5, Table-1(xii)(Tensile index (CD))	-	1000	-
Cl.5.1(Moisture)	-	1000	-
Cl.5.2(Crude Protein (Nx6.25))	-	0	-
Cl.5.3(Ether extract)	-	0	-
Cl.5.4(Crude fibre)	-	0	-
Cl.5.6(Acid insoluble Ash)	-	0	-
Cl.5.5, Table-1(i)(Salt (as NaCl))	-	0	-
Cl.5.5, Table-1(i)(Salt (as NaCl))	-	0	-
Cl.5.5, Table-1(i)(Calcium (as Ca))	-	0	-
Cl.5.5, Table-1(i)(Total phosphorous)	-	0	-
Cl.5.5, Table-1(i)(Available Phosphorous)	-	0	-
Cl.5.5, Table-1(i)(Lysine)	-	0	-
Cl.5.5, Table-1(i)(Methionine)	-	0	-
Cl.5.5, Table-1(i)(Methionine + Cysteine)	-	0	-
Cl.5.5, Table-1(i)(Metabolizable energy)	-	0	-
Cl.5.5, Table-1(i)(Aflatoxin B1)	-	0	-
Cl.5.1(Description)	-	1000	-
Cl.5.2(Moisture)	-	1000	-
Cl.5.3(Grammage (Substance))	-	1000	-
Cl.5.4(Thickness)	-	1000	-
Cl.5.6(Size)	-	1000	-
Cl.5.5, Table-1(i)(ISO Brightness)	-	2000	-
Cl.5.5, Table-1(ii)(Opacity)	-	2000	-
Cl.5.5, Table-1(iii)(One minute cobb test, Both sides)	-	2000	-
Cl.5.5, Table-1(iv)(Surface strength, Dennison)	-	2000	-
Cl.5.5, Table-1(v)(Smoothness for both sides (Bendtsen))	-	2000	-
Cl.5.5, Table-1(vi)(Ash content)	-	2000	-
Cl.5.5, Table-1(vii)(Taber stiffness (MD))	-	1000	-
Cl.5.5, Table-1(viii)(Taber stiffness (CD))	-	1000	-
Cl.5.5, Table-1(ix)(Tear Index (MD))	-	1000	-
Cl.5.5, Table-1(x)(Tear Index (CD))	-	1000	-
Cl.5.5, Table-1(xi)(Tensile index (MD))	-	1000	-
Cl.5.5, Table-1(xii)(Tensile index (CD))	-	1000	-
General(General)	-	1000	-
Cl. 5.2(Moisture)	-	1000	-
Cl. 5.3(Grammage (Substance))	-	1000	-
Cl. 5.4(Thickness)	-	1000	-
Cl. 5.6(Size)	-	1000	-
Cl. 5.5, Table 1, Sl. No. (i)(ISO brightness)	-	2000	-
Cl. 5.5, Table 1, Sl. No. (ii)(Opacity)	-	2000	-
Cl. 5.5, Table 1, Sl. No. (iii)(One minute cobb test, both sides)	-	2000	-
Cl. 5.5, Table 1, Sl. No. (iv)(Surface strength, Dennison (Wax Pick))	-	2000	-
Cl. 5.5, Table 1, Sl. No. (v)(Smoothness for both sides (Bendsten))	-	2000	-
Cl. 5.5, Table 1, Sl. No. (vi)(Ash content (at 900°C))	-	2000	-
Cl. 5.5, Table 1, Sl. No. (vii), (a)(Taber stiffness (MD))	-	1000	-
Cl. 5.5, Table 1, Sl. No. (vii), (a)(Taber stiffness (CD))	-	1000	-
Cl. 5.5, Table 1, Sl. No. (viii), (a)(Tear Index (MD))	-	1000	-
Cl. 5.5, Table 1, Sl. No. (vii), (a)(Tear Index (CD))	-	1000	-
Cl. 5.5, Table 1, Sl. No. (vii), (a)(Tensile Index (MD))	-	1000	-
Cl. 5.5, Table 1, Sl. No. (vii), (a)(Tensile Index (CD))	-	1000	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 1848 : Part 1 (2018)

Writing and printing papers - Specification: Part 1 account book, azure lead, bond, cream laid and cream wove/printing white/printing coloured/printing offset, printing maplitho, printing white super calendered and typewriting types (Fifth Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.2(Substance)	-	1000	-
Cl. 4.4(Size and tolerance on size)	-	1000	-
Cl.4.5(pH)	-	1000	-
Table-1(i)(Tensile index, CD)	-	1000	-
Table-1(i)(Tensile index, MD)	-	1000	-
Table-1(ii)(Brightness, ISO)	-	1000	-
Table-1(iii)(Opacity)	-	2000	-
Table-1(iv)(One minute cobb test)	-	2000	-
Table-1(v)(No of double fold, CD)	-	750	-
Table-1(v)(No of double fold, MD)	-	750	-
Table-1(vi)(Gloss)	-	1500	-
Table-1(vii)(Wax pick)	-	2000	-
Table-1(viii)(Smoothness (Bendtsen))	-	2000	-
Table-1(ix)(Tear index, CD)	-	1000	-
Table-1(ix)(Tear index, MD)	-	1000	-
Cl.4.2(Substance, Ref IS 1763)	-	1000	-
Cl. 4.4(Size and tolerance on size)	-	1000	-
Cl. 4.5(pH)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Tensile index, Account book-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Tensile index, Account book-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Brightness ISO, Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Opacity, Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(One minute cobb test, Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Double fold, Account book-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Double fold, Account book-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Gloss, Account book)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Wax pick, Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Smoothness(Bendtsen),Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Tear index, Account book-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Tear index, Account book-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Tensile index, Azure laid-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Tensile index, Azure laid-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Brightness ISO, Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Opacity,Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(One minute cobb test, Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Double fold, Azure laid-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Double fold, Azure laid-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Gloss, Azure laid)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Wax pick, Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Smoothness(Bendtsen),Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Tear index, Azure laid-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Tear index, Azure laid-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Tensile index, Bond-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Tensile index, Bond-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Brightness ISO, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Opacity, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(One minute cobb test, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Double fold, Bond-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Double fold, Bond-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Gloss, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Wax pick, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Smoothness(Bendtsen),Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Tear index, Bond-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Tear index, Bond-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Tensile index, Cream laid and cream wove/printing white/printing coloured/printing offset-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Tensile index, Cream laid and cream wove/printing white/printing coloured/printing offset-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Brightness ISO, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Opacity, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(One minute cobb test, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Double fold, Cream laid and cream wove/printing white/printing coloured/printing offset-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Double fold, Cream laid and cream wove/printing white/printing coloured/printing offset-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Gloss, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Wax pick, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Smoothness bendtsen, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Tear index, Cream laid and cream wove/printing white/printing coloured/printing offset-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Tear index, Cream laid and cream wove/printing white/printing coloured/printing offset-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Tensile index, Printing Maplitho-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Tensile index, Printing Maplitho-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Brightness ISO, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Opacity, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(One minute cobb test, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Double fold, Printing Maplitho-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Double fold, Printing Maplitho-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Gloss, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Wax pick, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Smoothness bendtsen, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Tear index, Printing Maplitho-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Tear index, Printing Maplitho-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tensile index, Printing White Super Calendered-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tensile index, Printing White Super Calendered-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Brightness ISO, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Opacity, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(One minute cobb test, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Double fold, Printing White Super Calendered-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Double fold, Printing White Super Calendered-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Gloss, Printing White Super Calendered)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Wax pick, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Smoothness bendtsen, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tear index, Printing White Super Calendered-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tear index, Printing White Super Calendered-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tensile index, Typewriting-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Tensile index, Typewriting-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Brightness ISO, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Opacity, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(One minute cobb test, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Double fold, Typewriting-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Double fold, Typewriting-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Gloss, Typewriting)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Wax pick, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Smoothness bendtsen, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Tear index, Typewriting-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Tear index, Typewriting-MD)	-	1000	-
Cl.4.2(Substance, Ref IS 1763)	-	1000	-
Cl. 4.5(pH)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Tensile index, Account book-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Tensile index, Account book-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Brightness ISO, Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Opacity, Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(One minute cobb test, Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Double fold, Account book-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Double fold, Account book-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Gloss, Account book)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Wax pick, Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Smoothness(Bendtsen),Account book)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Tear index, Account book-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. i(Tear index, Account book-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Tensile index, Azure laid-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Tensile index, Azure laid-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Brightness ISO, Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Opacity,Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(One minute cobb test, Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Double fold, Azure laid-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Double fold, Azure laid-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Gloss, Azure laid)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Wax pick, Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Smoothness(Bendtsen),Azure laid)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Tear index, Azure laid-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. ii(Tear index, Azure laid-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Tensile index, Bond-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Tensile index, Bond-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Brightness ISO, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Opacity, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(One minute cobb test, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Double fold, Bond-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Double fold, Bond-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Gloss, Bond)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Wax pick, Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Smoothness(Bendtsen),Bond)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Tear index, Bond-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iii(Tear index, Bond-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Tensile index, Cream laid and cream wove/printing white/printing coloured/printing offset-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Tensile index, Cream laid and cream wove/printing white/printing coloured/printing offset-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Brightness ISO, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Opacity, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(One minute cobb test, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Double fold, Cream laid and cream wove/printing white/printing coloured/printing offset-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Double fold, Cream laid and cream wove/printing white/printing coloured/printing offset-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Gloss, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Wax pick, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Smoothness bendtsen, Cream laid and cream wove/printing white/printing coloured/printing offset)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Tear index, Cream laid and cream wove/printing white/printing coloured/printing offset-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. iv(Tear index, Cream laid and cream wove/printing white/printing coloured/printing offset-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Tensile index, Printing Maplitho-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Tensile index, Printing Maplitho-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Brightness ISO, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Opacity, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(One minute cobb test, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Double fold, Printing Maplitho-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Double fold, Printing Maplitho-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Gloss, Printing Maplitho)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Wax pick, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Smoothness bendtsen, Printing Maplitho)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Tear index, Printing Maplitho-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. v(Tear index, Printing Maplitho-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tensile index, Printing White Super Calendered-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tensile index, Printing White Super Calendered-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Brightness ISO, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Opacity, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(One minute cobb test, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Double fold, Printing White Super Calendered-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Double fold, Printing White Super Calendered-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Gloss, Printing White Super Calendered)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Wax pick, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Smoothness bendtsen, Printing White Super Calendered)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tear index, Printing White Super Calendered-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tear index, Printing White Super Calendered-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vi(Tensile index, Typewriting-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Tensile index, Typewriting-MD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Brightness ISO, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Opacity, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(One minute cobb test, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Double fold, Typewriting-CD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Double fold, Typewriting-MD)	-	750	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Gloss, Typewriting)	-	1500	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Wax pick, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Smoothness bendtsen, Typewriting)	-	2000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Tear index, Typewriting-CD)	-	1000	-
Cl. 4.6,4.7,6.2, Table No. 1, Sl no. vii(Tear index, Typewriting-MD)	-	1000	-
Cl.4.1(Description)	-	1000	-
Cl.4.2.1(Tolerances on nominal substance)	-	1000	-
Cl.4.3(Thickness)	-	1000	-
Cl.4.4(Sizes and tolerances on sizes)	-	1000	-
Cl.4.1(Mechanical pulp)	-	1000	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 3039 (1988)

Specification for structural steel for construction of hulls of ships (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1 & Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1 & Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1 & Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1 & Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1 & Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1 & Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
5(Freedom from defects)	-	1000	-
10.2(Tensile Test-1608:Part 1)	-	3000	-
10.2(Yield Stress, Mpa)	-	3000	-
10.2(Tensile Strength, Mpa)	-	3000	-
10.2(Elongation, %)	-	3000	-
11(Impact Test-1757)	-	5000	-
12 and 13(Dimensions and Tolerances)	-	1000	-
Cl. 6.1, Table no 1(Carbon +( Manganese / 6))	-	500	-
Cl. 6.1, Table no 1(aluminium)	-	500	-
Cl. 6.1, Table no 1(Phosphorous)	-	500	-
Cl. 6.1, Table no 1(Sulphur)	-	500	-
Cl. 6.1, Table no 1(Silicon)	-	500	-
Cl. 6.1, Table no 1(Manganese)	-	500	-
Cl. 6.1, Table no 1(carbon)	-	500	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 2385 (1977)

Specification for hot - Rolled mild steel sheet and strip in coil form for cold - Reduced tinplate and cold - Reduced blackplate (First Revision)

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.1, 5.2 & Table1(Carbon- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Manganese- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Sulphur- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Phosphorus- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Nitrogen- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Aluminium- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
6(Freedom from defects)	-	1000	-
8(Dimensions and Tolerances)	-	1000	-
Cl. 5.1, 5.2(chromium)	-	500	-
Cl. 5.1, 5.2(silicon)	-	500	-
Cl. 5.1, 5.2(copper)	-	500	-
Cl. 5.1, 5.2(aluminium)	-	500	-
Cl. 5.1, 5.2(Nitrogen )	-	500	-
Cl. 5.1, 5.2(Phosphorus)	-	500	-
Cl. 5.1, 5.2(Sulphur)	-	500	-
Cl. 5.1, 5.2(Manganese)	-	500	-
Cl. 5.1, 5.2(carbon)	-	500	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Sulphur -IS 228 or method specified in relevant ISO standard)	-	500	-
Cl.4(Phosphorus -IS 228 or method specified in relevant ISO standard)	-	500	-
5.2(Tensile Test-1608:Part 1)	-	3000	-
5.2(Tensile Strength, Mpa)	-	3000	-
5.2(Elongation, %)	-	3000	-
5.3(Bend Test-1599)	-	1500	-
7.1(Freedom from defects)	-	1000	-
8.2(Width)	-	1000	-
8.2(Thickness)	-	1000	-
9.1(Finishing & Packing)	-	1000	-
10(Marking)	-	1000	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
8.2, Table 3(Tensile Test-1608:Part 1)	-	3000	-
8.2, Table 3(Proof Stress, N/mm2)	-	3000	-
8.2, Table 3(Tensile Strength, N/mm2)	-	3000	-
8.2, Table 3(Elongation, %)	-	1000	-
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	2000	-
8.4(Bend Test)	-	1500	-
8.5(Erichsen Cupping Test)	-	1000	-
10.1(Thickness, mm)	-	1000	-
10.2(width, mm)	-	1000	-
10.3(Length, mm)	-	1000	-
10.4(Flatness,mm)	-	1000	-
10.5(Camber, mm)	-	1000	-
11(Surface Finish)	-	500	-
Cl . 6 .0(Freedom from defect)	-	500	-
13(Marking)	-	500	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8 & Table 3(UTM)	-	3000	-
Cl 9(Press)	-	1500	-
Cl 11(Workmanship)	-	1000	-
Cl 12 & 13(Length, Width & Thickness)	-	1000	-
Cl 8 & Table 3(UTM)	-	3000	-
Cl 9(Press)	-	1500	-
Cl 11(Workmanship)	-	1000	-
Cl 12 & 13(Length, Width & Thickness)	-	1000	-
Cl 8 & Table 3(UTM)	-	3000	-
Cl 9(Press)	-	1500	-
Cl 11(Workmanship)	-	1000	-
Cl 12 & 13(Length, Width & Thickness)	-	1000	-
7.1(Carbon %)	-	500	-
7.1(Manganese %)	-	500	-
7.1(Phosphorus %)	-	500	-
7.1(Sulphur %)	-	500	-
7.1(Silicon %)	-	500	-
7.1( Copper %)	-	500	-
7.1( Aluminium %)	-	500	-
7.1( Nb)	-	500	-
7.1(V)	-	500	-
7.1( Ti)	-	500	-
7.1(Cr)	-	500	-
7.1(Mo)	-	500	-
7.1(Ni)	-	500	-
7.1( Nitrogen%)	-	500	-
7.1(CE)	-	500	-
7.1(Carbon %)	-	500	-
7.1(Manganese %)	-	500	-
7.1(Phosphorus %)	-	500	-
7.1(Sulphur %)	-	500	-
7.1(Silicon %)	-	500	-
7.1( Copper %)	-	500	-
7.1( Aluminium %)	-	500	-
7.1( Nb)	-	500	-
7.1(V)	-	500	-
7.1( Ti)	-	500	-
7.1(Cr)	-	500	-
7.1(Mo)	-	500	-
7.1(Ni)	-	500	-
7.1( Nitrogen%)	-	500	-
7.1(CE)	-	500	-
7.1(Carbon %)	-	500	-
7.1(Manganese %)	-	500	-
7.1(Phosphorus %)	-	500	-
7.1(Sulphur %)	-	500	-
7.1(Silicon %)	-	500	-
7.1( Copper %)	-	500	-
7.1( Aluminium %)	-	500	-
7.1( Nb)	-	500	-
7.1(V)	-	500	-
7.1( Ti)	-	500	-
7.1(Cr)	-	500	-
7.1(Mo)	-	500	-
7.1(Ni)	-	500	-
7.1( Nitrogen%)	-	500	-
7.1(CE)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(TITANIUM)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(VANADIUM)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(NIOBIUM)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(CARBON EQUIVELENT )	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(Molybdenum)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(Chromium)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(Nickel)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(SILICON)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(NITROGEN)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(MANGANESE)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(PHOSPHURS)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(SULPHUR)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )( CARBON)	-	500	-
Cl. 14(Weight)	-	1000	-
Cl. 12, 13(Camber)	-	500	-
Cl. 12, 13(Thickness)	-	1000	-
Cl. 8, Table 3(Elongation)	-	1000	-
Cl. 8, Table 3(Yield Stress)	-	3000	-
Cl 12 & 13(Length, Width & Thickness)	-	1000	-
Cl 11(Workmanship)	-	1000	-
Cl 9(Press)	-	1500	-
Cl 8 & Table 3(UTM)	-	3000	-
Cl 8 & Table 3(UTM)	-	3000	-
Cl 9(Press)	-	1500	-
Cl 11(Workmanship)	-	1000	-
Cl 12 & 13(Length, Width & Thickness)	-	1000	-
7.0 (7)(Micro Alloying elements - IS:8811)	-	500	-
8.0 (1)(Tensile Strength-IS:1608(P1))	-	3000	-
8.0 (2)(Yield Strength-IS:1608(P1))	-	3000	-
8.0 (3)(Elongation on 5.65 SoA GL-IS:1608(P1))	-	1000	-
12 (1)(Width - SOP MT-23)	-	1000	-
12 (2)(Thickness- SOP MT-23)	-	1000	-
12 (3)(Mass of Strip- SOP MT-23)	-	1000	-
15.0 & 15.1(Coil edges - IS:10748)	-	1000	-
15.0 & 15.2(Surface finish - IS:10748)	-	1000	-
15.0 & 15.5(Telescopicity - IS:10748)	-	1000	-
15(Condition of Coil)	-	500	-
16(Marking)	-	500	-
3.4(Vehicle Fuel System)	-	500	-
9(Protective Treatment)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(Tungsten (W))	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(Boron (B))	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )( ALUMINIUM)	-	500	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	1000	-
Cl 9(Nominal Diameter & Out Of Shape)	-	1000	-
Cl 8(Workmanship)	-	1000	-
Cl 9(Nominal Diameter & Out Of Shape)	-	1000	-
Cl 8(Freedom from defects)	-	1000	-
Cl 9(Nominal Diameter & Out Of Shape)	-	1000	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
Cl. 9(Out of Shape)	-	1000	-
Cl 9(Nominal Diameter & Out Of Shape)	-	1000	-
Cl 8(Workmanship)	-	1000	-
Cl 8(Workmanship)	-	1000	-
Cl 9(Nominal Diameter & Out Of Shape)	-	1000	-
Table 1 Note 3(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(By Calculation)	-	500	-
Table 1 Note 3(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(Any Instrumental Method/Chemical Method)	-	500	-
Amendment 1(By Calculation)	-	500	-
Table 1 Note 3(Copper)	-	500	-
Amendment 1(Niobium)	-	500	-
Amendment 1(Vanadium)	-	500	-
Amendment 1(Titanium)	-	500	-
Amendment 1(Micro Alloying Element (Nb+V+Ti))	-	1000	-
9.1(Diameter - SOP-MT-23)	-	1000	-
9.3(Out of Shape - SOP-MT-23)	-	1000	-
11(Marking)	-	1000	-
Table 1 Note 3(Copper)	-	500	-
Amendment 1(Niobium)	-	500	-
Amendment 1(Vanadium)	-	500	-
Amendment 1(Titanium)	-	500	-
Amendment 1(Micro Alloying Element (Nb+V+Ti))	-	1000	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 13(Length, Width & Thickness)	-	1000	-
Cl 7(UTM)	-	3000	-
Cl 7(UTM)	-	3000	-
7(Elongation -IS:1608(P1))	-	3000	-
Cl 8(Press)	-	1500	-
Cl 9(Strainage Embrittlement)	-	1500	-
Cl 10(Erichsen Cupping)	-	3000	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
Cl 7(UTM)	-	3000	-
Cl 8(Press)	-	1500	-
Cl 7(UTM)	-	3000	-
Cl 8(Press)	-	1500	-
Cl 9(Strainage Embrittlement)	-	1500	-
Cl 10(Erichsen Cupping)	-	3000	-
Cl 13(Length, Width & Thickness)	-	1000	-
Cl 7(UTM)	-	3000	-
Cl 9(Strainage Embrittlement)	-	1500	-
Cl 10(Erichsen Cupping)	-	1500	-
Cl 13(Length, Width & Thickness)	-	1000	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1(Nitrogen%)	-	500	-
6.1( Aluminium %)	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
Cl. 13(Out of square)	-	500	-
Cl. 13(Flatness)	-	1000	-
Cl. 13(Camber)	-	1000	-
Cl. 13(Width)	-	1000	-
Cl. 13(Thickness)	-	1000	-
Cl. 12(Freedom from defects)	-	1000	-
Cl. 7.2 Table 3(Elongation)	-	3000	-
Cl. 7.2 Table 3(Yield Stress)	-	3000	-
Cl 13(Length, Width & Thickness)	-	1000	-
Cl 10(Erichsen Cupping)	-	3000	-
Cl 9(Strainage Embrittlement)	-	1000	-
Cl 8(Press)	-	1500	-
Cl 8(Press)	-	1500	-
Cl 9(Strainage Embrittlement)	-	1000	-
Cl 10(Erichsen Cupping)	-	3000	-
Cl 13(Length, Width & Thickness)	-	1000	-
6(Niobium as Nb)	-	500	-
6(Titanium as Ti)	-	500	-
6(Vanadium as V)	-	500	-
6(Micro alloying elements)	-	500	-
7(Tensile Strength-IS:1608(P1))	-	3000	-
7(Yield Strength-IS:1608(P1))	-	3000	-
12(Freedom from defects)	-	1000	-
13(Length - SOP MT-23)	-	1000	-
13(Width-SOP MT-23)	-	1000	-
13(Thickness - SOP MT-23)	-	1000	-
13(Mass)	-	1000	-
15(Marking)	-	1000	-
6.1(Nitrogen%)	-	500	-
6.1(Nitrogen%)	-	500	-
Cl 13(Length, Width & Thickness)	-	1000	-
Cl 7(UTM)	-	3000	-
Cl 7(UTM)	-	3000	-
7(Elongation -IS:1608(P1))	-	3000	-
Cl 8(Press)	-	1000	-
Cl 9(Strainage Embrittlement)	-	1000	-
Cl 10(Erichsen Cupping)	-	1000	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
Cl 7(UTM)	-	3000	-
Cl 8(Press)	-	1000	-
Cl 7(UTM)	-	3000	-
Cl 8(Press)	-	1000	-
Cl 9(Strainage Embrittlement)	-	1000	-
Cl 10(Erichsen Cupping)	-	1000	-
Cl 13(Length, Width & Thickness)	-	1000	-
Cl 7(UTM)	-	3000	-
Cl 9(Strainage Embrittlement)	-	1000	-
Cl 10(Erichsen Cupping)	-	1000	-
Cl 13(Length, Width & Thickness)	-	1000	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1(Nitrogen%)	-	500	-
6.1( Aluminium %)	-	500	-
6.1(Carbon %)	-	500	-
6.1(Manganese %)	-	500	-
6.1(Phosphorus %)	-	500	-
6.1(Sulphur %)	-	500	-
6.1(Silicon %)	-	500	-
6.1( Aluminium %)	-	500	-
Cl. 13(Out of square)	-	1000	-
Cl. 13(Flatness)	-	1000	-
Cl. 13(Camber)	-	1000	-
Cl. 13(Width)	-	1000	-
Cl. 13(Thickness)	-	1000	-
Cl. 12(Freedom from defects)	-	1000	-
Cl. 7.2 Table 3(Elongation)	-	3000	-
Cl. 7.2 Table 3(Yield Stress)	-	3000	-
Cl 13(Length, Width & Thickness)	-	1000	-
Cl 10(Erichsen Cupping)	-	1000	-
Cl 9(Strainage Embrittlement)	-	1000	-
Cl 8(Press)	-	1000	-
Cl 8(Press)	-	1000	-
Cl 9(Strainage Embrittlement)	-	1000	-
Cl 10(Erichsen Cupping)	-	1000	-
Cl 13(Length, Width & Thickness)	-	1000	-
6(Niobium as Nb)	-	500	-
6(Titanium as Ti)	-	500	-
6(Vanadium as V)	-	500	-
6(Micro alloying elements)	-	500	-
7(Tensile Strength-IS:1608(P1))	-	3000	-
7(Yield Strength-IS:1608(P1))	-	3000	-
12(Freedom from defects)	-	1000	-
13(Length - SOP MT-23)	-	1000	-
13(Width-SOP MT-23)	-	1000	-
13(Thickness - SOP MT-23)	-	1000	-
13(Mass)	-	1000	-
15(Marking)	-	1000	-
6.1(Nitrogen%)	-	500	-
6.1(Nitrogen%)	-	500	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 11169 : Part 2 (1989)

Steels for cold heading/cold extrusion applicationsspecification: Part 2 stainless steels

STEELS FOR COLD HEADING/COLD EXTRUSION APPLICATIONS

20250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1,6.2 Table 2(Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Other(Titanium)- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7(FREEDOM FROM DEFECTS)	-	1000	-
8.2, table 5(i) Yield stess/.2% Proof stress, Mpa)	-	2000	-
8.2, table 5(ii)Ultimate Tensile Strength, Mpa)	-	3000	-
8.2, table 5(iii)Elongation, %)	-	2000	-
8.1, Table 4(iv) Reduction in area)	-	2000	-
8.2, table 5(v)Impact strength, J)	-	5000	-
9(CORROSION RESISTANCE)	-	2000	-
Clause 6.1 & 12.1(Titanium)	-	500	-
Clause 6.1 & 12.1(Molybdenum)	-	500	-
Clause 6.1 & 12.1(Nickel)	-	500	-
Clause 6.1 & 12.1(Chromium)	-	500	-
Clause 6.1 & 12.1(Silicon)	-	500	-
Clause 6.1 & 12.1(Phosphorous)	-	500	-
Clause 6.1 & 12.1(Sulphur)	-	500	-
Clause 6.1 & 12.1(Manganese)	-	500	-
Clause 6.1 & 12.1(Carbon)	-	500	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 11169 : Part 1 (2022)

Specification for steels for cold heading cold extrusion applications: Part 1 wrought carbon and low alloy steels

STEELS FOR COLD HEADING/COLD EXTRUSION APPLICATIONS

20250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
17(Shape, Dimensions and tolerances)	-	2000	-
8.1(Tensile Test)	-	3000	-
8.1(Hardness Test)	-	2000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	3000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	3000	-
Cl.4.3,7.2 & Table-A.2(Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Aluminium- Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl. 7(Carbon)	-	500	-
Cl. 7(Sulphur)	-	500	-
Cl. 7(Phosphorous)	-	500	-
Cl. 7(Manganese)	-	500	-
Cl. 7(Silicon)	-	500	-
Cl. 7(Nickel)	-	500	-
Cl. 7(Chromium)	-	500	-
Cl. 7(Aluminium)	-	500	-
Cl. 7(Molybdenum)	-	500	-
Cl. 7(Boron)	-	500	-
Cl. 7(Copper)	-	500	-
Cl. 7(Cr+Ni+Mo)	-	500	-
Cl. 7(Sn)	-	500	-
Cl. 7(V)	-	500	-
Cl. 7(Cr+Ni+Cu+Sn+Mo+V)	-	500	-
17(Shape, Dimensions and tolerances)	-	2000	-
8.1(Tensile Test)	-	3000	-
8.1(Hardness Test)	-	2000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	3000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	3000	-
Cl.4.3,7.2 & Table-A.2(Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Aluminium- Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl. 7(Carbon)	-	500	-
Cl. 7(Sulphur)	-	500	-
Cl. 7(Phosphorous)	-	500	-
Cl. 7(Manganese)	-	500	-
Cl. 7(Silicon)	-	500	-
Cl. 7(Nickel)	-	500	-
Cl. 7(Chromium)	-	500	-
Cl. 7(Aluminium)	-	500	-
Cl. 7(Molybdenum)	-	500	-
Cl. 7(Boron)	-	500	-
Cl. 7(Copper)	-	500	-
Cl. 7(Cr+Ni+Mo)	-	500	-
Cl. 7(Sn)	-	500	-
Cl. 7(V)	-	500	-
Cl. 7(Cr+Ni+Cu+Sn+Mo+V)	-	500	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

Carbon Steel Billets (Standard Quality)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
9( FREEDOM FROM DEFECTS)	-	300	-
10.1.a)( Macro examination IS 11371)	-	300	-
10.1.b)( Sulphur print tests IS 12037)	-	300	-
11 & 12(DIMENSIONS and Tolerances)	-	300	-
11(Dimensions)	-	300	-
10.2(Bend)	-	300	-
10.3(Chamber)	-	300	-
11(Dimensions)	-	300	-
10.2(Bend)	-	1000	-
10.3(Chamber)	-	300	-
Clause 6.1.1(IS 2831 : 2012)	-	300	-
Cl. 11, 12 Table 3(Thickness )	-	300	-
Cl. 11, 12 Table 3(Width Across Flat)	-	300	-
Clause 9.4(Camber)	-	300	-
Clause 9.3(Bend)	-	300	-
Clause 6.1.1(By calculation)	-	300	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	300	-
Clause 6.1.1(By calculation)	-	300	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	200	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	200	-
Clause 6.1.1(Carbon Equivalent (CE))	-	200	-
Table 1 Note 2(Nb+V+Ti)	-	200	-
8(Selection of Test sample)	-	200	-
13(Marking)	-	200	-
Clause 6.1.1(Carbon Equivalent (CE))	-	200	-
Table 1 Note 2(Nb+V+Ti)	-	200	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 9550 (2001)

Bright steel bars - Specification (First Revision)

Bright Steel Bars

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6(Parameter as per requiremnt of purchaser.)	-	1000	-
7(Mechancial Properties)	-	2000	-
8.1 and 8.2(Dimensions and Tolerances, mm)	-	1000	-
8.2.3(Straightness Tolerances)	-	1000	-
9.1(Decarburisation)	-	2000	-
13(Surface Protection)	-	1000	-
14.1(Marking)	-	1000	-
14.1(Marking)	-	1000	-
8(DIMENSIONS AND TOLERANCES)	-	1000	-
7(MECHANICAL PROPERTIES)	-	1000	-
Cl.6(Parameter as per requiremnt of purchaser.)	-	-	-
7(Mechancial Properties)	-	-	-
8.1 and 8.2(Dimensions and Tolerances, mm)	-	-	-
8.2.3(Straightness Tolerances)	-	-	-
9.1(Decarburisation)	-	-	-
13(Surface Protection)	-	-	-
14.1(Marking)	-	-	-
14.1(Marking)	-	-	-
8(DIMENSIONS AND TOLERANCES)	-	-	-
7(MECHANICAL PROPERTIES)	-	-	-

26 Oct, 2025

-
Included w.e.f. 23.08.2024

IS 5206 (1983)

Specification for covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels (First Revision)

16500 View breakup
For BIS samples : BIS approved Testing charges. For others: Rs.21000/- [ Rs.17000/-for Mechanical, Rs.4000/- for Chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Size (Diameter))	-	500	-
5.3(Length)	-	500	-
6.1(Bare length-Contact End,)	-	500	-
6.2(Bare Length-Arc Striking End)	-	500	-
6.2(Bare Length Qualitative)	-	500	-
6.3(Concentricity)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Carbon)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Chromium)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Nickel)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Molybdenum)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Neobium)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Manganese)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Phosphorus)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Sulphur)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Copper)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Silicon)	-	500	-
8.2(Weld Tensile test)	-	2000	-
8.2(Percentage Elongation)	-	500	-
8.2.4(Sample preparation)	-	5000	-
8.3(Fillet weld test)	-	1200	-
8.3.3(Macro examination)	-	2000	-

26 Oct, 2025

-
E13, E16, E18, E19, E20, E23, E25, E29

IS 6419 (1996)

Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

20000 View breakup
Rs.20000/- [ Rs.15000/-for Physical, Rs.5000/- for Chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Copper Content of Coated Wire or Rod)	-	500	-
14.1 Table 7(Carbon-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Manganese-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Silicon-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Phosphorous-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Sulphur-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Nickel-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Chromium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Copper-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Molybdenum-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Vanadium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Titanium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Aluminium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Mo+Ni+Cr-Relevant parts of IS 228)	-	500	-
5(Diameter)	-	500	-
6(Reels for Wire)	-	500	-
7(Reeling Condition)	-	500	-
8(Dimension of Spools, Rims & Coils)	-	1500	-
10.1(Finish)	-	500	-
10.2.2 Table 6(Cast- As per Cl.10.2.2 )	-	500	-
10.2.3 Table 6(Helix- As per Cl.10.2.3 )	-	500	-
10.2.1(Welding rods and bare electrodes for gas shielded arc welding of structural steel)	-	1000	-
14.2(Soundness test)	-	1000	-
14.3.2(Yield Stress)	-	1000	-
14.3.2(UTS)	-	1000	-
14.3.2(% of Elongation)	-	1000	-
14.3.3(Impact Test)	-	3000	-
10.2.1 Table 5(Tensile Strength-IS 1608(P-1))	-	1000	-

26 Oct, 2025

-
S1, S2, S3, S4, S5, S6

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

National Test House (NR) - NTH, Ghaziabad

Kamla Nehru Nagar,Ghaziabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

9999472699 nthnr-ca@nic.in

Scope List