BIS - LIMS (Laboratory Information Management System)

National Test House (NR) - NTH, Ghaziabad

Kamla Nehru Nagar,Ghaziabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

9999472699 director-gzb@nth.gov.in

Scope List

Reset

82 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 11169 : Part 2 (1989)

Steels for cold heading/cold extrusion applicationsspecification: Part 2 stainless steels

STEELS FOR COLD HEADING/COLD EXTRUSION APPLICATIONS

20250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1,6.2 Table 2(Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Nickel- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Chromium- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Molybdenum- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
6.1,6.2 Table 2(Other(Titanium)- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7(FREEDOM FROM DEFECTS)	-	1000	-
8.2, table 5(i) Yield stess/.2% Proof stress, Mpa)	-	2000	-
8.2, table 5(ii)Ultimate Tensile Strength, Mpa)	-	3000	-
8.2, table 5(iii)Elongation, %)	-	2000	-
8.1, Table 4(iv) Reduction in area)	-	2000	-
8.2, table 5(v)Impact strength, J)	-	5000	-
9(CORROSION RESISTANCE)	-	2000	-
Clause 6.1 & 12.1(Titanium)	-	500	-
Clause 6.1 & 12.1(Molybdenum)	-	500	-
Clause 6.1 & 12.1(Nickel)	-	500	-
Clause 6.1 & 12.1(Chromium)	-	500	-
Clause 6.1 & 12.1(Silicon)	-	500	-
Clause 6.1 & 12.1(Phosphorous)	-	500	-
Clause 6.1 & 12.1(Sulphur)	-	500	-
Clause 6.1 & 12.1(Manganese)	-	500	-
Clause 6.1 & 12.1(Carbon)	-	500	-

-
Included w.e.f. 23.08.2024

IS 11169 : Part 1 (2022)

Specification for steels for cold heading cold extrusion applications: Part 1 wrought carbon and low alloy steels

STEELS FOR COLD HEADING/COLD EXTRUSION APPLICATIONS

20250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
17(Shape, Dimensions and tolerances)	-	2000	-
8.1(Tensile Test)	-	3000	-
8.1(Hardness Test)	-	2000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	3000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	3000	-
Cl.4.3,7.2 & Table-A.2(Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Aluminium- Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl. 7(Carbon)	-	500	-
Cl. 7(Sulphur)	-	500	-
Cl. 7(Phosphorous)	-	500	-
Cl. 7(Manganese)	-	500	-
Cl. 7(Silicon)	-	500	-
Cl. 7(Nickel)	-	500	-
Cl. 7(Chromium)	-	500	-
Cl. 7(Aluminium)	-	500	-
Cl. 7(Molybdenum)	-	500	-
Cl. 7(Boron)	-	500	-
Cl. 7(Copper)	-	500	-
Cl. 7(Cr+Ni+Mo)	-	500	-
Cl. 7(Sn)	-	500	-
Cl. 7(V)	-	500	-
Cl. 7(Cr+Ni+Cu+Sn+Mo+V)	-	500	-
17(Shape, Dimensions and tolerances)	-	2000	-
8.1(Tensile Test)	-	3000	-
8.1(Hardness Test)	-	2000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	3000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	3000	-
Cl.4.3,7.2 & Table-A.2(Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Aluminium- Established instrumental/ chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl.4.3,7.2 & Table-A.2(Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	500	-
Cl. 7(Carbon)	-	500	-
Cl. 7(Sulphur)	-	500	-
Cl. 7(Phosphorous)	-	500	-
Cl. 7(Manganese)	-	500	-
Cl. 7(Silicon)	-	500	-
Cl. 7(Nickel)	-	500	-
Cl. 7(Chromium)	-	500	-
Cl. 7(Aluminium)	-	500	-
Cl. 7(Molybdenum)	-	500	-
Cl. 7(Boron)	-	500	-
Cl. 7(Copper)	-	500	-
Cl. 7(Cr+Ni+Mo)	-	500	-
Cl. 7(Sn)	-	500	-
Cl. 7(V)	-	500	-
Cl. 7(Cr+Ni+Cu+Sn+Mo+V)	-	500	-

-
Included w.e.f. 23.08.2024

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

Carbon Steel Billets (Standard Quality)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6.1, Table 1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
9( FREEDOM FROM DEFECTS)	-	300	-
10.1.a)( Macro examination IS 11371)	-	300	-
10.1.b)( Sulphur print tests IS 12037)	-	300	-
11 & 12(DIMENSIONS and Tolerances)	-	300	-
11(Dimensions)	-	300	-
10.2(Bend)	-	300	-
10.3(Chamber)	-	300	-
11(Dimensions)	-	300	-
10.2(Bend)	-	1000	-
10.3(Chamber)	-	300	-
Clause 6.1.1(IS 2831 : 2012)	-	300	-
Cl. 11, 12 Table 3(Thickness )	-	300	-
Cl. 11, 12 Table 3(Width Across Flat)	-	300	-
Clause 9.4(Camber)	-	300	-
Clause 9.3(Bend)	-	300	-
Clause 6.1.1(By calculation)	-	300	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	300	-
Clause 6.1.1(By calculation)	-	300	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	200	-
Table 1 Note 2(Any Instrumental Method/Chemical Method)	-	200	-
Clause 6.1.1(Carbon Equivalent (CE))	-	200	-
Table 1 Note 2(Nb+V+Ti)	-	200	-
8(Selection of Test sample)	-	200	-
13(Marking)	-	200	-
Clause 6.1.1(Carbon Equivalent (CE))	-	200	-
Table 1 Note 2(Nb+V+Ti)	-	200	-

-
Included w.e.f. 23.08.2024

IS 9550 (2001)

Bright steel bars - Specification (First Revision)

Bright Steel Bars

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6(Parameter as per requiremnt of purchaser.)	-	1000	-
7(Mechancial Properties)	-	2000	-
8.1 and 8.2(Dimensions and Tolerances, mm)	-	1000	-
8.2.3(Straightness Tolerances)	-	1000	-
9.1(Decarburisation)	-	2000	-
13(Surface Protection)	-	1000	-
14.1(Marking)	-	1000	-
14.1(Marking)	-	1000	-
8(DIMENSIONS AND TOLERANCES)	-	1000	-
7(MECHANICAL PROPERTIES)	-	1000	-
Cl.6(Parameter as per requiremnt of purchaser.)	-	-	-
7(Mechancial Properties)	-	-	-
8.1 and 8.2(Dimensions and Tolerances, mm)	-	-	-
8.2.3(Straightness Tolerances)	-	-	-
9.1(Decarburisation)	-	-	-
13(Surface Protection)	-	-	-
14.1(Marking)	-	-	-
14.1(Marking)	-	-	-
8(DIMENSIONS AND TOLERANCES)	-	-	-
7(MECHANICAL PROPERTIES)	-	-	-

-
Included w.e.f. 23.08.2024

IS 5206 (1983)

Specification for covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels (First Revision)

16500 View breakup
For BIS samples : BIS approved Testing charges. For others: Rs.21000/- [ Rs.17000/-for Mechanical, Rs.4000/- for Chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Size (Diameter))	-	500	-
5.3(Length)	-	500	-
6.1(Bare length-Contact End,)	-	500	-
6.2(Bare Length-Arc Striking End)	-	500	-
6.2(Bare Length Qualitative)	-	500	-
6.3(Concentricity)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Carbon)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Chromium)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Nickel)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Molybdenum)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Neobium)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Manganese)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Phosphorus)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Sulphur)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Copper)	-	500	-
Table 1 , Clause 9.1 , Clause 1.1 , Clause 8.1(Silicon)	-	500	-
8.2(Weld Tensile test)	-	2000	-
8.2(Percentage Elongation)	-	500	-
8.2.4(Sample preparation)	-	5000	-
8.3(Fillet weld test)	-	1200	-
8.3.3(Macro examination)	-	2000	-

-
E13, E16, E18, E19, E20, E23, E25, E29

IS 6419 (1996)

Welding rods and bare electrodes for gas shielded arc welding of structural steel - Specification (First Revision)

20000 View breakup
Rs.20000/- [ Rs.15000/-for Physical, Rs.5000/- for Chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Copper Content of Coated Wire or Rod)	-	500	-
14.1 Table 7(Carbon-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Manganese-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Silicon-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Phosphorous-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Sulphur-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Nickel-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Chromium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Copper-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Molybdenum-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Vanadium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Titanium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Aluminium-Relevant parts of IS 228)	-	500	-
14.1 Table 7(Mo+Ni+Cr-Relevant parts of IS 228)	-	500	-
5(Diameter)	-	500	-
6(Reels for Wire)	-	500	-
7(Reeling Condition)	-	500	-
8(Dimension of Spools, Rims & Coils)	-	1500	-
10.1(Finish)	-	500	-
10.2.2 Table 6(Cast- As per Cl.10.2.2 )	-	500	-
10.2.3 Table 6(Helix- As per Cl.10.2.3 )	-	500	-
10.2.1(Welding rods and bare electrodes for gas shielded arc welding of structural steel)	-	1000	-
14.2(Soundness test)	-	1000	-
14.3.2(Yield Stress)	-	1000	-
14.3.2(UTS)	-	1000	-
14.3.2(% of Elongation)	-	1000	-
14.3.3(Impact Test)	-	3000	-
10.2.1 Table 5(Tensile Strength-IS 1608(P-1))	-	1000	-

-
S1, S2, S3, S4, S5, S6

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

8000 View breakup
For BIS samples: Rs.8410/-, For others: Rs.11000/- [Rs.6000/- for physical, Rs.5000/- for chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.1(Average Compressive Strength)	-	1200	-
16.1(Compressive Strength of Individual Samples )	-	1000	-
16.1(Compressive Strength of Individual Samples )	-	1000	-

-
Water for construction purposes

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	500	-
10.1(Surface Finish)	-	500	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	1000	-
10.7(Sulphated Ash Content)	-	3000	-
5(CLASSIFICATION OF PIPES)	-	1000	-
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	1000	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	1000	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	1000	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	1000	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	1000	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	1000	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	1000	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	1000	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	1000	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	1000	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	1000	-
7.2.1(DIMENSIONS-Socket)	-	1000	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	1000	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	1000	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	1000	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	1000	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	1000	-
8(SEALING RINGS)	-	1000	-
9.1(PIPE ENDS)	-	1000	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	1000	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	1000	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	1000	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	2000	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	2000	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	1000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	5000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	5000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	5000	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	5000	-
11.2(Resistance to External Blows at 0°C)	-	2000	-
10.3(Effect on Water Test)	-	5000	-
6.1.2(PVC Resin)	-	2000	-
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	2000	-
7.1.4(Length)	-	1000	-
6.1.1(VCM Content)	-	2000	-
7.2.1.2b(Maximum inner diameter of groove)	-	1000	-
13.1(Marking)	-	500	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	5000	-

-
Included w.e.f. 23.08.2024

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	250	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	250	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	250	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	250	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	250	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	250	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	250	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	250	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	250	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	250	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	250	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	250	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	250	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	250	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	250	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	250	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	250	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	250	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	250	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	250	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	250	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	250	-
10.1 g)(High voltage test - IS10810:Part 45)	-	250	-
6.4(size of street lighting conductor)	-	250	-
6.5(Size of messenger conductor )	-	250	-
4.1(Phase/Street Lighting conductor)	-	250	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	250	-
6.2(No of strands)	-	250	-
5.1(Insulation)	-	250	-
6.1(Flexibility class)	-	250	-
6.2(Compactness)	-	250	-
6.2(Surface)	-	250	-
6.3(Protective barrier)	-	250	-
6.6(Direction of outer layer)	-	250	-
7.2( Thickness of insulation)	-	250	-
7.3(Tolerance on thickness of insulation )	-	250	-
7.5(Colour of the insulation )	-	250	-
9.1(Assembly (Laying up))	-	250	-
9.3(Direction of lay)	-	250	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	250	-

-
-

IS 4159 (2021)

Mineral Filled Sheathed Heating Elements

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
"Cl. 6 IS 4159:2021"(Classification)	-	500	-
"Cl. 8 IS 4159:2021"(Protection against access to live parts)	-	500	-
"Cl. 10 IS 4159:2021"(Power Input and Current)	-	500	-
"Cl. 11 IS 4159:2021"(Heating)	-	500	-
"Cl. 13 IS 4159:2021"(Leakage Current & Electrical Strength at Operating Temperature)	-	500	-
"Cl. 14 IS 4159:2021"(Transient Over Voltage)	-	500	-
"Cl. 15 IS 4159:2021"(Moisture Resistance)	-	500	-
"Cl. 16 IS 4159:2021"(Leakage Current and Electric strength)	-	500	-
"Cl. 18 IS 4159:2021"(Endurance)	-	500	-
"Cl. 19 IS 4159:2021"(Abnormal Operation)	-	500	-
"Cl. 20 IS 4159:2021"(Stability and mechanical Hazards)	-	500	-
"Cl. 21 IS 4159:2021"(Mechanical Strength)	-	500	-
"Cl. 22 IS 4159:2021"(Construction)	-	500	-
"Cl. 23 IS 4159:2021"(Internal Wiring)	-	500	-
"Cl. 24 IS 4159:2021"(Components)	-	500	-
"Cl. 25 IS 4159:2021"(Supply Connections and External Flexible Cables and Cords)	-	500	-
"Cl. 26 IS 4159:2021"(Terminal For External Conductors)	-	500	-
"Cl. 27 IS 4159:2021"(Provision For Earthing)	-	500	-
"Cl. 28 IS 4159:2021"(Screws and Connections)	-	500	-
"Cl. 29 IS 4159:2021"(Creepage Distances, Clearances And Distances Through Insulation)	-	500	-
"Cl. 30 IS 4159:2021"(Resistance To Heat, Fire And Tracking)	-	500	-
"Cl. 31 IS 4159:2021"(Resistance To Rusting)	-	500	-

-
Included w.e.f. 23.08.2024 Exclusion: Leakage and hydrostatic strength (for oil heating elements), Cl. 9 (Starting of motor operated appliances), Cl. 17 (Overload protection of transformers and associated circuits.)

IS 1293 (2019)

Plugs and socket - Outlets of rated Voltage up to and including 250 Volts and rated current up to and including 16 amperes - Specification (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Ratings)	-	500	-
7.1.1(Accessories Classification)	-	500	-
7.1.2(Accessories Classification)	-	500	-
7.1.3(Accessories Classification)	-	500	-
7.1.4(Accessories Classification)	-	500	-
7.1.5(Accessories Classification)	-	500	-
7.2.1(Socket-Outlets Classification)	-	500	-
7.2.2(Socket-Outlets Classification)	-	100	-
7.2.3(Socket-Outlets Classification)	-	100	-
7.2.4(Socket-Outlets Classification)	-	100	-
7.3(Plug Classification)	-	100	-
8.1(MARKING)	-	100	-
8.8(MARKING)	-	100	-
8.9(MARKING)	-	100	-
8.2(MARKING)	-	100	-
8.3(Marking)	-	100	-
8.4(Marking)	-	100	-
8.5(Marking)	-	100	-
8.6(Marking)	-	100	-
8.7(Marking)	-	100	-
9.1(CHECKING OF DIMENSIONS)	-	500	-
9.2(CHECKING OF DIMENSIONS)	-	500	-
9.3(CHECKING OF DIMENSIONS)	-	500	-
9.1 (a)(Dimension of plug (6/10A))	-	500	-
9.1 (b)(Dimension of plug (6/10A))	-	500	-
9.1 (c)(Dimension of plug (6/10A))	-	500	-
9.1 (d)(Dimension of plug (6/10A))	-	500	-
9.1 (e)(Dimension of plug (6/10A))	-	500	-
9.1 (f)(Dimension of plug (6/10A))	-	500	-
9.1 (g)(Dimension of plug (6/10A))	-	500	-
9.1 (h)(Dimension of plug (16 A))	-	500	-
9.1 (i)(Dimension of plug (16 A))	-	500	-
9.1 (j)(Dimension of plug (16 A))	-	500	-
10.1(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
10.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
10.3(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
10.4(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
10.5(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
10.6(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
10.7(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
11.1(PROVISIONS FOR EARTHING)	-	500	-
11.2(PROVISIONS FOR EARTHING)	-	500	-
11.3(PROVISIONS FOR EARTHING)	-	500	-
11.4(PROVISIONS FOR EARTHING)	-	500	-
11.5(PROVISIONS FOR EARTHING)	-	500	-
11.6(PROVISIONS FOR EARTHING)	-	500	-
12.1.1(TERMINALS)	-	500	-
12.1.2(TERMINALS)	-	500	-
12.2.1(TERMINALS)	-	500	-
12.2.2(TERMINALS)	-	500	-
12.2.3(TERMINALS)	-	500	-
12.2.4(TERMINALS)	-	500	-
12.2.5(TERMINALS)	-	500	-
12.2.6(TERMINALS)	-	500	-
12.2.7(TERMINALS)	-	500	-
12.2.8(TERMINALS)	-	500	-
12.2.9(TERMINALS)	-	500	-
12.2.10(TERMINALS)	-	500	-
12.2.11(TERMINALS)	-	500	-
12.3.1(TERMINALS)	-	500	-
12.3.2(TERMINALS)	-	500	-
12.3.3(TERMINALS)	-	500	-
12.3.4(TERMINALS)	-	500	-
12.3.5(TERMINALS)	-	500	-
12.3.6(TERMINALS)	-	500	-
12.3.7(TERMINALS)	-	500	-
12.3.8(TERMINALS)	-	500	-
12.3.9(TERMINALS)	-	500	-
12.3.10(TERMINALS)	-	500	-
12.3.11(TERMINALS)	-	500	-
12.3.12(TERMINALS)	-	500	-
13.1(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.2(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.3(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.4(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.5(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.6(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.7.1(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	500	-
13.7.2 (CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	500	-
13.7.3 (CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	500	-
13.8(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.9(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.11(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.12(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.13(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.14(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.15(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.16(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.17(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.18(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.19(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.21(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.22(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
13.23(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	500	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.4(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.5(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.6(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.7(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.8(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.9(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.10.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.10.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.10.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.11(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.12(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.13(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.15(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.16(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.17(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.18(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.19(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.21(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.22(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.23(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.23.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.23.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.24(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.25(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
14.26(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	500	-
15(INTERLOCKED SOCKET-OUTLETS)	-	500	-
16.1(RESISTANCE TO AGEING,)	-	500	-
16.2.1(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	500	-
16.2.1.1(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	500	-
16.2.1.2(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	500	-
16.2.2(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	500	-
16.3(Resistance to Humidity)	-	500	-
17.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
17.2(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	500	-
18(OPERATION OF EARTHING CONTACTS)	-	500	-
19(TEMPERATURE RISE)	-	500	-
19.3(TEMPERATURE RISE)	-	500	-
20(BREAKING CAPACITY)	-	500	-
21(NORMAL OPERATION)	-	500	-
21(NORMAL OPERATION)	-	500	-
21(NORMAL OPERATION)	-	500	-
22.1(Verification of the Maximum Withdrawal Force)	-	500	-
22.2(Verification of Minimum Withdrawal Force)	-	500	-
23.1(FLEXIBLE CABLES AND THEIR CONNECTION)	-	500	-
23.2(FLEXIBLE CABLES AND THEIR CONNECTION)	-	500	-
23.3(FLEXIBLE CABLES AND THEIR CONNECTION)	-	500	-
23.4(FLEXIBLE CABLES AND THEIR CONNECTION)	-	500	-
24.1(MECHANICAL STRENGTH For all kinds of fixed socket-outlets )	-	500	-
24.2(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	500	-
24.3(MECHANICAL STRENGTH for fixed socket-outlets with a main part intended to be mounted directly on a surface)	-	500	-
24.4(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	500	-
24.5(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	500	-
24.6(MECHANICAL STRENGTH For screwed glands of accessories having an IP code higher than IP20)	-	500	-
24.7(MECHANICAL STRENGTH For plug pins provided with insulating sleeves)	-	500	-
24.8(MECHANICAL STRENGTH For shuttered socket-outlets)	-	500	-
24.9(MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	500	-
24.1(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	500	-
24.11(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	500	-
24.12(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	500	-
24.13(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	500	-
24.14.1(MECHANICAL STRENGTH For fixed socket-outlets)	-	500	-
24.14.2(MECHANICAL STRENGTH For fixed socket-outlets)	-	500	-
24.14.3(MECHANICAL STRENGTH For plugs and portable socket-outlets)	-	500	-
24.15(MECHANICAL STRENGTH )	-	500	-
24.16(MECHANICAL STRENGTH )	-	500	-
24.17(MECHANICAL STRENGTH)	-	500	-
24.18(MECHANICAL STRENGTH)	-	500	-
24.19(MECHANICAL STRENGTH)	-	500	-
25.1(RESISTANCE TO HEAT Accessories and surface mounting boxes)	-	500	-
25.2(RESISTANCE TO HEAT Parts of insulating material necessary to retain current-carrying parts of the earthing circuit in position, as well as parts of the front surface zone of thermoplastic material)	-	500	-
25.3(RESISTANCE TO HEAT Parts of insulating material not necessary to retain current-carrying parts and parts of the earthing circuit in position, even though they are in contact with them)	-	500	-
25.4(RESISTANCE TO HEAT )	-	500	-
26.1(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
26.2(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
26.3(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
26.4(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
26.5(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
26.6(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
26.7(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	500	-
27.1(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	500	-
27.2(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	500	-
27.3(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	500	-
28.1.1(Resistance to Abnormal Heat and to Fire Glow-Wire Test)	-	500	-
28.1.2(Resistance to Abnormal Heat and to Fire for plugs with pins provided with insulating sleeves)	-	500	-
28.2(Resistance to Tracking For accessories other than IP code higher than IPX0 parts of insulating material retaining live parts in position)	-	500	-
29(RESISTANCE TO RUSTING)	-	500	-
30.1(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Pressure Test at High Temperature)	-	500	-
30.2(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Static Damp Heat Test)	-	500	-
30.3(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Tests at Low Temperature)	-	500	-
30.4(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Impact Test at Low Temperature)	-	500	-

-
Included w.e.f. 23.08.2024

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

20000 View breakup
Rs.20000/- for non-mining single core cable, Rs.22500 for mining single core cable and Rs.2500 for each extra core.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(MATERIALS : ARMGURING)	-	500	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	500	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	300	-
16.5(Oxygen Index Test)	-	300	-
16.1(Temperature Index)	-	300	-
16.9(Test for Halogen Acid Gas Evolution)	-	200	-
13.6 a)(ARMOURING: Tensile Strength)	-	100	-
3.1(MATERIALS : CONDUCTOR)	-	100	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	200	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	200	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	200	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	100	-
6.1(MATERIALS : ARMGURING)	-	100	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	0	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	0	-
8.1(CONSTRUCTION : CONDUCTOR)	-	100	-
8.2(CONSTRUCTION : CONDUCTOR)	-	100	-
9.1(INSULATION )	-	100	-
9.2(INSULATION : Thickness of Insulation)	-	200	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	100	-
9.4(INSULATION : Application of Insulation)	-	100	-
10.1(CORE IDENTIFICATION)	-	100	-
10.2(CORE IDENTIFICATION)	-	0	-
10.3(CORE IDENTIFICATION)	-	0	-
10.3.1(Arrangement of Marking)	-	100	-
11.1(LAYING UP OF CORES)	-	100	-
11.2(LAYING UP OF CORES)	-	0	-
12.1(INNER SHEATH)	-	100	-
12.2(INNER SHEATH)	-	0	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	300	-
13.1.1(ARMOURING : Application)	-	200	-
13.1.2(Armouring: Coverage )	-	200	-
13.1.3(ARMOURING : Direction of lay )	-	200	-
13.1.4(ARMOURING : Application)	-	0	-
13.2(ARMOURING : Type of Armour)	-	200	-
13.2.1(ARMOURING : Type of Armour)	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	200	-
13.3(Armouring : Dimensions -Formed wire )	-	200	-
13.4(ARMOURING : Joints)	-	200	-
13.5.1(ARMOURING : Resistance)	-	500	-
13.5.2(ARMOURING : Resistance)	-	500	-
13.6 b)(ARMOURING: Elongation )	-	100	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	100	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	100	-
13.6 g)(ARMOURING: Resistivity)	-	200	-
14.1(OUTER SHEATH)	-	100	-
14.2(OUTER SHEATH)	-	0	-
14.3(OUTER SHEATH : Colour )	-	100	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	300	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	100	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	500	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	500	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	500	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	500	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	500	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	100	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	100	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	100	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	200	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	200	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	200	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	200	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	200	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	200	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	200	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	100	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	200	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	200	-
15.1 d)4)(Hot deformation : Insulation )	-	200	-
15.1 d)4)(Hot deformation : Sheath )	-	200	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	200	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	200	-
15.1 d)6)(Heat shock test- Insulation )	-	200	-
15.1 d)6)(Heat shock test- sheath )	-	200	-
15.1 d)7)(Thermal stability- insulation )	-	200	-
15.1 d)7)(Thermal stability- Sheath )	-	200	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	0	-
15.1 e)(Insulation resistance test : IR Constant )	-	0	-
15.1 f)(High voltage test ( water immersion test ))	-	0	-
15.1 g)(High voltage test at room temperature)	-	500	-
15.1 g)(High voltage test at room temperature)	-	0	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	500	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	500	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	500	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	500	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	500	-
16.1(DETAILS OF TESTS : General)	-	0	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	0	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1000	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	1000	-
16.4(Flammability Test)	-	200	-
16.6(Flame Retardance Test on Single Cables)	-	100	-
16.7(Flame Retardance Test on Bunched Cables)	-	100	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	100	-
17.2(IDENTIFICATION : Cable Identification)	-	100	-
17.2.1(IDENTIFICATION : Cable Identification)	-	0	-
17.3(IDENTIFICATION : Cable Code)	-	100	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	500	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	500	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	200	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	200	-
16.4(Flammability Test- Un affected portion)	-	100	-
16.4(Flammability Test- Period of Burning)	-	100	-
9.3(Minimum Thickness of Reduce core insulation)	-	100	-
9.2(Thickness of Reduce core insulation)	-	100	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	100	-
Cl No. 16.10(Smoke density test)	-	200	-
Cl No. 16.8(Test for specific optical density of smoke)	-	200	-
Table 4(Copper purity test)	-	200	-

-
-

IS 8978 (1992)

Specification for electric instantaneous water heaters (Second Revision)

15000 View breakup
For BIS samples: BIS approved Testng charges. For Others: Rs.15000 (Inclusive of safety testing charges as per IS 302-2-35 @ Rs.5000/-)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7 of IS 302-2-35:2017(Marking)	-	100	-
Cl.7 of IS 302-2-35:2017(Marking)	-	0	-
Cl.7 of IS 302-2-35:2017(Marking)	-	0	-
Cl.7 of IS 302-2-35:2017(Marking)	-	0	-
Cl.7 of IS 302-2-35:2017(Marking)	-	0	-
Cl.6 of IS 302-2-35:2017(Classification)	-	100	-
Cl.6 of IS 302-2-35:2017(Classification)	-	0	-
Cl.8 of IS 302-2-35:2017(Protection Against Access To Live Parts)	-	1000	-
Cl.10 of IS 302-2- 35:2011(Power Input & Current )	-	1000	-
Cl.11 of 302-2-35:2017(Heating)	-	1000	-
Cl.11 of 302-2-35:2017(Heating)	-	0	-
Cl.11 of 302-2-35:2017(Heating)	-	0	-
Cl.11 of 302-2-35:2017(Heating)	-	0	-
Cl.13 of IS 302-2-35:2017(Leakage Current & Electrical Strength at Operating Temperature )	-	500	-
Cl.13 of IS 302-2-35:2017(Leakage Current & Electrical Strength at Operating Temperature )	-	0	-
Cl.14 of IS 302-2-35:2017(Transient Over Voltages )	-	500	-
Cl.15 of IS 302-2-35-2011(Moisture Resistance )	-	100	-
Cl.16 of IS 302-2-35:2011(Leakage Current and Electric Strength)	-	0	-
Cl.16 of IS 302-2-35:2011(Leakage Current and Electric Strength)	-	0	-
Cl.17 IS 302-2-35:2017(Overload Protection of Transformers & Associated circuits )	-	100	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	100	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	0	-
Cl.20 of IS 302-2-35-2011(Stability & Mechanical Hazards )	-	100	-
Cl.21.1 of IS 302-2-35-2011(Mechanical strength)	-	500	-
Cl. 21.2 of IS 302-1:2008(Mechanical strength)	-	0	-
Cl.22 of IS 302-2-35-2011(Construction )	-	500	-
Cl.22 of IS 302-2-35-2011(Construction )	-	0	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	400	-
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	-
Cl.24 of IS 302-2-35:2017(Component )	-	500	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	300	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	100	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	500	-
Cl.28 of IS 302-2-35:2017(Screws and Connections )	-	300	-
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	500	-
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	0	-
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	0	-
Cl.30 of IS 302-2-35: 2011(Resistance to Heat and Fire)	-	500	-
Cl.30.1 of IS 302-1:2008(Resistance to Heat and Fire)	-	0	-
Cl.31 of IS 302-2-35: 2011(Resistance to Rusting )	-	500	-
Cl.30.2 of IS 302-1:2008(Resistance to Heat and Fire)	-	0	-
Cl.29.2 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation : Creepage distance )	-	0	-
Cl.29.1 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation : Clearance distance )	-	0	-
Cl.28 of IS 302-2-35:2017(Screws and Connections )	-	0	-
Cl.27.5 of IS 302-2-35:2017(Provision for Earthing : ECR )	-	0	-
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	0	-
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	-
Cl.25.18 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	-
Cl.25.15 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Cord grip test - displacement )	-	0	-
Cl.25.15 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Cord grip test )	-	0	-
Cl.25.12 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Moulding of supply cord )	-	0	-
Cl.25.10 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Colour of Earthing conductor )	-	0	-
Cl.25.8 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Resistance of supply cord )	-	0	-
Cl.25.5 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Type of attachment )	-	0	-
Cl.25.1 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : connection to the supply mains)	-	0	-
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	-
Cl.24 of IS 302-2-35:2017(Component )	-	500	-
Cl.23 of IS 302-2-35:2017(Internal Wiring ; Colour of earthing conductor)	-	0	-
Cl.22.110 of IS 302-2-35:2017(Construction : Provision for fixing to wall )	-	500	-
Cl.22.109 of IS 302-2-35:2017(Construction : Operation of presure switch of open outlet water heater )	-	0	-
Cl.22.108 of IS 302-2-35:2017(Construction : Temperature of outlet water intended to supply for showring )	-	0	-
Cl.22.107 of IS 302-2-35:2017(Construction : Temperature of outlet )	-	0	-
Cl.22.106 of IS 302-2-35:2017(Construction : Operation of thermal cut out for closed water heater )	-	0	-
Cl.22.104 of IS 302-2-35:2017(Construction : Pressure in open outlet water heaters )	-	0	-
Cl.22.103 of IS 302-2-35:2017(Construction : Pressure relief device operation for closed water heater )	-	0	-
Cl.22.102 of IS 302-2-35:2017(Construction : excessive temperature of outlet )	-	0	-
Cl.22.101 of IS 302-2-35:2017(Construction : Rated pressure of closed water heater )	-	0	-
Cl.22.47 of IS 302-2-35:2017(Construction : Water pressure test )	-	0	-
Cl.22.44 of IS 302-1:2008(Construction : Shape and decoration )	-	0	-
Cl.22.34, Cl 22.35 of IS 302-1:2008(Construction : Shaft of operating Knobs )	-	0	-
Cl.22.33 of IS 302-1:2008(Construction : Direct contact of liquids )	-	0	-
Cl 22.26 ,Cl.22.28, Cl 22.29, Cl 22.30 , Cl 22.31, Cl 22.32 of IS 302-1:2008(Construction : Supplymentry/ double / reinforced insulation for Class II/ Class III appliance )	-	0	-
Cl.22.18 of IS 302-1:2008(Construction : Resistance to corrosion )	-	0	-
Cl.22.17 of IS 302-1:2008(Construction : Spacers )	-	0	-
Cl.22.14 of IS 302-1:2008(Construction : Ragged or sharp edges )	-	0	-
Cl.22.12 of IS 302-1:2008(Construction : Fixing of Handle, knob, grips, levers and similar parts )	-	0	-
Cl.22.11 of IS 302-1:2008(Construction : Fixing of non detachable parts )	-	0	-
Cl.22.7 of IS 302-1:2008(Construction : safeguards against the risk of excessive pressure. )	-	0	-
Cl.22.6 of IS 302-2-35:2017(Construction : size of drain hole )	-	0	-
Cl.22.6 of IS 302-1:2008(Construction : effect of water on 3 insulation )	-	0	-
Cl.22.2 of IS 302-1:2008(Construction : connection to supply mains )	-	0	-
Cl.22.1 of IS 302-1:2008(Construction : IP test )	-	0	-
Cl. 21.2 of IS 302-1:2008(Mechanical strength : prevent penetration by sharp implements. )	-	500	-
Cl.21.1 of IS 302-1:2008(Mechanical strength : Rough handling in normal use)	-	0	-
Cl.20 of IS 302-2-35:2017(Stability & Mechanical Hazards )	-	100	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : effect on container)	-	100	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : High voltage)	-	0	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Temperature rise of insulation of supply cord)	-	0	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Temperature rise of test corner)	-	0	-
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Emission of flames, molten metal ,or poisonous or ignitable gas)	-	0	-
Cl.16 of IS 302-2-35:2017(Leakage Current and Electric Strength (After Humidity))	-	1000	-
Cl.16 of IS 302-2-35:2017(Leakage Current and Electric Strength (After Humidity))	-	0	-
Cl.15 of IS 302-2-35:2017(Moisture Resistance )	-	100	-
Cl.14 of IS 302-2-35:2017(Transient Over Voltages )	-	100	-
Cl.13 of IS 302-2-35:2017(Leakage Current & 3 Strength at Operating Temperature : High voltage )	-	0	-
Cl.11 of 302-2-35:2017(Heating : room temperature)	-	100	-
Cl.11 of 302-2-35:2017(Heating : Insulation of supply cord)	-	0	-
Cl.11 of 302-2-35:2017(Heating : Temperature rise of test corner)	-	0	-
Cl.10 of IS 302-2- 35:2017(Power Input & Current )	-	1000	-
Cl.8 of IS 302-2-35:2017(Protection Against Access To Live Parts)	-	900	-
Cl.7.102 of IS 302-2-35:2017(Marking : Standard mark)	-	100	-
Cl.7.101 of IS 302-2-35:2017(Marking : Woter inlet and outlet idetification)	-	0	-
Cl.7.15 of IS 302-1:2008(Marking : Position of marking)	-	0	-
Cl.7.14 of IS 302-1:2008(Marking ; Legibility and durability)	-	0	-
Cl.7.13 of IS 302-1:2008(Marking : Language)	-	0	-
Cl.7.10 & 7.11 of IS 302-1:2008(Marking : Indication for direction of control)	-	0	-
Cl.7.8 of IS 302-1:2008(Marking : Terminal for connection )	-	0	-
Cl.7.6 of IS 302-1:2008(Marking : Symbols)	-	0	-
Cl.7.1 of IS 302-2-35:2017(Marking : rated pressure)	-	0	-
Cl.7.1 of IS 302-1:2008(Marking : Country of manufacture)	-	0	-
Cl.7.1 of IS 302-1:2008(Marking : IP number )	-	0	-
Cl.7.1 of IS 302-1:2008(Marking : Symbol for class II)	-	0	-
Cl.7.1 of IS 302-1:2008(Marking : Molel or type)	-	0	-
Cl.7.1 of IS 302-1:2008(Marking : Manufacture identification)	-	0	-
Cl.7.1 of IS 302-1:2008(Marking : Rated power input)	-	0	-
Cl.7.1 of IS 302-1:2008(Marking : Nature of supply)	-	0	-
Cl.7.1 of IS 302-1:2008(Marking : Rated Voltage)	-	0	-

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Visual Appearance)	-	1000	-
7.2(Length)	-	1000	-
Clause 7.3(Coiling)	-	1000	-
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	1000	-
7.4.1.2(Ovality)	-	1000	-
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	5000	-
8.2(Longitudinal Reversion Test)	-	2000	-
Clause 8.3(Carbon Black content)	-	2000	-
Cl. 8.3(Carbon Black Dispersion)	-	1000	-
8.4( Melt Flow Rate)	-	2000	-
8.5 (Oxidation Induction Time)	-	2000	-
Clause 8.6(Overall migration (stimulate))	-	5000	-
8.7(Density)	-	1000	-
8.8(Tensile Strength for Butt-fusion)	-	1500	-
8.9 table-6(Elongation at Break)	-	1500	-
8.10(Slow Crack Growth Rate)	-	3000	-
6.2.1(6.1.1 Identification Stripes)	-	500	-
6.2(Colour)	-	500	-
6.1.4(PIPE DESCRIPTION)	-	500	-
6.1.3 (PIPE DESCRIPTION)	-	500	-
6, 6.1.2(PIPE DESCRIPTION)	-	500	-
6, 6.1.1(PIPE DESCRIPTION)	-	500	-
Cl. 8.3(Carbon Black Content)	-	2000	-
5.4(Anti oxydent)	-	2000	-
5.2(Polyethylene Resin)	-	2000	-
5.2(Density)	-	1000	-
5.2(MFI @ 1900C/5.0 Kg)	-	2000	-
5.2(Volatile matter Content)	-	2000	-
Clause 7.1(Visual Apperance)	-	1000	-
7.3(Coiling)	-	1000	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	2000	-
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	2000	-
8.7(Density-IS 7328:2020)	-	1000	-
8.7(Corrected Density- IS 7328:2020)	-	1000	-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	1500	-
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	1500	-
Cl 8.3(Carbon Black Content)	-	2000	-
Cl 8.3(Carbon Black Dispersion)	-	2000	-
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	5000	-
6, 6.1(PIPE DESCRIPTION)	-	1000	-
8.6(Overall migration)	-	5000	-
Clause 8.6(Overall migration (surface of material))	-	5000	-
7()	-	1000	-
Clause 8.3(Carbon Black Dispersion)	-	2000	-
8.3(Carbon black)	-	1000	-

-
Included w.e.f. 23.08.2024 Exclusion: cL.5.3 (Carbon Black Master Batch) row material

IS 3812 (Part 1) (2013)

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

Type-Calcareous Fly Ash / Siliceous Fly Ash

13500 View breakup
Rs.13500/- [ Rs.9500/-for Physical, Rs.4000/- for Chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1 - i(Silicon dioxide (SiO2) plus aluminium oxide (Al2O3) plus ironoxide (Fe2O3) - IS 1727)	-	2000	-
Cl. 6.1, Table 1 - ii(Silicon dioxide (SiO2) - IS 1727)	-	1000	-
Cl. 6.1, Table 1 - iii(Reactive Silica - Annex B)	-	2000	-
Cl. 6.1, Table 1 - iv(Magnesium oxide (MgO) - IS 1727)	-	1000	-
Cl. 6.1, Table 1 - v( Total sulphur as sulphur trioxide (SO3) - IS 1727)	-	1000	-
Cl. 6.1, Table 1 - vi( Available alkalis as equivalent sodium oxide (Na2O) - Annex C)	-	1000	-
Cl. 6.1, Table 1 - vii( Total Chlorides - IS 4032)	-	1000	-
Cl. 6.1, Table 1 - viii( Loss on ignition - IS 1727)	-	1000	-
Cl. 6.2(Moisture content of the fly ash when supplied in dry condition - Annex D)	-	1000	-
7.1-Table 2(i)(PHYSICAL REQUIREMENTS-Fineness)	-	1000	-
7.1-Table 2(ii)(PHYSICAL REQUIREMENTS-Particles retained on 45 micron IS sieve)	-	1000	-
7.1-Table 2(iii)(PHYSICAL REQUIREMENTS-Average compressive strength)	-	3000	-
7.1-Table 2(iv)(PHYSICAL REQUIREMENTS-Compressive strength at 28 days)	-	3000	-
7.1-Table 2(v)(PHYSICAL REQUIREMENTS-Soundness by autoclave test )	-	1500	-

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(MATERIALS : ARMGURING)	-	3000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
16.5(Oxygen Index Test)	-	1000	-
16.1(Temperature Index)	-	1000	-
16.9(Test for Halogen Acid Gas Evolution)	-	1000	-

-
-

IS 303 (1989)

Plywood for General Purposes -

Grade BWR/Type AA/AB/BB

13000 View breakup
For BIS samples: BIS approved testing charges, for others: Rs.13000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	0	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	750	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	0	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	750	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	0	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	750	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	0	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	750	-
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	1500	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	3000	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	3000	-
11.3(Moisture Content - Part 1 of IS 1734)	-	1000	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	500	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	500	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	500	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	500	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	0	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	0	-
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	1000	-
5.1(Type - For BB Type)	-	0	-
5.1(Type - For AB Type)	-	0	-
5.1(Type - For AA Type)	-	0	-
4(Grade - For MR grade)	-	0	-
4(Grade - For BWR grade)	-	0	-

-
-

IS 2202 : Part 1 (1999)

Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

Grade-BWP /Type-BD,BN,PD,PN,MD,MN

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Plywood)	-	0	-
9.2(Workmanship & finish - IS 2202(Pt-1))	-	0	-
9.3(Workmanship & finish - IS 2202(Pt-1))	-	0	-
11.1(Height - IS 4020 (Pt-2))	-	500	-
11.1(Width- IS 4020 (Pt-2))	-	500	-
11.1(Thickness - IS 4020 (Pt-2))	-	500	-
11.1(Variation in thickness - IS 4020 (Pt-2))	-	0	-
11.1( Squareness Test - IS 4020 (Pt-2))	-	500	-
11.2( Twist, cupping & wrapping - IS 4020 (Pt-3))	-	1000	-
11.3(Depth of deviation - IS 4020(Pt-4))	-	1000	-
11.4(Impact Indentation Test - IS 4020(Pt-5))	-	1000	-
11.4(Depth of indentation - IS 4020(Pt-5))	-	0	-
11.5(Deflection at maximum load - IS 4020(Pt-6))	-	1000	-
11.5(Residual deflection - IS 4020(Pt-6))	-	0	-
11.6(Deflection of the edge at maximum load - IS 4020(Pt-7))	-	750	-
11.6(Residual deflection after removal of load - IS 4020(Pt-7))	-	0	-
11.6(Lateral buckling during loading - IS 4020(Pt-7))	-	750	-
11.6(Residual lateral buckling - IS 4020(Pt-7))	-	0	-
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	750	-
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	750	-
11.8(Buckling Test - IS 4020(Pt-9))	-	1500	-
11.8(Initial deflection - IS 4020(Pt-9))	-	0	-
11.8(Residual deformation after 15 minutes of unloading - IS 4020(Pt-9))	-	0	-
11.9(Slamming Test - IS 4020(Pt-10))	-	1000	-
11.1(Misuse Test - IS 4020(Pt-11))	-	1000	-
11.11(Varying Humidity Test - IS 4020(Pt-12))	-	1000	-
11.11(The recovery of the original size after subjecting the door to high and low humidity- IS 4020(Pt-12))	-	1000	-
11.11(Maximum departure from the general planeness - IS 4020(Pt-12))	-	1000	-
11.12(End Immersion Test - IS 4020(Pt-13))	-	1000	-
11.13(Knife Test - IS 4020(Pt-14))	-	1000	-
11.14(Glue Adhesion Test - IS 4020(Pt-15))	-	1000	-
11.15(Screw Withdrawal Resistance test - IS 4020 (Pt-16))	-	1000	-
11.15(Screw Withdrawal Strength - IS 4020 (Pt-16))	-	0	-

-
-

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

GRADE-BWP,MR/TYPE-DEC,COM

11000 View breakup
For BIS samples: BIS approved testing charges. For others: Rs.11000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.3(Dimensional Requirements - Length - 8.1.4)	-	1000	-
7.3(Dimensional Requirements - Width - 8.1.4)	-	0	-
7.3(Dimensional Requirements - Thickness - Annexure E)	-	0	-
7.3(Dimensional Requirements - Edge Straightness - Annexure D)	-	0	-
7.3(Dimensional Requirements - Squareness - Annexure D)	-	0	-
7.3(Dimensional Requirements - Variation in thickness - Annexure E)	-	0	-
8.1.3, 6.3.3, IS 303(Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-	1000	-
8.1.3, 6.3.3, IS 1328(Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Delamination - Annexure F)	-	1000	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-	0	-
9.2.1(Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-	0	-
9.2.1(Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-	0	-
9.2.1(Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-	0	-
9.2.1(Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-	0	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-	1000	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-	1000	-
9.2.3(Adhesion of Plies - Annexure H)	-	1000	-
9.2.4(Mycological Test [for MR grade only] - Annexure J)	-	2000	-
9.2.5(Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-	0	-
9.2.5(Modulus of rupture - AVERAGE - Annexure K)	-	1000	-
9.2.5(Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-	0	-
9.2.5(Modulus of elasticity - AVERAGE - Annexure K)	-	1000	-
9.2.6(Spot test - Annexure L)	-	2000	-

-
-

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

24000 View breakup
i) Size 8-12mm: Rs.8000/- All test + Rs.10000/- for Pullout Test ii) Size 16-28mm: Rs.9000/- All test + Rs.15000/- for Pullout Test iii) Size 32mm: Rs.10000/- All test + Rs.15000/- for Pullout Test. [Additional fee Rs.2000/- for micro element]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	1000	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	0	-
Cl 7.2(Weight)	-	1000	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1000	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	1000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	1000	-
Cl. 8.1 Table 3(TS/YS ratio)	-	0	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	1000	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	1000	-
Cl 5(Deformations and Surface Characteristics)	-	15000	-
4.1(Sulphur and phosphorous)	-	500	-
4.1(CE)	-	1000	-
4.1( Nitrogen%)	-	500	-
4.1(Ni)	-	500	-
4.1(Mo)	-	500	-
4.1(Cr)	-	500	-
4.1( Ti)	-	500	-
4.1(V)	-	500	-
4.1( Copper %)	-	500	-
4.1(Silicon %)	-	500	-
4.1(Sulphur %)	-	500	-
4.1(Phosphorus %)	-	500	-
4.1(Manganese %)	-	500	-
4.1(Carbon %)	-	500	-
4.1( Aluminium %)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-	500	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	500	-

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

20000 View breakup
For BIS samples: BIS approved testing charges-, Rs.20000/- for Single Core Cable & Rs.2000/- for each additional core

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.8(Smoke density rating)	-	3600	RUPEE 900 EXTRA FOR EACH OTHER CORE
10.6(Halogen evolution)	-	3600	RUPEE 900 EXTRA FOR EACH OTHER CORE
10.7(Temperature index)	-	3600	RUPEE 900 EXTRA FOR EACH OTHER CORE
10.5(Oxygen index)	-	3600	RUPEE 900 EXTRA FOR EACH OTHER CORE
11.1(Durability)	-	100	-
11(Identification)	-	100	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	2000	-
table 1 e) 3) (IR constant- max. Temp)	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
table 1 e) 3) (IR constant- Room temp )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
table 1 e) 3) (Volume Resistivity - Room temp )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
10.2(HV (room temperature))	-	1000	RUPEE 100 EXTRA FOR EACH OTHER CORE
10.1(HV (water immersion))	-	1500	RUPEE 150 EXTRA FOR EACH OTHER CORE
10.1(HV (water immersion))	-	1500	RUPEE 150 EXTRA FOR EACH OTHER CORE
10.4(Flammability test- Unaffected portion)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
10.4(Flammability test-Burning after flame removal)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1(Category Code)	-	100	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 4)(Cracks Observed)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	750	RUPEE 75 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	750	RUPEE 75 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 3)(Sheath- TS variation)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	375	RUPEE 37.5 EXTRA FOR EACH OTHER CORE
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	375	RUPEE 37.5 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 3)(Elongation variation)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 3)(TS variation)	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 3)(Elongation (After ageing))	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	250	RUPEE 25 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 1)(Elongation (Without ageing))	-	375	RUPEE 37.5 EXTRA FOR EACH OTHER CORE
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	375	RUPEE 37.5 EXTRA FOR EACH OTHER CORE
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	10	-
8.3(Thickness of Sheath)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
5.2(Application )	-	100	-
5.3(Thickness of Insulation)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
9.1(Ovality)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
9(Overall dimensions)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
4.2(Conductor resistance test)	-	1500	RUPEE 150 EXTRA FOR EACH OTHER CORE
4.1(Wrapping test (for Al))	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
4.1(Tensile test (for Al)- After Stranding)	-	1000	RUPEE 100 EXTRA FOR EACH OTHER CORE
4.1(Tensile test (for Al)-Before Stranding)	-	300	RUPEE 30 EXTRA FOR EACH OTHER CORE
4.1(Annealing test (for copper))	-	1000	RUPEE 100 EXTRA FOR EACH OTHER CORE
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	100	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	100	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	100	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	100	-
12(CONSTRUCTION Core Identification)	-	100	-
8.1(Sheath Material )	-	100	-
7(Binder Tape)	-	100	-
6.2(Filler)	-	100	-
5.1(Insulation)	-	100	-
4.4(Joints in Conductor)	-	100	-
4.4(Joints in Conductor)	-	100	-
4.1(Conductor - Material)	-	100	-
4.1(Conductor - Material)	-	100	-
10.11(Persulphate Test )	-	500	RUPEE 50 EXTRA FOR EACH OTHER CORE
12.0(Core identification)	-	100	-
4, IS 8130(Construction of conductor)	-	100	-
Table 2, IS 8130(No fo wire in a conductor)	-	100	-
8.3(Minimum thickness of Sheath)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
8.3(Avarage thickness of Sheath)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
5.3(Minimum thickness of insulation)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
5.3(Avarage thickness of insulation)	-	125	RUPEE 12.5 EXTRA FOR EACH OTHER CORE
Table 4(Copper purity test)	-	500	-
10.3(Spark test)	-	0	-
table 1, 4.2(insulation resistance test)	-	100	RUPEE 10 EXTRA FOR EACH OTHER CORE
5.4(Mechanical properties before and after ageing)	-	100	RUPEE 10 EXTRA FOR EACH OTHER CORE
10.11(Per sulphate test (for tinned Cu cable only))	-	100	RUPEE 10 EXTRA FOR EACH OTHER CORE

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

8292 View breakup
For BIS samples: Rs.8292/-, For others: Rs.10500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 15(Length, Width & Thickness)	-	1000	-
Cl 18(Weight)	-	1000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	1000	-
Cl 11.3(Press)	-	1000	-
Cl 7(Workmanship)	-	1000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	1000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	1000	-
Cl 12(Sudden Load Applied)	-	5000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	500	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	1000	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	500	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	500	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	500	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	500	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	500	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	500	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	500	-

-
Except for grade E 250 C material of thickness above 12mm

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

33,43,53,43S,53S

10000 View breakup
Rs.10000/- [Rs.6000/- for physical, Rs.4000/- for chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	0	-
7 Table-3 iii a(Setting Time Initial)	-	500	-
7 Table-3 iii b(Setting Time Final)	-	500	-
7 Table-3 i.(Fineness)	-	1000	-
7 Table-3 ii a(Expansion by Le Chatelier)	-	500	-
7 Table-3 ii a(Expansion after aeration)	-	0	-
7 Table-3 ii b(Expansion by Autoclave)	-	1000	-
7 Table-3 ii b(Expansion after aeration)	-	0	-
6.1 Table-2 viii(Alkali content)	-	1000	-
6.1 Table-2 vii(Chloride content)	-	1000	-
6.1 Table-2 vi(Loss on ignition)	-	1000	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	1000	-
6.1 Table-2 iv(Magnesia)	-	1000	-
6.1 Table-2 iii.(Insoluble residue)	-	1000	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	2000	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	3000	-
6 - Table - 1 viii(Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	2000	-
6 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	3000	-
6.1 Table-2 viii(Alkali content)	-	1000	-
6.1 Table-2 vii(Chloride content)	-	1000	-
6.1 Table-2 vi(Loss on ignition)	-	1000	-
6.1 Table-2 v(Total Sulphur Content calculated as Sulphuric Anhydride)	-	1000	-
6.1 Table-2 iv(Magnesia)	-	1000	-
6.1 Table-2 iii.(Insoluble residue)	-	1000	-
6.1 Table-2 ii.(Ratio of percentage of alumina to that of iron oxide)	-	2000	-
6.1 Table-2 i.(Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	-	3000	-
6 - Table - 1 viii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vii(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Loss on ignition - Cl 4.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Magnesia - Cl 4.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Insoluble residue - Cl 4.10 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Ratio of percentage of alumina to that of iron oxide - Cl 4 of IS 4032:1985)	-	2000	-
6 - Table - 1 i(Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-	3000	-

-
-

IS 455 (2015)

Portland slag cement - Specification

PSC

10000 View breakup
Rs.10000/- [Rs.6000/- for physical, Rs.4000/- for chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7 Table-2(Cl. 7 Table-2 i (Fineness ))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 ii a (Soundness , Le Chatelier Expansion ))	-	500	-
Cl. 7 Table-2(Cl. 7 Table-2 ii a (Expansion after aeration ))	-	0	-
Cl. 7 Table-2(Cl. 7 Table-2 ii b (Soundness , Autoclave Expansion ))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 ii b (Expansion after aeration ))	-	0	-
Cl. 7 Table-2(Cl. 7 Table-2 iii a (Setting time Initial))	-	500	-
Cl. 7 Table-2(Cl. 7 Table-2 iii b (Setting time Final))	-	500	-
Cl. 7 Table-2(Cl. 7 Table-2 iv a (Compressive Strength 72±1 hr IS))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 iv b (Compressive Strength 168±2 hr ))	-	1000	-
Cl. 7 Table-2(Cl. 7 Table-2 iv c (Compressive Strength 672±4 hr) )	-	1000	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	1000	-
6 - Table - 1 vii( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Loss on ignition - Cl 6.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Sulphide sulphur (S) - Cl 6.12 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 6.8 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 6.9 of IS 4032:1985)	-	1000	-

-
-

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

PPC(FAB)

11000 View breakup
Rs.11000/- [ For mechanical-Rs.7000/-for chemical Rs.4000/- ]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	-
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	500	-
7 -Table 2- ii- a(Expansion after aeration - 4031 Part 3)	-	0	-
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	1000	-
7 -Table 2- ii- b(Expansion after aeration- 4031 Part 3)	-	0	-
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	-
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	-
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	1000	-
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	1000	-
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1000	-
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1000	-
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	-
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	-
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	-

-
Lab is recognized revised version of standard IS 1489(Pt-1) :2015.

IS 1475 : Part 1 (2001)

Self - Contained drinking water coolers - Specification: Part 1 energy consumption and performance (Third Revision)

30000 View breakup
Rs.15000/-( for one water cooler), Rs.30000/- ( for two water cooler0

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.2(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.3(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.4(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.5(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.6(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.7(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.8(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.9(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.1(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.11(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.12(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.13(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.14(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.15(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.16(COMPONENTS AND THEIR MATERIALS)	-	500	-
6.17(COMPONENTS AND THEIR MATERIALS)	-	500	-
7.7.1(Insulation Resistance)	-	3000	-
7.7.2(High Voltage Test)	-	3000	-
7.7.3(Cooling capacity rating test)	-	4000	-
7.7.4(Maximum operating conditions)	-	10000	-
7.8.2(Performance test)	-	1500	-

-
upto 250 liters

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

Type - Powder form/ Liquid form

10000 View breakup
Rs.9000/- [ Rs.8000/-for Mechanical, Rs.1000/- for Chemical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	3000	-
Cl 3.2(Initial & Final)	-	500	-
Cl 3.2(Initial & Final)	-	500	-
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	2000	-
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	2000	-
Clause 3.4(Chloride content)	-	1000	-
Clause 3.4(Chloride content)	-	1000	-

-
-

IS 814 (2004)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

14500 View breakup
i) Grade EA, EC, ER, ERRXXXX-: Rs.14500/-(Single size), Rs.29000/- (Two size), Rs..36500/-(For three size), Rs.40000/- (Four size), , For physical Rs.11000/-, Radiography test Rs.1000/-, For chemical Rs.2500/- ii) for EB XXXXHJX grade per size Full test (EB XXXX grade): Rs.18000/-(for two size Rs.36000/- three size Rs.44500/- four size Rs.50000/-) , Diffusible hydrogen test-Rs.5000/-, Bend test-Rs.8000/-, Running performance test-Rs.2000/-, Increase mental recover test-Rs.3000/- , For physical Rs.13000/-, Radiography test-:Rs.1000/-, For chemical Rs.4000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 & 8.2(Carbon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	carbon content
6 & 8.2(Silicon- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Silicon content
6 & 8.2(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Phosphorus content
6 & 8.2(Manganese- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Manganese content
6 & 8.2(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	Sulphur content
7.1.1(Diameter of Core Wire)	-	500	Dimension
7.1.2(Length of Electrodes)	-	500	Dimension
7.2.1(Contact End)	-	500	Dimension
7.2.2(Arc striking End)	-	500	Dimension
7.3(Concentricity of Flux covering with core wire)	-	500	Dimension
7.4(Defects of Core wire and Coverings)	-	500	Dimension
9.1.2 Table 6 (Ultimate Tensile Strength-Annex F)	-	3000	Strength Parameter
9.1.2 Table 6 ( Yield Stress -Annex F)	-	1000	Strength Parameter
9.1.2 Table 6 (Percentage Elongation on Gauge Length-Annex F)	-	1000	Strength Parameter
9.1.3 Table 6 ( Impact Strength-Annex F)	-	3000	Strength Parameter
9.2(Butt Weld Bend Test-IS 1599)	-	3000	Strength Parameter
9.6(Radiographic Test- IS 1182)	-	1000	NDT Test
9.3(Running PerformanceTest-Annex H)	-	2000	Running Performance Test
9.4(Increased Metal Recovery Test-IS 13043)	-	3000	Increased Metal Recovery Test
9.5(Diffusible Hydrogen Evaluation Test-IS 11802)	-	5000	Diffusible Hydrogen Evaluation Test
6 & 8.2(Copper- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Vanadium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Titanium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Alumiminium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Cr+Ni+Mo - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	1000	-
6 & 8.2(Chromium- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Nickel- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Molybdenum- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
6 & 8.2(Mn+Ni+Cr+Mo+V - Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	2000	-

-
-

IS 3097 (2006)

Veneered Particle Boards -Specification

- View breakup
Rs.11000/- [ Rs.11000/-for Mechanical]

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

-
-

IS 15652 (2006)

Insulating mats for electrical purposes - Specification

Insulating Mats for Electrical Purposes

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	0	-
10.a)(Packing)	-	0	-
10.b)(Packing)	-	0	-
10.c)(Packing)	-	0	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	0	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	0	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	0	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	0	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	500	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	0	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	0	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	1500	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	4000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4500	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	4000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	2500	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	7000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	3000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Thermal Properties (Cl..8.4))	-	4000	-
8(Extreme Low Temperature (Cl.8.6))	-	6000	-

-
-

Bureau of Indian Standards

The National Standards Body of India

National Test House (NR) - NTH, Ghaziabad

Kamla Nehru Nagar,Ghaziabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

9999472699 director-gzb@nth.gov.in

Scope List

No Record Found