BIS - LIMS (Laboratory Information Management System)

Samridhi Test House Pvt. Ltd.

KH.NO. 45/23/1 GROUND FLOOR, VILLAGE & POST OFFICE VILLAGE PRAHALADPUR, North Delhi, NEW DELHI, North West, Delhi, 110042

9870394724 info@samridhitesthouse.com

Scope List

Reset

101 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 9754 (2025)

HIGH DENSITY POLYETHYLENE CONTAINERS FOR PACKING OF LIQUID PESTICIDES (UP TO 1 LITRE CAPACITY) - SPECIFICATION (first revision)

32000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Melt Flow Rate (MFR))	-	1100	-
4.1.1(Density)	-	1100	-
4.1.2(Material Identification of Plug)	-	1000	-
4.1.2(Material Identification of Caps/Closure)	-	3000	-
4.2(Ullage & Nominal Capacity)	-	100	-
4.2.2(Mass of Container)	-	500	-
4.3(Wall thickness at any point of Container)	-	500	-
4.4(Construction of Container)	-	500	-
4.4.1(Container Height to Neck Face)	-	500	-
4.4.2(Container Overall Height)	-	500	-
4.4.3(Container Diameter)	-	500	-
4.4.4(Neck Height)	-	500	-
4.4.5(Neck Diameter)	-	600	-
4.4.5(Neck Thread diameter)	-	500	-
4.4.6(Neck Bore)	-	500	-
4.4.7(Neck Ovality)	-	500	-
4.5(Construction of Closure and Sealing)	-	500	-
4.6(Workmanship and Finish)	-	500	-
5.1.1(Leakage Test Vertically Downwards)	-	2000	-
5.1.1(Leakage Test Vertically Upwards)	-	2700	-
5.2(Stress Crack Resistance Test for 360 hours)	-	11000	-
5.3(Drop Test @ Ambient Temperature)	-	1900	-
5.3(Drop Test @ 0 Deg.C)	-	1900	-
5.4(Ink Adhesion test)	-	1500	-
7(Marking & BIS Cert. Marking)	-	500	-
4.1.1(Melt Flow Rate (MFR))	-	0	-
4.1.1(Density)	-	0	-
4.1.2(Material Identification of Plug)	-	0	-
4.1.2(Material Identification of Caps/Closure)	-	0	-
4.2(Ullage & Nominal Capacity)	-	0	-
4.2.2(Mass of Container)	-	0	-
4.3(Wall thickness at any point of Container)	-	0	-
4.4(Construction of Container)	-	0	-
4.4.1(Container Height to Neck Face)	-	0	-
4.4.2(Container Overall Height)	-	0	-
4.4.3(Container Diameter)	-	0	-
4.4.4(Neck Height)	-	0	-
4.4.5(Neck Diameter)	-	0	-
4.4.5(Neck Thread diameter)	-	0	-
4.4.6(Neck Bore)	-	0	-
4.4.7(Neck Ovality)	-	0	-
4.5(Construction of Closure and Sealing)	-	0	-
4.6(Workmanship and Finish)	-	0	-
5.1.1(Leakage Test Vertically Downwards)	-	0	-
5.1.1(Leakage Test Vertically Upwards)	-	0	-
5.2(Stress Crack Resistance Test for 360 hours)	-	0	-
5.3(Drop Test @ Ambient Temperature)	-	0	-
5.3(Drop Test @ 0 Deg.C)	-	0	-
5.4(Ink Adhesion test)	-	0	-
7(Marking & BIS Cert. Marking)	-	0	-

-
Included w.e.f. 19.12.2025

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

All Grade / Type / Size / Designation etc.

9400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	100	-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	300	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	100	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	300	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	300	-
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	100	-
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	100	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	100	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	100	-
6.2.2(Fittings)	-	100	-
6.3(General)	-	100	-
6.3(General)	-	100	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	300	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	300	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	300	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	100	-
8.2.2(Regulated Emitting Pipes)	-	200	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	100	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	100	-
8.3.3(Flow Paths in Emitting Unit)	-	100	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	200	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	300	-
8.5(Resistance to Tension at Elevated Temperature)	-	300	-
8.5(Resistance to Tension at Elevated Temperature)	-	100	-
8.5(Resistance to Tension at Elevated Temperature)	-	100	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	100	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	200	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	200	-
8.8(Determination of Emitting Unit Exponent)	-	200	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	100	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	100	-
4.1 a(Identification)	-	200	-
4.1 a(Identification)	-	200	-
4.1 c(Volatile matter Extract)	-	200	-
4.1 d(Density)	-	100	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	100	-
4.2(Carbon black dispersion)	-	300	-
5.1(Materials)	-	100	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	100	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	100	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	100	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	100	-
6.2(Fittings)	-	100	-
6.3(General)	-	100	-
7.1(Test Specimens)	-	100	-
7.2(Order of Tests)	-	200	-
7.3(Testing Conditions)	-	100	-
7.4(Accuracy of Measuring Devices)	-	100	-
8.1(Uniformity of Emission Rate)	-	100	-
8.1.2(Unregulated Emitting Pipes)	-	100	-
8.1.3(Regulated Emitting Pipes)	-	100	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	100	-
8.2.1(Unregulated Emitting Pipes)	-	100	-
8.2.2(Regulated Emitting Pipes)	-	100	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	100	-
8.3.3(Flow Paths in Emitting Unit)	-	100	-
8.3.4(Spacing of Emitter Units)	-	100	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	100	-
8.5(Resistance to Tension at Elevated Temperature)	-	100	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	100	-
8.7.1(Acceptance Test)	-	100	-
8.7.2(Type Test)	-	100	-
8.8(Determination of Emitting Unit Exponen)	-	100	-
9.1(Non-regulated Emitting Pipe)	-	100	-
9.2(Regulated Emitting Pipe)	-	100	-
10.1(Marking)	-	100	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	100	-
4.2(Carbon black content)	-	100	-
8.3.4(Spacing ofEmitter Units)	-	100	-
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	0	-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	0	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	0	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	0	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	0	-
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	0	-
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	0	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	0	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0	-
6.2.2(Fittings)	-	0	-
6.3(General)	-	0	-
6.3(General)	-	0	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	0	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	0	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	0	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	0	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	0	-
8.8(Determination of Emitting Unit Exponent)	-	0	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	-
4.1 a(Identification)	-	0	-
4.1 a(Identification)	-	0	-
4.1 c(Volatile matter Extract)	-	0	-
4.1 d(Density)	-	0	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	0	-
4.2(Carbon black dispersion)	-	0	-
5.1(Materials)	-	0	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	0	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	0	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	0	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	0	-
6.2(Fittings)	-	0	-
6.3(General)	-	0	-
7.1(Test Specimens)	-	0	-
7.2(Order of Tests)	-	0	-
7.3(Testing Conditions)	-	0	-
7.4(Accuracy of Measuring Devices)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.2(Unregulated Emitting Pipes)	-	0	-
8.1.3(Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregulated Emitting Pipes)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.3.4(Spacing of Emitter Units)	-	0	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	0	-
8.7.1(Acceptance Test)	-	0	-
8.7.2(Type Test)	-	0	-
8.8(Determination of Emitting Unit Exponen)	-	0	-
9.1(Non-regulated Emitting Pipe)	-	0	-
9.2(Regulated Emitting Pipe)	-	0	-
10.1(Marking)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
4.2(Carbon black content)	-	0	-
8.3.4(Spacing ofEmitter Units)	-	0	-

-
Included w.e.f 12.11.2025

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

Household and Similar Electrical Appliances

44500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	1000	-
6(Classification- IS 302-1)	-	500	-
5(General conditions for the tests)	-	500	-
19.11.4.7(Harmonics)	-	0	EMI/EMC test facility not available
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	EMI/EMC test facility not available
19.11.4.5(Immunity to conducted discharges)	-	0	EMI/EMC test facility not available
19.11.4.4(Surge immunity test)	-	0	EMI/EMC test facility not available
19.11.4.3(Fast transient bursts)	-	0	EMI/EMC test facility not available
19.11.4.2(Radiated fields)	-	0	EMI/EMC test facility not available
19.11.4.1(Electrostatic discharges)	-	0	EMI/EMC test facility not available
11.8(Temperature rise)	-	5000	-
11.7(Duration corresponding)	-	2500	-
11.6(Combined appliances)	-	2500	-
11.5(Motor-operated appliances)	-	2500	-
11.4(Heating appliances)	-	2500	-
8.1.5(Live parts of built-in appliances)	-	2500	-
18(Endurance)	-	1000	-
17(Overload protection of transformers and associated circuits)	-	2000	-
16(Leakage current and electric strength)	-	1000	-
4(General requirement)	-	500	-
32.1(Radiation Toxicity and Similar Hazards)	-	1000	-
31(Resistance to Rusting)	-	1000	-
30.2(Needle Flame Test)	-	1000	-
30.2(Glow Wire Test)	-	1000	-
30.1(Ball pressure test)	-	1000	-
29(clearance, creepage distances and solid insulation)	-	2000	-
28(Screw test and connections)	-	1000	-
27.1(Provision for Earthing, IS 302-1)	-	2000	-
26(Terminals for external conductors)	-	1000	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	1000	-
24(Components)	-	3000	-
23.1(Internal Wiring, IS 302-1)	-	1000	-
22.1(Construction, IS 302-1)	-	5000	-
21.1(Mechanical Strength, IS 302-1)	-	2000	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	1000	-
19(Abnormal Operation)	-	2000	-
18(Endurance)	-	0	-
17(Over Load Protection of Transformers and associated circuits)	-	0	-
16.3(Electric Strength (after clause 15 and 16.2))	-	1000	-
16.2(Leakage Current (after Clause 15))	-	1000	-
16.1(General)	-	1000	-
16.0(General)	-	3000	-
15.3(Humidity Test)	-	1000	-
15.2(Spillage Test)	-	1000	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	4900	-
15.0(Moisture resistance)	-	5000	-
14(Transient Over Voltages)	-	1000	-
13.3(Electric Strength at operating temperature)	-	1000	-
13.2(Leakage current at operating temperature)	-	1000	-
13(Leakage current and electric strength at operating temperature)	-	1000	-
11.3(Heating)	-	1000	-
11.2(General)	-	500	-
11.1(General)	-	500	-
10.2(Current input)	-	1000	-
10.1(Power input)	-	1000	-
9(Starting of motor operation test requirements and tests)	-	1000	-
8.1.4(Protection against live parts against protective impedance)	-	1000	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	1000	-
8.1.2(Protection against live parts in openings)	-	1000	-
8.1.1(Protection against live parts in all positions)	-	1000	-
7(Marking and instructions)	-	500	-
A.2(Earth continuity test)	-	1000	-
Annex C(Ageing test on motors)	-	1000	-
Annex D(Thermal motor protectors)	-	1000	-
15.2(Moisture resistance)	-	1000	-
19.17(Abnormal Operation, IS 302-1)	-	1000	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	1000	-
21.2(Mechanical Strength, IS 302-1)	-	1000	-
21.3(Mechanical Strength, IS 302-1)	-	1000	-
22.5(Construction)	-	0	EMI/EMC test facility not available.
22.6(Construction, IS 302-1)	-	1000	-
22.11(Construction, IS 302-1)	-	1000	-
22.16(Construction)	-	1000	-
22.32(Construction, IS 302-1)	-	0	Oxygen Bomb with Pressure Gauge not available
22.42(Construction)	-	1000	-
23.3(Internal Wiring, IS 302-1)	-	1000	-
25.6(Supply connection and external flexible cords, IS 302-1)	-	5000	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
26.5(Terminals for external conductors)	-	1000	-
27.5(Provision for Earthing, IS 302-1)	-	1000	-
28.1(Screws and connections)	-	1000	-
22.2(Construction, IS 302-1)	-	1000	-
22.3(Construction, IS 302-1)	-	1000	-
B.22.4(Construction, IS 302-1)	-	1000	-
B.22.5(Construction, IS 302-1)	-	1000	-

-
"Domestic Electric Clothes Washing Machines (For testing charges please refer part 2 standard in LIMS)"

IS 15652 (2006)

Insulating mats for electrical purposes - Specification

All Grade / Type / Size / Designation etc.

49000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	900	-
10.a)(Packing)	-	900	-
10.b)(Packing)	-	900	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	900	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	900	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1900	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1900	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1900	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1900	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1900	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	900	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	900	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	4900	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	4900	-
8(Thermal Properties (Cl..8.4))	-	4900	-
8(Thermal Properties (Cl..8.4))	-	4900	-
8(Extreme Low Temperature (Cl.8.6))	-	4900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	900	-
10(Packing)	-	900	-
10(Packing)	-	900	-
10(Packing)	-	900	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	900	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	900	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	900	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	900	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1900	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1900	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1900	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1900	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1900	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	900	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	1900	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	4900	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	4900	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	4900	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	4900	-
8(Thermal Properties (Cl..8.4))	-	4900	-
8(Thermal Properties (Cl..8.4))	-	4900	-
8(Extreme Low Temperature (Cl.8.6))	-	4900	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	900	-
10.c)(Packing)	-	900	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	900	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	4900	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	4900	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	900	-

-
Included w.e.f 14.10.2025

IS 9873 : Part 3 (2020)

Safety of Toys Part 3 Migration of Certain Elements ( Third Revision )

All Grade / Type / Size / Designation

1900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	200	-
4.1(Sample preparation as per clause 8 of IS 9873 Part 3:1999)	-	200	-
Cl-4.1 & 4.2,Table 1,sl.no-i(Sb)	-	200	-
Cl-4.1 & 4.2,Table 1,sl.no-ii(As)	-	200	-
Cl-4.1 & 4.2,Table 1,sl.no-iii(Ba)	-	200	-
Cl-4.1 & 4.2,Table 1,sl.no-iv(Cd)	-	200	-
Cl-4.1 & 4.2,Table 1,sl.no-v(Cr)	-	200	-
Cl-4.1 & 4.2,Table 1,sl.no-vi(Pb)	-	200	-
Cl-4.1 & 4.2,Table 1,sl.no-vii(Hg)	-	200	-
Cl-4.1 & 4.2,Table 1,sl.no-viii(Se)	-	200	-

-
Included w.e.f 29.10.2025

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

All Grade / Type / Size / Designation

12800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2800	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	1500	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	1000	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	1000	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	1000	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	1000	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	500	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	500	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	1000	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	2800	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	0	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	0	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	0	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	0	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	0	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	0	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	0	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	0	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	0	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	0	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	0	-

-
Included w.e.f 26.11.2025 Cl.6 Material (Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)

IS 17077 : Part 1 (2022)

PLASTICS ACRYLONITRILE- BUTADIENESTYRENE ABS MOULDING AND EXTRUSION MATERIALS PART 1 DESIGNATION SYSTEM AND SPECIFICATIONS

All Grade / Type / Size / Designation

7800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.5.1 and 6.1(Vicat Softening temperature,(°C),Clause 5 Table 3, IS 17077 (P-2))	-	1100	-
4.2.5.2 and 6.2(Charpy Notched Impact Strength,(kj/m²),Clause 5 Table 3, IS 17077 (P-2))	-	1700	-
4.2.5.3 and 6.3(Melt Mass Flow Rate,(g/10min),Clause 5 Table 3,IS 17077 (P-2))	-	1000	-
4.2.5.4 and 6.4(Tensile Modulus,(Mpa),Clause 5 Table 3,IS 17077 (P-2))	-	1700	-
6.5.1.1(Pigments and colourants, IS 9833)	-	0	-
6.5.1.2(Overall migration,(mg/dm²), IS 9845)	-	2100	-
4.2.5.1 and 6.1(Vicat Softening temperature,(°C),Clause 5 Table 3, IS 17077 (P-2))	-	0	-
4.2.5.2 and 6.2(Charpy Notched Impact Strength,(kj/m²),Clause 5 Table 3, IS 17077 (P-2))	-	0	-
4.2.5.3 and 6.3(Melt Mass Flow Rate,(g/10min),Clause 5 Table 3,IS 17077 (P-2))	-	0	-
4.2.5.4 and 6.4(Tensile Modulus,(Mpa),Clause 5 Table 3,IS 17077 (P-2))	-	0	-
6.5.1.1(Pigments and colourants, IS 9833)	-	0	-
6.5.1.2(Overall migration,(mg/dm²), IS 9845)	-	0	-
4.2.5.1 and 6.1(Vicat Softening temperature,(°C),Clause 5 Table 3, IS 17077 (P-2))	-	0	-
4.2.5.2 and 6.2(Charpy Notched Impact Strength,(kj/m²),Clause 5 Table 3, IS 17077 (P-2))	-	0	-
4.2.5.3 and 6.3(Melt Mass Flow Rate,(g/10min),Clause 5 Table 3,IS 17077 (P-2))	-	0	-
4.2.5.4 and 6.4(Tensile Modulus,(Mpa),Clause 5 Table 3,IS 17077 (P-2))	-	0	-
6.5.1.1(Pigments and colourants, IS 9833)	-	0	-
6.5.1.2(Overall migration,(mg/dm²), IS 9845)	-	0	-

-
Included w.e.f 12.11.2025 Exclusion: 6.5.1.1 (Pigments and colourants, IS 9833) Pigments and Colourants HPLC not Available

IS 2267 : Part 1 (2024)

Polystyrene (ps) moulding and extrusion materials : Part 1 designation system and basis for specification (Third Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.3(Data block 2, Material)	-	1000	-
Cl-4.4(Data block 3)	-	1000	-
Cl-4.5.2(Vicat softening temperature)	-	10000	-
Cl-4.5.3(Melt mass-flow rate)	-	7000	-
Cl-4.2(Data block 1)	-	1000	-
Cl-4.3(Data block 2, Material)	-	0	-
Cl-4.4(Data block 3)	-	0	-
Cl-4.5.2(Vicat softening temperature)	-	0	-
Cl-4.5.3(Melt mass-flow rate)	-	0	-
Cl-4.2(Data block 1)	-	0	-

-
Included w.e.f. 04.11.2025

IS 13960 (1994)

Thermoplastic strappings - Specification

All Grade / Type / Size / Designation

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Types)	-	14000	-
5(Manufacture)	-	0	-
6(Workmanship, Finish and Appearance)	-	500	-
7(Requirements)	-	5000	-
8(Packing and Marking)	-	500	-
4(Types)	-	0	Repeated Test Parameter
5(Manufacture)	-	0	Repeated Test Parameter
6(Workmanship, Finish and Appearance)	-	0	Repeated Test Parameter
7(Requirements)	-	0	Repeated Test Parameter
8(Packing and Marking)	-	0	Repeated Test Parameter

-
Included w.e.f.09.10.2025

IS 15559 (2004)

Polyester strapping - Specification

All Grade / Type / Size / Designation

5300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Manufacture)	-	500	-
4.1(Manufacture)	-	500	-
4.2(Surface finish)	-	250	-
4.3(Colour)	-	250	-
4.4(Intrinsic Viscosity)	-	700	-
4.5(Freedom from Defects)	-	200	-
4.6, Table-1(Dimensions and Physical Properties)	-	300	-
4.7(Tolerance on Width and Thickness)	-	300	-
5.1, Table-2(Tensile Strength and Elongation)	-	300	-
5.2(Split Resistance)	-	450	-
5.3, Table-3(Camber)	-	250	-
Table-1 (2)(Nominal width of strapping)	-	200	-
Table-1 (3)(Nominal thickness of strapping)	-	200	-
Table-1 (4)(Type)	-	100	-
Table-1 (5)(Breaking strength, Min)	-	200	-
Table-2 (2)(Tensile strength, kg/mm2)	-	200	-
Table-2 (3)(Elongation, %)	-	300	-
Table-2 (4)(Type)	-	200	-
Table-3 (2)(Camber- Nominal width (mm))	-	200	-
Table-3 (3)(Camber, Max (mm))	-	200	-
4.1(Manufacture)	-	0	-
4.1(Manufacture)	-	0	-
4.2(Surface finish)	-	0	-
4.3(Colour)	-	0	-
4.4(Intrinsic Viscosity)	-	0	-
4.5(Freedom from Defects)	-	0	-
4.6, Table-1(Dimensions and Physical Properties)	-	0	-
4.7(Tolerance on Width and Thickness)	-	0	-
5.1, Table-2(Tensile Strength and Elongation)	-	0	-
5.2(Split Resistance)	-	0	-
5.3, Table-3(Camber)	-	0	-
Table-1 (2)(Nominal width of strapping)	-	0	-
Table-1 (3)(Nominal thickness of strapping)	-	0	-
Table-1 (4)(Type)	-	0	-
Table-1 (5)(Breaking strength, Min)	-	0	-
Table-1 (5)(Breaking strength, Min)	-	0	-
Table-2 (2)(Tensile strength, kg/mm2)	-	0	-
Table-2 (2)(Tensile strength, kg/mm2)	-	0	-
Table-2 (3)(Elongation, %)	-	0	-
Table-2 (3)(Elongation, %)	-	0	-
Table-2 (4)(Type)	-	0	-
Table-2 (4)(Type)	-	0	-
Table-3 (2)(Camber- Nominal width (mm))	-	0	-
Table-3 (2)(Camber- Nominal width (mm))	-	0	-
Table-3 (3)(Camber, Max (mm))	-	0	-

-
Included w.e.f 14.10.2025

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

All

62000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4( Designation)	-	200	-
Cl 7(Dimensions Of Pipes)	-	500	-
Cl 8(Visual Appearance)	-	300	-
Cl 9.1(Hydraulic Characteristics)	-	4500	-
Cl 9.2(Fusion Compatibility)	-	3000	-
Cl 9.3(Reversion Test )	-	650	-
Cl 9.4 & Annex B(Impact Strength)	-	900	-
Cl 9.5(Density)	-	500	-
Cl 9.6(Melt Flow Rate)	-	1000	-
Cl 9.7(Carbon Black Content & Dispersion)	-	1500	-
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	40000	-
Cl 9.9(Opacity)	-	600	-
5(Colour)	-	250	-

-
Included w.e.f 11.09.2025

IS 3315 (2024)

Direct Evaporative Air Cooler â Specification (Fourth Revision)

39500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Enclosure)	-	200	-
Cl-5.2(Filter Pads)	-	100	-
Cl-5.3(Sump Tank Capacities)	-	1500	-
Cl-5.4(Blower/Fan)	-	500	-
Cl-5.4.3(Fan motor)	-	1500	-
Cl-5.5(Pump Set)	-	1500	-
Cl-5.6.1(Electrical wiring and connection)	-	500	-
Cl-5.6.2(Suitable power cable)	-	900	-
Cl-5.7(Switches)	-	1900	-
Cl-6(Rating Requirement)	-	1900	-
Cl-8.1(Performance Requirement)	-	1900	-
Cl-8.2(Sound Test)	-	1500	-
Cl-8.3(Air Delivery (Air Flow) Test)	-	1500	-
Cl-8.4(Cooling Efficiency Test)	-	3900	-
Cl-8.5(Power Consumption)	-	1900	-
Cl-8.6(EER Calculation Method)	-	900	-
Cl-8.7(Drop Test)	-	1900	-
Cl-8.8(Air Cooler Blower/Fan Reliability Test)	-	1500	-
Cl-12.2.1(General Running Tests)	-	2000	-
Cl-12.2.2(Protection against Electric Shock)	-	900	-
Cl-12.2.3(High Voltage Tests)	-	1900	-
Cl-12.2.4(Leakage Current)	-	900	-
Cl-12.2.5(Provision for Earthing)	-	900	-
Cl-12.2.6(Finish)	-	900	-
Cl-13(Additional Requirement for ECO-Mark)	-	1900	-
Cl-14(Storage)	-	3900	-
Cl-5.1(Enclosure)	-	0	-
Cl-5.2(Filter Pads)	-	0	-
Cl-5.3(Sump Tank Capacities)	-	0	-
Cl-5.4(Blower/Fan)	-	0	-
Cl-5.4.3(Fan motor)	-	0	-
Cl-5.5(Pump Set)	-	0	-
Cl-5.6.1(Electrical wiring and connection)	-	0	-
Cl-5.6.2(Suitable power cable)	-	0	-
Cl-5.7(Switches)	-	0	-
Cl-6(Rating Requirement)	-	0	-
Cl-8.1(Performance Requirement)	-	0	-
Cl-8.2(Sound Test)	-	0	-
Cl-8.3(Air Delivery (Air Flow) Test)	-	0	-
Cl-8.4(Cooling Efficiency Test)	-	0	-
Cl-8.5(Power Consumption)	-	0	-
Cl-8.6(EER Calculation Method)	-	0	-
Cl-8.7(Drop Test)	-	0	-
Cl-8.8(Air Cooler Blower/Fan Reliability Test)	-	0	-
Cl-12.2.1(General Running Tests)	-	0	-
Cl-12.2.2(Protection against Electric Shock)	-	0	-
Cl-12.2.3(High Voltage Tests)	-	0	-
Cl-12.2.4(Leakage Current)	-	0	-
Cl-12.2.5(Provision for Earthing)	-	0	-
Cl-12.2.6(Finish)	-	0	-
Cl-13(Additional Requirement for ECO-Mark)	-	0	-
Cl-14(Storage)	-	0	-

-
Included w.e.f 11.09.2025

IS 15225 (2002)

Chlorinated polyvinyl chloride compounds used for pipes and fittings - Specifications

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Designation)	-	500	-
4.2.1(Data block 1)	-	500	-
4.2.2(Data block 2)	-	500	-
4.2.3, Table1(Data block 3)	-	500	-
4.2.4, table 2(Data block 4)	-	500	-
4.2.5, table 3(Data block 5)	-	500	-
4.2.6(Data block 6)	-	500	-
8.1.1(Resin k-value)	-	1000	-
8.1.2(Resin chlorine content)	-	4000	-
8.1.3(Form)	-	200	-
8.1.4(Compound chlorine content)	-	4000	-
8.1.5(Appearance)	-	200	-
8.2.1(Vicat softening temperature)	-	1700	-
8.2.2(Charpy impact strength)	-	1700	-
8.2.3(Tensile strength)	-	1700	-
8.2.4(Tensile modulus)	-	1700	-
8.3(Ash content)	-	900	-
4(Designation)	-	0	-
4.2.1(Data block 1)	-	0	-
4.2.2(Data block 2)	-	0	-
4.2.3, Table1(Data block 3)	-	0	-
4.2.4, table 2(Data block 4)	-	0	-
4.2.5, table 3(Data block 5)	-	0	-
4.2.6(Data block 6)	-	0	-
8.1.1(Resin k-value)	-	0	-
8.1.2(Resin chlorine content)	-	0	-
8.1.3(Form)	-	0	-
8.1.4(Compound chlorine content)	-	0	-
8.1.5(Appearance)	-	0	-
8.2.1(Vicat softening temperature)	-	0	-
8.2.2(Charpy impact strength)	-	0	-
8.2.3(Tensile strength)	-	0	-
8.2.4(Tensile modulus)	-	0	-
8.3(Ash content)	-	0	-
4(Designation)	-	0	-
4.2.1(Data block 1)	-	0	-
4.2.2(Data block 2)	-	0	-
4.2.3, Table1(Data block 3)	-	0	-
4.2.4, table 2(Data block 4)	-	0	-
4.2.5, table 3(Data block 5)	-	0	-
4.2.6(Data block 6)	-	0	-
8.1.1(Resin k-value)	-	0	-
8.1.2(Resin chlorine content)	-	0	-
8.1.3(Form)	-	0	-
8.1.4(Compound chlorine content)	-	0	-
8.1.5(Appearance)	-	0	-
8.2.1(Vicat softening temperature)	-	0	-
8.2.2(Charpy impact strength)	-	0	-
8.2.3(Tensile strength)	-	0	-
8.2.4(Tensile modulus)	-	0	-
8.3(Ash content)	-	0	-

-
Included w.e.f. 14.08.2025

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

280000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Grade of material)	-	200	-
4.3(Nominal Diameter)	-	100	-
4.4(Colour)	-	100	-
5.1(Polyethylene compound)	-	500	-
5.3(Anti-oxidant)	-	0	Anti-oxidant test facility not available
5.4(U-V stabilizer)	-	0	U-V Stablizer test facility not available
5.7(PE Compound Quality Evaluation)	-	205000	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	1000	-
5.6(Resistance to Weathering)	-	8000	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	100	-
6.1(Out of Roundness (Ovality))	-	100	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	200	-
7(Finish)	-	200	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	4000	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	4000	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	10000	-
8.2(Reversion Test)	-	600	-
8.3(Density)	-	500	-
8.6(Thermal Stability (Oxidation Induction Time))	-	2000	-
8.7(Volatile Matter Content)	-	500	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	500	-
8.9(Resistance to Weathering)	-	8000	-
6.4(Length of Pipe)	-	200	-
8.4(Melt Flow Rate (MFR))	-	1000	-
8.5(Pigment Dispersion)	-	500	-
8.10(Slow Crack Growth Rate Test)	-	5000	-
8.11(Squeeze-off)	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	500	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1000	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2000	-
5.1, 5.7 Table 2(iv) Volatile content)	-	500	-
5.1, 5.7 Table 2(v) Water content1))	-	500	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	500	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	500	-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
6(Dimensions of pipes)	-	0	-
7(Finish)	-	0	-
8.1(Hydraulic Characteristics)	-	0	-
8.2(Reversion test)	-	0	-
8.3(Density)	-	0	-
8.4(Melt Flow Rate)	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.10(Slow Crack Growth Rate Test)	-	5000	-
8.11(Squeeze-of)	-	0	-
10(Marking)	-	500	-
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	0	-
5.1(Polyethylene compound)	-	0	-
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
5.6(Resistance to Weathering)	-	0	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	0	-
7(Finish)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
8.2(Reversion Test)	-	0	-
8.3(Density)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.9(Resistance to Weathering)	-	0	-
6.4(Length of Pipe)	-	0	-
8.4(Melt Flow Rate (MFR))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-off)	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
6(Dimensions of pipes)	-	0	-
7(Finish)	-	0	-
8.1(Hydraulic Characteristics)	-	0	-
8.2(Reversion test)	-	0	-
8.3(Density)	-	0	-
8.4(Melt Flow Rate)	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-of)	-	0	-
10(Marking)	-	0	-
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	0	-
5.1(Polyethylene compound)	-	0	-
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
5.6(Resistance to Weathering)	-	0	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	0	-
7(Finish)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
8.2(Reversion Test)	-	0	-
8.3(Density)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.9(Resistance to Weathering)	-	0	-
6.4(Length of Pipe)	-	0	-
8.4(Melt Flow Rate (MFR))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-off)	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
6(Dimensions of pipes)	-	0	-
7(Finish)	-	0	-
8.1(Hydraulic Characteristics)	-	0	-
8.2(Reversion test)	-	0	-
8.3(Density)	-	0	-
8.4(Melt Flow Rate)	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-of)	-	0	-
10(Marking)	-	0	-
4.2(Grade of material)	-	0	-
4.3(Nominal Diameter)	-	0	-
4.4(Colour)	-	0	-
5.1(Polyethylene compound)	-	0	-
5.3(Anti-oxidant)	-	0	-
5.4(U-V stabilizer)	-	0	-
5.7(PE Compound Quality Evaluation)	-	0	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	0	-
5.6(Resistance to Weathering)	-	0	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	0	-
6.1(Out of Roundness (Ovality))	-	0	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	0	-
7(Finish)	-	0	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	-
8.2(Reversion Test)	-	0	-
8.3(Density)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.9(Resistance to Weathering)	-	0	-
6.4(Length of Pipe)	-	0	-
8.4(Melt Flow Rate (MFR))	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-off)	-	0	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	0	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	0	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	0	-
5.1, 5.7 Table 2(iv) Volatile content)	-	0	-
5.1, 5.7 Table 2(v) Water content1))	-	0	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	0	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	-
5.3(Anti-Oxidant)	-	0	-
5.4(U.V. Stabilizer)	-	0	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	-
5.6(ii) Hydraulic characteristics)	-	0	-
5.6(iii) Thermal stability (Oxidation induction time))	-	0	-
6(Dimensions of pipes)	-	0	-
7(Finish)	-	0	-
8.1(Hydraulic Characteristics)	-	0	-
8.2(Reversion test)	-	0	-
8.3(Density)	-	0	-
8.4(Melt Flow Rate)	-	0	-
8.5(Pigment Dispersion)	-	0	-
8.6(Thermal Stability (Oxidation Induction Time))	-	0	-
8.7(Volatile Matter Content)	-	0	-
8.9(Resistance to Weathering)	-	0	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	-
8.10(Slow Crack Growth Rate Test)	-	0	-
8.11(Squeeze-of)	-	0	-
10(Marking)	-	0	-
4.2(Grade of material)	-	-	-
4.3(Nominal Diameter)	-	-	-
4.4(Colour)	-	-	-
5.1(Polyethylene compound)	-	-	-
5.3(Anti-oxidant)	-	-	-
5.4(U-V stabilizer)	-	-	-
5.7(PE Compound Quality Evaluation)	-	-	-
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	-	-
5.6(Resistance to Weathering)	-	-	-
6.1(Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-	-	-
6.1(Out of Roundness (Ovality))	-	-	-
6.2(Wall thickness (Take 8 reading and Average will be repoted))	-	-	-
7(Finish)	-	-	-
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	-	-
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	-	-
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	-	-
8.2(Reversion Test)	-	-	-
8.3(Density)	-	-	-
8.6(Thermal Stability (Oxidation Induction Time))	-	-	-
8.7(Volatile Matter Content)	-	-	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	-	-
8.9(Resistance to Weathering)	-	-	-
6.4(Length of Pipe)	-	-	-
8.4(Melt Flow Rate (MFR))	-	-	-
8.5(Pigment Dispersion)	-	-	-
8.10(Slow Crack Growth Rate Test)	-	-	-
8.11(Squeeze-off)	-	-	-
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	-	-
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	-	-
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	-	-
5.1, 5.7 Table 2(iv) Volatile content)	-	-	-
5.1, 5.7 Table 2(v) Water content1))	-	-	-
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	-	-
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	-	-
5.3(Anti-Oxidant)	-	-	-
5.4(U.V. Stabilizer)	-	-	-
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	-	-
5.6(ii) Hydraulic characteristics)	-	-	-
5.6(iii) Thermal stability (Oxidation induction time))	-	-	-
6(Dimensions of pipes)	-	-	-
7(Finish)	-	-	-
8.1(Hydraulic Characteristics)	-	-	-
8.2(Reversion test)	-	-	-
8.3(Density)	-	-	-
8.4(Melt Flow Rate)	-	-	-
8.5(Pigment Dispersion)	-	-	-
8.6(Thermal Stability (Oxidation Induction Time))	-	-	-
8.7(Volatile Matter Content)	-	-	-
8.9(Resistance to Weathering)	-	-	-
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	-	-
8.10(Slow Crack Growth Rate Test)	-	-	-
8.11(Squeeze-of)	-	-	-
10(Marking)	-	-	-

-
Included w.e.f 16.12.2025 Exclusion: 5.3 (Anti-oxidant), 5.4 (U-V stabilizer), 8.11 (Squeeze-off)

IS 2553 : Part 2 (2019)

Safety glass - Specification: Part 2 for road transport (First Revision)

Safety glass - Specification: Part 2 for road transport

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Light Transmittance)	-	4900	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.1.1(Light Transmittance)	-	4700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.1.2.1(Resistance to Abrasion)	-	7000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.1.2.2(Resistance to Abrasion)	-	7000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.1.2.3.1(Resistance to Abrasion)	-	1800	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.1.2.3.1(Resistance to Abrasion)	-	7500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.1.2.3.2(Resistance to Abrasion)	-	7500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.1.2.3.2(Resistance to Abrasion)	-	7000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.2.1(Resistance to Temperature Changes)	-	3400	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.2.2(a) Resistance to Fire)	-	7000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.2.2(b) Resistance to Fire)	-	7000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.3.1 (Resistance to Radiation)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.3.2(Resistance to High Temperature)	-	2000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.3.3.1(Resistance to Humidity)	-	23500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.3.3.2(Resistance to Humidity)	-	23500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.3.3.2(Resistance to Humidity)	-	23500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.3.3.3(Resistance to Humidity)	-	6500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.1(Optical Distortion)	-	5700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.1.3 (Optical Distortion)	-	5700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.2(Secondary image separation test-Vehicle Category M1 and N -Zone A)	-	5700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.2(Secondary image separation test-Vehicle Category M1 and N -Zone B)	-	5700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.2(Secondary image separation test-Vehicle Category L -Zone Primary area)	-	5700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.2(Secondary image separation test-Vehicle Category L -Zone Secondary area)	-	5700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.2(Secondary image separation test-Vehicle Category M2 , M3 and N -central area)	-	5700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.2.3(Secondary image separation test)	-	5700	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.3.1(Head-form Test (Location of crack))	-	7000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.3.2(Head-form Test (Interlayer adhesion))	-	7000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.3.3.1(Head-form Test)	-	7200	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.3.3.2(Head-form Test)	-	7200	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.4(2.260 g Ball)	-	5000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.5.1(227 g Ball)	-	5000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.5.2(227 g Ball)	-	5000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.5.3(227 g Ball)	-	5000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.5.4(227 g Ball)	-	5000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.1.1.1(Fragmentation Test)	-	4000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.1.1.4(Fragmentation Test)	-	4000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.1.1.5(Fragmentation Test)	-	4000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.1.1.5.1(Fragmentation Test)	-	4000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.1.1.5.2(Fragmentation Test)	-	4000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.1.2(227 g ball test)	-	1900	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.2.1.1(227 g ball test)	-	600	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.2.1.2(227 g ball test)	-	600	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.2.1.3(227 g ball test)	-	600	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.1(equirements Applicable only to Double-Glazed Units-Individual components)	-	5500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.2.1( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.2.2.1( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.2.2.2( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.2.2.3( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.2.3-a( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.2.3-b-1( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.2.3-b-2( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.5.3.2.3-b-3( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.1.7( Head-form Test)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.1.8( Head-form Test-The HIC value )	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.2.4-a(Mechanical Strength Test — 227g Ball)	-	6000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.2.4-b(Mechanical Strength Test — 227g Ball)	-	6000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.2.5(Mechanical Strength Test — 227g Ball test at –18° ± 2°C)	-	6000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.2.5(Mechanical Strength Test — 227g Ball test at –18° ± 2°C)	-	6000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.3.3(Flexibility and Fold Test)	-	7500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.4.4-a(Weathering)	-	9500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.4.4-b(Weathering)	-	9500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.5.3-a(Cross-cut)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.6.5.3-b-1(Cross-cut)	-	9000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.7.1.1(227 g Ball Test at 20 ± 5°C)	-	6000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.7.2.1(227g Ball Test at –18° ± 2°C)	-	6000	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.7.3.1(Flexibility Test and Fold Test)	-	8500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.7.3.1(Flexibility Test and Fold Test)	-	8500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.5(227 g Ball test)	-	7500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
As per Clause 3.7(Wind screen and Panes)	-	23500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
As per Clause 4.1(Wind screen and Panes)	-	23500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
As per Clause 5.8.2(Wind screen)	-	9500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
As per Clause 5.8.3(Wind screen)	-	9500	Toughened Glass for panes: - 11,000/- Laminated safety glass for panes: - 75,000/- Laminated safety glass for windscreen: - 87,000/- Toughened glass for windscreen: - 15,000/- Plastic glazing: - 139,000/-
5.4.3.1(Head-form Test (Location of crack))	-	0	-
5.4.3.2(Head-form Test (Interlayer adhesion))	-	0	-
5.4.5(227 g Ball test)	-	0	-
As per Clause 3.7(Wind screen and Panes)	-	0	-
As per Clause 4.1(Wind screen and Panes)	-	0	-
As per Clause 5.8.2(Wind screen)	-	0	-
As per Clause 5.8.3(Wind screen)	-	0	-
5.4.3.1(Head-form Test (Location of crack))	-	0	-
5.4.3.2(Head-form Test (Interlayer adhesion))	-	0	-
5.4.5(227 g Ball test)	-	0	-
As per Clause 3.7(Wind screen and Panes)	-	0	-
As per Clause 4.1(Wind screen and Panes)	-	0	-
As per Clause 5.8.2(Wind screen)	-	0	-
As per Clause 5.8.3(Wind screen)	-	0	-
5.4.3.1(Head-form Test (Location of crack))	-	0	-
5.4.3.2(Head-form Test (Interlayer adhesion))	-	0	-
5.4.5(227 g Ball test)	-	0	-
As per Clause 3.7(Wind screen and Panes)	-	0	-
As per Clause 4.1(Wind screen and Panes)	-	0	-
As per Clause 5.8.2(Wind screen)	-	0	-
As per Clause 5.8.3(Wind screen)	-	0	-

-
Included w.e.f 28.07.2025

IS 2553 : Part 1 (2018)

Safety glass - Specification: Part 1 architectural, building and general uses (Fourth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Types)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.1.1(General)	-	4500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.1.2(Optical Faults-IS 14900)	-	1200	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	1200	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.1.2(Reams, Strings and Lines-IS 14900)	-	1200	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.1.2(Linear / Extended Faults -IS 14900)	-	1200	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.1 (Thickness -IS 17004 & IS 14900)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.2.1( Dimensions- Width )	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.2.1( Dimensions- Length)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.2.2( Squareness)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.3 (Fragmentation Test- IS 17004)	-	5000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.4-a( Flatness-Overall bow-IS 17004)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.4-c( Flatness-Edge lift-IS 17006)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.4-d( Flatness-Local distortion-IS 17007)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.4.1 (Other distortions)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.5.1( Resistance to shock- IS 17004)	-	3200	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.5.2( Resistance to human impact- IS 17004)	-	9900	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.6( Surface Compression (Optional)- IS 17004)	-	0	Exclusion: Surface compression test facility not available.
5.2.7( Mechanical Strength — Four Point Bending Test (Optional)- IS 17004)	-	10000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	5000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.2.8.3-Table 8(Deviations on position of holes and Cutouts Location)	-	5000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.1 (Thickness-IS 17004 & IS 14900)	-	2000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.2.1( Dimensions and squareness- Width )	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.2.1( Dimensions and squareness- Length)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.2.1( Dimensions and squareness-Squareness)	-	1000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.2.2 (Edge displacement)	-	2200	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.3( Light Stability Test-IS 17004)	-	9500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.3( Light Stability Test-IS 17004)	-	9500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.4( Boil and Bake Tests-IS 17004)	-	3000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	3300	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.6.1( Spot defects in the central area)	-	500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.6.2 (Linear defects in the central area)	-	500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.6.3( Defects in the outer area for framed edges)	-	500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.6.4( Vents)	-	500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.6.5( Creases and streaks)	-	500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.6.6( Defects on edge which will not be framed)	-	500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.7( Humidity Test – Optional)	-	31000	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
5.3.8( Resistance to Human Impact Test)	-	9500	Toughened safety glass for (mandatory test)- 20000/-, Laminated safety glass for (mandatory test)- 43,000, Toughened safety glass (including optional tests)- 50,000/-, Laminated safety glass (including optional test)- 80,000/-
4(Types)	-	0	-
5.1.1(General)	-	0	-
5.1.2(Optical Faults-IS 14900)	-	0	-
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	0	-
5.1.2(Reams, Strings and Lines-IS 14900)	-	0	-
5.1.2(Linear / Extended Faults -IS 14900)	-	0	-
5.2.1 (Thickness -IS 17004 & IS 14900)	-	0	-
5.2.2.1( Dimensions- Width )	-	0	-
5.2.2.1( Dimensions- Length)	-	0	-
5.2.2.2( Squareness)	-	0	-
5.2.3 (Fragmentation Test- IS 17004)	-	0	-
5.2.4-a( Flatness-Overall bow-IS 17004)	-	0	-
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	0	-
5.2.4-c( Flatness-Edge lift-IS 17006)	-	0	-
5.2.4-d( Flatness-Local distortion-IS 17007)	-	0	-
5.2.4.1 (Other distortions)	-	0	-
5.2.5.1( Resistance to shock- IS 17004)	-	0	-
5.2.5.2( Resistance to human impact- IS 17004)	-	0	-
5.2.6( Surface Compression (Optional)- IS 17004)	-	0	-
5.2.7( Mechanical Strength — Four Point Bending Test (Optional)- IS 17004)	-	0	-
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	0	-
5.2.8.3-Table 8(Deviations on position of holes and Cutouts Location)	-	0	-
5.3.1 (Thickness-IS 17004 & IS 14900)	-	0	-
5.3.2.1( Dimensions and squareness- Width )	-	0	-
5.3.2.1( Dimensions and squareness- Length)	-	0	-
5.3.2.1( Dimensions and squareness-Squareness)	-	0	-
5.3.2.2 (Edge displacement)	-	0	-
5.3.3( Light Stability Test-IS 17004)	-	0	-
5.3.3( Light Stability Test-IS 17004)	-	0	-
5.3.4( Boil and Bake Tests-IS 17004)	-	0	-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	0	-
5.3.6.1( Spot defects in the central area)	-	0	-
5.3.6.2 (Linear defects in the central area)	-	0	-
5.3.6.3( Defects in the outer area for framed edges)	-	0	-
5.3.6.4( Vents)	-	0	-
5.3.6.5( Creases and streaks)	-	0	-
5.3.6.6( Defects on edge which will not be framed)	-	0	-
5.3.7( Humidity Test – Optional)	-	0	-
5.3.8( Resistance to Human Impact Test)	-	0	-
5.2.1(Thickness)	-	0	-
5.2.2(Dimension and Squarenes)	-	0	-
5.2.4(Overall Bow)	-	0	-
5.2.4(Measurement of wave and roller wave)	-	0	-
5.2.4(Edge lift)	-	0	-
5.2.4(Local distortion)	-	0	-
5.2.3(Fragmentation test)	-	0	-
5.2.7(Four point bending)	-	0	-
5.2.6(Surface compression)	-	0	-
5.2.5.1(Resistance to shock)	-	0	-
5.2.5.2(Resistance to human impact)	-	0	-
5.3.1(Thickness test)	-	0	-
5.3.2.1(Dimension and Squarenes test)	-	0	-
5.3.6(Defects in central area test)	-	0	-
5.3.6.7(Defects in central area test)	-	0	-
5.3.5(Fracture and adhesion)	-	0	-
5.3.8(Resistance to human impact)	-	0	-
5.3.4(Boil test)	-	0	-
5.3.4(Bake test)	-	0	-
5.3.7(Humidity test with condensation)	-	0	-
5.3.7(Humidity test without condensation)	-	0	-
5.3.3(Light stability test)	-	0	-
5.3.2.2(Edge displacement test)	-	0	-
5.2.2(5.2.2 Dimension and Squarenes test)	-	0	-
5.2.4(measurement of wave and roller wave)	-	0	-
5.2.8(Fabrication in Glass)	-	0	-
Cl. No. 5.2.2.3.1, Table No. 1A(Shape accuracy, girth and length)	-	0	-
Cl. No. 5.2.2.3.2(Edge straightness deviation)	-	0	-
Cl. No. 5.2.2.3.3(Maximum cross-curve deviation)	-	0	-
As per Clause 5.3.9(Laminated Glass)	-	0	-
As per Clause 5.2.8.2(Toughened)	-	0	-
As per Clause 5.2.8.4(Toughened)	-	0	-
As per Clause 5.2.9(Toughened)	-	0	-
As per Clause 5.3.6.4(Laminated Glass)	-	0	-
As per Clause 5.3.6.5(Laminated Glass)	-	0	-
As per Clause 5.3.6.6(Laminated Glass)	-	0	-
As per Clause 5.5.2.1(Laminated Glass and Glass-Plastic Panes)	-	0	-
As per Clause 5.5.3.2(Laminated Glass and Glass-Plastic Panes)	-	0	-
As per Clause 5.6.2(Rigid Plastic Glazing)	-	0	-
As per Clause 5.7.1(Flexible Plastic)	-	0	-
As per Clause 3.7(Wind screen and Panes)	-	0	-
As per Clause 4.1(Wind screen and Panes)	-	0	-

-
Included w.e.f.04.07.2025 Cl 5.2.6 ( Surface Compression (Optional)- IS 17004)

IS 17550 : Part 2 (2024)

Household Refrigerating Appliances - Characteristics and Test Methods Part 2 Performance Requirements (First Revision)

Household Refrigerating Appliances- Refrigerators

320000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Storage Test)	-	54000	-
7(Cooling Capacity Test)	-	38000	-
8(Freezing Capacity Test)	-	36000	-
9("Automatic Ice-Making Capacity Test")	-	36000	-
Cl. No.4.6 & Annex A(PULL-DOWN TEST)	-	39000	-
Cl. No.4.6(b) & Annex B("Wine Storage Appliances And Compartments; Storage Test")	-	39000	-
Cl. No.4.6(C) & AnnexC("Temperature Rise Test ")	-	39000	-
Cl. No.4.6(d) & Annex D("Water Vapour Condensation Test ")	-	39000	-

-
-

IS 17550 : Part 1 (2024)

Household Refrigerating Appliances - Characteristics and Test Methods Part 1 General Requirements (First Revision)

Household Refrigerating Appliances- Refrigerators

210000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(MARKING)	-	2000	-
8(MATERIALS, DESIGN, AND MANUFACTURE)	-	11000	-
9(Testing The Air Tightness Of Door Or Lid Seal(S))	-	3000	-
10(Testing The Opening Force Of Door(S) Or Lid(S))	-	7000	-
11(Testing The Durability Of Hinges And Handles Of Door(S) And Lid(S)	-	25000	-
12(Testing The Mechanical Strength Of Shelves And Similar Components)	-	9000	-
14(Ice-Making Test (If Applicable))	-	25000	-
15(Test For Absence Of Odour And Taste)	-	41000	-
16(Safety Requirements)	-	50000	-

-
-

IS 2835 (1987)

Specification for flat transparent sheet glass (Third Revision)

Flat transparent sheet glass

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CLASSIFICATION)	-	100	-
4.1(Material)	-	700	-
4.1.1(Material)	-	700	-
4.2-Table 1 & Cl 5.1(Thickness )	-	1500	-
4.2-Table 1(Length )	-	1700	-
4.2-Table 1(Width)	-	1500	-
4.3-Table 2-i(Gaseous inclusion)	-	900	-
4.3-Table 2-ii(Opaque gaseous inclusion)	-	1100	-
4.3-Table 2-iii(Knots, dirts and stones)	-	1100	-
4.3-Table 2-iv & Cl 5.2(Scratches, rubs and crush)	-	1100	-
4.3-Table 2-v & Cl 5.3(Bow)	-	1100	-
4.3-Table 2-vi & Cl 5.4(Reams, Light Strings and lines)	-	1300	-
4.3-Table 2-vii(Waviness)	-	1300	-
4.3-Table 2-viii(Sulphur stains)	-	1300	-
4.3-Table 2-ix(Corner breakage and chip)	-	1300	-
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Central area)	-	1300	-
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Outer area)	-	1300	-
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Central area)	-	1300	-
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Outer area)	-	1300	-
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Central area)	-	1300	-
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Outer area)	-	1300	-
3.1(CLASSIFICATION)	-	0	-
4.1(Material)	-	0	-
4.1.1(Material)	-	0	-
4.2-Table 1 & Cl 5.1(Thickness )	-	0	-
4.2-Table 1(Length )	-	0	-
4.2-Table 1(Width)	-	0	-
4.3-Table 2-i(Gaseous inclusion)	-	0	-
4.3-Table 2-ii(Opaque gaseous inclusion)	-	0	-
4.3-Table 2-iii(Knots, dirts and stones)	-	0	-
4.3-Table 2-iv & Cl 5.2(Scratches, rubs and crush)	-	0	-
4.3-Table 2-v & Cl 5.3(Bow)	-	0	-
4.3-Table 2-vi & Cl 5.4(Reams, Light Strings and lines)	-	0	-
4.3-Table 2-vii(Waviness)	-	0	-
4.3-Table 2-viii(Sulphur stains)	-	0	-
4.3-Table 2-ix(Corner breakage and chip)	-	0	-
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Central area)	-	0	-
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Outer area)	-	0	-
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Central area)	-	0	-
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Outer area)	-	0	-
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Central area)	-	0	-
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Outer area)	-	0	-
3.1(CLASSIFICATION)	-	0	-
4.1(Material)	-	0	-
4.1.1(Material)	-	0	-
4.2-Table 1 & Cl 5.1(Thickness )	-	0	-
4.2-Table 1(Length )	-	0	-
4.2-Table 1(Width)	-	0	-
4.3-Table 2-i(Gaseous inclusion)	-	0	-
4.3-Table 2-ii(Opaque gaseous inclusion)	-	0	-
4.3-Table 2-iii(Knots, dirts and stones)	-	0	-
4.3-Table 2-iv & Cl 5.2(Scratches, rubs and crush)	-	0	-
4.3-Table 2-v & Cl 5.3(Bow)	-	0	-
4.3-Table 2-vi & Cl 5.4(Reams, Light Strings and lines)	-	0	-
4.3-Table 2-vii(Waviness)	-	0	-
4.3-Table 2-viii(Sulphur stains)	-	0	-
4.3-Table 2-ix(Corner breakage and chip)	-	0	-
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Central area)	-	0	-
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Outer area)	-	0	-
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Central area)	-	0	-
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Outer area)	-	0	-
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Central area)	-	0	-
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Outer area)	-	0	-
3.1(CLASSIFICATION)	-	0	-
4.1(Material)	-	0	-
4.1.1(Material)	-	0	-
4.2-Table 1 & Cl 5.1(Thickness )	-	0	-
4.2-Table 1(Length )	-	0	-
4.2-Table 1(Width)	-	0	-
4.3-Table 2-i(Gaseous inclusion)	-	0	-
4.3-Table 2-ii(Opaque gaseous inclusion)	-	0	-
4.3-Table 2-iii(Knots, dirts and stones)	-	0	-
4.3-Table 2-iv & Cl 5.2(Scratches, rubs and crush)	-	0	-
4.3-Table 2-v & Cl 5.3(Bow)	-	0	-
4.3-Table 2-vi & Cl 5.4(Reams, Light Strings and lines)	-	0	-
4.3-Table 2-vii(Waviness)	-	0	-
4.3-Table 2-viii(Sulphur stains)	-	0	-
4.3-Table 2-ix(Corner breakage and chip)	-	0	-
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Central area)	-	0	-
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Outer area)	-	0	-
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Central area)	-	0	-
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Outer area)	-	0	-
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Central area)	-	0	-
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Outer area)	-	0	-

-
Included w.e.f. 04.08.2025

IS 2553 : Part 3 (2019)

Safety glass - Specification: Part 3 solar applications

74000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	4500	-
4.2 & 6(Dimensions)	-	4500	-
4.2 & 6(Squareness)	-	4500	-
4.2 & 6(Flatness)	-	4500	-
4.2 & 6(Fragmentation)	-	14000	-
4.2 & 6(Resistance to Shock (Ball Drop))	-	23500	-
4.2 & 6(Mechanical Strength)	-	14500	-
4.2 & 6(Hail Strength)	-	24000	Additional Charges for Hail Strength (Optional Requirement) Rs 24000. Complete testing charges Including optional requirement (Hail Strength) Rs 98000.
5.2(Marking)	-	2000	-
As per Clause 6, Table 5(Solar Glas)	-	2000	-

-
Included w.e.f 28.07.2025

IS 14900 (2018)

Transparent float glass - Specification (First Revision)

48000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	3100	-
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	1800	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	2000	-
Cl.4.3.2.1(the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	1900	-
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	1900	-
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	1900	-
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	1900	-
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	2900	-
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	3400	-
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	14000	-
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	2700	-
Cl.4.7 (Annexure F)(Material may be tested for bloom freedom as per Annex F whenever required by the purchaser.)	-	0	Exclusion Cl. 4.7 Bloom Test (Optional Requirement)
4.3.1(Thickness)	-	2000	-
4.3.1(Thickness test)	-	2000	-
4.3.1(Thickness test)	-	2000	-
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	0	-
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	0	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	0	-
Cl.4.3.2.1(the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	0	-
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	0	-
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	0	-
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	0	-
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	0	-
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	0	-
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	0	-
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	0	-
Cl.4.7 (Annexure F)(Material may be tested for bloom freedom as per Annex F whenever required by the purchaser.)	-	0	-
4.3.1(Thickness)	-	0	-
4.3.1(Thickness test)	-	0	-
4.3.1(Thickness test)	-	0	-

-
Included w.e.f.31.07.2025 Exclusion Cl.4.7 (Annexure F) (Material may be tested for bloom freedom as per Annex F whenever required by the purchaser.)

IS/IEC 60529 (2001)

Degrees of protection provided by enclosures (IP Code)

21500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Degrees of protection against access to hazardous parts and against solid foreign objects indicated by the first characteristic numeral)	-	10500	-
Cl-5.1(Protection against access to hazardous parts)	-	8000	-
Cl-5.2(Protection against solid foreign objects)	-	8000	-
Cl-6(Degrees of protectlon against ingress of water indicated 'by the second characteristic numeral)	-	7500	-
Cl-7(Degrees of protection against access to hazardous parts indicated by the additional letter)	-	10500	-
Cl-8(Supplementary letter)	-	8000	-
Cl-10(Marking)	-	5500	-

-
Included w.e.f 19.06.2025

IS 302 : Part 2 : Sec 75 (2018)

Safety of Household and Similar Electrical Appliances Part 2 Particular Requirements Section 75 Commercial Dispensing Appliances and Vending Machines

Commercial Dispensing Appliances and Vending Machines

32000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation, toxicity and similar hazards)	-	1000	-
31(Resistance to rusting)	-	1000	-
30.2.4(Resistance to heat and fire)	-	2000	-
30.2(Resistance to heat and fire)	-	2000	-
30.1(Resistance to heat and fire)	-	2000	-
29.3(Clearances, creepage distances and solid insulation)	-	2000	-
29.2(Clearances, creepage distances and solid insulation)	-	2000	-
29.2(Clearances, creepage distances and solid insulation)	-	0	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	2000	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	0	-
28.2 to 28.4(Screws and connections)	-	1000	-
28.1, Table No.-14(Screws and connections)	-	1000	-
27.6(Provision for earthing)	-	2000	-
27.5(Provision for earthing)	-	2000	-
27.1 to 27.4(Provision for earthing)	-	2000	-
26.10 & 26.11(Terminals for external conductors)	-	1000	-
26.9(Terminals for external conductors)	-	1000	-
26.1 to 26.8(Terminals for external conductors)	-	1000	-
25.16 to 25.25(Supply connection and external flexible cords)	-	1000	-
25.15(Supply connection and external flexible cords)	-	1000	-
25.14(Supply connection and external flexible cords)	-	1000	-
25.9 to 25.13(Supply connection and external flexible cords)	-	1000	-
25.8, Table No.-11(Supply connection and external flexible cords)	-	1000	-
24.101 to 24.103(Components)	-	3000	-
25.5 to 25.7(Supply connection and external flexible cords)	-	1000	-
25.4(Supply connection and external flexible cords)	-	1000	-
25.3(Supply connection and external flexible cords)	-	1000	-
25.2(Supply connection and external flexible cords)	-	1000	-
25.1(Supply connection and external flexible cords)	-	1000	-
24.2 to 24.6(Components)	-	3000	-
24.1(Components)	-	3000	-
23.101 to 23.102(Internal wiring)	-	1000	-
23.6 to 23.10(Internal wiring)	-	1000	-
23.5(Internal wiring)	-	1000	-
23.4(Internal wiring)	-	1000	-
23.3(Internal wiring)	-	1000	-
23.1 & 23.2(Internal wiring)	-	1000	-
22.101 to 22.114(Constructions)	-	5000	-
22.13 to 22.48(Constructions)	-	5000	-
22.12(Constructions)	-	5000	-
22.11(Constructions)	-	5000	-
22.11(Constructions)	-	5000	-
22.7 to 22.10(Constructions)	-	5000	-
22.6(Constructions)	-	5000	-
22.5(Constructions)	-	0	EMI/EMC test facility not available.
22.4(Constructions)	-	5000	-
22.3(Constructions)	-	5000	-
22.2(Constructions)	-	5000	-
22.1(Constructions)	-	5000	-
21.2(MECHANICAL STRENGTH)	-	2000	-
21.1(MECHANICAL STRENGTH)	-	2000	-
20.2(Stability and mechanical hazards)	-	1000	-
20.1(Stability and mechanical hazards)	-	1000	-
19.101 and 19.102(ABNORMAL OPERATION)	-	2000	-
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	2000	-
17(Overload protection of transformers and associated circuits)	-	2000	-
16.3(Insulation resistance test)	-	1000	-
16.3(Electric strength test)	-	1000	-
16.1 & 16.2(Leakage current test)	-	1000	-
15.102(Moisture resistance)	-	1000	-
15.102(Moisture resistance)	-	1000	-
15.101(Moisture resistance)	-	1000	-
15.3(Moisture resistance)	-	1000	-
15.1(Moisture resistance)	-	4900	-
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	1000	-
13.3 and Table No.- 4(Electric strength test)	-	1000	-
13.1, 13.2(Leakage current test)	-	1000	-
11.1 to 11.8, Table No.-3(Heating)	-	1000	-
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	1000	-
8.1.5(Protection against access to live parts)	-	1000	-
8.1.4(Protection against access to live parts)	-	1000	-
8.1.3(Protection against access to live parts)	-	1000	-
8.1.2(Protection against access to live parts)	-	1000	-
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	1000	-
7.14(Legibility & Durability of Markings test)	-	500	-
7.1 to 7.13, 7.15, 7.16(Marking)	-	500	-
32(Radiation, toxicity and similar hazards)	-	1000	-
31(Resistance to rusting)	-	1000	-
30.2.4(Resistance to heat and fire)	-	2000	-
30.2(Resistance to heat and fire)	-	2000	-
30.1(Resistance to heat and fire)	-	2000	-
29.3(Clearances, creepage distances and solid insulation)	-	2000	-
29.2(Clearances, creepage distances and solid insulation)	-	2000	-
29.2(Clearances, creepage distances and solid insulation)	-	0	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	2000	-
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	0	-
28.2 to 28.4(Screws and connections)	-	1000	-
28.1, Table No.-14(Screws and connections)	-	1000	-
27.6(Provision for earthing)	-	2000	-
27.5(Provision for earthing)	-	2000	-
27.1 to 27.4(Provision for earthing)	-	2000	-
26.10 & 26.11(Terminals for external conductors)	-	1000	-
26.9(Terminals for external conductors)	-	1000	-
26.1 to 26.8(Terminals for external conductors)	-	1000	-
25.16 to 25.25(Supply connection and external flexible cords)	-	1000	-
25.15(Supply connection and external flexible cords)	-	1000	-
25.14(Supply connection and external flexible cords)	-	1000	-
25.9 to 25.13(Supply connection and external flexible cords)	-	1000	-
25.8, Table No.-11(Supply connection and external flexible cords)	-	1000	-
25.5 to 25.7(Supply connection and external flexible cords)	-	1000	-
25.4(Supply connection and external flexible cords)	-	1000	-
25.3(Supply connection and external flexible cords)	-	1000	-
25.2(Supply connection and external flexible cords)	-	1000	-
25.1(Supply connection and external flexible cords)	-	1000	-
24.101 to 24.103(Components)	-	3000	-
24.2 to 24.6(Components)	-	3000	-
24.1(Components)	-	3000	-
23.101 to 23.102(Internal wiring)	-	1000	-
23.6 to 23.10(Internal wiring)	-	1000	-
15.2(Moisture resistance)	-	1000	-
23.5(Internal wiring)	-	1000	-
23.4(Internal wiring)	-	1000	-
23.3(Internal wiring)	-	1000	-
23.1 & 23.2(Internal wiring)	-	1000	-
22.101 to 22.114(Constructions)	-	5000	-
22.13 to 22.48(Constructions)	-	5000	-
22.12(Constructions)	-	5000	-
22.11(Constructions)	-	5000	-
22.11(Constructions)	-	5000	-
22.7 to 22.10(Constructions)	-	5000	-
22.6(Constructions)	-	5000	-
22.5(Constructions)	-	0	EMI/EMC test facility not available
22.4(Constructions)	-	5000	-
22.3(Constructions)	-	5000	-
22.2(Constructions)	-	5000	-
22.1(Constructions)	-	5000	-
21.2(MECHANICAL STRENGTH)	-	2000	-
21.1(MECHANICAL STRENGTH)	-	2000	-
20.2(Stability and mechanical hazards)	-	1000	-
20.1(Stability and mechanical hazards)	-	1000	-
19.101 and 19.102(ABNORMAL OPERATION)	-	2000	-
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	2000	-
17(Overload protection of transformers and associated circuits)	-	2000	-
16.3(Insulation resistance test)	-	1000	-
16.3(Electric strength test)	-	1000	-
16.1 & 16.2(Leakage current test)	-	1000	-
15.102(Moisture resistance)	-	1000	-
15.102(Moisture resistance)	-	1000	-
15.101(Moisture resistance)	-	1000	-
15.3(Moisture resistance)	-	1000	-
15.2(Moisture resistance)	-	1000	-
15.1(Moisture resistance)	-	4900	-
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	1000	-
13.3 and Table No.- 4(Electric strength test)	-	1000	-
13.1, 13.2(Leakage current test)	-	1000	-
11.1 to 11.8, Table No.-3(Heating)	-	1000	-
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	1000	-
8.1.5(Protection against access to live parts)	-	1000	-
8.1.4(Protection against access to live parts)	-	1000	-
8.1.3(Protection against access to live parts)	-	1000	-
8.1.2(Protection against access to live parts)	-	1000	-
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	1000	-
7.14(Legibility & Durability of Markings test)	-	500	-
7.1 to 7.13, 7.15, 7.16(Marking)	-	500	-
19.11.4.1(Electrostatic discharges)	-	0	EMI/EMC Test facility not available
19.11.4.2(Radiated fields)	-	0	EMI/EMC Test facility not available
19.11.4.3(Fast transient bursts)	-	0	EMI/EMC Test facility not available
19.11.4.4(Surge immunity test)	-	0	EMI/EMC Test facility not available
19.11.4.5(Immunity to conducted discharges)	-	0	EMI/EMC Test facility not available
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	EMI/EMC Test facility not available
19.11.4.7(Harmonics)	-	0	EMI/EMC Test facility not available

-
Included w.e.f 30.06.2025 Exclusion: Cl 19.11.4.1-19.11.4.7(EMI/EMC), Cl 22.5 (Constructions)

IS 302 : Part 2 : Sec 4 (1993)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 4 spin extractors

IS 302 (Part2/Sec4)

175000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(GENERAL REQUIREMENTS)	-	2000	-
4(GENERAL NOTES ON TESTS)	-	2000	-
6(CLASSIFICATION)	-	10000	-
7(MARKING)	-	1000	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	2000	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	2000	-
10(INPUT AND CURRENT)	-	10000	-
11(HEATING)	-	2000	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	8000	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	10000	-
15(MOISTURE RESISTANCE)	-	25000	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH (AFTER HUMIDITY TREATMENT))	-	5000	-
17(OVERLOAD PROTECTION)	-	2000	-
19(ABNORMAL OPERATION)	-	5000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	5000	-
21(MECHANICAL STRENGTH)	-	25000	-
22(CONSTRUCTION)	-	10000	-
23(INTERNAL WIRING)	-	2000	-
24(COMPONENTS)	-	8000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	5000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	5000	-
27(PROVISION FOR EARTHING)	-	5000	-
28(SCREWS AND CONNECTIONS)	-	5000	-
19.11.4.2(Radiated fields)	-	0	EMI/EMC test machine not available
19.11.4.3(Fast transient bursts)	-	0	EMI/EMC test machine not available
19.11.4.4(Surge immunity test)	-	0	EMI/EMC test machine not available
19.11.4.5(Immunity to conducted discharges)	-	0	EMI/EMC test machine not available
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	EMI/EMC test machine not available
19.11.4.7(Harmonics)	-	0	EMI/EMC test machine not available
5(RATING)	-	5000	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	2000	-
30(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	40000	-
31(RESISTANCE TO RUSTING)	-	5000	-
19.11.4.1(Electrostatic discharges)	-	0	EMI/EMC test machine not available
3(GENERAL REQUIREMENTS)	-	0	-
4(GENERAL NOTES ON TESTS)	-	0	-
6(CLASSIFICATION)	-	0	-
7(MARKING)	-	0	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	0	-
10(INPUT AND CURRENT)	-	0	-
11(HEATING)	-	0	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	0	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	0	-
15(MOISTURE RESISTANCE)	-	0	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH (AFTER HUMIDITY TREATMENT))	-	0	-
17(OVERLOAD PROTECTION)	-	0	-
19(ABNORMAL OPERATION)	-	0	-
20(STABILITY AND MECHANICAL HAZARDS)	-	0	-
21(MECHANICAL STRENGTH)	-	0	-
22(CONSTRUCTION)	-	0	-
23(INTERNAL WIRING)	-	0	-
24(COMPONENTS)	-	0	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	0	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	0	-
27(PROVISION FOR EARTHING)	-	0	-
28(SCREWS AND CONNECTIONS)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
5(RATING)	-	0	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	0	-
30(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	0	-
31(RESISTANCE TO RUSTING)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-

-
Included w.e.f 23.06.2025 Exclusion: Cl 19.11.4.1-19.11.4.7 (EMI/EMC)

IS 16672 : Part 2 (2017)

Refrigerated display cabinets: Part 2 classification, requirements and test conditions

Refrigerated Display Cabinets Part 2 Classification, Requirements and Test Conditions

300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(General)	-	2500	-
4.1.2(Materials)	-	2500	-
4.1.3(Thermal insulation)	-	2500	-
4.1.4(Refrigerating system)	-	2500	-
4.1.5(Electrical components)	-	50000	-
4.1.6(Temperature display)	-	2500	-
4.2.1(Absence of odour and taste)	-	1000	-
4.2.2(Classification according to temperature)	-	1000	-
4.2.3(Defrosting)	-	1000	-
4.2.4(Water vapour condensation)	-	1000	-
4.2.5(Energy consumption)	-	1000	-
4.2.6(Specific Energy Consumption)	-	1000	-
5.2.1(Seal test for doors and lids on low temperature applications)	-	2500	-
5.2.2(Linear dimensions, areas)	-	3000	-
5.3.1(General conditions)	-	2500	-
5.3.2(Preparation of test cabinet and general test procedures)	-	1000	-
5.3.3(Temperature test)	-	60000	-
5.3.4(Water vapour condensation test)	-	60000	-
5.3.5(Electrical energy consumption test)	-	65000	-
5.3.6("Heat extraction rate measurement when condensing unit is remote from cabinet")	-	45000	-

-
Included w.e.f.16.07.2025

IS 14155 (1994)

Domestic electric clothes washing machines for household use - Specification

Domestic Electric Clothes Washing Machine for Household Use - Specification

159000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
18(Finish)	-	500	-
17(Endurance)	-	5000	-
16(Determination of mechanical detergent loss in the sump of washing machine)	-	5000	-
15(Determination of water and energy consumption)	-	5000	-
14(Determination of the water extraction efficiency)	-	5000	-
13(Determination of water retention percentage (Rinsing efficiency))	-	5000	-
12(Determination of wear suffered by textile)	-	2000	-
11(Determination of the washing performance standard measurement with a load of clean material and standardized soiling)	-	2000	-
Cl.9 (Cl.8 to Cl.32 of IS 302-2-7)(Safety requirement)	-	20000	-
Cl.9 (Cl.24 of IS 302-2-7)(Component)	-	20000	-
Cl.9 (Cl.8 to Cl.32 of IS 302-2-7)(Safety requirement for Washing machine)	-	20000	-
9.1(Spin Extractor safety requirement)	-	35000	-
Cl-9 (Cl-8 of IS 302-2-7)(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	2000	-
Cl-9 (Cl-10 of IS 302-2-7)(POWER INPUT AND CURRENT)	-	2000	-
Cl-9 (Cl-11 of IS 302-2-7)(HEATING)	-	2000	-
Cl-9 (Cl-13 of IS 302-2-7)(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	2000	-
Cl-9 (Cl-14 of IS 302-2-7)(TRANSIENT OVERVOLTAGES)	-	2000	-
Cl-9 (Cl-15 of IS 302-2-7)(MOISTURE RESISTANCE)	-	2000	-
Cl-9 (Cl-16 of IS 302-2-7)(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	2000	-
Cl-9 (Cl-17 of IS 302-2-7)(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	2000	-
Cl-9 (Cl-19 of IS 302-2-7)(ABNORMAL OPERATION)	-	2000	-
Cl-9 (Cl-20 of IS 302-2-7)(STABILITY AND MECHANICAL HAZARDS)	-	2000	-
Cl-9 (Cl-21 of IS 302-2-7)(MECHANICAL STRENGTH)	-	2000	-
Cl-9 (Cl-22 of IS 302-2-7)(CONSTRUCTION)	-	2000	-
Cl-9 (Cl-23 of IS 302-2-7)(INTERNAL WIRING)	-	2000	-
Cl-9 (Cl-24 of IS 302-2-7)(COMPONENTS)	-	5000	-
Cl-9 (Cl-25 of IS 302-2-7)(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2000	-
Cl-9 (Cl-26 of IS 302-2-7)(TERMINALS FOR EXTERNAL CONDUCTORS)	-	2000	-
Cl-9 (Cl-27 of IS 302-2-7)(PROVISION FOR EARTHING)	-	2000	-
Cl-9 (Cl-28 of IS 302-2-7)(SCREWS AND CONNECTIONS)	-	2000	-
Cl-9 (Cl-29 of IS 302-2-7)(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
Cl-9 (Cl-30 of IS 302-2-7)(RESISTANCE TO HEAT AND FIRE)	-	2000	-
Cl-9 (Cl-31 of IS 302-2-7)(RESISTANCE TO RUSTING)	-	2000	-
Cl-9 (Cl-32 of IS 302-2-7)(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	5000	-
Cl-19.11.4.1 of IS 302-2-7(Electrostatic discharge)	-	0	EMI/EMC test facility not available
Cl-19.11.4.2 of IS 302-2-7(Radiated Fields)	-	0	EMI/EMC test facility not available
Cl-19.11.4.3 of IS 302-2-7(Fast transient bursts)	-	0	EMI/EMC test facility not available
Cl-19.11.4.4 of IS 302-2-7(Surge Immunity test)	-	0	EMI/EMC test facility not available
Cl-19.11.4.5 of IS 302-2-7(Immunity to conducted discharge)	-	0	EMI/EMC test facility not available
Cl-19.11.4.6 of IS 302-2-7(Voltage dips and interruptions)	-	0	EMI/EMC test facility not available
Cl-19.11.4.7 of IS 302-2-7(Harmonics)	-	0	EMI/EMC test facility not available
18(Finish)	-	0	-
17(Endurance)	-	0	-
16(Determination of mechanical detergent loss in the sump of washing machine)	-	0	-
15(Determination of water and energy consumption)	-	0	-
14(Determination of the water extraction efficiency)	-	0	-
13(Determination of water retention percentage (Rinsing efficiency))	-	0	-
12(Determination of wear suffered by textile)	-	0	-
11(Determination of the washing performance standard measurement with a load of clean material and standardized soiling)	-	0	-
Cl.9 (Cl.8 to Cl.32 of IS 302-2-7)(Safety requirement)	-	0	-
Cl.9 (Cl.24 of IS 302-2-7)(Component)	-	0	-
Cl.9 (Cl.8 to Cl.32 of IS 302-2-7)(Safety requirement for Washing machine)	-	0	-
9.1(Spin Extractor safety requirement)	-	0	-
Cl-9 (Cl-8 of IS 302-2-7)(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	0	-
Cl-9 (Cl-10 of IS 302-2-7)(POWER INPUT AND CURRENT)	-	0	-
Cl-9 (Cl-11 of IS 302-2-7)(HEATING)	-	0	-
Cl-9 (Cl-13 of IS 302-2-7)(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	0	-
Cl-9 (Cl-14 of IS 302-2-7)(TRANSIENT OVERVOLTAGES)	-	0	-
Cl-9 (Cl-15 of IS 302-2-7)(MOISTURE RESISTANCE)	-	0	-
Cl-9 (Cl-16 of IS 302-2-7)(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	0	-
Cl-9 (Cl-17 of IS 302-2-7)(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	0	-
Cl-9 (Cl-19 of IS 302-2-7)(ABNORMAL OPERATION)	-	0	-
Cl-9 (Cl-20 of IS 302-2-7)(STABILITY AND MECHANICAL HAZARDS)	-	0	-
Cl-9 (Cl-21 of IS 302-2-7)(MECHANICAL STRENGTH)	-	0	-
Cl-9 (Cl-22 of IS 302-2-7)(CONSTRUCTION)	-	0	-
Cl-9 (Cl-23 of IS 302-2-7)(INTERNAL WIRING)	-	0	-
Cl-9 (Cl-24 of IS 302-2-7)(COMPONENTS)	-	0	-
Cl-9 (Cl-25 of IS 302-2-7)(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	0	-
Cl-9 (Cl-26 of IS 302-2-7)(TERMINALS FOR EXTERNAL CONDUCTORS)	-	0	-
Cl-9 (Cl-27 of IS 302-2-7)(PROVISION FOR EARTHING)	-	0	-
Cl-9 (Cl-28 of IS 302-2-7)(SCREWS AND CONNECTIONS)	-	0	-
Cl-9 (Cl-29 of IS 302-2-7)(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	0	-
Cl-9 (Cl-30 of IS 302-2-7)(RESISTANCE TO HEAT AND FIRE)	-	0	-
Cl-9 (Cl-31 of IS 302-2-7)(RESISTANCE TO RUSTING)	-	0	-
Cl-9 (Cl-32 of IS 302-2-7)(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	0	-
Cl-19.11.4.1 of IS 302-2-7(Electrostatic discharge)	-	0	-
Cl-19.11.4.2 of IS 302-2-7(Radiated Fields)	-	0	-
Cl-19.11.4.3 of IS 302-2-7(Fast transient bursts)	-	0	-
Cl-19.11.4.4 of IS 302-2-7(Surge Immunity test)	-	0	-
Cl-19.11.4.5 of IS 302-2-7(Immunity to conducted discharge)	-	0	-
Cl-19.11.4.6 of IS 302-2-7(Voltage dips and interruptions)	-	0	-
Cl-19.11.4.7 of IS 302-2-7(Harmonics)	-	0	-

-
Included w.e.f 23.06.2025 Exclusion: Cl-19.11.4.1-19.11.4.7 of IS 302-2-7(EMI/EMC)

IS 2167 (2024)

Commercial Beverage Coolers - Classification, Requirements and Test Conditions (Third Revision)

Commercial Beverage Coolers – Classification, Requirement and Test Conditions

225000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Classification according to temperature)	-	1000	-
Cl-5.2.1.1(Strength and rigidity)	-	1000	-
Cl-5.2.1.2(Pipes and connections)	-	1000	-
Cl-5.2.2(Materials)	-	7000	-
Cl-5.2.3(Thermal insulation)	-	3000	-
Cl-5.2.4(Refrigerating system)	-	4000	-
Cl-5.2.5(Electrical components)	-	50000	-
Cl-6.2.1(General)	-	1000	-
Cl-6.2.2(Seal test for doors and lids)	-	10000	-
Cl-6.2.3(Test on durability of door and lid.)	-	20000	-
Cl-6.2.4(Linear dimensions, areas and volumes)	-	10000	-
Cl-6.3.2(Test room condition)	-	10000	-
Cl-6.3.3(M-can)	-	10000	-
Cl-6.3.4(Preparation of test commercial beverage cooler and general test procedures)	-	10000	-
Cl-6.3.5(Loading the commercial beverage cooler)	-	10000	-
Cl-6.3.6(Running in period)	-	10000	-
Cl-6.3.7(Stable conditions)	-	10000	-
Cl-6.3.8(Lighting and night-covers)	-	10000	-
Cl-6.3.9(Power supply)	-	1000	-
Cl-6.3.10(Testing several commercial beverage coolers in the same room)	-	1000	-
Cl-6.3.11(Test with M-cans)	-	50000	-
Cl-6.3.12(Water vapour condensation test)	-	50000	-
Cl-6.3.13(Calculation of specific energy consumption (SEC).)	-	10000	-
Cl-6.3.14(Lighting test)	-	10000	-
Cl-6.4(Test report)	-	0	-
Cl-7(Marking)	-	5000	-
Cl-5.1(Classification according to temperature)	-	0	-
Cl-5.2.1.1(Strength and rigidity)	-	0	-
Cl-5.2.1.2(Pipes and connections)	-	0	-
Cl-5.2.2(Materials)	-	0	-
Cl-5.2.3(Thermal insulation)	-	0	-
Cl-5.2.4(Refrigerating system)	-	0	-
Cl-5.2.5(Electrical components)	-	0	-
Cl-6.2.1(General)	-	0	-
Cl-6.2.2(Seal test for doors and lids)	-	0	-
Cl-6.2.3(Test on durability of door and lid.)	-	0	-
Cl-6.2.4(Linear dimensions, areas and volumes)	-	0	-
Cl-6.3.2(Test room condition)	-	0	-
Cl-6.3.3(M-can)	-	0	-
Cl-6.3.4(Preparation of test commercial beverage cooler and general test procedures)	-	0	-
Cl-6.3.5(Loading the commercial beverage cooler)	-	0	-
Cl-6.3.6(Running in period)	-	0	-
Cl-6.3.7(Stable conditions)	-	0	-
Cl-6.3.8(Lighting and night-covers)	-	0	-
Cl-6.3.9(Power supply)	-	0	-
Cl-6.3.10(Testing several commercial beverage coolers in the same room)	-	0	-
Cl-6.3.11(Test with M-cans)	-	0	-
Cl-6.3.12(Water vapour condensation test)	-	0	-
Cl-6.3.13(Calculation of specific energy consumption (SEC).)	-	0	-
Cl-6.3.14(Lighting test)	-	0	-
Cl-6.4(Test report)	-	0	-
Cl-7(Marking)	-	0	-

-
Included w.e.f 19.06.2025

IS 7872 (2020)

Deep Freezers - Specification ( Second Revision )

Deep Freezers- Specification

149500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.2.12(Temperature rise test)	-	10000	-
10.2.11(Measurement )	-	1000	-
10.2.10.1(Test packages and life time)	-	1000	-
10.2.10(Full load test)	-	1000	-
10.2.8(Earth resistance test )	-	5000	-
10.2.7(Leakage current test )	-	5000	-
10.2.6(Insulation resistance test)	-	5000	-
10.2.5(High voltage test)	-	5000	-
10.2.3(Thermal insulation test )	-	5000	-
10.2.2(Machanical strength of shelves and similar components)	-	5000	-
10.2.1(Door seal test )	-	5000	-
9.2.2(Power consumption & percentage running time)	-	5000	-
9.2.1(Pull down time)	-	5000	-
9.1(No load test)	-	5000	-
6.11(Volume measurement Water fill method)	-	5000	-
6(Measurement of freezer storage capacity)	-	5000	-
5.1(Sound level)	-	5000	-
5.6(External surface condensation test)	-	5000	-
5.5(Strength Pressure test for components)	-	5000	-
4.8(Doors & Fittings)	-	5000	-
13(Marking and Instruction)	-	1000	-
11.7(Pressure Test)	-	10000	-
11.6(Thermal Insulation Test ( External Condensation))	-	10000	-
11.5(Mechanical Strength of Shelves and Similar Components)	-	5000	-
11.4(Door Seal Test)	-	5000	-
11.3(Temperature Rise Test)	-	10000	-
11.2(Energy Consumption Test)	-	10000	-
11.1(No load Pull down Test)	-	10000	-
8(Freezer Storage Capacity)	-	5000	-
7(Sound Pressure Level)	-	2500	-
6(Safety Requirements)	-	50000	-
5.4.4(Fatigue Test)	-	10000	-
5.4.3(Individual Strength - Pressure Test)	-	10000	-
5.4.2(Individual Strength - Pressure Test)	-	10000	-
4.8(Door and Fittings)	-	5000	-
13(Marking and Instruction)	-	1000	-
11.7(Pressure Test)	-	10000	-
11.6(Thermal Insulation Test ( External Condensation))	-	10000	-
11.5(Mechanical Strength of Shelves and Similar Components)	-	5000	-
11.4(Door Seal Test)	-	5000	-
11.3(Temperature Rise Test)	-	10000	-
11.2(Energy Consumption Test)	-	10000	-
11.1(No load Pull down Test)	-	10000	-
8(Freezer Storage Capacity)	-	5000	-
7(Sound Pressure Level)	-	2500	-
6(Safety Requirements)	-	50000	-
5.4.4(Fatigue Test)	-	10000	-
5.4.3(Individual Strength - Pressure Test)	-	10000	-
5.4.2(Individual Strength - Pressure Test)	-	10000	-
4.8(Door and Fittings)	-	5000	-
5(Refrigeration system)	-	46500	-
Cl-4.1(General Design)	-	1000	-
Cl-4.2(Materials)	-	1000	-
Cl-4.3(Finish)	-	5000	-
Cl-4.4(Thermal Insulation)	-	1000	-
Cl-4.5(Fittings)	-	5000	-
Cl-4.6(Hardware)	-	1000	-
Cl-4.7(Interior Fittings)	-	5000	-
Cl-4.8(Doors and Fittings)	-	5000	-
Cl-4.9(Disposal of Defrost / Condensate Water)	-	1000	-
Cl-5.1(Construction)	-	500	-
Cl-5.2(Control of Operation)	-	500	-
Cl-5.3(Location of Components)	-	500	-
6.5(For flammable refrigerant the units should comply with IS/IEC 60335-2-89)	-	50000	-
6.2(The compressor shall comply with the requirements of IS 10617)	-	1000	-
10.2.12(Temperature rise test)	-	0	-
10.2.11(Measurement )	-	0	-
10.2.10.1(Test packages and life time)	-	0	-
10.2.10(Full load test)	-	0	-
10.2.8(Earth resistance test )	-	0	-
10.2.7(Leakage current test )	-	0	-
10.2.6(Insulation resistance test)	-	0	-
10.2.5(High voltage test)	-	0	-
10.2.3(Thermal insulation test )	-	0	-
10.2.2(Machanical strength of shelves and similar components)	-	0	-
10.2.1(Door seal test )	-	0	-
9.2.2(Power consumption & percentage running time)	-	0	-
9.2.1(Pull down time)	-	0	-
9.1(No load test)	-	0	-
6.11(Volume measurement Water fill method)	-	0	-
6(Measurement of freezer storage capacity)	-	0	-
5.1(Sound level)	-	0	-
5.6(External surface condensation test)	-	0	-
5.5(Strength Pressure test for components)	-	0	-
4.8(Doors & Fittings)	-	0	-
13(Marking and Instruction)	-	0	-
11.7(Pressure Test)	-	0	-
11.6(Thermal Insulation Test ( External Condensation))	-	0	-
11.5(Mechanical Strength of Shelves and Similar Components)	-	0	-
11.4(Door Seal Test)	-	0	-
11.3(Temperature Rise Test)	-	0	-
11.2(Energy Consumption Test)	-	0	-
11.1(No load Pull down Test)	-	0	-
8(Freezer Storage Capacity)	-	0	-
7(Sound Pressure Level)	-	0	-
6(Safety Requirements)	-	0	-
5.4.4(Fatigue Test)	-	0	-
5.4.3(Individual Strength - Pressure Test)	-	0	-
5.4.2(Individual Strength - Pressure Test)	-	0	-
4.8(Door and Fittings)	-	0	-
13(Marking and Instruction)	-	0	-
11.7(Pressure Test)	-	0	-
11.6(Thermal Insulation Test ( External Condensation))	-	0	-
11.5(Mechanical Strength of Shelves and Similar Components)	-	0	-
11.4(Door Seal Test)	-	0	-
11.3(Temperature Rise Test)	-	0	-
11.2(Energy Consumption Test)	-	0	-
11.1(No load Pull down Test)	-	0	-
8(Freezer Storage Capacity)	-	0	-
7(Sound Pressure Level)	-	0	-
6(Safety Requirements)	-	0	-
5.4.4(Fatigue Test)	-	0	-
5.4.3(Individual Strength - Pressure Test)	-	0	-
5.4.2(Individual Strength - Pressure Test)	-	0	-
4.8(Door and Fittings)	-	0	-
5(Refrigeration system)	-	0	-
Cl-4.1(General Design)	-	0	-
Cl-4.2(Materials)	-	0	-
Cl-4.3(Finish)	-	0	-
Cl-4.4(Thermal Insulation)	-	0	-
Cl-4.5(Fittings)	-	0	-
Cl-4.6(Hardware)	-	0	-
Cl-4.7(Interior Fittings)	-	0	-
Cl-4.8(Doors and Fittings)	-	0	-
Cl-4.9(Disposal of Defrost / Condensate Water)	-	0	-
Cl-5.1(Construction)	-	0	-
Cl-5.2(Control of Operation)	-	0	-
Cl-5.3(Location of Components)	-	0	-
6.5(For flammable refrigerant the units should comply with IS/IEC 60335-2-89)	-	0	-
6.2(The compressor shall comply with the requirements of IS 10617)	-	0	-

-
Included w.e.f 24.06.2025

IS 1474 (1959)

Specification for commercial refrigerators

Specification for Commercial Refrigerators

284000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.5.8(Door Seal Test)	-	10000	-
7.5.7(Test for Adequate Rating of Compressor Motor)	-	20000	-
7.5.6(Rating Test)	-	20000	-
7.5.5(Condensation Test)	-	15000	-
7.5.4(Thermal Insulation Test)	-	10000	-
7.5.3(Insulation Resistance Test (Assembly Test))	-	10000	-
7.5.1(Pressure Test)	-	15000	-
3.7(Net volume)	-	5000	-
3.6(Computation of shelf area)	-	5000	-
3.5(Volume of fixed shelves and partitions)	-	5000	-
3.3(Volume of evaporator space)	-	5000	-
3.3.1(Gross Volume)	-	5000	-
Cl. 3.4(1474)	-	5000	-
Cl. 4.1(1474)	-	4000	-
Cl. 4.2(1474)	-	4000	-
Cl. 4.3(1474)	-	4000	-
Cl. 4.4(1474)	-	4000	-
Cl. 4.5(1474)	-	3000	-
Cl. 4.6(1474)	-	3000	-
Cl. 4.7(1474)	-	5000	-
Cl. 4.8(1474)	-	6000	-
Cl. 4.9(1474)	-	6000	-
Cl. 4.10(1474)	-	3000	-
Cl. 4.11(1474 Shelves)	-	3000	-
Cl. 4.12(1474)	-	3000	-
Cl. 4.13(1474)	-	6000	-
Cl. 5.1(1474)	-	8000	-
Cl. 5.2(1474)	-	6000	-
Cl. 5.3(1474)	-	10000	-
Cl. 5.4(1474)	-	5000	-
Cl. 5.5(1474)	-	5000	-
Cl. 6.1(1474)	-	4000	-
Cl. 6.2(1474)	-	4000	-
Cl. 6.3(1474)	-	4000	-
Cl. 6.4(1474)	-	4000	-
Cl. 6.5(1474)	-	5000	-
Cl. -6.6(1474)	-	5000	-
Cl. -7.5.2(1474)	-	10000	-
Cl. 9, 9.1-9.3 of IS:1474:1959(1474)	-	5000	-
Cl-3.1(Inside Dimensions)	-	5000	-
Cl-3.2(Dinzengions of the Evaporator Space)	-	5000	-
3.1(Inside Dimensions 3.1.1(Inside Depth), 3.1.2(Inside Width), 3.1.3(Inside Height), 3.1.4(Internal Doors))	-	5000	-
3.2(Dimensions of the Evaporator Space)	-	5000	-

-
Included w.e.f 19.06.2025

IS 11328 (2022)

Self-contained Automatic Ice Makers Specification (First Revision)

Self-Contained Automatic Ice Makers

23900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Construction)	-	2000	-
Cl-5.2(Water Condensation)	-	2000	-
Cl-5.3(Safety Features in Design)	-	2000	-
Cl-5.4(Control of Operation)	-	2000	-
Cl-5.5(Location of the Components)	-	2000	-
Cl-6.1(Motors)	-	2000	-
Cl-6.3(Motor Starters, Relays, Thermostat, Controls, etc)	-	2000	-
Cl-6.4(Wiring)	-	2000	-
Cl-6.5(Electrical Accessories)	-	2000	-
Cl-6.6(Earth Connection)	-	2000	-
Cl-7.1(General Requirements for Tests)	-	2000	-
Cl-7.2(Ice Weighing Instruments)	-	2000	-
Cl-7.3(Type Tests)	-	5000	-
Cl-7.4(Routine Tests)	-	3000	-
Cl-7.5(Acceptance Tests)	-	5000	-
Cl-7.6(Test Procedure)	-	5000	-
Cl-8(Marking)	-	500	-

-
Included w.e.f 19.06.2025

Bureau of Indian Standards

The National Standards Body of India

Samridhi Test House Pvt. Ltd.

KH.NO. 45/23/1 GROUND FLOOR, VILLAGE & POST OFFICE VILLAGE PRAHALADPUR, North Delhi, NEW DELHI, North West, Delhi, 110042

9870394724 info@samridhitesthouse.com

Scope List