BIS - LIMS (Laboratory Information Management System)

Samridhi Test House Pvt. Ltd.

KH.NO. 45/23/1 GROUND FLOOR, VILLAGE & POST OFFICE VILLAGE PRAHALADPUR, North Delhi, NEW DELHI, North West, Delhi, 110042

9870394724 info@samridhitesthouse.com

Scope List

Reset

101 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

Unplasticized PVC Pipes for Potable Water Supplies - Specification

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	1000	-
10.1(Surface Finish)	-	1000	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	1000	-
10.7(Sulphated Ash Content)	-	2000	-
5(CLASSIFICATION OF PIPES)	-	1000	-
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	1000	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	1000	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	1000	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	1000	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	1000	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	1000	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	1000	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	1000	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	1000	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	1000	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	1000	-
7.2.1(DIMENSIONS-Socket)	-	1000	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	1000	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	1000	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	1000	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	1000	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	1000	-
8(SEALING RINGS)	-	1000	-
9.1(PIPE ENDS)	-	1000	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	1000	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	1000	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	2000	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	2000	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	2000	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	2000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	20000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	20000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	20000	-
11.2(Resistance to External Blows at 0°C)	-	2000	-
10.3(Effect on Water Test)	-	0	Excluding Cl. 10.3 of IS 4985: 2021 Effect on Water
6.1.2(PVC Resin)	-	5000	-
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	1000	-
7.1.4(Length)	-	1000	-
6.1.1(VCM Content)	-	0	Excluding 6.1.1 of IS 4985: 2021 Composition (VCM Content)
7.2.1.2b(Maximum inner diameter of groove)	-	1000	-
13.1(Marking)	-	500	-
10.1(Colour)	-	0	-
10.1(Surface Finish)	-	0	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	0	-
10.7(Sulphated Ash Content)	-	0	-
5(CLASSIFICATION OF PIPES)	-	0	-
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	0	-
7.2.1(DIMENSIONS-Socket)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	-
6.1.2(PVC Resin)	-	0	-
9.1(PIPE ENDS)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	0	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	0	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	0	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	0	-
11.2(Resistance to External Blows at 0°C)	-	0	-
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	0	-
7.1.4(Length)	-	0	-
6.1.1(VCM Content)	-	0	-
7.2.1.2b(Maximum inner diameter of groove)	-	0	-
13.1(Marking)	-	0	-
8(SEALING RINGS)	-	0	-
cL-13.1.1(Marking)	-	0	-
Cl-13.1.2(Marking)	-	0	-
7.2.1.2b(Maximum inner diameter of groove)	-	0	-
10.1(Surface Finish)	-	0	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	0	-
10.7(Sulphated Ash Content)	-	0	-
5(CLASSIFICATION OF PIPES)	-	0	-
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	0	-
7.2.1(DIMENSIONS-Socket)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	-
6.1.2(PVC Resin)	-	0	-
9.1(PIPE ENDS)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	0	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	0	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	0	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	0	-
11.2(Resistance to External Blows at 0°C)	-	0	-
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	0	-
7.1.4(Length)	-	0	-
13.1(Marking)	-	0	-
8(SEALING RINGS)	-	0	-
cL-13.1.1(Marking)	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	-
Cl-13.1.2(Marking)	-	0	-
10.3(Effect on Water Test)	-	0	-
10.1(Colour)	-	0	-
10.1(Colour)	-	0	-
10.1(Surface Finish)	-	0	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	0	-
10.7(Sulphated Ash Content)	-	0	-
5(CLASSIFICATION OF PIPES)	-	0	-
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	0	-
7.2.1(DIMENSIONS-Socket)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	-
8(SEALING RINGS)	-	0	-
9.1(PIPE ENDS)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	0	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	0	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	0	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	0	-
11.2(Resistance to External Blows at 0°C)	-	0	-
6.1.2(PVC Resin)	-	0	-
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	0	-
7.1.4(Length)	-	0	-
7.2.1.2b(Maximum inner diameter of groove)	-	0	-
13.1(Marking)	-	0	-
cL-13.1.1(Marking)	-	0	-
Cl-13.1.2(Marking)	-	0	-
Cl-10.3 (ii)(Effect on Lead (third extraction))	-	0	-
Cl-10.3 (iii)(Effect on Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	-
Cl-10.3 (iv)(Effect on Cadmium)	-	0	-
Cl-10.3 (v)(Effect on Mercury)	-	0	-
Cl-10.3 (vi)(Other toxic substances such as ‘di-n-octyl-tin- mass) s-s bis iso-octyl mercapto acetate’ and ‘butyl stearate)	-	0	-
10.3(Effect on Water Test)	-	0	-
6.1.1(VCM Content)	-	0	-
Cl-10.3 (i)(Effect on Lead (first extraction))	-	0	-

-
Included w.e.f 29.10.2025 Exclusion: Cl 6.1.2 (PVC Resin), Cl 6.1.1 (VCM Content)

IS 9995 (1981)

Specification for visor for non-metal police and firemen's helmets

Specification for Visor for Non-Metal Police and Firemen’s Helmets

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Visor Screen)	-	9600	Except Appendix A-1.4 Compressive Strength, Appendix A-1.5 Impact Strength, Appendix A-1.8 Rockwell Hardness test facility not available.
4(Construction)	-	500	-
5(Workmanship and Finish)	-	500	-
6(Mass)	-	500	-
8(Marking)	-	500	-

-
Included w.e.f 17.06.2025 Exclusion: Appendix A-1.4 Compressive Strength, Appendix A-1.5 Impact Strength, Appendix A-1.8 Rockwell Hardness

IS 2745 (1983)

Specification for non - Metal helmet for firemen and civil defence personnel (Second Revision)

16700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(Shell, Protective padding, Retention System & Neck protector)	-	4000	-
Cl 4.1(Size Of Helmet)	-	900	-
Cl 5( Shell, Protective Padding, Brim, Head band, Chin Strap, Cradle, Neck Protector & Visor)	-	14000	Appendix A-1.4 of IS 9995:1981 Compressive Strength, Appendix A-1.5 of IS 9995:1981 Impact Strength, Appendix A-1.8 of IS 9995:1981 Rockwell Hardness test facility not available.
Cl 6(Workmanship & Finish)	-	600	-
Cl 7(Mass)	-	500	-
Cl 9(Shock absorption test, Penitration resistance, Strength of Retention system, Electrical resistance, Water Absorption & Flammability resistance)	-	8000	-
Cl 9(Shock absorption test, Penitration resistance, Strength of Retention system, Electrical resistance, Water Absorption & Flammability resistance)	-	8000	-
Cl 7(Mass)	-	500	-
Cl 6(Workmanship & Finish)	-	600	-
Cl 5( Shell, Protective Padding, Brim, Head band, Chin Strap, Cradle, Neck Protector & Visor)	-	14000	-
Cl 4.1(Size Of Helmet)	-	900	-
Cl 3(Shell, Protective padding, Retention System & Neck protector)	-	4000	-

-
Included w.e.f.27.06.2025 Exclusion Excluding 5.3.5 visior.

IS 9562 (1980)

Specification for non - Metal helmet for police force

Specification for non metal helmet for police force

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(Shell, Protective padding & Retention System)	-	3000	-
Cl 4.1(Size Of Helmet)	-	1000	-
Cl 5( Shell, Protective Padding, Brim, Head band, Chin Strap, Cradle, Neck Protector & Visor)	-	14000	Excluding Appendix A-1.8 of IS 9995:1981 Rockwell Hardness, Appendix A-1.5 of IS 9995:1981 Impact Strength, Appendix A-1.4 of IS 9995:1981 Compressive Strength this test facility not available
Cl 6(Workmanship & Finish)	-	600	-
Cl 7(Mass)	-	500	-
Cl 9(Shock absorption test, Penitration resistance, Strength of Retention system, Rigidity test, Water Absorption, Flammability resistance & Firing Test)	-	8000	Excluding Cl. 9.7 Firing Test facility not available.
Cl 9(Shock absorption test, Penitration resistance, Strength of Retention system, Rigidity test, Water Absorption, Flammability resistance & Firing Test)	-	8000	Excluding Cl. 9.7 Firing Test facility not available.
Cl 7(Mass)	-	500	-
Cl 6(Workmanship & Finish)	-	600	-
Cl 5( Shell, Protective Padding, Brim, Head band, Chin Strap, Cradle, Neck Protector & Visor)	-	14000	Excluding Appendix A-1.8 of IS 9995:1981 Rockwell Hardness, Appendix A-1.5 of IS 9995:1981 Impact Strength, Appendix A-1.4 of IS 9995:1981 Compressive Strength this test facility not available
Cl 4.1(Size Of Helmet)	-	900	-
Cl 3(Shell, Protective padding & Retention System)	-	3000	-
Cl 3(Shell, Protective padding & Retention System)	-	0	-
Cl 4.1(Size Of Helmet)	-	0	-
Cl 5( Shell, Protective Padding, Brim, Head band, Chin Strap, Cradle, Neck Protector & Visor)	-	0	-
Cl 6(Workmanship & Finish)	-	0	-
Cl 7(Mass)	-	0	-
Cl 9(Shock absorption test, Penitration resistance, Strength of Retention system, Rigidity test, Water Absorption, Flammability resistance & Firing Test)	-	0	-
Cl 9(Shock absorption test, Penitration resistance, Strength of Retention system, Rigidity test, Water Absorption, Flammability resistance & Firing Test)	-	0	-
Cl 7(Mass)	-	0	-
Cl 6(Workmanship & Finish)	-	0	-
Cl 5( Shell, Protective Padding, Brim, Head band, Chin Strap, Cradle, Neck Protector & Visor)	-	0	-
Cl 4.1(Size Of Helmet)	-	0	-
Cl 3(Shell, Protective padding & Retention System)	-	0	-

-
Included w.e.f 17.06.2025 Exclusion: Cl. 9.7 Firing Test, Appendix A-1.4 Compressive Strength, Appendix A-1.5 Impact Strength, Appendix A-1.8 Rockwell Hardness

IS 17681 (2022)

Specification for Bottled water dispensers

210000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Construction)	-	6300	-
4.1(General Design)	-	700	-
4.2(Materials)	-	700	-
4.3(Finish)	-	700	-
4.4(Thermal Insulation)	-	700	-
4.5(Hardware)	-	700	-
4.6(Disposal of Waste Water)	-	700	-
4.7(Hot Water Tank)	-	700	-
4.8(Hermetically Sealed Compressor)	-	700	-
4.9(Protective Guards)	-	700	-
5(Refrigeration System)	-	1000	-
5.1(Pipes and Connections/Fitting)	-	500	-
5.2(Control of Operation)	-	500	-
6.1(General)	-	30700	-
6.1(Protection against electric shock (Cl. 8 of IS 302-2-24))	-	2000	-
6.1(Power Input & Current (Cl. 10 of IS 302-2-24))	-	3000	-
6.1(Temperature Rise/ Heating (Cl. 11 of IS 302-2-24))	-	5000	-
6.1("Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength (Cl. 13 of IS 302-2-24)")	-	6000	-
6.1("Moisture Resistance (Cl. 15 of IS 302-2-24)")	-	3500	-
6.1("Insulation resistance and electric strength (After humidity treatment) (Cl. 16 of IS 302-2-24)")	-	4000	-
6.1("Provision For Earthing (Cl. 27 of IS 302-2-24)")	-	4000	-
6.2(Electrical Accessories)	-	1500	-
6.3(Salt Mist Test)	-	20000	-
7(Sound pressure level)	-	14300	-
10.1(Cooling Capacity Test)	-	22000	-
10.2(Maximum Operating Condition Test (Environmental))	-	15000	-
10.3(Maximum Operating Condition Test (Voltage))	-	15000	-
10.4(Heating Capacity Test)	-	15000	-
10.5(Annual Energy Consumption Test)	-	30000	-
10.6(Freeze-up Test)	-	20000	-
10.7(Door Opening and Closing Test)	-	8000	-
10.8(Door Seal Test)	-	2000	-
10.9(Pull-down Test)	-	8000	-
11(Marking and instruction)	-	1000	-
6.1("Screws & Connections (Cl. 28 of IS 302-2-24)")	-	3000	-

-
Included w.e.f 21.05.2025

IS 17550 : PART 1 (2021)

HOUSEHOLD REFRIGERATING APPLIANCES CHARACTERISTICS AND TEST METHODS Part 1 General Requirements

200000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
"Cl. No. 9 "(Testing The Air Tightness Of Door Or Lid Seal(S))	-	6600	-
"Cl. No.10 "(Testing The Opening Force Of Door(S) Or Lid(S))	-	9500	-
"Cl. No.11 "(Testing The Durability Of Hinges And Handles Of Door(S) And Lid(S))	-	38000	-
"Cl. No.12 "(Testing The Mechanical Strength Of Shelves And Similar Components)	-	12000	-
"Cl. No.14 "(Ice-Making Test (If Applicable))	-	19000	-
"Cl. No.15 "(Test For Absence Of Odour And Taste)	-	42000	-
"Cl. No.16 "(Safety Requirements)	-	42400	-
"Cl. No. 9 "(Testing The Air Tightness Of Door Or Lid Seal(S))	-	0	Repeat Test
"Cl. No.10 "(Testing The Opening Force Of Door(S) Or Lid(S))	-	0	Repeat Test
"Cl. No.11 "(Testing The Durability Of Hinges And Handles Of Door(S) And Lid(S))	-	0	Repeat Test
"Cl. No.12 "(Testing The Mechanical Strength Of Shelves And Similar Components)	-	0	Repeat Test
"Cl. No.14 "(Ice-Making Test (If Applicable))	-	0	Repeat Test
"Cl. No.15 "(Test For Absence Of Odour And Taste)	-	0	Repeat Test
"Cl. No.16(a) "(Protection against acess to live parts)	-	5000	-
"Cl. No.16(b) "(Power input and current)	-	9000	-
"Cl. No.16(c) "(Heating)	-	7000	-
"Cl. No.16(d) "(Leakage current and electric strength at operating temperature)	-	5700	-
"Cl. No.16(e) "(Moisture resistance)	-	10000	-
"Cl. No.16(f) "(Leakage current and electric strength)	-	5700	-
"Cl. No.20.3(a) "("Production Routine Test a)Leakage current test ")	-	2800	-
"Cl. No.20.3(b) "(b) Earth continuity tesT)	-	2800	-
"Cl. No.20.3(c) "(c) Electric strength)	-	2800	-
"Cl. No.8.11 "(Thermostat function test)	-	500	-
"Cl. No.5 "(Markings)	-	2400	-
4(Classification)	-	500	-
5(Marking)	-	0	Repeat Test
6.2(Determination of Linear Dimensions)	-	1000	-
7(Instructions)	-	500	-
8.2(Material and Finishes)	-	500	-
8.3(Thermal Insulation and Air Tightness)	-	500	-
8.4(Doors, Lids and Fittings)	-	500	-
8.5(Shelves and Containers)	-	500	-
8.6(Disposal of Defrost Water)	-	500	-
8.7(Refrigerating System)	-	500	-
8.8(Supply Cord)	-	500	-
8.9(Compressor)	-	500	-
8.10(Temperature Sensing Controls (Thermostat))	-	500	-
8.11(Temperature Sensing Controls (Thermostat) Setting)	-	0	Repeat Test
9(Testing the Air tightness of door or lid seal(s) before water vapour condensation test)	-	0	Repeat Test
9(Testing the Air tightness of door or lid seal(s) after water vapour condensation test)	-	0	Repeat Test
10(Testing the Opening force of door(s) or lid(s))	-	0	Repeat Test
11(Testing the Durability of hinges and handles of door(s) and lid(s))	-	0	Repeat Test
12(Testing the Mechanical strength of shelves and similar components)	-	0	Repeat Test
13(Water-vapour condensation test)	-	6000	-
14(Ice-making test (if applicable))	-	0	Repeat Test
15(Test for absence of odour and taste)	-	0	Repeat Test
16(a)(Protection against access to live parts)	-	0	Repeated Test
16(b)(Power input and current)	-	0	Repeated Test
16 (c(Heating)	-	0	Repeated Test
16(d)(Leakage current and electric strength at operating temperature)	-	0	Repeated Test
16(e)(Moisture resistance)	-	0	Repeated Test
16(f)(Leakage current and electric strength (high voltage after humidity))	-	0	Repeated Test
17(Packing)	-	1000	-
18(Designation)	-	1000	-
19(Instructions for Use and Maintenance)	-	4700	-
20.3 (a)(Leakage Current Test)	-	0	Repeat Test
20.3 (b)(Earth Continuity Test)	-	0	Repeat Test
20.3 (c(Electric Strength Test)	-	0	Repeat Test

-
Included w.e.f 21.05.2025

IS 2925 (1984)

Specification for industrial safety helmets (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Shell)	-	500	-
3.2(Harness)	-	200	-
3.3(Metal Parts)	-	2000	-
4.1(Sizes)	-	500	-
5.1(Shell)	-	100	-
5.2(Harness)	-	1000	-
5.3(Chin Strap or Nape Strap)	-	2000	-
5.4(Lamp Bracket)	-	1000	-
5.5(Cable Clip)	-	1000	-
6.1(Workmanship & Finish)	-	100	-
7.1(Mass)	-	500	-
8.1(Shock Absorption Resistance)	-	1000	-
8.2(Penetration Resistance)	-	1000	-
8.3(Flamability Resistance)	-	1000	-
8.4(Electrical Resistance)	-	1000	-
8.5(Water Absorption)	-	1000	-
8.6(Heat Resistance)	-	1000	-
3.1(Shell)	-	0	Repeated Test
3.2(Harness)	-	0	Repeated Test
3.3(Metal Parts)	-	0	Repeated Test
4.1(Sizes)	-	0	Repeated Test
5.1(Shell)	-	0	Repeated Test
5.2(Harness)	-	0	Repeated Test
5.3(Chin Strap or Nape Strap)	-	0	Repeated Test
5.4(Lamp Bracket)	-	0	Repeated Test
5.5(Cable Clip)	-	0	Repeated Test
6.1(Workmanship & Finish)	-	0	Repeated Test
7.1(Mass)	-	0	Repeated Test
8.1(Shock Absorption Resistance)	-	0	Repeated Test
8.2(Penetration Resistance)	-	0	Repeated Test
8.3(Flamability Resistance)	-	0	Repeated Test
8.4(Electrical Resistance)	-	0	Repeated Test
8.5(Water Absorption)	-	0	Repeated Test
8.6(Heat Resistance)	-	0	Repeated Test
5.2.1(Head Band)	-	1000	-
5.3.1(Chin Strap)	-	1000	-
5.3.2(Nape Strap)	-	1000	-

-
-

IS 17550 : PART 3 (2021)

Household Refrigerating Appliance- Characteristics and test methods Part 3 Energy Consumption and volume

105000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
"Cl. No. 6 "("DETERMINATION OF ENERGY CONSUMPTION")	-	7000	-
"Cl. No.4.8 & Annex H "(Determination Of Volume)	-	14000	-
"Cl. No. 6 "("DETERMINATION OF ENERGY CONSUMPTION")	-	0	Repeat Test
"Cl. No. 6 "("DETERMINATION OF ENERGY CONSUMPTION")	-	0	Repeat Test
4.3(Defrost and Recovery Energy and temperature change)	-	14000	-
4.4(Defrost Frequency)	-	14000	-
4.5(Number of Test Points and Interpolations)	-	14000	-
4.6(Load Processing Efficiency)	-	14000	-
4.7(Specified Auxiliaries)	-	14000	-
4.8(Volumn Determination)	-	0	Repeat Test
6(Determination of Energy Consumption)	-	0	Repeat Test
Annex B(Determination of Steady state Power & Temperature)	-	14000	-
Annex C(Defrost and Recovery Energy and temperature change)	-	14000	-
Annex D(Defrost Interval)	-	14000	-
Annex E(Interpolation of Results)	-	14000	-
Annex F(Energy Consumption of specified auxiliaries)	-	14000	-
Annex G(Determination of Load Processing Efficiency)	-	14000	-
Annex H(Determination of Volume)	-	14000	-
"Cl. No.4.8 & Annex H "(Determination Of Volume)	-	0	Repeat Test
4.2(Steady State Power Consumption)	-	14000	-

-
Included w.e.f 21.05.2025

IS 17550 : PART 2 (2021)

Household Refrigerating Appliance- Characteristics and test methods Part 2 Performance requirements

300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No. 6(Storage Test)	-	10000	-
Cl. No. 7(Cooling Capacity Test)	-	45000	-
Cl. No. 8(Freezing Capacity Test)	-	45000	-
Cl. No. 9("Automatic Ice-Making Capacity Test")	-	45000	-
"Cl. No.4.6 & Annex A"(PULL-DOWN TEST)	-	35000	-
Cl. No.4.6(b) & Annex B("Wine Storage Appliances And Compartments; Storage Test")	-	34000	-
Cl. No.4.6(C) & AnnexC("Temperature Rise Test ")	-	45000	-
Cl. No.4.6(d) & Annex D("Water Vapour Condensation Test ")	-	40000	-
Cl. No.4.6(d) & Annex D("Water Vapour Condensation Test ")	-	0	Repeat Test
Cl. No. 6(Storage Test)	-	0	Repeat Test
Cl. No. 8(Freezing Capacity Test)	-	0	Repeat Test
Cl. No. 9("Automatic Ice-Making Capacity Test")	-	0	Repeat Test
"Cl. No.4.6 & Annex A"(PULL-DOWN TEST)	-	0	Repeat Test
Cl. No.4.6(b) & Annex B("Wine Storage Appliances And Compartments; Storage Test")	-	0	Repeat Test
Cl. No.4.6(C) & AnnexC("Temperature Rise Test ")	-	0	Repeat Test
Cl. No.4.6(d) & Annex D("Water Vapour Condensation Test ")	-	0	Repeat Test
4.2(Storage test)	-	10000	-
4.3(Cooling capacity test)	-	45000	-
4.5(Automatic ice-making capacity test)	-	45000	-
4.6(Other Tests)	-	154000	-
6(Storage test)	-	0	Repeat Test
7(Cooling capacity test)	-	0	Repeat Test
8(Freezing capacity test)	-	0	Repeat Test
9(Automatic ice-making capacity test)	-	0	Repeat Test
Annex A(Pull Down test)	-	35000	-
Annex B(Storage test of wine storage appliances and compartments)	-	34000	-
Annex C(Temperature Rise Test)	-	45000	-
Annex D(Water Vapour Condensation Test)	-	40000	-
4.4(Freezing Capacity Test)	-	45000	-
5(General Test Conditions)	-	1000	-

-
Included w.e.f 21.05.2025

100

IS 302 : Part 2 : Sec 7 (2024)

Safety of Household And Similar Electrical Appliances Part 2 Particular Requirements Section 7: Domestic Electric Clothes Washing Machines

46000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(GENERAL REQUIREMENT)	-	200	-
6(CLASSIFICATION)	-	200	-
7(MARKING AND INSTRUCTIONS)	-	500	-
8(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	1000	-
10(POWER INPUT AND CURRENT)	-	1000	-
11(HEATING)	-	1500	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	1000	-
14(TRANSIENT OVERVOLTAGES)	-	1500	-
15(MOISTURE RESISTANCE)	-	3000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	10000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	1000	-
21(MECHANICAL STRENGTH)	-	1000	-
22(CONSTRUCTION)	-	1500	-
23(INTERNAL WIRING)	-	1500	-
24(COMPONENTS)	-	0	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	1000	-
27(PROVISION FOR EARTHING)	-	1000	-
28(SCREWS AND CONNECTIONS)	-	1000	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
30(RESISTANCE TO HEAT AND FIRE)	-	1500	-
31(RESISTANCE TO RUSTING)	-	1600	-
19.13(ABNORMAL OPERATION)	-	5000	-
19.101(Abnormal Operation)	-	5000	-
19.102(Abnormal Operation)	-	5000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	1000	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	2000	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	0	Repeat Test
18(ENDURANCE)	-	2000	-
19(ABNORMAL OPERATION)	-	16000	-
19.11.4.1(Electrostatic discharges)	-	10000	-
19.11.4.2(Radiated fields)	-	10000	-
19.11.4.3(Fast transient bursts)	-	10000	-
19.11.4.4(Surge immunity test)	-	10000	-
19.11.4.7(Harmonics)	-	10000	-
19.11.4.5(Immunity to conducted discharges)	-	10000	-

-
Included w.e.f 21.05.2025 Exclusion: Cl 19.11.4 (EMI/EMC tests)

101

IS 9973 (1981)

Specification for visor for scooter helmets

6700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Impact resistance)	-	300	-
5.2(Penetration resistance)	-	400	-
5.3(Flammability)	-	600	-
5.4.1(Distortion)	-	200	-
5.4.2(Spherical&Cylindral error)	-	900	-
5.4.3(Prismatic Error)	-	900	-
5.4.4(Diffuse transmittance)	-	800	-
5.4.5(Light transmission)	-	800	-
5.5(Field of Vision)	-	800	-
7.0(Mass)	-	300	-
5.1(Impact resistance)	-	0	Repeated Test
5.2(Penetration resistance)	-	0	Repeated Test
5.3(Flammability)	-	0	Repeated Test
5.4.1(Distortion)	-	0	Repeated Test
5.4.2(Spherical&Cylindral error)	-	0	Repeated Test
5.4.3(Prismatic Error)	-	0	Repeated Test
5.4.4(Diffuse transmittance)	-	0	Repeated Test
5.4.5(Light transmission)	-	0	Repeated Test
5.5(Field of Vision)	-	0	Repeated Test
7.1(Mass)	-	0	Repeated Test
3(Materials)	-	200	-
4(Design)	-	200	-
6.1(Workmanship and Finish)	-	100	-
5.2.2(Cradle)	-	0	This clause Number is not mentioned in the standard.

-
-

Bureau of Indian Standards

The National Standards Body of India

Samridhi Test House Pvt. Ltd.

KH.NO. 45/23/1 GROUND FLOOR, VILLAGE & POST OFFICE VILLAGE PRAHALADPUR, North Delhi, NEW DELHI, North West, Delhi, 110042

9870394724 info@samridhitesthouse.com

Scope List