BIS - LIMS (Laboratory Information Management System)

Bharat Test House Pvt Ltd 1474 Haryana

1474, HSIIDC Rai Industrial Estate, SONIPAT, Sonipat, Haryana, 131029

9310314585 bthrai@bharattesthouse.com

Scope List

Reset

145 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 14286 : Part 1 (2023)

Terrestrial Photovoltaic PV Modules Design Qualification and Type Approval Part 1: Test Requirements (Third Revision)

Terrestrial Photovoltaic PV Modules

1502500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Visual inspection (MQT 01))	-	7000	-
4.2(Maximum power determination (MQT 02))	-	7000	-
4.3(Insulation test (MQT 03))	-	20000	-
4.4(Measurement of temperature coefficients (MQT 04))	-	110000	-
4.5(Placeholder section, formerly NMOT)	-	0	-
4.6(Performance at STC (MQT 06.1))	-	7500	-
4.7(Performance at low irradiance (MQT 07))	-	10000	-
4.8(Outdoor exposure test (MQT 08))	-	50000	-
4.9(Hot-spot endurance test (MQT 09))	-	125000	-
4.10(UV preconditioning test (MQT 10))	-	125000	-
4.11(Thermal cycling test (MQT 11))	-	160000	-
4.12(2 Humidity-freeze test (MQT 12))	-	80000	-
4.13(Damp heat test (MQT 13))	-	160000	-
4.14(Robustness of terminations (MQT 14))	-	15000	-
4.15(5 Wet leakage current test (MQT 15))	-	25000	-
4.16(Static mechanical load test (MQT 16))	-	50000	-
4.17(Hail test (MQT 17))	-	50000	-
4.18(Bypass diode testing (MQT 18))	-	75000	-
4.19(Stabilization (MQT 19))	-	95000	-
4.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	95000	-
4.21(Potential induced degradation test (MQT 21))	-	175000	-
4.22(Bending test (MQT 22))	-	60000	-

Complete

19 Mar, 2026

-
Included w.e.f 05.03.2025

IS 1258 (2024)

Bayonet lampholders (Fifth Revision)

Bayonet lampholders

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General requirements)	-	0	-
6(Standard ratings)	-	50	-
7(Classification)	-	50	-
8(Marking)	-	100	-
9(Dimensions)	-	200	-
10(Protection against electric shock)	-	750	-
11(Terminals)	-	500	-
12(Provision for earthing)	-	750	-
13(Construction)	-	500	-
14(Switched lampholders)	-	1000	-
15(Moisture resistance, insulation resistance and electrical strength)	-	1500	-
16(Mechanical strength)	-	1250	-
17(Screws, current-carrying parts and connections)	-	750	-
18(Creepage distances and clearances)	-	600	-
19(General resistance to heat)	-	1250	-
20(Resistance to heat, fire and tracking)	-	2250	-
21(Resistance to excessive residual stresses (season cracking) and to rusting)	-	3000	-
Annex A(Season cracking/corrosion test)	-	500	-
12.4(Thermal tests)	-	750	-
9.1(Lampholder dimensions)	-	200	-
11.2(Terminals)	-	500	-
12.3(Provision for earthing)	-	750	-
13.1(Construction)	-	500	-
13.8(Construction)	-	500	-
14.4(Switched lampholders)	-	1000	-
15.1(Moisture resistance, insulation resistance and electrical strength)	-	1500	-
16.7(Mechanical strength)	-	1250	-
16.8(Mechanical strength)	-	1250	-
21.2(Resistance to excessive residual stresses (season cracking) and to rusting)	-	3000	-
4(General requirements)	-	0	-
6(Standard ratings)	-	0	-
7(Classification)	-	0	-
8(Marking)	-	0	-
9(Dimensions)	-	0	-
10(Protection against electric shock)	-	0	-
11(Terminals)	-	0	-
12(Provision for earthing)	-	0	-
13(Construction)	-	0	-
14(Switched lampholders)	-	0	-
15(Moisture resistance, insulation resistance and electrical strength)	-	0	-
16(Mechanical strength)	-	0	-
17(Screws, current-carrying parts and connections)	-	0	-
18(Creepage distances and clearances)	-	0	-
19(General resistance to heat)	-	0	-
20(Resistance to heat, fire and tracking)	-	0	-
21(Resistance to excessive residual stresses (season cracking) and to rusting)	-	0	-
Annex A(Season cracking/corrosion test)	-	0	-
12.4(Thermal tests)	-	0	-
9.1(Lampholder dimensions)	-	0	-
11.2(Terminals)	-	0	-
12.3(Provision for earthing)	-	0	-
13.1(Construction)	-	0	-
13.8(Construction)	-	0	-
14.4(Switched lampholders)	-	0	-
15.1(Moisture resistance, insulation resistance and electrical strength)	-	0	-
16.7(Mechanical strength)	-	0	-
16.8(Mechanical strength)	-	0	-
21.2(Resistance to excessive residual stresses (season cracking) and to rusting)	-	0	-

Complete

19 Mar, 2026

-
Included.w.e.f.27.01.2025

IS 9815 : Part 1 (1994)

Servo - Motor operated automatic line voltage correctors: Part 1 correctors for single - Phase applications - Specification (Second Revision)

Servo - Motor operated automatic line voltage correctors

95000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4(Service Conditions)	-	0	-
Clause 5(Rating)	-	0	-
Clause 6(Construction)	-	0	-
Clause 7.1(Insulation)	-	7000	-
Clause 7.2(Provision for Earthing)	-	7000	-
Clause 7.3(Leakage Current Under Normal Operating Conditions)	-	7000	-
Clause 8.1(Temperature-rise )	-	17000	-
Clause 9(Performance Requirement)	-	3000	-
Clause 10(Marking)	-	0	-
Clause 11.1(Type Test)	-	95000	-
Clause 11.2(Acceptance Tests)	-	25500	-
Clause 11.3(Routine Tests)	-	20500	-
Clause 11.4(Insulation Resistance Test)	-	7000	-
Clause 11.5(High Voltage Test)	-	7000	-
Clause 11.6(Output Voltage Test)	-	3500	-
Clause 11.7(No-Load Current Test)	-	3500	-
Clause 11.8(No-Load Loss Test)	-	3500	-
Clause 11.9(Load Loss Test and Efficiency)	-	10000	-
Clause 11.10(Induced Voltage Test)	-	5000	-
Clause 11.11(Test for Continuous Operation)	-	15000	-
Clause 11.12(Temperature-Rise Test)	-	17000	-
Clause 11.13(Test for Rate of Correction)	-	3500	-
Clause 11.14(Locked Rotor Test For Servo-Motor)	-	9000	-
Clause 11.15(Damp Heat Test)	-	22000	-
Clause 4(Service Conditions)	-	0	-
Clause 5(Rating)	-	0	-
Clause 6(Construction)	-	0	-
Clause 7.1(Insulation)	-	0	-
Clause 7.2(Provision for Earthing)	-	0	-
Clause 7.3(Leakage Current Under Normal Operating Conditions)	-	0	-
Clause 8.1(Temperature-rise )	-	0	-
Clause 9(Performance Requirement)	-	0	-
Clause 10(Marking)	-	0	-
Clause 11.1(Type Test)	-	0	-
Clause 11.2(Acceptance Tests)	-	0	-
Clause 11.3(Routine Tests)	-	0	-
Clause 11.4(Insulation Resistance Test)	-	0	-
Clause 11.5(High Voltage Test)	-	0	-
Clause 11.6(Output Voltage Test)	-	0	-
Clause 11.7(No-Load Current Test)	-	0	-
Clause 11.8(No-Load Loss Test)	-	0	-
Clause 11.9(Load Loss Test and Efficiency)	-	0	-
Clause 11.10(Induced Voltage Test)	-	0	-
Clause 11.11(Test for Continuous Operation)	-	0	-
Clause 11.12(Temperature-Rise Test)	-	0	-
Clause 11.13(Test for Rate of Correction)	-	0	-
Clause 11.14(Locked Rotor Test For Servo-Motor)	-	0	-
Clause 11.15(Damp Heat Test)	-	0	-
Clause 4(Service Conditions)	-	0	-
Clause 5(Rating)	-	0	-
Clause 6(Construction)	-	0	-
Clause 7.1(Insulation)	-	0	-
Clause 7.2(Provision for Earthing)	-	0	-
Clause 7.3(Leakage Current Under Normal Operating Conditions)	-	0	-
Clause 8.1(Temperature-rise )	-	0	-
Clause 9(Performance Requirement)	-	0	-
Clause 10(Marking)	-	0	-
Clause 11.1(Type Test)	-	0	-
Clause 11.2(Acceptance Tests)	-	0	-
Clause 11.3(Routine Tests)	-	0	-
Clause 11.4(Insulation Resistance Test)	-	0	-
Clause 11.5(High Voltage Test)	-	0	-
Clause 11.6(Output Voltage Test)	-	0	-
Clause 11.7(No-Load Current Test)	-	0	-
Clause 11.8(No-Load Loss Test)	-	0	-
Clause 11.9(Load Loss Test and Efficiency)	-	0	-
Clause 11.10(Induced Voltage Test)	-	0	-
Clause 11.11(Test for Continuous Operation)	-	0	-
Clause 11.12(Temperature-Rise Test)	-	0	-
Clause 11.13(Test for Rate of Correction)	-	0	-
Clause 11.14(Locked Rotor Test For Servo-Motor)	-	0	-
Clause 11.15(Damp Heat Test)	-	0	-

Complete

19 Mar, 2026

-
Included .w.e.f.11.02.2025

IS 13730 : Part 0 : Sec 1 (2018)

Specifications for particular types of winding wires: Part 0 general requirements: Sec 1 enamelled round copper wire (Second Revision)

Enamelled Round Copper Wire

195000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions)	-	2500	-
4.1(Conductor diameter)	-	2500	-
4.2(Out of roundness of conductor)	-	2500	-
4.3(Minimum increase in diameter due to the insulation and the bonding layer)	-	2500	-
4.4(Maximum overall diameter)	-	2500	-
5(Electrical resistance)	-	5000	-
6(Elongation)	-	5000	-
7(Springiness)	-	5000	-
8.1(Mandrel winding test)	-	5000	-
8.2(Stretching test)	-	5000	-
8.3(Jerk test)	-	5000	-
8.4(Peel test)	-	5000	-
9(Heat shock)	-	10000	-
10(Cut-through)	-	7500	-
11(Resistance to abrasion)	-	7500	-
12(Resistance to solvents)	-	7500	-
13(Breakdown voltage)	-	9500	-
13.1(General)	-	0	-
13.2(Nominal conductor diameters up to and including 0,100 mm)	-	2500	-
13.3(Nominal conductor diameters over 0,100 mm up to and including 2,500 mm)	-	2500	-
13.4(Nominal conductor diameters over 2,500 mm)	-	2500	-
14(Continuity of insulation)	-	7500	-
15(Temperature index)	-	100000	-
16(Resistance to refrigerants)	-	2500	-
17(Solderability)	-	2500	-
18(Heat or solvent bonding)	-	2500	-
19(Dielectric dissipation factor)	-	2500	-
20(Resistance to transformer oil)	-	2500	-
21(Loss of mass)	-	2500	-
23(Pin hole test)	-	7500	-
30(Packaging)	-	500	-
4(Dimensions)	-	0	-
4.1(Conductor diameter)	-	0	-
4.2(Out of roundness of conductor)	-	0	-
4.3(Minimum increase in diameter due to the insulation and the bonding layer)	-	0	-
4.4(Maximum overall diameter)	-	0	-
5(Electrical resistance)	-	0	-
6(Elongation)	-	0	-
7(Springiness)	-	0	-
8.1(Mandrel winding test)	-	0	-
8.2(Stretching test)	-	0	-
8.3(Jerk test)	-	0	-
8.4(Peel test)	-	0	-
9(Heat shock)	-	0	-
10(Cut-through)	-	0	-
11(Resistance to abrasion)	-	0	-
12(Resistance to solvents)	-	0	-
13(Breakdown voltage)	-	0	-
13.1(General)	-	0	-
13.2(Nominal conductor diameters up to and including 0,100 mm)	-	0	-
13.3(Nominal conductor diameters over 0,100 mm up to and including 2,500 mm)	-	0	-
13.4(Nominal conductor diameters over 2,500 mm)	-	0	-
14(Continuity of insulation)	-	0	-
15(Temperature index)	-	0	-
16(Resistance to refrigerants)	-	0	-
17(Solderability)	-	0	-
18(Heat or solvent bonding)	-	0	-
19(Dielectric dissipation factor)	-	0	-
20(Resistance to transformer oil)	-	0	-
21(Loss of mass)	-	0	-
23(Pin hole test)	-	0	-
30(Packaging)	-	0	-

Complete

19 Mar, 2026

-
Included w.e.f 15.01.2025

IS 15884 (2024)

ALTERNATING CURRENT DIRECT CONNECTED STATIC PREPAYMENT METERS FOR ACTIVE ENERGY CLASS 1 AND 2 SPECIFICATION

Alternating Current Direct Connected Static Prepayment Meters for Active Energy of Class 1 and 2

253500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(GENERAL REQUIREMENTS)	-	0	-
5.2.1(Spring Hammer Test)	-	5833	-
5.2.2(Shock Test)	-	5833	-
5.2.3(Vibration Test)	-	5833	-
5.2.4(Test of Resistance to Heat and Fire)	-	5000	-
5.2.5(Tests of Protection against Penetration of Dust and Water)	-	7500	-
5.3.1(Dry Heat Test)	-	7500	-
5.3.2(Cold Test)	-	7500	-
5.3.3(Damp Heat Cyclic Test)	-	7500	-
5.4.1(Test of Power Consumption)	-	10000	-
5.4.2(Test of influence of voltage dips and interruptions)	-	10000	-
5.4.3(Test of Influence of Short-Time Overcurrent)	-	12500	-
5.4.4(Test of Influence of Self-Heating)	-	12500	-
5.4.5(Test of Influence of Heating)	-	10000	-
5.4.6.2(Impulse voltage test)	-	5833	-
5.4.6.3(a.c. voltage test)	-	5833	-
5.4.6.4(Insulation resistance test)	-	5833	-
5.5.2(Test of Immunity to Electrostatic Discharges)	-	50000	-
5.5.3(Test of Immunity to Electromagnetic HF Fields)	-	50000	-
5.5.4(Fast Transient Burst Test)	-	50000	-
5.5.5(Radio Interference Measurement)	-	50000	-
5.5.6(Surge Immunity Test)	-	50000	-
5.6.2(Test of Influence Quantities)	-	2500	-
5.6.3(Test of No-Load Condition)	-	2500	-
5.6.4(Test of Starting Condition)	-	2500	-
5.6.5(Test of Meter Constant)	-	2500	-
5.6.6(Interpretation of Test Results)	-	2500	-
5.7(Test of the Load Switch operation for payment function)	-	5000	-
5.8(Test of Charging Functions)	-	7500	-
5.9(Interruption and Restoration of the Load for Emergency Credit Facility (if applicable))	-	7500	-
5.10(Tests of the Load Switch operation at Different Voltages and Temperature)	-	15000	-
6(FUNCTIONAL REQUIREMENTS)	-	10000	-

Complete

19 Mar, 2026

-
Included w.e.f 02.01.2025

IS 14900 (2018)

Transparent float glass - Specification (First Revision)

Transparent Float Glass

575000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	3200	-
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	1900	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	2100	-
Cl.4.3.2.1(the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	2000	-
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	2000	-
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	2000	-
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	2000	-
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	3000	-
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	3500	-
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	0	-
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	2800	-
Cl.4.7 (Annexure F)(Material may be tested for bloom freedom as per Annex F whenever required by the purchaser.)	-	550000	-
4.3.1(Thickness)	-	2100	-
4.3.1(Thickness test)	-	2100	-
4.3.1(Thickness test)	-	2100	-
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	0	-
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	0	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	0	-
Cl.4.3.2.1(the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	0	-
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	0	-
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	0	-
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	0	-
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	0	-
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	0	-
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	0	-
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	0	-
Cl.4.7 (Annexure F)(Material may be tested for bloom freedom as per Annex F whenever required by the purchaser.)	-	0	-
4.3.1(Thickness)	-	0	-
4.3.1(Thickness test)	-	0	-
4.3.1(Thickness test)	-	0	-

Complete

19 Mar, 2026

-
Included w.e.f 17.03.2025

IS 17046 (2018)

Fibre Optic Cable for Cable TV Application

Fibre Optic Cable

125000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Design and construction of aerial metal free optical fibre cable)	-	0	-
3.2(Fibre used in the cable)	-	0	-
3.3(Self-supporting metal free aerial optical fibre cable)	-	0	-
3.4(Technical Requirements)	-	0	-
3.5(Mechanical Characteristics)	-	0	-
3.6(Environmental Characteristic of Fibre)	-	0	-
3.7(Optical Fibre Cable Construction Specifications)	-	0	-
3.8(Mechanical Characteristics and Tests on Optical Fibre Cable)	-	124900	-
4(Marking)	-	0	-
3.1(Design and construction of aerial metal free optical fibre cable)	-	0	-
3.2(Fibre used in the cable)	-	0	-
3.3(Self-supporting metal free aerial optical fibre cable)	-	0	-
3.4(Technical Requirements)	-	0	-
3.5(Mechanical Characteristics)	-	0	-
3.6(Environmental Characteristic of Fibre)	-	0	-
3.7(Optical Fibre Cable Construction Specifications)	-	0	-
3.8(Mechanical Characteristics and Tests on Optical Fibre Cable)	-	0	-
4(Marking)	-	0	-

Complete

19 Mar, 2026

-
Included.w.e.f.26.12.2024

IS 16614 : Part 1 (2018)

Double- Capped LED Linear Lamps Part1 Safety Specification

Double Capped LED Linear Lamps

67750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General)	-	0	-
5(Marking)	-	250	-
6.1(Interchangeability)	-	500	-
6.2(Mass)	-	250	-
6.3(Dimensions)	-	500	-
6.3(Dimensions)	-	500	-
6.4(Temperature)	-	5000	-
6.5("Safety Due to Wrong Starter-Lamp Combination")	-	0	-
7(PIN-SAFETY DURING INSERTION)	-	500	-
8("PROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE PARTS")	-	10000	-
9(Mechanical requirements for Caps)	-	6000	-
10(Cap Temperature Rise)	-	5000	-
11(Resistance to Heat)	-	1000	-
12(RESISTANCE TO FLAME AND IGNITION)	-	5000	-
13(FAULT CONDITIONS)	-	5000	-
14(CREEPAGE DISTANCES AND CLEARANCES)	-	1250	-
15("LAMPS WITH PROTECTION AGAINST DUST AND MOISTURE ")	-	20000	-

Complete

19 Mar, 2026

-
including w.e.f.10.10.2024

IS 302 : Part 2 : Sec 4 (1993)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 4 spin extractors

Spin extractors

38000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(GENERAL REQUIREMENTS)	-	0	-
4(GENERAL NOTES ON TESTS)	-	0	-
5(RATING)	-	200	-
6(CLASSIFICATION)	-	200	-
7(MARKING)	-	300	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	750	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	0	-
10(INPUT AND CURRENT)	-	1000	-
11(HEATING)	-	1500	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	2000	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	2500	-
15(MOISTURE RESISTANCE)	-	4500	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH (AFTER HUMIDITY TREATMENT))	-	2750	-
17(OVERLOAD PROTECTION)	-	1100	-
19(ABNORMAL OPERATION)	-	4700	-
20(STABILITY AND MECHANICAL HAZARDS)	-	1500	-
21(MECHANICAL STRENGTH)	-	2200	-
22(CONSTRUCTION)	-	4800	-
23(INTERNAL WIRING)	-	1000	-
24(COMPONENTS)	-	2000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	500	-
27(PROVISION FOR EARTHING)	-	500	-
28(SCREWS AND CONNECTIONS)	-	500	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	500	-
30(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	1000	-
31(RESISTANCE TO RUSTING)	-	1000	-
3(GENERAL REQUIREMENTS)	-	0	-
4(GENERAL NOTES ON TESTS)	-	0	-
5(RATING)	-	0	-
6(CLASSIFICATION)	-	0	-
7(MARKING)	-	0	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	0	-
10(INPUT AND CURRENT)	-	0	-
11(HEATING)	-	0	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	0	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	0	-
15(MOISTURE RESISTANCE)	-	0	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH (AFTER HUMIDITY TREATMENT))	-	0	-
17(OVERLOAD PROTECTION)	-	0	-
19(ABNORMAL OPERATION)	-	0	-
20(STABILITY AND MECHANICAL HAZARDS)	-	0	-
21(MECHANICAL STRENGTH)	-	0	-
22(CONSTRUCTION)	-	0	-
23(INTERNAL WIRING)	-	0	-
24(COMPONENTS)	-	0	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	0	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	0	-
27(PROVISION FOR EARTHING)	-	0	-
28(SCREWS AND CONNECTIONS)	-	0	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	0	-
30(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	0	-
31(RESISTANCE TO RUSTING)	-	0	-
3(GENERAL REQUIREMENTS)	-	0	-
4(GENERAL NOTES ON TESTS)	-	0	-
5(RATING)	-	0	-
6(CLASSIFICATION)	-	0	-
7(MARKING)	-	0	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	0	-
10(INPUT AND CURRENT)	-	0	-
11(HEATING)	-	0	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	0	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	0	-
15(MOISTURE RESISTANCE)	-	0	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH (AFTER HUMIDITY TREATMENT))	-	0	-
17(OVERLOAD PROTECTION)	-	0	-
19(ABNORMAL OPERATION)	-	4700	-
20(STABILITY AND MECHANICAL HAZARDS)	-	0	-
21(MECHANICAL STRENGTH)	-	0	-
22(CONSTRUCTION)	-	0	-
23(INTERNAL WIRING)	-	0	-
24(COMPONENTS)	-	0	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	0	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	0	-
27(PROVISION FOR EARTHING)	-	0	-
28(SCREWS AND CONNECTIONS)	-	0	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	0	-
30(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	0	-
31(RESISTANCE TO RUSTING)	-	0	-
19.11.4.1(Electrostatic discharges)	-	4700	-
19.11.4.2(Radiated fields)	-	4700	-
19.11.4.3(Fast transient bursts)	-	4700	-
19.11.4.4(Surge immunity test)	-	4700	-
19.11.4.5(Immunity to conducted discharges)	-	4700	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	4700	-
19.11.4.7(Harmonics)	-	4700	-

Complete

19 Mar, 2026

-
INCLUDING W.E.F 10.10.2024

IS 16170 : Part 3 (2022)

Photovoltaic (PV) Module Performance Testing and Energy Rating Part 3 Energy Rating of (PV) Modules (First Revision)

Photovoltaic (PV) Modules

350000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6(Module energy collection)	-	125000		-
7(Procedure for energy rating)	-	225000		-

Complete

19 Mar, 2026

-
including w.e.f 09.10.2024

IS 17980 (2022)

Maximum Power Point Tracking Efficiency of Grid Connected Photovoltaic Inverters (First Revision)

Grid Connected Photovoltaic Inverters

525000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (a)(Static MPPT efficiency)	-	250000		-
Cl-4.1 (b)(Dynamic MPPT efficiency)	-	275000		-

Complete

19 Mar, 2026

-
including w.e.f. 09.10.2024

IS 12943 (1990)

Brass glands for PVC cables - Specification

Brass glands for PVC cables

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General)	-	50	-
4.2(Materials)	-	50	-
4.3(Construction)	-	50	-
5.1.1(Acceptance Test)	-	0	-
5.2(Proof Torque Test)	-	7500	-
5.3(Tensile Test)	-	10000	-
5.4(Electrical Continuity Test)	-	6000	-

Complete

19 Mar, 2026

-
including w.e.f. 09.10.2024

IS 2083 (2024)

FLASHLIGHT- SPECIFICATION (Third Revision)

Flashlight

62500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Materials)	-	0	-
6(Dimensions)	-	250	-
8.1.1(Samples for Type Tests)	-	0	-
8.2(Acceptance Tests)	-	0	-
8.2(Acceptance Tests)	-	0	-
8.2.1(Sample for Acceptance Tests)	-	0	-
8.3(Routine Tests)	-	0	-
10(TEST FOR MECHANICAL ASSEMBLY)	-	1500	-
11(DROP TEST)	-	2500	-
12.1(Dry Heat Tests)	-	3000	-
12.2(Damp Heat (Accelerated) Test)	-	3000	-
12.3(Dry Cold Test (Optional))	-	5000	-
13(LIFE TEST FOR SWITCH)	-	5000	-
14.1(INSULATION RESISTANCE TEST)	-	1250	-
15(TEST FOR CONTACT RESISTANCE OF THE SWITCH)	-	1250	-
16(LIGHT DISTRIBUTION TEST)	-	6000	-
17(LUMEN DEPRECIATION TEST FOR LED FLASHLIGHT)	-	6000	-
18(CIRCUIT CURRENT OF LED FLASHLIGHT)	-	1250	-
21(TEST FOR INGRESS PROTECTION)	-	4500	-
24(THERMAL TEST)	-	5000	-

Complete

19 Mar, 2026

-
Included.w.e.f.11.09.2024 Exclusion CL 9 (TEST FOR FINISH)

IS 11360 (1985)

Specification for smoke detectors for use in automatic electrical fire alarm system

Smoke detectors for use in automatic electrical fire al

167500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(General Requirements)	-	0	-
4.1(Directional Dependence)	-	2500	-
4.2(Reproducibility and Optimal Sensitivity)	-	2500	-
4.3(Stability)	-	2500	-
4.4(Repeatability)	-	2500	-
4.5(Endurance)	-	35000	-
4.6(Supply Voltage Variation)	-	2000	-
4.7(Insulation Resistance)	-	3000	-
4.8(Vibration)	-	12500	-
4.9(Shock)	-	10000	-
4.10(High Temperature)	-	17500	-
4.11(Low Temperature)	-	20000	-
4.12(Humidity)	-	20000	-
4.13(Air Movement)	-	5000	-
4.14(Corrosion)	-	5000	-
4.15(Ambient Light)	-	2500	-
4.16(Transient)	-	5000	-
4.17(Dust)	-	10000	-
4.18(Fire Test)	-	10000	-
5(Marking)	-	0	-
3(General Requirements)	-	0	-
4.1(Directional Dependence)	-	0	-
4.2(Reproducibility and Optimal Sensitivity)	-	0	-
4.3(Stability)	-	0	-
4.4(Repeatability)	-	0	-
4.5(Endurance)	-	0	-
4.6(Supply Voltage Variation)	-	0	-
4.7(Insulation Resistance)	-	0	-
4.8(Vibration)	-	0	-
4.9(Shock)	-	0	-
4.10(High Temperature)	-	0	-
4.11(Low Temperature)	-	0	-
4.12(Humidity)	-	0	-
4.13(Air Movement)	-	0	-
4.14(Corrosion)	-	0	-
4.15(Ambient Light)	-	0	-
4.16(Transient)	-	0	-
4.17(Dust)	-	0	-
4.18(Fire Test)	-	0	-
5(Marking)	-	0	-

Complete

19 Mar, 2026

-
including w.e.f. 09.10.2024

IS 17017 : Part 1 (2018)

Electric Vehicle Conductive Charging System Part 1 General Requirements

Electric Vehicle Conductive Charging System

88000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(GENERAL REQUIREMENTS)	-	500	-
5(CLASSIFICATION)	-	500	-
6(CHARGING MODES AND FUNCTIONS)	-	500	-
7(COMMUNICATIONS)	-	500	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	15000	-
9(CONDUCTIVE ELECTRICAL INTERFACE REQUIREMENTS)	-	500	-
10(REQUIREMENTS FOR ADAPTORS)	-	500	-
11(CABLE ASSEMBLY REQUIREMENTS)	-	17500	-
12(EV SUPPLY EQUIPMENT CONSTRUCTIONAL REQUIREMENTS AND TESTS)	-	27500	-
13(OVERLOAD AND SHORT-CIRCUIT PROTECTION)	-	22500	-
14(AUTOMATIC RECLOSING OF PROTECTIVE DVICES)	-	500	-
15(EMERGENCY SWITCHING OR DISCONNECT ( OPTIONAL))	-	500	-
16(MARKING AND INSTRUCTIONS)	-	1500	-
4(GENERAL REQUIREMENTS)	-	0	-
5(CLASSIFICATION)	-	0	-
6(CHARGING MODES AND FUNCTIONS)	-	0	-
7(COMMUNICATIONS)	-	0	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	0	-
9(CONDUCTIVE ELECTRICAL INTERFACE REQUIREMENTS)	-	0	-
10(REQUIREMENTS FOR ADAPTORS)	-	0	-
11(CABLE ASSEMBLY REQUIREMENTS)	-	0	-
12(EV SUPPLY EQUIPMENT CONSTRUCTIONAL REQUIREMENTS AND TESTS)	-	0	-
13(OVERLOAD AND SHORT-CIRCUIT PROTECTION)	-	0	-
14(AUTOMATIC RECLOSING OF PROTECTIVE DVICES)	-	0	-
15(EMERGENCY SWITCHING OR DISCONNECT ( OPTIONAL))	-	0	-
16(MARKING AND INSTRUCTIONS)	-	0	-

Complete

19 Mar, 2026

-
including w.e.f 09.10.2024

IS/IEC 62368 : Part 1 (2018)

Audio / Video, Information and Communication Technology Equipment Part 1 Safety Requirements ( First Revision )

Audio / Video, Information and Communication Technology

95000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4, 4.1, 4.1.1, 4.1.2, 4.1.3, 4.1.4, 4.1.5, 4.1.6, 4.1.7, 4.1.8, 4.1.9,4.1.10, 4.1.11,4.1.12, 4.1.13, 4.1.14,4.1.15(General Requirements)	-	3000	-
Cl. 4.2, 4.2.1, 4.2.2, 4.2.3, 4.2.4(Energy source classifications)	-	3000	-
Cl. No. 4.3 ,4.4,4.5, 4.6,4.7,4.8,4.9,4.10 with all sub clauses(Protection against energy sources)	-	3000	-
Cl. No. 5,5.1,5.2,5.3,5.4,5.5,5.6,5.7,5.8 with all sub clauses(Electrically-caused injury)	-	5000	-
Cl No. 6,6.1,6.2,6.3,6.4,6.5,6.6 with all sub clause(Electrically-caused fire)	-	5000	-
Cl. 7, 7.1, 7.2, 7.3, 7.4, 7.5, 7.6(Injury caused by hazardous substances)	-	5000	-
Cl. 9, 9.1, 9.2, 9.2.1,9.2.2, 9.2.3, 9.3, 9.3.1, 9.3.2, 9.4, 9.5, 9.5.1, 9.5.2, 9.6, 9.6.1, 9.6.2, 9.6.3(Thermal burn injury)	-	5000	-
Cl. 8,8.1,8.2,8.3,8.4,8.5,8.6,8.7,8.8,8.9,8.10,8.11,8.12 with all sub clause(Mechanically-caused injury)	-	5000	-
Annex. B, B.1, B.1.1, B.1.2, B.1.3, B.1.4, B.1.5,B.2,B.2.1, B.2.2, B.2.3, B.2.4, B.2.5, B.2.6, B.2.6.1, B.2.6.2, B.2.6.3, B.2.7, B.3, B.3.1, B.3.2, B.3.3, B.3.4, B.3.5, B.3.6, B.3.7, B.3.8, B.4, B.4.1, B.4.2, B.4.3, B.4.3.1, B.4.3.2,B.4.4, B.4.4.1, B.4.4.(Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	5000	-
Annex. D, D.1, D.2, D.3(Test Generators)	-	5000	-
Annex E, E.1, E.2, E.3(Test conditions)	-	5000	-
Annex. F, F.1, F.2, F2.1, F.2.2,F2.3,F.3, F.3.1, F.3.2, F.3.2.1,F.3.2.2, F.3.3,F.3.3.1, F.3.3.2,F.3.3.3, F.3.3.4, F.3.3.5, F.3.3.6,F.3.3.7, F.3.3.8, F.3.4, F.3.5, F.3.5.1,F.3.5.2, F.3.5.3, F.3.5.4, F.3.5.5,F.3.5.6, F.3.5.7,F.3.6, F.3.6.1, F.3.6.1.1, F.3.6(Equipment markings, instructions, and instructional safeguards)	-	1000	-
Annex. G, G.1, G.1.1, G.1.2, G.1.3, G.2, G.2.1, G.2.2, G.2.3, G.2.4, G.3, G.3.1, G.3.1.1, G.3.1.2, G.3.2, G.3.2.1,G.3.2.2, G.3.3,G.3.4, G.3.5, G.3.5.1, G.3.5.2, G.4, G.4.1, G.4.2, G.4.3, G.5, G.5.1, G.5.1.1, G.5.1.2,G.5.1.3,G.5.2,G.5.2.1, G.5.2.2, G.5.2.3(Components)	-	5000	-
Annex I(Overvoltage categories)	-	1000	-
Annex. J, J.1, J.2, J.2.1, J.2.2, J.2.2.1, J.2.2.1.1, J.2.2.1.2, J.2.2.1.3, J.2.2.2, J.2.3, J.2.4, J.2.5, J.3, J.3.1, J.3.2, J.3.3(Insulated winding wires for use without interleaved insulation)	-	1000	-
Annex. K, K.1, K.1.1, K.1.2, K.2, K.3, K.4, K.5, K.5.1, K.5.2, K.6, K.6.1, K.6.2, K.7, K.7.1, K.7.2, K.7.3, K.7.4(Safety Interlocks)	-	1000	-
Annex. L, L.1, L.2, L.3, L.4, L.5, L.6, L.7, L.8, L.9,(Disconnect devices)	-	1000	-
Annex. M, M.1, M.2, M.2.1, M.2.2, M.3, M.3.1, M.3.2, M.3.3, M.4, M.4.1, M.4.2,M.4.2.1, M.4.2.2,M.4.3, M.4.4,M.4.4.1, M.4.4.2,M.4.4.3, M.4.4.4, M.4.4.5, M.4.4.6, M.5, M.5.1, M.5.2, M.6, M.6.1, M.6.2, M.7, M.7.1, M.7.2, M.7.3, M.7.3.1,M.7.3.2, M.7.3.3, M.7.(Equipment containing batteries and their protection circuits)	-	2000	-
Annex. N(Electrochemical potentials)	-	2000	-
Annex. O(Measurement of creepage distances and clearances)	-	3000	-
Annex. P, P.1, P.2, P.2.1, P.2.2, P.2.3, P.2.3.1, P.2.3.2, P.3, P.3.1, P.3.2, P.3.3, P.3.4, P.4, P.4.1, P.4.2(Safeguards against conductive objects)	-	1000	-
Annex. Q, Q.1, Q.1.1, Q.1.2, Q.2(Circuits intended for interconnection with building wiring)	-	5000	-
Annex. R, R.1, R.2, R.3, R.4(Limited short-circuit test)	-	2000	-
Annex. S, S.1, S.2, S.3, S.3.1, S.3.2, S.4, S.5(Tests for resistance to heat and fire)	-	3000	-
Annex. T, T.1, T.2, T.3, T.4, T.5, T.6, T.7, T.8, T.9, T.10, T.11(Mechanical strength tests)	-	5000	-
Annex. V, V.1, V.1.1, V.1.2, V.1.3, V.1.4, V.1.5, V.1.6, V.2(Determination of accessible parts)	-	1000	-
Annex. X(Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420V peak (300V rms))	-	1000	-
Annex. Y, Y.1, Y.2, Y.3, Y.3.1, Y.3.2, Y.3.3, Y.3.4, Y.3.5, Y.4, Y.4.1 Y.4.2, Y.4.3, Y.4.4, Y.4.5, Y.5, Y.5.1, Y.5.2, Y.5.3, Y.5.4, Y.5.5, Y.5.5.1, Y.5.5.2, Y.5.5.3, Y.6, Y.6.1, Y.6.2(Construction requirements for outdoor enclosure)	-	5000	-
10(Radiation)	-	5000	-
Annex C, C.1 & C.2(UV radiation)	-	5000	-

Complete

19 Mar, 2026

-
including w.e.f. 09.10.2024

IS 18663 (2024)

Note Sorting Machines- Specifications

Note Sorting Machines

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.2 Safety requirements (Cl 4.1 and subclauses of IS/IEC 62368-1)(General Requirements)	-	0	-
Cl 4.2 Safety requirements (Cl 4.2 and subclauses of IS/IEC 62368-1)(Energy source classifications)	-	0	-
Cl 4.2 Safety requirements (Cl 4.3 and subclauses of IS/IEC 62368-1)(Protection against energy sources)	-	0	-
Cl 4.2 Safety requirements (Cl 4.4 and subclauses of IS/IEC 62368-1)(Safeguards)	-	0	-
Cl 4.2 Safety requirements (Cl 4.5 and subclauses of IS/IEC 62368-1)("Explosion- Requirements ")	-	0	-
Cl 4.2 Safety requirements (Cl 4.6 and subclauses of IS/IEC 62368-1)(Fixing of conductors- Requirements)	-	0	-
Cl 4.2 Safety requirements (Cl 4.7 and subclauses of IS/IEC 62368-1)(Equipment for direct insertion into mains socket-outlets)	-	0	-
Cl 4.2 Safety requirements (Cl 4.8 and subclausesof IS/IEC 62368-1)(Equipment containing coin / button cell batteries)	-	0	-
Cl 4.2 Safety requirements (Cl 4.9 and subclauses of IS/IEC 62368-1)(Likelihood of fire or shock due to entry of conductive objects)	-	0	-
Cl 4.2 Safety requirements (Cl 4.10 and subclauses of IS/IEC 62368-1)(Components requirements)	-	0	-
Cl 4.2 Safety requirements (Cl 5.2 and subclauses of IS/IEC 62368-1)(Classification and limits of electrical energy sources)	-	0	-
Cl 4.2 Safety requirements (Cl 5.3 and subclauses of IS/IEC 62368-1)(Protection against electrical energy sources)	-	0	-
Cl 4.2 Safety requirements (Cl 5.4 and subclauses of IS/IEC 62368-1)(Insulation materials and requirements)	-	0	-
Cl 4.2 Safety requirements (Cl 5.5 and subclauses of IS/IEC 62368-1)(Components as safeguards)	-	0	-
Cl 4.2 Safety requirements (Cl 5.6 and subclauses of IS/IEC 62368-1)(Protective conductor)	-	0	-
Cl 4.2 Safety requirements (Cl 5.7 and subclauses of IS/IEC 62368-1)(Prospective touch voltage, touch current and protective conductor current.)	-	0	-
Cl 4.2 Safety requirements (Cl 5.8 and subclauses of IS/IEC 62368-1)(Backfeed safeguard in battery backed up supplies)	-	0	-
Cl 4.2 Safety requirements (Cl 6.1 of IS/IEC 62368-1)(Electrically-caused fire)	-	0	-
Cl 4.2 Safety requirements (Cl 6.2 and subclauses of IS/IEC 62368-1)(Classification of power sources (PS) and potential ignition sources (PIS).)	-	0	-
Cl 4.2 Safety requirements (Cl 6.3 and subclauses of IS/IEC 62368-1)(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	0	-
Cl 4.2 Safety requirements (Cl 6.4 and subclauses of IS/IEC 62368-1)(Safeguards against fire under single fault conditions)	-	0	-
Cl 4.2 Safety requirements (Cl 6.5 and subclauses of IS/IEC 62368-1)(Internal and external wiring)	-	0	-
Cl 4.2 Safety requirements (Cl 6.6 and subclauses of IS/IEC 62368-1)(Safeguards against fire due to the connection of additional equipment)	-	0	-
Cl 4.2 Safety requirements (Cl 7, 7.1 to 7.6 and subclauses of IS/IEC 62368-1)(Injury caused by hazardous substances)	-	0	-
Cl 4.2 Safety requirements (Cl 8, 8.1 to 8.12 and subclauses of IS/IEC 62368-1)(Mechanically-caused injury)	-	0	-
Cl 4.2 Safety requirements (Cl 9, 9.1 to 9.6 and subclauses of IS/IEC 62368-1)(Thermal burn injury)	-	0	-
Cl 4.2 Safety requirements (Cl 10, 10.1 to 10.6 and subclauses of IS/IEC 62368-1)(Radiation)	-	0	-
Cl 4.2 Safety requirements (Annex.B, B.1 to B.4 including its subclauses of IS/IEC 62368-1))(Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	0	-
Cl 4.2 Safety requirements (Annex.C, C.1 to C.2 including its subclauses of IS/IEC 62368-1))(UV radiation)	-	0	-
Cl 4.2 Safety requirements (Annex. D, D.1, D.2, D.3 of IS/IEC 62368-1)(Test generators)	-	0	-
Cl 4.2 Safety requirements ( Annex E, E.1, E.2, E.3 of IS/IEC 62368-1)(Test conditions for equipment containing audio amplifiers)	-	0	-
Cl 4.2 Safety requirements ( Annex. F, F.1 to F.5 including its subclauses of IS/IEC 62368-1)(Equipment markings, instructions, and instructional safeguards)	-	0	-
Cl 4.2 Safety requirements ( Annex. G, G.1 to G.16 including its subclauses of IS/IEC 62368-1)(Components)	-	0	-
Cl 4.2 Safety requirements ( Annex. H, H1 to H3 including its subclauses of IS/IEC 62368-1)(Criteria for telephone ringing signals .)	-	0	-
Cl 4.2 Safety requirements ( Annex I of IS/IEC 62368-1)(Overvoltage categories)	-	0	-
Cl 4.2 Safety requirements ( Annex. J, J.1 to J.3 including its subclauses of IS/IEC 62368-1)(Insulated winding wires for use without interleaved insulation)	-	0	-
Cl 4.2 Safety requirements ( Annex. K, K.1 to K.7 including its subclauses of IS/IEC 62368-1)(Safety Interlocks)	-	0	-
Cl 4.2 Safety requirements ( Annex. L .L1 to L.9 including its subclauses of IS/IEC 62368-1)(Disconnect devices)	-	0	-
Cl 4.2 Safety requirements ( Annex. M, M.1 to M.10 including its subclauses of IS/IEC 62368-1)(Equipment containing batteries and their protection circuits)	-	0	-
Cl 4.2 Safety requirements ( Annex.N of IS/IEC 62368-1)(Electrochemical potentials)	-	0	-
Cl 4.2 Safety requirements ( Annex.O of IS/IEC 62368-1)(Measurement of creepage distances and clearances)	-	0	-
Cl 4.2 Safety requirements ( Annex.P, P.1 to P.4 and its subclauses of IS/IEC 62368-1)(Safeguards against conductive objects)	-	0	-
Cl 4.2 Safety requirements ( Annex.Q, Q.1 to Q.2 and its subclauses of IS/IEC 62368-1)(Circuits intended for interconnection with building wiring)	-	0	-
Cl 4.2 Safety requirements ( Annex.R, R.1 to R.4 and its subclauses of IS/IEC 62368-1)(Limited short-circuit test)	-	0	-
Cl 4.2 Safety requirements ( Annex.S S.1 to S.5 and its subclauses of IS/IEC 62368-1)(Tests for resistance to heat and fire)	-	0	-
Cl 4.2 Safety requirements ( Annex T, T.1 to T.11 and its subclauses of IS/IEC 62368-1)(Mechanical strength tests)	-	0	-
Cl 4.2 Safety requirements ( Annex U, U.1 to U.3 and its subclauses of IS/IEC 62368-1)(Mechanical strength of CRTs and protection against the effects of implosion)	-	0	-
Cl 4.2 Safety requirements ( Annex V, V.1 to V.2 and its subclauses of IS/IEC 62368-1)(Determination of accessible parts)	-	0	-
Cl 4.2 Safety requirements ( Annex X of IS/IEC 62368-1)(Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420V peak (300V rms))	-	0	-
Cl 4.2 Safety requirements ( Annex Y , Y.1 to Y.6 and its subclauses of IS/IEC 62368-1)(Construction requirements for outdoor enclosure)	-	0	-
Cl 4.2 Safety requirements (Cl 4.1 and subclauses of IS/IEC 62368-1)(General Requirements)	-	0	-
Cl 4.2 Safety requirements (Cl 4.2 and subclauses of IS/IEC 62368-1)(Energy source classifications)	-	0	-
Cl 4.2 Safety requirements (Cl 4.3 and subclauses of IS/IEC 62368-1)(Protection against energy sources)	-	0	-
Cl 4.2 Safety requirements (Cl 4.4 and subclauses of IS/IEC 62368-1)(Safeguards)	-	0	-
Cl 4.2 Safety requirements (Cl 4.5 and subclauses of IS/IEC 62368-1)("Explosion- Requirements ")	-	0	-
Cl 4.2 Safety requirements (Cl 4.6 and subclauses of IS/IEC 62368-1)(Fixing of conductors- Requirements)	-	0	-
Cl 4.2 Safety requirements (Cl 4.7 and subclauses of IS/IEC 62368-1)(Equipment for direct insertion into mains socket-outlets)	-	0	-
Cl 4.2 Safety requirements (Cl 4.8 and subclausesof IS/IEC 62368-1)(Equipment containing coin / button cell batteries)	-	0	-
Cl 4.2 Safety requirements (Cl 4.9 and subclauses of IS/IEC 62368-1)(Likelihood of fire or shock due to entry of conductive objects)	-	0	-
Cl 4.2 Safety requirements (Cl 4.10 and subclauses of IS/IEC 62368-1)(Components requirements)	-	0	-
Cl 4.2 Safety requirements (Cl 5.2 and subclauses of IS/IEC 62368-1)(Classification and limits of electrical energy sources)	-	0	-
Cl 4.2 Safety requirements (Cl 5.3 and subclauses of IS/IEC 62368-1)(Protection against electrical energy sources)	-	0	-
Cl 4.2 Safety requirements (Cl 5.4 and subclauses of IS/IEC 62368-1)(Insulation materials and requirements)	-	0	-
Cl 4.2 Safety requirements (Cl 5.5 and subclauses of IS/IEC 62368-1)(Components as safeguards)	-	0	-
Cl 4.2 Safety requirements (Cl 5.6 and subclauses of IS/IEC 62368-1)(Protective conductor)	-	0	-
Cl 4.2 Safety requirements (Cl 5.7 and subclauses of IS/IEC 62368-1)(Prospective touch voltage, touch current and protective conductor current.)	-	0	-
Cl 4.2 Safety requirements (Cl 5.8 and subclauses of IS/IEC 62368-1)(Backfeed safeguard in battery backed up supplies)	-	0	-
Cl 4.2 Safety requirements (Cl 6.1 of IS/IEC 62368-1)(Electrically-caused fire)	-	0	-
Cl 4.2 Safety requirements (Cl 6.2 and subclauses of IS/IEC 62368-1)(Classification of power sources (PS) and potential ignition sources (PIS).)	-	0	-
Cl 4.2 Safety requirements (Cl 6.3 and subclauses of IS/IEC 62368-1)(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	0	-
Cl 4.2 Safety requirements (Cl 6.4 and subclauses of IS/IEC 62368-1)(Safeguards against fire under single fault conditions)	-	0	-
Cl 4.2 Safety requirements (Cl 6.5 and subclauses of IS/IEC 62368-1)(Internal and external wiring)	-	0	-
Cl 4.2 Safety requirements (Cl 6.6 and subclauses of IS/IEC 62368-1)(Safeguards against fire due to the connection of additional equipment)	-	0	-
Cl 4.2 Safety requirements (Cl 7, 7.1 to 7.6 and subclauses of IS/IEC 62368-1)(Injury caused by hazardous substances)	-	0	-
Cl 4.2 Safety requirements (Cl 8, 8.1 to 8.12 and subclauses of IS/IEC 62368-1)(Mechanically-caused injury)	-	0	-
Cl 4.2 Safety requirements (Cl 9, 9.1 to 9.6 and subclauses of IS/IEC 62368-1)(Thermal burn injury)	-	0	-
Cl 4.2 Safety requirements (Cl 10, 10.1 to 10.6 and subclauses of IS/IEC 62368-1)(Radiation)	-	0	-
Cl 4.2 Safety requirements (Annex.B, B.1 to B.4 including its subclauses of IS/IEC 62368-1))(Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	0	-
Cl 4.2 Safety requirements (Annex.C, C.1 to C.2 including its subclauses of IS/IEC 62368-1))(UV radiation)	-	0	-
Cl 4.2 Safety requirements (Annex. D, D.1, D.2, D.3 of IS/IEC 62368-1)(Test generators)	-	0	-
Cl 4.2 Safety requirements ( Annex E, E.1, E.2, E.3 of IS/IEC 62368-1)(Test conditions for equipment containing audio amplifiers)	-	0	-
Cl 4.2 Safety requirements ( Annex. F, F.1 to F.5 including its subclauses of IS/IEC 62368-1)(Equipment markings, instructions, and instructional safeguards)	-	0	-
Cl 4.2 Safety requirements ( Annex. G, G.1 to G.16 including its subclauses of IS/IEC 62368-1)(Components)	-	0	-
Cl 4.2 Safety requirements ( Annex. H, H1 to H3 including its subclauses of IS/IEC 62368-1)(Criteria for telephone ringing signals .)	-	0	-
Cl 4.2 Safety requirements ( Annex I of IS/IEC 62368-1)(Overvoltage categories)	-	0	-
Cl 4.2 Safety requirements ( Annex. J, J.1 to J.3 including its subclauses of IS/IEC 62368-1)(Insulated winding wires for use without interleaved insulation)	-	0	-
Cl 4.2 Safety requirements ( Annex. K, K.1 to K.7 including its subclauses of IS/IEC 62368-1)(Safety Interlocks)	-	0	-
Cl 4.2 Safety requirements ( Annex. L .L1 to L.9 including its subclauses of IS/IEC 62368-1)(Disconnect devices)	-	0	-
Cl 4.2 Safety requirements ( Annex. M, M.1 to M.10 including its subclauses of IS/IEC 62368-1)(Equipment containing batteries and their protection circuits)	-	0	-
Cl 4.2 Safety requirements ( Annex.N of IS/IEC 62368-1)(Electrochemical potentials)	-	0	-
Cl 4.2 Safety requirements ( Annex.O of IS/IEC 62368-1)(Measurement of creepage distances and clearances)	-	0	-
Cl 4.2 Safety requirements ( Annex.P, P.1 to P.4 and its subclauses of IS/IEC 62368-1)(Safeguards against conductive objects)	-	0	-
Cl 4.2 Safety requirements ( Annex.Q, Q.1 to Q.2 and its subclauses of IS/IEC 62368-1)(Circuits intended for interconnection with building wiring)	-	0	-
Cl 4.2 Safety requirements ( Annex.R, R.1 to R.4 and its subclauses of IS/IEC 62368-1)(Limited short-circuit test)	-	0	-
Cl 4.2 Safety requirements ( Annex.S S.1 to S.5 and its subclauses of IS/IEC 62368-1)(Tests for resistance to heat and fire)	-	0	-
Cl 4.2 Safety requirements ( Annex T, T.1 to T.11 and its subclauses of IS/IEC 62368-1)(Mechanical strength tests)	-	0	-
Cl 4.2 Safety requirements ( Annex U, U.1 to U.3 and its subclauses of IS/IEC 62368-1)(Mechanical strength of CRTs and protection against the effects of implosion)	-	0	-
Cl 4.2 Safety requirements ( Annex V, V.1 to V.2 and its subclauses of IS/IEC 62368-1)(Determination of accessible parts)	-	0	-
Cl 4.2 Safety requirements ( Annex X of IS/IEC 62368-1)(Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420V peak (300V rms))	-	0	-
Cl 4.2 Safety requirements ( Annex Y , Y.1 to Y.6 and its subclauses of IS/IEC 62368-1)(Construction requirements for outdoor enclosure)	-	0	-
Cl-6.1, Table-4 (i)(Marking and instructions)	-	1000	-
Cl-6.1, Table-4 (ii)(Protection against access to live parts)	-	5000	-
Cl-6.1, Table-4 (iii)(Power input and current)	-	5000	-
Cl-6.1, Table-4 (iv)(Heating)	-	9000	-
Cl-6.1, Table-4 (v)(Creepage clearance and solid insulation)	-	1000	-
Cl-6.1, Table-4 (vi)(Humidity conditioning)	-	10000	-
Cl-6.1, Table-4 (vii)(Leakage current and electric strength at operating temperature)	-	9000	-
Cl-6.1, Table-4 (viii)(Provision for earthing)	-	5000	-
Cl-6.1, Table-4 (i)(Marking and instructions)	-	0	-
Cl-6.1, Table-4 (ii)(Protection against access to live parts)	-	0	-
Cl-6.1, Table-4 (iii)(Power input and current)	-	0	-
Cl-6.1, Table-4 (iv)(Heating)	-	0	-
Cl-6.1, Table-4 (v)(Creepage clearance and solid insulation)	-	0	-
Cl-6.1, Table-4 (vi)(Humidity conditioning)	-	0	-
Cl-6.1, Table-4 (vii)(Leakage current and electric strength at operating temperature)	-	0	-
Cl-6.1, Table-4 (viii)(Provision for earthing)	-	0	-
Cl-6.1, Table-4 (i)(Marking and instructions)	-	0	-
Cl-6.1, Table-4 (ii)(Protection against access to live parts)	-	0	-
Cl-6.1, Table-4 (iii)(Power input and current)	-	0	-
Cl-6.1, Table-4 (iv)(Heating)	-	0	-
Cl-6.1, Table-4 (v)(Creepage clearance and solid insulation)	-	0	-
Cl-6.1, Table-4 (vi)(Humidity conditioning)	-	0	-
Cl-6.1, Table-4 (vii)(Leakage current and electric strength at operating temperature)	-	0	-
Cl-6.1, Table-4 (viii)(Provision for earthing)	-	0	-

Complete

19 Mar, 2026

-
Included w.e.f. 27.08.2024 only for Cl.4.2 safety requirement

IS 16240 (2015)

Reverse osmosis (RO) based point-of-use (POU) water treatment system - Specification

Reverse Osmosis (RO) Based Point-of-Use (PoU) Water

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.5(Electrical Safety)	-	6500	5% discount for BIS
6.7(Type Pressure Test (Hydrostatic Test))	-	3500	5% discount for BIS
7(Pneumatic test)	-	3500	5% discount for BIS

Complete

19 Mar, 2026

-
-

IS 16444 : Part 2 (2017)

AC static transformer operated watthour and var - Hour smart meters, class 0.2 S, 0.5 S and 1.0 S: Part 2 specification transformer operated smart meters

Class 0.2 S, 0.5 S and 1.0 S

229500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.8.1(Additional information)	-	0	Charges Covered in Marking of meter Name plate Cl. 6.8
6.8(Connection diagrams and terminal marking)	-	0	Charges Covered in Marking of meter Name plate Cl. 6.8
6.8(BIS Standard Mark)	-	0	Charges Covered in Marking of meter Name plate Cl. 6.8
6.8(Marking of meters Name plate)	-	1200	5% discount for BIS
6.3(Clearance and creepage distances)	-	500	5% discount for BIS
10.0(Smart Meter Functional Requirements)	-	12000	5% discount for BIS
9.3(Test of Display)	-	200	5% discount for BIS
7, 9.4(Data Exchange for Electricity Meter Reading, Tariff and Load Control Companion Specification (The requirement as per IS 15959 : Part 1 & Part 3 shall apply))	-	56000	5% discount for BIS
6.4(Test of resistance to heat and fire)	-	4000	5% discount for BIS
Note b of Table 1(Access and data read test)	-	1500	5% discount for BIS
Note a of Table 1(Accuracy of the meter at pre-defined points)	-	200	5% discount for BIS
6.5(Test of protection against penetration of dust and water)	-	5500	5% discount for BIS
6.5(Spring hammer test)	-	300	5% discount for BIS
6.5(Shock test)	-	4500	5% discount for BIS
6.5(Vibration test)	-	7000	5% discount for BIS
6.9(Damp heat cyclic test)	-	5800	5% discount for BIS
6.9(Cold test)	-	4000	5% discount for BIS
6.9(Dry heat test)	-	1200	5% discount for BIS
6.11(Test of immunity to electrostatic discharge)	-	7500	5% discount for BIS
6.11(Fast transient burst test)	-	12500	5% discount for BIS
6.11(Radio interference measurement)	-	25000	5% discount for BIS
6.10.7(Test of immunity to earth/phase fault)	-	2500	5% discount for BIS
6.10.5(Test of influence of heating)	-	1500	5% discount for BIS
6.10.4(Test of influence of self-heating)	-	1200	5% discount for BIS
6.10.3(Test of influence of short time over currents)	-	5000	5% discount for BIS
6.10.2(Test of influence of supply voltage)	-	10500	5% discount for BIS
6.10.1(Test of power consumption)	-	700	5% discount for BIS
6.12(Operation of Accessories)	-	1000	5% discount for BIS
6.12(Abnormal Magnetic Induction of External Origin 10mT)	-	1500	5% discount for BIS
6.12(Magnetic induction of External Origin 0.5mT)	-	1500	5% discount for BIS
6.12(Continuous Magnetic Induction of External Origin 0.2 Tesla)	-	1500	5% discount for BIS
6.12(Continuous Magnetic Induction of External Origin 67 milli Tesla)	-	1500	5% discount for BIS
6.12(Voltage Unbalanced)	-	500	5% discount for BIS
6.12(Reversed Phase Sequence)	-	500	5% discount for BIS
6.12(Waveform 10% of 3rd Harmonics)	-	1200	5% discount for BIS
6.12(Frequency Variation)	-	500	5% discount for BIS
6.12(Voltage Variation)	-	500	5% discount for BIS
6.12(Test of influence quantities)	-	2000	additional Test wise charges as per added
6.12(Test of repeatability of error)	-	3500	5% discount for BIS
6.12(Test of ambient temperature influence)	-	2500	5% discount for BIS
6.12(Test of no-load condition)	-	500	5% discount for BIS
6.12(Test of starting condition)	-	500	5% discount for BIS
6.12(Test of meter constant)	-	1000	5% discount for BIS
6.12(Test on limits of error)	-	2000	5% discount for BIS
6.10.6(Insulation test)	-	500	5% discount for BIS
6.10.6(ac high voltage test)	-	500	5% discount for BIS
6.10.6(Impulse voltage test)	-	4000	5% discount for BIS
6.7(Output device)	-	1500	5% discount for BIS
6.6(Display of measured values)	-	500	5% discount for BIS
6.2.2(Insulating encased meter)	-	0	Charges Covered in General and constructional requirements Cl. 6.2
6.2.2(Terminal Cover(s))	-	0	Charges Covered in General and constructional requirements Cl. 6.2
6.2.1(Terminals, terminal block and protective earth terminal)	-	0	Charges Covered in General and constructional requirements Cl. 6.2
6.2(Communication module)	-	0	Charges Covered in General and constructional requirements Cl. 6.2
6.2(Window)	-	0	Charges Covered in General and constructional requirements Cl. 6.2
6.2(Meter case)	-	0	Charges Covered in General and constructional requirements Cl. 6.2
6.2(General Constructional requirements)	-	2000	5% discount for BIS
6.1(Electrical Requirments)	-	0	Qualitative
6.1(Electrical Requirments)	-	0	Qualitative
6.1(Electrical Requirments)	-	0	Qualitative
6.1(Electrical Requirments)	-	0	Qualitative
6.1(Electrical Requirments)	-	0	Qualitative
6.12((11 of IS 14697 ) Accuracy Requirement )	-	0	Test wise charges as per added
6.8(Inspection )	-	0	Charges Covered in Marking of meter Name plate Cl. 6.8
6.8(Inspection ( 7 of IS 14697) )	-	0	Charges Covered in Marking of meter Name plate Cl. 6.8
8, 9.5(Smart Meter Communicability)	-	18000	5% discount for BIS
6.11(Surge Immunity test)	-	10000	5% discount for BIS
6.11(Test of immunity to electromagnetic HF field)	-	35000	5% discount for BIS
6.11(Surge Immunity test)	-	25000	5% discount for BIS

Complete

19 Mar, 2026

-
-

IS 1258 (2005)

Bayonet lamp holders (Fourth Revision)

Bayonet Lamp Holders

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Marking )	-	100	-
8.2(Marking )	-	100	-
8.3(Marking )	-	100	-
8.4(Marking )	-	100	-
8.5(Marking )	-	100	-
8.6(Marking )	-	100	-
8.7(Marking )	-	100	-
8.8(Marking )	-	100	-
6(Rating )	-	50	-
6(Rating )	-	50	-
7(Classification)	-	50	-
7.2(Classification)	-	50	-
7.3(Classification)	-	50	-
7.4(Classification)	-	50	-
7.5(Classification)	-	50	-
7.6(Classification)	-	50	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.2(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
10(Protection against electric shock )	-	750	-
11.1(Terminals)	-	500	-
11.2(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.4(Terminals)	-	500	-
12(Provision for Earthing)	-	750	-
13.1(Construction)	-	500	-
13.1(Construction (Data Sheet No 7005-10))	-	500	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	500	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	500	-
13.3(Construction )	-	500	-
13.4(Construction )	-	500	-
13.5(Construction)	-	500	-
13.2 ,13.6 & 13.7 (Construction)	-	500	-
13.2 ,13.6 & 13.8(Construction)	-	500	-
13.11(Construction)	-	500	-
14(Construction)	-	1000	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1500	-
15.2(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1500	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1500	-
16.1(Mechanical Strength)	-	1250	-
16.1(Mechanical Strength)	-	1250	-
16.2(Mechanical Strength)	-	1250	-
16.3(Mechanical Strength)	-	1250	-
16.4(Mechanical Strength)	-	1250	-
16.5(Mechanical Strength)	-	1250	-
16.6 & Table - 6(Mechanical Strength)	-	1250	-
16.7(Mechanical Strength)	-	1250	-
16.8(Mechanical Strength)	-	1250	-
17(Screws,current-carrying parts and connections)	-	750	-
18(Creepage distances and Clearances)	-	600	-
18.1, Table 8(Creepage distances and Clearances)	-	600	-
18.1, Table 8(Creepage distances and Clearances)	-	600	-
18.1, Table 8(Creepage distances and Clearances)	-	600	-
18.1, Table 8(Creepage distances and Clearances)	-	600	-
18.1, Table 8(Creepage distances and Clearances)	-	600	-
18.1, Table 8(Creepage distances and Clearances)	-	600	-
18.1, Table 8(Creepage distances and Clearances)	-	600	-
19.1(General resistance to heat)	-	1250	-
19.2(General resistance to heat)	-	1250	-
19.3(General resistance to heat)	-	1250	-
19.4(Resistance to heat test)	-	1250	-
20.1(Resistance to heat, fire and tracking)	-	2250	-
20.3(Resistance to heat, fire and tracking)	-	2250	-
20.4(Resistance to heat, fire and tracking)	-	2250	-
20.5(Resistance to tracking)	-	2250	-
21.1(Resistance to excessive residual stresses and to rusting)	-	3000	-
21.1(Resistance to excessive residual stresses and to rusting)	-	3000	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.1(Marking )	-	100	-
8.2(Marking )	-	100	-
8.2(Marking )	-	100	-
8.2(Marking )	-	100	-
8.3(Marking )	-	100	-
8.4(Marking )	-	100	-
8.5(Marking )	-	100	-
8.6(Marking )	-	100	-
8.7(Marking )	-	100	-
8.8(Marking )	-	100	-
6(Rating )	-	50	-
6(Rating )	-	50	-
7(Classification)	-	50	-
7.2(Classification)	-	50	-
7.3(Classification)	-	50	-
7.4(Classification)	-	50	-
7.5(Classification)	-	50	-
7.6(Classification)	-	50	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.1(Dimensions)	-	200	-
9.2(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
9.3(Dimensions)	-	200	-
10(Protection against electric shock )	-	750	-
11.1(Terminals)	-	500	-
11.2(Terminals)	-	500	-
11.3(Terminals)	-	500	-
12.3(Terminals)	-	750	-
11.3(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.3(Terminals)	-	500	-
11.4(Terminals)	-	500	-
12(Provision for Earthing)	-	750	-
13.1(Construction)	-	500	-
13.1(Construction (Data Sheet No 7005-10))	-	500	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	500	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	500	-
13.3(Construction )	-	500	-
13.4(Construction )	-	500	-
13.5(Construction)	-	500	-
13.2 ,13.6 & 13.7 (Construction)	-	500	-
13.2 ,13.6 & 13.8(Construction)	-	500	-
13.11(Construction)	-	500	-
14(Construction)	-	1000	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1500	-
15.2(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1500	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	1500	-
16.1(Mechanical Strength)	-	1250	-
16.1(Mechanical Strength)	-	1250	-
16.2(Mechanical Strength)	-	1250	-
16.3(Mechanical Strength)	-	1250	-
16.4(Mechanical Strength)	-	1250	-
16.5(Mechanical Strength)	-	1250	-
16.6 & Table - 6(Mechanical Strength)	-	1250	-
16.7(Mechanical Strength)	-	1250	-
16.8(Mechanical Strength)	-	1250	-
17(Screws,current-carrying parts and connections)	-	750	-
18(Creepage distances and Clearances)	-	600	-
18(Creepage distances and Clearances)	-	600	-
18(Creepage distances and Clearances)	-	600	-
18(Creepage distances and Clearances)	-	600	-
18(Creepage distances and Clearances)	-	600	-
18(Creepage distances and Clearances)	-	600	-
18(Creepage distances and Clearances)	-	600	-
18(Creepage distances and Clearances)	-	600	-
19.1(General resistance to heat)	-	1250	-
19.2(General resistance to heat)	-	1250	-
19.3(General resistance to heat)	-	1250	-
19.4(Resistance to heat test)	-	1250	-
20.1(Resistance to heat, fire and tracking)	-	2250	-
20.3(Resistance to heat, fire and tracking)	-	2250	-
20.4(Resistance to heat, fire and tracking)	-	2250	-
20.5(Resistance to tracking)	-	2250	-
21.1(Resistance to excessive residual stresses and to rusting)	-	3000	-
21.1(Resistance to excessive residual stresses and to rusting)	-	3000	-
8.1(Marking )	-	0	-
8.2(Marking )	-	0	-
8.3(Marking )	-	0	-
8.4(Marking )	-	0	-
8.5(Marking )	-	0	-
8.6(Marking )	-	0	-
8.7(Marking )	-	0	-
8.8(Marking )	-	0	-
6(Rating )	-	0	-
6(Rating )	-	0	-
7(Classification)	-	0	-
7.2(Classification)	-	0	-
7.3(Classification)	-	0	-
7.4(Classification)	-	0	-
7.5(Classification)	-	0	-
7.6(Classification)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.2(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
10(Protection against electric shock )	-	0	-
11.1(Terminals)	-	0	-
11.2(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.4(Terminals)	-	0	-
12(Provision for Earthing)	-	0	-
13.1(Construction)	-	0	-
13.1(Construction (Data Sheet No 7005-10))	-	0	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	0	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	0	-
13.3(Construction )	-	0	-
13.4(Construction )	-	0	-
13.5(Construction)	-	0	-
13.2 ,13.6 & 13.7 (Construction)	-	0	-
13.2 ,13.6 & 13.8(Construction)	-	0	-
13.11(Construction)	-	0	-
14(Construction)	-	0	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	0	-
15.2(Moisture Resistance, Insulation Resistance and Electric Strength)	-	0	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	0	-
16.1(Mechanical Strength)	-	0	-
16.1(Mechanical Strength)	-	0	-
16.2(Mechanical Strength)	-	0	-
16.3(Mechanical Strength)	-	0	-
16.4(Mechanical Strength)	-	0	-
16.5(Mechanical Strength)	-	0	-
16.6 & Table - 6(Mechanical Strength)	-	0	-
16.7(Mechanical Strength)	-	0	-
16.8(Mechanical Strength)	-	0	-
17(Screws,current-carrying parts and connections)	-	0	-
18(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
18.1, Table 8(Creepage distances and Clearances)	-	0	-
19.1(General resistance to heat)	-	0	-
19.2(General resistance to heat)	-	0	-
19.3(General resistance to heat)	-	0	-
19.4(Resistance to heat test)	-	0	-
20.1(Resistance to heat, fire and tracking)	-	0	-
20.3(Resistance to heat, fire and tracking)	-	0	-
20.4(Resistance to heat, fire and tracking)	-	0	-
20.5(Resistance to tracking)	-	0	-
21.1(Resistance to excessive residual stresses and to rusting)	-	0	-
21.1(Resistance to excessive residual stresses and to rusting)	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.1(Marking )	-	0	-
8.2(Marking )	-	0	-
8.2(Marking )	-	0	-
8.2(Marking )	-	0	-
8.3(Marking )	-	0	-
8.4(Marking )	-	0	-
8.5(Marking )	-	0	-
8.6(Marking )	-	0	-
8.7(Marking )	-	0	-
8.8(Marking )	-	0	-
6(Rating )	-	0	-
6(Rating )	-	0	-
7(Classification)	-	0	-
7.2(Classification)	-	0	-
7.3(Classification)	-	0	-
7.4(Classification)	-	0	-
7.5(Classification)	-	0	-
7.6(Classification)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.1(Dimensions)	-	0	-
9.2(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
9.3(Dimensions)	-	0	-
10(Protection against electric shock )	-	0	-
11.1(Terminals)	-	0	-
11.2(Terminals)	-	0	-
11.3(Terminals)	-	0	-
12.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.3(Terminals)	-	0	-
11.4(Terminals)	-	0	-
12(Provision for Earthing)	-	0	-
13.1(Construction)	-	0	-
13.1(Construction (Data Sheet No 7005-10))	-	0	-
13.1(Construction (Data Sheet No 7005-10& 7006-15A))	-	0	-
13.2(Construction (Data Sheet No 7005-10& 7006-15A))	-	0	-
13.3(Construction )	-	0	-
13.4(Construction )	-	0	-
13.5(Construction)	-	0	-
13.2 ,13.6 & 13.7 (Construction)	-	0	-
13.2 ,13.6 & 13.8(Construction)	-	0	-
13.11(Construction)	-	0	-
14(Construction)	-	0	-
15.1(Moisture Resistance, Insulation Resistance and Electric Strength)	-	0	-
15.2(Moisture Resistance, Insulation Resistance and Electric Strength)	-	0	-
15.3(Moisture Resistance, Insulation Resistance and Electric Strength)	-	0	-
16.1(Mechanical Strength)	-	0	-
16.1(Mechanical Strength)	-	0	-
16.2(Mechanical Strength)	-	0	-
16.3(Mechanical Strength)	-	0	-
16.4(Mechanical Strength)	-	0	-
16.5(Mechanical Strength)	-	0	-
16.6 & Table - 6(Mechanical Strength)	-	0	-
16.7(Mechanical Strength)	-	0	-
16.8(Mechanical Strength)	-	0	-
17(Screws,current-carrying parts and connections)	-	0	-
18(Creepage distances and Clearances)	-	0	-
18(Creepage distances and Clearances)	-	0	-
18(Creepage distances and Clearances)	-	0	-
18(Creepage distances and Clearances)	-	0	-
18(Creepage distances and Clearances)	-	0	-
18(Creepage distances and Clearances)	-	0	-
18(Creepage distances and Clearances)	-	0	-
18(Creepage distances and Clearances)	-	0	-
19.1(General resistance to heat)	-	0	-
19.2(General resistance to heat)	-	0	-
19.3(General resistance to heat)	-	0	-
19.4(Resistance to heat test)	-	0	-
20.1(Resistance to heat, fire and tracking)	-	0	-
20.3(Resistance to heat, fire and tracking)	-	0	-
20.4(Resistance to heat, fire and tracking)	-	0	-
20.5(Resistance to tracking)	-	0	-
21.1(Resistance to excessive residual stresses and to rusting)	-	0	-
21.1(Resistance to excessive residual stresses and to rusting)	-	0	-

Complete

19 Mar, 2026

-
including w.e.f 09.10.2024

IS 14286 : Part 1 : Sec 4 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-4: Special requirements for testing of thin-film CuInGASSe2 based photovoltaic PV modules Third Revision

1502500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	6000	-
Cl-11.1(Visual inspection (MQT 01))	-	2000	-
Cl-11.2(Maximum power determination (MQT 02))	-	7000	-
Cl-11.3(Insulation test (MQT 03))	-	20000	-
Cl-11.4(Measurement of temperature coefficients (MQT 04))	-	110000	-
Cl-11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	5000	-
Cl-11.6(Performance at STC (MQT 06.1) and NMOT (MQT 06.2)	-	2500	-
Cl-11.7(Performance at low irradiance (MQT 07))	-	10000	-
Cl-11.8(Outdoor exposure test (MQT 08))	-	50000	-
Cl-11.9(Hot-spot endurance test (MQT 09))	-	125000	-
Cl-11.10(UV preconditioning test (MQT 10))	-	125000	-
Cl-11.11(Thermal cycling test (MQT 11))	-	160000	-
Cl-11.12(As per IEC 61215-1:2016)	-	80000	-
Cl-11.13(Damp heat test (MQT 13))	-	160000	-
Cl-11.14(Robustness of terminations test (MQT 14))	-	15000	-
Cl-11.15(Robustness of terminations test (MQT 14))	-	25000	-
Cl-11.16(Static mechanical load test (MQT 16))	-	50000	-
Cl-11.17(Hail test (MQT 17))	-	50000	-
Cl-11.18(Bypass diode testing (MQT 18))	-	75000	-
Cl-11.19(Stabilization (MQT 19))	-	95000	-

Complete

19 Mar, 2026

-
-

IS 14286 : Part 1 : Sec 3 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic PV modules Third Revision

1502500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	6000	-
Cl-11.1(Visual inspection)	-	2000	-
Cl-11.2(Maximum power determination)	-	7000	-
Cl-11.3(Insulation test)	-	20000	-
Cl-11.4(Measurement of temperature coefficients)	-	110000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	5000	-
Cl-11.6(Performance at STC and NMOT)	-	2500	-
Cl-11.7(Performance at low irradiance)	-	10000	-
Cl-11.8(Outdoor exposure test)	-	50000	-
Cl-11.9(Hot-spot endurance test)	-	125000	-
Cl-11.10(UV preconditioning test)	-	125000	-
Cl-11.11(Thermal cycling test)	-	160000	-
Cl-11.12(Humidity-freeze test)	-	80000	-
Cl-11.13(Damp heat test)	-	160000	-
Cl-11.14(Robustness of terminations test)	-	15000	-
Cl-11.15(Wet leakage current test)	-	25000	-
Cl-11.16(Static mechanical load test)	-	50000	-
Cl-11.17(Hail test)	-	50000	-
Cl-11.18(Bypass diode testing)	-	75000	-
Cl-11.19(Stabilization)	-	95000	-

Complete

19 Mar, 2026

-
-

IS 14286 : Part 1 : Sec 2 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-2: Special requirements for testing of thin-film Cadmium Telluride CdTe based photovoltaic PV modules Third Revision

Thin-film Cadmium Telluride CdTe based PV Modules

1502500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	6000	-
Cl-11.1(Visual inspection)	-	2000	-
Cl-11.2(Maximum power determination)	-	7000	-
Cl-11.3(Insulation tes)	-	20000	-
Cl-11.4(Measurement of temperature coefficients)	-	110000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	5000	-
Cl-11.6(Performance at STC and NMOT)	-	2500	-
Cl-11.7(Performance at low irradiance)	-	10000	-
Cl-11.8(Outdoor exposure test)	-	50000	-
Cl-11.9(Hot-spot endurance test)	-	125000	-
Cl-11.10(UV preconditioning test)	-	125000	-
Cl-11.11(Thermal cycling test)	-	160000	-
Cl-11.12(Humidity-freeze test)	-	80000	-
Cl-11.13(Damp heat test)	-	160000	-
Cl-11.14(Robustness of terminations test)	-	15000	-
Cl-11.15(Wet leakage current test)	-	25000	-
Cl-11.16(Static mechanical load test)	-	50000	-
Cl-11.17(Hail test)	-	50000	-
Cl-11.18(Bypass diode testing)	-	75000	-
Cl-11.19(Stabilization)	-	95000	-

Complete

19 Mar, 2026

-
-

IS 14286 : Part 1 : Sec 1 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-1: Special requirements for testing of crystalline silicon photovoltaic PV modules Third Revision

1502500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	6000	-
Cl-11.1(Visual inspection)	-	2000	-
Cl-11.2(Maximum power determination)	-	7000	-
Cl-11.3(Insulation test)	-	20000	-
Cl-11.4(Measurement of temperature coefficients)	-	110000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	5000	-
Cl-11.6(Performance at STC)	-	2500	-
Cl-11.7(Performance at low irradiance)	-	10000	-
Cl-11.8(Outdoor exposure test)	-	50000	-
Cl-11.9(Hot-spot endurance test)	-	125000	-
Cl-11.10(UV preconditioning test)	-	125000	-
Cl-11.11(Thermal cycling test)	-	160000	-
Cl-11.12(Humidity-freeze test)	-	80000	-
Cl-11.13(Damp heat test)	-	160000	-
Cl-11.14(Robustness of terminations test)	-	15000	-
Cl-11.15(Wet leakage current tes)	-	25000	-
Cl-11.16(Static mechanical load test)	-	50000	-
Cl-11.17(Hail test)	-	50000	-
Cl-11.18(Bypass diode thermal test)	-	75000	-
Cl-11.19(Stabilization)	-	95000	-

Complete

19 Mar, 2026

-
including w.e.f. 09.10.2024

IS 11328 (2022)

Self-contained Automatic Ice Makers Specification (First Revision)

Self-contained Automatic Ice Makers

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Construction)	-	250	5% discount for BIS
Cl-5.2(Water Condensation)	-	250	5% discount for BIS
Cl-5.3(Safety Features in Design)	-	250	5% discount for BIS
Cl-5.4(Control of Operation)	-	250	5% discount for BIS
Cl-5.5(Location of the Components)	-	250	5% discount for BIS
Cl-6.1(Motors)	-	250	5% discount for BIS
Cl-6.3(Motor Starters, Relays, Thermostat, Controls, etc)	-	250	5% discount for BIS
Cl-6.4(Wiring)	-	250	5% discount for BIS
Cl-6.5(Electrical Accessories)	-	250	5% discount for BIS
Cl-6.6(Earth Connection)	-	250	5% discount for BIS
Cl-7.1(General Requirements for Tests)	-	250	5% discount for BIS
Cl-7.2(Ice Weighing Instruments)	-	250	5% discount for BIS
Cl-7.3(Type Tests)	-	16000	5% discount for BIS
Cl-7.4(Routine Tests)	-	7000	5% discount for BIS
Cl-7.5(Acceptance Tests)	-	16000	5% discount for BIS
Cl-7.6(Test Procedure)	-	16000	5% discount for BIS
Cl-8(Marking)	-	250	5% discount for BIS

Complete

19 Mar, 2026

-
-

IS 16614 : Part 2 (2022)

Double-Capped LED Linear Lamps Part 2 Performance Specification

Double Capped LED Linear Lamps

98500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Requirements on Tests)	-	0	-
5(Marking)	-	250	5% discount for BIS
6(Dimensions)	-	750	5% discount for BIS
7.1(General Test Conditions)	-	0	-
7.2(Creation of LED Lamp Families to reduce test effort)	-	0	-
8.1(Lamp Power)	-	1000	5% discount for BIS
8.2(Power Factor)	-	1000	5% discount for BIS
8.3(Harmonics)	-	5000	5% discount for BIS
8.4(Emission of Radio Frequency Disturbances)	-	5000	5% discount for BIS
9.1(Luminous Flux)	-	5000	5% discount for BIS
9.2(Luminous intensity distribution, peak intensity and beam angle)	-	2000	5% discount for BIS
9.3(Luminous Efficacy)	-	5000	5% discount for BIS
10(COLORIMETRIC CHARACTERISTICS)	-	2000	5% discount for BIS
11(Lamp Life)	-	67500	5% discount for BIS
12(Dimming)	-	0	-
14.1(Type Tests)	-	0	-
14.2(Acceptance Tests)	-	0	-

Complete

19 Mar, 2026

-
-

IS 16270 (2023)

Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

Secondary Cells and Batteries for Solar Photovoltaic Ap

575000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Photovoltaic Energy System)	-	0	-
Cl-4.2(Secondary Cells and Batteries)	-	0	-
Cl-4.3(General Operating Conditions)	-	0	-
Cl-4.3.8(Storage)	-	0	-
Cl-4.3.9(Operating Temperature)	-	0	-
Cl-5.1(Mechanical Endurance)	-	0	-
Cl-5.2(Charge Efficiency)	-	0	-
Cl-5.3(Deep Discharge Protection)	-	0	-
Cl-5.4(Marking)	-	2500	-
Cl-5.5(Safety)	-	0	-
Cl-5.6(Documentation)	-	0	-
Cl-6(Functional characteristice)	-	0	-
Cl-7(General test conditions)	-	0	-
Cl-8.1(Capacity Test)	-	125000	-
Cl-8.2(Endurance Test)	-	132500	-
Cl-8.3(Charge Retention Test)	-	100000	-
Cl-8.4(Cycle Endurance in Photovoltaic Application (Extreme Conditions))	-	125000	-
Cl-8.5(Sulphation Test (Applicable for Lead Acid Batteries only))	-	42500	-
Cl-8.6(Water Loss Test (Valid for Flooded Lead Acid Batteries only))	-	47500	-
Cl-9.1(Type Tests)	-	0	-
Cl-9.2(Acceptance Test)	-	0	-

Complete

19 Mar, 2026

-
-

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

Thermosetting Insulated Fire Survival Cables

136000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	3500	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	1000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	1000	-
IS 191:2007 & IS 440(Copper purity test)	-	1000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	3000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	750	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	750	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	750	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	500	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	3500	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	6000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	4000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	12500	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	500	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	500	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	500	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	500	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	500	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	1000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	1000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	7500	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	3000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	500	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	3000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	12500	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	6000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	4000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	1000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	500	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	500	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	5000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	17500	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	1000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	1000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	17500	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	3000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	11000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	500	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	1000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	7500	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	17500	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	3500	-

Complete

19 Mar, 2026

-
-

IS 17293 (2020)

Electric Cables for Photovoltaic Systems for Rated Voltage 1 500 V d.c.

Electric cables for photovoltaic system

1055000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	1500	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	2500	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	2500	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	14500	-
IS 191 : 2007, IS 440(Copper purity test)	-	5000	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	10000	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	1500	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	12500	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	125000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	2500	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	12500	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	12500	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	12500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	2000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	32500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	32500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	32500	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	500	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	350000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	17500	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	3500	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	7500	-
Annex - B of IS 17293:2020(Compatibility test)	-	500	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	7500	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	2500	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	12500	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	12500	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	7500	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	17500	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	12500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	32500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	32500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	32500	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	32500	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	7500	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	350000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	2500	-
Annex - B of IS 17293:2020(Compatibility test)	-	2500	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	7500	-
Annex - E of IS 17293 : 2020(UV resistance)	-	95000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	2000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	2500	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	17500	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	17500	-
11.2.2(Spark Test)	-	2500	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	25000	-
11.2.5(Surface Resistance of Sheath)	-	2500	-
11.3.1(Sheath Colour)	-	500	-
11.3.2(Sheath Marking)	-	750	-
11.3.3(Overall Diameters and Ovality)	-	1500	-
Annex J(Assessment of Halogens)	-	32500	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	2500	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	7500	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	7500	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	350000	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	12500	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	12500	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	2500	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	2500	-
5.2(Application to the Conductor)	-	500	-
5.3(Thickness)	-	1500	-
6.2(Sheath application)	-	500	-
6.3(Sheath Thickness)	-	1500	-
6.4(Sheath Colour)	-	500	-
7(Overall Dimension)	-	1500	-
8.1(Continuity of Marking)	-	750	-
8.2(Durability)	-	500	-
8.3(Legibility)	-	500	-
9(Core Identification)	-	500	-
12(Packing and Marking)	-	750	-
4.1(Resistance)	-	500	-
7.1.2.1, 7.2.3(Annealing)	-	2500	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	12500	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	0	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	0	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	0	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	0	-
IS 191 : 2007, IS 440(Copper purity test)	-	0	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	0	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	0	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	0	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	0	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	0	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	0	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Annex - E of IS 17293 : 2020(UV resistance)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
11.2.2(Spark Test)	-	0	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	0	-
11.2.5(Surface Resistance of Sheath)	-	0	-
11.3.1(Sheath Colour)	-	0	-
11.3.2(Sheath Marking)	-	0	-
11.3.3(Overall Diameters and Ovality)	-	0	-
Annex J(Assessment of Halogens)	-	0	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	0	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	0	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	0	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	0	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	0	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	0	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	0	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	0	-
5.2(Application to the Conductor)	-	0	-
5.3(Thickness)	-	0	-
6.2(Sheath application)	-	0	-
6.3(Sheath Thickness)	-	0	-
6.4(Sheath Colour)	-	0	-
7(Overall Dimension)	-	0	-
8.1(Continuity of Marking)	-	0	-
8.2(Durability)	-	0	-
8.3(Legibility)	-	0	-
9(Core Identification)	-	0	-
12(Packing and Marking)	-	0	-
4.1(Resistance)	-	0	-
7.1.2.1, 7.2.3(Annealing)	-	0	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	0	-

Complete

19 Mar, 2026

-
-

IS 302 : Part 2 : Sec 7 (2024)

Safety of Household And Similar Electrical Appliances Part 2 Particular Requirements Section 7: Domestic Electric Clothes Washing Machines

Domestic electric clothes washing machines

195000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(GENERAL REQUIREMENT)	-	1000	5% discount for BIS
6(CLASSIFICATION)	-	1000	5% discount for BIS
7(MARKING AND INSTRUCTIONS)	-	2000	5% discount for BIS
8(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	2500	5% discount for BIS
10(POWER INPUT AND CURRENT)	-	4000	5% discount for BIS
11(HEATING)	-	5000	5% discount for BIS
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	4500	5% discount for BIS
14(TRANSIENT OVERVOLTAGES)	-	5500	5% discount for BIS
15(MOISTURE RESISTANCE)	-	15000	5% discount for BIS
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	5000	5% discount for BIS
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	4000	5% discount for BIS
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	4000	5% discount for BIS
18(ENDURANCE)	-	10000	5% discount for BIS
19(ABNORMAL OPERATION)	-	45000	5% discount for BIS
19.11.4.1(Electrostatic discharges)	-	45000	5% discount for BIS
19.11.4.2(Radiated fields)	-	45000	5% discount for BIS
19.11.4.5(Immunity to conducted discharges)	-	45000	5% discount for BIS
19.11.4.6(Class 3 Voltage dips and interruptions)	-	45000	5% discount for BIS
19.11.4.7(Harmonics)	-	45000	5% discount for BIS
20(STABILITY AND MECHANICAL HAZARDS)	-	30000	5% discount for BIS
21(MECHANICAL STRENGTH)	-	5000	5% discount for BIS
22(CONSTRUCTION)	-	30000	5% discount for BIS
23(INTERNAL WIRING)	-	2500	5% discount for BIS
24(COMPONENTS)	-	2500	5% discount for BIS
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2500	5% discount for BIS
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	3000	5% discount for BIS
27(PROVISION FOR EARTHING)	-	3000	5% discount for BIS
28(SCREWS AND CONNECTIONS)	-	3000	5% discount for BIS
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2500	5% discount for BIS
30(RESISTANCE TO HEAT AND FIRE)	-	3000	5% discount for BIS
31(RESISTANCE TO RUSTING)	-	2500	5% discount for BIS
4(GENERAL REQUIREMENT)	-	0	-
6(CLASSIFICATION)	-	0	-
7(MARKING AND INSTRUCTIONS)	-	0	-
8(PROTECTION AGAINST ACCESS TO LIVE PARTS)	-	0	-
10(POWER INPUT AND CURRENT)	-	0	-
11(HEATING)	-	0	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	0	-
14(TRANSIENT OVERVOLTAGES)	-	0	-
15(MOISTURE RESISTANCE)	-	0	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	0	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	0	-
17("OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS ")	-	0	-
18(ENDURANCE)	-	0	-
19(ABNORMAL OPERATION)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
20(STABILITY AND MECHANICAL HAZARDS)	-	0	-
21(MECHANICAL STRENGTH)	-	0	-
22(CONSTRUCTION)	-	0	-
23(INTERNAL WIRING)	-	0	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	0	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	0	-
27(PROVISION FOR EARTHING)	-	0	-
28(SCREWS AND CONNECTIONS)	-	0	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	0	-
30(RESISTANCE TO HEAT AND FIRE)	-	0	-
31(RESISTANCE TO RUSTING)	-	0	-
19.11.4.3(Fast transient bursts)	-	45000	5% discount for BIS
19.11.4.4(Surge immunity test)	-	45000	5% discount for BIS
19.13(ABNORMAL OPERATION)	-	45000	5% discount for BIS
19.101(Abnormal Operation)	-	45000	5% discount for BIS
19.102(Abnormal Operation)	-	45000	5% discount for BIS

Complete

19 Mar, 2026

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Bharat Test House Pvt Ltd 1474 Haryana

1474, HSIIDC Rai Industrial Estate, SONIPAT, Sonipat, Haryana, 131029

9310314585 bthrai@bharattesthouse.com

Scope List