BIS - LIMS (Laboratory Information Management System)

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

198-199, MIE, Industrial Area, Phase-1, Bahadurgarh, Haryana, Bahadurgarh, Jhajjar, Haryana, 124507

9818233966 info@alphatesthouse.com

Scope List

Reset

148 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 17399 (2020)

Textiles - Polypropylene ( PP )/ High Density Polyethylene ( HDPE ) Laminated Woven Sacks for Mail Sorting, Storage, Transport and Distribution - Specification

All

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(MANUFACTURE - Raw Materials)	-	1000	-
5.2(MANUFACTURE - Fabric for PP tapes & for HDPE tapes)	-	1000	-
5.2- Table 1- i)("REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm")	-	1000	-
5.2- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	1000	-
5.2- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	1000	-
5.2- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	1000	-
5.2- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf) a) Lengthwise b) Widthwise)	-	1000	-
5.2- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min, N2), (kgf))	-	1000	-
5.2- Table 1- vii)("REQUIREMENTS - Elongation at break of fabric, percent: a) Lengthwise b) Widthwise")	-	1000	-
5.2- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	1000	-
5.3(Lamination)	-	1000	-
5.4(Sack Fabrication)	-	1000	-
5.5(Capacity)	-	1000	-
6.1- Table 1- i)(REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm)	-	1000	-
6.1- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	1000	-
6.1- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	1000	-
6.1- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	1000	-
6.1- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf))	-	1000	-
6.1- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min)	-	1000	-
6.1- Table 1- vii)(REQUIREMENTS - Elongation at break of fabric, percent a) Lengthwise b) Widthwise)	-	1000	-
6.1- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	1000	-
6.4(UV Resistance Test)	-	1000	-
7(PRINTING, PACKAGING AND MARKING)	-	1000	-
8(ATMOSPHERIC CONDITIONS FOR SAMPLE CONDITIONING AND TESTING)	-	1000	-
Clause 5.1(Raw Materials)	-	1000	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	1000	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	1000	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	500	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	500	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	500	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	500	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	500	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	500	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	500	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	500	-
Clause 5.4(Sack Fabrication)	-	500	-
Clause 7.3(Marking on Sacks)	-	500	-
Clause 5.1(Raw Materials)	-	500	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	500	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	500	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	500	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	500	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	500	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-

08 May, 2028

-
Included w.e.f. 24.12.2025

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

ALL

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
7.1(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	500	-
8.1.1 Table 1(Tensile Strength- IS 1608(1))	-	500	-
8.1.1 Table 1(Yield Strength- IS 1608)	-	500	-
8.1.1 Table 1(Elongation Percent- IS 1608)	-	500	-
8.2(Drift Expansion Test- IS 2335)	-	500	-
8.3(Flattening Test- IS 2328)	-	500	-
9.1 Table 2(Outside Diameter)	-	500	-
9.1 Table 2(Thickness)	-	500	-
9.1 Table 2(Mass)	-	500	-
10(Hardness)	-	0	-
13.1.1(Ovality)	-	0	-
13.1.2(Eccentricity)	-	0	-
15.1(Straightness)	-	0	-
16.1(Length)	-	0	-
17.1(Surface Protection)	-	0	-
14.0(Workmanship)	-	0	-
6.2(Fin height)	-	0	-
7.1(Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	-
7.1(Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-	0	-
8.1.1 Table 1(Tensile Strength- IS 1608(1))	-	0	-
8.1.1 Table 1(Yield Strength- IS 1608)	-	0	-
8.1.1 Table 1(Elongation Percent- IS 1608)	-	0	-
8.2(Drift Expansion Test- IS 2335)	-	0	-
8.3(Flattening Test- IS 2328)	-	0	-
9.1 Table 2(Outside Diameter)	-	0	-
9.1 Table 2(Thickness)	-	0	-
9.1 Table 2(Mass)	-	0	-
10(Hardness)	-	0	-
13.1.1(Ovality)	-	0	-
13.1.2(Eccentricity)	-	0	-
15.1(Straightness)	-	0	-
16.1(Length)	-	0	-
17.1(Surface Protection)	-	0	-

08 May, 2028

-
included w.e.f 30.01.2026

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

all

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Type A/Type B)	-	500	-
5 Table-1(Sizes Diameter of Line wire)	-	500	-
5 Table-1(Sizes Diamater of Point wire)	-	500	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	500	-
5 Table-1(Sizes Distance between two barbs)	-	500	-
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	500	-
7.1(Manufacture)	-	500	-
7.2(Manufacture)	-	500	-
7.2(Manufacture)	-	500	-
7.3(Manufacture)	-	0	-
8(CHROMATING)	-	0	-
9.1(Freedom from defects)	-	0	-
9.2(Freedom from defects)	-	0	-
9.2(Freedom from defects)	-	0	-
9.2(Freedom from defects)	-	0	-
12.1(Tensile Strength)	-	0	-
12.1(Breaking load)	-	0	-
12.2.1(Mass of zinc coating (line wire))	-	0	-
12.2.2(Mass of zinc coating (point wire))	-	0	-
12.2(Uniformity of zinc coating)	-	0	-
12.3(Ductility)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.2(Cut Angle)	-	0	-
Cl. 7.2(Length of Barbs)	-	0	-
Cl. 7.2(Finishing of Barbs)	-	0	-
Cl. 7.1(General)	-	0	-
11(Sampling)	-	0	-
13(Marking)	-	0	-
CL 05(Average dia of line wire (08))	-	0	-
CL 05(Average dia of point wire (08))	-	0	-
CL 05(Average Distance Between Two Barbs (08))	-	0	-
4(Type A/Type B)	-	0	-
5 Table-1(Sizes Diameter of Line wire)	-	0	-
5 Table-1(Sizes Diamater of Point wire)	-	0	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	0	-
5 Table-1(Sizes Distance between two barbs)	-	0	-
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	0	-
7.1(Manufacture)	-	0	-
7.2(Manufacture)	-	0	-
7.2(Manufacture)	-	0	-
7.3(Manufacture)	-	0	-
8(CHROMATING)	-	0	-
9.1(Freedom from defects)	-	0	-
9.2(Freedom from defects)	-	0	-
9.2(Freedom from defects)	-	0	-
9.2(Freedom from defects)	-	0	-
12.1(Tensile Strength)	-	0	-
12.1(Breaking load)	-	0	-
12.2.1(Mass of zinc coating (line wire))	-	0	-
12.2.2(Mass of zinc coating (point wire))	-	0	-
12.2(Uniformity of zinc coating)	-	0	-
12.3(Ductility)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.2(Cut Angle)	-	0	-
Cl. 7.2(Length of Barbs)	-	0	-
Cl. 7.2(Finishing of Barbs)	-	0	-
Cl. 7.1(General)	-	0	-
11(Sampling)	-	0	-
13(Marking)	-	0	-
CL 05(Average dia of line wire (08))	-	0	-
CL 05(Average dia of point wire (08))	-	0	-
CL 05(Average Distance Between Two Barbs (08))	-	0	-

08 May, 2028

-
included w.e.f 09-12-2025.

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

ALL

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	500	-
7.0(Dimension and Tolerances)	-	500	-
8.1 Table 1(Cu)	-	500	-
8.1 Table 1(Pb)	-	500	-
8.1 Table 1(Fe)	-	500	-
8.1 Table 1(Total other impurities excluding iron)	-	500	-
8.1 Table 1(Zn)	-	500	-
9.1 Table-2(Tensile Strength)	-	500	-
9.1 Table-2(Elongation)	-	500	-
9.2(Vickers Hardness)	-	500	-
10.1(Mercurous Nitrate Test)	-	500	-
14(Marking)	-	500	-
14(Marking)	-	0	-

08 May, 2028

-
included w.e.f 09-12-2025.

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

ALL

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	200	-
Cl 6.2(Diameter & Ovality)	-	200	-
Cl 6.2(Weight)	-	200	-
Cl 8.2(Bend test)	-	200	-
Cl 9.3(Press)	-	200	-
Cl 5.1(Workmanship)	-	200	-
Cl 6.1(Diameter)	-	200	-
Cl 6.2(Weight)	-	200	-
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	200	-
Cl 9.3(Press)	-	200	-
Cl 5.1(Workmanship)	-	200	-
Cl 6.2(Diameter & Ovality)	-	200	-
Cl 6.2(Weight)	-	200	-
Cl 8(Physical Requirements)	-	200	-
Cl 9.3(Press)	-	200	-
Clause -4, 4.3(TITANIUM)	-	200	-
Clause -4, 4.2(VANADIUM)	-	200	-
Clause -4, 4.1(NIOBIUM)	-	200	-
Clause -4, 4.1(Molybdenum)	-	200	-
Clause -4, 4.1(Chromium)	-	200	-
Clause -4, 4.1(Nickel)	-	200	-
Clause -4, 4.1( ALUMINIUM)	-	200	-
Clause -4, 4.1(SILICON)	-	200	-
Clause -4, 4.1(NITROGEN)	-	200	-
Clause -4, 4.1(MANGANESE)	-	200	-
Clause -4, 4.1(PHOSPHURS)	-	0	-
Clause -4, 4.1(SULPHUR)	-	0	-
Clause -4, 4.1( CARBON)	-	0	-
Cl. 8.1 Table 1(Elongation)	-	0	-
Cl. 8.1 Table 1(Yield Stress)	-	0	-
Clause 8.1(Elongation)	-	0	-
Clause 8.1(Yield Stress)	-	0	-
Clause 9.3(Bend test)	-	0	-
Clause 6.1(Size)	-	0	-
Cl 9.3(Press)	-	0	-
Cl 8(UTM)	-	0	-
Cl 6.2(Weight)	-	0	-
Cl 6.2(Diameter & Ovality)	-	0	-
Cl 5.1(Workmanship)	-	0	-
7(Tolerance)	-	0	-
Cl 5.1(Workmanship)	-	0	-
Cl 6.2(Diameter & Ovality)	-	0	-
Cl 6.2(Weight)	-	0	-
Cl 8(UTM)	-	0	-
Cl 9.3(Press)	-	0	-
Cl 4.1(Workmanship)	-	0	-
Cl 5 & 6(Diameter)	-	0	-
Cl 7(UTM)	-	0	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	0	-
Clause 5.1(IS 432 Part 1)	-	0	-
Clause 6.2(IS 1732)	-	0	-
Clause 8.1(IS 1608 Part 1)	-	0	-
Clause 4(Any Instrumental Method/Chemical Method)	-	0	-
Clause 4(By Calculation)	-	0	-
Clause 4(By Calculation)	-	0	-
Clause 4(Any Instrumental Method/Chemical Method)	-	0	-
Clause 5.1(Freedom from Defect)	-	0	-
Clause 6.2(Mass)	-	0	-
Clause 8.1(Ultimate Tensile Stress)	-	0	-
Clause 4(Boron)	-	0	-
Clause 4(By Calculation)	-	0	-
Clause 4(By Calculation)	-	0	-
Clause 4(Copper)	-	0	-
8.1 & 9.2(Yield Strength - IS: 1608 (P1))	-	0	-
8.1 & 9.2(Elongation on SoA 5.65mm GL - IS: 1608 (P1))	-	0	-
11(Marking)	-	0	-
Clause 5.1(Freedom from Defect)	-	0	-
Clause 6.2(Mass)	-	0	-
Clause 8.1(Ultimate Tensile Stress)	-	0	-
Clause 4(Boron)	-	0	-
Clause 4(Carbon Equivalent)	-	0	-
Clause 4(Ni+V+Ti)	-	0	-
Clause 4(Copper)	-	0	-
Clause 4(Copper)	-	0	-

08 May, 2028

-
included w.e.f 30.01.2026

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	1000	-
5(chemical composition)	-	1000	-
6.1 table 2(0.2% proof strength)	-	1000	-
6.1 table 2(tensile strength)	-	1000	-
6.1 table 2(Elongation)	-	1000	-
8(Dimensions & Tolerances)	-	1000	-
5.1, Table 1(Aluminium)	-	1000	-
5.1, Table 1(Copper)	-	1000	-
5.1, Table 1(Magnesium)	-	1000	-
5.1, Table 1(Silicon)	-	1000	-
5.1, Table 1(Iron)	-	1000	-
5.1, Table 1(Mangnese)	-	1000	-
5.1, Table 1(Zinc)	-	1000	-
5.1, Table 1(Titanium and /or other grain refining element)	-	1000	-
5.1, Table 1(Chromium)	-	1000	-
5.1, Table 1(Vanadium)	-	0	-
4(Freedom from defect)	-	0	-
5(chemical composition)	-	0	-
6.1 table 2(0.2% proof strength)	-	0	-
6.1 table 2(tensile strength)	-	0	-
6.1 table 2(Elongation)	-	0	-
8(Dimensions & Tolerances)	-	0	-
5.1, Table 1(Aluminium)	-	0	-
5.1, Table 1(Copper)	-	0	-
5.1, Table 1(Magnesium)	-	0	-
5.1, Table 1(Silicon)	-	0	-
5.1, Table 1(Iron)	-	0	-
5.1, Table 1(Mangnese)	-	0	-
5.1, Table 1(Zinc)	-	0	-
5.1, Table 1(Titanium and /or other grain refining element)	-	0	-
5.1, Table 1(Chromium)	-	0	-
5.1, Table 1(Vanadium)	-	0	-
4(Freedom from defect)	-	-	-
5(chemical composition)	-	-	-
6.1 table 2(0.2% proof strength)	-	-	-
6.1 table 2(tensile strength)	-	-	-
6.1 table 2(Elongation)	-	-	-
8(Dimensions & Tolerances)	-	-	-
5.1, Table 1(Aluminium)	-	-	-
5.1, Table 1(Copper)	-	-	-
5.1, Table 1(Magnesium)	-	-	-
5.1, Table 1(Silicon)	-	-	-
5.1, Table 1(Iron)	-	-	-
5.1, Table 1(Mangnese)	-	-	-
5.1, Table 1(Zinc)	-	-	-
5.1, Table 1(Titanium and /or other grain refining element)	-	-	-
5.1, Table 1(Chromium)	-	-	-
5.1, Table 1(Vanadium)	-	-	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 1254 (2025)

Corrugated Aluminium Sheet (Fifth Revision)

ALL

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(FREEDOM FROM DEFECTS)	-	2000	-
Cl-5(SUPPLY OF MATERIALS)	-	1500	-
Cl-6(PROFILE)	-	1000	-
Cl-7(MATERIAL)	-	1000	-
Cl-8.1(Tolerance on the thickness)	-	1000	-
Cl-8.2(Width)	-	1000	-
Cl-8.3(Length)	-	1000	-
Cl-8.4(Squareness)	-	1000	-
Cl-8.5(Depth and Pitch of the Corrugation)	-	1000	-
Cl-10(Finish)	-	1000	-
Cl-12(Marking)	-	1000	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 734 (1975)

Specification for wrought aluminium and aluminium alloy forging stock and forgings (For General Engineering Purposes) (Second Revision)

ALL

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table 1(chemical composition)	-	1000	-
5.1 table 2(0.2% proof strength)	-	1000	-
5.1 table 2(Tensile strength)	-	1000	-
5.1 table 2(Elongation)	-	1000	-
Cl.5.1(Aluminium - IS 504 and its parts or any other intrumental/chemical methods)	-	1000	-
Cl.5.1(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	1000	-
Cl.5.1(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	1000	-
Cl.5.1(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	1000	-
Cl.5.1(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	1000	-
Cl.5.1(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	1000	-
Cl.5.1(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.5.1(Titanium And/or Other Grain Refining Elements - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.5.1(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.5.1(Remarks (Cu + Mg + Si + Fe + Mn + Zn) - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
4.1(Freedom from defects)	-	0	-
9.1(Tensile test)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 18316 (2023)

HOT ROLLED AND COLD ROLLED STEEL STRIPS INTENDED FOR PROCESSING OF SEMIFULLY PROCESSED NON-GRAIN ORIENTED ELECTRICAL STEEL OR FULLY PROCESSED GRAIN ORIENTED ELECTRICAL STEEL SPECIFICATION

ALL

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 7.0(Carbon)	-	1000	-
Clause. 7.0(Silicon)	-	1000	-
Clause. 7.0(Sulphur)	-	1000	-
Clause. 7.0(Phosphorus)	-	1000	-
Clause. 7.0(Manganese)	-	1000	-
Clause. 7.0(Aluminium)	-	1000	-
Clause.8.0(Freedom From Defects)	-	1000	-
Clause.9.0(Dimensions, Shape & Tolerances (for Hot-rolled Steel))	-	2000	-
Clause.10.0(Dimensions, Shape & Tolerances (for Cold-rolled Steel))	-	2000	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 723 (2023)

Steel Countersunk Head Wire Nails ï¿½ Specification ( Second Revision )

ALL

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Dimensions & tolerances (Except 120° angle))	-	1000	-
4.2(Bend of shank)	-	1000	-
5(General requirements (Except Concentricity of head with the shank))	-	1000	-
6(Finish)	-	1000	-
7(Bend test)	-	1000	-
Cl.3(Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.3(Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.3(Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.3(Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.3(Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	1000	-
Cl.3(Aluminium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-	500	-
Cl.3(Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-	0	-
Clause. 4.3(Eccentricity)	-	0	-
Clause. 4.3(ovality)	-	0	-
Cl-4(Dimensions & Tolerances-Shank Diameter)	-	0	-
Cl-4(Dimensions & Tolerances-Head Diameter)	-	0	-
Cl-4(Dimensions & Tolerances-Length)	-	0	-
Cl-4(Approximate no of nails /kg)	-	0	-
Cl-4(Eccentricity and ovality of centre of nail head from axis of shank)	-	0	-
Cl-5(Dimensions and Tolerances Angle of Countersunk, (in°))	-	0	-
Cl-11(Marking)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 7814 (2005)

Phosphor bronze sheet, strip and foil - Specification (Second Revision)

ALL

19950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4(Supply of material)	-	2000	-
Clause 5("Freedom from defects")	-	2000	-
Clause 7(chemical composition)	-	2000	-
Clause 8.1(Tensile test)	-	2000	-
Clause 8.2(Bend Test)	-	2000	-
Clause 9.1("Diameter of Strip and Foil")	-	2000	-
Clause 9.2(Thickness Tolerances)	-	2000	-
Clause 9.3(Width Tolerance)	-	2000	-
Clause 9.4("Length Tolerance for Sheet")	-	2000	-
Clause 9.5("Permissible Maximum Value on Camber for Strip")	-	2000	-
Clause 10("Sampling and criteria for conformity")	-	1950	-
Clause 13(Marking)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 5484 (2023)

EC GRADE ALUMINIUM ROD PRODUCED BY CONTINUOUS CASTING AND ROLLING - SPECIFICATION

ALL

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Manufacture)	-	1000	-
Cl-6.1(Grades and chemical composition of EC grade aluminium rod produced)	-	1000	-
Cl-6.2(Chemical analysis of the material)	-	1000	-
Cl-7.1(General condition for delivery and inspection relating)	-	1000	-
Cl-9(Ultimate tensile strength and elongation)	-	1000	-
Cl-10.1(Resistivity)	-	1000	-
Cl-10.1(electrical conductivity)	-	1000	-
Cl-10.1.1(Resistivity and Conductivity Limit)	-	1000	-
Cl-11(Dimensions)	-	1000	-
Cl-13(Finish and freedom from defects)	-	1000	-
Cl-14(Rejection and retest)	-	0	-
Cl-16(Marking)	-	0	-
CL 9(ULTIMATE TENSILE STRENGTH AND ELONGATION)	-	0	-
CL 11(DIMENSIONS)	-	0	-
CL 13(FINISH AND FREEDOM FROM DEFECTS)	-	0	-
9(Elongation)	-	0	-
12(Joint)	-	0	-
Cl.6.1 as per IS 4026(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Copper - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Magnesium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Zinc - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.6.1 as per IS 4026(Titanium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 12425 (2022)

SPECIFICATION FOR STEEPLECHASE HURDLES First Revision

ALL

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.2(Top Bar)	-	2500	-
Cl.2.1(Dimension)	-	2500	-
Cl.2.2(Mass)	-	2500	-
Cl.3(Packing and Marking)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 4508 (2024)

OPEN ENDED SLUGGING WRENCHES ( SPANNERS ) - SPECIFICATION ( Second Revision )

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimensions)	-	1000	-
Clause.4.0(Carbon)	-	1000	-
Clause.4.0(Sulphur)	-	1000	-
Clause.4.0(Phosphorus)	-	1000	-
Clause.4.0(Nickel)	-	1000	-
Clause.4.0(Molybdenum)	-	1000	-
Clause.4.0(Chromium)	-	1000	-
Clause.4.0(Silicon)	-	1000	-
Clause.4.0(Manganese)	-	1000	-
Clause.5.0(Hardness)	-	1000	-
Clause.6.0(Manufacture,Workmanship & finish)	-	1000	-
Clause.7.0(Preservation & packing)	-	1000	-
Clause.8.0(Sampling)	-	1000	-
Clause.9.0(Designation)	-	1000	-
Clause.10.0(Marking)	-	1000	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 1673 (1984)

Spectfication for mild steel wire, cold heading quality (Second Revision)

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 5.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 5.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 5.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 5.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
6(FREEDOM FROM DEFECTS)	-	2000	-
7.1(i)Ultimate Tensile Strength,)	-	2000	-
7.2(ii) Reverse Torsion Test)	-	2000	-
7.3(iii) Crushing Test)	-	2000	-
8( DIMENSIONS AND TOLERANCES)	-	2000	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Sulphur -IS 228 or method specified in relevant ISO standard)	-	2000	-
Cl.4(Phosphorus -IS 228 or method specified in relevant ISO standard)	-	2000	-
5.2(Tensile Test-1608:Part 1)	-	2000	-
5.2(Tensile Strength, Mpa)	-	2000	-
5.2(Elongation, %)	-	2000	-
5.3(Bend Test-1599)	-	1000	-
7.1(Freedom from defects)	-	1000	-
8.2(Width)	-	1000	-
8.2(Thickness)	-	1000	-
9.1(Finishing & Packing)	-	1000	-
10(Marking)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 2385 (1977)

Specification for hot - Rolled mild steel sheet and strip in coil form for cold - Reduced tinplate and cold - Reduced blackplate (First Revision)

ALL

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.1, 5.2 & Table1(Carbon- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Manganese- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Sulphur- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Phosphorus- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Nitrogen- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5.1, 5.2 & Table1(Aluminium- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	500	-
6(Freedom from defects)	-	500	-
8(Dimensions and Tolerances)	-	500	-
Cl. 5.1, 5.2(chromium)	-	500	-
Cl. 5.1, 5.2(silicon)	-	500	-
Cl. 5.1, 5.2(copper)	-	500	-
Cl. 5.1, 5.2(aluminium)	-	500	-
Cl. 5.1, 5.2(Nitrogen )	-	500	-
Cl. 5.1, 5.2(Phosphorus)	-	500	-
Cl. 5.1, 5.2(Sulphur)	-	1000	-
Cl. 5.1, 5.2(Manganese)	-	1000	-
Cl. 5.1, 5.2(carbon)	-	1000	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

ALL

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1, 8.1.1 & 10.1 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
6(Freedom From Defects)	-	500	-
9.3(Tensile Test-1608:Part 1)	-	500	-
9.3, Table 3 (Yield Strength, Mpa)	-	500	-
9.3, Table 3 (Tensile Strength, Mpa)	-	500	-
9.3, Table 3 (Elongation, %)	-	500	-
9.4(Erichsen Cupping Test,(Average depth of cupping) mm)	-	500	-
11(Surface finish)	-	500	-
12(Dimensions)	-	500	-
14.1(Thickness,mm)	-	500	-
14.2( Width, mm)	-	500	-
14.3(Length, mm)	-	500	-
14.4(Flatness, mm)	-	0	-
14.5(Camber, mm)	-	0	-
Clause 9.1, 9.2 & Table 3(IS 1608 Part 1)	-	0	-
17(Marking)	-	0	-
Clause 9.1, 9.2 & Table 3(0.2 Percent Yield Strength)	-	0	-
4.1(General requirements)	-	0	-
6(Freedom from defects)	-	0	-
7(Heat treatment)	-	0	-
8.1, table 1(C Si Mn Ni Cr S P Cu Ni)	-	0	-
8.1.1, table 2(Carbon Silicon Manganese Nickel Chromium Sulphur Phosphorus Copper Nitrogen)	-	0	-
9.1(Sample plan)	-	0	-
9.2(Tensile test)	-	0	-
9.3(Mechanical properties)	-	0	-
9.4(Erichsen cupping test)	-	0	-
10(Retests)	-	0	-
11(Surface finish)	-	0	-
12(Dimensions)	-	0	-
13(Edge condition)	-	0	-
14.1(Thickness)	-	0	-
14.2.1(Mill Edge)	-	0	-
14.2.2(Trimmed Edge)	-	0	-
14.3(Length)	-	0	-
14.4(Flatness)	-	0	-
14.5(Camber)	-	0	-
15(Inspection)	-	0	-
17(Marking)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 2721 (2003)

Galvanized steel chain link fence fabric - Specification (Second Revision)

ALL

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.5(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.6.1, 6.2, Table 1(Mesh Size)	-	500	-
Cl.6.3, Table 1(Width of the fabric)	-	500	-
Cl.6.3, Table 1(Length of the fabric)	-	500	-
Cl.6.1, 6.2, Table 1(Nominal Dia of Mesh wire)	-	0	-
Cl. 7.2 and Table 1(Line Wire (Diameter))	-	0	-
Cl. 7.2 and Table 1(Line Wire (Number of wires))	-	0	-
Cl.8(Chain link fence fabric(Mass of zinc coating)- IS 6745)	-	0	-
Cl.8(Chain link fence fabric (Number of dips of zinc coating))	-	0	-
Cl.8(Chain link fence fabric (Uniformity of Zinc coating)-IS 2633)	-	0	-
Cl.8(Chain link fence fabric [Adhesion test of Zinc coating (Minimum complete turn of wrap)]- IS 4826/IS 12753)	-	0	-
Cl.8(Chain link fence fabric [Adhesion test of Zinc coating( Ratio between mandrel diameter and of wire)]-IS 4826/IS 12753)	-	0	-
Cl.9.1.1(Tensile test of mesh and line wires- IS 1608)	-	0	-
Cl.9.1.2(Wrapping test of mesh and line wires-IS 1755)	-	0	-
Cl.9.1.3(Twist test of mesh and line wires-IS 1717)	-	0	-
Cl.9.1.4(Bend test of mesh and line wires- IS 1608)	-	0	-
Cl.9.2(Line wire (Mass of zinc coating)- IS 6745)	-	0	-
Cl.9.2(Line Wire (Number of dips of zinc coating))	-	0	-
Cl.9.2(Line Wire (Uniformity of Zinc coating)-IS 2633)	-	0	-
Cl.9.2(Line Wire [Adhesion test of Zinc coating (Minimum complete turn of wrap)]- IS 4826/IS 12753)	-	0	-
Cl.9.2(Line Wire [Adhesion test of Zinc coating( Ratio between mandrel diameter and of wire)]-IS 4826/IS 12753)	-	0	-
Cl.9.2(Mesh wire (Mass of zinc coating)- IS 6745)	-	0	-
Cl.9.2(Mesh Wire (Number of dips of zinc coating))	-	0	-
Cl.9.2(Mesh Wire (Uniformity of Zinc coating)-IS 2633)	-	0	-
Cl.9.2(Mesh Wire [Adhesion test of Zinc coating (Minimum complete turn of wrap)]- IS 4826/IS 12753)	-	0	-
Cl.9.2(Mesh Wire [Adhesion test of Zinc coating( Ratio between mandrel diameter and of wire)]-IS 4826/IS 12753)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 5082 (1998)

Wrought aluminium and aluminium alloy bars, rods, tubes, sections, plates and sheets for electrical applications (Second Revision)

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(CHEMICAL COMPOSITION Table 1)	-	1000	-
Clause 5(FREEDOM FROM DEFECTS)	-	1000	-
8.1(MECHANICAL TEST Tensile Strength Min, Mpa)	-	1000	-
8.1(MECHANICAL TEST (0.2 Percent Proof Stress Min, Mpa))	-	1000	-
8.1(Percent Elongation on 5.65 Min)	-	1000	-
8.1(Electrical Conductivity at 20°C,Min)	-	1000	-
8.1(Maximum Electrical Resistivity at 20°C ohm-mm/mm2)	-	1000	-
8.2(Bend Test)	-	1000	-
Clause 10(DIMENSIONAL TOLERANCES)	-	1000	-
6.1, Table 1(Aluminium)	-	1000	-
6.1, Table 1(Copper)	-	1000	-
6.1, Table 1(Magnesium)	-	1000	-
6.1, Table 1(Silicon)	-	1000	-
6.1, Table 1(Manganese)	-	1000	-
6.1, Table 1(Zinc)	-	1000	-
6.1, Table 1(Titanium)	-	0	-
6.1, Table 1(Chromium)	-	0	-
6.1, Table 1(Iron)	-	0	-
6.1, Table 1(Vanadium)	-	0	-
6.1(CHEMICAL COMPOSITION Table 1)	-	0	-
Clause 5(FREEDOM FROM DEFECTS)	-	0	-
8.1(MECHANICAL TEST Tensile Strength Min, Mpa)	-	0	-
8.1(MECHANICAL TEST (0.2 Percent Proof Stress Min, Mpa))	-	0	-
8.1(Percent Elongation on 5.65 Min)	-	0	-
8.1(Electrical Conductivity at 20°C,Min)	-	0	-
8.1(Maximum Electrical Resistivity at 20°C ohm-mm/mm2)	-	0	-
8.2(Bend Test)	-	0	-
Clause 10(DIMENSIONAL TOLERANCES)	-	0	-
6.1, Table 1(Aluminium)	-	0	-
6.1, Table 1(Copper)	-	0	-
6.1, Table 1(Magnesium)	-	0	-
6.1, Table 1(Silicon)	-	0	-
6.1, Table 1(Manganese)	-	0	-
6.1, Table 1(Zinc)	-	0	-
6.1, Table 1(Titanium)	-	0	-
6.1, Table 1(Chromium)	-	0	-
6.1, Table 1(Iron)	-	0	-
6.1, Table 1(Vanadium)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 737 (2024)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES SPECIFICATION (Fifth Revision)

all

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Ordering Information - IS 737)	-	500	-
Cl. 4 (a)(Grade/ Thickness - IS 737)	-	500	-
Cl. 4 (b)(Condition - IS 737)	-	500	-
Cl. 4 (c)(Quantity in Kg - IS 737)	-	500	-
Cl. 4 (d)(Size - Thickness X Width X Length (T X W X L) in mm for sheets and (T X W) in mm for Strips/ Coils - IS 737)	-	500	-
Cl. 4 (e)(Coil ID and Coil Weight for Strips/ Coils - IS 737)	-	500	-
Cl. 4 (f)(Core/ Spool Requirement for Coils - IS 737)	-	500	-
Cl. 4 (g)(Packing Mode - IS 737)	-	500	-
Cl. 5(Supply for Material - IS 737/ IS 10259)	-	500	-
Cl. 6(Freedom from Defects - IS 737)	-	500	-
Cl. 7(Chemical Composition - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Si - IS 504 (Part-1)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Fe - IS 504 (Part-2)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Cu - IS 504 (Part-3)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Mn - IS 504 (Part-5)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Mg - IS 504 (Part-6)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Cr - IS 504 (Part-8)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Zn - IS 504 (Part-4)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Ti - IS 504 (Part-11)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Others (Each) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	500	-
Cl. 7(Others (Total) - IS 504/ IS 504 (Part-1 to 12)/ IS 504 (Part-13 to 16)/ ASTM E 1251/ IS 11035)	-	0	-
Cl. 7(Al - IS 504)	-	0	-
Cl. 8(Mechanical Properties - IS 1608 (Part-1))	-	0	-
Cl. 8.1(0.2% Proof Stress - IS 1608 (Part-1))	-	0	-
Cl. 8.1(Tensile Strength - IS 1608 (Part-1))	-	0	-
Cl. 8.1(Elongation on 50mm Gauge Length - IS 1608 (Part-1))	-	0	-
Cl. 8.2(Bend Test - IS 1599)	-	0	-
Cl. 9(Condition - IS 737/ IS 5052)	-	0	-
Cl. 10(Dimensions and Tolerances - IS 737/ IS 2676)	-	0	-
Cl. 11(Selection of Test Samples - IS 737)	-	0	-
Cl. 11.1(Sheet and Strip of Aluminium or Non - Heat Treatable Aluminium Alloy - IS 737)	-	0	-
Cl. 11.2(Sheet and Strip of Heat - Treatable Aluminium Alloys - IS 737)	-	0	-
Cl. 12(Retests - IS 737/ IS 10259)	-	0	-
Cl. 13(Packaging - IS 737/ IS 10259)	-	0	-
Cl. 13.1(Marking - IS 737)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 613 (2000)

Copper rods and bars for electrical purposes - Specification (Third Revision)

ALL

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause no.3(SUPPLY OF MATERIAL)	-	500	-
Clause no.6(FREEDOM FROM DEFECTS)	-	500	-
Clause no.7(CONDITION OF SUPPLY)	-	500	-
Clause no.8(CHEMICAL COMPOSITION)	-	500	-
Clause no.9.1, table no,1(" tensile test ")	-	500	-
Clause no.9.2(Bend test)	-	1000	-
"Clause no.10.1 and 11.1.1 Table No. 2"(Dimensions and Tolerances)	-	1000	-
"Clause no.10.2 and Table No. 3"("Tolerances on Length of Bar Rod in Straight Length ")	-	1000	-
"Clause no.10.4 and Table No. 4"(Corner Radius and Tolerances)	-	1000	-
"Clause no.11 and Table No. 5"(Electrical Resistivity)	-	1000	-
Clause no. 13(packing)	-	1000	-
Clause no. 14(Marking)	-	1000	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 15961 (2025)

Hot Dip Aluminium-Zinc Alloy Metallic Coated Steel Strip and Sheet - Specification (First Revision)

ALL

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.5(Surface Finish)	-	500	-
Cl-4(Supply of Material - General requirements)	-	500	-
Cl-5(Manufacture)	-	500	-
Cl-7(C)	-	500	-
Cl-7(Mn)	-	500	-
Cl-7(S)	-	500	-
Cl-7(P)	-	500	-
Cl-7(Total aluminium)	-	500	-
Cl-7(silicon)	-	500	-
Cl-7(Nitrogen)	-	500	-
Cl-7(Chromium,)	-	500	-
Cl-7(Nickel,)	-	500	-
Cl-7(Niobium,)	-	500	-
Cl-7(Vanadium,)	-	500	-
Cl-7(Titanium,)	-	500	-
Cl-7(Molybdenum,)	-	500	-
Cl-7(Boron,)	-	500	-
Cl-7(Calcium)	-	0	-
Cl-7(others,)	-	0	-
Cl-7(Phosphorus)	-	0	-
Cl-8.1(Test Piece)	-	0	-
Cl-8.2(Testing Frequency)	-	0	-
Cl-8.3, Table-1(Yield Strength)	-	0	-
Cl-8.3, Table-1(Tensile Strength)	-	0	-
Cl-8.3, Table-1(Elongation,)	-	0	-
Cl-9(Coating Test)	-	0	-
Cl-9.1, Table-2(Minimum Coating Mass (Total Both Surfaces)- Triple Spot)	-	0	-
Cl-9.1, Table-2(Minimum Coating Mass (Total Both Surfaces)- Single Spot)	-	0	-
Cl-9.1, Table-2(Minimum Coating Mass (One Surface) -Single Spot)	-	0	-
Cl-9.4(Single Spot Coating Mass)	-	0	-
Cl-9.5(Triple Spot Coating Mass)	-	0	-
Cl-9.6(Differential Coating)	-	0	-
Cl-10(Coating Adhesion Test)	-	0	-
Cl-11(Freedom From Defects)	-	0	-
Cl-12(Mass)	-	0	-
Cl-13.1(Coil Internal Diameter)	-	0	-
Cl-13.2(Length Tolerance)	-	0	-
Cl-13.3(Width Tolerance)	-	0	-
Cl-13.4(Thickness Tolerance)	-	0	-
Cl-13.5(Camber)	-	0	-
Cl-13.6(Deviation from Squareness (Out-of Square))	-	0	-
Cl-13.7(Deviation from Flatness (Steepness))	-	0	-
Cl-13.8(Profiled Sheets)	-	0	-
Cl-16(Marking)	-	0	-

08 May, 2028

-
Included w.e.f 31.12.2025

IS 15834 (2020)

Stainless Steel Sliding Door Bolts ( Aldrops ) for Use With Padlocks - Specification ( First Revision )

ALL

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	500	-
Cl 6(MANUFACTURE)	-	500	-
Cl 7(FINISH)	-	500	-
5(DIMENSIONS AND TOLERANCES)	-	500	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
6(MANUFACTURE)	-	0	-
7(FINISH)	-	0	-
8(Marking)	-	0	-
8(Marking)	-	0	-
Cl.4(Carbon)	-	0	-
Cl.4(Sulphur)	-	0	-
Cl.4(Phosphorus)	-	0	-
Cl.4(Manganese)	-	0	-
Cl.4(Silicon)	-	0	-
Cl.4(Nickel)	-	0	-
Cl.4(Chromium)	-	0	-
Cl.4(Copper)	-	0	-
Cl.4(Molybdenum)	-	0	-
Cl.4(Nitrogen)	-	0	-
Cl.4(Titanium)	-	0	-
Cl.4(Niobium)	-	0	-
Sub-Clause. 10.3.1(Dimension)	-	0	-
Sub-Clause. 10.3.2(Tensile test)	-	0	-
Sub-Clause. 10.3.3(corrosion resistance)	-	0	-

08 May, 2028

-
Included w.e.f 18.11.2025

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

ALL

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about X-X))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about Y-Y))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus about X-X))	-	0	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Plastic Modulus about Y-Y))	-	0	-
Cl. 10.1, 14.1, 18.1(Straightness)	-	0	-
Cl. 10.2, Fig 1(Outside dimension (B))	-	0	-
Cl. 10.2, Fig 1(Outside dimension (H))	-	0	-
Cl. 10.2, Fig 1(Outside dimension (T))	-	0	-
Cl. 10.4, Fig 2(Concavity, X1)	-	0	-
Cl. 10.4, Fig 2(Convexity, X2)	-	0	-
Cl. 10.5, Fig 3(Squareness of side)	-	0	-
Cl. 10.6, Fig 4(External Corner Radius)	-	0	-
Cl. 10.7, Fig 5(Total twist, V)	-	0	-
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	0	-
Cl. 15.2, Table 3(Yield Strength- IS 1608)	-	0	-
Cl. 15.2, Table 3(Elongation- IS 1608)	-	0	-
Cl. 14.1(Exact Length)	-	0	-
Cl. 14.1(Random Length)	-	0	-
Cl. 14.1(Weight on individual length)	-	0	-
Cl. 14.1(Weight on lots of 10 tonnes min)	-	0	-
Cl. 18, Note 2(Internal Fin Height (Only for Cold Formed))	-	0	-
7(Micro Alloying elements(Nb+V+Ti))	-	0	-
7(Carbon equivalent as CE)	-	0	-
10.4(Concavity/Convexity-SOP MT-23)	-	0	-
10.5(Squareness of corner/Sides-SOP MT-23)	-	0	-
10.6("External corner Radius/ Radii of corners-outside - SOP MT-23")	-	0	-
11(Oiling & Painting - IS 4923)	-	0	-
18.1(Height of the internal weld fin - IS 4923)	-	0	-
10.3(Thickness - IS 4923)	-	0	-
13(Marking)	-	0	-
Cl-19(Mechanical Tests)	-	0	-
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about X-X))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about Y-Y))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus about X-X))	-	-	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Plastic Modulus about Y-Y))	-	-	-
Cl. 10.1, 14.1, 18.1(Straightness)	-	-	-
Cl. 10.2, Fig 1(Outside dimension (B))	-	-	-
Cl. 10.2, Fig 1(Outside dimension (H))	-	-	-
Cl. 10.2, Fig 1(Outside dimension (T))	-	-	-
Cl. 10.4, Fig 2(Concavity, X1)	-	-	-
Cl. 10.4, Fig 2(Convexity, X2)	-	-	-
Cl. 10.5, Fig 3(Squareness of side)	-	-	-
Cl. 10.6, Fig 4(External Corner Radius)	-	-	-
Cl. 10.7, Fig 5(Total twist, V)	-	-	-
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	-	-
Cl. 15.2, Table 3(Yield Strength- IS 1608)	-	-	-
Cl. 15.2, Table 3(Elongation- IS 1608)	-	-	-
Cl. 14.1(Exact Length)	-	-	-
Cl. 14.1(Random Length)	-	-	-
Cl. 14.1(Weight on individual length)	-	-	-
Cl. 14.1(Weight on lots of 10 tonnes min)	-	-	-
Cl. 18, Note 2(Internal Fin Height (Only for Cold Formed))	-	-	-
7(Micro Alloying elements(Nb+V+Ti))	-	-	-
7(Carbon equivalent as CE)	-	-	-
10.4(Concavity/Convexity-SOP MT-23)	-	-	-
10.5(Squareness of corner/Sides-SOP MT-23)	-	-	-
10.6("External corner Radius/ Radii of corners-outside - SOP MT-23")	-	-	-
11(Oiling & Painting - IS 4923)	-	-	-
18.1(Height of the internal weld fin - IS 4923)	-	-	-
10.3(Thickness - IS 4923)	-	-	-
13(Marking)	-	-	-
Cl-19(Mechanical Tests)	-	-	-

08 May, 2028

-
Included w.e.f 18.11.2025

IS 16242 : Part 1 (2025)

Uninterruptible power systems UPS Part 1 Safety requirements (first revision)

72000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Fault and abnormal conditions)	-	72000	-
Cl-4.3(Short-circuit and overload protection)	-	72000	-
Cl-4.3.101(AC input current)	-	72000	-
Cl-4.3.102(Transformer protection)	-	72000	-
Cl-4.3.103(AC input short-circuit current)	-	72000	-
Cl-4.3.104(Protection of the energy storage device)	-	72000	-
Cl-4.3.105(Unsynchronised load transfer)	-	72000	-
Cl-4.4(Protection against electric shock)	-	72000	-
Cl-4.4.2.2.2(Selection tables for contact area and skin humidity condition)	-	72000	-
Cl-4.4.3.3(Protection by means of enclosures or barriers- Openings)	-	72000	-
Cl-4.4.7.1.1(Influencing factors)	-	72000	-
Cl-4.4.7.1.2(Pollution degree)	-	72000	-
Cl-4.4.7.1.3(Overvoltage category (OVC))	-	72000	-
Cl-4.4.7.7(PWB spacings for functional insulation)	-	72000	-
Cl-4.4.9(Capacitor discharge)	-	72000	-
Cl-4.5.2(Service access areas)	-	72000	-
Cl-4.6(Protection against fire and thermal hazards)	-	72000	-
Cl-4.6.2.2(Components within a circuit representing a fire hazard)	-	72000	-
Cl-4.6.3.1(General)	-	72000	-
Cl-4.6.3.2(Flammability of enclosure materials)	-	72000	-
Cl-4.6.3.3.2(Openings in the top and side of fire enclosures)	-	72000	-
Cl-4.6.4.1(Temperature limits- Internal parts)	-	72000	-
Cl- 4.6.5(Limited power sources)	-	72000	-
Cl-4.7(Protection against mechanical hazards)	-	72000	-
Clause 4(Protection against hazards)	-	72000	-
Cl-4.7.101(Protection in service access area)	-	72000	-
Clause 5(Test requirements)	-	72000	-
Cl-4.8 .101(Equipment with multiple sources of supply- General)	-	72000	-
Clause 5.2.2(Mechanical tests)	-	72000	-
Clause 5.2.3(Electrical tests)	-	72000	-
Cl-4.9(Protection against environmental stresses)	-	72000	-
Cl-4.10(Protection against sonic pressure hazards)	-	72000	-
Clause 5.2.4("Abnormal operation tests")	-	72000	-
Cl-4.11(Wiring and connections)	-	72000	-
Clause 5.2.5(Material tests)	-	72000	-
Clause 5.2.6(Environmental tests)	-	72000	-
Cl-4.11.101.1(Non-detachable cords- Cord guard)	-	72000	-
Clause 5.2.7(Hydrostatic pressure test)	-	72000	-
Cl-4.11.101.2(Cord anchorages and strain relief)	-	72000	-
Clause 6(Information and marking requirements)	-	72000	-
Cl-4.101.1(Emergency switching (disconnect) device)	-	72000	-
Clause 6.1.101(Durability)	-	72000	-
Cl-4.101.2(Normal disconnect devices)	-	72000	-
Cl-4.102.1(Stored energy source- General)	-	72000	-
Cl-4.102.2(Accessibility and maintainability)	-	72000	-
Cl-4.102.3(Distance between battery cells)	-	72000	-
Cl- 4.102.5(Electrolyte spillage)	-	72000	-
Cl- 4.102.6(Ventilation and hydrogen concentration)	-	72000	-
Cl- 4.102.8.1(Overcurrent and earth fault protection)	-	72000	-
Cl- 4.102.8.2(Location of protective devices)	-	72000	-
Cl-4.102.8.3(Rating of protective devices)	-	72000	-
Cl-4.103(UPS connection to telecommunication lines)	-	72000	-
Cl-5.1.5.3(Operating parameters for tests)	-	72000	-
Cl-5.1.7(Test overview)	-	72000	-
Cl-5.2.2.2(Non-accessibility test)	-	72000	-
Cl-5.2.2.4.4(Drop test)	-	72000	-
Cl-4.8.102(Backfeed protection)	-	72000	-
Cl- 4.102.7(Charging voltages)	-	72000	-
Cl-5.2.2.6.101(Wall or ceiling mounted equipment test)	-	72000	-
Cl-5.2.2.6.102(Rack mounted equipment test)	-	72000	-
Cl-5.2.2.101(Cord guard test)	-	72000	-
Cl-5.2.3.9(Limited power source test)	-	72000	-
Cl-5.2.3.10(Temperature rise test)	-	72000	-
Cl-5.2.3.101.1(Backfeed protection test- General)	-	72000	-
Cl-5.2.3.101.2(Test for pluggable UPS)	-	72000	-
Cl-5.2.3.101.3(Test for permanently connected UPS)	-	72000	-
Cl-5.2.3.101.4(Method to simulate the load-induced change of reference potential for pluggable UPS)	-	72000	-
Cl-5.2.3.101.5(Solid-state backfeed protection)	-	72000	-
Cl-5.2.3.102(Input current test)	-	72000	-
Cl-5.2.3.103(Short-time withstand current test)	-	72000	-
Cl-5.2.3103.3(Input port short-time withstand current rating)	-	72000	-
Cl-5.2.3.104(Transformer protection test)	-	72000	-
Cl- 5.2.3.105(Unsynchronised load transfer test)	-	72000	-
Cl-5.2.4.1(Abnormal operation and simulated faults tests- General)	-	72000	-
Cl-5.2.6.4(Vibration test)	-	72000	-
Cl-5.2.6.5(Salt mist test)	-	72000	-
Cl-5.2.6.6(Dust and sand test)	-	72000	-
Cl-6(Information and marking requirements)	-	72000	-

08 May, 2028

-
-

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.2, Table 3(Tensile Test-1608:Part 1)	-	400	-
8.2, Table 3(Proof Stress, N/mm2)	-	400	-
8.2, Table 3(Tensile Strength, N/mm2)	-	400	-
8.2, Table 3(Elongation, %)	-	400	-
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	-
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	400	-
8.4(Bend Test)	-	400	-
8.5(Erichsen Cupping Test)	-	400	-
10.1(Thickness, mm)	-	500	-
10.2(width, mm)	-	500	-
10.3(Length, mm)	-	500	-
10.4(Flatness,mm)	-	500	-
10.5(Camber, mm)	-	500	-
11(Surface Finish)	-	500	-
Cl . 6 .0(Freedom from defect)	-	500	-
13(Marking)	-	0	-
8.2, Table 3(Tensile Test-1608:Part 1)	-	0	-
8.2, Table 3(Proof Stress, N/mm2)	-	0	-
8.2, Table 3(Tensile Strength, N/mm2)	-	0	-
8.2, Table 3(Elongation, %)	-	0	-
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	0	-
8.4(Bend Test)	-	0	-
8.5(Erichsen Cupping Test)	-	0	-
10.1(Thickness, mm)	-	0	-
10.2(width, mm)	-	0	-
10.3(Length, mm)	-	0	-
10.4(Flatness,mm)	-	0	-
10.5(Camber, mm)	-	0	-
11(Surface Finish)	-	0	-
Cl . 6 .0(Freedom from defect)	-	0	-
13(Marking)	-	0	-

08 May, 2028

-
included w.e.f 09-12-2025.

IS 15354 : Part 1 (2023)

Single-use medical examination gloves Part 1 Specification for gloves made from rubber latex or rubber solution Second Revision

ALL

9900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.3(Finish)	-	0	-
Cl-7.1, Table-2(Size code)	-	500	-
Cl-7.1, Table-2(Width corresponding to size code (dimension w, Figure 1))	-	500	-
Cl-7.1, Table-2(Descriptive size)	-	500	-
Cl-7.1, Table-2(Width corresponding to descriptive size (dimension w, Figure 1))	-	500	-
Cl-7.1, Table-2(Minimum length (dimension l, Figure 1))	-	500	-
Cl-7.1, Table-2(Minimum thickness (at locations shown in Figure 1))	-	1000	-
Cl-7.1, Table-2(Maximum thickness (at approximate centre of palm))	-	2100	-
Cl-7.2(Water tightness)	-	1000	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum force at break before accelerated ageing, N)	-	1000	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum elongation at break before accelerated ageing, %)	-	500	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum force at break after accelerated ageing, N)	-	500	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum elongation at break after accelerated ageing, %)	-	500	-
Cl-7.4(Sterility)	-	0	-
Cl-9(Marking)	-	0	-
Cl-5(Materials)	-	500	-

08 May, 2028

-
Included w.e.f 06.11.2025 Exclusion: Cl-7.4 (Sterility)

IS 11951 (2024)

PUMPSET FOR DIRECT EVAPORATIVE AIR COOLER â SPECIFICATION (Second Revision)

47000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Non-Submersible Pumpset)	-	47000	-
5.1.2(Submersible Pumpset)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Discharge Head, m)	-	47000	-
6.1, 7.3, 9.1, 9.4.2,Table-1(Minimum Discharge, l/min)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 1 Motor Wattage)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 2 Motor Wattage)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Motor Wattage)	-	47000	-
6.1, 7.3, 9.1,9.4.2, Table-2(Minimum Discharge Head, Hd)	-	47000	-
6.1, 7.3, 9.1, 9.4.2,Table-2(Discharge Measurement Height, h)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Minimum, Discharge*)	-	47000	-
Cl-8(GENERAL REQUIREMENTS)	-	47000	-
9.2(Tests on motor)	-	47000	-
9.3(Water Requirement)	-	47000	-
9.4.1(Reliability Tests)	-	47000	-
9.4.3(Ingress protection test)	-	47000	-
9.4.6(Dry Run Test)	-	47000	-
9.5(Routine Test)	-	47000	-
9.6(Type Test)	-	47000	-
9.7(Leakage current and electric strength at operating temperature)	-	47000	-
9.7(Moisture resistance)	-	47000	-
9.7(Leakage current and electric strength)	-	47000	-
5.1.1(Non-Submersible Pumpset)	-	47000	-
5.1.2(Submersible Pumpset)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Discharge Head, m)	-	47000	-
6.1, 7.3, 9.1, 9.4.2,Table-1(Minimum Discharge, l/min)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 1 Motor Wattage)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 2 Motor Wattage)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Motor Wattage)	-	47000	-
6.1, 7.3, 9.1,9.4.2, Table-2(Minimum Discharge Head, Hd)	-	47000	-
6.1, 7.3, 9.1, 9.4.2,Table-2(Discharge Measurement Height, h)	-	47000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Minimum, Discharge*)	-	47000	-
Cl-8(GENERAL REQUIREMENTS)	-	47000	-
9.2(Tests on motor)	-	47000	-
9.3(Water Requirement)	-	47000	-
9.4.1(Reliability Tests)	-	47000	-
9.4.3(Ingress protection test)	-	47000	-
9.4.6(Dry Run Test)	-	47000	-
9.5(Routine Test)	-	47000	-
9.6(Type Test)	-	47000	-
9.7(Leakage current and electric strength at operating temperature)	-	47000	-
9.7(Moisture resistance)	-	47000	-
9.7(Leakage current and electric strength)	-	47000	-

08 May, 2028

-
included w.e.f 09-12-2025.

IS 1475 (2024)

Drinking Water Coolers - Specification (Fourth Revision)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	50000	-
5(Construction)	-	50000	-
6.3(Cooling Capacity Test)	-	50000	-
6.4(Maximum Operating Condition Test)	-	50000	-
6.5(Pull Down Test)	-	50000	-
9(Maximum Power Consumption Test)	-	50000	-
10(Annual Energy Consumption Test)	-	50000	-
11(Storage Capacity Test)	-	50000	-
13(Functional Test)	-	50000	-
14 a)(Protection against electric shock)	-	50000	-
14 b)(High voltage (electric strength) test)	-	50000	-
14 c)(Leakage current tests)	-	50000	-
14 d)(Provision for earthing)	-	50000	-

08 May, 2028

-
Included w.e.f. 29.10.2025

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

ALPHA TEST HOUSE PVT LTD, BAHADURGARH

198-199, MIE, Industrial Area, Phase-1, Bahadurgarh, Haryana, Bahadurgarh, Jhajjar, Haryana, 124507

9818233966 info@alphatesthouse.com

Scope List