BIS - LIMS (Laboratory Information Management System)

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY(CIPET) : IPT-BHUBANESWAR

B/25, C.N.I complex, Patia, Bhubaneswar, BHUBANESWAR, Khordha, Odisha, 751024

7566177001 cipetbbsr@gmail.com

Scope List

Reset

88 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 10151 (2019)

Polyvinyl chloride (Pvc) and its copolymers for its safe use in contact with foodstuffs, pharmaceuticals and drinking water - Specification (First Revision)

Polyvinyl Chloride (PVC) and its Copolymers for its Saf

4150.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.4(Monomer content)	-	4150.00		NIL

Complete

31 Dec, 2023

IS 17358 : Part 2 (2020)

Agro textiles â€“ Fencing nets for agriculture and horticulture purposes â€“ Specification Part 2 Fencing nets made from mono filament yarns and combination of tape and mono filament yarns

Agro Textiles-Fencing Nets for Agriculture and Horticul

19135.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 4.1(HDPE Monofilament density)	-	250.00	NIL
Clause No. 4.1.1(Heat Shrinkage of the Monofilament Yarn at 60 and 95℃)	-	700.00	NIL
Clause No. 4.2(Width of the tape used in fabric)	-	250.00	NIL
Clause No. 5.1(Width of the Fabric)	-	249.98	NIL
Clause No. 5.2.1(Eyelet to Eyelet Edge Distance)	-	249.99	NIL
Clause No. 6(Mass of the fencing nets)	-	249.98	NIL
Clause 7.1(Dimensions)	-	500.00	NIL
Clause 7.2 (ii)(Average breaking strength of wind shield net fabric (Strip method, 325×50 mm test piece with gauge length of 200 mm))	-	2700.00	NIL
Clause 7.2 (iii)(Retention of breaking strength after UV exposure of 144 h)	-	10459.99	NIL
Clause 7.2 (iv)(Colour fastness to artificial light)	-	849.98	NIL
7.2-Table 1- v)(REQUIREMENTS - Bursting pressure, kgf/cm2)	-	1000.00	NIL

Complete

31 Dec, 2023

IS 17358 : Part 1 (2020)

Agro textiles “ Fencing nets for agriculture and horticulture purposes “ Specification Part 1 Fencing nets made from extruded polymer mesh

Agro Textiles-Fencing Nets for Agriculture and Horticul

19135.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4, table 1,2,3(MATERIALS)	-	2000.00	NIL
5,/ 5.1( MANUFACTURE (a)Hexagonal shape (see Fig. 1);(b) Diamond shape (see Fig. 2); and c) Square shape (see Fig. 3))	-	250.00	NIL
5.2(Colour)	-	300.00	NIL
6.0(TYPES ,(a)Light duty, b) Medium duty, and c) Heavy duty.)	-	299.99	NIL
(i)(Mass)	-	500.00	NIL
(ii)(Mesh Size, Traverse Direction)	-	250.00	NIL
(iii)(Mesh Size, Cross Direction)	-	250.00	NIL
(iv)(Thickness at joint)	-	249.98	NIL
(v)(Filament Thickness)	-	250.00	NIL
(vi)(Length)	-	500.00	NIL
(vi)(Width)	-	499.99	NIL
(vii) a(Tensile Strength before UV exposure, Machine Direction)	-	1099.99	NIL
(vii) b(Tensile Strength before UV exposure, Traverse Direction)	-	1100.00	NIL
(viii) a(Elongation before UV exposure, Machine Direction)	-	0.00	NIL
(viii) b(Elongation before UV exposure, Traverse Direction)	-	0.00	NIL
(ix) a(Tensile Strength after UV exposure, Machine Direction)	-	10180.00	NIL
(ix) b(Tensile Strength after UV exposure, Traverse Direction)	-	2199.98	NIL

Complete

31 Dec, 2023

IS 8008 (2022)

Injection Moulded/Machined Polyethylene Fittings for Water Supply ï¿½ Specification ( Second Revision )

Injection Moulded/Machined Polyethylene Fittings for Wa

10552.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	3044.00	NIL
4.2(Material)	-	2000.00	NIL
5(COLOUR)	-	250.00	NIL
6.1(The nominal outside diameter)	-	500.00	NIL
6.2(Bends, tees, pipe ends and end caps designation)	-	0.00	NIL
7(WELD LENGTH)	-	250.00	NIL
8(VISUAL APPEARANCE)	-	300.00	NIL
9.1(DIMENSIONS OF FITTINGS)	-	500.00	NIL
10.1.1(Length of Pipe for Welding Test)	-	249.99	NIL
10.1.2(Sandwich Flange Hydraulic Testing)	-	6700.00	NIL
10.2(Carbon Black Content and Dispersion)	-	700.00	NIL
10.3(Melt Flow Rate)	-	1100.00	NIL
10.4(Density)	-	500.00	NIL
10.5(Oxidation Induction Time)	-	2200.00	NIL
10.6(Overall Migration)	-	1325.00	NIL
11.1(Type Tests)	-	0.00	NIL
11.2(Acceptance Tests)	-	1900.00	NIL

Complete

31 Dec, 2023

IS 15532 (2004)

Plastics crates for fruits and vegetables - Specification

Plastics Crates for Fruits and Vegetables

14350.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3, 3.1(Requirements)	-	0.00	NIL
3.2(Material)	-	1999.98	NIL
3.3(Shape, Dimensions and Design)	-	500.00	NIL
3.4(Mass)	-	249.99	NIL
3.5(Appearance and Surface Finish)	-	300.00	NIL
3.6(Dimensional Stability)	-	699.98	NIL
3.7(Confluence Line Strength)	-	1100.00	NIL
3.8.1(Compressive Strength (Resistance to Applied Load))	-	1100.00	NIL
3.8.2(Resistance to Drop)	-	1099.98	NIL
3.9(Resistance to Environmental Stress Cracking)	-	1200.00	NIL
3.10.1(Suspension Test)	-	2200.00	NIL
3.10.2(Free-Fall Test)	-	0.00	NIL

Complete

31 Dec, 2023

IS 16513 (2016)

Agro textiles “ Insect nets for agriculture and horticulture purposes “ Specification

Agro Textiles - Insect Nets for Agriculture and Horticu

20873.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6/6.1( REQUIREMENTS Dimensions and Mass a) Length)	-	250.00	NIL
6/6.1( REQUIREMENTS Dimensions and Mass b) width)	-	249.99	NIL
6/6.1( REQUIREMENTS Dimensions and Mass c) Mass gm/m2)	-	250.00	NIL
4.2( Netting Fabric)	-	499.99	NIL
5.0(types a) Type I — having mesh of 30; b) Type II — having mesh of 40; andc) c) Type III — having mesh of 50)	-	500.00	NIL
4/4.1.1/60°C / 95°C( MATERIAL / HDPE Monofilament Yarn)	-	1999.98	NIL
4.3( Colour)	-	300.00	NIL
6.2(Table-1)	-	13159.98	NIL

Complete

31 Dec, 2023

IS 17374 (2020)

Geosynthetics – Reinforced HDPE membrane for effluents and chemical resistance lining – Specification

Geosynthetics — Reinforced HDPE Membrane for Effluents

153789.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 3.1(Reinforced HDPE Membrane)	-	2000.00	NIL
Clause No. 5.3, Table No. 1, (i)(Thickness (mm))	-	250.00	NIL
Clause No. 5.3, Table No. 1, (ii)(Mass (g/m2))	-	250.00	NIL
Clause No. 5.3, Table No. 1, (iii)(Dimensions (length and width))	-	250.00	NIL
Clause No. 3.1, Table No. 1, (iv)(Carbon black content, percent)	-	924.98	NIL
Clause No. 3.1, Table No. 1, (v)(Carbon black dispersion)	-	949.98	NIL
Clause No. 5.3, Table No. 1, (vi)(Breaking load on 20 cm × 10 cm strip before UV exposure, N)	-	3800.00	NIL
Clause No. 5.3, Table No. 1, (vii)(Strain at maximum load, percent)	-	1099.99	NIL
Clause No. 5.3, Table No. 1, (viii)(Retention of breaking load on 20 cm × 10 cm strip after UV exposure of 144 h)	-	10460.00	NIL
Clause No. 5.3, Table No. 1, (ix)(Impact failure load, at 1524 mm drop, Min gram force at 50 percent failure)	-	1100.00	NIL
Clause No. 5.3, Table No. 1, (x)(Tear resistance, N)	-	1099.98	NIL
Clause No. 5.3, Table No. 1, (xi)(Puncture resistance, N)	-	1100.00	NIL
Clause No. 5.3, Table No. 1, (xii)(Bursting strength (Ball burst), N/cm2)	-	1100.00	NIL
Clause No. 5.3, Table No. 1, (xiii)(Seam strength before UV exposure, N/mm)	-	1350.00	NIL
Clause No. 5.3, Table No. 1, (xv)(Hydrostatic resistance before UV exposure, kg/cm2)	-	1000.00	NIL
Clause No. 5.3, Table No. 1, (xvi)(Hydrostatic resistance after UV exposure of 144 h, kg/cm2)	-	1000.00	NIL
Clause No. 5.3, Table No. 1, (xvii)(Low temperature crack resistance at minus 30 °C ± 1°C)	-	1600.00	NIL
Clause No. 5.3, Table No. 1, (xviii)(Oxidative induction time (OIT), minutes, (a) Standard OIT or (b) High Pressure OIT)	-	4399.98	NIL
Clause No. 5.3, Table No. 1, (xix)(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days, percent, (a) Standard OIT or (b) High Pressure OIT)	-	58400.00	NIL
Clause No. 5.3, Table No. 1, (xx)(Stress crack resistance, h)	-	1199.98	NIL
Clause No. 5.3, Table No. 1, (xxi)(Abrasion resistance)	-	875.00	NIL
Clause No. 5.3, Table No. 1, (xxii)(Ash content, percent)	-	949.98	NIL
Clause No. 5.4, Table No. 2, (i)(Change in weight, percent)	-	38800.00	NIL
Clause No. 5.4, Table No. 2, (ii)(Change in volume, percent)	-	0.00	NIL
Clause No. 5.4, Table No. 2, (iii)(Visual observations)	-	299.98	NIL
Clause No. 5.4, Table No. 2, (iv)(Change in tensile strength, percent)	-	0.00	NIL
Clause No. 5.4, Table No. 2, (v)(Change in elongation, percent)	-	1100.00	NIL
Clause No. 5.4, Table No. 2, (vi)(Change in 2 percent secant modulus, percent)	-	1099.98	NIL
Clause No. 5.4, Table No. 2, (vii)(Change in seam strength, percent)	-	1100.00	NIL
3.1(MATERIAL AND MANUFACTURE - -HDPE membrane -UV stablised or carbon black stablised LDPE or LLDPE shall contain minimum 2.5 percent of carbon black)	-	1999.98	NIL
3.2(MATERIAL AND MANUFACTURE - A suitable multi-layer membrane with adequate number of layers shall be produced using a combination of HDPE fabric and layers of coating film)	-	299.98	NIL

Complete

31 Dec, 2023

IS 8069 (1989)

High density polyethylene (HDPE) woven sacks for packing pesticides – Specification (second revision)

High density polyethylene (HDPE) woven sacks for packin

6513.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Fabric)	-	2000.00	NIL
3.2(Sacks)	-	0.00	NIL
3.3(Liner)	-	1999.98	NIL
3.4(Lamination)	-	2000.00	NIL
3.5(Seam)	-	250.00	NIL
3.6(Mouth of sack)	-	249.99	NIL
3.7(Handles)	-	0.00	NIL
3.8(Capacity)	-	500.00	NIL
4.1, Table 1 (i) (a)(Breaking strength of fabric, (a) Widthwise)	-	1350.00	NIL
4.1, Table 1 (i) (b)(Breaking strength of fabric, (b) Lengthwise)	-	1099.98	NIL
4.1, Table 1 (ii) (a)(Seam breaking strength (a) Side seam)	-	1099.99	NIL
4.1, Table 1 (ii) (b)(Seam breaking strength (b) Bottom seam)	-	1100.00	NIL
4.2(Dimensions)	-	500.00	NIL
4.3(Mass)	-	249.99	NIL

Complete

31 Dec, 2023

IS 15827 (2019)

Cladding films for greenhouse / polyhouse - Specifications (First Revision)

Cladding Films for Greenhouse / Polyhouse — Specificati

267162.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Material Identification)	-	2000.00	NIL
6.1(Appearance & surface finish)	-	300.00	NIL
6.2(Durability ref clause No. 7.5)	-	0.00	NIL
Cl. no. 6.3 & Table 2(Tensile strength & elongation at break (TD & MD))	-	1350.00	NIL
6.3(Dart Drop test)	-	1100.00	NIL
6.3(Total Visible Light Transmittance)	-	750.00	NIL
6.3(Haze)	-	749.99	NIL
6.3(Tear Strength ( MD & TD))	-	1100.00	NIL
7.4(IR eefectiveness)	-	194000.00	NIL
7.2(width)	-	250.00	NIL
7.3(Elongation under Steady Load MD)	-	1099.99	NIL
7.5(Elongation after UV Exposure MD)	-	1100.00	NIL

Complete

31 Dec, 2023

IS 17216 (2019)

Polyethylene Mulch Films for Agriculture and Horticulture • Specification

Polyethylene Mulch Films for Agriculture and Horticultu

458000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Density)	-	500.00	NIL
5.1.2(Melt Flow Index)	-	1100.00	NIL
5.2.1(Visual Appearance)	-	300.00	NIL
5.2.2(Film Form)	-	0.00	NIL
5.2.4(Odour)	-	249.99	NIL
5.3.1.1(Tolerance on thickness)	-	249.99	NIL
5.3.1.2(Tolerance on width)	-	250.00	NIL
5.3.2(Impact Strength)	-	1349.98	NIL
5.3.2, Table 1(Nominal Film Thickness)	-	250.00	NIL
5.3.2, Table 1(Impact Failure Mass)	-	1349.98	NIL
5.3.3(Tensile Strength at Break)	-	2699.99	NIL
5.3.4(Elongation at Break)	-	0.00	NIL
5.3.5(Coefficient of Friction)	-	849.98	NIL
5.3.6(Elmendorf Tear Strength)	-	1999.98	NIL
5.3.7(Opacity)	-	575.00	NIL
5.4, Table 2(Carbon black, percent)	-	925.00	NIL
5.4, Table 2(Ash content, percent)	-	950.00	NIL
5.4, Table 2(Carbon black dispersion)	-	699.98	NIL
5.5(Service Life)	-	222580.00	NIL

Complete

31 Dec, 2023

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

Textiles - High Density Polyethylene (HDPE) Polypropyle

18580.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 Table 1(Dimensions)	-	250.00	NIL
5.2 Table 1(Ends per dm)	-	249.99	NIL
5.2 Table 1(Picks per dm)	-	250.00	NIL
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	249.99	NIL
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	15080.00	NIL
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	1099.99	NIL
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1100.00	NIL
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0.00	NIL
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0.00	NIL
5.2 Table 1(Drop impact strength)	-	1100.00	NIL
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	949.98	NIL
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	950.00	NIL

Complete

31 Dec, 2023

IS 17731 (2021)

Agro-Textiles Laminated Woven Orchard Protection Covers Specification

Agro-Textiles Laminated Woven Orchard Protection Covers

16000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 7, Table 1, (i)(Thickness, mm, Min)	-	500.00	NIL
Clause no. 7, Table 1, (ii)(Mass, g/m2, Min)	-	500.00	NIL
Clause No. 7, Table 1, (iii) a("Average breaking strength of laminated woven orchard protection cover fabric (Strip method, 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min, (a) Warpway")	-	1799.98	NIL
Clause No. 7, Table 1, (iii) b("Average breaking strength of laminated woven orchard protection cover fabric (Strip method, 325 mm × 50 mm test piece with gauge length of 200 mm), N, Min, (b) Weftway")	-	1300.00	NIL
Clause No. 7, Table 1, (iv)("Retention of breaking strength after UV exposure of 1000 h, percentage of original actual value (fabric), percent, Min")	-	0.00	NIL
Clause No. 7, Table 1, (iv)("Retention of breaking strength after UV exposure of 1000 h, percentage of original actual value (fabric), percent, Min")	-	0.00	NIL
Clause No. 7, Table 1, (v)(Strain at maximum load, percent)	-	1100.00	NIL
Clause No. 7, Table 1, (vi)("Impact failure load at 1524 mm drop, Min, gram force at 50 percent failure")	-	1099.98	NIL
Clause No. 7, Table 1, (vii)(Reinforcement band strength, N, Min)	-	1100.00	NIL
Clause No. 7, Table 1, (viii)(Ash content, percent, Max)	-	1199.98	NIL
Clause No. 7, Table 1, (ix)(Total visible light transmission, percent)	-	700.00	NIL
Clause No. 7, Table 1, (x)(Light diffusion, percent)	-	700.00	NIL
Clause No. 7, Table 1, (xi)(Thermicity IR effectiveness, percent)	-	1999.99	NIL
Clause No. 4.1(Width and linear density of HDPE Tapes)	-	499.99	NIL
Clause No. 4.1.1(Heat shrinkage of HDPE Tapes)	-	1100.00	NIL
Clause No. 6.1.1(Coating Lamination thickness, micron)	-	500.00	NIL
Clause No. 6.1.2(Sandwich lamination thickness , micron)	-	500.00	NIL
Clause No. 6.2(Joints/Seams)	-	500.00	NIL
Clause No. 6.3(Number and position of metal eyelets)	-	300.00	NIL
Clause No. 7.1(colour , texture and finish)	-	299.98	NIL

Complete

31 Dec, 2023

IS 11805 (2007)

Polyethylene pouches for packaging liquid milk - Specification - (Second Revision)

Polyethylene Pouches for Packaging Liquid Milk

4988.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5(Thickness)	-	250.00	NIL
5.6(Width)	-	250.00	NIL
5.7(Tensile Strength)	-	2199.98	NIL
8.1(Leak Test)	-	400.00	NIL
5.9(Dart Impact Resistance)	-	850.00	NIL
8.2(Drop Test)	-	1099.99	NIL
8.3(Ink adhesion test)	-	500.00	NIL
5.10(Slip (Coefficient of Friction))	-	850.00	NIL
5.4(Odour)	-	250.00	NIL
5.1(Visual)	-	300.00	NIL
5.2(Film form)	-	0.00	NIL

Complete

31 Dec, 2023

IS 17897 (2022)

Stone-Polymer Composite Flooring Tiles and Planks - Specification

Stone-Polymer Composite Flooring Tiles and Planks-Speci

14150.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Workmanship, Finish, Colour & Appearance)	-	300.00	NIL
6.2(Dimensions and Tolerances (Table-1))	-	750.00	NIL
6.2(Length)	-	250.00	NIL
6.2(Width)	-	249.98	NIL
6.2(Thickness (Mean))	-	250.00	NIL
6.2("Variation (Between any two measurements) ")	-	0	NIL
6.3(Physical & Mechanical Requirements (Table-2))	-	0	NIL
6.3(". Dimensional Stability (@80±2C for 6hrs. ")	-	700.00	NIL
6.3(Visual Inspection)	-	300.00	NIL
6.3(". Peel Strength (Speed:280±25mm/min.) ")	-	1350.00	NIL
6.3(Residual Indentation)	-	1149.98	NIL
6.3(Resistance to staining, cleanability score)	-	2000.00	NIL
6.3(Abrasion Resistance, percent by weight)	-	1350.00	NIL
6.3(Gap difference)	-	500.00	NIL
6.3(Average Value)	-	0.00	NIL
6.3(MaximumValue)	-	0.00	NIL
6.3(Locking strength of both sides)	-	2600.00	NIL
6.3(Flammability test)	-	1200.00	NIL
6.3(Colour fastness to Day light exposure, standard rating)	-	1499.98	NIL

Complete

31 Dec, 2023

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

40 mm to 200 mm

49544.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.6(Melt Flow Rate)	-	1100.00	NIL
4.2(Carbon black- b) Dispersion of carbon black)	-	700.00	NIL
Cl.7.1.5(Fusion Compatibility)	-	0.00	NIL
7.6(Melt now Rate (MFR))	-	2200.00	Male & Female coupler
7.5(Density)	-	1000.00	Male & Female coupler
Cl.7.1.6(Corrected Density)	-	0.0	NIL
Cl.7.1.7(MFR Test)	-	1100.00	NIL
Cl.7.2.l(Leakage Test)	-	850.00	NIL
Cl.7.2.2(Cl.7.2.2)	-	849.99	NIL
Cl.7.2.3(Weld ability Test)	-	4800.00	NIL
Cl.7.1.2(Hydraulic Characteristic)	-	1600.00	NIL
4.1(Quick Coupled Male and Female Couplers)	-	12100.00	Thermal Stability (2):4400 Volatile matter (2): 1400 Water content(2): 1400 Carbon Black content(2):1850 Carbon Black Disperssion(2): 1400 Wall thickness(2): 500.00 Workman ship &Appearance(Visual): 300 Holding attachement for coupler parts(2): 850
6.2, 6.2.1(Quick Coupled Fittings)	-	0.00	NIL
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	0.00	NIL
6.3.3(Material Identification - Insert Valve Coupler)	-	2000.00	NIL
6.3.4()	-	0.00	NIL
6.3.5(Material Identification - Saddle)	-	1050.00	NIL
6.3.6(Quick Coupled Pump Connectors - Visual)	-	300.00	NIL
Cl.7.1.l(Visual Anneara nce)	-	300.00	NIL
5(Dimensions of pipe - i) Outside diameter)	-	500.00	NIL
5(Dimensions of pipe - ii) Wall thickness minimum)	-	0.00	NIL
6(Visual Appearance)	-	0.00	NIL
7.1(Hydraulic Characteristics - Quality test)	-	0.00	NIL
7.1(Hydraulic Characteristics - Acceptance test)	-	0.00	NIL
7.2(Reversion Test)	-	700.00	NIL
7.3(Tensile Test- i) Tensile Strength)	-	1100.00	NIL
7.3(Tensile Test - ii)Elongation at Break)	-	0.00	NIL
7.4(Fusion Compatibility Test- a) Quality test)	-	0.00	NIL
7.4(Fusion Compatibility Test- b) Acceptance test)	-	0.00	NIL
7.5(Density)	-	900.00	NIL
4.2(Carbon black- a)carbon content)	-	900.00	NIL
Cl.6.2.6(Rubber Ring Hardness)	-	300.00	NIL
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	900.00	NIL

Complete

31 Dec, 2023

IS 8391 : Part 3 (2019)

Rubberized coir sheets for cushioning – Specification Part 3 Sandwiched (third revision)

Rubberized coir sheet for cushioning (sandwiched )

15450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4(Grades)	-	0.00	NIL
Clause 5("MANUFACTURE, WORKMANSHIP AND FINISH")	-	300.00	NIL
Clause 6("SHAPE AND DIMENSIONS")	-	500.00	NIL
Clause 7.1(Density)	-	700.00	NIL
Clause 7.2(Indentation Hardness)	-	1400.00	NIL
Clause 7.3(Resistance to Ageing)	-	2300.00	NIL
Clause 7.4(Resistance to Flexing)	-	4600.00	NIL
Clause 7.5(Compression Set (Aged))	-	1450.00	NIL
Clause 7.6(Compression Set (Un-aged))	-	1200.00	NIL
Clause 7.7(pH Value)	-	350.00	NIL
Clause 7.8(Chloride Content)	-	1000.00	NIL
Clause 7.9(Sulphate Content)	-	1000.00	NIL
"Clause 9.5 Table 2(i)"(Residual pesticides)	-	0.00	NIL
"Clause 9.5 Table 2(ii)"(pH of aqueous extract)	-	350.00	NIL
Clause 11(MARKING OR LABELLING)	-	300.00	NIL

Complete

31 Dec, 2023

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

2350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2.2, Table 1(Dimensions of 22 ½ deg Bends)	-	500.00	nil
3.2.2, Table 2(Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-	500.00	nil
3.2.3(Socket, measurements)	-	0	nil

Complete

31 Dec, 2023

IS 7328 (2020)

Specification for Polyethylene Material for Moulding and Extrusion ( Third Revision )

NIL

26850.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1.1(Density)	-	500.00	nil
5.2.1.2(MFI)	-	1100.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at yield)	-	1350.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at yield)	-	0	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at break)	-	0	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at break)	-	0	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec7)(Flexural modulas)	-	1350.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec6)(Dart Impact strength)	-	1000.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec4)(Izod/Charpy impact strength)	-	1350.00	nil
5.3.2 Table 6 IS 13360 (Part 5/Sec11)(Shore Aor D hardness)	-	375.00	nil
5.3.2 Table 6 IS 13360 (Part 11/Sec1)(Coeffiicient of friction)	-	850.00	nil
5.3.2 Table 6 IS 13360 (Part 6/Sec3)(Heat deflection temperature)	-	1100.00	nil
5.3.2 Table 6 IS 13360 (Part 6/Sec1)(Vicat softening temperature)	-	1100.00	nil
Annex B of IS 4984 5.3.2 Table6(Oxidation induction time)	-	2200.00	nil
5.5.6 IS 2530(Carbon black dispersion)	-	700.00	nil
5.4.3 10 ofIS 2530(Carbon black content)	-	925.00	nil
IS 13360(part8/Sec1)(Water absorption)	-	600.00	nil
5.4.35 15 ofIS 2530(Colour fastness to daylight)	-	850.00	nil
5.4.2 13 ofIS 2530(Colour fastness to water)	-	1750.00	nil
5.4.1 12 of IS 2530(Colour bleeding)	-	2000.00	nil
IS 13360(part 8/Sec9)(ESCR)	-	1200.00	nil
Annex C of IS4984(Volatile content)	-	700.00	nil
4 of IS 7016 (part 8)(Oven ageing)	-	700.00	nil
IS 13360(part 9/Sec8)(Transparency)	-	700.00	nil
IS15827(Natural/artificial weathering)	-	850.00	nil
IS 13360(part 9/Sec7)(Specular gloss)	-	700.00	nil
IS 13360(part 9/Sec5)(Haze or luminious transmittance)	-	700.00	nil
5.5.2(When the products are used in contact with foodstuffs, pharmaceuticals and drinking water, its requirements with respect to the material shall also be met as per 3.3, 3.4 and 3.5 of IS 10146.)	-	2200.00	nil

Complete

31 Dec, 2023

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

Type- A & Type-B

20244.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	300.00	nil
10.1(Surface Finish)	-	0.00	nil
7.2.1.1 Table3(Angle of taper (Note-1))	-	0.00	nil
10.7(Sulphated Ash Content)	-	1200.00	nil
5(CLASSIFICATION OF PIPES)	-	0.00	nil
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500.00	nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0.00	nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0.00	nil
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0.00	nil
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0.00	nil
7.2.1(DIMENSIONS-Socket)	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0.00	nil
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0.00	nil
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0.00	nil
8(SEALING RINGS)	-	0.00	nil
9.1(PIPE ENDS)	-	0.00	nil
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300.00	nil
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0.00	nil
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575.00	nil
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900.00	nil
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100.00	nil
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500.00	nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000.00	nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850.00	nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000.00	nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850.00	nil
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850.00	nil
11.2(Resistance to External Blows at 0°C)	-	1400.00	nil
10.3(Effect on Water Test)	-	3000.00	nil
6.1.2(PVC Resin)	-	4100.00	nil
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500.00	nil
7.1.4(Length)	-	0.00	nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0.00	NIL
13(Marking)	-	0.00	NIL

Complete

31 Dec, 2023

IS 8391 : Part 1 (2019)

Rubberized coir sheets for cushioning “ Specification Part 1 Curled (third revision)

Rubberized coir sheet for cushioning

14700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.7.1 (Density, Annex C)	-	500.00	nil
7.7.2(Indentation Hardness, Annex D)	-	1100.00	nil
7.7.3(Resistance to Ageing, Annex E)	-	2300.00	nil
7.7.4(Resistance to Flexing, Annex F)	-	3500.00	nil
7.7.5(Compression Set (Aged), Annex G)	-	1200.00	nil
7.7.6(Compression Set (Un-aged), Annex G)	-	900.00	nil
7.7.7(pH Value, Annex H)	-	350.00	nil
7.7.8(Chloride Content, Annex J)	-	1000.00	nil
7.7.9(Sulphate Content, Annex H-2)	-	1000.00	nil
B-1( DETERMINATION OF LENGTH AND WIDTH, Annex B)	-	250.00	nil
B-2.1(DETERMINATION OF THICKNESS, Annex B )	-	0	nil
B-2.2(Determination of Thickness of the Whole Sample, Annex B)	-	0	nil
6.1(Shape)	-	300.00	nil
6.2(Dimensions)	-	250.00	nil

Complete

31 Dec, 2023

IS 16352 (2020)

Geosynthetics – High density polyethylene (HDPE) geomembranes for lining – Specification (first revision)

High Density Polyethylene ( HDPE ) Geomembranes for Lin

93160.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	925.00	nil
5,3.1, Table 2,xi) Type I / II / III / IV / V / VI IS 2530(Carbon black content)	-	925.00	nil
5,3.1, Table2,iii) Type I / II / III / IV / V / VI Annex K(Lowest individual of 10 thickness value)	-	1800.00	nil
5,3.1, Table1,iii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Lowest individual of 10 thickness value)	-	500.00	Length, width & Indivisual Thickness
5,3.1, Table2,iv) Type I / II / III / IV / V / VI Annex L(Average asperity height)	-	500.00	nil
5,3.1, Table 2,v) d) Type I / II / III / IV / V / VI Annex B(Tensile properties: Breaking elongation)	-	2700.00	nil
5,3.1, Table1,xv) Type I / II / III / IV / V / VI / VII Annex J(Stress crack resistance)	-	0	nil
5,3.1, Table 2,xvi) Type I / II / III / IV / V / VI Annex J(Stress crack resistance)	-	13000.00	stress crack resistance 500hrs: 500.00, Conditioning Charge :12500.00
5,3.1, Table1,iv) d) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Breaking elongation)	-	0	nil
5,3.1, Table1,xii) Type I / II / III / IV / V / VI / VII ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	2200.00	nil
5,3.1, Table 2,xiii) Type I / II / III / IV / V / VI ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	2200.00	nil
5,3.1, Table1,xiii) Type I / II / III / IV / V / VI / VII Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	54000.00	nil
5,3.1, Table 2,xiv) Type I / II / III / IV / V / VI Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	2200.00	nil
3, 3.1(MATERIAL AND MANUFACTURE)	-	0	nil
3, 3.2(MATERIAL AND MANUFACTURE If two or more pieces of geomembranes are used, the material shall be joined together by a suitable heat sealing process keeping an overlap of at least 2.5 cm. )	-	0	nil
4, 4.1(VARIETY AND TYPES : Based on the finish, HDPE geomembrane shall be of following varieties)	-	0	nil
4.2,4.2.1(Based on the thickness of HDPE geomembrane, the material shall be classified as under)	-	0	nil
5,3.1, Table 1(Requirements of Smooth HDPE Geomembrane)	-	0	nil
5,3.1, Table1,i) a) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(Length)	-	500.00	nil
5,3.1, Table1,i) b) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(width)	-	0	nil
5,3.1, Table1,ii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Average thickness at a pressure of 2 ± 0.01 kPa)	-	0	nil
5,3.1, Table 2,v) a) Type I / II / III / IV / V / VI Annex B(Tensile properties: Yield strength,)	-	2700.00	nil
5,3.1, Table1,iv) b) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Breaking strength,)	-	0	nil
5,3.1, Table1,iv) c) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield elongation)	-	1600.00	nil
5,3.1, Table1,v) Type I / II / III / IV / V / VI / VII Annex C(Tear resistance)	-	1600.00	nil
5,3.1, Table1,vi) Type I / II / III / IV / V / VI / VII Annex D(Puncture resistanc)	-	1100.00	nil
5,3.1, Table1,vii) Type I / II / III / IV / V / VI / VII Annex E(Low temperature crack resistance at minus 30°C±1°C)	-	1800.00	nil
5,3.1, Table1,viii) Type I / II / III / IV / V / VI / VII Annex F(Hydrostatic resistance)	-	1600.00	nil
5,3.1, Table1,ix) Type I / II / III / IV / V / VI / VII Annex G(Seam strength : 85 percent of the original actual fabric strength or unbreakable seam)	-	1600.00	nil
5,3.1, Table1,xi) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black dispersion)	-	0	nil
5,3.1, Table1,xiv) Type I / II / III / IV / V / VI / VII Annex H(Retention of breaking strength after UV exposure of 144 h : 85 percent of the original actual fabric strength)	-	90350.00	conditioning charge-89000.00
5,3.1, Table 2(Requirements of Textured (Single or Double Sided) HDPE Geomembrane)	-	0	nil
6(DIMENSIONS AND TOLERANCES The dimensions of HDPE geomembrane when tested by the method given in IS 7016 (Part 1) shall be as agreed to between the buyer and the seller. However, the minimum width of the HDPE geomembrane shall be 5000 mm. A combination of panel width may be used to obtain desired width of geomembrane. Narrow width panels not less than 1000 mm in width may also be used but such pieces shall not exceed 1 piece per roll of finished material of specified width.)	-	500.00	nil
7, 7.1 Annex M(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS: )	-	0	nil
7, 7.2(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS)	-	500.00	nil

Complete

31 Dec, 2023

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

Containers for Packaging of Natural Mineral Water and P

17350.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0 (chem)(MATERIAL)	-	1050.00	nil
4.6.2(TRANSPARANCY)	-	700.00	nil
4.6.3(LEAKAGE TEST)	-	1000.00	nil
4.6.4(DROP TEST)	-	1100.00	nil
4.6.5(MIGRATION TEST)	-	1700.00	nil
4.6.6(PORTABILITY TEST)	-	2900.00	nil
4.6.4, clause 8 of IS:2798:1998(Drop test )	-	1100.00	NIL
4.2(Design, Shape & Dimension )	-	500.00	NIL
Cl. 4.4 (a)(Capacity)	-	500.00	NIL
4.5, IS:2798:1998(Wall thickness- Bottom, in mm)	-	500.00	nil
4.5, IS:2798:1998(Wall thickness- Middle , in mm)	-	0	nil
4.5, IS:2798:1998(Wall thickness- Top , in mm )	-	0	nil
4.4 , clause 5 of IS:2798:1998(Brimful capacity in ml)	-	300.00	nil
Cl.4.6.7.2 and 4.6.7.3, Table 3, (i)(Barium)	-	6000.00	nil
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ii)(Cobalt)	-	0	nil
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iii)(Copper)	-	0	nil
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iv)(Iron)	-	0	nil
Cl.4.6.7.2 and 4.6.7.3, Table 3, (v)(Lithium)	-	0	nil
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vi)(Manganese)	-	0	nil
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vii)(Zinc)	-	0	nil
CL 4.6.7.2 and 4.6.7.3, Table 3 (viii)(Antimony)	-	0	nil

Complete

31 Dec, 2023

IS 13489 (2000)

Textiles – Bed mattress – Specification (first revision)

Textile Bed mattress

19200.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 c)(Thickness)	-	250.00	NIL
5.1 b)(Width)	-	0	NIL
5.1 a)(Length)	-	0	NIL
3(TYPES)	-	0	NIL
4 Table 1(MATERIALS)	-	300.00	NIL
4 Table 1 i)a) IS 175(Case)	-	0	NIL
4 Table 1 i) b)(Case)	-	0	NIL
4 Table 1 ii) a) 1S8391(Cushioning)	-	0	NIL
4 Table 1 ii) b) IS 1741(Cushioning)	-	0	NIL
4 Table 1 ii) c) IS 7933(Cushioning)	-	0	NIL
4 Table 1 iii) a) IS 1920(Piping)	-	0	NIL
4 Table 1 iv) IS 1895(Tying tapes)	-	0	NIL
4 Table 1 v) IS 1720(Sewing thread)	-	0	NIL
5(DIMENSIONS)	-	250.00	NIL
5.1 Fig. l(Type 1 Mattress)	-	0	NIL
5.2(Type 2 Mattress)	-	0	NIL
5.2 a)(Length)	-	0	NIL
5.2 b)(Width)	-	0	NIL
5.2 c)(Thickness)	-	0	NIL
6(MANUFACTURE)	-	300.00	NIL
6.1(MANUFACTURE)	-	300.00	NIL
6.2(MANUFACTURE)	-	0	NIL
6.3(MANUFACTURE)	-	0	NIL
6.4(MANUFACTURE)	-	0	NIL
6.5(MANUFACTURE)	-	0	NIL
8(PACKING)	-	0	NIL
8.2(PACKING)	-	0	NIL

Complete

31 Dec, 2023

IS 14787 (2000)

Unplasticized pvc pipes (Ducts) and fittings for underground telecommunications cable installation - Specification

Unplasticized PVC Pipes (Ducts) and Fittings for Underg

18250.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Composition)	-	0.00	NIL
6(colour)	-	300.00	NIL
7.1(Diameter and wall thickness)	-	500.00	NIL
7.3(Insertion depth)	-	0.00	NIL
7.4(Length of pipe, L)	-	0.00	NIL
8.1(Visual appearance)	-	300.00	NIL
8.2(Pipe Stifness)	-	1100.00	NIL
8.3(Crush Resistance)	-	1100.00	NIL
8.4(Flattening)	-	500.00	NIL
8.5(Heat distortion)	-	1100.00	NIL
8.6(Co-efficient of Friction)	-	1100.00	NIL
8.7(Bending)	-	700.00	NIL
9.1(Impact strength)	-	1100.00	NIL
9.2(Tensile Strength and Elongation)	-	1600.00	NIL
9.3(Reversion)	-	700.00	NIL
9.4(Stress relief)	-	700.00	NIL
9.5(Vicat Softening Temperature)	-	1100.00	NIL
9.6(Density)	-	500.00	NIL
10(Resistance to chemical action)	-	1100.00	NIL
11(Ash content)	-	950.00	NIL
12(Titanium dioxide)	-	1200.00	NIL
13(Fittings)	-	250.00	NIL
14(Hydrostatic test for joint)	-	1250.00	NIL

Complete

31 Dec, 2023

IS 10889 (2004)

High density polyethylene films (First Revision)

13750.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Grades)	-	0	nil
5.1(Materials)	-	0	nil
5.2(Black Compound)	-	0	nil
6.1.1(Appearance)	-	300.00	nil
6.1.2(Film Form)	-	0	nil
6.1.3(Odour )	-	0	nil
6.1.4(Density)	-	500.00	nil
6.1.5(Melt Flow Rate)	-	1100.00	nil
6.1.6(Black Film)	-	1625.00	nil
6.2.1, Table 1(Nominal Thickness)	-	250.00	nil
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.2.2, Table 2(Nominal Width)	-	250.00	nil
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.3, Table 3(Yield Tolerance)	-	600.00	nil
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.4.1(Tensile Strength at Break)	-	2200.00	nil
6.4.1, Table 4(Direction)	-	0	nil
6.4.1, Table 4(Grade 1 and 2)	-	0	nil
6.4.2(Elongation at Break)	-	0	nil
6.4.2, Table 5(Elongation at Break, Percent Grade 1 and 2)	-	0	nil
6.4.3(Impact Resistance (Falling Dart))	-	850.00	nil
6.4.3, Table 6(Average Thickness of Film)	-	0	nil
6.4.3, Table 6(Impact Failure Load)	-	0	nil

Complete

31 Dec, 2023

IS 15609 (2005)

Polyethylene flexible pouches for the packing of natural mineral water and packaged drinking water - Specification

20000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.5 Annex J(Product resistance test for printed pouches)	-	500.00	nil
7.4 Annex H(Ink adhesion test for printed pouches)	-	500.00	nil
7.3 Annex G(Drop test )	-	1100.00	nil
7.2 Annex F(Stack Load test)	-	900.00	nil
7.1 Annex E(Water Potability test (after 30 Days) a) Taste b) Odour)	-	2900.00	nil
6.1.10 Annex -6 of IS:2508:2016(Dart impact Resistance)	-	850.00	nil
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - b. Crosswise direction)	-	1100.00	nil
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - a. Lengthwise direction)	-	0	nil
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength b. Crosswise direction)	-	1100.00	nil
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength a. Lengthwise direction)	-	0	nil
6.1.7 IS: 9845:1998(Migration- a. Amount of extractive )	-	1700.00	nil
6.1.6(Width)	-	250.00	nil
6.1.5 A-2 of IS: 2508:2016(Thickness)	-	250.00	nil
6.1.4(Odour)	-	500.00	nil
6.1.3(Winding of the Film )	-	0	nil
6.1.2(Film Form)	-	0	nil
6.1.1(Description)	-	0	nil
5(Material)	-	1050.00	nil
CL 6.1.11.2 and 6.1.11.3, Table 3 (i)(Barium)	-	6000.00	nil
Table 3(ii) Cobalt)	-	0	nil
Table 3(iii) Copper)	-	0	nil
Table 3(iv) Iron)	-	0	nil
Table 3(v) Lithium)	-	0	nil
Table 3(vi) Manganese)	-	0	nil
Table 3(vii) Zinc)	-	0	nil
Table 3(viii) Antimony)	-	0	nil

Complete

31 Dec, 2023

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	575.00	nil
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	500.00	nil

Complete

31 Dec, 2023

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

1744.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	500.00	nil
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	500.00	nil

Complete

31 Dec, 2023

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	500.00	nil

Complete

31 Dec, 2023

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

1819.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 2, table 2(Dimensions)	-	500.00	nil
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500.00	nil

Complete

31 Dec, 2023

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY(CIPET) : IPT-BHUBANESWAR

B/25, C.N.I complex, Patia, Bhubaneswar, BHUBANESWAR, Khordha, Odisha, 751024

7566177001 cipetbbsr@gmail.com

Scope List