BIS - LIMS (Laboratory Information Management System)

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY (CIPET) : IPT-BHUBANESWAR

B/25, C.N.I complex, Patia, Bhubaneswar, BHUBANESWAR, Khordha, Odisha, 751024

7566177001 cipetbbsr@gmail.com

Scope List

Reset

94 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

2350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2.2, Table 1(Dimensions of 22 ½ deg Bends)	-	500.00	nil
3.2.2, Table 2(Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-	500.00	nil
3.2.3(Socket, measurements)	-	0	nil

31 Dec, 2026

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

Type- A & Type-B

20244.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	300.00	nil
10.1(Surface Finish)	-	0.00	nil
7.2.1.1 Table3(Angle of taper (Note-1))	-	0.00	nil
10.7(Sulphated Ash Content)	-	1200.00	nil
5(CLASSIFICATION OF PIPES)	-	0.00	nil
7(DIMENSIONS-PIPE-Nominal Diameter)	-	500.00	nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0.00	nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0.00	nil
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0.00	nil
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0.00	nil
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0.00	nil
7.2.1(DIMENSIONS-Socket)	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0.00	nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0.00	nil
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0.00	nil
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0.00	nil
8(SEALING RINGS)	-	0.00	nil
9.1(PIPE ENDS)	-	0.00	nil
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300.00	nil
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0.00	nil
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575.00	nil
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900.00	nil
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100.00	nil
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500.00	nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000.00	nil
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850.00	nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000.00	nil
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850.00	nil
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850.00	nil
11.2(Resistance to External Blows at 0°C)	-	1400.00	nil
10.3(Effect on Water Test)	-	3000.00	nil
6.1.2(PVC Resin)	-	4100.00	nil
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500.00	nil
7.1.4(Length)	-	0.00	nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0.00	NIL
13.1(Marking)	-	0.00	NIL

31 Dec, 2026

-
-

IS 8391 : Part 1 (2019)

Rubberized coir sheets for cushioning “ Specification Part 1 Curled (third revision)

Rubberized coir sheet for cushioning

14700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.7.1 (Density, Annex C)	-	500.00	nil
7.7.2(Indentation Hardness, Annex D)	-	1100.00	nil
7.7.3(Resistance to Ageing, Annex E)	-	2300.00	nil
7.7.4(Resistance to Flexing, Annex F)	-	3500.00	nil
7.7.5(Compression Set (Aged), Annex G)	-	1200.00	nil
7.7.6(Compression Set (Un-aged), Annex G)	-	900.00	nil
7.7.7(pH Value, Annex H)	-	350.00	nil
7.7.8(Chloride Content, Annex J)	-	1000.00	nil
7.7.9(Sulphate Content, Annex H-2)	-	1000.00	nil
B-1( DETERMINATION OF LENGTH AND WIDTH, Annex B)	-	250.00	nil
B-2.1(DETERMINATION OF THICKNESS, Annex B )	-	0	nil
B-2.2(Determination of Thickness of the Whole Sample, Annex B)	-	0	nil
6.1(Shape)	-	300.00	nil
6.2(Dimensions)	-	250.00	nil

31 Dec, 2026

-
-

IS 16352 (2020)

Geosynthetics – High density polyethylene (HDPE) geomembranes for lining – Specification (first revision)

High Density Polyethylene ( HDPE ) Geomembranes for Lin

93160.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	925.00	nil
5,3.1, Table 2,xi) Type I / II / III / IV / V / VI IS 2530(Carbon black content)	-	925.00	nil
5,3.1, Table2,iii) Type I / II / III / IV / V / VI Annex K(Lowest individual of 10 thickness value)	-	1800.00	nil
5,3.1, Table1,iii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Lowest individual of 10 thickness value)	-	500.00	Length, width & Indivisual Thickness
5,3.1, Table2,iv) Type I / II / III / IV / V / VI Annex L(Average asperity height)	-	500.00	nil
5,3.1, Table 2,v) d) Type I / II / III / IV / V / VI Annex B(Tensile properties: Breaking elongation)	-	2700.00	nil
5,3.1, Table1,xv) Type I / II / III / IV / V / VI / VII Annex J(Stress crack resistance)	-	0	nil
5,3.1, Table 2,xvi) Type I / II / III / IV / V / VI Annex J(Stress crack resistance)	-	13000.00	stress crack resistance 500hrs: 500.00, Conditioning Charge :12500.00
5,3.1, Table1,iv) d) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Breaking elongation)	-	0	nil
5,3.1, Table1,xii) Type I / II / III / IV / V / VI / VII ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	2200.00	nil
5,3.1, Table 2,xiii) Type I / II / III / IV / V / VI ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	2200.00	nil
5,3.1, Table1,xiii) Type I / II / III / IV / V / VI / VII Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	54000.00	nil
5,3.1, Table 2,xiv) Type I / II / III / IV / V / VI Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	2200.00	nil
3, 3.1(MATERIAL AND MANUFACTURE)	-	0	nil
3, 3.2(MATERIAL AND MANUFACTURE If two or more pieces of geomembranes are used, the material shall be joined together by a suitable heat sealing process keeping an overlap of at least 2.5 cm. )	-	0	nil
4, 4.1(VARIETY AND TYPES : Based on the finish, HDPE geomembrane shall be of following varieties)	-	0	nil
4.2,4.2.1(Based on the thickness of HDPE geomembrane, the material shall be classified as under)	-	0	nil
5,3.1, Table 1(Requirements of Smooth HDPE Geomembrane)	-	0	nil
5,3.1, Table1,i) a) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(Length)	-	500.00	nil
5,3.1, Table1,i) b) Type I / II / III / IV / V / VI / VII IS 7016 (Part 1)(width)	-	0	nil
5,3.1, Table1,ii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Average thickness at a pressure of 2 ± 0.01 kPa)	-	0	nil
5,3.1, Table 2,v) a) Type I / II / III / IV / V / VI Annex B(Tensile properties: Yield strength,)	-	2700.00	nil
5,3.1, Table1,iv) b) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Breaking strength,)	-	0	nil
5,3.1, Table1,iv) c) Type I / II / III / IV / V / VI / VII Annex B(Tensile properties: Yield elongation)	-	1600.00	nil
5,3.1, Table1,v) Type I / II / III / IV / V / VI / VII Annex C(Tear resistance)	-	1600.00	nil
5,3.1, Table1,vi) Type I / II / III / IV / V / VI / VII Annex D(Puncture resistanc)	-	1100.00	nil
5,3.1, Table1,vii) Type I / II / III / IV / V / VI / VII Annex E(Low temperature crack resistance at minus 30°C±1°C)	-	1800.00	nil
5,3.1, Table1,viii) Type I / II / III / IV / V / VI / VII Annex F(Hydrostatic resistance)	-	1600.00	nil
5,3.1, Table1,ix) Type I / II / III / IV / V / VI / VII Annex G(Seam strength : 85 percent of the original actual fabric strength or unbreakable seam)	-	1600.00	nil
5,3.1, Table1,xi) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black dispersion)	-	0	nil
5,3.1, Table1,xiv) Type I / II / III / IV / V / VI / VII Annex H(Retention of breaking strength after UV exposure of 144 h : 85 percent of the original actual fabric strength)	-	90350.00	conditioning charge-89000.00
5,3.1, Table 2(Requirements of Textured (Single or Double Sided) HDPE Geomembrane)	-	0	nil
6(DIMENSIONS AND TOLERANCES The dimensions of HDPE geomembrane when tested by the method given in IS 7016 (Part 1) shall be as agreed to between the buyer and the seller. However, the minimum width of the HDPE geomembrane shall be 5000 mm. A combination of panel width may be used to obtain desired width of geomembrane. Narrow width panels not less than 1000 mm in width may also be used but such pieces shall not exceed 1 piece per roll of finished material of specified width.)	-	500.00	nil
7, 7.1 Annex M(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS: )	-	0	nil
7, 7.2(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS)	-	500.00	nil

31 Dec, 2026

-
-

IS 13489 (2000)

Textiles – Bed mattress – Specification (first revision)

Textile Bed mattress

19200.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 c)(Thickness)	-	250.00	NIL
5.1 b)(Width)	-	0	NIL
5.1 a)(Length)	-	0	NIL
3(TYPES)	-	0	NIL
4 Table 1(MATERIALS)	-	300.00	NIL
4 Table 1 i)a) IS 175(Case)	-	0	NIL
4 Table 1 i) b)(Case)	-	0	NIL
4 Table 1 ii) a) 1S8391(Cushioning)	-	0	NIL
4 Table 1 ii) b) IS 1741(Cushioning)	-	0	NIL
4 Table 1 ii) c) IS 7933(Cushioning)	-	0	NIL
4 Table 1 iii) a) IS 1920(Piping)	-	0	NIL
4 Table 1 iv) IS 1895(Tying tapes)	-	0	NIL
4 Table 1 v) IS 1720(Sewing thread)	-	0	NIL
5(DIMENSIONS)	-	250.00	NIL
5.1 Fig. l(Type 1 Mattress)	-	0	NIL
5.2(Type 2 Mattress)	-	0	NIL
5.2 a)(Length)	-	0	NIL
5.2 b)(Width)	-	0	NIL
5.2 c)(Thickness)	-	0	NIL
6(MANUFACTURE)	-	300.00	NIL
6.1(MANUFACTURE)	-	300.00	NIL
6.2(MANUFACTURE)	-	0	NIL
6.3(MANUFACTURE)	-	0	NIL
6.4(MANUFACTURE)	-	0	NIL
6.5(MANUFACTURE)	-	0	NIL
8(PACKING)	-	0	NIL
8.2(PACKING)	-	0	NIL

31 Dec, 2026

-
-

IS 14787 (2000)

Unplasticized pvc pipes (Ducts) and fittings for underground telecommunications cable installation - Specification

Unplasticized PVC Pipes (Ducts) and Fittings for Underg

18250.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Composition)	-	0.00	NIL
6(colour)	-	300.00	NIL
7.1(Diameter and wall thickness)	-	500.00	NIL
7.3(Insertion depth)	-	0.00	NIL
7.4(Length of pipe, L)	-	0.00	NIL
8.1(Visual appearance)	-	300.00	NIL
8.2(Pipe Stifness)	-	1100.00	NIL
8.3(Crush Resistance)	-	1100.00	NIL
8.4(Flattening)	-	500.00	NIL
8.5(Heat distortion)	-	1100.00	NIL
8.6(Co-efficient of Friction)	-	1100.00	NIL
8.7(Bending)	-	700.00	NIL
9.1(Impact strength)	-	1100.00	NIL
9.2(Tensile Strength and Elongation)	-	1600.00	NIL
9.3(Reversion)	-	700.00	NIL
9.4(Stress relief)	-	700.00	NIL
9.5(Vicat Softening Temperature)	-	1100.00	NIL
9.6(Density)	-	500.00	NIL
10(Resistance to chemical action)	-	1100.00	NIL
11(Ash content)	-	950.00	NIL
12(Titanium dioxide)	-	1200.00	NIL
13(Fittings)	-	250.00	NIL
14(Hydrostatic test for joint)	-	1250.00	NIL

31 Dec, 2026

-
-

IS 10889 (2004)

High density polyethylene films (First Revision)

13750.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Grades)	-	0	nil
5.1(Materials)	-	0	nil
5.2(Black Compound)	-	0	nil
6.1.1(Appearance)	-	300.00	nil
6.1.2(Film Form)	-	0	nil
6.1.3(Odour )	-	0	nil
6.1.4(Density)	-	500.00	nil
6.1.5(Melt Flow Rate)	-	1100.00	nil
6.1.6(Black Film)	-	1625.00	nil
6.2.1, Table 1(Nominal Thickness)	-	250.00	nil
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.2.2, Table 2(Nominal Width)	-	250.00	nil
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.3, Table 3(Yield Tolerance)	-	600.00	nil
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	0	nil
6.4.1(Tensile Strength at Break)	-	2200.00	nil
6.4.1, Table 4(Direction)	-	0	nil
6.4.1, Table 4(Grade 1 and 2)	-	0	nil
6.4.2(Elongation at Break)	-	0	nil
6.4.2, Table 5(Elongation at Break, Percent Grade 1 and 2)	-	0	nil
6.4.3(Impact Resistance (Falling Dart))	-	850.00	nil
6.4.3, Table 6(Average Thickness of Film)	-	0	nil
6.4.3, Table 6(Impact Failure Load)	-	0	nil

31 Dec, 2026

-
-

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	575.00	nil
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	500.00	nil

31 Dec, 2026

-
-

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

1744.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	500.00	nil
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	500.00	nil

31 Dec, 2026

-
-

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 1(Dimensions)	-	500.00	nil

31 Dec, 2026

-
-

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

1819.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 1(Manufacture)	-	0	nil
3.2.2, Fig 2, table 2(Dimensions)	-	500.00	nil
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500.00	nil

31 Dec, 2026

-
-

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

1744.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.3, 3.3.1, Fig 1(Manufacture)	-	0	nil
3.3.2, table 1, fig 1(Dimensions)	-	500.00	nil
3.3.3(socket measurement shall comply with IS 10124 (Part 1).)	-	0	nil
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	500.00	nil

31 Dec, 2026

-
-

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 2(Manufacture)	-	0	nil
3.2.2, Fig 2, table 2(Dimensions)	-	500.00	nil
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500.00	nil
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	0	nil
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	0	nil

31 Dec, 2026

-
-

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 2(Manufacture)	-	0	nil
3.2.2, Fig 1, table 1(Dimensions)	-	500.00	nil
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500.00	nil
Table 1 (Clauses 3.2.2, 3.2.3, and Fig. 1)(Dimensions of 60o Bends)	-	0	nil
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 60o Bend for Elastomeric Sealing Ring Joint)	-	0	nil

31 Dec, 2026

-
-

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2, 3.2.1, Fig 2(Manufacture)	-	0	nil
3.2.2, Fig 1, table 1(Dimensions)	-	500.00	nil
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500.00	nil
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 45o Bend)	-	0	nil
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 45° Bend for Elastomeric Sealing Ring Joint)	-	0	nil

31 Dec, 2026

-
-

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2.2, Table 1(Dimensions of 30 deg Bends)	-	500.00	nil
3.2.2, Table 2(Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-	0	nil

31 Dec, 2026

-
-

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

1444.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	nil
3.2.2, Table 2(Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-	500.00	nil
3.2.2, Table 1(Dimension of 11 1/4° bends)	-	0	nil
3.2.3(Socket, Measurement)	-	0	nil

31 Dec, 2026

-
-

IS 9755 (2021)

Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

Textiles - High Density Polyethylene (HDPE) / Polypropy

24080.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6(Bottom Seam-The number of stitches/dm shall be 14 ± 2.)	-	300.00	nil
3.4(Liner-The thickness(A-2 of IS 2508) shall be 40 μm ± 10 percent in case of HMHDPE/ HDPE.)	-	500.00	nil
3.5(Bottom Seam-The two rows of stitches shall be separated from each other by minimum 5 mm)	-	0	nil
3.6(Bottom Seam-the outer stitch shall be minimum 8 mm from the outer edge of the sacks.)	-	0	nil
3.4(Liner-The width of the loose liner shall be minimum 20 mm more than the width of the sack.)	-	250.00	nil
3.4.2(Liner-The bottom seal of the loose liner shall be at least 25 mm from the bottom edge.)	-	250.00	nil
3.6(Bottom Seam-tThe stitching shall be done with double fold over seam to a depth of minimum 25 mm, so that the stitches pass through a minimum of six layers of the fabric.)	-	0	nil
3.3(Sacks)	-	300.00	nil
3.4(Liner)	-	500.00	nil
3.4.2(Lamination)	-	1800.00	nil
3.7(Mouth of the Sack)	-	250.00	nil
3.8(Capacity- The sack shall have the nominal capacity of 50 kg.)	-	250.00	nil
4.3(Mass-(Annexure E))	-	250.00	nil
3.6(Bottom Seam-The number of stitches/dm shall be 14 ± 2.)	-	500.00	nil
4.1 , Table 1(REQUIREMENTS)	-	3800.00	nil
4.2(UV Resistance)	-	10460.00	nil
4.1(Raw Meterial)	-	1999.98	NIL
4.2("Fabric d) Unlaminated Fabric Mass")	-	250.00	NIL
4.2("Fabric b) Linear Density")	-	500.00	NIL
4.3(Sacks)	-	500.00	NIL
4.4.1(Loose Liner)	-	2000.00	NIL
4.4.2(Visual Observation)	-	300.00	NIL
4.4.3(Bottom Seam of Loose Liner)	-	250.00	NIL
4.5(Mass of The Lamination)	-	499.99	NIL
4.5(Laminated Fabric)	-	0.00	NIL
4.5(Lamination Over Hang of the fabric after trimming)	-	0.00	NIL
4.6.1(Distance between the Two Row of Stitches)	-	250.00	NIL
4.6.1(Distance of outer stitch from the edge of the bag)	-	250.00	NIL
4.6.1(Depth of the Stitch( Double fold))	-	250.00	NIL
4.6.1(No.of Stitches/dm)	-	250.00	NIL
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	1100.00	NIL
4.6.2(Breaking Load for UV Stabilized sack)	-	1100.00	NIL
4.7(Mouth of the Sack)	-	250.00	NIL
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension a) Inside Length Type 1 & Type 2 ")	-	250.00	NIL
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension b) Inside Width ")	-	250.00	NIL
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	250.00	NIL
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	500.00	NIL
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	500.00	NIL
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	500.00	NIL
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	1350.00	NIL
"Table 1 of Cl. No.5.4 Sl. No. vii"(Breaking Strength of Bottom Seam (Ravelled strip method))	-	1350.00	NIL
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0.00	NIL
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0.00	NIL
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	949.98	NIL
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	950.00	NIL
"Table 1 of Cl. No.5.6 Sl. No. x"(Drop Impact Strength)	-	1100.00	NIL
Cl. No.5.2(Visual Observation)	-	300.00	NIL

31 Dec, 2026

-
-

IS 7903 (2017)

Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision)

48013.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.4( Line/ Cord beading IS 7903)	-	250.00	nil
4.0(Types IS 7903)	-	500.00	nil
5.1.1(Lamination IS 7903)	-	1050.00	nil
5.1.2(Lamination IS 7903)	-	0	nil
5.2.1(Construction IS 7903)	-	250.00	nil
5.3(Joint/Seam, IS 7903)	-	400.00	nil
5.4(Fixing of Eyelets, IS 7903)	-	0	nil
6.1 Table 1,i)(No of HDPE fabric layers ,IS 7903)	-	250.00	nil
6.1 Table 1,ii)(No of lamination layers, IS 7903)	-	0	nil
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	250.00	nil
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	2700.00	nil
6.1 Table 1 vii)(Elongation at break of fabric,warp, IS 1969 Part 1)	-	0	nil
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	28900.00	nil
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	1100.00	nil
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	1100.00	nil
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	1100.00	nil
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	1100.00	nil
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	850.00	nil
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	950.00	nil
6.2(Length, IS 7903)	-	250.00	nil
6.2(Width, IS 7903)	-	250.00	nil
6.2(height, IS 7903)	-	250.00	nil
6.3(Water Proofness,IS 7941)	-	1000.00	nil
6.3(Water Proofness, IS 7940)	-	5200.00	nil
3.3(Eyelets (Dimesnions) i) Starting thickness of metal Aluminium min ii) Outside dia of flange‘A’ iii) Flange formed height ‘B’ iv) Pierced dia ‘C’ v) Overall length ‘D’ vi) Internal dia of Barrel when closed ‘E’ min vii) Thickness of compressed material between eyelet and washer F’ max viii) Outside diameter of barrel under the flange‘G’ )	-	250.00	nil
3.2(HDPE Fabric (Material Identification))	-	1050.00	nil
3.1(HDPE Tapes (Carbon Black Content))	-	925.00	nil
3.1(HDPE Tapes (Material Identification))	-	1050.00	nil
5.1.1(Coating Thickness)	-	250.00	nil
5.1.1(Carbon Black Content)	-	925.00	nil
5.1.1(Sandwich lamination thickness)	-	250.00	nil
5.1.1(Mass of Finished Tarpaulin)	-	500.00	nil
5.1.1(UV Exposure (144 hrs))	-	26700.00	nil
5.1.1(Agening)	-	4200.00	nil

31 Dec, 2026

-
-

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

27630.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	500.00	nil
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	500.00	nil
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	500.00	nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	500.00	nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	500.00	nil
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	nil
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	nil
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	nil
4.1(Raw Material )	-	1050.00	nil
4.2 (Fabric)	-	0	nil
4.2 (Linear Density, 900 denier)	-	500.00	nil
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	500.00	nil
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	nil
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	nil
4.3(Sacks)	-	500.00	nil
4.4(Seam )	-	2550.00	Visual :500.00, Dimension: 500.00, Material Identification :1050.00, Denier of stitching material :500.00
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	nil
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	nil
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	nil
4.4(to a depth of minimum 25 mm, so that so that)	-	0	nil
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	nil
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	nil
4.4(Seam)	-	0	nil
4.5(Lamination )	-	1550.00	Visual :500.00, Material Identification: 1050.00
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	500.00	nil
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	nil
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100.00	nil
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1100.00	nil
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100.00	nil
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	nil
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	nil
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100.00	nil
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	1200.00	nil
5/5.6 (UV Resistance, )	-	10180.00	nil
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	1100.00	nil
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	1100.00	nil

31 Dec, 2026

-
-

IS 12650 (2018)

Textiles – Jute bags for packing 50 kg foodgrains – Specification (third revision)

7400.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-4.2(Manufacture-The number of stitches per decimeter shall be 10 ±1.)	-	250.00	nil
4-4.3(Manufacture-Safety Stitch-The number of safety union stitches per decimetre shall be10 ± 1.)	-	0	nil
4-4.1(MANUFACTURE- The bags shall be made from single piece of twill weave jute sacking of uniform construction having nominal mass of 579 g/m2 as given below with warp running along the length of the bag:)	-	300.00	nil
4-4.1-a)(MANUFACTURE)	-	0	nil
4-4.4(Manufacture-Hemming at the Mouth )	-	0	nil
4-4.5(Manufacture- Freedom from Defects )	-	0	nil
5-5.1-Table 1-Sr. no. i)(SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 a) Out side Length , cm 94 (For both type A & Type B) Tolerance + 4 / -0 cm)	-	500.00	nil
5-5.1-Table 1-Sr. no. i)(SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 b) Outside width, cm 57 (For both type A & Type B) Tolerance + 4 / -0 cm)	-	500.00	nil
5-5.1-Table 1-Sr. no.i i)(SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Ends/dm Type A 46 + 2 /Type B 76 + 4 / -3)	-	0	nil
5-5.1-Table 1-Sr. no.iii)(SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Picks/dm Type A 50 (2 x 25) / Type B 28 + 2)	-	0	nil
5-5.1-Table 1-Sr. no.iv)(SPECIFIC REQUIREMENTS-Cl. 8.5.2 of IS 9113 Corrected Mass/bag, g ( See Note 2) For both Type A & Type B 665 + 8.0 / -6.0 percent)	-	500.00	nil
5-5.1-Table 1-Sr. No.v)(SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): a ) Warpway- 1570 (160) for both type A & Type B)	-	1100.00	nil
5-5.1-Table 1-Sr. No.v)(SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): b ) Weftway- 1420 (145) for both type A & Type B)	-	1100.00	nil
5-5.1-Table 1-Sr. No.vi)(SPECIFIC REQUIREMENTS-Cl. 8.7 of IS 9113 Average side seam strength (5 cm ×20 cm raveled strip), Min, N (kgf): 490 (50) for both type A & Type B)	-	1100.00	nil
5-5.1-Table 1-Sr. No.vii)(SPECIFIC REQUIREMENTS-Cl. 8.2 of IS 9113 Moisture regain, percent, Max (see Note 3) 22 for both type A & Type B)	-	1000.00	nil
5-5.1-Table 1-Sr. No.viii)(SPECIFIC REQUIREMENTS-Cl. 8.8 of IS 9113 Oil content on dry de-oiled material, Max 3 for both type A & Type B)	-	1000.00	nil

31 Dec, 2026

-
-

IS 11584 (1986)

Specification for high density polyethylene (Hdpe) crates for milk satchets

7838.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2(Material )	-	1050.00	nil
2.3(Shape and Dimensions)	-	500.00	nil
2.4(Mass )	-	300.00	nil
2.5(Appearance and Surface Finish)	-	300.00	nil
2.6(Colour Fastness)	-	300.00	nil
2.7(Resistance to Stress)	-	1000.00	nil
2.8(Resistance to Applied Load)	-	1000.00	nil
2.9(Strength)	-	1000.00	nil
2.1(Dimensional Stability)	-	900.00	nil

31 Dec, 2026

-
-

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

5625.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	500.00	nil
table 1 sl.no: 02(20 )	-	0	nil
table 1 sl.no: 03(25 )	-	0	nil
table 1 sl.no: 04(32 )	-	0	nil
table 1 sl.no: 05(40 )	-	0	nil
table 1 sl.no: 06(50 )	-	0	nil
table 1 sl.no: 07(63 )	-	0	nil
table 1 sl.no: 08(75 )	-	0	nil
table 1 sl.no: 09(90 )	-	0	nil
table 1 sl.no: 10(110 )	-	0	nil
table 1 sl.no: 11(125 )	-	0	nil
table 1 sl.no: 12(140 )	-	0	nil
table 1 sl.no: 13(160 )	-	0	nil
table 1 sl.no: 14( 180 )	-	0	nil
table 1 sl.no: 15(200 )	-	0	nil
table 1 sl.no: 16(225 )	-	0	nil
table 1 sl.no: 17(250.0)	-	0	nil
table 1 sl.no: 18(280.0)	-	0	nil
table 1 sl.no: 19(315.0)	-	0	nil
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	500.00	nil
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	0	nil
2.2.3( inside diameter of the socket)	-	0	nil
2.2.3(socket length)	-	0	nil
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	0.00	nil
2.2.2 table 1(Laying Length)	-	0.00	nil
6.4 PART-1(Short term hydraulic test)	-	850.00	nil
2.1(General)	-	300.00	nil
2.2(Manufacture)	-	0.00	nil

31 Dec, 2026

-
-

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

5625.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	500.00	nil
table 1 sl.no: 02(20 )	-	0	nil
table 1 sl.no: 03(25 )	-	0	nil
table 1 sl.no: 04(32 )	-	0	nil
table 1 sl.no: 05(40 )	-	0	nil
table 1 sl.no: 06(50 )	-	0	nil
table 1 sl.no: 07(63 )	-	0	nil
table 1 sl.no: 08(75 )	-	0	nil
table 1 sl.no: 09(90 )	-	0	nil
table 1 sl.no: 10(110 )	-	0	nil
table 1 sl.no: 11(125 )	-	0	nil
table 1 sl.no: 12(140 )	-	0	nil
table 1 sl.no: 13(160 )	-	0	nil
table 1 sl.no: 14( 180 )	-	0	nil
table 1 sl.no: 15(200 )	-	0	nil
table 1 sl.no: 16(225 )	-	0	nil
table 1 sl.no: 17(250.0)	-	0	nil
table 1 sl.no: 18(280.0)	-	0	nil
table 1 sl.no: 19(315.0)	-	0	nil
2.1(General)	-	500.00	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	0	nil
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	0	nil
2.2.3( inside diameter of the socket)	-	0	nil
2.2.3(Socket length)	-	0	nil
6.1.1(VCM Content Test)	-	3000.00	nil

31 Dec, 2026

-
-

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

7219.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	0	nil
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	500.00	nil
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	500.00	nil
2.2.3( inside diameter of the socket)	-	500.00	nil
2.2.3(Socket length)	-	0	nil
6.1.1(VCM Content Test)	-	3000.00	nil

31 Dec, 2026

-
-

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

4219.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	0	nil
2.2.2, Table 1(Socket Laying Length)	-	500.00	nil
2.2.3( inside diameter of the socket)	-	500.00	nil
2.2.3(Socket length)	-	0	nil
6.1.1(VCM Content Test)	-	3000.00	nil

31 Dec, 2026

-
-

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

5625.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	0	nil
table 1 sl.no: 02(20 )	-	0	nil
table 1 sl.no: 03(25 )	-	0	nil
table 1 sl.no: 04(32 )	-	0	nil
table 1 sl.no: 05(40 )	-	0	nil
table 1 sl.no: 06(50 )	-	0	nil
table 1 sl.no: 07(63 )	-	0	nil
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2, Table 1(Size)	-	500.00	nil
2.2.2, Table 1(Union Laying Length)	-	500	nil
2.2.3( inside diameter of the socket)	-	500	nil
2.2.3(Socket length)	-	500	nil

31 Dec, 2026

-
-

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

requirement for Cap

5625.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2(diameter of the socket of cap)	-	500.00	nil
2.1(General)	-	0	nil
2.2(Manufacture)	-	0	nil
2.2.2(diameter of the socket of cap)	-	500	nil
2.2.2 table 1(Laying length)	-	500	nil

31 Dec, 2026

-
-

IS 12232 : Part 2 (1995)

Irrigation equipment - Rotating sprinkler: Part 2 test method for uniformity of distribution (First Revision)

Irrigation equipment - Rotating sprinkler: Part 2 Test

21200.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2,4.2.1,4.2.2,4.2.3(Construction & Workmanship)	-	300.00	NIL
4.3(Threaded connection)	-	400.00	NIL
4.4(Performance Requirement)	-	0.00	NIL
4.4.1(Effective pressures)	-	400.00	NIL
4.4.2(Actuating Mechanism)	-	399.98	NIL
6(STRENGTH TEST)	-	0.00	NIL
6.1(Test of Construction and parts)	-	300.00	NIL
6.2(Test of resistance of threaded connection)	-	400.00	NIL
6.2.1(Threaded connection to riser)	-	0.00	NIL
6.2.2(Nozzle threads intended for threaded connection)	-	400.00	NIL
6.3(Test of Resistance to Hydrostatic Pressure at ambient Temperature)	-	849.99	NIL
6.4(Test of Resistance to Hydrostatic Pressure at high temperature)	-	1599.98	NIL
6.5(Test of Water Tightness)	-	400.00	NIL
6.5.1(Water tightness of sprinkler)	-	400.00	NIL
6.5.1(a) Flow rate > 250lt./hr.)	-	0.00	NIL
6.5.1(b) Flow rate < 250lt./hr.)	-	0.00	NIL
6.5.2(Water tightness of nozzle connection)	-	399.99	NIL
7(OPERATING TESTS)	-	0.00	NIL
7.1(Test of Uniformity of rotation speed)	-	399.99	NIL
7.2(a) Nominal flow rate up to 250l./h)	-	0.00	NIL
7.2(b) Nominal flow rate exceeding 250l./h)	-	0.00	NIL
7.3(Test of Distribution Characteristics)	-	1500.00	NIL
7.4(Test of Effective Diameter of Coverage)	-	400.00	NIL
7.6(Test of range of effective pressures)	-	400.00	NIL
8(DURABILITY TEST (AFTER OPERATION FOR 2000 HRS.) *)	-	6250.00	NIL
8.1(Test of Construction and parts)	-	400.00	NIL
8.2(Test of Resistance to hydrostatic pressure at ambient temperature)	-	850.00	NIL
8.3(a) Flow rate > 250lt./hr)	-	0.00	NIL
8.3(b) Flow rate < 250lt./hr.)	-	0.00	NIL
8.4(Flow rate test of the Sprinkler)	-	399.99	NIL
8.5(Test of uniformity of rotating speed)	-	400.00	NIL
8.6(Distribution Characteristics)	-	1500.00	NIL
8.6(a)All Sprinklers)	-	0.00	NIL
8.6(b)For Sprinkler with nominal flow rates greater than 250l/h)	-	0.00	NIL

31 Dec, 2026

-
-

IS 8521 : Part 1 (1977)

Specification for industrial safety face shields: Part 1 with plastics visor

Industrial safety faceshield

9200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3(General requirements & Specific requirements)	-	500		nil
Cl 4(Visual and Dimensional Examination & Physical Requirements (Impact Resistance, Penetration Resistance, Visible Transmittance, Flammability & Disinfection))	-	8700.00		nil

31 Dec, 2026

-
-

First
Prev
1
2
3
4
Next
Last

Bureau of Indian Standards

The National Standards Body of India

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY (CIPET) : IPT-BHUBANESWAR

B/25, C.N.I complex, Patia, Bhubaneswar, BHUBANESWAR, Khordha, Odisha, 751024

7566177001 cipetbbsr@gmail.com

Scope List