BIS - LIMS (Laboratory Information Management System)

Bharat Test House Pvt. Ltd. 1668 Sonipat

1668 (DIV-II), HSIIDC INDUSTRIAL ESTATE, RAI, DIST. SONEPAT, HARYANA, INDIA, Sonipat, Sonipat, Haryana, 131029

9310314585 bthdiv2@bharattesthouse.com

Scope List

Reset

229 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

151

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

Steel Tube

13800 View breakup
For BIS samples: 1.5 times of BIS testing charges,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2 AND AS PER IS 10748(CARBON)	-	600	5% discount for BIS
6.2 AND AS PER IS 10748(MANGANESE)	-	600	5% discount for BIS
6.2 AND AS PER IS 513(SILICON)	-	600	5% discount for BIS
6.2 AND AS PER IS 10748(SULPHUR)	-	600	5% discount for BIS
6.2 AND AS PER IS 10748(PHOSPHORUS)	-	600	5% discount for BIS
6.2 AND AS PER IS 10748(COPPER)	-	600	5% discount for BIS
6.2 AND AS PER IS 513(NITROGEN)	-	600	5% discount for BIS
Clause - 6.1.1, Table-1(ALUMINIUM)	-	600	5% discount for BIS
Cl 8(Outer Diameter, Thickness & Mass)	-	600	5% discount for BIS
Cl. 8, 9 Table 3,4 & 5(Thickness)	-	600	5% discount for BIS
10.1(Thared Joints(IS:554))	-	600	5% discount for BIS
11(Length & tolerance)	-	600	5% discount for BIS
13.0(Leak Proof Test)	-	600	5% discount for BIS
Cl. 14.1(Tensile Strength)	-	600	5% discount for BIS
Cl. 14.1.1(Elongation)	-	600	5% discount for BIS
Cl. 14.2(Bend Test (uto and including 50 mm NB))	-	600	5% discount for BIS
Cl. 14.3(Flattening test (Over 50 mm NB))	-	600	5% discount for BIS
Cl 15(Workmanship)	-	600	5% discount for BIS

-
The scope may be restricted for plain ended pipe only. The scope may be restricted upto 40 mm

152

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

Steel tubes for structural purposes

8200 View breakup
For BIS samples: 1.5 times of BIS testing charges,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5.1, Table-3( CARBON)	-	300	5% discount for BIS
Clause - 5.1, Table-3(MANGANESE)	-	300	5% discount for BIS
Clause - 5.1, Table-3(SILICON)	-	300	5% discount for BIS
Clause - 5.1, Table-3(SULPHUR)	-	300	5% discount for BIS
Clause - 5.1, Table-3(PHOSPHURS)	-	300	5% discount for BIS
5 AND AS PER IS 10748(COPPER)	-	300	5% discount for BIS
Clause - 5.1, Table-3( ALUMINIUM)	-	300	5% discount for BIS
Cl 6(Outer Diameter, Thickness & Mass)	-	300	5% discount for BIS
Cl 7(Workmanship)	-	100	5% discount for BIS
8 AND AS PER IS 4736(MASS OF ZINC COATING)	-	300	5% discount for BIS
8.0(Uniformity of galvanized coating - IS 4736)	-	300	5% discount for BIS
9(Straightness)	-	300	5% discount for BIS
10(Lengths)	-	100	5% discount for BIS
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	300	5% discount for BIS
Clause 11.2, Table -2(Yield Strength)	-	300	5% discount for BIS
Clause 11.2, Table -2(Elongation)	-	300	5% discount for BIS
Cl 11.3.1(Cold bend test (upto & including 50 mm NB))	-	300	5% discount for BIS
12(Marking)	-	100	5% discount for BIS
13.0(Oiling and Painting - Visual)	-	200	5% discount for BIS
Clause - 5.1, Table-3(NITROGEN)	-	300	5% discount for BIS

-
The scope may be restricted upto 40 mm

153

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

Canvas boots, rubber sole

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	100	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	100	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	100	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	100	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	150	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	150	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	150	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	150	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	150	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	150	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	250	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	250	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	200	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	300	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	300	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	100	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	100	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	200	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	200	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	300	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	300	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	300	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	200	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	200	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	100	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	100	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	100	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	200	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	100	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	100	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	300	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	200	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	300	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	200	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	100	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	200	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	100	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	100	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	100	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	100	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	100	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	100	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	100	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	100	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	100	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	0	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	0	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	0	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	0	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	0	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	0	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	0	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	0	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	0	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	0	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	0	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	0	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	0	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	0	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	0	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	0	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	0	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	0	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	0	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	0	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	0	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	0	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	0	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	0	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	0	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	0	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	0	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	0	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	0	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	0	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	0	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	0	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	0	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	0	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	0	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	0	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	0	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	0	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	0	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	0	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	0	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	0	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	0	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	0	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	0	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	0	-
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	0	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	0	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	0	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	0	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	0	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	0	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	0	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	0	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	0	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	0	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	0	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	0	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	0	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	0	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	0	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	0	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	0	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	0	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	0	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	0	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	0	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	0	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	0	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	0	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	0	-
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	0	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	0	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	0	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	0	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	0	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	0	-
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	0	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	0	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	0	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	0	-
4.1.3.2(Fastness to mechanical washing (mild))	-	0	-
4.1.3(Cotton tape NEWAR)	-	0	-
Table 2 (ii)(Breaking load on 50 cm test length. N, Min)	-	0	-
4.1.6.2(Laces- Fastness to daylight)	-	0	-
4.1.6.3(Laces- Fastness to mechanical washing (mild))	-	0	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	0	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	0	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	0	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	0	-

-
Included w.e.f 13.02.2025

154

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

Unplasticized PVC Pipes for Potable Water Supplies

15250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	300	5% discount for BIS
10.1(Surface Finish)	-	300	5% discount for BIS
7.2.1.1 Table3(Angle of taper (Note-1))	-	500	5% discount for BIS
10.7(Sulphated Ash Content)	-	950	5% discount for BIS
5(CLASSIFICATION OF PIPES)	-	300	5% discount for BIS
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	500	5% discount for BIS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	5% discount for BIS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	500	5% discount for BIS
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	500	5% discount for BIS
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	500	5% discount for BIS
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	500	5% discount for BIS
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	500	5% discount for BIS
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	500	5% discount for BIS
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	500	5% discount for BIS
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	500	5% discount for BIS
7.2.1(DIMENSIONS-Socket)	-	500	5% discount for BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	500	5% discount for BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	500	5% discount for BIS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	500	5% discount for BIS
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	500	5% discount for BIS
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	5% discount for BIS
8(SEALING RINGS)	-	300	5% discount for BIS
9.1(PIPE ENDS)	-	900	5% discount for BIS
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	5% discount for BIS
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	600	5% discount for BIS
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900	5% discount for BIS
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	5% discount for BIS
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	5% discount for BIS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	4500	5% discount for BIS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	4500	5% discount for BIS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	4500	5% discount for BIS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	4500	5% discount for BIS
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	4500	5% discount for BIS
11.2(Resistance to External Blows at 0°C)	-	1250	5% discount for BIS
10.3(Effect on Water Test)	-	2500	5% discount for BIS
6.1.2(PVC Resin)	-	350	5% discount for BIS
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	500	5% discount for BIS
7.1.4(Length)	-	500	5% discount for BIS
6.1.1(VCM Content)	-	350	5% discount for BIS
7.2.1.2b(Maximum inner diameter of groove)	-	500	5% discount for BIS
13.1(Marking)	-	300	5% discount for BIS

-
-

155

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

Polyethylene Pipes for Water Supply

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 5.1 table-1(MATERIALS)	-	250	5% discount for BIS
5.2(Polyethylene Resin)	-	600	5% discount for BIS
8.9 table-6(Elongation at Break)	-	500	5% discount for BIS
8.8(Tensile Strength for Butt-fusion)	-	750	5% discount for BIS
8.7(Density)	-	500	5% discount for BIS
8.5 (Oxidation Induction Time)	-	1500	5% discount for BIS
8.4( Melt Flow Rate)	-	750	5% discount for BIS
8.2(Longitudinal Reversion Test)	-	750	5% discount for BIS
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	3500	5% discount for BIS
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	3500	5% discount for BIS
7.4.1.2(Ovality)	-	250	5% discount for BIS
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	250	5% discount for BIS
7.2(Length)	-	250	5% discount for BIS
6.2.1(6.1.1 Identification Stripes)	-	250	5% discount for BIS
6.2(Colour)	-	250	5% discount for BIS
6.1.4(PIPE DESCRIPTION)	-	250	5% discount for BIS
6.1.3 (PIPE DESCRIPTION)	-	250	5% discount for BIS
6, 6.1.2(PIPE DESCRIPTION)	-	250	5% discount for BIS
6, 6.1.1(PIPE DESCRIPTION)	-	250	5% discount for BIS
6, 6.1(PIPE DESCRIPTION)	-	250	5% discount for BIS
8.6(Overall migration)	-	1500	5% discount for BIS
8.3(Carbon black)	-	750	5% discount for BIS
5.4(Anti oxydent)	-	250	5% discount for BIS
5.3(e)(Carbon Black Master Batch)	-	1500	5% discount for BIS
5.3(d)(Carbon Black Master Batch)	-	0	5% discount for BIS
5.3(c)(Carbon Black Master Batch)	-	0	5% discount for BIS
5.3(b)(Carbon Black Master Batch)	-	0	5% discount for BIS
5.3 (a)(Carbon Black Master Batch)	-	0	5% discount for BIS
7()	-	0	5% discount for BIS
7()	-	0	NIL
8.10(Slow Crack Growth Rate)	-	1500	5% discount for BIS
7.1(Visual Appearance)	-	250	5% discount for BIS
5.2(Density)	-	600	5% discount for BIS
5.2(MFI @ 1900C/5.0 Kg)	-	600	5% discount for BIS
5.2(Volatile matter Content)	-	600	5% discount for BIS
5.3(Toluene Extract)	-	1500	5% discount for BIS
Clause 7.1(Visual Apperance)	-	250	5% discount for BIS
Clause 7.3(Coiling)	-	250	5% discount for BIS
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	600	5% discount for BIS
Cl. 8.3(Carbon Black Content)	-	750	5% discount for BIS
Cl. 8.3(Carbon Black Dispersion)	-	750	5% discount for BIS
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	600	5% discount for BIS
8.7(Density-IS 7328:2020)	-	500	5% discount for BIS
8.7(Corrected Density- IS 7328:2020)	-	500	5% discount for BIS
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	500	5% discount for BIS
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	500	5% discount for BIS
Cl 8.3(Carbon Black Content)	-	750	5% discount for BIS
Cl 8.3(Carbon Black Dispersion)	-	750	5% discount for BIS

-
-

156

IS 9973 (1981)

Specification for visor for scooter helmets

Visor for Scooter Helmets

6900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Impact resistance)	-	350	5% discount for BIS samples
5.2(Penetration resistance)	-	350	5% discount for BIS samples
5.3(Flammability)	-	600	5% discount for BIS samples
5.4.1(Distortion)	-	200	5% discount for BIS samples
5.4.2(Spherical&Cylindral error)	-	900	5% discount for BIS samples
5.4.3(Prismatic Error)	-	900	5% discount for BIS samples
5.4.4(Diffuse transmittance)	-	1000	5% discount for BIS samples
5.4.5(Light transmission)	-	1000	5% discount for BIS samples
5.5(Field of Vision)	-	800	5% discount for BIS samples
7.0(Mass)	-	300	5% discount for BIS samples
3(Materials)	-	200	None
4(Design)	-	200	None

-
-

157

IS 4151 (2015)

Protective helmets for motorcycle riders - Specification

Protective helmets for motorcycle riders

14200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Shell)	-	100	5% discount for BIS samples
4.5(Metal Parts)	-	500	5% discount for BIS samples
6.1(General)	-	100	5% discount for BIS samples
6.2(Shell)	-	100	5% discount for BIS samples
6.3(Protactive Padding)	-	200	5% discount for BIS samples
6.4(Retention System)	-	300	5% discount for BIS samples
6.7(Peripheral Vision)	-	500	5% discount for BIS samples
6.8(Workmanship and Finish)	-	300	5% discount for BIS samples
7.2(Impact Absorption Test)	-	2000	5% discount for BIS samples
7.3(Rigidity Test)	-	550	5% discount for BIS samples
7.4(Projections and Surface Friction Test)	-	1750	5% discount for BIS samples
7.5(Dynamic Test of Retention System)	-	600	5% discount for BIS samples
7.7(Retention Test of Helmet)	-	750	5% discount for BIS samples
7.8(Micro-Slip Test of the Chin Strap)	-	750	5% discount for BIS samples
7.9(Test for Resistance to Abrasion of the Chin Strap )	-	1250	5% discount for BIS samples
7.10.1(Inadvertent Release by Pressure)	-	1750	5% discount for BIS samples
7.10.3(Durability of Quick Release Mechanism)	-	1750	5% discount for BIS samples
7.10.2(Ease of Release)	-	1750	5% discount for BIS samples
7.6(Audibility Test)	-	2000	5% discount for BIS samples
7.10.1(Tests for Helmets)	-	1750	5% discount for BIS samples
7.10.2(Tests for Helmets)	-	1750	5% discount for BIS samples
7.10.3(Tests for Helmets)	-	1750	5% discount for BIS samples
5(Size)	-	100	5% discount for BIS samples
4.1(Material)	-	100	5% discount for BIS samples

-
-

158

IS 13395 (2021)

Performance of Handles and Handle Assemblies Attached to Cookware - Specification ( First Revision )

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Construction)	-	300	5% discount for BIS
4.2(Materials)	-	300	5% discount for BIS
4.3(Selection and Size)	-	300	5% discount for BIS
4.4(Position of handle and knob with respect to cookware)	-	300	5% discount for BIS
4.5(Attachment to cookware)	-	300	5% discount for BIS
5.1(General)	-	300	5% discount for BIS
5.2(Bending strength)	-	800	5% discount for BIS
5.3(Torque strength)	-	800	5% discount for BIS
5.4(Impact strength)	-	800	5% discount for BIS
5.5(Fatigue resistance)	-	1000	5% discount for BIS
5.6(Leakage)	-	1000	5% discount for BIS
5.7(Thermal insulation)	-	1000	5% discount for BIS
5.8(Heat resistance)	-	1000	5% discount for BIS
5.9(Washing resistance)	-	1000	5% discount for BIS
5.10(Burning resistance)	-	1000	5% discount for BIS

-
-

159

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

Gas Stove

22000 View breakup
For BIS samples: 1.5 times of BIS testing charges

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.24(Annexure E)(on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-	500	5% discount for BIS
Cl.23(There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-	500	5% discount for BIS
4.1(Requirement)	-	200	5% discount for BIS
5(Materials)	-	3200	5% discount for BIS (Cl. 5.1,5.2,5.3,5.4,5.5,5.7 & 5.1.2,5.1.3)
6(Design for Maintenance)	-	500	5% discount for BIS
7(Rigidity and Stability)	-	500	5% discount for BIS
8(Workmanship and Finish)	-	3000	5% discount for BIS (Cl. 8.1 and (7.3.2,7.3.3,7.4.1,7.4.2 of IS:5116) & Cl. 8.2,8.3)
9(Gas Taps)	-	500	5% discount for BIS
10(Injector Jets)	-	500	5% discount for BIS
11(Burners)	-	800	5% discount for BIS
12(Burner Pan Supports)	-	900	5% discount for BIS
13.1(Gas Soundness)	-	900	5% discount for BIS
13.2(Gas Leak Detector)	-	900	5% discount for BIS
14(Gas Inlet Connections)	-	800	5% discount for BIS
15(Strength and Rigidity)	-	700	5% discount for BIS
16(General Conditions of Test)	-	700	5% discount for BIS
17.1.1(Gas Consumption)	-	700	5% discount for BIS
18(Ignition and Flame Travel)	-	900	5% discount for BIS
19(Flame Stability)	-	500	5% discount for BIS
20(Noise Control)	-	1200	5% discount for BIS
21(Flash Back)	-	1000	5% discount for BIS
22(Formation of Soot)	-	500	5% discount for BIS
25(Fire Hazard and Limiting Temperature)	-	500	5% discount for BIS
26(Thermal Efficiency)	-	1000	5% discount for BIS
29(Marking)	-	500	5% discount for BIS

-
-

160

IS 21 (1992)

Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

Wrought aluminium and aluminium alloys

9500 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2, Table 1of IS:21 (Designation 19000)(Silicon)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19000)(Iron)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19000)(Copper)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19000)(Zinc)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19000)(Manganese)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19000)(Magnesium)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19000)(Aluminium)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	4500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 64430)(Lead)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19000)(Lead)	-	1000	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(0.2 Percent Proof Stress)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	Nil
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Tensile Strength)	-	0	Nil
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Bend Test (Radius of Bend))	-	0	Nil
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	Nil
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	Nil
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(0.2 Percent Proof Stress)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(0.2 Percent Proof Stress)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(0.2 Percent Proof Stress)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(0.2 Percent Proof Stress)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 1of IS:21 (Designation 64430)(Aluminium)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 64430)(Chromium)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 64430)(Titanium and or other grain refining elements)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Aluminium)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Tensile Strength)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Lead)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-A)(Lead)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-A)(Chromium)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19500)(Copper)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19500)(Silicon)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19500)(Iron)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19500)(Manganese)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19500)(Zinc)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19500)(Lead)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19500)(Cu+Si+Fe+Mn+Zn)	-	5500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Chromium)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Zinc)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-A)(Zinc)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Manganese)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-A)(Manganese)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Tensile Strength)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Iron)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-A)(Iron)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Tensile Strength)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Silicon)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-A)(Silicon)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Magnesium)	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Tensile Strength)	-	400	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	500	5% discount for BIS
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Bend Test (Radius of Bend))	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 64430)(Magnesium)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-A)(Magnesium)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 31000)(Copper)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 31000)(Magnesium)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-B)(Copper)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 51000-A)(Copper)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19600)(Aluminium)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19600)(Cu+Si+Fe+Mn+Zn)	-	4500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19600)(Lead)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19600)(Zinc)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19600)(Manganese)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19600)(Iron)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19600)(Silicon)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 19600)(Copper)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 31000)(Silicon)	-	1000	5% discount for BIS
4.2, Table 1of IS:21 (Designation 31000)(Iron)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 31000)(Manganese)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 31000)(Zinc)	-	500	5% discount for BIS
4.2, Table 1of IS:21 (Designation 31000)(Aluminium)	-	0	Nil
4.2, Table 1of IS:21 (Designation 31000)(Lead)	-	0	Nil
4.2, Table 1of IS:21 (Designation 31000)(Chromium)	-	0	Nil
4.2, Table 1of IS:21 (Designation 31000)(Titanium and or other grain refining elements)	-	0	Nil

-
-

161

IS 740 (1977)

Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (Second Revision)

6600 View breakup
For BIS samples: 1.5 times of BIS testing charges,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1of IS:740 (Designation & Condition 65032, 'W')(Tensile Strength of Size upto and including 25 mm)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation & Condition 64430, 'W')(Tensile Strength of Size upto and including 25 mm)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation & Condition 55000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation & Condition 55000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation & Condition 53000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation & Condition 53000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation & Condition 24345, 'W')(Tensile Strength of Size upto and including 12 mm)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation & Condition 19000, '112')(Tensile Strength of Size upto and including 12 mm)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Aluminium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Either Cr or Mn shall present)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Chromium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Titanium and or other grain refining elements)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Zinc)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Manganese)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Iron)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Silicon)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Magnesium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 65032)(Copper)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Aluminium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Cr+Mn)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Chromium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Titanium and or other grain refining elements)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Zinc)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Manganese)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Iron)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Silicon)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Magnesium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 64430)(Copper)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Aluminium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Cr+Mn)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Chromium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Titanium and or other grain refining elements)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Zinc)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Manganese)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Iron)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Silicon)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Magnesium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 55000)(Copper)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Aluminium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Cr+Mn)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Chromium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Titanium and or other grain refining elements)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Manganese)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Iron)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Silicon)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Magnesium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 53000)(Copper)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Aluminium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Chromium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Titanium and or other grain refining elements)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Zinc)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Manganese)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Iron)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Silicon)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Magnesium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 24345)(Copper)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 19000)(Aluminium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 19000)(Zinc)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 19000)(Manganese)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 19000)(Iron)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 19000)(Silicon)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 19000)(Magnesium)	-	500	5% discount for BIS
4.1, Table 1of IS:740 (Designation 19000)(Copper)	-	500	5% discount for BIS
6(Freedom From Defects)	-	500	5% discount for BIS
7(Dmension And Tolerances)	-	500	5% discount for BIS
9.2(Head Forming Test)	-	500	5% discount for BIS
11(Marking)	-	100	5% discount for BIS

-
-

162

IS 15558 (2005)

Mini domestic water heater for use with LPG - Specification

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Construction)	-	200	5% discount for BIS
4.1.2(Construction)	-	200	5% discount for BIS
4.1.3(Construction)	-	200	5% discount for BIS
4.1.4(Construction)	-	200	5% discount for BIS
4.1.5(Construction)	-	200	5% discount for BIS
4.1.6(Construction)	-	200	5% discount for BIS
4.1.7(Construction)	-	200	5% discount for BIS
4.1.8(Construction)	-	200	5% discount for BIS
4.1.9(Construction)	-	200	5% discount for BIS
4.1.10(Construction)	-	200	5% discount for BIS
4.1.11(Construction)	-	200	5% discount for BIS
4.1.12(Construction)	-	200	5% discount for BIS
5.1(Materials)	-	500	5% discount for BIS
5.2(Materials)	-	500	5% discount for BIS
5.3(Materials)	-	500	5% discount for BIS
5.4(Materials)	-	500	5% discount for BIS
5.5(Materials)	-	500	5% discount for BIS
6.1(Connections)	-	200	5% discount for BIS
6.2(Connections)	-	200	5% discount for BIS
6.3(Connections)	-	200	5% discount for BIS
6.4(Connections)	-	200	5% discount for BIS
6.5(Connections)	-	200	5% discount for BIS
6.6(Gas Inlet Connections)	-	200	5% discount for BIS
6.6(Gas Inlet Connections)	-	200	5% discount for BIS
6.6(Gas Inlet Connections)	-	200	5% discount for BIS
7(Flame Visibility)	-	500	5% discount for BIS
8(Gas Taps)	-	500	5% discount for BIS
9(Flame Failure Device)	-	500	5% discount for BIS
10(Ignition Device)	-	500	5% discount for BIS
11(Protection Against Accidental Overheating)	-	800	5% discount for BIS
12(Water Rate Adjuster)	-	500	5% discount for BIS
14(Gas Soundness)	-	1500	5% discount for BIS
15(Water Soundness)	-	1000	5% discount for BIS
16(Thermal Efficiency)	-	800	5% discount for BIS
17(Combustion)	-	1000	5% discount for BIS
18(Gas Consumption)	-	200	5% discount for BIS
19.1(Ignition and flame travel)	-	800	5% discount for BIS
19.2(Ignition and flame travel)	-	800	5% discount for BIS
19.3(Ignition and flame travel)	-	800	5% discount for BIS
20(Flame Stability)	-	200	5% discount for BIS
21(Noise Control)	-	800	5% discount for BIS
22(Flash Back)	-	1000	5% discount for BIS
23(Resistance to Draught)	-	800	5% discount for BIS
24(Fire Hazard And Limiting Temperature)	-	1000	5% discount for BIS
25(Time For Temperature Rise)	-	500	5% discount for BIS
26(Hot Water Output Test)	-	500	5% discount for BIS
27(Marking)	-	200	5% discount for BIS

-
-

163

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

Type 1 & Type 2

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	200	5% discount for BIS
4.1(Raw Material)	-	2000	5% discount for BIS
4.2(Tapes – Width IS 6192 and IS 11197)	-	100	5% discount for BIS
4.2(Tapes – Linear Density )	-	1000	Nil
4.3.1(The two rows of stitches shall be separated from each other)	-	250	5% discount for BIS
4.3.1( The outer stitch)	-	100	5% discount for BIS
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	100	5% discount for BIS
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	100	5% discount for BIS
4.3.1(stitches/dm)	-	300	5% discount for BIS
4.3.2(Mouth)	-	100	5% discount for BIS
4.4(Liner IS 10146 or IS 10910.)	-	2000	5% discount for BIS
4.4(Mass of the loose liner )	-	300	5% discount for BIS
4.4(Width of the loose liner)	-	100	5% discount for BIS
4.4(Length of the line)	-	100	5% discount for BIS
4.4(Bottom seam of the loose liner)	-	100	5% discount for BIS
4.4.1(Liner)	-	100	5% discount for BIS
4.5 and Table 1 i(Capacity)	-	500	5% discount for BIS
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	5% discount for BIS
5.2 and Table 1 ii b(Dimensions Inside Width)	-	250	5% discount for BIS
5.2 and Table 1 iii(Ends per dm )	-	300	5% discount for BIS
5.2 and Table 1 iv(Picks per dm )	-	300	5% discount for BIS
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500	Mass of Unlaminated Sack
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	500	Mass of the sack with liner
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	2000	5% discount for BIS
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	0	Charges already taken in cl. 5.2 vi a.
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1500	5% discount for BIS
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	1500	5% discount for BIS
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0	Charges already taken in cl. 5.2 viii a.
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	5000	5% discount for BIS
5.2 and Table 1 x(Ash content )	-	1200	5% discount for BIS
4.2(Construction)	-	250	5% discount for BIS

-
-

164

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

14600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.2(Material)	-	200	5% discount for BIS
Clause 4.2.1(Lining)	-	200	5% discount for BIS
Clause 4.2.2 (a)(Reinforcement)	-	200	5% discount for BIS
Clause 4.2.2 (b)(Reinforcement)	-	200	5% discount for BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	1200	5% discount for BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b)(Tensile Strength- cover)	-	1200	5% discount for BIS
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test lining)	-	1500	5% discount for BIS
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1500	5% discount for BIS
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	500	5% discount for BIS
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	500	5% discount for BIS
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2000	5% discount for BIS
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.6(Grip Strength Test)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1000	5% discount for BIS
Clause 5.2.1(BIS Certification Marking )	-	500	5% discount for BIS
Clause 4.3 Sub Clause 4.3.1 Table 1(Bore Size)	-	600	5% discount for BIS
Clause 4.3 Sub Clause 4.3.2 (a)(Thickness of Lining and Cover)	-	600	5% discount for BIS
Clause 4.3 Sub Clause 4.3.2 (b)(Thickness of Lining and Cover)	-	600	5% discount for BIS
Clause 4.3 Sub Clause 4.3.3(Length)	-	600	5% discount for BIS
Clause 4.1(General)	-	500	5% discount for BIS
Clause 4.2.3(Cover)	-	200	5% discount for BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a)(Elongation at break- Lining)	-	1200	5% discount for BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b)(Elongation at break- Cover)	-	1200	5% discount for BIS
Clause 5.2 (a)(Marking Manufacturer’s name or trade-mark, if any )	-	500	5% discount for BIS
Clause 5.2 (b)(Marking Words LPG, Max W.P. 1.0 MPa; )	-	500	5% discount for BIS
Clause 5.2 (c)(Marking Nominal bore, 1000111)	-	500	5% discount for BIS
Clause 5.2 (d)(Marking Batch/Lot No. )	-	500	5% discount for BIS
Clause 5.2 (e)(Marking Month and year of manufacture )	-	500	5% discount for BIS
Clause 5.2 (f)(Marking IS 9573 (Part 2) )	-	500	5% discount for BIS
Clause 5.2 (f)(Marking ecommended to replace before (MONTH/YEAR) )	-	500	5% discount for BIS
9.1(PIPE ENDS)	-	0	None

-
-

165

IS 9573 : Part 1 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 1 industrial application (Fourth Revision)

14400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 (General)	-	500	5% discount for BIS
Clause 4.2(Material)	-	200	5% discount for BIS
Clause 4.4 Sub Clause 4.4.2 (b)(Accelerated Ageing Test lining)	-	1500	5% discount for BIS
Clause 4.4 Sub Clause 4.4.2 (a)(Accelerated Ageing Test cover)	-	1500	5% discount for BIS
Clause 4.2.1(Lining)	-	200	5% discount for BIS
Clause 4.2.2(Reinforcement)	-	200	5% discount for BIS
Clause 4.2.3(Cover)	-	200	5% discount for BIS
Clause 4.4 Sub Clause 4.4.3 (a)(Resistance of Lining to n-pentane)	-	500	5% discount for BIS
Clause 4.5 Sub clause 4.5.1(Adhesion)	-	500	5% discount for BIS
Clause 4.5 Sub clause 4.5.2(Low Temperature Flexibility)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.3(Flexibility of Hose)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.4(Ozone Resistance)	-	2000	5% discount for BIS
Clause 4.5 Sub clause 4.5.5 4.5.5.1(Proof pressure test)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.5 4.5.5.2(Bursting pressure)	-	1000	5% discount for BIS
Clause 4.5 Sub clause 4.5.6(Electrical Continuity Test)	-	800	5% discount for BIS
Clause 4.5 Sub clause 4.5.7(Burning Behaviour)	-	1000	5% discount for BIS
Clause 5.2.1(BIS Certification Marking )	-	200	5% discount for BIS
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a)(Tensile Strength- Lining)	-	1200	5% discount for BIS
Clause 4.3 Sub Clause 4.3.3(Length)	-	600	5% discount for BIS

-
-

166

IS 7466 (2023)

Rubber Gasket for Pressure Cooker ï¿½ Specification ( Second Revision )

Type 1 & 2

14220 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Workmanship and Finish )	-	100	5% discount for BIS
3.4-Table 1(i)(Requirements of Rubber Used for Gaskets-Hardness IRHD)	-	0	None
3.4-Table 1(ii)(Requirements of Rubber Used for Gaskets-Tensile strength,)	-	0	None
3.4-Table 1(iii)(Requirements of Rubber Used for Gaskets-Elongation at break)	-	0	None
3.4-Table 1(iv-a)(Requirements of Rubber Used for Gaskets-Hardness IRHD(After ageing 3 days in Aie-oven Change From Original Value))	-	0	None
3.4-Table 1(iv-b)(Requirements of Rubber Used for Gaskets-Tensile strength(After ageing 3 days in Aie-oven Change From Original Value))	-	0	None
3.4-Table 1(iv-c)(Requirements of Rubber Used for Gaskets-Elongation at break(After ageing 3 days in Aie-oven Change From Original Value))	-	0	None
3.4-Table 1(v-a)(Requirements of Rubber Used for Gaskets-Hardness IRHD(After ageing in an autoclave Change From Original Value))	-	0	None
3.4-Table 1(v-b)(Requirements of Rubber Used for Gaskets-Tensile strength(After ageing in an autoclave Change From Original Value))	-	0	None
3.4-Table 1(v-c)(Requirements of Rubber Used for Gaskets-Elongation at break(After ageing in an autoclave Change From Original Value))	-	0	None
3.4-Table 1(vi)(Compression set)	-	0	None
3.5-ANNEX C(PERFORMANCE TEST FOR PRESSURE COOKER )	-	500	None
Clause 4.3 Table 1(Zinc oxide)	-	0	None
Clause 3.4 Table 1(Heavy metal content)	-	0	None
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	0	None
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	0	None
3.4. and Table 1 v) d(Requirements of Rubber Used for Gaskets-Volume(After ageing in an autoclave Change From Original Value))	-	0	None
Cl. No. 4.2(Workmanship and Finish)	-	100	5% discount for BIS
Cl. No. 4.1(Material)	-	900	5% discount for BIS
Cl. No. 3(Types)	-	250	5% discount for BIS
Cl. No. 4.3(Dimensions)	-	300	5% discount for BIS
Cl. No. 4.4, table no. 1(i)(Hardness)	-	400	5% discount for BIS
Cl. No. 4.4, table no. 1(ii)(Tensile strength)	-	700	5% discount for BIS
Cl. No. 4.4, table no. 1(iii)(Elongation at break)	-	50	5% discount for BIS
Cl. No. 4.4, table no. 1(iv)("Hardness, Tensile strength, Elongation at break)	-	1200	5% discount for BIS
Cl. No. 4.4, table no. 1(v)("Hardness, Tensile strength, Elongation at break percent")	-	1200	5% discount for BIS
Cl. No. 4.4, table no. 1(vi)(Change in volume)	-	900	5% discount for BIS
Cl. No. 4.4, table no. 1(vii)(Compression set)	-	700	5% discount for BIS
Cl. No. 4.4, table no. 1(viii)(Discolouration)	-	400	5% discount for BIS
Cl. No. 4.4, table no. 1(ix)(Odour and taste)	-	400	5% discount for BIS
Cl. No. 4.4, table no. 1(x)(Volatile matter)	-	600	5% discount for BIS
Cl. No. 4.4, table no. 1(xi)("Total zinc oxide, percent by mass, ")	-	1200	5% discount for BIS
Cl. No. 4.4, table no. 1(xii)(N-Nitrosamines,)	-	1200	5% discount for BIS
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)" Extractables)	-	1200	5% discount for BIS
Cl. No. 4.4, table no. 1(xv)("Polycyclic aromatic hydrocarbons (PAH) Benzo(a)pyrene (BaP)")	-	2000	5% discount for BIS
Cl. No. 4.5, Table no. 2(i)(Antimony)	-	300	5% discount for BIS
Cl. No. 4.5, Table no. 2(iii)(Chromium)	-	300	5% discount for BIS
Cl. No. 4.5, Table no. 2(iv)(Mercury)	-	300	5% discount for BIS
Cl. No. 4.5, Table no. 2(v)(Cadmium)	-	300	5% discount for BIS
Cl. No. 4.5, Table no. 2(vi)(Lead)	-	300	5% discount for BIS
Cl. No. 4.5, Table no. 2(viii)(Selenium)	-	300	5% discount for BIS
Cl. No. 4.5, Table no. 2(vii)(Barium)	-	300	5% discount for BIS
Cl. No.4.6(Performance test)	-	0	None
Cl. No. 5(Packing and Marking)	-	50	None

-
-

167

IS 5382 (2018)

Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials (Second Revision)

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.1(Dimensional tolerances)	-	400	5% discount for BIS
4.2.2(Imperfections and defects)	-	500	5% discount for BIS
4.2.2(Surface imperfections)	-	500	5% discount for BIS
4.2.2(i)In zones involved in sealing function)	-	500	5% discount for BIS
4.2.2(ii) In zones not involved in sealing function)	-	500	5% discount for BIS
4.2.2(Internal Imperfections)	-	500	5% discount for BIS
4.2.3(Hardness, IRHD from buttons )	-	500	5% discount for BIS
4.2.4(Tensile strength, MPa)	-	800	5% discount for BIS
4.2.5(Compression set in air)	-	2500	5% discount for BIS
4.2.5.2(Compression set at 23 ºC for 72 h)	-	2500	5% discount for BIS
4.2.5.2(Compression set at 70 ºC for 24 h)	-	2500	5% discount for BIS
4.2.5.3(Low temp compression set at -10 ºC for 72 h)	-	2500	5% discount for BIS
4.2.6(Ageing 7 days at 70 ºC)	-	3000	5% discount for BIS
4.2.6(Hardness, IRHD from buttons Tensile strength, % Elongation at break , % )	-	3000	5% discount for BIS
4.2.7(Stress relaxation, max)	-	6000	5% discount for BIS
4.2.8(Volume change in water , max/min 7 days at 70 ºC )	-	600	5% discount for BIS
4.2.9(Ozone resistance)	-	2300	5% discount for BIS
4.2.10(Spliced joint)	-	500	5% discount for BIS
15.4 (b)(Cold impact)	-	0	Nil
4.3.1(Low temperature performance - 25 degree C)	-	2400	5% discount for BIS
4.3.2(Volume change in oil)	-	800	5% discount for BIS

-
For BIS samples: 1.5 times of BIS testing charges

168

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

14500 View breakup
For BIS samples: 1.5 times of BIS testing charges,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1(Construction - Pressure Regulating Device)	-	500	5% discount for BIS
6.2(Construction-Safety Relief Device)	-	500	5% discount for BIS
6.3(Construction-Temperature Responsive Pressure Relief Device)	-	500	5% discount for BIS
4.1(Capacity )	-	500	5% discount for BIS
5.1.1(Body, Lid, Containers and Grid)	-	4500	5% discount for BIS
6(CONSTRUCTION)	-	500	5% discount for BIS
6.1(Pressure Regulating Device)	-	500	5% discount for BIS
6.1.3(Pressure Regulating Device)	-	500	5% discount for BIS
6.1.4(Pressure Regulating Device)	-	500	5% discount for BIS
6.1.5(Pressure Regulating Device)	-	500	5% discount for BIS
6.2(Safety Relief Device)	-	500	5% discount for BIS
6.2.1(Safety Relief Device)	-	500	5% discount for BIS
6.2.2(Safety Relief Device)	-	500	5% discount for BIS
6.3.1(Temperature Responsive Pressure Relief Device)	-	500	5% discount for BIS
6.3.1(Temperature Responsive Pressure Relief Device)	-	500	5% discount for BIS
6.4.1(Handles and Knobs)	-	500	5% discount for BIS
6.4.1.1(Handles and Knobs)	-	500	5% discount for BIS
7.1(WORKMANSHIP AND FINISH)	-	500	5% discount for BIS
7.2(WORKMANSHIP AND FINISH)	-	500	5% discount for BIS
7.3(WORKMANSHIP AND FINISH)	-	500	5% discount for BIS
7.4(WORKMANSHIP AND FINISH)	-	500	5% discount for BIS
8.1(Air Pressure Test)	-	500	5% discount for BIS
8.2(Proof Pressure Test)	-	500	5% discount for BIS
8.3(Operating Test for Pressure Regulating Device)	-	800	5% discount for BIS
8.4(Test for Safety Pressure Relief Device)	-	1000	5% discount for BIS
8.5(Bursting Pressure Test)	-	500	5% discount for BIS
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	1000	5% discount for BIS
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	1000	5% discount for BIS
8.7(Test for Spring Loaded Mechanism)	-	1000	5% discount for BIS
8.8(Test for Spring Loaded Mechanism)	-	1000	5% discount for BIS
8.9(Test for Spring Loaded Mechanism)	-	1000	5% discount for BIS
8.8(Test for Spring Loaded Mechanism)	-	1000	5% discount for BIS
8.9(Test for Spring Loaded Mechanism)	-	1000	5% discount for BIS

-
-

169

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

Hot rolled medium and high tensile structural steel

14765 View breakup
For BIS samples: 1.5 times of BIS testing charges,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	600	5% discount for BIS
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
8(Niobium as Nb)	-	600	5% discount for BIS
8(Titanium as Ti)	-	600	5% discount for BIS
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	600	5% discount for BIS
Clause 8, Table 1, Note 6(Boron)	-	600	5% discount for BIS
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	600	5% discount for BIS
10(Tensile Strength-IS:1608(P1)-22)	-	600	5% discount for BIS
10(Yield Stress-IS:1608(P1)-22)	-	600	5% discount for BIS
10(Elongation on SoA 5.65mm GL)	-	600	5% discount for BIS
Clause 11.3(Bend Test)	-	600	5% discount for BIS
Clause 12(Impact Test)	-	600	5% discount for BIS
15(Dimensions AxB)	-	600	5% discount for BIS
Cl 18(Weight)	-	600	5% discount for BIS
14.1(Soundness test)	-	600	5% discount for BIS
14.2(Grain Size)	-	600	5% discount for BIS
14.2(Inclusion)	-	600	5% discount for BIS

-
Exclusions: Y groove crackability test (Cl.13), Other test (Cl.14). The scope may be restricted upto 10 mm.

170

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

High strength deformed steel bars and wires

16500 View breakup
For BIS samples: 1.5 times of BIS testing charges,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Carbon %)	-	700	5% discount for BIS
4.1(Manganese %)	-	700	5% discount for BIS
4.1(Phosphorus %)	-	700	5% discount for BIS
4.1(Sulphur %)	-	700	5% discount for BIS
4.1(Silicon %)	-	700	5% discount for BIS
4.1( Copper %)	-	700	5% discount for BIS
4.1(Cr)	-	700	5% discount for BIS
4.1(Mo)	-	700	5% discount for BIS
4.1(Ni)	-	700	5% discount for BIS
4.1( Nitrogen%)	-	700	5% discount for BIS
4.1(CE)	-	0	Nil
4.1(Sulphur and phosphorous)	-	1400	5% discount for BIS
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Carbon-IS 228)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur-IS 228)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Phosphorous- IS 228)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	1400	5% discount for BIS
Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	700	5% discount for BIS
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-	0	Nil
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-	0	Nil
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-	0	Nil
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	0	Nil
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-	0	Nil
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	0	Nil
Cl 5(Deformations and Surface Characteristics)	-	0	Nil
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	0	Nil
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	0	Nil
Cl 6.1(Length, Width & Thickness)	-	700	5% discount for BIS
Cl 7.2(Weight)	-	0	Nil
Cl 8.1(UTM)	-	0	Nil
Cl. 8.1 Table 3(Elongation, percentage)	-	0	5% discount for BIS
Cl. 8.1 Table 3(TS/YS ratio)	-	0	Nil
Cl. 8.1 Table 3(Tensile Strength (TS))	-	0	5% discount for BIS
Cl. 8.1 Table 3(Yield Stress (YS))	-	0	5% discount for BIS
Cl 9.3(Load In One Direction)	-	700	5% discount for BIS
Cl. 9.3, Table 4(Bend Test )	-	700	5% discount for BIS
Cl 9.4(Load In Other Direction From Bend)	-	700	5% discount for BIS
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	700	5% discount for BIS
4.2(Niobium (Nb))	-	700	5% discount for BIS
4.2(Boron (B))	-	700	5% discount for BIS
Cl.4.2 of IS 1786 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	700	5% discount for BIS
Cl. 6.1(Nominal Size)	-	700	5% discount for BIS
Cl 7.2(Weight)	-	700	5% discount for BIS
9.2(Tensile test,IS:1608(Pt1)-2018)	-	700	5% discount for BIS
Clause 9.4(Rebend Test)	-	700	5% discount for BIS

-
EXCLUSIONS: Pull out test. The scope may be restricted upto 12 mm.

171

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

Type 1,2,3,4,5

19850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	200	5% discount for BIS
4.1(Raw Material)	-	2000	Nil
4.2(Tapes – Width IS 6192 and IS 11197)	-	100	Tape width only
4.2(Tapes – Linear Density )	-	1000	5% discount for BIS
4.2(Construction)	-	250	5% discount for BIS
4.3(Sacks)	-	200	5% discount for BIS
4.3.1(Bottom Seam)	-	100	5% discount for BIS
4.3.1( The two rows of stitches shall be separated from each other)	-	250	5% discount for BIS
4.3.1( The outer stitch)	-	100	5% discount for BIS
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	100	5% discount for BIS
4.3.1(The number of stitches/dm)	-	300	5% discount for BIS
4.3.2(Mouth)	-	100	5% discount for BIS
4.4 and Table 1 i(Capacity)	-	500	5% discount for BIS
5.2 and Table 1 ii a(Dimensions Inside Length)	-	300	5% discount for BIS
5.2 and Table 1 ii b(Dimensions Inside Width)	-	300	5% discount for BIS
5.2 and Table 1 iii(Ends per dm )	-	300	5% discount for BIS
5.2 and Table 1 iv(Picks per dm )	-	300	5% discount for BIS
5.1 and Table 1 v(Mass of sack )	-	500	5% discount for BIS
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	2000	5% discount for BIS
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	0	charges already taken in 5.2 and Table 1 vi a( in BS length)
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1500	5% discount for BIS
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	1500	5% discount for BIS
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	charges already taken in 5.2 and Table 1 viii a(Elongation Lengthwise)
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	5000	5% discount for BIS
5.2 and Table 1 x(Ash content )	-	1200	5% discount for BIS

-
-

172

IS 444 (2017)

Rubber hoses, textile - Reinforced, for general - Purpose water applications - Specification (Fifth Revision)

Type 1, 2, 3,

7300 View breakup
For BIS samples: 1.5 times of BIS testing charges,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification - IS 444)	-	100	5% discount for BIS
5(Lining - IS 444)	-	100	5% discount for BIS
5(Reinforcement - IS 444)	-	100	5% discount for BIS
5(Cover - IS 444)	-	100	5% discount for BIS
5(Lining and Cover - IS 444)	-	100	5% discount for BIS
6.1- Table 1(Internal diameters - ISO 4671)	-	200	5% discount for BIS
6.2(Concentricity - ISO 4671)	-	200	5% discount for BIS
6.3(Length -IS 4671)	-	200	5% discount for BIS
6.4( thickness of the lining plus cover - ISO 4671)	-	200	5% discount for BIS
6.4(If the cover is fluted, the depth of the flutes - ISO 4671)	-	200	5% discount for BIS
7.1 - Table 2( tensile strength of Lining - ISO 37 )	-	600	5% discount for BIS
7.1 - Table 2( tensile strength of Cover - ISO 37 )	-	600	5% discount for BIS
7.1 - Table 2(elongation at break of Lining - ISO 37)	-	600	5% discount for BIS
7.1 - Table 2(elongation at break of Cover - ISO 37)	-	600	5% discount for BIS
7.1 - Table 2(Change in tensile strength of Lining from original value after ageing(max) - ISO 188 and ISO 37)	-	600	5% discount for BIS
7.1 - Table 2(Change in elongation at break of Lining from original value after ageing (max.) - ISO 188 and ISO 37)	-	600	5% discount for BIS
7.1 - Table 2(Change in elongation at break of Cover from original value after ageing (max.) - ISO 188 and ISO 37)	-	1200	5% discount for BIS
7.2 - Table 3(Proof pressure at 23 °C - ISO 1402)	-	700	5% discount for BIS
7.2 - Table 3(Change in length at proof pressure - ISO 1402)	-	200	5% discount for BIS
7.2 - Table 3(Minimum burst pressure - ISO 1402)	-	500	5% discount for BIS
7.2 - Table 3(Adhesion between components - ISO 8033)	-	400	5% discount for BIS
7.2 - Table 3(Ozone resistance - ISO 7326)	-	1500	5% discount for BIS
7.2 - Table 3(Flexibility at 23 °C - Method A of ISO 1746)	-	400	5% discount for BIS
7.2 - Table 3(Low-temperature flexibility - Method B of ISO 4672)	-	700	5% discount for BIS

-
-

173

IS 3735 (1996)

Canvas Shoes, Rubber Sole

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	100	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	100	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	100	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	100	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	100	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	100	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	100	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	100	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	100	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	100	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	100	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	100	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	100	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	100	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	100	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	100	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	100	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	100	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	100	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	100	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	100	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	100	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	100	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	100	-
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	100	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	100	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	100	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	100	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	100	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	100	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	100	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	100	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	100	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	100	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	100	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	100	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	100	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	100	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	100	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	100	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	100	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	100	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	100	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	100	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	100	-
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	100	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	100	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	100	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	100	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	100	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	100	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	100	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	100	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	100	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	100	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	100	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	100	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	100	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	100	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	100	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	100	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	100	-
4.8(Adhesion )	-	100	-
4.7(Consolidation test )	-	100	-
4.6(Mass )	-	100	-
4.5(Finish )	-	100	-
4.4(Contruction )	-	100	-
4.3(Leg Height )	-	100	-
4.2(Design )	-	100	-
4.1.6.2(Thickness of components )	-	100	-
4.1.6.2(Ageing)	-	100	-
4.1.6.2(Elongation at break after ageing )	-	100	-
4.1.6.2(Tensile after ageing )	-	100	-
4.1.6(Compression set )	-	100	-
4.1.6(Elongation at break )	-	100	-
4.1.6(Tensile strength)	-	100	-
4.1.6(Hardness (after accelerated ))	-	100	-
4.1.6(Flexing resistance test)	-	100	-
4.1.6(Hardness )	-	100	-
4.1.6(Relative density)	-	100	-
4.1.5(Sulpher dyes content )	-	100	-
4.1.5(Breaking Load )	-	100	-
4.1.5(Length )	-	100	-
4.1.4(Thickness)	-	100	-
4.1.4(Size )	-	100	-
4.1.3(Color fastness to perspiration)	-	100	-
4.1.3(Colorfastness to washing)	-	100	-
4.1.3(Colorfastness to light )	-	100	-
4.1.3(Single thread breaking load)	-	100	-
4.1.1.2(Colorfastness to washing)	-	100	-
4.1.1.1(Colorfastness to light )	-	100	-
4.1.1 (Drill) (End & Picks/dm)	-	100	-
4.1.1 (canvas )(End & Picks/dm)	-	100	-
4.1.1 (canvas )(Breaking Load )	-	100	-
5, 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking)	-	100	-
" CL. 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking ")	-	100	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	100	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	100	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	100	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	100	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	100	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	100	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	100	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	100	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	100	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	100	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	100	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	100	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	100	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	100	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	200	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	200	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	200	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	200	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	200	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	200	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	200	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	200	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	200	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	200	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	200	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	200	-
4.1.2(Colorfastness to light )	-	200	-
4.1.2(Colorfastness to washing)	-	200	-
4.1.2(Breaking Strength )	-	200	-
4.1.2(Width )	-	200	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	200	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	200	-
4.1.3(Construction )	-	200	-
4.1.1 (Drill) (Colorfastness to light )	-	200	-

-
Included w.e.f 27.11.2024

174

IS 1989 : Part 1 (1986)

Specification for leather safety boots and shoes: Part 1 for miners (Fourth Revision)

Leather Safety Boots and Shoes - Part 1 : For Miners

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 (a)(Marking)	-	200	-
4.1 (b)(Marking)	-	200	-
4.1 (c)(Marking)	-	200	-
4.1 (d)(Marking)	-	200	-
4.1 (e)(Marking)	-	200	-
7.1(Design)	-	200	-
10.1(Finish)	-	300	-
10.3(Finish)	-	300	-
10.4(Finish)	-	300	-
11.1(Mass Boots with Leather Sole and Heel)	-	600	-
11.2(Mass Boots with Rubber Sole and Heel)	-	600	-
12(Performance test)	-	700	-
13(Design)	-	300	-
16.1(Finish)	-	400	-
16.2(Finish)	-	400	-
16.3(Finish)	-	400	-
16.4(Finish)	-	400	-
17.1(Mass Shoes with Leather Sole and Heel)	-	300	-
17.2(Mass Shoes with Rubber Sole and Heel)	-	300	-
18(Performance test)	-	500	-
4.1 (a)(Marking)	-	0	Repeated Test
4.1 (b)(Marking)	-	0	Repeated Test
4.1 (c)(Marking)	-	0	Repeated Test
4.1 (d)(Marking)	-	0	Repeated Test
4.1 (e)(Marking)	-	0	Repeated Test
7.1(Design)	-	0	Repeated Test
10.1(Finish)	-	0	Repeated Test
10.3(Finish)	-	0	Repeated Test
10.4(Finish)	-	0	Repeated Test
11.1(Mass Boots with Leather Sole and Heel)	-	0	Repeated Test
11.2(Mass Boots with Rubber Sole and Heel)	-	0	Repeated Test
12(Performance test)	-	0	Repeated Test
13(Design)	-	0	Repeated Test
16.1(Finish)	-	0	Repeated Test
16.2(Finish)	-	0	Repeated Test
16.3(Finish)	-	0	Repeated Test
16.4(Finish)	-	0	Repeated Test
17.1(Mass Shoes with Leather Sole and Heel)	-	0	Repeated Test
17.2(Mass Shoes with Rubber Sole and Heel)	-	0	Repeated Test
18(Performance test)	-	0	Repeated Test
4.1 (a)(Marking)	-	0	Repeated Test
4.1 (b)(Marking)	-	0	Repeated Test
4.1 (c)(Marking)	-	0	Repeated Test
4.1 (d)(Marking)	-	0	Repeated Test
4.1 (e)(Marking)	-	0	Repeated Test
7.1(Design)	-	0	Repeated Test
10.1(Finish)	-	0	Repeated Test
10.3(Finish)	-	0	Repeated Test
10.4(Finish)	-	0	Repeated Test
11.1(Mass Boots with Leather Sole and Heel)	-	0	Repeated Test
11.2(Mass Boots with Rubber Sole and Heel)	-	0	Repeated Test
12(Performance test)	-	0	Repeated Test
13(Design)	-	0	Repeated Test
16.1(Finish)	-	0	Repeated Test
16.2(Finish)	-	0	Repeated Test
16.3(Finish)	-	0	Repeated Test
16.4(Finish)	-	0	Repeated Test
17.1(Mass Shoes with Leather Sole and Heel)	-	0	Repeated Test
17.2(Mass Shoes with Rubber Sole and Heel)	-	0	Repeated Test
18(Performance test)	-	0	Repeated Test
Cl-8.1, 14.1 (a)(Tensile strength,)	-	300	-
Cl-8.1, 4.1 (b)(Colour fastness test to dry rubbing,)	-	300	-
Cl-8.1, 14.1 (c)(Solvent extractable substances,)	-	400	-
Cl-8.1, 14.1 (d)(Chromium ( as Cr2O3 ) content)	-	500	-
Cl-8.2, 14.2 (b)(Stitch tear strength)	-	100	-
Cl-8.2, 14.2 (c)(Colour fastness test for finished leather ( applicable in case of combination tanned leather );)	-	300	-
Cl-8.3, 14.3 (a)(Water absorption of Bottom Material)	-	100	-
Cl-8.3, 14.3 (b)(Resistance to cracking of Bottom Material)	-	100	-
Cl-8.3, 14.3 (c)(Total ash of Bottom Material)	-	400	-
4.1 (a)(Marking)	-	0	Repeated Test
4.1 (b)(Marking)	-	0	Repeated Test
4.1 (c)(Marking)	-	0	Repeated Test
4.1 (d)(Marking)	-	0	Repeated Test
4.1 (e)(Marking)	-	0	Repeated Test
7.1(Design)	-	0	Repeated Test
10.1(Finish)	-	0	Repeated Test
10.3(Finish)	-	0	Repeated Test
10.4(Finish)	-	0	Repeated Test
11.1(Mass Boots with Leather Sole and Heel)	-	0	Repeated Test
11.2(Mass Boots with Rubber Sole and Heel)	-	0	Repeated Test
12(Performance test)	-	0	Repeated Test
13(Design)	-	0	Repeated Test
16.1(Finish)	-	0	Repeated Test
16.2(Finish)	-	0	Repeated Test
16.3(Finish)	-	0	Repeated Test
16.4(Finish)	-	0	Repeated Test
17.1(Mass Shoes with Leather Sole and Heel)	-	0	Repeated Test
17.2(Mass Shoes with Rubber Sole and Heel)	-	0	Repeated Test
18(Performance test)	-	0	Repeated Test
Cl-8.1, 14.1 (a)(Tensile strength,)	-	0	Repeated Test
Cl-8.1, 4.1 (b)(Colour fastness test to dry rubbing,)	-	0	Repeated Test
Cl-8.1, 14.1 (c)(Solvent extractable substances,)	-	0	Repeated Test
Cl-8.1, 14.1 (d)(Chromium ( as Cr2O3 ) content)	-	0	Repeated Test
Cl-8.2, 14.2 (b)(Stitch tear strength)	-	0	Repeated Test
Cl-8.2, 14.2 (c)(Colour fastness test for finished leather ( applicable in case of combination tanned leather );)	-	0	Repeated Test
Cl-8.3, 14.3 (a)(Water absorption of Bottom Material)	-	0	Repeated Test
Cl-8.3, 14.3 (b)(Resistance to cracking of Bottom Material)	-	0	Repeated Test
Cl-8.3, 14.3 (c)(Total ash of Bottom Material)	-	0	Repeated Test

-
Included .ew.e.f.20.06.2025

175

IS 13273 (1991)

Vitreous enamelled inner tanks for storage water heater - specification

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.3.2.1(1238)	-	5000	-
Cl. 5.3.2.1(1238)	-	0	-
Cl. 5.3.2.3(13273)	-	6000	-
Cl 5.3.2.2(13273)	-	6000	-
Cl. 5.3.3(13273)	-	500	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	0	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	0	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	0	-
Cl. 5.3.2.2(3972(P-2/Sec-1))	-	0	-
Cl. 5.3.2.5(13273)	-	3000	-
Cl. 5.4(13273)	-	2500	-
Cl. 5.5(13273)	-	5000	-

-
-

176

IS 14261 (1995)

Transmission devices - V - Belts endless narrowv - Belts for industrial use - Specification

V - Belts

35500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Material And Workmanship)	-	5000	-
Cl 5.1(Cross-Section Dimensions)	-	13000	-
Cl 5.2(Cross-Section Dimensions)	-	13000	-
Cl 6(DESIGNATION)	-	1000	-
Cl 7(Length Measurement And Tolerances)	-	7500	-
Cl 7.2.1(Determination of Pitch Length)	-	5000	-
Cl 7.2.2(Determination of Pitch Length)	-	3500	-
Cl 7.2.3(Determination of Pitch Length)	-	0	-
Cl 7.3(Matched Belts)	-	0	-
Cl 4(Material And Workmanship)	-	0	-
Cl 5.1(Cross-Section Dimensions)	-	0	-
Cl 5.2(Cross-Section Dimensions)	-	0	-
Cl 6(DESIGNATION)	-	0	-
Cl 7(Length Measurement And Tolerances)	-	0	-
Cl 7.2.1(Determination of Pitch Length)	-	0	-
Cl 7.2.2(Determination of Pitch Length)	-	0	-
Cl 7.2.3(Determination of Pitch Length)	-	0	-
Cl 7.3(Matched Belts)	-	0	-
Cl 4(Material And Workmanship)	-	0	-
Cl 5.1(Cross-Section Dimensions)	-	0	-
Cl 5.2(Cross-Section Dimensions)	-	0	-
Cl 6(DESIGNATION)	-	0	-
Cl 7(Length Measurement And Tolerances)	-	0	-
Cl 7.2.1(Determination of Pitch Length)	-	0	-
Cl 7.2.2(Determination of Pitch Length)	-	0	-
Cl 7.2.3(Determination of Pitch Length)	-	0	-
Cl 7.3(Matched Belts)	-	0	-
Cl 4(Material And Workmanship)	-	0	-
Cl 5.1(Cross-Section Dimensions)	-	0	-
Cl 5.2(Cross-Section Dimensions)	-	0	-
Cl 6(DESIGNATION)	-	0	-
Cl 7(Length Measurement And Tolerances)	-	0	-
Cl 7.2.1(Determination of Pitch Length)	-	0	-
Cl 7.2.2(Determination of Pitch Length)	-	0	-
Cl 7.2.3(Determination of Pitch Length)	-	0	-
Cl 7.3(Matched Belts)	-	0	-

-
-

177

IS 4171 (1983)

Specification for copper rods and bars for general engineering purposes (First Revision)

Copper rods and bars for general engineering purposes

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 Table 1(1. Copper, including silver, min)	-	1000	-
Clause 4.1 Table 1(2. Tin, max)	-	1000	-
Clause 4.1 Table 1(3. Lead, max)	-	1000	-
Clause 4.1 Table 1(5. Nickel, max)	-	1000	-
Clause 4.1 Table 1(6. Arsenic, max)	-	1000	-
Clause 4.1 Table 1(7. Antimony, max)	-	1000	-
Clause 4.1 Table 1(8. Bismuth, max)	-	2000	-
Clause 4.1 Table 1(9. Phosphorus)	-	2000	-
Clause 4.1 Table 1(10. Selenium and Tellurium, max)	-	2000	-
Clause 4.1 Table 1(11. Total impurities ( excluding silver, nickel and phosphorus ), max)	-	1000	-
5.2(Hydrogen Embrittlement test)	-	1000	-
5.1(Tensile Properties)	-	2000	-
7.1(Dimension and Tolerances)	-	1000	-
Clause 4.1 Table 1(1. Copper, including silver, min)	-	0	-
Clause 4.1 Table 1(2. Tin, max)	-	0	-
Clause 4.1 Table 1(3. Lead, max)	-	0	-
Clause 4.1 Table 1(5. Nickel, max)	-	0	-
Clause 4.1 Table 1(6. Arsenic, max)	-	0	-
Clause 4.1 Table 1(7. Antimony, max)	-	0	-
Clause 4.1 Table 1(8. Bismuth, max)	-	0	-
Clause 4.1 Table 1(9. Phosphorus)	-	0	-
Clause 4.1 Table 1(10. Selenium and Tellurium, max)	-	0	-
Clause 4.1 Table 1(11. Total impurities ( excluding silver, nickel and phosphorus ), max)	-	0	-
5.2(Hydrogen Embrittlement test)	-	0	-
5.1(Tensile Properties)	-	0	-
7.1(Dimension and Tolerances)	-	0	-
Clause 4.1 Table 1(1. Copper, including silver, min)	-	0	-
Clause 4.1 Table 1(2. Tin, max)	-	0	-
Clause 4.1 Table 1(3. Lead, max)	-	0	-
Clause 4.1 Table 1(5. Nickel, max)	-	0	-
Clause 4.1 Table 1(6. Arsenic, max)	-	0	-
Clause 4.1 Table 1(7. Antimony, max)	-	0	-
Clause 4.1 Table 1(8. Bismuth, max)	-	0	-
Clause 4.1 Table 1(9. Phosphorus)	-	0	-
Clause 4.1 Table 1(10. Selenium and Tellurium, max)	-	0	-
Clause 4.1 Table 1(11. Total impurities ( excluding silver, nickel and phosphorus ), max)	-	0	-
5.2(Hydrogen Embrittlement test)	-	0	-
5.1(Tensile Properties)	-	0	-
7.1(Dimension and Tolerances)	-	0	-

-
-

178

IS 1897 (2008)

Copper strip for electrical purposes - Specification (Third Revision)

20300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(SUPPLY OF MATERIAL)	-	2000	-
CLAUSE 6(CHEMICAL COMPOSITION)	-	2000	-
CLAUSE 8(MECHANICAL PROPERTIES)	-	2000	-
CLAUSE 8.2(Bend Test)	-	2000	-
CLAUSE 9(ELECTRICAL RESISTIVITY TEST)	-	0	-
CLAUSE 10(TEST FOR CONTROLLED PROOF RESISTANCE (OPTIONAL))	-	1000	-
CLAUSE 11(DlMENSIONS AND TOLERANCES)	-	1300	-
CLAUSE 13(RETEST)	-	1000	-
Cl. 8.3(Edgewise bending,)	-	1000	-
Cl. 8.3(Thickness)	-	1000	-
Cl. 8.3(Tensile)	-	2000	-
Cl. 8.3(Elongation)	-	2000	-
Cl. 8.3(Hardness)	-	1000	-
CLAUSE 4(SUPPLY OF MATERIAL)	-	0	-
CLAUSE 6(CHEMICAL COMPOSITION)	-	0	-
CLAUSE 8(MECHANICAL PROPERTIES)	-	0	-
CLAUSE 8.2(Bend Test)	-	0	-
CLAUSE 10(TEST FOR CONTROLLED PROOF RESISTANCE (OPTIONAL))	-	0	-
CLAUSE 11(DlMENSIONS AND TOLERANCES)	-	0	-
CLAUSE 13(RETEST)	-	0	-
Cl. 8.3(Edgewise bending,)	-	0	-
Cl. 8.3(Thickness)	-	0	-
Cl. 8.3(Tensile)	-	0	-
Cl. 8.3(Elongation)	-	0	-
Cl. 8.3(Hardness)	-	0	-

-
-

179

IS 1545 (1994)

Solid drawn coppbr and copper alloy tubes for condensers and heat exchangers - Specification (Third Revision)

Heat Exchangers

20200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.5(GRADES)	-	1000	-
Cl. No.6(CONDITION)	-	1000	-
Cl. No.7(FREEDOM FROM DEFECTS)	-	1000	-
Cl. No.8.1(Dimensions)	-	1000	-
Cl. No.8.2(Tolerances)	-	1000	-
Cl. No.9.1, Table no.1(i)(Chemical composition-Copper)	-	1000	-
Cl. No.9.1, Table no.1(ii)(Lead)	-	1000	-
Cl. No.9.1, Table no.1(iii)(Tin)	-	1000	-
Cl. No.9.1, Table no.1(iv)(Iron)	-	1000	-
Cl. No.9.1, Table no.1(v)(Aluminium)	-	1000	-
Cl. No.9.1, Table no.1(vi)(Mangenese)	-	1000	-
Cl. No.9.1, Table no.1(vi)(Arsenic)	-	1000	-
Cl. No.9.1, Table no.1(vii)(Nickle)	-	1000	-
Cl. No.9.1, Table no.1(iv)(Zinc)	-	1000	-
Cl. No.9.1, Table no.1(iv)(Phosphorus)	-	500	-
Cl. No.9.1, Table no.1(iv)(T.L)	-	500	-
Cl. No.10.1.1(Hardness test)	-	500	-
Cl. No.10.1.2(Tensile Test)	-	500	-
Cl. No.10.2, Table no.2(Flattening Test)	-	500	-
Cl. No.10.3(Drift Expanding Test)	-	500	-
Cl. No.10.4.1(Eddy-Current Test)	-	0	-
Cl. No.10.4.2(Hydrostatic Test)	-	500	-
Cl. No.10.4.3(Pneumatic Test ( Alternative to Hydrostatic Test)	-	500	-
Cl. No.10.5(Microscopic Examination)	-	500	-
Cl. No.10.6.1(Ammonia Vapour Cracking Test)	-	500	-
Cl. No.10.6.2(Mercurous Nitrate Test)	-	500	-
Cl. No.13(Marking)	-	200	-
Cl. No.5(GRADES)	-	0	-
Cl. No.6(CONDITION)	-	0	-
Cl. No.7(FREEDOM FROM DEFECTS)	-	0	-
Cl. No.8.1(Dimensions)	-	0	-
Cl. No.8.2(Tolerances)	-	0	-
Cl. No.9.1, Table no.1(i)(Chemical composition-Copper)	-	0	-
Cl. No.9.1, Table no.1(ii)(Lead)	-	0	-
Cl. No.9.1, Table no.1(iii)(Tin)	-	0	-
Cl. No.9.1, Table no.1(iv)(Iron)	-	0	-
Cl. No.9.1, Table no.1(v)(Aluminium)	-	0	-
Cl. No.9.1, Table no.1(vi)(Mangenese)	-	0	-
Cl. No.9.1, Table no.1(vi)(Arsenic)	-	0	-
Cl. No.9.1, Table no.1(vii)(Nickle)	-	0	-
Cl. No.9.1, Table no.1(iv)(Zinc)	-	0	-
Cl. No.9.1, Table no.1(iv)(Phosphorus)	-	0	-
Cl. No.9.1, Table no.1(iv)(T.L)	-	0	-
Cl. No.10.1.1(Hardness test)	-	0	-
Cl. No.10.1.2(Tensile Test)	-	0	-
Cl. No.10.2, Table no.2(Flattening Test)	-	0	-
Cl. No.10.3(Drift Expanding Test)	-	0	-
Cl. No.10.4.2(Hydrostatic Test)	-	0	-
Cl. No.10.4.3(Pneumatic Test ( Alternative to Hydrostatic Test)	-	0	-
Cl. No.10.5(Microscopic Examination)	-	0	-
Cl. No.10.6.1(Ammonia Vapour Cracking Test)	-	0	-
Cl. No.10.6.2(Mercurous Nitrate Test)	-	0	-
Cl. No.13(Marking)	-	0	-

-
Included w.e.f 27.11.2024 Exclusion Cl 10.4.1 Eddy Current test

180

IS 14810 (2000)

Copper tubes for plumbing - Specification

23700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4("General Requirements")	-	2500	-
Clause 5(Supply of material)	-	2500	-
Clause 6("Freedom from defects")	-	2500	-
Clause 7(Chemical composition)	-	2200	-
Clause 10("DIMENSIONS AND TOLERANCES")	-	2000	-
Clause 11.1(Tensile Test)	-	2000	-
Clause 11.2(Drift Expanding Test)	-	2000	-
Clause 12(HYDROSTATIC TEST)	-	2000	-
Clause 13(Sampling and criteria for conformity)	-	2000	-
Clause 14(Marking)	-	2000	-
1()	-	2000	-

-
-

First
Prev
5
6
7
8
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Bharat Test House Pvt. Ltd. 1668 Sonipat

1668 (DIV-II), HSIIDC INDUSTRIAL ESTATE, RAI, DIST. SONEPAT, HARYANA, INDIA, Sonipat, Sonipat, Haryana, 131029

9310314585 bthdiv2@bharattesthouse.com

Scope List