BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

990 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 16014 (2024)

MECHANICALLY WOVEN DOUBLE-TWISTED HEXAGONAL WIRE MESH GABIONS REVET MATTRESSES ROCK FALL NETTING AND OTHER PRODUCTS FOR CIVIL ENGINEERING PURPOSES GALVANIZED STEEL WIRE OR GALVANIZED STEEL WIRE WITH POLYMER COATING SPECIFICATION ( Second Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5 (Material and Manufacture)	-
Cl-5.1.1 (Class 1 double-twisted mesh)	-
Cl-5.1.2 (Class 2 double-twisted mesh)	-
Cl-5.4.1 (Galvanized Rings)	-
Cl-5.4.2 (Stainless Steel Fasteners)	-
Cl-6.1 (Tensile Strength)	-
Cl-6.2, Table-7 (i) (Mesh wire dia, mm)	-
Cl-6.2, Table-7 (ii) (Tensile Strength Parallel to twist, kN/m)	-
Cl-5.3 (Lacing wire and stiffeners)	-
Cl-7.1.1 (Mass of Zinc/Zinc Alloy Coating)	-
Cl-7.1.3 (Ageing and Corrosion Resistance)	-
Cl-7.2 (a) (Specific gravity)	-
Cl-7.2 (b) (Tensile strength)	-
Cl-7.2 (c) (Hardness)	-
Cl-7.2 (e) (Salt spray exposure)	-
Cl-7.2 (f) (Modulus of Elasticity)	-
Cl-8.12 (Mesh Opening Tolerances)	-
Cl-9 (Workmanship)	-
Cl-12.1 (Tensile Strength of Wire Mesh Panel)	-
Cl-12.4 (Metallic Coating Mass)	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (i) (Mesh wire dia, mm)	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (ii) (Edge/Selvedge wire dia, mm)	-
Cl-5.5, 8.1, 8.2, 8.9, Table-1,2, 3, 4, 5, (iii) (Lacing wire dia, mm)	-

-
-

IS 2556 : Part 3 (2024)

Vitreous China Sanitary Appliances - Specification Part 3 Specific Requirements of Squatting Pans (sixth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-3 (GENERAL REQUIREMENTS)	-
Cl-5 (CONSTRUCTION)	-
Cl-6.1, Table-1 (i) (Length)	-
Cl-6.1, Table-1 (ii) (Length of opening, &fin)	-
Cl-6.1, Table-1 (iii) (Height)	-
Cl-6.1, Table-1 (iv) (Width of opening, small end)	-
Cl-6.1, Table-1 (v) (Width of opening, wide end)	-
Cl-6.1, Table-1 (vi) (Slope of bottom of pan)	-
Cl-6.1, Table-1 (vii) ("Distance between the centre of outlet to the inside face of flushing rim at the back, Mm")	-
Cl-6.1, Table-1 (viii) (Width)	-
Cl-6.1, Table-1 (ix) (Length of footrest)	-
Cl-6.2, (Connecting Dimensions)	-
Cl-7 (FINLSH)	-
Cl-8.3 (Water Holding Capacity Test)	-
Cl-8.4 (Saw Dust Test)	-
Cl-10 (Marking)	-

-
-

IS 11169 : Part 1 (2022)

Specification for steels for cold heading cold extrusion applications: Part 1 wrought carbon and low alloy steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
17 (Shape, Dimensions and tolerances)	-
8.1 (Tensile Test)	-
8.1 (Hardness Test)	-
Cl.4.3,7.2 & Table-A.2 (Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Aluminium- Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl. 7 (Carbon)	-
Cl. 7 (Sulphur)	-
Cl. 7 (Phosphorous)	-
Cl. 7 (Manganese)	-
Cl. 7 (Silicon)	-
Cl. 7 (Nickel)	-
Cl. 7 (Chromium)	-
Cl. 7 (Aluminium)	-
Cl. 7 (Molybdenum)	-
Cl. 7 (Boron)	-
Cl. 7 (Copper)	-
Cl. 7 (Cr+Ni+Mo)	-
Cl. 7 (Sn)	-
Cl. 7 (V)	-
Cl. 7 (Cr+Ni+Cu+Sn+Mo+V)	-
Cl-14 (SURFACE QUALITY)	-
Cl-17.2.2 (Length)	-
CL 7.2 (Diameter ( average 8))	-

-
-

IS 14490 (2024)

Plain Copier Paper â Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.3 (Grammage (Substance))	-
5.4 (Thickness)	-
5.5 (Size)	-
5.6, Table 1, i (ISO brightness, percent, Min)	-
5.6, Table 1, ii (Opacity, percent, Min)	-
5.6, Table 1, iii (One minute cobb test, both sides, g/m2 , Max)	-
5.6, Table 1, iv (Surface strength, Dennison (Wax Pick))	-
5.6, Table 1, v (Smoothness for both sides (Bendsten), ml/min, Max)	-
5.6, Table 1, vi (Ash content (at 900 °C), percent by mass, Max)	-
5.6, Table 1, vii (Taber stiffness, Min: Machine direction, Cross direction)	-
5.6, Table 1, viii (Tear Index, mN.m2 /g, Min: Machine direction, Cross direction)	-
5.6, Table 1, ix (Tensile index, N.m/g, Min: Machine direction, Cross direction)	-
5.1.1 (plain copier paper)	-
5.3 (Grammage (Substance))	-
5.4 (Thickness)	-
5.5 (Size)	-
5.6, Table 1, i (ISO brightness, percent, Min)	-
5.6, Table 1, ii (Opacity, percent, Min)	-
5.6, Table 1, iii (One minute cobb test, both sides, g/m2 , Max)	-
5.6, Table 1, iv (Surface strength, Dennison (Wax Pick))	-
5.6, Table 1, v (Smoothness for both sides (Bendsten), ml/min, Max)	-
5.6, Table 1, vi (Ash content (at 900 °C), percent by mass, Max)	-
5.6, Table 1, vii (Taber stiffness, Min: Machine direction, Cross direction)	-
5.6, Table 1, viii (Tear Index, mN.m2 /g, Min: Machine direction, Cross direction)	-
5.6, Table 1, ix (Tensile index, N.m/g, Min: Machine direction, Cross direction)	-
5.2 (Moisture)	-

-
-

IS 4990 (2024)

PLYWOOD FOR CONCRETE SHUTTERING WORKS SPECIFICATION (Fourth Revision)

All

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.1 (Timber)	-
Cl-7.1 (Dimensions -length)	-

-
-

IS 9360 (2024)

Carbofuran granules, encapsulated - Specification (first revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description - IS 9360:2024)	-
3.2.2 (Sieve Test (Upper Declared Limit) - IS 6940:1982)	-
3.2.2 (Sieve Test (Lower Declared Limit) - IS 6940:1982)	-
3.2.2 (Ratio of lower to upper limit of sieve size)	-
3.2.3 (Dust 75 Micron sieve- IS 6940:1982)	-
3.2.5 (Moisture content - IS 6940:1982)	-
3.3.1 (Carbofuran Content - IS 9360:2024)	-
3.3.2 (Acidity (as H2SO4) - IS 6940:1982)	-
3.2.4.1 (Attrition Test - IS 9359:2023)	-
3.2.4.2 (Water run-off test - IS 9359:2023)	-

-
-

IS 14756 (2024)

Stainless Steel Utensils - Specification (THIRD REVISION)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3.1 (Material used for manufacturing utensils)	-
Cl 3.2 (Material used for composite bottom)	-
Cl 3.3 (Material used for body of utensil of 3-ply construction)	-
Cl 3.4 (Material used for stainless steel lid)	-
Cl 3.5 (Material used for tempered glass lid)	-
Cl 3.5 (Material used for stainless steel rim)	-
Cl 4.2 & Table 1 (Minimum Sheet Thickness for Body of Utensil)	-
Cl 4.2 & Table 2 (Minimum Sheet Thickness for Lid of Utensil)	-
Cl 4.2 (Thickness of the finished utensil)	-
Cl 4.3 (Classification)	-
Cl 4.4 (i) (Thickness of Aluminium disc/core)	-
Cl 4.4 (ii) (Thickness of Protector/cowl)	-
Cl 4.5 (Minimum sheet thickness (3-ply utensil))	-
Cl 4.5 (Thickness of finished utensil (3-ply utensil))	-
Cl 5.1 (Manufacturing defect & visual appearance)	-
CL 5.2 (Accessibility for cleaning)	-
Cl 5.3 (Joining of handles to the utensils)	-
Cl 5.4 (Requirement for handles)	-
Cl 5.5 (Welding (Finish))	-
Cl 5.6 (Finish of 3-ply utensil)	-
Cl 5.7 (Requirement for coating)	-
Cl 5.8 (Coating thickness test)	-
Cl 5.8 (Coating adhesion test)	-
Cl 5.8.1 (Thermal shock test (Coating))	-
Cl 6.1 (Staining Test (Type Test - Frequency Once in a Year))	-
Cl 6.2 (Mechanical Shock Test (for Cladded Utensils Only))	-
Cl 6.3 (Thermal Shock Test (for Cladded Utensils Only))	-
Cl 6.4 (Dry Heat Test (for Cladded Utensils Only))	-
Cl 6.5 (Coating Thickness Test (for Copper Deposit))	-
Cl 6.6 (Thermal shock test (3-ply construction utensil body))	-
Cl 6.7 (Nominal Capacity Test)	-
Cl 8 (Marking)	-

-
-

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (Material)	-
Cl-4.2 (Carbon content of finished PE lateral pipe)	-
Cl-5.1 (Dimensions of pipes and wall thicknesses)	-
Cl-6.0 (Visual Appearance)	-
Cl-7.2 (Reversion Test)	-
Cl-7.3 (Tensile Test)	-
Cl-7.3.1 (Test Piece)	-
Cl-7.4 (Susceptibility to Environmental Stress Cracking)	-
Cl-8.0 (Supply of pipes)	-
Cl-11 (Marking)	-
3 (Class of Pipe)	-
5.1 & Table 1 (Dimensions of Pipes - Outside diameters)	-
5.1 & Table 1 (Dimensions of Pipes - Wall thickness)	-
6 (Visual Appearance)	-
7.2 (Reversion Test)	-
7.3 (Tensile Strength)	-
7.3 (Elongation at Break)	-
4.2(a) (Carbon Black Content-IS 2530)	-
4.2(b) (Carbon Black Dispersion-IS 2530)	-
4.2(a) (Carbon Black Content-IS 2530)	-
4.2(b) (Carbon Black Dispersion-IS 2530)	-

-
-

IS 164 (2023)

Ready mixed paint for road marking-Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2 (Application ( IS 164 : 2023))	-
5.3 (Durability ( IS 164 : 2023))	-
5.4 (Lead Restriction (lead or compounds of lead or mixtures of both) ( IS 101 : Part 8 : Sec 5 : 2022))	-
5.6.2.1 / 5.5 Table 1 (xx) ("toxic metals such as cadmium, chromium (VI) and their compounds (AAS / ICP) ")	-
5.6.2.2 ( For ECO-Mark) (volatile organic compounds ( IS 101 : Part 2 : Sec 4 : 2022))	-
5.5 Table 1 (i) (Drying time a) Surface dry ( IS 101 : Part 3 : Sec 1 : 1986 ))	-
5.5 Table 1 (i) (Drying timeb) Hard dry ( IS 101 : Part 3 : Sec 1 : 1986 ))	-
5.5 Table 1 (ii) (Consistency ( IS 164 : 2023))	-
5.5 Table 1 (iii) (Finish ( IS 10106 : Part 3 : Sec 4 : 1988))	-
5.5 Table 1 (iv) (Colour (IS 101 : Part 4 : Sec 2 : 2021))	-
5.5 Table 1 (v) (Wet opacity ( IS 101 : Part 4 : Sec 1 : 1988))	-
5.5 Table 1 (vi) (Recoating property ( IS 164 : 2023))	-
5.5 Table 1 (vii) (Resistance to bleeding ( IS 164 : 2023))	-
5.5 Table 1 (viii) (Viscosity (IS 101 : Part 1 : Sec 5 : 1989))	-
5.5 Table 1 (ix) (Viscosity in KU after accelerated stability (IS 101 : Part 1 : Sec 5 : 1989))	-
5.5 Table 1 (xi) (Mass in kg/10 L ( IS 101 : Part 1 : Sec 7 : 2020))	-
5.5 Table 1 (xii) (Keeping properties ( IS 101 : Part 6 : Sec 2 : 1989 ))	-
5.5 Table 1 (xiii) (Early wash out resistance ( IS 164 : 2023))	-
5.5 Table 1 (xiv) (No pick up time ( IS 164 : 2023))	-
5.5 Table 1 (xv) (Non Volatile matter (IS 101 : Part 8 : Sec 2 : 1990))	-
5.5 Table 1 (xv) (Volume solid ( IS 101 : Part 8 : Sec 6 : 1993 ))	-
5.5 Table 1 (xvi) ("Taber Abrasion resistance ( IS 164 : 2023)")	-
5.5 Table 1 (xvii) (Scrub resistance( IS 164 : 2023))	-
5.5 Table 1 (xviii) ("Resistance to accelerated weathering ( IS 164 : 2023)")	-
5.5 Table 1 (xix) (Flexibility ( IS 101 : Part 5 : Sec 2 : 1988))	-
5.5 Table 1 (xxi) (Resistance to wear ( IS 164 : 2023))	-
Cl-5.1 (Composition)	-

-
-

IS 9295 (2024)

STEEL TUBES FOR IDLERS FOR BELT CONVEYORS - SPECIFICATION (second revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
As per Clause 5 (Types /Grade and Designation)	-
As per clause 6 (Material)	-
As per clause 7 (Manufacture)	-
As per clause 7.1.5 (Sulphur)	-
As per clause 7.1.6 (Phosphorus)	-
As per clause 8 (Mechanical Properties)	-
As per clause 8.1 (Tensile Test)	-
As per clause 8.1.1 (Yield Stress)	-
As per clause 8.1.2 (Elongation)	-
As per clause 8.3 (Flattening Test)	-
Cl-9.1, Table-2 (Outside Diameter)	-
As per clause 10 (Hardness Test)	-
As per clause 11 (Mechanical Test)	-
As per clause 13 (Dimension Tolerance)	-
As per clause 14 (Workmanship)	-
As per clause 15 (Straightness)	-
As per clause 16 (Length)	-
As per clause 17 (Surface Protection)	-
As per clause 18 (Marking)	-
Cl-9.1, Table-2 (Thickness)	-
Cl-9.1, Table-2 (Mass)	-
Cl- 13.1.5.1 ("1.Outer dia (08) ")	-
Cl-13.1.5.4 (Thickness (08))	-
Cl-13.1.1 (Ovality (08))	-
Cl- "13.1.5.1, 13.1.5.4 & 13.1.1 " (Avarage Outer dia (08))	-
Cl- "13.1.5.1, 13.1.5.4 & 13.1.1 " (Avarage Thickness (08))	-
Cl- "13.1.5.1, 13.1.5.4 & 13.1.1 " (Maximum Ovality (08))	-

-
-

IS 6406 (2024)

Brilliant blue FCF, food grade - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 and 7 Table 1 (i) (Total dye content - IS 6406:2024)	-
3.2 and 7 Table 1 (iv) (Combined ether extracts- IS 1699:1995)	-
3.2 and 7 Table 1 (iii) (Water Insoluble Matter- IS 1699:1995)	-
3.2 and 7 Table 1 (viii) (Lead - IS 1699:1995)	-
3.2 and 7 Table 1 (ix) (Arsenic- IS 1699:1995)	-
3.2 and 7 Table 1 (viii) (Lead - IS 1699:1995)	-
3.2 and 7 Table 1 (ix) (Arsenic- IS 1699:1995)	-

-
-

IS 15298 : part 4 (2024)

Personal Protective Equipment Part 4 Occupational Footwear (ISO 20347 : 2021, MOD) (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.3.5, Table no 1 of IS 17011,(i) (Allergenic and carcinogenic disperse dyes)	-
Cl 5.3.5, Table no 1 of IS 17011 (ii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl 5.3.5, Table no 1 of IS 17011 (iv) (Chromium (VI))	-
Cl 5.3.5, Table no 1 of IS 17011 (v) (Dimethyl fumarate (DMFU))	-
Cl 5.3.5, Table no1 of IS 17011 (vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl 5.3.5, Table no 1 of IS 17011 (viii) (Organotin compounds)	-
Cl 5.3.5, Table no 1 of IS 17011 (ix) (PCP-TeCP-TriCP polychlorophenols)	-
Cl 5.3.5, Table no 1 of IS 17011 (x) (pH)	-
Cl 5.3.5, Table no 1 of IS 17011 (xi) (Phthalates (each individual phthalate))	-
Cl 5.3.5, Table no 1 of IS 17011 (xii) (Nickel, on skin contact)	-
Cl 5.3.7 (Lead Content ( National Annex A))	-

-
Complete for Chemical ( The material composition of each shoe part must be clearly declared for testing)

IS 15298 : Part 3 (2024)

Personal Protective Equipment Part 3 Protective Footwear (ISO 20346 : 2021, MOD) (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.3.6, Table no 1 of IS 17011 (i) (Allergenic and carcinogenic disperse dyes)	-
Cl 5.3.6, Table no 1 of IS 17011 (ii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl 5.3.6, Table no 1 of IS 17011 (iv) (Chromium (VI))	-
Cl 5.3.6, Table no 1 of IS 17011 (v) (Dimethyl fumarate (DMFU))	-
Cl 5.3.6, Table no1 of IS 17011 (vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl 5.3.6, Table no 1 of IS 17011 (viii) (Organotin compounds)	-
Cl 5.3.6, Table no 1 of IS 17011 (ix) (PCP-TeCP-TriCP polychlorophenols)	-
Cl 5.3.6, Table no 1 of IS 17011 (x) (pH)	-
Cl 5.3.6, Table no 1 of IS 17011 (xi) (Phthalates (each individual phthalate))	-
Cl 5.3.6, Table no 1 of IS 17011 (xii) (Nickel, on skin contact)	-
Cl 5.3.8 (Lead Content ( National Annex A))	-
Cl 5.2 (Design)	-
Cl 5.2.2 (" Height of upper ")	-
Cl 5.3.1.1 (Construction of whole footwear)	-
Cl 5.2.3 (Heel area)	-
Cl 5.3.1.2 (Upper/outsole bond strength)	-
Cl 5.3.2.1 (Toe protection - general)	-
Cl 5.3.2.2 (Internal length)	-
Cl 5.3.2.3 (Width of toecap flange)	-
Cl 5.3.2.4.1 (Corrosion resistance of Class I footwear and hybrid mounted footwear)	-
Cl 5.3.2.4.2 (Corrosion resistance of Class II and hybrid moulded footwear)	-
Cl 5.3.2.6 (Impact resistance)	-
Cl 5.3.2.7 (Compression resistance)	-
Cl 5.3.3 (Leak proofness)	-
Cl 5.3.4 ("Specific ergonomic features ")	-
Cl 5.4.1.1 (Class I footwear, determination of the area where upper requirements apply of Upper)	-
Cl 5.4.1.2 (Hybrid footwear, determination of the area where upper requirements apply of Upper)	-
Cl 5.4.2 (Thickness)	-
Cl 5.4.3 (Tear strength)	-
Cl 5.4.4, Table 11 (Tensile properties- Tensile strength)	-
Cl 5.4.4, Table 11 (Tensile properties- Breaking Force)	-
Cl 5.4.4, Table 11 (Tensile properties-Modulus at 100 % elongation)	-
Cl 5.4.4, Table 11 (Tensile properties- Elongation at break)	-
Cl 5.4.6 (Water vapour permeability and coefficient)	-
Cl 5.6.2 (Tear strength of tongue)	-
Cl 5.4.7 (Resistance to hydrolysis)	-
Cl 5.5.2 (Lining- Tear strength)	-
Cl 5.5.3 (Lining- Abrasion resistance)	-
Cl 5.5.4 (Lining-Water vapour permeability and coefficient)	-
Cl 5.7.1 (Thickness of Insole, insock and footbed)	-
Cl 5.7.2 (Water permeability of insock)	-
Cl 5.7.3 (Water absorption and desorption of Insole, insock and footbed)	-
Cl 5.7.4.1 (Abrasion resistance of Insoles)	-
Cl 5.8.2.1 (Thickness of Outsole)	-
Cl 5.8.2.2 (Cleated area)	-
Cl 5.8.2.3 (Cleat height)	-
Cl 5.8.3 (Outsole- Tear strength)	-
Cl 5.8.4 (Outsole- Abrasion resistance)	-
Cl 5.8.5 (Outsole-Flexing resistance)	-
Cl 5.8.6 (Outsole-Resistance to hydrolysis)	-
Cl 5.8.7 (Interlayer bond strength)	-

-
Complete for Chemical ( The material composition of each shoe part must be clearly declared for testing)

IS 15844 : Part 3 (2024)

Sports Footwear Part 3 Professional Sports Footwear

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-7.12.1, Table no. 1 of IS 17011,(i) (Allergenic and carcinogenic disperse dyes)	-
Cl-7.12.1, Table no. 1 of IS 17011,(ii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv) (Chromium (VI))	-
Cl-7.12.1, Table no. 1 of IS 17011,(v) (Dimethyl fumarate (DMFU))	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl-7.12.1, Table no. 1 of IS 17011,(v) (Dimethyl fumarate (DMFU))	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii) (Organotin compounds)	-
Cl-7.12.1, Table no. 1 of IS 17011,(ix) (PCP-TeCP-TriCP polychlorophenols)	-
Cl-7.12.1, Table no. 1 of IS 17011,(xi) (Phthalates (each individual phthalate))	-
Cl-7.12.1, Table no. 1 of IS 17011,(x) (pH)	-
C-7.12.1, Table no. 1 of IS 17011,(xii) (Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-

-
Complete for Chemical ( The material composition of each shoe part must be clearly declared for testing)

IS 14544 (2022)

LEATHER SAFETY AND PROTECTIVE FOOTWEAR WITH DIRECT MOULDED POLYVINYL CHLORIDE PVC SOLE - SPECIFICATION First Revision

Rs. 20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cL-7.1, Table no 1 of IS 17011 (ii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl-7.1 Table no 1 of IS 17011 (iii) (Aromatic amines released from Azo dyes (each individual amine))	-
Cl-7.1, Table no 1 of IS 17011 (iv) (Chromium (VI))	-
Cl-7.1, Table no 1 of IS 17011 (v) (Dimethyl fumarate (DMFU))	-
Cl-7.1, Table no 1 of IS 17011 (vi) (Formaldehyde (free or released by partial hydrolysis))	-
Cl-7.1, Table no 1 of IS 17011 (viii) (Organotin compounds)	-
Cl-7.1, Table no 1 of IS 17011 (ix) (PCP-TeCP-TriCP polychlorophenols)	-
Cl-7.1, Table no 1 of IS 17011 (x) (pH)	-
Cl-7.1, Table no 1 of IS 17011 (xi) (Phthalates (each individual phthalate))	-
Cl-7.1, Table no 1 of IS 17011 (xii) (Nickel, on skin contact)	-
Cl-7.2 (PVC outsole)	-

-
Complete for Chemical ( The material composition of each shoe part must be clearly declared for testing)

IS 4246 (2025)

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION (Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (General - IS 4246 : 2025)	-
4.1.1 (General - IS 4246 : 2025)	-
5 (Materials - Cl. 5 of IS 5116)	-
5.1.1 (Materials - Toughened glass, if provided,)	-
5.1 (Materials - IS 5116)	-
6.1 (Design for Maintainance)	-
6.2 (Design for Maintainance)	-
6.3 (Design for Maintainance)	-
6.4 (Design for Maintainance)	-
6.5 (Design for Maintainance)	-
6.6 (Design for Maintainance)	-
7.0 (Rigidity and Stability)	-
8.1 (Workmanship and Finish - Cl. 7 of IS 5116)	-
8.2 (Workmanship and Finish -)	-
8.3 (Workmanship and Finish -)	-
9 (Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-
10 (Injector Jets)	-
11.1 (Burners- Cl. 10 of IS 5116)	-
11.2 (Burners)	-
11.3 (Burners)	-
11.4 (Burners)	-
12.1 (Burner Pan Support)	-
12.2 (Burner Pan Support)	-
12.3 (Burner Pan Support)	-
13.1 (Gas Soundness Test - Cl. 16 of IS 5116)	-
13,2 (Gas Soundness Test)	-
13.2 (Gas Leak Detector)	-
14.1 (Gas Inlet Connection - Cl. 18 of IS 5116)	-
14.3 (Gas Inlet Connection)	-

-
-

IS 14166 (2024)

Respiratory protective devices full - Face masks - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.1 (Nominal Values and Tolerances)	-
Cl-5.2 (Materials)	-
Cl-5.3 (Cleaning and Disinfecting)	-
Cl-5.4 (Finish of Parts)	-
Cl-5.5.1 (Mechanical damage)	-
Cl-5.5.2 (Speech diaphragm)	-
Cl-5.5.3 (Tensile force)	-
Cl-5.5.4 (Thermal radiation test)	-
Cl-5.6 (Replaceable Components)	-
Cl-5.7 (Practical Performance)	-
Cl-5.8 (Resistance to Temperature)	-
Cl-5.9.1 (Leakage)	-
Cl-5.9.2 (Compatibility with Skin)	-
Cl-5.10 (Flammability)	-
Cl-5.11 (Resistance to Thermal Radiation)	-
Cl-5.12 (Inward Leakage of Facepiece)	-
Cl-5.13 (Carbon Dioxide Content of the Inhalation Air)	-
Cl-5.14 (Head Harness)	-
Cl-5.14.3.1 (The head harness shall withstand a pull of 100 N)	-
Cl-5.14.3.2 (The head harness shall withstand a pull of 150 N)	-
Cl-5.14.3.3 (Pull of 50 N)	-
Cl-5.15 (Facepiece Connector)	-
Cl-5.15.3 (Strength of Connectors)	-
Cl-5.16.1 (Eyepieces/visors and anti-mist discs)	-
Cl-5.16.3 (Field of vision)	-
Cl-5.16.5 (Impact resistance)	-
Cl-5.17 (Inhalation and Exhalation Valves)	-
Cl-5.17.1 (Inhalation Valves)	-
Cl-5.17.2 (Exhalation Valves)	-
Cl-5.17.3 (Tensile Force)	-
Cl-5.18.1, Table-1 (Inhalation Resistance, mbar)	-
Cl-5.18.1, Table-1 (Exhalation Resistance, mbar)	-
Cl-5.18.2, Table-2 (Inhalation Resistance, mbar)	-
Cl-5.18.2, Table-2 (Exhalation Resistance, mbar)	-
Cl-6 (Test Methods)	-
Cl-7 (Marking)	-

-
-

IS 11569 (2023)

Specification for Cervical Collar (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-3.1 (Material)	-
Cl-3.2 (Sewing Thread)	-
Cl-3.3 (Eyelets)	-
Cl-3.3 (Granules polypropylene)	-
Cl-3.4 (Filling Material)	-
Cl-3.5 (Fasteners, Hook and Loop Tape)	-
Cl-3.6 (Reinforcement Material)	-
Cl-4.1 (Dimensions)	-
Cl-4.2 (Tolerance)	-
Cl-5 (Workmanship and finish)	-
Cl-7 (Marking)	-

-
-

IS 8749 (2024)

Biogas Stove â Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.1 (Fittings and materials)	-
Cl-5.1.1 (Plastic components)	-
Cl-5.2 (stove or parts)	-
Cl-5.3 (Mercurous nitrate test)	-
Cl-5.4 (Body of the burner)	-
Cl-5.5 (i) (Body)	-
Cl-5.5 (ii) (Plug, nuts, and screws)	-
Cl-5.5 (iii) (Pins)	-
Cl-5.5 (iv) (Springs)	-
Cl-5.5 (v) (Washers)	-

-
Exclusion "-; 8.11 Gas taps, (Cl.17) -GAS CONSUMPTION,(Cl.18)-IGNITION AND FLAME TRAVEL, (Cl.19) - FLAME STABILITY , (Cl.20) - NOISE CONTROL, (Cl.21) - FORMATION OF SOOT, (Cl.22) - FLASH BACK , (Cl.23) - COMBUSTION, (Cl.24) a) - SURFACE TEMPERATURE,(Cl.25) -THERMAL EFFICIENCY,"

IS 3623 (2024)

GUIDE AND RUBBING ROPES â SPECIFICATION (Second Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (Size)	-
Cl-4.2 (Length)	-
Cl-5.1 (Material)	-
Cl-5.2 (Tensile strength)	-
Cl-5.3 (Rod or wire)	-
Cl-6 (Breaking load and mass)	-
Cl-7 (Construction)	-
Cl-8.1 (Workmanship)	-
Cl-8.2 (Joints)	-
Cl-8.3 (Lubrication)	-
Cl-9.1 (Round Wire/Rod Ropes)	-
Guide and Rubbing Ropes —Specification (Locked Coil Ropes)	-
Cl-5.1 (Material)	-
Cl-9.2.2 (Reverse Bend Test)	-
Cl-10.1 (completed wire ropes and wires)	-
Cl-10.2 (Test on Wires from the Completed Rope)	-
Cl-10.3 (Breaking Load Test)	-
Cl-13 (Marking)	-

-
-

IS 3745 (2024)

Yoke Type Medical Cylinder Valve with Pin Index Connection ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-3.1 (Chemical Composition- Metallic and non-metallic materials)	-
Cl-3.2.1 (Tensile Strength and Elongation)	-
Cl-3.2.2 (Izod Impact Strength)	-
Cl-3.4 (Protective Finishes)	-
Cl-4 (Design)	-
Cl-4.1 (Design Criteria-Valve)	-
Cl-5.1 (Design Criteria of Pressure Relief Devices)	-
Cl-5.2 (Relief/Bursting Pressure)	-
Cl-6.1 (Cylinder Valve)	-
Cl-6.2 (Yoke)	-
Cl-9.1 (Dimensions - Outlet Connection for Oxygen)	-
Cl-9.2 (Dimensions - Outlet Connection for Oxygen/Carbon Dioxide Mixtures (Carbon Dioxides ≤ 7 percent)	-
Cl-9.3 (Dimensions - Outlet Connection for Oxygen/Helium Mixtures (Helium ≤ 80 percent)	-
Cl-9.4 (Dimensions - Outlet Connection for Ethylene)	-
Cl-9.5 (Dimensions - Outlet Connection for Nitrous Oxide)	-
Cl-9.6 (Dimensions - Outlet Connection for Cyclo-Propane)	-
Cl-9.7 (Dimensions - Outlet Connection for Helium/Oxygen Mixtures (Oxygen ≤ 20 percent)	-
Cl-9.8 (Dimensions - Outlet Connection for Carbon Dioxide/Oxygen Mixtures (Carbon Dioxide ≥ 7 percent)	-
Cl-9.9 (Dimensions - Outlet Connection for Medical Air)	-
Cl-9.10 (Dimensions - Outlet Connection for Special Mixtures of 50 percent Nitrous Oxide and 50 percent Oxygen)	-
Cl-9.11 (Dimensions - Outlet Connection for Nitrogen)	-
Cl-10 (INLET THREADS)	-
Cl-11 (HYDRAULIC BURST PRESSURE TEST)	-
Cl-12 (INTERNAL AND EXTERNAL TIGHTNESS TEST)	-
Cl-13 (VALVING TORQUE TEST)	-
Cl-14 (ENDURANCE TEST)	-
Cl-15 (MARKING)	-
Cl-7 (Basic dimensions for yoke type valve connections)	-
Cl-8 (Alternative Designs of Yoke Type Valve Connections)	-

-
-

IS 9471 : Part 7 (2024)

Modular Lower Limb Orthotic Components â Specification Part 7 Orthotic Joint Bars, Ankle and Knee (Upper and Lower) (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4 (SHAPE AND DIMENSIONS)	-
Cl-5 (MATERIAL)	-
Cl-6 (WORKMANSHIP AND FINISH)	-
Cl-7 (BEND TEST)	-
Cl-8 (MARKING)	-

-
-

IS 9471 : Part 6 (2024)

Modular Lower Limb Orthotic Components â Specification Part 6 Orthotic Hip Joint (Joint Unit, Hip Drop Lock) (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (Joint Body Upper)	-
Cl-4.2 (Joint Hip Lower)	-
Cl-4.3 (Lock Drop Ring)	-
Cl-4.4 (Screw)	-
Cl-4.5 (Nut)	-
Cl-5 (WORKMANSHIP AND FINISH)	-
Cl-6 (FUNCTIONAL REQUIREMENTS)	-
Cl-7 (BEND TEST)	-
Cl-8 (MARKING)	-

-
-

IS 9471 : Part 4 (2024)

Modular Lower Limb Orthotic Components â Specification Part 4 Joint Unit, Ankle (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4 (SHAPE AND DIMENSIONS)	-
Cl-4.4 (Depth of Slot)	-
Cl-5.1 (strength heat)	-
Cl-5.2 (screws)	-
Cl-5.3 (steel annealed bars)	-
Cl-5.4 (steel)	-
Cl-5.5 (spring)	-
Cl-6 (WORKMANSHIP AND FINISH)	-
Cl-7 (HEAT TREATMENT)	-
Cl-8 (Marking)	-

-
-

IS 9471 : Part 3 (2024)

Modular Lower Limb Orthotic Components â Specification Part 3 Stirrup Plates (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-3 (SHAPE AND DIMENSIONS)	-
Cl-4.1 (Plate)	-
Cl-4.2 (Channel)	-
Cl-5 (FABRICATION)	-
Cl-6 (WORKMANSHIP AND FINISH)	-
Cl-7 (MARKING)	-

-
-

IS 64 (2023)

Barium sulphate pigments for paints - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.1 (Form and Condition)	-
Cl-5.2 (Lead Restriction)	-
Cl-5.4, Table 1 (i) (a) (Barium (as BaSO4), percent by mass, Min)	-
Cl-5.4, Table 1 (i) (b) (Carbonates (as BaCO3), percent by mass, Max)	-
Cl-5.4, Table 1 (ii) (Volatile matter, percent by mass, Max)	-
Cl-5.4, Table 1 (iii) (Residue on sieve, percent by mass, Max)	-
Cl-5.4, Table 1 (iv) (Oil absorption)	-
Cl-5.4, Table 1 (v) (Colour)	-
Cl-5.4, Table 1 (vi) (Matter soluble in water, percent by mass, Max)	-
Cl-5.4, Table 1 (vii) (pH of the aqueous extract)	-
Cl-5.4, Table 1 (viii) (Relative density at 25/25 °C,)	-

-
All except Toxic Heavy Metal Restriction

IS 4581 (2021)

PHOSPHORUS TRICHLORIDE PURE AND ANALYTICAL REAGENT-SPECIFICATION Second Revision IS 4581

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Description)	-
4.2 , Table No. 1 , i) (Phosphorus trichloride, (as PCl3 ))	-
4.2 , Table No. 1 , iii) (Relative density)	-
4.2 , Table No. 1 , iv) (Evaporation residue, including PCl5)	-
4.2 , Table No. 1 , v) (Sulphate (as SO4 ))	-
4.2 , Table No. 1 , vi) (Heavy metals (as Pb))	-
4.2 , Table No. 1 , vii) (Iron (as Fe),)	-
4.2 , Table No. 1 , viii) (Arsenic,)	-

-
Test facility for Boiling Range not available

IS 6046 (2023)

Gypsum for agricultural use - Specification (second revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-3.1 (Fineness - Cl. 3 of IS 1288)	-
Cl-3.2 Table 1 (Calcium Sulphate Dihydrate - Annex B of IS 6046)	-
Cl-3.2 Table 1 (Sodium Content( as Na) - Annex C of IS 6046)	-

-
-

IS 2923 (2024)

Carmoisine, food grade - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 and 7 Table 1 (i) (Total dye content - IS 2923:2024)	-
3.2 and 7 Table 1 (ii) (Loss on drying at 135° C and Chlorides and sulphates - IS 1699: 1995)	-
3.2 and 7 Table 1 (iii) (Water Insoluble Matter- IS 1699:1995)	-
3.2 and 7 Table 1 (iv) (Combined ether extracts- IS 1699:1995)	-
3.2 and 7 Table 1 (v) (Subsidiary dyes- IS 2923:2024)	-
3.2 and 7 Table 1 (vi) (Dye Intermediates- IS 2923:2024)	-
3.2 and 7 Table 1 (vii) (Unsulphonated primary aromatic amines- IS 2923:2024)	-
3.2 and 7 Table 1 (viii) (Lead - IS 1699)	-
3.2 and 7 Table 1 (ix) (Arsenic - IS 1699)	-
3.2 and 7 Table 1 (x) (Mercury - IS 1699)	-
3.2 and 7 Table 1 (xi) (Copper - IS 1699)	-
3.2 and 7 Table 1 (xii) (Chromium - IS 1699)	-
3.2 and 7 Table 1 (xiii) (Cadmium - IS 1699)	-

-
-

IS 5405 (2025)

Disposable Sanitary Napkin/Panty Liner/Maternity Pad/Period Panty - Specification ( Third Revision )

Rs 12955/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.3.1 (Bacterial and Fungal Bioburden)	-
7.3.2 (Staphylococcus aureus)	-
5 (Sizes)	-
Cl. 5 Table-1 (Length (Absorbent core only))	-
Cl 7.5 (Phthalate test- Combination)	-
7.1 (pH Test)	-
Cl 7.5 (Phthalate test- Di-iso-butyl phthalate (DIBP))	-
7.2 ("Ability to Withstand Pressure after Absorption: Liquid Absorption ml, Min")	-

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List