BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

999 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

991

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

- View breakup
Rs. 4250/-(Excluding leakage test and Hyd. Proof Test)+Testing charges as per IS 14151(Part 1)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2.1 (Visual and Workmanship Requirement)	-
4.2.7 (1 Dimensions of Quick Coupled Pipes and Fittings)	-

-
-

992

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 iv (Loss on ignition - Cl 7.1 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- i (Fineness 4031 Part 2)	-

-
Excluding Table 1,Clause 6 ,sl. no.(vi) , alkali content;

993

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1 (Colour)	-
10.1 (Surface Finish)	-
7.2.1.1 Table3 (Angle of taper (Note-1))	-
5 (CLASSIFICATION OF PIPES)	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Minimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. Variation)	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-
7.1.1.2 (DIMENSIONS-PIPE-Ovality (Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Minimum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Average Thickness)	-
Cl- 7.2 (Socket length (Take 4 reading & minimum will be reported))	-
7.2.1 (DIMENSIONS-Socket)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-
7.2.1.2(a)-Table 5 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-
10.7 (Sulphated Ash Content)	-
7.2.1.2-Table 4 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-
8 (SEALING RINGS)	-
9.1 (PIPE ENDS)	-
10.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.1.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.2 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-
10.4 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-
10.5 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-
10.6 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-
11.1-Table 6 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-
11.1-Table 6 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-
11.2 (Resistance to External Blows at 0°C)	-
13.1 (Marking)	-
cL-13.1.1 (Marking)	-
Cl-13.1.2 (Marking)	-

-
Excluding Effect on water

994

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 8.3 (Carbon Black Content)	-
Cl-7.4 (Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-
8.2 (Longitudinal Reversion Test)	-
Cl 8.3 (Carbon Black Dispersion)	-
8.7 (Density)	-
8.4 ( Melt Flow Rate)	-
7.4.1.2 (Ovality)	-
7.2 (Length)	-
6.2 (Colour)	-
6.2.1 (6.1.1 Identification Stripes)	-

-
Excluding Oxidation induction , overall migration, Cl 8.7 density, Cl 7.4.1.2 ovality Cl 8.8 Tensile,Cl 8.9 Elongation at Break;

995

IS 2202 : Part 1 (2023)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Seventh Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (GRADE)	-
4 (Grade, Type and Construction)	-
7.3.2 (CONSTRUCTION-Stiles and Rails)	-
11.1 (Dimensions - Height)	-
11.1 (Dimensions - Width)	-
11.1 (Dimensions - Thickness)	-
11.1 (Dimensions - Variation in thickness)	-
11.12 (End immersion test)	-
11.1 (Dimensions - Squareness)	-
9.1 (Workmanship & Finish)	-
9.2 (Workmanship & Finish)	-
9.3 (Workmanship & Finish)	-
11.2 (General Flatness Test)	-
11.3 (Local Planeness Test)	-
Clause 11.4 (Impact Indentation Test)	-
11.5 (Flexure Test)	-
11.6 (Edge Loading Test)	-
11.7.1 (Shock Resistance Test)	-
11.7.2 (Shock Resistance Test)	-
Clause 11.8 (Buckling Resistance Test)	-
Clause 11.9 (Slamming Test)	-
Clause 11.10 (Misuse Test)	-
Clause 11.11 (Varying Humidity Test)	-
11.13 (Knife Test)	-
Clause 11.14 (Glue Adhesion Test)	-
Clause 11.15 (Screw Withdrawal Resistance Test)	-
7.3.3 (CONSTRUCTION-Stiles and Rails)	-

-
Excluding Test facility not available for Cl 11.2, 11.4, 11.6, 11.8, 11.9;

996

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

Rs. 5250/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Workmanship)	-
Cl 10.2 (Workmanship)	-
Cl 10.3 (Workmanship)	-
Cl 11 (Length, Width & Thickness)	-
6.1 (Carbon %)	-
6.1 (Sulphur %)	-
6.1 (Phosphorus %)	-
6.1 (Silicon %)	-
6.1 ( Aluminium %)	-
6.1 ( Nitrogen%)	-
6 (Sulphur + Phosphorus)	-
6.1 ( Nb)	-
6.1 (V)	-
6.1 ( Ti)	-
6 (carbon equivalent (CE))	-
6 (Copper as Cu)	-
Clause 6, Table 1 Note : 3 (Nb+V+Ti)	-
6.1 (Cr)	-
6.1 (Mo)	-
6.1 (Ni)	-
Cl 6.1 (Manganese)	-

-
-

997

IS 1659 (2004)

Block boards - Specification (Fourth Revision)

- View breakup
BWP Grade 6500/- MR Grade 5400/- Testing Charges for Spot Test Only(Cl.9.2.6)-725/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.2.6 (Spot test - Annexure L)	-
9.2.5 (Modulus of elasticity - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of elasticity - AVERAGE - Annexure K)	-
9.2.5 (Modulus of rupture - MINIMUM INDIVIDUAL - Annexure K)	-
9.2.5 (Modulus of rupture - AVERAGE - Annexure K)	-
9.2.4 (Mycological Test [for MR grade only] - Annexure J)	-
9.2.3 (Adhesion of Plies - Annexure H)	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For MR Grade])	-
9.2.2 (Resistance to water - Annexure G, Annexure H [For BWP grade])	-
9.2.1 (Dimensional Changes caused by humidity Change in local planeness - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Delamination - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in thickness - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Thickness - at 90% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 40% RH - Annexure F)	-
9.2.1 (Dimensional Changes caused by humidity - Change in Length - at 90% RH - Annexure F)	-
7.3 (Dimensional Requirements - Variation in thickness - Annexure E)	-
7.3 (Dimensional Requirements - Squareness - Annexure D)	-
7.3 (Dimensional Requirements - Edge Straightness - Annexure D)	-
7.3 (Dimensional Requirements - Thickness - Annexure E)	-
7.3 (Dimensional Requirements - Width - 8.1.4)	-
7.3 (Dimensional Requirements - Length - 8.1.4)	-
8.1.3, 6.3.3, IS 1328 (Visual Inspection - Permissible Defects - IS 1328 [test method for DECORATIVE type])	-
8.1.3, 6.3.3, IS 303 (Visual Inspection - Permissible Defects - IS 303 [test method for COMMERCIAL type])	-
9.2.6 (mechanical) (Spot test - Annexure L)	-

-
SIZE: One Block Board Sample Size without dimensional measurements:Length-1200 mm, width-1200

998

IS 13334 : Part 1 (2014)

Skimmed milk powder - Specification: Part 1 standard grade (Second Revision)

10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.6 (Bacterial count)	-
5.6 (Coliform count )	-
5.6 (Escherichia coli)	-
5.6 (Coagulase positive Staphylococcus aureus)	-
5.6 (Salmonella)	-
5.6 (Spore count, Aerobic (Bacillus cereus))	-
5.6 (Spore count, Anaerobic (Sulfite reducing Clostridia))	-
5.6 (Listeria monocytogenes)	-
4 (Description)	-
Cl 5.1 (Milk intended (IS 1479 - Part 1))	-
5.2 (Absence of extraneous matter, added colour and added flavour)	-
Cl 5.3 (Calcium chloride, citric acid and sodium citrate, sodium salts of orthophosphoric acid and polyphosphoric acid (as linear phosphate), )	-
Cl 5.4 (The flavour of the product or of the reconstituted milk shall be pleasant and clean (see IS 10030).)	-
5.6 (Moisture)	-
5.6 (Milk protein in milk solids not fat)	-
5.6 (Milk fat)	-
5.6 (Insolubility index)	-
5.6 (Milk fat)	-
5.6 (Titratable acidity (lactic acid))	-
5.6 (Scorched particles)	-
5.6 (Total ash (on dry basis))	-
5.6 (Coliform count )	-
5.6 (Salmonella)	-
5.6 (Bacterial count)	-

-
500 gm x 3

999

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

- View breakup
Electricity Cost (per kWh) ₹ 9.00 Testing Charges per man hour ₹ 300.00 Total testing charge for BWP Grade ₹ 7,456.00 ₹ 7,450.00 Total testing charge for BWR Grade ₹ 7,108.00 ₹ 7,100.00 Total testing charge for MR Grade ₹ 7,090.00 ₹ 7,100.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4 (Grades)	-
Cl-8.1 (Dimensions -length)	-
Cl.8.1 (Dimensions -width)	-
Cl-8.2 (Thickness of the plywood boards)	-
Cl-8.3 (Squareness)	-
Cl.8, 8.3 & Annex C (Edge Straightness)	-
Cl-11.4 (Moisture Content)	-
Cl-11.3.2 (Mycological Test)	-
Cl-11.5, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-
Cl-11.5, Table 4 (Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4, (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-
Cl-11.5, Table-4 (Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-
Cl-11.3.1, 11.3.1.1 (Water Resistance Test)	-
Cl-9 (WORKMANSHIP AND FINISH)	-

-
Excluding- Steady State Formaldehyde Emission Test (Cl. 11.7)

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List