BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

994 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

451

IS 428 (2013)

Washable distemper - Specification (Third Revision)

Type-1 3,760 Type-2 3,830 View breakup
For Initial testing: Oil Emulsion (Type-1) = Rs. (2625+828+300) = Rs. 3,753 = Rs. 3,760 Plastic (Type-2) = Rs. (2700+828+300) = Rs. 3,828 = Rs. 3,830 Only Keeping Properties: Oil Emulsion (Type-1) = Rs. (2550+828+300) = Rs. 3,678 = Rs. 3680 Plastic (Type-2) = Rs. (2625+828+300) = Rs. 3,753 = Rs. 3,760 For Initial Testing With ECO-Mark Requirements (Excluding Keeping Properties): Oil Emulsion (Type-1) = Rs. (5025+855+550) = Rs. 6,430 Plastic (Type-2) = Rs. (5100+855+550) = Rs. 6,505= Rs. 6,510 Preparation of Test Report = Rs. 300.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.9.2.2 ( Chromium VI and its compund (Requirement for Eco-Mark))	-
Cl. 6.9.2.2 (Cadmium (Requirement for Eco-Mark))	-
Cl. 6.9.2.2 (Lead (Requirement for Eco-Mark))	-
Cl. 6.9.2.1 (Volatile organic compounds (Requirement for Eco-Mark))	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. ix) (Accelerated storage stability)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. viii) (Resistance to alkali)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. vii) (Recoating Properties)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. vi) (Residue on sieve, Type 2)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. vi) (Residue on sieve, Type 1)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. v) (Fastness to light)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. iv) (Colour)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. iii) (Finish)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. ii) (Consistency )	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. i) b) (Drying Time a) Hard Dry, Type 2)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. i) b) (Drying Time a) Hard Dry, Type 1)	-
Cl.6.6, Cl.6.7 and 9.1 - Table 1 - Sl. No. i) a) (Drying Time a) Surface Dry, Type 2)	-
Cl.6.6 (Keeping Proterties)	-
Cl.6.5 (Lead Restriction)	-
Cl.6.3 (Application)	-
Cl.6.2 (Thining)	-
Cl.6.1 (Foam and condition)	-

-
Approved sample for finish and colour parameter is required, Weatherometer for fastness to light parameter; EXCLUDING Finish, colour, Fastness to light;

452

IS 2494 : Part 1 (1994)

V - Belts - Endless V - Belts for industrial purposes: Part 1 general purpose - Specification (Second Revision)

Rs.3000.00. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1 (Elongation)	-
10.1 (Tensile Strength)	-
7.2.2 (Matched Belts - Code)	-
7.2.1 (Matched Belts - Difference)	-
7.1 (Belt Pitch Length)	-
6.0 (Designation)	-
5 Table 2B (Cross sectional dimension)	-
5 Table 2B (Cross sectional dimension)	-
5 Table 2A (Cross sectional dimension)	-
5 Table 2A (Cross sectional dimension)	-
5 Table 2A (Cross sectional dimension)	-
5 Table 2A (Cross sectional dimension)	-
5 Table 2A (Cross sectional dimension)	-
5 Table 2A (Cross sectional dimension)	-
5 Table 2A (Cross sectional dimension)	-
5 Table 2A (Cross sectional dimension)	-
5 Table 1 (Cross sectional dimension)	-
5 Table 1 (Cross sectional dimension)	-
5 Table 1 (Cross sectional dimension)	-
5 Table 1 (Cross sectional dimension)	-

-
EXCLUDING -; Only Dimension test Avalible

453

IS 7904 (2018)

High carbon steel wire rods - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1,(Clauses 5.1 and 7.2) (Carbon)	-
Table-1,(Clauses 5.1 and 7.2) (Sulphor)	-
Table-1,(Clauses 5.1 and 7.2) (Phosphorous)	-
Table-1,(Clauses 5.1 and 7.2) (Manganese)	-
Table-1,(Clauses 5.1 and 7.2) (Silicon)	-
Table-1,(Clauses 5.1 and 7.2) (Aluminium)	-
Table-1,(Clauses 5.1 and 7.2) (Chromium)	-
Table-1,(Clauses 5.1 and 7.2) (Nickel)	-
Table-1,(Clauses 5.1 and 7.2) (Molybdenum)	-
Table-1,(Clauses 5.1 and 7.2) (Copper)	-
Table-1,(Clauses 5.1 and 7.2) (Boron)	-
Table-1,(Clauses 5.1 and 7.2) (Vanadium)	-
Table-1,(Clauses 5.1 and 7.2) (Titanium)	-
Table-1,(Clauses 5.1 and 7.2) (Nitrogen)	-
Table-1,(Clauses 5.1 and 7.2) (S+P)	-
Cl 9 (Dimensions & tolerances) ()	-

-
Grade of Steel as per Table 1, Information wrt Micro Alloy addition and type of killing may also be declared. Sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm can only be tested.; EXCLUDING -; i] cl 12 surface defects, ii] cl 13 decarburization test, iii] cl 14 non-metallic inclusions, iv] cl 15 microstructure

454

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

Rs- 5850.0 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (chem) (MATERIAL)	-
4.6.2 (TRANSPARANCY)	-
4.6.3 (LEAKAGE TEST)	-
4.6.4 (DROP TEST)	-
4.6.4, clause 8 of IS:2798:1998 (Drop test )	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- c. Air pressure leakage)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- a. Closure leakage )	-
4.6.2 Annex A (Transparency)	-
4.5, IS:2798:1998 (Wall thickness- Bottom, in mm)	-
4.5, IS:2798:1998 (Wall thickness- Middle , in mm)	-
4.5, IS:2798:1998 (Wall thickness- Top , in mm )	-
4.4 , clause 5 of IS:2798:1998 (Brimful capacity in ml)	-
4.3 (Workmanship, Finish & Appearance)	-
4.2 (Design, Shape & Dimension )	-
4.6.5 (MIGRATION TEST)	-
4.6.6 (PORTABILITY TEST)	-
4.1 (Material)	-
4.6.6 (chem) (Water Potability test (after 30 days) (a) Taste (b) Odour)	-
4.6.5.1 (chem) (Colour migration (Container))	-
4.6.5.1 (chem) (Colour migration (Caps))	-
4.6.5 , IS:9845:1998 (chem) (Migration- b. Amount of extractive)	-
4.6.5 , IS:9845:1998 (chem) (Migration- a. Amount of extractive)	-
4.6.5.1 (chem) (Colour migration (Caps))	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- b. Vibration leakage)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(i) (Specific migration for Cap,Barium)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(ii) (Specific migration for Cap,Cobalt)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(iii) (Specific migration for Cap,Copper)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(iv) (Specific migration for Cap,Iron)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(v) (Specific migration for Cap,Lithium)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(vi) (Specific migration for Cap,Manganese)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(vii) (Specific migration for Cap,Zinc)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(viii) (Specific migration for Cap,Antimony)	-
Clauses 4.6.7.2 and 4.6.7.3 ,S.No(ix) ("Specific migration for Cap,Phthalic acid, bis(2-ethylhexyl) ester (DEHP)")	-

-
200 ml & 250 ml (50 Empty Bottle + 80 Caps), 500 ml & 1 Litre (30 Empty Bottle + 80 Caps), 2 Litre (15 Empty Bottle + 80 Caps), 5 Litre ( 10 Empty Bottle + 40 Caps), 20 Litre (06 Empty Jar + 40 Caps)

455

IS 1746 (1992)

Shoe polish, paste - Specification (Third Revision)

Rs 8700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1 (Odour)	-
4.1.2 (Colour)	-
4.1.3 (Consistency)	-
4.1.4 (Applicability)	-
4.1.6 (colour of water extract)	-
4.2 (table 1 S.no(i)) (Softeing point of non-volatile matter)	-
4.2 (table 1 S.no(ii)) (Ash of the non-volatile matter)	-
4.2 (table 1 S.no(iii)) (pH of water extract )	-
4.2 (table 1 S.no(v)) (Flash point of volatile portion,)	-
4.2 (table 1 S.no(vi)) (Non-volatile matter )	-

-
EXCLUDING DISTILLATION RANGE;

456

IS 513 : Part 2 (2016)

Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (CARBON)	-
6.0 (SULPHUR)	-
6.0 (PHOSPHORUS)	-
6.0 (MANGANESE)	-
6.0 (SILICON)	-
6.0 (ALUMINIUM)	-
6.0 (NITROGEN)	-
6.0 (MICRO ALLOYS)	-
Cl 7 (UTM)	-
Cl 7 (UTM)	-
Cl 10 (Length, Width & Thickness)	-
Cl. 10 (Out of square)	-
Cl. 10 (Flatness)	-
Cl. 10 (Camber)	-
Cl. 10 (Width (04))	-
Cl. 10 (Thickness (08))	-
Cl. 8.5.3 Table 6 (Surface Roughness)	-
Cl. 7.2 Table 7 (Bend Test)	-
Cl 8.5 (Workmanship)	-
9 (Freedom from defects)	-

-
sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm c; EXCLUDING Complete for thickness > 0.8 mm, only C& S can be tested for thickness < 0.8 mm;

457

IS 4320 (1982)

Specification for thiram, technical

Rs 2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Description)	-
2.2 Table 1 (Loss on drying at 60°C)	-
2.2 Table 1 (Bis ( dimethylthiocarbamoyl ) disulphide)	-
2.2 Table 1 (Ash content)	-

-
-

458

IS 15500 : Part 1 to 8 (2004)

Deepwell handpumps, components and special tools - Specification

Rs 4500/- + Charges as per relevant material standards View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2/2.3,(Refer 15500(Part 1 to 8)& 5 (Part 1) (Raw material)	-
2/2.3,(Refer 15500(Part 1 to 8)& 9.4 (Part 1) (Dimensions & critical dimensions in conformance with the relevant figures in Part 4.)	-
2/2.3,(Refer fig 4.1 of Part4) & 9.4 (Part 1) (Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-
2/2.3,(Refer fig 4.2 of Part4) (Dimensions of FIG. 4,2 HEAD— EWDP)	-
2/2.3,(Refer fig 4.3A of Part4) (Dimensions of Fig 4.3A Side Plate)	-
2/2.3,(Refer fig 4.3B of Part4) (Dimensions of Fig 4.3B Head Flange)	-
2/2.3,(Refer fig 4.3C of Part4) (Dimensions of Fig 4.3C Back Plate —Standard (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3D of Part4) (Dimensions of Fig 4.3D Bracket — Standard (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3E of Part4) (Dimensions of Fig 4.3E Back Plate — EDWP)	-
2/2.3,(Refer fig 4.3F of Part4) (Dimensions of Fig 4.3F Bracket — EDWP)	-
2/2.3,(Refer fig 4.3G of Part4) (Dimensions of Fig 4.3G Axle Bust — Right)	-
2/2.3,(Refer fig 4.3H of Part4) (Dimensions of Fig 4.3H Axle Bust — Left)	-
2/2.3,(Refer fig 4.3I of Part4) (Dimensions of Fig 4.3 I Front Top End Plate)	-
2/2.3,(Refer fig 4.3IJof Part4) (Dimensions of 4.3J Front Bottom End Plate)	-
2/2.3,(Refer fig 4.3IKof Part4) (Dimensions of Fig 4.3K Gusset — Standard w (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3L Jof Part4) (Dimensions of Fig 4.3L Gusset — EDWP (For EDWP) )	-
2/2.3,(Refer fig 4.4 Jof Part4) (Dimensions of FIG. 4.4 FRONTCOVER)	-
2/2.3,(Refer fig 4.5A of Part4) (Dimensions of FIG. 4.5A Flange for Third Plate)	-
2/2.3,(Refer fig 4.5 B of Part4) (Dimensions of FIG. 4.5B Guide Bush )	-
2/2.3,(Refer fig 4.6 of Part4) (Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.7 of Part4) (Dimensions of FIG.4.7 HANDLE— EDWP)	-
2/2.3,(Refer fig 4.8A of Part4) (Dimensions of FIG 4.8A Handle Bar — Standard (For SDWR VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.8B of Part4) (Dimensions of FIG 4.8B Handle Bar — EDWP)	-
2/2.3,(Refer fig 4.8C of Part4) (Dimensions of FIG 4.8C Chain Guide)	-
2/2.3,(Refer fig 4.8 D of Part4) (Dimensions of Fig 4.8D Bearing Housing )	-
2/2.3,(Refer fig 4.9 of Part4) (Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-
2/2.3,(Refer fig 4.10 of Part4) (Dimensions of FIG. 4.10 T-BAR (For EDWP only))	-
2/2.3,(Refer fig 4.11 of Part4) (Dimensions of FIG; 4.11 COUNTER WEIGHT (For EDWP only))	-
2/2.3,(Refer fig 4.12A of Part4) (Dimensions of Fig 4.1 2A Telescopic Stand — Standard (For borewell with 150 NB casing pipe)(For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.12B of Part4) (Dimensions of Fig 4.12B Normal Stand — Standard (For borewell with 1001125 NB casing pipe) (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.13A of Part4) (Dimensions of Fig 4.1 3A Telescopic Stand — EDWP (For borewell with 150 NB casing pipe) FOR EDWP )	-
2/2.3,(Refer fig 4.14 A of Part4) (Dimensions of Fig 4.1 4A Stand Pipe — Standard (For SDWP, VLOM-65, VLOM-50))	-
2/2.3,(Refer fig 4.14 B of Part4) (Dimensions of Fig 4.14B Stand Pipe — EDWP (For EDWP))	-
2/2.3,(Refer fig 4.14 C of Part4) (Dimensions of Fig 4.14C Stand Flange)	-
3/3.3.1,(Refer Cl 9.4.1 and 9.4.3 15500(Part 1 ) (Head and Cylinder Assemblies)	-
6.1 of Part 1 ,refer Condition 4 of IS 1573 (Electro-galvanizing )	-
6.2 of Part 1 ,Refer IS 4759 (Galvanizing)	-
6.2.1 of Part 1,Refer Cl 5.9 of IS 2629 (Galvanizing)	-
9.4/9.4.1.1 of part 1 (Dimensional and Other Tests/head assembly )	-
9.4/9.4.1 .2 of part 1 (Head assembly )	-
9.4/9.4.1 .2 of part 1 (handle shall be checked for lateral play at the end of the square section of handle on either side)	-
9.4/9.4.1.2 of part 1 (The clearance between the handle and the bracket )	-
9.4/9.4.1 .2 of part 1 (The stroke of the pump )	-
9.4/9.4.2.1 of part 1 (Handle Assembly)	-
9.4/9.4.2.1 of part 1 (Handle Assembly)	-
9.4/9.4.3of part 1 (Cylinder Assembly )	-
9.4/9.4.3of part 1 (Cylinder Assembly )	-
9.4/9.4.3of part 1 (Cylinder Assembly )	-
9.4/9.4.3of part 1 refer table 3 (Discharge of Pump)	-
9.4/9.4.4of part 1 (Valve Assemblies)	-
2/2.3 ,Refer Fig 3.1 (Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-
2/2.3 ,Refer Fig 3.1 (Dimensions of FIG. 4.4 FRONT COVER)	-
2/2.3 ,Refer Fig 3.1 (Dimensions of FIG. 4.24 HANDLE AXE )	-
2/2.3 ,Refer Fig 3.1 (Dimensions of FIG.4.27 WASHER)	-
2/2.3 ,Refer Fig 3.1 and Refer annex B ( HexagonaI Nut — )	-
2/2.3 ,Refer Fig 3.1 and Refer annex B (Hexagonal Bolt)	-
2/2.3 ,Refer Fig 3.1 and 3.2 (Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3 ,Refer Fig 3.1 and 3.2 (Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-
2/2.3 ,Refer Fig 3.1 and 3.2 (Dimensions of FIG. 4.26 BEARING SPACER)	-
2/2.3 ,Refer Fig 3.3 and 3.4 (Prevailing Torque Type Hex. Nut,)	-
2/2.3 ,Refer Fig 3.1 and 3.2,Annex B (Hex. Bolt)	-
2/2.3 ,Refer Fig 3.3 (Dimensions of FIG. 4,2 HEAD— EWDP)	-
2/2.3 ,Refer Fig 3.3 (Dimensions of FIG. 4.4 FRONT COVER)	-
2/2.3 ,Refer Fig 3.3 (Dimensions of FIG. 4.24 HANDLE AXE )	-
2/2.3 ,Refer Fig 3.3 (Dimensions of FIG.4.27 WASHER)	-
2/2.3 ,Refer Fig 3.3 and annex B (Hexagonal Nut—)	-
2/2.3 ,Refer Fig 3.3 and annex B (Hexagonal Bolt)	-
2/2.3 ,Refer Fig 3.3 and 3.4 (Dimensions of FIG.4.7 HANDLE— EDWP)	-
2/2.3 ,Refer Fig 3.3 and 3.4 (Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-
2/2.3 ,Refer Fig 3.3 and 3.4 (Dimensions of FIG. 4.26 BEARING SPACER)	-
2/2.3 ,Refer Fig 3.3 and 3.4 (Prevailing Torque Type Hex. Nut,)	-
2/2.3 ,Refer Fig 3.3 and 3.4 (Hex. Bolt —)	-
2/2.3 ,Refer Fig 3.3 and 3.4 (Ball bearing, single side shielded)	-
2/2.3 ,Refer Fig 3.5 (Dimensions of FIG. 4.22 PLUNGER ROD — STANDARD (For SDWP))	-
2/2.3 ,Refer Fig 3.5 (Dimensions of FIG. 5.1 CYLINDER BODY— STANDARD (For SDWP))	-
2/2.3 ,Refer Fig 3.5 (Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-
2/2.3 ,Refer Fig 3.5 (Dimensions of FIG. 6.1 BRASS LINER)	-
2/2.3 ,Refer Fig 3.5 (Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 6.6 FOLLOWER — SDWP )	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 6.12 CHECK VALVE SEAT— STAN~AR~ (For SDWP & EDWP))	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.5 and 3.6 (Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-
2/2.3 ,Refer Fig 3.7 (Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-
2/2.3 ,Refer Fig 3.7 (Dimensions of FIG. 5.2 CYLINDERBODY— LONG (For EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.7 (Dimensions of FIG. 5.5 A Upper CAPS— VLOM-65 (For SDWP & EDWP))	-
2/2.3 ,Refer Fig 3.7 (Dimensions of FIG. 5.5 B Bottomr CAPS— VLOM-65 (For SDWP & EDWP))	-
2/2.3 ,Refer Fig 3.7 (Dimensions of FIG. 6.1 B BRASS LINER)	-
2/2.3 ,Refer Fig 3.7 (Dimensions of FIG. 7.4 SEALING RING— VLOM-65)	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 6.8 FOLLOWER— VLOM-65)	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 6.10 CHECKVALVE— VLOM-65)	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 6.13 CHECK VALVE — VLOM-65)	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 6.14 CAGE (For VLOM-65))	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 7.8 LOWERVALVE SEATING— VLOM-65 68)	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Dimensions of FIG. 7.10 O-RING— VLOM-65)	-
2/2.3 ,Refer Fig 3.7 and 3.8 (Check Nut)	-
2/2.3 ,Refer Fig 3.9 (Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-
2/2.3 ,Refer Fig 3.9 (Dimensions of FIG. 5.3 CYLINDERBODY— VLOM-50)	-
2/2.3 ,Refer Fig 3.9 (Dimensions ofFIG. 5.6 CYLINDERCAPS— VLOM-50)	-
2/2.3 ,Refer Fig 3.9 (Dimensions of FIG. 6.1 C BRASS LINER)	-
2/2.3 ,Refer Fig 3.9 (Dimensions of FIG. 7.5 SEALINGRING— VLOM-50)	-
2/2.3 ,Refer Fig 3.9 and 3.10 (Dimensions of FIG. 6.15 PLUNGERVALVE BODY— VLOM-50)	-
2/2.3 ,Refer Fig 3.9 and 3.10 (Dimensions of FIG. 6.16 CHECKVALVE BODY— VLOM-50)	-
2/2.3 ,Refer Fig 3.9 and 3.10 (Dimensions of FIG. 7.2 PUMP BUCKET — VLOM-50)	-
2/2.3 ,Refer Fig 3.9 and 3.10 (Dimensions of FIG. 7.9 BOBBIN)	-
2/2.3 ,Refer Fig 3.9 and 3.10 (Dimensions of FIG. 7.11 O-Ring — VLOM-50)	-
2/2.3 ,Refer Fig 3.9 and 3.10 (Hexagonal Nut)	-
2/2.3 ,Refer Fig 3.9 and 3.10 (Hexagonal Bolt)	-
2/2.3 ,Refer Fig 3.11 (Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-
2/2.3 ,Refer Fig 3.11 (Dimensions of FIG. 5.2 CYLINDERBODY— LONG (For EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.11 (Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-
2/2.3 ,Refer Fig 3.11 (Dimensions of FIG. 6.1 B BRASS LINER)	-
2/2.3 ,Refer Fig 3.11 (Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG.6.5 BUCKET SPACER — LOWER (For EDWP))	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 6.7 FOLLOWER— EDWP)	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 6.13 CHECK VALVE — VLOM-65)	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-
2/2.3 ,Refer Fig 3.11 and 3.12 (Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-

-
-

459

IS 13049 (1991)

diaphragm type (plastic body) float operated valves for cold water services

Rs.6000.00 excluding material and chemical test. View breakup
Rs.6000.00 excluding material and chemical test.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (NOMINAL SIZE- )	-
6-6.1 (MANUFACTURE AND WORKMANSHIP)	-
6-6.2 (MANUFACTURE AND WORKMANSHIP)	-
7-7.1 (CONSTRUCTION-Inlet Connection- The inlet shank shall be not less than 48 mm In length.)	-
7-7.1-Annex A (CONSTRUCTION-Inlet Connection- External screw on inlet connections shall be such as to meet the test requirements of Annex A.)	-
7-7.2-7.2.1 (CONSTRUCTION-Seats and body)	-
7-7.2-7.2.2 (CONSTRUCTION-Seats and body-In case of detachable type of seats, colour ccding as given below shall be followed ;)	-
7-7.2-7.2.3 (CONSTRUCTION-Seats and body-The distance between the seat outlet orifice and the shutting off face of the diaphragm shall be 15 mm, Min in the fully opened position.)	-
7-7.3 (CONSTRUCTION-Diaphragm-Diaphragms made of synthetic rubber shall have the form and dimensions as required for the operation of the valve.)	-
7-7.4 (CONSTRUCTION-Back Nuts-Annex A)	-
7-7.4 (CONSTRUCTION-Back Nuts-Threads on backnuts shall also comply WIth the test requirements of Annex A.)	-
7-7.5-7.5.1 (CONSTRUCTION-Floats, Float Arm and Assembly-)	-
7-7.5-7.5.2 (CONSTRUCTION-Floats, Float Arm and Assembly-)	-
7-7.5-7.5.3 (CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Initial Deflection shall not be more than 25 mm)	-
7-7.5-7.5.3 (CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Additiononal deflection after loading for 28 days as specified in Annex B shall not be more than 12 mm)	-
7-7.5-7.5.3 (CONSTRUCTION-Floats, Float Arm and Assembly-Annex B Total deflection thus shall not he more than 37 mm)	-
7-7.6-7.6.1 (CONSTRUCTION-Discharge Arrangements)	-
7-7.6-7.6.2 (CONSTRUCTION-Discharge Arrangements)	-
7-7.6-7.6.3 (CONSTRUCTION-Discharge Arrangements)	-
8-8.1 (PERFORMANCE TEST-Hydraulic Test)	-
8-8.2 (PERFORMANCE TEST-Shut Off Test-Annex C)	-
8-8.4 (PERFORMANCE TEST-Flow Test- Annex E)	-
8-8.6 (PERFORMANCE TEST-Test for Hydraulic Pressure on Discbarge Arrangements-Annex G)	-

-
-

460

IS 15058 (2002)

PVC water - Stops at transverse contraction joints for use in masonry and concrete dams - Specification

Rs.12990.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4,4.1 Fig.1 (SHAPE AND DIMENSIONS)	-
5, 5.1 (WORKMANSHIP AND FINISH)	-
5.2 (WORKMANSHIP AND FINISH)	-
3.3 (Colour)	-
3.2 Table 1, iv) Annex A (Water absorption)	-
3.2 Table 1, iii) IS 13360 (Part 5/Sec 11) (Hardness (Shore A))	-
3.2 Table 1, i) IS 13360 (Part 5/Sec 1) (Tensile strength)	-
3.2 Table 1, ii) IS 13360 (Part 5/Sec 1) (Elongation,)	-
3.2 Table 1, v) Annex G of IS 9766 (Cold bend temperature at which samples does not crack)	-
3.2 Table 1,vi) b) Annex B (Accelerated extraction test: Elongation)	-
3.2 Table 1,vi) a) Annex B (Accelerated extraction test Tensile strength)	-
3.2 Table 1,vii) f) Annex C (Stability in effects of alkalies test Dimension change)	-
3.2 Table 1,vii) c) Annex C (Stability in effects of alkalies test Change in hardness at 7 days )	-
3.2 Table 1,vii) b) Annex C (Stability in effects of alkalies test Weight decrease at 7 day)	-
3.2 Table 1,vii) a) Annex C (Stability in effects of alkalies test Weight increase at 7 day)	-
3.2 Table 1,vii) e) Annex C (Stability in effects of alkalies test Weight decrease at 28 days)	-
3.2 Table 1,vii) d) Annex C (Stability in effects of alkalies test Weight increase at 28 days)	-

-
EXCLUDING Test facility not avaialable for Cl.3.2 (Table 1) Cold bend temperature test, Accelerated extraction Test (Tensile test & elongation);

461

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

Rs.2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 2.2.2 (Dimensions)	-

-
EXCLUDING Test facility not available for Cl. 6.4 Short Term Hydraulic Test;

462

IS 14587 (1998)

Prelaminated Medium Density Fibre Board -specification

19200 View breakup
For grade 1-Rs.19200/-, For grade II-Rs.19200/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (Dimensions and tolerances)	-
10.2, Table-1 (Test for Density)	-
10.4, Table-1 (Test for Water Absorption)	-
10.5 (test for swelling in water)	-
10.6 (test for modulis of rupture)	-
10.7 (Test for tensile strength perpendicular to Surface)	-
10.8 (Test for tensile strength perpendicular to Surface after ageing )	-
10.9 (test screw withdrawal strength)	-
10.12 (test for resistance to crack)	-
10.13 (test for resistance to cigarette burn)	-

-
-

463

IS 4351 (2003)

Steel Door Frames -

Please see remarks. View breakup
Rs.4050/- and Material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Sizes)	-
6.2 (Tolerances)	-
6.3 (Designation)	-
7, Table 2 (Profile)	-
7, Table 2 (Size, X)	-
7, Table 2 (Size, Y)	-
7, Table 2 (Rebate)	-
8.0 (CONSTRUCTION)	-
9.0 (BASE TIES)	-
10.1 (Fixing Lugs (Holdfasts))	-
10.2, Table 3 (Steel butt hinge— medium weight)	-
10.2, Table 3 (Stainless steel butt hinges medium weight)	-
10.2, Table 3 (Steel rising butt hinges)	-
10.2, Table 3 (Mild steel parliament hinges)	-
10.2, Table 3 (Mild steel light weight tee hinges)	-
10.3 (Mortar Guards)	-
10.4 (Aldrops, Sliding Bolts and Tower Bolts)	-
10.5 (Lock Strike Plate)	-
10.6 (Shock Absorbers)	-
11.1 (Pre-treatment and Phosphating)	-
11.2 (Painting)	-
11.3 (Powder Coatings)	-
5, Table 1 (Mild steel sheet (cold rolled))	-
5, Table 1 (Galvanized steel sheets — Plain grade — Lock forming (GPL), Zinc coating 120 g/m2 inchssive of both sides)	-
5, Table 1 (Stainless steel Grade — X07Crl 7 (430) X04Cr19N;; (304 S1 ))	-
5, Table 1 (Mild steel sheet (cold rolled))	-
5, Table 1 (Stainless steel Grade — X07Crl 7 (430) X04Cr19N;; (304 S1 ))	-
5, Table 1 (Galvanized steel sheets — Plain grade — Lock forming (GPL), Zinc coating 120 g/m2 inchssive of both sides)	-

-
-

464

IS 15833 (2009)

Stainless Steel Tower Bolts -specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2 (Carbon Content)	-
Clause 4.2 (Sulphur)	-
Clause 4.2 (Phosphorus)	-
Clause 4.2 (Manganese)	-
Clause 4.2 (Silicon)	-
Clause 4.2 (Chromium)	-
Clause 4.2 (nickel)	-
Cl 3 (NOMINAL SIZES)	-
Cl 4 (MATERIAL)	-
Cl 5 (MANUFACTURE)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 6 (DIMENSIONS)	-
Cl 7 (0)	-

-
sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm. Grade as per relevant IS of material may please be declared;

465

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

Rs 11950/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.0 (Types)	-
7.2 (DIMENSIONS & TOLERANCES )	-
7.2 (DIMENSIONS & TOLERANCES )	-
7.3 (DIMENSIONS & TOLERANCES )	-
8.1 (WORKMANSHIP AND FINISH )	-
8.3 (WORKMANSHIP AND FINISH )	-
10.1.1 (MOISTURE CONTENT)	-
10.1.2, 10.1.2.1 (Table-1) (GLUE ADHESION IN DRY STATE)	-
10.1.3, 10.1.3.1.1 (Table-1) (RESISTANCE TO WATER TEST)	-
10.1.3, 10.1.3.1.2 (RESISTANCE TO WATER TEST)	-
10.1.4 (RESISTANCE TO WATER TEST)	-
10.1.5 (MYCOLOGICAL TEST )	-
10.1.5, 10.1.5.1 (Table-1) (MYCOLOGICAL TEST )	-
10.1.5.2 (MYCOLOGICAL TEST )	-
10.1.6 (TENSILE STRENGTH)	-
10.1.7 (Table-2) (STATIC BENDING STRENGTH)	-
10.1.7 (Table-2) (STATIC BENDING STRENGTH)	-
10.1.8 (Table-3) (WET BENDING STRENGTH)	-
10.1.8 (Table-3) (WET BENDING STRENGTH)	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.8 (Table 3) (Cl. 10.1.8 (Table 3) (Modulus of Elasticity: Along the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Across the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Rupture: Along the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Across the Face Grain: Average))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Minimum Individual))	-
Cl. 10.1.7 (Table 2) (Cl. 10.1.7 (Table 2) (Modulus of Elasticity: Along the Face Grain: Average))	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Sum of the Tensile Strength in two directions))	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Perpendicular to grain))	-
Cl. 10.1.6 (Cl. 10.1.6 (Tensile Strength: Parallel to grain))	-
10.1.9(Chem) (RETENTION OF PRESERVATIVE)	-
4.0 (Types)	-
10.1.9 (RETENTION OF PRESERVATIVE)	-

-
-

466

IS/ISO 3183 (2012)

Petroleum and Natural Gas Industries â€” Steel Pipe for Pipeline Transportation Systems ( First Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 9.2, Table-4 (L175 Or A25, Carbon)	-
Clause 9.2, Table-4 (L175 Or A25, Sulphur)	-
Clause 9.2, Table-4 (L175 Or A25, Phosphorus)	-
Clause 9.2, Table-4 (L175 Or A25, Manganese)	-
Clause 9.2, Table-4 (L175P Or A25P, Carbon)	-
Clause 9.2, Table-5 (L830M or X120M, CE (PCM))	-
Clause 9.2, Table-5 (L830M or X120M, S)	-
Clause 9.2, Table-5 (L830M or X120M, P)	-
Clause 9.2, Table-5 (L830M or X120M, Mn)	-
Clause 9.2, Table-5 (L830M or X120M, Si)	-
Clause 9.2, Table-5 (L830M or X120M, C)	-
Clause 9.2, Table-5 (L690M or X100M, CE (PCM))	-
Clause 9.2, Table-5 (L690M or X100M, S)	-
Clause 9.2, Table-5 (L690M or X100M, P)	-
Clause 9.2, Table-5 (L690M or X100M, Mn)	-
Clause 9.2, Table-5 (L690M or X100M, Si)	-
Clause 9.2, Table-5 (L690M or X100M, C)	-
Clause 9.2, Table-5 (L625M or X90M, CE (PCM))	-
Clause 9.2, Table-5 (L625M or X90M, S)	-
Clause 9.2, Table-5 (L625M or X90M, P)	-
Clause 9.2, Table-5 (L625M or X90M, Mn)	-
Clause 9.2, Table-5 (L625M or X90M, Si)	-
Clause 9.2, Table-5 (L625M or X90M, C)	-
Clause 9.2, Table-5 (L555M or X80M, CE (PCM))	-
Clause 9.2, Table-5 (L555M or X80M, S)	-
Clause 9.2, Table-5 (L555M or X80M, P)	-
Clause 9.2, Table-5 (L555M or X80M, Mn)	-
Clause 9.2, Table-5 (L555M or X80M, Si)	-
Clause 9.2, Table-5 (L555M or X80M, C)	-
Clause 9.2, Table-5 (L485M or X70M, CE (PCM))	-
Clause 9.2, Table-5 (L485M or X70M, CE (IIW))	-
Clause 9.2, Table-5 (L485M or X70M, S)	-
Clause 9.2, Table-5 (L485M or X70M, P)	-
Clause 9.2, Table-5 (L485M or X70M, Mn)	-
Clause 9.2, Table-5 (L485M or X70M, Si)	-
Clause 9.2, Table-5 (L485M or X70M, C)	-
Clause 9.2, Table-5 (L450M or X65M, CE (PCM))	-
Clause 9.2, Table-5 (L450M or X65M, CE (IIW))	-
Clause 9.2, Table-5 (L450M or X65M, S)	-
Clause 9.2, Table-5 (L450M or X65M, P)	-
Clause 9.2, Table-5 (L450M or X65M, Mn)	-
Clause 9.2, Table-5 (L415M or X60M, Si)	-
Clause 9.2, Table-5 (L450M or X65M, C)	-
Clause 9.2, Table-5 (L415M or X60M, CE (PCM))	-
Clause 9.2, Table-5 (L415M or X60M, CE (IIW))	-
Clause 9.2, Table-5 (L415M or X60M, S)	-
Clause 9.2, Table-5 (L415M or X60M, P)	-
Clause 9.2, Table-5 (L415M or X60M, Mn)	-
Clause 9.2, Table-5 (L415M or X60M, Si)	-
Clause 9.2, Table-5 (L415M or X60M, C)	-
Clause 9.2, Table-5 (L390M or X56M, CE (PCM))	-
Clause 9.2, Table-5 (L390M or X56M, CE (IIW))	-
Clause 9.2, Table-5 (L390M or X56M, S)	-
Clause 9.2, Table-5 (L390M or X56M, P)	-
Clause 9.2, Table-5 (L390M or X56M, Mn)	-
Clause 9.2, Table-5 (L390M or X56M, Si)	-
Clause 9.2, Table-5 (L390M or X56M, C)	-
Clause 9.2, Table-4 (L210 Or A, Carbon)	-
Clause 9.2, Table-4 (L210 Or A, Sulphur)	-
Clause 9.2, Table-4 (L210 Or A, Phosphorus)	-
Clause 9.2, Table-4 (L210 Or A, Manganese)	-
Clause 9.2, Table-4 (L245 Or B, Carbon)	-
Clause 9.2, Table-4 (L245 Or B, Sulphur)	-
Clause 9.2, Table-4 (L245 Or B, Phosphorus)	-
Clause 9.2, Table-4 (L245 Or B, Manganese)	-
Clause 9.2, Table-4 (L290 Or X42, Carbon)	-
Clause 9.2, Table-4 (L290 Or X42, Sulphur)	-
Clause 9.2, Table-4 (L290 Or X42, Phosphorus)	-
Clause 9.2, Table-4 (L290 Or X42, Manganese)	-
Clause 9.2, Table-4 (L320 Or X46, Carbon)	-
Clause 9.2, Table-4 (L320 Or X46, Sulphur)	-
Clause 9.2, Table-4 (L320 Or X46, Phosphorus)	-
Clause 9.2, Table-4 (L320 Or X46, Manganese)	-
Clause 9.2, Table-4 (L360 Or X52, Carbon)	-
Clause 9.2, Table-4 (L360 Or X52, Sulphur)	-
Clause 9.2, Table-4 (L360 Or X52, Phosphorus)	-
Clause 9.2, Table-4 (L360 Or X52, Manganese)	-
Clause 9.2, Table-4 (L390 Or X56, Carbon)	-
Clause 9.2, Table-4 (L390 Or X56, Sulphur)	-
Clause 9.2, Table-4 (L390 Or X56, Phosphorus)	-
Clause 9.2, Table-4 (L390 Or X56, Manganese)	-
Clause 9.2, Table-4 (L415 Or X60, Carbon)	-
Clause 9.2, Table-4 (L415 Or X60, Sulphur)	-
Clause 9.2, Table-4 (L415 Or X60, Phosphorus)	-
Clause 9.2, Table-4 (L415 Or X60, Manganese)	-
Clause 9.2, Table-4 (L450 Or X65, Carbon)	-
Clause 9.2, Table-4 (L450 Or X65, Sulphur)	-
Clause 9.2, Table-4 (L450 Or X65, Phosphorus)	-
Clause 9.2, Table-4 (L450 Or X65, Manganese)	-
Clause 9.2, Table-4 (L485 Or X70, Carbon)	-
Clause 9.2, Table-4 (L485 Or X70, Sulphur)	-
Clause 9.2, Table-4 (L485 Or X70, Phosphorus)	-
Clause 9.2, Table-4 (L485 Or X70, Manganese)	-
Clause 9.2, Table-4 (L175 Or A25, Carbon)	-
Clause 9.2, Table-4 (L175 Or A25, Sulphur)	-
Clause 9.2, Table-4 (L175 Or A25, Phosphorus)	-
Clause 9.2, Table-4 (L175 Or A25, Manganese)	-
Clause 9.2, Table-4 (L175P Or A25P, Carbon)	-
Clause 9.2, Table-4 (L175P Or A25P, Sulphur)	-
Clause 9.2, Table-4 (L175P Or A25P, Phosphorus)	-
Clause 9.2, Table-4 (L210 Or A, Manganese)	-

-
sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm. Steel Grade may please be declared; EXCLUDING -; hydraulic test,DWT test,some defect test

467

IS 4432 (1988)

Specification for case hardening steels (First Revision)

Please see remarks. View breakup
the testing charges for the product are Rs 11660/- excluding Grain size, Cleanliness of steel and additional tests For elements other than Table-1: Rs 1004/- per element

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
TABLE-1 (Clause-5) ( CARBON)	-
TABLE-1 (Clause-5) (SILICON)	-
TABLE-1 (Clause-5) (MANGANESE)	-
TABLE-1 (Clause-5) (Nickel)	-
TABLE-1 (Clause-5) (Chromium)	-
TABLE-1 (Clause-5) (Molybdenum)	-
TABLE-1 (Clause-5) (SULPHUR)	-
TABLE-1 (Clause-5) (PHOSPHURS)	-
TABLE-1 (Clause-5) (TITANIUM)	-
TABLE-1 (Clause-5) (VANADIUM)	-
TABLE-1 (Clause-5) (NIOBIUM)	-
TABLE-1 (Clause-5) ( ALUMINIUM)	-
TABLE-1 (Clause-5) (NITROGEN)	-
4 (Freedom from Defects)	-
7 (Hardness)	-
11 (Dimensional Tolerances)	-

-
sample Size 5 pcs of 5x5 cm having dia> 3mm and thickness > 0.8 mm. Steel Grade/designation may please be declared; EXCLUDING -; heat treatment

468

IS 15644 (2006)

Safety of electric toys

7050.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.0 (Marking and instructions)	-
8.0 (Power Input)	-
9.0 (Heating and abnormal operation)	-
10.0 (Electrical strength at operating temperature)	-
11.1 (Moisture resistance)	-
11.2 (Resistant to humidity)	-
12.0 (Electric strength at room temperature)	-
13.0 (Mechanical strength)	-
14.1 (Construction)	-
14.2 (Construction)	-
14.3 (Construction)	-
14.4 (Construction)	-
14.5 (Construction)	-
14.6 (Construction)	-
14.7 (Construction)	-
14.8 (Construction)	-
14.9 (Construction)	-
14.1 (Construction)	-
14.11 (Construction)	-
14.12 (Construction)	-
14.13 (Construction)	-
14.14 (Construction)	-
15.1 (Protection of cords and wires)	-
15.2 (Protection of cords and wires)	-
16.0 (Components)	-
17 Table-1 (Screws and connections)	-
17 Table-1 (Nominal daimeter of screws made of insulating material)	-
18.0 (Clearance and creepage distance)	-
18.0 (Clearance and creepage distance)	-
18.0 (Clearance and creepage distance)	-
19.1 (Ball pressure test IEC 60695-10-2)	-
19.2.1 (Glow wire test IEC 60695-2-11)	-
19.2.2 (Needle flame test)	-
9873 (Part-1) 4.2-5.24.2 (Reasonably foreseeable abuse -Drop Test)	-
9873 (Part-1) 4.2-5.24.5 (Reasonably foreseeable abuse -Torque test)	-
9873 (Part-1) 4.2-5.24.7 (Reasonably foreseeable abuse -Compression test)	-
9873 (Part-1) 4.4.1-5.2 (Small parts-For children under 36 months)	-
20.0 (Radiation, toxicity and similar hazards)	-
9873 (Part-3) 4.1 - Table 1 (Selenium (Se) - Cl 7,8,9 )	-
9873 (Part-4) 4.11.2 (Edges, points, and small parts)	-
7.1.2 (Marking and instructions )	-
7.2 (Marking and instructions )	-
7.3 (Marking and instructions )	-
7.4 (Marking and instructions )	-
7.5 (Marking and instructions )	-
7.6 (Marking and instructions )	-
9.3 (Heating and abnormal operation)	-
9.4 (Heating and abnormal operation)	-
9.5 (Heating and abnormal operation)	-
9.6 (Heating and abnormal operation)	-
9.7 (Heating and abnormal operation)	-
9.8 (Heating and abnormal operation)	-
5.15 (General Conditions)	-
5.15 (General Conditions)	-
5.15 (General Conditions)	-
5.15 (General Conditions)	-
5.15 (General Conditions)	-
7.1 (Marking and instructions )	-
7.1.1 (Marking and instructions )	-
13.0 ((Mechanical strength))	-
14.15 (Construction)	-
9873 (Part-3) 4.1 - Table 1 (Mercury (Hg) - Cl 7,8,9 )	-
9873 (Part-3) 4.1 - Table 1 (Lead (Pb) - Cl 7,8,9 )	-
9873 (Part-3) 4.1 - Table 1 (Chromium (Cr) - Cl 7,8,9 )	-
4.1 - Table 1 of (IS 9873-3-2017) (Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 of (IS 9873-3-2017) (Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 of (IS 9873-3-2017) (Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
4.1 - Table 1 of (IS 9873-3-2017) (Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-
9873 (Part-9) 3 (Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-

-
3 piece

469

IS 2074 (2023)

Ready Mixed Paint Air Drying Red Oxide Zinc Chrome Priming -Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5.1 (a) (Pigment)	-
Cl-5.1.1 (a) ("Zinc oxide content Chromic anhydride content")	-
Cl-5.1.1 (b) (Synthetic red oxides of iron or Natural red oxides of iron or A mixture of both which shall correspond to red oxide, percent by mass)	-
Cl-5.3 (Compatibility with Thinner)	-
Cl-5.4 (Freedom from Objectionable Impurities)	-
Cl-5.5 (Lead Restriction)	-
Cl-5.6 & 8 Table-1 (i) (a) (Consistency)	-
Cl-5.6 & 8, Table-1 (i) (b) (Viscosity by ford cup No. 4 at 27±2°C)	-
Cl-5.6 & 8, Table-1 (ii) (Mass, in kg/10 1, Min)	-
Cl-5.6 & 8, Table-1 (iii) ("Drying time, h, Max a) Surface dry b) Hard dry")	-
Cl-5.6 & 8, Table-1 (iv) (a) Finish)	-
Cl-5.6 & 8, Table-1 (iv) (b) Gloss 60° , Max)	-
Cl-5.6 & 8, Table-1 (v) (Fineness of grind, microns, Max)	-
Cl-5.6 & 8, Table-1 (vi) (Colour)	-
Cl-5.6 & 8,, Table-1 (vii) a) (Flexibility and adhesion: Bend test with 6.25mm dia mandrel and in type 1 apparatus)	-
Cl-5.6 & 8,, Table-1 (vii) b) (Flexibility and adhesion: Scratch hardness)	-
Cl-5.6 & 8, Table-1 (viii) (Flash point)	-
Cl-5.6 & 8,, Table-1 (x) (a) (Resistance to humidity)	-
Cl-5.6 & 8, Table-1 (xi) (Accelerated storage stability test)	-
Cl-5.6 & 8, Table-1 (xii) ("Keeping properties Visual observation (Corrosion and odour of putrefaction, rancidity or souring) ")	-
Cl-5.6 & 8, Table-1 (x) (c) (Resistance to salt spray)	-
Cl-5.6 & 8,, Table-1 (ix) (Volume solids, percent)	-
Cl-5.6 & 8, Table-1 (xii) ("Keeping properties Change in skinning")	-
Cl-5.6 & 8, Table-1 (xii) ("Keeping properties Degree of settling ")	-
Cl-5.6 & 8, Table-1 (xii) ("Keeping properties Observation of dried film ")	-
Cl-5.6 & 8, Table-1 (xii) ("Keeping properties Loss of mass resulting from Storage ")	-

-
Test facility is not available for mentioned exclusions parameters; EXCLUDING Volume solids;

470

IS 14625 (2015)

Plastics Feeding Bottles ( First Revision )

Rs 16930 (Excluding tests for material as per Cl.4.1 an View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Physical Requirements)	-
Cl 5.1.3 (Wall Thickness)	-
Cl 5.1.4 (Capacity)	-
Cl 5.3.2 (Transparecy)	-
Cl 5.3.3 (Leakage Test)	-
Cl 5.3.4 (Drop Test)	-
Cl 5.3.5 (Ageing Resistance)	-
Cl 5.3.6 (Compressive Deformation Resistance)	-
Cl 5.3.7 (Product Resistance of Printed Containers)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Antimony)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Arsenic)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Antimony)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Arsenic)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Chromium)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Cadmium)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Lead)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Barium)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Selenium)	-
Cl 5.1.4.2 (a) (Test for permanency of Pigment)	-
5.3.8 a) (Migration Test a) Distilled water at 40±2° hrs)	-
5.3.8 b) (Migration Test b) n-Haptane at 38±1° C for 30 min)	-
4.1 (Material Identification, Bisphenol A,)	-
Cl.5.2.1.7, Table-1(iii) (Migration of certain elements, Reqiurement as per table 1, Mercury)	-
Cl.5.3.9.2, Table-3(i) (Specific migration , Barium)	-
Cl.5.3.9.2, Table-3(ii) (Specific migration , Cobalt)	-
Cl.5.3.9.2, Table-3(iii) (Specific migration , Copper)	-
Cl.5.3.9.2, Table-3(iv) (Specific migration , Iron)	-
Cl.5.3.9.2, Table-3(v) (Specific migration , Lithium)	-
Cl.5.3.9.2, Table-3(vi) (Specific migration , Manganese)	-
Cl.5.3.9.2, Table-3(vii) (Specific migration , Zinc)	-
Cl.5.3.9.2, Table-3(viii) (Specific migration , Antimony)	-
Clauses 5.3.9.2 and 5.3.9.3,Table 3, S.no.(ix) (Phthalic acid, bis(2-ethylhexyl)ester (DEHP)-ISO 18856)	-

-
60 ml (100 Nos), Above 60 ml (60 Nos), complete facility

471

IS 44 (1991)

Iron oxide pigments for paints - Specification (Second Revision)

- View breakup
Rs Grade1=8554/- Grade2=9804/- Grade3=7304/- Grade4=8254/- Grade5=7604/- Grade6=8204/- Grade7=8840/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (Composition Grade 1)	-
5.1.2 (Composition Grade 2)	-
5.1.3 (Composition Grade 3)	-
5.1.4 (Composition Grade 4)	-
5.1.5.1 (Composition Grade 5 & Grade 6 Type C)	-
5.1.5.2 (Composition Grade 5 & Grade 6 Type D)	-
5.1.6 (Composition Grade 7)	-
5.2 (Form & Condition)	-
5.3 Table-1 i. (Volatile matter - 7 of IS 33)	-
5.3 Table-1 ii. (Residue on sieve - 8 of IS 33)	-
5.3 Table-1 iii. (Oil absorption - 9 of IS 33)	-
5.3 Table-1 iv (a) (Colour staining power)	-
5.3 Table-1 iv (b) (Colour undertone)	-
5.3 Table-1 v. (Matter insoluble in water - 17 of IS 33)	-
5.3 Table-1 vi. (Sum of water soluble Chloride - Annex-A)	-
5.3 Table-1 vi. (Sum of water soluble Sulphate - Annex-A)	-
5.3 Table-1 vii. (Acidity or Alkalinity - 18 of IS 33)	-
5.3 Table-1 viii. (pH of aqueous extract)	-
5.3 Table-1 ix. (Total Iron - Annex-B)	-
5.3 Table-1 x. (Ferrous Iron - Annex-C)	-
5.3 Table-1 xi. (Carbonates - Annex-D)	-
5.3 Table-1 xii. (Calcium compounds - Annex-E)	-
5.3 Table-1 xiii. (Manganese Content - Annex-F)	-
5.3 Table-1 xiv. (Loss on ignition - Annex-G)	-
5.4 (Lead Free Material - 25 of IS 33)	-
5.3 Table-1 xiv. (Loss on ignition - Annex-G)	-

-
Test facility is not availalble for acidity and alkalinity and matter soluble in water test. approved sample and declaration is required for colour, oil absorption test, residue on sieve test.; EXCLUDING Residue on sieve, oil absorption. Colour- staining power and undertone, acidity and alkalinity, Matter soluble in water;

472

IS 1664 (2002)

Mineral mixtures for supplementing cattle feeds - Specification (Fourth Revision)

Rs11600- Type 1 ; Rs 11600/- for type 2 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
(Cl. 5) (Description )	-
(Cl. 6.1) (Seiving through 212 micron IS Sieve),)	-
table 1, (Cl. 6.3) (Moisture)	-
(Cl. 5) (Description )	-
table 1, (Cl. 6.3) (Presence of protenious/organic impurities)	-
table 1, (Cl. 6.3) (Total ash in moisture free sample)	-
table 1, (Cl. 6.3) (Arsenic(as As2O3),.)	-
table 1, (Cl. 6.3) (Lead(as Pb), .)	-
table 1, (Cl. 6.3) (Acid insoluble ash (on dry basis))	-
table 1, (Cl. 6.3) (Sulphur (on dry basis))	-
table 1, (Cl. 6.3) (Zinc (on dry basis))	-
table 1, (Cl. 6.3) (Cobalt (on dry basis))	-
table 1, (Cl. 6.3) (Mangnanese (on dry basis))	-
table 1, (Cl. 6.3) (Copper (on dry basis))	-
table 1, (Cl. 6.3) (Iodine (as KI ) on dry basis,)	-
table 1, (Cl. 6.3) (Iron (on dry basis))	-
table 1, (Cl. 6.3) (Magnesium( on dry basis))	-

-
500 gm x 3 EXCLUDING "Iron,Iodine,Copper,Manganese,Cobalt,Zinc, Sulphur B. anthracis, Clostridium; "

473

IS 9973 (1981)

Specification for visor for scooter helmets

Rs.6900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Impact resistance)	-
5.2 (Penetration resistance)	-
5.3 (Flammability)	-
5.4.2 (Spherical&Cylindral error)	-
5.5 (Field of Vision)	-
7.0 (Mass)	-
5.4.1 (Distortion)	-

-
-

474

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

16,189 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Normal use)	-
4.2 (Reasonably foreseeable abuse)	-
4.3.1 (Material quality)	-
4.3.2 (Expanding materials)	-
4.4.1 (For children under 36 months)	-
4.4.2 (For children 36 months and over but under 72 months)	-
4.5.1.2 (Squeeze toys, rattles, and certain other toys and components of toys)	-
4.5.1.3 (Other toys or components of toys with nearly spherical, hemispherical, circular flared, or dome-shaped ends of toys having a mass less than 0,5 kg and intended for children under 18 months)	-
4.5.1.4 (Toy fasteners (e.g. nails, bolts, screws, and pegs) with nearly spherical, hemispherical, or dome-shaped ends intended for children 18 months and over but under 48 months)	-
4.5.2 (Small balls)	-
4.5.3 (Pompoms)	-
4.5.4 (Pre-school playfigures)	-
4.5.5 (Toy pacifiers)	-
4.5.6 (Balloons)	-
4.5.7 (Marbles)	-
4.5.8 (Hemisphericshaped toys)	-
4.6.1 (Accessible sharp edges of glass or metal)	-
4.7.2 (Functional sharp points)	-
4.7.3 (Wooden toys)	-
4.8 (Projections)	-
4.9 (Metal wires and rods)	-
4.6.3 (Edges on metal toys)	-
4.6.4 (Edges on moulded toys)	-
4.10 (Plastic film or plastic bags in packaging and in toys)	-
4.11.1 (General)	-
4.11.2 (Cords in toys intended for children under 18 months)	-
4.11.3 (Cords in toys intended for children 18 months and over but under 36 months)	-
4.11.4 (Fixed loops and nooses intended for children under 36 months)	-
4.11.5 (Cords on pull toys)	-
4.11.11 (Cords, strings and lines for flying toys)	-
4.11.6 (Electrical cables)	-
4.11.7 (Diameter of certain cords intended for children under 36 months)	-
4.11.8 (Self-retracting cords intended for children under 36 months)	-
4.11.9 (Toys attached to or intended to be strung across, or otherwise attached to, a cradle, cot, perambulator or carriage)	-
4.11.10 (Cords on toy bags)	-
4.11.11 (Cords, strings and lines for flying toys)	-
4.12.1 (Toy pushchairs, perambulators and similar toys)	-
4.12.2 (Other toys with folding mechanisms)	-
4.12.3 (Hinge-line clearance)	-
4.13.1 (Circular holes in rigid materials)	-
4.13.2 (Accessible clearances for movable ,segments)	-
4.13.3 (Chains or belts in ride-on toys)	-
4.13.4 (Other driving mechanisms)	-
4.13.5 (Winding keys)	-
4.14 (Springs)	-
4.15.1.1 (Sideways stability, feet available for stabilization)	-
4.15.1.2 (Sideways stability, feet unavailable for stabilization)	-
4.15.1.3 (Fore and aft stability)	-
4.15.2 (Overload requirements for ride-on toys and seats)	-
4.15.3 (Stability of stationary floor toys)	-
4.16.1 (Ventilation)	-
4.16.2.1 (Lids, doors and similar devices)	-
4.16.2.2 (Lid support for toy chests and similar toys)	-
4.16.3 (Toys that enclose the head)	-
4.17 (Simulated protective equipment, such as helmets, hats and goggles)	-
4.18.2 (Projectiles)	-
4.18.4 (Projectile toys without stored energy)	-
4.19 (Rotors and propellers)	-
4.20 (Aquatic toys)	-
4.21 (Braking)	-
4.22.1 (Instructions for use)	-
4.22.2 (Determination of maximum saddle height)	-
4.22.3 (Braking requirements)	-
4.23 (Speed limitation of electrically driven ride-on toys)	-
4.24 (Toys containing a heat source)	-
4.25 (Liquid -filled toys)	-
4.26 (Mouth - actuated toys)	-
4.27 (Toy roller skates, toy inline skates and toy skateboards)	-
4.28 (Percussion caps specifically designed for use in toys)	-
4.30.2 (Warnings and instructions for use)	-
4.30.3 (Strength)	-
4.30.4 (Stability)	-
4.30.5 (Adjustable and folding steering tubes and handlebars)	-
4.30.6 (Braking)	-
4.30.7 (Wheel size)	-
4.30.8 (Projections)	-
4.31.1 (Magnetic/electrical experimental sets intended for children 8 years and over)	-
4.31.2 (All other toys with magnets and magnetic components)	-
4.32 (Yo-yo balls)	-
4.33 (Straps intended to be worn fully or partially around the neck)	-
4.34 (Sledges and toboggans with cords for pulling)	-
4.35 (Jaw entrapment in handles and steering wheels)	-
4.1 (Normal use)	-
4.2 (Reasonably foreseeable abuse- Cl. 5.24.2 Drop test)	-
4.2 (Reasonably foreseeable abuse- Cl. 5.24.3 Tip-over test for large and bulky toys)	-
4.2 (Reasonably foreseeable abuse- Cl. 5.24.4 Dynamic strength test for wheeled ride-on toys other than toy scooters)	-
4.2 (Reasonably foreseeable abuse- Cl. 5.24.5 Torque test)	-
4.2 (Reasonably foreseeable abuse- Cl. 5.24.6.1- Tension test- General)	-
4.2 ("Reasonably foreseeable abuse- Cl. 5.24.6.2- Tension test- Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys ")	-
4.2 (Reasonably foreseeable abuse- Cl. 5.24.6.3- Tension test- Tension test for pompoms)	-
4.2 (Reasonably foreseeable abuse- Cl. 5.24.6.4- Tension test- Tension test for protective components)	-
4.1 (Normal use)	-
4.2 (Reasonably foreseeable abuse)	-
4.2 (Reasonably foreseeable abuse- Cl. 5.24.6.1- Tension test- General)	-
9873 (Part - 3) 4.1 - Table 1 (Selenium (Se) - Cl 7,8,9 )	-
9873 (Part - 3) 4.1 - Table 1 (Mercury (Hg) - Cl 7,8,9 )	-
9873 (Part - 3) 4.1 - Table 1 (Lead (Pb) - Cl 7,8,9 )	-
9873 (Part - 3) 4.1 - Table 1 (Chromium (Cr) - Cl 7,8,9 )	-
9873 (Part - 3) 4.1 - Table 1 (Cadmium (Cd) - Cl 7,8,9)	-
9873 (Part - 3) 4.1 - Table 1 (Barium (Ba) - Cl 7,8,9 )	-
9873 (Part - 3) 4.1 - Table 1 (Arsenic (As) - Cl 7,8,9 )	-
9873 (Part - 3) 4.1 - Table 1 (Antimony (Sb) - Cl 7,8,9)	-
9873 (Part - 9) 3 (Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-
9873 (Part - 9) 3 (Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-

-
EXCLUDING -; i) Acoustic test

475

IS 4151 (2015)

Protective helmets for motorcycle riders - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Shell)	-
4.5 (Metal Parts)	-
4.6 (Visor)	-
6.1 (General)	-
6.2 (Shell)	-
6.3 (Protactive Padding)	-
6.4 (Retention System)	-
6.7 (Peripheral Vision)	-
6.8 (Workmanship and Finish)	-
7.2 (Impact Absorption Test)	-
7.3 (Rigidity Test)	-
7.4 (Projections and Surface Friction Test)	-
7.5 (Dynamic Test of Retention System)	-
7.6 (Audibility Test)	-
7.7 (Retention Test of Helmet)	-
7.8 (Micro-Slip Test of the Chin Strap)	-
7.9 (Test for Resistance to Abrasion of the Chin Strap )	-
7.10.1 (Inadvertent Release by Pressure)	-
7.10.2 (Ease of Release)	-
7.10.3 (Durability of Quick Release Mechanism)	-

-
Quanity required for Complete Testing: 15 nos. of Helmets, Additional 3 Meters Chin strap and 2 nos. of Additional Buckle

476

IS 10908 (1991)

Flexible rubber tubing for liquefied petroleum gas - Specification (First Revision)

7800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.1 (The tubing made out of this material shall be green in colour )	-
Cl.4.2 (The walls shall be seamless and free from all visible such as lumps, blows-holes,cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas)	-
Cl4.3.1 (The tubing shall be supplied in 6.4 and 7.0 mm inisde diametre,The tolerance on nominal diamtere shall be as per table 1)	-
Cl4.3.2 (it shall comply with the thickness as givien in table 1 when measured according to 4.2.2 of IS 443;1975 The readings shall be taken from different sample sections.)	-
Cl.4.4,(Cl.4.4.1) (when tested in accordance with the method given in AnnexureA. It shall fit over the standard and oversize metal nozzle shown in Fig1,2 and 3)	-
Cl.4.4,(Cl.4.4.2) (it shall remain atatched to both nozzles throught the test period)	-
Cl.4.5 (When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the increase in the outside diametre of the tubing ,Also the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-
Cl.4.6 (Shore Hardness: the hardnesss on the flatsurface of the cut/slit tubing shall be measured and the same shall be 60 ± 5˚A)	-
Cl.4.7 (Accelerated Ageing test, the flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100Deg Cfor 72 hours in accordance with the method prescribed in IS 3400 (Part 4) it shall not show a change of + 10 A of its orignal shore hardness )	-
Cl.4.8.1 (Flexible test , Annexure B The gas pressure shown on the manometre shall not drop by more than 1 Kpa)	-
Cl4.8.2 (The tubing shall be so flexible that it will make contact with a cylinder former of radius 68 mm for at least 110 deg of its circumference when the tubing is placed over the framer and a mass of 1.6 kg is attcahed to each end)	-
Cl.4.9 (Crushing test , )	-
Cl.4.10 (Resistance to lpg ,Annexure c Shall not be more than 15 % of the initial mass of the tubing and the amount of exctractable matter shall not excced 10 percent of the iniital mass of te tubing)	-
Cl.4.12 (Burning behaviour on exposure to small flame,Annexure E tubing shall not burn to either of the outer marks within the test period of 45 seconds)	-

-
EXCLUDING -; Test facility not avalible For ozone test

477

IS 9573 : Part 2 (2017)

Rubber hose for liquefied petroleum gas (Lpg) - Specification: Part 2 domestic and commercial application (Fourth Revision)

Rs. 7695/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2.1 (Lining)	-
Clause 4.2.2 (a) (Reinforcement)	-
Clause 4.2.2 (b) (Reinforcement)	-
Clause 4.2.3 (Cover)	-
Clause 4.3 Sub Clause 4.3.1 Table 1 (Bore Size)	-
Clause 4.3 Sub Clause 4.3.2 (a) (Thickness of Lining and Cover)	-
Clause 4.3 Sub Clause 4.3.2 (b) (Thickness of Lining and Cover)	-
Clause 4.3 Sub Clause 4.3.3 (Length)	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (a) (Tensile Strength- Lining)	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (i) (b) (Tensile Strength- cover)	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (a) (Elongation at break- Lining)	-
Clause 4.4 Sub Clause 4.4.1 Table 2 (ii) (b) (Elongation at break- Cover)	-
Clause 4.4 Sub Clause 4.4.2 (a) (Accelerated Ageing Test lining)	-
Clause 4.4 Sub Clause 4.4.2 (b) (Accelerated Ageing Test lining)	-
Clause 4.4 Sub Clause 4.4.2 (a) (Accelerated Ageing Test cover)	-
Clause 4.4 Sub Clause 4.4.2 (b) (Accelerated Ageing Test cover)	-
Clause 4.4 Sub Clause 4.4.3 (a) (Resistance of Lining to n-pentane)	-
Clause 4.4 Sub Clause 4.4.3 (b) (Resistance of Lining to n-pentane)	-
Clause 4.5 Sub clause 4.5.2 (Low Temperature Flexibility)	-
Clause 4.5 Sub clause 4.5.3 (Flexibility of Hose)	-
Clause 4.5 Sub clause 4.5.5 4.5.5.1 (Proof pressure test)	-
Clause 4.5 Sub clause 4.5.5 4.5.5.2 (Bursting pressure)	-
Clause 4.5 Sub clause 4.5.6 (Grip Strength Test)	-
Clause 4.5 Sub clause 4.5.7 (Burning Behaviour)	-

-
EXCLUDING -; Test facility not avalible For ozone test

478

IS 2835 (1987)

Specification for flat transparent sheet glass (Third Revision)

Rs 525/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (CLASSIFICATION)	-
4.1.1 (Material)	-
4.2-Table 1 & Cl 5.1 (Thickness )	-
4.2-Table 1 (Length )	-
4.2-Table 1 (Width)	-
4.3-Table 2-i (Gaseous inclusion)	-
4.3-Table 2-ii (Opaque gaseous inclusion)	-
4.3-Table 2-iii (Knots, dirts and stones)	-
4.3-Table 2-iv & Cl 5.2 (Scratches, rubs and crush)	-
4.3-Table 2-v & Cl 5.3 (Bow)	-
4.3-Table 2-vi & Cl 5.4 (Reams, Light Strings and lines)	-
4.1 (Material)	-
4.3-Table 2-vii (Waviness)	-
4.3-Table 2-viii (Sulphur stains)	-
4.3-Table 2-ix (Corner breakage and chip)	-
4.3.1-Table 2A-i (Allowable Cluster of Defects for AA Quality at Central area)	-
4.3.1-Table 2A-i (Allowable Cluster of Defects for AA Quality at Outer area)	-
4.3.1-Table 2A-ii (Allowable Cluster of Defects for A Quality at Central area)	-
4.3.1-Table 2A-ii (Allowable Cluster of Defects for A Quality at Outer area)	-
4.3.1-Table 2A-iii (Allowable Cluster of Defects for B Quality at Central area)	-
4.3.1-Table 2A-iii (Allowable Cluster of Defects for B Quality at Outer area)	-

-
-

479

IS 7079 (2008)

Automotive vehicles - Brake hose assemblies forhydraulicbraking systems used with non - Petroleum base brake fluid specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.9 (Tensile Test-Separation rate 25 ± 3 mm/min(This test need not be carried out if it has been carried out as part of test described in 5.10.))	-
5.9 (Tensile Test-Separation rate 50 ± 3 mm/min.(This test need not be carried out if it has been carried out as part of test described in 5.10.))	-
4.2.1 (Construction-Lining)	-
4.2.2 (Construction-Reinforcement and Reinforcement Plies)	-
4.2.3 (Construction-Cover)	-
5.3 (Visual Test)	-
5.6 (Pressure Test-Prior to dispatch each complete hose assembly shall be subjected to a pressure test using inert gas, air, water or brake fluid conforming to IS 8654 as the pressure medium. The test pressure shall be between 10.3 Mpa and 14.5 Mpa for inert gas and air, and between 20.7 Mpa and 24.8 Mpa for water and brake fluid.)	-
5.7, Table 4 (Bursting Strength Test-(Annex C).)	-

-
EXCLUDING -; Only Dimension test Avalible

480

IS 5983 (1980)

Specification for eye - Protectors (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4/4.2 (DESIGN AND MANUFACTURE-Head-band)	-
3/3.1/3.1.1 (TYPES AND DESIGNATION-Types- Eye-Protector)	-
3/3.1/3.1.2 (TYPES AND DESIGNATION-Types- Oculars)	-
4/4.0 (DESIGN AND MANUFACTURE-General)	-
4/4.1 (DESIGN AND MANUFACTUREComfort to the Wearer)	-
4/4.3 (DESIGN AND MANUFACTURE-Fittings)	-
4/4.4 (DESIGN AND MANUFACTURE-Ventilation)	-
4/4.6 (DESIGN AND MANUFACTURE-Composition of Oculars (see 3.1.2))	-
5/5.1/5.1.1/5.1.1.1-Fig1 (REQUIREMENTS-General Requirements- Oculars-Dimensions)	-
5/5.1/5.1.1/5.1.1.4 (REQUIREMENTS-General Requirements- Oculars-Colour recognition)	-

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List