BIS - LIMS (Laboratory Information Management System)

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List

Reset

897 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

691

IS 15911 (2010)

Structural steel (Ordinary Quality) - Specification

Rs 6750/- For elements other than Table-1: Rs 1004/- pe View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Freedom from defects)	-
5 and 10.3.1 (Tensile strength. IS 1608)	-
5 and 10.3.1 (Yield Stress. IS 1608)	-
5 and 10.3.1 (Percentage Elongation. . IS 1608)	-
11.3 ( Bend Test. IS 1599)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (Mass. IS 808)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (D)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (B)	-
Cl 12 of IS 15911 and Table 2.1 of IS 808 (T)	-
Table-1, 5.1, 8.1 & 8.2 (Carbon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Sulphur: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Nitrogen: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Chromium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Molybdenum: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Vanadium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Nickel: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Copper: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Aluminium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Niobium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Titanium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Boron: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Chromium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Molybdenum: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Vanadium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Nickel: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Copper: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Titanium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Niobium: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Boron: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Silicon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

692

IS 14184 (1994)

Pesticide - Cartap hydrochloride G - Specification

Rs.2900.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Particle Size)	-
3.2.3 (Dust)	-
3.2.4 (Moisture Content)	-
3.3.2 (pH or 1 percent ( mlm ) extract)	-

-
-

693

IS 1155 (1968)

Specification for wheat aita (Second Revision)

Rs. 900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
CL 3.1 (Decription)	-
Table 1 (i), Annex A (Moisture LG)	-
Table 1 (i), Annex A (Moisture HG)	-
Table 1 (ii), Annex B (Total Ash (on dry basis) LG)	-
Table 1 (ii), Annex B (Total Ash (on dry basis) HG)	-
Table 1 (iii), Annex C (Add insoluble Ash (on dry basis) LG)	-
Table 1 (iii), Annex C (Add insoluble Ash (on dry basis) HG)	-
Table 1 (iv), Annex D (Glutin (on dry basis) LG)	-
Table 1 (iv), Annex D (Glutin (on dry basis) HG)	-
Table 1 (v), Annex E (Crude Fibre (on dry basis) LG)	-
Table 1 (v), Annex E (Crude Fibre (on dry basis) HG)	-
Table 1 (vi), Annex F (Alcoholic acidity (As H2SO4.), with 90 prcent Alcohol (on dry basis) LG)	-
Table 1 (vi), Annex F (Alcoholic acidity (As H2SO4.), with 90 prcent Alcohol (on dry basis) HG)	-
Table 1 (vii), Annex G (Granularity(on dry basis) LG)	-
Table 1 (vii), Annex G (Granularity(on dry basis) HG)	-

-
excluding 1- Uric acid, 2-Granularity, 3-Microscopic Appearance;

694

IS 14300 (1995)

Neem based EC containing azadirachtin - Specification

Rs. 1552/- (excluding Azadirachtin content and Aflatox View breakup
Rs. 1552/- (excluding Azadirachtin content and Aflatoxin content).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 3.2.1 (Description)	-
Cl. 3.2.2 (Cold Test)	-
Cl. 3.2.3 (Flash point)	-
Cl. 3.2.4 (Emulsion Stability)	-
Cl. 3.2.1 (Description)	-

-
excluding Cl. 3.3.1 & Cl. 3.3.3 Azadirachtin Content, Aflatoxin content;

695

IS 7312 (2018)

Welded and seamless steel dissolved acetylene gas cylinders - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 4.1, IS 6240-2008 , Cl 6.2 (Carbon Content)	-
Cl. 4.1, IS 6240-2008 , Cl 6.2 (Sulphur Content)	-
Cl. 4.1, IS 6240-2008 , Cl 6.2 (Phosphorous Content)	-
Cl. 4.1, IS 6240-2008 , Cl 6.2 (Manganese Content)	-
Cl. 4.1, IS 6240-2008 , Cl 6.2 (Aluminium Content)	-
Cl. 4.1, IS 6240-2008 , Cl 6.2 (Silicon Content)	-
Cl. 4.1, For Seamless - IS 7285 (P-1)-2018, Cl 5.2 , Table-1 & 2 (Carbon Content)	-
Cl. 4.1, For Seamless - IS 7285 (P-1)-2018, Cl 5.2 , Table-1 & 2 (Combined Value Of Micro-Alloying Elements like V, Nb, Ti, B, Zr, Sn)	-
Cl. 4.1, For Seamless - IS 7285 (P-2)-2017, Cl 5.2 , Table-1, 2 (Carbon Content)	-
Cl. 4.1, For Seamless - IS 7285 (P-2)-2017, Cl 5.2 , Table-1, 2 (Sulphur + Phosphorous Content)	-
Cl. 4.3 , For Footing Material, Grade HR1 (Desig Commertial) Of IS 1079-2017, Cl. 7.2, Table 3 & 4 (Carbon Content)	-
Cl. 4.3 , For Footing Material, Grade HR1 (Desig Commertial) Of IS 1079-2017, Cl. 7.2, Table 3 & 4 (if addition of Micro Alloying Elements like B, TI, Nb,& V either single of Combination)	-
Cl. 4.2 , For Bung / Valve, as per IS 2062-2011, Grade / Desig - E-250, Quality - A (Carbon Content)	-
Cl. 4.2 , For Bung / Valve, as per IS 2062-2011, Grade / Desig - E-250, Quality - A (Sulphur Content)	-
Cl. 4.2 , For Bung / Valve, as per IS 2062-2011, Grade / Desig - E-250, Quality - A (Phosphorus Content)	-
Cl. 4.2 , For Bung / Valve, as per IS 2062-2011, Grade / Desig - E-250, Quality - A (Manganese Content)	-
Cl 4.2 , Class 1A Desig 15C8 of IS 1875-1992, Cl 6.1 & 6.2 For section 250 mm2 or Less (Carbon Content, IS 228)	-
Cl 4.2 , Class 2 Desig 20C8 of IS 1875-1992, Cl 6.1 & 6.2 for section 250 mm2 or less (Carbon Content, IS 228)	-
9,9.1 (VALVES AND VALVES PAD)	-
9.2 (Valve Protection The valve shall be protected by a stout metal cap perforated for ventilation and of thickness not less than 3.5 mm, screwed on to the neck, or in any other manner approved by the statutory authority.)	-
9.3 (Valves)	-
10,10.1 (FITTINGS OTHER THAN VALVES Footring)	-
10,10.1 (FITTINGS OTHER THAN VALVES Footring )	-
10,10.1 (FITTINGS OTHER THAN VALVES Footring)	-
10,10.1 (FITTINGS OTHER THAN VALVES Footring The bottom of the foot ring shall not be less than 8 mm below the outside bottom of the cylinder shell for cylinders up to 34 l nominal water capacity. For cylinders of more than 34 l itresnominal water capacity and up to 50 litres nominal water capacity, this value shall be minimum 15 mm and for cylinders exceeding 50 Iiters nominal water capacity, this value shall be minimum 25 mm)	-
10.2,10.2.1 IS 13497 (Safety Device)	-
10.2.2 (Safety Device)	-
14 (CHECKING OF WATER CAPACITY The water capacity of the cylinders shall be checked. This shall be done by weighing or by volumetric method. Water capacity of the cylinder shall have atolerance of + 3/-0 percent on the declared value. )	-
15.1 IS 3196(Part 3) (Hydrostatic Stretch Test: Permanent volumetric expansion suffered by the cylinder due to application of test pressure shall not exceed 7.5 percent of the total volumetric expansion at the pressure.)	-
15.2 IS 3196(Part 3) (Hydrostatic Test)	-
16 IS 3196(Part 3) (Pneumatic Leakage Test)	-
17 IS 3196(Part 3) (BURST TEST)	-
18 IS 3196(Part 3) (ACCEPTANCE TESTS )	-
18g IS 3196(Part 3) (c)Weld Joint test specimen)	-
18j IS 3196(Part 3) (d)Bend test Across weld Root Bend test,)	-
18k IS 3196(Part 3) (Face Bend test,)	-
18h IS 3196(Part 3) (c)Weld Joint test specimen)	-
18j IS 3196(Part 3) (d)Bend test Across weld Root Bend test,)	-
18k IS 3196(Part 3) (Face Bend test,)	-
18m IS 3196(Part 3) (e)Macro Examination: Body)	-
18p IS 3196(Part 3) (f) Minimum Thickness test: The thickness shall not be less than agreed finished thickness,Declared thicknes:)	-
19.2.1 (Porous Material)	-
19.2.3 (Gap between cylinder shell and porous material: Overall shrinkage of the filling material is permissible provided that the total clearance between the cylinder shell and filling material does not exceed 0.5 percent of the respective diameter or length but in no case of exceed 3.2 mm measured diametrically and longitudinally and that such clearances do not impair the functions of the filling material.)	-
19.2.4 Annex B (The porosity of the porous filling shall be in the range of 75 to 92 percent with a tolerance of ± 2 percent on nominal declared value as determined by the method prescribed in Annex B)	-
19.2.5 Annex C (The crushing strength of the porous filling shall be 2 156 kN/m2 (22 kgf/cm2 ) minimum as determined by the method prescribed in Annex C)	-
19.3 (Solvent and Acetylene Content)	-
20.2.4e) Annex E (Test of the Integrity of porous material)	-
20.3 (Elevated Temperature Test)	-
20.4 (Vibration Test)	-
20.5 (Backfire Test)	-
20.6 (Bonfire Test)	-

-
Element to be tested for material with specified requirement to be declared.Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding "-; CL 20.6 -Bonfire Test, CL 20.5 Backfire Test ,CL 20.4 Vibration Test ,Cl 20.3 Elevated Temperature Test, CL -19.2.1 Porous Material, CL 16 IS 3196(Part 3) Pneumatic Leakage Test,CL 15.1 IS 3196(Part 3) Hydrostatic Stretch Test, CL (Cl 13)-Radiographic examination"

696

IS 1239 : Part 2 (2011)

Steel tubes, tubulars and other steel fittings - Specification: Part 2 steel pipe fittings (Fifth Revision)

3400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1-Table 1 ( DIMENSIONS OF TUBULARS-Pieces )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-B )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-C )	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-A)	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-B)	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-C)	-
7.1 (Chemical Composition - Sulphur - Laddle Analysis IS 228)	-
7.1 (Chemical Composition - Phosphorus - Laddle Analysis IS 228)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; i)Alignment of threads(CL 9..2) ii)Joints(CL 10) iii)Taper screw plug test (CL11.2.2)

697

IS 7291 (1981)

Specification for high speed tool steels (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1, 5.2 & 14.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1, 5.2 & 14.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1, 5.2 & 14.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1, 5.2 & 14.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1, 5.2 & 14.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Standard has been withdrawn;

698

IS 14411 (1996)

Deltamethrin F - Specification

Rs.2300.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3 (Deltamethrin Content)	-
3.4 (Dispersibility in -Water)	-
3.5 (Acidity)	-

-
-

699

IS 1011 (2002)

Biscuits - Specification (Fourth Revision)

Rs.3280/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (General Requirement)	-
6.3 Table 2 i (Moisture)	-
6.3 Table 2 ii (Acid insoluble ash (on dry basis))	-
6.3 Table 2 iii (Acidity of extracted fat (as oleic acid))	-

-
3 PKT

700

IS 14510 (1997)

Lambda - Cyhalothrin WP - Specification

Rs.3650.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3 Table 1 v (Acidity/Alkalinity)	-
3.3 Table 1 iv (Wettability)	-
3.2 (Description)	-
3.3 Table 1 i (Lamda cyhalothrin content )	-
3.3 Table 1 iii (Suspensibility)	-
3.3 Table 1 ii (Sieving requirements material passing through 75 micron IS sieve)	-

-
excluding Cl 3.3, Table1, Sl No. I & III Lambda Cyhalothrin Content;

701

IS 7285 : Part 1 (2018)

Refillable seamless steel gas cylinders - Specification: Part 1 normalized steel cylinders (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.11 (Neck Thread)	-
6.7 (Foot Rings)	-
6.8.1 (Neck Rings)	-
7.3 (Surface Defects)	-
7.4 (Out-of-Roundness)	-
7.5 (Mean Diameter)	-
7.6 (Straightness)	-
7.7 (see Fig. 3) (Verticality)	-
7.8 (Stability)	-
7.10 a) (For cylinders of water capacity up to and including 20 litres = )	-
7.10 b) (For cylinders of water capacity exceeding 20 litres =)	-
9.2.3, Fig. 4 (Hydraulic Bursting Test)	-
9.2.4 (Pressure Cycling Test)	-
10.1.3 a) & Clause 5.4 Table 3, i) ( Tensile strength (Rg) )	-
Clauses 6.8 and 10.3.1,Table 4 iii), Sr.no.3 (Impact Test-Cylinder Diameter Dm >140 mm i) Direction- Transverse: ii) Test temperature, in °C –20)	-
Clauses 6.8 and 10.3.1,Table 4 iii), Sr.no.4 (Impact Test-Cylinder Diameter Dm ≤140 mmi) Direction-Longitudinal ii) Test temperature, in °C –20)	-
10.4.1 Table 5 ,FIG. 9 (Bend Test)	-
10.4.2 Table 5 (Flattening Test)	-
10.4.3 Table 5 (Ring-Flattening Test)	-
11.2 (Hydrostatic Stretch Test)	-
11.3 (Hardness Test)	-
13 (COLOUR IDENTIFICATION)	-
Clauses 5.2.1 and 5.4, Table 1 (Controls on Chemical Composition)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; (Cl 7.4 -Out-of-roundness,Cl 7.5) - Mean diameter,(Cl 7.6)- Straightness,(Cl 7.7) -Verticality, (Cl 7.8) -Stability, (Cl 9.2.3) -Hydraulic Burst Test,(Cl 9.2.4) -Pressure Cycling Test, (Cl 10.4.2) -Flattening test, (Cl 11.2 - Hydrostatic Stretch Test, (Cl 11.4) - Leakage test

702

IS 7226 (1974)

Specification for cold - Rolled medium, high carbon and low alloy steel strip for general engineering purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (HARDNESS TEST)	-
6 ( FREEDOM FROM DEFECTS)	-
9.1, Table 3 (i)TOLERANCE ON WIDTH)	-
9.1, Table 4 (ii)TOLERANCE ON THICKNESS)	-
9.2 ( Camber)	-
10 (SURFACE FINISH)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding Except Tungsten as per table 1;

703

IS 14550 (1998)

Hexaconazole, EC - Specification

Rs.1025.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point (Abel))	-
3.2.4 (Emulsion Stability)	-
3.3.2 (Acidity/Alkalinity)	-

-
excluding Cl. 3.3.1 Hexaconazole Content;

704

IS 16232 (2014)

Iron fortified iodized salt (Double Fortified Salt) - Food grade - Specification

11800 View breakup
For complete test facility

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Description - Iron fortified iodized salt (Double fortified salt) shall be crushed crystalline solid; white or pale pink or light grey in colour, free from contamination with clay and other extraneous adulterants and impurities)	-
3.4 - Table 1 - i (Moisture - Annex A of IS 7224)	-
3.3 (material shall pass through 4.00 mm IS sieve)	-
3.4 - Table 1 - ii (Water insoluble matter, on dry basis - A-4 of IS 253 )	-
3.4 - Table 1 - iii (Chloride content (as NaCl), on dry basis - A-4 of IS 253)	-
3.4 - Table 1 - iv (Matter insoluble in dilute HCl, on dry basis - Annex G)	-
3.4 - Table 1 - vi (Iron content (as Fe) - Annex A)	-
3.4 - Table 1 - vii- a (Iodine content, Manufacturer’s level - Annex B)	-
3.4 - Table 1 - viii - b (pH of 5 percent aqueous solution : For other forms of iron fortification - Annex C)	-
3.4 - Table 1 - ix (Sulphate (as SO4) - A-8 of IS 253)	-
3.4 - Table 1 - x (Magnesium (as Mg), water soluble - A-7 of IS 253)	-
3.4 - Table 1 - xi - b (Phosphorous (as P2O5) - For other forms of iron fortification - Annex D)	-
3.4 - Table 1 - xii (Sodium hexa meta phosphate, on dry basis - Annex E)	-
3.4 - Table 1 - xi - a (Phosphorous (as P2O5) - For iron fortification through encapsulated ferrous fumarate - Annex D)	-
3.4 - Table 1 - v (Matter soluble in water other than sodium chloride, on dry basis - A-6 of IS 253)	-

-
500 gm x 3 excluding 1-Phosphorous (as P2O5), 2-Sodium hexa meta phosphate, 3-Iron;

705

IS 15160 (2002)

Pretilachlor emulsifiable concentrate - specification

Rs.2450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point (Abel))	-
3.2.4 (Emulsion Stability)	-
3.3.1 (Pretilachlor content)	-
3.3.2 (Acidity)	-

-
-

706

IS 10325 (2000)

Square tins - 15 kg/litre for ghee, vanaspati, edible oils and bakery shortenings - Specification (Second Revision)

3700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimensions and Tolerances)	-
4.1 (Dimensions and Tolerances)	-
4.1 (Dimensions and Tolerances)	-
4.2.2 (Handle)	-
4.3.1 (Manufacture)	-
4.3.2 (Manufacture)	-
4.3.3 (Manufacture)	-
4.3.4 (Manufacture)	-
4.3.5 (Handle)	-
4.3.5 (Handle)	-
4.3.5 (Handle)	-
4.3.5 (Handle)	-
5.1 (Air-Pressure Test)	-
5.2 (Handle Pull Test)	-
5.3 (Hydraulic Pressure Test)	-
4.2.2 (Handle)	-

-
"Test facility for base metal and tin coating as per IS 1327. Sample size 5x5 cmm thickness > 3mm. Test facility complete for mechanical; " excluding Test facility for base metal and tin coating as per IS 1327 available. for material thickness < 0.8 mm only C & S can be tested.;

707

IS 8737 (2017)

Valve fittings for use with liquefied petroleum gas (LPG) cylinders for more than 5 litre water capacity - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3.1a (Tensile Strength-IS 1608)	-
4.3.1b (Elongation-IS 1608)	-
4.4 (Izod impact strength-IS 1598)	-
5.1.1a Fig 1,2 (SCREW THREADS ON THE VALVE STEM- Type 1 Threads-IS 15894)	-
7.1 (Design Requirements)	-
7.3 (Design Requirements)	-
7.4 (Design Requirements)	-
7.5 (Design Requirements)	-
7.6 (Design Requirements)	-
7.8ai Annex D of IS 9798 (All rubber and other moulded parts coming in contact with LPG in the construction of the valve shall be compatible with LPG, when tested according to Annex D of IS 9798)	-
7.8bi Annex H of IS 9798. (All rubber and other moulded parts shall be suitable for extreme climatic conditions in which the valve is likely to be used, the range of temperature being -20°C to + 65°C. The method of test shall be according to Annex H of IS 9798.)	-
4.6.2,4.6.2.1,4.6.2.2a (Moulded parts (plastics, etc) shall be subjected to immersion test (resistance to hydrocarbons)(Cl.4.6.2.1) Increase in mass :)	-
7.10 (The minimum finished wall thickness at any portion of the valve shall not be less than 2.5 mm)	-
8.1 (Stress Corrosion Test for Copper Alloy As per IS 2305)	-
8.2 (Hydrostatic Test)	-
8.3.1 (Pneumatic Test: Tightness of Joint Packing (in Valve Outlet) and Valve Spindle)	-
8.3.2 (Pneumatic Test: Tightness of Valve Spindle and Valve Housing)	-
8.3.3 (Pneumatic Test: Tightness of Joint Packing and Housing)	-
9.2a (Cycle Test)	-
9.2bi (After the cycle test, the valve shall besubjectedto the pneumatic test given in 8.3 and shall performsatisfactorily:- lPneumatic Test ,after cycle test: Tightness of Joint Packing (in Valve Outlet) and Valve Spindle)	-
9.2bii (Pneumatic Test ,after cycle test: Tightness of Valve Spindle and Valve Housing)	-
9.2biii (Pneumatic Test ,after cycle test: Tightness of Joint Packing and Housing)	-
9.3 (Operation Test)	-
9.4 (Valve Fitting Testing Torque :)	-
9.5a Table 3,Fig. 8 (Impact Test)	-
9.5bi (After the Impact test, the valve shall satisfy Pneumatic test as perCl.8.3:- lPneumatic Test ,after cycle test: Tightness of Joint Packing (in Valve Outlet) and Valve Spindle)	-
9.5bii (Pneumatic Test ,after cycle test: Tightness of Valve Spindle and Valve Housing)	-
9.5biii (Pneumatic Test ,after cycle test: Tightness of Joint Packing and Housing)	-
4.3.1a (Tensile Strength-IS 1608)	-
6.2 (VALVE OUTLET CONNECTIONS: Spring loaded self-closing Valve)	-
4.2.1Sl.No.i (Copper)	-
4.2.1Sl.No.ii (Lead)	-
4.2.1Sl.No.iii (Iron)	-
4.2.1Sl.No.iv (Manganese)	-
4.2.1Sl.No.vi (Zinc)	-
4.2.1Sl.No.v (others(inclusive of iron))	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; (Cl 4.6.1.1)-Ozone test (Resistance to ozone cracking)

708

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 13 (Workmanship)	-
Cl 15 (Length, Width & Thickness)	-
7.1 (Carbon %)	-
7.1 (Sulphur %)	-
7.1 (Phosphorus %)	-
7.1 (Manganese %)	-
7.1 (Silicon %)	-
7.1 ( Aluminium %)	-
7.1 ( Nitrogen%)	-
7.1 ( Copper %)	-
7.1 (V)	-
7.1 ( Ti)	-
7.1 (Cr)	-
7.1 (Mo)	-
7.1 ( Nb)	-
Cl. 7 (Micro Alloy)	-
Cl. 7 (CE)	-
Cl. 7 (Boron)	-
Cl. 7 (Ti+Nb+V+B)	-
Cl. 7 (Cr+Ni+Mo)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding -; i)Hole Expansion Ratio Test(CL 11)

709

IS 15182 (2002)

Propiconazole EC - Specification

Rs.2450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1 (Description)	-
3.2.2 (Cold Test)	-
3.2.3 (Flash Point (Abel))	-
3.2.4 (Emulsion Stability)	-
3.3.1 (Pretilachlor content)	-
3.3.2 (Acidity)	-

-
excluding Cl. 3.3.1 Propiconazole Content;

710

IS 14158 (1994)

Cyfluthrin WP - Specification

Rs.5600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3 Table 1 i (Cyfluthrin content )	-
3.3 Table 1 ii (Sieving requirements material passing through 75 micron IS sieve)	-
3.3 Table 1 iii (Suspensibility)	-
3.3 Table 1 iv (Acidity/Alkalinity)	-
3.3 Table 1 v (Wettability)	-

-
excluding Cl 3.3, Table1, Sl No. I & III Content & Suspensibility;

711

IS 6967 (1973)

Specification for steels for electrically welded round link chains

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Table 2 (Carbon- IS 228)	-
5.1 Table 2 (Manganese- IS 228)	-
5.1 Table 2 (Sulphur- IS 228)	-
5.1 Table 2 (Phosphorous- IS 228)	-
5.1 Table 2 (Silicon- IS 228)	-

-
-

712

IS 1660 (2009)

Wrought aluminium utensils - Specification (First Revision)

Rs 6760/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Classification Heavy/Medium/L:ight)	-
0.5 (Fabrication)	-
5.1 (The utensil shall be pressed or spun from one piece)	-
5.2 ( Body Thickness of the thinnest part of the finished utensil, mm Not declared )	-
5.2 (Lid Thickness of the finished utensil, mm)	-
6.1 & Table 1 ( i) Name of Utensil )	-
6.1 & Table 1 (ii) Shape of Utensil)	-
6.1 & Table 1 ( Nominal Size, mm)	-
6.1 & Table 1 (Inside dia, Φ D mm Not declared )	-
6.1 & Table 1 (Outside dia Ф NA)	-
6.1 & Table 1 (Height NA)	-
6.1 & Table 1 (Capacity, l NA)	-
6.1 ( Minimum sheet thickness for nominal size )	-
7.1 (HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-
7.2 (Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-
8.1 (The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-
8.2 (The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-
8.4.1.2 ( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Copper of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Magnesium of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Silicon of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Iron of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Manganese of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Zinc of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Chromium of IS 21)	-
( Clauses 4, 4.1, 4.2 and 4.3) (Titanium / other Grain of IS 21)	-
8.4.2 (A coating of thickness 25 to 100 microns is generally required)	-
8.4.3 (Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-
8.4.4 (The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-
8.4.4 (The film will appear dark grey when wet. )	-
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-
9 (The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-
10 (Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-
Clause 8.6.1 (Performance test)	-
Clause 8.6.2 (Ground Nut Oil Test for Leakage)	-
5.4 (Qualitative and Anodized Coating)	-
5.5 (Qualitative and Anodized Coating)	-
8.3 (Anodized Coating)	-
8.5 (Plastic Coating)	-
8.1 (Qualitative)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm; excluding TF not available for 1. Coating test 2. Hard Anodized;

713

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Workmanship)	-
Cl 9 (Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-
6.1 (Carbon %)	-
6.1 (Sulphur %)	-
6.1 (Phosphorus %)	-
6.1 (Manganese %)	-
6.1 (Silicon %)	-
6.1 ( Aluminium %)	-
6.1 ( Nitrogen%)	-
6.1 (Boron)	-
6.1 ( Copper %)	-
6.1 ( Ti)	-
6.1 (V)	-
6.1 ( Nb)	-
6.1 (Microalloying)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

714

IS 336 (1973)

Specification for ether

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl no .3.2 (Odour and Taste )	-
Cl no .3.3.1 (Composition )	-
Cl no .3.4 (Solubility )	-
Cl no .3.5 [ Table 1, Sl no.(i) ] Appendix A 2 (Relative density at 20 °C Solvent Grade )	-
Cl no .3.5 [ Table 1, Sl no.(iv) ] Appendix A 5 (Residue on Evaporation )	-
Cl no .3.5 [ Table 1, Sl no.(v) ] Appendix A 6 (Methyl alcohol )	-
Cl no .3.5 [ Table 1, Sl no.(vi) ] Appendix A 7 (Aldehydes and acetone )	-
Cl no .3.5 [ Table 1, Sl no.(vii) ] Appendix A 8 (Sulphurous acids and other free acids )	-

-
excluding iii) Distillation range;

715

IS 2028 (2004)

Open jaw wrenches (Spanners) - Specification (Fijih Revision)

Rs.3700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Dimensions- a)	-
3.1 (Dimensions- b)	-
3.1 (Dimensions- l)	-
3.2, 3.3, 3.4 (Dimensions- a)	-
3.2, 3.3, 3.4 (Dimensions- b1)	-
3.2, 3.3, 3.4 (Dimensions- b2)	-
3.2, 3.3, 3.4 (Dimensions- l)	-
5 (Hardness- upto 32 mm)	-
5 (Hardness- over 32 mm)	-
6 (Workmanship And Finish)	-
6 (Workmanship And Finish)	-

-
Please refer status of IS 3748 for test facility status of Chemical disciplince.; excluding -; i)Torque testing(CL 8)

716

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

9710 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 8 (Press)	-
Cl 9 (Strainage Embrittlement)	-
Cl 10 (Erichsen Cupping)	-
Cl 13 (Length, Width & Thickness)	-
6.1 (Carbon %)	-
6.1 (Sulphur %)	-
6.1 (Phosphorus %)	-
6.1 (Manganese %)	-
6.1 (Silicon %)	-
6.1 ( Aluminium %)	-
6.1 (Nitrogen%)	-

-
Sample size shall be minimum dia> 3mm and thickness > 0.8 mm;

717

IS 14276 (2016)

Cement bonded particle boards - Specification (First Revision)

11797 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Finish)	-
7 (Dimensions and Tolerances)	-
8.5 (Workability)	-
10.3, Table-1 (Test for Density)	-
10.5, Table-1 (Test for Water Absorption)	-
10.6, Table-1 (Test for swelling in water)	-
10.7, Table-1 (Test for modulus of Rupture)	-
10.8, Table-1 (Test for modulus of Elasticity)	-
10.9, Table-1 (Test for tensile strength perpendicular to Surface)	-
10.1, Table-1 (Test for Screw Withdrawal Strength)	-
Clause 8.2 Table 1 (Moisture content)	-

-
"Test facility not available for 10.8 Tensile Strength Perpendicular to Surface After Ageing, 10.10 -Abrasion Resistance, 10.11 - Resistance to Steam, 10.14 - Resistance to Stain ,; " Sample Test Parameter not available in CL: 10.5 Test for Water Absorption, 10.6 Test for Swelling in Water, 10.7 Test for Modulus of Rupture(Wet),10.8 Test for Modulus of Elasticity (Wet), 10.9Test for Tensile Strength Perpendicular to Surface (accelerated ageing test)," SIZE: 2 Boards Of Full Size Sample Size without dimensional measurements: Length-1200 mm, width-1200

718

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

Rs.12770.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 3.3 (Compressive Strength, At 3days & 7 days)	-
Cl 3.2 (Initial & Final)	-
Clause 3.4 (Chloride content)	-
Cl 3.1 (The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-
Clause 3.1 (Permeability to water of cement mortar with Water proofing compound)	-

-
complete

719

IS 13785 (1993)

Pesticide - Dodine WP - Specification

Rs.3350.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3 Table 1 i (Dodine content)	-
3.3 Table 1 ii (Sieving requirements material passing through 75 micron IS sieve)	-
3.3 Table 1 iv (Acidity/Alkalinity)	-
3.3 Table 1 v (Wettability)	-

-
-

720

IS 13692 (1993)

Metalaxyl mancqzeb WP - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2 (Description)	-
3.3 Table 1 i (Metalaxyl content,)	-
3.3 Table 1 iii (Sieving requirements material passing through 75 micron IS sieve)	-
3.3 Table 1 v (Wettability)	-

-
excluding Table1 Cl. 3.3, Sl. No. 2 Metalaxyl Content;

Bureau of Indian Standards

The National Standards Body of India

BIS, Central Laboratory (CL)

20/9, Site 4, Sahibabad Industrial Area, Sahibabad, Ghaziabad, Ghaziabad, Uttar Pradesh, 201010

- sample@bis.gov.in

Scope List