BIS - LIMS (Laboratory Information Management System)

Sleen India Biz venture Private Limited, Agra

RAHANKALAN ROAD, PART 295, BLOCK-A KUBERPUR, 300 METER FROM RAILWAY CROSSING CHALESHAR ROAD, Agra, Uttar Pradesh, India, 282006, Agra, Agra, Uttar Pradesh, 282006

8193022228 sleen.info@gmail.com

Scope List

Reset

150 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2932 (2013)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

23500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3(Freedom from Coarse Particles)	-	1200	-
6.4(Skin Formation)	-	1200	-
6.5(Thinning Properties)	-	1200	-
6.6(Application Properties)	-	1200	-
6.8(Lead Restriction)	-	1700	-
6.9 Table 2 (1) a. Consistency ( Undercoating and Finishing ) )	-	1200	-
6.9 Table 2 (1) b. Viscosity by ford 80-120 s )	-	1200	-
6.9 Table 2 ( 2) Mass, ( Under coating ) )	-	1200	-
6.9 Table 2 ( 2) Mass, (Finishing ) )	-	1200	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Under coating ) )	-	1200	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Finishing ) )	-	1200	-
6.9 Table 2 (b) Hard dry ( Under coating ) )	-	1200	-
6.9 Table 2 (b) Hard dry, (Finishing ) )	-	1200	-
6.9 Table 2 (c) Tack free ( Under coating (Finishing ) )	-	1200	-
6.9 Table 2 (4) a) Finish (Under coating ) )	-	1200	-
6.9 Table 2 (4) a) Finish (Finishing) )	-	1200	-
6.9 Table 2 (b) ) Gloss 60º (Under coating ) )	-	1200	-
6.9 Table 2 (b) ) Gloss 60º (Finishing) )	-	1200	-
6.9 Table 2 (5) Fineness of grind,(Under coating ))	-	1200	-
6.9 Table 2 (5) Fineness of grind,(Finishing))	-	1200	-
6.9 Table 2 (6) Colour , (Finishing))	-	1200	-
6.9 Table 2 (7) Flexibility and adhesion: a) Scratch hardness No such scratch as to show the bare metal after Clause 3 of — (Load 1 000 g) ( Under coating & Finishing ) )	-	1200	-
6.9 Table 2 (b) Bend test (with 6.25 mm 48 h of air in type 1 apparatus) ( Under coating & Finishing ) )	-	1200	-
6.9 Table 2 (8) Flash point ( Under coating & Finishing ) )	-	1200	-
6.9 Table 2 (9) Composition: a) Volume solids ( Under coating ))	-	3000	-
6.9 Table 2 (9) Composition: a) Volume solids ( Finishing))	-	3000	-
6.9 Table 2 (9) Composition:b) Phthalic anhydride content of non-volatile vehicle ( Under coating & Finishing ))	-	3000	-
6.9 Table 2 (10) Resistance to acid ( Under coating & Finishing ))	-	1200	-
6.9 Table 2 (11) Resistance to alkali ( Under coating & Finishing ))	-	1200	-
6.9 Table 2 (12) Accelerated storage stability test ( Under coating & Finishing ))	-	1200	-
6.9 Table 2 (13) Keeping properties ( Under coating & Finishing ))	-	2000	-
6.9 Table 2 (14) Wet opacity ( Under coating & Finishing ))	-	1200	-
6.3(Freedom from Coarse Particles)	-	0	Repeated Clause.
6.4(Skin Formation)	-	0	Repeated Clause.
6.5(Thinning Properties)	-	0	Repeated Clause.
6.6(Application Properties)	-	0	Repeated Clause.
6.8(Lead Restriction)	-	0	Repeated Clause.
6.9 Table 2 (1) a. Consistency ( Undercoating and Finishing ) )	-	0	Repeated Clause.
6.9 Table 2 (1) b. Viscosity by ford 80-120 s )	-	0	Repeated Clause.
6.9 Table 2 ( 2) Mass, ( Under coating ) )	-	0	Repeated Clause.
6.9 Table 2 ( 2) Mass, (Finishing ) )	-	0	Repeated Clause.
6.9 Table 2 (3) Drying time, a) Surface dry, ( Under coating ) )	-	0	Repeated Clause.
6.9 Table 2 (3) Drying time, a) Surface dry, ( Finishing ) )	-	0	Repeated Clause.
6.9 Table 2 (b) Hard dry ( Under coating ) )	-	0	Repeated Clause.
6.9 Table 2 (b) Hard dry, (Finishing ) )	-	0	Repeated Clause.
6.9 Table 2 (c) Tack free ( Under coating (Finishing ) )	-	0	Repeated Clause.
6.9 Table 2 (4) a) Finish (Under coating ) )	-	0	Repeated Clause.
6.9 Table 2 (4) a) Finish (Finishing) )	-	0	Repeated Clause.
6.9 Table 2 (b) ) Gloss 60º (Under coating ) )	-	0	Repeated Clause.
6.9 Table 2 (b) ) Gloss 60º (Finishing) )	-	0	Repeated Clause.
6.9 Table 2 (5) Fineness of grind,(Under coating ))	-	0	Repeated Clause.
6.9 Table 2 (5) Fineness of grind,(Finishing))	-	0	Repeated Clause.
6.9 Table 2 (6) Colour , (Finishing))	-	0	Repeated Clause.
6.9 Table 2 (7) Flexibility and adhesion: a) Scratch hardness No such scratch as to show the bare metal after Clause 3 of — (Load 1 000 g) ( Under coating & Finishing ) )	-	0	Repeated Clause.
6.9 Table 2 (b) Bend test (with 6.25 mm 48 h of air in type 1 apparatus) ( Under coating & Finishing ) )	-	0	Repeated Clause.
6.9 Table 2 (8) Flash point ( Under coating & Finishing ) )	-	0	Repeated Clause.
6.9 Table 2 (9) Composition: a) Volume solids ( Under coating ))	-	0	Repeated Clause.
6.9 Table 2 (9) Composition: a) Volume solids ( Finishing))	-	0	Repeated Clause.
6.9 Table 2 (9) Composition:b) Phthalic anhydride content of non-volatile vehicle ( Under coating & Finishing ))	-	0	Repeated Clause.
6.9 Table 2 (10) Resistance to acid ( Under coating & Finishing ))	-	0	Repeated Clause.
6.9 Table 2 (11) Resistance to alkali ( Under coating & Finishing ))	-	0	Repeated Clause.
6.9 Table 2 (12) Accelerated storage stability test ( Under coating & Finishing ))	-	0	Repeated Clause.
6.9 Table 2 (13) Keeping properties ( Under coating & Finishing ))	-	0	Repeated Clause.
6.9 Table 2 (14) Wet opacity ( Under coating & Finishing ))	-	0	Repeated Clause.
6.7.1.3(QUV apparatus)	-	8000	-
6.2(Condition in container)	-	0	Repeated Clause.
7.2(Marking)	-	250	Repeated Clause.
7.3(BIS Certification Marking)	-	250	0
6.1.1(General- Rosin test)	-	500	-
6.1.2(Total Non-Volatile Content)	-	500	-
6.7.2(Bulk supply)	-	2000	-
6.7.2.1(Bulk supply-Gloss (specular 60º) retention)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics- Colour)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics- Colour)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics-Freedom from Checking)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics-Freedom from Cracking)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics-Freedom from Flaking)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics-Freedom from Chalking)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics-Freedom from Spotting)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics-Freedom from Blisters and Corrosion)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
6.7.2.2(Bulk supply- Film characteristics-Protection against corrosion)	-	0	complete Test price for cl. 6.7.2 is 2000/-.
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 1. Visual observation (Corrosion and odour of putrefaction, rancidity or souring) [Cl 3.1 of IS 101 (Part 6/Sec 2)]")	-	0	Repeated Clause.
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 2. Change in skinning [Cl.3.1,Table 1 of IS 101 (Part 6/Sec 2)]")	-	0	Repeated Clause.
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 3. Degree of settling [Cl.3.2,Table 2 of IS 101 (Part 6/Sec 2)]")	-	0	Repeated Clause.
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 4. Observation of dried film [Cl.3.4, Table 1 of IS 101 (Part 6/Sec 2)]")	-	0	Repeated Clause.
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 5. Loss of mass resulting from Storage [Cl.3.5 of IS 101 (Part 6/Sec 2)]")	-	0	Repeated Clause.
6.7.1.3(QUV apparatus)	-	0	-
6.2(Condition in container)	-	0	-
7.2(Marking)	-	0	-
7.3(BIS Certification Marking)	-	0	-
6.1.1(General- Rosin test)	-	0	-
6.1.2(Total Non-Volatile Content)	-	0	-
6.7.2(Bulk supply)	-	0	-
6.7.2.1(Bulk supply-Gloss (specular 60º) retention)	-	0	-
6.7.2.2(Bulk supply- Film characteristics- Colour)	-	0	-
6.7.2.2(Bulk supply- Film characteristics- Colour)	-	0	-
6.7.2.2(Bulk supply- Film characteristics-Freedom from Checking)	-	0	-
6.7.2.2(Bulk supply- Film characteristics-Freedom from Cracking)	-	0	-
6.7.2.2(Bulk supply- Film characteristics-Freedom from Flaking)	-	0	-
6.7.2.2(Bulk supply- Film characteristics-Freedom from Chalking)	-	0	-
6.7.2.2(Bulk supply- Film characteristics-Freedom from Spotting)	-	0	-
6.7.2.2(Bulk supply- Film characteristics-Freedom from Blisters and Corrosion)	-	0	-
6.7.2.2(Bulk supply- Film characteristics-Protection against corrosion)	-	0	-
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 1. Visual observation (Corrosion and odour of putrefaction, rancidity or souring) [Cl 3.1 of IS 101 (Part 6/Sec 2)]")	-	0	-
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 2. Change in skinning [Cl.3.1,Table 1 of IS 101 (Part 6/Sec 2)]")	-	0	-
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 3. Degree of settling [Cl.3.2,Table 2 of IS 101 (Part 6/Sec 2)]")	-	0	-
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 4. Observation of dried film [Cl.3.4, Table 1 of IS 101 (Part 6/Sec 2)]")	-	0	-
" 6.9 Table 2, xiii) Keeping properties "("Keeping properties 5. Loss of mass resulting from Storage [Cl.3.5 of IS 101 (Part 6/Sec 2)]")	-	0	-

15 May, 2027

-
Included w.e.f. 07.08.2025

IS 17514 (2025)

Reusable Sanitary Pad/Sanitary Napkin/Period Panties - Specification (First Revision)

All size

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1(Material- cover or the top sheet)	-	500	-
Cl-3.2(Material- absorbent core;)	-	500	-
Cl-3.3(Material- bottom layer.)	-	500	-
Cl-4(MANUFACTURE, WORKMANSHIP AND FINISH)	-	500	-
Cl-5(FASTENING MECHANISM)	-	500	-
Cl-6, Table-1(Length (mm) (Absorbent Core Only))	-	500	-
Cl-6, Table-1(Width (mm) (Absorbent Core Only))	-	500	-
Cl-7(WASHING, DRYING AND HANDLING INSTRUCTION)	-	500	-
Cl-8, Table-2 (i) (a)("Colour fastness to rubbing: Dry ")	-	1500	-
Cl-8, Table-2 (i) (b)(Colour fastness to rubbing: Wet)	-	0	Complete testing for cl. 8 table-2(i) is 1500/-.
Cl-8, Table-2 (ii) (a)("Colour fastness to perspiration (acidic and alkaline): Colour change ")	-	2000	-
Cl-8, Table-2 (ii) (b)(Colour fastness to perspiration (acidic and alkaline): Staining)	-	0	Complete testing for cl. 8 table-2(ii) is 1500/-.
Cl-8, Table-2 (iii) (a)(Colour fastness to washing: Colour change)	-	2000	-
Cl-8, Table-2 (iii) (b)(Colour fastness to washing: Staining)	-	0	Complete testing for cl. 8 table-2(iii) is 2000/-.
Cl-8, Table-2 (iv)("Dimensional stability to washing, percentage, Max Length and width")	-	1000	-
Cl-9.1(pH Value)	-	1000	-
Cl-9.2(Ability to Withstand Pressure after Absorption)	-	2000	-
Cl-9.3(Hygiene Testing Requirement)	-	500	-
Cl-9.5(Phthalate Test)	-	5000	-
Cl-12(Marking)	-	500	-
Cl-9.3.1(Bacterial and Fungal Bioburden)	-	1500	-
Cl-3.1(Material- cover or the top sheet)	-	0	Repeated Clause.
Cl-3.2(Material- absorbent core;)	-	0	Repeated Clause.
Cl-3.3(Material- bottom layer.)	-	0	Repeated Clause.
Cl-4(MANUFACTURE, WORKMANSHIP AND FINISH)	-	0	Repeated Clause.
Cl-5(FASTENING MECHANISM)	-	0	Repeated Clause.
Cl-6, Table-1(Length (mm) (Absorbent Core Only))	-	0	Repeated Clause.
Cl-6, Table-1(Width (mm) (Absorbent Core Only))	-	0	Repeated Clause.
Cl-7(WASHING, DRYING AND HANDLING INSTRUCTION)	-	0	Repeated Clause.
Cl-8, Table-2 (i) (a)("Colour fastness to rubbing: Dry ")	-	0	Repeated Clause.
Cl-8, Table-2 (i) (b)(Colour fastness to rubbing: Wet)	-	0	Repeated Clause.
Cl-8, Table-2 (ii) (a)("Colour fastness to perspiration (acidic and alkaline): Colour change ")	-	0	Repeated Clause.
Cl-8, Table-2 (ii) (b)(Colour fastness to perspiration (acidic and alkaline): Staining)	-	0	Repeated Clause.
Cl-8, Table-2 (iii) (a)(Colour fastness to washing: Colour change)	-	0	Repeated Clause.
Cl-8, Table-2 (iii) (b)(Colour fastness to washing: Staining)	-	0	Repeated Clause.
Cl-8, Table-2 (iv)("Dimensional stability to washing, percentage, Max Length and width")	-	0	Repeated Clause.
Cl-9.1(pH Value)	-	0	Repeated Clause.
Cl-9.2(Ability to Withstand Pressure after Absorption)	-	0	Repeated Clause.
Cl-9.3(Hygiene Testing Requirement)	-	0	Repeated Clause.
Cl-9.5(Phthalate Test)	-	0	Repeated Clause.
Cl-12(Marking)	-	0	Repeated Clause.
Cl-9.3.1(Bacterial and Fungal Bioburden)	-	0	Repeated Clause.
Cl-9.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus)	-	2000	-
Cl-9.3.3(Good Manufacturing Practice Guideline for Hygiene Requirement)	-	500	-

15 May, 2027

-
Included w.e.f 14.10.2025 Exclusion: Cl-9.4 (Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization)

IS 3521 : Part 5 (2021)

Personal Fall Arrest Systems Specification Part 5 Connectors with self-closing and self-locking gates

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No. 4.1(General requirement)	-	2000	-
Clause No. 4.2.1(" Gate-face resistance ")	-	5000	-
Clause No. 4.2.2(" Gate side-load resistance ")	-	5000	-
Clause No. 4.3("Static strength ")	-	8000	-
Clause No. 4.4(" Corrosion resistance ")	-	7000	-
Clause No. 6.2(Marking)	-	1000	-
Clause No. 6.3(Packaging)	-	1000	-
Clause No. 4.1(General requirement)	-	0	-
Clause No. 4.2.1(" Gate-face resistance ")	-	0	-
Clause No. 4.2.2(" Gate side-load resistance ")	-	0	-
Clause No. 4.3("Static strength ")	-	0	-
Clause No. 4.4(" Corrosion resistance ")	-	0	-
Clause No. 6.2(Marking)	-	0	-
Clause No. 6.3(Packaging)	-	0	-

15 May, 2027

-
Included w.e.f 28.07.2025

IS 12361 (2023)

Partially Hydrogenated Rice Bran Fatty Acids - Specification (first revision of IS 12361)

13200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Description)	-	500	-
3.3 Table 1 (i)(Moisture)	-	1200	-
3.3 Table 1 (ii)(Saponification value)	-	1500	-
3.3 Table 1 (iii)(Acid value shall not differfrom saponification value)	-	1500	-
3.3 Table 1 (iv)(Iodine Value)	-	1500	-
3.3 Table 1 (v)(Mineral Acidity)	-	1000	-
3.3 Table 1 (vi)(Ash)	-	1000	-
3.3 Table 1 (vii)(Unsaponifiable matter)	-	2000	-
3.3 Table 1 (viii)(Titre)	-	2000	-
3.3 Table 1 (ix)(Colour in a 1-in cell on the Lovibond scale expressed as Y + 5R)	-	1000	-

15 May, 2027

-
Included w.e.f.09.10.2025

IS 12069 (2023)

Coconut Fatty Acids - Specification (first revision of IS 12069)

Grade-1 and Grade-2

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description)	-	250	-
4.2(Description)	-	250	-
4.3 Table 1 (i)(Moisture)	-	500	-
4.3 Table 1 (ii)(Saponification value)	-	1000	-
4.3 Table 1 (iii)(Acid value differ from Saponification value)	-	1000	-
4.3 Table 1 (iv)(Iodine value)	-	1500	-
4.3 Table 1 (v)(Mineral acidity)	-	1000	-
4.3 Table 1 (vi)(Ash,)	-	500	-
4.3 Table 1 (vii)(Unsaponifiable matter)	-	1000	-
4.3 Table 1 (viii)(Titre,)	-	1500	-
4.3 Table 1 (ix)(Flash point)	-	1000	-
4.4 Table 2 (i)(C6 : 0)	-	5000	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4 Table 2 (ii)(C8 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4 Table 2 (iii)(C10 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4 Table 2 (iv)(C12 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (v)(C14 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (vi)(C16 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (vii)(C16 :1)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (viii)(C17 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (ix)(C17 : 1)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (x)(C18 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xi)(C18 : 1)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xii)(C18 : 2)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xiii)(C18 : 3)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xiv)(C20 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xv)(C20 : 1)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xvi)(C20 : 2)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xvii)(C22 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xviii)(C22 : 1)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xix)(C22 : 2)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xx)(C24 : 0)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.4Table 2 (xxi)(C24 : 1)	-	0	Complete test price for Fatty Acid Cl. 4.4, Table 2 is 5000/-.
4.3 Table 1 (ix)(Colour,)	-	500	-

15 May, 2027

-
Included w.e.f.23.07.2025

IS 12068 (1987)

Specification for rice bran fatty acids

12300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1/3.1.1/3.2(Description - IS 12068:1987)	-	500	-
3.3, 6.1 Table 1 (i)(Moisture - IS 548 (Part 1/Sec 2) : 2021)	-	1000	-
3.3, 6.1 Table 1 (ii)(Saponification - IS 548 (Part 1/Sec 2) : 2021)	-	1300	-
3.3, 6.1 Table 1 (iii)(Acid value - IS 548 (Part 1/Sec 2) : 2021)	-	1000	-
3.3, 6.1 Table 1 (iv)(Iodine Value - IS 548 (Part 1/Sec 2) : 2021)	-	2500	-
3.3, 6.1 Table 1 (v)(Mineral Acidity - IS 12068:1987)	-	1000	-
3.3, 6.1 Table 1 (vi)(Ash - IS 12068:1987)	-	500	-
3.3, 6.1 Table 1 (vii)(Unsaponifiable matter - IS 548 (Part 1/Sec 2) : 2021)	-	1000	-
3.3, 6.1 Table 1 (viii)(Titre - IS 548 (Part 1/Sec 2) : 2021)	-	2000	-
3.3, 6.1 Table 1 (ix)(Colour)	-	500	-
3.3, 6.1 Table 1 (x)(Flash Point - IS 1448 (P-21))	-	1000	-

15 May, 2027

-
Included w.e.f.23.07.2025

IS 12067 (2023)

Palm fatty acids - Specification (first revision of IS 12067)

All Grades

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1&4.2(Description)	-	800	-
Cl.4.3 (i)(Moisture - 6 of IS 548 (Part 1/Sec 2))	-	1200	-
Cl. 4.3 (ii)(Saponification Value - 16 of IS 548 (Part 1/Sec 2))	-	1500	-
Cl. 4.3 (iii)(Acid Value - 8 of IS 548 (Part 1/Sec 2))	-	1000	-
Cl. 4.3 (iv)(Iodine Value - 15 of IS 548 (Part 1/Sec 2))	-	1500	-
Cl. 4.3 (v)(Mineral Acidity - ANNEX A2 of IS 12067:2023)	-	1200	-
Cl. 4.3 (vi)(Ash - ANNEX A1 of IS 12067:2023)	-	800	-
Cl. 4.3 (vii)(Unsaponifiable matter - 9 of IS 548 (Part 1/ Sec 2))	-	1500	-
Cl. 4.3 (viii)(Titre Test - 13 of IS 548 (Part 1/Sec 2))	-	1500	-
Cl. 4.3 (ix)(Colour - 14.1 of IS 548 (Part 1/Sec 2))	-	2000	-
Cl. 4.3 (x)(Flash point - IS 1448 (Part 21))	-	2000	-
Cl. 4.4(Fatty Acid Composition of Palm Fatty Acids)	-	0	-
4.1(Description - IS 12067:2023)	-	0	-
4.2(Description - IS 12067:2023)	-	0	-
4.3, Table 1 (i)(Moisture - IS 548 (Part 1/Sec 2) : 2021)	-	0	-
4.3, Table 1 (ii)(Saponification - IS 548 (Part 1/Sec 2) : 2021)	-	0	-
4.3, Table 1 (iii)(Acid value shall not differ from saponification value - IS 548 (Part 1/Sec 2) : 2021)	-	0	-
4.3, Table 1 (iv)(Iodine Value - IS 548 (Part 1/Sec 2) : 2021)	-	0	-
4.3, Table 1 (v)(Mineral Acidity - IS 12067:1987)	-	0	-
4.3, Table 1 (vi)(Ash - IS 12067:1987)	-	0	-
4.3, Table 1 (vii)(Unsaponifiable matter - IS 548 (Part 1/Sec 2) : 2021)	-	0	-
4.3, Table 1 (viii)(Titre - IS 548 (Part 1/Sec 2) : 2021)	-	0	-
4.3, Table 1 (ix)(Colour, 1-inch cell, Y +5R)	-	0	-
4.3, Table 1 (x)(Flash Point - IS 1448 (P-21))	-	0	-
4.4, Table 2 (i)(C6 : 0)	-	0	-
4.4, Table 2 (ii)(C8 : 0)	-	0	-
4.4, Table 2 (iii)(C10 : 0)	-	0	`
4.4, Table 2 (iv)(C12 : 0)	-	0	-
4.4, Table 2 (v)(C14 : 0)	-	0	-
4.4, Table 2 (vi)(C16 : 0)	-	0	-
4.4, Table 2 (vii)(C16 :1)	-	0	-
4.4, Table 2 (viii)(C17 : 0)	-	0	-
4.4, Table 2 (ix)(C17 : 1)	-	0	-
4.4, Table 2 (x)(C18 : 0)	-	0	-
4.4, Table 2 (xi)(C18 : 1)	-	0	-
4.4, Table 2 (xii)(C18 : 2)	-	0	-
4.4, Table 2 (xiii)(C18 : 3)	-	0	-
4.4, Table 2 (xiv)(C20 : 0)	-	0	-
4.4, Table 2 (xv)(C20 : 1)	-	0	`
4.4, Table 2 (xvi)(C20 : 2)	-	0	-
4.4, Table 2 (xvii)(C22 : 0)	-	0	-
4.4, Table 2 (xviii)(C22 : 1)	-	0	-
4.4, Table 2 (xix)(C22 : 2)	-	0	-
4.4, Table 2 (xx)(C24 : 0)	-	0	-
4.4, Table 2 (xxi)(C24 : 1)	-	0	-

15 May, 2027

-
Included w.e.f.23.07.2025

IS 13601 (1993)

Ethylene vinyl acetate (Eva) copolymers for its safe use in contact with foodstuffs, pharmaceuticals and drinking water - Specification

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Vinyl Acetate (VA) Content,% of Annex B)	-	3000	-
4.1.2(Additive Concentrate,%)	-	3000	-
4.2(Material,% of IS 13349)	-	7000	-
4.3(Pigments and Colourants of IS 9833)	-	7000	-
4.4(Overall Migration of IS 9845)	-	4000	-
4.1.1(Vinyl Acetate (VA) Content,% of Annex B)	-	0	-
4.1.2(Additive Concentrate,%)	-	0	-
4.2(Material,% of IS 13349)	-	0	-
4.3(Pigments and Colourants of IS 9833)	-	0	-
4.4(Overall Migration of IS 9845)	-	0	-
4.1.1(Vinyl Acetate (VA) Content)	-	0	-
4.1.2(Additive Concentrates)	-	0	-
4.2(Material)	-	0	-
4.3(Pigments and Colourants)	-	0	-
4.4(Overall Migration)	-	0	-
4.5(Storage and Control)	-	250	-
5(Packing and Marking)	-	250	-

15 May, 2027

-
-

IS 17442 (2020)

Vinyl Chloride Monomer ” Specification

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.1,Table-1,Sl no.1(Appearance and colour, Annex- A)	-	2000	-
Clause 3.1,Table-1,Sl no.2(Water content in ppm, Annex-B/IS 2362/ASTM E203)	-	2500	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	4000	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	0	-
Clause 3.1,Table-1,Sl no.4(Non-volatile matter in ppm, Annex-D)	-	2000	-
Clause 3.1,Table-1,Sl no.5(Total iron by mass in ppm, Annex-E)	-	3000	-
Clause 3.1,Table-1,Sl no.6(Purity, percent in mass, Annex-F/ASTM D5507)	-	4000	-
Clause 3.1,Table-1,Sl no.1(Appearance and colour, Annex- A)	-	0	-
Clause 3.1,Table-1,Sl no.2(Water content in ppm, Annex-B/IS 2362/ASTM E203)	-	0	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	0	-
Clause 3.1,Table-1,Sl no.4(Non-volatile matter in ppm, Annex-D)	-	0	-
Clause 3.1,Table-1,Sl no.5(Total iron by mass in ppm, Annex-E)	-	0	-
Clause 3.1,Table-1,Sl no.6(Purity, percent in mass, Annex-F/ASTM D5507)	-	0	-
3.1-Table 1-(i)(Appearance and colour)	-	0	-
3.1-Table 1-(ii)(Water content in ppm, Max)	-	0	-
3.1-Table 1-(iii)(Acidity by mass in ppm, Max)	-	0	-
3.1-Table 1-(iv)(Non-volatile matter in ppm, Max)	-	0	-
3.1-Table 1-(v)(Total iron by mass in ppm, Max)	-	0	-
3.1-Table 1-(vi)(Purity, percent in mass, Min)	-	0	-
3.2(Quality of Reagents)	-	500	-
4(Packing and Marking)	-	500	-
Clause 3.1,Table-1,Sl no.1(Appearance and colour, Annex- A)	-	0	-
Clause 3.1,Table-1,Sl no.2(Water content in ppm, Annex-B/IS 2362/ASTM E203)	-	0	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	0	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	0	-
Clause 3.1,Table-1,Sl no.4(Non-volatile matter in ppm, Annex-D)	-	0	-
Clause 3.1,Table-1,Sl no.5(Total iron by mass in ppm, Annex-E)	-	0	-
Clause 3.1,Table-1,Sl no.6(Purity, percent in mass, Annex-F/ASTM D5507)	-	0	-
Clause 3.1,Table-1,Sl no.1(Appearance and colour, Annex- A)	-	0	-
Clause 3.1,Table-1,Sl no.2(Water content in ppm, Annex-B/IS 2362/ASTM E203)	-	0	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	0	-
Clause 3.1,Table-1,Sl no.4(Non-volatile matter in ppm, Annex-D)	-	0	-
Clause 3.1,Table-1,Sl no.5(Total iron by mass in ppm, Annex-E)	-	0	-
Clause 3.1,Table-1,Sl no.6(Purity, percent in mass, Annex-F/ASTM D5507)	-	0	-
3.1-Table 1-(i)(Appearance and colour)	-	0	-
3.1-Table 1-(ii)(Water content in ppm, Max)	-	0	-
3.1-Table 1-(iii)(Acidity by mass in ppm, Max)	-	0	-
3.1-Table 1-(iv)(Non-volatile matter in ppm, Max)	-	0	-
3.1-Table 1-(v)(Total iron by mass in ppm, Max)	-	0	-
3.1-Table 1-(vi)(Purity, percent in mass, Min)	-	0	-
3.2(Quality of Reagents)	-	0	-
4(Packing and Marking)	-	0	-
Clause 3.1,Table-1,Sl no.1(Appearance and colour, Annex- A)	-	0	-
Clause 3.1,Table-1,Sl no.2(Water content in ppm, Annex-B/IS 2362/ASTM E203)	-	0	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	0	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	0	-
Clause 3.1,Table-1,Sl no.4(Non-volatile matter in ppm, Annex-D)	-	0	-
Clause 3.1,Table-1,Sl no.5(Total iron by mass in ppm, Annex-E)	-	0	-
Clause 3.1,Table-1,Sl no.6(Purity, percent in mass, Annex-F/ASTM D5507)	-	0	-
Clause 3.1,Table-1,Sl no.1(Appearance and colour, Annex- A)	-	0	-
Clause 3.1,Table-1,Sl no.2(Water content in ppm, Annex-B/IS 2362/ASTM E203)	-	0	-
Clause 3.1,Table-1,Sl no.3(Acidity by mass in ppm, Annex-C)	-	0	-
Clause 3.1,Table-1,Sl no.4(Non-volatile matter in ppm, Annex-D)	-	0	-
Clause 3.1,Table-1,Sl no.5(Total iron by mass in ppm, Annex-E)	-	0	-
Clause 3.1,Table-1,Sl no.6(Purity, percent in mass, Annex-F/ASTM D5507)	-	0	-
3.1-Table 1-(i)(Appearance and colour)	-	0	-
3.1-Table 1-(ii)(Water content in ppm, Max)	-	0	-
3.1-Table 1-(iii)(Acidity by mass in ppm, Max)	-	0	-
3.1-Table 1-(iv)(Non-volatile matter in ppm, Max)	-	0	-
3.1-Table 1-(v)(Total iron by mass in ppm, Max)	-	0	-
3.1-Table 1-(vi)(Purity, percent in mass, Min)	-	0	-
3.2(Quality of Reagents)	-	0	-
4(Packing and Marking)	-	0	-

15 May, 2027

-
Included w.e.f.23.07.2025

IS 3521 : Part 1 (2021)

Personal Fall Arrest Systems Specification Part 1 Full Body Harness Fourth Revision

44500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3.2.1(Breaking strength of Synthetic fibre)	-	500	-
4.3.2.1(Breaking strength of webbing)	-	3000	-
4.3.2.2(Width of the webbing)	-	500	-
4.3.2.3(No of stitches per cm)	-	500	-
4.3.2.4(Flammability)	-	4000	-
4.4(Thickness of metal plating)	-	500	-
4.4(Corrosion resistance)	-	5000	-
4.5(Buckle Uncoupling and Slippage)	-	500	-
4.6(Static Strength)	-	4000	-
4.7(Dynamic Performance)	-	6000	-
4.9(Static Suspension Angle Test for Class AE FBH)	-	3000	-
4.8(Static Suspension Test)	-	3000	-
4.9(Static Suspension Angle Test for Class AE FBH)	-	0	-
5.2(Corrosion Test)	-	0	-
5.3(Buckle Shake Test)	-	500	-
5.8(Static Suspension Test for Fall-arrest Attachment Elements)	-	3000	-
5.9(Static suspension Angle Test for Class AE FBH)	-	0	-
5.10(Flammability Resistance Test)	-	0	-
5.7(Dynamic Performance Tests)	-	0	-
5.4(Static Strength Test for Fall-arrest Attachment Elements)	-	3000	-
5.5(Static Strength Test for Controlled-descent Attachment Elements)	-	3000	-
5.6(Static Strength Test for Confined-space Access Attachment Elements)	-	0	-
4.1(General)	-	3000	-
4.2(Classification)	-	500	-
4.3(Design and Construction)	-	500	-
4.4(Corrosion Resistance)	-	0	-
4.5(Buckle Uncoupling and slippage)	-	0	-
4.5(Buckle Uncoupling and slippage)	-	0	-
4.6(Static Strength)	-	0	-
4.7(Dynamic Performance)	-	0	-
4.8(Static Suspension Test)	-	0	-
4.9(Static Suspension Angle test)	-	0	-
5.1.1(Torso test mass for the Static test)	-	0	-
5.1.2(Torso test mass for the Static test)	-	0	-
5.1.3(Test Layard)	-	0	-
5.1.4(Test Structure)	-	0	-
5.1.5(Static strength test apparatus)	-	0	-
5.1.6(Quick-release Device)	-	0	-
5.1.7(Test Yoke)	-	0	-
5.1.8(Force-measuring instrumentation)	-	0	-
5.2(Force-measuring instrumentation)	-	0	-
5.2(Corrosion Test)	-	0	-
5.3(Buckle Shake Test)	-	0	-
5.4(Static strength test for fall-arrest attachment elements)	-	0	-
5.5(Static strength test for controlled-descent attachment elements)	-	0	-
5.6(Static strength test for confined- space access attachment elements)	-	0	-
5.7(Dynamic Performance Test)	-	0	-
5.8(Static Suspension test for fall-arrest attachment elements)	-	0	-
5.9(Static suspension angle test)	-	0	-
5.10(Flammability Resistance Test)	-	0	-
6.2(Marking)	-	500	-

15 May, 2027

-
Included w.e.f.23.07.2025

IS 869 (2020)

Specification for Ethylene Dichloride ( Third Revision )

Industrial Chemical-Ethylene Dichloride

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	500	-
3.1.1(Solubility)	-	500	-
4.1()	-	500	-
4.2(Marking)	-	500	-
3.2 Table -1, Sl no. 1(Relative density at 15°C/15°C, Annex A2)	-	2000	-
3.2 Table -1, Sl no. 2(1,2 Dichloroethane (EDC), weight percent, ASTM D 6806)	-	8500	-
3.2 Table -1, Sl no. 3(Residue on evaporation, percent by mass, Annex A3)	-	3000	-
3.2 Table -1, Sl no. 4(Acidity (as HCl), percent by mass, Annex A4)	-	3000	-
3.2 Table -1, Sl no. 5(Colour, Annex A6)	-	3000	-
3.2 Table -1, Sl no. 6(Moisture content, percent by mass, Annex A5)	-	3000	-
3.1(Description)	-	0	-
3.1.1(Solubility)	-	0	-
4.1()	-	0	-
4.2(Marking)	-	0	-
3.2 Table -1, Sl no. 1(Relative density at 15°C/15°C, Annex A2)	-	0	-
3.2 Table -1, Sl no. 2(1,2 Dichloroethane (EDC), weight percent, ASTM D 6806)	-	0	-
3.2 Table -1, Sl no. 3(Residue on evaporation, percent by mass, Annex A3)	-	0	-
3.2 Table -1, Sl no. 4(Acidity (as HCl), percent by mass, Annex A4)	-	0	-
3.2 Table -1, Sl no. 5(Colour, Annex A6)	-	0	-
3.2 Table -1, Sl no. 6(Moisture content, percent by mass, Annex A5)	-	0	-

15 May, 2027

-
Included w.e.f 30.06.2025

IS 12029 (2023)

Acid Oil - Specification (first revision of IS 12029)

Industrial Fine chemical-Acid Oil

13800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Iodine Value)	-	800	-
4.2 Table 1 (i)(Total Fatty Matter (TFM) - IS 286 : 2018)	-	2000	-
4.2 Table 1 (ii)(Moisture and volatile matter - IS 286 : 2018)	-	2000	-
4.2 Table 1 (iii)(Free fatty Acid - IS 548 (Part 1/Sec 2) : 2021)	-	2000	-
4.2 Table 1 (iv)(Free Mineral Acid ( As H₂SO₄) - IS 12029:2023)	-	1000	-
4.2 Table 1 (v)(Unsaponifiable matter - IS 548 (Part 1/Sec 2) : 2021)	-	1000	-
4.2 Table 1 (vi)(Oxidized Fatty Acid - IS 12029:2023)	-	2000	-
4.2 Table 1 (vii)(Iron - IS 12029:2023)	-	2000	-
4.2 Table 1 (viii)(Ash - IS 12029:2023)	-	1000	-
4.1(Iodine Value)	-	0	-
4.2 Table 1 (i)(Total Fatty Matter (TFM) - IS 286 : 2018)	-	0	-
4.2 Table 1 (ii)(Moisture and volatile matter - IS 286 : 2018)	-	0	-
4.2 Table 1 (iii)(Free fatty Acid - IS 548 (Part 1/Sec 2) : 2021)	-	0	-
4.2 Table 1 (iv)(Free Mineral Acid ( As H₂SO₄) - IS 12029:2023)	-	0	-
4.2 Table 1 (v)(Unsaponifiable matter - IS 548 (Part 1/Sec 2) : 2021)	-	0	-
4.2 Table 1 (vi)(Oxidized Fatty Acid - IS 12029:2023)	-	0	-
4.2 Table 1 (vii)(Iron - IS 12029:2023)	-	0	-
4.2 Table 1 (viii)(Ash - IS 12029:2023)	-	0	-

15 May, 2027

-
Included w.e.f 30.06.2025

IS 10931 (2023)

Lauric Acid - Specification (first revision of IS 10931)

All type

15800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description)	-	300	-
4.2 Table 1 (i)(Moisture)	-	500	-
4.2 Table 1 (ii)(Saponification value)	-	1000	-
4.2 Table 1 (iii)(Acid value differ from Saponification value)	-	1000	-
4.2 Table 1 (iv)(Iodine value)	-	3000	-
4.2 Table 1 (v)(Unsaponifiable matter)	-	2000	-
4.2 Table 1 (vi)(Titre)	-	3000	-
4.2 Table 1 (vii)(Colour, 51/4 inch cell, Y + 5R)	-	1000	-
4.3 Table 2 (i)(C8:0 + C10 : 0)	-	4000	-
4.3 Table 2 (ii)(C12 : 0)	-	0	Combined test price for cl.4.3 is 4000/-.
4.3 Table 2 (i)(C14 : 0 + C16 : 0)	-	0	Combined test price for cl.4.3 is 4000/-.
4.3 Table 3 (i)(C8 : 0 + C10 : 0)	-	0	Combined test price for cl.4.3 is 4000/-.
4.3 Table 3 (ii)(C12 : 0)	-	0	Combined test price for cl.4.3 is 4000/-.
4.3 Table 3 (iii)(C14 : 0)	-	0	Combined test price for cl.4.3 is 4000/-.
4.3 Table 2 (iv)(C16 : 0)	-	0	Combined test price for cl.4.3 is 4000/-.
4.3 Table 2 (v)(Others)	-	0	Combined test price for cl.4.3 is 4000/-.
4.1(Description)	-	0	-
4.2 Table 1 (i)(Moisture)	-	0	-
4.2 Table 1 (ii)(Saponification value)	-	0	-
4.2 Table 1 (iii)(Acid value differ from Saponification value)	-	0	-
4.2 Table 1 (iv)(Iodine value)	-	0	-
4.2 Table 1 (v)(Unsaponifiable matter)	-	0	-
4.2 Table 1 (vi)(Titre)	-	0	-
4.2 Table 1 (vii)(Colour, 51/4 inch cell, Y + 5R)	-	0	-
4.3 Table 2 (i)(C8:0 + C10 : 0)	-	0	-
4.3 Table 2 (ii)(C12 : 0)	-	0	-
4.3 Table 2 (i)(C14 : 0 + C16 : 0)	-	0	-
4.3 Table 3 (i)(C8 : 0 + C10 : 0)	-	0	-
4.3 Table 3 (ii)(C12 : 0)	-	0	-
4.3 Table 3 (iii)(C14 : 0)	-	0	-
4.3 Table 2 (iv)(C16 : 0)	-	0	-
4.3 Table 2 (v)(Others)	-	0	-
4.1(Description)	-	0	-
4.2 Table 1 (i)(Moisture)	-	0	-
4.2 Table 1 (ii)(Saponification value)	-	0	-
4.2 Table 1 (iii)(Acid value differ from Saponification value)	-	0	-
4.2 Table 1 (iv)(Iodine value)	-	0	-
4.2 Table 1 (v)(Unsaponifiable matter)	-	0	-
4.2 Table 1 (vi)(Titre)	-	0	-
4.2 Table 1 (vii)(Colour, 51/4 inch cell, Y + 5R)	-	0	-
4.3 Table 2 (i)(C8:0 + C10 : 0)	-	0	-
4.3 Table 2 (ii)(C12 : 0)	-	0	-
4.3 Table 2 (i)(C14 : 0 + C16 : 0)	-	0	-
4.3 Table 3 (i)(C8 : 0 + C10 : 0)	-	0	-
4.3 Table 3 (ii)(C12 : 0)	-	0	-
4.3 Table 3 (iii)(C14 : 0)	-	0	-
4.3 Table 2 (iv)(C16 : 0)	-	0	-
4.3 Table 2 (v)(Others)	-	0	-

15 May, 2027

-
Included w.e.f 09.07.2025

IS 18340 (2023)

Vinyl Sulphone - Specification

Vinyl Sulphone

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1(Description)	-	250	-
Cl-3.2, Table-1 (i)(Assay (by nitrite value), percent by mass (on dry basis), Min)	-	3000	-
Cl-3.2, Table-1 (i)(Assay (by HPLC1)), percent area (on dry basis),Min)	-	6000	-
Cl-3.2, Table-1 (ii)(Hydrolysis value, percent by mass (on 100 percent basis), Min)	-	3000	-
Cl-3.2, Table-1 (iii)(Matter insoluble in sodium carbonate solution percent by mass, Max)	-	4000	-
Cl-3.2, Table-1 (iv)(4-Chloroaniline content, percent by mass (on 100 percent basis), Max)	-	4000	-
Cl-4.2(Marking)	-	250	-
Cl-3.1(Description)	-	0	-
Cl-3.2, Table-1 (i)(Assay (by nitrite value), percent by mass (on dry basis), Min)	-	0	-
Cl-3.2, Table-1 (i)(Assay (by HPLC1)), percent area (on dry basis),Min)	-	0	-
Cl-3.2, Table-1 (ii)(Hydrolysis value, percent by mass (on 100 percent basis), Min)	-	0	-
Cl-3.2, Table-1 (iii)(Matter insoluble in sodium carbonate solution percent by mass, Max)	-	0	-
Cl-3.2, Table-1 (iv)(4-Chloroaniline content, percent by mass (on 100 percent basis), Max)	-	0	-
Cl-4.2(Marking)	-	0	-

15 May, 2027

-
Included w.e.f 30.06.2025

IS 15907 (2010)

Agro textiles – High density polyethylene (HDPE) woven beds for vermiculture – Specification

All type

80500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Cord Beading - IS 15907)	-	400	-
5.1(MANUFACTURE- IS 15907)	-	800	-
5.2.1(Lamination- IS 15907)	-	1200	-
5.2.1(Thickness of coating film- method A of IS 13162 (Part 3))	-	200	-
5.2.1(Lamination- IS 15907)	-	0	-
5.2.2(Lamination- IS 15907)	-	0	-
5.2.2(Lamination- IS 15907)	-	0	-
5.2.2(coating thickness of the sandwich lamination- method A of IS 13162 (Part 3))	-	600	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(The width of the hem - IS 15907)	-	300	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.1(Construction- IS 15907)	-	200	-
5.3.2(Construction- IS 15907)	-	200	-
5.3.2(Construction- IS 15907)	-	200	-
5.3.2(Construction- IS 15907)	-	200	-
5.3.2(Finished width of pocket - IS 15907)	-	200	-
5.3.2(Construction- IS 15907)	-	200	-
5.4(Bonding- IS 15907)	-	500	-
6- Table 1- SL.No (i)(Mass)	-	500	-
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,warp - IS 1969 )	-	800	-
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,weft - IS 1969 )	-	0	-
6- Table 1- SL.No (iii)(Elongation at break of fabric- IS 1969)	-	0	-
6- Table 1- SL.No (iv)(Retention of breaking strength after UV exposure, - Annex B of IS 15907 and IS 1969)	-	17950	-
6- Table 1- SL.No (v)(Welded seam strength before UV exposure- IS 1969)	-	950	-
6- Table 1- SL.No (vi)(Welded seam strength after UV exposure- Annex B of IS 15907 and IS 1969)	-	17950	-
6- Table 1- SL.No (vii)(Tear strength, Warp - Method A2 of IS 7016 (Part 3))	-	400	-
6- Table 1- SL.No (vii)(Tear strength, Weft - Method A2 of IS 7016 (Part 3))	-	400	-
6- Table 1- SL.No (ix)(Environmental stress cracking test - Annex D of IS 15907)	-	1000	-
6- Table 1- SL.No (x)(Resistance to chemicals, change in the mass - Annex E of IS 15907)	-	500	-
6- Table 1- SL.No (xi)(Colour fastness to artificial light -IS 2454)	-	1000	-
6- Table 1- SL.No (xii)(Bursting pressure-IS 1966)	-	800	-
6.1(Length -IS 15907)	-	200	-
6.1(Width - IS 15907)	-	200	-
6.1(Height - IS 15907)	-	200	-
6.2(Water Proofness,IS 7941)	-	300	-
6.2(Water Proofness, IS 7940)	-	9240	-
4.1(Identification)	-	400	-
4.1(Linear Density)	-	400	-
4.1(Width)	-	200	-
6- Table 1- SL.No (viii)(Puncture strength - Annex C of IS 15907)	-	1200	-

15 May, 2027

-
Included w.e.f 10.07.2025

IS 15351 (2015)

Agro textiles – Laminated high density polyethylene (HDPE) woven geomembrane for water proof lining – Specification (second revision)

Type-I/II/III/IV

210000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(HDPE Tapes)	-	1050	-
3.2(HDPE Fabric)	-	1050	-
5(MANUFACTURE)	-	0	-
5.1(Lamination)	-	0	-
5.2(Panel Width)	-	0	-
5.3(Joints/Seams)	-	0	-
5.1.1 and 6.2(Thickness, mm- IS 7016: Part 1)	-	250	-
5.1.1 and 6.2(Mass, g/sq m)	-	250	-
5.1.1 and 6.2(Dimensions, mm- Annexure A of IS 11652)	-	250	-
5.1.1 and 6.2(Length)	-	0	-
5.1.1 and 6.2(Width)	-	0	-
5.1.1 and 6.2(Carbon black content, Percent- IS 2530)	-	925	-
5.1.1 and 6.2(Breaking Load on 20 cm X 10 cm Strip, Min )	-	1100	-
5.1.1 and 6.2(Before UV exposure IS 13162 (Part 5)	-	0	-
5.1.1 and 6.2(Strain at Maximum load, Percent-IS 13162 (Part 5)	-	1100	-
Table-1(Breaking load on 20 × 10 cm strip, N, Min after)	-	1100	-
5.1.1 and 6.2( U.V exposure of 1000 h for warp and weft)	-	96738	-
5.1.1 and 6.2(Impact failure load, at 1524 mm drop,)	-	1100	-
5.1.1 and 6.2( Min, gram force at 50 percent failure-Annex C)	-	1100	-
5.1.1 and 6.2(Tear resistance, N, Min-Method A1 of IS 7016 (Part 3))	-	1100	-
5.1.1 and 6.2(Puncture resistance, N, Min-Annex D)	-	1100	-
5.1.1 and 6.2(Bursting strength (Ball burst),N/cm², Min-)	-	1000	-
5.1.1 and 6.2(IS 7016 (Part 6))	-	0	-
5.1.1 and 6.2(Seam strength before UV exposure (N/mm), Min-IS 15060)	-	1000	-
Table-1(Seam strength after UV exposure N/mm, Min-Annex B and IS 15060)	-	1000	-
5.1.1 and 6.2(Hydrostatic resistance-Annex E)	-	1000	-
Table-1(Hydrostatic resistance after UV exposure of 1000 h -Annex B and Annex E)	-	96737	-
5.1.1 and 6.2(Ash content, percent, Max-Annex F)	-	950	-

15 May, 2027

-
Included w.e.f 10.07.2025

IS 8637 (2020)

H Acid ? Specification ( Second Revision )

Industrial Chemical-H Acid

25500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	500	-
3.2-Table 1-(i)(Purity (by nitrite value))	-	4000	-
3.2-Table 1-(ii)(Difference between nitrite value and coupling value)	-	3000	-
3.2-Table 1-(iii)(Matter insoluble in sodium carbonate solution)	-	4000	-
3.2-Table 1-(iv)(Purity (by HPCL))	-	5000	-
3.2-Table 1-(v)(Chromotropic acid content,)	-	5000	-
3.2-Table 1-(vi)(Koch’s acid content)	-	3500	-
4.1(Packing )	-	250	-
4.2(Marking)	-	250	-
3.1(Description)	-	0	-
3.2-Table 1-(i)(Purity (by nitrite value))	-	0	-
3.2-Table 1-(ii)(Difference between nitrite value and coupling value)	-	0	-
3.2-Table 1-(iii)(Matter insoluble in sodium carbonate solution)	-	0	-
3.2-Table 1-(iv)(Purity (by HPCL))	-	0	-
3.2-Table 1-(v)(Chromotropic acid content,)	-	0	-
3.2-Table 1-(vi)(Koch’s acid content)	-	0	-
4.1(Packing )	-	0	-
4.2(Marking)	-	0	-
3.1(Description)	-	0	-
3.2-Table 1-(i)(Purity (by nitrite value))	-	0	-
3.2-Table 1-(ii)(Difference between nitrite value and coupling value)	-	0	-
3.2-Table 1-(iii)(Matter insoluble in sodium carbonate solution)	-	0	-
3.2-Table 1-(iv)(Purity (by HPCL))	-	0	-
3.2-Table 1-(v)(Chromotropic acid content,)	-	0	-
3.2-Table 1-(vi)(Koch’s acid content)	-	0	-
4.1(Packing )	-	0	-
4.2(Marking)	-	0	-

15 May, 2027

-
Included w.e.f.18.06.2025

IS 5557 : Part 1 (2024)

All Rubber Gum Boots and Ankle Boots Part 1 Safety and Protective

Footwear

60500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Design)	-	500	-
6(Sizes and Fittines)	-	500	-
7(Consturction)	-	800	-
8.1(Lining Material)	-	200	-
8.2, Table-1 (i)(Width, mm, Min)	-	300	-
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	800	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	1500	-
8.4(Use of Rubber material)	-	0	-
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	500	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	1000	-
8.5(Upper material)	-	0	-
8.5.1(Tensile Strength of upper)	-	1000	-
8.5.2(Thickness)	-	400	-
8.5.3(Flexing Resistance)	-	1000	-
8.5.4(Abrasion Resistance)	-	1000	-
8.6.1(Thickness of Outsole)	-	500	-
8.6.2(Tear Strength)	-	1000	-
8.6.3(Abrasion Resistance of Outsole)	-	1000	-
8.6.4(Flexing Resistance)	-	1000	-
8.6.5(Inter layer Bond Strength of outsole)	-	1000	-
Cl-8.7(Insocks material)	-	0	-
8.7.1(Thickness of Insocks)	-	500	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	700	-
Cl-8.8.1(Outsole/Heel)	-	800	-
Cl-8.9(Leak Proof Test)	-	1000	-
8.10(Height of Upper)	-	300	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	800	-
Cl-8.12(Upper Outsole Bond Strength)	-	700	-
Cl-8.13(Internal Length of Toe Cap)	-	800	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	500	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	500	-
8.16(Banned Chemicals)	-	30000	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	3000	-
8.17(Steel Floor with Glycerine)	-	0	Test price for cl. 8.17 is 3000/-.
8.18(Corrosion Resistant Test for Toe Caps)	-	500	-
9.1(Penetration Resistance)	-	1000	-
9.2(Antistatic Footwear)	-	1000	-
9.3(Flame Resistance Property)	-	1000	-
9.4(Electrical Resistance)	-	1000	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	1000	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	0	Test price for cl. 9.5 Resistance to Acid and Alkali is 1000/-.
9.6(Resistance to Fuel Oil)	-	1000	-
11.2(Marking)	-	500	-
Cl-5(Design)	-	0	-
6(Sizes and Fittines)	-	0	-
7(Consturction)	-	0	-
8.1(Lining Material)	-	0	-
8.2, Table-1 (i)(Width, mm, Min)	-	0	-
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	0	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	0	-
8.4(Use of Rubber material)	-	0	-
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	0	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	0	-
8.5(Upper material)	-	0	-
8.5.1(Tensile Strength of upper)	-	0	-
8.5.2(Thickness)	-	0	-
8.5.3(Flexing Resistance)	-	0	-
8.5.4(Abrasion Resistance)	-	0	-
8.6.1(Thickness of Outsole)	-	0	-
8.6.2(Tear Strength)	-	0	-
8.6.3(Abrasion Resistance of Outsole)	-	0	-
8.6.4(Flexing Resistance)	-	0	-
8.6.5(Inter layer Bond Strength of outsole)	-	0	-
Cl-8.7(Insocks material)	-	0	-
8.7.1(Thickness of Insocks)	-	0	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	0	-
Cl-8.8.1(Outsole/Heel)	-	0	-
Cl-8.9(Leak Proof Test)	-	0	-
8.10(Height of Upper)	-	0	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	0	-
Cl-8.12(Upper Outsole Bond Strength)	-	0	-
Cl-8.13(Internal Length of Toe Cap)	-	0	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	0	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	0	-
8.16(Banned Chemicals)	-	0	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	0	-
8.17(Steel Floor with Glycerine)	-	0	-
8.18(Corrosion Resistant Test for Toe Caps)	-	0	-
9.1(Penetration Resistance)	-	0	-
9.2(Antistatic Footwear)	-	0	-
9.3(Flame Resistance Property)	-	0	-
9.4(Electrical Resistance)	-	0	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	0	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	0	-
9.6(Resistance to Fuel Oil)	-	0	-
11.2(Marking)	-	0	-
Cl-5(Design)	-	0	-
6(Sizes and Fittines)	-	0	-
7(Consturction)	-	0	-
8.1(Lining Material)	-	0	-
8.2, Table-1 (i)(Width, mm, Min)	-	0	`
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	0	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	0	`
8.4(Use of Rubber material)	-	0	`
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	0	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	0	-
8.5(Upper material)	-	0	-
8.5.1(Tensile Strength of upper)	-	0	-
8.5.2(Thickness)	-	0	-
8.5.3(Flexing Resistance)	-	0	-
8.5.4(Abrasion Resistance)	-	0	-
8.6.1(Thickness of Outsole)	-	0	-
8.6.2(Tear Strength)	-	0	-
8.6.3(Abrasion Resistance of Outsole)	-	0	-
8.6.4(Flexing Resistance)	-	0	-
8.6.5(Inter layer Bond Strength of outsole)	-	0	-
Cl-8.7(Insocks material)	-	0	-
8.7.1(Thickness of Insocks)	-	0	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	0	-
Cl-8.8.1(Outsole/Heel)	-	0	-
Cl-8.9(Leak Proof Test)	-	0	-
8.10(Height of Upper)	-	0	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	0	-
Cl-8.12(Upper Outsole Bond Strength)	-	0	-
Cl-8.13(Internal Length of Toe Cap)	-	0	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	0	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	0	-
8.16(Banned Chemicals)	-	0	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	0	-
8.17(Steel Floor with Glycerine)	-	0	-
8.18(Corrosion Resistant Test for Toe Caps)	-	0	-
9.1(Penetration Resistance)	-	0	-
9.2(Antistatic Footwear)	-	0	-
9.3(Flame Resistance Property)	-	0	-
9.4(Electrical Resistance)	-	0	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	0	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	0	-
9.6(Resistance to Fuel Oil)	-	0	-
11.2(Marking)	-	0	-
Cl-5(Design)	-	0	-
6(Sizes and Fittines)	-	0	``
7(Consturction)	-	0	-
8.1(Lining Material)	-	0	-
8.2, Table-1 (i)(Width, mm, Min)	-	0	-
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	0	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	0	-
8.4(Use of Rubber material)	-	0	-
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	0	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	0	-
8.5(Upper material)	-	0	-
8.5.1(Tensile Strength of upper)	-	0	-
8.5.2(Thickness)	-	0	-
8.5.3(Flexing Resistance)	-	0	-
8.5.4(Abrasion Resistance)	-	0	-
8.6.1(Thickness of Outsole)	-	0	-
8.6.2(Tear Strength)	-	0	-
8.6.3(Abrasion Resistance of Outsole)	-	0	-
8.6.4(Flexing Resistance)	-	0	-
8.6.5(Inter layer Bond Strength of outsole)	-	0	-
Cl-8.7(Insocks material)	-	0	-
8.7.1(Thickness of Insocks)	-	0	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	0	-
Cl-8.8.1(Outsole/Heel)	-	0	-
Cl-8.9(Leak Proof Test)	-	0	-
8.10(Height of Upper)	-	0	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	0	-
Cl-8.12(Upper Outsole Bond Strength)	-	0	-
Cl-8.13(Internal Length of Toe Cap)	-	0	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	0	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	0	-
8.16(Banned Chemicals)	-	0	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	0	-
8.17(Steel Floor with Glycerine)	-	0	-
8.18(Corrosion Resistant Test for Toe Caps)	-	0	-
9.1(Penetration Resistance)	-	0	-
9.2(Antistatic Footwear)	-	0	-
9.3(Flame Resistance Property)	-	0	-
9.4(Electrical Resistance)	-	0	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	0	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	0	-
9.6(Resistance to Fuel Oil)	-	0	-
11.2(Marking)	-	0	-

15 May, 2027

-
Included w.e.f 18.08.2025

IS 14707 (1999)

Methyl acrylate - Specification

Methyl acrylate

26500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Packing)	-	26500	-
4.2(Marking)	-	26500	-
3 - Table -1, Sl no. 1(Assay, percent by mass, Min, Annex A)	-	26500	-
3 - Table -1, Sl no. 2(Acidity (as acrylic acid),percent by mass, Max, Annex B)	-	26500	-
3 - Table -1, Sl no. 3(Colour, Pt-Co scale, Max, IS 8768)	-	26500	-
3 - Table -1, Sl no. 4(Water, percent by mass,Max, 2362)	-	26500	-
3 - Table -1, Sl no. 5(" Inhibitors (as methyl etherhydroquinone), ppm Max , Annex C ")	-	26500	-
4.1(Packing)	-	0	-
4.2(Marking)	-	0	-
3 - Table -1, Sl no. 1(Assay, percent by mass, Min, Annex A)	-	0	-
3 - Table -1, Sl no. 2(Acidity (as acrylic acid),percent by mass, Max, Annex B)	-	0	-
3 - Table -1, Sl no. 3(Colour, Pt-Co scale, Max, IS 8768)	-	0	-
3 - Table -1, Sl no. 4(Water, percent by mass,Max, 2362)	-	0	-
3 - Table -1, Sl no. 5(" Inhibitors (as methyl etherhydroquinone), ppm Max , Annex C ")	-	0	-

15 May, 2027

-
Included w.e.f.18.06.2025

IS 16112 (2013)

Beta picoline - Specification

Beta picoline

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	500	-
3.2(Solubility)	-	500	-
4.1(Packing)	-	250	-
4.2(Marking)	-	250	-
3.3 - Table -1, Sl no. 1(Beta picoline content,percent by mass, Min, Annex A)	-	2500	-
3.3 - Table -1, Sl no. 2(2-Ethyl pyridine content,percent by mass, Max, Annex A)	-	2500	-
3.3 - Table -1, Sl no. 3(Alpha picoline content,percent by mass, Max,Annex A)	-	2500	-
3.3 - Table -1, Sl no. 4(Gamma picoline content,percent by mass, Max, Annex A)	-	2500	-
3.3 - Table -1, Sl no. 5(Other unknown impurities,percent by mass, Max, Annex A)	-	2500	-
3.3 - Table -1, Sl no. 6(Moisture content,percent by mass, Max, Annex B)	-	2500	-
3.1(Description)	-	0	-
3.2(Solubility)	-	0	-
4.1(Packing)	-	0	-
4.2(Marking)	-	0	-
3.3 - Table -1, Sl no. 1(Beta picoline content,percent by mass, Min, Annex A)	-	0	-
3.3 - Table -1, Sl no. 2(2-Ethyl pyridine content,percent by mass, Max, Annex A)	-	0	-
3.3 - Table -1, Sl no. 3(Alpha picoline content,percent by mass, Max,Annex A)	-	0	-
3.3 - Table -1, Sl no. 4(Gamma picoline content,percent by mass, Max, Annex A)	-	0	-
3.3 - Table -1, Sl no. 5(Other unknown impurities,percent by mass, Max, Annex A)	-	0	-
3.3 - Table -1, Sl no. 6(Moisture content,percent by mass, Max, Annex B)	-	0	-
3.1(Description)	-	0	-
3.2(Solubility)	-	0	-
4.1(Packing)	-	0	-
4.2(Marking)	-	0	-
3.3 - Table -1, Sl no. 1(Beta picoline content,percent by mass, Min, Annex A)	-	0	-
3.3 - Table -1, Sl no. 2(2-Ethyl pyridine content,percent by mass, Max, Annex A)	-	0	-
3.3 - Table -1, Sl no. 3(Alpha picoline content,percent by mass, Max,Annex A)	-	0	-
3.3 - Table -1, Sl no. 4(Gamma picoline content,percent by mass, Max, Annex A)	-	0	-
3.3 - Table -1, Sl no. 5(Other unknown impurities,percent by mass, Max, Annex A)	-	0	-
3.3 - Table -1, Sl no. 6(Moisture content,percent by mass, Max, Annex B)	-	0	-

15 May, 2027

-
Included .w.e.f.18.06.2025

IS 16113 (2013)

Gamma picoline - Specification

Industrial Chemical-Gamma picoline

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	500	-
3.2(Solubility)	-	500	-
4.1(Packing)	-	250	-
4.2(Marking)	-	250	-
3.3 - Table -1, Sl no. 1(Gamma picoline content,percent by mass, Min, Annex A)	-	2500	-
3.3 - Table -1, Sl no. 2(2-Ethyl pyridine content,percent by mass, Max, Annex A)	-	2000	-
3.3 - Table -1, Sl no. 3(Alpha picoline content,percent by mass, Max,Annex A)	-	2000	-
3.3 - Table -1, Sl no. 4(Beta picoline content,percent by mass, Max, Annex A)	-	2000	-
3.3 - Table -1, Sl no. 5(2,6-Lutidine content,percent by mass, Max,Annex A)	-	2500	-
3.3 - Table -1, Sl no. 6(Other unknown impurities,percent by mass, Max, Annex A)	-	2000	-
3.3 - Table -1, Sl no. 7(Moisture content,percent by mass, Max, Annex B)	-	2000	-

15 May, 2027

-
Included w.e.f.18.06.2025

IS 12345 (2024)

Vinyl Acetate Monomer â Specification (First Revision)

VINYLY ACETATE MONOMER

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1("The material shall be clear, colourless liquid, free from any suspended matter")	-	500	-
3.1 Table 1(i)("Acidity (as acetic acid), percent by mass")	-	2000	-
3.1 Table 1(ii)("Vinyl acetate content (as ester), percent by mass")	-	4000	-
3.1 Table 1(iii)("Aldehyde (as acetaldehyde), percent by mass")	-	2500	-
3.1 Table 1(iv)(Moisture, percent by mass)	-	2000	-
3.1 Table 1(v)(Distillation range at 760 mm of Hg)	-	2000	-
3.1 Table 1(vi)(Colour, Pt-Co)	-	1500	-
3.1 Table 1(vii)(Specific gravity, 20 °C/20 °C)	-	1000	-
3.1 Table 1(viii, a)(Hydroquinone)	-	2000	-
3.1 Table 1(viii, b)(Diphenylamine)	-	2000	-
3.1 Table 1(ix)(Polymer content)	-	2000	-
4.1(Packing)	-	500	-
4.2(Marking)	-	500	-
3.1("The material shall be clear, colourless liquid, free from any suspended matter")	-	0	-
3.1 Table 1(i)("Acidity (as acetic acid), percent by mass")	-	0	-
3.1 Table 1(ii)("Vinyl acetate content (as ester), percent by mass")	-	0	-
3.1 Table 1(iii)("Aldehyde (as acetaldehyde), percent by mass")	-	0	-
3.1 Table 1(iv)(Moisture, percent by mass)	-	0	-
3.1 Table 1(v)(Distillation range at 760 mm of Hg)	-	0	-
3.1 Table 1(vi)(Colour, Pt-Co)	-	0	-
3.1 Table 1(vii)(Specific gravity, 20 °C/20 °C)	-	0	-
3.1 Table 1(viii, a)(Hydroquinone)	-	0	-
3.1 Table 1(viii, b)(Diphenylamine)	-	0	-
3.1 Table 1(ix)(Polymer content)	-	0	-
4.1(Packing)	-	0	-
4.2(Marking)	-	0	-
3.1("The material shall be clear, colourless liquid, free from any suspended matter")	-	0	-
3.1 Table 1(i)("Acidity (as acetic acid), percent by mass")	-	0	-
3.1 Table 1(ii)("Vinyl acetate content (as ester), percent by mass")	-	0	-
3.1 Table 1(iii)("Aldehyde (as acetaldehyde), percent by mass")	-	0	-
3.1 Table 1(iv)(Moisture, percent by mass)	-	0	-
3.1 Table 1(v)(Distillation range at 760 mm of Hg)	-	0	-
3.1 Table 1(vi)(Colour, Pt-Co)	-	0	-
3.1 Table 1(vii)(Specific gravity, 20 °C/20 °C)	-	0	-
3.1 Table 1(viii, a)(Hydroquinone)	-	0	-
3.1 Table 1(viii, b)(Diphenylamine)	-	0	-
3.1 Table 1(ix)(Polymer content)	-	0	-
4.1(Packing)	-	0	-
4.2(Marking)	-	0	-

15 May, 2027

-
Included w.e.f.18.06.2025

IS 16948 (2018)

Medical textile – Permeable nonwoven surgical adhesive tape – Specification

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 and 4.2(Workmanship and finish)	-	500	-
5.1 - Table 1 -(i)(Weight of backing material)	-	1250	-
5.1 - Table 1 -(ii)(Weight of adhesive mass)	-	1250	-
5.1 - Table 1 -(iii)(Water vapour permeability)	-	1000	-
5.1 - Table 1 -(iv)(Adhesiveness)	-	2000	-
5.1 - Table 1 -(v)(Width of the tape)	-	500	-
6(Marking)	-	300	-
5.1 - Table 1 -(v)(Width of the tape)	-	0	-
5.1 - Table 1 -(vi)(Perforations)	-	500	-
6(Marking)	-	0	-
8(Packing)	-	200	-
4(Workmanship and finish)	-	0	-
5- Table-1- i)(Weight of backing material)	-	0	-
5- Table-1- ii)(Weight of adhesive mass)	-	0	-
5- Table-1- iii)(Water vapour permeability)	-	0	-
5- Table-1- iv)(Adhesiveness)	-	0	-
5- Table-1- v)(Width of the tape)	-	0	-
5- Table-1- vi)(Width of the tape)	-	0	-
6(Marking)	-	0	-
8(Packing)	-	0	-

15 May, 2027

-
Included w.e.f.23.06.2025

IS 8698 (2022)

expanded vinyl coated fabrics-Specification Second Revision

Type A and Type B

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7.1(Description)	-	500	-
Cl-7.2(Base Fabric)	-	500	-
Cl-7.3(Appearance)	-	500	-
Cl-7.4(Colour, Grain and Finish)	-	500	-
Cl-7.5(Coating)	-	500	-
Cl-7.6(Resistance to Heat and Loss of Mass on Heating)	-	1000	-
Cl-7.7(Resistance to Cold)	-	1000	-
Cl-7.8(Colour Fastness to Dry and Wet Rubbing)	-	500	-
Cl-7.9(Colour Fastness to Light)	-	500	-
Cl-7.10(Gelling Test)	-	500	-
Cl-7.11(Adhesion of Print)	-	500	-
Cl-7.12(Flame Resistance)	-	1000	-
Cl-7.13(Adhesion of Coating)	-	1000	-
Cl-7.14(Blocking Resistance)	-	1000	-
Cl-7.15(Resistance to Penetration of Water)	-	1000	-
Cl-7.16("Elongation and Elastic Recovery for a Constant Load")	-	1000	-
Cl-7.17, 8.1 Table-1 (i)(Usable width, Min, cm)	-	500	-
Cl-7.17, 8.1 Table-1 (ii)(Mass of finished fabric, Min, g/m2)	-	500	-
Cl-7.17, 8.1 Table-1 (iii)(a) Longitudinal direction)	-	1000	-
Cl-7.17, 8.1 Table-1 (iii)(b) Transverse direction)	-	0	Breaking strength test price is 1000/-.
Cl-7.17, 8.1 Table-1 (iv)(Tear strength)	-	1000	-
Cl-7.17, 8.1 Table-1 (v)(Resistance to damage by flexing)	-	500	-
Cl-8.2(Test Specimens)	-	300	-
Cl-9.2(Marking)	-	200	-
Cl-7.1(Description)	-	0	-
Cl-7.2(Base Fabric)	-	0	-
Cl-7.3(Appearance)	-	0	-
Cl-7.4(Colour, Grain and Finish)	-	0	-
Cl-7.5(Coating)	-	0	-
Cl-7.6(Resistance to Heat and Loss of Mass on Heating)	-	0	-
Cl-7.7(Resistance to Cold)	-	0	-
Cl-7.8(Colour Fastness to Dry and Wet Rubbing)	-	0	-
Cl-7.9(Colour Fastness to Light)	-	0	-
Cl-7.10(Gelling Test)	-	0	-
Cl-7.11(Adhesion of Print)	-	0	-
Cl-7.12(Flame Resistance)	-	0	-
Cl-7.13(Adhesion of Coating)	-	0	-
Cl-7.14(Blocking Resistance)	-	0	-
Cl-7.15(Resistance to Penetration of Water)	-	0	-
Cl-7.16("Elongation and Elastic Recovery for a Constant Load")	-	0	-
Cl-7.17, 8.1 Table-1 (i)(Usable width, Min, cm)	-	0	-
Cl-7.17, 8.1 Table-1 (ii)(Mass of finished fabric, Min, g/m2)	-	0	-
Cl-7.17, 8.1 Table-1 (iii)(a) Longitudinal direction)	-	0	-
Cl-7.17, 8.1 Table-1 (iii)(b) Transverse direction)	-	0	-
Cl-7.17, 8.1 Table-1 (iv)(Tear strength)	-	0	-
Cl-7.17, 8.1 Table-1 (v)(Resistance to damage by flexing)	-	0	-
Cl-8.2(Test Specimens)	-	0	-
Cl-9.2(Marking)	-	0	-
Cl-7.1(Description)	-	0	-
Cl-7.2(Base Fabric)	-	0	-
Cl-7.3(Appearance)	-	0	-
Cl-7.4(Colour, Grain and Finish)	-	0	-
Cl-7.5(Coating)	-	0	-
Cl-7.6(Resistance to Heat and Loss of Mass on Heating)	-	0	-
Cl-7.7(Resistance to Cold)	-	0	-
Cl-7.8(Colour Fastness to Dry and Wet Rubbing)	-	0	-
Cl-7.9(Colour Fastness to Light)	-	0	-
Cl-7.10(Gelling Test)	-	0	-
Cl-7.11(Adhesion of Print)	-	0	-
Cl-7.12(Flame Resistance)	-	0	-
Cl-7.13(Adhesion of Coating)	-	0	-
Cl-7.14(Blocking Resistance)	-	0	-
Cl-7.15(Resistance to Penetration of Water)	-	0	-
Cl-7.16("Elongation and Elastic Recovery for a Constant Load")	-	0	-
Cl-7.17, 8.1 Table-1 (i)(Usable width, Min, cm)	-	0	-
Cl-7.17, 8.1 Table-1 (ii)(Mass of finished fabric, Min, g/m2)	-	0	-
Cl-7.17, 8.1 Table-1 (iii)(a) Longitudinal direction)	-	0	-
Cl-7.17, 8.1 Table-1 (iii)(b) Transverse direction)	-	0	-
Cl-7.17, 8.1 Table-1 (iv)(Tear strength)	-	0	-
Cl-7.17, 8.1 Table-1 (v)(Resistance to damage by flexing)	-	0	-
Cl-8.2(Test Specimens)	-	0	-
Cl-9.2(Marking)	-	0	-

15 May, 2027

-
Included w.e.f.23.06.2025

IS 8699 (1977)

Specification for pvc coated fabrics for footwear industry

Type A/Type B

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1.1 and 4.1, Table - 1 (ii)(Total Mass)	-	500	-
3.1.1 and 4.1, Table - 1 (iii)(Breaking Strength Warp direction)	-	1000	-
3.1.1 and 4.1, Table - 1 (iii)(Breaking Strength Weft direction)	-	0	-
3.1.1 and 4.1, Table - 1 (iv)("Resistance to damage by flexing Stage I ")	-	1000	-
3.1.1 and 4.1, Table - 1 (iv)("Resistance to damage by flexing Stage II ")	-	0	-
3.1.1 and 4.1, Table - 1 (v)(Thickness)	-	500	-
4.2(Appearance)	-	500	-
4.3(Colour , Grain, Embossing and finish)	-	500	-
4.4.1(Resistance to cold)	-	1000	-
4.4.2(Colour fastness to Dry and Wet Rubbing)	-	1000	-
4.4.3(Colour fastness to light)	-	1000	-
4.4.4(Resistance to heat and loss of mass of coating on heating)	-	1000	-
4.4.5(Stability at Vulcanization Temperature)	-	1000	-
4.5(Resistance to Gelling)	-	1000	-
4.5.1(Embossing on Grain)	-	500	-
4.6(Adhesion of print (for Printed PVC Coated fabrics))	-	1000	-
4.7(Adhesion of coating)	-	1000	-
3.1.1 and 4.1, Table - 1 (ii)(Total Mass)	-	0	-
3.1.1 and 4.1, Table - 1 (iii)(Breaking Strength Warp direction)	-	0	-
3.1.1 and 4.1, Table - 1 (iii)(Breaking Strength Weft direction)	-	0	-
3.1.1 and 4.1, Table - 1 (iv)("Resistance to damage by flexing Stage I ")	-	0	-
3.1.1 and 4.1, Table - 1 (iv)("Resistance to damage by flexing Stage II ")	-	0	-
3.1.1 and 4.1, Table - 1 (v)(Thickness)	-	0	-
4.2(Appearance)	-	0	-
4.3(Colour , Grain, Embossing and finish)	-	0	-
4.4.1(Resistance to cold)	-	0	-
4.4.2(Colour fastness to Dry and Wet Rubbing)	-	0	-
4.4.3(Colour fastness to light)	-	0	-
4.4.4(Resistance to heat and loss of mass of coating on heating)	-	0	-
4.4.5(Stability at Vulcanization Temperature)	-	0	-
4.5(Resistance to Gelling)	-	0	-
4.5.1(Embossing on Grain)	-	0	-
4.6(Adhesion of print (for Printed PVC Coated fabrics))	-	0	-
4.7(Adhesion of coating)	-	0	-
Cl-3.1.1, & 4.1 Table-1 (i)(Usable width, cm, Min)	-	0	-

15 May, 2027

-
Included w.e.f.23.06.2025

IS 15354 : Part 1 (2023)

Single-use medical examination gloves Part 1 Specification for gloves made from rubber latex or rubber solution Second Revision

type-1/type-2

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.3(Finish)	-	500	-
Cl-5(Materials)	-	1000	-
Cl-7.1, Table-2(Size code)	-	500	-
Cl-7.1, Table-2(Width corresponding to size code (dimension w, Figure 1))	-	500	-
Cl-7.1, Table-2(Descriptive size)	-	500	-
Cl-7.1, Table-2(Width corresponding to descriptive size (dimension w, Figure 1))	-	500	-
Cl-7.1, Table-2(Minimum length (dimension l, Figure 1))	-	500	-
Cl-7.1, Table-2(Minimum thickness (at locations shown in Figure 1))	-	500	-
Cl-7.1, Table-2(Maximum thickness (at approximate centre of palm))	-	500	-
Cl-7.2(Water tightness)	-	2000	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum force at break before accelerated ageing, N)	-	750	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum elongation at break before accelerated ageing, %)	-	750	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum force at break after accelerated ageing, N)	-	500	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum elongation at break after accelerated ageing, %)	-	500	-
Cl-9(Marking)	-	500	-
Cl-4.3(Finish)	-	0	-
Cl-5(Materials)	-	0	-
Cl-7.1, Table-2(Size code)	-	0	-
Cl-7.1, Table-2(Width corresponding to size code (dimension w, Figure 1))	-	0	-
Cl-7.1, Table-2(Descriptive size)	-	0	-
Cl-7.1, Table-2(Width corresponding to descriptive size (dimension w, Figure 1))	-	0	-
Cl-7.1, Table-2(Minimum length (dimension l, Figure 1))	-	0	-
Cl-7.1, Table-2(Minimum thickness (at locations shown in Figure 1))	-	0	-
Cl-7.1, Table-2(Maximum thickness (at approximate centre of palm))	-	0	-
Cl-7.2(Water tightness)	-	0	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum force at break before accelerated ageing, N)	-	0	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum elongation at break before accelerated ageing, %)	-	0	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum force at break after accelerated ageing, N)	-	0	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum elongation at break after accelerated ageing, %)	-	0	-
Cl-9(Marking)	-	0	-
Cl-4.3(Finish)	-	0	-
Cl-5(Materials)	-	0	-
Cl-7.1, Table-2(Size code)	-	0	-
Cl-7.1, Table-2(Width corresponding to size code (dimension w, Figure 1))	-	0	-
Cl-7.1, Table-2(Descriptive size)	-	0	-
Cl-7.1, Table-2(Width corresponding to descriptive size (dimension w, Figure 1))	-	0	-
Cl-7.1, Table-2(Minimum length (dimension l, Figure 1))	-	0	-
Cl-7.1, Table-2(Minimum thickness (at locations shown in Figure 1))	-	0	-
Cl-7.1, Table-2(Maximum thickness (at approximate centre of palm))	-	0	-
Cl-7.2(Water tightness)	-	0	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum force at break before accelerated ageing, N)	-	0	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum elongation at break before accelerated ageing, %)	-	0	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum force at break after accelerated ageing, N)	-	0	-
Cl-7.3.2 & 7.3.3, Table-3(Minimum elongation at break after accelerated ageing, %)	-	0	-
Cl-9(Marking)	-	0	-

15 May, 2027

-
Included w.e.f 03.06.2025 Exclusion: Cl-7.4 (Sterility)

IS 17399 (2020)

Textiles - Polypropylene ( PP )/ High Density Polyethylene ( HDPE ) Laminated Woven Sacks for Mail Sorting, Storage, Transport and Distribution - Specification

Type-I/Type-II/Type-III

32820 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(MANUFACTURE - Raw Materials)	-	2500	-
5.2(MANUFACTURE - Fabric for PP tapes & for HDPE tapes)	-	1800	-
5.2- Table 1- i)("REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm")	-	1500	-
5.2- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	250	-
5.2- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	250	-
5.2- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	500	-
5.2- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf) a) Lengthwise b) Widthwise)	-	3000	-
5.2- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min, N2), (kgf))	-	1500	-
5.2- Table 1- vii)("REQUIREMENTS - Elongation at break of fabric, percent: a) Lengthwise b) Widthwise")	-	0	-
5.2- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	1500	-
5.3(Lamination)	-	1500	-
5.4(Sack Fabrication)	-	500	-
5.5(Capacity)	-	500	-
6.1- Table 1- i)(REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm)	-	0	-
6.1- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	0	-
6.1- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	0	-
6.1- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	0	-
6.1- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf))	-	0	-
6.1- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min)	-	0	-
6.1- Table 1- vii)(REQUIREMENTS - Elongation at break of fabric, percent a) Lengthwise b) Widthwise)	-	0	-
6.1- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	0	-
6.4(UV Resistance Test)	-	16520	-
7(PRINTING, PACKAGING AND MARKING)	-	500	-
8(ATMOSPHERIC CONDITIONS FOR SAMPLE CONDITIONING AND TESTING)	-	500	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 5.4(Sack Fabrication)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-

15 May, 2027

-
Included w.e.f.19.05.2025

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

HDPE/PP

30500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	500	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	250	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	250	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	250	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	250	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	250	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	250	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	250	-
4.1(Raw Material )	-	2000	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	1000	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	250	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	500	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	1000	-
4.4(Seam )	-	1000	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	250	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	250	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	1000	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	250	-
4.7(Valve for Filling of Sacks)	-	250	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	500	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	3000	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1500	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1500	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	1500	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	11600	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	0	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	400	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	0	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	0	-
Cl-5 Fig. 1- Table 1- Sr. no. ii(Ends per dm - Annex B 40 ± 2)	-	0	-
Cl-5 Fig. 1- Table 1-Sr. no. iii(Picks per dm-Annex B 40 ± 2)	-	0	-
Cl-5, Fig. 1- Table 1- Sr. no. i(Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm)	-	0	-
Cl-5, Fig. 1- Table 1- Sr. no. i(Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm)	-	0	-
Cl-5, Fig. 1- Table 1-Sr. no. i(Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm)	-	0	-
Cl-5, Fig. 1, Table 1(i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm)	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	-
4.1(Raw Material )	-	0	-
4.2 (Fabric)	-	0	-
4.2 (Linear Density, 900 denier)	-	0	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B e) Depth of valve (f), Min, The depth of the valve (f) shall not be less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
4.3(Sacks)	-	0	-
4.4(Seam )	-	0	-
4.4(Seam )	-	0	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(Seam)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	0	-
4.4(Seam)	-	0	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.5(Lamination )	-	0	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	0	-
4.7(Valve for Filling of Sacks)	-	0	-
4.7(There shall be a double fold at the top seam and)	-	0	-
4.7(and then stitching shall be done through six layers.)	-	0	-
4.7(The depth of the valve (f) shall not be less than 2 times the width of the valve (v) in case of gusseted sacks and)	-	0	-
4.7(and not less than 2.3 times the width of the valve (v) in case of non-gusseted sacks. )	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	-
5/5.1(The mass of bale of sacks (excluding packing materials) shall be within ± 3 percent of the mass calculated by multiplying the number of sacks with the mass of sack specified in Table 1.)	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	0	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	0	-
4.4(Seam)	-	0	`

15 May, 2027

-
Included w.e.f.19.05.2025

IS 362 (1991)

Parliament Hinges -specification

All type

13800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 (Brass parliament hinges shall have either bright or satin finish and shall be suitably protected against discoloration)	-	2000	-
Cl. 7.2 (Ref. Cl. 11.1 of IS 1868:1996)( appearance and Colour - shall be free from visible defects on the significant surface(s) when viewed from an agreed distance)	-	2000	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Aluminium shall be anodized to a bright, natural, sat or satin finish or dyed. )	-	0	Test price for cl.7 is 2000/-.
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	0	-
Cl. 7.3(Mild steel parliament hinges shall be finished bright or electro-galvanized as specified by the purchaser)	-	500	-
3(Type)	-	1000	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Size)	-	1600	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-	0	Test price for table-2-dimension test is 1600/-.
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-No. of Screw holes)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Holes for screw designation)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Size)	-	1500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-A)	-	0	Test price for table-3-dimension test is 1500/-.
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-B)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-C)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-D)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-d)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-E)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Thickness of Flap)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-No. of Screw holes)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Holes for screw designation)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Size)	-	1500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-A)	-	0	Test price for table-4-dimension test is 1500/-.
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-B)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-C)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-D)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-d)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-E)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Thickness of Flap)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-No. of Screw holes)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Holes for screw designation)	-	0	-
6.1(MANUFACTURE-General)	-	500	-
6.1(MANUFACTURE-General)	-	0	Test price for cl. 6.1-General is 500/-.
6.1(MANUFACTURE-General)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	500	-
6.2(MANUFACTURE-Knuckles)	-	0	Test price for cl. 6.2-knuckles is 500/-.
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.3(MANUFACTURE-Pins)	-	2000	-
6.3(MANUFACTURE-Pins)	-	0	Test price for cl. 6.3-pins is 2000/-.
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.4(MANUFACTURE-Screw Holes)	-	200	-
6.5(MANUFACTURE-Position of Holes)	-	800	-
6.5(MANUFACTURE-Position of Holes)	-	0	Test price for cl. 6.5-position of holes is 800/-.
6.5(MANUFACTURE-Position of Holes-minimum distance from the ends of the flap)	-	0	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the inner edge)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
7.1(FINISH)	-	500	-
7.3(FINISH)	-	500	-

15 May, 2027

-
Included w.e.f 10.07.2025

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

All type

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	200	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Copper - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Lead - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Iron - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Zinc- IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Tin - IS 4027:1967)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Phosphorous - IS 4027:1967)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Lead - IS 4027:1967)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Total impurities - IS 4027:1967)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Copper - IS 4027:1967)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Carbon - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Manganese - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Sulphur - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Phosphorous - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Silicon - IS 228 (optional))	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Tota Aluminium - IS 228 (optional))	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Copper - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Lead - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Iron - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Total impurities - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Zinc - IS 3685:1966)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Carbon - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Silicon - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Manganese - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Nickel - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Chromium - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Molybdenum - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Sulphur - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Phosphorous - IS 228)	-	0	Chemical composition testing for Flap and Pin Material is 4000/-.
3(TYPES)	-	200	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	800	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	200	-
5.2 ,Table 6(Tolerances-Tolerances on dimensions of hinges )	-	300	-
6.1(Manufacture- General)	-	200	-
6.2- Table 2,3,4,5 (Kunckles)	-	300	-
6.3(Screw Holes)	-	250	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	250	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	250	-
6.3.3 Fig-1(Position of Holes)	-	250	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	250	-
8.2(Packing -Each Package shall bear the following Particulars)	-	250	-
7(Workmanship & Finish)	-	800	-
10(Marking)	-	200	-

15 May, 2027

-
Included w.e.f 10.07.2025

First
Prev
1
2
3
4
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Sleen India Biz venture Private Limited, Agra

RAHANKALAN ROAD, PART 295, BLOCK-A KUBERPUR, 300 METER FROM RAILWAY CROSSING CHALESHAR ROAD, Agra, Uttar Pradesh, India, 282006, Agra, Agra, Uttar Pradesh, 282006

8193022228 sleen.info@gmail.com

Scope List