BIS - LIMS (Laboratory Information Management System)

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List

Reset

364 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 10238 (2001)

Fasteners - Threaded steel fasteners - Step bolts for steel structures - Specification (First Revision)

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (DIMENSIONS AND TOLERANCES)	-
8.1 (FINISH)	-
Table 3 (x) (Vickers hardness)	-
table 3 (xi) (Brinell hardness)	-
Table 3 (xiv) (Surface hardness)	-

-
Excluding Critical dimension, Pitch length

122

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.9.1 (Copper- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Iron- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-
6.1 ("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-
6.2 (Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-
8 ("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-
10 (Tensile test)	-
Cl.9.1 (Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.9.1 (Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-

-
Excluding Total impurities, Ti+V

123

IS 5484 (2023)

EC GRADE ALUMINIUM ROD PRODUCED BY CONTINUOUS CASTING AND ROLLING - SPECIFICATION

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-6.1 (Grades and chemical composition of EC grade aluminium rod produced)	-
Cl-6.2 (Chemical analysis of the material)	-
Cl-9 (Ultimate tensile strength and elongation)	-
Cl-10.1 (electrical conductivity)	-
Cl-10.1.1 (Resistivity and Conductivity Limit)	-
Cl-11 (Dimensions)	-
Cl-13 (Finish and freedom from defects)	-
Cl-14 (Rejection and retest)	-
Cl-16 (Marking)	-
12 (Joint)	-
Cl.6.1 as per IS 4026 (Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.6.1 as per IS 4026 (Iron - IS 504 and its parts or any other intrumental/chemical methods)	-
Cl.6.1 as per IS 4026 (Copper - IS 228 and its parts or any other intrumental/chemical methods)	-
Cl.6.1 as per IS 4026 (Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-
Cl.6.1 as per IS 4026 (Magnesium - IS 228 and its parts or any other intrumental/chemical methods)	-
Cl.6.1 as per IS 4026 (Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-
Cl.6.1 as per IS 4026 (Zinc - IS 228 and its parts or any other intrumental/chemical methods)	-
Cl.6.1 as per IS 4026 (Titanium - IS 228 and its parts or any other intrumental/chemical methods)	-
cl 6.1 (Boron)	-
cl 6.1 (Gallium)	-
cl 6.1 (Zirconium)	-
cl 6.1 (titanium+vanadium)	-
cl 6.1 (aluminium)	-

-
Test facility is not available for vanadium

124

IS 1293 (2005)

Plugs and socket- outlets of rated voltage up to and including 250 volts and rated current up to 16 amperes

Please see remarks View breakup
Plugs & Portable Socket Outlets-2.5A (Only Plugs)-Non-rewiable-Rs.5300/-, Plugs with inslulating sleeves-Rs.5400/- 6A-Rewirable-Rs.5450/-, Non-rewirable-Rs.5500/-, Plugs with insulating sleeves-Rs.6850/-, 10A-Rewirable-Rs.5550/-, Non-rewirable-Rs.5600/-, Plugs with insulating sleeves-Rs.7000/-, 16A-Rewirable-Rs.5750/-, Non-rewiraable-Rs.5800/-, Plugs with insulating sleeves-Rs.7200/-. FIXED SOCKET OUTLETS-6A with screw terminals-5700/-, with screwless terminals-Rs.6650/-, 10A with screw terminals-Rs.5850/-, with screwless terminals-Rs.7250/-, 16A with screw terminals-Rs.6050/-, with screwless terminals-Rs.8100/-, 6/16A with screw terminals-Rs.7800/-, with screwless terminals-Rs.9850/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
29.0 (Resistance to Rusting)	-
28.2 (Resistance to Tracking)	-
8 (Marking)	-
9 (6A/10A )	-
9 (6A/10A )	-
9 (6A/10A )	-
9 (6A/10A )	-
9 (6A/10A )	-
9 (16 A)	-
9 (16 A)	-
9 (16 A)	-
9 (16 A)	-
9 (16 A)	-
10.1 (Protection against Electric Shock)	-
10.1 (Protection against Electric Shock)	-
10.4 (Protection against Electric Shock)	-
12.1 (Terminals)	-
14.1 (Construction of Plugs & Portables socket outlet )	-
14.2 (Construction of Plugs & Portables socket outlet )	-
14.3 (Construction of Plugs & Portables socket outlet )	-
14.7 (Construction of Plugs & Portables socket outlet )	-
14.8 (Construction of Plugs & Portables socket outlet )	-
14.9 (Construction of Plugs & Portables socket outlet )	-
14.9 (Construction of Plugs & Portables socket outlet )	-
14.1 (Construction of Plugs & Portables socket outlet )	-
14.11 (Construction of Plugs & Portables socket outlet )	-
14.15 (Construction of Plugs & Portables socket outlet )	-
23.1 (Flexible cables & their connection )	-
23.2 (Flexible cables & their connection )	-
23.3 (Flexible cables & their connection )	-
23.4 (Flexible cables & their connection )	-
24.2 (For Portable single socket outlets/ plugs)	-
24.4 (For Portable socket outlets/ plugs)	-
24.5 (For Portable single socket outlets/ plugs)	-
24.9 (For portable multiple and combined socket outlets)	-
24.1 (For plugs)	-
24.15 (Verification of the Removal of Covers or Cover-Plates )	-
24.16 (Verification of the Removal of Covers or Cover-Plates )	-
24.17 (Verification of the Removal of Covers or Cover-Plates )	-
24.18 (Verification of the Removal of Covers or Cover-Plates )	-
28.1.2 (Addiitional tests for plugs with pins provided with insulating sleeves)	-
6.0 (Ratings)	-
6.0 (Ratings)	-
8.0 (Marking)	-
8.0 (Marking)	-
8.0 (Marking)	-
8.0 (Marking)	-
8.0 (Marking)	-
8.0 (Marking)	-
8.0 (Marking)	-
8.0 (Marking)	-
8.0 (Marking)	-
8.0 (Marking)	-
9.0 (Checking of dimensions)	-
9.0 (6A/10A )	-
9.0 (6A/10A )	-
9.0 (6A/10A )	-
9.0 (16 A)	-
9.0 (16 A)	-
9.0 (16 A)	-
10.1 (Protection against Electric Shock)	-
10.1 (Protection against Electric Shock)	-
10.3 (Protection against Electric Shock)	-
10.5 (Protection against Electric Shock)	-
10.6 (Protection against Electric Shock)	-
11.1 (Provision for Earthing)	-
11.2 (Provision for Earthing)	-
11.5 (Provision for Earthing)	-
12.1 (Terminals)	-
12.2.1 (Terminals)	-
12.2.2 (Terminals)	-
12.2.3 (Terminals)	-
12.2.4 (Terminals)	-
12.2.5 (Terminals)	-
12.2.7 (Terminals)	-
12.2.9 (Terminals)	-
12.2.10 (Terminals)	-
12.2.11 (Terminals)	-
13.1 (Construction of fixed Socket Outlets)	-
13.2 (Construction of fixed Socket Outlets)	-
13.3 (Construction of fixed Socket Outlets)	-
13.4 (Construction of fixed Socket Outlets)	-
13.4 (Construction of fixed Socket Outlets)	-
13.4 (Construction of fixed Socket Outlets)	-
13.4 (Construction of fixed Socket Outlets)	-
13.4 (Construction of fixed Socket Outlets)	-
13.5 (Construction of fixed Socket Outlets)	-
13.9 (Construction of fixed Socket Outlets)	-
13.1 (Construction of fixed Socket Outlets)	-
13.16 (Construction of fixed Socket Outlets)	-
13.14 (Construction of fixed Socket Outlets)	-
13.17 (Construction of fixed Socket Outlets)	-
15.0 (Interlocked socket-outlets)	-
16.1 (Resistance to Ageing )	-
16.3 (Resistance to humidity)	-
17.1 (Insulation Resistance)	-
17.2 ( Electric Strength)	-
18.0 (Operation of Earthing Contacts)	-
19.0 (Temperature Rise )	-
20.0 (Making & Breaking Capacity)	-
21.0 (Normal Operation)	-
21.0 (Normal Operation)	-
21.0 (Normal Operation)	-
21.0 (Normal Operation)	-
22.1 (Verification of Max withdrawal force)	-
22.2 (Verification of Minimum withdrawal force)	-
24.1 (a) Mechanical Strength )	-
24.3 (a) For surface type socket outlet)	-
24.8 (c) For shuttered socket-outlets )	-
24.14.1 (e)Verification of the Non-removal of Covers or Cover-Plates )	-
24.14.2 (f)Verification of the Removal of Covers or Cover-Plates )	-
25.1 (Resistance to heat)	-
25.2 (Resistance to heat)	-
25.3 (Resistance to heat)	-

-
Except- Sockets having screwless terminal (Cl 12.3)

125

IS 723 (2023)

Steel Countersunk Head Wire Nails ï¿½ Specification ( Second Revision )

All sizes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimensions & tolerances (Except 120° angle))	-
4.2 (Bend of shank)	-
5 (General requirements (Except Concentricity of head with the shank))	-
6 (Finish)	-
7 (Bend test)	-
Cl.3 (Carbon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.3 (Sulphur- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.3 (Phosphorous- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.3 (Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.3 (Silicon- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.3 (Copper- Relevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.3 (Manganese- IRelevant parts of IS 228 or any other established chemical/instrumental method)	-
Cl.3 (Aluminium-Relevant parts of IS 228 or any other established chemical/instrumental method)	-

-
Chem- Wire Diameter Should be greater than 3 mm Mech- except Cl 8 Critical Dimensions

126

IS 18531 (2023)

Textiles Jute and polypropylene blended bags for packing 50 kg food grains Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1 (Manfacture)	-
4.1.2 (Manfacture)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.3 (Hemming at the Mouth)	-
4.3 (Hemming at the Mouth)	-
4.4 (Capacity)	-
4.5 (Freedom from Defects)	-
4.5 (Freedom from Defects)	-
4.5 (Freedom from Defects)	-
4.5 (Freedom from Defects)	-
4.5 (Freedom from Defects)	-
4.5 (Freedom from Defects)	-
4.5 (Freedom from Defects)	-
5.1, Table 1 (Outside length,cm)	-
5.1, Table 1 (Outside width,cm)	-
5.1, Table 1 (Ends/dm)	-
5.1, Table 1 (Picks/dm)	-
5.1, Table 1 (Corrected mass/bag, g)	-
5.1, Table 1 (Average breaking strength - Warpway)	-
5.1, Table 1 (Average breaking strength - Weftway)	-
5.1, Table 1 (Average seam strength)	-
5.1, Table 1 (Moisture content,%)	-
5.1, Table 1 (Oil content on oven dry de-oiled material)	-
5.1, Table 1 (Jute content, %)	-

-
-

127

IS 16651 (2017)

High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8.2 / Table 5 (Physical Properties)	-
Cl 8.2 / Table 5 (Physical Properties)	-
Cl 8.2 / Table 5 (Physical Properties)	-
6.2 (The values for the nominal cross-sectional area)	-
Cl 8.6 (Charpy Impact Test)	-
9.3 (Bend Test)	-
9.4 (Rebend Test)	-
Cl 5.2 (Deformations and Surface Characteristics)	-
Clause-4.3.1, Table- 1 (CARBON)	-
Clause-4.3.1, Table- 1 (PHOSPHURS)	-
Clause-4.3.1, Table- 1 (MANGANESE)	-
Clause-4.3.1, Table- 1 (NITROGEN)	-
Clause-4.3.1, Table- 1 (SILICON)	-
Clause-4.3.1, Table- 1 (CHROMIUM)	-
Clause-4.3.1, Table- 1 (COPPER)	-
Clause-4.3.1, Table- 1 (MOLYBDENUM)	-
Clause-4.3.1, Table- 1 (NICKEL)	-
Table-1, Clause - 4.3.1 (SULPHUR)	-

-
Excluding Fatigue test, C(<0.05 %), Mo(>1.5%)

128

IS 12254 (2021)

POLYVINYLCHLORIDE PVC INDUSTRIAL BOOTS - SPECIFICATION Second Revision

For all type and variety

20400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4.8.1 (Conductive Footwear)	-
Cl.6.1 (Volatility- IS 12240 (Part 4))	-
Cl.6.2 (Lead Content-IS 12240 (Part 5),)	-
Table 1 as per IS 17011 2018 (pH)	-
Table 1 as per IS 17011 2018 (Phthalates (each individual phthalate))	-
Table 1 as per IS 17011 2018 (Nickel, on skin contact)	-
Table 1 as per IS 17011 2018 (Allergenic and carcinogenic disperse dyes)	-
Table 1 as per IS 17011 2018 (Aromatic amines released from Azo dyes (each individual amine))	-
Table 1 as per IS 17011 2018 (Chromium (VI))	-
5.2 (Size)	-
5.3 (Height)	-
5.4.2 (Ergonomic feature)	-
5.4.3 (Sole bond)	-
5.4.5 (Leak proofness)	-
5.4.6.2 (Internal length of toecaps)	-
5.4.6.4 (Impact resistance)	-
5.4.6.5 (Compression resistance)	-
5.4.7 (Colour)	-
5.4.8.3.2 (Penetration resistance)	-
5.4.8.4 (Cut resistance)	-
5.4.8.6 (Outsole resistance to fuel oil)	-
5.5.1 (Upper material)	-
5.5.2 (Upper tensile strength)	-
5.5.3 (Upper flexing)	-
5.5.4 (Upper Hardness)	-
5.6.1 (Lining material)	-
5.6.2 (Lining Tear strength)	-
5.6.3 (Lining abrasion)	-
5.6.4 (Lining adhesion with upper)	-
5.7.1 (Insole material)	-
5.7.2 (Insole abrasion)	-
5.7.3 (Water absorption and desorption)	-
5.9.1 (Insock material)	-
5.9.2 (Inscok abrasion resistance)	-
5.9.3 (Insock water absorption and desorption)	-
5.11.1 (Outsole material)	-
5.11.2 (Outsole density)	-
5.11.3 (Outsole Interlayer bond)	-
5.11.4 (Outsole tear)	-
5.11.5 (Outsole Abrasion)	-
5.11.6 (Outsole hardness)	-
5.11.7 (Outsole flexing)	-
Cl..4.1 of IS 17011 (Phthallate: DEHP)	-
Cl..4.1 of IS 17011 (Phthallate: DIBP)	-
Cl..4.1 of IS 17011 (Phthallate: DOP)	-
Cl..4.1 of IS 17011 (Phthallate: DBP)	-
Cl..4.1 of IS 17011 (Phthallate: BBP)	-
Cl..4.1 of IS 17011 (Phthallate: DINP)	-
Cl..4.1 of IS 17011 (Phthallate: DIDP)	-
Cl..4.1 of IS 17011 (Organotin: Dibutyltin)	-
Cl..4.1 of IS 17011 (Organotin: Dibutyltin Dichloride)	-
Cl..4.1 of IS 17011 (Organotin: Dioctyltin)	-
Cl..4.1 of IS 17011 (Organotin: Monobutyltin)	-
Cl..4.1 of IS 17011 (Organotin: Tributyltin)	-
Cl..4.1 of IS 17011 (Organotin: Triphenyltin)	-
Cl..4.1 of IS 17011 (Organotin: Monoctyltin)	-
Cl..4.1 of IS 17011 (Organotin: Bis (tributyltin) oxide)	-
Cl.4.1 (Table B-1 Sl I) (Aromatic Amines: 4-aminobiphenyl)	-
Cl.4.1 (Table B-1 Sl II) (Aromatic Amines: Benzidine)	-
Cl.4.1 (Table B-1 Sl III) (Aromatic Amines: 4-chloro-o-toluidine)	-
Cl.4.1 (Table B-1 Sl IV) (Aromatic Amines: 2-naphthylamine)	-
Cl.4.1 (Table B-1 Sl V) (Aromatic Amines :o-aminoazotoluene)	-
Cl.4.1 (Table B-1 Sl VI) (Aromatic Amines: 2-amino-4-nitrotoluenem)	-
Cl.4.1 (Table B-1 Sl VII) (Aromatic Amines: p-chloroaniline)	-
Cl.4.1 (Table B-1 Sl VIII) (Aromatic Amines: 2,4-diaminoanisole)	-
Cl.4.1 (Table B-1 Sl IX) (Aromatic Amines : 4,4’- diaminodiphenylmethane:)	-
Cl.4.1 (Table B-1 Sl X) (Aromatic Amines : 3,3’-dichlorobenzidine)	-
Cl.4.1 (Table B-1 Sl XI) (Aromatic Amines : 3,3’-dimethoxybenzidine)	-
Cl.4.1 (Table B-1 Sl XII) (Aromatic Amines : 3,3’-dimethylbenzidine)	-
Cl.4.1 (Table B-1 Sl XIII) (Aromatic Amines: 3,3’-dimethyl-4,4’-diaminodiphenylmethane)	-
Cl.4.1 (Table B-1 Sl XIV) (Aromatic Amines : p-cresidine)	-
Cl.4.1 (Table B-1 Sl XV) (Aromatic Amines : 4,4’-methylene-bis(2-chloroaniline):)	-
Cl.4.1 (Table B-1 Sl XVI) (Aromatic Amines :4,4’-oxydianiline)	-
Cl.4.1 (Table B-1 Sl XVII) (Aromatic Amines:4,4’-thiodianiline)	-
Cl.4.1 (Table B-1 Sl XVIII) (Aromatic Amines :o-toluidine:)	-
Cl.4.1 (Table B-1 Sl XIX) (Aromatic Amines: 2,4-toluylendiamine)	-
Cl.4.1 (Table B-1 Sl XX) (Aromatic Amines: 2,4,5-trimethylaniline)	-
Cl.4.1 (Table B-1 Sl XXI) (Aromatic Amines :2,4-dimethylaniline)	-
Cl.4.1 (Table B-1 Sl XXII) (Aromatic Amines: 2,6-dimethylaniline:)	-
Cl.4.1 (Table B-1 Sl XXIII) (Aromatic Amines :2-methoxyaniline)	-
Cl.4.1 (Table B-1 Sl XXIV) (Aromatic Amines :4-aminoazobenzene)	-
Cl. No.4.1,Table 1 of IS 17011 (Formaldehyde (free or released by partial hydrolysis))	-
Cl. 4.1 of IS 17011 (DMFU)	-
Cl. No.4.1,Table 1 of IS 17011 (Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-
Cl. No.4.1,Table 1 of IS 17011 (Allergenic and Carcinogenic Disperse Dyes)	-
Cl.No5.3.6(IS 17011),Table 1(ix) (PCP-TeCP-TriCP polychorophenols)	-

-
Chem- Complete, Material declaration required for Innocuousness test. Mech- Except Cold Flex Resistance as per Cl. 5.5.5. Classification, design and protection level to be declared. Separate raw material for upper, lining, insole to be provided.

129

IS 17043 (2018)

Derby shoes - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5.5.1 (Electrical Properties Antistatic )	-
5.0 (Innocuosness test IS 17011)	-

-
Chem - Excluding Allergenic & Carcinogenic Dyes, Organotin Compounds, Polychlorophenols Mech- Tag retention (Cl 4.15.2), Pull out test of eyelet (Cl 4.14)

130

IS 17012 (2018)

High ankle tactical boots with pu - Rubber sole - Specification

For all design and size

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5.5 (Antistatic test)	-
5.0 (Innocuousness Test IS 17011)	-
4.2 (Design )	-
4.3.1 (Size)	-
4.3.2 (Weight)	-
4.4 (Height of upper )	-
4.5.1 (Construction)	-
4.5.2 (Ergonomic Feature)	-
4.5.3.1 (Upper/outsole bond strength)	-
4.5.3.2 (Interayer bond strength)	-
4.6.1 (Thickness )	-
4.6.2 (Tear Strength)	-
4.6.3 (Water Penetration and water absorption )	-
4.7.1 (Material vamp & Quarter)	-
4.7.3 (Tear Strength)	-
4.7.4 (Abrasion resistance )	-
4.7.5 (Water Vapour permeability & coefficient )	-
4.8 (Thickness Toe puff & counter stiffener)	-
4.9.1 (Thickness)	-
4.9.2 (Abrasion resistance )	-
4.9.3 (Water absorption & desorption percent)	-
4.10.2 (Abrasion resistance )	-
4.10.3 (Water absorption & desorption percent)	-
4.11.1 (Thickness )	-
4.11.2 (Tear Strength)	-
4.12.1 (Thickness )	-
4.12.2 (Tear Strength)	-
4.13 (Breaking Strength of thread )	-
4.14.2 (Thickness)	-
4.14.3 (Sole Density )	-
4.14.4 (Tear Strength)	-
4.14.5 (Abrasion resistance )	-
4.14.6 (Hardness (IRHD))	-
4.14.7 (Ageing test)	-
4.14.8 (Flexing resistance )	-
4.14.9 (Resistance to hot contact )	-
4.15 (D-ring & Hooks )	-
4.16.1 (Length of lace )	-
4.16.2 (Breaking Strength of lace )	-
4.5.4 (Slip Resitance)	-
Cl.4.1 (Table B-1 Sl I) (Aromatic Amines: 4-aminobiphenyl)	-
Cl.4.1 (Table B-1 Sl II) (Aromatic Amines: Benzidine)	-
Cl.4.1 (Table B-1 Sl III) (Aromatic Amines: 4-chloro-o-toluidine)	-
Cl.4.1 (Table B-1 Sl IV) (Aromatic Amines: 2-naphthylamine)	-
Cl.4.1 (Table B-1 Sl V) (Aromatic Amines :o-aminoazotoluene)	-
Cl.4.1 (Table B-1 Sl VI) (Aromatic Amines: 2-amino-4-nitrotoluenem)	-
Cl.4.1 (Table B-1 Sl VII) (Aromatic Amines: p-chloroaniline)	-
Cl.4.1 (Table B-1 Sl VIII) (Aromatic Amines: 2,4-diaminoanisole)	-
Cl.4.1 (Table B-1 Sl IX) (Aromatic Amines : 4,4’- diaminodiphenylmethane:)	-
Cl.4.1 (Table B-1 Sl X) (Aromatic Amines : 3,3’-dichlorobenzidine)	-
Cl.4.1 (Table B-1 Sl XI) (Aromatic Amines : 3,3’-dimethoxybenzidine)	-
Cl.4.1 (Table B-1 Sl XII) (Aromatic Amines : 3,3’-dimethylbenzidine)	-
Cl.4.1 (Table B-1 Sl XIII) (Aromatic Amines: 3,3’-dimethyl-4,4’-diaminodiphenylmethane)	-
Cl.4.1 (Table B-1 Sl XIV) (Aromatic Amines : p-cresidine)	-
Cl.4.1 (Table B-1 Sl XV) (Aromatic Amines : 4,4’-methylene-bis(2-chloroaniline):)	-
Cl.4.1 (Table B-1 Sl XVI) (Aromatic Amines :4,4’-oxydianiline)	-
Cl.4.1 (Table B-1 Sl XVII) (Aromatic Amines:4,4’-thiodianiline)	-
Cl.4.1 (Table B-1 Sl XVIII) (Aromatic Amines :o-toluidine:)	-
Cl.4.1 (Table B-1 Sl XIX) (Aromatic Amines: 2,4-toluylendiamine)	-
Cl.4.1 (Table B-1 Sl XX) (Aromatic Amines: 2,4,5-trimethylaniline)	-
Cl.4.1 (Table B-1 Sl XXI) (Aromatic Amines :2,4-dimethylaniline)	-
Cl.4.1 (Table B-1 Sl XXII) (Aromatic Amines: 2,6-dimethylaniline:)	-
Cl.4.1 (Table B-1 Sl XXIII) (Aromatic Amines :2-methoxyaniline)	-
Cl.4.1 (Table B-1 Sl XXIV) (Aromatic Amines :4-aminoazobenzene)	-
Cl.4.1 (Table B-11) (PCP-TeCP-TriCP polychlorophenols)	-
Cl.1.4.1 of IS 17011 (DMFU)	-
Cl.1.4.1 of IS 17011 (Table B Sl I ) (Phthalate: DINP)	-
Cl.1.4.1 of IS 17011 (Table B Sl II ) (Phthalate:: DNOP)	-
Cl.1.4.1 of IS 17011 (Table B Sl III ) (Phthalate: DEHP)	-
Cl.1.4.1 of IS 17011 (Table B Sl IV ) (Phthalate: DIDP)	-
Cl.1.4.1 of IS 17011 (Table B Sl V) (Phthalate: BBP)	-
Cl.1.4.1 of IS 17011 (Table B Sl VI ) (Phthalate:DBP)	-
Cl.1.4.1 of IS 17011 (Table B Sl VII ) (Phthalate: DIBP)	-
Cl.4.1 (Annex-A Sl I ) (Organotin: Dibutyltin)	-
Cl.4.1 (Annex-A Sl II ) (Organotin: Dibutyltin Dichloride)	-
Cl.4.1 (Annex-A Sl III ) (Organotin: Dioctyltin)	-
Cl.4.1 (Annex-A Sl IV) (Organotin: Monobutyltin)	-
Cl.4.1 (Annex-A Sl V ) (Organotin: Tributyltin)	-
Cl.4.1 (Annex-A Sl VI) (Organotin: Triphenyltin)	-
Cl.4.1 (Annex-A Sl VII ) (Organotin: Monoctyltin)	-
Cl.4.1 (Annex-A Sl VIII) (Organotin: Bis (tributyltin) oxide)	-
Cl.1.4.1 of IS 17011 (pH)	-
Cl. No.8.6.1,Table 1 of IS 17011 (Chromium (VI))	-
Cl. No.8.6.1,Table 1 of IS 17011 (Formaldehyde (free or released by partial hydrolysis))	-
Cl. No.8.6.1,Table 1 of IS 17011 (Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-
Cl.8 - Table No 1 (Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988)	-
Cl.4.1 (Table B-3) (Allergenic and Carcinogenic Disperse Dyes)	-

-
Mech Quantity:- 5 Pairs + Raw material of upper, Lining, Insole, Toe puff, Counter stiffener, closing thread, outsole, midsole, collar Chem- Material declaration required for Innocuousness test.

131

IS 3854 (2023)

Switches for Domestic and Similar Purposes - Specification (Third Revision)

Check test charges remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4 (General Requirements)	-

-
Excluding Making & Breaking & Normal operation test apparatus, Switches Intended for Externally

132

IS 3930 (1994)

Flame and induction hardening steels - Specification (Second Revision)

Rs. 750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7.1, 7.2, 7.3- table 2 (Carbon, percent)	-
Cl 7.1, 7.2, 7.3- table 2 (Silicon, percent)	-
Cl 7.1, 7.2, 7.3- table 2 (Manganese, percent)	-
Cl 7.1, 7.2, 7.3- table 2 (Sulphur, percent)	-
Cl 7.1, 7.2, 7.3- table 2 (Phosphorous, percent)	-
Cl 7.1, 7.2, 7.3- table 2 (Chromium, percent)	-
Cl 7.1, 7.2, 7.3- table 2 (Molybdenum, percent)	-
Cl 7.1, 7.2, 7.3- table 2 (Nickel, percent)	-
6 (Freedom from defects)	-
9 (Hardness)	-
10.1 (Mechanical property in the hardened condition)	-
10.2 (Mechanical property in the tempered condition)	-
13.1 (Dimensional Tolerance)	-
13.3 (Tolerance on Straightness)	-
11 (Grain Size)	-
7.2 Table - 3 (ix) (Vanadium)	-

-
Excluding Surface defects, V, Sn and other micro alloying elements

133

IS/ISO 11951 (2016)

Cold - Reduced tinmill products - Blackplate (First Revision)

For all grades except for the test mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7.1, Annex C (Carbon, % mass fraction)	-
Cl 7.1, Annex C (Sulphur, % mass fraction)	-
Cl 7.1, Annex C (Phosphorous, % mass fraction)	-
Cl 7.1, Annex C (Manganese, % mass fraction)	-
8.2 (Hardness)	-
8.3 (Tensile test)	-
9.2.1 (Coil thickness)	-
9.2.2 (Feather edge)	-
9.3 (Coil width)	-
9.4 (Coil length)	-
9.5 (Edge camber of trimmed coils)	-

-
Excluding Si

134

IS 15895 (2018)

High alumina refractory cement - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (Fineness)	-
4.4 (Strength - 1 day)	-
4.5 (Setting time - Final)	-
Cl 4.3.2, table 1, s.no-i (a) (Chemical Constituents- Al2O3, percent)	-
Cl 4.3.2, table 1, s.no-i (b) (Chemical Constituents- SiO2, percent)	-
Cl 4.3.2, table 1, s.no-i (c) (Chemical Constituents- Fe2O3, percent)	-
Cl 4.3.2, table 1, s.no-i (e) (Chemical Constituents- CaO, percent)	-
Cl 4.3.2, table 1, s.no-i (f) (Chemical Constituents- MgO, percent)	-
4.3.2 (TiO2 - For Medium purity)	-

-
Excluding Refractoriness

135

IS 18163 (2023)

Textiles Light weight jute sacking bags for packing 35 kg groundnut with shell Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (Manufacture)	-
4.1.1 (Manufacture)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.2 (Seam)	-
Cl-4.2 (Seam)	-
Cl-4.3 (Safety Stitch)	-
Cl-7 (Marking)	-
Cl-4.4 (Hemming at the Mouth)	-
4.4 (Hemming at the Mouth)	-
Cl-4.5 (Freedom from Defects)	-
Cl-5.2, Table 2 (i) (Total number of bags per bale)	-
Cl-5.2, Table 2 (ii) (Number of bags per bundle)	-
Cl-5.2, Table 2 (iii) (Contract mass of a bale, kg)	-
Cl-5.2, Table 2 (iv) (Corrected net mass of a bale, kg)	-
Cl-5.2, Table 2 (v) (Number of joined bags per bundle of 25 bags)	-
Cl-5.3 (contract moisture regain)	-
Cl-5.4.2 (Additional Requirements for Labelling as Environment Friendly Products (Optional)- Specific Requirements)	-
Cl-4.1.1 & 5.1, Table 1, i (a) (Dimensions-Outside length, cm)	-
Cl-4.1.1 & 5.1, Table 1, i (b) (Dimensions- Outside width, cm)	-
Cl-4.1.1 & 5.1, Table 1 (ii) (Ends/dm)	-
Cl-4.1.1 & 5.1, Table 1, iii (Picks/dm)	-
Cl-4.1.1 & 5.1, Table 1, iv (Corrected mass/bag, g, percent)	-
Cl-4.1.1 & 5.1, Table 1, v (a) (Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): - Warp way)	-
Cl-4.1.1 & 5.1, Table 1, v (b) (Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): - Weft way)	-
Cl-4.1.1 & 5.1, Table 1, vi (Average seam strength (5 cm × 20 cm ravelled strip), Min, N (kgf))	-
Cl-4.1.1 & 5.1, Table 1, vii (Moisture regain, percent, Max)	-
Cl-4.1.1 & 5.1, Table 1, viii (Oil content on dry de-oiled material, Max)	-

-
Declaration to be provided for type of bag

136

IS 18162 (2023)

Textiles Light weight jute sacking bags for packing 50 kg pulses and soyabean Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Manufacture)	-
4.1.1 (Manufacture)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.3 (Safety Stitch)	-
4.4 (Hemming at the Mouth)	-
4.4 (Hemming at the Mouth)	-
Cl-4.5 (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
Cl-4.1.1 & 5.1, Table 1, i (a) (Dimensions-Outside length, cm)	-
Cl-4.1.1 & 5.1, Table 1, i (b) (Dimensions- Outside width, cm)	-
Cl-4.1.1 & 5.1, Table 1 (ii) (Ends/dm)	-
Cl-4.1.1 & 5.1, Table 1, iii (Picks/dm)	-
Cl-4.1.1 & 5.1, Table 1, iv (Corrected mass/bag, g, percent)	-
Cl-4.1.1 & 5.1, Table 1, v (a) (Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): - Warp way)	-
Cl-4.1.1 & 5.1, Table 1, v (b) (Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): - Weft way)	-
Cl-4.1.1 & 5.1, Table 1, vi (Average seam strength (5 cm × 20 cm ravelled strip), Min, N (kgf))	-
Cl-4.1.1 & 5.1, Table 1, vii (Moisture regain, percent, Max)	-
Cl-4.1.1 & 5.1, Table 1, viii (Oil content on dry de-oiled material, Max)	-
4.3 (Safety Stitch)	-

-
Declaration to be provided for type of bag

137

IS 18161 (2023)

Textiles Light weight jute sacking bags for packing 50 kg mustard seed niger seed and ragi Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Manufacture)	-
4.1.1 (Manufacture)	-
4.2 (Seam)	-
4.2 (Seam)	-
4.2 (Seam)	-
Cl-4.2 (Seam)	-
4.3 (Safety Stitch)	-
4.3 (Safety Stitch)	-
4.4 (Hemming at the Mouth)	-
4.4 (Hemming at the Mouth)	-
Cl-4.5 (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
4.5 & 8.4.1 Annex- B (Freedom from Defects)	-
Cl-4.1.1 & 5.1, Table 1, i (a) (Dimensions-Outside length, cm)	-
Cl-4.1.1 & 5.1, Table 1, i (b) (Dimensions- Outside width, cm)	-
Cl-4.1.1 & 5.1, Table 1 (ii) (Ends/dm)	-
Cl-4.1.1 & 5.1, Table 1, iii (Picks/dm)	-
Cl-4.1.1 & 5.1, Table 1, iv (Corrected mass/bag, g, percent)	-
Cl-4.1.1 & 5.1, Table 1, v (a) (Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): - Warp way)	-
Cl-4.1.1 & 5.1, Table 1, v (b) (Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): - Weft way)	-
Cl-4.1.1 & 5.1, Table 1, vi (Average seam strength (5 cm × 20 cm ravelled strip), Min, N (kgf))	-
Cl-4.1.1 & 5.1, Table 1, vii (Moisture regain, percent, Max)	-
Cl-4.1.1 & 5.1, Table 1, viii (Oil content on dry de-oiled material, Max)	-

-
Declaration to be provided for type of bag

138

IS 1856 (2021)

Steel wire ropes for haulage purposes - Specification Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Rope Size and Tolerances.)	-
5 (Minimum Breaking Force up to 32 mm dia.)	-
6.1 (Core)	-
6.2 (Joints)	-
6.3 (Lay)	-
6.4 (Mass and)	-
7 (Galvanizing)	-

-
Breaking load facility available upto 32 mm dia.

139

IS 12679 (2021)

By-product Gypsum for Use in Plaster Blocks and Boards - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4, Table-1, i) (P2O5(% by mass), Max- IS 6361)	-
Cl-4, Table-1, ii) (F(% by mass), Max- IS 2411)	-
Cl-4, Table-1, iii) (Na2O(% by mass), Max- IS 9497)	-
Cl-4, Table-1, iv) (K2O(% by mass), Max- IS 9497)	-
Cl-4, Table-1, v) (Organic matter(% by mass), Max- IS 2720 (Part 22))	-
Cl-4, Table-1, vi) (CaSO4.2H2O(% by mass), Max- IS 1288)	-
Cl-4, Table-1, vii) (Cl as NaCl(% by mass), Max- IS 1288)	-
Cl-4, Table-1, viii) (pH of 10 percent aqueous suspension of gypsum, Min)	-
Cl-4, Table-1, ix) (Moisture (free water),(% by mass), Max- IS 1288)	-

-
Complete

140

IS 1293 (2019)

Plugs and socket - Outlets of rated Voltage up to and including 250 Volts and rated current up to and including 16 amperes - Specification (Third Revision)

6 & 16 Amp, Up to 240 volts, Ordinary type (IPX0)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1.1 (Accessories Classification)	-
7.1.2 (Accessories Classification)	-
7.1.3 (Accessories Classification)	-
7.1.4 (Accessories Classification)	-
7.1.5 (Accessories Classification)	-
7.2.1 (Socket-Outlets Classification)	-
7.2.2 (Socket-Outlets Classification)	-
7.2.3 (Socket-Outlets Classification)	-
7.2.4 (Socket-Outlets Classification)	-
7.3 (Plug Classification)	-
8.1 (MARKING)	-
8.8 (MARKING)	-
8.9 (MARKING)	-
9.1 (CHECKING OF DIMENSIONS)	-
9.2 (CHECKING OF DIMENSIONS)	-
10.1 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.3 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.5 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.6 (PROTECTION AGAINST ELECTRIC SHOCK)	-
10.7 (PROTECTION AGAINST ELECTRIC SHOCK)	-
11.1 (PROVISIONS FOR EARTHING)	-
11.4 (PROVISIONS FOR EARTHING)	-
11.5 (PROVISIONS FOR EARTHING)	-
11.6 (PROVISIONS FOR EARTHING)	-
12.1.2 (TERMINALS)	-
12.2.1 (TERMINALS)	-
12.2.2 (TERMINALS)	-
12.2.3 (TERMINALS)	-
12.2.4 (TERMINALS)	-
12.2.5 (TERMINALS)	-
12.2.6 (TERMINALS)	-
12.2.7 (TERMINALS)	-
12.2.8 (TERMINALS)	-
12.2.9 (TERMINALS)	-
12.2.10 (TERMINALS)	-
12.2.11 (TERMINALS)	-
13.1 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.2 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.3 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.4 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.5 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.6 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.7 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.8 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.9 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.1 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.11 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.12 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.14 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.15 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.16 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.18 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.19 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.2 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.21 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.23 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
14.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.3 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.4 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.5 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.6 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.7 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.8 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.9 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.11 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.12 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.14 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.15 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.16 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.17 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.18 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.19 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.21 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.22 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.23.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.24 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.25 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.26 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
15 (INTERLOCKED SOCKET-OUTLETS)	-
16.1 (RESISTANCE TO AGEING,)	-
16.3 (Resistance to Humidity)	-
17.1 (INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-
17.2 (INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-
17.3 (INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-
18 (OPERATION OF EARTHING CONTACTS)	-
19 (TEMPERATURE RISE)	-
20 (BREAKING CAPACITY)	-
21 (NORMAL OPERATION)	-
21 (NORMAL OPERATION)	-
21 (NORMAL OPERATION)	-
21 (NORMAL OPERATION)	-
22.1 (Verification of the Maximum Withdrawal Force)	-
22.2 (Verification of Minimum Withdrawal Force)	-
23.1 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
23.1 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
23.3 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
23.4 (FLEXIBLE CABLES AND THEIR CONNECTION)	-
24.1 (MECHANICAL STRENGTH For all kinds of fixed socket-outlets )	-
24.2 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.2 (MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.2 (MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.3 (MECHANICAL STRENGTH for fixed socket-outlets with a main part intended to be mounted directly on a surface)	-
24.4 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.5 (MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.5 (MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-
24.6 (MECHANICAL STRENGTH For screwed glands of accessories having an IP code higher than IP20)	-
24.7 (MECHANICAL STRENGTH For plug pins provided with insulating sleeves)	-
24.8 (MECHANICAL STRENGTH For shuttered socket-outlets)	-
24.9 (MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.9 (MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.1 (MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-
24.1 (MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-
24.11 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.12 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.13 (MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-
24.14.1 (MECHANICAL STRENGTH For fixed socket-outlets)	-
24.14.2 (MECHANICAL STRENGTH For fixed socket-outlets)	-
24.14.3 (MECHANICAL STRENGTH For plugs and portable socket-outlets)	-
24.15 (MECHANICAL STRENGTH )	-
24.16 (MECHANICAL STRENGTH )	-
25.1 (RESISTANCE TO HEAT Accessories and surface mounting boxes)	-
25.2 (RESISTANCE TO HEAT Parts of insulating material necessary to retain current-carrying parts of the earthing circuit in position, as well as parts of the front surface zone of thermoplastic material)	-
25.3 (RESISTANCE TO HEAT Parts of insulating material not necessary to retain current-carrying parts and parts of the earthing circuit in position, even though they are in contact with them)	-
25.4 (RESISTANCE TO HEAT )	-
26.1 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
26.2 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
26.3 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
26.4 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
26.5 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
26.6 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
26.7 (SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-
27.1 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
27.2 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
27.3 (CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-
28.1.1 (Resistance to Abnormal Heat and to Fire Glow-Wire Test)	-
28.1.2 (Resistance to Abnormal Heat and to Fire for plugs with pins provided with insulating sleeves)	-
28.2 (Resistance to Tracking For accessories other than IP code higher than IPX0 parts of insulating material retaining live parts in position)	-
29 (RESISTANCE TO RUSTING)	-
30.1 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Pressure Test at High Temperature)	-
30.2 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Static Damp Heat Test)	-
30.3 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Tests at Low Temperature)	-
30.4 (ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Impact Test at Low Temperature)	-
10.4 (PROTECTION AGAINST ELECTRIC SHOCK)	-
11.2 (PROVISIONS FOR EARTHING)	-
12.1.1 (TERMINALS)	-
13.13 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.17 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
13.22 (CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-
14.13 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
16.2 (RESISTANCE TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-
8.7 (Marking)	-
8.6 (MARKING)	-
8.5 (MARKING)	-
8.4 (MARKING)	-
8.3 (MARKING)	-
8.2 (MARKING)	-
10.2 (PROTECTION AGAINST ELECTRIC SHOCK)	-
11.3 (PROVISIONS FOR EARTHING)	-
14.10.1 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.10.2 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
14.10.3 (CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-
9.1 (a) (Dimension of plug (6/10A))	-
9.1 (b) (Dimension of plug (6/10A))	-
9.1 (c) (Dimension of plug (6/10A))	-
9.1 (d) (Dimension of plug (6/10A))	-
9.1 (e) (Dimension of plug (6/10A))	-
9.1 (f) (Dimension of plug (6/10A))	-
9.1 (g) (Dimension of plug (6/10A))	-
9.1 (h) (Dimension of plug (16 A))	-
9.1 (i) (Dimension of plug (16 A))	-
9.1 (j) (Dimension of plug (16 A))	-
9.1 (k) (Dimension of plug (16 A))	-
9.1 (l) (Dimension of plug (16 A))	-
9.1 (m) (Dimension of plug (16 A))	-
9.1 (n) ()	-

-
Except- Sockets having screwless terminal (Cl 12.3)

141

IS 3854 (1997)

Switches for domestic and similar purposes - Specification (Second Revision)

Switches having current rating 6A, 10A & 16 A ordinary

- View breakup
6A Screw type terminals-Rs.4900/-, 6A Screwless type terminals-Rs.5850/-,10A Screw type terminals-Rs.5050/-, 10A Screwless type terminals-Rs.6400/-, 16A Screw type terminals-Rs.5850/-,16A Screwless type terminals-Rs.7900/-, 20A-Rs.5250/-, 25A-Rs.5900/-, 32A-Rs.6250/-, 40A-Rs.6550/-, 63A-Rs.6200/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Ratings)	-
6.2 (Ratings)	-
7.1.1 (Classification)	-
7.1.2 (Classification)	-
7.1.3 (Classification)	-
7.1.4 (Classification)	-
7.1.5 (Classification)	-
7.1.6 (Classification)	-
7.1.7 (Classification)	-
7.1.8 (Classification)	-
7.2 (Classification)	-
8.2 (Marking)	-
8.9 (Marking)	-
8 (Marking)	-
10.1 (Protection against electric shock )	-
10.3 (Protection against electric shock )	-
11.1 (Provision for earthing)	-
12.1 (Terminals)	-
12.2.1 (Terminals)	-
12.2.2 (Connection of conductor)	-
12.2.3 (Mechanical strength of terminals)	-
12.2.4 (Resistance to corrosion)	-
12.2.5 (Undue damage to conductor)	-
12.2.6 (Terminals)	-
12.2.7 (Insertion of conductor)	-
12.2.8 (Terminals)	-
12.2.9 (Locking against accidental loosening)	-
12.2.10 (Terminals)	-
12.2.12 (Terminals)	-
12.2.11 (Distance between screw and conductor)	-
12.3.1 (Terminals)	-
13.1 (Constructional requirements )	-
13.2 (Constructional requirements )	-
13.3 (Constructional requirements )	-
13.3.1 (Constructional requirements )	-
13.3.2 (Constructional requirements )	-
13.3.3 (Constructional requirements )	-
13.4 (Constructional requirements )	-
13.5 (Constructional requirements )	-
13.6 (Constructional requirements )	-
13.7 (Constructional requirements )	-
13.8 (Constructional requirements )	-
13.9 (Constructional requirements )	-
13.1 (Constructional requirements )	-
13.11 (Constructional requirements )	-
13.12 (Constructional requirements )	-
13.13 (Constructional requirements )	-
13.14 (Constructional requirements )	-
13.15 (Constructional requirements )	-
13.15.1 (Constructional requirements )	-
13.15.2 (Constructional requirements )	-
14 (Mechanism [Cl. 14])	-
15.1 (Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-
15.2 (b)Resistance to Harmful ingress of water [Cl. 15.2])	-
15.3 (c) Resistance to Humidity [Cl. 15.3])	-
16.1 (Insulation resistance [Cl. 16.1])	-
16.2 ( Electric Strength [Cl. 16.2])	-
17 (Temperature- rise [Cl. 17])	-
18 (Marking and breaking Capacity[Cl. 18])	-
19 (Normal Operation [Cl. 19] a) General & Operation)	-
19 (b) Electric Strength)	-
14.3 (d)Test for arcing and sparking [Cl 14.3])	-
19.2 (Normal Operation (For AX type Switches) [Cl. 19.2])	-
19.2 (Normal Operation (For AX type Switches) [Cl. 19.2])	-
20 (Mechanical Strength Test [Cl. 20])	-
21 (Resistance to Heat [Cl.21])	-
21 (Resistance to Heat [Cl.21])	-
21 (Resistance to Heat [Cl.21])	-
22 (Screw, Current Carrying Part And Connection [Cl.22])	-
22.1 (i) Screw & Nuts [Cl.22.1])	-
22.4 (ii) Screw & rivets [Cl . 22.4])	-
22.3 (iii) Electrical Connections [Cl.22.3])	-
23.2 (Creepage distances, clearances and distance through sealing compound [Cl.23])	-
23 (Creepage distances, clearances and distance through sealing compound [Cl.23])	-
23 (Creepage distances, clearances and distance through sealing compound [Cl.23])	-
24.1.1 (Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-
24.2 (Resistance to tracking [For Switch other than ordinary] [Cl.24.2])	-
25 (Resistance to Rusting)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8.9 (Marking)	-
8 (Marking)	-
14.2 (Mechanism)	-

-
Excluding Making & Breaking & Normal operation test apparatus, Switches Intended for Externally Ballasted Lamp Loads apparatus, Test for Switches Intended for Self-ballasted Lamp Loads

142

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

Rs.2400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Minimum Thickness)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Minimum Socket Length)	-
Cl. 6.1 (Stress Relief Test- Appendix A)	-
6.3 (Effect on Water)	-
Cl 6.3 (Effect on Water Lead (first extraction))	-
Cl 6.3 (Effect on Water Lead (third extraction))	-
Cl 6.3 (Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-
Cl 6.3 (Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-
Cl 6.3 (Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-
CL 4.0 (Wall thickness (average of 4.0))	-
CL 5.1 (Sockt Length ( Take 4 reading and minimum will be reported))	-

-
Excluding short term hydraulic test Chemical: All except Effect on Water which is for Pipes above 60 mm Nominal dia and except for the requirement of 'Other Toxic Substances such a di-n-octyl Tin -s-s bis iso-octyl mercapto acetate' and 'butyl stearate'; Mech- All except HST.

143

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

For all sizes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.1.3 and 8.3,Table 1 ii (Thickness)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, i) (Relative density)	-
Cl.4.1.3 And 8.3,Table1 (ii) Hardness, Shore A durometer min)	-
Cl.4.1.3 And 8.3,Table1 (iv) Compression set at constant stress percent, Max)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, v) (Split tear strength, kg,Min)	-
Cl.4.1.3 And 8.3,Table 1 vi (Heat shrinkage test at 100±1°C for 1 hour max)	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii) (Flexing resistance: Maximum cut growth at 50 000 cycles)	-
Cl.4.1.3 and 8.3,Table 1 vii (Abrasion resistance at applied force of 5 N)	-
4.2 (Flexing resistance )	-
4.2 (Water absorption)	-
4.2 (Heat Shrinkage )	-
4.2 (Shrinkage at room temp)	-
4.2 (Split tear strength)	-
4.2 (Compression set)	-
4.2 (Hardness (Shore A))	-
4.2 (Density )	-
4.2 (Size & Thickness )	-
4, Cl.4.1,4.1.1,4.1.2 (Requirements)	-
Cl.4.1.3 And 8.3,Table1, iii) (Hardness, Shore A durometer min)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iii) (Change in Hardness after ageing at 100±1°C for 24hr)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iv) (Compression set at constant stress percent, Max)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vi) (Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi) (Heat shrinkage test at 100±1°C for 1 hour max)	-
Cl.4 Cl.4.1.3 And 8.3,Table1, viii) (Water absorption , percent by mass, Max)	-
5, 5.1 (Marking)	-
6, 6.1 (Packing)	-
"Cl.4 ,Cl.4.1,4.1.1,4.1.2 (Requirements ")	-
Cl.4.1.3 And 8.3,Table1 (i) Relative density)	-
Cl.4.1.3 And 8.3,Table1 (iii) Change in Hardness after ageing at 100±1°C for 24hr)	-
Cl.4.1.3 And 8.3,Table1 (vi) Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-
Cl.4.1.3 And 8.3,Table1 (viii)Water absorption , percent by mass, Max)	-
Cl.4.1.3 And 8.3,Table1 (ix)Flexing resistance)	-
5, 5.1 (Marking)	-
6, 6.1 (Packing)	-

-
Complete

144

IS 13893 (1994)

Polyurethane soles semirigid - specification

For all sizes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Design)	-
4.2 (Thickness )	-
4.3 (Relative density )	-
4.3 (Hardness Shore(A))	-
4.3 (Tensile Strength )	-
4.3 (Elongation at break)	-
4.3 (Abrasion Resistance)	-
4.3 (Flexural strength )	-
4.3 (Ross Flex test)	-
4.3.2 (Ageing test)	-
4.3.1 Table 1 vi) (Amendment 2) (Tensile Strength)	-
4.3.1 Table 1 i) (Amendment 2) (Relative Density)	-
4.3.1 Table 1 iii) (Amendment 2) (Abrasion Resistance at applied force of 10 N)	-
4.3.1 Table 1 v) (Amendment 2) (Hydrolysis Resistance, cut growth after 150000 flexes)	-
4.3.1 Table 1 viii) (Amendment 2) (Tear Strength (average force))	-
4.3.1 Table 1 iv) (Amendment 2) (Flexing Resistance, Bennewart method)	-
4.2 (Amendment 2) (Thickness)	-
4.3.1 Table 1 vii) (Amendment 2) (Elongation at break)	-
4.3.1 Table 1 ii) (Amendment 2) (Hardness, degree, Shore A)	-
5, 5.1, 5.2 (Packing And Marking)	-
Cl.5, 5.1, 5.2 (Packing And Marking)	-

-
2 nos. soles + 2 slab (200mm x 200mm, Thickness 1.8-2.2 mm) + 1 slab (200 x 200 mm, Thickness 2.8-3.2 mm)

145

IS 11169 : Part 1 (2022)

Specification for steels for cold heading cold extrusion applications: Part 1 wrought carbon and low alloy steels

For all grades except test mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
17 (Shape, Dimensions and tolerances)	-
8.1 (Tensile Test)	-
8.1 (Hardness Test)	-
8.2 (Hardenability (only Applicable to Steel Grades of Annexes B and C))	-
Cl.4.3,7.2 & Table-A.2 (Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
Cl.4.3,7.2 & Table-A.2 (Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-
CL 7.2 (Diameter ( average 8))	-
Cl. 7 (Carbon)	-
Cl. 7 (Silicon)	-
Cl. 7 (Manganese)	-
Cl. 7 (Phosphorous)	-
Cl. 7 (Sulphur)	-
Cl. 7 (Chromium)	-
Cl. 7 (Nickel)	-
Cl. 7 (Molybdenum)	-
Cl. 7 (Aluminium)	-
Cl. 7 (Boron)	-
Cl. 7 (Copper)	-

-
Prepared sample should be provided for hardenability test. Mech: Facility not available for 14.1.3.1Eddy current test Chem: Except V, Sn

146

IS 14625 (2015)

Plastics Feeding Bottles ( First Revision )

Rs 16930 (Excluding tests for material as per Cl.4.1 an View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.3.8 a) (Migration Test a) Distilled water at 40±2° hrs)	-
Cl.5.3.9.2, Table-3(i) (Specific migration , Barium)	-
Cl.5.3.9.2, Table-3(ii) (Specific migration , Cobalt)	-
Cl.5.3.9.2, Table-3(iii) (Specific migration , Copper)	-
Cl.5.3.9.2, Table-3(iv) (Specific migration , Iron)	-
Cl.5.3.9.2, Table-3(v) (Specific migration , Lithium)	-
Cl.5.3.9.2, Table-3(vi) (Specific migration , Manganese)	-
Cl.5.3.9.2, Table-3(vii) (Specific migration , Zinc)	-
Cl.5.3.9.2, Table-3(viii) (Specific migration , Antimony)	-
Cl 5.1.3 (Wall Thickness)	-
Cl 5.1.4 (Capacity)	-
Cl 5.3.2 (Transparecy)	-
Cl 5.3.3 (Leakage Test)	-
Cl 5.3.4 (Drop Test)	-
Cl 5.3.5 (Ageing Resistance)	-
Cl 5.3.7 (Product Resistance of Printed Containers)	-
4.1 (Material Identification, Bisphenol A,)	-
5.3.1 (Environmental Stress Crack Resistance,)	-
Clauses 5.3.9.2 and 5.3.9.3,Table 3, S.no.(ix) (Phthalic acid, bis(2-ethylhexyl)ester (DEHP)-ISO 18856)	-
5.3.8 b) (Migration Test b) n-Haptane at 38±1° C for 30 min)	-
Clause 5.2.1.7, S.No.(i) (Heavy metal,Antimony)	-
Clause 5.2.1.7, S.No.(ii) (Heavy metal,Arsenic)	-
Clause 5.2.1.7, S.No.(iii) (Heavy metal,Chromium)	-
Clause 5.2.1.7, S.No.(iv) (Heavy metal,Mercury)	-
Clause 5.2.1.7, S.No.(v) (Heavy metal,Cadmium)	-
Clause 5.2.1.7, S.No.(vi) (Heavy metal,Lead)	-
Clause 5.2.1.7, S.No.(vii) (Heavy metal,Barium)	-
Clause 5.2.1.7, S.No.(viii) (Heavy metal,Selenium)	-
4.1 (Material Identification, Bisphenol A,)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Antimony)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Arsenic)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Chromium)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Mercury)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Cadmium)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Lead)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Barium)	-
Sl. No. i), Table 1, Cl.5.2.1.7 (Migration of certain elements - Selenium)	-
Clause 5.3.1 (Environmental Stress crack resistance)	-
Cl.5.2.1.7, Table-1(i) (Migration of certain elements, Reqiurement as per table 1, Arsenic)	-
Cl.5.2.1.7, Table-1(ii) (Migration of certain elements, Reqiurement as per table 1, Chromium)	-
Cl.5.2.1.7, Table-1(iii) (Migration of certain elements, Reqiurement as per table 1, Mercury)	-
Cl.5.2.1.7, Table-1(iv) (Migration of certain elements, Reqiurement as per table 1, Cadmium)	-
Cl.5.2.1.7, Table-1(v) (Migration of certain elements, Reqiurement as per table 1, Lead)	-
Cl.5.2.1.7, Table-1(vi) (Migration of certain elements, Reqiurement as per table 1, Barium)	-
Cl.5.2.1.7, Table-1(vii) (Migration of certain elements, Reqiurement as per table 1, Selenium)	-
Cl.5.3.8 (Migration test a)Distilled water)	-
Cl.5.3.8 (Migration test a)n-Heptane)	-
Cl 5.3.6 (Compressive Deformation Resistance)	-

-
Excluding Material

147

IS 13997 (2014)

Drums, large open top - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, Table 1 (Dimensions-D2)	-
5, Table 1 (Dimensions-D3)	-
5, Table 1 (Dimensions-D4)	-
5, Table 1 (Dimensions-H1)	-
5, Table 1 (Dimensions-H5)	-
5, Table 1 (Dimensions-h2)	-
5, Table 1 (Dimensions-h3)	-
5, Table 1 (Dimensions-h4)	-
5, Table 1 (Dimensions-p1)	-
6.2 (The nominal thickness of steel sheets for body and ends )	-
7.1 ( CONSTRUCTION)	-
7.2 ( CONSTRUCTION)	-
8.1 (FINISH )	-
7.11 ( Locking Ring)	-
7.3 ( CONSTRUCTION- Double Seam/Spiral Seam/Triple Seam Construction for Grade A Drums)	-
7.4 ( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums-Seam rolling layers)	-
7.5 ( CONSTRUCTION)	-
7.6 ( CONSTRUCTION)	-
7.7 ( CONSTRUCTION)	-
7.8 ( CONSTRUCTION- crest to trough gap)	-
7.8 ( CONSTRUCTION- no of corrugations on the body Each side)	-
7.10(a) (Closures)	-
7.10(b) (Closures)	-
7.10(c) (Closures)	-
7.10(d) (Closures)	-

-
Excluding Al & Micro alloying elements

148

IS 1285 (2002)

Wrought aluminium and aluminium alloys - Extruded round tube and hollow sections for general engineering purposes - Specification (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5/5.1 (FREEDOM FROM DEFECTS)	-
5/5.2 (FREEDOM FROM DEFECTS)	-
7/a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - outside Dia or Inside Dia)	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - outside Dia or Inside Dia)	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - Wall thickness)	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - Allowable Deviation of Mean Diameter from Specified Diameter (Size Tolerance))	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube - Allowabte Deviation of Diameter at Any Point from Specified Diameter (Ovality Tolcrance))	-
7 of IS 1285 /a) Extruded round tube IS 2673 (DIMENSIONS AND TOLERANCE-Extruded round tube -Straightness)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 (DIMENSIONS AND TOLERANCE-Extruded hollow sections -SPECIFIED WIDTH or WIDTH ACROSS FLATS)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 (DIMENSIONS AND TOLERANCE-Extruded hollow sections - Specified WIDTH or WIDTH ACROSS FLATS)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 (DIMENSIONS AND TOLERANCE-Extruded hollow sections -SPECIFIED Wall thickness)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 (DIMENSIONS AND TOLERANCE-Extruded hollow sections -Straightness)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 (Extruded hollow sections -Twist -Permissible Twist in Total Length of piece- At extremetiy)	-
7 of IS 1285 / b) Extruded hollow sections IS 6477 ("Extruded hollow sections -Twist -ALLOWABLE DEVIATION FROM SPECIFIED ANGLE, DEGREES")	-
9 (Mechanical Comp[osition -IS 1285)	-
As per Clause 8 Table ! (Aluminium)	-
As per Clause 8 Table ! (Copper)	-
As per Clause 8 Table ! (Magnesium)	-
As per Clause 8 Table ! (Silicon)	-
As per Clause 8 Table ! (Iron)	-
As per Clause 8 Table ! (Manganese)	-
As per Clause 8 Table ! (Zinc)	-
As per Clause 8 Table ! (Titanium)	-
As per Clause 8 Table ! (Chromium)	-

-
Excluding Total impurities, V

149

IS 3224 (2021)

VALVE FITTINGS FOR COMPRESSED GAS CYLINDERS EXCLUDING LIQUEFIED PETROLEUM GAS LPG CYLINDERS SPECIFICATION Fourth Revision of IS 3224

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4.1 (Classfication)	-
Cl 6.2 (Valve Dimensions)	-
Cl 8 (" INLET CONNECTIONST:he valve inlet connection shall be provided with either taper (see 8.1) or parallel (see 8.3) threads.")	-
Cl 8 (" INLET CONNECTIONST:he valve inlet connection shall be provided with either taper (see 8.1) or parallel (see 8.3) threads.")	-

-
Excluding Hydraulic characteristics test,Slow crack growth rate test, Resistance to weathering test,Squeeze off test

150

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

For all sizes except test mentioned in remarks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3 (Nominal Diameter)	-
4.4 (Colour)	-
6.1 (Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-
6.1 (Out of Roundness (Ovality))	-
6.2 (Wall thickness (Take 8 reading and Average will be repoted))	-
7 (Finish)	-
8.2 (Reversion Test)	-
8.8 (Tensile Properties (Tensile Yield Strength and Elongation at Break))	-
8.4 (Melt Flow Rate (MFR))	-
8.8 (Tensile Properties (Tensile Yield Strength and Elongation at Break))	-
8.7 (Volatile Matter Content)	-
6.1 (Mean out side Diameter (For less than or equal to 25 mm- Average of 8 , For higher diameters average of 6))	-
6.2 (Wall thickness (Take 8 reading and Average will be repoted))	-

-
Facility not available for thermal stability, Hydraulic characteristics, water content and thermal stability

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Eastern Regional Laboratory (ERL)

(1) Annex Building & Sample-Cell: Bureau of Indian Standards, P-230, CIT Scheme, VII- M, Block-W,Kankurgachi,Kolkata-700054 (2) Main building: 1/14, CIT Scheme VII M, VIP Road, Kankurgachi,Kolkata-700054, Kolkata, Kolkata, West Bengal, 700054

- sample.erol@bis.gov.in

Scope List