BIS - LIMS (Laboratory Information Management System)

Institute for Auto Parts and Hand Tools Technology, Ludhiana

A-9, Phase-V, Focal Point, Ludhiana, Ludhiana, Ludhiana, Punjab, 141010

8427262400 iatldh@iapht.org

Scope List

Reset

74 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 3650 (2026)

Combination Side Cutting Pliers Specification (Third Revision)

all

7990 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Dimensions)	-	1200	-
Cl-4.2(cutting angle)	-	1200	-
Cl-5.1, Table-2 (i) (Head and Handle)(Material- Chrome vanadium)	-	840	-
Cl-5.1, Table-2 (ii) (Head and Handle)(Material- Chrome steel)	-	720	-
Cl-5.1, Table-2 (iii) (Head and Handle)(Material- Carbon steel)	-	600	-
Cl-5.1, Table-2 (Head and Handle)(C)	-	120	-
Cl-5.1, Table-2 (Head and Handle)(Si)	-	120	-
Cl-5.1, Table-2 (Head and Handle)(Mn)	-	120	-
Cl-5.1, Table-2 (Head and Handle)(S)	-	120	-
Cl-5.1, Table-2 (Head and Handle)(P)	-	120	-
Cl-5.1, Table-2 (Head and Handle)(Cr)	-	120	-
Cl-5.1, Table-2 (Head and Handle)(V)	-	120	-
Cl-5.2, Table-3 (Rivets) (i)(Material- Chrome steel)	-	720	-
Cl-5.2, Table-3 (Rivets) (ii)(Material-Carbon steel)	-	600	-
Cl-5.2, Table-3 (Rivets)(C)	-	120	-
Cl-5.2, Table-3 (Rivets)(Si)	-	120	-
Cl-5.2, Table-3 (Rivets)(Mn)	-	120	-
Cl-5.2, Table-3 (Rivets)(S)	-	120	-
Cl-5.2, Table-3 (Rivets)(S)	-	120	-
Cl-5.2, Table-3 (Rivets)(P)	-	120	-
Cl-5.2, Table-3 (Rivets)(Cr)	-	120	-
Cl-5.2, Table-3 (Rivets)(V)	-	120	-
Cl-5.2, Table-3 (Rivets)(V)	-	120	-
Cl-6(Insulated handles)	-	500	-
Cl-7.1 (b)(Cutting edges (anywhere up to 2 mm from tip)	-	500	-
Cl-7.1 (c)(Rivet head any side)	-	500	-
Cl-7.2(Hardness of pliers)	-	400	-
Cl-8.1.1(Hard Wire Cutting Test)	-	500	-
Cl-8.1.2(Soft Wire Cutting Test)	-	200	-
Cl-8.2(Tube Gripping Test)	-	500	-
Cl-8.3(Shock Test)	-	500	-
Cl-8.4(Torsion Test)	-	500	-
Cl-8.4.2(Test Piece for Torsion Test)	-	500	-
Cl-8.5(Handle Load Test)	-	500	-
Cl-8.5.1(Test Piece for Handle Load Test)	-	500	-
Cl-8.6(Bend Test)	-	500	-
Cl-8.7(Insulation Test)	-	500	-
Cl-11.1(Marking)	-	200	-

17 Feb, 2028

-
Included w.e.f-18.08.2026

IS 4003 (Part 1) (2026)

Pipe Wrenches - Specification Part 1 General Purpose(Third revision)

All Grade / Type / Size / Designation as per IS 4003-1

10740 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4, Table-1(Dimensions-Nominal Size)	-	1200	-
Cl-4, Table-1(Dimensions-Capacity for suitable Pipe Diameter (D))	-	1200	-
Cl-4, Table-1(Dimensions-Jaw Thickness)	-	1200	-
Cl-4, Table-1(Dimensions-Approximate Length of Movable Jaw)	-	1200	-
Cl-4, Table-1(Dimensions-Approximate Length of Handle L2)	-	1200	-
Cl-4, Table-1(Dimensions-Width of Nut)	-	1200	-
Cl-5, Table-2 (i)(Handle and shank of movable jaw)	-	1200	-
Cl-5, Table-2 (ii)(Frame)	-	500	-
Cl-5, Table-2 (iii)(Leaf/conical coil spring)	-	500	-
Cl-5, Table-2 (iv)(Adjusting nut)	-	500	-
Cl-5, Table-2 (v)(Hinge pin)	-	500	-
Table-3(C)	-	120	-
Table-3(Si)	-	120	-
Table-3(Mn)	-	120	-
Table-3(S, Max)	-	120	-
Table-3(P)	-	120	-
Table-3(Cr)	-	120	-
Table-3(V)	-	120	-
Cl-6(HARDNESS)	-	800	-
Cl-7(MANUFACTURE)	-	1500	-
Cl-8(WORKMANSHIP AND FINISH)	-	500	-
Cl-11.1(Static Load Test)	-	2000	-
Cl-11.2(Static-Shock Load Test)	-	2000	-
Cl-13(Marking)	-	200	-

17 Feb, 2028

-
included w.e.f 04.08.2026

IS 4003 (Part 2) (2026)

Pipe Wrenches Specification Part 2 Heavy Duty (Second Revision)

All Grade / Type / Size / Designation as per IS 4003-2

8660 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4, Table-1(Dimensions-Nominal Size, L)	-	1200	-
Cl-4, Table-1(Dimensions-Capacity for suitable Pipe Diameter (D))	-	1200	-
Cl-4, Table-1(Dimensions-Jaw Thickness)	-	1200	-
Cl-4, Table-1(Dimensions-Length of Movable Jaw, L1)	-	1200	-
Cl-4, Table-1(Dimensions-Approximate Length of Handle L2)	-	1200	-
Cl-4, Table-1(Dimensions-Width of Nut)	-	1200	-
Cl-5, Table-2 (i)(Handle)	-	1200	-
Cl-5, Table-2 (ii)(Springs)	-	1500	-
Cl-5, Table-2 (iii)(Movable and heel Jaw)	-	1500	-
Cl-5, Table-2 (iv)(Shank of movable Jaw)	-	1500	-
Cl-5, Table-2 (v)(Adjusting nut)	-	1500	-
Table-3(C)	-	120	-
Table-3(Si)	-	120	-
Table-3(Mn)	-	120	-
Table-3(S, Max)	-	120	-
Table-3(Frame)	-	600	-
Table-3(Cr)	-	120	-
Table-3(V)	-	120	-
Table-3(Mo)	-	120	-
Cl-6(HARDNESS)	-	1200	-
Cl-7(MANUFACTURE)	-	1500	-
Cl-8(WORKMANSHIP AND FINISH)	-	500	-
Cl-11.1(Static Load Test)	-	2000	-
Cl-13(Marking)	-	200	-

17 Feb, 2028

-
Included w.e.f-18.08.2026

IS 2029 (2026)

RING WRENCHES (SPANNERS) SPECIFICATION (Fifth Revision)

All Grade / Type / Size / Designation as per IS 2029

4140 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1(Cranked Double-Ended Ring Wrenches (Spanners))	-	1200	-
Cl-3.2(Ring wrenches (spanners))	-	1200	-
Cl-3.1(Straight and Angled Double-Ended Ring Wrenches (Spanners))	-	1200	-
Cl-3.1(Double-Ended Offset Ring Wrenches (Spanners))	-	1200	-
Cl-3.1(Double-Headed, Flat and Offset Box Wrenches (Spanners))	-	1200	-
Cl-3.1(Double-Headed Deep Offset and Modified Offset Box Wrenches (Spanners))	-	1200	-
Cl-4, Table-6 (i)(Chrome vanadium)	-	840	-
Cl-4, Table-6 (ii)(40 Cr)	-	600	-
Cl-4, Table-6 (iii)(Medium carbon)	-	600	-
Cl-4, Table-6(C)	-	120	-
Cl-4, Table-6(Si)	-	120	-
Cl-4, Table-6(Mn)	-	120	-
Cl-4, Table-6(S)	-	120	-
Cl-4, Table-6(P)	-	120	-
Cl-4, Table-6(Cr)	-	120	-
Cl-4, Table-6(V)	-	120	-
Cl-5.1(Hardness)	-	400	-
Cl-5.2(Hardness)	-	400	-
Cl-6 (a)(Workmanship and Finish)	-	500	-
Cl-6 (b)(Anti-corrosive coating)	-	500	-
Cl-6 (c)(Torque Testing)	-	500	-
Cl-8(Marking)	-	200	-

17 Feb, 2028

-
Included w.e.f-18.08.2026

IS 2028 (2026)

Open Jaw Wrenches (Spanners) Specification ( Sixth Revision )

All Grade / Type / Size / Designation as per standard

4140 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1 & 3.7(Single-Ended Open Jaw Wrenches (Spanners) for General Purposes (Torque Series C or Series D))	-	1200	-
Cl-3.2 & 3.7(Double-Ended Open Jaw Wrenches (Spanners) for Automobile Use (Torque Series C or Series D))	-	1200	-
Cl-3.3 & 3.7(Alternate Dimensions Double-Ended Open Jaw Wrenches (Spanners) for General Purposes (Torque Series C or Series D))	-	1200	-
Cl-3.4 & 3.7(Double-Ended Open Jaw Wrenches (Spanners) for General Purposes (Torque Series C or Series D))	-	1200	-
Cl-3.5 & 3.7(Double-Headed Open-Ended Engineers’ Wrenches (Spanners) ISO Series (Torque Series C or Series D))	-	1200	-
Cl-4, Table-6 (i)(Chrome vanadium)	-	840	-
Cl-4, Table-6 (ii)(40 Cr)	-	720	-
Cl-4, Table-6 (iii)(Medium carbon)	-	600	-
Cl-4, Table-6(C)	-	120	-
Cl-4, Table-6(Si)	-	120	-
Cl-4, Table-6(Mn)	-	120	-
Cl-4, Table-6(S)	-	120	-
Cl-4, Table-6(Cr)	-	120	-
Cl-4, Table-6(V)	-	120	-
Cl-5(Hardness)	-	400	-
Cl-6 (b)(Plating Thickness)	-	400	-
Cl-8(Torque testing)	-	500	-
Cl-11(Marking)	-	200	-
Cl-6 (a)(workmanship and finish)	-	1000	-
Cl-3.1 & 3.7(Single-Ended Open Jaw Wrenches (Spanners) for General Purposes (Torque Series C or Series D))	-	0	-
Cl-3.2 & 3.7(Double-Ended Open Jaw Wrenches (Spanners) for Automobile Use (Torque Series C or Series D))	-	0	-
Cl-3.3 & 3.7(Alternate Dimensions Double-Ended Open Jaw Wrenches (Spanners) for General Purposes (Torque Series C or Series D))	-	0	-
Cl-3.4 & 3.7(Double-Ended Open Jaw Wrenches (Spanners) for General Purposes (Torque Series C or Series D))	-	0	-
Cl-3.5 & 3.7(Double-Headed Open-Ended Engineers’ Wrenches (Spanners) ISO Series (Torque Series C or Series D))	-	0	-
Cl-4, Table-6 (i)(Chrome vanadium)	-	0	-
Cl-4, Table-6 (ii)(40 Cr)	-	0	-
Cl-4, Table-6 (iii)(Medium carbon)	-	0	-
Cl-4, Table-6(C)	-	0	-
Cl-4, Table-6(Si)	-	0	-
Cl-4, Table-6(Mn)	-	0	-
Cl-4, Table-6(S)	-	0	-
Cl-4, Table-6(Cr)	-	0	-
Cl-4, Table-6(V)	-	0	-
Cl-5(Hardness)	-	0	-
Cl-6 (b)(Plating Thickness)	-	0	-
Cl-8(Torque testing)	-	0	-
Cl-11(Marking)	-	0	-
Cl-6 (a)(workmanship and finish)	-	0	-

17 Feb, 2028

-
included w.e.f 04.08.2026

IS 13352 (1992)

Stock for forgings produced from continuously cast blooms, billets and slabs - Specification

All Grade / Type / Size / Designation as per IS 13352

56010 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General requirements)	-	0	-
5(Freedom from defects)	-	500	-
6.1, table 2 (2)(C)	-	1460	C, SI, Mn, P, S,=100/PER ELEMENT Ni, Cr, Mo, Cu, V, B, Ti, Sn, Al= 120/ PER ELEMENT
6.1, table 2 (3)(Mn)	-	0	-
6.1, table 2 (4)(Si)	-	0	-
6.1, table 2 (5)(Ni)	-	0	-
6.1, table 2 (6)(Cr)	-	0	-
6.1, table 2 (7)(Mo)	-	0	-
6.1, table 2 (8)(V)	-	0	-
6.1, table 2 (9)(Al)	-	0	-
6.1, table 3 (1)(Carbon Silicon Manganese Nickel Chromium Molybdenum Vanadium Sulphur Phosphorus)	-	0	-
7(Mechanical properties)	-	14300	Upto 100 mmdia or RCS =3900/- Upto 101 to 200 mm dia or RCS = 5900 Upto 201to 250 mm dia or RCS = 6900/- For impact test Upto 100 mmdia or RCS =4000 per set 101 to 200 mm dia or RCS = 6000 per set 201 to 250 mm dia or RCS = 7000 per set
8(Grain size)	-	1150	-
9.1(Surface defects)	-	6000	-
9.2(Seams)	-	7500	UT= 1000/- Blank hardening =6000/- Microstructure= 500/-
10.1(Inclusion rating of the steel)	-	400	-
10.2(Step down test & magnetic particle test)	-	5000	-
11(Hardenability)	-	9000	sample Up to 34-100 mm dia or RCS =7000/- Up to 101 to 200 mm dia or RCS = 8000/- Up to 201 to 250 mm dia or RCS = 9000/-
12(Dimensions and Tolerances)	-	1200	-
14(Retest)	-	9500	Blue Fracture Test Upto 90 mmdia or RCS =7500/- Upto 91 to 150 mm dia or RCS = 8500 Upto 151 to 250 mm dia or RCS = 9500
16(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f.28.07.2025

IS 6149 (1984)

Specification for single - Ended open - Jaw adjustable wrenches (First Revision)

All Grade, Type, Size and Designation

6840 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 Table-1(Dimensions- Nominal Size)	-	1200	-
4 Table-1(Dimensions- a)	-	0	--
4 Table-1(Dimensions- b)	-	0	--
4 Table-1(Dimensions- t)	-	0	--
4 Table-1(Dimensions- d)	-	0	--
4 Table-1(Dimensions- Opening of adjustable jaws)	-	0	--
6(Hardness- Frame, handle and Jaw)	-	3560	Hardness= 400 Coating Thickness- 460 Adhesion Test- 200 Corrosion Resistance- 2000 Workmanship=500
8(Longitudinal Play of Adjustable Jaw)	-	300	---
8(Transverse Play of Adjustable Jaw)	-	300	---
8(Torque)	-	500	---
5(Chemical Composition)	-	980	-

17 Feb, 2028

-
-

IS 4003 : Part 1 (2024)

Pipe Wrenches - Specification Part 1 General Purpose(Second revision)

All Grade / Type / Size / Designation as per IS 4003 (Pt-1): 2024

15570 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 4.0(Dimensions)	-	1200	-
Clause.5.0(Carbon)	-	100	-
Clause.5.0(Sulphur)	-	100	-
Clause.5.0(Phosphorus)	-	100	-
Clause.5.0(Niobium)	-	0	-
Clause.5.0(Vanadium)	-	120	-
Clause.5.0(Nickel)	-	0	-
Clause.5.0(Molybdenum)	-	0	-
Clause.5.0(Chromium)	-	120	-
Clause.5.0(Silicon)	-	100	-
Clause.5.0(Manganese)	-	100	-
Clause.6.0(Hardness)	-	400	-
Clause.7.0(Manufacture)	-	0	-
Clause.7.1(Handle)	-	0	-
Clause.7.2(Movable Jaws)	-	0	-
Clause.7.3(Adjusting Nut)	-	0	-
Clause.7.4(Frame)	-	8730	Test as per IS 1865 Mech. Properties=3900/- + Impact tests= 4000/- + Brinell Hardness Test= 250 = 8730/- Test as per IS 14329 Freedom from defect= 580/- Mech. Properties = 3900/- Brinell Hardness = 250 Total= 4730
Clause.7.5(Hinge Pin)	-	0	-
Clause.7.6(Spring)	-	0	-
Clause.8.0(Workmanship & finish)	-	500	-
Clause.9.0(Operation)	-	0	-
Clause.10.0(Sampling)	-	0	-
Clause.11.0(Tests)	-	0	-
Clause.11.1(Static Load Test)	-	2000	-
Clause.11.2(Static-Shock Load Test)	-	2000	-
Clause.12.0(Designation)	-	0	-
Clause.13(Marking)	-	0	-15570

17 Feb, 2028

-
Included w.e.f.28.07.2025

IS 3757 (1985)

Specification for high strength structural bolts (Second Revision)

All Grade / Type / Size / Designation as per IS 3757.

24380 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2 Table-1,2(Dimensions- d)	-	1200	-
2 Table-1,2(Dimensions- p)	-	0	-
2 Table-1,2(Dimensions- bref)	-	0	-
2 Table-1,2(Dimensions- c)	-	0	-
2 Table-1,2(Dimensions- da)	-	0	-
2 Table-1,2(Dimensions- ds)	-	0	-
2 Table-1,2(Dimensions- dw)	-	0	-
2 Table-1,2(Dimensions- e)	-	0	-
2 Table-1,2(Dimensions- k)	-	0	-
2 Table-1,2(Dimensions- kw)	-	0	-
2 Table-1,2(Dimensions- r)	-	0	-
3 Table-1,2(Dimensions- s)	-	0	-
4 Table-1,2(Dimensions- z)	-	0	-
5 Table-1,2(Dimensions- ls)	-	0	-
6 Table-1,2(Dimensions- lg)	-	0	-
6 Table-1,2(Dimensions- l)	-	0	-
6 Table-1,2(Dimensions- Angle)	-	0	-
2.3(Conformity of threads)	-	0	-
4(Tensile Test for Machined Test pc- Stress at 0.2% non-propotional elongation)	-	3900	-
4(Tensile Test for Machined Test pc- Tensile Strength)	-	0	-
4(Tensile Test for Machined Test pc- Elongation)	-	0	-
4(Tensile Test for Machined Test pc- Reduction area)	-	0	-
4(Tensile test for full size bolt- Ultimate Tensile Strength)	-	0	-
4(Tensile test for full size bolt- Vicker's Hardness)	-	250	-
4(Tensile test for full size bolt- Breaking Position)	-	0	-
4(Proof load test)	-	1750	-
4(Wedge Load Test)	-	1750	-
4(Head soundness test)	-	350	-
4(Torsional test)	-	350	-
4(Surface Integrity Test )	-	0	-
4(Impact Test)	-	4000	-
4(Hardness test )	-	0	-
4(Decarburization test)	-	350	-
4(Surface discountinuties test)	-	580	-
4(Retempering test)	-	1150	-
5.1(Finish)	-	5770	Rs. 770 for finish test Rs. 5000 for hydrogen Embrittlement test
5.2(Galvanization- Uniformity of Zinc Coating)	-	580	-
5.2(Galvanization - Mass of zinc coating)	-	580	-
5.2(Galvanization - Passivation Test)	-	1240	-
5.2(Galvanization - Adhesion of Zinc Coating)	-	580	-
5.2(Galvanization - Adhesion of Zinc Coating)	-	580	-
5.2(Galvanization - Adhesion of Zinc Coating)	-	580	-

17 Feb, 2028

-
Included w.e.f.11.06.2025

IS 4508 (2024)

OPEN ENDED SLUGGING WRENCHES ( SPANNERS ) - SPECIFICATION ( Second Revision )

All Grade / Type / Size / Designation as per IS 4508:2024

3550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimensions)	-	1200	-
Clause.4.0(Carbon)	-	100	-
Clause.4.0(Sulphur)	-	100	-
Clause.4.0(Phosphorus)	-	100	-
Clause.4.0(Nickel)	-	120	-
Clause.4.0(Molybdenum)	-	120	-
Clause.4.0(Chromium)	-	120	-
Clause.4.0(Silicon)	-	100	-
Clause.4.0(Manganese)	-	100	-
Clause.5.0(Hardness)	-	250	-
Clause.6.0(Manufacture,Workmanship & finish)	-	500	-
Clause.7.0(Preservation & packing)	-	500	-
Clause.8.0(Sampling)	-	120	-
Clause.9.0(Designation)	-	120	-
Clause.10.0(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f.10.06.2025

IS 4509 (2024)

RING SLUGGING WRENCHES (SPANNERS) â SPECIFICATION (second revision)

All Grade / Type / Size / Designation as per IS 4509:2024

7440 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimensions)	-	1600	-
Clause.4.0(Carbon)	-	100	-
Clause.4.0(Sulphur)	-	250	-
Clause.4.0(Phosphorus)	-	250	-
Clause.4.0(Niobium)	-	0	-
Clause.4.0(Vanadium)	-	120	-
Clause.4.0(Nickel)	-	0	-
Clause.4.0(Molybdenum)	-	0	-
Clause.4.0(Chromium)	-	120	-
Clause.4.0(Silicon)	-	100	-
Clause.4.0(Manganese)	-	100	-
Clause.5.0(Hardness)	-	800	-
Clause.6.0(Manufacture ,Workmanship & finish)	-	4000	-
Clause.7.0(Preservation & packing)	-	0	-
Clause.8.0(Sampling)	-	0	-
Clause.9.0(Designation)	-	0	-
Clause.10.0(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f.30.05.2025

IS 4378 : Part 1 (2017)

Pliers and nippers: Part 1 diagonal cutting nippers - Dimensions and tests values (Third Revision)

All Grade / Type / Size / Designation as per IS 4378 (Pt-1):2017

4480 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Diagonal cutting nippers for hard wire)	-	700	-
3.2(Diagonal cutting nippers for medium hard wire)	-	3780	-
3.3(Toggle lever assisted side cutting nippers for hard wire)	-	0	-
4(Designation)	-	0	-
5(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f.30.05.2025

IS 4378 : Part 2 (2018)

Pliers and nippers: Part 2 end cutting nippers - Dimensions and test values (Third Revision)

All Grade / Type / Size / Designation as per IS 4378 (Pt-II)

4480 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(End cutting nippers for hard wire)	-	580	-
3.2(End cutting nippers for medium hard wire)	-	3900	-
3.3(Toggle lever assisted end cutting nippers for hard wire)	-	0	-
4(Designation)	-	0	-
5(Marking)	-	0	-
3.1(End cutting nippers for hard wire)	-	0	-
3.2(End cutting nippers for medium hard wire)	-	0	-
3.3(Toggle lever assisted end cutting nippers for hard wire)	-	0	-
4(Designation)	-	0	-
5(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f.30.05.2025

IS 1930 (2003)

Woodworking tools - Chisels and gouges (Third Revision)

All Grade / Type / Size / Designation etc. as per IS 1930

5450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Firmer chisels with tang, bevelled and plain (long type))	-	690	-
3.2(Butt chisels with tang, bevelled and plain (short type))	-	0	-
3.3(Firmer gouges)	-	0	-
4.1.1(Material)	-	500	-
4.1.2(Cutting edge)	-	0	-
4.1.3(Bolster and neck)	-	0	-
4.1.4(Tang)	-	0	-
4.1.5(Finish)	-	500	-
4.2.1(Shape(Handle))	-	0	-
4.2.2(Material (Handle))	-	0	-
4.2.3(Handle fixing to blade (Handle))	-	500	-
5.1.1(Test for soundness)	-	580	-
5.1.2(Bending test (chisels))	-	500	-
5.2(Test for strength of handle)	-	2180	Blade Hardness = 250/- Handle strength= 350/- Proof Load= 580/- Proof Torque= 1000/-

17 Feb, 2028

-
Included w.e.f.30.05.2025

IS 4432 (1988)

Specification for case hardening steels (First Revision)

All Grade/Type/Size/Designation as per IS 4432

40180 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
TABLE-1 (Clause-5)( CARBON)	-	100	-
TABLE-1 (Clause-5)(SULPHUR)	-	100	-
TABLE-1 (Clause-5)(PHOSPHURS)	-	100	-
TABLE-1 (Clause-5)(MANGANESE)	-	100	-
TABLE-1 (Clause-5)(SILICON)	-	100	-
TABLE-1 (Clause-5)( ALUMINIUM)	-	120	-
TABLE-1 (Clause-5)(Chromium)	-	120	-
TABLE-1 (Clause-5)(Molybdenum)	-	120	-
TABLE-1 (Clause-5)(NIOBIUM)	-	120	-
TABLE-1 (Clause-5)(VANADIUM)	-	120	-
TABLE-1 (Clause-5)(TITANIUM)	-	120	-
Cl. 5(Copper)	-	360	Copper = 120/- Nickle= 120/- Tin= 120/-
11(Dimensional Tolerances)	-	1200	-
4(Freedom from Defects)	-	500	-
7(Hardness)	-	400	-
8(Mechanical testing)	-	4200	-
8.4(Impact testing)	-	4000	-
9(Grain Size)	-	400	-
10(Inclusion rating)	-	400	-
14(Additional test)	-	26000	Blank Hardening- Rs. 6000/- Hot upset test -Rs. 6000/- Hardenability test- 5000/- Blue fracture test - 4500/- Microstructure- 500/- Macro etch test - 1000/- Step machined test- 1000/- MPI testing - 1000/- UT- 1000/-
TABLE-1 (Clause-5)(NITROGEN)	-	1500	-

17 Feb, 2028

-
-

IS 704 (1984)

Specification for crow - Bars and claw - Bars (Second Revision)

All Grade/Type/Size/Designationasper IS704:1984 RA 2021

5440 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 Table-1 to 9(Shapes And Dimensions-Width across flats )	-	1200	-
6(Hardness)	-	400	-
7(Manufacture and Finish)	-	500	-
8.1(Drop Test)	-	500	-
8.2(Static Load Test)	-	1000	-
8.3(Falling weight test)	-	500	-
5.0(Material testing)	-	0	-

17 Feb, 2028

-
-

IS 274 : Part 1 and 2 (1981)

Specification for shovels: Part 1 genral purpose shovels: Part 2 heat - Treated shovels (Third Revision)

All Grade/Type/Size/Designation per the IS 274 (Pt 1&2)

8200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Sulphur)	-	200	- S = Rs.100/- per element (As per IS 274 Part-I) - S = Rs.100/- per element (As per IS 274 Part-II)
4.1(Phosphorus)	-	200	- P = Rs.100/- per element (As per IS 274 Part-I) - P = Rs.100/- per element (As per IS 274 Part-II)
5 Table-1,2(Shape)	-	2400	Rs. 1200/- as per IS 274 (Part-I) Rs. 1200/- as per IS 274 (Part-II)
5 Table-1,2(Dimensions- A)	-	0	-
5 Table-1,2(Dimensions- B)	-	0	-
5 Table-1,2(Dimensions- C)	-	0	-
5 Table-1,2(Dimensions- D)	-	0	-
5 Table-1,2(Dimensions- E)	-	0	-
5 Table-1,2(Dimensions- G)	-	0	-
5 Table-1,2(Dimensions- H)	-	0	-
5 Table-1,2(Dimensions- K)	-	0	-
5 Table-1,2(Dimensions- L)	-	0	-
6.1(Blade thickness)	-	0	-
7.0(Mass)	-	0	-
8.0(Manufacture)	-	0	-
8.0(Manufacture)	-	0	-
8.0(Manufacture)	-	0	-
9.1(Handles)	-	0	-
9.3(Handles)	-	0	-
11.0(Workmanship & Finish )	-	1000	Rs. 500/- as per IS 274 (Part-I) Rs. 500/- as per IS 274 (Part-II)
12.0(Preservative Treatment )	-	0	-
14.2(Bending Test)	-	0	-
14.3(Flexing Test)	-	0	-
4.1(Sulphur)	-	0	-
4.1(Phosphorus)	-	0	-
5 Table-1,2(Shape)	-	0	-
5 Table-1,2(Dimensions- A)	-	0	-
5 Table-1,2(Dimensions- B)	-	0	-
5 Table-1,2(Dimensions- C)	-	0	-
5 Table-1,2(Dimensions- D)	-	0	-
5 Table-1,2(Dimensions- E)	-	0	-
5 Table-1,2(Dimensions- G)	-	0	-
5 Table-1,2(Dimensions- H)	-	0	-
5 Table-1,2(Dimensions- K)	-	0	-
5 Table-1,2(Dimensions- L)	-	0	-
6.1(Blade thickness)	-	0	-
7.0(Mass)	-	0	-
8.0(Manufacture)	-	0	-
8.0(Manufacture)	-	0	-
8.0(Manufacture)	-	0	-
9.1(Handles)	-	400	Hardness As per IS 274 (Part-II) Clause no. 9.0
9.3(Handles)	-	0	-
11.0(Workmanship & Finish )	-	500	-
12.0(Preservative Treatment )	-	0	-
14.2(Bending Test)	-	1000	Rs. 1000/- as per IS 274 (Part-I) Rs. 1000/- as per IS 274 (Part-II)
14.3(Flexing Test)	-	1000	Rs. 1000/- as per IS 274 (Part-I) Rs. 1000/- as per IS 274 (Part-II)
4.0(PHOSPHORUS)	-	0	-
4.0(SULPHUR)	-	0	-

17 Feb, 2028

-
-

IS 4003 : Part 1 (1978)

Specification for pipe wrenches: Part 1 general purpose (First Revision)

All Grade/Type/Size/Designation per IS 4003-1:2024

13520 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions- Nominal Size)	-	1200	-
4 AND AS PER IS 1570 PART 4(CARBON)	-	6620	-
4 AND AS PER IS 1570 PART 2(SULPHUR)	-	0	-
4 AND AS PER IS 1570 PART 2(PHOSPHORUS)	-	0	-
4 AND AS PER IS 1570 PART 2(MANGANESE)	-	0	-
4 AND AS PER IS 1570 PART 4(SILICON)	-	0	-
4 AND AS PER IS 1570 PART 4(CHROMIUM)	-	0	-
5(Hardness- Jaws)	-	1200	-
7(Workmanship & Finish)	-	500	-
13.1(Static Load Test)	-	2000	-
5(Hardness- Shank of movable Jaw)	-	0	-
4 AND AS PER IS 1570 PART 4(ALUMINIUM)	-	0	-
4 AND AS PER IS 1570 PART 4(VANADIM)	-	0	-
4 AND AS PER IS 1570 PART 4(BORON)	-	0	-
4 AND AS PER IS 1570 PART 4(NICKEL)	-	0	-
3(Dimensions-Minimum capacity)	-	0	-
3(Dimensions-Maximum capacity, D)	-	0	-
3(Dimensions- Jaw Thickness,T min)	-	0	-
3(Dimensions- Length of movablejae, l1)	-	0	-
3(Dimensions- Length of Handle, l2)	-	0	-
3(Dimensions- Width of Nut, N)	-	0	-
5(Hardness- Handle of movable Jaw)	-	0	-
6.1(Manufacture- Handel)	-	0	-
6.1(Manufacture- Handel)	-	0	-
6.2(Manufacture- Movable Jaw)	-	0	-
6.2(Manufacture- Movable Jaw)	-	0	-
6.2(Manufacture- Movable Jaw)	-	0	-
6.3(Manufacture- Adjusting Nut)	-	0	-
6.3(Manufacture- Adjusting Nut)	-	0	-
6.4(Manufacture- Frame)	-	0	-
6.5(Manufacture- Hinge Pin)	-	0	-
6.6(Manufacture- Spring)	-	0	-
6.6(Manufacture- Spring)	-	0	-
6.6(Manufacture- Spring)	-	0	-
7(Workmanship & Finish)	-	0	-
7(Workmanship & Finish)	-	0	-
8(Operation)	-	0	-
8(Operation)	-	0	-
13.1(Static Load Test)	-	0	-
13.2(Static- Shock Load Test)	-	2000	-
13.2(Static- Shock Load Test)	-	0	-
4 AND AS PER IS 1570 PART 4(MOLYBDENUM)	-	0	-
4 AND AS PER IS 1570 PART 4(MANGANESE)	-	0	-
4 AND AS PER IS 1570 PART 2(CARBON)	-	0	-

17 Feb, 2028

-
-

IS 844 : Part 3 (1979)

Specification for screw drivers: Part 3 dimensions for screw drivers for recessed head screws (Second Revision)

AllGrade/Type/Size/Designation as per IS 844 (Part-III)

3840 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 Table 1 & 2(Torque Test)	-	500	-
4(Hardness)	-	400	-
3 , IS 844 (P- 1)(Finish)	-	1000	Finish Coating
3 , IS 844 (P- 1)(Coating)	-	740	- C, Si, Mn, S, P -100/ element= 500/- - Cr, V - 120/element = Rs. 240/-
2.1( Dimension, d1)	-	1200	For complete dimensional inspection
2.4(h)	-	0	-
2.4(l)	-	0	-
2.3(S)	-	0	-
2.2( Dimension, d)	-	0	-
2.1( Dimension, β)	-	0	-
2.1( Dimension, α)	-	0	-
2.1( Dimension, lmin)	-	0	-
2.1( Dimension, f)	-	0	-
2.1( Dimension, e)	-	0	-
2.1( Dimension, d2)	-	0	-

17 Feb, 2028

-
-

IS 7283 (1992)

Hot - Rolled bars for the production of bright bars and machined parts for engineering applications specification (First Revision)

All Grade / Type / Size / Designation as per IS 7283

11240 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Workmanship)	-	500	-
Cl 7(Diameter & Out Of Round)	-	1200	-
Cl 8(Decarburization)	-	400	-
Cl 9(Inclusion)	-	400	-
Cl 10(Hardenability)	-	7000	-
Cl 11(Size)	-	400	-
Cl 5(Material Test)	-	1340	-

17 Feb, 2028

-
-

IS 4003 : Part 2 (1986)

Specification for pipe wrenches: Part 2 heavy duty (First Revision)

All Grade/Type/Size/Designation per the IS 4003 (P-II)

9080 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions- Nominal Size)	-	1200	-
3(Dimensions-Capacity D min)	-	0	-
3(Dimensions- Capacity D max)	-	0	-
3(Dimensions- Jaw Thickness,T min)	-	0	-
3(Dimensions- Length of movablejae, l1)	-	0	-
3(Dimensions- Length of Handle, l2)	-	0	-
3(Dimensions- Width of Nut, N)	-	0	-
5(Hardness- Movable and heel Jaws)	-	400	-
5(Hardness- Shank of movable Jaw)	-	400	-
5(Hardness- Adjustable nut)	-	0	-
6.1(Manufacture- Handel)	-	0	-
6.1(Manufacture- Handel)	-	0	-
6.2(Movable Jaw)	-	0	-
6.2(Movable Jaw)	-	0	-
6.3(Heel jaw)	-	0	-
6.3(Heel jaw)	-	0	-
6.4(Adjusting Nut)	-	0	-
6.4(Adjusting Nut)	-	0	-
6.4(Adjusting Nut)	-	0	-
6.5(Springs)	-	0	-
6.5(Springs)	-	0	-
7(Workmanship & Finish)	-	500	-
7(Workmanship & Finish)	-	0	-
7(Workmanship & Finish)	-	0	-
7(Workmanship & Finish)	-	0	-
8(Operation)	-	0	-
8(Operation)	-	0	-
11.1(Static Load Test)	-	2000	-
11.1(Static Load Test)	-	0	-
4 AND AS PER IS 1570 PART 2(MANGANESE)	-	0	-
4 AND AS PER IS 1570 PART 2(PHOSPHORUS)	-	0	-
4 AND AS PER IS 1570 PART 2(SULPHUR)	-	0	-
4 AND AS PER IS 1570 PART 2(CARBON)	-	0	-
4 AND AS PER IS 4454 PART 1(MICRO ALLOY)	-	2340	0
4 AND AS PER IS 4454 PART 1(NITROGEN)	-	0	-
4 AND AS PER IS 4454 PART 1(cu + cr + ni)	-	0	-
4 AND AS PER IS 4454 PART 1(SULPHUR+ PHOSPHORUS)	-	0	-
4 AND AS PER IS 4454 PART 1(COPPER)	-	240	-
4 AND AS PER IS 4454 PART 1(PHOSPHORUS)	-	0	-
4 AND AS PER IS 4454 PART 1(SULPHUR)	-	0	-
4 AND AS PER IS 4454 PART 1(MANGANESE)	-	0	-
4 AND AS PER IS 4454 PART 1(SILICON)	-	0	-
4 AND AS PER IS 4454 PART 1(CARBON)	-	0	-
4 AND AS PER IS 2707(MICRO ALLOY)	-	0	-
4 AND AS PER IS 2707(SILICON)	-	400	-
4 AND AS PER IS 2707(MANGANESE)	-	400	-
4 AND AS PER IS 2707(PHOSPHORUS)	-	400	-
4 AND AS PER IS 2707(SULPHUR)	-	400	-
4 AND AS PER IS 2707(CARBON)	-	400	-

17 Feb, 2028

-
-

IS 841 (1983)

Specification for steel hammers (Second Revision)

All Grade/Type/Size/Designation as per IS 841

4140 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material Testing)	-	1340	-
4(Hardness Testing)	-	400	-
5(Dimensions)	-	1200	-
6(Mass)	-	200	-
9(Workmanship and finish)	-	500	-
10(Soundness and assembly test)	-	500	-

17 Feb, 2028

-
-

IS 3063 (1994)

Fasteners - Single coil rectangular section spring lock washers specification (Second Revision)

All Grade/Type/Size/Designation as per IS 3063

8140 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions & Tolerance)	-	1200	-
5(Material Testing)	-	740	-
11(Hardness (HV))	-	400	-
11.2(Permanent set test)	-	500	-
11.3(Permanent Load test)	-	4800	-
11.4(Twist test)	-	500	-

17 Feb, 2028

-
-

IS 4509 (1992)

Ring slugging wrenches (Spanners) - specification (First Revision)

Grade/Type/Size/Designation as per IS 4509

2840 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions- s)	-	1200	Rs. 1200/- for complete dimensional inspection.
3(Dimensions- a)	-	0	-
3(Dimensions- b)	-	0	-
3(Dimensions- l)	-	0	-
5(Hardness)	-	400	-
6(Workmanship and Finish)	-	500	-
4(Chemical Test)	-	740	- C, Si, Mn, S, P- Rs. 100/- per Element - Cr, V - Rs. 120/- per Element

17 Feb, 2028

-
-

IS 4072 (1975)

Specification for steel for spring washers (First Revision)

All Grade/Type/Size/Designation as per IS 4072

3340 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 2.1, 5.1, 5.2 Table 1 (Carbon)	-	100	-
Cl. 2.1, 5.1, 5.2 Table 1 (Silicon)	-	100	-
Cl. 2.1, 5.1, 5.2 Table 1 (Manganese)	-	100	-
Cl. 2.1, 5.1, 5.2 Table 1 (Sulphur)	-	100	-
Cl. 2.1, 5.1, 5.2 Table 1 (Phosphorous)	-	100	-
Cl. 2.1, 5.1, 5.2 Table 1 (Chromium)	-	120	-
Cl. 2.1, 5.1, 5.2 Table 1 (Vanadium)	-	120	-
6.2(DeCarburization)	-	900	-
7(Dimensions & Tolerance)	-	1200	-
8(Calculation of Weight)	-	500	-

17 Feb, 2028

-
-

IS 3748 (1990)

Tool and die steels - Specification (Second Revision)

All Grade/Type/Size/Designation as per IS 3748

14460 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1, 7.2, 12.1 & Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl 7.1, 7.2, 12.1 & Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl 7.1, 7.2, 12.1 & Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl 7.1, 7.2, 12.1 & Table 1(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl 7.1, 7.2, 12.1 & Table 1(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl 7.1, 7.2, 12.1 & Table 1(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl 7.1, 7.2, 12.1 & Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl 7.1, 7.2, 12.1 & Table 1(Tungsten- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl 7.1, 7.2, 12.1 & Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl 7.1, 7.2, 12.1 & Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl 7.1, 7.2, 12.1 & Table 1(Cobalt- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
6(Freedom from defects)	-	500	-
9.1(Hardness , max-IS 1500 )	-	400	-
10(Dimensions and Tolerances, mm)	-	1200	-
13(Ultra sound testing)	-	1000	-
14.5(v) Magnaflux test)	-	1000	-
14.3(iii)Macro etch test)	-	1000	-
14.6(vi) Metallographic test)	-	900	Microstructure - Rs. - 500/- Inclusion Rating = Rs. 400/-
14.7(vii) Diistribution of carbides)	-	500	-
14.1(i) Shephard's P.F.Test)	-	5500	-
14.2(ii)Fracture disc test)	-	500	-
14.4(iv)Crop test upto 45mm dia)	-	500	-
Cl 7.1, 7.2, 12.1 & Table 1(Tin- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-

17 Feb, 2028

-
-

IS 9516 (1980)

Specification for heat resisting steels

All Grade/Type/Size/Designation as per IS 9516

9100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1,5.2,5.3 Table 4(Carbon-Relevant parts of IS 228)	-	100	-
5.1,5.2,5.3 Table 4(Silicon-Relevant parts of IS 228)	-	100	-
5.1,5.2,5.3 Table 4(Manganese-Relevant parts of IS 228)	-	100	-
5.1,5.2,5.3 Table 4(Nickel-Relevant parts of IS 228)	-	120	-
5.1,5.2,5.3 Table 4(Chromium-Relevant parts of IS 228)	-	120	-
5.1,5.2,5.3 Table 4(Sulphur-Relevant parts of IS 228)	-	100	-
5.1,5.2,5.3 Table 4(Phosphorous-Relevant parts of IS 228)	-	100	-
5.3(Molybdenum-Relevant parts of IS 228)	-	120	-
5.3(Vanadium-Relevant parts of IS 228)	-	120	-
5.3(Copper-Relevant parts of IS 228)	-	120	-
4(FREEDOM FROM DEFECTS)	-	500	-
6, Table 2(i) Yield stess/.2% Proof stress, Mpa)	-	800	-
6, Table 2(ii)Ultimate Tensile Strength, Mpa)	-	3300	-
6, Table 2(iii)Elongation, %)	-	300	-
7(DIMENSIONS AND TOLERANCE)	-	1200	-
6, Table 2(iv) Hardness, HBW)	-	400	-
5.1,5.2,5.3 Table 4(Nitrogen-Relevant parts of IS 228)	-	1500	-

17 Feb, 2028

-
-

IS 3195 (1992)

Steel for the manufacture of volute and helical springs (For Railway Rolling Stock) - Specification (Third Revision)

Grade/Type/Size/Designation as per IS 3195

4260 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3, 6.1, 6.2 & Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 3, 6.1, 6.2 & Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 3, 6.1, 6.2 & Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 3, 6.1, 6.2 & Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 3, 6.1, 6.2 & Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 3, 6.1, 6.2 & Table 1(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl. 3, 6.1, 6.2 & Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl. 3, 6.1, 6.2 & Table 1(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
7(Hardness)	-	400	-
10(Freedom from defects)	-	500	-
8(Decarburisation)	-	400	-
9(Inclusion rating)	-	400	-
11( DIMENSIONS AND TOLERANCES)	-	1200	Dimensions & Tolerances= Rs. 1200/-
12(Calculation of mass)	-	500	-

17 Feb, 2028

-
-

IS 9550 (2001)

Bright steel bars - Specification (First Revision)

All Grade/Type/Size/Designation as per IS 9550

17740 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6(Parameter as per requiremnt of purchaser.)	-	1340	Charges for Chemical Composition.
7(Mechancial Properties)	-	10600	- Surface Roughness test = Rs. 300/- - Mechanical Testing (Ts, Ys, %el) - Rs. 3900/- - Hardenability = 5000/- - Inclusion rating = 400/- - Microstructure = 500/- - Depth of defect by microscope method - 500/-
9.1(Decarburisation)	-	400	- Decarburization = Rs. 400/-
8.1 and 8.2(Dimensions and Tolerances, mm)	-	1200	-
13(Surface Protection)	-	4200	- Grain Size- Rs. 400/- Radiography testing -800/- DPT - 1000/- UT -1000/- MPI -1000/-)

17 Feb, 2028

-
-

IS 4296 : Part 1 (2016)

Tools for pressing: Part 1 round punches with 60 degrees conical head and straight shank (Second Revision)

All Grade/Type/Size/Designation as per IS 4296-1

2820 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions & Tolerance)	-	1500	-
4(Material Testing)	-	1220	- C, Si, P, Mn, S - Rs. 100/- per element - Ni, Cr, V, Mo, Co, W - Rs. 120/- per element
6.2(Hardness (HRC))	-	400	-

17 Feb, 2028

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Institute for Auto Parts and Hand Tools Technology, Ludhiana

A-9, Phase-V, Focal Point, Ludhiana, Ludhiana, Ludhiana, Punjab, 141010

8427262400 iatldh@iapht.org

Scope List