BIS - LIMS (Laboratory Information Management System)

Institute for Auto Parts and Hand Tools Technology

A-9, Phase-V, Focal Point, Ludhiana, Ludhiana, Ludhiana, Punjab, 141010

8427262400 iatldh@iapht.org

Scope List

Reset

67 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 18509 (2024)

Cross-recessed Countersunk Head Wood Screws ï¿½ Specification

All Grade / Type / Size / Designation as per IS 18509 : 2024

19580 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 4.0(Dimenssions.)	-	580	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause. 5.0(Material)	-	1200	-
Clause. 5.0(Thread And Screw ends)	-	0	-
Clause. 5.0(Cross Recess)	-	0	-
Clause. 5.0(Tolerances)	-	0	-
Clause. 5.0(Surface Condition)	-	16530	-
Clause. 5.0(Surface Coating)	-	460	-
Clause. 5.0(Acceptability)	-	0	-
Clause.6.0(Torque Testing)	-	350	-
Clause.7.0(Hardness)	-	460	-
Clause.8.0(Designation)	-	0	-
Clause.9.0(Marking)	-	0	-
Clause. 4.0(Dimenssions.)	-	0	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause. 5.0(Material)	-	0	-
Clause. 5.0(Thread And Screw ends)	-	0	-
Clause. 5.0(Cross Recess)	-	0	-
Clause. 5.0(Tolerances)	-	0	-
Clause. 5.0(Surface Condition)	-	0	-
Clause. 5.0(Surface Coating)	-	0	-
Clause. 5.0(Acceptability)	-	0	-
Clause.6.0(Torque Testing)	-	0	-
Clause.7.0(Hardness)	-	0	-
Clause.8.0(Designation)	-	0	-
Clause.9.0(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f.03.03.2025

IS 18508 (2024)

Chipboard Screws ï¿½ Specification

All Grade / Type / Size / Designation as per IS 18508

19695 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 4.0(Dimenssions.)	-	695	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause. 5.0(Material)	-	1200	-
Clause. 5.0(Cross Recess)	-	0	-
Clause. 5.0(Tolerances)	-	0	-
Clause. 5.0(Surface Condition)	-	16530	-
Clause. 5.0(Surface Coating)	-	460	-
Clause.6.0(Acceptability)	-	0	-
Clause.6.0(Torque Testing)	-	350	-
CClause.7.0(Hardness)	-	460	-
Clause.8.0(Designation)	-	0	-
Clause.9.0(Marking)	-	0	-
Clause. 4.0(Dimenssions.)	-	0	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause. 5.0(Material)	-	0	-
Clause. 5.0(Cross Recess)	-	0	-
Clause. 5.0(Tolerances)	-	0	-
Clause. 5.0(Surface Condition)	-	0	-
Clause. 5.0(Surface Coating)	-	0	-
Clause.6.0(Acceptability)	-	0	-
Clause.6.0(Torque Testing)	-	0	-
CClause.7.0(Hardness)	-	0	-
Clause.8.0(Designation)	-	0	-
Clause.9.0(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f.03.03.2025

IS 18507 (2024)

Drywall Screws ï¿½ Specification

All Grade / Type / Size / Designation as per IS 18507: 2024

19580 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 4.0(Dimenssions.)	-	580	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause. 5.0(Material)	-	1200	-
Clause. 5.0(Cross Recess)	-	0	-
Clause. 5.0(Tolerances)	-	0	-
Clause. 5.0(Surface Condition)	-	15990	-
Clause. 5.0(Surface Coating)	-	1000	-
Clause. 5.0(Acceptability)	-	0	-
Clause.6.0(Torque Testing)	-	350	-
Clause.7.0(Hardness)	-	460	-
Clause.8.0(Designation)	-	0	-
Clause.9.0(Marking)	-	0	-
Clause. 4.0(Dimenssions.)	-	0	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause. 5.0(Material)	-	0	-
Clause. 5.0(Cross Recess)	-	0	-
Clause. 5.0(Tolerances)	-	0	-
Clause. 5.0(Surface Condition)	-	0	-
Clause. 5.0(Surface Coating)	-	0	-
Clause. 5.0(Acceptability)	-	0	-
Clause.6.0(Torque Testing)	-	0	-
Clause.7.0(Hardness)	-	0	-
Clause.8.0(Designation)	-	0	-
Clause.9.0(Marking)	-	0	-

17 Feb, 2028

-
-

IS 7486 (2018)

Raised countersunk head screws (Common Head Style) with type H or type Z cross recess - Product grade A (Third Revision)

All Grade / Type / Size / Designation as per IS 7486: 2018

16680 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	1270	-
4, table 2(Material)	-	1200	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	14210	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-
3(Dimensions)	-	0	-
4, table 2(Material)	-	0	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	0	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-
3(Dimensions)	-	0	-
4, table 2(Material)	-	0	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	0	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-

17 Feb, 2028

-
-

IS 7485 : Part 2 (2018)

Countersunk flat head screws (common head style) with type H or Type Z Cross Recess - Product Grade A part 2 Steel Screws of Property Class 8.8, Stainless Steel Screws and Non - Ferrous Metal Screws ( Third Revision)

All Grade / Type / Size / Designation as per IS 7485-2

21670 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	1270	-
4, table 2(Material)	-	1200	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	19200	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-
3(Dimensions)	-	0	-
4, table 2(Material)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	0	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-

17 Feb, 2028

-
-

IS 7485 : Part 1 (2018)

Countersunk Flat Head Screws (Common head Style) With Type H or Type Z Cross Recess - Product Grade A Part 1 Steel Screws of Property Class 4.8 ( Third Revision)

All Grade / Type / Size / Designation as per IS 7485-1

13940 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	1270	-
4, table 2(Material)	-	1200	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	11470	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-
3(Dimensions)	-	0	-
4, table 2(Material)	-	0	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	0	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-

17 Feb, 2028

-
Included w.e.f 03.06.2025

IS 7483 (2018)

Pan Head Screws With Type H or Type Z Cross Recess - Product Grade A (Third Revision)

All Grade / Type / Size / Designation as per IS 7483

19670 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	1200	-
4, table 2(Material)	-	1200	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	17270	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-
3(Dimensions)	-	0	-
4, table 2(Material)	-	0	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	0	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-
3(Dimensions)	-	0	-
4, table 2(Material)	-	0	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	0	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-
3(Dimensions)	-	0	-
4, table 2(Material)	-	0	-
4, table 2(General requirements)	-	0	-
4, table 2(Thread)	-	0	-
4, table 2(Mechanical property)	-	0	-
4, table 2(Tolerances)	-	0	-
4, table 2(Cross recess)	-	0	-
4, table 2(Finish - coating)	-	0	-
4, table 2(Surface integrity)	-	0	-
4, table 2(Acceptability)	-	0	-
5(Designation)	-	0	-

17 Feb, 2028

-
Included w.e.f 03.06.2025

IS 18476 (2023)

Fasteners ï¿½ Hexagon Washer Head Drilling Screws with Tapping Screw Thread

All Grade / Type / Size / Designation as per IS 18476

17225 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 4.0(Dimenssions.)	-	1385	-
Clause. 4.0(Thread size.)	-	0	-
Clause. 4.0(Length)	-	0	-
Clause. 5.0(Material)	-	1200	-
Clause. 5.0(Thread)	-	0	-
Clause. 5.0(Tolerances)	-	0	-
Clause. 5.0(Mechnical and functional properties.)	-	14640	-
Clause. 5.0(Finish)	-	0	-
Clause. 5.0(Acceptability)	-	0	-
Clause.6.0(Designation)	-	0	-
Clause.6.0(Marking)	-	0	-

17 Feb, 2028

-
-

IS 18471 : Part 3 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 3 Raised Countersunk Head

All Grade / Type / Size / Designation as per IS 18471 (Part-III)

17650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	810	-
Clause. 3.0(Thread size.)	-	0	-
Clause. 3.0(Length)	-	0	-
Clause. 4.0(Material)	-	1200	-
Clause. 4.0(Thread)	-	0	-
Clause. 4.0(Cross recesses)	-	0	-
Clause. 4.0(Tolerances)	-	0	-
Clause. 4.0(Mechnical and functional properties.)	-	15640	-
Clause. 4.0(Finish)	-	0	-
Clause. 4.0(Acceptability)	-	0	-
Clause.5.0(Designation)	-	0	-
Clause.5.0(Marking)	-	0	-

17 Feb, 2028

-
-

IS 18471 : Part 2 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 2 Countersunk Head

All grade/ Type/ Size as per IS 18471 (Part-II): 2023

17650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	810	-
Clause. 3.0(Thread size.)	-	0	-
Clause. 3.0(Length)	-	0	-
Clause. 4.0(Material)	-	1200	-
Clause. 4.0(Thread)	-	0	-
Clause. 4.0(Cross recesses)	-	0	-
Clause. 4.0(Mechnical and functional properties.)	-	15640	-
Clause. 4.0(Finish)	-	0	0
Clause. 4.0(Acceptability)	-	0	-
Clause.5.0(Designation)	-	0	-
Clause.5.0(Marking)	-	0	-

17 Feb, 2028

-
-

IS 18471 : Part 1 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 1 Pan Head

All grade, Type & Size as per IS 18471 -1

17650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	810	-
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Thread size.)	-	0	-
Clause. 3.0(Length)	-	0	-
Clause. 4.0(Material)	-	1200	-
Clause. 4.0(Thread)	-	0	-
Clause. 4.0(Cross recesses)	-	0	-
Clause. 4.0(Mechnical and functional properties.)	-	15640	-
Clause. 4.0(Finish)	-	0	-
Clause. 4.0(Acceptability)	-	0	-
Clause.5.0(Designation)	-	0	-
Clause.5.0(Marking)	-	0	-
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Thread size.)	-	0	-
Clause. 3.0(Length)	-	0	-
Clause. 4.0(Material)	-	0	-
Clause. 4.0(Thread)	-	0	-
Clause. 4.0(Cross recesses)	-	0	-
Clause. 4.0(Mechnical and functional properties.)	-	0	-
Clause. 4.0(Finish)	-	0	-
Clause. 4.0(Acceptability)	-	0	-
Clause.5.0(Designation)	-	0	-
Clause.5.0(Marking)	-	0	-
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Thread size.)	-	0	-
Clause. 3.0(Length)	-	0	-
Clause. 4.0(Material)	-	0	-
Clause. 4.0(Thread)	-	0	-
Clause. 4.0(Cross recesses)	-	0	-
Clause. 4.0(Mechnical and functional properties.)	-	0	-
Clause. 4.0(Finish)	-	0	-
Clause. 4.0(Acceptability)	-	0	-
Clause.5.0(Designation)	-	0	-
Clause.5.0(Marking)	-	0	0
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Thread size.)	-	0	-
Clause. 3.0(Length)	-	0	-
Clause. 4.0(Material)	-	0	-
Clause. 4.0(Thread)	-	0	-
Clause. 4.0(Cross recesses)	-	0	-
Clause. 4.0(Mechnical and functional properties.)	-	0	-
Clause. 4.0(Finish)	-	0	-
Clause. 4.0(Acceptability)	-	0	-
Clause.5.0(Designation)	-	0	-
Clause.5.0(Marking)	-	0	-
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Dimenssions.)	-	0	-
Clause. 3.0(Thread size.)	-	0	-
Clause. 3.0(Length)	-	0	-
Clause. 4.0(Material)	-	0	-
Clause. 4.0(Thread)	-	0	-
Clause. 4.0(Cross recesses)	-	0	-
Clause. 4.0(Mechnical and functional properties.)	-	0	-
Clause. 4.0(Finish)	-	0	-
Clause. 4.0(Acceptability)	-	0	0
Clause.5.0(Designation)	-	0	-
Clause.5.0(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f 03.06.2025

IS 15833 (2009)

Stainless Steel Tower Bolts -specification

Grade / Type / Size / Designation etc.

6780 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(DIMENSIONS)	-	1200	-
Cl 4(MATERIAL)	-	4580	-
Cl 7(0)	-	1000	Finish
Clause 4.2(Carbon Content)	-	0	-
Clause 4.2(Silicon)	-	0	-
Clause 4.2(Manganese)	-	0	-
Clause 4.2(nickel)	-	0	-
Clause 4.2(Chromium)	-	0	-
Clause 4.2(Sulphur)	-	0	-
Clause 4.2(Phosphorus)	-	0	-
Clause 4.2(Carbon Content)	-	0	-
Clause 4.2(Silicon)	-	0	-
Clause 4.2(Manganese)	-	0	-
Clause 4.2(nickel)	-	0	-
Clause 4.2(Chromium)	-	0	-
Clause 4.2(Sulphur)	-	0	-
Clause 4.2(Phosphorus)	-	0	-
Clause 4.2(Mech)(Phosphorus)	-	0	-
Clause 4.2(Mech)(Sulphur)	-	0	-
Clause 4.2(Mech)(Chromium)	-	0	-
Clause 4.2(Mech)(nickel)	-	0	-
Clause 4.2(Mech)(Manganese)	-	0	-
Clause 4.2(Mech)(Silicon)	-	0	-
Clause 4.2(Mech)(Carbon Content)	-	0	-
Cl 7(0)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 5(MANUFACTURE)	-	0	-
Cl 4(MATERIAL)	-	0	-
Cl 3(NOMINAL SIZES)	-	0	-
Cl 3(NOMINAL SIZES)	-	0	-
8(Marking)	-	0	-
Clause 4.2(Mech)(Phosphorus)	-	0	-
Clause 4.2(Mech)(Sulphur)	-	0	-
Clause 4.2(Mech)(Chromium)	-	0	-
Clause 4.2(Mech)(nickel)	-	0	-
Clause 4.2(Mech)(Manganese)	-	0	-
Clause 4.2(Mech)(Silicon)	-	0	-
Clause 4.2(Mech)(Carbon Content)	-	0	-
Cl 7(0)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 6(DIMENSIONS)	-	0	-
Cl 5(MANUFACTURE)	-	0	-
Cl 4(MATERIAL)	-	0	-
Cl 3(NOMINAL SIZES)	-	0	-
Cl 3(NOMINAL SIZES)	-	0	-
8(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f. 22.02.2024

IS 1284 (1975)

Specification for wrought aluminium alloy bolt and screw stock (for general engineering purposes) (Second Revision)

All Grade / Type / Size / Designation etc.as per std.

7340 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defects)	-	500	-
6(Dimensions and tolerances)	-	1200	-
8.1(Tensile test)	-	3600	-
8.2(Head-Forming test)	-	1000	-
4(Freedom from defects)	-	0	-
5.1 Table 1(Copper)	-	0	-
5.1 Table 1(Magnesium)	-	0	-
5.1 Table 1(Silicon)	-	0	-
5.1 Table 1(Iron)	-	0	-
5.1 Table 1(Manganese)	-	0	-
5.1 Table 1(Zinc)	-	0	-
5.1 Table 1(Titanium and/or other grain refining elements)	-	0	-
5.1 Table 1(Chromium)	-	0	-
5.1 Table 2(Diameter)	-	0	-
5.1 Table 2(0.2 percent proof stress)	-	0	-
5.1 Table 2(Tensile strength)	-	0	-
6(Dimensions and tolerances)	-	0	-
8.1(Tensile test)	-	0	-
8.2(Head-Forming test)	-	0	-
10(Marking)	-	0	-

17 Feb, 2028

-
Included w.e.f. 22.02.2024

IS 281 (2009)

Mild steel sliding door bolts for use with padlocks - Specification (Fourth Revision)

All Grade / Type / Size / Designation etc.as per Std.

3540 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6-Table 1(DIMENSIONS AND TOLERANCES-A)	-	1200	-
8.1(FINISH-Sliding Bolts, Plate Type)	-	1000	-
Cl. 8.1 (Ref. Cl.9 of IS 1868:1996)(Thickness Test for Copper Plating of Oxidized Finished Material, Cl. 4 of IS 1378 : 1987 & Cl 3 of IS 3203)	-	0	-
Cl. 8.2 (Ref. Cl.9 of IS 1868:1996)(Thickness Test for Copper Plating of Oxidized Finished Material, Cl. 4 of IS 1378 : 1987 & Cl 3 of IS 3203)	-	0	-
3(TYPES)	-	0	-
4(SIZES)	-	0	-
6(DIMENSIONS AND TOLERANCES-A)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-A)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-B)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-C)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-D)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-E)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-F)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-G)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-H)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-J)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-T)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 (IS 451))	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Rivets on bolts plates)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Rivets on Socket)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on bolt)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on Socket)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on Staple)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for plate and sockets)	-	0	-
6-Table 1(DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for Staple)	-	0	-
7.1(MANUFACTURE-General)	-	0	-
7.1(MANUFACTURE-General)	-	0	-
7.1(MANUFACTURE-General)	-	0	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	0	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	0	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	0	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	0	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	0	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	0	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	0	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	0	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	0	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	0	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	0	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	0	-
8.1(FINISH-Sliding Bolts, Plate Type)	-	0	-

17 Feb, 2028

-
Included w.e.f. 22.02.2024

IS 15834 (2020)

Stainless Steel Sliding Door Bolts ( Aldrops ) for Use With Padlocks - Specification ( First Revision )

All Grade/Type/Size/Designation etc. as per standard.

6780 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(DIMENSIONS AND TOLERANCES)	-	1200	-
Cl 7(FINISH)	-	1000	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 7(FINISH)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 5(DIMENSIONS AND TOLERANCES)	-	0	-
Cl 6(MANUFACTURE)	-	0	-
Cl 7(FINISH)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
5(DIMENSIONS AND TOLERANCES)	-	0	-
6(MANUFACTURE)	-	0	-
7(FINISH)	-	0	-
8(Marking)	-	0	-
8(Marking)	-	0	-
Cl.4(Carbon)	-	4580	Chemical Composition as per Clause No.4
Cl.4(Sulphur)	-	0	-
Cl.4(Phosphorus)	-	0	-
Cl.4(Manganese)	-	0	-
Cl.4(Silicon)	-	0	-
Cl.4(Nickel)	-	0	-
Cl.4(Chromium)	-	0	-
Cl.4(Copper)	-	0	-
Cl.4(Molybdenum)	-	0	-
Cl.4(Nitrogen)	-	0	-
Cl.4(Titanium)	-	0	-
Cl.4(Niobium)	-	0	-

17 Feb, 2028

-
-

IS 10238 (2001)

Fasteners - Threaded steel fasteners - Step bolts for steel structures - Specification (First Revision)

All Grade/Type/Size/Designation etc. standard

13300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(MECHANICAL PROPERTIES)	-	10600	Charges for all tests as per IS 1367-3 for Property class-4.6.
8.1(FINISH)	-	500	-
10.1.1(TESTS)	-	1000	Cantilever Test
5(MECHANICAL PROPERTIES)	-	0	-
8.1(FINISH)	-	0	-
10.1.1(TESTS)	-	0	-
4(GRADES)	-	0	-
6-6.1(Nuts)	-	0	-
6-6.2.1(Washers)	-	0	-
6-.6.2.2(Washers)	-	0	-
7(GENERAL REQUIREMENTS)	-	1200	Dimension
8.2()	-	0	-
8.3()	-	0	-
9(SAMPLING, INSPECTION AND ACCEPTANCE CRITERIA)	-	0	-
12(MARKING)	-	0	-
13(PACKAGING)	-	0	-

17 Feb, 2028

-
Included w.e.f. 22.02.2024

IS 5872 (1990)

Cold rolled steel strips (Box Strappings) - Specification

All Grade / Type / Size / Designation as per IS 5872

8180 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(UTM)	-	900	Rs 900/ sample for Mechanical testing Note : sample preparation charges extra.
Cl 7(Bending To Both Side At 90°, Then Straight)	-	1000	Rs. 1000/ sample for Bend and re- bend test Note : sample preparation charges extra.
Cl 9(Workmanship)	-	500	Rs 500/ sample for freedom from defects.
Cl 10(Width & Thickness)	-	1200	Rs 1200/ sample for dimensional tolerances.
5(Chemical Composition)	-	880	C, Mn, P, S = Rs 100/Element = Rs 400 Nb, V, Ti, B = Rs120/Element. = Rs 480
Cl 11(Workmanship)	-	500	-
Cl 12(Coating)	-	500	-

17 Feb, 2028

-
-

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

All Grade / Type / Size / Designation as per IS 2062

16520 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 10.3(UTM)	-	900	Rs 900/ sample for Mechanical Testing Sample Preparation charges extra. -
Cl 11.3(Press)	-	500	Rs 500/ sample for Bend Test. Sample Preparation charges extra.
Cl 12(Sudden Load Applied)	-	4000	RS 1000 / set for impact test at ambient temp. Rs 3000/ set for Impact test at Sub Zero temp. (-20 degree C)
Cl 15(Length, Width & Thickness)	-	1700	Rs 1200 / sample for Dimensions. Rs 500/- for calculation of mass.
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Nb, Ti, B, Cr, Mo, V, Ni, Cu, Al, = Rs 120/Element If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2500	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	580	Nb, Ti, B, Al = 120/ element= 480/- Carbon= 100/- Total= 480+100= 580/-
14.1(Soundness test)	-	1000	-
14.2(Grain Size)	-	400	-
14.2(Inclusion)	-	400	-
Cl 13(Y Groove Cracking Test)	-	2000	-
Cl 7(Workmanship)	-	500	-
Cl 18(Weight)	-	500	-
16(Tolerance)	-	500	-

17 Feb, 2028

-
-

IS 6118 (2017)

Pliers and nippers - Multiple slip joint pliers - Dimensions and test values (Second Revision)

All Grade / Type / Size / Designation etc

3360 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 1(l)	-	2660	Rs 1200 for dim.= 1200/ - C, Si, Mn, P, S = Rs 100/Element. = Rs 500 - Cr, Cu, V, Mo, Ni, W, Sn, Co = Rs 120/Element. = Rs 960
Table 1(t1, max)	-	700	Hardness Test (HV or HRc) = 400/- Handle load Test = 300/-
Table 1(g, min)	-	0	0
Table 1(l3.min)	-	0	-
Table 1(l1)	-	0	-
Table 1(Fa)	-	0	-
Table 1(Sb)	-	0	-

17 Feb, 2028

-
Revised version of IS 6118:2017 included.

IS 15647 (2006)

Hot rolled steel narrow width strip for welded tubes and pipes

All Grade / Type / Size / Designation

7720 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(UTM)	-	1300	Rs 1300/ sample for mechanical Test - C, Si, Mn, P, S = Rs 90/Element - Al = Rs 110/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element
Cl 9(Press)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 12(Length, Width & Thickness)	-	1200	-
Cl 8(UTM)	-	1300	-
Cl 9(Press)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 12(Length, Width & Thickness)	-	1200	-

17 Feb, 2028

-
-

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

All Grade / Type / Size / Designation as per 11513

4420 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	90	- C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1(Manganese %)	-	90	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1(Phosphorus %)	-	90	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1(Sulphur %)	-	90	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1(Silicon %)	-	90	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1( Aluminium %)	-	110	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1( Copper %)	-	110	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1( Nb)	-	110	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1(V)	-	110	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
6.1( Ti)	-	110	C, Si, Mn, P, S = Rs 90/Element Cr, Mo, V, Ni, Cu, Al = Rs 110/Element. - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl 8(Workmanship)	-	500	Rs 500/ sample for freedom from defects.
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-	3000	Rs 3000/ sample for Dimensions & tolerance
6.1(Carbon %)	-	90	-
6.1(Manganese %)	-	90	-
6.1(Phosphorus %)	-	90	-
6.1(Sulphur %)	-	90	-
6.1(Silicon %)	-	110	-
6.1( Aluminium %)	-	110	-
6.1( Copper %)	-	110	-
6.1( Nb)	-	110	-
6.1(V)	-	110	-
6.1( Ti)	-	110	--
Cl 8(Workmanship)	-	500	-
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-	3000	-

17 Feb, 2028

-
-

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

All Grade / Type / Size / Designation as per IS 10748

7560 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Carbon %)	-	100	- C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al = Rs 120/Element
7.1(Manganese %)	-	100	-
7.1(Phosphorus %)	-	100	-
7.1(Sulphur %)	-	100	-
7.1(Silicon %)	-	100	-
7.1( Copper %)	-	120	-
7.1(Ni)	-	120	-
7.1(V)	-	120	-
7.1( Nb)	-	120	-
7.1(Mo)	-	120	-
7.1(Cr)	-	120	-
Cl 8 & Table 3(UTM)	-	900	Rs 900/ sample for mechanical test. Note : sample preparation charges extra.
Cl 9(Press)	-	500	Rs 500/ sample for Bend test. Note : sample preparation charges extra.
Cl 11(Workmanship)	-	500	Rs 500/ sample for freedom from defects.
Cl 12 & 13(Length, Width & Thickness)	-	1200	Rs 1200/ sample for dimension and tolerances
7.1( Aluminium %)	-	120	-
7.1( Ti)	-	120	-
7.1(CE)	-	500	-
7.1( Nitrogen%)	-	2500	-

17 Feb, 2028

-
-

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

All Grade / Type / Size / Designation as per IS 7887

2320 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	100	- C, Si, Mn, P, S = Rs 100/Element - Al = Rs 120/Element.
6.1(Silicon %)	-	100	-
6.1(Manganese %)	-	100	-
6.1(Phosphorus %)	-	100	-
6.1(Sulphur %)	-	100	-
6.1( Aluminium %)	-	120	-
Cl 8(Workmanship)	-	500	Rs 500/ sample for freedom from defects.
Cl 9(Nominal Diameter & Out Of Shape)	-	1200	Rs 1200/ sample for dimensions.

17 Feb, 2028

-
-

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

All Grade / Type / Size / Designation

14880 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Carbon %)	-	100	- C, Si, Mn, P, S, = Rs 100/Element - Nb, Ti, B, Ni, Cr, Cu, V, Mo, Al, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element
7.1(Silicon %)	-	100	-
7.1(Manganese %)	-	100	-
7.1(Phosphorus %)	-	100	-
7.1(Sulphur %)	-	100	-
7.1(Ni)	-	120	-
7.1(Cr)	-	120	-
7.1(Mo)	-	120	-
7.1(V)	-	120	-
7.1( Aluminium %)	-	120	-
7.1( Copper %)	-	120	-
Cl 13(Workmanship)	-	500	Rs 500/ sample for Freedom from defects
Cl 8(UTM)	-	900	Rs 900/ sample for mechanical testing. Note: Sample preparation charges extra.
Cl 9(Press)	-	500	Rs 500/ sample for bend test. Note: Sample preparation charges extra.
Cl 10(Sudden Load Applied)	-	4000	Rs 1000/ set for Impact Test at ambient temp. Rs 3000/ set for impact test at Sub zero Temp.
Cl 15(Length, Width & Thickness)	-	1700	Rs 1200/ sample for Dimensions. Rs 500/- for calculation of mass
Cl 11(Expansion Test)	-	500	-
7.1( Nb)	-	120	-
7.1( Ti)	-	120	-
7.1(CE)	-	620	CE + B= 500+120=620/-
Cl 14(Weldability)	-	500	-
Clause 16(IS 5986)	-	500	-

17 Feb, 2028

-
-

IS 3502 (2009)

Steel chequered plates (Third Revision)

All Grade / Type / Size / Designation as per IS 3502

8720 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(Workmanship)	-	500	-
Cl 8(UTM)	-	900	Rs 900/ sample for mechanical test. Note:Sample preparation charges extra
Cl 9(Press)	-	500	Rs 500/ sample for Bend test. Note:Sample preparation charges extra
Cl 10(Length, Width, Thickness & Chequered Height)	-	1700	Rs 1200/ sample for Dimensions. Rs 500/ for calculation of mass.
Cl.4.1 (IS-2062, E250A)(CARBON)	-	1180	C = Rs 100 Nb, Ti, B, Ni, Cr, Cu, V, Mo, Al = Rs 120/Element =1080/-
Cl.4.1 (IS-2062, E250A)(SILICON)	-	100	-
Cl.4.1 (IS-2062, E250A)(MANGANESE)	-	100	-
Cl.4.1 (IS-2062, E250A)(PHOSPHURS)	-	100	-
Cl.4.1 (IS-2062, E250A)(SULPHUR)	-	100	-
Cl.4.1 (IS-2062, E250A)(NITROGEN)	-	2500	-
Cl.4.1 (IS-2062, E250A)(CARBON EQUIVALENT)	-	500	-
Cl. 11(Weight)	-	500	-

17 Feb, 2028

-
-

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

All Grade / Type / Size / Designation as per IS 6240

13630 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	100	C, Si, Mn, P, S = Rs 100/ Element Ti, Nb V, Al, = Rs 120/Element.
6.1(Silicon %)	-	100	-
6.1(Manganese %)	-	100	-
6.1(Phosphorus %)	-	100	-
6.1(Sulphur %)	-	100	-
6.1( Aluminium %)	-	480	Nb,Ti,V, Al=480/-
6.1(Nitrogen%)	-	2500	-
Cl 7(UTM)	-	900	Rs 900/sample for Mechanical test. Sample preparation charges extra.
Cl 8(Press)	-	500	Rs 500/ sample for bend test
Cl 9(Strainage Embrittlement)	-	4500	Rs 4500/ sample for strainage embrittlement
Cl 10(Erichsen Cupping)	-	500	Rs 500/ sample for Erichsen Cupping
Cl 13(Length, Width & Thickness)	-	1200	Rs 1200 Dimensions & Tolerance.
Cl. 12(Freedom from defects)	-	500	-

17 Feb, 2028

-
-

IS 5517 (1993)

Steels for hardening and tempering - Speicification (Second Revision)

All grade, Type, size and designation as per IS 5517

44010 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Aluminium IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Boron- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	- C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Tin- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	- C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
8,Table 6(Hardness Test - IS 1500(Pt -1))	-	400	Rs 400/ sample for hardness testing.
9, Table 5(Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-	1900	Rs 900 for mechanical testing, Rs 1000 for Izod Impact testing . Note : Sample preparation charges extra.
10(Grain Size - IS 4748)	-	400	Rs 400/ sample for Grain size.
11.1(Inclusion Rating- IS 4163)	-	400	Rs 400/ sample for inclusion rating.
12;Table 7(Hardenability Test-IS 3848)	-	5000	Rs 5000/ sample for harden ability test.
13.1&13.2&13.3(Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-	1200	Rs 1200/ sample for dimensional tolerances.
11.2(Blue Fracture Test - IS 10138 (Pt1))	-	4500	-
16.1 d);Table 5(Additional Test;Blank Hardening Test)	-	6000	-
16.1 g)(Hot up set for forgability)	-	6000	-
16.1 b)(Additional Test; Ultrasonic Test -IS 3664)	-	1000	-
11.2(Magnetic Particle Test -- IS 10138(Pt3))	-	1000	-
11.2(Step Down Test- IS 10138(Pt2))	-	1000	-
5(Freedom from defects , IS 5517)	-	500	-
16.1 f)(Microstructure for machinability,including banding)	-	500	-
16.1 a)(Additional Test; Macro etch Test)	-	1000	-

17 Feb, 2028

-
-

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

All Grade, Type, Size and Designation as per IS 1079

9320 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	100	Note: - C, Si, Mn, P, S = Rs 100/Element Cr, Mo, V,Ni, Cu, Al =120/Element If "N” is required, then testing charges will be extra @ 1000/- per Sample for this element.
6.1(Manganese %)	-	100	-
6.1(Phosphorus %)	-	100	-
6.1(Sulphur %)	-	100	-
Cl 8(UTM)	-	900	Rs 900 for Mechanical test (For YS, TS, Elongation) Note: Sample Preparation Charges Extra.
Cl 9(Press)	-	0	RS 500/ sample for bend test Note: Sample Preparation Charges Extra.
Cl 10(Die Press)	-	500	Rs 500/ sample for cupping test Note: Sample Preparation Charges Extra.
Cl 12(Workmanship)	-	500	Rs 500/ sample
Cl 13(Length, Width & Thickness)	-	1200	Rs 1200 for dimensional tolerances.
6.1(Silicon %)	-	100	-
6.1( Nb)	-	120	-
6.1( Ti)	-	120	-
6.1(V)	-	120	-
6.1(Microalloying)	-	120	Boron as micro alloying Element
6.1( Copper %)	-	120	-
6.1( Aluminium %)	-	120	-
9(Bend test)	-	500	-
14(Calculation of weight)	-	500	-

17 Feb, 2028

-
-

IS 3650 (1981)

Specification for combination side cutting pliers (Second Revision)

All Grade, Type, Size and Designation as per IS 3650

5560 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 Table 1(Dimensions- L)	-	1200	Rs. 1200/- dimensional inspection charges
3 Table 1(Dimensions- a)	-	0	---
3 Table 1(Dimensions- b)	-	0	--
3 Table 1(Dimensions- c1)	-	0	--
3 Table 1(Dimensions- e)	-	0	---
3 Table 1(Dimensions- h)	-	0	--
3 Table 1(Dimensions- h1)	-	0	--
3 Table 1(Dimensions- t)	-	0	-
4(Hardness- Near cutting edges)	-	400	-
4(Hardness- Body gripping surfce)	-	0	---
8.2(Tube Gripping Test)	-	200	--
8.3(Shock Test)	-	200	--
8.4(Torsion Test)	-	300	---
8.5(Handle Load Test)	-	300	--
8.6(Bend Test)	-	200	--
8.7(Insulation Test)	-	400	--
8.1(Cutting Test)	-	200	--
5(Material testing (Chemical composition))	-	1960	- C, Si, Mn, P, S = Rs 100/Element. = Rs 500 (for jaws) - C, Si, Mn, P, S = Rs 100/Element. = Rs 500 (for Rivet) - Cr, Cu, V, Mo, Ni, W, Sn, Co = Rs 120/Element. = Rs 960

17 Feb, 2028

-
-

IS 2029 (1998)

Ring wrenches (Spanners) - Specification (Fourth Revision)

All grade,Type, Size and Designation as per IS 2029

4190 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3, Table-1(Dimensions- s1)	-	1200	Complete Inspection charges Rs 1200/-. C, Si, Mn, P, S = Rs 90/Element Cr, Mo V, Ni, Cu, Al, = Rs 110/Element If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
3, Table-1(Dimensions- s2)	-	0	-
3, Table-1(Dimensions- a)	-	0	-
3, Table-1(Dimensions- b1)	-	0	-
3, Table-1(Dimensions- b2)	-	0	-
3, Table-1(Dimensions- L)	-	0	-
5(Hardness)	-	300	Rs 300/ sample for Hardness Testing.
6(Workmanship and Finish)	-	500	Rs 500/ sample for freedom from defects
6(Torque Testing)	-	300	Rs 300/ sample for Torque Testing.
3, Table-1(Dimensions- s1)	-	-	-
3, Table-1(Dimensions- s2)	-	-	-
3, Table-1(Dimensions- a)	-	-	-
3, Table-1(Dimensions- b1)	-	-	-
3, Table-1(Dimensions- b2)	-	-	-
3, Table-1(Dimensions- L)	-	-	-
5(Hardness)	-	-	-
6(Workmanship and Finish)	-	-	-
6(Torque Testing)	-	-	-

17 Feb, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Institute for Auto Parts and Hand Tools Technology

A-9, Phase-V, Focal Point, Ludhiana, Ludhiana, Ludhiana, Punjab, 141010

8427262400 iatldh@iapht.org

Scope List