BIS - LIMS (Laboratory Information Management System)

Institute for Auto Parts and Hand Tools Technology, Ludhiana

A-9, Phase-V, Focal Point, Ludhiana, Ludhiana, Ludhiana, Punjab, 141010

8427262400 iatldh@iapht.org

Scope List

Reset

74 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

All Grade / Type / Size / Designation

14880 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Carbon %)	-	100	- C, Si, Mn, P, S, = Rs 100/Element - Nb, Ti, B, Ni, Cr, Cu, V, Mo, Al, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element
7.1(Silicon %)	-	100	-
7.1(Manganese %)	-	100	-
7.1(Phosphorus %)	-	100	-
7.1(Sulphur %)	-	100	-
7.1(Ni)	-	120	-
7.1(Cr)	-	120	-
7.1(Mo)	-	120	-
7.1(V)	-	120	-
7.1( Aluminium %)	-	120	-
7.1( Copper %)	-	120	-
Cl 13(Workmanship)	-	500	Rs 500/ sample for Freedom from defects
Cl 8(UTM)	-	900	Rs 900/ sample for mechanical testing. Note: Sample preparation charges extra.
Cl 9(Press)	-	500	Rs 500/ sample for bend test. Note: Sample preparation charges extra.
Cl 10(Sudden Load Applied)	-	4000	Rs 1000/ set for Impact Test at ambient temp. Rs 3000/ set for impact test at Sub zero Temp.
Cl 15(Length, Width & Thickness)	-	1700	Rs 1200/ sample for Dimensions. Rs 500/- for calculation of mass
Cl 11(Expansion Test)	-	500	-
7.1( Nb)	-	120	-
7.1( Ti)	-	120	-
7.1(CE)	-	620	CE + B= 500+120=620/-
Cl 14(Weldability)	-	500	-
Clause 16(IS 5986)	-	500	-

17 Feb, 2028

-
-

IS 3502 (2009)

Steel chequered plates (Third Revision)

All Grade / Type / Size / Designation as per IS 3502

8720 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(Workmanship)	-	500	-
Cl 8(Tensile Test)	-	900	Rs 900/ sample for mechanical test. Note:Sample preparation charges extra
Cl 9(Press)	-	500	Rs 500/ sample for Bend test. Note:Sample preparation charges extra
Cl 10(Length, Width, Thickness & Chequered Height)	-	1700	Rs 1200/ sample for Dimensions. Rs 500/ for calculation of mass.
Cl.4.1 (IS-2062, E250A)(CARBON)	-	1180	C = Rs 100 Nb, Ti, B, Ni, Cr, Cu, V, Mo, Al = Rs 120/Element =1080/-
Cl.4.1 (IS-2062, E250A)(SILICON)	-	100	-
Cl.4.1 (IS-2062, E250A)(MANGANESE)	-	100	-
Cl.4.1 (IS-2062, E250A)(PHOSPHURS)	-	100	-
Cl.4.1 (IS-2062, E250A)(SULPHUR)	-	100	-
Cl.4.1 (IS-2062, E250A)(NITROGEN)	-	2500	-
Cl.4.1 (IS-2062, E250A)(CARBON EQUIVALENT)	-	500	-
Cl. 11(Weight)	-	500	-

17 Feb, 2028

-
-

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

All Grade / Type / Size / Designation as per IS 6240

13630 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	100	C, Si, Mn, P, S = Rs 100/ Element Ti, Nb V, Al, = Rs 120/Element.
6.1(Silicon %)	-	100	-
6.1(Manganese %)	-	100	-
6.1(Phosphorus %)	-	100	-
6.1(Sulphur %)	-	100	-
6.1( Aluminium %)	-	480	Nb,Ti,V, Al=480/-
6.1(Nitrogen%)	-	2500	-
Cl 7(UTM)	-	900	Rs 900/sample for Mechanical test. Sample preparation charges extra.
Cl 8(Press)	-	500	Rs 500/ sample for bend test
Cl 9(Strainage Embrittlement)	-	4500	Rs 4500/ sample for strainage embrittlement
Cl 10(Erichsen Cupping)	-	500	Rs 500/ sample for Erichsen Cupping
Cl 13(Length, Width & Thickness)	-	1200	Rs 1200 Dimensions & Tolerance.
Cl. 12(Freedom from defects)	-	500	-

17 Feb, 2028

-
-

IS 5517 (1993)

Steels for hardening and tempering - Speicification (Second Revision)

All grade, Type, size and designation as per IS 5517

44010 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Aluminium IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Boron- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	- C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Tin- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	120	- C, Si, Mn, P, S = Rs 100/Element - Ni, Cr, Cu, V, Mo, Al, B, = Rs 120/Element - If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
8,Table 6(Hardness Test - IS 1500(Pt -1))	-	400	Rs 400/ sample for hardness testing.
9, Table 5(Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-	1900	Rs 900 for mechanical testing, Rs 1000 for Izod Impact testing . Note : Sample preparation charges extra.
10(Grain Size - IS 4748)	-	400	Rs 400/ sample for Grain size.
11.1(Inclusion Rating- IS 4163)	-	400	Rs 400/ sample for inclusion rating.
12;Table 7(Hardenability Test-IS 3848)	-	5000	Rs 5000/ sample for harden ability test.
13.1&13.2&13.3(Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-	1200	Rs 1200/ sample for dimensional tolerances.
11.2(Blue Fracture Test - IS 10138 (Pt1))	-	4500	-
16.1 d);Table 5(Additional Test;Blank Hardening Test)	-	6000	-
16.1 g)(Hot up set for forgability)	-	6000	-
16.1 b)(Additional Test; Ultrasonic Test -IS 3664)	-	1000	-
11.2(Magnetic Particle Test -- IS 10138(Pt3))	-	1000	-
11.2(Step Down Test- IS 10138(Pt2))	-	1000	-
5(Freedom from defects , IS 5517)	-	500	-
16.1 f)(Microstructure for machinability,including banding)	-	500	-
16.1 a)(Additional Test; Macro etch Test)	-	1000	-

17 Feb, 2028

-
-

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

All Grade, Type, Size and Designation as per IS 1079

9320 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	100	Note: - C, Si, Mn, P, S = Rs 100/Element Cr, Mo, V,Ni, Cu, Al =120/Element If "N” is required, then testing charges will be extra @ 1000/- per Sample for this element.
6.1(Manganese %)	-	100	-
6.1(Phosphorus %)	-	100	-
6.1(Sulphur %)	-	100	-
Cl 8(UTM)	-	900	Rs 900 for Mechanical test (For YS, TS, Elongation) Note: Sample Preparation Charges Extra.
Cl 9(Press)	-	0	RS 500/ sample for bend test Note: Sample Preparation Charges Extra.
Cl 10(Die Press)	-	500	Rs 500/ sample for cupping test Note: Sample Preparation Charges Extra.
Cl 12(Workmanship)	-	500	Rs 500/ sample
Cl 13(Length, Width & Thickness)	-	1200	Rs 1200 for dimensional tolerances.
6.1(Silicon %)	-	100	-
6.1( Nb)	-	120	-
6.1( Ti)	-	120	-
6.1(V)	-	120	-
6.1(Microalloying)	-	120	Boron as micro alloying Element
6.1( Copper %)	-	120	-
6.1( Aluminium %)	-	120	-
9(Bend test)	-	500	-
14(Calculation of weight)	-	500	-

17 Feb, 2028

-
-

IS 3650 (1981)

Specification for combination side cutting pliers (Second Revision)

All Grade, Type, Size and Designation as per IS 3650

5560 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 Table 1(Dimensions- L)	-	1200	Rs. 1200/- dimensional inspection charges
3 Table 1(Dimensions- a)	-	0	---
3 Table 1(Dimensions- b)	-	0	--
3 Table 1(Dimensions- c1)	-	0	--
3 Table 1(Dimensions- e)	-	0	---
3 Table 1(Dimensions- h)	-	0	--
3 Table 1(Dimensions- h1)	-	0	--
3 Table 1(Dimensions- t)	-	0	-
4(Hardness- Near cutting edges)	-	400	-
4(Hardness- Body gripping surfce)	-	0	---
8.2(Tube Gripping Test)	-	200	--
8.3(Shock Test)	-	200	--
8.4(Torsion Test)	-	300	---
8.5(Handle Load Test)	-	300	--
8.6(Bend Test)	-	200	--
8.7(Insulation Test)	-	400	--
8.1(Cutting Test)	-	200	--
5(Material testing (Chemical composition))	-	1960	- C, Si, Mn, P, S = Rs 100/Element. = Rs 500 (for jaws) - C, Si, Mn, P, S = Rs 100/Element. = Rs 500 (for Rivet) - Cr, Cu, V, Mo, Ni, W, Sn, Co = Rs 120/Element. = Rs 960

17 Feb, 2028

-
-

IS 2029 (1998)

Ring wrenches (Spanners) - Specification (Fourth Revision)

All grade,Type, Size and Designation as per IS 2029

4190 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3, Table-1(Dimensions- s1)	-	1200	Complete Inspection charges Rs 1200/-. C, Si, Mn, P, S = Rs 90/Element Cr, Mo V, Ni, Cu, Al, = Rs 110/Element If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element.
3, Table-1(Dimensions- s2)	-	0	-
3, Table-1(Dimensions- a)	-	0	-
3, Table-1(Dimensions- b1)	-	0	-
3, Table-1(Dimensions- b2)	-	0	-
3, Table-1(Dimensions- L)	-	0	-
5(Hardness)	-	300	Rs 300/ sample for Hardness Testing.
6(Workmanship and Finish)	-	500	Rs 500/ sample for freedom from defects
6(Torque Testing)	-	300	Rs 300/ sample for Torque Testing.
3, Table-1(Dimensions- s1)	-	-	-
3, Table-1(Dimensions- s2)	-	-	-
3, Table-1(Dimensions- a)	-	-	-
3, Table-1(Dimensions- b1)	-	-	-
3, Table-1(Dimensions- b2)	-	-	-
3, Table-1(Dimensions- L)	-	-	-
5(Hardness)	-	-	-
6(Workmanship and Finish)	-	-	-
6(Torque Testing)	-	-	-

17 Feb, 2028

-
-

IS 2028 (2004)

Open jaw wrenches (Spanners) - Specification (Fijih Revision)

All Grade, Type, Size and designation as per IS 2028

4060 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Dimensions- a)	-	1200	Rs 1200/ sample for complete dimensional inspection.
3.2, 3.3, 3.4(Dimensions- a)	-	0	-
3.2, 3.3, 3.4(Dimensions- l)	-	0	-
5(Hardness- upto 32 mm)	-	400	Rs 400/ sample for Hardness test
6(Workmanship And Finish)	-	500	Rs 500/ sample for freedom from defects.
8(Tourque test)	-	500	Rs 500 for torque Testing.
4(Chemical Composition)	-	1460	C, Si, Mn, P, S = Rs 100/Element Cr, Mo, V, Ni, Cu, Al , Co, Sn= Rs 120/Element Total for chemical Testing =1460

17 Feb, 2028

-
-

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

All Grade,Type,Size and designation as per IS 1875:1992

16470 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 12(Supplementary Requirements)	-	5000	Note; - Rs 4500/- for Blue Fracture Test and RS 500 for Bend Test.
Cl 7(Workmanship)	-	500	Rs 500/ sample for freedom from defects.
Cl 8(Diameter, Ovality & Weight)	-	1200	RS 1200/sample for inspection.
Cl 9(UTM & HBW)	-	1300	Rs 900 for Mechanical Test and Rs 400 for Hardness test . Note : Sample preparation charges extra.
Cl 12(Supplementary Requirements)	-	3400	Rs 400/ sample for Grain size, Rs 1000/ sample for Macro structure, Rs 1000/ Sample for UT, Rs 1000/sample MPI, Note: Sample preparation charges extra.
6.1, 6.2(cr + n + mo)	-	200	Rs 100 for (Cr+Ni+Mo) Rs 100 for (Cu+10 x % Sn)
6.1, 6.2(tin)	-	120	-
6.1, 6.2(boron)	-	120	-
6.1, 6.2(vanadium)	-	120	-
6.1, 6.2(molybdenum)	-	120	-
6.1, 6.2(copper)	-	120	-
6.1, 6.2(aluminium)	-	120	-
6.1, 6.2(phosphorus)	-	100	-
6.1, 6.2(sulphur)	-	100	-
6.1, 6.2(manganese)	-	100	-
6.1, 6.2(silicon )	-	100	-
6.1, 6.2(carbon)	-	100	-
6.1, 6.2(cromium)	-	120	-
6, table 1(Chemical Composition)	-	120	for Ni = Rs 120/Element If "N” is required, then testing charges will be extra @ 2500/- per Sample for this element

17 Feb, 2028

-
-

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

All Grade ,Type ,Size, Designation as per IS 432 (II)

8220 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.1.1(Sulphur)	-	300	- Only for P and S element minimum billing = Rs 600. - If “N " is required, then testing charges will be extra @ 2500/- per Sample for this element.
Clause 3.1.1(Phosphorus)	-	300	- Only for P and S element minimum billing = Rs 600. - If “N " is required, then testing charges will be extra @ 2500/- per Sample for this element.
Cl 4.1(Workmanship)	-	500	Rs 500/ sample for freedom from defects .
Cl 5 & 6(Diameter)	-	1200	Rs 1200/ sample for dimensional tolerance.
Cl 7(UTM)	-	900	RS 900/ sample for mechanical testing Sample preparation charges extra.
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	1000	RS 1000/ sample for Bend and Re Bend Test. Sample preparation charges extra.

17 Feb, 2028

-
-

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

All Grade, Type, Size and designation as per IS 432

8200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	400	Rs 400/ sample for freedom from defects. sample Preparation Charges Extra. Rs. 1110 for Chemical Testing C, Si, Mn, P, S =Rs 90/Element Ni, Cr, Cu, V, Mo, Al = Rs 110/Element.
Cl 6.2(Diameter & Ovality)	-	600	RS 600/ sample for Nominal Size & Mass.
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	800	Rs 800/ sample for Mechanical Testing sample Preparation Charges Extra.
Cl 9.3(Press)	-	500	Rs 500/ sample for Bend Test sample Preparation Charges Extra.
Cl 5.1(Workmanship)	-	400	Rs 400/ sample for freedom from defects. sample Preparation Charges Extra.
Clause -4, 4.3(TITANIUM)	-	110	Rs. 1110 for Chemical Testing C, Si, Mn, P, S =Rs 90/Element Ni, Cr, Cu, V, Mo, Al = Rs 110/Element.
Clause -4, 4.2(VANADIUM)	-	110	-
Clause -4, 4.1(NIOBIUM)	-	110	-
Clause -4, 4.1(Molybdenum)	-	110	-
Clause -4, 4.1(Chromium)	-	110	-
Clause -4, 4.1(Nickel)	-	110	-
Clause -4, 4.1( ALUMINIUM)	-	110	-
Clause -4, 4.1(SILICON)	-	90	-
Clause -4, 4.1(NITROGEN)	-	110	-
Clause -4, 4.1(MANGANESE)	-	90	-
Clause -4, 4.1(PHOSPHURS)	-	90	-
Clause -4, 4.1(SULPHUR)	-	90	-
Clause -4, 4.1( CARBON)	-	90	-

17 Feb, 2028

-
-

IS 273 (1990)

Picks and beaters - specification (Fourth Revision)

All Grade / Type / Size / Designation as per IS 273

3800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	1200	-
4(Material testing)	-	1100	-
7(Workmanship and finish)	-	500	-
9.1(Drop Test)	-	500	-
9.2(Striking Test)	-	500	-
3(Dimensions)	-	0	-
4(Material testing)	-	0	-
7(Workmanship and finish)	-	0	-
9.1(Drop Test)	-	0	-
9.2(Striking Test)	-	0	-
3(Dimensions)	-	0	-
4(Material testing)	-	0	-
7(Workmanship and finish)	-	0	-
9.1(Drop Test)	-	0	-
9.2(Striking Test)	-	0	-

17 Feb, 2028

-
Included w.e.f. 05.12.2023

IS 4296 : Part 2 (2015)

Tools for pressing: Part 2 punches with cylindrical head and straight or reduced shank (First Revision)

All Grade/Type/Size/Designation as per IS 4296 -2

4370 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions & Tolerance)	-	1500	-
4(Surface Roughness)	-	1250	-
5(Material Testing)	-	1220	- C, Si, Mn, P, S - Rs. 100/- per element - Ni, Cr, V, Mo, Co, W- Rs. 120/- per element
5.2(Hardness (HRC))	-	400	-
4(Dimensions & Tolerance)	-	0	-
4(Surface Roughness)	-	0	-
5(Material Testing)	-	0	-
5.2(Hardness (HRC))	-	0	-

17 Feb, 2028

-
Included w.e.f. 05.12.2023

IS 1570 : Part 2 (1979)

Schedules for wrought steels: Part 2 carbon steels (Unalloyed Steels)

Grade/Type/Size/Designation as per IS 1570 (Part-II)

11140 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-2Table-3,Table-4,Table-5,Table-6,Table-7,Table-8(Izod Impact value,Min)	-	3540	Chemical testing charges - Rs. 1540/- Limiting Ruling section - 2000/-
Table-2Table-3,Table-4,Table-5,Table-6,Table-7,Table-8(Elongation)	-	4000	Impact test= Rs. 4000/-
Table-2Table-3,Table-4,Table-5,Table-6,Table-7,Table-8(Yield strength, Min)	-	3300	TS
Table-2Table-3,Table-4,Table-5,Table-6,Table-7,Table-8(Tensile strength)	-	300	-
Table-2Table-3,Table-4,Table-5,Table-6,Table-7,Table-8(Izod Impact value,Min)	-	0	-
Table-2Table-3,Table-4,Table-5,Table-6,Table-7,Table-8(Elongation)	-	0	-
Table-2Table-3,Table-4,Table-5,Table-6,Table-7,Table-8(Yield strength, Min)	-	0	-
Table-2Table-3,Table-4,Table-5,Table-6,Table-7,Table-8(Tensile strength)	-	0	-

17 Feb, 2028

-
Included w.e.f. 05.12.2023

Bureau of Indian Standards

The National Standards Body of India

Institute for Auto Parts and Hand Tools Technology, Ludhiana

A-9, Phase-V, Focal Point, Ludhiana, Ludhiana, Ludhiana, Punjab, 141010

8427262400 iatldh@iapht.org

Scope List