BIS - LIMS (Laboratory Information Management System)

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List

Reset

334 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2191 : Part 1 (2022)

WOODEN FLUSH DOOR SHUTTERS CELLULAR TUBULAR AND HOLLOW CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Fifth Revision

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Sizes)	-	400	-
Cl-6.1.1(Species of timber)	-	1500	-
Cl-6.3(Cross-Bands)	-	1500	-
Cl-6.4.1(Commercial face veneers)	-	1500	-
Cl-6.4.2(Decorative face veneers)	-	1500	-
Cl-6.7(Particle Board)	-	1500	-
Cl-6.8(Laminated veneer lumber (LVL), veneer laminated lumber (VLL), Medium Density Fibre (MDF))	-	1500	-
Cl-11.1(Dimensions and Squareness Test)	-	500	-
Cl-11.2(General Flatness Test)	-	1000	-
Cl-11.3(Local Planeness Test)	-	1000	-
Cl-11.4(Impact Indentation Test)	-	1000	-
Cl-11.5(Flexure Test)	-	1500	-
Cl-11.6(Edge Loading Test)	-	1000	-
Cl-11.7(Shock Resistance Test)	-	1000	-
Cl-11.8(Buckling Resistance Test)	-	1500	-
Cl-11.9(Slamming Test)	-	1500	-
Cl-11.10(Misuse Test)	-	1500	-
Cl-11.11(Varying Humidity Test)	-	6000	-
Cl-11.12(End Immersion Test)	-	1500	-
Cl-11.13(Knife Test)	-	1000	-
Cl-11.15(Screw Withdrawal Resistance Test)	-	2000	-
Cl-12.2(Sample Size)	-	100	-
Cl-14(Marking)	-	100	-
Cl-6.1.2(Moisture content of timber)	-	500	-
Cl-9(Workmanship and Finish)	-	500	-
Cl-6.1.3(Defects)	-	200	-
Cl-6.2(Plywood)	-	500	-
Cl-6.5(Cross-bands and face veneers)	-	500	-
Cl-6.6(Adhesives)	-	500	-
Cl-7(Construction)	-	500	-
Cl-8(Fittings)	-	500	-
Cl-11.14(Glue Adhesion Test)	-	1500	-

-
Included w.e.f. 13.01.2025

IS 17954 (2023)

TELESCOPIC BALL BEARING DRAWER SLIDE SPECIFICATION

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2, Table- 2 (i)(Internal channel)	-	500	-
Cl-4.2, Table- 2 (ii)(Outer channel)	-	500	-
Cl-4.2, Table- 2 (iii)(Track up to 550 mm)	-	500	-
Cl-4.2, Table- 2 (iv)(Track from 600 mm onwards)	-	500	-
Cl-4.2, Table- 2 (v)(Ball cage)	-	500	-
Cl-4.2, Table- 2 (vi)(Ball spacer)	-	500	-
Cl-5(Components and Manufacture)	-	0	-
Cl-5(Components and Manufacture)	-	0	-
Cl-6.1(Preparatory Measures)	-	0	-
Cl-6.2 (a)(Limiting Deviations- Force)	-	0	-
Cl-6.2 (b)(Limiting Deviations- Speed)	-	0	-
Cl-6.2 (c)(Limiting Deviations- Weights)	-	0	-
Cl-6.2 (d)(Limiting Deviations- Dimension)	-	0	-
Cl-6.3(Application of Forces)	-	0	-
Cl-6.4(Testing Equipment)	-	0	-
Cl-6.5(Sequence of testing)	-	0	-
Cl-7(Vertical Load Test)	-	3999.98	-
Cl-8(Horizontal Load Test)	-	4000	-
Cl-9(Durability Test)	-	5100	-
Cl-10(Deflection Test)	-	3500	-
Cl-11(Slam Test)	-	3500	-
Cl-12(Finish)	-	2500	-
Cl-5.11(Ball)	-	1000	-
Cl-5.10(Rivets)	-	1000	-
4.1(size of the telescopic ball bearing slide)	-	500	-
6.6 (amendment 1)(difference of the maximum forces for opening and closing)	-	500	-

-
Included w.e.f. 13.01.2025

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	1500	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	2000	-
11(Transverse Tension Test,%)	-	2000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	1500	-
13 (Table No.- 7)(Flaring Test)	-	1500	-
14(Flattaning Test-IS 2328)	-	1500	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	2500	-
17(Leak Tighteness Test)	-	3000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	3500	-
19(Eddy current test & Air under water)	-	2500	-
21(Workmanship, Finish and Appearance)	-	500	-
22(Repair by Welding or Grinding)	-	0	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	1000	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	500	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	500	-
Clause 10.1 - Table 4(Tensile Strength)	-	2000	-
Clause 10.1 - Table 4(Percent Elongation)	-	2000	-
Clause 11(Transverse Tension Test)	-	2000	-
Clause 12(Hardness Test)	-	1500	-
Clause 13(Flaring Test)	-	1500	-
Clause 14(Flattening Test)	-	1500	-
Clause 15(Grain Size)	-	2500	-
Clause 17(Leak Tightness Test)	-	3000	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	3500	-
Clause 21(Workmanship, Finish & Appearance)	-	500	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	1000	-
10.2(Hardness test IS 1500 (part-1):2019)	-	1500	-
12.2(Flaring test IS 17878:2022)	-	1500	-
16(Sampling)	-	0	-
24(Marking)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	500	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	500	-

-
Included w.e.f. 13.01.2025

IS 8442 (2024)

Stand Post Type Water and Water-cum-Foam Monitor for Fire Fighting - Specification (Second Revision)

31600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1(Dimensions of inlet flanges)	-	1200	-
Cl-3.2(Monitors)	-	1200	-
Cl-3.3(shape of the monitor)	-	400	-
Cl-3.4(General)	-	400	-
Cl-4, Table-2 (i)(Base flange)	-	400	-
Cl-4, Table-2 (ii)(Water barrel/pipes)	-	400	-
Cl-4, Table-2 (iii)(Reducer/elbow)	-	400	-
Cl-4, Table-2 (iv)(Swivel joint)	-	400	-
Cl-4, Table-2 (v)(Lock handle)	-	400	-
Cl-4, Table-2 (vi)(Manoeuvring handle)	-	400	-
Cl-4, Table-2 (vii)(Worm shaft)	-	400	-
Cl-4, Table-2 (viii)(Hand wheel)	-	400	-
Cl-4, Table-2 (ix)(Solid jet nozzle/ Jet/spray water or foam nozzle)	-	400	-
Cl-4, Table-2 (x)(Stand Post Type Water and Water-cum-Foam Monitor for Fire Fighting — Specification)	-	400	-
Cl-4, Table-2 (xi)(Nozzle washer/ O-rings)	-	400	-
Cl-4, Table-2 (xii)(Drain valve)	-	400	-
Cl-4, Table-2 (xiii)(Pressure gauge)	-	400	-
Cl-6(Workmanship and Finish)	-	400	-
Cl-7(Anti Corrosive Treatment)	-	1000	-
Cl-8(PAINTING)	-	400	-
Cl-9.1(Water Monitor)	-	4500	-
Cl-9.2.1(water-cum-foam monitor with water foam nozzle)	-	14000	-
Cl-9.2.2(water-cum-foam monitor with foam barrel)	-	14000	-
Cl-10(LEAKAGE TEST)	-	3500	-
Cl-12(Marking)	-	100	-
Cl-5(Construction)	-	4500	-

-
Included w.e.f. 13.01.2025

IS 2266 (2024)

STEEL WIRE ROPES FOR GENERAL ENGINEERING PURPOSE - SPECIFICATION (Sixth Revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Minimum breaking force)	-	4000	-
Cl-6(Wire rope)	-	6500	-
Cl-7(Construction)	-	1500	-
Cl-8.1(Fibre Core)	-	2500	-
Cl-8.2(Steel Core)	-	2500	-
Cl-9(Joints)	-	1500	-
Cl-10(Galvanizing)	-	4500	-
Cl-12(Marking)	-	500	-
Cl-4(Rope size and Tolerance)	-	3500	-
Cl-5(Minimum breaking force)	-	0	-
Cl-6(Wire rope)	-	0	-
Cl-7(Construction)	-	0	-
Cl-8.1(Fibre Core)	-	0	-
Cl-8.2(Steel Core)	-	0	-
Cl-9(Joints)	-	0	-
Cl-10(Galvanizing)	-	0	-
Cl-12(Marking)	-	0	-
Cl-4(Rope size and Tolerance)	-	0	-
Cl-5(Minimum breaking force)	-	-	-
Cl-6(Wire rope)	-	-	-
Cl-7(Construction)	-	-	-
Cl-8.1(Fibre Core)	-	-	-
Cl-8.2(Steel Core)	-	-	-
Cl-9(Joints)	-	-	-
Cl-10(Galvanizing)	-	-	-
Cl-12(Marking)	-	-	-
Cl-4(Rope size and Tolerance)	-	-	-
Cl-6 of IS 1835,(Carban)	-	-	-
Cl-6 of IS 1835(Manganese)	-	-	-
Cl-6 of IS 1835(Silicon)	-	-	-
Cl-6 of IS 1835(Sulphur, Max)	-	-	-
Cl-6 of IS 1835(Phosphorus, Max)	-	-	-
Cl-6 of IS 1835(Copper, Max)	-	-	-
Cl-6 of IS 1835(Nickel, Max)	-	-	-
Cl-6 of IS 1835(Chromium, Max)	-	-	-

-
Included w.e.f 09.02.2026

IS 14933 (2001)

High Pressure Fire Fighting Hose -Specification

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Type)	-	500	-
Cl 3.2 & 3.3(Nom ID)	-	500	-
Cl 3.4(Internal Dia)	-	500	-
Cl 4(Length)	-	500	-
Cl 5(Mass)	-	500	-
Cl 6(Coil Dia)	-	500	-
Cl 7(Reinforcement)	-	500	-
Cl 8(Lining)	-	500	-
Cl 9(Cover)	-	500	-
Cl 10(Hydaulic Proof Pressure Test)	-	2500	-
Cl 11(Hydraulic Burst Pressure Test)	-	4000	-
Cl 12(Kink test)	-	2500	-
Cl 13 & Annex A(Adhesion Test)	-	2000	-
Cl 14 & Annex B(Abrasion Resistance Test)	-	3000	-
Cl 15(Accelerated Ageing Test)	-	5000	-
Cl 16(Change in Length)	-	2000	-
Cl 17.1 & Annex C(Ozone Resistance Test)	-	20000	-
Cl 17.2(Oil Resistance Test)	-	3500	-
Cl 17.3(Heat Resistance Test)	-	1500	-
Cl 17.3(Heat Resistance Test)	-	1500	-
Cl 17.2(Oil Resistance Test)	-	3500	-
Cl 17.1 & Annex C(Ozone Resistance Test)	-	20000	Lining - Rs. 12,500/- & Cover - Rs. 12500/-
Cl 16(Change in Length)	-	2000	-
Cl 15(Accelerated Ageing Test)	-	5000	-
Cl 14 & Annex B(Abrasion Resistance Test)	-	3000	-
Cl 13 & Annex A(Adhesion Test)	-	2000	-
Cl 12(Kink test)	-	2500	-
Cl 11(Hydraulic Burst Pressure Test)	-	4000	-
Cl 10(Hydaulic Proof Pressure Test)	-	2500	-
Cl 9(Cover)	-	500	-
Cl 8(Lining)	-	500	-
Cl 7(Reinforcement)	-	500	-
Cl 6(Coil Dia)	-	500	-
Cl 5(Mass)	-	500	-
Cl 4(Length)	-	500	-
Cl 3.4(Internal Dia)	-	500	-
Cl 3.2 & 3.3(Nom ID)	-	500	-
Cl 3.1(Type)	-	500	-
Cl 17.3(Heat Resistance Test)	-	0	-
Cl 17.2(Oil Resistance Test)	-	0	-
Cl 17.1 & Annex C(Ozone Resistance Test)	-	0	-
Cl 16(Change in Length)	-	0	-
Cl 15(Accelerated Ageing Test)	-	0	-
Cl 14 & Annex B(Abrasion Resistance Test)	-	0	-
Cl 13 & Annex A(Adhesion Test)	-	0	-
Cl 12(Kink test)	-	0	-
Cl 11(Hydraulic Burst Pressure Test)	-	0	-
Cl 10(Hydaulic Proof Pressure Test)	-	0	-
Cl 9(Cover)	-	0	-
Cl 8(Lining)	-	0	-
Cl 7(Reinforcement)	-	0	-
Cl 6(Coil Dia)	-	0	-
Cl 5(Mass)	-	0	-
Cl 4(Length)	-	0	-
Cl 3.4(Internal Dia)	-	0	-
Cl 3.2 & 3.3(Nom ID)	-	0	-
Cl 3.1(Type)	-	0	-
Cl 3.1(Type)	-	0	-
Cl 3.2 & 3.3(Nom ID)	-	0	-
Cl 3.4(Internal Dia)	-	0	-
Cl 4(Length)	-	0	-
Cl 5(Mass)	-	0	-
Cl 6(Coil Dia)	-	0	-
Cl 7(Reinforcement)	-	0	-
Cl 8(Lining)	-	0	-
Cl 9(Cover)	-	0	-
Cl 10(Hydaulic Proof Pressure Test)	-	0	-
Cl 11(Hydraulic Burst Pressure Test)	-	0	-
Cl 12(Kink test)	-	0	-
Cl 13 & Annex A(Adhesion Test)	-	0	-
Cl 14 & Annex B(Abrasion Resistance Test)	-	0	-
Cl 15(Accelerated Ageing Test)	-	0	-
Cl 16(Change in Length)	-	0	-
Cl 17.1 & Annex C(Ozone Resistance Test)	-	0	-
Cl 17.2(Oil Resistance Test)	-	0	-
Cl 17.3(Heat Resistance Test)	-	0	-
Cl 17.3(Heat Resistance Test)	-	0	-
Cl 17.2(Oil Resistance Test)	-	0	-
Cl 17.1 & Annex C(Ozone Resistance Test)	-	0	-
Cl 16(Change in Length)	-	0	-
Cl 15(Accelerated Ageing Test)	-	0	-
Cl 14 & Annex B(Abrasion Resistance Test)	-	0	-
Cl 13 & Annex A(Adhesion Test)	-	0	-
Cl 12(Kink test)	-	0	-
Cl 11(Hydraulic Burst Pressure Test)	-	0	-
Cl 10(Hydaulic Proof Pressure Test)	-	0	-
Cl 9(Cover)	-	0	-
Cl 8(Lining)	-	0	-
Cl 7(Reinforcement)	-	0	-
Cl 6(Coil Dia)	-	0	-
Cl 5(Mass)	-	0	-
Cl 4(Length)	-	0	-
Cl 3.4(Internal Dia)	-	0	-
Cl 3.2 & 3.3(Nom ID)	-	0	-
Cl 3.1(Type)	-	0	-
Cl 17.3(Heat Resistance Test)	-	0	-
Cl 17.2(Oil Resistance Test)	-	0	-
Cl 17.1 & Annex C(Ozone Resistance Test)	-	0	-
Cl 16(Change in Length)	-	0	-
Cl 15(Accelerated Ageing Test)	-	0	-
Cl 14 & Annex B(Abrasion Resistance Test)	-	0	-
Cl 13 & Annex A(Adhesion Test)	-	0	-
Cl 12(Kink test)	-	0	-
Cl 11(Hydraulic Burst Pressure Test)	-	0	-
Cl 10(Hydaulic Proof Pressure Test)	-	0	-
Cl 9(Cover)	-	0	-
Cl 8(Lining)	-	0	-
Cl 7(Reinforcement)	-	0	-
Cl 6(Coil Dia)	-	0	-
Cl 5(Mass)	-	0	-
Cl 4(Length)	-	0	-
Cl 3.4(Internal Dia)	-	0	-
Cl 3.2 & 3.3(Nom ID)	-	0	-
Cl 3.1(Type)	-	0	-

-
Included w.e.f. 13.01.2025

IS 292 (1983)

Specification for leaded brass ingots and casting (Second Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3.1, Table no.1(Chemical composition)	-	10000	For complete testing
Cl. No.3.2(General compostion)	-	10000	For complete testing
Cl. No.4(pressure test)	-	10000	For complete testing
Cl. No.5(Freedom from defect)	-	10000	For complete testing
Cl. No.6(Size and shape)	-	10000	For complete testing
Cl. No.7(Marking)	-	10000.03	For complete testing
Cl.3.1(Copper+ incidental nickel -IS 3685)	-	10000	For complete testing
Cl.3.1(Lead - IS 3685)	-	10000	For complete testing
Cl.3.1(Iron -IS 3685)	-	10000	For complete testing
Cl.3.1(Aluminium - IS 3685)	-	10000	For complete testing
Cl.3.1(Zinc - IS 3685)	-	10000	For complete testing
Cl.3.1(Tin - IS 3685)	-	10000	For complete testing
5(FREEDOM FROM DEFECTS)	-	10000	For complete testing
6(Shape & size)	-	10000	For complete testing

-
Included w.e.f. 13.01.2025

IS 18573 (2024)

Cold formed welded carbon steel square and rectangular hollow sections for mechanical, general engineering and decorative purposes ï¿½ Specification

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Types)	-	500	For complete qualitative tests
Clause.4.0(Carbon)	-	1500	For complete chemical testing
Clause.4.0(Sulphur)	-	1500	For complete chemical testing
Clause.4.0(Sulphur)	-	1500	For complete chemical testing
Clause.4.0(Phosphorus)	-	1500	For complete chemical testing
Clause.4.0(Silicon)	-	1500	For complete chemical testing
Clause.4.0(Manganese)	-	1500	For complete chemical testing
Clause.5.0(Supply of Material)	-	500	For complete qualitative tests
Clause.5.0(Supply of Material)	-	500	For complete qualitative tests
Clause.6.0(Workmanship)	-	500	For complete qualitative tests
Clause.7.0(Straightness)	-	9400	For complete dimensional testing
Clause.8.0(Basis of Calculation)	-	9400	For complete dimensional testing
Clause.9.0(Length)	-	9400	For complete dimensional testing
Clause.10.0(Dimensions and properties)	-	9400	For complete dimensional testing
Clause.10.0(Dimensions and properties)	-	9400	For complete dimensional testing
Clause.11.0(General)	-	500	For complete qualitative tests
Clause.11.0(Outside Dimension)	-	9400	For complete dimensional testing
Clause.11.0(Thickness)	-	9400	For complete dimensional testing
Clause.11.0(Thickness)	-	9400	For complete dimensional testing
Clause.11.0(Concavity and Convexity)	-	9400	For complete dimensional testing
Clause.11.0(Squareness of Sides)	-	9400	For complete dimensional testing
Clause.11.0(External Corner Radiius)	-	9400	For complete dimensional testing
Clause.11.0(Straightness and twist)	-	9400	For complete dimensional testing
Clause.12.0(Dimension Tolerances)	-	9400	For complete dimensional testing
Clause.12.0(Dimension Tolerances)	-	9400	For complete dimensional testing
Clause.13.0(Surface Protection)	-	500	For complete qualitative test
Clause.14.0(Testing)	-	500	For complete qualitative tests
Clause.15.0(Tensile test)	-	3500	For complete mechanical testing
Clause.15.0(Yield strength)	-	3500	For complete mechanical testing
Clause.15.0(Elognation Percent)	-	3500	For complete mechanical testing
Clause.18.0(Marking)	-	500	For complete qualitative tests
6(Workmanship)	-	500	For complete qualitative tests
10(Dimensions and Properties)	-	9400	For complete dimensional testing
11(Measurement of Shape and Size)	-	9400	For complete dimensional testing
12(Dimensions and Tolerances)	-	9400	For complete dimensional testing
13(Surface Protection)	-	500	For complete qualitative tests
15(Tensile Test)	-	3500	For complete mechanical testing

-
-

IS 2403 (2024)

Short-Pitch Transmission Precision Roller and Bush Chains, Attachments and Associated Chain Sprockets (Fourth Revision)

Upto 1000 kN load, excluding chain no. 80 to 72B

113000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.3 Table-1,2(Dimensions- Pitch- p)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Roller diameter- d1)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Width between inner plates- b1)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Bearing pin body diameter- d2)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions-Bush bore-d3)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Chain path depth- h1)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions-Inner plate depth- h2)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions-Outer plate depth- h3)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Cranked link dimensions- l1)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Cranked link dimensions- l2)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Cranked link dimensions- c)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Transverse pitch- pt)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Width over inner link- b2)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Width between outer plates- b3)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Width over bearing pins- b4)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Width over bearing pins- b5)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Width over bearing pins- b6)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Dimensions- Additional width for joint fastener- b7)	-	62000	For complete dimension test and other qualitative tests
Cl-3.3 Table-1,2(Measuring force)	-	51000	For mechanical tests
Cl-3.3, 3.4.2 Table-1,2(Minimum tensile strength)	-	51000	For mechanical tests
Cl-3.4.3(Preloading)	-	51000	For mechanical tests
Cl-3.4.4(Length validation)	-	51000	For mechanical tests
Cl-3.4.5(Dynamic testing)	-	51000	For mechanical tests
Cl-3.5(Marking)	-	62000	For complete dimension test and other qualitative tests
Cl-3.6(Cranked links)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-3(Platform height h4)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-3(Minimum hole diameter d4)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-3(Traverse distance between hole centres f)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-4(Height from chain centre line h5)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-4(Minimum diameter of holes d4)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-5(Pin extension Type “X” b8)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-5(Pin extension Type “X” b5)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-5(Pin extensiona Type “Y” b10)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-5(Pin extensiona Type “Y” b9)	-	62000	For complete dimension test and other qualitative tests
Cl-4.4, Table-5(Pin diameter Types “X” and “Y” d2)	-	62000	For complete dimension test and other qualitative tests
Cl-4.6(Marking)	-	62000	For complete dimension test and other qualitative tests
Cl-5.3(Diametral dimensions of sprocket rim)	-	62000	For complete dimension test and other qualitative tests
Cl-5.4(Sprocket tooth gap forms)	-	62000	For complete dimension test and other qualitative tests
Cl-5.5(Tooth heights and tip diameters)	-	62000	For complete dimension test and other qualitative tests
Cl-5.6(Sprocket rim profiles)	-	62000	For complete dimension test and other qualitative tests
Cl-5.7(Radial run-out)	-	62000	For complete dimension test and other qualitative tests
Cl-5.8(Axial run-out (wobble))	-	62000	For complete dimension test and other qualitative tests
Cl-5.9(Pitch accuracy of sprocket teeth)	-	62000	For complete dimension test and other qualitative tests
Cl-5.10(Number of teeth)	-	62000	For complete dimension test and other qualitative tests
Cl-5.11(Bore tolerance)	-	62000	For complete dimension test and other qualitative tests
Cl-12(Marking)	-	62000	Exclusion Cl-5.6 (Sprocket rim profiles) Cl-5.9 (Pitch accuracy of sprocket teeth) Cl-5.11 (Bore tolerance), Dynamic Testing(CL 3.4.5)
Cl-3.3 Table-1,2(Dimensions- Pitch- p)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Roller diameter- d1)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Width between inner plates- b1)	-	0.03	-
Cl-3.3 Table-1,2(Dimensions- Bearing pin body diameter- d2)	-	0	-
Cl-3.3 Table-1,2(Dimensions-Bush bore-d3)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Chain path depth- h1)	-	0	-
Cl-3.3 Table-1,2(Dimensions-Inner plate depth- h2)	-	0	-
Cl-3.3 Table-1,2(Dimensions-Outer plate depth- h3)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Cranked link dimensions- l1)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Cranked link dimensions- l2)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Cranked link dimensions- c)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Transverse pitch- pt)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Width over inner link- b2)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Width between outer plates- b3)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Width over bearing pins- b4)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Width over bearing pins- b5)	-	0.03	-
Cl-3.3 Table-1,2(Dimensions- Width over bearing pins- b6)	-	0	-
Cl-3.3 Table-1,2(Dimensions- Additional width for joint fastener- b7)	-	0	-
Cl-3.3 Table-1,2(Measuring force)	-	0	-
Cl-3.3, 3.4.2 Table-1,2(Minimum tensile strength)	-	0	-
Cl-3.4.3(Preloading)	-	0	-
Cl-3.4.4(Length validation)	-	0	-
Cl-3.4.5(Dynamic testing)	-	0	-
Cl-3.5(Marking)	-	0	-
Cl-3.6(Cranked links)	-	0	-
Cl-4.4, Table-3(Platform height h4)	-	0	-
Cl-4.4, Table-3(Minimum hole diameter d4)	-	0	-
Cl-4.4, Table-3(Traverse distance between hole centres f)	-	0	-
Cl-4.4, Table-4(Height from chain centre line h5)	-	0	-
Cl-4.4, Table-4(Minimum diameter of holes d4)	-	0	-
Cl-4.4, Table-5(Pin extension Type “X” b8)	-	0	-
Cl-4.4, Table-5(Pin extension Type “X” b5)	-	0	-
Cl-4.4, Table-5(Pin extensiona Type “Y” b10)	-	0	-
Cl-4.4, Table-5(Pin extensiona Type “Y” b9)	-	0	-
Cl-4.4, Table-5(Pin diameter Types “X” and “Y” d2)	-	0	-
Cl-4.6(Marking)	-	0	-
Cl-5.3(Diametral dimensions of sprocket rim)	-	0	-
Cl-5.4(Sprocket tooth gap forms)	-	0	-
Cl-5.5(Tooth heights and tip diameters)	-	0	-
Cl-5.6(Sprocket rim profiles)	-	0	-
Cl-5.7(Radial run-out)	-	0	-
Cl-5.8(Axial run-out (wobble))	-	0	-
Cl-5.9(Pitch accuracy of sprocket teeth)	-	0	-
Cl-5.10(Number of teeth)	-	0	-
Cl-5.11(Bore tolerance)	-	0	-
Cl-12(Marking)	-	0	-

-
Included w.e.f. 13.01.2025 Exclusion: Cl-3.4.5 (Dynamic testing), Cl-5.6 (Sprocket rim profiles), Cl-5.9 (Pitch accuracy of sprocket teeth), Cl-5.11 (Bore tolerance)

100

IS 2403 (2014)

Short - Pitch transmission precision roller and bush chains, attachments and associated chain sprockets (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3.1, Table no.1(Chemical composition)	-	10000	For complete testing
Cl. No.3.2(General compostion)	-	10000	For complete testing
Cl. No.4(pressure test)	-	10000	For complete testing
Cl. No.5(Freedom from defect)	-	10000	For complete testing
Cl. No.6(Size and shape)	-	10000	For complete testing
Cl. No.7(Marking)	-	10000	For complete testing
Cl.3.1(Copper+ incidental nickel -IS 3685)	-	10000	For complete testing
Cl.3.1(Lead - IS 3685)	-	10000	For complete testing
Cl.3.1(Iron -IS 3685)	-	9999.98	For complete testing
Cl.3.1(Aluminium - IS 3685)	-	10000	For complete testing
Cl.3.1(Zinc - IS 3685)	-	10000	For complete testing
Cl.3.1(Tin - IS 3685)	-	10000	For complete testing
5(FREEDOM FROM DEFECTS)	-	10000	For complete testing
6(Shape & size)	-	10000	For complete testing

-
Included w.e.f. 13.01.2025

101

IS 2046 (1995)

Decorative thermosetting synthetic resinbonded laminated sheets specification (Second Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 , Table 1(CLASSIFICATION)	-	3500	For complete qualitative tests
5.1(Colour and Pattern)	-	3500	For complete qualitative tests
5.2(Surface Finish)	-	3500	For complete qualitative tests
5.2.2(Reverse side/Bonding)	-	3500	For complete qualitative tests
5.3 ,Table 5(Thickness)	-	3500	For complete qualitative tests
5.4(Appearance )	-	3500	For complete qualitative tests
5.2.2(Sports, dirt and similar surface defects)	-	3500	For complete qualitative tests
5.2.2(Fibres,hairs,scratches)	-	3500	For complete qualitative tests
5.2.2(Accumulated(Combination)of surface defects)	-	3500	For complete qualitative tests
5.2.2(Edge Defects)	-	3500	For complete qualitative tests
5.2.2(Broken Corners )	-	3500	For complete qualitative tests
5.4.4(Sanding Defects)	-	3500	For complete qualitative tests
5.4.5 table 6(W arping (Flatness ))	-	750	-
5.4.6 (Length and width of a full size Laminate)	-	750	-
5.4.6 (Length and width of a full size Laminate)	-	750	-
5.4.7,Fig. 2(Staightness of Edges)	-	750	-
5.4.8, Fig.3(Squareness of the Laminates)	-	750	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	1000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	750	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	1000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	1000	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	500	Additional charges, if required
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	500	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	1000	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	1000	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	300	Additional charges, if required
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	500	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	800	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	800	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	8000	-
5.5, Tables 7, Sr No.(x) Annex -O (alternative)(Resistance to colour change)	-	0	Resistance to color change, Table 7 as per annex N only (Exclusion for other alternative methods)
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	300	Additional charges, if required
5.5, Tables 7, Sr No.(xi) Annex -Q (alternative)(Resistance to Cigarette burns)	-	300	Additional charges, if required
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	500	Additional charges, if required
5.5, Tables 7, Sr No.(xiv) Annex -R (Formability Method B)	-	300	Additional charges, if required
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	300	Additional charges, if required
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method B)	-	500	Additional charges, if required
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	1500	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	1500	Additional charges, if required
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	1500	Additional charges, if required
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	1500	Additional charges, if required
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	1250	Additional charges, if required
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	1350	Additional charges, if required
7.2 a)(Marking)	-	3500	For complete qualitative tests
7.2 b)(Marking)	-	3500	For complete qualitative tests
7.2 c)(Marking)	-	3500	For complete qualitative tests
7.2 d)(Marking)	-	3500	For complete qualitative tests
7.2.1(Marking)	-	3500	For complete qualitative tests
5 & 5.1(Colour & Pattern)	-	0	-
5.2(Surface & Finish)	-	0	-
5.2.2(Reverse side Bonding)	-	0	-
5.3(Nominal thickness)	-	0	-
5.4.1.1(Surface defects)	-	0	-
5.4.1.2(Fiber hair scratches)	-	0	-
5.4.1.3(Accumulated(combinations) of surface defect)	-	0	-
5.4.2(Edge defect)	-	0	-
5.4.3(Broken corner)	-	0	-
5.4.4(Sanding defect)	-	0	-
5.4.5(Warping(Flatness))	-	0	-
5.4.6(Length)	-	0	-
5.4.6(Width)	-	0	-
5.4.7(Straightness of edge)	-	0	-
5.4.8(Squreness of laminate)	-	0	-
5.5Table-7(1(Surfacewear)	-	0	-
Table-7(2(Immesion in boiling water)	-	0	-
Table-7(3(Dry heat resistance)	-	0	-
Table-7(4(Dimensional stability)	-	0	-
Table-7(6(Impact by small dia.Ball)	-	0	-
Table-7(7(Impact by large dia.Ball)	-	0	-
Table-7(8(Cracking resistance)	-	0	-
Table-7(9(Scracting resistance)	-	0	-
Table-7(10(Staining resistance)	-	0	-
Table-7(10(Colour change(Xenon arc resis))	-	0	-
Table-7(11(Cigarette burn resistance)	-	0	-
Table-7(12(Formability)	-	0	-
Table-7(13(Blistering)	-	0	-
Table-7(14(Steam resistance)	-	0	-
Table-7(15(Crazing reistance)	-	0	-
Table-7(16(Moisture reistance)	-	0	-
Table-8(17(Flexural Modulus)	-	0	-
Table-8(18(Flexural strength)	-	0	-
Table-8(19(Tensile strength)	-	0	-

-
-

102

IS 6623 (2004)

High Strength Structural Nuts

M 12 To M 36/ Properly Class 85 & 105

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 Table-1(Dimensions- d)	-	5000	For complete dimesnions
4.1 Table-1(Dimensions- p)	-	5000	For complete dimensions
4.1 Table-1(Dimensions- da)	-	5000	For complete dimensions
4.1 Table-1(Dimensions- dw)	-	5000	For complete dimensions
4.1 Table-1(Dimensions- e)	-	5000	For complete dimensions
4.1 Table-1(Dimensions- m)	-	5000	For complete dimensions
4.1 Table-1(Dimensions- m')	-	5000	For complete dimensions
4.1 Table-1(Dimensions- m'')	-	5000	For complete dimensions
4.1 Table-1(Dimensions- c)	-	5000	For complete dimensions
4.1 Table-1(Dimensions- s)	-	5000	For complete dimensions
4.2(Conformity of threads)	-	750	-
5.1 Table-2(Rockwell Hardness)	-	500	-
5.1 Table-2(Proof Load Tcst)	-	5650	-
6.2(Finish)	-	3000	-

-
-

103

IS 12585 (2023)

SPECIFICATION FOR THERMOPLASTIC HOSES (TEXTILE REINFORCED) FOR WATER - GENERAL PURPOSE ( First Revision of IS 12585 )

35500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Materials and Construction)	-	2000	-
5(Materials and Construction)	-	2000	-
6.1(Dimensions (Inside diameters and tolerances on inside diameter))	-	2500	-
6.2(Concentricity)	-	1500	-
6.3(Tolerance on Length)	-	1500	-
6.4(Minimum Wall Thickness)	-	1500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Lining)	-	3500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Tensile Strength) - Cover)	-	3500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Lining)	-	3500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials (Minimum Elongation at break) - Cover)	-	3500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials-Resistance to ageing (Change in Tensile Strength from original value, max) -Lining)	-	3500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Tensile Strength from original value, max) -Cover)	-	5500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Lining)	-	5500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Resistance to ageing(Change in Elongation at break from original value, max) - Cover)	-	5500	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Lining)	-	2000	-
7, 7.1 -Table 2(Physical Properties-Thermoplastic materials - Loss in mass on heating- Cover)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 1)	-	2000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 2)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 23°C - Type 3)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 1)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 2)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 23°C - Type 3)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 1)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 2)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Proof Pressure at 60°C - Type 3)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 1)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 2)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Minimum Burst Pressure at 60°C - Type 3)	-	2500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Change in Length at maximum working pressure at 23°C (±8%))	-	3000	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - Adhesion between components)	-	5500	-
7, 7.2 -Table 3(Physical Properties-Finished Hoses - UV resistance (Xenon-arc lamp))	-	4000	-
7, 7.2 -Table 3(Flexibility at 23°C)	-	4000	-
7, 7.2 -Table 3(Low Temperature flexibility)	-	5500	-

-
Included w.e.f. 07.01.2026

104

IS 13713 (2021)

Plastic Chairs for General Purposes - Specification ( First Revision )

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Material)	-	500	-
5(Design)	-	400	-
6(Dimensions)	-	500	-
6 Table 1i a(Seat: Seat height)	-	500	-
6 Table 1i b(Seat: Effective seat depth)	-	500	-
6 Table 1i c(Seat: Seat width)	-	500	-
6 Table 1ii(Total height)	-	500	-
6 Table 1iii a(Total width (For chair with arms))	-	500	-
6 Table 1iii b(Total width (For chair without arms))	-	500	-
6 Table 1iv a(Total depth (For chair with arms))	-	500	-
6 Table 1iv b(Total depth (For chair without arms))	-	500	-
7(Mass)	-	400	-
8(Workmanship and finish)	-	500	-
9.1.1(Strength Test-static test)	-	500	-
9.1.1(Strength Test-fatigue test)	-	1500	-
9.1.1(Strength Test-Impact test)	-	1500	-
9.1.2(Stability Test)	-	1500	-
9.1.3(Free Fall Drop Test)	-	1600	-
9.1.4(Static Load Test for Leg Slippage and Distortion)	-	2500	-
9.1.5(Handle Impact Test)	-	1500	-
9.1.6(Vibration Test)	-	3000	-
9.1.7(Rigidity Test for Chair Shell)	-	2500	-
9.1.8(Colour Fastness to Daylight)	-	2500	-
9.1.9(Determination of Flammability by Oxygen Index)	-	2500	-

-
Included w.e.f. 07.01.2026

105

IS 2365 (2024)

STEEL WIRE ROPES FOR LIFTS - MINIMUM REQUIREMENTS (Third revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	250	-
Cl-4.1.1(Wire)	-	250	-
Cl-4.1.2(Core)	-	500	-
Cl-4.1.3(Lubricant)	-	500	-
Cl-4.2.2(Wire Joints)	-	200	-
Cl-4.2.3(Fibre Core Joints)	-	200	-
Cl-4.2.4(Lubrication)	-	250	-
Cl-4.2.5(Perforation and postformation)	-	250	-
Cl-4.2.7(Rope ends)	-	250	-
Cl-4.2.10, 4.2.11(Lay of Ropes)	-	250	-
Cl-4.4(Dimensions)	-	1000	-
Cl-4.5(Minimum Breaking force)	-	1500	-
Cl-4.6(Wire tensile strength, if required by purchaser)	-	1500	-
Cl-4.7(Rope stretch)	-	500	-
Cl-5.2.1(Equipment)	-	500	-
Cl-5.2.2(Measured diameter)	-	500	-
Cl-5.2.3(Ovality)	-	500	-
Cl-5.2.4(Variation)	-	250	-
Cl-5.3(Test on rope for breaking force)	-	2000	-
Cl-5.4(Test on rope for lubricant content)	-	500	-
Cl-5.5(Test on rope for wire tensile strength)	-	1500	-
Cl-5.6(Additional test)	-	1500	-
Cl-4.1(Material)	-	0	-
Cl-4.1.1(Wire)	-	0	-
Cl-4.1.2(Core)	-	0	-
Cl-4.1.3(Lubricant)	-	0	-
Cl-4.2.2(Wire Joints)	-	0	-
Cl-4.2.3(Fibre Core Joints)	-	0	-
Cl-4.2.4(Lubrication)	-	0	-
Cl-4.2.5(Perforation and postformation)	-	0	-
Cl-4.2.7(Rope ends)	-	0	-
Cl-4.2.10, 4.2.11(Lay of Ropes)	-	0	-
Cl-4.4(Dimensions)	-	0	-
Cl-4.5(Minimum Breaking force)	-	0	-
Cl-4.6(Wire tensile strength, if required by purchaser)	-	0	-
Cl-4.7(Rope stretch)	-	0	-
Cl-5.2.1(Equipment)	-	0	-
Cl-5.2.2(Measured diameter)	-	0	-
Cl-5.2.3(Ovality)	-	0	-
Cl-5.2.4(Variation)	-	0	-
Cl-5.3(Test on rope for breaking force)	-	0	-
Cl-5.4(Test on rope for lubricant content)	-	0	-
Cl-5.5(Test on rope for wire tensile strength)	-	0	-
Cl-5.6(Additional test)	-	0	-

-
Included w.e.f. 07.01.2026

106

IS 2347 (2023)

DOMESTIC PRESSURE COOKER ï¿½ SPECIFICATION

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Gross capacity)	-	28000	-
4.2(Body Capacity)	-	28000	-
5.1(Body, Lid, Containers and Grid)	-	28000	-
5.1.2(Body and Lid )	-	28000	-
5.1.3(Stainless steel pressure cooker)	-	28000	-
5.1.4(Aluminium cooker )	-	28000	-
5.2(Safety Relief Device)	-	28000	-
5.3(Gasket)	-	28000	-
5.4(Handles and Knobs)	-	28000	-
5.5(Pressure Regulating Device )	-	28000	-
5.6(Vent Seal Pin for Pressure Regulating Device )	-	28000	-
5.7(Vent Pipe )	-	28000	-
5.8(Vent Pipe Nut )	-	28000	-
5.9(Spring )	-	28000	-
5.1(Material of Rim )	-	28000	-
5.11(Visual Pressure Indicator)	-	28000	-
5.12(Gasket Release System)	-	28000	-
6(Construction)	-	28000	-
7(Workmanship and Finish )	-	28000	-
8.1(Air Pressure Test )	-	28000	-
8.2(Proof Pressure Test )	-	28000	-
8.3(Operating Test for Pressure Regulating Device )	-	28000	-
8.4(Test for Safety Relief Device )	-	28000	-
8.5(Bursting Pressure Test )	-	28000	-
8.6(Test for Removal of Lid under Pressure )	-	28000	-
8.7(Test for Spring Loaded Mechanism )	-	28000	-
8.8(Composite Cooker Base )	-	28000	-
8.9(Aluminium induction compatible Base )	-	28000	-
8.1(Handles of cooker )	-	28000	-
8.11(External Coating)	-	28000	-
8.12(Internal Coating )	-	28000	-
8.13(Integral electrical heating)	-	27999.99	-
8.14(Ply construction cooker Body )	-	28000	-
8.15.1(Fragmentation Test )	-	28000	-
8.15.2(Ball Drop Test )	-	28000	-
8.15.3(Thermal Shock Test )	-	28000	-
8.15.4(Free Fall Test)	-	28000	-
8.17(Test for Effectiveness for Induction Bottom)	-	28000	-
11(Marking )	-	28000	-
12(Packing )	-	28000	-
4(Capacity)	-	28000	-
4.2(Body Capacity)	-	27999.99	-
5.1.1(Body, Lid, Containers and Grid)	-	28000	-
5.1.2(Body, Lid, Containers and Grid)	-	28000	-
5.1.3(Body, Lid, Containers and Grid)	-	28000	-
5.1.4(Body, Lid, Containers and Grid)	-	28000	-
5.1.5(Body, Lid, Containers and Grid)	-	28000	-
5.2.1(Destructive Type Safety Relief Device)	-	28000	-
5.2.2(Resettable Type Safety Relief Device)	-	28000	-
5.3(Gasket)	-	28000	-
5.4(Handles and Knobs)	-	28000	-
5.5(Pressure Regulating Device)	-	28000	-
5.6(Vent Seal Pin for Pressure Regulating Device)	-	28000	-
5.7(Vent Pipe)	-	28000	-
5.8(Vent Pipe Nut)	-	28000	-
5.9(Spring)	-	28000	-
5.10(Spring)	-	28000	-
5.11(Visual Pressure Indicator)	-	28000	-
5.12(Gasket Release System)	-	28000	-
6(CONSTRUCTION)	-	28000	-
6.1(Pressure Regulating Device)	-	28000	-
6.1.1(Pressure Regulating Device)	-	28000	-
6.1.1(Minimum Inside diameter of Vent Pipe.)	-	28000	-
6.1.2(Pressure Regulating Device)	-	28000	-
6.1.3(Pressure Regulating Device)	-	28000	-
6.1.4(Pressure Regulating Device)	-	28000	-
6.1.5(Pressure Regulating Device)	-	28000	-
6.1.6(Pressure Regulating Device)	-	28000	-
6.2(Safety Relief Device)	-	28000	-
6.2.1(Safety Relief Device)	-	28000	-
6.2.2(Safety Relief Device)	-	28000	-
6.2.3(Safety Relief Device)	-	28000	-
6.3.1(Temperature Responsive Safety Relief Device)	-	28000	-
6.3.2(Temperature Responsive Safety Relief Device)	-	28000	-
6.3.3(Temperature Responsive Safety Relief Device)	-	28000	-
6.4.1(Handles and Knobs)	-	28000	-
6.4.1.1(Handles and Knobs)	-	28000	-
6.4.2(Handles and Knobs)	-	28000	-
6.4.2.1(Handles and Knobs)	-	28000	-
6.5(CONSTRUCTION)	-	28000	-
6.6(CONSTRUCTION)	-	28000	-
6.7(Internal Level Marking)	-	28000	-
6.8(Internal Level Marking)	-	28000	-
7.1(WORKMANSHIP AND FINISH)	-	28000	-
7.2(WORKMANSHIP AND FINISH)	-	28000	-
8.17(Test for Effectiveness for Induction Bottom)	-	28000	-
8.16(PRD with chain)	-	28000	-
8.15.4.2(Glass lid without rim)	-	28000	-
8.15.4.1("Free Fall Test ( Glass lid with rim) ")	-	28000	-
8.15.3(Thermal Shock Test on Tempered Glass lid)	-	28000	-
8.15.2(Ball Drop Test on Tempered Glass lid)	-	28000	-
8.15.1(Fragmentation Test on Tempered Glass lid)	-	28000	-
8.14(3 ply construction cooker body)	-	28000	-
8.13(Pressure cooker with integral electrical heating)	-	28000	-
8.12(Internal Coating)	-	28000	-
7.3(WORKMANSHIP AND FINISH)	-	28000	-
7.4(WORKMANSHIP AND FINISH)	-	28000	-
8.1(Air Pressure Test)	-	28000	-
8.2(Proof Pressure Test)	-	28000	-
8.3.1(Operating Test for Pressure Regulating Device)	-	28000	-
8.4.1(Test for Safety Relief Device)	-	28000	-
8.4.2(Test for Safety Relief Device)	-	28000	-
8.4.2 NOTE(Test for Safety Relief Device)	-	28000	-
8.5(Bursting Pressure Test)	-	28000	-
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	28000	-
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	28000	-
8.6.3(Tests for Removal of Lid under Pressure: For Cooker Fastened by Screw Clamps or Any Other Locking Device)	-	28000	-
8.6.4(Tests for Removal of Lid under Pressure in case of electrical pressure cooker)	-	28000	-
8.7(Test for Spring Loaded Mechanism)	-	28000	-
8.8(Test for stainless steel cookers)	-	28000	-
8.9("For stainless steel, aluminium induction compatible base and 3 ply cooker")	-	28000	-
8.10(Testing of Handles of the cooker)	-	28000	-
8.10 Note 3(Testing of Handles of the cooker)	-	28000	-
8.10 Note 4(Testing of Handles of the cooker)	-	28000	-
8.10 Note 5(Testing of Handles of the cooker)	-	28000	-
8.10 Note 6(Testing of Handles of the cooker)	-	27999.99	-
8.10.1(Testing of Handles of the cooker)	-	28000	-
8.11.1(External Coating)	-	27999.99	-
Cl 18.15.5 (Amendment No.2)(Nominal thickness of glass lid)	-	28000	-

-
Included w.e.f. 07.01.2026

107

IS 13114 (1991)

forged brass gate, globe and check valves for water works purposes

19850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Gate Valves)	-	19850	-
6.3(Globe valves)	-	19850	-
6.4(Check valves)	-	19850	-
7, Table- 2(Dimensions and Tolerances)	-	19850	-
8.1(Valve Bodies)	-	19850	-
8.1.1(Flow-way Area)	-	19850	-
8.1..2(Screwed body Ends)	-	19850	-
8.2(Discs and Wedges)	-	19850	-
8.3(Stuffing box)	-	19850	-
8.3.1(Gland)	-	19850	-
8.5(Direction of flow)	-	19850	-
8.6(operation )	-	19850	-
8.7(Stem)	-	19850	-
8.7.1(threads)	-	19850	-
8.7.2(Actuating threads )	-	19850	-
9.3(Hydrostatic Testing )	-	19850	-
Clause 8.1 and 9(Composition of copper(Electrolytic tough pitch copper))	-	19850	-
Clause 8.1 and 9((Composition of copper)Electrolytic tough pitch copper)	-	19850	-
Clause 8.1 and 9((Composition of copper)Electrolytic tough pitch copper)	-	19850	-
Clause 8.1 and 9((Composition of copper)Fire refined high conductivity copper)	-	19850	-
Clause 8.1 and 9((Composition of copper)Fire refined high conductivity copper)	-	19850	-
Clause 8.1 and 9((Composition of copper)Fire refined high conductivity copper)	-	19850	-
Clause 8.1 and 9((Composition of copper)Phosphorus deoxidized arsenical copper)	-	19850	-
Clause 8.1 and 9((Composition of Brass)Lead brass)	-	19850	-
Clause 8.1 and 9((Composition of Brass)Lead brass)	-	19850	-
Clause 8.1 and 9((Composition of Brass)Lead brass)	-	19850	-
Clause 8.1 and 9((Composition of Brass)Lead brass)	-	19850	-
Clause 8.1 and 9((Composition of Brass)lead Mn Brass)	-	19850	-
Clause 8.1 and 9((Composition of Brass)lead Mn Brass)	-	19850	-
Clause 8.1 and 9((Composition of Brass)lead Mn Brass)	-	19850	-
Clause 8.1 and 9((Composition of Brass)lead Mn Brass)	-	19850	-
Clause 8.1 and 9((Composition of Brass)lead Mn Brass)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-
Clause 8.1 and 9((Composition of bronze) Al.Si Bronze)	-	19850	-

-
Included w.e.f. 07.01.2026

108

IS 17682 (2021)

ALUMINIUM COMPOSITE PANEL SPECIFICATION

225000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 5.1(Polymer Granules)	-	20000	For dimension and other qualitative test
Clause 5.2(Aluminium Alloy Sheets)	-	20000	For dimension and other qualitative test
Clause 5.4(Surface Coating)	-	20000	For dimension and other qualitative test
Clause 6(DIMENSIONS AND TOLERANCE)	-	20000	For dimension and other qualitative test
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	10000	For density test
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	35000	For mechanical tests
"Clause 7.1 Table 2(iii)"(Yield strength)	-	35000	For mechanical tests
"Clause 7.1 Table 2(iv)"(Elongation)	-	35000	For mechanical tests
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	35000	For mechanical tests
"Clause 7.1 Table 3(i)"(Coating type)	-	20000	For dimension and other qualitative test
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	20000	For dimension and other qualitative test
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	20000	For dimension and other qualitative test
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	15000	For pencil hardness test
"Clause 7.1 Table 3(v)"(Gloss)	-	10000	For gloass test
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	225000	For weathermometer test (additional testing charges per hour as per applicability, if required), Rs. 150 per hour as per applicability including both long term duration tests
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	225000	For chemical resistance test (additional testing charges per hour as per applicability, if required) Rs. 150 per hour as per applicability including both long term duration tests
"Clause 7.1 Table 4(i)"(Limiting oxygen index (LOI), Min)	-	17000	For limiting oxygen index test
"Clause 7.1 Table 4(ii)"(Smoke density rating, percent, Max)	-	15000	For smoke density test
"Clause 7.1 Table 4(iii)"(Ignitability)	-	15000	For ignitability test
"Clause 7.1 Table 4(iv)"(Flame spread)	-	12000	For flame spread test
"Clause 7.1 Table 4(v)"(Non-combustibility (see Note))	-	7000	For Non-combustility test
"Clause 7.1 Table 4(vi)"(Oxygen bomb calorimeter)	-	15000	For oxygen bomb calorimeter test
"Clause 7.2 Table 5(i)"(Sound transmission class (STC), dB, Min)	-	0	Except Clause 7.2 Table 5(i) (Sound transmission class (STC), dB, Min) Sound transmission class
"Clause 7.2 Table 5(ii)"(Sound absorption coefficient, percent, Min)	-	0	Except Clause 7.2 Table 5(ii) (Sound absorption coefficient, percent, Min) Sound absorption coefficient Facilit
"Clause 7.2 Table 5(iii)"(Coefficient of linear thermal expansion, °C–1 , Max)	-	7000	For thermal expansion test
"Clause 7.2 Table 5(iv)"(Thermal Conductivity (W/m2 K), Max)	-	20000	For the thermal conductivity test
Clause 5.1(Polymer Granules)	-	2000	For dimension and other qualitative test
Clause 5.2(Aluminium Alloy Sheets)	-	20000	For dimension and other qualitative test
Clause 5.4(Surface Coating)	-	20000	For dimension and other qualitative test
Clause 6(DIMENSIONS AND TOLERANCE)	-	20000	For dimension and other qualitative test
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	10000	For density test
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	35000	For mechanical test
"Clause 7.1 Table 2(iii)"(Yield strength)	-	35000	For mechanical test
"Clause 7.1 Table 2(iv)"(Elongation)	-	35000	For mechanical test
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	35000	For mechanical test
"Clause 7.1 Table 3(i)"(Coating type)	-	19999.99	For dimension and other qualitative test
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	20000	For dimension and other qualitative test
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	20000.03	For dimension and other qualitative test
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	15000	For pencil hardness test
"Clause 7.1 Table 3(v)"(Gloss)	-	10000.01	For gloass test
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	22000	For weathermometer test
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	15000	For chemical resistance test
"Clause 7.1 Table 4(i)"(Limiting oxygen index (LOI), Min)	-	15000	For oxygen bomb calorimeter test
"Clause 7.1 Table 4(ii)"(Smoke density rating, percent, Max)	-	15000	For smoke density test
"Clause 7.1 Table 4(iii)"(Ignitability)	-	15000	For ignitability test
"Clause 7.1 Table 4(iv)"(Flame spread)	-	12000	For flame spread test
"Clause 7.1 Table 4(v)"(Non-combustibility (see Note))	-	7000	For Non-combustility test
"Clause 7.1 Table 4(vi)"(Oxygen bomb calorimeter)	-	15000	For oxygen bomb calorimeter test
"Clause 7.2 Table 5(i)"(Sound transmission class (STC), dB, Min)	-	8000	For sound transmission class
"Clause 7.2 Table 5(ii)"(Sound absorption coefficient, percent, Min)	-	8000	For sound absorption test
"Clause 7.2 Table 5(iii)"(Coefficient of linear thermal expansion, °C–1 , Max)	-	7000	For thermal expansion test
"Clause 7.2 Table 5(iv)"(Thermal Conductivity (W/m2 K), Max)	-	19999.99	For the thermal conductivity test
Clause 5.1(Polymer Granules)	-	20000	For dimension and other qualitative test
Clause 5.2(Aluminium Alloy Sheets)	-	20000	For dimension and other qualitative test
Clause 5.4(Surface Coating)	-	20000	For dimension and other qualitative test
Clause 6.1(Normal dimensions)	-	20000.02	For dimension and other qualitative test
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	9999.99	For density test
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	35000	For mechanical test
"Clause 7.1 Table 2(iii)"(Yield strength)	-	35000	For mechanical test
"Clause 7.1 Table 2(iv)"(Elongation)	-	35000	For mechanical test
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	35000	For mechanical test
"Clause 7.1 Table 3(i)"(Coating type)	-	20000	For dimension and other qualitative test
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	19999.98	For dimension and other qualitative test
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	10000	For dimension and other qualitative test
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	15000	For pencil hardness test
"Clause 7.1 Table 3(v)"(Gloss)	-	10000.02	For gloss test
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	22000	For weathermometer test
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	15000	For chemical resistance test
"Clause 7.1 Table 4(i)"(Limiting oxygen index (LOI), Min)	-	15000.02	For limiting oxygen index test
"Clause 7.1 Table 4(ii)"(Smoke density rating, percent, Max)	-	15000.03	For smoke density test
"Clause 7.1 Table 4(iii)"(Ignitability)	-	15000.01	For ignitability test
"Clause 7.1 Table 4(iv)"(Flame spread)	-	12000	For flame spread test
"Clause 7.1 Table 4(v)"(Non-combustibility (see Note))	-	7000.02	For Non-combustility test
"Clause 7.1 Table 4(vi)"(Oxygen bomb calorimeter)	-	15000.02	For oxygen bomb calorimeter test
"Clause 7.2 Table 5(i)"(Sound transmission class (STC), dB, Min)	-	8000	For sound transmission class test
"Clause 7.2 Table 5(ii)"(Sound absorption coefficient, percent, Min)	-	8000	For sound absorption test
"Clause 7.2 Table 5(iii)"(Coefficient of linear thermal expansion, °C–1 , Max)	-	7000	Fot thermal expansion test
"Clause 7.2 Table 5(iv)"(Thermal Conductivity (W/m2 K), Max)	-	20000.02	For the thermal conductivity test
Cl-6.2(Thickness)	-	20000.02	For dimension and other qualitative test
Cl-6.3(Tolerances)	-	20000	For dimension and other qualitative test
Cl-5.3(Adhesive)	-	20000	For dimension and other qualitative test
Cl-6(Edge straightness, Max)	-	20000	For dimension and other qualitative test
Cl-6(Squareness, Max)	-	20000	For dimension and other qualitative test
Tale 3 vi (Amendment No.1)(Chemical resistance a) HCl)	-	20000	-
Tale 3 vi (Amendment No.1)(Chemical resistance b) NaOH)	-	20000	-
Tale 3 vi (Amendment No.1)(Chemical resistance c) Mortar pat test, 24 h)	-	20000	-
Tale 3 vi (Amendment No.1)(Chemical resistance d) Detergent 3 percent solution (at 38 ⁰C for 72 h))	-	20000	-
Tale 3 vi (Amendment No.1)(Chemical resistance e) 70 percent nitric acid, 30 minute)	-	20000	-

-
-

109

IS 210 (2009)

Grey iron castings - Specification (First Revision)

FG 150, FG 200, FG 220, FG 260, FG 300, FG 350, FG 400

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	2750	For dimensions, tensile and Workmanship (if required)
16, Table 3(Hardness Test)	-	450	-
7.1(WORKMANSHIP AND FINISH)	-	2750	For dimensions, tensile and Workmanship (if required)
13(SIZE OF TEST BARS-Diameter)	-	2750	For dimensions, tensile and Workmanship (if required)
10.1(FREEDOM FROM DEFECTS)	-	2750	For dimensions, tensile and Workmanship (if required)
10.2(FREEDOM FROM DEFECTS)	-	2750	For dimensions, tensile and Workmanship (if required)
17,Annex B(TRANSVERSE TEST)	-	0	Exclusion of transverse test

-
-

110

IS 710 (2024)

MARINE PLYWOOD - SPECIFICATION (Third Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Timber)	-	0	-
Cl-4.2(Adhesive)	-	0	-
Cl-5.1(Veneers)	-	0	-
Cl-5.2.1(Glueing)	-	0	-
Cl -5.2.2(Thickness of Veneers)	-	1500	For complete dimensional test
Cl - 5.2.3.1(Joint in Veneers)	-	0	-
Cl - 5.2.3.2(Edge joints)	-	1500	For complete dimensional test
Cl - 5.2.3.3(End joints)	-	1500	For complete dimensional test
Cl - 5.2.3.4(Scarf joints)	-	1500	For complete dimensional test
Cl - 5.2.4(Grain Direction)	-	0	-
Cl-5.3(Treatment)	-	0	-
Cl-5.4(Moisture Content)	-	1000	-
Cl-6.1(Dimensions (length))	-	1500	For complete dimensional test
Cl-6.2(Thickness)	-	1500	For complete dimensional test
Cl-6.3(Squareness)	-	1500	For complete dimensional test
Cl-7.1, 7.2, 7.3, 7.4, 7.5 & 7.6(Workmanship and finish)	-	1500	For complete dimensional test
Cl-9.3(Moisture Content)	-	500	-
Cl-9.4.2(Glue Adhesion in Dry State- Adhesion of Plies)	-	500	-
Cl-9.4.1(Glue Adhesion in Dry State- Glue Shear Strength -Average)	-	500	-
Cl-9.5.1.1(Glue Adhesion in Water Resistance - Glue Shear Strength -Average)	-	500	-
Cl-9.5.1.2(Water Resistance Test-Adhesion of plies)	-	500	-
Cl-9.5.2(Water Resistance Test)	-	500	-
Cl-9.6(Tensile Strength-Along the grain)	-	1000	-
Cl-9.7(Mycological Test -Adhesion)	-	1000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	1000	-
Cl-9.8, Table-2(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	1000	-
Cl-9.9, Table-3 (i) a((Modulus of Elasticity: Across the Face Grain: Average) Wet Bending)	-	1000	-
Cl-9.9, Table-3 (i) b((Modulus of Elasticity: Across the Face Grain: Minimum Individual) Wet Bending)	-	1000	-
Cl-9.10(Retention of Preservative)	-	1500	-
Cl-9.11(Formaldehyde Content Test)	-	1500	-
Cl-9.12(Steady-State Formaldehyde Emission Test)	-	0	Exclusion
Cl-9.4.2(Adhesion of Plies)	-	500	-
5.1.1(Defects in veneers)	-	0	-

-
-

111

IS 4990 (2024)

PLYWOOD FOR CONCRETE SHUTTERING WORKS SPECIFICATION (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Timber)	-	0	Raw material testing additional, if required
Cl-5.2(Adhesives for Bonding of Veneers)	-	8000	Resin testing charges additional, if required, For BWP Grade 8000
Cl-6.1(Manufacture)	-	500	For Complete Qualitative Tests
Cl-6.2(Manufacture ( Thickness of veneers))	-	500	For Complete Qualitative Tests
Cl-6.3(Manufacture ( Physical and mechanical properties of veneers))	-	500	For Complete Qualitative Tests
Cl-6.4, 6.7(Manufacture (Plywood for concrete shuttering))	-	500	For Complete Qualitative Tests
Cl-6.5(Manufacture (Scarf joints))	-	500	For Complete Qualitative Tests
Cl-6.6(Manufacture ( Preservative treatment))	-	500	For Complete Qualitative Tests
Cl-7.1(Dimensions -length)	-	500	For complete dimensional tests
Cl-7.2(Thickness)	-	500	For complete dimensional tests
Cl-7.3(Squareness)	-	500	For complete dimensional tests
Cl-8.1, 8.2(Workmanship and finish)	-	500	For Complete Qualitative Tests
Cl-10.3(Moisture Content)	-	500	-
Cl-10.4.1(Glue Adhesion in Dry State - Glue Shear Strength-WOOD FAILURE, Average)	-	500	-
Cl-10.4.2(Glue Adhesion in Dry State - Adhesion of Plies)	-	500	-
Cl-10.5, 10.5.1(Resistance to water test- glue shear strength- WOOD Failure, Average)	-	1500	-
Cl-10.5.1.1(Water Resistance Test-Glue shear strength)	-	1000	-
Cl-10.5.1.2(Water Resistance Test-Adhesion of plies)	-	500	-
Cl-10.5.2(Water Resistance Test (Alternate method))	-	0	-
Cl-10.6(Water resistance test (Concrete shuttering Plywood))	-	750	-
Cl-10.7.1, Table-2(Mycological Test- Glue shear strengt)	-	750	-
Cl-10.7.2(Mycological Test- Adhesion of plies)	-	500	-
Cl-10.8(Tensile Strength)	-	1000	-
Cl-10.9, Table-3 (i)(Along (parallel to the grain direction of the face veneer))	-	1000	-
Cl-10.9, Table-3 (ii)(Across (perpendicular to the grain direction of the face veneer))	-	1000	-
Cl-10.10, Table-4 (i) a((Modulus of Elasticity: Across the Face Grain: Average) Wet Bending)	-	1000	-
Cl-10.10, Table-4 (i) b((Modulus of Rupture: Across the Face Grain: Minimum Individual) Wet Bending)	-	1000	-
Cl-10.11(Retention of Preservative)	-	1000	-
Cl-10.12(Formaldehyde Content Test)	-	1500	-
Cl-10.13(Steady-State Formaldehyde Emission Test)	-	0	Exclusion

-
-

112

IS 14846 (2000)

Sluice valve for water works purposes (50 To 1200 mm size) - specification

For Size 50 to 700 mm only

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Nominal Sizes)	-	6000	* 13000 for complete testing upto and including 100 mm * 17000 for complete testing from 125 mm and including 300 mm 21500 for complete testing from 350 mm and including 600 mm 24500 for above 600 mm
5.1.1(Actual Bore)	-	6000	* 13000 for complete testing upto and including 100 mm * 17000 for complete testing from 125 mm and including 300 mm 21500 for complete testing from 350 mm and including 600 mm 24500 for above 600 mm
10.1 Annex B-1(Hydraulic Test)	-	4000	For Cl 10 For complete Sizes, Dimensions and Visual aspects
10.2(Flaw Detection Test for Stems)	-	750	For Cl 10
9(Coating)	-	750	Cl cl 5 , Cl 7 and cl 9
4(Nominal Pressures)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.2.1(Manufacture - Bodies and Bonnets)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.7.1 Table 2,3(Dimension of Stem and Wedge Nuts)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.7.1 Table 2,3(Dimension of Stem and Wedge Nuts)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.7.1 Table 2,3(Dimension of Stem and Wedge Nuts)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.7.1 Table 2,3(Dimension of Stem and Wedge Nuts)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.13 Table 2, 3(Stuffing Box )	-	6000	For complete Sizes, Dimensions and Visual aspects
7.13 Table 2, 3(Stuffing Box )	-	6000	For complete Sizes, Dimensions and Visual aspects
7.13 Table 2, 3(Stuffing Box )	-	6000	For complete Sizes, Dimensions and Visual aspects
7.13 Table 2, 3(Stuffing Box )	-	6000	For complete Sizes, Dimensions and Visual aspects
7.11(Hand Wheel)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.11(Hand Wheel)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.11(Hand Wheel)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.12(Valve Caps)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.12(Valve Caps)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.12(Valve Caps)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 1(Flanges)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 2(Flanges)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 3(Flanges)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 4(Flanges)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 5(Flanges)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.3 Table 3A 6(Flanges)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.6 Table 4(Facing or Seat Rings)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.6 Table 4(Facing or Seat Rings)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.6 Table 4(Facing or Seat Rings)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.6 Table 4(Facing or Seat Rings)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.4.1(Wedges )	-	6000	For complete Sizes, Dimensions and Visual aspects
7.4.1(Wedges)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.4.1(Wedges)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.5(Guides and Lugs)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.5(Guides and Lugs)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.7.2(Stem and Wedge Nuts)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.7.4(Stem and Wedge Nuts)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.7.3(Stem and Wedge Nuts)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.1(Gears)	-	6000	For complete Sizes, Dimensions and Visual aspects
7.14(By Pass Arrangements)	-	6000	For complete Sizes, Dimensions and Visual aspects
10.1 Annex B-2(Hydraulic Test)	-	4000	For cl 10
7.5.1(Guides and Lugs)	-	6000	* 13000 for complete testing upto and including 100 mm * 17000 for complete testing from 125 mm and including 300 mm 21500 for complete testing from 350 mm and including 600 mm 24500 for above 600 mm

-
-

113

IS 5312 : Part 1 (2004)

Swing Check Type Reflux (Non-Return] Valves for Water Works Purposes - Part 1 : Single-Door Pattern

For Size 50 to 700mm only

8550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Nominal Sizes)	-	6050	•⁠ ⁠8550 for complete testing upto and including 100 mm •⁠ ⁠13000 for complete testing from 125 mm and including 300 mm * 18500 for complete testing from 350 mm and including 600 mm •⁠ ⁠22500 for above 600 mm
4.1.1(Actual bore)	-	6050	For Complete Mechanical Dimension
7.1(Coating)	-	6050	For Complete Mechanical Dimension
8.2(Hydrostatic Body Test )	-	2500	For complete Hydrostatic
8.3(Hydrostatic Seat Test)	-	2500	For Complete Hydrostatic Test
6.2(Manufacture Dimensions Table 2 )	-	6050	For Complete Mechanical Dimension
6.2(Manufacture Dimensions Table 2 )	-	6050	For Complete Mechanical Dimension
6.9(Manufacture )	-	6050	For Complete Mechanical Dimension
6.9(Manufacture )	-	6050	For Complete Mechanical Dimension
6.9(Manufacture )	-	6050	For Complete Mechanical Dimension
6.9(Manufacture )	-	6050	For Complete Mechanical Dimension
6.9(Manufacture )	-	6050	For Complete Mechanical Dimension
6.4(Manufacture )	-	6050	For Complete Mechanical Dimension
6.5(Manufacture )	-	6050	For Complete Mechanical Dimension
6.6(Manufacture )	-	6050	For Complete Mechanical Dimension
6.7(Manufacture )	-	6050	For Complete Mechanical Dimension
6.8(Manufacture )	-	6050	For Complete Mechanical Dimension
6.8.1(Manufacture )	-	6050	For Complete Mechanical Dimension
6.10(Manufacture )	-	6050	For Complete Mechanical Dimension
6.10.1(Manufacture )	-	6050	For Complete Mechanical Dimension
6.12(Door Faces)	-	6050	For Complete Mechanical Dimension
6.13(By-pass arrangements)	-	2500	For Complete Hydrostatic Testing
3(Nominal Pressure)	-	7500	•⁠ ⁠8550 for complete testing upto and including 100 mm •⁠ ⁠13000 for complete testing from 125 mm and including 300 mm * 18500 for complete testing from 350 mm and including 600 mm •⁠ ⁠22500 for above 600 mm

-
-

114

IS 19315 (2025)

Ball Valves for Water Works Purposes - Specification

8 mm and above

19850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 3(TERMS AND DEFINITION)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable) , Size: 8mm and above
As per Clause 3.1(Ambient Temperature)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
As per Clause 3.2(Cold Working Pressure (CWP))	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 3.3(DN)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 3.4(End-to-End Dimension)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 3.5(Face-to-Face Dimension)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 3.6(Full Bore Valve)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 3.7(Operator)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 3.8(PN or Class)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 3.9(Reduce Bore Valve)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 3.10(Trim)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4(DESIGN)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.1(Ball Valve Construction)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.2(Nominal Sizes)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.3(Rating)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.4(Valve Bore Dimensions)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.5(Face-to-Face and End-to-End Dimensions)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.6(Valve Ends)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.6.1(Flanged End)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.6.2(Socket Weld Ends for Stainless Steel Materials)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.6.3(Solder Ends for Copper Alloy Materials)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.6.4(Screwed Ends)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.6.4.1(Screwed end for copper alloy materials)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.6.4.2(Screwed end for stainless steel materials)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.6.5(Crimping Ends for Copper Alloy materials)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7(Design)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.1(General)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.1.2("Body shell thickness for copper alloy materials ")	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.1.3(Joint)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.1.5(End connections)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.1.6(Stems)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.1.8(Stem packing)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.1.9(Corrosion resistant coating)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.2(Body Shell Thickness for Steel Valves)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.3(Body Shell Thickness)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.4(Bolted Body Joint)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 4.7.5(Bolted Bonnet or Cover Joint)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 5(VALVE OPERATION)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 6(MATERIALS OF CONSTRUCTION)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7(PERFORMANCE REQUIREMENTS)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.2(Pressure Tests for Steel Valves)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.2.1(Shell Test (HYD))	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.2.2(Closure Test (HYD))	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.2.3(Closure Test (Gas))	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.2.4(Test Duration)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.3(Pressure Tests for Copper Alloy Valves)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.3.1(Shell Test)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.3.2(Closure Test)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.4(Test Fluid)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 7.5(Test Gauges)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 8(SAMPLING AND TESTING)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 8.2(Factory Production Control)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 9(PACKAGING)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 10(MARKING)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 10.1(Legibility)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 10.2(Body Marking)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)
Cl 10.3(Identification Plate)	-	19850	9850 (For mechanical test) + 10,000 for chemical (additional sample will be provided where applicable)

-
-

115

IS 2603 (1983)

Specification for copper anodes for electroplating (First Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.2.1, Table no.1(i)("Copper ( any silver pIesent to he counted as copper )")	-	6000	-
Cl. No.2.1,Table no.1(ii)(Bismith)	-	6000	-
Cl. No.2.1,Table no.1(iii)(Lead)	-	6000	-
Cl. No.2.1,Table no.1(iv)("Total of all impurities excluding oxygen and silver, Max")	-	6000	-
Cl. No.3(SHAPE AND SIZE)	-	4000	-
Cl. No.4(FREEDOM FROM DEFECTS)	-	2000	-
Cl. No.5(MARKING)	-	2000	-
Cl. No.2.1, Table no.1(i)("Copper ( any silver pIesent to he counted as copper )")	-	-	-
Cl. No.2.1,Table no.1(ii)(Bismith)	-	-	-
Cl. No.2.1,Table no.1(iii)(Lead)	-	-	-
Cl. No.2.1,Table no.1(iv)("Total of all impurities excluding oxygen and silver, Max")	-	-	-
Cl. No.3(SHAPE AND SIZE)	-	-	-
Cl. No.4(FREEDOM FROM DEFECTS)	-	-	-
Cl. No.5(MARKING)	-	-	-

-
Included w.e.f 31.12.2025

116

IS 1660 (2024)

Wrought and Cast Aluminium Utensils Specification ( Second Revision )

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	10000	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	10000	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	10000	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	10000	-
Cl-4.1(Main body of utensil)	-	10000	-
Cl-4.1(Cast cookware)	-	10000	-
Cl-4.1(Other aluminum components and parts)	-	10000	-
Cl-4.1.1(Lids (material))	-	10000	-
Cl-4.1.1(Minimum thickness of lid)	-	10000	-
Cl-4.1.2(Minimum thickness of glass)	-	10000	-
Cl-4.1.2(Material of rim)	-	10000	-
Cl-4.1.2(Minimum thickness of rim)	-	10000	-
Cl-4.2(Material of strips)	-	10000	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	10000	-
Cl-4.3(Clips of lunch box)	-	10000	-
Cl-4.3(Clips of lunch box)	-	10000	-
Cl-4.3(Rivets used in lunch box)	-	10000	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	10000	-
Cl-4.5(Rivets for fixing of handles)	-	10000	-
Cl-4.5(Material of cap)	-	10000	-
Cl-4.6(Strips used for flame guards)	-	10000	-
Cl-4.6(stainless steel)	-	10000	-
Cl-5(Fabrication)	-	10000	-
Cl-6(Shape and Dimensions)	-	10000	-
Cl-7.1(Handles, when fitted)	-	10000	-
Cl-7.2(Handles)	-	10000	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	10000	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	10000	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	10000	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	10000	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	10000	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	10000	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	10000	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	10000	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	10000	10000 – For complete testing, 9500 additional for cycle tests, if required.
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	10000	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	10000	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	10000	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	10000	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	10000	-
Cl-8(Workmanship and Finish)	-	10000	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	10000	-
Cl-8.3(Minimum nominal thickness)	-	10000	-
Cl-8.3(Thickness of hard anodized)	-	10000	-
Cl-8.3(Finish and appearance of hard anodized)	-	10000	-
Cl-8.3(Abrasion resistance of hard anodized)	-	10000	-
Cl-8.3(Colour of hard anodized)	-	10000	-
Cl-8.3(Hardness of hard anodized)	-	10000	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	10000	-
Cl-8.5(Non-stick unreinforced PTFE)	-	10000	-
Cl-8.6(Ceramic coating)	-	10000	-
Cl-8.7(The thickness test, adhesion test)	-	10000	-
Cl-8.7(Minimum thickness of coating)	-	10000	-
Cl-8.7.1(Dry heat the cookware)	-	10000	-
Cl-8.8(Requirements of PTFE)	-	10000	-
Cl-8.9(Material for induction plate)	-	10000	-
Cl-8.9(Test for Induction compatible base)	-	10000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	10000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	10000	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	10000	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	10000	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	10000	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	10000	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	10000	-
Cl-9.1(Normal Capacity)	-	10000	-
Cl-9.2(Normal Capacity of internal diameter)	-	10000	10000 – For complete testing, 9500 additional for cycle tests, if required.
Cl 3.1.4 Table 3 (Amendment No.1)(Thickness of cast cookware- Cast Aluminium- Minimum Base Thickness of Body)	-	10000	10000 – For complete testing, 9500 additional for cycle tests, if required.

-
-

117

IS 2016 (1967)

Specification for plain washers (First Revision)

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Material)	-	5500	For complete testing
2.2(Workmanship)	-	5500	For complete testing
3(Designation)	-	5500	For complete testing
4(Dimensions)	-	5500	For complete testing
5(Finish)	-	5500	For complete testing
7(Marking)	-	5500	For complete testing

-
Included w.e.f 16.12.2025

118

IS 4996 (1984)

Specification for reinforced concrete fence posts (First Revision)

39950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(MANUFACTURE-Construction and Finish )	-	39950	For complete testing
4.1.2(MANUFACTURE-Construction and Finish )	-	39950	For complete testing
4.2.1(MANUFACTURE-Reinforcement-Preparation)	-	39950	For complete testing
4.2.1(MANUFACTURE-Reinforcement-Preparation)	-	39950	For complete testing
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	39950	For complete testing
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	39950	For complete testing
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	39950	For complete testing
4.2.3(MANUFACTURE-Reinforcement-Anchorage)	-	39950	For complete testing
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	39950	For complete testing
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	39950	For complete testing
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	39950	For complete testing
4.2.4.1(MANUFACTURE-Reinforcement-Cover)	-	39950	For complete testing
5(SHAPE AND DIMENSIONS)	-	39950	For complete testing
7.1(STRENGTH OF REINFORCED CONCRETE FENCE POSTS-Impact Test)	-	39950	For complete testing
7.2(STRENGTH OF REINFORCED CONCRETE FENCE POSTS-Static Load Test)	-	39950	For complete testing
4.1.1(MANUFACTURE-Construction and Finish )	-	0	-
4.1.2(MANUFACTURE-Construction and Finish )	-	0	-
4.2.1(MANUFACTURE-Reinforcement-Preparation)	-	0	-
4.2.1(MANUFACTURE-Reinforcement-Preparation)	-	0	-
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	0	-
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	0	-
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	0	-
4.2.3(MANUFACTURE-Reinforcement-Anchorage)	-	0	-
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	0	-
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	0	-
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	0	-
4.2.4.1(MANUFACTURE-Reinforcement-Cover)	-	0	-
5(SHAPE AND DIMENSIONS)	-	0	-
7.1(STRENGTH OF REINFORCED CONCRETE FENCE POSTS-Impact Test)	-	0	-
7.2(STRENGTH OF REINFORCED CONCRETE FENCE POSTS-Static Load Test)	-	0	-
4.1.1(MANUFACTURE-Construction and Finish )	-	0	-
4.1.2(MANUFACTURE-Construction and Finish )	-	0	-
4.2.1(MANUFACTURE-Reinforcement-Preparation)	-	0.02	-
4.2.1(MANUFACTURE-Reinforcement-Preparation)	-	0	-
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	0.01	-
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	0	-
4.2.2(MANUFACTURE-Reinforcement-Positioning)	-	0	-
4.2.3(MANUFACTURE-Reinforcement-Anchorage)	-	0	-
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	0	-
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	0	-
4.2.4(MANUFACTURE-Reinforcement-Cover)	-	0	-
4.2.4.1(MANUFACTURE-Reinforcement-Cover)	-	0	-
5(SHAPE AND DIMENSIONS)	-	0	-
7.1(STRENGTH OF REINFORCED CONCRETE FENCE POSTS-Impact Test)	-	0	-
7.2(STRENGTH OF REINFORCED CONCRETE FENCE POSTS-Static Load Test)	-	0	-

-
Included w.e.f 16.12.2025

119

IS 7608 (1987)

Specification for phosphor bronze wire for general engineering purposes (First Revision)

29950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3(Supply of material)	-	29950	For complete testing
Clause 4(Freedom from defects)	-	29950	For complete testing
Clause 5(Condition)	-	29950	For complete testing
Clause 6.1(Chemical Composition)	-	29950	For complete testing
Clause 6.2(Chemical Composition)	-	29950	For complete testing
Clause 7.1(Tensile test)	-	29950	For complete testing
Clause 7.2(Wrapping test)	-	29950	For complete testing
Clause 8.1(Dimension)	-	29950	For complete testing
Clause 8.2(Tolerances)	-	29950	For complete testing
Clause 8.3(Measurement)	-	29950	For complete testing
Clause 9(Sampling and criteria for conformity)	-	29950	For complete testing
Clause 3(Supply of material)	-	-	-
Clause 4(Freedom from defects)	-	-	-
Clause 5(Condition)	-	-	-
Clause 6.1(Chemical Composition)	-	-	-
Clause 6.2(Chemical Composition)	-	-	-
Clause 7.1(Tensile test)	-	-	-
Clause 7.2(Wrapping test)	-	-	-
Clause 8.1(Dimension)	-	-	-
Clause 8.2(Tolerances)	-	-	-
Clause 8.3(Measurement)	-	-	-
Clause 9(Sampling and criteria for conformity)	-	-	-

-
Included w.e.f 16.12.2025

120

IS 17111 (2025)

HEAT-TREATABLE STEELS, ALLOY STEELS AND FREE-CUTTING STEELS - BALL AND ROLLER BEARING STEELS ( First Revision )

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause-6.3.1(Heat-treatment condition)	-	12000	For complete testing
Clause-6.3.2(Particular surface conditions)	-	12000	For complete testing
Clause-6.3.3(Traceability of the cast)	-	12000	For complete testing
Clause-7.1(General- Requirements)	-	12000	For complete testing
Clause-7.2, Table 3(C)	-	12000	For complete testing
Clause-7.2, Table 3(Si)	-	12000	For complete testing
Clause-7.2, Table 3(Mn)	-	12000	For complete testing
Clause-7.2, Table 3(P)	-	12000	For complete testing
Clause-7.2, Table 3(S)	-	12000	For complete testing
Clause-7.2, Table 3(Cr)	-	12000	For complete testing
Clause-7.2, Table 3(Mo)	-	12000	For complete testing
Clause-7.2, Table 3(Ni)	-	12000	For complete testing
Clause-7.2, Table 3(V)	-	12000	For complete testing
Clause-7.2, Table 3(W)	-	12000	For complete testing
Clause -7.2, Table-4(Al)	-	12000	For complete testing
Clause -7.2, Table-4(Cu)	-	12000	For complete testing
Clause-7.3(Hardenability)	-	12000	For complete testing
Clause-7.4(Hardness)	-	12000	For complete testing
Clause-7.5.1(Austenitic grain size of case-hardening and induction-hardening bearing steels)	-	12000	For complete testing
Clause-7.5.2(Spheroidization and distribution of carbides)	-	12000	For complete testing
Clause-7.6.1(Microscopic inclusions)	-	12000	For complete testing
Clause-7.6.2(Macroscopic inclusions)	-	12000	For complete testing
Clause-7.7(Internal soundness)	-	12000	For complete testing
Clause-7.8(Surface quality)	-	12000	For complete testing
Clause-7.9(Shape, dimensions and tolerances)	-	12000	For complete testing
Clause-8.2(Frequency of testing)	-	12000	For complete testing
Clause-8.3.1(Verification of the hardenability and hardness)	-	12000	For complete testing
Clause-8.3.2(Inspection of the surface quality)	-	12000	For complete testing
Clause-8.3.3(Dimensional and shape inspection)	-	12000	For complete testing
Clause-9.1(Chemical analysis)	-	12000	For complete testing
Clause-9.2(Hardness and hardenability tests)	-	12000	For complete testing
Clause-10(Marking)	-	12000	For complete testing
Clause-6.3.1(Heat-treatment condition)	-	-	-
Clause-6.3.2(Particular surface conditions)	-	-	-
Clause-6.3.3(Traceability of the cast)	-	-	-
Clause-7.1(General- Requirements)	-	-	-
Clause-7.2, Table 3(C)	-	-	-
Clause-7.2, Table 3(Si)	-	-	-
Clause-7.2, Table 3(Mn)	-	-	-
Clause-7.2, Table 3(P)	-	-	-
Clause-7.2, Table 3(S)	-	-	-
Clause-7.2, Table 3(Cr)	-	-	-
Clause-7.2, Table 3(Mo)	-	-	-
Clause-7.2, Table 3(Ni)	-	-	-
Clause-7.2, Table 3(V)	-	-	-
Clause-7.2, Table 3(W)	-	-	-
Clause -7.2, Table-4(Al)	-	-	-
Clause -7.2, Table-4(Cu)	-	-	-
Clause-7.3(Hardenability)	-	-	-
Clause-7.4(Hardness)	-	-	-
Clause-7.5.1(Austenitic grain size of case-hardening and induction-hardening bearing steels)	-	-	-
Clause-7.5.2(Spheroidization and distribution of carbides)	-	-	-
Clause-7.6.1(Microscopic inclusions)	-	-	-
Clause-7.6.2(Macroscopic inclusions)	-	-	-
Clause-7.7(Internal soundness)	-	-	-
Clause-7.8(Surface quality)	-	-	-
Clause-7.9(Shape, dimensions and tolerances)	-	-	-
Clause-8.2(Frequency of testing)	-	-	-
Clause-8.3.1(Verification of the hardenability and hardness)	-	-	-
Clause-8.3.2(Inspection of the surface quality)	-	-	-
Clause-8.3.3(Dimensional and shape inspection)	-	-	-
Clause-9.1(Chemical analysis)	-	-	-
Clause-9.2(Hardness and hardenability tests)	-	-	-
Clause-10(Marking)	-	-	-

-
Included w.e.f 16.12.2025

First
Prev
3
4
5
6
Next
Last

Bureau of Indian Standards

The National Standards Body of India

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List