BIS - LIMS (Laboratory Information Management System)

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List

Reset

282 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

271

IS 383 (2016)

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

Coarse And Fine Aggregate for concrete 10 mm to 80 mm,

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 (5.2.2, 5.2.1, 5.2.3, shale table-2 ) (Deleterious material (Clay lumps, coal & lignite, material finer than 75 micron IS sieve, Soft fragments,shale))	-	1500	-
5.3(Flakiness Index)	-	1250	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.2(a)( Aggregates Impact Value)	-	1250	-
5.4.2(b)( Aggregates Impact Value)	-	1250	-
5.4.3(a)( Aggregate Abrasion Value)	-	1000	-
5.4.3(b)( Aggregate Abrasion Value)	-	1000	-
5.5(Soundness By Magnesium Sulphate)	-	2000	-
5.7 table 3(WaterAbsorption)	-	750	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	250	-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	1250	-
5.2 (5.2.2, 5.2.1, 5.2.3, shale table-2 ) (Deleterious material (Clay lumps, coal & lignite, material finer than 75 micron IS sieve, Soft fragments,shale))	-	1500	-
5.3(Flakiness Index)	-	1250	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.2(a)( Aggregates Impact Value)	-	1250	-
5.4.2(b)( Aggregates Impact Value)	-	1250	-
5.4.3(a)( Aggregate Abrasion Value)	-	1000	-
5.4.3(b)( Aggregate Abrasion Value)	-	1000	-
5.5(Soundness By Magnesium Sulphate)	-	2000	-
5.7 table 3(WaterAbsorption)	-	750	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	250	-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	1250	-
5.7 table 4 (Calcium oxide)	-	500	-
6.1-Table 7(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Nominal Size of aggregate)	-	250	-
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	250	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	250	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	250	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	250	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	250	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	250	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	250	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	250	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	250	-
5.2 (5.2.2, 5.2.1, 5.2.3, shale table-2 ) (Deleterious material (Clay lumps, coal & lignite, material finer than 75 micron IS sieve, Soft fragments,shale))	-	1500	-
5.3(Flakiness Index)	-	1250	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.2(a)( Aggregates Impact Value)	-	1250	-
5.4.2(b)( Aggregates Impact Value)	-	1250	-
5.4.3(a)( Aggregate Abrasion Value)	-	1000	-
5.4.3(b)( Aggregate Abrasion Value)	-	1000	-
5.5(Soundness By Magnesium Sulphate)	-	2000	-
5.7 table 3(WaterAbsorption)	-	750	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	250	-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	1250	-
5.7 table 4 (Calcium oxide)	-	500	-
6.1-Table 7(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Nominal Size of aggregate)	-	250	-
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	250	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	250	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	250	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	250	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	250	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	250	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	250	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	250	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	250	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (coarse aggregate))	-	2000	For complete Alkali reaction and soundness of aggregate
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate))	-	2000	For complete Alkali reaction and soundness of aggregate
5.6(Alkali Agregate Reaction )	-	2000	For complete Alkali reaction and soundness of aggregate
Clause 5.6(Nature of Aggregate)	-	2000	For complete Alkali reaction and soundness of aggregate
Clause 5.6(Dissolved Silica)	-	2000	For complete Alkali reaction and soundness of aggregate
Clause 5.6(Reduction in Alkalinity)	-	2000	For complete Alkali reaction and soundness of aggregate

-
Included w.e.f. 21-09-2022.

272

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

15 to 150 mm

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Outer Diameter, Thickness & Mass)	-	250	-
Cl 8(Workmanship)	-	750	-
Cl 8(Workmanship)	-	750	-
Cl 9(Workmanship)	-	1000	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	2000	-
Cl 6(Outer Diameter, Thickness & Mass)	-	250	-
Cl 8(Workmanship)	-	1000	-
Cl 8(Workmanship)	-	1000	-
Cl 9(Workmanship)	-	1000	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	2000	-
Cl 6(Outer Diameter, Thickness & Mass)	-	250	-
Cl 8(Workmanship)	-	1000	-
Cl 8(Workmanship)	-	1000	-
Cl 9(Workmanship)	-	1000	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	2000	-
9(Straightness)	-	500	-
5 AND AS PER IS 10748(COPPER)	-	7500	For complete chemical test - if required
5 AND AS PER IS 10748(MICRO ALLOY)	-	7500	For complete chemical test - if required
5 AND AS PER IS 10748(CARBON EQUIVALENT)	-	7500	For complete chemical test - if required
5 AND AS PER IS 10748(CARBON)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3( ALUMINIUM)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(SILICON)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(NITROGEN)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(MANGANESE)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(PHOSPHURS)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(SULPHUR)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3( CARBON)	-	7500	For complete chemical test - if required
Cl 6(Outer Diameter, Thickness & Mass)	-	-	-
Cl 8(Workmanship)	-	-	-
Cl 8(Workmanship)	-	-	-
Cl 9(Workmanship)	-	-	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	-	-
9(Straightness)	-	-	-

-
Included w.e.f. 21-09-2022.

273

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

8DS20, 8DS21, 9DS20,9DS21,10DS20,10DS21,12DT20,12D21

12250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0(Straightness)	-	1000	-
Cl. 9(Length)	-	2500	-
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	2500	-
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	2500	-
13.1.3(Tensile Strength)	-	2500	-
13.6(Crush Test)	-	1500	-
13.2(Flattening Test)	-	1250	-
13.5(Drift Expansion Test)	-	1500	-
13.3(Bend Test (Strip))	-	1500	-
11.2(Surface Protection)	-	1500	-
4.1(Sulphur-Percentage by mass)	-	2000	-
4.1(Phosphorus-Percentage by mass)	-	2000	-

-
Included w.e.f. 21-09-2022.

274

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

CF & HF

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	4000	For complete dimensional test
Cl. 14.1(Weight on individual length)	-	500	-
Cl. 14.1(Weight on lots of 10 tonnes min)	-	500	-
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Plastic Modulus about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	4000	For complete Dimensional test
Cl. 14.1(Weight on individual length)	-	500	For weight test
Cl. 14.1(Weight on lots of 10 tonnes min)	-	500	For weight test
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about Y-Y))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus about X-X))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Plastic Modulus about Y-Y))	-	4000	For complete Dimension test
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	3500	For Mechanical Test
Cl. 15.2, Table 3(Yield Strength- IS 1608)	-	3500	For Mechanical Test
Cl. 15.2, Table 3(Elongation- IS 1608)	-	3500	For Mechanical Test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	4000	For complete Dimensional test
Cl. 14.1(Weight on individual length)	-	500	-
Cl. 14.1(Weight on lots of 10 tonnes min)	-	500	-
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Plastic Modulus about Y-Y))	-	4000	For complete Dimensional test
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	3500	For complete mechanical test
Cl. 15.2, Table 3(Yield Strength- IS 1608)	-	3500	For complete mechanical test
Cl. 15.2, Table 3(Elongation- IS 1608)	-	3500	For complete mechanical test

-
Included w.e.f. 21-09-2022.

275

IS 6649 (1985)

Specification for hardened and tempered washers for high strength structural bolts and nuts (First Revision)

M 16 to M 36/ Type A, Type B, Type C

16900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 Table-1(Dimensions Type A- d1)	-	5000	For complete dimension test
3 Table-1(Dimensions Type A- d2)	-	5000	For complete dimension test
3 Table-1(Dimensions Type A- S)	-	5000	For complete dimension test
3 Table-2(Dimensions Type B&C- d)	-	5000	For complete dimension test
3 Table-2(Dimensions Type B&C- a)	-	5000	For complete dimension test
3 Table-2(Dimensions Type B&C- t)	-	5000	For complete dimension test
3 Table-2(Dimensions Type B&C- θ)	-	5000	For complete dimension test
7(Hardness)	-	500	-
8.1(Freedom from defect)	-	3400	For Galvanization and qualitative test
8.1(Uniformity of zinc coating)	-	500	For Galvanization and qualitative test
8.1(Mass of zinc coating)	-	500	For Galvanization and qualitative test
8.1(Knife test (Adhesion of coating))	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- d1)	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- d2)	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- S)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- d)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- a)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- t)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- θ)	-	5000	For complete dimensional and qualitative tests
7(Hardness)	-	500	-
8.1(Freedom from defect)	-	500	-
8.1(Uniformity of zinc coating)	-	500	-
8.1(Mass of zinc coating)	-	500	-
8.1(Knife test (Adhesion of coating))	-	5000	For complete dimensional and qualitative tests
5(Chemical Composition- Sulphur)	-	3000	For complete chemical test
5(Chemical Composition- Phosphorus)	-	3000	For complete test
3 Table-1(Dimensions Type A- d1)	-	5000	For complete dimensional tests
3 Table-1(Dimensions Type A- d2)	-	5000	For complete dimensional tests
3 Table-1(Dimensions Type A- S)	-	5000	For complete dimensional tests
3 Table-2(Dimensions Type B&C- d)	-	5000	For complete dimensional tests
3 Table-2(Dimensions Type B&C- a)	-	5000	For complete dimensional tests
3 Table-2(Dimensions Type B&C- t)	-	5000	For complete dimensional tests
3 Table-2(Dimensions Type B&C- θ)	-	5000	For complete dimensional tests
7(Hardness)	-	500	-
8.1(Freedom from defect)	-	5000	For complete dimension and qualitative tests
8.1(Uniformity of zinc coating)	-	500	-
8.1(Mass of zinc coating)	-	500	-
8.1(Knife test (Adhesion of coating))	-	5000	For complete dimension and qualitative tests
5(Chemical Composition- Sulphur)	-	3000	For complete chemical test - if required
5(Chemical Composition- Phosphorus)	-	3000	For complete chemical test - if required
3 Table-1(Dimensions Type A- d1)	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- d2)	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- S)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- d)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- a)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- t)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- θ)	-	5000	For complete dimensional and qualitative tests
7(Hardness)	-	7000	For complete mechanical tests
8.1(Freedom from defect)	-	5000	For complete dimensional and qualitative tests
8.1(Uniformity of zinc coating)	-	500	-
8.1(Mass of zinc coating)	-	500	-
8.1(Knife test (Adhesion of coating))	-	5000	For complete dimensional and qualitative tests
5(Chemical Composition- Sulphur)	-	3000	For complete chemical tests - if required
5(Chemical Composition- Phosphorus)	-	3000	For complete chemical tests - if required

-
Included w.e.f. 21-09-2022.

276

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

Light Duty, Heavy Duty, Medium Duty, Extra Heavy Duty

14820 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 and Table 1(Dimensions of Frame - A)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - B)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - C)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - D)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - E)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - F)	-	10000	For complete dimensional tests
5.2(Dimensions of cover- Diameter)	-	10000	-
5.2(Clearance at top between the frame and the cover all round the periphery)	-	10000	-
5.2(Top surface ofthe frame and cover is in level)	-	10000	-
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	10000	-
5.2 and Fig 1(Clear cover to reinforcement)	-	10000	-
5.2 and Fig 1(Distance of housing from the edge)	-	10000	For complete dimensional tests
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests
7.4.1(Edge Protection and Finishing - Frame)	-	10000	-
7.4.2(Edge Protection and Finishing - Cover)	-	10000	-
7.4.2(Edge Protection and Finishing - Cover)	-	10000	-
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests
7.4.2(Edge Protection and Finishing - Cover)	-	10000	-
9.3 and Table and Annex C(Load Test)	-	8500	-
5.2 and Table 1(Dimensions of Frame - A)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - B)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - C)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - D)	-	10000	-
5.2 and Table 1(Dimensions of Frame - E)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - F)	-	10000	For complete dimensional tests
5.2(Dimensions of cover- Diameter)	-	10000	For complete dimensional tests and finish
5.2(Clearance at top between the frame and the cover all round the periphery)	-	10000	For complete dimensional tests
5.2(Top surface ofthe frame and cover is in level)	-	10000	For complete dimensional tests
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	10000	For complete dimensional tests
5.2 and Fig 1(Clear cover to reinforcement)	-	10000	For complete dimensional tests and finish
5.2 and Fig 1(Distance of housing from the edge)	-	10000	For complete dimensional tests
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	-
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
9.3 and Table and Annex C(Load Test)	-	8500	-
8(LIFTING HOOKS)	-	10000	For complete dimensional tests and finish
8(LIFTING HOOKS)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - A)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - B)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - C)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - D)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - E)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - F)	-	10000	For complete dimensional tests and finish
5.2(Dimensions of cover- Diameter)	-	10000	For complete dimensional tests and finish
5.2(Clearance at top between the frame and the cover all round the periphery)	-	10000	For complete dimensional tests and finish
5.2(Top surface ofthe frame and cover is in level)	-	10000	For complete dimensional tests and finish
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	10000	For complete dimensional tests and finish
5.2 and Fig 1(Clear cover to reinforcement)	-	10000	For complete dimensional tests and finish
5.2 and Fig 1(Distance of housing from the edge)	-	10000	For complete dimensional tests and finish
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests and finish
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
9.3 and Table and Annex C(Load Test)	-	8500	-
8(LIFTING HOOKS)	-	10000	For complete dimensional tests and finish
8(LIFTING HOOKS)	-	10000	For complete dimensional tests and finish

-
Included w.e.f. 21-09-2022.

277

IS 13095 (2020)

Butterfly Valves for General Purposes ( First Revision )

50 mm to 650 mm

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0( NOMINAL SIZES )	-	2500	For dimensional and qualitative Tests
7.0(NOMINAL PRESSURES)	-	5000	For complete hydrostatic test
9.1.1 ( Double Flanged Body Ends)	-	2500	For dimensional and qualitative Tests
9.2.2(Wafer Body Ends)	-	2500	For dimensional and qualitative Tests
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-	2500	For dimensional and qualitative Tests
11.0(Bodies)	-	2500	For dimensional and qualitative Tests
12.0(DISC AND SHAFT)	-	2500	For dimensional and qualitative Tests
14.0(BEARINGS)	-	2500	For dimensional and qualitative Tests
14.2(BEARINGS)	-	2500	For dimensional and qualitative Tests
14.3(BEARINGS)	-	2500	For dimensional and qualitative Tests
17.2(Body Test)	-	5000	For complete Hydrostatic Tests
17.4(Disc Strength Test)	-	5000	For complete Hydrostatic Tests
17.3(Seat Test)	-	5000	For complete Hydrostatic Tests
Cl. 15 Table 2(Materials)	-	7500	For each component (CI, Stainless Steel) - If required
6.0( NOMINAL SIZES )	-	2500	For dimensional and qualitative Tests
7.0(NOMINAL PRESSURES)	-	5000	For complete hydrostatic test
9.1.1 ( Double Flanged Body Ends)	-	2500	For dimensional and qualitative Tests
9.2.2(Wafer Body Ends)	-	2500	For dimensional and qualitative Tests
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-	2500	For dimensional and qualitative Tests
11.0(Bodies)	-	2500	For dimensional and qualitative Tests
12.0(DISC AND SHAFT)	-	2500	For dimensional and qualitative Tests
14.0(BEARINGS)	-	2500	For dimensional and qualitative Tests
14.2(BEARINGS)	-	2500	For dimensional and qualitative Tests
14.3(BEARINGS)	-	2500	For dimensional and qualitative Tests
17.2(Body Test)	-	5000	For complete Hydrostatic Tests
17.4(Disc Strength Test)	-	5000	For complete Hydrostatic Tests
17.3(Seat Test)	-	5000	For complete Hydrostatic Tests
Cl. 15 Table 2(Materials)	-	7500	For each component (CI, Stainless Steel) - If required
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-d4)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-f)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Bolting )	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -Nos. )	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -d2)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck -d3)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck- r)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-D)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-b)	-	2000	--
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-d4)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-f)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Bolting)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -Nos. )	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -d2 )	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -k)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck -d3)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck-r)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Pipe O.D.- d1)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - D)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - b)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - d4)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Bolting)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling - Nos.)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -d2)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -k)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange -D)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange - b)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - d4)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - f)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Bolting)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling - Nos.)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -d2)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -k)	-	2000	-

-
-

278

IS 14329 (1995)

Malleable iron castings - Specification

WM350 and WM400,BM300, BM320 and BM350, PM 450 to PM700

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.2.1, 10.1, Table 1(Nominal diameter)	-	250	-
9.2.1, 10.1, Table 1(Tolerances on nominal diameter)	-	2000	-
9.2.1, 10.1, Table 1(Shank Dimensions, Diameter)	-	2000	-
9.2.1, 10.1, Table 1(Shank Dimensions, Length)	-	2000	-
9.2.1, 10.1, Table 1(Gauge length)	-	2000	-
9.2.1, 10.1, Table 1(Length)	-	2000	-
9.2.1, 10.1, Table 1(Radius at shoulder)	-	2000	-
10.1(Tensile Test)	-	2000	-
10.2(Hardness Test)	-	500	-
8.0(FREEDOM FROM DEFECTS)	-	500	For complete hardness and qualitative tests

-
Included w.e.f. 21-09-2022.

279

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

Water for Construction Purpose,Compressive strength fo

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.1(Average Compressive Strength)	-	2500	-
16.1(Average Compressive Strength)	-	2500	-
Cl 5.4 .2(pH)	-	300	-
Cl 5.4 Table 1 (iii)(Sulphate)	-	300	-
Cl 5.4 Table 1 (ii)(Inorganic Solids)	-	300	-
Cl 5.4 Table 1 (i)(Organic Solids)	-	300	-
Cl 5.4 Table 1 (v)(Suspended Matter)	-	300	-
5.4-(b)-IS: 3025 (P-23)(Volume of 0.02 N H2SO4 to neutralized 100 ml of water using mixed indicator)	-	1100	-
5.4-(a)-IS: 3025 (P-22)(Volume of 0.02 N NaOH to neutralized 100 ml of water using phenolphthalein indicator)	-	1100	-
16.1(Average Compressive Strength)	-	2500	-
Cl 5.4 .2(pH)	-	300	-
Cl 5.4 Table 1 (iii)(Sulphate)	-	300	-
Cl 5.4 Table 1 (ii)(Inorganic Solids)	-	300	-
Cl 5.4 Table 1 (i)(Organic Solids)	-	300	-
Cl 5.4 Table 1 (v)(Suspended Matter)	-	300	-
5.4-(b)-IS: 3025 (P-23)(Volume of 0.02 N H2SO4 to neutralized 100 ml of water using mixed indicator)	-	1100	-
5.4-(a)-IS: 3025 (P-22)(Volume of 0.02 N NaOH to neutralized 100 ml of water using phenolphthalein indicator)	-	1100	-
Cl 5.4 Table 1 (iv)(Chloride)	-	300	-

-
Included w.e.f. 21-09-2022.

280

IS 410 (1977)

Specification for cold rolled brass sheet, strip and foil (Third Revision)

Annealed, Quarter Hard, Half Hard, Hard, Extra Hard, Sp

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.1(Tensile Test)	-	2000	For tensile and elongation test
Table-2(Vickers Hardness)	-	500	-
6.1 Table-1(Cu)	-	2000	-
Table-2(Thickness)	-	750	-
6.1 Table-1(Pb)	-	2000	-
6.1 Table-1(Fe)	-	2000	-
6.1 Table-1(Total impurities including iron)	-	2000	-
6.1 Table-1(Zn)	-	2000	-
4.0(Freedom from defects)	-	2000	-
Table-2(Elongation)	-	2000	For tensile and elongation test

-
Included w.e.f. 21-09-2022.

281

IS 16176 (2014)

Ratchet pipe threader for taper pipe threads (R - Series) - Specification

.½” to 6”

13700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions)	-	9000	For complete dimensional and qualitative tests.
6.2(Hardness)	-	700	-
9.1(Performance of thread testing)	-	4000	For complete thread parameters testing
4(Dimensions)	-	9000	For complete dimensional and qualitative tests.
6.2(Hardness)	-	700	For Hardness Test
9.1(Performance of thread testing)	-	4000	For complete thread parameters testing
7(Workmanship & Finish)	-	9000	For complete dimensional and qualitative tests.
5(Materials)	-	3500	For complete chemical tests (if required)
9.4(Measurement of gauging of threads)	-	4000	For complete gauging parameters test
9.3(Measurement of length of external thread)	-	4000	For complete gauging parameters test
9.2(Cutting of threads on a pipe testing)	-	4000	For complete gauging parameters test
6.3(To check the functioning of ratchet handle by rotating the locking pin 180°.)	-	9000	For complete dimensional and qualitative tests.
6.1(Manufacturing Quality (Visual))	-	9000	For complete dimensional and qualitative tests.
4(Dimensions)	-	-	-
6.2(Hardness)	-	-	-
9.1(Performance of thread testing)	-	-	-
7(Workmanship & Finish)	-	-	-
5(Materials)	-	-	-
9.4(Measurement of gauging of threads)	-	-	-
9.3(Measurement of length of external thread)	-	-	-
9.2(Cutting of threads on a pipe testing)	-	-	-
6.3(To check the functioning of ratchet handle by rotating the locking pin 180°.)	-	-	-
6.1(Manufacturing Quality (Visual))	-	-	-

-
Included w.e.f. 21-09-2022.

282

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

Annealed (Soft)(O),Half Hard(HB) and Hard (HD),GR 1,GR2

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Dimension and Tolerances)	-	2500	For complete dimension and qualitative tests.
9.1 Table-2(Tensile Strength)	-	2500	-
9.2(Vickers Hardness)	-	2500	-
8.1 Table 1(Cu)	-	3000	For complete chemical tests
8.1 Table 1(Pb)	-	3000	For complete chemical tests
8.1 Table 1(Fe)	-	3000	-
8.1 Table 1(Total other impurities excluding iron)	-	3000	For complete chemical tests
8.1 Table 1(Zn)	-	3000	For complete chemical tests
10.1(Mercurous Nitrate Test)	-	3000	For complete chemical tests
5.0(Freedom from defects)	-	2500	For complete dimension and qualitative tests.

-
Included w.e.f. 21-09-2022.

Bureau of Indian Standards

The National Standards Body of India

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List