BIS - LIMS (Laboratory Information Management System)

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List

Reset

322 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

301

IS 2202 : Part 1 (1999)

Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1( Squareness Test - IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.1(Variation in thickness - IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.1(Thickness - IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.1(Width- IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.1(Height - IS 4020 (Pt-2))	-	5000	For Cl 11.1
11.2( Twist, cupping & wrapping - IS 4020 (Pt-3))	-	1000	For Cl 11.2
11.3(Depth of deviation - IS 4020(Pt-4))	-	1000	For Cl 11.3
11.4(Depth of indentation - IS 4020(Pt-5))	-	1000	For Cl 11.4
11.4(Impact Indentation Test - IS 4020(Pt-5))	-	1000	For Cl 11.4
11.5(Residual deflection - IS 4020(Pt-6))	-	2000	For Cl 11.5
11.5(Deflection at maximum load - IS 4020(Pt-6))	-	2000	For Cl 11.5
11.6(Residual lateral buckling - IS 4020(Pt-7))	-	2000	For Cl 11.6
11.6(Lateral buckling during loading - IS 4020(Pt-7))	-	2000	For Cl 11.6
11.6(Residual deflection after removal of load - IS 4020(Pt-7))	-	2000	For Cl 11.6
11.6(Deflection of the edge at maximum load - IS 4020(Pt-7))	-	2000	For Cl 11.6
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	2000	For Cl 11.7
11.7(Shock Resistance Test -IS 4020(Pt-8))	-	2000	For Cl 11.7
11.8(Residual deformation after 15 minutes of unloading - IS 4020(Pt-9))	-	2000	For Cl 11.8
11.8(Initial deflection - IS 4020(Pt-9))	-	2000	For Cl 11.8
11.8(Buckling Test - IS 4020(Pt-9))	-	2000	For Cl 11.8
11.9(Slamming Test - IS 4020(Pt-10))	-	750	For Cl 11.9
11.1(Misuse Test - IS 4020(Pt-11))	-	750	For Cl 11.10
11.11(The recovery of the original size after subjecting the door to high and low humidity- IS 4020(Pt-12))	-	9750	For Cl 11.11
11.11(Maximum departure from the general planeness - IS 4020(Pt-12))	-	9750	For Cl 11.11
11.11(Varying Humidity Test - IS 4020(Pt-12))	-	9750	For Cl 11.11
11.12(End Immersion Test - IS 4020(Pt-13))	-	1000	For Cl 11.12
11.13(Knife Test - IS 4020(Pt-14))	-	500	For Cl 11.13
11.14(Glue Adhesion Test - IS 4020(Pt-15))	-	750	For Cl 11.14
11.15(Screw Withdrawal Strength - IS 4020 (Pt-16))	-	750	For Cl 11.15
11.15(Screw Withdrawal Resistance test - IS 4020 (Pt-16))	-	750	For Cl 11.15
6.2(Plywood)	-	250	For complete Cl 9
9.2(Workmanship & finish - IS 2202(Pt-1))	-	250	For complete Cl 9
9.3(Workmanship & finish - IS 2202(Pt-1))	-	250	For complete Cl 9

-
-

302

IS 1879 (2010)

Malleable cast iron pipe fittings - Specification (Third Revision)

Except 1/8", 1/4" and 8"

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 - Table 4 to Table 27(a - IS 1879)	-	2500	For complete Cl 5 and Cl 7
7.1 - Table 4 to Table 27(b - IS 1879)	-	2500	For complete Cl 5 and Cl 7
7.1 - Table 4 to Table 27(c- IS 1879)	-	2500	For complete Cl 5 and Cl 7
7.1 - Table 4 to Table 27(d- IS 1879)	-	2500	For complete Cl 5 and Cl 7
7.1 - Table 28(d -IS 1879)	-	2500	For complete Cl 5 and Cl 7
7.1 - Table 28(D - IS 1879)	-	2500	For complete Cl 5 and Cl 7
7.2- Table 2(Wall thickness of fittings - IS 1879)	-	2500	For complete Cl 5 and Cl 7
8.1(Thread -IS 554)	-	750	For complete Cl 8
8.2(Alignment of threads -IS 554)	-	750	For complete cl 8
11(Pressure Test)	-	2000	For Complete Cl 11
12(Compression Test)	-	2000	For complete Cl 12
10.i)(Mass of Galvanized coating)	-	250	For complete cl 10
10.ii)(Uniformity of Galvanized coating-IS 2633)	-	250	For complete cl 10
6.1(Tensile Strength - IS 14329)	-	1500	For tensile and elongation
6.1(Elongation - Is 14329)	-	1500	For tensile and elongation
5.1.1(Type of Fittings - IS 1879)	-	2500	For complete Cl 5 and Cl 7
5.1.2(Size designation - IS 1879)	-	2500	For complete Cl 5 and Cl 7
5.1.2.1(Equal fitting - IS 1879)	-	2500	For complete Cl 5 and Cl 7
5.1.2.2(Unequal fitting -IS 1879)	-	2500	For complete Cl 5 and Cl 7
7.5 - Table 2(Projection of Rainforcement - IS 1879)	-	2500	For complete Cl 5 and Cl 7
7.5 - Table 3(Width of Rainforcement - IS 1879)	-	2500	For complete Cl 5 and Cl 7

-
-

303

IS 1363 : Part 1 (2019)

Hexagon Head Bolts, Screws and Nuts of Product Grade ‘C’ Part 1 Hexagon Head Bolts ( Size Range M 5 to M 64 ) ( Fifth Revision )

For M8, M10,M12,M16,M20,M24,M30,M36,M39 only

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3-Table 1(Dimensions-d)	-	5000	For complete Cl 3
3-Table 1(Dimensions-p)	-	5000	For complete Cl 3
3-Table 1(Dimensions-b)	-	5000	For complete Cl 3
3-Table 1(Dimensions-c(Maximum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-da(Maximum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-ds(Minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-ds(maximum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-dw(minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-e(minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-k(nominal))	-	5000	For complete Cl 3
3-Table 1(Dimensions-k(Minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-k(maximum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-kw(minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-r(minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-s(minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-s(maximum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-l(nominal))	-	5000	For complete Cl 3
3-Table 1(Dimensions-l(minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-l(maximum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-ls(minimum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-lg(maximum))	-	5000	For complete Cl 3
3-Table 1(Dimensions-β)	-	5000	For complete Cl 3
3-Table 1(Dimensions-u)	-	5000	For complete Cl 3
3-Table 2(Dimensions-d)	-	5000	For complete Cl 3
3-Table 2(Dimensions-p)	-	5000	For complete Cl 3
3-Table 2(Dimensions-b)	-	5000	For complete Cl 3
3-Table 2(Dimensions-c(Maximum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-da(Maximum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-ds(Minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-dw(minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-e(minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-k(nominal))	-	5000	For complete Cl 3
3-Table 2(Dimensions-k(Minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-kw(minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-r(minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-s(minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-s(maximum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-l(nominal))	-	5000	For complete Cl 3
3-Table 2(Dimensions-l(minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-l(maximum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-ls(minimum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-lg(maximum))	-	5000	For complete Cl 3
3-Table 2(Dimensions-β)	-	5000	For complete Cl 3
3-Table 2(Dimensions-u)	-	5000	For complete Cl 3
4-Table 3(General requirements-ISO 8992)	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Threads-ISO 724 & 965(1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Property class (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Tensile strength (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Lower yield strength (ISO 898-1) )	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress at 0,2 % non-proportional elongation (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress at 0,0048d non-proportional elongation for full-size fasteners (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Stress under proof load (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Proof strength ratio (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Percentage elongation after fracture for machined test pieces (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Percentage reduction of area after fracture for machined test pieces (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Elongation after fracture for full-size fasteners (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Head soundness (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Vickers hardness (ISO 898-1))	-	500	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Brinell hardness (ISO 898-1))	-	500	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1))	-	500	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1))	-	500	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Surface hardness (ISO 898-1))	-	500	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Non-carburization (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Height of non-decarburized thread zone (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Depth of complete decarburization in the thread (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Reduction of hardness after retempering (ISO 898-1))	-	500	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Breaking torque (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Impact strength (ISO 898-1))	-	6000	Cl 4 Mechanical properties of metal
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Quench Cracks(ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging cracks (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screw (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Circular head screws (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Circular head screws (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Raw material seams and laps (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Voids (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Folds (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Tool marks (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-- Quench cracks (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks - (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Width (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Depth (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Raw material, seams and laps- (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Voids- (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Folds- (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Tool marks - (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	3000	For Surface Integrity
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Damages - (ISO 6157-3))	-	3000	For Surface Integrity

-
-

304

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Nominal dia upto 10 mm

5850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5 & 6(Diameter)	-	2350	For Complete Cl 6 and Cl 7
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	1500	For Complete Cl 8
Cl 7(UTM)	-	1000	For Complete Cl 1000
Clause 3.1.1(Sulphur)	-	1000	For Complete Chemical testing
Clause 3.1.1(Phosphorus)	-	1000	For Complete Chemical testing
Cl 4.1(Workmanship)	-	2350	For Complete C4
Cl. 7.1(Elongation)	-	1000	For Complete Cl 7
Cl. 7.1(Proof Stress 0.2 %)	-	1000	For Complete Cl 7
Cl. 6.2(Length)	-	2350	For Complete Cl 6 and 7
Clause 3(Nitrogen)	-	1000	For Complete Chemical testing, if required
Clause 3(Nitrogen)	-	1000	For Complete Chemical testing, if required
Clause 8.3(Reverse Bend test)	-	1500	For Complete Cl 8

-
Up to 7.50 mm size only

305

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

Grade I & Grade II

3150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6.2(Diameter & Ovality)	-	1500	For complete cl 6
Cl 6.2(Weight)	-	1500	For complete cl 6
Cl 8.2(Bend test)	-	500	For complete cl 8
Cl 9.3(Press)	-	500	For complete cl 9
Cl 9.3(Press)	-	500	For complete cl 9
Cl 5.1(Workmanship)	-	500	For complete cl 5
Clause -4, 4.3(TITANIUM)	-	1000	For Complete Chemical testing, if required
Clause -4, 4.2(VANADIUM)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(NIOBIUM)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(Molybdenum)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(Chromium)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(Nickel)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1( ALUMINIUM)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(SILICON)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(NITROGEN)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(MANGANESE)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(PHOSPHURS)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1(SULPHUR)	-	650	For Complete Chemical testing, if required
Clause -4, 4.1( CARBON)	-	650	For Complete Chemical testing, if required
Clause 8.1(Elongation)	-	650	For Complete Cl 8
Clause 8.1(Yield Stress)	-	1000	For Complete Cl 8
Clause 6.1(Size)	-	1000	For Complete Cl 6
Clause 8.1(Ultimate Tensile Stress)	-	1000	For Complete Cl 8
Clause 4(By Calculation)	-	1000	-
Clause 4(By Calculation)	-	1000	-
Clause 4(Copper)	-	1000	For Complete Chemical testing, if required

-
-

306

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table-1(Sizes Diameter of Line wire)	-	750	For Complete Dimensional and Tolerances
5 Table-1(Sizes Diamater of Point wire)	-	750	For Complete Dimensional and Tolerances
5 Table-1(Sizes Mass of Completed barbed wire)	-	750	For Complete Dimensional and Tolerances
5 Table-1(Sizes Distance between two barbs)	-	750	For Complete Dimensional and Tolerances
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	750	For Complete Dimensional and Tolerances
12.1(Tensile Strength)	-	1500	For Complete Tensile Test
12.3(Ductility)	-	1000	For Complete Ductility Test
12.2(Uniformity of zinc coating)	-	350	For Complete Cl 12
7.2(Manufacture)	-	750	For Complete Dimensional and Tolerances
7.3(Manufacture)	-	750	For Complete Dimensional and Tolerances
9.1(Freedom from defects)	-	750	For Complete Cl 9
9.2(Freedom from defects)	-	750	For Complete Cl 9
12.1(Breaking load)	-	1500	For Complete Cl 12
12.2.1(Mass of zinc coating (line wire))	-	1500	For Complete Cl 12
12.2.2(Mass of zinc coating (point wire))	-	1500	For Complete Cl 12
Cl. 7.2(Cut Angle)	-	750	For Complete Cl 7
Cl. 7.2(Length of Barbs)	-	750	For Complete Cl 7
Cl. 7.2(Finishing of Barbs)	-	750	For Complete Cl 7
Cl. 7.1(General)	-	750	For Complete Cl 7
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	750	For complete Chemical Testing, if required
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	750	For complete Chemical Testing, if required
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	750	For complete Chemical Testing, if required
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	750	For complete Chemical Testing, if required
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	750	For complete Chemical Testing, if required

-
-

307

IS 9758 (1981)

Specification for flush valves and fittings for water closets and urinals

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 5(Manufacture & Construction)	-	2000	-
cl 6.1 to 6.3(Performance requirements)	-	10000	-
cl 7.1(Hydraulic pressure test)	-	3000	-
cl 7.2(Endurance test)	-	10000	-
cl 8(Finish)	-	500	-

-
Included w.e.f. 06-07-2023.

308

IS 14845 (2000)

Resilient seated cast iron air relief valves for water works purposes - specification

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 3)&(Cl5)(Type & Nom Size)	-	2500	For cl 3, 4, 5 ,8, 11
(Cl 3)&(Cl5)(Type & Nom Size)	-	2500	For cl 3, 4, 5 ,8, 11
(Cl 3)&(Cl5)(Type & Nom Size)	-	2500	For cl 3, 4, 5 ,8, 11
(Cl 4)(Nom.Pressures)	-	2500	For cl 3, 4, 5 ,8, 11
(Cl 8)(End Connection)	-	2500	For cl 3, 4, 5 ,8, 11
(Cl 8)(End Connection)	-	2500	For cl 3, 4, 5 ,8, 11
(Cl 8)(End Connection)	-	2500	For cl 3, 4, 5 ,8, 11
(Cl 9)(Material)	-	5000	Additonal (if required)
(Cl10.1)( Design And Manufacture)	-	2500	For cl 3, 4, 5 ,8, 11
(Cl10.2)( Body)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.2)( Body)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.2)( Body)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.2)( Body)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.2)( Body)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.2)( Body)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.3)( Covers of Large Orifice Chamber)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.4)(High Pressure Orifice)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.4)(High Pressure Orifice)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.4)(High Pressure Orifice)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.4)(High Pressure Orifice)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.5, Table 3)(Float)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.5, Table 3)(Float)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.5, Table 3)(Float)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.5, Table 3)(Float)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.5, Table 3)(Float)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.5, Table 3)(Float)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.5, Table 3)(Float)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.6)(Low Pressure Seat Ring)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.6)(Low Pressure Seat Ring)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.6)(Low Pressure Seat Ring)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.6)(Low Pressure Seat Ring)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl10.6)(Low Pressure Seat Ring)	-	5000	For complete cl 10.2, Cl 10.3, Cl 10.5 & Cl 10.6
(Cl 10.7)(Joint Supporting Ring)	-	5000	-
(Cl 10.8)(Cowl)	-	5000	-
(Cl 10.8)(Cowl)	-	5000	-
(Cl 10.9)(Gasket or jointing material )	-	5000	-
(Cl10.6)(Nut & Bolts)	-	15000	additional, If required
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
Cl 10.11(Built- in-isolating Valve)	-	5000	-
(Cl.11)(Finish)	-	1000	-
(Cl.12)(Testing and Performance)	-	7500	-
(Cl.12)(Testing and Performance)	-	7500	-
(Cl.12)(Testing and Performance)	-	7500	-
(Cl.12.4.4) : (Body Test )	-	5000	-
(Cl.14)(Coating)	-	2500	-
(Cl.14)(Coating)	-	2500	-

-
Included w.e.f. 06-07-2023.

309

IS 5820 (1970)

Specification for precast concrete cable covers

LV,HV,HVP,EHV

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-Table 1(Dimensions-Class)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-Type no.)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-Shape)	-	5000	For complete dimension and qualitative tests.
4-Table 1(Dimensions-L)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-W)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-T)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-T')	-	5000	For complete dimension and qualitative tests
8.2(mpact Strength)	-	5000	For complete dimension and qualitative tests
2.2.1(Size of aggregates)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-Class)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-Type no.)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-Shape)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-L)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-W)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-T)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-T')	-	5000	For complete dimension and qualitative tests
8.2(mpact Strength)	-	5000	For complete dimension and qualitative tests
2.2.1(Size of aggregates)	-	5000	For complete dimension and qualitative tests
6(FINISH)	-	5000	For complete dimension and qualitative tests
6(FINISH)	-	5000	For complete dimension and qualitative tests.
4-Table 1(Dimensions-Class)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-Type no.)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-Shape)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-L)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-W)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-T)	-	5000	For complete dimension and qualitative tests
4-Table 1(Dimensions-T')	-	5000	For complete dimension and qualitative tests
8.2(mpact Strength)	-	5000	For complete dimension and qualitative tests
2.2.1(Size of aggregates)	-	5000	For complete dimension and qualitative tests
6(FINISH)	-	5000	For complete dimension and qualitative tests
6(FINISH)	-	5000	For complete dimension and qualitative tests

-
Included w.e.f. 21-09-2022.

310

IS 1264 (1997)

Brass gravity die castings - Specification (Fourth Revision)

Grade DCB1 & DCB2

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Cu)	-	4000	-
7.0(Sn)	-	4000	-
7.0(Pb)	-	4000	-
7.0(Ni)	-	4000	-
7.0(Fe)	-	4000	-
7.0(Al)	-	4000	-
7.0(Mn)	-	4000	-
7.0(Si)	-	4000	-
7.0(Total impurities excluding Ni Pb Al Zn)	-	4000	-
5.0(Freedom from defects)	-	4000	Including Chemical and dimension (if required)

-
Included w.e.f. 21-09-2022.

311

IS 383 (2016)

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

Coarse And Fine Aggregate for concrete 10 mm to 80 mm,

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 (5.2.2, 5.2.1, 5.2.3, shale table-2 ) (Deleterious material (Clay lumps, coal & lignite, material finer than 75 micron IS sieve, Soft fragments,shale))	-	1500	-
5.3(Flakiness Index)	-	1250	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.2(a)( Aggregates Impact Value)	-	1250	-
5.4.2(b)( Aggregates Impact Value)	-	1250	-
5.4.3(a)( Aggregate Abrasion Value)	-	1000	-
5.4.3(b)( Aggregate Abrasion Value)	-	1000	-
5.5(Soundness By Magnesium Sulphate)	-	2000	-
5.7 table 3(WaterAbsorption)	-	750	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	250	-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	1250	-
5.2 (5.2.2, 5.2.1, 5.2.3, shale table-2 ) (Deleterious material (Clay lumps, coal & lignite, material finer than 75 micron IS sieve, Soft fragments,shale))	-	1500	-
5.3(Flakiness Index)	-	1250	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.2(a)( Aggregates Impact Value)	-	1250	-
5.4.2(b)( Aggregates Impact Value)	-	1250	-
5.4.3(a)( Aggregate Abrasion Value)	-	1000	-
5.4.3(b)( Aggregate Abrasion Value)	-	1000	-
5.5(Soundness By Magnesium Sulphate)	-	2000	-
5.7 table 3(WaterAbsorption)	-	750	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	250	-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	1250	-
5.7 table 4 (Calcium oxide)	-	500	-
6.1-Table 7(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Nominal Size of aggregate)	-	250	-
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	250	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	250	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	250	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	250	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	250	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	250	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	250	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	250	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	250	-
5.2 (5.2.2, 5.2.1, 5.2.3, shale table-2 ) (Deleterious material (Clay lumps, coal & lignite, material finer than 75 micron IS sieve, Soft fragments,shale))	-	1500	-
5.3(Flakiness Index)	-	1250	-
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1500	-
5.4.2(a)( Aggregates Impact Value)	-	1250	-
5.4.2(b)( Aggregates Impact Value)	-	1250	-
5.4.3(a)( Aggregate Abrasion Value)	-	1000	-
5.4.3(b)( Aggregate Abrasion Value)	-	1000	-
5.5(Soundness By Magnesium Sulphate)	-	2000	-
5.7 table 3(WaterAbsorption)	-	750	-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	250	-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	1250	-
5.7 table 4 (Calcium oxide)	-	500	-
6.1-Table 7(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Nominal Size of aggregate)	-	250	-
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	250	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	250	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	250	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	250	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	250	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	250	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	250	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	250	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	250	-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (coarse aggregate))	-	2000	For complete Alkali reaction and soundness of aggregate
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate))	-	2000	For complete Alkali reaction and soundness of aggregate
5.6(Alkali Agregate Reaction )	-	2000	For complete Alkali reaction and soundness of aggregate
Clause 5.6(Nature of Aggregate)	-	2000	For complete Alkali reaction and soundness of aggregate
Clause 5.6(Dissolved Silica)	-	2000	For complete Alkali reaction and soundness of aggregate
Clause 5.6(Reduction in Alkalinity)	-	2000	For complete Alkali reaction and soundness of aggregate

-
Included w.e.f. 21-09-2022.

312

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

15 to 150 mm

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Outer Diameter, Thickness & Mass)	-	250	-
Cl 8(Workmanship)	-	750	-
Cl 8(Workmanship)	-	750	-
Cl 9(Workmanship)	-	1000	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	2000	-
Cl 6(Outer Diameter, Thickness & Mass)	-	250	-
Cl 8(Workmanship)	-	1000	-
Cl 8(Workmanship)	-	1000	-
Cl 9(Workmanship)	-	1000	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	2000	-
Cl 6(Outer Diameter, Thickness & Mass)	-	250	-
Cl 8(Workmanship)	-	1000	-
Cl 8(Workmanship)	-	1000	-
Cl 9(Workmanship)	-	1000	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	2000	-
9(Straightness)	-	500	-
5 AND AS PER IS 10748(COPPER)	-	7500	For complete chemical test - if required
5 AND AS PER IS 10748(MICRO ALLOY)	-	7500	For complete chemical test - if required
5 AND AS PER IS 10748(CARBON EQUIVALENT)	-	7500	For complete chemical test - if required
5 AND AS PER IS 10748(CARBON)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3( ALUMINIUM)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(SILICON)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(NITROGEN)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(MANGANESE)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(PHOSPHURS)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3(SULPHUR)	-	7500	For complete chemical test - if required
Clause - 5.1, Table-3( CARBON)	-	7500	For complete chemical test - if required
Cl 6(Outer Diameter, Thickness & Mass)	-	-	-
Cl 8(Workmanship)	-	-	-
Cl 8(Workmanship)	-	-	-
Cl 9(Workmanship)	-	-	-
Cl 11(Tensile Test, Flattening Test & Cold Bend Test)	-	-	-
9(Straightness)	-	-	-

-
Included w.e.f. 21-09-2022.

313

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

8DS20, 8DS21, 9DS20,9DS21,10DS20,10DS21,12DT20,12D21

12250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0(Straightness)	-	1000	-
Cl. 9(Length)	-	2500	-
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	2500	-
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	2500	-
13.1.3(Tensile Strength)	-	2500	-
13.6(Crush Test)	-	1500	-
13.2(Flattening Test)	-	1250	-
13.5(Drift Expansion Test)	-	1500	-
13.3(Bend Test (Strip))	-	1500	-
11.2(Surface Protection)	-	1500	-
4.1(Sulphur-Percentage by mass)	-	2000	-
4.1(Phosphorus-Percentage by mass)	-	2000	-

-
Included w.e.f. 21-09-2022.

314

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

CF & HF

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	4000	For complete dimensional test
Cl. 14.1(Weight on individual length)	-	500	-
Cl. 14.1(Weight on lots of 10 tonnes min)	-	500	-
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete chemical test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Plastic Modulus about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	4000	For complete Dimensional test
Cl. 14.1(Weight on individual length)	-	500	For weight test
Cl. 14.1(Weight on lots of 10 tonnes min)	-	500	For weight test
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	-
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about Y-Y))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus about X-X))	-	4000	For complete Dimension test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Plastic Modulus about Y-Y))	-	4000	For complete Dimension test
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	3500	For Mechanical Test
Cl. 15.2, Table 3(Yield Strength- IS 1608)	-	3500	For Mechanical Test
Cl. 15.2, Table 3(Elongation- IS 1608)	-	3500	For Mechanical Test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Depth))	-	4000	For complete Dimensional test
Cl. 14.1(Weight on individual length)	-	500	-
Cl. 14.1(Weight on lots of 10 tonnes min)	-	500	-
Cl.7.1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.7.1(Carbon Equivalent-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	3500	For complete Chemical test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Width))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Thickness))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Weigth))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Area of Section))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Moment of Inertia about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Elastic Modulus))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Radius of Gyration about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Radius of Gyration about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Elastic Modulus about Y-Y))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections (Plastic Modulus about X-X))	-	4000	For complete Dimensional test
Cl.9.1, Table 1(Dimensions and Properties of Hollow Sections(Plastic Modulus about Y-Y))	-	4000	For complete Dimensional test
Cl. 15.2, Table 3(Tensile Strength- IS 1608)	-	3500	For complete mechanical test
Cl. 15.2, Table 3(Yield Strength- IS 1608)	-	3500	For complete mechanical test
Cl. 15.2, Table 3(Elongation- IS 1608)	-	3500	For complete mechanical test

-
Included w.e.f. 21-09-2022.

315

IS 6649 (1985)

Specification for hardened and tempered washers for high strength structural bolts and nuts (First Revision)

M 16 to M 36/ Type A, Type B, Type C

16900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 Table-1(Dimensions Type A- d1)	-	5000	For complete dimension test
3 Table-1(Dimensions Type A- d2)	-	5000	For complete dimension test
3 Table-1(Dimensions Type A- S)	-	5000	For complete dimension test
3 Table-2(Dimensions Type B&C- d)	-	5000	For complete dimension test
3 Table-2(Dimensions Type B&C- a)	-	5000	For complete dimension test
3 Table-2(Dimensions Type B&C- t)	-	5000	For complete dimension test
3 Table-2(Dimensions Type B&C- θ)	-	5000	For complete dimension test
7(Hardness)	-	500	-
8.1(Freedom from defect)	-	3400	For Galvanization and qualitative test
8.1(Uniformity of zinc coating)	-	500	For Galvanization and qualitative test
8.1(Mass of zinc coating)	-	500	For Galvanization and qualitative test
8.1(Knife test (Adhesion of coating))	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- d1)	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- d2)	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- S)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- d)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- a)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- t)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- θ)	-	5000	For complete dimensional and qualitative tests
7(Hardness)	-	500	-
8.1(Freedom from defect)	-	500	-
8.1(Uniformity of zinc coating)	-	500	-
8.1(Mass of zinc coating)	-	500	-
8.1(Knife test (Adhesion of coating))	-	5000	For complete dimensional and qualitative tests
5(Chemical Composition- Sulphur)	-	3000	For complete chemical test
5(Chemical Composition- Phosphorus)	-	3000	For complete test
3 Table-1(Dimensions Type A- d1)	-	5000	For complete dimensional tests
3 Table-1(Dimensions Type A- d2)	-	5000	For complete dimensional tests
3 Table-1(Dimensions Type A- S)	-	5000	For complete dimensional tests
3 Table-2(Dimensions Type B&C- d)	-	5000	For complete dimensional tests
3 Table-2(Dimensions Type B&C- a)	-	5000	For complete dimensional tests
3 Table-2(Dimensions Type B&C- t)	-	5000	For complete dimensional tests
3 Table-2(Dimensions Type B&C- θ)	-	5000	For complete dimensional tests
7(Hardness)	-	500	-
8.1(Freedom from defect)	-	5000	For complete dimension and qualitative tests
8.1(Uniformity of zinc coating)	-	500	-
8.1(Mass of zinc coating)	-	500	-
8.1(Knife test (Adhesion of coating))	-	5000	For complete dimension and qualitative tests
5(Chemical Composition- Sulphur)	-	3000	For complete chemical test - if required
5(Chemical Composition- Phosphorus)	-	3000	For complete chemical test - if required
3 Table-1(Dimensions Type A- d1)	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- d2)	-	5000	For complete dimensional and qualitative tests
3 Table-1(Dimensions Type A- S)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- d)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- a)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- t)	-	5000	For complete dimensional and qualitative tests
3 Table-2(Dimensions Type B&C- θ)	-	5000	For complete dimensional and qualitative tests
7(Hardness)	-	7000	For complete mechanical tests
8.1(Freedom from defect)	-	5000	For complete dimensional and qualitative tests
8.1(Uniformity of zinc coating)	-	500	-
8.1(Mass of zinc coating)	-	500	-
8.1(Knife test (Adhesion of coating))	-	5000	For complete dimensional and qualitative tests
5(Chemical Composition- Sulphur)	-	3000	For complete chemical tests - if required
5(Chemical Composition- Phosphorus)	-	3000	For complete chemical tests - if required

-
Included w.e.f. 21-09-2022.

316

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

Light Duty, Heavy Duty, Medium Duty, Extra Heavy Duty

14820 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 and Table 1(Dimensions of Frame - A)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - B)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - C)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - D)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - E)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - F)	-	10000	For complete dimensional tests
5.2(Dimensions of cover- Diameter)	-	10000	-
5.2(Clearance at top between the frame and the cover all round the periphery)	-	10000	-
5.2(Top surface ofthe frame and cover is in level)	-	10000	-
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	10000	-
5.2 and Fig 1(Clear cover to reinforcement)	-	10000	-
5.2 and Fig 1(Distance of housing from the edge)	-	10000	For complete dimensional tests
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests
7.4.1(Edge Protection and Finishing - Frame)	-	10000	-
7.4.2(Edge Protection and Finishing - Cover)	-	10000	-
7.4.2(Edge Protection and Finishing - Cover)	-	10000	-
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests
7.4.2(Edge Protection and Finishing - Cover)	-	10000	-
9.3 and Table and Annex C(Load Test)	-	8500	-
5.2 and Table 1(Dimensions of Frame - A)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - B)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - C)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - D)	-	10000	-
5.2 and Table 1(Dimensions of Frame - E)	-	10000	For complete dimensional tests
5.2 and Table 1(Dimensions of Frame - F)	-	10000	For complete dimensional tests
5.2(Dimensions of cover- Diameter)	-	10000	For complete dimensional tests and finish
5.2(Clearance at top between the frame and the cover all round the periphery)	-	10000	For complete dimensional tests
5.2(Top surface ofthe frame and cover is in level)	-	10000	For complete dimensional tests
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	10000	For complete dimensional tests
5.2 and Fig 1(Clear cover to reinforcement)	-	10000	For complete dimensional tests and finish
5.2 and Fig 1(Distance of housing from the edge)	-	10000	For complete dimensional tests
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	-
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
9.3 and Table and Annex C(Load Test)	-	8500	-
8(LIFTING HOOKS)	-	10000	For complete dimensional tests and finish
8(LIFTING HOOKS)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - A)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - B)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - C)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - D)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - E)	-	10000	For complete dimensional tests and finish
5.2 and Table 1(Dimensions of Frame - F)	-	10000	For complete dimensional tests and finish
5.2(Dimensions of cover- Diameter)	-	10000	For complete dimensional tests and finish
5.2(Clearance at top between the frame and the cover all round the periphery)	-	10000	For complete dimensional tests and finish
5.2(Top surface ofthe frame and cover is in level)	-	10000	For complete dimensional tests and finish
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	10000	For complete dimensional tests and finish
5.2 and Fig 1(Clear cover to reinforcement)	-	10000	For complete dimensional tests and finish
5.2 and Fig 1(Distance of housing from the edge)	-	10000	For complete dimensional tests and finish
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests and finish
7.4.1(Edge Protection and Finishing - Frame)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
7.4.2(Edge Protection and Finishing - Cover)	-	10000	For complete dimensional tests and finish
9.3 and Table and Annex C(Load Test)	-	8500	-
8(LIFTING HOOKS)	-	10000	For complete dimensional tests and finish
8(LIFTING HOOKS)	-	10000	For complete dimensional tests and finish

-
Included w.e.f. 21-09-2022.

317

IS 13095 (2020)

Butterfly Valves for General Purposes ( First Revision )

50 mm to 650 mm

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0( NOMINAL SIZES )	-	2500	For dimensional and qualitative Tests
7.0(NOMINAL PRESSURES)	-	5000	For complete hydrostatic test
9.1.1 ( Double Flanged Body Ends)	-	2500	For dimensional and qualitative Tests
9.2.2(Wafer Body Ends)	-	2500	For dimensional and qualitative Tests
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-	2500	For dimensional and qualitative Tests
11.0(Bodies)	-	2500	For dimensional and qualitative Tests
12.0(DISC AND SHAFT)	-	2500	For dimensional and qualitative Tests
14.0(BEARINGS)	-	2500	For dimensional and qualitative Tests
14.2(BEARINGS)	-	2500	For dimensional and qualitative Tests
14.3(BEARINGS)	-	2500	For dimensional and qualitative Tests
17.2(Body Test)	-	5000	For complete Hydrostatic Tests
17.4(Disc Strength Test)	-	5000	For complete Hydrostatic Tests
17.3(Seat Test)	-	5000	For complete Hydrostatic Tests
Cl. 15 Table 2(Materials)	-	7500	For each component (CI, Stainless Steel) - If required
6.0( NOMINAL SIZES )	-	2500	For dimensional and qualitative Tests
7.0(NOMINAL PRESSURES)	-	5000	For complete hydrostatic test
9.1.1 ( Double Flanged Body Ends)	-	2500	For dimensional and qualitative Tests
9.2.2(Wafer Body Ends)	-	2500	For dimensional and qualitative Tests
10.1 -Table1 (FACE TO FACE DIMENSIONS)	-	2500	For dimensional and qualitative Tests
11.0(Bodies)	-	2500	For dimensional and qualitative Tests
12.0(DISC AND SHAFT)	-	2500	For dimensional and qualitative Tests
14.0(BEARINGS)	-	2500	For dimensional and qualitative Tests
14.2(BEARINGS)	-	2500	For dimensional and qualitative Tests
14.3(BEARINGS)	-	2500	For dimensional and qualitative Tests
17.2(Body Test)	-	5000	For complete Hydrostatic Tests
17.4(Disc Strength Test)	-	5000	For complete Hydrostatic Tests
17.3(Seat Test)	-	5000	For complete Hydrostatic Tests
Cl. 15 Table 2(Materials)	-	7500	For each component (CI, Stainless Steel) - If required
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Flange-D)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Flange-b)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-d4)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges-IS 6418 (Table 2/3/6/7/10)- Rasied Face-f)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Bolting )	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -Nos. )	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -d2)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Drilling -k)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck -d3)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) - Integral Grey Cast Iron Flanges- IS 6418 (Table 2/3/6/7/10)- Neck- r)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-D)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Flange-b)	-	2000	--
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-d4)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Rasied Face-f)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Bolting)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -Nos. )	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -d2 )	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Drilling -k)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck -d3)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Malleable Cast Iron Integral Flanges- IS 6418 (Table 4/8/11)- Neck-r)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Pipe O.D.- d1)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - D)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Flange - b)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - d4)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Raised Face - f)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Bolting)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling - Nos.)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -d2)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Steel Plate Flanges for Welding- IS 6392 (Table 3/5/11/17/23/28)- Drilling -k)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange -D)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Flange - b)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - d4)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Raised Face - f)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Bolting)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling - Nos.)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -d2)	-	2000	-
9-Annex B(BODY ENDS ( Double Flanged Body Ends/Wafer Body Ends) -Integral Steel Flanges- IS 6392 (Table 15/21/26)- Drilling -k)	-	2000	-

-
-

318

IS 14329 (1995)

Malleable iron castings - Specification

WM350 and WM400,BM300, BM320 and BM350, PM 450 to PM700

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.2.1, 10.1, Table 1(Nominal diameter)	-	250	-
9.2.1, 10.1, Table 1(Tolerances on nominal diameter)	-	2000	-
9.2.1, 10.1, Table 1(Shank Dimensions, Diameter)	-	2000	-
9.2.1, 10.1, Table 1(Shank Dimensions, Length)	-	2000	-
9.2.1, 10.1, Table 1(Gauge length)	-	2000	-
9.2.1, 10.1, Table 1(Length)	-	2000	-
9.2.1, 10.1, Table 1(Radius at shoulder)	-	2000	-
10.1(Tensile Test)	-	2000	-
10.2(Hardness Test)	-	500	-
8.0(FREEDOM FROM DEFECTS)	-	500	For complete hardness and qualitative tests

-
Included w.e.f. 21-09-2022.

319

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

Water for Construction Purpose,Compressive strength fo

2500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.1(Average Compressive Strength)	-	2500	-
16.1(Average Compressive Strength)	-	2500	-
Cl 5.4 .2(pH)	-	300	-
Cl 5.4 Table 1 (iii)(Sulphate)	-	300	-
Cl 5.4 Table 1 (ii)(Inorganic Solids)	-	300	-
Cl 5.4 Table 1 (i)(Organic Solids)	-	300	-
Cl 5.4 Table 1 (v)(Suspended Matter)	-	300	-
5.4-(b)-IS: 3025 (P-23)(Volume of 0.02 N H2SO4 to neutralized 100 ml of water using mixed indicator)	-	1100	-
5.4-(a)-IS: 3025 (P-22)(Volume of 0.02 N NaOH to neutralized 100 ml of water using phenolphthalein indicator)	-	1100	-
16.1(Average Compressive Strength)	-	2500	-
Cl 5.4 .2(pH)	-	300	-
Cl 5.4 Table 1 (iii)(Sulphate)	-	300	-
Cl 5.4 Table 1 (ii)(Inorganic Solids)	-	300	-
Cl 5.4 Table 1 (i)(Organic Solids)	-	300	-
Cl 5.4 Table 1 (v)(Suspended Matter)	-	300	-
5.4-(b)-IS: 3025 (P-23)(Volume of 0.02 N H2SO4 to neutralized 100 ml of water using mixed indicator)	-	1100	-
5.4-(a)-IS: 3025 (P-22)(Volume of 0.02 N NaOH to neutralized 100 ml of water using phenolphthalein indicator)	-	1100	-
Cl 5.4 Table 1 (iv)(Chloride)	-	300	-

-
Included w.e.f. 21-09-2022.

320

IS 410 (1977)

Specification for cold rolled brass sheet, strip and foil (Third Revision)

Annealed, Quarter Hard, Half Hard, Hard, Extra Hard, Sp

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1.1(Tensile Test)	-	2000	For tensile and elongation test
Table-2(Vickers Hardness)	-	500	-
6.1 Table-1(Cu)	-	2000	-
Table-2(Thickness)	-	750	-
6.1 Table-1(Pb)	-	2000	-
6.1 Table-1(Fe)	-	2000	-
6.1 Table-1(Total impurities including iron)	-	2000	-
6.1 Table-1(Zn)	-	2000	-
4.0(Freedom from defects)	-	2000	-
Table-2(Elongation)	-	2000	For tensile and elongation test

-
Included w.e.f. 21-09-2022.

321

IS 16176 (2014)

Ratchet pipe threader for taper pipe threads (R - Series) - Specification

.½” to 6”

13700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions)	-	9000	For complete dimensional and qualitative tests.
6.2(Hardness)	-	700	-
9.1(Performance of thread testing)	-	4000	For complete thread parameters testing
4(Dimensions)	-	9000	For complete dimensional and qualitative tests.
6.2(Hardness)	-	700	For Hardness Test
9.1(Performance of thread testing)	-	4000	For complete thread parameters testing
7(Workmanship & Finish)	-	9000	For complete dimensional and qualitative tests.
5(Materials)	-	3500	For complete chemical tests (if required)
9.4(Measurement of gauging of threads)	-	4000	For complete gauging parameters test
9.3(Measurement of length of external thread)	-	4000	For complete gauging parameters test
9.2(Cutting of threads on a pipe testing)	-	4000	For complete gauging parameters test
6.3(To check the functioning of ratchet handle by rotating the locking pin 180°.)	-	9000	For complete dimensional and qualitative tests.
6.1(Manufacturing Quality (Visual))	-	9000	For complete dimensional and qualitative tests.
4(Dimensions)	-	-	-
6.2(Hardness)	-	-	-
9.1(Performance of thread testing)	-	-	-
7(Workmanship & Finish)	-	-	-
5(Materials)	-	-	-
9.4(Measurement of gauging of threads)	-	-	-
9.3(Measurement of length of external thread)	-	-	-
9.2(Cutting of threads on a pipe testing)	-	-	-
6.3(To check the functioning of ratchet handle by rotating the locking pin 180°.)	-	-	-
6.1(Manufacturing Quality (Visual))	-	-	-

-
Included w.e.f. 21-09-2022.

322

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

Annealed (Soft)(O),Half Hard(HB) and Hard (HD),GR 1,GR2

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Dimension and Tolerances)	-	2500	For complete dimension and qualitative tests.
9.1 Table-2(Tensile Strength)	-	2500	-
9.2(Vickers Hardness)	-	2500	-
8.1 Table 1(Cu)	-	3000	For complete chemical tests
8.1 Table 1(Pb)	-	3000	For complete chemical tests
8.1 Table 1(Fe)	-	3000	-
8.1 Table 1(Total other impurities excluding iron)	-	3000	For complete chemical tests
8.1 Table 1(Zn)	-	3000	For complete chemical tests
10.1(Mercurous Nitrate Test)	-	3000	For complete chemical tests
5.0(Freedom from defects)	-	2500	For complete dimension and qualitative tests.

-
Included w.e.f. 21-09-2022.

Bureau of Indian Standards

The National Standards Body of India

JBS TESTING SOLUTIONS PVT LTD (27), JALANDHAR

PLOT NO. 27, STREET NO. 2, ADJOINING FOCAL POINT ROAD, TRANSPORT NAGAR, JALANDHAR, PUNJAB, JALANDHAR, Jalandhar, Punjab, 144004

9988862929 jbstestingsolutions@gmail.com

Scope List