BIS - LIMS (Laboratory Information Management System)

Hi Physix Laboratory India Private Limited, Pune

B-32/1/2, MIDC, Industrial Area, Ranjangaon, Pune, Pune, Pune, Maharashtra, 412220

8552003805 infohplindia@bureauveritas.com

Scope List

Reset

139 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 14286 : Part 1 : Sec 1 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-1: Special requirements for testing of crystalline silicon photovoltaic PV modules Third Revision

1835000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	0	-
Cl-11.1(Visual inspection)	-	20000	-
Cl-11.2(Maximum power determination)	-	30000	-
Cl-11.3(Insulation test)	-	15000	-
Cl-11.4(Measurement of temperature coefficients)	-	60000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC)	-	30000	-
Cl-11.7(Performance at low irradiance)	-	30000	-
Cl-11.8(Outdoor exposure test)	-	30000	-
Cl-11.9(Hot-spot endurance test)	-	200000	-
Cl-11.10(UV preconditioning test)	-	150000	-
Cl-11.11(Thermal cycling test)	-	250000	-
Cl-11.12(Humidity-freeze test)	-	100000	-
Cl-11.13(Damp heat test)	-	150000	-
Cl-11.14(Robustness of terminations test)	-	15000	-
Cl-11.15(Wet leakage current tes)	-	20000	-
Cl-11.16(Static mechanical load test)	-	40000	-
Cl-11.17(Hail test)	-	20000	-
Cl-11.18(Bypass diode thermal test)	-	80000	-
Cl-11.19(Stabilization)	-	150000	-
5(Marking and documentation)	-	5000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	120000	-
11.21(Potential induced degradation test (MQT 21))	-	300000	-
11.22(Bending test (MQT 22))	-	20000	-

20 Jun, 2028

-
-

IS 14286 : Part 1 : Sec 2 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-2: Special requirements for testing of thin-film Cadmium Telluride CdTe based photovoltaic PV modules Third Revision

1985000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	0	-
Cl-11.1(Visual inspection)	-	20000	-
Cl-11.2(Maximum power determination)	-	30000	-
Cl-11.3(Insulation tes)	-	15000	-
Cl-11.4(Measurement of temperature coefficients)	-	60000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC and NMOT)	-	30000	-
Cl-11.7(Performance at low irradiance)	-	30000	-
Cl-11.8(Outdoor exposure test)	-	30000	-
Cl-11.9(Hot-spot endurance test)	-	200000	-
Cl-11.10(UV preconditioning test)	-	150000	-
Cl-11.11(Thermal cycling test)	-	250000	-
Cl-11.12(Humidity-freeze test)	-	100000	-
Cl-11.13(Damp heat test)	-	150000	-
Cl-11.14(Robustness of terminations test)	-	15000	-
Cl-11.15(Wet leakage current test)	-	20000	-
Cl-11.16(Static mechanical load test)	-	40000	-
Cl-11.17(Hail test)	-	20000	-
Cl-11.18(Bypass diode testing)	-	80000	-
Cl-11.19(Stabilization)	-	300000	-
5(Marking and documentation)	-	5000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	120000	-
11.21(Potential induced degradation test (MQT 21))	-	300000	-
11.22(Bending test (MQT 22))	-	20000	-

20 Jun, 2028

-
-

IS 14286 : Part 1 : Sec 3 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic PV modules Third Revision

1985000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	0	-
Cl-11.1(Visual inspection)	-	20000	-
Cl-11.2(Maximum power determination)	-	30000	-
Cl-11.3(Insulation test)	-	15000	-
Cl-11.4(Measurement of temperature coefficients)	-	60000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC and NMOT)	-	30000	-
Cl-11.7(Performance at low irradiance)	-	30000	-
Cl-11.8(Outdoor exposure test)	-	30000	-
Cl-11.9(Hot-spot endurance test)	-	200000	-
Cl-11.10(UV preconditioning test)	-	150000	-
Cl-11.11(Thermal cycling test)	-	250000	-
Cl-11.12(Humidity-freeze test)	-	100000	-
Cl-11.13(Damp heat test)	-	150000	-
Cl-11.14(Robustness of terminations test)	-	15000	-
Cl-11.15(Wet leakage current test)	-	20000	-
Cl-11.16(Static mechanical load test)	-	40000	-
Cl-11.17(Hail test)	-	20000	-
Cl-11.18(Bypass diode testing)	-	80000	-
Cl-11.19(Stabilization)	-	300000	-
5(Marking and documentation)	-	5000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	120000	-
11.21(Potential induced degradation test (MQT 21))	-	300000	-
11.22(Bending test (MQT 22))	-	20000	-

20 Jun, 2028

-
-

IS 14286 : Part 1 : Sec 4 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-4: Special requirements for testing of thin-film CuInGASSe2 based photovoltaic PV modules Third Revision

1985000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	0	-
Cl-11.1(Visual inspection (MQT 01))	-	20000	-
Cl-11.2(Maximum power determination (MQT 02))	-	30000	-
Cl-11.3(Insulation test (MQT 03))	-	15000	-
Cl-11.4(Measurement of temperature coefficients (MQT 04))	-	60000	-
Cl-11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	0	-
Cl-11.6(Performance at STC (MQT 06.1) and NMOT (MQT 06.2)	-	30000	-
Cl-11.7(Performance at low irradiance (MQT 07))	-	30000	-
Cl-11.8(Outdoor exposure test (MQT 08))	-	30000	-
Cl-11.9(Hot-spot endurance test (MQT 09))	-	200000	-
Cl-11.10(UV preconditioning test (MQT 10))	-	150000	-
Cl-11.11(Thermal cycling test (MQT 11))	-	250000	-
Cl-11.12(As per IEC 61215-1:2016)	-	100000	11.12 (Humidity-freeze test (MQT 12))
Cl-11.13(Damp heat test (MQT 13))	-	150000	-
Cl-11.14(Robustness of terminations test (MQT 14))	-	15000	-
Cl-11.15(Robustness of terminations test (MQT 14))	-	20000	11.15 (Wet leakage current test (MQT 15))
Cl-11.16(Static mechanical load test (MQT 16))	-	40000	-
Cl-11.17(Hail test (MQT 17))	-	20000	-
Cl-11.18(Bypass diode testing (MQT 18))	-	80000	-
Cl-11.19(Stabilization (MQT 19))	-	300000	-
5(Marking and documentation)	-	5000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	120000	-
11.21(Potential induced degradation test (MQT 21))	-	300000	-
11.22(Bending test (MQT 22))	-	20000	-

20 Jun, 2028

-
-

IS 14286 : Part 1 (2023)

Terrestrial Photovoltaic PV Modules Design Qualification and Type Approval Part 1: Test Requirements (Third Revision)

1830000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Visual inspection (MQT 01))	-	20000	-
4.2(Maximum power determination (MQT 02))	-	30000	-
4.3(Insulation test (MQT 03))	-	15000	-
4.4(Measurement of temperature coefficients (MQT 04))	-	60000	-
4.5(Placeholder section, formerly NMOT)	-	0	-
4.6(Performance at STC (MQT 06.1))	-	30000	-
4.7(Performance at low irradiance (MQT 07))	-	30000	-
4.8(Outdoor exposure test (MQT 08))	-	30000	-
4.9(Hot-spot endurance test (MQT 09))	-	200000	-
4.10(UV preconditioning test (MQT 10))	-	150000	-
4.11(Thermal cycling test (MQT 11))	-	250000	-
4.12(2 Humidity-freeze test (MQT 12))	-	100000	-
4.13(Damp heat test (MQT 13))	-	150000	-
4.14(Robustness of terminations (MQT 14))	-	15000	-
4.15(5 Wet leakage current test (MQT 15))	-	20000	-
4.16(Static mechanical load test (MQT 16))	-	40000	-
4.17(Hail test (MQT 17))	-	20000	-
4.18(Bypass diode testing (MQT 18))	-	80000	-
4.19(Stabilization (MQT 19))	-	150000	-
4.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	120000	-
4.21(Potential induced degradation test (MQT 21))	-	300000	-
4.22(Bending test (MQT 22))	-	20000	-

20 Jun, 2028

-
-

IS/IEC 61730 : PART 1 (2023)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction (Second Revision)

396000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Classification, applications and intended use)	-	5000	-
6.2(Marking and documentation)	-	10000	-
6.3.2(Internal wiring)	-	15000	-
6.3.3(External wiring and cables)	-	15000	-
6.3.4(Module overcurrent protection rating)	-	15000	-
6.3.5(Connectors)	-	15000	-
6.3.6(Junction boxes)	-	15000	-
6.3.7(Frontsheets and backsheets)	-	15000	-
6.3.8(Insulation barriers)	-	10000	-
6.3.9(Electrical connections)	-	15000	-
6.3.10(Encapsulants)	-	15000	-
6.3.11(Bypass diodes)	-	15000	-
6.4(Mechanical and electromechanical connections)	-	15000	-
6.4.2(Screw connections)	-	10000	-
6.4.3(Rivets)	-	10000	-
6.4.4(Thread-cutting screws)	-	10000	-
6.4.5(Form/press/tight fit)	-	15000	-
6.4.6(Connections by adhesives)	-	15000	-
6.4.7(Other connections)	-	15000	-
6.5.2(Polymeric materials)	-	15000	-
6.5.2.3(Flammability)	-	15000	-
6.5.3.2(Current-carrying parts)	-	15000	-
6.5.4(Adhesives)	-	15000	-
6.6.2(Protection against accessibility to hazardous live parts)	-	10000	-
6.6.3(Insulation coordination)	-	15000	-
6.6.3.2.1(Pollution degree)	-	5000	-
6.6.3.3(Creepage distance)	-	8000	-
6.6.3.4(Clearance)	-	8000	-
6.6.4(Distance through functional and relied upon insulation)	-	15000	-
6.6.4.3(Cemented joints)	-	10000	-
6.6.4.4(Distance through functional insulation)	-	15000	-

20 Jun, 2028

-
-

IS/IEC 61730 : PART 2 (2023)

Photovoltaic (PV) Module - Safety Qualification Part 2 Requirements for Testing (Second Revision)

1765000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.2(Visual inspection MST 01)	-	20000	-
10.3(Performance at STC MST 02)	-	30000	-
10.4(Maximum power determination MST 03)	-	30000	-
10.5(Insulation thickness test MST 04)	-	55000	-
10.6(Durability of markings MST 05)	-	5000	-
10.7(Sharp edge test MST 06)	-	10000	-
10.8(Bypass diode functionality test MST 07)	-	20000	-
10.9(Accessibility test MST 11)	-	5000	-
10.1(Cut susceptibility test MST 12)	-	5000	-
10.11(Continuity test of equipotential bonding MST 13)	-	5000	-
10.12(Impulse voltage test MST 14)	-	30000	-
10.13(Insulation test MST 16)	-	15000	-
10.14(Wet leakage current test MST 17)	-	20000	-
10.16(Hot-spot endurance test MST 22)	-	200000	-
10.17(Fire test MST 23)	-	50000	-
10.18(Ignitability test MST 24)	-	145000	-
10.19(Bypass diode thermal test MST 25)	-	80000	-
10.20(Reverse current overload test MST 26)	-	20000	-
10.21(Module breakage test MST 32)	-	10000	-
10.22(Screw connections test MST 33)	-	5000	-
10.23(Static mechanical load test MST 34)	-	40000	-
10.24(Peel test MST 35)	-	75000	-
10.25(Lap shear strength test MST 36)	-	75000	-
10.26(Materials creep test MST 37)	-	45000	-
10.27(Robustness of terminations test MST 42)	-	15000	-
10.28(Thermal cycling test MST 51)	-	250000	-
10.29(Humidity freeze test MST 52)	-	100000	-
10.30(Damp heat test MST 53)	-	150000	-
10.31(UV test MST 54)	-	150000	-
10.32(Cold conditioning test MST 55)	-	25000	-
10.33(Dry heat conditioning test MST 56)	-	50000	-
10.34(Evaluation of insulation coordination MST 57)	-	30000	-

20 Jun, 2028

-
-

IS 10322 (Part 5/Sec 5) (2026)

Luminaires Part 5: Particular requirements Section 5: Floodlights (Second Revision)

136500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.5(Marking)	-	2500	-
Cl-5.6(Construction)	-	28000	-
Cl-5.6.8.1(Protection by the use of glass that fractures into small pieces)	-	0	-
5.6.8.2(Protection by the use of high impact resistant glass (high mechanical strength.))	-	0	-
Cl-5.6.8.2.1(Thermal endurance test)	-	0	-
Cl-5.7(Creepage distances and clearances)	-	2500	-
Cl-5.8(Provision for earthing)	-	2500	-
Cl-5.9(Terminals)	-	2500	-
Cl-5.10(External and internal wiring)	-	6500	-
Cl-5.11(Protection against electric shock)	-	2500	-
Cl-5.12(Endurance tests and thermal tests)	-	35000	-
Cl-5.13(Resistance to dust and moisture)	-	25000	-
Cl-5.14(Insulation resistance and electric strength)	-	9500	-
Cl-5.15(Resistance to heat, fire and tracking)	-	20000	-

20 Jun, 2028

-
included w.e.f 04.08.2026

IS/IEC 62368 : Part 1 (2023)

Audio Video Information and Communication Technology Equipment - Part 1: Safety Requirements (Second Revision)

175000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General- materials, components)	-	1000	-
Cl-4.2(Energy source classifications)	-	500	-
Cl-4.3(Protection against energy sources)	-	1000	-
Cl-4.4(Safeguards)	-	1000	-
Cl-4.5(Explosion)	-	2000	-
Cl-4.6(Fixing of conductors and conductive parts)	-	1000	-
Cl-4.7(Equipment for direct insertion into mains socket-outlets)	-	1000	-
Cl-4.8(Equipment containing coin or button cell batteries)	-	1000	-
Cl-4.9(Likelihood of fire or shock due to entry of conductive objects)	-	1000	-
Cl-4.10(Components requirements)	-	3000	-
Cl-5.1(General- Electrically-caused injury)	-	2000	-
Cl-5.2(Classification and limits of electrical energy sources)	-	3000	-
Cl-5.3(Protection against electrical energy sources)	-	1000	-
Cl-5.4(Insulation materials and requirements)	-	3000	-
Cl-5.5(Components as safeguards)	-	2000	-
Cl-5.6(Protective conductor)	-	3000	-
Cl-5.7(Prospective touch voltage, touch current and protective conductor current)	-	3000	-
Cl-5.8(Backfeed safeguard in battery backed up supplies)	-	2000	-
Cl-6.1(General- Electrically-caused fire)	-	2000	-
Cl-6.2(Classification of power sources and potential ignition sources)	-	2000	-
Cl-6.3(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	2000	-
Cl-6.4(Safeguards against fire under single fault conditions)	-	2000	-
Cl-6.5(Internal and external wiring)	-	1000	-
Cl-7.1(General- Injury caused by hazardous substances)	-	500	-
Cl-7.2(Reduction of exposure to hazardous substances)	-	1000	-
Cl-7.3(Ozone exposure)	-	500	-
Cl-7.4(Use of personal safeguards or personal protective equipment (PPE)	-	500	-
Cl-7.5(Use of instructional safeguards and instructions)	-	500	-
Cl-8.1(General- Mechanically-caused injury)	-	1000	-
Cl-8.2(Mechanical energy source classifications)	-	1000	-
Cl-8.3(Safeguards against mechanical energy sources)	-	1000	-
Cl-8.4(Safeguards against parts with sharp edges and corners)	-	1000	-
Cl-8.5(Safeguards against moving parts)	-	1000	-
Cl-8.6(Stability of equipment)	-	2000	-
Cl-8.7(Equipment mounted to a wall, ceiling or other structure)	-	2000	-
Cl-8.8(Handle strength)	-	1000	-
Cl-8.9(Wheels or casters attachment requirements)	-	1000	-
Cl-8.10(Carts, stands, and similar carriers)	-	1000	-
Cl-8.11(Mounting means for slide-rail mounted equipment (SRME))	-	1000	-
Cl-9.1(General-Thermal burn injury)	-	1000	-
Cl-9.2(Thermal energy source classifications)	-	1000	-
Cl-9.3(Touch temperature limits)	-	2000	-
Cl-9.4(Safeguards against thermal energy sources)	-	1000	-
Cl-9.5(Requirements for safeguards)	-	1000	-
Cl-9.6(Requirements for wireless power transmitters)	-	2000	-
Cl-10.1(General-Radiation)	-	500	-
Cl-10.2(Radiation energy source classifications)	-	500	-
Cl-10.3(Safeguards against laser radiation)	-	1000	-
Cl-10.4("Safeguards against optical radiation from lamps and lamp systems (including LED types)")	-	1000	-
Cl-10.5(Safeguards against X-radiation)	-	500	-
Cl-10.6(Safeguards against acoustic energy sources)	-	500	-
Annex A(Examples of equipment within the scope of this document)	-	500	-
Annex B(General- Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	2000	-
Annex B-2(Normal operating conditions)	-	1000	-
Annex B-3(Simulated abnormal operating conditions)	-	1000	-
Annex B-4(Simulated single fault conditions)	-	2000	-
Annex C-1(Protection of materials in equipment from UV radiation)	-	0	-
Annex C-2(UV light conditioning test)	-	0	-
Annex D-1(Impulse test generators)	-	3000	-
Annex D-2(Antenna interface test generator)	-	3000	-
Annex D-3(Electronic pulse generator)	-	0	-
Annex E-1(Electrical energy source classification for audio signals)	-	2000	-
Annex E-2(Audio signals used during test)	-	2000	-
Annex E-3(Operating conditions of equipment containing an audio amplifier)	-	2000	-
Annex F-1(General-Equipment markings, instructions, and instructional safeguards)	-	1000	-
Annex F-2(Letter symbols and graphical symbols)	-	1000	-
Annex F-3(Equipment markings)	-	2000	-
Annex F-4(Instructions)	-	1000	-
Annex F-5(Instructional safeguards)	-	1000	-
Annex G-1(Switches)	-	1000	-
Annex G-2(Relays)	-	1000	-
Annex G-3(Protective devices)	-	1000	-
Annex G-4(Connectors)	-	1000	-
Annex G-5(Wound components)	-	2000	-
Annex G-6(Wire insulation)	-	1000	-
Annex G-7(Mains power supply cords and interconnection cables)	-	2000	-
Annex G-8(Varistors)	-	500	-
Annex G-9(Integrated circuit (IC) current limiters)	-	1000	-
Annex G-10(Resistors)	-	500	-
Annex G-11(Capacitors and RC units)	-	1000	-
Annex G-12(Optocouplers)	-	500	-
Annex G-13(Printed boards)	-	2000	-
Annex G-14(Coatings on component terminals)	-	1000	-
Annex G-15(Pressurized liquid filled components or LFC assemblies)	-	1000	-
Annex G-16(IC that includes a capacitor discharge function (ICX))	-	1000	-
Annex H-1(General- Criteria for telephone ringing signals)	-	1000	-
Annex H-2(Method A)	-	1000	-
Annex H-3(Method B)	-	1000	-
Annex I(Overvoltage categories (see IEC 60364-4-44))	-	500	-
Annex J-1(General-Insulated winding wires for use without interleaved insulation)	-	1000	-
Annex J-2(Type tests)	-	2000	-
Annex J-3(Testing during manufacturing)	-	2000	-
Annex K-1(General- Safety interlocks)	-	500	-
Annex K-2(Components of the safety interlock safeguard mechanism)	-	500	-
Annex K-3(Inadvertent change of operating mode)	-	500	-
Annex K-4(Interlock safeguard override)	-	500	-
Annex K-5(Fail-safe)	-	500	-
Annex K-6(Mechanically operated safety interlocks)	-	0	-
Annex K-7(Interlock circuit isolation)	-	0	-
Annex L-1(General requirements)	-	500	-
Annex L-2(Permanently connected equipment)	-	1000	-
Annex L-3()	-	1000	-
Annex L-4(Single-phase equipment)	-	1000	-
Annex L-5(Three-phase equipment)	-	1000	-
Annex L-6(Switches as disconnect devices)	-	1000	-
Annex L-7(Plugs as disconnect devices)	-	1000	-
Annex L-8(Multiple power sources)	-	1000	-
Annex L-9(Compliance criteria)	-	1000	-
Annex M-1(General requirements)	-	500	-
Annex M-2(Safety of batteries and their cells)	-	500	-
Annex M-3(Protection circuits for batteries provided within the equipment)	-	500	-
Annex M-4(Additional safeguards for equipment containing a secondary lithium battery)	-	500	-
Annex M-5(Risk of burn due to short-circuit during carrying)	-	1000	-
Annex M-6(Safeguards against short-circuits)	-	500	-
Annex M-7(Risk of explosion from lead acid and NiCd batteries)	-	0	-
Annex M-8("Protection against internal ignition from external spark sources of rechargeable batteries with aqueous electrolyte")	-	0	-
Annex M-9(Preventing electrolyte spillage)	-	500	-
Annex M-10(Instructions to prevent reasonably foreseeable misuse)	-	500	-
Annex N(Electrochemical potentials (V))	-	500	-
Annex O(Measurement of creepage distances and clearances)	-	1000	-
Annex P-1(General-Safeguards against conductive objects)	-	500	-
Annex P-2(Safeguards against entry or consequences of entry of a foreign object)	-	1000	-
Annex P-3(Safeguards against spillage of internal liquids)	-	1000	-
Annex P-4(Metallized coatings and adhesives securing parts)	-	500	-
Annex Q-1(Limited power source)	-	2000	-
Annex R(Limited short-circuit test)	-	2000	-
Annex S-1(Flammability test for fire enclosure and fire barrier materials of equipment where the steady state power does not exceed 4 000 W)	-	2000	-
Annex S-2(Flammability test for fire enclosure and fire barrier integrity)	-	2000	-
Annex S-3(Flammability tests for the bottom of a fire enclosure)	-	1999.99	-
Annex S-4(Flammability classification of materials)	-	1000	-
Annex S-5(Flammability test for fire enclosure materials of equipment with a steady state power exceeding 4 000 W)	-	1000	-
Annex S-6(Grille covering material, cloth, and reticulated foam)	-	500	-
Annex T-1(General-Mechanical strength tests)	-	500	-
Annex T-2(Steady force test, 10 N)	-	500	-
Annex T-3(Steady force test, 30 N)	-	1000	-
Annex T-4(Steady force test, 100 N)	-	1000	-
Annex T-5(Steady force test, 250 N)	-	1000	-
Annex T-6(Enclosure impact test)	-	1000	-
Annex T-7(Drop test)	-	1000	-
Annex T-8(Stress relief test)	-	2000	-
Annex T-9(Glass impact test)	-	1000	-
Annex T-10(Glass fragmentation test)	-	1000	-
Annex T-11(Test for telescoping or rod antennas)	-	1000	-
Annex U("Mechanical strength of CRTs and protection against the effects of implosion")	-	0	-
Annex V-1(Accessible parts of equipment)	-	1000	-
Annex V-2(Accessible part criterion)	-	1000	-
Annex W(Comparison of terms introduced in this document)	-	1000	-
Annex X("Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420 V peak (300 V RMS)")	-	1000	-
Annex Y-1(General- Construction requirements for outdoor enclosures)	-	1000	-
Annex Y-2(Resistance to UV radiation)	-	0	-
Annex Y-3(Resistance to corrosion)	-	2000	-
Annex Y-4(Gaskets)	-	2000	-
Annex Y-5(Protection of equipment within an outdoor enclosure)	-	2000	-
Annex Y-6(Mechanical strength of enclosures)	-	1000	-
Annex Q-2(Test for external circuits – paired conductor cable)	-	1000	-
Cl-4.1(General- materials, components)	-	0	-
Cl-4.2(Energy source classifications)	-	0	-
Cl-4.3(Protection against energy sources)	-	0	-
Cl-4.4(Safeguards)	-	0	-
Cl-4.5(Explosion)	-	0	-
Cl-4.6(Fixing of conductors and conductive parts)	-	0	-
Cl-4.7(Equipment for direct insertion into mains socket-outlets)	-	0	-
Cl-4.8(Equipment containing coin or button cell batteries)	-	0	-
Cl-4.9(Likelihood of fire or shock due to entry of conductive objects)	-	0	-
Cl-4.10(Components requirements)	-	0	-
Cl-5.1(General- Electrically-caused injury)	-	0	-
Cl-5.2(Classification and limits of electrical energy sources)	-	0	-
Cl-5.3(Protection against electrical energy sources)	-	0	-
Cl-5.4(Insulation materials and requirements)	-	0	-
Cl-5.5(Components as safeguards)	-	0	-
Cl-5.6(Protective conductor)	-	0	-
Cl-5.7(Prospective touch voltage, touch current and protective conductor current)	-	0	-
Cl-5.8(Backfeed safeguard in battery backed up supplies)	-	0	-
Cl-6.1(General- Electrically-caused fire)	-	0	-
Cl-6.2(Classification of power sources and potential ignition sources)	-	0	-
Cl-6.3(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	0	-
Cl-6.4(Safeguards against fire under single fault conditions)	-	0	-
Cl-6.5(Internal and external wiring)	-	0	-
Cl-7.1(General- Injury caused by hazardous substances)	-	0	-
Cl-7.2(Reduction of exposure to hazardous substances)	-	0	-
Cl-7.3(Ozone exposure)	-	0	-
Cl-7.4(Use of personal safeguards or personal protective equipment (PPE)	-	0	-
Cl-7.5(Use of instructional safeguards and instructions)	-	0	-
Cl-8.1(General- Mechanically-caused injury)	-	0	-
Cl-8.2(Mechanical energy source classifications)	-	0	-
Cl-8.3(Safeguards against mechanical energy sources)	-	0	-
Cl-8.4(Safeguards against parts with sharp edges and corners)	-	0	-
Cl-8.5(Safeguards against moving parts)	-	0	-
Cl-8.6(Stability of equipment)	-	0	-
Cl-8.7(Equipment mounted to a wall, ceiling or other structure)	-	0	-
Cl-8.8(Handle strength)	-	0	-
Cl-8.9(Wheels or casters attachment requirements)	-	0	-
Cl-8.10(Carts, stands, and similar carriers)	-	0	-
Cl-8.11(Mounting means for slide-rail mounted equipment (SRME))	-	0	-
Cl-9.1(General-Thermal burn injury)	-	0	-
Cl-9.2(Thermal energy source classifications)	-	0	-
Cl-9.3(Touch temperature limits)	-	0	-
Cl-9.4(Safeguards against thermal energy sources)	-	0	-
Cl-9.5(Requirements for safeguards)	-	0	-
Cl-9.6(Requirements for wireless power transmitters)	-	0	-
Cl-10.1(General-Radiation)	-	0	-
Cl-10.2(Radiation energy source classifications)	-	0	-
Cl-10.3(Safeguards against laser radiation)	-	0	-
Cl-10.4("Safeguards against optical radiation from lamps and lamp systems (including LED types)")	-	0	-
Cl-10.5(Safeguards against X-radiation)	-	0	-
Cl-10.6(Safeguards against acoustic energy sources)	-	0	-
Annex A(Examples of equipment within the scope of this document)	-	0	-
Annex B(General- Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	0	-
Annex B-2(Normal operating conditions)	-	0	-
Annex B-3(Simulated abnormal operating conditions)	-	0	-
Annex B-4(Simulated single fault conditions)	-	0	-
Annex D-1(Impulse test generators)	-	0	-
Annex D-2(Antenna interface test generator)	-	0	-
Annex E-1(Electrical energy source classification for audio signals)	-	0	-
Annex E-2(Audio signals used during test)	-	0	-
Annex E-3(Operating conditions of equipment containing an audio amplifier)	-	0	-
Annex F-1(General-Equipment markings, instructions, and instructional safeguards)	-	0	-
Annex F-2(Letter symbols and graphical symbols)	-	0	-
Annex F-3(Equipment markings)	-	0	-
Annex F-4(Instructions)	-	0	-
Annex F-5(Instructional safeguards)	-	0	-
Annex G-1(Switches)	-	0	-
Annex G-2(Relays)	-	0	-
Annex G-3(Protective devices)	-	0	-
Annex G-4(Connectors)	-	0	-
Annex G-5(Wound components)	-	0	-
Annex G-6(Wire insulation)	-	0	-
Annex G-7(Mains power supply cords and interconnection cables)	-	0	-
Annex G-8(Varistors)	-	0	-
Annex G-9(Integrated circuit (IC) current limiters)	-	0	-
Annex G-10(Resistors)	-	0	-
Annex G-11(Capacitors and RC units)	-	0	-
Annex G-12(Optocouplers)	-	0	-
Annex G-13(Printed boards)	-	0	-
Annex G-14(Coatings on component terminals)	-	0	-
Annex G-15(Pressurized liquid filled components or LFC assemblies)	-	0	-
Annex G-16(IC that includes a capacitor discharge function (ICX))	-	0	-
Annex H-1(General- Criteria for telephone ringing signals)	-	0	-
Annex H-2(Method A)	-	0	-
Annex H-3(Method B)	-	0	-
Annex I(Overvoltage categories (see IEC 60364-4-44))	-	0	-
Annex J-1(General-Insulated winding wires for use without interleaved insulation)	-	0	-
Annex J-2(Type tests)	-	0	-
Annex J-3(Testing during manufacturing)	-	0	-
Annex K-1(General- Safety interlocks)	-	0	-
Annex K-2(Components of the safety interlock safeguard mechanism)	-	0	-
Annex K-3(Inadvertent change of operating mode)	-	0	-
Annex K-4(Interlock safeguard override)	-	0	-
Annex K-5(Fail-safe)	-	0	-
Annex K-6(Mechanically operated safety interlocks)	-	0	-
Annex K-7(Interlock circuit isolation)	-	0	-
Annex L-1(General requirements)	-	0	-
Annex L-2(Permanently connected equipment)	-	0	-
Annex L-3()	-	0	-
Annex L-4(Single-phase equipment)	-	0	-
Annex L-5(Three-phase equipment)	-	0	-
Annex L-6(Switches as disconnect devices)	-	0	-
Annex L-7(Plugs as disconnect devices)	-	0	-
Annex L-8(Multiple power sources)	-	0	-
Annex L-9(Compliance criteria)	-	0	-
Annex M-1(General requirements)	-	0	-
Annex M-2(Safety of batteries and their cells)	-	0	-
Annex M-3(Protection circuits for batteries provided within the equipment)	-	0	-
Annex M-4(Additional safeguards for equipment containing a secondary lithium battery)	-	0	-
Annex M-5(Risk of burn due to short-circuit during carrying)	-	0	-
Annex M-6(Safeguards against short-circuits)	-	0	-
Annex M-9(Preventing electrolyte spillage)	-	0	-
Annex M-10(Instructions to prevent reasonably foreseeable misuse)	-	0	-
Annex N(Electrochemical potentials (V))	-	0	-
Annex O(Measurement of creepage distances and clearances)	-	0	-
Annex P-1(General-Safeguards against conductive objects)	-	0	-
Annex P-2(Safeguards against entry or consequences of entry of a foreign object)	-	0	-
Annex P-3(Safeguards against spillage of internal liquids)	-	0	-
Annex P-4(Metallized coatings and adhesives securing parts)	-	0	-
Annex Q-1(Limited power source)	-	0	-
Annex R(Limited short-circuit test)	-	0	-
Annex S-1(Flammability test for fire enclosure and fire barrier materials of equipment where the steady state power does not exceed 4 000 W)	-	0	-
Annex S-2(Flammability test for fire enclosure and fire barrier integrity)	-	0	-
Annex S-3(Flammability tests for the bottom of a fire enclosure)	-	0	-
Annex S-4(Flammability classification of materials)	-	0	-
Annex S-5(Flammability test for fire enclosure materials of equipment with a steady state power exceeding 4 000 W)	-	0	-
Annex S-6(Grille covering material, cloth, and reticulated foam)	-	0	-
Annex T-1(General-Mechanical strength tests)	-	0	-
Annex T-2(Steady force test, 10 N)	-	0	-
Annex T-3(Steady force test, 30 N)	-	0	-
Annex T-4(Steady force test, 100 N)	-	0	-
Annex T-5(Steady force test, 250 N)	-	0	-
Annex T-6(Enclosure impact test)	-	0	-
Annex T-7(Drop test)	-	0	-
Annex T-8(Stress relief test)	-	0	-
Annex T-9(Glass impact test)	-	0	-
Annex T-10(Glass fragmentation test)	-	0	-
Annex T-11(Test for telescoping or rod antennas)	-	0	-
Annex V-1(Accessible parts of equipment)	-	0	-
Annex V-2(Accessible part criterion)	-	0	-
Annex W(Comparison of terms introduced in this document)	-	0	-
Annex X("Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420 V peak (300 V RMS)")	-	0	-
Annex Y-1(General- Construction requirements for outdoor enclosures)	-	0	-
Annex Y-3(Resistance to corrosion)	-	0	-
Annex Y-4(Gaskets)	-	0	-
Annex Y-5(Protection of equipment within an outdoor enclosure)	-	0	-
Annex Y-6(Mechanical strength of enclosures)	-	0	-
Annex Q-2(Test for external circuits – paired conductor cable)	-	0	-

20 Jun, 2028

-
Included w.e.f 04.06.2026

IS 2167 (2025)

Commercial Beverage Coolers - Specification (ISO 22044 : 2021, MOD) (Fourth Revision)

400000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5.1(Classification According To Temperature)	-	1000	-
Cl.5.2(Construction)	-	2000	-
Cl.6.2.2(Seal Test For Door And Lids)	-	5000	-
Cl.6.2.3(Test On Durability Of Door And Lid)	-	50000	-
Cl.6.2.4(Linear Dimensions, Areas And Volumes)	-	5000	-
Cl.6.3.11.2(Temperature Test)	-	20000	-
Cl.6.3.11.3(Half Load Recovery Test)	-	50000	-
Cl.6.3.11.3.6(Energy Consumption test)	-	50000	-
Cl.6.3.12(Water Vapour Condensation Test)	-	50000	-
Cl.6.3.13(Specific Energy Consumption (SEC))	-	50000	-
Cl.6.3.14 and Annex G(Lighting Test)	-	5000	-
Cl.7(Marking)	-	5000	-
Annex B(Net Volume Calculation)	-	5000	-
Annex C(Equivalent Volume Calculation)	-	5000	-
Annex D(Tda Calculation)	-	5000	-
Annex E(Tests For Absence Of Odour And Taste)	-	30000	-
5.1(Classification according to temperature)	-	0	-
5.2(Construction)	-	0	-
5.2,5.2.1(General)	-	0	-
5.2,5.2.2(Materials)	-	0	Charges covered in Cl 5.2
5.2,5.2.3(Thermal insulation)	-	0	Charges covered in Cl 5.2
5.2,5.2.4(Refrigerating system)	-	0	Charges covered in Cl 5.2
5.2,5.2.5(Electrical components)	-	0	Charges covered in Cl 5.22
6.1(General)	-	2000	-
6.2.1,Aneex E(Absence of odour and taste (not compulsory))	-	0	-
6.2.2(Seal test for doors and lids)	-	0	-
6.2.3(Test on durability of door and lid)	-	0	-
6.2.4(Linear dimensions, areas and volumes)	-	0	-
6.3.2(Test room condition)	-	5000	-
6.3.3(M-can)	-	5000	-
6.3.4(Preparation of test commercial beverage cooler and general test procedures)	-	5000	-
6.3.5(Loading the commercial beverage cooler)	-	10000	-
6.3.6(Running in period)	-	10000	-
6.3.7(Stable conditions)	-	10000	-
6.3.8(Lighting and night-covers)	-	10000	-
6.3.9(Power supply)	-	5000	-
6.3.10(Testing several commercial beverage coolers in the same room)	-	0	-
6.3.11.2(Temperature test)	-	0	-
6.3.11.3(Half reload recovery test)	-	0	-
6.3.11.3.6(Energy consumption test)	-	0	-
6.3.12(Water vapour condensation test)	-	0	-
6.3.13(Calculation of specific energy consumption (SEC))	-	0	-
6.3.14(Lighting test)	-	0	-
7.2(Marking plate)	-	0	-
Annex B(Net volume calculation)	-	0	-
Annex C(Equivalent volume calculation)	-	0	-
Annex D(Total display area (TDA))	-	0	-

20 Jun, 2028

-
Included w.e.f 04.06.2026

IS 18689 (2024)

Household and Similar Electrical Appliances - Safety - Particular Requirements for Commercial Refrigerating Appliances and Ice-Makers with an Incorporated or Remote Refrigerant Unit or Motor-Compressor (IEC 60335-2-89 : 2019, MOD)

250000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	5000	-
8(Protection against access to live parts)	-	5000	-
10(Power input and current)	-	15000	-
10.101(Power input and current)	-	0	Testing Charges covered in Cl.10
11(Heating)	-	20000	-
13.1 &13.2(Leakage current test)	-	5000	-
13.1 &13.3(Electric strength test)	-	5000	-
14(Transient overvoltages)	-	10000	-
15(Moisture resistance)	-	15000	-
15.101,15.102,15.103(Moisture resistance)	-	0	Testing Charges covered in Cl.15
16.1 &16.2(Leakage current test)	-	5000	-
16.1 & 16.3(Electric strength test)	-	5000	-
17(Overload protection of transformers and associated circuits)	-	10000	-
19(Abnormal operation)	-	30000	Testing Charges Rs. 30000 /- is for Cl. 19 (Excluding EMI/EMC Tests of Cl.19.11.4.1 to Cl.19.11.4.7). If applicable, the testing charges Rs. 89000/- for EMI/EMC tests will be charged extra for the respective EMI/EMC tests.
19.101(Abnormal operation)	-	0	Testing charges covered in Cl.19
19.102(Abnormal operation)	-	0	Testing charges covered in Cl.19
19.103(Abnormal operation)	-	0	Testing charges covered in Cl.19
20(Stability and mechanical hazards)	-	10000	-
21(Mechanical strength)	-	10000	-
21.101(Mechanical strength)	-	0	Testing charges covered in Cl.21
21.102(Mechanical strength)	-	0	Testing charges covered in Cl.21
21.103(Mechanical strength)	-	0	Testing charges covered in Cl.21
22(Construction)	-	40000	-
23(Internal wiring)	-	5000	-
24(Components)	-	5000	-
25("Supply connection and external flexible cords")	-	5000	-
26("Terminals for external conductors")	-	5000	-
27(Provision for earthing)	-	5000	-
28(Screws and connections)	-	5000	-
29("Clearances, creepage distances and solid insulation")	-	10000	-
30("Resistance to heat and fire ")	-	15000	-
31(Resistance to rusting)	-	5000	-
7(Marking and instructions)	-	0	-
8(Protection against access to live parts)	-	0	-
10(Power input and current)	-	0	-
10.101(Power input and current)	-	0	-
11(Heating)	-	0	-
13.1 &13.2(Leakage current test)	-	0	-
13.1 &13.3(Electric strength test)	-	0	-
14(Transient overvoltages)	-	0	-
15(Moisture resistance)	-	0	-
15.101,15.102,15.103(Moisture resistance)	-	0	-
16.1 &16.2(Leakage current test)	-	0	-
16.1 & 16.3(Electric strength test)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
19(Abnormal operation)	-	0	-
19.101(Abnormal operation)	-	0	-
19.102(Abnormal operation)	-	0	-
19.103(Abnormal operation)	-	0	-
20(Stability and mechanical hazards)	-	0	-
21(Mechanical strength)	-	0	-
21.101(Mechanical strength)	-	0	-
21.102(Mechanical strength)	-	0	-
21.103(Mechanical strength)	-	0	-
22(Construction)	-	0	-
23(Internal wiring)	-	0	-
24(Components)	-	0	-
25("Supply connection and external flexible cords")	-	0	-
26("Terminals for external conductors")	-	0	-
27(Provision for earthing)	-	0	-
28(Screws and connections)	-	0	-
29("Clearances, creepage distances and solid insulation")	-	0	-
30("Resistance to heat and fire ")	-	0	-
31(Resistance to rusting)	-	0	-
7(Marking and instructions)	-	0	-
8(Protection against access to live parts)	-	0	-
10(Power input and current)	-	0	-
10.101(Power input and current)	-	0	-
11(Heating)	-	0	-
13.1 &13.2(Leakage current test)	-	0	-
13.1 &13.3(Electric strength test)	-	0	-
14(Transient overvoltages)	-	0	-
15(Moisture resistance)	-	0	-
15.101,15.102,15.103(Moisture resistance)	-	0	-
16.1 &16.2(Leakage current test)	-	0	-
16.1 & 16.3(Electric strength test)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
19(Abnormal operation)	-	0	-
19.101(Abnormal operation)	-	0	-
19.102(Abnormal operation)	-	0	-
19.103(Abnormal operation)	-	0	-
20(Stability and mechanical hazards)	-	0	-
21(Mechanical strength)	-	0	-
21.101(Mechanical strength)	-	0	-
21.102(Mechanical strength)	-	0	-
21.103(Mechanical strength)	-	0	-
22(Construction)	-	0	-
23(Internal wiring)	-	0	-
24(Components)	-	0	-
25("Supply connection and external flexible cords")	-	0	-
26("Terminals for external conductors")	-	0	-
27(Provision for earthing)	-	0	-
28(Screws and connections)	-	0	-
29("Clearances, creepage distances and solid insulation")	-	0	-
30("Resistance to heat and fire ")	-	0	-
31(Resistance to rusting)	-	0	-
7(Marking and instructions)	-	0	-
8(Protection against access to live parts)	-	0	-
10(Power input and current)	-	0	-
10.101(Power input and current)	-	0	-
11(Heating)	-	0	-
13.1 &13.2(Leakage current test)	-	0	-
13.1 &13.3(Electric strength test)	-	0	-
14(Transient overvoltages)	-	0	-
15(Moisture resistance)	-	0	-
15.101,15.102,15.103(Moisture resistance)	-	0	-
16.1 &16.2(Leakage current test)	-	0	-
16.1 & 16.3(Electric strength test)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
19(Abnormal operation)	-	0	-
19.101(Abnormal operation)	-	0	-
19.102(Abnormal operation)	-	0	-
19.103(Abnormal operation)	-	0	-
20(Stability and mechanical hazards)	-	0	-
21(Mechanical strength)	-	0	-
21.101(Mechanical strength)	-	0	-
21.102(Mechanical strength)	-	0	-
21.103(Mechanical strength)	-	0	-
22(Construction)	-	0	-
23(Internal wiring)	-	0	-
24(Components)	-	0	-
25("Supply connection and external flexible cords")	-	0	-
26("Terminals for external conductors")	-	0	-
27(Provision for earthing)	-	0	-
28(Screws and connections)	-	0	-
29("Clearances, creepage distances and solid insulation")	-	0	-
30("Resistance to heat and fire ")	-	0	-
31(Resistance to rusting)	-	0	-

20 Jun, 2028

-
Included w.e.f. 08.04.2026 Exclusion: 22.32 (Construction)

IS 302 : Part 2 : Sec 40 (2025)

Safety of Household and Similar Electrical Appliances Part 2 Particular Requirements Sec 40 Electrical Heat Pumps, Air-Conditioners and Dehumidifiers (IEC 60335-2-40 : 2022, MOD)

300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation, toxicity and similar hazards)	-	5000	-
31(Resistance to rusting)	-	5000	-
30(Resistance to heat and fire)	-	10000	-
29(Clearances, creepage distances and solid insulation)	-	10000	-
28(Screws and connections)	-	5000	-
27(Provision for earthing)	-	5000	-
26(Terminals for external conductors)	-	5000	-
25(Supply connection and external flexible cords)	-	5000	-
24(Components)	-	5000	-
23(Internal wiring)	-	5000	-
22.117(Hot surfaces)	-	0	Testing Charges covered in Cl.22
22.116(Arcs and sparks from electric components)	-	0	Testing Charges covered in Cl.22
22(Construction)	-	35000	-
21(Mechanical strength)	-	10000	-
19.104.8(Back up protection test)	-	30000	Testing Charges for Cl. 19 (Excluding EMI/EMC Tests of Cl.19.11.4.1 to Cl.19.11.4.7) is Rs. 30000/- The testing charges for EMI/EMC tests will be charged extra as applicable as mentioned in the respective clauses..
20(Stability and mechanical hazards)	-	10000	-
19.11.4.7(Mains signals)	-	5000	-
19.11.4.6(Class 3 voltage dips and interruptions)	-	5000	-
19.11.4.5(Injected currents)	-	10000	-
19.11.4.4(Voltage dips and interruptions)	-	5000	-
19.11.4.3(Fast transient bursts)	-	5000	-
19.11.4.2(Radiated fields)	-	20000	-
19.11.4.1(Electrostatic discharges)	-	5000	-
18(Endurance)	-	0	-
17(Overload protection of transformers and associated circuits)	-	10000	-
16(Leakage current and electric strength)	-	10000	-
15.101(Spillage test)	-	0	Testing Charges covered in Cl.15
15(Moisture resistance)	-	15000	-
14(Transient overvoltages)	-	10000	-
13(Leakage current and electric strength at operating temperature)	-	10000	-
12(Void)	-	0	-
11(Heating)	-	20000	-
10(Power input and current)	-	15000	-
8(Protection against access to live parts)	-	5000	-
7(Marking and instructions)	-	5000	-
6(Classification)	-	0	-
5(General conditions for the tests)	-	0	-
4(General requirement)	-	0	-
32(Radiation, toxicity and similar hazards)	-	0	-
31(Resistance to rusting)	-	0	-
30(Resistance to heat and fire)	-	0	-
29(Clearances, creepage distances and solid insulation)	-	0	-
28(Screws and connections)	-	0	-
27(Provision for earthing)	-	0	-
26(Terminals for external conductors)	-	0	-
25(Supply connection and external flexible cords)	-	0	-
24(Components)	-	0	-
23(Internal wiring)	-	0	-
22.117(Hot surfaces)	-	0	-
22.116(Arcs and sparks from electric components)	-	0	-
22(Construction)	-	0	-
21(Mechanical strength)	-	0	-
19.104.8(Back up protection test)	-	0	-
20(Stability and mechanical hazards)	-	0	-
19.11.4.7(Mains signals)	-	0	-
19.11.4.6(Class 3 voltage dips and interruptions)	-	0	-
19.11.4.5(Injected currents)	-	0	-
19.11.4.4(Voltage dips and interruptions)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
18(Endurance)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
16(Leakage current and electric strength)	-	0	-
15.101(Spillage test)	-	0	-
15(Moisture resistance)	-	0	-
14(Transient overvoltages)	-	0	-
13(Leakage current and electric strength at operating temperature)	-	0	-
12(Void)	-	0	-
11(Heating)	-	0	-
10(Power input and current)	-	0	-
8(Protection against access to live parts)	-	0	-
7(Marking and instructions)	-	0	-
6(Classification)	-	0	-
5(General conditions for the tests)	-	0	-
4(General requirement)	-	0	-

20 Jun, 2028

-
Included w.e.f. 01.04.2026 Exclusion: 32 (Radiation, toxicity and similar hazards), 22 (Construction), 24 (Components)

IS 18112 (2025)

DIGITAL TELEVISION RECEIVER FOR SATELLITE BROADCAST TRANSMISSION SPECIFICATION (First Revision)

428000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.4, Table-2, ii)(RF characteristics to be supported by the DTV receiver)	-	0	-
Clause 4.3(Specifications)	-	50000	Separately covered as per IS 616
Clause 4.5(Safety Requirements)	-	0	-
Clause 4.6(Electromagnetic Compatibility (EMC) Requirements)	-	140000	-
Clause 5(Marking)	-	2000	-
Clause 6(Operating Life Test)	-	10000	-
Clause 4.1, Table-1, i) a)(Hardware specification)	-	3000	-
Clause 4.1, Table-1, i) b)(Decompression and decoding of SDTV video)	-	5000	-
Clause 4.1, Table-1, i) c)(Decompression and decoding of HDTV video)	-	5000	-
Clause 4.1, Table-1, i) d)(Decompression and decoding of audio)	-	5000	-
Clause 4.1, Table-1, i) e)(Active Format descriptors)	-	5000	-
Clause 4.1, Table-1, i) f)(Captioning and Sub-titling)	-	5000	-
Clause 4.1, Table-1, i) g)(Teletext)	-	5000	-
Clause 4.1, Table-1, i) h)(Multi-language support)	-	3000	-
Clause 4.1, Table-1, i) j)(DTV receiver mixed Audio Description)	-	3000	-
Clause 4.1, Table-1, i) k)(Broadcast mixed audio description)	-	3000	-
Clause 4.1, Table-1, i) m)(Service demultiplexing)	-	3000	-
Clause 4.1, Table-1, i) n)(Data services)	-	3000	-
Clause 4.1, Table-1, i) p)(OSD)	-	5000	-
Clause 4.1, Table-1, i) q)(DTV character set)	-	5000	-
Clause 4.1, Table-1, i) r)(Electronic Service Guide (ESG) ‘Now/Next’)	-	5000	-
Clause 4.1, Table-1, i) s)(Time)	-	5000	-
Clause 4.1, Table-1, i) t)(Digital TV output)	-	5000	-
Clause 4.4, Table-2, i) b)(Frequency)	-	5000	-
Clause 4.4, Table-2, i) a)(Input voltage range)	-	5000	-
Clause 4.1,Table-1, ii) a)(Demodulation and FEC decoding)	-	5000	-
Clause 4.1, Table-1, ii) b)(DTV Receiver Installation)	-	5000	-
Clause 4.1, Table-1, ii) c)(Network evolution)	-	5000	-
Clause 4.4, Table-2, iii) c)(RF input impedance)	-	0	-
Clause 4.1, Table-1, ii) d)(Services available)	-	5000	-
Clause 4.1, Table-1, ii) e)(Selection via Service List)	-	5000	-
Clause 4.1, Table-1, ii) f)(Selection via Numeric Entry)	-	5000	-
Clause 4.1, Table-1, ii) g)(Favourite Channel list)	-	5000	-
Clause 4.1, Table-1, ii) h)(Hidden Services)	-	5000	-
Clause 4.4, Table-2, iii) b)(Input frequency range)	-	5000	-
Clause 4.1, Table-1, ii) j)(Logical Channel Number for Satellite services)	-	5000	-
Clause 4.1, Table-1, ii) k)(RF input signal)	-	10000	-
Clause 4.1, Table-1, ii) m)(LNB supply current)	-	5000	-
Clause 4.1, Table-1, ii) n)(LNB supply voltage)	-	5000	-
Clause 4.1, Table-1, ii) p)(LNB Control)	-	5000	-
Clause 4.1, Table-1, ii) q)(Modulation/Demodulation parameters for DVB-S & DVB-S2 standard)	-	0	-
Clause 4.4, Table-2, iii) a)(Input level per carrier)	-	15000	-
Clause 4.4, Table-2, iv) c)(RF input impedance)	-	0	-
Clause 4.4, Table-2, iv) b)(Input frequency range)	-	5000	-
Clause 4.4, Table-2, iv) a)(Input level per carrier)	-	15000	-
Clause 4.4, Table-2, v)(Symbol rate)	-	5000	-
Clause 4.4, Table-2, vi)(RF input return loss)	-	0	-
Clause 4.4, Table-2, vii)(DisEqC)	-	5000	-
Clause 4.4, Table-2, viii)(Operating ambient temperature range)	-	0	-
Clause 4.4, Table-2, ix)(Operating humidity range)	-	0	-
Clause 4.1, Table-1, iii) a)(Interfaces, Connectors)	-	5000	-
Clause 4.1, Table-1, iv)(Automatic software upgrade mechanism)	-	5000	-
Clause 4.1, Table-1, v) a)(Remote Control)	-	5000	-
Clause 4.1, Table-1, v) b)(Easy to use and simple documentation)	-	5000	-
Clause 3.1, Table-1, v) c)(Support package)	-	3000	-

20 Jun, 2028

-
Included w.e.f. 13.11.2025

IS 17550 : Part 3 (2025)

Household Refrigerating Appliances - Characteristics and Methods Of Test Part 3 Energy Consumption and Volume (First Revision)

160000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1, Annex A(set up for energy consumption)	-	0	-
Clause 4.2, Annex B(Steady state power consumption)	-	0	-
Clause 4.3, Annex C(Defrost and Recovery Energy and Temperature Change)	-	0	-
Clause 4.4, Annex D(Defrost Frequency)	-	0	-
Clause 4.5, Annex E(Number of Test Points and Interpolation)	-	0	-
Clause 4.6, Annex G(Load Processing Efficiency)	-	0	-
Clause 4.7, Annex F(Specified Auxiliaries)	-	0	-
Clause 4.8, Annex H(Volume determination)	-	10000	-
Clause 4.8.1, Annex H(Rated total volume)	-	0	-
Clause 5, 5.1, 5.2 Table 1(TARGET TEMPERATURES FOR ENERGY DETERMINATION)	-	0	-
Clause 6, 6.1 to 6.8(DETERMINATION OF ENERGY CONSUMPTION)	-	150000	-
Clause 4.1, Annex A(set up for energy consumption)	-	0	-
Clause 4.2, Annex B(Steady state power consumption)	-	0	-
Clause 4.3, Annex C(Defrost and Recovery Energy and Temperature Change)	-	0	-
Clause 4.4, Annex D(Defrost Frequency)	-	0	-
Clause 4.5, Annex E(Number of Test Points and Interpolation)	-	0	-
Clause 4.6, Annex G(Load Processing Efficiency)	-	0	-
Clause 4.7, Annex F(Specified Auxiliaries)	-	0	-
Clause 4.8, Annex H(Volume determination)	-	0	-
Clause 4.8.1, Annex H(Rated total volume)	-	0	-
Clause 5, 5.1, 5.2 Table 1(TARGET TEMPERATURES FOR ENERGY DETERMINATION)	-	0	-
Clause 6, 6.1 to 6.8(DETERMINATION OF ENERGY CONSUMPTION)	-	0	-

20 Jun, 2028

-
Included w.e.f 18.11.2025

IS 13340 : PART 1 (2024)

Shunt Power Capacitors of the Self-Healing Type for a.c. Systems Having a Rated Voltage up to and Including 1 000 V Part 1 General - Performance, Testing and Rating - Safety Requirements - Guide for Installation and Operation (Second Revision)

upto 50kVAr

249650.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Capacitance measurement and output calculation)	-	24000.00	-
8(Measurement of the tangent of the loss angle (tan δ) of the capacitor)	-	11000.00	-
9(Voltage tests between terminals)	-	3000.00	-
10(Voltage tests between terminals and container)	-	3000.00	-
11(Voltage tests between terminals and container)	-	5500.00	-
12(Sealing test)	-	11000.00	-
13(Thermal stability test)	-	24000.00	-
14("Measurement of the tangent of the loss angle (tan δ) of the capacitor at elevated temperature")	-	24000.00	-
7(Capacitance measurement and output calculation)	-	0	-
15(Lightning impulse voltage test between terminals and container)	-	10000.00	-
16(Discharge test)	-	12000.00	-
17(Ageing test)	-	51150.00	-
18(Self-healing test)	-	11000.00	-
19(Destruction test)	-	31000.00	-
20(Maximum permissible voltage)	-	8000.00	-
20.1(Long-duration voltages)	-	0	-
20.2(Long-duration voltages)	-	0	-
21(Maximum permissible current)	-	8000.00	-
22(Discharge device)	-	5500.00	-
23("Container connections ")	-	5000.00	-
24(Protection of the environment)	-	0	-
25(Other safety requirements)	-	0	-
26(Marking of the unit)	-	1250.00	-
26.1(Rating plate)	-	0	-
26.2(Standardized connection symbols)	-	0	-
26.3(Warning plate)	-	0	-
27(Marking of the bank)	-	1250.00	-
27.1(Instruction sheet or rating plate)	-	0	-
27.2(Warning plate)	-	0	-
28(General)	-	0	-
29(9 Choice of the rated voltage)	-	0	-
30(Operating temperature)	-	0	-
31(Special service conditions)	-	0	-
32(2 Overvoltages)	-	0	-
33(Overload currents)	-	0	-
34(Switching and protective devices and connections)	-	0	-
36(Capacitors connected to systems with audio-frequency remote control)	-	0	-
36(Capacitors connected to systems with audio-frequency remote control)	-	0	-
37(Electromagnetic compatibility (EMC))	-	0	-
7(Capacitance measurement and output calculation)	-	0	-
8(Measurement of the tangent of the loss angle (tan δ) of the capacitor)	-	0	-
9(Voltage tests between terminals)	-	0	-
10(Voltage tests between terminals and container)	-	0	-
11(Voltage tests between terminals and container)	-	0	-
12(Sealing test)	-	0	-
13(Thermal stability test)	-	0	-
14("Measurement of the tangent of the loss angle (tan δ) of the capacitor at elevated temperature")	-	0	-
7(Capacitance measurement and output calculation)	-	0	-
15(Lightning impulse voltage test between terminals and container)	-	0	-
16(Discharge test)	-	0	-
17(Ageing test)	-	0	-
18(Self-healing test)	-	0	-
19(Destruction test)	-	0	-
20(Maximum permissible voltage)	-	0	-
20.1(Long-duration voltages)	-	0	-
20.2(Long-duration voltages)	-	0	-
21(Maximum permissible current)	-	0	-
22(Discharge device)	-	0	-
23("Container connections ")	-	0	-
24(Protection of the environment)	-	0	-
25(Other safety requirements)	-	0	-
26(Marking of the unit)	-	0	-
26.1(Rating plate)	-	0	-
26.2(Standardized connection symbols)	-	0	-
26.3(Warning plate)	-	0	-
27(Marking of the bank)	-	0	-
27.1(Instruction sheet or rating plate)	-	0	-
27.2(Warning plate)	-	0	-
28(General)	-	0	-
29(9 Choice of the rated voltage)	-	0	-
30(Operating temperature)	-	0	-
31(Special service conditions)	-	0	-
32(2 Overvoltages)	-	0	-
33(Overload currents)	-	0	-
34(Switching and protective devices and connections)	-	0	-
36(Capacitors connected to systems with audio-frequency remote control)	-	0	-
36(Capacitors connected to systems with audio-frequency remote control)	-	0	-
37(Electromagnetic compatibility (EMC))	-	0	-

20 Jun, 2028

-
Included w.e.f. 04.08.2025

IS 302 : Part 2 : SEC 31 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 31 range hoods

54000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	0	-
Clause No - 5.18(linear and angular dimension)	-	0	-
Clause No - 6.2(harmfull ingress of water)	-	0	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	2000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	0	Testing charges included in Clause No - 8.1.1
Clause No - 8.2(Addition)	-	0	Testing charges included in Clause No - 8.1.1
Clause No - 10.1, Table No. -1(power input deviation)	-	2000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	1500	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	1500	-
Clause No - 14(Impulse test voltage)	-	2000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	0	Testing charges included in Clause No - 15
Clause No -19.7(test is repeated with the capacitor short circuited)	-	6000	-
Clause No -19.11.4.1(electrostatic discharge)	-	5000	if applicable (The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be Rs. 55000 charged extra)
Clause No -19.11.4.2(radiated field)	-	20000	if applicable
Clause No -19.11.4.3(fast transient)	-	5000	if applicable
Clause No -19.11.4.4(Voltage dips and interruption)	-	5000	if applicable
Clause No -21.1(Mechanical strength)	-	3000	-
Clause No -22.1(construction)	-	0	Testing charges included in Clause No - 22
Clause No -22.11(push force applied)	-	0	Testing charges included in Clause No - 22
Clause No -24.1.2(safety isolating transformer)	-	0	Testing charges included in Clause No - 24
Clause No -24.1.3(for switches)	-	0	Testing charges included in Clause No - 24
Clause No -24.1.4(for automatic control)	-	0	Testing charges included in Clause No - 24
Clause No -24.1.5(for innterconnection couplers)	-	0	Testing charges included in Clause No - 24
Clause No -24.4(plug and socket)	-	0	Testing charges included in Clause No - 24
Clause No -25.8, Table no -11(conductor resistance)	-	1000	-
Clause No -25.5(dimension for pins)	-	0	Testing charges included in Clause No - 25.8
Clause No -27.6(for circuit board)	-	2000	-
Clause No -29.2(comparative tracking index)	-	2000	-
Clause No -29.3.3(dry heat test)	-	0	Testing charges included in Clause No - 29.2
Clause No -30.2.1(glow wire test)	-	3000	-
Clause No -30.101("incorporate combustible material")	-	0	Testing charges included in Clause No - 30.2.1
15(MOISTURE RESISTANCE)	-	4000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	3000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	5000	-
18(ENDURANCE)	-	0	-
28(SCREWS AND CONNECTIONS)	-	1000	-
31(RESISTANCE TO RUSTING)	-	1000	-
19.11.4.5(Immunity to conducted discharges)	-	10000	if applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	if applicable
19.11.4.7(Harmonics)	-	5000	if applicable
22(CONSTRUCTION)	-	5000	-
24(COMPONENTS)	-	3000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	0	-
11(Heating)	-	4000	-
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	0	-
Clause No - 5.18(linear and angular dimension)	-	0	-
Clause No - 6.2(harmfull ingress of water)	-	0	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	0	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	0	-
Clause No - 8.2(Addition)	-	0	-
Clause No - 10.1, Table No. -1(power input deviation)	-	0	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	0	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	0	-
Clause No - 14(Impulse test voltage)	-	0	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	0	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	0	-
Clause No -19.11.4.1(electrostatic discharge)	-	0	-
Clause No -19.11.4.2(radiated field)	-	0	-
Clause No -19.11.4.3(fast transient)	-	0	-
Clause No -19.11.4.4(Voltage dips and interruption)	-	0	-
Clause No -21.1(Mechanical strength)	-	0	-
Clause No -22.1(construction)	-	0	-
Clause No -22.11(push force applied)	-	0	-
Clause No -24.1.2(safety isolating transformer)	-	0	-
Clause No -24.1.3(for switches)	-	0	-
Clause No -24.1.4(for automatic control)	-	0	-
Clause No -24.1.5(for innterconnection couplers)	-	0	-
Clause No -24.4(plug and socket)	-	0	-
Clause No -25.8, Table no -11(conductor resistance)	-	0	-
Clause No -25.5(dimension for pins)	-	0	-
Clause No -27.6(for circuit board)	-	0	-
Clause No -29.2(comparative tracking index)	-	0	-
Clause No -29.3.3(dry heat test)	-	0	-
Clause No -30.2.1(glow wire test)	-	0	-
Clause No -30.101("incorporate combustible material")	-	0	-
15(MOISTURE RESISTANCE)	-	0	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	0	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	0	-
18(ENDURANCE)	-	0	-
28(SCREWS AND CONNECTIONS)	-	0	-
31(RESISTANCE TO RUSTING)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
22(CONSTRUCTION)	-	0	-
24(COMPONENTS)	-	0	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	0	-
11(Heating)	-	0	-

20 Jun, 2028

-
Included w.e.f 28.07.2025 Exclusion: Cl 22.32 (Construction) Rubber parts oxygen bomb test, Cl 24 (Components) Components testing

IS 4250 (2025)

Electric Food-Mixers (Liquidizers and Grinders) and Centrifugal Juicers ï¿½ Specification ( Second Revision )

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirements)	-	0	-
Cl-5(General Conditions for the tests)	-	0	-
Cl-6(Classification)	-	0	-
Cl-7(Marking)	-	1000	-
Cl-8(Safety Requirements)	-	20000	-
Cl-9(Endurance fpr motor and base assembly)	-	10000	-
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	2000	-
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	1000	-
Cl-10.4(Idli Batter)	-	1000	-
Cl-10.5(Operational Tests for Juicers)	-	2000	-
Cl-11(Temperature Withstand Test for Bowl)	-	1000	-
Cl-12.1(Test for Switches)	-	1000	-
Cl-13(Strength of Assembly)	-	1000	-
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	1000	-
Cl-14.2, Table-2 (ii)(Power input and current)	-	2000	-
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	1000	-
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	1000	-
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	1000	-
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	1000	-
Cl-19.11.4.1(Electrostatic discharges)	-	5000	if applicable (If EMI/EMC (Cl.19.11.4.1 to Cl.19.11.4.7) testing is applicable then Rs. 55000 will be charged extra)
Cl-19.11.4.2(Radiated fields)	-	20000	if applicable
Cl-19.11.4.3(Fast transient bursts)	-	5000	if applicable
Cl-19.11.4.4(Surge immunity test)	-	5000	if applicable
Cl-19.11.4.5(Immunity to conducted discharges)	-	10000	if applicable
Cl-19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	if applicable
Cl-19.11.4.7(Harmonics)	-	5000	if applicable

20 Jun, 2028

-
Included w.e.f 28.07.2025 Exclusion: Cl 22.32 (Construction) Rubber parts oxygen bomb test, Cl 24 (Components) Components testing

IS 17980 (2022)

Maximum Power Point Tracking Efficiency of Grid Connected Photovoltaic Inverters (First Revision)

Upto 150kW

550000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (a)(Static MPPT efficiency)	-	250000		-
Cl-4.1 (b)(Dynamic MPPT efficiency)	-	300000		-

20 Jun, 2028

-
Included w.e.f.28.04.2025

IS/IEC 61683 (1999)

Photovoltaic systems - Power conditioners - Procedure for measuring efficiency

Upto 150kW

120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Efficiency calculations)	-	50000	-
6(Efficiency test circuits)	-	50000	-
7(Loss measurement)	-	20000	-
Annex A(Power conditioner description)	-	0	-
Annex B(Power efficiency and conversion factor)	-	0	-
Annex C(Weighted average energy efficiency)	-	0	-
Annex D(Derivation of efficiency tolerance in Table 2)	-	0	-
4(Efficiency measurement conditions)	-	0	-
4.1(DC power source for testing)	-	0	-
4.2(Temperature)	-	0	-
4.3(Output voltage and frequency)	-	0	-
4.4(Input voltage)	-	0	-
4.5(Ripple and distortion)	-	0	-
4.6(Resistive loads/utility grid)	-	0	-
4.7(Reactive loads)	-	0	-
4.8(Resistive plus non-linear loads)	-	0	-
4.9(Complex loads)	-	0	-

20 Jun, 2028

-
Included w.e.f.28.04.2025

IS 18112 (2022)

Digital Television Receiver for Satellite Broadcast Transmission Specification

115000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4(Marking)	-	5000		-
3.6(Electromagnetic Compatibility (EMC) Requirements)	-	110000		Charges for Radiated and Conducted Emission test

20 Jun, 2028

-
Included w.e.f.28.04.2025 Only for Cl. 3.6 EMC requirements

IS 302 : Part 2 : Sec 14 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 14 electric kitchen machines (First Revision)

69700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Classification- IS 302-1 )	-	0	-
7.1(Marking- IS 302-1)	-	2000	Testing charges are for Cl. no.7.
7.3(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.4(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.6(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.7(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.8(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.11(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.12(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.13(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.14(Marking- IS 302-1)	-	0	Testing charges are included in Cl. 7.1
7.101(Marking)	-	0	Testing charges are included in Cl. 7.1
8( Protection Against Electric Shock, IS 302-1)	-	2000	-
10(Power Input and Current, IS 302-1)	-	2000	-
11(Heating, IS 302-1)	-	4000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	3000	-
14(Transient Over Voltages, IS 302-1)	-	2000	-
15.1(Moisture Resistance, IS 302-1)	-	4000	Testing clauses are for Cl. no. 15
15.2(Moisture Resistance, IS 302-1)	-	0	Testing clauses are included in Cl. no. 15.1
15(Moisture Resistance, IS 302-1)	-	0	Testing clauses are included in Cl. no. 15.1
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	3000	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	5000	-
19.1(Abnormal Operation, IS 302-1)	-	6000	Testing charges are for Cl. no.19
19.101(Abnormal Operation)	-	0	Testing charges are included in Cl. 19.1
19.102(Abnormal Operation)	-	0	Testing charges are included in Cl. 19.1
19.7(Abnormal Operation, IS 302-1)	-	0	Testing charges are included in Cl. 19.1
19.8(Abnormal Operation, IS 302-1)	-	0	Testing charges are included in Cl. 19.1
19.9(Abnormal Operation, IS 302-1)	-	0	Testing charges are included in Cl. 19.1
20.1(Stability & Mechanical Hazards, IS 302-1)	-	2000	Testing charges are for Cl. 20
20.2(Stability & Mechanical Hazards, IS 302-1)	-	0	Testing charges are included in Cl. 20.1
20.101(Stability & Mechanical Hazards)	-	0	Testing charges are included in Cl. 20.1
20.102(Stability & Mechanical Hazards)	-	0	Testing charges are included in Cl. 20.1
20.103(Stability & Mechanical Hazards)	-	0	Testing charges are included in Cl. 20.1
20.104(Stability & Mechanical Hazards)	-	0	Testing charges are included in Cl. 20.1
21.1(Mechanical Strength, IS 302-1)	-	2000	Testing Charges are for Cl. 21
21.2(Mechanical Strength, IS 302-1)	-	0	Testing charges are included in Cl. 21.1
22(Construction, IS 302-1)	-	3000	Testing charges are for Cl. 22
22.101(Construction)	-	0	Testing charges are included in Cl. 22.1
22.102(Construction)	-	0	Testing charges are included in Cl. 22.1
23.1(Internal Wiring, IS 302-1)	-	2000	Testing charges are for Cl. 23
23.2(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
23.3(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
23.4(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
23.5(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
23.6(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
23.7(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
23.8(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
23.9(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
23.10(Internal Wiring, IS 302-1)	-	0	Testing charges are included in Cl. 23.1
24.1(Components, IS 302-1)	-	3000	Testing charges are for Cl. 24
24.2(Components, IS 302-1)	-	0	Testing charges are included in Cl. 24.1
24.5(Components, IS 302-1)	-	0	Testing charges are included in Cl. 24.1
24.6(Components, IS 302-1)	-	0	Testing charges are included in Cl. 24.1
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	6000	Testing charges are for Cl. 25
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 26.1
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges are included in Cl. 25.1
26(Terminals for External Conductors, IS 302-1)	-	1000	-
27(Provision for Earthing, IS 302-1)	-	2000	Testing charges are for Cl. 27
27.2(Provision for Earthing, IS 302-1)	-	0	Testing charges are included in Cl. 27.1
27.3(Provision for Earthing, IS 302-1)	-	0	Testing charges are included in Cl. 27.1
27.4(Provision for Earthing, IS 302-1)	-	0	Testing charges are included in Cl. 27.1
27.5(Provision for Earthing, IS 302-1)	-	0	Testing charges are included in Cl. 27.1
28(Screws & Connections, IS 302-1)	-	1000	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	2000	Testing charges are for Cl. 29
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	0	Testing charges are included in Cl. 29.1
30.1(Resistance to Heat and Fire, IS 302-1)	-	3000	Testing charges are for Cl. 30
30.2(Resistance to Heat and Fire, IS 302-1)	-	0	Testing charges are included in Cl. 30.1
31(Resistance of Rusting, IS 302-1)	-	1000	-
32(Radiation, Toxicity and similar Hazard IS 302-1)	-	1000	-
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	0	-
20.105(Stability & Mechanical Hazards)	-	0	-
20.106(Stability & Mechanical Hazards)	-	0	-
20.107(Stability & Mechanical Hazards)	-	0	-
20.108(Stability & Mechanical Hazards)	-	0	-
20.109(Stability & Mechanical Hazards)	-	0	-
20.110(Stability & Mechanical Hazards)	-	0	-
20.111(Stability & Mechanical Hazards)	-	0	-
20.112(Stability & Mechanical Hazards)	-	0	-
20.113(Stability & Mechanical Hazards)	-	0	-
20.114(Stability & Mechanical Hazards)	-	0	-
20.115(Stability & Mechanical Hazards)	-	0	-
20.116(Stability & Mechanical Hazards)	-	0	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	0	-
19.11.4.1(Electrostatic discharges)	-	5000	If applicable
19.11.4.2(Radiated fields)	-	20000	If applicable
19.11.4.3(Fast transient bursts)	-	5000	If applicable
19.11.4.4(Surge immunity test)	-	5000	If applicable
19.11.4.5(Immunity to conducted discharges)	-	10000	If applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	If applicable
19.11.4.7(Harmonics)	-	5000	If applicable

20 Jun, 2028

-
-

IS 302 : Part 2 : Sec 26 (2014)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 26 clocks (First Revision)

105000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Classification)	-	0	-
7(Marking and instructions)	-	1000	-
8(Protection against live parts)	-	2000	-
10(POWER INPUT AND CURRENT)	-	0	-
11(HEATING)	-	4000	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	3000	-
14(TRANSIENT OVERVOLTAGES)	-	1000	-
15(MOISTURE RESISTANCE)	-	4000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	3000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	0	-
19(ABNORMAL OPERATION)	-	3000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	2000	-
21(MECHANICAL STRENGTH)	-	2000	-
22(CONSTRUCTION)	-	2000	-
23(INTERNAL WIRING)	-	2000	-
24(COMPONENTS)	-	3000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	2000	-
27(PROVISION FOR EARTHING)	-	2000	-
28(SCREWS AND CONNECTIONS)	-	2000	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
30(RESISTANCE TO HEAT AND FIRE)	-	4000	-
31(RESISTANCE TO RUSTING)	-	1000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	1000	-
19.11.4.1(Electrostatic discharges)	-	5000	If applicable
19.11.4.2(Radiated fields)	-	20000	If applicable
19.11.4.3(Fast transient bursts)	-	5000	If applicable
19.11.4.4(Surge immunity test)	-	5000	If applicable
19.11.4.5(Immunity to conducted discharges)	-	10000	If applicable
19.11.4.6(Voltage dips and interruptions)	-	5000	If applicable
19.11.4.7(Harmonics)	-	5000	If applicable

20 Jun, 2028

-
-

IS 302 : Part 2 : Sec 15 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 15 appliances for heating liquids (First Revision)

71237 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Classification)	-	0	-
7(Marking and instructions)	-	2000	-
8(Protection against live parts)	-	2000	-
10(POWER INPUT AND CURRENT)	-	2000	-
11(HEATING)	-	4000	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	3000	-
14(TRANSIENT OVERVOLTAGES)	-	2000	-
15(MOISTURE RESISTANCE)	-	3000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	3000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	5000	-
19(ABNORMAL OPERATION)	-	6000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be charged extra.
20(STABILITY AND MECHANICAL HAZARDS)	-	2000	-
21(MECHANICAL STRENGTH)	-	2000	-
22(CONSTRUCTION)	-	5000	-
23(INTERNAL WIRING)	-	2000	-
24(COMPONENTS)	-	3000	Above charges applicable excluding the test of clauses mentioned in the list of exclusions.
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	2000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	1000	-
27(PROVISION FOR EARTHING)	-	2000	-
28(SCREWS AND CONNECTIONS)	-	1000	-
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
30(RESISTANCE TO HEAT AND FIRE)	-	3000	-
31(RESISTANCE TO RUSTING)	-	1000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	1000	-
19.11.4.1(Electrostatic discharges)	-	5000	--
19.11.4.2(Radiated fields)	-	20000	--
19.11.4.3(Fast transient bursts)	-	5000	--
19.11.4.4(Surge immunity test)	-	5000	--
19.11.4.5(Immunity to conducted discharges)	-	10000	--
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	--
19.11.4.7(Harmonics)	-	5000	--

20 Jun, 2028

-
Exclusions: Cord Reel Test (Cl. 22.16), Oxygen bomb test for rubber material (Cl. 22.32), Software (Cl. 22.46), Capacitor Test (Cl. 24.1.1), Switching Cycle Operation Test (Cl. 24.1.3), Automatic Control Cycle Operation Test (Cl. 24.1.4), Appliance Coupler and Interconnection Coupler Test (Cl. 24.1.5), Lamp Holder Test (Cl. 24.1.6), Capacitor in Auxiliary Winding of Motor Test (Cl. 24.5), Motors Basic Insulation Test (Cl. 24.6)

IS 302 : Part 2 : Sec 35 (2017)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 35 electric instantaneous water heaters (Second Revision)

71612 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 IS 302-2-35(Classification)	-	0	-
Cl. 7 IS 302-2-35(Marking and Instruction)	-	1000	-
Cl. 8 IS 302-2-35(Protection against access to live parts)	-	2000	-
Cl. 10 IS 302-2-35(Power Input and Current )	-	3000	-
Cl. 11 IS 302-2-35(Heating)	-	5000	-
Cl. 13 IS 302-2-35(Leakage Current & Electric Strength at Operating Temperature)	-	4000	-
Cl. 14 IS 302-2-35(Radio and television interference suppression / Transient over voltages)	-	2000	-
Cl. 15 IS 302-2-35(Moisture Resistance Test )	-	5000	-
Cl. 16 IS 302-2-35(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	4000	-
Cl. 17 IS 302-2-35(Overload Protection of Transformers and Associated Circuit)	-	2000	-
Cl. 19 IS 302-2-35(Abnormal Operation )	-	5000	-
Cl. 20 IS 302-2-35(Stability & Mechanical Hazards)	-	2000	-
Cl. 21 IS 302-2-35(Mechanical strength)	-	2000	-
Cl. 22 IS 302-2-35(Construction )	-	3000	-
Cl. 23 IS 302-2-35(Internal Wiring)	-	1000	-
Cl. 24 IS 302-2-35(Components)	-	2000	-
Cl. 25 IS 302-2-35(Supply Connection & External Flexible Cords)	-	2000	-
Cl. 26 IS 302-2-35(Terminals for External conductors )	-	1000	-
Cl. 27 IS 302-2-35(Provision for Earthing )	-	3000	-
Cl. 28 IS 302-2-35(Screws & Connections)	-	1000	-
Cl. 29 IS 302-2-35(Clearances, Creepage Distances & Solid insulation )	-	2000	-
Cl. 30 IS 302-2-35(Resistance to Heat Fire & Tracking )	-	4000	-
Cl. 31 IS 302-2-35(Resistance to Rusting)	-	1000	-
Cl. 32 IS 302-2-35(Radiation, Toxicity and similar hazards)	-	1000	-
19.11.4.1(Electrostatic discharges)	-	5000	if applicable
19.11.4.2(Radiated fields)	-	20000	if applicable
19.11.4.3(Fast transient bursts)	-	5000	if applicable
19.11.4.4(Surge immunity test)	-	5000	if applicable
19.11.4.5(Immunity to conducted discharges)	-	10000	if applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	if applicable
19.11.4.7(Harmonics)	-	5000	if applicable

20 Jun, 2028

-
-

IS 302 : Part 2 : Sec 6 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 6 cooking ranges, hobs, ovens and similar appliances (First Revision)

60000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Classification)	-	0	-
7.0(Marking and instructions)	-	2000	-
8.0(Protection against access to live part test)	-	2000	-
9.0(Starting of motor-operated appliances test)	-	0	-
10.0(Power Input and current test)	-	2000	-
11.0(Heating test)	-	4000	-
13.0(Leakage current and electric strength test)	-	3000	-
14.0(Transient voltages)	-	2000	-
15.0(Moisture Resistance)	-	4000	-
16.0(Leakage current and electric strength test)	-	3000	-
17.0(Overload protection of transformers test)	-	5000	-
19.0(Abnormal Operations)	-	6000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be Rs. 55000 charged extra.
20.0(Stability and Mechanical Hazards)	-	2000	-
21.0(Mechanical Strength)	-	3000	-
22.0(Construction verification related tests)	-	5000	-
23.0(Internal wiring)	-	2000	-
24.0(Components)	-	3000	-
25.0(Supply connections and External Flexible Cords)	-	1000	-
26.0(Terminal for External Conductors)	-	1000	-
27.0(Provision for Earthing)	-	2000	-
28.0(Screws and connections)	-	1000	-
29.0(Clearances and Creepage distances and solid insulation)	-	2000	-
30.0(Resistance to heat and fire)	-	3000	-
31.0(Resistance to rusting)	-	1000	-
19.11.4.1(Electrostatic discharges)	-	5000	If applicable
19.11.4.2(Radiated fields)	-	20000	If applicable
19.11.4.3(Fast transient bursts)	-	5000	If applicable
19.11.4.4(Surge immunity test)	-	5000	If applicable
19.11.4.5(Immunity to conducted discharges)	-	10000	If applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	If applicable
19.11.4.7(Harmonics)	-	5000	If applicable
18.0(Endurance test)	-	0	-
4(General Requirements)	-	0	-
5(General condition for the tests)	-	0	-
32.0(Radiation, Toxicity and Similar hazards)	-	1000	-
6.0(Classification)	-	0	-
7.0(Marking and instructions)	-	0	-
8.0(Protection against access to live part test)	-	0	-
9.0(Starting of motor-operated appliances test)	-	0	-
10.0(Power Input and current test)	-	0	-
11.0(Heating test)	-	0	-
13.0(Leakage current and electric strength test)	-	0	-
14.0(Transient voltages)	-	0	-
15.0(Moisture Resistance)	-	0	-
16.0(Leakage current and electric strength test)	-	0	-
17.0(Overload protection of transformers test)	-	0	-
19.0(Abnormal Operations)	-	0	-
20.0(Stability and Mechanical Hazards)	-	0	-
21.0(Mechanical Strength)	-	0	-
22.0(Construction verification related tests)	-	0	-
23.0(Internal wiring)	-	0	-
24.0(Components)	-	0	-
25.0(Supply connections and External Flexible Cords)	-	0	-
26.0(Terminal for External Conductors)	-	0	-
27.0(Provision for Earthing)	-	0	-
28.0(Screws and connections)	-	0	-
29.0(Clearances and Creepage distances and solid insulation)	-	0	-
30.0(Resistance to heat and fire)	-	0	-
31.0(Resistance to rusting)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
18.0(Endurance test)	-	0	-
4(General Requirements)	-	0	-
5(General condition for the tests)	-	0	-
32.0(Radiation, Toxicity and Similar hazards)	-	0	-
6.0(Classification)	-	0	-
7.0(Marking and instructions)	-	0	-
8.0(Protection against access to live part test)	-	0	-
9.0(Starting of motor-operated appliances test)	-	0	-
10.0(Power Input and current test)	-	0	-
11.0(Heating test)	-	0	-
13.0(Leakage current and electric strength test)	-	0	-
14.0(Transient voltages)	-	0	-
15.0(Moisture Resistance)	-	0	-
16.0(Leakage current and electric strength test)	-	0	-
17.0(Overload protection of transformers test)	-	0	-
19.0(Abnormal Operations)	-	0	-
20.0(Stability and Mechanical Hazards)	-	0	-
21.0(Mechanical Strength)	-	0	-
22.0(Construction verification related tests)	-	0	-
23.0(Internal wiring)	-	0	-
24.0(Components)	-	0	-
25.0(Supply connections and External Flexible Cords)	-	0	-
26.0(Terminal for External Conductors)	-	0	-
27.0(Provision for Earthing)	-	0	-
28.0(Screws and connections)	-	0	-
29.0(Clearances and Creepage distances and solid insulation)	-	0	-
30.0(Resistance to heat and fire)	-	0	-
31.0(Resistance to rusting)	-	0	-
19.11.4.1(Electrostatic discharges)	-	0	-
19.11.4.2(Radiated fields)	-	0	-
19.11.4.3(Fast transient bursts)	-	0	-
19.11.4.4(Surge immunity test)	-	0	-
19.11.4.5(Immunity to conducted discharges)	-	0	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	0	-
19.11.4.7(Harmonics)	-	0	-
18.0(Endurance test)	-	0	-
4(General Requirements)	-	0	-
5(General condition for the tests)	-	0	-
32.0(Radiation, Toxicity and Similar hazards)	-	0	-

20 Jun, 2028

-
Included w.e.f.28.04.2025 Exclusion Cl. No. 22.32 Rubber parts test, Cl. No. 22.16 Cord reel test, 24.0 (Components)

IS 302 : Part 2 : Sec 45 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 45 electric heating tools

54000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	0	-
6(Classification)	-	0	-
7(Marking)	-	1000	-
8(Protection against Access to Live Parts)	-	2000	-
9(Starting Of Motor Operated Appliances)	-	0	-
10("Power Input & Current")	-	2000	-
11(Temperature Rise/ Heating)	-	4000	-
12(Operation Under Overload Condition)	-	0	-
13(Electric Insulation at Operating Temperature)	-	3000	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	2000	-
15(Moisture Resistance)	-	4000	-
16(Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength (After Humidity Treatment))	-	3000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	4000	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	4000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be Rs. 55000 charged extra.
20(Stability & Mechanical Hazards)	-	2000	-
21(Mechanical strength)	-	2000	-
22(Construction)	-	5000	-
23(Internal Wiring)	-	2000	-
24(Components)	-	2000	-
25(Supply Connection & External Flexible Cords)	-	2000	-
26(Terminals For External Conductors)	-	1000	-
27(Provision For Earthing)	-	2000	-
28(Screws & Connections)	-	1000	-
29(Creepage Distances & Clearances)	-	2000	-
30(Resistance to Heat, Fire and Tracking)	-	3000	-
31(Radiation hazards)	-	0	Testing charges included in Cl.XXV of Table 101 (Resistance to Rusting)
XXV of Table 101(Resistance to Rusting)	-	1000	-
4(General Requirement)	-	0	-
19.11.4.7(Harmonics)	-	5000	if applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	if applicable
19.11.4.5(Immunity to conducted discharges)	-	10000	if applicable
19.11.4.4(Surge immunity test)	-	5000	if applicable
19.11.4.3(Fast transient bursts)	-	5000	if applicable
19.11.4.2(Radiated fields)	-	20000	if applicable
19.11.4.1(Electrostatic discharges)	-	5000	if applicable

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion Cl 24 (Components)

IS 302 : Part 2 : Sec 12 (1993)

Safety of household and similar electrical appliances - Specification: Part 2 particular requirements: Sec 12 warming plates and similar appliances

56000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	0	-
6(Classification)	-	0	-
7(Marking)	-	1000	-
8(Protection against Access to Live Parts)	-	2000	-
9(Starting Of Motor Operated Appliances)	-	0	-
10("Power Input & Current")	-	2000	-
11(Temperature Rise/ Heating)	-	4000	-
12(Operation Under Overload Conditions of Appliances with heating Element)	-	0	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	3000	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	2000	-
15(Moisture Resistance)	-	4000	-
16(Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength)	-	3000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	4000	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	5000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be Rs. 55000 charged extra.
20(Stability & Mechanical Hazards)	-	2000	-
21(Mechanical strength)	-	2000	-
22(Construction)	-	5000	-
23(Internal Wiring)	-	2000	-
24(Components)	-	3000	-
25(Supply Connection & External Flexible Cords)	-	2000	-
26(Terminals For External Conductors)	-	1000	-
27(Provision For Earthing)	-	2000	-
28(Screws & Connections)	-	1000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	2000	-
30(Resistance to Heat & Fire)	-	3000	-
31(Resistance to Rusting)	-	1000	-
32(Radiation hazards)	-	0	-
5(Rating)	-	0	-
6(Classification)	-	0	-
7(Marking)	-	0	-
8(Protection against Access to Live Parts)	-	0	-
9(Starting Of Motor Operated Appliances)	-	0	-
10("Power Input & Current")	-	0	-
11(Temperature Rise/ Heating)	-	0	-
12(Operation Under Overload Conditions of Appliances with heating Element)	-	0	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	0	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	0	-
15(Moisture Resistance)	-	0	-
16(Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength)	-	0	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	0	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	0	-
20(Stability & Mechanical Hazards)	-	0	-
21(Mechanical strength)	-	0	-
22(Construction)	-	0	-
23(Internal Wiring)	-	0	-
24(Components)	-	0	-
25(Supply Connection & External Flexible Cords)	-	0	-
26(Terminals For External Conductors)	-	0	-
27(Provision For Earthing)	-	0	-
28(Screws & Connections)	-	0	-
29(Clearances, Creepage Distances & Solid Insulation)	-	0	-
30(Resistance to Heat & Fire)	-	0	-
31(Resistance to Rusting)	-	0	-
32(Radiation hazards)	-	0	-
19.11.4.1(Electrostatic discharges)	-	5000	If applicable
19.11.4.2(Radiated fields)	-	20000	If applicable
19.11.4.3(Fast transient bursts)	-	5000	If applicable
19.11.4.4(Surge immunity test)	-	5000	If applicable
19.11.4.5(Immunity to conducted discharges)	-	10000	If applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	5000	If applicable
19.11.4.7(Harmonics)	-	5000	If applicable

20 Jun, 2028

-
Included w.e.f.20.05.2025 Exclusion Cl. No. 22.32 Rubber parts test 24 (Components)

IS 302 : Part 2 : Sec 74 (2024)

Household and Similar Electrical Appliancesï¿½Safety Part 2 Particular Requirements Section 74 Portable immersion heaters

66000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
10(Power input and current)	-	0	Testing charges included in Cl.10
11(Heating)	-	4000	-
13.1 &13.2(Leakage current test)	-	1500	-
13.1 &13.3(Electric strength test)	-	1500	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	4000	-
15.3(Moisture resistance)	-	0	Testing charges included in Cl.15
16.1 &16.2(Leakage current test)	-	1500	-
16.1 & 16.3(Electric strength test)	-	1500	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	8000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be Rs. 55000 charged extra.
20.1(Stability and mechanical hazards)	-	2000	-
20.2(Stability and mechanical hazards)	-	0	Testing charges included in Cl.20.1
21(Mechanical strength)	-	3000	-
22(Construction)	-	8000	-
23(Internal wiring)	-	2000	-
24(Components)	-	3000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	3000	-
30.101(Resistance to heat and fire)	-	0	Testing charges included in Cl.30
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-
Cl 19.11.4.1(Electrostatic discharges)	-	5000	if applicable
Cl 19.11.4.2(Radiated fields)	-	20000	if applicable
Cl 19.11.4.3(Fast transient bursts)	-	5000	if applicable
Cl 19.11.4.4(Voltage surges)	-	5000	if applicable
Cl 19.11.4.5(Immunity to conducted disturbances)	-	10000	if applicable
Cl 19.11.4.6(Voltage dips and interruptions)	-	5000	if applicable
Cl 19.11.4.7(Harmonics and inter-harmonics)	-	5000	if applicable
Cl 19.11.4.8(Abnormal operation)	-	5000	-
24.101(Components)	-	0	Testing charges included in Cl.24
7(Marking and instructions)	-	0	-
8(Protection against access to live parts)	-	0	-
10(Power input and current)	-	0	-
10(Power input and current)	-	0	-
11(Heating)	-	0	-
13.1 &13.2(Leakage current test)	-	0	-
13.1 &13.3(Electric strength test)	-	0	-
14(Transient overvoltages)	-	0	-
15(Moisture resistance)	-	0	-
15.3(Moisture resistance)	-	0	-
16.1 &16.2(Leakage current test)	-	0	-
16.1 & 16.3(Electric strength test)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	0	-
20.1(Stability and mechanical hazards)	-	0	-
20.2(Stability and mechanical hazards)	-	0	-
21(Mechanical strength)	-	0	-
22(Construction)	-	0	-
23(Internal wiring)	-	0	-
24(Components)	-	0	-
25("Supply connection and external flexible cords")	-	0	-
26("Terminals for external conductors")	-	0	-
27(Provision for earthing)	-	0	-
28(Screws and connections)	-	0	-
29("Clearances, creepage distances and solid insulation")	-	0	-
30(Resistance to heat and fire)	-	0	-
30.101(Resistance to heat and fire)	-	0	-
31(Resistance to rusting)	-	0	-
32("Radiation, toxicity and similar hazards")	-	0	-
Cl 19.11.4.1(Electrostatic discharges)	-	0	-
Cl 19.11.4.2(Radiated fields)	-	0	-
Cl 19.11.4.3(Fast transient bursts)	-	0	-
Cl 19.11.4.4(Voltage surges)	-	0	-
Cl 19.11.4.5(Immunity to conducted disturbances)	-	0	-
Cl 19.11.4.6(Voltage dips and interruptions)	-	0	-
Cl 19.11.4.7(Harmonics and inter-harmonics)	-	0	-
Cl 19.11.4.8(Abnormal operation)	-	0	-
24.101(Components)	-	0	-

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion:Cl 24 (Components), Cl 32 ("Radiation, toxicity and similar hazards")

IS 302 : Part 2 : Sec 42 (2024)

Household and Similar Electrical Appliancesï¿½Safety Part 2 Particular Requirements Section 42 Commercial electric forced convection ovens, steam cookers and steam-convection ovens

66000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
11(Heating)	-	4000	-
13.1 &13.2(Leakage current test)	-	1500	-
13.1 &13.3(Electric strength test)	-	1500	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	4000	-
15.3(Moisture resistance)	-	0	Testing charges included in Cl.15
15.101(Moisture resistance)	-	0	Testing charges included in Cl.15
16.1 &16.2(Leakage current test)	-	1500	-
16.1 & 16.3(Electric strength test)	-	1500	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	8000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be Rs. 55000 charged extra.
19.101(Abnormal operation)	-	0	Testing charges included in Cl.19.1 to CL.19.13
20.1(Stability and mechanical hazards)	-	2000	-
20.2(Stability and mechanical hazards)	-	0	Testing charges included in Cl.20.1
20.101(Stability and mechanical hazards)	-	0	Testing charges included in Cl.20.1
20.102(Stability and mechanical hazards)	-	0	Testing charges included in Cl.20.1
21(Mechanical strength)	-	3000	-
21.101(Mechanical strength)	-	0	Testing charges included in Cl.21
22(Construction)	-	8000	-
22.101(Construction)	-	0	Testing charges included in Cl.22
22.102(Construction)	-	0	Testing charges included in Cl.22
22.103(Construction)	-	0	Testing charges included in Cl.22
22.104(Construction)	-	0	Testing charges included in Cl.22
22.105(Construction)	-	0	Testing charges included in Cl.22
22.106(Construction)	-	0	Testing charges included in Cl.22
22.107(Construction)	-	0	Testing charges included in Cl.22
22.108(Construction)	-	0	Testing charges included in Cl.22
22.109(Construction)	-	0	Testing charges included in Cl.22
22.110(Construction)	-	0	Testing charges included in Cl.22
22.111(Construction)	-	0	Testing charges included in Cl.22
22.112(Construction)	-	0	Testing charges included in Cl.22
22.113(Construction)	-	0	Testing charges included in Cl.22
22.114(Construction)	-	0	Testing charges included in Cl.22
22.115(Construction)	-	0	Testing charges included in Cl.22
22.116(Construction)	-	0	Testing charges included in Cl.22
22.117(Construction)	-	0	Testing charges included in Cl.22
22.118(Construction)	-	0	Testing charges included in Cl.22
22.119(Construction)	-	0	Testing charges included in Cl.22
23(Internal wiring)	-	2000	-
24(Components)	-	3000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	3000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-
22.109(Construction)	-	0	Testing charges included in Cl.22
30.101(Resistance to heat and fire)	-	0	Testing charges included in Cl.30
7(Marking and instructions)	-	0	-
8(Protection against access to live parts)	-	0	-
10(Power input and current)	-	0	-
11(Heating)	-	0	-
13.1 &13.2(Leakage current test)	-	0	-
13.1 &13.3(Electric strength test)	-	0	-
14(Transient overvoltages)	-	0	-
15(Moisture resistance)	-	0	-
15.3(Moisture resistance)	-	0	-
15.101(Moisture resistance)	-	0	-
16.1 &16.2(Leakage current test)	-	0	-
16.1 & 16.3(Electric strength test)	-	0	-
17(Overload protection of transformers and associated circuits)	-	0	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	0	-
19.101(Abnormal operation)	-	0	-
20.1(Stability and mechanical hazards)	-	0	-
20.2(Stability and mechanical hazards)	-	0	-
20.101(Stability and mechanical hazards)	-	0	-
20.102(Stability and mechanical hazards)	-	0	-
21(Mechanical strength)	-	0	-
21.101(Mechanical strength)	-	0	-
22(Construction)	-	0	-
22.101(Construction)	-	0	-
22.102(Construction)	-	0	-
22.103(Construction)	-	0	-
22.104(Construction)	-	0	-
22.105(Construction)	-	0	-
22.106(Construction)	-	0	-
22.107(Construction)	-	0	-
22.108(Construction)	-	0	-
22.109(Construction)	-	0	-
22.110(Construction)	-	0	-
22.111(Construction)	-	0	-
22.112(Construction)	-	0	-
22.113(Construction)	-	0	-
22.114(Construction)	-	0	-
22.115(Construction)	-	0	-
22.116(Construction)	-	0	-
22.117(Construction)	-	0	-
22.118(Construction)	-	0	-
22.119(Construction)	-	0	-
23(Internal wiring)	-	0	-
24(Components)	-	0	-
25("Supply connection and external flexible cords")	-	0	-
26("Terminals for external conductors")	-	0	-
27(Provision for earthing)	-	0	-
28(Screws and connections)	-	0	-
29("Clearances, creepage distances and solid insulation")	-	0	-
30(Resistance to heat and fire)	-	0	-
31(Resistance to rusting)	-	0	-
32("Radiation, toxicity and similar hazards")	-	0	-
22.109(Construction)	-	0	-
30.101(Resistance to heat and fire)	-	0	-

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion: Cl 24 (Components), Cl 32 ("Radiation, toxicity and similar hazards")

IS 302 : Part 2 : Sec 13 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 13 Deep Fat Fryers, Frying Pans and Similar Appliances (First Revision)

66000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	2000	-
8(Protection against access to live parts)	-	2000	-
10(Power input and current)	-	2000	-
11(Heating)	-	4000	-
13.1 &13.2(Leakage current test)	-	1500	-
13.1 &13.3(Electric strength test)	-	1500	-
14(Transient overvoltages)	-	2000	-
15(Moisture resistance)	-	4000	-
15.3(Moisture resistance)	-	0	Testing charges included in Cl.15
15.101(Moisture resistance)	-	0	Testing charges included in Cl.15
16.1 &16.2(Leakage current test)	-	1500	-
16.1 & 16.3(Electric strength test)	-	1500	-
17(Overload protection of transformers and associated circuits)	-	4000	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	8000	Charges applicable excluding the test of Cl.19.11.4.1 to Cl.19.11.4.7. The testing charges for EMI/EMC Testing (Cl.19.11.4.1 to Cl.19.11.4.7) will be charged extra.
19.101 to to 19.102(Abnormal operation)	-	0	Testing charges included in Cl.19.1 to CL.19.13
20(Stability and mechanical hazards)	-	2000	-
21(Mechanical strength)	-	3000	-
22(Construction)	-	8000	-
22.101(Construction)	-	0	Testing charges included in Cl.22
23(Internal wiring)	-	2000	-
24(Components)	-	3000	-
25("Supply connection and external flexible cords")	-	1000	-
26("Terminals for external conductors")	-	1000	-
27(Provision for earthing)	-	2000	-
28(Screws and connections)	-	1000	-
29("Clearances, creepage distances and solid insulation")	-	2000	-
30(Resistance to heat and fire)	-	3000	-
31(Resistance to rusting)	-	1000	-
32("Radiation, toxicity and similar hazards")	-	1000	-

20 Jun, 2028

-
Included w.e.f 25.03.2025 Exclusion: Cl 24 (Components), Cl 32 ("Radiation, toxicity and similar hazards")

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Hi Physix Laboratory India Private Limited, Pune

B-32/1/2, MIDC, Industrial Area, Ranjangaon, Pune, Pune, Pune, Maharashtra, 412220

8552003805 infohplindia@bureauveritas.com

Scope List