61 |
IS 14286 : Part 1 : Sec 4 (2019) |
Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 4 special requirements for testing of thin - Film Cu(In,ga)(S,se)2 based photovoltaic (Pv) modules (Second Revision) |
-
|
1465000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
11.3(Insulation test (MQT 03)) |
- |
5000 |
|
- |
11.4(Measurement of temperature coefficients (MQT 04)) |
- |
60000 |
|
- |
11.5(Measurement of nominal module operating temperature (NMOT)
(MQT 05)) |
- |
20000 |
|
- |
11.6(Performance at STC and NMOT
(MQT 06)) |
- |
80000 |
|
- |
11.7(Performance at low irradiance
(MQT 07)) |
- |
30000 |
|
- |
11.8(Outdoor exposure test (MQT 08)) |
- |
30000 |
|
- |
11.9(Hot-spot endurance test (MQT 09)) |
- |
200000 |
|
- |
11.1(UV preconditioning test
(MQT 10)) |
- |
100000 |
|
- |
11.11(Thermal cycling test (MQT 11)) |
- |
250000 |
|
- |
11.12(Humidity-freeze test (MQT 12)) |
- |
100000 |
|
- |
11.13(Damp heat test (MQT 13)) |
- |
150000 |
|
- |
11.14(Robustness of terminations
(MQT 14)) |
- |
10000 |
|
- |
11.15(Wet leakage current test (MQT 15)) |
- |
5000 |
|
- |
11.16(Static mechanical load test
(MQT 16)) |
- |
20000 |
|
- |
11.17(Hail test (MQT 17)) |
- |
10000 |
|
- |
11.18(Bypass diode thermal test (MQT 18)) |
- |
80000 |
|
- |
11.19(Stabilization (MQT 19)) |
- |
300000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
62 |
IS 16169 (2019) |
Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures (First Revision) |
-
|
100000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
6(Test for single or multi-phase inverter) |
- |
100000 |
|
Testing Charges mentioned are for Upto 20kW.
For >20kW to 50kW =Rs.150000
For >50kW to 100kW =Rs.200000
For >100kW to 200kW =Rs.300000 |
Annex A(Islanding as it applies to PV systems) |
- |
0 |
|
- |
Annex B(Test for independent islanding device) |
- |
0 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
63 |
IS 1474 (1959) |
Specification for commercial refrigerators |
-
|
350000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
7.5.1(Pressure Test) |
- |
10000 |
|
- |
7.5.3(Insulation Resistance Test (Assembly Test)) |
- |
5000 |
|
- |
7.5.4(Thermal Insulation Test) |
- |
25000 |
|
- |
7.5.5(Condensation Test) |
- |
50000 |
|
- |
7.5.6(Rating Test) |
- |
140000 |
|
- |
7.5.7(Test for Adequate Rating of Compressor Motor) |
- |
80000 |
|
- |
7.5.8(Door Seal Test) |
- |
5000 |
|
- |
3.3.1(Gross Volume) |
- |
5000 |
|
Testing charges are for Cl. 3 |
3.3(Volume of evaporator space) |
- |
0 |
|
Testing charges are mentioned in cl. 3.3.1 |
|
Complete
|
|
20 Jun, 2025 |
- |
64 |
IS 2312 (1967) |
Specification for propeller type AC ventilating fans (First Revision) |
-
|
22400 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
3.1(Sizes ) |
- |
1000 |
|
Testing charges are for Cl. no.3 |
4.1(Rated Voltage) |
- |
0 |
|
- |
5.1(Rated frequency) |
- |
0 |
|
- |
6.1(Design and General Construction) |
- |
2000 |
|
Testing charges are for Cl. no.6 |
6.3(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.3(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.4(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.5(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.6(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.7(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.9(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.1(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.11(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
6.12(Design and General Construction) |
- |
0 |
|
Testing charges are for Cl. no.6.1 |
7.1(Design and General Construction) |
- |
0 |
|
- |
8.1(Design and General Construction) |
- |
0 |
|
- |
9(Design and General Construction) |
- |
0 |
|
- |
10.1(Starting ) |
- |
3000 |
|
Testing charges are for Cl. no.10 |
11.1(Interchangeability) |
- |
2000 |
|
Testing charges are for Cl. no.11 |
13.1(Marking) |
- |
0 |
|
- |
13.1 (a)(Marking) |
- |
0 |
|
- |
13.1 (b)(Marking) |
- |
0 |
|
- |
13.1 (c)(Marking) |
- |
0 |
|
- |
13.1 (d)(Marking) |
- |
0 |
|
- |
13.1 (e)(Marking) |
- |
0 |
|
- |
13.1 (f)(Marking) |
- |
0 |
|
- |
13.1 (g)(Marking) |
- |
0 |
|
- |
13.1 (h)(Marking) |
- |
0 |
|
- |
13.1 (j)(Marking) |
- |
0 |
|
- |
13.2(Marking) |
- |
0 |
|
- |
13.4(Marking) |
- |
0 |
|
- |
14.2 & 15.1(Air Delivery) |
- |
6000 |
|
Testing charges are for Cl. no.14.2 |
14.3.A(Temperature-Rise (for motors)) |
- |
3000 |
|
Testing charges are for Cl. no.14.3 |
14.3.A(Temperature-Rise (for motors)) |
- |
0 |
|
Testing charges are for Cl. no.14.3 |
14.3.A(Temperature-Rise (for motors)) |
- |
0 |
|
Testing charges are for Cl. no.14.3 |
14.3.A(Temperature-Rise (for motors)) |
- |
0 |
|
Testing charges are for Cl. no.14.3 |
14.3.B(Temperature-Rise (for regulators)) |
- |
0 |
|
Testing charges are for Cl. no.14.3 |
14.3.B(Temperature-Rise (for regulators)) |
- |
0 |
|
Testing charges are for Cl. no.14.3 |
14.3.B(Moistureproofness (for regulators only)) |
- |
0 |
|
Testing charges are for Cl. no.14.3 |
14.3.B(Moistureproofness (for regulators only)) |
- |
0 |
|
Testing charges are for Cl. no.14.3 |
14.5(Mechanical Endurance (for regulators only)) |
- |
0 |
|
- |
14.1 & 14.6(Power factor) |
- |
2000 |
|
Testing charges are for Cl. no.14.6 |
14.7(ac leakage) |
- |
1000 |
|
- |
14.8(High voltage test) |
- |
1000 |
|
- |
14.9(Insulation-Resistance) |
- |
3000 |
|
- |
14.1(Earthing continuity) |
- |
2000 |
|
- |
14.11 & 15.1(Electrical Input) |
- |
3000 |
|
Testing charges are for Cl. no.14.11 |
14.12 & 16(Fan Speed) |
- |
4000 |
|
Testing charges are for Cl. no.14.12 |
14.4(Moistureproofness (for regulators only)) |
- |
5000 |
|
- |
14.4(Moistureproofness (for regulators only)) |
- |
0 |
|
Testing charges are for Cl. no.14.4 |
|
Complete
|
|
20 Jun, 2025 |
- |
65 |
IS 1534 : Part 1 (1977) |
Ballasts for fluorescent lamps:Part 1 For switch start circuits |
-
|
72000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
9.13(Performance) |
- |
10000 |
|
- |
9.12(Resistance To Corrosion) |
- |
1000 |
|
- |
9.11(Resistance To Heat) |
- |
3000 |
|
- |
9.1(Test for Mechanical Strength) |
- |
2000 |
|
- |
9.9(Test For Limitations Of Ballast Heating) |
- |
5000 |
|
- |
9.8(Test for Thermal Endurance Of Windings) |
- |
30000 |
|
- |
9.7(Moisture Resistance and Insulation) |
- |
2000 |
|
- |
9.6(Voltage Across Capacitors) |
- |
1000 |
|
- |
9.5(Protection against Accidental Contacts and Electric Shock) |
- |
2000 |
|
- |
9.4(Visual Examination) |
- |
1000 |
|
- |
8(Marking) |
- |
2000 |
|
- |
7(Creepage Distances and Clearances) |
- |
2000 |
|
- |
6(Provision For Earthing) |
- |
2000 |
|
- |
5(Screws, Current-Carrying Parts And Connections) |
- |
1000 |
|
- |
4(Terminals For External Wiring) |
- |
3000 |
|
- |
3(General Design, Construction and workmanship) |
- |
2000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
66 |
IS 366 (1991) |
Electric iron - Specification (Fourth Revision) |
-
|
18450 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
10.0(Measurement of Heating up time) |
- |
3000 |
|
- |
11.0(Measurement of sole plate temperature) |
- |
3000 |
|
- |
12.0(Measurement of Tempearture Distribution) |
- |
3000 |
|
- |
13.0(Measurement of Initial overswing temperature and Heating up excess temperature) |
- |
3000 |
|
- |
14.0(Measurement of Cyclic fluctuation of temperature of hottest point ) |
- |
3000 |
|
0 |
16.0(Measurement of Thermostatic staibility) |
- |
4000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
67 |
IS 13021 : Part 1 (1991) |
AC supplied electronic ballasts for tubular fluorescent lamps - Specification: Part 1 general and safety requirements |
-
|
40000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
6.0(Classification) |
- |
1000 |
|
- |
7.3(Test for Marking) |
- |
2000 |
|
- |
8.1(TERMINALS) |
- |
3000 |
|
- |
9.0(PROVISIONS FOR EARTHING) |
- |
2000 |
|
- |
10, Table 1(Between live parts of different polarity) |
- |
2000 |
|
- |
10, Table 1(Between live parts and acceptable metal parts which are permanently fixed to the ballast including screws or devices for fixing covers or fixing the ballast to its supports clearance) |
- |
0 |
|
Charges already included in clause 10. |
10, Table 1(Between live parts and a Bat supporting surface or a loose metal cover, if any, if the construction does not ensure that the values under 2 above are maintained under
the most unfavourable circumstances ) |
- |
0 |
|
Charges already included in clause 10. |
11.1(Ballasts, which do not rely upon the luminaire enclosure for protection against electric shock) |
- |
3000 |
|
- |
11.2(Ballasts incorporating capacitors) |
- |
0 |
|
Charges already included in clause 11.1 |
12.0(PROTECTION AGAINST ELECTRIC SHOCK) |
- |
3000 |
|
- |
13.0(MOISTURE RESISTANCE AND INSULATION) |
- |
4000 |
|
- |
14.1(ELECTRIC STRENGTH) |
- |
2000 |
|
- |
14.1.1, Table 2(Up to and including 42 V) |
- |
0 |
|
Charges already included in clause 14.1 |
14.1.1, Table 2(Above 42 V up to and including 1000 V) |
- |
0 |
|
Charges already included in clause 14.1 |
15.0(ABNORMAL CONDITIONS) |
- |
5000 |
|
- |
16.1(Short-circuit across creepage distances and clearance in air) |
- |
5000 |
|
- |
16.2(Short-Circuit Across or, if Applicable, Interruption of Semi-conductor Devices) |
- |
0 |
|
Charges already included in clause 16.1 |
16.3(Shert-Circuit Across Insulation Consisting of Covering of Lacquer, Enamel or Textile) |
- |
0 |
|
Charges already included in clause 16.1 |
16.4(Short-circuit across electrolytic capacitors.) |
- |
0 |
|
Charges already included in clause 16.1 |
17.0(Current carrying parts and connections) |
- |
2000 |
|
- |
17.5, Table 3(Nominal Diameter Screw) |
- |
0 |
|
Charges already included in clause 17.0 |
17.5, Table 3(Torque ( Nm ), 1) |
- |
0 |
|
Charges already included in clause 17.0 |
17.5, Table 3(Torque ( Nm ), 2) |
- |
0 |
|
Charges already included in clause 17.0 |
18.3(External parts of insulating material providing protection against electric shock) |
- |
4000 |
|
- |
18.4(Parts of insulating material retaining live parts in position ) |
- |
0 |
|
Charges already included in clause 18.3 |
19.0(RESISTANCE TO CORROSION) |
- |
2000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
68 |
IS 302 : Part 2 : Sec 24 (1994) |
Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 24 refrigerators, food - Freezers and ice - Makers |
-
|
230000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
7.1 , 7.12, 7.14,7.15(Marking) |
- |
5000 |
|
- |
8.1, 8.1.1 & 8.2(Protection against access to live parts) |
- |
5000 |
|
- |
9(Starting of motor operated Appliances) |
- |
5000 |
|
Testing charges are for clause no.9 |
9.1(Startability Test) |
- |
0 |
|
Testing charges are included for clause no.9 |
9.2(Startability Test) |
- |
0 |
|
Testing charges are included for clause no.9 |
11(TEMPERATURE RISE) |
- |
15000 |
|
- |
12,12.1,12.2 & 12.3(Heating) |
- |
10000 |
|
- |
13(ELECTRICAL INSULATION AND
LEAKAGE CURRENT AT OPERATING
TEMPERATURE) |
- |
10000 |
|
- |
14( RADIO AND TELEVISION
INTERFERENCE SUPPRESSION
) |
- |
5000 |
|
- |
15(Moisture resistance) |
- |
20000 |
|
- |
16 & 16.1(INSULATION RESISTANCE AND
ELECTRIC STRENGTH ( After the Humidity
Treatment )) |
- |
10000 |
|
Testing charges are for clause no.16 |
16.2(INSULATION RESISTANCE AND
ELECTRIC STRENGTH ( After the Humidity
Treatment )) |
- |
0 |
|
Testing charges are included for clause no.9 |
16.3 & table(INSULATION RESISTANCE AND
ELECTRIC STRENGTH ( After the Humidity
Treatment )) |
- |
0 |
|
Testing charges are included for clause no.9 |
16.4(INSULATION RESISTANCE AND
ELECTRIC STRENGTH ( After the Humidity
Treatment )) |
- |
0 |
|
Testing charges are included for clause no.9 |
17(Over load Protection ) |
- |
10000 |
|
- |
19(ABNORMAL OPERATION) |
- |
30000 |
|
- |
20.1(Stability and mechanical hazards) |
- |
10000 |
|
Testing charges are for clause no.20.1 |
20.2(Stability and mechanical hazards) |
- |
0 |
|
Testing charges are included for clause no.20.1 |
21.1(MECHANICAL STRENGTH) |
- |
10000 |
|
Testing charges are for clause no.21.1 |
21.2(MECHANICAL STRENGTH) |
- |
0 |
|
Testing charges are included for clause no.21.1 |
22.1(Constructions) |
- |
15000 |
|
Testing charges are for clause no.22.1 |
22.2(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.3(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.4(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.5(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.6(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.7 to 22.10(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.11(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.12(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.13 to 22.33(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
22.101 to 22.103(Constructions) |
- |
0 |
|
Testing charges are included for clause no.22.1 |
23.1 & 23.2(Internal wiring) |
- |
5000 |
|
Testing charges are for clause no.23.1 & 23.2 |
23.3(Internal wiring) |
- |
0 |
|
Testing charges are included for clause no.23.1 & 23.2 |
23.4(Internal wiring) |
- |
0 |
|
Testing charges are included for clause no.23.1 & 23.2 |
23.5 to 23.8(Internal wiring) |
- |
0 |
|
Testing charges are included for clause no.23.1 & 23.2 |
24.1(Components) |
- |
10000 |
|
- |
25.1(Supply connection and external flexible cords) |
- |
5000 |
|
Testing charges are for clause no.25.1 |
25.2(Supply connection and external flexible cords) |
- |
0 |
|
Testing charges are included for clause no.25.1 |
25.3(Supply connection and external flexible cords) |
- |
0 |
|
Testing charges are included for clause no.25.1 |
25.4(Supply connection and external flexible cords) |
- |
0 |
|
Testing charges are included for clause no.25.1 |
25.6(Supply connection and external flexible cords) |
- |
0 |
|
Testing charges are included for clause no.25.1 |
25.7 to 25.13(Supply connection and external flexible cords) |
- |
0 |
|
Testing charges are included for clause no.25.1 |
26.1 to 26.8(Terminals for external conductors) |
- |
5000 |
|
Testing charges are for clause no.26.1 to 26.8 |
26.9(Terminals for external conductors) |
- |
0 |
|
Testing charges are included for clause no.26.1 to 26.8 |
26.10 & 26.13(Terminals for external conductors) |
- |
0 |
|
Testing charges are included for clause no.26.1 to 26.8 |
27.1 to 27.4(Provision for earthing) |
- |
5000 |
|
Testing charges are for clause no. 27.1 to 27.4 |
27.5(Provision for earthing) |
- |
0 |
|
Testing charges are included for clause no. 27.1 to 27.4 |
28.1, Table No.-14(Screws and connections) |
- |
5000 |
|
Testing charges are for clause no. 28.2 to 28.4 |
28.2 to 28.4(Screws and connections) |
- |
0 |
|
Testing charges are included for clause no. 28.2 to 28.4 |
29.1 and table 2(creepage and Clearances distances ) |
- |
5000 |
|
Testing charges are for clause no. 29.1 |
29.2 & 29.3(Clearances, creepage distances ) |
- |
0 |
|
Testing charges are included for clause no. 29.1 |
30.1(Resistance to heat and fire) |
- |
10000 |
|
Testing charges are for clause no. 30.1 |
30.2(Resistance to heat and fire) |
- |
0 |
|
Testing charges are included for clause no. 30.1 |
30.3(Resistance to heat and fire) |
- |
0 |
|
Testing charges are included for clause no. 30.1 |
31(Resistance to rusting) |
- |
5000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
69 |
IS 616 (2017) |
Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision) |
-
|
135000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
5(Marking and instructions) |
- |
3000 |
|
- |
7(Heating under normal operating conditions) |
- |
10000 |
|
- |
8(Constructional requirements with regard to the protection against electric shock) |
- |
8000 |
|
- |
9(Electric shock hazard under normal operating conditions) |
- |
5000 |
|
- |
10(Insulation requirements) |
- |
35000 |
|
Charges for Cl. No.10 will be variable as per the size of the products. Minimum charges are Rs.10000 |
11(Fault conditions) |
- |
10000 |
|
- |
12(Mechanical strength) |
- |
10000 |
|
- |
13(CLEARANCES and CREEPAGE DISTANCES) |
- |
15000 |
|
- |
14(Components) |
- |
10000 |
|
- |
15(TERMINALS) |
- |
3000 |
|
- |
16(External flexible cords) |
- |
5000 |
|
- |
17(Electrical connections and mechanical fixings) |
- |
3000 |
|
- |
19(Stability and mechanical hazards) |
- |
10000 |
|
- |
20(Resistance to fire) |
- |
8000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
70 |
IS 13252 : Part 1 (2010) |
Information technology equipment - Safety: Part 1 general requirements (Second Revision) |
-
|
138952 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
1.5(Components) |
- |
5000 |
|
- |
1.6(Power interface .) |
- |
5000 |
|
- |
1.7(Markings and instructions) |
- |
3000 |
|
- |
2.1(Protection from electric shock and energy hazards) |
- |
5000 |
|
- |
2.2(SELV circuits) |
- |
5000 |
|
- |
2.3(TNV circuits) |
- |
5000 |
|
- |
2.4(Limited current circuits) |
- |
3000 |
|
- |
2.5(Limited power sources .) |
- |
5000 |
|
- |
2.6(Provisions for earthing and bonding) |
- |
5000 |
|
- |
2.7(Overcurrent and earth fault protection in primary circuits) |
- |
3000 |
|
- |
2.8(Safety interlocks) |
- |
0 |
|
- |
2.9(Electrical insulation) |
- |
35000 |
|
Testing charges for Cl. 2.9 will be variable as per size of products .Minimum charges will be 10000. |
2.10(Clearances, creepage distances and distances through insulation) |
- |
10000 |
|
- |
3.1(General) |
- |
2000 |
|
- |
3.2(Connection to a mains supply) |
- |
3000 |
|
- |
3.3(Wiring terminals for connection of external conductors) |
- |
5000 |
|
- |
3.4(Disconnection from the mains supply) |
- |
3000 |
|
- |
3.5(Interconnection of equipment) |
- |
3000 |
|
- |
4.1(Stability) |
- |
5000 |
|
- |
4.2(Mechanical strength) |
- |
5000 |
|
- |
4.3(Design and construction) |
- |
8000 |
|
- |
4.4(Protection against hazardous moving parts) |
- |
5000 |
|
- |
4.5(Thermal requirements) |
- |
5000 |
|
- |
4.6(Openings in enclosures) |
- |
4000 |
|
- |
4.7(Resistance to fire) |
- |
5000 |
|
- |
5.1(Touch current and protective conductor curren) |
- |
3000 |
|
- |
5.2(Electric strength) |
- |
3000 |
|
- |
5.3(Abnormal operating and fault conditions) |
- |
5000 |
|
- |
6.1(Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment) |
- |
2000 |
|
- |
6.2(Protection of equipment users from overvoltages on networks telecommunication) |
- |
2000 |
|
- |
6.3(Protection of the telecommunication wiring system from overheating) |
- |
3000 |
|
- |
7.1(General) |
- |
2000 |
|
- |
7.2(Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment) |
- |
5000 |
|
- |
7.3(Protection of equipment users from overvoltages on the cable distribution system) |
- |
5000 |
|
- |
7.4(Insulation between primary circuits and cable distribution systems) |
- |
3000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
71 |
IS 13585 : Part 1 (2012) |
Shunt power capacitors of the non - Self - Healing type for ac systems having a rated voltage up to and including 1 000 v: Part 1 general - Performance, testing and rating - Safety requirements - Guide for installation and operation (First Revision) |
-
|
251050 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
7.1(Capacitance measurement and output calculation : Measuring procedure
) |
- |
24000 |
|
Testing Charges are for Cl. no. 7
Testing Charges for 01-10kVR are Rs.13000.
Testing Charges for 11-30kVR are Rs.19000. |
7.2( Capacitance tolerances) |
- |
0 |
|
Testing Charges are included in Cl. no. 7.1. |
8.1(Measurement of the tangent of the loss angle (tan S) of the capacitor) |
- |
11000 |
|
Testing Charges are for Cl. no. 8
Testing Charges for 01-10kVR are Rs.8000.
Testing Charges for 11-30kVR are Rs.9500. |
8.2(Measurement of the tangent of the loss angle (tan S) of the capacitor : Loss requirements) |
- |
0 |
|
Testing Charges are included in Cl. no. 8.1. |
9.1(Voltage test between terminals (routine test)) |
- |
3000 |
|
Testing Charges are for Cl. no. 9
Testing Charges for 01-10kVR are Rs.5000.
Testing Charges for 11-30kVR are Rs.4000. |
9.2(Voltage test between terminals (type test)) |
- |
0 |
|
Testing Charges are included in Cl. no. 9.1. |
10.1(Voltage test between terminals and containe (Routine test)) |
- |
3000 |
|
Testing Charges are for Cl. no. 10
Testing Charges for 01-10kVR are Rs.5000.
Testing Charges for 11-30kVR are Rs.4000. |
10.2(Voltage test between terminals and container (type test)) |
- |
0 |
|
Testing Charges are included in Cl. no. 10.1. |
11(Test of internal discharge device) |
- |
11000 |
|
Testing Charges are for Cl. no. 11 & 22
Testing Charges for 01-10kVR are Rs.8000.
Testing Charges for 11-30kVR are Rs.9500. |
12(Sealing test) |
- |
11000 |
|
Testing Charges for 01-10kVR are Rs.8000.
Testing Charges for 11-30kVR are Rs.9500. |
13(Thermal stability test) |
- |
24000 |
|
Testing Charges for 01-10kVR are Rs.13000.
Testing Charges for 11-30kVR are Rs.19000. |
14(Measurement of the tangent of the loss angle (tan 8) of the capacitor
at elevated temperature) |
- |
24000 |
|
Testing Charges for 01-10kVR are Rs.13000.
Testing Charges for 11-30kVR are Rs.19000. |
15(Lightning impulse voltage test between terminals and container () |
- |
3000 |
|
Testing Charges for 01-10kVR are Rs.5000.
Testing Charges for 11-30kVR are Rs.4000. |
16(Discharge test) |
- |
12000 |
|
Testing Charges for 01-10kVR are Rs.6000.
Testing Charges for 11-30kVR are Rs.9500. |
17(Ageing test) |
- |
47550 |
|
Testing Charges for 01-10kVR are Rs.51150.
Testing Charges for 11-30kVR are Rs.48000. |
19(Destruction test) |
- |
31000 |
|
Testing Charges for 01-10kVR are Rs.26000.
Testing Charges for 11-30kVR are Rs.28350. |
26.1(Marking : Rating plate) |
- |
1500 |
|
Testing Charges are for Cl.no. 26 & 27
Testing Charges for 01-10kVR are Rs.2500.
Testing Charges for 11-30kVR are Rs.2000. |
26.3(Warning plate) |
- |
0 |
|
Testing Charges are included in Cl. no. 26.1 |
27.1( Instruction sheet or rating plate) |
- |
0 |
|
Testing Charges are included in Cl. no. 26.1 |
6.2 j)(Disconnecting test on internal fuses) |
- |
20000 |
|
Testing Charges for 01-10kVR are Rs.20000
Testing Charges for 11-30kVR are Rs.20000. |
|
Complete
|
|
20 Jun, 2025 |
- |
72 |
IS 418 (2004) |
Tungsten filament lamps for domestic and similar general lighting purposes (Fourth Revision) |
-
|
49500 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
6(Marking, IS 418) |
- |
2000 |
|
2000 up to 25W, 2000 for above 25W to 40W, 2000 for above 40W to 60W, 2000 for above 60W to 100W, 2000 for above 100W to 200W. Charges varies for rated voltage at 110% voltage charges. |
7.1(Lamp Dimensions, IS 418:2004) |
- |
2000 |
|
2000 up to 25W, 2000 for above 25W to 40W, 2000 for above 40W to 60W, 2000 for above 60W to 100W, 2000 for above 100W to 200W. Charges varies for rated voltage at 110% voltage charges. |
7.2(Lamp Dimensions, IS 418:2004) |
- |
0 |
|
2000 up to 25W, 2000 for above 25W to 40W, 2000 for above 40W to 60W, 2000 for above 60W to 100W, 2000 for above 100W to 200W. Charges varies for rated voltage at 110% voltage charges. Charges already included in clause 7.1. |
8.1(Wattage, IS 418) |
- |
8000 |
|
8000 up to 25W, 10000 for above 25W to 40W, 12000 for above 40W to 60W, 15000 for above 60W to 100W, 20000 for above 100W to 200W. Charges varies for rated voltage at 110% voltage charges. |
8.2.1(Luminous Flux Initial, IS 418) |
- |
0 |
|
8000 up to 25W, 10000 for above 25W to 40W, 12000 for above 40W to 60W, 15000 for above 60W to 100W, 20000 for above 100W to 200W. Charges varies for rated voltage at 110% voltage charges. Charges already included in clause 8.1. |
9(Lumen Maintenance, IS 418) |
- |
12500 |
|
12500 up to 25W, 15000 for above 25W to 40W, 17500 for above 40W to 60W, 30000 for above 60W to 100W, 50000 for above 100W to 200W. Charges varies for rated voltage at 110% voltage charges. |
10.1(Life Test Requirements, IS 418) |
- |
25000 |
|
25000 up to 25W, 30000 for above 25W to 40W, 35000 for above 40W to 60W, 60000 for above 60W to 100W, 100000 for above 100W to 200W. Charges varies for rated voltage at 110% voltage charges. |
10.2(Life Test Requirements, IS 418) |
- |
0 |
|
25000 up to 25W, 30000 for above 25W to 40W, 35000 for above 40W to 60W, 60000 for above 60W to 100W, 100000 for above 100W to 200W. Charges varies for rated voltage at 110% voltage charges. Charges already included in clause number 10.1. |
6(Marking, IS 418) |
- |
0 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
73 |
IS 16103 : Part 1 (2012) |
Led modules for general lighting: Part 1 safety requirements |
-
|
37500 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
7(Marking) |
- |
2000 |
|
- |
8(Terminals) |
- |
5000 |
|
- |
9(PROVISION FOR EARTHING) |
- |
2000 |
|
- |
10(Protection against accidental contact with live parts) |
- |
2000 |
|
- |
11(Mositure Resistance and Insulation) |
- |
10000 |
|
- |
12(Electric Strength) |
- |
2000 |
|
- |
13(Fault conditions) |
- |
10000 |
|
- |
15(Construction) |
- |
5000 |
|
- |
16(Creepage distance and clearances) |
- |
3000 |
|
- |
17(Screws, current carrying parts and connections) |
- |
2000 |
|
- |
18(Resistance to heat, fire and tracking) |
- |
5000 |
|
- |
19(Resistance to corrosion) |
- |
2000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
74 |
IS 2418 : Part 2 (2018) |
Tubular fluorescent lamps for general lighting service: Part 2 performance requirements (Second Revision) |
-
|
105000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
Cl 5 of IS 2418:2:2018(MECHANCIAL, PHYSICAL AND STARTING
REQUIREMENTS) |
- |
5000 |
|
- |
Cl 5.1.2 of IS 2418:2:2018(Caps) |
- |
0 |
|
Charges already included in clause number 5. |
Cl 5.1.3 of IS 2418:2:2018(Dimensions) |
- |
0 |
|
Charges already included in clause number 5. |
Cl 5.2 of IS 2418:2:2018( Starting Requirements) |
- |
5000 |
|
- |
Cl 6 of IS 2418:2:2018(MARKING) |
- |
2000 |
|
- |
Cl 7.3 of IS 2418:2:2018(Visual Examination and Checking for Marking) |
- |
0 |
|
- |
Cl 7.4 of IS 2418:2:2018(Burning Test) |
- |
3000 |
|
- |
Cl 7.5 of IS 2418:2:2018(Starting Characteristics) |
- |
0 |
|
Charges already included in clause number 5.2. |
Cl 7.6 of IS 2418:2:2018(Test for Electrical Luminous and Colour
Characteristics) |
- |
30000 |
|
- |
Cl 7.7 of IS 2418:2:2018(Chromaticity Co-ordinates
) |
- |
0 |
|
Charges already included in clause number 7.6. |
Cl 7.8 of IS 2418:2:2018(Life and Lumen Maintenance) |
- |
60000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
75 |
IS 9974 : Part 1 (1981) |
Specification for high pressure sodium vapour lamps: Part 1 general requirements and tests |
-
|
57000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
5.1(MARKING : Mark of origin) |
- |
2000 |
|
2000 for 70W, 2000 for above 70W to 150W, 2000 for above 150W to 250W, 2000 for above 250W to 400W. |
5.1(MARKING : Rated wattage; ) |
- |
0 |
|
2000 for 70W, 2000 for above 70W to 150W, 2000 for above 150W to 250W, 2000 for above 250W to 400W.
Charges already included in clause number 5.1 (Marking: Mark and Origin). |
5.1(MARKING : Country of manufacture; ) |
- |
0 |
|
2000 for 70W, 2000 for above 70W to 150W, 2000 for above 150W to 250W, 2000 for above 250W to 400W.
Charges already included in clause number 5.1 (Marking: Mark and Origin). |
5.1(MARKING : Lamp designation ) |
- |
0 |
|
2000 for 70W, 2000 for above 70W to 150W, 2000 for above 150W to 250W, 2000 for above 250W to 400W.
Charges already included in clause number 5.1 (Marking: Mark and Origin). |
5.1(MARKING : Rated voltage or voltage range. ) |
- |
0 |
|
2000 for 70W, 2000 for above 70W to 150W, 2000 for above 150W to 250W, 2000 for above 250W to 400W.
Charges already included in clause number 5.1 (Marking: Mark and Origin). |
7.2.1(Lamp Starting Test : Lamp with External Starter) |
- |
3000 |
|
3000 for 70W, 3000 for above 70W to 150W, 3000 for above 150W to 250W, 3000 for above 250W to 400W. |
7.2.2(Lamp Starting Test : Lamp with Internal Starter) |
- |
0 |
|
3000 for 70W, 3000 for above 70W to 150W, 3000 for above 150W to 250W, 3000 for above 250W to 400W.
Charges already included in clause number 7.2.1 |
7.3.1(Lamp Worm-Up Test) |
- |
2000 |
|
2000 for 70W, 2000 for above 70W to 150W, 2000 for above 150W to 250W, 2000 for above 250W to 400W. |
7.3.2(Lamp Worm-Up Test) |
- |
0 |
|
2000 for 70W, 2000 for above 70W to 150W, 2000 for above 150W to 250W, 2000 for above 250W to 400W.
Charges already included in clause number 7.3.1 |
7.4.1(Lamp Electrical Characteristics : Ageing) |
- |
15000 |
|
15000 for 70W, 15000 for above 70W to 150W, 15000 for above 150W to 250W, 15000 for above 250W to 400W. |
4.1(Lamp Dimensions ) |
- |
1000 |
|
1000 for 70W, 1000 for above 70W to 150W, 1000 for above 150W to 250W, 1000 for above 250W to 400W. |
4.2(Glass Bulb) |
- |
0 |
|
- |
4.3.1(Caps) |
- |
1000 |
|
1000 for 70W, 1000 for above 70W to 150W, 1000 for above 150W to 250W, 1000 for above 250W to 400W. |
4.3.3(Caps) |
- |
2000 |
|
2000 for 70W, 2000 for above 70W to 150W, 2000 for above 150W to 250W, 2000 for above 250W to 400W. |
4.3.4(Caps : Insulation Resistance) |
- |
1000 |
|
1000 for 70W, 1000 for above 70W to 150W, 1000 for above 150W to 250W, 1000 for above 250W to 400W. |
10.1(5 000 hours operation, ) |
- |
30000 |
|
30000 for 70W, 40000 for above 70W to 150W, 60000 for above 150W to 250W, 90000 for above 250W to 400W. |
10.2(Life Test) |
- |
0 |
|
30000 for 70W, 40000 for above 70W to 150W, 60000 for above 150W to 250W, 90000 for above 250W to 400W.
Charges already included in clause number 10.1 |
10.2.1(Switching ‘on’ and switching ‘off’ during life test) |
- |
0 |
|
30000 for 70W, 40000 for above 70W to 150W, 60000 for above 150W to 250W, 90000 for above 250W to 400W.
Charges already included in clause number 10.1 |
|
Complete
|
|
20 Jun, 2025 |
- |
76 |
IS 10322 : Part 5 : Sec 8 (2013) |
Luminaires: Part 5 particular requirements: Sec 8 emergency lighting |
-
|
185000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
4(General Test Requireements) |
- |
0 |
|
- |
5(Classification of Luminaires') |
- |
0 |
|
- |
6.0(Marking) |
- |
2000 |
|
- |
7.0(Construction) |
- |
50000 |
|
- |
8.0(Creepage Distance and Clearances) |
- |
2000 |
|
- |
9.0(Provision for earthing) |
- |
2000 |
|
- |
10.0(Terminals) |
- |
1000 |
|
- |
11.0(External & Internal Wiring) |
- |
5000 |
|
- |
12.0(Protection against electric shock) |
- |
2000 |
|
- |
13.0(Endurance Tests and Thermal Tests) |
- |
35000 |
|
- |
14.0(Resistance to Dust & Moisture) |
- |
12000 |
|
- |
15.0(Insulation Resistance and Electric Strength) |
- |
5000 |
|
- |
16.0(Resistance to Heat , fire and tracking) |
- |
5000 |
|
- |
17.0(Functional Safety) |
- |
40000 |
|
- |
18.0(Changeover Operation) |
- |
10000 |
|
- |
19.0(High Temperature Operation) |
- |
5000 |
|
- |
20.0(BATTERY CHARGERS FOR SELFCONTAINED EMERGENCY LUMINAIRES) |
- |
5000 |
|
- |
21.0(TEST DEVICES FOR EMERGENCY OPERATION) |
- |
2000 |
|
- |
22.0(REST MODE AND INIHIBITION MODE FACILITIES) |
- |
2000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
77 |
IS 10322 : Part 5 : Sec 7 (2017) |
Luminaires: Part 5 particular requirements: Sec 7 lighting chains (First Revision) |
-
|
85000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
20.4(General Test Requireements) |
- |
0 |
|
- |
20.5(Classification of Luminaires') |
- |
0 |
|
- |
20.6(Marking) |
- |
2000 |
|
- |
20.7(Construction) |
- |
20000 |
|
- |
20.8(Creepage Distance and Clearances) |
- |
2000 |
|
- |
20.9(Provision for earthing) |
- |
0 |
|
- |
20.10(Terminals) |
- |
1000 |
|
- |
20.11(External & Internal Wiring) |
- |
5000 |
|
- |
20.12(Protection against electric shock) |
- |
8000 |
|
- |
20.13(Endurance Tests and Thermal Tests) |
- |
25000 |
|
- |
20.14(Resistance to Dust & Moisture) |
- |
12000 |
|
- |
20.15(Insulation Resistance and Electric Strength) |
- |
5000 |
|
- |
20.16(Resistance to Heat , fire and tracking) |
- |
5000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
78 |
IS 10322 : Part 5 : Sec 5 (2013) |
Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision) |
-
|
121000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
4(General Test Requireements) |
- |
0 |
|
- |
5(Classification of Luminaires') |
- |
0 |
|
- |
6.0(Marking) |
- |
2000 |
|
- |
7.0(Construction) |
- |
20000 |
|
- |
8.0(Creepage Distance and Clearances) |
- |
2000 |
|
- |
9.0(Provision for earthing) |
- |
2000 |
|
- |
10.0(Terminals) |
- |
1000 |
|
- |
11.0(External & Internal Wiring) |
- |
5000 |
|
- |
12.0(Protection against electric shock) |
- |
2000 |
|
- |
13.0(Endurance Tests and Thermal Tests) |
- |
25000 |
|
- |
14.0(Resistance to Dust & Moisture) |
- |
12000 |
|
- |
15.0(Insulation Resistance and Electric Strength) |
- |
5000 |
|
- |
16.0(Resistance to Heat , fire and tracking) |
- |
5000 |
|
- |
17.0(Photometric Test) |
- |
40000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
79 |
IS 10322 : PART 5 : SEC 3 (2012) |
Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision) |
-
|
121000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
4(General Test Requireements) |
- |
0 |
|
- |
5(Classification of Luminaires') |
- |
0 |
|
- |
6.0(Marking) |
- |
2000 |
|
- |
7.0(Construction) |
- |
20000 |
|
- |
8.0(Creepage Distance and Clearances) |
- |
2000 |
|
- |
9.0(Provision for earthing) |
- |
2000 |
|
- |
10.0(Terminals) |
- |
1000 |
|
- |
11.0(External & Internal Wiring) |
- |
5000 |
|
- |
12.0(Protection against electric shock) |
- |
2000 |
|
- |
13.0(Endurance Tests and Thermal Tests) |
- |
25000 |
|
- |
14.0(Resistance to Dust & Moisture) |
- |
12000 |
|
- |
15.0(Insulation Resistance and Electric Strength) |
- |
5000 |
|
- |
16.0(Resistance to Heat , fire and tracking) |
- |
5000 |
|
- |
17.0(Photometric Test) |
- |
40000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
80 |
IS 10322 : Part 5 : Sec 2 (2012) |
Luminaires: Part 5 particular requirements: Sec 2 recessed luminaires (First Revision) |
-
|
121000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
4(General Test Requireements) |
- |
0 |
|
- |
5(Classification of Luminaires') |
- |
0 |
|
- |
6(Marking) |
- |
2000 |
|
- |
7(Construction) |
- |
20000 |
|
- |
8(Creepage Distance and Clearances) |
- |
2000 |
|
- |
9(Provision for earthing) |
- |
2000 |
|
- |
10(Terminals) |
- |
1000 |
|
- |
11(External & Internal Wiring) |
- |
5000 |
|
- |
12(Protection against electric shock) |
- |
2000 |
|
- |
13(Endurance Tests and Thermal Tests) |
- |
25000 |
|
- |
14(Resistance to Dust and Moisture) |
- |
12000 |
|
- |
15(Insulation Resistance and Electric Strength) |
- |
5000 |
|
- |
16(Resistance to Heat , fire and tracking) |
- |
5000 |
|
- |
17(Photometric Test) |
- |
40000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
81 |
IS 10322 : Part 5 : Sec 1 (2012) |
Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision) |
-
|
121000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
4(General Test Requireements) |
- |
0 |
|
- |
5(Classification of Luminaires') |
- |
0 |
|
- |
6.0(Marking) |
- |
2000 |
|
- |
7.0(Construction) |
- |
20000 |
|
- |
8.0(Creepage Distance and Clearances) |
- |
2000 |
|
- |
9.0(Provision for earthing) |
- |
2000 |
|
- |
10.0(Terminals) |
- |
1000 |
|
- |
11.0(External & Internal Wiring) |
- |
5000 |
|
- |
12.0(Protection against electric shock) |
- |
2000 |
|
- |
13.0(Endurance Tests and Thermal Tests) |
- |
25000 |
|
- |
14.0(Resistance to Dust & Moisture) |
- |
12000 |
|
- |
15.0(Insulation Resistance and Electric Strength) |
- |
5000 |
|
- |
16.0(Resistance to Heat , fire and tracking) |
- |
5000 |
|
- |
17.0(Photometric Test) |
- |
40000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
82 |
IS 15111 : Part 2 (2002) |
Self ballasted lamps for general lighting services: Part 2 performance requirements |
-
|
100000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
6(DIMENSIONS) |
- |
3000 |
|
- |
8.1(STARTING AND RUN-UP) |
- |
3000 |
|
- |
8.2(STARTING AND RUN-UP) |
- |
0 |
|
Testing charges already included in clause number 8.1 |
9(Lamp Wattage) |
- |
3000 |
|
- |
10(Luminous Flux) |
- |
3000 |
|
- |
11(Colour) |
- |
3000 |
|
- |
12(LUMEN MAINTENANCE) |
- |
3000 |
|
- |
13.1(Life) |
- |
30000 |
|
- |
13.2(Life) |
- |
0 |
|
Testing charges already included in clause number 13.1 |
14(Harmonics) |
- |
5000 |
|
- |
15(Lamp Efficacy) |
- |
3000 |
|
- |
16(Power factor) |
- |
2000 |
|
- |
18.1(Marking) |
- |
2000 |
|
- |
18.2(BIS Cirtification Marking) |
- |
0 |
|
Testing charges already included in clause number 18.1 |
|
Complete
|
|
20 Jun, 2025 |
- |
83 |
IS 15111 : PART 1 AND PART 2 (2002) |
Self ballasted lamps for general lighting services: Part 1 safety requirements |
-
|
54000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
6.1(Marking) |
- |
2000 |
|
- |
6.2(Marking) |
- |
0 |
|
Testing charges already included in clause number 6.1 |
6.3(Marking) |
- |
0 |
|
Testing charges already included in clause number 6.1 |
6.4(BIS Certification Marking) |
- |
0 |
|
Testing charges already included in clause number 6.1 |
7(Interchangeability
) |
- |
2000 |
|
- |
8(Protection against electric shock) |
- |
5000 |
|
- |
9.2(Insulation Resistance) |
- |
15000 |
|
- |
9.2(The insulation resistance of
B 22 caps between shell and contact shall be not less than 5
MΩ When measure with a 500 voltage DC.) |
- |
0 |
|
Testing charges already included in clause number 9.2 |
9.3(Electric Strength) |
- |
0 |
|
Testing charges already included in clause number 9.2 |
10(Mechanical strength test
) |
- |
10000 |
|
- |
11(Cap Temperature rise test
) |
- |
5000 |
|
- |
12(Resistance to heat) |
- |
5000 |
|
- |
13(Resistance to Flame and Ignition) |
- |
5000 |
|
- |
14(Fault Conditions) |
- |
5000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
84 |
IS 15885 : Part 2 : Sec 13 (2012) |
Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules |
-
|
50000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
7(Marking) |
- |
2000 |
|
- |
8(Protection against accidental contact with live parts) |
- |
2000 |
|
- |
9(Terminals) |
- |
5000 |
|
- |
10(PROVISION FOR EARTHING) |
- |
4000 |
|
- |
11(MOISTURE RESISTANCE) |
- |
5000 |
|
- |
12(Electric Strength) |
- |
2000 |
|
- |
13(Thermal endurance test for winding of ballasts) |
- |
0 |
|
- |
14(Fault conditions) |
- |
5000 |
|
- |
15(Transformer heating) |
- |
10000 |
|
- |
16(Construction) |
- |
2000 |
|
- |
17(Creepage distance and clearances) |
- |
3000 |
|
- |
18(Screws, current carrying parts and connections) |
- |
3000 |
|
- |
19(Resistance to heat, fire and tracking) |
- |
5000 |
|
- |
20(Resistance to corrosion) |
- |
2000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
85 |
IS 16102 : Part 1 (2012) |
Self - Ballasted led lamps for general lighting services: Part 1 safety requirements |
-
|
65000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
5(Marking) |
- |
2000 |
|
- |
6(Interchangeability) |
- |
12000 |
|
- |
7(Protection against accidental contact with live parts) |
- |
5000 |
|
- |
8(Insulation Resistance and Electric Strength) |
- |
15000 |
|
- |
9(MECHANICAL STRENGTH) |
- |
1000 |
|
- |
10(cap temperature) |
- |
5000 |
|
- |
11(Resistance to Heat) |
- |
5000 |
|
- |
12(Resistance to Flame and Ignition) |
- |
5000 |
|
- |
13(Fault conditions) |
- |
10000 |
|
- |
14(Creepage distance and clearances) |
- |
5000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
86 |
IS 9537 : Part 3 (1983) |
Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials |
-
|
4950 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
7.1.1(Maximum and minimum outside diameter of socket) |
- |
2000 |
|
Testing charges are for cl. no.7. |
7.1.1 Table-2(Length of Socket end) |
- |
0 |
|
Testing charges are for cl. no.7 |
7.1.2(Maximum and minimum outside diameter of conduit) |
- |
0 |
|
Testing charges are for cl. no.7 |
7.2(Minimum inside diameter of conduit) |
- |
0 |
|
Testing charges are for cl. no.7 |
7.3(Length of conduit) |
- |
0 |
|
Testing charges are for cl. no.7 |
6.1(Marking) |
- |
1000 |
|
Testing charges are for Cl.no. 6 |
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980) |
- |
0 |
|
Testing charges are for Cl.no. 6 |
6.3(Standard Mark on Conduit) |
- |
0 |
|
Testing charges are for Cl.no. 6 |
7.4(Unifomity of The wall Thickness) |
- |
0 |
|
Testing charges are for Cl.no. 7 |
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980) |
- |
1000 |
|
Not applicable for acceptance test upto & above 25 mm. |
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C)) |
- |
5000 |
|
Not applicable for type & acceptance test above 25 mm. |
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980) |
- |
5000 |
|
- |
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980) |
- |
15000 |
|
Not applicable for acceptance test upto & above 25 mm. |
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980) |
- |
3000 |
|
Not applicable for type & acceptance test above 25 mm. |
10(Resistance to Heat -Ball presure test) |
- |
3000 |
|
Not applicable for acceptance test upto & above 25 mm. |
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980) |
- |
3000 |
|
- |
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980) |
- |
5000 |
|
- |
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980) |
- |
1000 |
|
- |
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980) |
- |
- |
|
- |
7.1.1 Table-2(Length of Socket end) |
- |
- |
|
- |
7.1.1 Fig.8(Maximum inside diameter of socket) |
- |
- |
|
- |
7.1.2 Fig.1(Maximum outside diameter of conduit) |
- |
- |
|
- |
7.1.2 Fig.2(Minimum outside diameter of conduit) |
- |
- |
|
- |
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980) |
- |
- |
|
- |
9.2(Bending Test At Low Temp (-5 ±2°C)) |
- |
- |
|
- |
9.2(Bending Test At Room Temp) |
- |
- |
|
- |
9.3(Compression Test (after removal of force) as per caluse 9.3.3 of IS: 9537 (Part 1)-1980) |
- |
- |
|
- |
9.3(Compression Test at Full force applied (On load)) |
- |
- |
|
- |
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980) |
- |
- |
|
- |
9.5 Fig.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980) |
- |
- |
|
- |
11.0(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980) |
- |
- |
|
- |
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980) |
- |
- |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
87 |
IS 4250 (1980) |
Specification for domestic electric food - Mixers (Liquidizers And Grinders) (First Revision) |
-
|
24337 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
6(Classification- IS 302-1 ) |
- |
0 |
|
- |
7.1(Marking- IS 302-1) |
- |
1000 |
|
- |
7.2(Marking) |
- |
0 |
|
Testing charges already included in 7.1 |
7.4(Marking) |
- |
0 |
|
Testing charges already included in 7.1 |
7.5(Marking) |
- |
0 |
|
Testing charges already included in 7.1 |
7.6(Marking) |
- |
0 |
|
Testing charges already included in 7.1 |
8( Protection Against Electric Shock, IS 302-1) |
- |
2000 |
|
- |
9(Starting, IS 302-1) |
- |
2000 |
|
- |
10(Power Input and Current, IS 302-1) |
- |
5000 |
|
- |
11(Heating, IS 302-1) |
- |
3000 |
|
- |
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1) |
- |
3000 |
|
- |
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1) |
- |
0 |
|
Testing charges already included in 13 |
14(Transient Over Voltages, IS 302-1) |
- |
1000 |
|
- |
15.1(Moisture Resistance, IS 302-1) |
- |
0 |
|
Testing charges already included in 15 |
15.2(Moisture Resistance-Spillage test) |
- |
0 |
|
Testing charges already included in 15 |
15(Moisture Resistance, IS 302-1) |
- |
3000 |
|
- |
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1) |
- |
3000 |
|
- |
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1) |
- |
0 |
|
Testing charges already included in 16 |
Cl.18(Endurance) |
- |
5000 |
|
- |
19(Abnormal Operation, IS 302-1) |
- |
4000 |
|
- |
20(Stability & Mechanical Hazards, IS 302-1) |
- |
2000 |
|
- |
21(Mechanical Strength, IS 302-1) |
- |
1000 |
|
- |
22.1(Construction, IS 302-1) |
- |
2000 |
|
- |
22.2(Construction) |
- |
0 |
|
Testing charges already included in 22.1 |
22.3(Construction) |
- |
0 |
|
Testing charges already included in 22.1 |
22.4(Construction) |
- |
0 |
|
Testing charges already included in 22.1 |
22.5(Construction) |
- |
0 |
|
Testing charges already included in 22.1 |
22.6(Construction) |
- |
0 |
|
Testing charges already included in 22.1 |
22.8(Construction) |
- |
0 |
|
Testing charges already included in 22.1 |
22.9(Construction) |
- |
0 |
|
Testing charges already included in 22.1 |
23(Internal Wiring, IS 302-1) |
- |
1000 |
|
- |
24.1(Components, IS 302-1) |
- |
1000 |
|
- |
26(Terminals for External Conductors, IS 302-1) |
- |
1000 |
|
- |
27(Provision for Earthing, IS 302-1) |
- |
2000 |
|
- |
28(Screws & Connections, IS 302-1) |
- |
1000 |
|
- |
35(Temperature withstand test for bowl) |
- |
3000 |
|
- |
36(Test for controls ) |
- |
1000 |
|
- |
37(Strength of Assembly ) |
- |
2000 |
|
- |
25(Supply Connection and External Flexible Cords, IS 302-1) |
- |
1000 |
|
- |
29(Clearances and Distances through Insulation, IS 302-1) |
- |
1000 |
|
- |
30(Resistance to Heat, Fire, Tracking, IS 302-1) |
- |
2000 |
|
- |
31(Resistance of Rusting, IS 302-1) |
- |
1000 |
|
- |
34.2(Operational tests- Grinding coffee (for machines which have a dry grinding arrangement)) |
- |
5000 |
|
- |
34.3(Whisking egg whites ) |
- |
0 |
|
Testing charges already included in 34.2 |
34.4(IDLI batter-Grinding of black gram) |
- |
0 |
|
Testing charges already included in 34.2 |
34.4(IDLI batter-Grinding of rice) |
- |
0 |
|
Testing charges already included in 34.2 |
34.5.1 (a)(Operational test for juicers ) |
- |
0 |
|
Testing charges already included in 34.2 |
34.5.1 (b)(Operational test for juicers ) |
- |
0 |
|
Testing charges already included in 34.2 |
34.5.2(Operational test for juicers ) |
- |
0 |
|
Testing charges already included in 34.2 |
|
Complete
|
|
20 Jun, 2025 |
- |
88 |
IS 302 : Part 2 : Sec 26 (2014) |
Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 26 clocks (First Revision) |
-
|
50000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
6.0(Classification) |
- |
0 |
|
- |
7(Marking and instructions) |
- |
1000 |
|
- |
8(Protection against live parts) |
- |
2000 |
|
- |
10(POWER INPUT AND CURRENT) |
- |
0 |
|
- |
11(HEATING) |
- |
4000 |
|
- |
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE) |
- |
3000 |
|
- |
14(TRANSIENT OVERVOLTAGES) |
- |
1000 |
|
- |
15(MOISTURE RESISTANCE) |
- |
4000 |
|
- |
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH) |
- |
3000 |
|
- |
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS) |
- |
0 |
|
- |
19(ABNORMAL OPERATION) |
- |
3000 |
|
- |
20(STABILITY AND MECHANICAL HAZARDS) |
- |
2000 |
|
- |
21(MECHANICAL STRENGTH) |
- |
2000 |
|
- |
22(CONSTRUCTION) |
- |
2000 |
|
- |
23(INTERNAL WIRING) |
- |
2000 |
|
- |
24(COMPONENTS) |
- |
3000 |
|
- |
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS) |
- |
2000 |
|
- |
26(TERMINALS FOR EXTERNAL CONDUCTORS) |
- |
2000 |
|
- |
27(PROVISION FOR EARTHING) |
- |
2000 |
|
- |
28(SCREWS AND CONNECTIONS) |
- |
2000 |
|
- |
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION) |
- |
2000 |
|
- |
30(RESISTANCE TO HEAT AND FIRE) |
- |
4000 |
|
- |
31(RESISTANCE TO RUSTING) |
- |
1000 |
|
- |
32(RADIATION, TOXICITY AND SIMILAR HAZARDS) |
- |
1000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
89 |
IS 2993 (1998) |
A.C. motor capacitors (Second Revision) |
-
|
455750 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
2.5(Tangent of loss angle) |
- |
18000 |
|
- |
2.6(Visual Examination) |
- |
4000 |
|
- |
2.7(Voltage test between terminals) |
- |
9000 |
|
- |
2.8(Voltage test between terminals and case) |
- |
9000 |
|
- |
2.9(Capacitance measurement) |
- |
13500 |
|
- |
2.1(Check of dimensions) |
- |
4000 |
|
- |
2.11.1(Robustness of terminations) |
- |
18000 |
|
- |
2.11.1.1(Tensile) |
- |
4000 |
|
- |
2.11.1.2(Bending (half cf the terminations)) |
- |
4000 |
|
- |
2.11 .1.3(Torsion (other half of the terminations)) |
- |
4000 |
|
- |
2.11.1.4(Torque (screw terminals)) |
- |
4000 |
|
- |
2.11.1.5(Visual Examination) |
- |
2000 |
|
- |
2.11.2(Soldering) |
- |
5000 |
|
- |
2.11.3(Vibration) |
- |
20000 |
|
- |
2.11.4(fixing bolt or stud (if fitted)) |
- |
1500 |
|
- |
2.12(Sealing Test) |
- |
9000 |
|
- |
2.13(Endurance test) |
- |
177000 |
|
- |
2.13.1(Endurance test :Testing in air with forced circulation) |
- |
0 |
|
Testing charges are included in Cl. no. 2.13 |
2.13.3(Endurance test : Conditions of compliance) |
- |
0 |
|
Testing charges are included in Cl. no. 2.13 |
2.14(Damping heat test) |
- |
66000 |
|
- |
2.15(Self-healing test (if applicable)) |
- |
9000 |
|
- |
2.16.3(Destruction test : Test procedure) |
- |
44250 |
|
- |
2.16.3.1(Destruction test : Test procedure - Preparation and pre-conditioning ) |
- |
0 |
|
Testing charges are included in Cl. no. 2.16.3 |
2.16.3.2(Destruction test : Test procedure : DC conditioning) |
- |
0 |
|
Testing charges are included in Cl. no. 2.16.3 |
2.16.3.3(Destruction test : Test procedure : AC destruction test) |
- |
0 |
|
Testing charges are included in Cl. no. 2.16.3 |
2.16.4(Destruction tes: Evaluation of the failure ) |
- |
0 |
|
Testing charges are included in Cl. no. 2.16.3 |
5.1(Check marking) |
- |
4000 |
|
- |
|
Complete
|
|
20 Jun, 2025 |
- |
90 |
IS 14927 : Part 2 (2001) |
Cable Trunking and Ducting Systems for Electrical Installations : Part 2 Cable Trunking and Ducting Systems Intended for Mounting on Walls or Ceiling |
-
|
18000 View breakup
-
Clause No. |
Exclusion |
Testing Charges (Excl. Of Taxes) |
Effective Date |
Remark |
7.1(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001)) |
- |
1000 |
|
Testing Charges are for Cl. 7 |
7.1(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001)) |
- |
0 |
|
Testing Charges are for Cl. 7 |
7.1(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001)) |
- |
0 |
|
Testing Charges are for Cl. 7 |
7.2(Marking (as per Cl 7.2 of IS:14927(Pt-I ):2001)) |
- |
0 |
|
Testing Charges are for Cl. 7 |
8.1( Dimensions (As per cl.8.1 of IS 14927(Pt-1) : 2001)) |
- |
2000 |
|
Testing Charges are for Cl. 8 |
8.2(Dimensions (As per cl.8.2 of IS 14927(Pt-1) : 2001) |
- |
0 |
|
Testing Charges are for Cl. 8 |
8.3, table 2( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001)) |
- |
0 |
|
Testing Charges are for Cl. 8 |
8.3, table 2( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001)) |
- |
0 |
|
Testing Charges are for Cl. 8 |
8.3, table 2( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001)) |
- |
0 |
|
Testing Charges are for Cl. 8 |
9.1(Construction ( As per Cl. 9.1 of IS 14927(Pt-1):2001)) |
- |
3000 |
|
Testing Charges are for Cl. 9 |
9.2(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001)) |
- |
0 |
|
Testing Charges are for Cl. 9 |
9.3(Construction ( As per Cl. 9.3 of IS 14927(Pt-1):2001)) |
- |
0 |
|
Testing Charges are for Cl. 9 |
9.3.1(Construction ( As per Cl. 9.3.1 of IS 14927(Pt-1):2001)) |
- |
0 |
|
Testing Charges are for Cl. 9 |
9.4.1(Construction [Access to Live Parts (As per Cl. 9.4.1 of IS 14927(Pt-1):2001)]) |
- |
2000 |
|
Testing Charges are for Cl. 9.4 |
9.5(Construction (As per Cl. 9.5 of IS 14927(Pt-1):2001)) |
- |
0 |
|
- |
9.6.2(Construction [Membranes (As per Cl.9.6.2 of IS: 14927 (Pt-1):2001)]) |
- |
1000 |
|
Testing Charges are for Cl.9.6 |
9.6.4(Construction [Membranes (As per Cl.9.6.4 of IS: 14927 (Pt-1):2001)]) |
- |
0 |
|
Testing Charges are for Cl.9.6 |
9.7.2, table 4(Construction [Glands (As per Cl.9.7.2 and Table-4 of IS: 14927 (Pt-1):2001)] ) |
- |
1000 |
|
Testing Charges are for Cl.9.7 |
10(Mechanical Properties ) |
- |
0 |
|
- |
10.2(Cable supporting test for Surface mounting (As per Cl.10.2)) |
- |
2000 |
|
Testing Charges are for Cl.10.2 |
10.2(Cable supporting test for Surface mounting (As per Cl.10.2)) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.2(Cable supporting test for Surface mounting (As per Cl.10.2)) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.2(Cable supporting test for Surface mounting (As per Cl.10.2)) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.2(Cable supporting test for Surface mounting (As per Cl.10.2)) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.2.3(Cable supporting test for Surface mounting (As per Cl.10.2.3)) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.2.3(Cable supporting test for Surface mounting (As per Cl.10.2.3)) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.2.3(Cable supporting test for Surface mounting (As per Cl.10.2.3)) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.2.3(Cable supporting test for Surface mounting (As per Cl.10.2.3)) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.3(Impact Test [ Cl.10.3 ]) |
- |
10000 |
|
- |
10.3.4(Impact Test (As per Cl. 10.3.4 of IS: 14927(Pt-1):2001) ) |
- |
0 |
|
Testing Charges are for Cl.10.2 |
10.4(Linear Deflection Test [ Cl.10.4 ]) |
- |
0 |
|
- |
10.5(External load Test [ Cl.10.5 ]) |
- |
5000 |
|
- |
11.1.1(Resistance to flame propagation (As per Cl. 11.1.1)) |
- |
5000 |
|
Testing Charges are for Cl.11 |
11.1.1(Resistance to flame propagation (As per Cl. 11.1.1)) |
- |
0 |
|
Testing Charges are for Cl.11 |
12.2(Electrical continuity Test for earthing or bonding [ Cl.12.2 ]) |
- |
5000 |
|
Testing Charges are for Cl.12 |
12.2(Electrical continuity Test for earthing or bonding [ Cl.12.2 ]) |
- |
0 |
|
Testing Charges are for Cl.12 |
12.3(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ]) |
- |
0 |
|
Testing Charges are for Cl.12 |
12.3(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ]) |
- |
0 |
|
Testing Charges are for Cl.12 |
12.3(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ]) |
- |
0 |
|
Testing Charges are for Cl.12 |
9.3.2, table 3(Construction ( As per Cl. 9.3.2, Table-3 of IS 14927(Pt-1):2001)) |
- |
0 |
|
Testing Charges are for Cl.9 |
7.101(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001)) |
- |
0 |
|
Testing Charges are for Cl.7 |
7.102(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001)) |
- |
0 |
|
Testing Charges are for Cl.7 |
9.1.101(Construction) |
- |
0 |
|
Testing Charges are for Cl.9 |
|
Complete
|
|
20 Jun, 2025 |
- |