BIS - LIMS (Laboratory Information Management System)

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrol@bis.gov.in

Scope List

Reset

309 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

211

IS 3575 (1993)

Bitumen drums - Specification (Third Revision)

- View breakup
Rs. 1800/- and Material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimensions Drums (Figure 1))	-
4.1 (Dimensions Closure (Figure 2))	-
7.1 (Finish)	-
7.2 (Finish)	-

Partial

-
Except air pressure test and Microalloying elements

212

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1,Table 4&Table 6 (Tensile Test - IS 1608(Pt -1))	-
10.2,Table 4&Table 5 (Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-
17 (Dimension and tolerance)	-
6 (Freedom from defects , IS 6911)	-
15 (Surface Finish)	-

Partial

-
Facility for chemical testing is not available, Erichsen Cupping(Cl11), Corrosion(Cl 12), Proof stress

213

IS 903 (1993)

Specification for Fire Hose Delivery Couplings, Branch Pipe, Nozzles And Nozzle Spanner - Specificaion

Rs 3600/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Finish and workmanship)	-
4 (Marking)	-
6 (Branch pipe)	-
6.3 (Hydraulic test requirement)	-
7 (Nozzle)	-
7.3 (Hydraulic test requirement)	-
5 (Delivery hose coupling)	-
5.3 (Size and Dimension )	-
5.4 (Hydraulic test requirement)	-

Partial

-
Facility for chemical testing is not available

214

IS 3502 (2009)

Steel chequered plates (Third Revision)

- View breakup
Rs. 2985/- and material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 10 (Length, Width, Thickness & Chequered Height)	-
Cl 5 (Workmanship)	-
Cl 6 (Workmanship)	-
Cl.4.1 (IS-2062, E250A) (CARBON)	-
Cl.4.1 (IS-2062, E250A) (SULPHUR)	-
Cl.4.1 (IS-2062, E250A) (PHOSPHURS)	-
Cl.4.1 (IS-2062, E250A) (MANGANESE)	-
Cl.4.1 (IS-2062, E250A) (SILICON)	-
Cl.4.1 (IS-2062, E250A) (CARBON EQUIVALENT)	-
Cl.4.1 (IS-2062, E250A) (NITROGEN)	-

Partial

-
Excluding Microalloying Elements

215

IS 1038 (1983)

Specification For Steel Doors, Windows And Ventilators

- View breakup
Hence complete testing charges for the product are Rs.3000.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1. (Size-Height)	-
4.1 (Size-Width)	-
6.2 (Side Hung Shutter-Width of hinge)	-
6.2 (Side Hung Shutter- Thickness of hinge)	-
6.2 (Side Hung Shutter- Pin diameter)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate- Thicknesss of handle)	-
6.2.2 & 6.2.2.1 (Handle and Handle Plate-Height of handle plate)	-
6.2.3 (Peg Stay - Thickness)	-
6.2.3 (Peg Stay )	-
6.3 (Top Hung Ventilator-Thickness of hinge)	-
6.3 (Top Hung Ventilator-Pin diameter)	-
6.3 (Top Hung Ventilator-Width of hinge)	-
4.3 (Designation)	-
9 (Glazing- No of glazing clip against each plate)	-
8 (Finish)	-
7.2 Table 2 (Position of Fixing Screws)	-
7.1 (Position of Holes)	-
6.3 (Top Hung Ventilator)	-
6.1.1.1 (Visual Inspection Test)	-
6.1.1.2 (Macro Examination)	-
6.1.1.3 (Micro Examination)	-
6.2 (Side Hung Shutter)	-
5 (Material-Rolled Steel Section)	-
5 (Material-Coupling Section)	-
5 (Material-Glass Panels)	-
5 (Material-Screws)	-

Partial

-
Complete

216

IS 7092 : Part 2 (1987)

Specification for aluminium alloy tube for irrigation purposes: Part 2 extruded tube (Second Revision)

Rs 11230/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.6.2 (Ultimate Tensile Strength- IS 2657)	-
Cl. 6.4 (Hydrostatic Pressure Test-Cl. 6.4)	-
Cl.7.1, Table 2 (Outside Diameter-)	-
Cl.7.1, Table 2 (Wall Thickness)	-
Cl. 7.2 (Length)	-
Cl.4 (Workmanship & Finish)	-

Partial

-
Excluding proof stress and Facility for chemical testing is not available

217

IS 6218 (2008)

Bicycle - Mudguards - Specification (First Revision)

- View breakup
Rs. 5400/- and material testing charges as per relevant referred ISs

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause-3 (Carbon)	-
Clause-3 (Sulphur)	-
Clause-3 (Phosphorus)	-
Clause-3 (Silicon)	-
Clause-3 (Nitrogen)	-
Cl 5.3(Mech) (The wraping of the mudguard shall lie within the limits )	-
Cl 5.1(Mech) (The paint shall not soften,peel off or show any change in colour after the test.)	-
Cl 4.3(Mech) (The painted part shall be free from wrinkles, blisters,unevenness,scratch marks and other injurious defects.)	-
Cl 4.2(Mech) (The mudguard shall be free from manufacturing defects and shall be chemically phosphated and and stove enamelled , spray painted or otherwise finished to give a glossy finish .)	-
Cl 4.1(Mech) (Thickness of steel strip)	-
Cl 4.1(Mech) (Depth of mudguard)	-
Cl 4.1(Mech) (Width of mudguard )	-
Cl 4(Mech) (Manufacture ,Workmanship ,& Finish )	-

Partial

-
Test facility for all test available but Separate sample of steel strip may be provided for thickness.

218

IS 455 (2015)

Portland slag cement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 Table 1 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
7 Table 1 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 Table 1 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 Table 1 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 Table 1 iii a (Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-
7 Table 1 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 Table 1 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
7 Table 1 i (Fineness IS 4031(Part 2))	-
6 - Table - 1 vii ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
6 - Table - 1 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 v (Loss on ignition - Cl 6.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 6.8 of IS 4032:1985)	-
6 - Table - 1 i (Insoluble residue - Cl 6.9 of IS 4032:1985)	-

Partial

-
Except Transverse Strength Test, sulphide Sulphur

219

IS 6003 (2010)

Indented Wire For--Prestressed Concrete ”

Rs.4110/- excl. relaxation test View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 6.1.2 (Weight)	-
Cl 7.1 (Tensile Test On UTM)	-
Cl 7.3 (Reverse Bend Test)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-
4.1.1 (Phosphorus %)	-
4.1.1 (Sulphur %)	-

Partial

-
Test Facility Complete for Chemical Except Stress relaxation test , Proof stress

220

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

Rs.750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2 (Tensile Test-1608:Part 1)	-
5.2 (Tensile Strength, Mpa)	-
5.2 (Elongation, %)	-
5.3 (Bend Test-1599)	-
8.2 (Width)	-
8.2 (Thickness)	-
7.1 (Freedom from defects)	-
9.1 (Finishing & Packing)	-

Complete

-
Test Facilty complete

221

IS 9890 (1981)

Specification for general purpose ball valves

Rs 4520/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (End connections)	-

Partial

-
Facility for chemical testing is not available

222

IS 4398 (1994)

Carbon - Chromium steel for the manufacture of balls, rollers and bearing races - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 ( Hardness-IS 1500: Pt 1)	-
Cl. 5.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

Partial

-
Microstructure, Inclusion, Decarburization, Cr, Ni, Mo, Cu, V and Ti.

223

IS 10086 (1982)

Specificaton for moulds for use in tests of cement and concrete

Rs 14700/- and Material testing charges as per relevan View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimension and tolerances of cylindrical moulds Table 3)	-
Cl 5.1 (Construction)	-
Cl 5.3 (Arangement for fastening / Clamping)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
5.1.1 (Construction)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
5.1.2 (Construction)	-
5.2.1 (Cube Mould)	-
5.2.2 (Cylindrical Mould (Fig.3))	-
5.2.3 (Beam Mould (Fig. 4))	-
5.2.4 (Bar Mould ( Fig. 5, 6, 7 & 8 ))	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and Tolerances of Cube Moulds Table 2)	-
4.1 (Dimension and tolerances of cylindrical moulds Table 3)	-
4.1 (Dimension and tolerances of beam moulds Table 4)	-
4.1 (Dimension and Tolerances of bar moulds Table 5)	-
2.1 (Types)	-
2.1 (Types)	-
2.1 (Types)	-
2.1 (Types)	-
2.1 (Types)	-
4.1 (Dimension and tolerances of cylindrical moulds Table 3)	-

Partial

-
Standard has been revised as IS 10086 : 2021 Except Shore Hardness, Dimension stability , Drop test , Facility for chemical testing is not available

224

IS 2052 (2009)

Compounded feeds for cattle - Specification (Fourth Revision)

Rs. 9210/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3 - Table 1 - i (Moisture - Cl 4 of IS 7874 (Part 1))	-
4.3 - Table 1 - ii (Crude protein (N x 6.25) - Cl 5 of IS 7874 (Part 1))	-
4.3 - Table 1 - iii (Crude fat - Cl 7 of IS 7874 (Part 1))	-
4.3 - Table 1 - iv (Crude fibre - Cl 8 of IS 7874 (Part 1))	-
4.3 - Table 1 - v (Acid insoluble ash - Cl 10 of IS 7874 (Part 1))	-
4.3 - Table 2 - i (Salt (as NaCl) - Cl 4 of IS 7874 (Part 2))	-
4.3 - Table 2 - ii (Calcium (as Ca) - IS 13433 (Part 1 / Part 2))	-
4.3 - Table 2 - iii (Total Phosphorus - IS 14828)	-
4.1 (Description - The feed shall be free from harmful constituents, metallic pieces and adulterants. The feed shall also be free from fungal growth and insect infestation. And from fermented . musty, rancid or any other objectionable odour)	-

Partial

-
Except Urea, Vitamin A,D, E, Aflatoxin and Cadmium, available phosphorous

225

IS 15911 (2010)

Structural steel (Ordinary Quality) - Specification

E 165 ,E 170 , E 215

Rs 6750/- For elements other than Table-1: Rs 1004/- pe View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1, 5.1, 8.1 & 8.2 (Carbon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Sulphur: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Silicon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Nitrogen: Relevant parts of IS 228 or any other established instrumental/chemical method)	-

Partial

-
Except Microalloys , Al,Cu

226

IS 8783 : Part 4 : Sec 3 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for individual wires: Sec 3 polyester and polypropylene insulated winding wires (First Revision)

Rs.8700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-
6.1 (The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-
6.1 (a) Reference to this Indian Standard;)	-
6.1 (c) Size of conductor / maximum overall diameter,)	-
6.1 (d) Length of conductor on spool / reel /coil;)	-
6.1 (e) Number of lengths onspool / reel / coil (if more than one);)	-
6.1 (f) Country of Manufacturer)	-
6.1 (g) Year of Manufacture.)	-
6.2 (BIS Certification Mark)	-
4 (i) Material)	-
5 (ii) Diameter [mm] Seperate wire:)	-
5 (ii) Diameter [mm] Wire taken from cable:)	-
5 (iii) Annealing test [Percentage] on Seperate wire:)	-
5 (iii) Annealing test [Percentage] on Wire taken from cable:)	-
5 (d) Resistance test [Ohm/km corrected to 20°c)	-
4.1, table 1 & 2 (a) Thickness of Polyster (mm))	-
4.1, table 1 & 3 (b) Thickness of Polypropylene (mm))	-
4.1, table 1 & 4 (c) Total thickness of Insulation(mm))	-
4.2 (Application of insulation)	-
4.3 (Colour of Insuation)	-
4.4 (Overall diameter (mm))	-
4 (Before ageing Tensile strength [N/mm²])	-
4 (Before ageing Elongation at break [Percentage])	-
4 (After ageing Tensile strength [N/mm²])	-
4 (Variation on tensile strangth [Percentage])	-
4 (After ageing Elongation at break [Percentage])	-
4 (Variation on elongation at break [Percentage])	-
4 (Shrinkage test [Percentage])	-
4 (After Shrinkage Cracks found.)	-
4.1 (Water absorption test [Gravimetric] [mg/cm²])	-
4.1 (Hot Deformation test [depth of indentation) [Percentage])	-
4.1 (Heat Shock Test - No cracks found)	-
4.1 (Insulation Resistance test [ohm-cm] At 27 ºC)	-
4.1 ([Insulation Resistance test [ohm-cm] At 90 ºC)	-
4.5 (High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-
5 (The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-
6 (The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-
6 (a) Reference to this Indian Standard;)	-
6 (c) Size of conductor / maximum overall diameter,)	-
6 (d) Length of conductor on spool / reel /coil;)	-
6 (e) Number of lengths onspool / reel / coil (if more than one);)	-
6 (f) Country of Manufacturer Marking)	-
6 (g) Year of Manufacture.)	-
6.2 (BIS Certification Mark)	-
4 (i) Material)	-
4 (ii) Diameter [mm] Seperate wire:)	-
4 (ii) Diameter [mm] Wire taken from cable)	-
4 (iii) Annealing test [Percentage] on Seperate wire:)	-
4 ([iii) Annealing test [Percentage] on Wire taken from cable:)	-
4 (d) Resistance test [Ohm/km corrected to 20°c])	-
4 (a) Thickness of Polyster (mm))	-
4 (b) Thickness of Polypropylene (mm))	-
4 (c) Total thickness of Insulation(mm))	-
4.2 (Application of insulation)	-
4 (Colour of Insuation)	-
4 (Overall diameter (mm))	-
4 (Before ageing Tensile strength [N/mm²])	-
4 (Before ageing Elongation at break [Percentage])	-
4 (After ageing Tensile strength [N/mm²])	-
4 (Variation on tensile strangth [Percentage])	-
4 (After ageing Elongation at break [Percentage])	-
4 (Variation on elongation at break [Percentage])	-
4 (Shrinkage test [Percentage])	-
4 (After Shrinkage Cracks found.)	-
4 (Water absorption test [Gravimetric] [mg/cm²])	-
4 (Hot Deformation test [depth of indentation) [Percentage])	-
4 (Heat Shock Test - No cracks found Physical)	-
4 (High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-
4 (Insulation Resistance test [ohm-cm] At 27 ºC)	-
4 (Insulation Resistance test [ohm-cm] At 90 ºC)	-

Complete

-
Test facility is complete

227

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

Rs 5100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
7.1 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
8.1.1 Table 1 (Tensile Strength- IS 1608(1))	-
8.1.1 Table 1 (Yield Strength- IS 1608)	-
8.1.1 Table 1 (Elongation Percent- IS 1608)	-
8.2 (Drift Expansion Test- IS 2335)	-
8.3 (Flattening Test- IS 2328)	-
9.1 Table 2 (Outside Diameter)	-
9.1 Table 2 (Thickness)	-
9.1 Table 2 (Mass)	-
10 (Hardness)	-
13.1.1 (Ovality)	-
13.1.2 (Eccentricity)	-
15.1 (Straightness)	-
16.1 (Length)	-

Complete

-
Test facility is complete

228

IS 2507 (1975)

Specification for cold - rolled steel strips for springs (First Revision)

Rs .6000/- Gr 1 to Gr 9 View breakup
Rs.3900/- for Gr.10, Rs.4500/- for Gr.11

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Carbon- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Sulphur- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Silicon- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Manganese- Appropriate parts of IS 228.)	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1 (Phosphorus- Appropriate parts of IS 228.)	-
7 (Rolling Tolerances)	-
10 (Physical properties(optional))	-
5 (FREEDOM FROM DEFECTS)	-

Partial

-
Decarburization, Grade 10(Except Cr and V), microalloys

229

IS 8931 (1993)

copper alloy fancy single taps, combination tap assembly and stop valves for water services

Rs 3600/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.6 (Screw Threads)	-
Cl 6.7 (Waterway)	-
Cl 6.9 (Body Seat)	-
Cl 7.3 (Bonnet Assembly)	-
Cl 8 (Finish)	-

Partial

-
Standard has been revised as IS 8931 : 2021 Except Performance test, water efficiency rating and Endurance test, Facility for chemical testing is not available

230

IS 2029 (1998)

Ring wrenches (Spanners) - Specification (Fourth Revision)

Rs.3700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3, Table-1 (Dimensions- s1)	-
3, Table-1 (Dimensions- s2)	-
3, Table-1 (Dimensions- a)	-
3, Table-1 (Dimensions- b1)	-
3, Table-1 (Dimensions- b2)	-
3, Table-1 (Dimensions- L)	-
6 (Workmanship and Finish)	-
7 (Designation)	-
Cl.4 (CARBON)	-
Cl.4 (SULPHUR)	-
Cl.4 (PHOSPHURS)	-
Cl.4 (MANGANESE)	-
Cl.4 (SILICON)	-

Partial

-
Excluding Torque test, Micro alloying elements

231

IS 2721 (2003)

Galvanized steel chain link fence fabric - Specification (Second Revision)

- View breakup
Rs.5950/- (for wire below 5 mm Dia), Rs.6910/- (for wires above 5 mm Dia) and Material testing charges as per relevant referred Iss

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.5 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.8 (Chain link fence fabric(Mass of zinc coating)- IS 6745)	-
Cl.8 (Chain link fence fabric (Uniformity of Zinc coating)-IS 2633)	-
Cl.9.2 (Mesh wire (Mass of zinc coating)- IS 6745)	-
Cl.9.2 (Mesh Wire (Uniformity of Zinc coating)-IS 2633)	-
Cl.6.1, 6.2, Table 1 (Mesh Size)	-
Cl.6.3, Table 1 (Width of the fabric)	-
Cl.6.3, Table 1 (Length of the fabric)	-
Cl.6.1, 6.2, Table 1 (Nominal Dia of Mesh wire)	-
Cl. 7.2 and Table 1 (Line Wire (Diameter))	-
Cl. 7.2 and Table 1 (Line Wire (Number of wires))	-
Cl.9.1.1 (Tensile test of mesh and line wires- IS 1608)	-
Cl.9.1.2 (Wrapping test of mesh and line wires-IS 1755)	-
Cl.9.1.3 (Twist test of mesh and line wires-IS 1717)	-
Cl.9.1.4 (Bend test of mesh and line wires- IS 1608)	-

Complete

-
Test facility is complete

232

IS 4223 (1975)

Steel Wire For Umbrella Ribs

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8,9 (Sizes and Tolerances - IS 4223)	-
10.1, Table 1 (Mechanical ptoperties - IS 1608(Pt -1))	-
10.2 (Torsion Test - IS 1717)	-
7 (Freedom rom defects , IS 4223)	-
10.3 (Reverse Bend Test--IS 1716)	-
Cl 6.1 (Sulphur- Appropriate parts of IS 228.)	-
Cl 6.1 (Phosphorus- Appropriate parts of IS 228.)	-
Cl 6.1 (Sulphur- Appropriate parts of IS 228.)	-
Cl 6.1 (Phosphorus- Appropriate parts of IS 228.)	-

Complete

-
Test facility is complete

233

IS 2028 (2004)

Open jaw wrenches (Spanners) - Specification (Fijih Revision)

Rs.3700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Dimensions- a)	-
3.1 (Dimensions- b)	-
3.1 (Dimensions- l)	-
3.2, 3.3, 3.4 (Dimensions- a)	-
3.2, 3.3, 3.4 (Dimensions- b1)	-
3.2, 3.3, 3.4 (Dimensions- b2)	-
3.2, 3.3, 3.4 (Dimensions- l)	-
3.2, 3.3, 3.4 (Dimensions- b2)	-
6 (Workmanship And Finish)	-

Partial

-
Excluding Torque test, Micro alloying elements

234

IS 9523 (2000)

Ductile iron fittings for pressure pipes for water, gas and sewage - Specification (First Revision)

Rs.7245.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Thickness)	-
Cl 6 & Table 4,5,6&7 (Design & Tolerance)	-
Cl 9 (Tensile Test & Hardness Test)	-
Cl 10 (Hydrostatic Test)	-
Cl 11 (Nominal Diameter, Ovality, Dimensions, No. Of Holes & Bolt Sizes)	-
Cl 13 (Coating)	-

Partial

-
1 coated, 1 uncoated and separate sample for tensile and hardness test are required Except HST for DN above 300 mm

235

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Rs. 33750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
20.13 (Test for Halogen Acid Gas Evolution)	-
4.1 (CONDUCTOR)	-
4.1.1 (CONDUCTOR)	-
5 (INSULATION)	-
6 (SCREENING)	-
6.1.1 (SCREENING : - Non-metallic — Semiconducting Compound)	-
6.1.2 (SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-
7 (FILLERS AND INNER SHEATH)	-
8.1 (ARMOURING)	-
8.2 (ARMOURING)	-
9 (OUTER SHEATH )	-
10.1 (CONDUCTOR)	-
10.2 (CONDUCTOR)	-
11 (CONDUCTOR SCREENING)	-
12.1 (INSULATION)	-
12.2 (INSULATION : Thickness of Insulation)	-
12.3 (INSULATION : Tolerance on Thickness of Insulation)	-
12.4 (Eccentricity and Ovality)	-
12.5 (INSULATION : Application of Insulation)	-
13.1 (INSULATION SCREENING)	-
13.2 (INSULATION SCREENING)	-
13.3 (INSULATION SCREENING)	-
13.4 (INSULATION SCREENING)	-
14.1 (CORE IDENTIFICATION)	-
14.1.1 (CORE IDENTIFICATION)	-
15.1 (LAVING UP OF CORES)	-
16.1 (INNER SHEATH (COMMON COVERING))	-
16.2 (INNER SHEATH (COMMON COVERING))	-
16.2.1 (INNER SHEATH (COMMON COVERING))	-
16.3 (INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-
16.3.1 (INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-
17.1 (ARMOURING : Application )	-
17.1.1 (ARMOURING )	-
17.1.2 (ARMOURING )	-
17.1.3 (ARMOURING )	-
17.2 (ARMOURING : Type of armour )	-
17.2.1 (ARMOURING : Type of armour )	-
17.2 (ARMOURING : Coverage )	-
17.3 (ARMOURING : Dimension )	-
17.4 (ARMOURING : Joints)	-
16.4 (ARMOURING : Resistance)	-
18.1 (OUTER SHEATH)	-
18.2 (OUTER SHEATH: Colour)	-
18.3 (Thicknes of outer sheath : average )	-
18.3 (Thicknes of outer sheath : minimum )	-
19.1 i) a) (Annealing test (for copper))	-
19.1 i) b) (Tensile test (for aluminium) - Before stranding )	-
19.1 i) b) (Tensile test (for aluminium) - After stranding )	-
19.1 i) c) (Wrapping test ( for aluminium))	-
19.1 i) d) (Resistance test - Main conductor )	-
19.1 i) d) (Resistance test - Neutral conductor )	-
19.1 iii) a) (Phyaical tests for insulation : Tensile Test)	-
19.1 iii) a) (Phyaical tests for insulation : Elongation )	-
19.1 iii) b) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
19.1 iii) b) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
19.1 iii) b) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
19.1 iii) d) (Phyaical tests for insulation : Hot set )	-
19.1 iii) d) (Phyaical tests for insulation : Permanent set )	-
19.1 iii) e) (Phyaical tests for insulation : Shrinkage )	-
19.1 iii) e) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
19.1 iii) f) (Insulation: Waterabsorption(gravimetric))	-
19.1 v) b) (Volume resistivity)	-
19.1 vi) a) (Physical tests for outer sheath : Tensile stregth )	-
19.1 vi) a) (Physical tests for outer sheath : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
19.1 iii) a) (Phyaical tests for insulation : Tensile Test)	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
19.1 vi) d) (Sheath : Hot deformation)	-
19.1 vi) e) (Loss of massIn air oven)	-
19.1 vi) f) (Sheath : Heat shock test)	-
19.1 vi) g) (Sheath : Thermalstability)	-
20.7 (High voltage test)	-
20.8 (Flammability test)	-
20.1 (Oxygen Index Test)	-
20.11 (Flame Retardance Test on Single Cables)	-
20.12 (Flame Retardance Test on Bunched Cables)	-
20.14 ( Test for Smoke Density)	-
20.15 (Temperature Index)	-
21.1 (IDENTIFICATION : Manufacturer's Identification)	-
21.2 (IDENTIFICATION : Cable Identification)	-
21.3 (IDENTIFICATION : Cable Code)	-

Partial

-
Test facility is complete for Chemical Except Cl.20.9 Ageing Test on complete cable, Cl.20.2 Partial discharge, impulse , Cl.20.7 HVT(above 10 kV), Cl.20.3 bending test ,Cl.20.4 Dielectric power factor test ,Cl.20.5 Heat Cycle test,Cl.20.6 Impulse withstand test

236

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

Rs.5400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Diameter, Ovality & Weight)	-
Cl 9 (UTM & HBW)	-
Cl 7 (Workmanship)	-
6.1, 6.2 (carbon)	-
6.1, 6.2 (sulphur)	-
6.1, 6.2 (silicon )	-
6.1, 6.2 (manganese)	-
6.1, 6.2 (phosphorus)	-

Partial

-
Excluding Grain size, Microstructure,Microalloying Elements

237

IS 1825 (1983)

Specification for aluminium alloy milk cans (Second Revision)

Rs 4800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (a) Rated Capacity)	-
8 (b) Point of Capacity)	-
8 (c) Batch OR Code No.)	-
8 (d) BIS Mark)	-
8 (e) Manufacturer's Trade Mark )	-
2 (Capacity)	-
4 Fig. 1 (Dimensions & Shape)	-
4 Fig. 1 (A)	-
4 Fig. 1 (B)	-
4 Fig. 1 (C )	-
4 Fig. 1 (D)	-
4 Fig. 1 (E)	-
4 Fig. 1 (F)	-
4 Fig. 1 (G)	-
4 Fig. 1 (H)	-
4 Fig. 1 (BOTTOM BAND)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Drain Holes )	-
4 Fig. 1 (HANDLE )	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (LID)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Hole Dia 8 ,2 holes)	-
4 Fig. 1 (Hole Dia 12, 3 holes)	-
5 (a)Transport cans shall consist of a body, bottom band)	-
5 (lid and handles.)	-
5 (b)Minimum Thickness(in mm))	-
5 (i) Body and Neck)	-
5 (ii) Bottom)	-
5 (iii) Lid (Inner))	-
5 (iv) Lid (Outer))	-
5 (c) Mode of Shaping)	-
5 (i) If the thickness at shoulder is less than 2.5 mm a )	-
5 (reinforcement ring of 2 mm thickness shall be provided.)	-
5 (ii) Brinell Hardness 85 HB Min.)	-
5 (d) BOTTOM BAND- It shall be shrunk fit with a )	-
5 (proper locking arrangement on the body. This shall)	-
5 (be followed by brazing or welding all round.)	-
5 (e) HANDLES (as per Cl 5.6))	-
5 (f) SEALING LUG (as per Cl 5.7))	-
5 (g)Workmanship and Finish- All brazing or welding shall )	-
5 (be sound , free of porosity and shall be finished smooth .)	-
5 (h) Mass 6.5 Kg. Min.)	-
7 (i) Air Pressure Test (Cl 7.1))	-
7 (ii) Drop Test (Cl 7.2))	-
7 (iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-

Partial

-
Test facility is complete, Facility for chemical testing is not available

238

IS 4224 (1972)

Specification for steel wire for staples, pins and clips (First Revision)

525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Sizes and Tolerances - IS 4224)	-
7.1 (Tensile Test - IS 1608(Pt -1))	-
4 (Freedom from defects , IS 4224)	-
7.2 (Reverse Bend Test--IS 1716)	-

Complete

-
Test facility is complete

239

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
16.13 (Test for Halogen Acid Gas Evolution)	-
3 (CONDUCTOR: MATERIALS)	-
4 (INSULATION : MATERIALS)	-
5.1 (FILLER AND INNER SHEATH)	-
5.2 (FILLER AND INNER SHEATH)	-
6 (ARMOURING)	-
7 (OUTER SHEATH)	-
8.1 (CONDUCTOR: CONSTRUCTION)	-
8.2 (PROTECTIVE BARRIER)	-
8.3 (SIZE OF NEUTRAL CONDUCTOR)	-
9.1 (Insulation Applied by extrusicn)	-
9.2 (Thickness of Insulation - Average)	-
9.3 (Thickness of Insulation - Minimum)	-
9.4 (Application of Insulation)	-
10.1 (Core Identification)	-
10.2 (Core Identification- Neutral)	-
10.3 (Core Identification by number )	-
10.4 (Core Identification by number - Neutral )	-
11 (LAVING UP OF CORES)	-
12.1 & 12.2 (Inner sheath : Application)	-
12.3 (Thickness of Inner Sheath)	-
13.1 (Armouring: Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (Armouring: Direction of Lay )	-
13.2 (Type of armour )	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (Armour: Joint)	-
13.5 (Armouring : Resistance Test)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (Outer Sheath : Application)	-
14.2 (Colour of outer sheath)	-
14.3 (Thickness of outer sheath - AVERAGE)	-
14.3 (Thickness of outer sheath - minimum)	-
15.1 a) i) (Annealing Test ( For copper wire ) )	-
15.1 a) ii) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) ii) (Tensile test (for aluminium) - After stranding )	-
15.1 a) iii) (Wrapping test (for aluminium))	-
15.1 a) iv) (Resistance test - Neutral conductor)	-
15.1 a) iv) (Resistance test - Main conductor)	-
15.1 a) iv) (Resistance test - Neutral conductor)	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 e) v) (Sheath : Hot deformation)	-
15.1 e) vi) (Sheath : Heat shock test)	-
15.1 e) vii) (Sheath : Thermalstability)	-
15.1 f) (INSULATION RESISTANCE TEST : Volume resistivity )	-
16.2 (HIGH VOLTAGE TEST )	-
16.3 (FLAMMABILITY TEST : Period of Burning )	-
16.2 (HIGH VOLTAGE TEST )	-
16.3 (FLAMMABILITY TEST : Period of Burning )	-
16.3 (FLAMMABILITY TEST : Unaffected length )	-
16.9 (Oxygen Index Test)	-
16.1 (Flame Retardance Test on Single Cables)	-
16.11 (Flame Retardance Test on Bunched Cables)	-
16.14 (Temperature Index)	-
17.1 (Manufacturer'. identification)	-
17.2 (cable Indentification )	-
17.3 (cable Code )	-

Partial

-
Test facility is complete

240

IS 651 (2007)

Glazed stoneware pipes and fittings - Specification (Sixth Revision)

Rs. 6850/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 7.4 (Acid Resistance Test)	-
Clause 7.5 (Alkali Resistance Test)	-
7.2 (Hydraulic Test)	-
7.3 (Absorption Test)	-
11.1-Table 1 ( Mean Thickness of Barrel and of Socket)	-
10.1-Table 1 (INTERNAL DIAMETER)	-
14-Table 1 (Internal Depth of Socket)	-
14-Table 2 (Excess Shoulder Measurment)	-
14-Table 3 (Length of Grooving of Spigot)	-
12.2 (STRAIGHTNESS OF BARRELS OR STRAIGHT AND TAPER PIPES-Length of Junction)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-Internal Diameter)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-angle)	-
13.1-Table 6 (Dimensions of One-Eighth Taper Bends-D)	-
17-Table 10 (Dimensions of Channel Interceptors-A)	-
17-Table 10 (Dimensions of Channel Interceptors-G)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-Type)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-A)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-G)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-F')	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-F)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-E)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-D)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-Size)	-
14 (The interior of the sockets shall be conical, having a minimum taper)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-r)	-
13.1-Table 5 (Dimension of One-Quarter Taper Bends-r)	-
17-Table 10 (Dimensions of Channel Interceptors-C)	-

Partial

-
Test facility is complete for Chemical Except HST and compression test For size above 300 mm

Bureau of Indian Standards

The National Standards Body of India

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrol@bis.gov.in

Scope List