BIS - LIMS (Laboratory Information Management System)

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrolsample@bis.gov.in

Scope List

Reset

306 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

241

IS 9523 (2000)

Ductile iron fittings for pressure pipes for water, gas and sewage - Specification (First Revision)

Rs.7245.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5 (Thickness)	-
Cl 6 & Table 4,5,6&7 (Design & Tolerance)	-
Cl 9 (Tensile Test & Hardness Test)	-
Cl 10 (Hydrostatic Test)	-
Cl 11 (Nominal Diameter, Ovality, Dimensions, No. Of Holes & Bolt Sizes)	-
Cl 13 (Coating)	-

-
1 coated, 1 uncoated and separate sample for tensile and hardness test are required Except HST for DN above 300 mm

242

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Rs. 33750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
20.13 (Test for Halogen Acid Gas Evolution)	-
4.1 (CONDUCTOR)	-
4.1.1 (CONDUCTOR)	-
5 (INSULATION)	-
6 (SCREENING)	-
6.1.1 (SCREENING : - Non-metallic — Semiconducting Compound)	-
6.1.2 (SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-
7 (FILLERS AND INNER SHEATH)	-
8.1 (ARMOURING)	-
8.2 (ARMOURING)	-
9 (OUTER SHEATH )	-
10.1 (CONDUCTOR)	-
10.2 (CONDUCTOR)	-
11 (CONDUCTOR SCREENING)	-
12.1 (INSULATION)	-
12.2 (INSULATION : Thickness of Insulation)	-
12.3 (INSULATION : Tolerance on Thickness of Insulation)	-
12.4 (Eccentricity and Ovality)	-
12.5 (INSULATION : Application of Insulation)	-
13.1 (INSULATION SCREENING)	-
13.2 (INSULATION SCREENING)	-
13.3 (INSULATION SCREENING)	-
13.4 (INSULATION SCREENING)	-
14.1 (CORE IDENTIFICATION)	-
14.1.1 (CORE IDENTIFICATION)	-
15.1 (LAVING UP OF CORES)	-
16.1 (INNER SHEATH (COMMON COVERING))	-
16.2 (INNER SHEATH (COMMON COVERING))	-
16.2.1 (INNER SHEATH (COMMON COVERING))	-
16.3 (INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-
16.3.1 (INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-
17.1 (ARMOURING : Application )	-
17.1.1 (ARMOURING )	-
17.1.2 (ARMOURING )	-
17.1.3 (ARMOURING )	-
17.2 (ARMOURING : Type of armour )	-
17.2.1 (ARMOURING : Type of armour )	-
17.2 (ARMOURING : Coverage )	-
17.3 (ARMOURING : Dimension )	-
17.4 (ARMOURING : Joints)	-
16.4 (ARMOURING : Resistance)	-
18.1 (OUTER SHEATH)	-
18.2 (OUTER SHEATH: Colour)	-
18.3 (Thicknes of outer sheath : average )	-
18.3 (Thicknes of outer sheath : minimum )	-
19.1 i) a) (Annealing test (for copper))	-
19.1 i) b) (Tensile test (for aluminium) - Before stranding )	-
19.1 i) b) (Tensile test (for aluminium) - After stranding )	-
19.1 i) c) (Wrapping test ( for aluminium))	-
19.1 i) d) (Resistance test - Main conductor )	-
19.1 i) d) (Resistance test - Neutral conductor )	-
19.1 iii) a) (Phyaical tests for insulation : Tensile Test)	-
19.1 iii) a) (Phyaical tests for insulation : Elongation )	-
19.1 iii) b) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
19.1 iii) b) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
19.1 iii) b) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
19.1 iii) d) (Phyaical tests for insulation : Hot set )	-
19.1 iii) d) (Phyaical tests for insulation : Permanent set )	-
19.1 iii) e) (Phyaical tests for insulation : Shrinkage )	-
19.1 iii) e) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
19.1 iii) f) (Insulation: Waterabsorption(gravimetric))	-
19.1 v) b) (Volume resistivity)	-
19.1 vi) a) (Physical tests for outer sheath : Tensile stregth )	-
19.1 vi) a) (Physical tests for outer sheath : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
19.1 iii) a) (Phyaical tests for insulation : Tensile Test)	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
19.1 vi) b) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
19.1 vi) b) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage )	-
19.1 vi) c) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
19.1 vi) d) (Sheath : Hot deformation)	-
19.1 vi) e) (Loss of massIn air oven)	-
19.1 vi) f) (Sheath : Heat shock test)	-
19.1 vi) g) (Sheath : Thermalstability)	-
20.7 (High voltage test)	-
20.8 (Flammability test)	-
20.1 (Oxygen Index Test)	-
20.11 (Flame Retardance Test on Single Cables)	-
20.12 (Flame Retardance Test on Bunched Cables)	-
20.14 ( Test for Smoke Density)	-
20.15 (Temperature Index)	-
21.1 (IDENTIFICATION : Manufacturer's Identification)	-
21.2 (IDENTIFICATION : Cable Identification)	-
21.3 (IDENTIFICATION : Cable Code)	-
Cl.8 & 17 (Armouring : Tensile Strength)	-
Cl.8 & 17 (Armouring : Elongation)	-
Cl.8 & 17 (Armouring : Torsion Test (For Round Steel Wire Only))	-
Cl.8 & 17 (Armouring: Winding Test ( For formed steel wire only))	-
Cl.8 & 17 (Armouring : Application)	-
Cl.8 & 17 (Armouring : Uniformity of Zinc Coating)	-
Cl.8 & 17 (Armouring: Mass of Zinc Coating)	-
Cl.8 & 17 (Armouring : Resistivity Test)	-
Cl.8 & 17 (Armouring: Cold Impact Test (For outer Sheath))	-
Cl. 13.5.1 and Table 7 (Armouring: Resistance Test for Armouring (Other than Mining Cables))	-
Cl-20.16 (Amendment No-2) (Longitudinal Water Penetration Test)	-

-
Test facility is complete for Chemical Except Cl.20.9 Ageing Test on complete cable, Cl.20.2 Partial discharge, impulse , Cl.20.7 HVT(above 10 kV), Cl.20.3 bending test ,Cl.20.4 Dielectric power factor test ,Cl.20.5 Heat Cycle test,Cl.20.6 Impulse withstand test

243

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

Rs.5400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Diameter, Ovality & Weight)	-
Cl 9 (UTM & HBW)	-
Cl 7 (Workmanship)	-
6.1, 6.2 (carbon)	-
6.1, 6.2 (sulphur)	-
6.1, 6.2 (silicon )	-
6.1, 6.2 (manganese)	-
6.1, 6.2 (phosphorus)	-

-
Excluding Grain size, Microstructure,Microalloying Elements

244

IS 1825 (1983)

Specification for aluminium alloy milk cans (Second Revision)

Rs 4800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (a) Rated Capacity)	-
8 (b) Point of Capacity)	-
8 (c) Batch OR Code No.)	-
8 (d) BIS Mark)	-
8 (e) Manufacturer's Trade Mark )	-
2 (Capacity)	-
4 Fig. 1 (Dimensions & Shape)	-
4 Fig. 1 (A)	-
4 Fig. 1 (B)	-
4 Fig. 1 (C )	-
4 Fig. 1 (D)	-
4 Fig. 1 (E)	-
4 Fig. 1 (F)	-
4 Fig. 1 (G)	-
4 Fig. 1 (H)	-
4 Fig. 1 (BOTTOM BAND)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Drain Holes )	-
4 Fig. 1 (HANDLE )	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (LID)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Hole Dia 8 ,2 holes)	-
4 Fig. 1 (Hole Dia 12, 3 holes)	-
5 (a)Transport cans shall consist of a body, bottom band)	-
5 (lid and handles.)	-
5 (b)Minimum Thickness(in mm))	-
5 (i) Body and Neck)	-
5 (ii) Bottom)	-
5 (iii) Lid (Inner))	-
5 (iv) Lid (Outer))	-
5 (c) Mode of Shaping)	-
5 (i) If the thickness at shoulder is less than 2.5 mm a )	-
5 (reinforcement ring of 2 mm thickness shall be provided.)	-
5 (ii) Brinell Hardness 85 HB Min.)	-
5 (d) BOTTOM BAND- It shall be shrunk fit with a )	-
5 (proper locking arrangement on the body. This shall)	-
5 (be followed by brazing or welding all round.)	-
5 (e) HANDLES (as per Cl 5.6))	-
5 (f) SEALING LUG (as per Cl 5.7))	-
5 (g)Workmanship and Finish- All brazing or welding shall )	-
5 (be sound , free of porosity and shall be finished smooth .)	-
5 (h) Mass 6.5 Kg. Min.)	-
7 (i) Air Pressure Test (Cl 7.1))	-
7 (ii) Drop Test (Cl 7.2))	-
7 (iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-
Cl. 3.1,3.2,3.3 (Copper)	-
Cl. 3.1,3.2,3.3 (Manganese)	-
Cl. 3.1,3.2,3.3 (Silicon)	-
Cl. 3.1,3.2,3.3 (Iron)	-
Cl. 3.1,3.2,3.3 (Aluminium)	-
Cl. 3.1,3.2,3.3 (Magnesium)	-
Cl. 3.1,3.2,3.3 (Zinc)	-
Cl. 3.1,3.2,3.3 (Titanium)	-
Cl. 3.1,3.2,3.3 (Vanadium)	-
Cl. 3.1,3.2,3.3 (Chromium)	-

-
Test facility is complete,

245

IS 4224 (1972)

Specification for steel wire for staples, pins and clips (First Revision)

525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (Sizes and Tolerances - IS 4224)	-
7.1 (Tensile Test - IS 1608(Pt -1))	-
4 (Freedom from defects , IS 4224)	-
7.2 (Reverse Bend Test--IS 1716)	-

-
Test facility is complete

246

IS 651 (2007)

Glazed stoneware pipes and fittings - Specification (Sixth Revision)

Rs. 6850/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 7.4 (Acid Resistance Test)	-
Clause 7.5 (Alkali Resistance Test)	-
7.2 (Hydraulic Test)	-
7.3 (Absorption Test)	-
11.1-Table 1 ( Mean Thickness of Barrel and of Socket)	-
10.1-Table 1 (INTERNAL DIAMETER)	-
14-Table 1 (Internal Depth of Socket)	-
14-Table 2 (Excess Shoulder Measurment)	-
14-Table 3 (Length of Grooving of Spigot)	-
12.2 (STRAIGHTNESS OF BARRELS OR STRAIGHT AND TAPER PIPES-Length of Junction)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-Internal Diameter)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-angle)	-
13.1-Table 6 (Dimensions of One-Eighth Taper Bends-D)	-
17-Table 10 (Dimensions of Channel Interceptors-A)	-
17-Table 10 (Dimensions of Channel Interceptors-G)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-Type)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-A)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-G)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-F')	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-F)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-E)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-D)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-Size)	-
14 (The interior of the sockets shall be conical, having a minimum taper)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-r)	-
13.1-Table 5 (Dimension of One-Quarter Taper Bends-r)	-
17-Table 10 (Dimensions of Channel Interceptors-C)	-

-
Chemical- complete; Mechanical- complete except HST and compression test for sizes above 300 mm

247

IS 458 (2003)

Precast concrete pipes(With And Without Reinforcement) - Specification (Fourth Revision)

4200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (a) Identification)	-
5.1.1 (b) Date of cast )	-
5.1.1 (c) Date of test )	-
5.1.1 (d) i) Curing-when received dry the specimen shall be kept in water for 24 hr)	-
5.1.1 (ii) weight)	-
5.1.1 (iv) Cross-sectional area ( in mm2))	-
5.1.1 (v) Max. Load ( in kN) )	-
5.1.1 (vi) Compressive strength, N/mm2 )	-
5.1.1 (vii) Fracture)	-
5.1.1 (viii) Individual variation of average )	-

-
Standard has been revised as IS 458 : 2021 Except three edge load and HST, Split tesnsile and compressive strength upto 1000KN load-

248

IS 624 (2003)

Bicycles - Rims - Specification (Fourth Revision)

2850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (FINISH)	-
3.2 (SHAPES AND DIMENSIONS)	-
9 (COMPRESSION TEST)	-
7 (chem) (FINISH)	-

-
Except dimensions clause 3.2 & 3.2.1 Circumference, finish test facility only for Ni/Cr coating thickness

249

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

Rs 3000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 5.1.2 (Weight)	-
Cl 6.1 (Tensile Test On UTM)	-
Cl 6.3 (Tensile Test On UTM)	-
3.1.1 (PHOSPHORUS)	-
3.1.1 (SULPHUR)	-
Cl. 7.5 (Ductility/ Reverse Bend Test)	-

-
Test facility is complete for Chemical Except Proof Stress

250

IS 1729 (2002)

Cast iron/ductile iron drainage pipes and pipe fittings for over ground non-pressure pipeline socket and spigot series (Second Revision)

Rs. 2850/- and testing charges as per referred Iss View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Tensile Strrngth - IS1608(Pt-1))	-
5.1 (Elongation - IS 1608(Pt-1))	-
5.4 (Hardness- IS 1500)	-
7 (Leakage Test - IS 1729)	-
8.2-Table 1 to 32 (Dimension, a)	-
8.2-Table 1 to 32 (Dimension, b)	-
8.2-Table 1 to 32 (Dimension, c)	-
8.2-Table 1 to 32 (Dimension, d)	-
8.2-Table 1 to 32 (Dimension, e)	-
8.2-Table 1 to 32 (Dimension, f)	-
8.2-Table 1 to 32 (Dimension, g)	-
8.2-Table 1 to 32 (Dimension, h)	-
8.2-Table 1 to 32 (Dimension, i)	-
8.2-Table 1 to 32 (Dimension, j)	-
8.2-Table 1 to 32 (Dimension, k)	-
8.2-Table 1 to 32 (Dimension, l)	-
8.2-Table 1 to 32 (Dimension, m)	-
8.2-Table 1 to 32 (Dimension, n)	-
8.2-Table 1 to 32 (Dimension, p)	-
8.2-Table 1 to 32 (Dimension, q)	-
8.2-Table 1 to 32 (Dimension, r)	-
8.2-Table 1 to 32 (Dimension, r1)	-
8.2-Table 1 to 32 (Dimension, r2)	-
8.2-Table 1 to 32 (Dimension, s)	-
8.2-Table 1 to 32 (Dimension, t)	-
11 (Coating Test at 65degree Celcius )	-
11 (Coating Test at 0degree Celcius)	-
5.3 (Casting Defects)	-

-
Test facility is complete and Standard has been revised as IS 1729 : 2023 Facility for chemical testing is not available

251

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

Rs.8420/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 i (Insoluble residue - Cl 7.4 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 7.2 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-
6 - Table - 1 v (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 - Table - 1 vi ( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-
7 -Table 2- i (Fineness 4031 Part 2)	-
7 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
7 -Table 2- ii- a (Expansion after aeration - 4031 Part 3)	-
7 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
7 -Table 2- ii- b (Expansion after aeration- 4031 Part 3)	-
7 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
7 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
7 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
7 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
7 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-
7 -Table 2- vi (Drying Shrinkage- IS 4031 Part 10)	-

-
Test facility is complete for Chemical Except Transverse Strength Test

252

IS 2255 (1977)

Specification for mild steel wire rod for the manufacture of machine screws (By Cold Heading Process) (Second Revision)

Rs. 600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Sizes and tolernces)	-
8 (FREEDOM FROM DEFECTS)	-

-
Test facility is complete for Chemical,Tensile test,Microaalloying Element

253

IS 2266 (2024)

STEEL WIRE ROPES FOR GENERAL ENGINEERING PURPOSE - SPECIFICATION (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-5 (Minimum breaking force)	-
Cl-6 of IS 1835 (Manganese)	-
Cl-6 of IS 1835, (Carban)	-
Cl-6 of IS 1835 (Silicon)	-
Cl-6 of IS 1835 (Sulphur, Max)	-
Cl-6 of IS 1835 (Phosphorus, Max)	-

-
Special Tensile Testing machine of more than 1000kN capacity is required Except "Tensile test". Test Facility is not available for clause 8.1 and test facility available only for chemical composition (except Microalloying Elements) and galvanizing for clause 8.2 as per IS 6594.

254

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

Rs7935/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (S)	-
4 (P)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Hard Core)	-
11 (a) Size)	-
11 (b) Construction)	-
11 (c) tensile designation)	-
11 (d) lay)	-
11 (e) coating)	-
11 (f) length)	-
11 ( g) mass)	-
11 (h) manufacturer's name or trade mark)	-
11 (i) lot number along with the order number)	-
11 (j) BIS Standards Mark)	-
5 (a) Grade)	-
5 (b) Tensile Grade)	-
6 (a) Lay)	-
6 (b) Construction)	-
7 (Freedom from defects)	-
9 (a) Tensile)	-
9 (b) Elongation)	-
9 (c) Galvanizing Test)	-
11 (a) Size)	-
11 (b) Construction)	-

-
Chemical - complete Mechanical Complete except except Tensile test

255

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Rs 3900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 3.1.1 (Sulphur)	-
Clause 3.1.1 (Phosphorus)	-
Cl 5 & 6 (Diameter)	-
Cl 7 (UTM)	-
Cl 4.1 (Workmanship)	-
Cl 8.3 (Bending To Both Side At 90°, Then Straight)	-
Clause 7.1 (Ultimate Tensile Stress)	-

-
Except Microalloying Elements Except Proof Stress

256

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

Rs 2100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.2 (Diameter & Ovality)	-
Cl 6.2 (Weight)	-
Cl 8.2 (Bend test)	-
Cl 5.1 (Workmanship)	-
Cl 9.3 (Press)	-
Clause -4, 4.1 ( CARBON)	-
Clause -4, 4.1 (SULPHUR)	-
Clause -4, 4.1 (SILICON)	-
Clause -4, 4.1 (MANGANESE)	-
Clause -4, 4.1 (PHOSPHURS)	-
Clause -4, 4.1 (NITROGEN)	-
Cl 6.1 (Diameter)	-
Cl 8.1 (ultimate tensile stress, yield stress and percentage elongation)	-
Cl 8 (Physical Requirements)	-
Clause -4, 4.1 ( ALUMINIUM)	-
Clause -4, 4.1 (Nickel)	-
Clause -4, 4.1 (Chromium)	-
Clause -4, 4.1 (Molybdenum)	-
Clause -4, 4.1 (NIOBIUM)	-
Clause -4, 4.2 (VANADIUM)	-
Clause -4, 4.3 (TITANIUM)	-

-
-

257

IS 210 (2009)

Grey iron castings - Specification (First Revision)

Rs.2700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
13 (SIZE OF TEST BARS-Diameter)	-
13 (SIZE OF TEST BARS-Length)	-
15, Table 3 (TENSIL.E TEST- IS 1608 Part1 )	-
16, Table 3 (Hardness Test)	-
6 (Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-
6 (Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-
7.1 (WORKMANSHIP AND FINISH)	-
10.1 (FREEDOM FROM DEFECTS)	-
10.2 (FREEDOM FROM DEFECTS)	-
6 (Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-

-
Test facility available for Mechanical tests only, Excluding Transverse Test, Microstructure and Hydrostatic Test above 300mm. Since the composition of cast iron shall be left to the discretion of the manufacture, as such element to be tested with specified requirement and tolerances if any may please be declared with method of testing.Sample size 5 pcs of 5X5 cm having dia > 3mm and thickness > 0.8 mm.

258

IS 3431 (1982)

Specification for steel for the manufacture of volute helical and laminated springs for automotive suspension (Second Revision)

Rs 1800/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8,Table 4 (Mechanical properties - IS 3431)	-
12 (Straightness)	-
13, Table 5&Table 6 (Dimensions and Tolerance)	-
10 (Freedom from defects)	-
Cl. 2.1, 5.1 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 2.1, 5.1 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Except Cr, V and Micro alloying elements

259

IS 1239 : Part 2 (2011)

Steel tubes, tubulars and other steel fittings - Specification: Part 2 steel pipe fittings (Fifth Revision)

3400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Chemical Composition - Sulphur - Laddle Analysis IS 228)	-
7.1 (Chemical Composition - Phosphorus - Laddle Analysis IS 228)	-
8.1-Table 1 ( DIMENSIONS OF TUBULARS-Pieces )	-
8.1-Table 1 ( DIMENSIONS OF TUBULARS-Pieces-Approximate Standard Length(A) )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-A )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-B )	-
8.2-Table-2 ( DIMENSIONS OF TUBULARS-Nipples-C )	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-A)	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-B)	-
8.3.1-Table 3 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-C)	-
8.3.2 (DIMENSIONS OF TUBULARS-Longscrews (Connectors))	-
8.3.2 (DIMENSIONS OF TUBULARS-Longscrews (Connectors)-The face of the back nut angle)	-
8.4.1 -Table 4 (Bends and springs)	-
8.4.1 -Table 4 (Bends and springs-A)	-
8.4.1 -Table 4 (Bends and springs-B)	-
8.4.1 -Table 4 (Bends and springs-C)	-
8.4.1 -Table 4 (Bends and springs-D)	-
8.4.1 -Table 4 (Bends and springs-E)	-
8.5-Table 5 ( Return Bends-A)	-
8.5-Table 5 ( Return Bends-B)	-
8.6 -Table 6 (Sockets-A)	-
8.6 -Table 6 (Sockets-B)	-
8.6 -Table 6 (Maximum Inside Diameter of Internal Parallel Thread)	-
9.1-Table 7 (Dimensions of Screwed Ends of Fittings-D )	-
9.1-Table 7 (Dimensions of Screwed Ends of Fittings-E )	-
9.1-Table 7 (Dimensions of Screwed Ends of Fittings-d )	-
9.1-Table 8 (Dimensions of Elbows, Tees and Crosses, Equal-A)	-
9.1-Table 9 (Dimensions of Elbows Reducing-A)	-
9.1-Table 9 (Dimensions of Elbows Reducing-B)	-
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-A)	-
9.1-Table 10 (Dimensions of Tees, Reducing (on the Branch)-B)	-
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-A)	-
9.1-Table 11 (Dimensions of Tees, Reducing (on the Run and Branch, or on the Run Only)-B)	-
9.1-Table 12 (Dimensions of Tees (Increasing on the Branch)-A)	-
9.1-Table 12 (Dimensions of Tees (Increasing on the Branch)-B)	-
9.1-Table 13 ( Dimensions of Crosses, Reducing-A)	-
9.1-Table 13 ( Dimensions of Crosses, Reducing-B)	-
9.1-Table 14 ( Elbows, Tees and Crosses, Side Outlet, Equal-A)	-
9.1-Table 14 ( Elbows, Tees and Crosses, Side Outlet, Equal-B)	-
9.1-Table 15 ( Dimensions of Elbows, Round, Male and Female, Equal-A)	-
9.1-Table 15 ( Dimensions of Elbows, Round, Male and Female, Equal-B)	-
9.1-Table 15 ( Dimensions of Elbows, Round, Male and Female, Equal-Minimum Bore of Male End)	-
9.1-Table 15 ( Dimensions of Elbows, Round, Male and Female, Equal-Maximum Bore of Male End)	-
9.1-Table 16 ( Dimensions of Elbows, Equal, 135°-A)	-
9.1-Table 17 (Dimensions of Y-Pieces, Female, Equal-A)	-
9.1-Table 18 (Dimensions of Socket, Reducing-A)	-
9.1-Table 19 (Dimensions of Caps-A)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge-S)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge-H)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge-D)	-
9.1-Table 20 (Dimensions of Plug-Minimum Length of Thread for Basic Gauge-K)	-
9.1-Table 21 (Dimensions of Elbows, Tees and Crosses, Male, Equal-A)	-
9.1-Table 22 (Dimensions of Y-Pieces and Angle Tees, Male, Equal-A )	-
9.1-Table 22 (Dimensions of Y-Pieces and Angle Tees, Male, Equal-B )	-
9.1-Table 23 ( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-A)	-
9.1-Table 23 ( Dimensions of Twin Elbows and Sweep Tees, Male, Equal-B)	-
9.1-Table 24 (Dimensions of Socket Unions-A )	-
9.1-Table 25 (Dimensions of Pipe Unions-A)	-
9.1-Table 26 (Dimensions of Union Bends-A )	-
9.1-Table 26 (Dimensions of Union Bends-B )	-
9.1-Table 27 (Dimensions of Hexagon Bushes-L)	-
9.1-Table 27 (Dimensions of Hexagon Bushes-T)	-
9.1-Table 27 (Dimensions of Hexagon Bushes-A)	-
9.1-Table 27 (Dimensions of Hexagon Bushes-B)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-L)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-T)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-A)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-C)	-
9.1-Table 28 (Dimensions of Nipples, Hexagon, Equal-B)	-
11.1(a) (Internal hydraulic Pressure Test)	-
11.1(a) (Internal Air Pressure Test)	-
11.2.1 ( Drift Expanding Test)	-
11.2.2 (Taper Screw Plug Test)	-
14 (WORKMANSHIP)	-
13 and as per IS 4736 (MASS OF ZINC COATING)	-
13 and as per IS 4736 (UNIFORMITY OF ZINC COATING)	-

-
-

260

IS 208 (1996)

Door Handles - Specification ( Sixth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 Table2A & 2B and Fig 1,2,3,4 (DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-
9 (MARKING)	-
9.1 (BIS Certification Marking)	-

-
Excluding Finish, Quenching Test, Micro alloying elements and alloy material

261

IS 7226 (1974)

Specification for cold - Rolled medium, high carbon and low alloy steel strip for general engineering purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.1, Table 3 (i)TOLERANCE ON WIDTH)	-
9.1, Table 4 (ii)TOLERANCE ON THICKNESS)	-
5 (HARDNESS TEST)	-
4.1 Table 1 (Carbon- IS 228)	-
4.1 Table 1 (Manganese- IS 228)	-
4.1 Table 1 (Silicon- IS 228)	-
4.1 Table 1 (Sulphur- IS 228)	-
4.1 Table 1 (Phosphorous- IS 228)	-

-
Excluding Cr, W, Micro Alloying Elements.

262

IS 11722 (1986)

Specification for thin walled flexible quick coupling pipes

4800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9 (Galvanizing ,IS 4736)	-
9 (Galvanizing ,IS 4736)	-
9 (Galvanizing ,IS 4736)	-
9 (Galvanizing ,IS 4736)	-
6 &7 ; Table 1 (Dimension & Tolerance)	-
8 (Length)	-
11, Table 3 (Angularity of Joint)	-
13.1 (Flattening Test,IS 2328)	-
13.2 (Tensile Test ,; IS 1608(P1))	-
4.1 (Pipe Manufacturing Process )	-
5,5.1 (Workmsnship &Finish)	-
9 (Galvanizing ,IS 4736)	-

-
Excluding Microalloying Elements

263

IS 3195 (1992)

Steel for the manufacture of volute and helical springs (For Railway Rolling Stock) - Specification (Third Revision)

1050 Chemical View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Hardness)	-
11 ( DIMENSIONS AND TOLERANCES)	-
10 (Freedom from defects)	-
Cl. 3, 6.1, 6.2 & Table 1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 3, 6.1, 6.2 & Table 1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Excluding Microalloying Elements, Decarburization, Inlusion rating

264

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

Rs.7500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Pipe ends, Angle of bevel & Root Face )	-
Cl 12 (Bituminous Coating & Galvanizing )	-
Cl 14 (Workmanship)	-
5.2 (phosphorus)	-
5.2 (sulphur)	-
Cl 14 (Workmanship)	-

-
Test facility is complete for Chemical Except HST

265

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

Rs.1500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (TYPES)	-
5.1- Table 2,3,4,5 & Fig-1 & 2 (Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-
5.1- Table 2,3,4,5 & Fig-1 & 2 (Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-
6.1 (Manufacture- General)	-
6.2- Table 2,3,4,5 (Kunckles)	-
6.3 (Screw Holes)	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2 (Screw Holes)	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-
6.3.3 Fig-1 (Position of Holes)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Carbon - IS 228)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Manganese - IS 228)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Sulphur - IS 228)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992) (Chemical composition - Phosphorous - IS 228)	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992) (Chemical composition - Silicon - IS 228 (optional))	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Carbon - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Silicon - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Manganese - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Sulphur - IS 228)	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995) (Chemical composition - Phosphorous - IS 228)	-

-
Excluding Finish Test, Facility for chemical testing is not available

266

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

Rs.2100.00. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (General)	-
5.2.1 Table 1 (Particulars-Barrel Tower Bolts)	-
5.2.2 Table 2 (Particulars-Skeleton Tower Bolts)	-
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-
6.1- Table 1 (Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts- Nos of Staples)	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-

-
Except Finish Test, Facility for chemical testing is not available

267

IS 204 : Part 1 (1991)

Tower bolts - Specification: Part 1 ferrous metals (Fifth Revision)

Rs.2100.00. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (General)	-
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt-A 3.Length of Barrel-B 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of mild steel sheet for barrel-F 8.Dia of bore of barrel or socket- G )	-
6.1- Table 1 (Dimension of Barrel tower bolts-Minimum No. of equally Spaced Screw holes in Barrel and Socket for wood screw no 6)	-
6.2- Table 2 (Dimension of Sami Barrel Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Bolt Plate or Socket-F 8.Dia of bore of Bolt Plate or socket G )	-
6.2- Table 2 (Dimension of Sami Barrel Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-
6.3- Table 3 (Dimension of Riveted or Spot Welded Tower Bolts- 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7. Length of Strap-E" 8.Thickness of Back Plate -F 9.Thickness of Socket or Upper Plate and Strap- F" 10.Dia of bore of Bolt Plate or socket- G 11. Length of Alternative Socket-H )	-
6.3- Table 3 (Dimension of Riveted or Spot Welded Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Staple -F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob-J)	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts- Nos of Staples)	-
6.4- Table 4 (Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 6)	-
8.1 (MARKING- .)	-
8.1.1, (MARKING- )	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017) (Chemical composition - Carbon - IS 228)	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017) (Chemical composition - Manganese - IS 228)	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017) (Chemical composition - Phosphorus - IS 228)	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017) (Chemical composition - Sulphur - IS 228)	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011) (Chemical composition - Carbon - IS 228)	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011) (Chemical composition - Manganese - IS 228)	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011) (Chemical composition - Sulphur - IS 228)	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011) (Chemical composition - Phosphorus - IS 228)	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011) (Chemical composition - Silicon - IS 228)	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011) (Chemical composition - Carbon Equivalen(CE) - IS 228)	-
4 -Table 5- iii (Ref. Cl 6.1 of IS 210 : 2009) (Chemical composition - Sulphur and/or Phosphorous)	-

-
Excluding Finish Test,

268

IS 4148 (1989)

Surgical rubber gloves - Specification (First Revision)

Rs. 3925/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5 (pH of Aqueous Extract )	-

-
Test facility is complete for Chemical Except Mechanical test facility is not available

269

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-
Cl 9 (Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-
Cl 8 (Workmanship)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
6.1 ( Copper %)	-
6.1 ( Aluminium %)	-
6.1 ( Nb)	-
6.1 (V)	-
6.1 ( Ti)	-
6.1 (Boron)	-
6.1 (Microalloying)	-

-
-

270

IS 1812 (1982)

Specification for carbon steel wire for the manufacture of wood screws (Second Revision)

825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 ( Tensile Test IS1608(P-1))	-
6.2 ( Bend Test )	-
6.3 ( Wrapping Test )	-
7 (. SIZE TOLERANCE)	-
8 ( FREEDOM FROM DEFECTS)	-
Cl. 5.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-

-
Except aluminium killed

Bureau of Indian Standards

The National Standards Body of India

BIS, Northern Regional Laboratory (NRL)

B-69, Industrial Focal Point, Phase VII, Mohali, Mohali, S.A.S Nagar, Punjab, 160059

- nrolsample@bis.gov.in

Scope List