BIS - LIMS (Laboratory Information Management System)

Alpha Test House Private Limited, Delhi

487/25, Near Prachin Shiv Mandir Peeragarhi, DELHI, New Delhi, Delhi, 110087

9711227171 electrical@alphatesthouse.com

Scope List

Reset

98 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1258 (2024)

Bayonet lampholders (Fifth Revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General requirements)	-	100	-
6(Standard ratings)	-	100	-
7(Classification)	-	100	-
8(Marking)	-	300	-
9(Dimensions)	-	700	-
10(Protection against electric shock)	-	700	-
11(Terminals)	-	1000	-
12(Provision for earthing)	-	1000	-
13(Construction)	-	500	-
14(Switched lampholders)	-	500	-
15(Moisture resistance, insulation resistance and electrical strength)	-	2000	-
16(Mechanical strength)	-	500	-
17(Screws, current-carrying parts and connections)	-	500	-
18(Creepage distances and clearances)	-	500	-
19(General resistance to heat)	-	1000	-
20(Resistance to heat, fire and tracking)	-	1000	-
21(Resistance to excessive residual stresses (season cracking) and to rusting)	-	1000	-
Annex A(Season cracking/corrosion test)	-	1000	-
12.4(Thermal tests)	-	500	-
9.1(Lampholder dimensions)	-	500	-
11.2(Terminals)	-	500	-
12.3(Provision for earthing)	-	700	-
13.1(Construction)	-	500	-
13.8(Construction)	-	500	-
14.4(Switched lampholders)	-	500	-
15.1(Moisture resistance, insulation resistance and electrical strength)	-	2000	-
16.7(Mechanical strength)	-	500	-
16.8(Mechanical strength)	-	200	-
21.2(Resistance to excessive residual stresses (season cracking) and to rusting)	-	600	-

-
Included .w.e.f.11.02.2025

IS 16221 : Part 2 (2015)

Safety of power converters for use in photovoltaic power systems: Part 2 particular requirements for inverters

204000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	1000	-
5(Marking and documentation)	-	5000	-
6(Environmental requirements and conditions)	-	1000	-
7(Protection against electric shock and energy hazards)	-	5000	-
8(Protection against Mechanical Hazards)	-	5000	-
9(Protection against Fire Hazards)	-	5000	-
10(Protection against Sonic Pressure Hazards)	-	5000	-
11(Protection against Liquid Hazards)	-	5000	-
12(Protection against Chemical Hazards)	-	5000	-
13(Physical Requirements)	-	5000	-
9.1.4.3(Hot flaming oil test)	-	5000	-
Clause No. 4.3(Thermal testing)	-	10000	-
Clause No. 4.4(Testing in single fault condition)	-	10000	-
4.5(Humidity preconditioning)	-	10000	-
4.6(Backfeed voltage protection)	-	5000	-
4.7(Electrical rating tests)	-	3000	-
4.8(Additional tests for grid interactive inverters)	-	5000	-
4(General Test Requirements)	-	1000	-
5(Marking and documentation)	-	5000	-
6(Environmental requirements and conditions)	-	1000	-
7(Protection against electric shock and energy hazards)	-	5000	-
8(Protection against Mechanical Hazards)	-	5000	-
9(Protection against Fire Hazards)	-	5000	-
10(Protection against Sonic Pressure Hazards)	-	5000	-
11(Protection against Liquid Hazards)	-	5000	-
12(Protection against Chemical Hazards)	-	5000	-
13(Physical Requirements)	-	5000	-
4.4.4.15.1(Fault-tolerance of residual current monitoring)	-	5000	-
4.4.4.15.2(Fault-tolerance of automatic disconnecting means)	-	5000	-
4.4.4.16(Stand-alone inverters – Load transfer test)	-	5000	-
4.4.4.17(Cooling system failure – Blanketing test)	-	5000	-
4.7.3(Measurement requirements for AC output ports for stand-alone inverters)	-	5000	-
4.7.4(Stand-alone Inverter AC output voltage and frequency)	-	5000	-
4.7.4.2(Steady state output voltage at nominal DC input)	-	5000	-
4.7.4.3(Steady state output voltage across the DC input range)	-	5000	-
4.7.4.4(Load step response of the output voltage at nominal DC input)	-	5000	-
4.7.4.5(Steady state output frequency)	-	5000	-
4.7.5(Stand-alone inverter output voltage waveform)	-	5000	-
4.7.5.2(Sinusoidal output voltage waveform requirements)	-	5000	-
4.7.5.3(Non-sinusoidal output waveform requirements)	-	5000	-
4.7.5.5(Output voltage waveform requirements for inverters for dedicated loads)	-	5000	-
4.8.2.1(Array insulation resistance detection for inverters for ungrounded arrays)	-	5000	-
4.8.2.2(Array insulation resistance detection for inverters for functionally grounded arrays)	-	5000	-
4.8.3.2(30 mA touch current type test for isolated inverters)	-	5000	-
4,8.3.3(Fire hazard residual current type test for isolated inverters)	-	5000	-
4.8.3.5(Protection by residual current monitoring)	-	5000	-
7.3.10(Additional requirements for stand-alone inverters)	-	5000	-
9.3.4(Inverter backfeed current onto the array)	-	5000	-
13.9(Fault indication)	-	5000	-

-
Included w.e.f. 23.02.2024 Exclusion: Cl.14 (Components), CL.6.4 (UV exposure), Cl.13.6.4 (UV Resistance), Cl.Annex J (Ultraviolet light conditioning test), Cl.9.1.4.3 (Hot flaming oil test)

IS 16221 : Part 1 (2016)

Safety of Power Converters for use in Photovoltaic Power Systems Part 1 General Requirements

524000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13.6.2.1(Stress relief test)	-	5000	-
9(Protection Against Fire Hazards)	-	10000	-
8(Protection Against mechanical Hazards)	-	10000	-
7(Protection against electric shock and energy hazards)	-	5000	-
5(Marking and documentation)	-	5000	-
4(General testing requirements)	-	1000	-
6.4(UV exposure)	-	1000	-
4.2(Thermal testing)	-	10000	-
4.4(Testing in single fault condition)	-	10000	-
4.5(Humidity preconditioning)	-	10000	-
4.6(Backfeed voltage protection)	-	5000	-
4.7(Electrical rating tests)	-	3000	-
4.8(Additional tests for grid interactive inverters)	-	5000	-
Annex A(Measurement of clearances and creepage distances)	-	3000	-
Annex B(Programmable equipment)	-	1000	-
Annex C(Symbols to be used in equipment markings)	-	1000	-
Annex D(Test probes for determining access)	-	1000	-
Annex E(RCDs)	-	1000	-
Annex F(Altitude correction for clearances)	-	1000	-
Annex G(Clearance and creepage distance determination for frequencies greater than 30 kHz)	-	1000	-
Annex H("Measuring instrument for touch current measurements ")	-	1000	-
Annex I("Examples of protection, insulation, and overvoltage category requirements for PCE ")	-	1000	-
4.3, 4.3.2, 4.3.2.2, 4.3.2.3(Thermal Tests (Maximum temperatures, Touch temperature, temperature limits for mount surfaces))	-	10000	-
4.4.3.1(Protection against shock hazard)	-	5000	-
4.4.3.2(Protection against spread of fire)	-	5000	-
4.4.3.4(Protection Against parts expulsion hazards)	-	5000	-
4.4.4.5(Output short circuit)	-	5000	-
4.4.4.6(Backfeed current test for equipment with more than one source of supply)	-	5000	-
4.4.4.7(Output overload)	-	5000	-
4.4.4.8(Cooling system failure)	-	5000	-
4.4.4.9(Heating devices)	-	5000	-
4.4.4.10(Safety interlock systems)	-	5000	-
4.4.4.11(Reverse d.c. connections)	-	5000	-
4.4.4.12(Voltage selector mismatch)	-	5000	-
4.4.4.13(Mis-wiring with incorrect phase sequence or polarity)	-	5000	-
4.4.4.14(Printed wiring board short-circuit test)	-	5000	-
4.6.1(Backfeed tests under normal conditions)	-	5000	-
4.6.2(Backfeed tests under single-fault conditions)	-	5000	-
5.1.2(Durability of markings)	-	5000	-
5.2.1(Visibility and legibility requirements for warning markings)	-	1000	-
7.3.2.3(Short-term limits of accessible voltages under fault conditions)	-	5000	-
7.3.2.6(Working voltage and DVC)	-	5000	-
7.3.4,7.3.4.2(protection against direct contact)	-	5000	-
7.3.4.3(Protection by means of insulation of live parts)	-	5000	-
7.3.5,7.3.5.2(Protection in case of direct contact)	-	5000	-
7.3.5.3.1(Limitation of current through protective impedance)	-	5000	-
7.3.5.3.2(Limitation of discharging energy through protective impedance)	-	5000	-
7.3.5.4(Protection by means of limited voltages)	-	5000	-
7.3.6.1,7.3.6.2(Protection against indirect contact(Creapage & clearance))	-	5000	-
7.3.6.3(Protective class I - Protective bonding and earthing)	-	5000	-
7.3.6.3.3(Rating of protective bonding)	-	5000	-
7.3.7.4(Clearance distances)	-	5000	-
7.3.7.5(Creepage distances)	-	5000	-
7.3.8(Residual current detection (RCD) or Monitoring (RCM) device compatibilty (DC components on AC side))	-	5000	-
7.3.9(Protection against shock hazard due to stored energy)	-	5000	-
7.4(Protection against energy hazards)	-	5000	-
7.5.1(Impulse voltage test (type test))	-	5000	-
7.5.2(Voltage test (dielectric strength test))	-	5000	-
7.5.4(Touch current measurement)	-	5000	-
8.2(Moving parts)	-	5000	-
8.3(Stability)	-	5000	-
8.4(Provisions for lifting and carrying)	-	5000	-
8.5(Wall mounting)	-	5000	-
8.6(Expelled parts)	-	5000	-
9.1.1(Reducing the risk of ignition and spread of flame)	-	5000	-
9.1.2(Conditions for a fire enclosure)	-	5000	-
9.1.3(Material requirements for protection against fire hazard)	-	5000	-
9.1.4(Openings in fire enclosures)	-	5000	-
9.1.4.6(Additional requirements for openings in transportable equipment)	-	5000	-
9.2.2(Limited power source tests)	-	5000	-
9.3(Short-circuit and overcurrent protection)	-	5000	-
11.1(Liquid containment, pressure and leakage)	-	5000	-
11.2(Fluid pressure and leakage)	-	5000	-
13.1(Handles and manual controls)	-	5000	-
13.2(Securing of parts)	-	5000	-
13.3(Provisions for external connections)	-	5000	-
13.4(Internal wiring and connections)	-	5000	-
13.5(Openings in enclosures)	-	5000	-
13.3.2.5(Cord anchorages and strain relief)	-	5000	-
13.3.5(Wire bending space for wires 10mm2 and greater)	-	5000	-
13.5(Openings in enclosures)	-	5000	-
13.7(Mechanical resistance to deflection, impact, or drop)	-	5000	-
13.8(Thickness requirements for metal enclosures)	-	5000	-
14.2(Motor over-temperature protection)	-	5000	-
14.3(Over-temperature protection devices)	-	5000	-
14.6(Printed circuit boards)	-	5000	-
14.7(Circuits or components used as transient overvoltage limiting devices)	-	5000	-
9.1.4.3(Hot flaming oil test)	-	5000	-
7.3.7.8.4.2(Use of coating materials (on PWBs))	-	5000	-
7.5.3(Partial discharge test (type test or sample test))	-	20000	-
10.2(Sonic pressure and sound level)	-	5000	-
10(Protection against Sonic Pressure hazards)	-	5000	-
6.3(Ingress protection)	-	10000	-
15(Software and firmware performing safety functions)	-	5000	-
12(Chemical hazards)	-	5000	-
11(Protection against liquid hazards)	-	5000	-
6(Environmental Requirements and conditions)	-	10000	-
4.4.4.1(Component fault tests)	-	5000	-
4.4.4.2(Equipment’s or parts for short-term or intermittent operation)	-	5000	-
4.4.4.3(Motors(Lock rotor))	-	5000	-
4.4.4.4(Transformer short circuit tests)	-	5000	-
13.1.1(Adjustable controls)	-	5000	-
7.3.7.5(Creepage distances)	-	5000	-
7.3.8(Residual current detection (RCD) or Monitoring (RCM) device compatibilty (DC components on AC side))	-	5000	-
7.3.9(Protection against shock hazard due to stored energy)	-	5000	-
7.4(Protection against energy hazards)	-	5000	-
7.5.1(Impulse voltage test (type test))	-	5000	-
7.5.2(Voltage test (dielectric strength test))	-	5000	-
7.5.2.3(Humidity preconditioning)	-	10000	-
7.5.3(Partial discharge test (type test or sample test))	-	20000	-
7.5.4(Touch current measurement)	-	5000	-

-
Included w.e.f. 23.02.2024 Exclusion: Cl.14 (Components), Cl.6.4 (UV exposure), Cl.13.6.4 (UV Resistance), Annex J (Ultraviolet light conditioning test), Cl.9.1.4.3 (Hot flaming oil test), Cl.14.2 (Motor over-temperature protection), Cl.14.3 (Over-temperature protection devices), Cl.14.6 (Printed circuit boards), Cl.14.7 (Circuits or components used as transient overvoltage limiting devices)

IS 16169 (2019)

Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures (First Revision)

157000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Test for single or multi-phase inverter)	-	145000	-
Annex A(Islanding as it applies to PV systems)	-	1000	-
Annex B(Test for independent islanding device)	-	1000	-
6 to 6.2(Test for single or multi-phase inverter to Pass/fail criteria)	-	5000	-
7(Documentation)	-	2000	-
4(Testing circuit)	-	1000	-
5(Testing equipment)	-	1000	-
Annex C(Gate blocking signal)	-	1000	-
6 to 6.2(Test for single or multi-phase inverter to Pass/fail criteria)	-	-	-
7(Documentation)	-	-	-
4(Testing circuit)	-	-	-
5(Testing equipment)	-	-	-
Annex C(Gate blocking signal)	-	-	-

-
Included w.e.f. 23.02.2024

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

Fixed General Purpose Luminaires

56000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	0	-
5(Classification of Luminaires')	-	2000	-
6.0(Marking)	-	2000	-
7.0(Construction)	-	5000	-
8.0(Creepage Distance and Clearances)	-	3000	-
9.0(Provision for earthing)	-	3000	-
10.0(Terminals)	-	5000	-
11.0(External & Internal Wiring)	-	5000	-
12.0(Protection against electric shock)	-	3000	-
13.0(Endurance Tests and Thermal Tests)	-	12000	-
14.0(Resistance to Dust & Moisture)	-	5000	-
15.0(Insulation Resistance and Electric Strength)	-	5000	-
16.0(Resistance to Heat , fire and tracking)	-	6000	-
17.0(Photometric Test)	-	0	-

-
Included w.e.f. 31.08.2023

IS 16242 : Part 1 (2014)

Uninterruptible power systems (UPS): Part 1 general and safety requirements for UPS

UPS and Inverters

76000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.6(Power interface)	-	5000	-
4.7(Marking & instructions)	-	2000	-
5.1(Protection against shock and energy hazards)	-	3000	-
5.2(Requirement of auxiliary circuits)	-	2000	-
5.3(Protective earthing and bonding)	-	3000	-
5.4(AC and DC power isolation)	-	2000	-
5.5(Over current and earth fault condition)	-	2000	-
5.6(Safety interlocks)	-	1000	-
5.7(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	2000	-
6.1(Wiring, connections and supply)	-	2000	-
6.2(Connection to power)	-	1000	-
6.3(Wiring terminals for external power conductors)	-	1000	-
7.1(Enclosure)	-	2000	-
7.2(STABILITY)	-	3000	-
7.3(MECHANICAL STRENGTH)	-	5000	-
7.4(Construction details)	-	3000	-
7.5(Resistance to fire)	-	5000	-
7.6(Battery location)	-	1000	-
4.5(Components)	-	1000	-
7.7(Temperature rise)	-	6000	-
8.1(General procision for earth leakage)	-	5000	-
8.2(Electric Strength)	-	3000	-
8.3(Abnormal operating and fault conditions)	-	5000	-
9.0(Connection to telecommunication networks)	-	1000	-
4.5/RD 1.5(Components)	-	1000	-
2.10.5.11(SMPS/Main transformer)	-	1000	-
2.10.6(PCB Material)	-	1000	-
3.2.5(Non-rewirable plug with PVC sheathed cable)	-	1000	-
3.2.4(Appliances inlets/connectors)	-	1000	-
2.10.5.4(Semiconductor devices)	-	1000	-
2.10.5.13(Winding wires)	-	1000	-
4.3.8(Batteries)	-	1000	-
2.10.5.6(Thin sheet material)	-	1000	-
5.6.1/ RD 2.8.7(Switches & Relays)	-	1000	-
6.1.1/ RD 3.1.4(Insulating Conductors)	-	1000	-
Annex I.5(Solid-state backfeed protection)	-	1000	-
I.5(transient overvoltages)	-	0	-
I.5(voltage variations)	-	0	-
I.5(electromagnetic susceptibility)	-	0	-
I.5(electrostatic discharge)	-	0	-
Annex I.5(Solid-state backfeed protection)	-	0	-

-
Included w.e.f. 02.12.2023. Exclusion: Annex I.5 (transient overvoltages, voltage variations, electromagnetic susceptibility, electrostatic discharge, Solid-state backfeed protection), Cl. 2.10.6 (PCB Material), Cl. 3.2.5 (Non-rewirable plug with PVC sheathed cable), Cl. 2.10.5.4 (Semiconductor devices), Cl. 5.6.1/ RD 2.8.7 (Switches & Relays), Annex M (Ventilation of battery compartments), Cl. 2.10.8 of RD (Tests on coated printed boards and coated components), Cl. 2.10.9 of RD (Thermal cycling), Cl. 2.10.10 of RD (Test for Pollution Degree 1 environment and for insulating compound), Cl. 2.10.11 of RD (Tests for semiconductor devices and for cemented joints)

IS 10322 : Part 5 : Sec 9 (2017)

Luminaires: Part 5 particular requirements: Sec 9 rope lights

Rope Light

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
21.4(General Test Requireements)	-	1000	-
21.5(Classification of Luminaires')	-	2000	-
21.6(Marking)	-	2000	-
21.7(Construction)	-	5000	-
21.8(Creepage Distance and Clearances)	-	3000	-
21.9(Provision for earthing)	-	0	-
21.10(Terminals)	-	5000	-
21.11(External & Internal Wiring)	-	2000	-
21.12(Protection against electric shock)	-	3000	-
21.13(Endurance Tests and Thermal Tests)	-	12000	-
21.14(Resistance to Dust & Moisture)	-	2000	-
21.15(Insulation Resistance and Electric Strength)	-	2000	-
21.16(Resistance to Heat , fire and tracking)	-	6000	-
21.7.1(General)	-	0	-
21.7.3(Terminals and supply connections)	-	0	-
21.7.4(Control units)	-	0	-
21.7.5(Mechanical strength)	-	0	-

-
Included w.e.f. 17.11.2023

IS 302 : Part 2 : Sec 23 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 23 appliances for skin or hair care (First Revision)

24500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation ,Toxicity and similar hazards)	-	1000	Testing charges
31(Resistance to Rusting)	-	1000	Testing charges
30(Resistance to Heat & Fire)	-	1800	Testing charges
29(Clearances, Creepage Distances & Solid Insulation)	-	1000	Testing charges
28(Screws & Connection)	-	1000	Testing charges
27(Provision For Earthing)	-	1000	Testing charges
26(Terminals For External Conductors)	-	1000	Testing charges
25(Supply Connection & External Flexible Cables and Cords)	-	1000	Testing charges
24(Component)	-	1000	Testing charges
23(Internal wiring)	-	1000	Testing charges
22(Construction)	-	1000	Testing charges
21(Mechanical strength)	-	1000	Testing charges
20(Stability & Mechanical Hazards)	-	1000	Testing charges
19(Abnormal Operation)	-	1000	Testing charges
18(Endurance)	-	0	Testing charges
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1000	Testing charges
16(Leakage Current and Electric Strength)	-	1000	Testing charges
15(Moisture Resistance)	-	1000	Testing charges
14(Transient Over Voltage)	-	1000	Testing charges
13(Leakage Current and Electric Strength at Operating Temperature)	-	500	Testing charges
11(Temperature Rise/Heating)	-	1800	Testing charges
10(Power Input & Current)	-	1000	Testing charges
9(Starting Of Motor Operated Appliances)	-	0	Testing charges
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1000	Testing charges
7(Marking/ Marking & Instructions)	-	1000	Testing charges
6(Classification)	-	100	Testing charges
22.32(CONSTRUCTION)	-	0	Testing charges

-
Included w.e.f. 17.11.2023. Exclusion: Cl 19.11.4.1 to 19.11.4.7 (EMI/EMC Tests), Cl 24.1. 1,24.1.2 & 24.1.5 (Components)

IS 302 : Part 2 : Sec 13 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 13 frying pans, deep fat fryers and similar appliances

24000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation ,Toxicity and similar hazards)	-	1000	Testing charges
31(Resistance to Rusting)	-	1000	Testing charges
30(Resistance to Heat, Fire and Tracking)	-	1800	Testing charges
29(Clearances, Creepage Distances & Solid Insulation)	-	1000	Testing charges
28(Screws & Connections)	-	1000	Testing charges
27(Provision For Earthing)	-	1000	Testing charges
26(Terminals For External Conductors)	-	1000	Testing charges
25(Supply Connection & External Flexible Cables and Cords)	-	1000	Testing charges
24(Components)	-	1000	Testing charges
23(Internal wiring)	-	1000	Testing charges
22(Construction)	-	1000	Testing charges
21(Mechanical strength)	-	1000	Testing charges
20(Stability & Mechanical Hazards)	-	1000	Testing charges
19(Abnormal Operation)	-	1000	Testing charges
18(Endurance)	-	0	Testing charges
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1000	Testing charges
16(Leakage Current and Electric Strength)	-	0	Testing charges
15(Moisture Resistance)	-	1800	Testing charges
14(Transient Over Voltage)	-	1000	Testing charges
13(Leakage Current and Electric Strength at Operating Temperature)	-	500	Testing charges
11(Temperature Rise/Heating)	-	1800	Testing charges
10(Power Input)	-	1000	Testing charges
9(Starting Of Motor Operated Appliances)	-	0	Testing charges
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1000	Testing charges
7(Marking/ Marking & Instructions)	-	1000	Testing charges
6(Classification)	-	100	Testing charges
5(Rating)	-	0	Testing charges

-
Cl. 19.11.4.1 to 19.11.4.7 24 (Components)

IS 302 : Part 2 : Sec 9 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 9 toasters, grills, roasters and similar appliances (First Revision)

9800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.32(Verification)	-	0	Testing charges
Cl.31(Verification)	-	0	Testing charges
Cl.30(Verification)	-	0	Testing charges
CL.29(Verification)	-	0	Testing charges
Cl.28(Verification)	-	0	Testing charges
Cl.27(Verification)	-	0	Testing charges
Cl.26(Verification)	-	0	Testing charges
Cl.25(Verification)	-	0	Testing charges
Cl.24(Verification)	-	0	Testing charges
Cl.23(Verification)	-	0	Testing charges
Cl.22(Verification)	-	0	Testing charges
Cl.21(Verification)	-	0	Testing charges
Cl.20(Verification)	-	0	Testing charges
Cl.19(Verification)	-	0	Testing charges
Cl. 16(Verification)	-	0	Testing charges
Cl.15.1(Moisture Resistance)	-	0	Testing charges
Cl.14(Verification)	-	0	Testing charges
Cl.13(Verification)	-	0	Testing charges
Cl.11(Verification)	-	0	Testing charges
Cl.10(Verification)	-	0	Testing charges
Cl.8(Verification)	-	0	Testing charges
Cl. 7(Verification)	-	0	Testing charges
Cl. 6(Classification- IS 302-1)	-	0	Testing charges
Cl. 32 IS 302-2-9(Radiation, Toxicity and similar hazards)	-	0	Testing charges
Cl. 31 IS 302-2-9(Resistance To Rusting )	-	0	Testing charges
Cl. 30 IS 302-2-9(Resistance To Heat, Fire And Tracking)	-	0	Testing charges
Cl. 29 IS 302-2-9(Creepage Distances, Clearances And Distances Through Insulation)	-	0	Testing charges
Cl. 28 IS 302-2-9(Screws and Connections)	-	0	Testing charges
Cl. 27 IS 302-2-9(Provision For Earthing )	-	0	Testing charges
Cl. 26 IS 302-2-9(Terminal For External Conductors )	-	0	Testing charges
Cl. 25 IS 302-2-9(Supply Connections and External Flexible Cables and Cords )	-	0	Testing charges
Cl. 24 IS 302-2-9(Components)	-	0	Testing charges
Cl. 23 IS 302-2-9(Internal Wiring)	-	0	Testing charges
Cl. 22 IS 302-2-9(Construction )	-	0	Testing charges
Cl. 21 IS 302-2-9(Mechanical Strength)	-	0	Testing charges
Cl. 20 IS 302-2-9(Stability and mechanical Hazards)	-	0	Testing charges
Cl. 19 IS 302-2-9(Abnormal Operation )	-	0	Testing charges
Cl. 18 IS 302-2-9(Endurance)	-	0	Testing charges
Cl. 17 IS 302-2-9(Overload protection of transformers and associated circuits.)	-	0	Testing charges
Cl. 16 IS 302-2-9(Leakage Current and Electric strength )	-	0	Testing charges
Cl. 15 IS 302-2-9(Moisture Resistance)	-	0	Testing charges
Cl. 14 IS 302-2-9(Transient overvoltage)	-	0	Testing charges
Cl. 13.3 IS 302-2-9(Leakage Current & Electric Strength at Operating Temperature)	-	0	Testing charges
Cl. 11 IS 302-2-9(Heating)	-	0	Testing charges
Cl. 10 IS 302-2-9(Power Input and Current )	-	0	Testing charges
Cl. 9 IS 302-2-9(Starting of motor operated appliances)	-	0	Testing charges
Cl. 8 IS 302-2-9(Protection against access to live parts)	-	0	Testing charges
Cl. 7 IS 302-2-9(Marking and Instruction)	-	0	Testing charges
Cl. 6 IS 302-2-9(Classification- IS 302-1)	-	0	Testing charges
32(Radiation, toxicity and similar hazards)	-	0	Testing charges
31(Resistance to rusting)	-	0	Testing charges
31(Resistance to rusting)	-	0	Testing charges
30.2.4(Resistance to heat and fire)	-	0	Testing charges
30.2(Resistance to heat and fire)	-	0	Testing charges
30.1(Resistance to heat and fire)	-	0	Testing charges
29.3(Clearances, creepage distances and solid insulation)	-	0	Testing charges
29.2(Clearances, creepage distances and solid insulation)	-	0	Testing charges
29.2(Clearances, creepage distances and solid insulation)	-	0	Testing charges
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	0	Testing charges
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	0	Testing charges
28.2 to 28.4(Screws and connections)	-	0	Testing charges
28.1, Table No.-14(Screws and connections)	-	0	Testing charges
27.6(Provision for earthing)	-	0	Testing charges
27.5(Provision for earthing)	-	0	Testing charges
27.1 to 27.4(Provision for earthing)	-	0	Testing charges
26.10 & 26.11(Terminals for external conductors)	-	0	Testing charges
26.9(Terminals for external conductors)	-	0	Testing charges
26.1 to 26.8(Terminals for external conductors)	-	0	Testing charges
25.16 to 25.25(Supply connection and external flexible cords)	-	0	Testing charges
25.15(Supply connection and external flexible cords)	-	0	Testing charges
25.14(Supply connection and external flexible cords)	-	0	Testing charges
25.14(Supply connection and external flexible cords)	-	0	Testing charges
25.9 to 25.13(Supply connection and external flexible cords)	-	0	Testing charges
25.8, Table No.-11(Supply connection and external flexible cords)	-	0	Testing charges
25.5 to 25.7(Supply connection and external flexible cords)	-	0	Testing charges
25.4(Supply connection and external flexible cords)	-	0	Testing charges
25.3(Supply connection and external flexible cords)	-	0	Testing charges
25.2(Supply connection and external flexible cords)	-	0	Testing charges
25.1(Supply connection and external flexible cords)	-	0	Testing charges
24.101(Components)	-	0	Testing charges
24.2 to 24.6(Components)	-	0	Testing charges
24.1(Components)	-	0	Testing charges
23.6 to 23.10(Internal wiring)	-	0	Testing charges
23.5(Internal wiring)	-	0	Testing charges
23.4(Internal wiring)	-	0	Testing charges
23.3(Internal wiring)	-	0	Testing charges
23.1 & 23.2(Internal wiring)	-	0	Testing charges
22.111(Constructions)	-	0	Testing charges
22.111(Constructions)	-	0	Testing charges
22.11o(Constructions)	-	0	Testing charges
22.109(Constructions)	-	0	Testing charges
22.108(Constructions)	-	0	Testing charges
22.101 to 22.107(Constructions)	-	0	Testing charges
31(Resistance to rusting)	-	0	Testing charges
22.12(Constructions)	-	0	Testing charges
22.11(Constructions)	-	0	Testing charges
22.11(Constructions)	-	0	Testing charges
22.7 to 22.10(Constructions)	-	0	Testing charges
22.13 to 22.48(Constructions)	-	0	Testing charges
22.6(Constructions)	-	0	Testing charges
22.5(Constructions)	-	0	Testing charges
22.4(Constructions)	-	0	Testing charges
22.3(Constructions)	-	0	Testing charges
22.2(Constructions)	-	0	Testing charges
22.1(Constructions)	-	0	Testing charges
21.101(MECHANICAL STRENGTH)	-	0	Testing charges
21.101(MECHANICAL STRENGTH)	-	0	Testing charges
21.2(MECHANICAL STRENGTH)	-	0	Testing charges
20.2(Stability and mechanical hazards)	-	0	Testing charges
20.1(Stability and mechanical hazards)	-	0	Testing charges
19.104(ABNORMAL OPERATION)	-	0	Testing charges
19.103(ABNORMAL OPERATION)	-	0	Testing charges
19.102(ABNORMAL OPERATION)	-	0	Testing charges
19.101(ABNORMAL OPERATION)	-	0	Testing charges
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	0	Testing charges
17(Overload protection of transformers and associated circuits)	-	0	Testing charges
16.3(Insulation resistance test)	-	0	Testing charges
16.3(Electric strength test)	-	0	Testing charges
16.1 & 16.2(Leakage current test)	-	0	Testing charges
15.3(Moisture resistance)	-	0	Testing charges
15.2(Moisture resistance)	-	0	Testing charges
15.1(Moisture resistance)	-	0	Testing charges
14, Table No.- 6 & Table No.-16(Transient over voltages)	-	0	Testing charges
13.3 and Table No.- 4(Electric strength test)	-	0	Testing charges
13.1, 13.2(Leakage current test)	-	0	Testing charges
11.101(Heating)	-	0	Testing charges
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	0	Testing charges
8.1.5(Protection against access to live parts)	-	0	Testing charges
8.1.4(Protection against access to live parts)	-	0	Testing charges
8.1.3(Protection against access to live parts)	-	0	Testing charges
8.1.2(Protection against access to live parts)	-	0	testing charges
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	0	testing charges
7.14(Legibility & Durability of Markings test)	-	0	testing charges
32(Radiation, toxicity and similar hazards)	-	0	testing charges
30.2.4(Resistance to heat and fire)	-	0	Testing charges
30.1(Resistance to heat and fire)	-	0	Testing charges
29.3(Clearances, creepage distances and solid insulation)	-	0	Testing charges
29.2(Clearances, creepage distances and solid insulation)	-	0	Testing charges
29.1, Table No.- 16, Table No.- 17 & Table No.18(Clearances, creepage distances and solid insulation)	-	0	Testing charges
28.2 to 28.4(Screws and connections)	-	0	Testing charges
28.1, Table No.-14(Screws and connections)	-	0	Testing charges
27.6(Provision for earthing)	-	0	Testing charges
27.5(Provision for earthing)	-	0	Testing charges
27.1 to 27.4(Provision for earthing)	-	0	Testing charges
26.9(Terminals for external conductors)	-	0	Testing charges
26.1 to 26.8(Terminals for external conductors)	-	0	Testing charges
25.16 to 25.25(Supply connection and external flexible cords)	-	0	Testing charges
25.15(Supply connection and external flexible cords)	-	0	Testing charges
25.14(Supply connection and external flexible cords)	-	0	Testing charges
25.9 to 25.13(Supply connection and external flexible cords)	-	0	Testing charges
25.8, Table No.-11(Supply connection and external flexible cords)	-	0	Testing charges
25.5 to 25.7(Supply connection and external flexible cords)	-	0	Testing charges
25.4(Supply connection and external flexible cords)	-	0	Testing charges
25.3(Supply connection and external flexible cords)	-	0	Testing charges
25.2(Supply connection and external flexible cords)	-	0	Testing charges
25.1(Supply connection and external flexible cords)	-	0	Testing charges
24.101(Components)	-	0	Testing charges
24.2 to 24.6(Components)	-	0	Testing charges
24.1(Components)	-	0	Testing charges
23.6 to 23.10(Internal wiring)	-	0	Testing charges
23.5(Internal wiring)	-	0	Testing charges
23.4(Internal wiring)	-	0	Testing charges
23.3(Internal wiring)	-	0	Testing charges
23.1 & 23.2(Internal wiring)	-	0	Testing charges
22.111(Constructions)	-	0	Testing charges
22.11o(Constructions)	-	0	Testing charges
22.109(Constructions)	-	0	Testing charges
22.108(Constructions)	-	0	Testing charges
22.101 to 22.107(Constructions)	-	0	Testing charges
22.13 to 22.48(Constructions)	-	0	Testing charges
22.11(Constructions)	-	0	Testing charges
22.7 to 22.10(Constructions)	-	0	Testing charges
22.6(Constructions)	-	0	Testing charges
22.5(Constructions)	-	0	Testing charges
22.4(Constructions)	-	0	Testing charges
22.3(Constructions)	-	0	Testing charges
22.2(Constructions)	-	0	Testing charges
22.1(Constructions)	-	0	Testing charges
21.101(MECHANICAL STRENGTH)	-	0	Testing charges
21.2(MECHANICAL STRENGTH)	-	0	Testing charges
21.1(MECHANICAL STRENGTH)	-	0	Testing charges
20.2(Stability and mechanical hazards)	-	0	Testing charges
19.104(ABNORMAL OPERATION)	-	0	Testing charges
19.103(ABNORMAL OPERATION)	-	0	Testing charges
19.102(ABNORMAL OPERATION)	-	0	Testing charges
19.101(ABNORMAL OPERATION)	-	0	Testing charges
19.1 to 19.13, Table No. - 9(ABNORMAL OPERATION)	-	0	Testing charges
17(Overload protection of transformers and associated circuits)	-	0	Testing charges
16.1 & 16.2(Leakage current test)	-	0	Testing charges
15.3(Moisture resistance)	-	0	Testing charges
15.2(Moisture resistance)	-	0	Testing charges
15.1(Moisture resistance)	-	0	Testing charges
13.1, 13.2(Leakage current test)	-	0	Testing charges
11.101(Heating)	-	0	Testing charges
10.1 & 10.2 -Table No. 1, Table No. 2(Power Input and Current)	-	0	Testing charges
8.1.5(Protection against access to live parts)	-	0	Testing charges
8.1.4(Protection against access to live parts)	-	0	Testing charges
8.1.3(Protection against access to live parts)	-	0	Testing charges
8.1.2(Protection against access to live parts)	-	0	Testing charges
8.1, 8.1.1 & 8.2(Protection against access to live parts)	-	0	Testing charges
7.14(Legibility & Durability of Markings test)	-	0	Testing charges
7.1 to 7.13, 7.15, 7.16(Marking)	-	0	Testing charges
32(Radiation ,Toxicity and similar hazards)	-	200	Testing charges
31(Resistance to Rusting)	-	200	Testing charges
30(Resistance to Heat & Fire)	-	600	Testing charges
29(Clearances, Creepage Distances & Solid Insulation)	-	500	Testing charges
28(Screws & Connections)	-	500	Testing charges
27(Provision For Earthing)	-	500	Testing charges
26(Terminals For External Conductors)	-	500	Testing charges
25(Supply Connection & External Flexible Cords)	-	0	Testing charges
24(Components)	-	400	Testing charges
23(Internal wiring)	-	500	Testing charges
22(Construction)	-	800	Testing charges
21(Mechanical strength)	-	400	Testing charges
20(Stability & Mechanical Hazards)	-	400	Testing charges
19(Abnormal Operation)	-	400	Testing charges
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	400	Testing charges
16(Leakage Current and Electric Strength)	-	300	Testing charges
15(Moisture Resistance)	-	600	Testing charges
14(Transient Over Voltage)	-	800	Testing charges
13(Leakage Current and Electric Strength at Operating Temperature)	-	500	Testing charges
11(Temperature Rise/ Heating)	-	300	Testing charges
10(Power Input & Current)	-	500	Testing charges
9(Starting Of Motor Operated Appliances)	-	0	Testing charges

-
Included w.e.f. 17.11.2023. Exclusion: Cl.19.11.4.1 to 19.11.4.7 (EMI/EMC), Cl.24.1.1, 24.1.2, 24.1.5 (Components)

IS 302 : Part 2 : Sec 14 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 14 electric kitchen machines (First Revision)

12000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
14(Transient Over Voltages, IS 302-1)	-	0	-
15.1(Moisture Resistance, IS 302-1)	-	0	-
15.2(Moisture Resistance, IS 302-1)	-	0	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	0	-
19.7(Abnormal Operation, IS 302-1)	-	0	-
19.101(Abnormal Operation)	-	0	-
27(Provision for Earthing)	-	0	-
15(Moisture Resistance, IS 302-1)	-	0	-
6(Classification- IS 302-1 )	-	-	-
6(Classification- IS 302-1)	-	-	-
7.1(Marking- IS 302-1)	-	-	-
7.1(Marking- IS 302-1)	-	-	-
7.1(Marking- IS 302-1)	-	-	-
7.1(Marking- IS 302-1)	-	-	-
7.1(Marking- IS 302-1)	-	-	-
7.1(Marking- IS 302-1)	-	-	-
7.1(Marking- IS 302-1)	-	-	-
7.1(Marking- IS 302-1)	-	-	-
7.3(Marking- IS 302-1)	-	-	-
7.4(Marking- IS 302-1)	-	-	-
7.6(Marking- IS 302-1)	-	-	-
7.7(Marking- IS 302-1)	-	-	-
7.8(Marking- IS 302-1)	-	-	-
7.11(Marking- IS 302-1)	-	-	-
7.12(Marking- IS 302-1)	-	-	-
7.13(Marking- IS 302-1)	-	-	-
7.14(Marking- IS 302-1)	-	-	-
7.15(Marking- IS 302-1)	-	-	-
7.101(Marking)	-	-	-
8( Protection Against Electric Shock, IS 302-1)	-	-	-
10(Power Input and Current, IS 302-1)	-	-	-
11(Heating, IS 302-1)	-	-	-
11(Heating, IS 302-1)	-	-	-
11(Heating, IS 302-1)	-	-	-
11(Heating, IS 302-1)	-	-	-
11(Heating, IS 302-1)	-	-	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	-	-
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	-	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	-	-
19.8(Abnormal Operation, IS 302-1)	-	-	-
19.9(Abnormal Operation, IS 302-1)	-	-	-
19.1(Abnormal Operation, IS 302-1)	-	-	-
19.102(Abnormal Operation)	-	-	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	-	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	-	-
20.101(Stability & Mechanical Hazards)	-	-	-
20.102(Stability & Mechanical Hazards)	-	-	-
20.103(Stability & Mechanical Hazards)	-	-	-
20.104(Stability & Mechanical Hazards)	-	-	-
20.105(Stability & Mechanical Hazards)	-	-	-
20.106(Stability & Mechanical Hazards)	-	-	-
20.107(Stability & Mechanical Hazards)	-	-	-
20.108(Stability & Mechanical Hazards)	-	-	-
20.109(Stability & Mechanical Hazards)	-	-	-
20.110(Stability & Mechanical Hazards)	-	-	-
20.111(Stability & Mechanical Hazards)	-	-	-
20.112(Stability & Mechanical Hazards)	-	-	-
20.113(Stability & Mechanical Hazards)	-	-	-
20.114(Stability & Mechanical Hazards)	-	-	-
20.115(Stability & Mechanical Hazards)	-	-	-
20.116(Stability & Mechanical Hazards)	-	-	-
21.1(Mechanical Strength, IS 302-1)	-	-	-
21.2(Mechanical Strength, IS 302-1)	-	-	-
22(Construction, IS 302-1)	-	-	-
22.101(Construction)	-	-	-
22.102(Construction)	-	-	-
23.1(Internal Wiring, IS 302-1)	-	-	-
23.2(Internal Wiring, IS 302-1)	-	-	-
23.3(Internal Wiring, IS 302-1)	-	-	-
23.4(Internal Wiring, IS 302-1)	-	-	-
23.5(Internal Wiring, IS 302-1)	-	-	-
23.6(Internal Wiring, IS 302-1)	-	-	-
23.7(Internal Wiring, IS 302-1)	-	-	-
23.8(Internal Wiring, IS 302-1)	-	-	-
23.9(Internal Wiring, IS 302-1)	-	-	-
23.10(Internal Wiring, IS 302-1)	-	-	-
24.1(Components, IS 302-1)	-	-	-
24.2(Components, IS 302-1)	-	-	-
24.5(Components, IS 302-1)	-	-	-
24.6(Components, IS 302-1)	-	-	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	-	-
26(Terminals for External Conductors, IS 302-1)	-	-	-
27(Provision for Earthing, IS 302-1)	-	-	-
27.2(Provision for Earthing, IS 302-1)	-	-	-
27.3(Provision for Earthing, IS 302-1)	-	-	-
27.4(Provision for Earthing, IS 302-1)	-	-	-
27.5(Provision for Earthing, IS 302-1)	-	-	-
28(Screws & Connections, IS 302-1)	-	-	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	-	-
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	-	-
30.1(Resistance to Heat and Fire, IS 302-1)	-	-	-
30.2(Resistance to Heat and Fire, IS 302-1)	-	-	-
31(Resistance of Rusting, IS 302-1)	-	-	-
32(Radiation, Toxicity and similar Hazard IS 302-1)	-	-	-

-
Included w.e.f. 17.11.2023. Exclusion: Cl 19.11.4.1 to 19.11.4.7 (EMI/EMC Tests), Cl 24.1. 1,24.1.2 & 24.1.5 (Components)

IS 7809 : Part 3 : Sec 1 (1986)

Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 3 requirements or individual materials: Sec 1 plasticized polyvinylchloride tapes with non - Thermosetting adhesive (First Revision)

19400.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
2.1.1(Type and Desiganation)	-	10	-
2.1.2(Type and Desiganation)	-	10	-
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	10	-
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	10	-
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	10	-
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	10	-
4.1(Performance Requirments)	-	0	-
4.2(Performance Requirments)	-	0	-
4.3(Performance Requirments)	-	0	-
4.4(Performance Requirments)	-	0	-
4.5(Performance Requirments)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	500	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.7(Electrolytic corrosion)	-	3000	-
4.7(Electrolytic corrosion)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.8(Stability to accelerated ageing )	-	800	-
4.9(Insulation resistance test)	-	750	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	10	-
2.1.1(Type and Desiganation)	-	10	-
2.1.2(Type and Desiganation)	-	10	-
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	10	-
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	10	-
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	10	-
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	10	-
4.1(Performance Requirments)	-	0	-
4.2(Performance Requirments)	-	0	-
4.3(Performance Requirments)	-	0	-
4.4(Performance Requirments)	-	0	-
4.5(Performance Requirments)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.8(Stability to accelerated ageing )	-	800	-
4.9(Insulation resistance test)	-	750	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Appearance)	-	1000	-
3.1(Freedom from defects)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	1000	-
Cl.No.4 of IS 7809 (Part 1)-1975(Appearance)	-	500	-
Cl.No.5 of IS 7809 (Part 1)-1975(Freedom From Deffects)	-	50	-
Cl.No.3.2(Width)	-	250	-
Cl.No.3.3(Length)	-	250	-
Cl.No.3.4(Thickness)	-	250	-
Cl.No.4.1(Tensile Strength)	-	750	-
Cl.No.4.2(Adhesion to Steel)	-	750	-
Cl.No.4.3(Adhesion to backing)	-	750	-
Cl.No.4.4(Electric Strength at RT)	-	750	-
Cl.No.4.5(Electric Strength after Humid Conditioning)	-	750	-
Cl.No.4.6(Flammability)	-	0	-
Cl.No.4.7()	-	0	-
Cl.No.4.8(Stability to accelerated ageing)	-	0	-
Cl.No.4.9(Insulation Resistance)	-	0	-
Cl.No.7 of IS 7809 (Part 1)-1975(Minimum Storage Life)	-	1000	-
Cl.No.4 of IS 7809 (Part 1)-1975(Appearance after minimum storage Life)	-	1000	-
Cl.No.5 of IS 7809 (Part 1)-1975(Freedom From Deffects after minimum storage Life)	-	0	-
Cl.No.3.2(Width after minimum storage Life)	-	0	-
Cl.No.3.3(Length after minimum storage Life)	-	0	-
Cl.No.3.4(Thickness after minimum storage Life)	-	0	-
Cl.No.4.1(Tensile Strength after minimum storage Life)	-	0	-
Cl.No.4.2(Adhesion to Steel after minimum storage Life)	-	0	-
Cl.No.4.3(Adhesion to backing after minimum storage Life)	-	0	-
Cl.No.4.4(Electric Strength at RT after minimum storage Life)	-	0	-
Cl.No.4.5(Electric Strength after Humid Conditioning after minimum storage Life)	-	0	-
Cl.No.4.6(Flammability after minimum storage Life)	-	0	-
Cl.No.4.7(Electrolytic Corrosion after minimum storage Life)	-	0	-
Cl.No.4.8(Stability to accelerated ageing after minimum storage Life)	-	0	-
Cl.No.4.9(Insulation Resistance after minimum storage Life)	-	0	-
3.1(Marking)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
2.1.1(Type and Desiganation)	-	0	-
2.1.2(Type and Desiganation)	-	0	-
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	0	-
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	0	-
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	0	-
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	0	-
4.1(Performance Requirments)	-	0	-
4.2(Performance Requirments)	-	0	-
4.3(Performance Requirments)	-	0	-
4.4(Performance Requirments)	-	0	-
4.5(Performance Requirments)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.8(Stability to accelerated ageing )	-	0	-
4.9(Insulation resistance test)	-	0	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	0	-
2.1.1(Type and Desiganation)	-	0	-
2.1.2(Type and Desiganation)	-	0	-
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	0	-
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	0	-
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	0	-
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	0	-
4.1(Performance Requirments)	-	0	-
4.2(Performance Requirments)	-	0	-
4.3(Performance Requirments)	-	0	-
4.4(Performance Requirments)	-	0	-
4.5(Performance Requirments)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.7(Electrolytic corrosion)	-	0	-
4.8(Stability to accelerated ageing )	-	0	-
4.9(Insulation resistance test)	-	0	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Appearance)	-	0	-
3.1(Freedom from defects)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	0	-
Cl.No.4 of IS 7809 (Part 1)-1975(Appearance)	-	0	-
Cl.No.5 of IS 7809 (Part 1)-1975(Freedom From Deffects)	-	0	-
Cl.No.3.2(Width)	-	0	-
Cl.No.3.3(Length)	-	0	-
Cl.No.3.4(Thickness)	-	0	-
Cl.No.4.1(Tensile Strength)	-	0	-
Cl.No.4.2(Adhesion to Steel)	-	0	-
Cl.No.4.3(Adhesion to backing)	-	0	-
Cl.No.4.4(Electric Strength at RT)	-	0	-
Cl.No.4.5(Electric Strength after Humid Conditioning)	-	0	-
Cl.No.4.6(Flammability)	-	0	-
Cl.No.4.7()	-	0	-
Cl.No.4.8(Stability to accelerated ageing)	-	0	-
Cl.No.4.9(Insulation Resistance)	-	0	-
Cl.No.7 of IS 7809 (Part 1)-1975(Minimum Storage Life)	-	0	-
Cl.No.4 of IS 7809 (Part 1)-1975(Appearance after minimum storage Life)	-	0	-
Cl.No.5 of IS 7809 (Part 1)-1975(Freedom From Deffects after minimum storage Life)	-	0	-
Cl.No.3.2(Width after minimum storage Life)	-	0	-
Cl.No.3.3(Length after minimum storage Life)	-	0	-
Cl.No.3.4(Thickness after minimum storage Life)	-	0	-
Cl.No.4.1(Tensile Strength after minimum storage Life)	-	0	-
Cl.No.4.2(Adhesion to Steel after minimum storage Life)	-	0	-
Cl.No.4.3(Adhesion to backing after minimum storage Life)	-	0	-
Cl.No.4.4(Electric Strength at RT after minimum storage Life)	-	0	-
Cl.No.4.5(Electric Strength after Humid Conditioning after minimum storage Life)	-	0	-
Cl.No.4.6(Flammability after minimum storage Life)	-	0	-
Cl.No.4.7(Electrolytic Corrosion after minimum storage Life)	-	0	-
Cl.No.4.8(Stability to accelerated ageing after minimum storage Life)	-	0	-
Cl.No.4.9(Insulation Resistance after minimum storage Life)	-	0	-
3.1(Marking)	-	0	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
2.1.1(Type and Desiganation)	-	-	-
2.1.2(Type and Desiganation)	-	-	-
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	-	-
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	-	-
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	-	-
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	-	-
4.1(Performance Requirments)	-	-	-
4.2(Performance Requirments)	-	-	-
4.3(Performance Requirments)	-	-	-
4.4(Performance Requirments)	-	-	-
4.5(Performance Requirments)	-	-	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	-	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	-	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	-	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	-	-
4.7(Electrolytic corrosion)	-	-	-
4.7(Electrolytic corrosion)	-	-	-
4.7(Electrolytic corrosion)	-	-	-
4.8(Stability to accelerated ageing )	-	-	-
4.9(Insulation resistance test)	-	-	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	-	-
2.1.1(Type and Desiganation)	-	-	-
2.1.2(Type and Desiganation)	-	-	-
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	-	-
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	-	-
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	-	-
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	-	-
4.1(Performance Requirments)	-	-	-
4.2(Performance Requirments)	-	-	-
4.3(Performance Requirments)	-	-	-
4.4(Performance Requirments)	-	-	-
4.5(Performance Requirments)	-	-	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	-	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	-	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	-	-
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	-	-
4.7(Electrolytic corrosion)	-	-	-
4.7(Electrolytic corrosion)	-	-	-
4.7(Electrolytic corrosion)	-	-	-
4.8(Stability to accelerated ageing )	-	-	-
4.9(Insulation resistance test)	-	-	-
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Appearance)	-	-	-
3.1(Freedom from defects)	-	-	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
3.1(Minimum Storage Life ,Dimensions , Cl. 7.1 of IS 7809(Part 1) :1975)	-	-	-
Cl.No.4 of IS 7809 (Part 1)-1975(Appearance)	-	-	-
Cl.No.5 of IS 7809 (Part 1)-1975(Freedom From Deffects)	-	-	-
Cl.No.3.2(Width)	-	-	-
Cl.No.3.3(Length)	-	-	-
Cl.No.3.4(Thickness)	-	-	-
Cl.No.4.1(Tensile Strength)	-	-	-
Cl.No.4.2(Adhesion to Steel)	-	-	-
Cl.No.4.3(Adhesion to backing)	-	-	-
Cl.No.4.4(Electric Strength at RT)	-	-	-
Cl.No.4.5(Electric Strength after Humid Conditioning)	-	-	-
Cl.No.4.6(Flammability)	-	-	-
Cl.No.4.7()	-	-	-
Cl.No.4.8(Stability to accelerated ageing)	-	-	-
Cl.No.4.9(Insulation Resistance)	-	-	-
Cl.No.7 of IS 7809 (Part 1)-1975(Minimum Storage Life)	-	-	-
Cl.No.4 of IS 7809 (Part 1)-1975(Appearance after minimum storage Life)	-	-	-
Cl.No.5 of IS 7809 (Part 1)-1975(Freedom From Deffects after minimum storage Life)	-	-	-
Cl.No.3.2(Width after minimum storage Life)	-	-	-
Cl.No.3.3(Length after minimum storage Life)	-	-	-
Cl.No.3.4(Thickness after minimum storage Life)	-	-	-
Cl.No.4.1(Tensile Strength after minimum storage Life)	-	-	-
Cl.No.4.2(Adhesion to Steel after minimum storage Life)	-	-	-
Cl.No.4.3(Adhesion to backing after minimum storage Life)	-	-	-
Cl.No.4.4(Electric Strength at RT after minimum storage Life)	-	-	-
Cl.No.4.5(Electric Strength after Humid Conditioning after minimum storage Life)	-	-	-
Cl.No.4.6(Flammability after minimum storage Life)	-	-	-
Cl.No.4.7(Electrolytic Corrosion after minimum storage Life)	-	-	-
Cl.No.4.8(Stability to accelerated ageing after minimum storage Life)	-	-	-
Cl.No.4.9(Insulation Resistance after minimum storage Life)	-	-	-
3.1(Marking)	-	-	-

-
Included w.e.f. 17.11.2023

IS 4289 : Part 2 (2000)

Flexible cables for lifts and other flexible connections - Specification: Part 2 pvc insulated circular cables

21000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor)	-	2000	-
5(Separator)	-	100	-
6(Insulation)	-	2500	-
7(Central heart)	-	100	-
8(Fillers)	-	100	-
9(tape)	-	100	-
10(braid)	-	100	-
11(sheath)	-	100	-
12(GENERAL DETAILS OF CONSTRUCTION)	-	100	-
13(Construction- Conductor)	-	100	-
14(Construction- Insulation)	-	100	-
14.2(Thickness of Insulation)	-	500	-
14.3(Tolerance on Thickness of Insulation)	-	500	-
15(Core identification)	-	100	-
16(Core assembly)	-	100	-
17(overall covering)	-	100	-
17.1.1(Thickness of Sheath)	-	100	-
17.1.2(Tolerance on Thickness of Sheath)	-	500	-
4(Conductor)	-	0	-
5(Separator)	-	0	-
6(Insulation)	-	0	-
7(Central heart)	-	0	-
8(Fillers)	-	0	-
9(tape)	-	0	-
10(braid)	-	0	-
11(sheath)	-	0	-
12(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
13(Construction- Conductor)	-	0	-
14(Construction- Insulation)	-	0	-
14.2(Thickness of Insulation)	-	0	-
14.3(Tolerance on Thickness of Insulation)	-	0	-
15(Core identification)	-	0	-
16(Core assembly)	-	0	-
17(overall covering)	-	0	-
17.1.1(Thickness of Sheath)	-	0	-
17.1.2(Tolerance on Thickness of Sheath)	-	0	-
18.1.a.i(IS 10810 Part-1)	-	0	-
18.1.a.ii(IS 10810 Part-5)	-	0	-
18.1.b(IS 10810 Part-6)	-	0	-
18.1.c.i(IS 10810 Part-7)	-	0	-
18.1.c.i(IS 10810 Part-7)	-	0	-
18.1.c.ii(IS 10810 Part-11)	-	0	-
18.1.c.ii(IS 10810 Part-11)	-	0	-
18.1.c.iii(IS 10810 Part-10)	-	0	-
18.1.c.iii(IS 10810 Part-10)	-	0	-
18.1.c.iv(IS 10810 Part-14)	-	0	-
18.1.c.iv(IS 10810 Part-14)	-	0	-
18.1.c.v(IS 10810 Part-12)	-	0	-
18.1.c.v(IS 10810 Part-12)	-	0	-
18.1.c.vi(IS 10810 Part-60)	-	0	-
18.1.c.vi(IS 10810 Part-60)	-	0	-
18.1.d(IS 10810 Part-45)	-	0	-
18.1.e(IS 10810 Part-43)	-	0	-
18.1. f(IS 10810 Part-54)	-	0	-
18.1.g(IS 10810 Part-53)	-	0	-

-
Included w.e.f. 17.11.2023

IS 4289 : Part 1 (1984)

Specification for flexible cables for lifts and other flexible connections: Part 1 elastomer insulated cables (First Revision)

30000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Conductor)	-	100	-
4(Separator)	-	100	-
5(Insulation)	-	100	-
5(Central heart)	-	100	-
7(Fillers)	-	100	-
8(Proofed tape)	-	100	-
9(Braid)	-	100	-
10(Sheath)	-	100	-
11(GENERAL DETAILS OF CONSTRUCTION)	-	100	-
12(Conductor)	-	100	-
13(Insulation)	-	100	-
14(Core identification)	-	100	-
15(Core assembly)	-	100	-
16.1(Overall covering- sheathed cables)	-	100	-
16.2(overall covering- braided cables)	-	100	-
17.1.a(Persulphate test)	-	0	-
17.1.b(Annealing test)	-	0	-
17.1.c(Conductor resistance test)	-	0	-
17.1.d(Test for thickness of insulation and sheath)	-	0	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	0	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	0	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	0	-
17.1.f.4(Tear resistance)	-	0	-
17.1.g(High voltage water immersion test)	-	0	-
17.1.h(Insulation resistance test)	-	0	-
17.1.j(Static flexibility test)	-	0	-
17.1.k(Flammability test)	-	0	-
17.1.a(Persulphate test)	-	1500	-
17.1.b(Annealing test)	-	1000	-
17.1.c(Conductor resistance test)	-	2000	-
17.1.d(Test for thickness of insulation and sheath)	-	1000	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	1000	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	1000	-
17.1.e.2(Ageing in air oven for insulation)	-	3500	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	3500	-
17.1.f.2(Ageing in air bomb for sheath)	-	3000	-
17.1.f.3(Oil resistance for sheath)	-	3000	-
17.1.f.4(Tear resistance)	-	1500	-
17.1.g(High voltage water immersion test)	-	2000	-
17.1.h(Insulation resistance test)	-	2500	-
17.1.j(Static flexibility test)	-	1500	-
17.1.k(Flammability test)	-	500	-
3(Conductor)	-	0	-
4(Separator)	-	0	-
5(Insulation)	-	0	-
5(Central heart)	-	0	-
7(Fillers)	-	0	-
8(Proofed tape)	-	0	-
9(Braid)	-	0	-
10(Sheath)	-	0	-
11(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
12(Conductor)	-	0	-
13(Insulation)	-	0	-
14(Core identification)	-	0	-
15(Core assembly)	-	0	-
16.1(Overall covering- sheathed cables)	-	0	-
16.2(overall covering- braided cables)	-	0	-
17.1.a(Persulphate test)	-	0	-
17.1.b(Annealing test)	-	0	-
17.1.c(Conductor resistance test)	-	0	-
17.1.d(Test for thickness of insulation and sheath)	-	0	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	0	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	0	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	0	-
17.1.f.4(Tear resistance)	-	0	-
17.1.g(High voltage water immersion test)	-	0	-
17.1.h(Insulation resistance test)	-	0	-
17.1.j(Static flexibility test)	-	0	-
17.1.k(Flammability test)	-	0	-
17.1.a(Persulphate test)	-	0	-
17.1.b(Annealing test)	-	0	-
17.1.c(Conductor resistance test)	-	0	-
17.1.d(Test for thickness of insulation and sheath)	-	0	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	0	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	0	-
17.1.e.2(Ageing in air oven for insulation)	-	0	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	0	-
17.1.f.2(Ageing in air bomb for sheath)	-	0	-
17.1.f.3(Oil resistance for sheath)	-	0	-
17.1.f.4(Tear resistance)	-	0	-
17.1.g(High voltage water immersion test)	-	0	-
17.1.h(Insulation resistance test)	-	0	-
17.1.j(Static flexibility test)	-	0	-
17.1.k(Flammability test)	-	0	-

-
Included w.e.f. 17.11.2023

IS 5950 (1984)

Specification for shot firing cables (For Use Other Than In Shafts) (First Revision)

10000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Conductor : Material -IS : 8130-2013)	-	50	-
4.1(Insulation : Material -IS : 5831-1984)	-	50	-
5.1(Sheath : materail IS : 5831-1984)	-	50	-
6.1(Conductor : Construction IS : 8130-2013)	-	50	-
7.1(Insulation : Application )	-	50	-
7.2(Thickness of Insulation - average )	-	50	-
7.2(Thickness of Insulation - Min. )	-	375	-
7.3(Colour of Insulation)	-	50	-
8.1, 9.1 (c)(Nominal radial thickness of sheath)	-	50	-
8.2(Thickness of Sheath)	-	375	-
8.2(Thickness of Sheath - min.)	-	375	-
8.3(Colour of Sheath)	-	50	-
9.1 a)(Annealing test)	-	500	-
9.1 b)(Conductor resistance test)	-	1000	-
9.1 d) i)(Insulation : Tensile strength)	-	500	-
9.1 d) i)(Insulation : elongation at break)	-	500	-
9.1 d) i)(Sheath : Tensile strength)	-	500	-
9.1 d) i)(Sheath : elongation at break)	-	500	-
9.1 d) ii)(Ageing in air oven - Insulation : Tensile strength)	-	250	-
9.1 d) ii)(Ageing in air oven - Insulation : Tensile strength Variation)	-	250	-
9.1 d) ii)(Ageing in air oven - Insulation : elongation at break)	-	250	-
9.1 d) ii)(Ageing in air oven - Insulation : elongation variation at break)	-	250	-
9.1 d) ii)(Ageing in air oven - Sheath : Tensile strength)	-	250	-
9.1 d) ii)(Ageing in air oven - Sheath : Tensile strength variation )	-	250	-
9.1 d) ii)(Ageing in air oven - Sheath : elongation at break)	-	250	-
9.1 d) ii)(Ageing in air oven - Sheath : elongation variation at break)	-	250	-
9.1 d) iii )(Loss of mass test - insulation )	-	500	-
9.1 d) iii )(Loss of mass test - Sheath )	-	500	-
9.1 d) iv )(Hot deformation - insulation )	-	500	-
9.1 d) iv )(Hot deformation - sheath )	-	500	-
9.1 d) v )(Heat shock - insulation )	-	250	-
9.1 d) v )(Heat shock - Sheath )	-	250	-
9.1 d) vi )(Shrinkage - insulation )	-	250	-
9.1 d) vi )(Shrinkage : Crack observed - insulation )	-	250	-
9.1 d) vi )(Shrinkage - Sheath )	-	250	-
9.1 d) vi )(Shrinkage: Crack observed - Sheath )	-	250	-
10.2(Voltage test )	-	1000	-
9.1 f)(Insulation resistance test: Volume resistivity )	-	500	-
9.1 f)(Insulation resistance test : IR constant)	-	500	-
10.4(Flammability Test )	-	500	-
11.1(Manufacturer’s Identification)	-	50	-
11.2(Cable Code)	-	50	-
12.1(packing )	-	50	-
12.2(Marking )	-	50	-
12.2.1(Standard marks )	-	50	-
3.1(Conductor : Material -IS : 8130-2013)	-	0	-
4.1(Insulation : Material -IS : 5831-1984)	-	0	-
5.1(Sheath : materail IS : 5831-1984)	-	0	-
6.1(Conductor : Construction IS : 8130-2013)	-	0	-
7.1(Insulation : Application )	-	0	-
7.2(Thickness of Insulation - average )	-	0	-
7.2(Thickness of Insulation - Min. )	-	0	-
7.3(Colour of Insulation)	-	0	-
8.1, 9.1 (c)(Nominal radial thickness of sheath)	-	0	-
8.2(Thickness of Sheath)	-	0	-
8.2(Thickness of Sheath - min.)	-	0	-
8.3(Colour of Sheath)	-	0	-
9.1 a)(Annealing test)	-	0	-
9.1 b)(Conductor resistance test)	-	0	-
9.1 d) i)(Insulation : Tensile strength)	-	0	-
9.1 d) i)(Insulation : elongation at break)	-	0	-
9.1 d) i)(Sheath : Tensile strength)	-	0	-
9.1 d) i)(Sheath : elongation at break)	-	0	-
9.1 d) ii)(Ageing in air oven - Insulation : Tensile strength)	-	0	-
9.1 d) ii)(Ageing in air oven - Insulation : Tensile strength Variation)	-	0	-
9.1 d) ii)(Ageing in air oven - Insulation : elongation at break)	-	0	-
9.1 d) ii)(Ageing in air oven - Insulation : elongation variation at break)	-	0	-
9.1 d) ii)(Ageing in air oven - Sheath : Tensile strength)	-	0	-
9.1 d) ii)(Ageing in air oven - Sheath : Tensile strength variation )	-	0	-
9.1 d) ii)(Ageing in air oven - Sheath : elongation at break)	-	0	-
9.1 d) ii)(Ageing in air oven - Sheath : elongation variation at break)	-	0	-
9.1 d) iii )(Loss of mass test - insulation )	-	0	-
9.1 d) iii )(Loss of mass test - Sheath )	-	0	-
9.1 d) iv )(Hot deformation - insulation )	-	0	-
9.1 d) iv )(Hot deformation - sheath )	-	0	-
9.1 d) v )(Heat shock - insulation )	-	0	-
9.1 d) v )(Heat shock - Sheath )	-	0	-
9.1 d) vi )(Shrinkage - insulation )	-	0	-
9.1 d) vi )(Shrinkage : Crack observed - insulation )	-	0	-
9.1 d) vi )(Shrinkage - Sheath )	-	0	-
9.1 d) vi )(Shrinkage: Crack observed - Sheath )	-	0	-
10.2(Voltage test )	-	0	-
9.1 f)(Insulation resistance test: Volume resistivity )	-	0	-
9.1 f)(Insulation resistance test : IR constant)	-	0	-
10.4(Flammability Test )	-	0	-
11.1(Manufacturer’s Identification)	-	0	-
11.2(Cable Code)	-	0	-
12.1(packing )	-	0	-
12.2(Marking )	-	0	-
12.2.1(Standard marks )	-	0	-

-
Included w.e.f. 17.11.2023

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

9000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	50	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	50	-
5.1(Insulation)	-	50	-
6.1(Flexibility class)	-	50	-
6.2(Compactness)	-	50	-
6.2(No of strands)	-	50	-
6.2(Surface)	-	50	-
6.3(Protective barrier)	-	50	-
6.4(size of street lighting conductor)	-	50	-
6.5(Size of messenger conductor )	-	50	-
6.6(Joints in messenger conductor )	-	50	-
6.6(Direction of outer layer)	-	50	-
7.1(Insulation)	-	50	-
7.2( Thickness of insulation)	-	250	-
7.3(Tolerance on thickness of insulation )	-	250	-
7.4(Aplication of the insulation )	-	50	-
7.5(Colour of the insulation )	-	50	-
8.1(Core identification)	-	50	-
8.2(Core identification)	-	50	-
8.3(Identification by other means)	-	50	-
9.1(Assembly (Laying up))	-	50	-
9.2(Assembly (Laying up))	-	50	-
9.3(Direction of lay)	-	50	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	500	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	250	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1000	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	500	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	1000	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	500	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	500	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	500	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	250	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	250	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	200	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	200	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	1500	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	250	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	250	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	500	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	500	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	500	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	250	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	250	-
10.1 g)(High voltage test - IS10810:Part 45)	-	500	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	2000	-
11.4(Bending Test on the Completed Cable ( Optional))	-	2000	-
4.1(Phase/Street Lighting conductor)	-	0	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	0	-
5.1(Insulation)	-	0	-
6.1(Flexibility class)	-	0	-
6.2(Compactness)	-	0	-
6.2(No of strands)	-	0	-
6.2(Surface)	-	0	-
6.3(Protective barrier)	-	0	-
6.4(size of street lighting conductor)	-	0	-
6.5(Size of messenger conductor )	-	0	-
6.6(Joints in messenger conductor )	-	0	-
6.6(Direction of outer layer)	-	0	-
7.1(Insulation)	-	0	-
7.2( Thickness of insulation)	-	0	-
7.3(Tolerance on thickness of insulation )	-	0	-
7.4(Aplication of the insulation )	-	0	-
7.5(Colour of the insulation )	-	0	-
8.1(Core identification)	-	0	-
8.2(Core identification)	-	0	-
8.3(Identification by other means)	-	0	-
9.1(Assembly (Laying up))	-	0	-
9.2(Assembly (Laying up))	-	0	-
9.3(Direction of lay)	-	0	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	0	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	0	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	0	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	0	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	0	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	0	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	0	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	0	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	0	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	0	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	0	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	0	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	0	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	0	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	0	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	0	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	0	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	0	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	0	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	0	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	0	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	0	-
10.1 g)(High voltage test - IS10810:Part 45)	-	0	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	0	-
11.4(Bending Test on the Completed Cable ( Optional))	-	0	-
10.1 d) iii)(Carbon Black Content)	-	0	-

-
Included w.e.f. 17.11.2023

IS 8784 (1987)

Specification for thermocouple compensating cables (Second Revision)

20000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Type of thermocouple)	-	50	-
4.1(Conductor)	-	50	-
5(INSULATION AND SHEATH)	-	50	-
6(ARMOURING)	-	4550	-
7(SHIELDING)	-	50	-
8.1(NOISE REDUCTION: Drain Wire)	-	50	-
8.2(NOISE REDUCTION)	-	50	-
9.1(DIMENSION : Single Wire)	-	50	-
9.1.1(DIMENSION : Single Wire (Tolerances))	-	50	-
9.1.2(DIMENSION : Single Wire (Ovality))	-	50	-
9.2.1(Thickness of Insulation )	-	750	-
9.2.2(Thickness of Sheath )	-	750	-
9.3(Dimension of cable )	-	750	-
10.1(Colour Code )	-	50	-
11.1(ENVIRONMENTS FOR USE OF DIFFERENT THERMOCOUPLE COMPENSATING CABLES)	-	50	-
12.1(INFORMATION TO BE SUPPLIED BY THE MANUFACTURER)	-	50	-
13.1(PACKING AND MARKING)	-	50	-
13.2(PACKING AND MARKING)	-	50	-
13.2.1(Standard Mark)	-	50	-
14.2(Thermal emf Test )	-	7000	-
14.3(Resistance Test)	-	2000	-
14.4.1( Thickness of Insulation)	-	750	-
14.4.2.1( Thickness of Sheath : Round )	-	750	-
14.4.2.2( Thickness of Sheath : Oval )	-	750	-
14.5(Insulation Resistance Test :Volume resistivity ( Before High Voltage test ))	-	750	-
15.5(Insulation Resistance Test :Insulation resistance constant ( Before High Voltage test ))	-	750	-
14.5(Insulation Resistance Test: Volume resistivity ( After High Voltage test ))	-	750	-
15.5(Insulation Resistance Test: Insulation Resisatnce constant ( After High Voltage test ))	-	750	-
14.6(Drain Wire Continuity Test )	-	500	-
14.7(H.V. Test )	-	1500	-
14.8(Heat Shock Test)	-	800	-
3.1(Type of thermocouple)	-	0	-
4.1(Conductor)	-	0	-
5(INSULATION AND SHEATH)	-	0	-
6(ARMOURING)	-	0	-
7(SHIELDING)	-	0	-
8.1(NOISE REDUCTION: Drain Wire)	-	0	-
8.2(NOISE REDUCTION)	-	0	-
9.1(DIMENSION : Single Wire)	-	0	-
9.1.1(DIMENSION : Single Wire (Tolerances))	-	0	-
9.1.2(DIMENSION : Single Wire (Ovality))	-	0	-
9.2.1(Thickness of Insulation )	-	0	-
9.2.2(Thickness of Sheath )	-	0	-
9.3(Dimension of cable )	-	0	-
10.1(Colour Code )	-	0	-
11.1(ENVIRONMENTS FOR USE OF DIFFERENT THERMOCOUPLE COMPENSATING CABLES)	-	0	-
12.1(INFORMATION TO BE SUPPLIED BY THE MANUFACTURER)	-	0	-
13.1(PACKING AND MARKING)	-	0	-
13.2(PACKING AND MARKING)	-	0	-
13.2.1(Standard Mark)	-	0	-
14.2(Thermal emf Test )	-	0	-
14.3(Resistance Test)	-	0	-
14.4.1( Thickness of Insulation)	-	0	-
14.4.2.1( Thickness of Sheath : Round )	-	0	-
14.4.2.2( Thickness of Sheath : Oval )	-	0	-
14.5(Insulation Resistance Test :Volume resistivity ( Before High Voltage test ))	-	0	-
15.5(Insulation Resistance Test :Insulation resistance constant ( Before High Voltage test ))	-	0	-
14.5(Insulation Resistance Test: Volume resistivity ( After High Voltage test ))	-	0	-
15.5(Insulation Resistance Test: Insulation Resisatnce constant ( After High Voltage test ))	-	0	-
14.6(Drain Wire Continuity Test )	-	0	-
14.7(H.V. Test )	-	0	-
14.8(Heat Shock Test)	-	0	-
14.1.1, f)(Test for armour wires)	-	0	-

-
Included w.e.f. 17.11.2023

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

195000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	100	-
4.1.1 b) (Material : Seperator tape )	-	100	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	100	-
4.1.1 e) (Shape of conductor )	-	100	-
4.1.1 f) (Nominal size of conductor )	-	100	-
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	100	-
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	100	-
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	200	-
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	500	-
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	2500	-
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	2500	-
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	2500	-
4.2.5(Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	2500	-
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	2500	-
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	2500	-
4.3(Fillers)	-	1000	-
4.4(Binder Tape)	-	1000	-
4.5.1,13.4, 14.4(Sheath : Compound )	-	500	-
4.5.2, 13.4, 14.4(Sheath : Application)	-	500	-
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	500	-
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	500	-
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	0	-
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	0	-
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	0	-
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	0	-
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	0	-
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	0	-
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	500	-
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	1000	-
4.5.6, 13.4(Colour of Sheath)	-	1000	-
5.1(High Voltage Test (at Room Temperature))	-	5000	-
5.3(Flammability Test- IS 10810 (Part 53).)	-	5000	-
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	5000	-
5.5(Temperature Index-IS 10810 (Part 64).)	-	5000	-
5.6(Smoke Density-IS 10810 (Part 63).)	-	15000	-
5.7(Assessment of Halogen- Table 1 of Annex D)	-	40000	-
5.1(Persulphate Test- IS 10810 (Part 4).)	-	3000	-
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	5000	-
5.12(Hot Set Test- IS 10810 (Part 30).)	-	5000	-
5.12(Permanent Set - IS 10810 (Part 30).)	-	5000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	4000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-	4000	-
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	15000	-
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	5000	-
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	5000	-
6.1, Table 1(CORE IDENTIFICATION)	-	500	-
6.2.1(Preferred Arrangement of Marking)	-	250	-
6.2.2(Durability)	-	250	-
7.0(CABLE CODE)	-	1000	-
9.0( IDENTIFICATION)	-	1000	-
10.1(Packing )	-	100	-
10.2(marking)	-	100	-
10.2.1(Standards marking)	-	100	-
13.3, 14.3(assembly of cores )	-	1000	-
6.1(General Requirements)	-	100	-
6.1.1(Colour Combination Green Yellow)	-	100	-
12.1(Conductor)	-	1000	-
12.2, Table 4(insulation)	-	500	-
4.3.1 (e)(Fluorine content test (Fillers))	-	0	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	0	-
4.3.1 (c)(Conductivity test (Fillers))	-	0	-
4.3.1 (b)(pH test (Fillers))	-	0	-
4.3.1 (a)(HCl test (Fillers))	-	0	-
5.7 (a)(HCl test (Assessment of halogen test))	-	0	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	0	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	0	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	6000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	4000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	4000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	5000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	2500	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	1000	-
6.1, Table 1(CORE IDENTIFICATION)	-	0	-
6.1(General Requirements)	-	0	-
6.1.1(Colour Combination Green Yellow)	-	0	-
12.1(Conductor)	-	0	-
12.2, Table 4(insulation)	-	0	-
4.3.1 (e)(Fluorine content test (Fillers))	-	0	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	0	-
4.3.1 (c)(Conductivity test (Fillers))	-	0	-
4.3.1 (b)(pH test (Fillers))	-	0	-
4.3.1 (a)(HCl test (Fillers))	-	0	-
5.7 (a)(HCl test (Assessment of halogen test))	-	0	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	0	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	0	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	0	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	0	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	0	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	0	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	0	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	0	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	0	-

-
Included w.e.f. 17.11.2023. Exclusion: Cl.5.2 (Spark Test (Routine test)), Table-4 (Copper Purity test)

IS 2593 (1984)

Flexible Cables for Miners' Cap-lamps

35000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CONDUCTOR)	-	50	-
3.1.1(Per sulphate test )	-	2000	-
3.1.2(Resistance test )	-	2000	-
4.1(INSULATION)	-	50	-
6.1(SHEATH)	-	50	-
7.1(Construction : Conductor )	-	50	-
8.1(Thickness of Insulation - Average )	-	250	-
8.1(Thickness of Insulation - minimum)	-	250	-
9.1(IDENTIFICATION OF CORES)	-	50	-
10.1(LAYING UP)	-	50	-
11.1(SHEATH : Application )	-	50	-
11.2(Thickness of Sheath -average )	-	250	-
12.2(Thickness of Sheath - Minimum)	-	250	-
11.3(Coulor of sheath )	-	50	-
12.1(OVERALL DIAMETER)	-	500	-
13.1 b)(Annealing test)	-	500	-
13.1 e) 1)(Physical tests for insulation: Tensile strength )	-	750	-
13.1 e) 1)(Physical tests for insulation: elongation at break )	-	750	-
13.1 e) 1)(Physical tests for Sheath : Tensile strength )	-	750	-
13.1 e) 1)(Physical tests for Sheath: elongation at break )	-	750	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : Tensile Strength )	-	750	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : Tensile Strength variation )	-	750	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : elongation variation at break)	-	750	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : elongation variation at break)	-	750	-
13.1 e) 3)(Ageing in oxygen bomb ( for insulation ) : Tensile Strength variation )	-	1750	-
13.1 e) 3)(Ageing in oxygen bomb ( for insulation ) : elongation variation at break)	-	1750	-
13.1 e) 3)(Ageing in air bomb ( for sheath ) : Tensile Strength variation )	-	1750	-
13.1 e) 3)(Ageing in air bomb ( for sheath ) : elongation variation at break)	-	1750	-
13.1 e) 4)(Oil resistance test ( for sheath ) : Tensile strength variation )	-	1250	-
13.1 e) 4)(Oil resistance test ( for sheath ) : Elongation variation )	-	1250	-
14.1(Voltage test)	-	3000	-
14.2(Flammability test)	-	1000	-
14.3.1(Centre Strain Cord : Breaking Load )	-	50	-
14.3.2(Centre Strain Cord : Determination of Copper and Manganese Content)	-	50	-
14.4(Checking of overall diameter of cable)	-	0	-
14.5(Resistance of sheath to fatty acids : Weigth Increase )	-	750	-
14.5(Resistance of sheath to fatty acids : Diameter Increase )	-	750	-
15.1(MANUFACTURER'S IDENTIFICATION)	-	50	-
16.1(Packing )	-	50	-
16.2(Marking )	-	50	-
16.2.1(Standards Mark )	-	50	-
6.1(Resistance of Sheath to Fatty Acids - 14.5 - diameter increase)	-	0	-
6.1(Resistance of Sheath to Fatty Acids - 14.5 - weight increase)	-	0	-
5.1(Copper and Manganese Content - Cl 14.3.2)	-	50	-
3.1.1(mass of copper - Cl 7.1 of IS 8130 read with Method B of IS 10810 (Part 4))	-	0	-
3.1(CONDUCTOR)	-	0	-
3.1.1(Per sulphate test )	-	0	-
3.1.2(Resistance test )	-	0	-
4.1(INSULATION)	-	0	-
6.1(SHEATH)	-	0	-
7.1(Construction : Conductor )	-	0	-
8.1(Thickness of Insulation - Average )	-	0	-
8.1(Thickness of Insulation - minimum)	-	0	-
9.1(IDENTIFICATION OF CORES)	-	0	-
10.1(LAYING UP)	-	0	-
11.1(SHEATH : Application )	-	0	-
11.2(Thickness of Sheath -average )	-	0	-
12.2(Thickness of Sheath - Minimum)	-	0	-
11.3(Coulor of sheath )	-	0	-
12.1(OVERALL DIAMETER)	-	0	-
13.1 b)(Annealing test)	-	0	-
13.1 e) 1)(Physical tests for insulation: Tensile strength )	-	0	-
13.1 e) 1)(Physical tests for insulation: elongation at break )	-	0	-
13.1 e) 1)(Physical tests for Sheath : Tensile strength )	-	0	-
13.1 e) 1)(Physical tests for Sheath: elongation at break )	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : Tensile Strength )	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : Tensile Strength variation )	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : elongation variation at break)	-	0	-
13.1 e) 2)(Ageing in air oven ( for insulation ) : elongation variation at break)	-	0	-
13.1 e) 3)(Ageing in oxygen bomb ( for insulation ) : Tensile Strength variation )	-	0	-
13.1 e) 3)(Ageing in oxygen bomb ( for insulation ) : elongation variation at break)	-	0	-
13.1 e) 3)(Ageing in air bomb ( for sheath ) : Tensile Strength variation )	-	0	-
13.1 e) 3)(Ageing in air bomb ( for sheath ) : elongation variation at break)	-	0	-
13.1 e) 4)(Oil resistance test ( for sheath ) : Tensile strength variation )	-	0	-
13.1 e) 4)(Oil resistance test ( for sheath ) : Elongation variation )	-	0	-
14.1(Voltage test)	-	0	-
14.2(Flammability test)	-	0	-
14.3.1(Centre Strain Cord : Breaking Load )	-	0	-
14.3.2(Centre Strain Cord : Determination of Copper and Manganese Content)	-	0	-
14.4(Checking of overall diameter of cable)	-	0	-
14.5(Resistance of sheath to fatty acids : Weigth Increase )	-	0	-
14.5(Resistance of sheath to fatty acids : Diameter Increase )	-	0	-
15.1(MANUFACTURER'S IDENTIFICATION)	-	0	-
16.1(Packing )	-	0	-
16.2(Marking )	-	0	-
16.2.1(Standards Mark )	-	0	-

-
Included w.e.f. 17.11.2023. Exclusion: Cl.14.3.2 (Centre Strain Cord : Determination of Copper and Manganese Content)

IS 2465 (1984)

Specification for cables for motor vehicles (Second Revision)

15000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Insulation)	-	10	-
7.3(Insulation)	-	10	-
8(Core Identification)	-	20	-
9(Laying up of cores)	-	20	-
10.1.1(Sheathing )	-	20	-
10.2(Sheathing )	-	20	-
3 & 6(Flexibility class)	-	20	-
3 & 6(Construction)	-	20	-
3 & 6(Diameter of wire(mm))	-	20	-
3 & 6(Annealing test)	-	20	-
3 & 6(Persulphate Test)	-	20	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	20	-
7.2, 10.3, 11(Dimensions & thickness )	-	350	-
7.2, 10.3, 11(Dimensions & thickness )	-	0	-
7.2, 10.3, 11(Overall Dimension (mm))	-	0	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	250	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	250	-
4.2 & 12.1, (f), 1(Tensile Strength at break (N/mm²))	-	0	-
4.2 & 12.1, (e), 1(elongation test at break)	-	0	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	0	-
4.2 & 12.1, (f), 2(Ageing in air oven)	-	750	-
4.2 & 12.1, (f), 3(Ageing in oxygen bomb)	-	700	-
4.2 & 12.1, (e), 2(After Ageing in air oven)	-	0	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Insulation)	-	750	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Sheath)	-	0	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Insulation)	-	250	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Sheath)	-	250	-
4.2 & 12.1, (e), 5(Heat Shock Test of Insulation)	-	125	-
4.2 & 12.1, (e), 5(Heat Shock Test of Sheath)	-	125	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Insulation)	-	100	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Sheath)	-	100	-
14(High Voltage Test)	-	1500	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	1000	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	1000	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	1000	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	200	-
19.2(EFFECT OF OIL ON IGNITION CABLES)	-	200	-
20.3(EFFECT OF LUBRICATING OIL)	-	200	-
20.3(EFFECT OF BRAKE FLUID)	-	200	-
20.3(EFFECT OF DIESEL)	-	200	-
20.3(Increase in average diameter %)	-	0	-
20.3(Wrapping test)	-	0	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	1000	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
22.1(FLAMMABILITY TEST)	-	250	-
22.1(FLAMMABILITY TEST)	-	0	-
23.1(Manufacturer's Identification)	-	20	-
23.1(Manufacturer's Identification)	-	0	-
24.1(PACKING AND MARKING)	-	10	-
24.2.1(PACKING AND MARKING)	-	10	-
7.1(Insulation)	-	0	-
7.3(Insulation)	-	0	-
8(Core Identification)	-	0	-
9(Laying up of cores)	-	0	-
10.1.1(Sheathing )	-	0	-
10.2(Sheathing )	-	0	-
3 & 6(Flexibility class)	-	0	-
3 & 6(Construction)	-	0	-
3 & 6(Diameter of wire(mm))	-	0	-
3 & 6(Annealing test)	-	0	-
3 & 6(Persulphate Test)	-	0	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	0	-
7.2, 10.3, 11(Dimensions & thickness )	-	0	-
7.2, 10.3, 11(Dimensions & thickness )	-	0	-
7.2, 10.3, 11(Overall Dimension (mm))	-	0	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	0	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	0	-
4.2 & 12.1, (f), 1(Tensile Strength at break (N/mm²))	-	0	-
4.2 & 12.1, (e), 1(elongation test at break)	-	0	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	0	-
4.2 & 12.1, (f), 2(Ageing in air oven)	-	0	-
4.2 & 12.1, (f), 3(Ageing in oxygen bomb)	-	0	-
4.2 & 12.1, (e), 2(After Ageing in air oven)	-	0	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Insulation)	-	0	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Sheath)	-	0	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Insulation)	-	0	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Sheath)	-	0	-
4.2 & 12.1, (e), 5(Heat Shock Test of Insulation)	-	0	-
4.2 & 12.1, (e), 5(Heat Shock Test of Sheath)	-	0	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Insulation)	-	0	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Sheath)	-	0	-
14(High Voltage Test)	-	0	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	0	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	0	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	0	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	0	-
19.2(EFFECT OF OIL ON IGNITION CABLES)	-	0	-
20.3(EFFECT OF LUBRICATING OIL)	-	0	-
20.3(EFFECT OF BRAKE FLUID)	-	0	-
20.3(EFFECT OF DIESEL)	-	0	-
20.3(Increase in average diameter %)	-	0	-
20.3(Wrapping test)	-	0	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
22.1(FLAMMABILITY TEST)	-	0	-
22.1(FLAMMABILITY TEST)	-	0	-
23.1(Manufacturer's Identification)	-	0	-
23.1(Manufacturer's Identification)	-	0	-
24.1(PACKING AND MARKING)	-	0	-
24.2.1(PACKING AND MARKING)	-	0	-

-
Included w.e.f. 17.11.2023. Exclusion: Cl.15 (SPARK TEST FOR SINGLE CORE GENERAL WIRING CABLES)

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

10000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	100	-
7.1 Table-1(Dimensional measurement of wires)	-	1200	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	1300	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	100	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	150	-
9.1(Stranding)	-	100	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	350	-
9.3(Direction of Lay)	-	350	-
9.4(Multiple layers of wires)	-	0	-
11(Packing and Marking)	-	0	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	625	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	625	-
12.3 Table 1(Elongation Test- Before Stranding)	-	625	-
12.3 Table 1(Elongation Test- After Stranding)	-	625	-
12.4 Table 1(Resistance of Aluminium wire)	-	2000	-
9.2(Lay Ratio 24 wire layer)	-	700	-
9.2(Lay Ratio 18 wire layer)	-	175	-
9.2(Lay Ratio 12 wire layer)	-	700	-
9.2(Lay Ratio 3/6 wire layer)	-	175	-
6.1(Freedom from Defects)	-	0	-
7.1 Table-1(Dimensional measurement of wires)	-	0	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	0	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	-
9.1(Stranding)	-	0	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	0	-
9.3(Direction of Lay)	-	0	-
9.4(Multiple layers of wires)	-	0	-
11(Packing and Marking)	-	0	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	0	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	0	-
12.3 Table 1(Elongation Test- Before Stranding)	-	0	-
12.3 Table 1(Elongation Test- After Stranding)	-	0	-
12.4 Table 1(Resistance of Aluminium wire)	-	0	-
9.2(Lay Ratio 24 wire layer)	-	0	-
9.2(Lay Ratio 18 wire layer)	-	0	-
9.2(Lay Ratio 12 wire layer)	-	0	-
9.2(Lay Ratio 3/6 wire layer)	-	0	-

-
Included w.e.f. 17.11.2023

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

10000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	250	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	250	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	250	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	250	-
10 (elec)(Stranding)	-	100	-
10 (elec)(Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
10 (mech)(Stranding)	-	0	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	250	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	250	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	250	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	250	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	500	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	0	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	500	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	0	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	350	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	350	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	175	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	175	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	175	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	175	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	750	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	750	-
13.7.2 (chem)(Mass of Zinc coating)	-	700	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	700	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	75	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	75	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	75	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	75	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	75	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	75	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	75	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	75	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	700	-
13.7.2 (elec)(Mass of Zinc coating)	-	700	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	600	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	0	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	0	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	0	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	0	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	0	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	0	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	0	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	0	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	0	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	0	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	0	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	0	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	0	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	0	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	0	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	0	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
10 (mech)(Stranding)	-	0	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	0	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	0	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	0	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	0	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	0	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	0	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	0	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	0	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	0	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	0	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	0	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	0	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	0	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	0	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	0	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	0	-
13.7.2 (chem)(Mass of Zinc coating)	-	0	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	0	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	0	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	0	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	0	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	0	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	0	-
13.7.2 (elec)(Mass of Zinc coating)	-	0	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	0	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	0	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	0	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	0	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	0	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	0	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	0	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	0	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	0	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	0	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	0	-
10 (elec)(Stranding)	-	0	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	0	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	0	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	0	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	0	-

-
Included w.e.f. 17.11.2023. Restricted up to 100 sq. mm: [Cl.13.9 (Surface condition test), Cl. 13.10 (Ultimate breaking load), Cl. 13.11 (Stress-strain test)]

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

5625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	750	-
12.3, Table-1(Breaking load before stranding)	-	750	-
12.3, Table-1(Breaking load after stranding)	-	750	-
12.4(Wrapping test)	-	350	-
12.5, Table 1(Resistance test)	-	1000	-
12.6, Table 3(Measurement of lay ratio)	-	400	-
9.3(Stranding)	-	50	-
6(Freedom from defects)	-	50	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	0	-
12.3, Table-1(Breaking load before stranding)	-	0	-
12.3, Table-1(Breaking load after stranding)	-	0	-
12.4(Wrapping test)	-	0	-
12.5, Table 1(Resistance test)	-	0	-
12.6, Table 3(Measurement of lay ratio)	-	0	-
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-
12.3, Table-1(Breaking load after stranding)	-	750	-
12.4(Wrapping test)	-	700	-

-
Included w.e.f. 17.11.2023

IS 302 : Part 2 : Sec 3 (2007)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 3 electric iron (First Revision)

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.14(Marking- IS 302-1)	-	100	Testing charges
8( Protection Against Electric Shock, IS 302-1)	-	150	Testing charges
10(Power Input and Current, IS 302-1)	-	150	Testing charges
11(Heating, IS 302-1)	-	150	Testing charges
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	150	Testing charges
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	0	Testing charges
14(Transient Over Voltages, IS 302-1)	-	150	Testing charges
15.1(Moisture Resistance, IS 302-1)	-	75	Testing charges
15.3(Moisture Resistance, IS 302-1)	-	75	Testing charges
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	150	Testing charges
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	0	Testing charges
19.4(Abnormal Operation, IS 302-1)	-	50	Testing charges
19.5(Abnormal Operation, IS 302-1)	-	50	Testing charges
19.7(Abnormal Operation)	-	0	Testing charges
19.9(Abnormal Operation)	-	50	Testing charges
20.1(Stability & Mechanical Hazards, IS 302-1)	-	100	Testing charges
20.2(Stability & Mechanical Hazards, IS 302-1)	-	50	Testing charges
21.1(Mechanical Strength, IS 302-1)	-	50	Testing charges
21.2(Mechanical Strength, IS 302-1)	-	50	Testing charges
21.101(Mechanical Strength, IS 302-2-3)	-	50	Testing charges
22(Construction, IS 302-1)	-	75	Testing charges
22.104(Construction)	-	75	Testing charges
23.5(Internal Wiring, IS 302-1)	-	150	Testing charges
24.1(Components, IS 302-1)	-	100	Testing charges
24.6(Components, IS 302-1)	-	50	Testing charges
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	50	Testing charges
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	50	Testing charges
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	50	Testing charges
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	0	Testing charges
26(Terminals for External Conductors, IS 302-1)	-	150	Testing charges
27.2(Provision for Earthing, IS 302-1)	-	50	Testing charges
27.5(Provision for Earthing, IS 302-1)	-	100	Testing charges
28(Screws & Connections, IS 302-1)	-	150	Testing charges
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	75	Testing charges
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	75	Testing charges
30.1(Resistance to Heat, Fire & Tracking, IS 302-1)	-	150	Testing charges
30.2(Resistance to Heat, Fire & Tracking, IS 302-1)	-	150	Testing charges
31(Resistance of Rusting, IS 302-1)	-	150	Testing charges

-
Restricted to Dry Iron only.

IS 3854 (1997)

Switches for domestic and similar purposes - Specification (Second Revision)

10000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Marking)	-	20	-
8(Marking)	-	20	-
8(Marking)	-	20	-
8(Marking)	-	20	-
8(Marking)	-	20	-
8(Marking)	-	20	-
8(Marking)	-	20	-
8(Marking)	-	20	-
8(Marking)	-	20	-
8.9(Marking)	-	20	Test
8(Marking)	-	20	-
6(Rating)	-	20	-
6(Rating)	-	20	-
7(Classification)	-	20	-
7(Classification)	-	20	-
7(Classification)	-	20	-
7(Classification)	-	20	-
7(Classification)	-	20	-
7(Classification)	-	20	-
7(Classification)	-	20	-
7(Classification)	-	20	-
7(Classification)	-	20	-
10(Protection against Electric Shock)	-	20	Test
11.1(Provision for earthing)	-	20	Test
12(Terminals)	-	20	Test
12.2.1(Terminals)	-	20	-
12(Terminals)	-	20	-
12.2.2(Connection of conductor)	-	20	-
12.2.3(Mechanical strength of terminals)	-	20	-
12.2.3(Mechanical strength of terminals)	-	20	-
12.2.4(Resistance to corrosion)	-	20	-
12.2.4(Resistance to corrosion)	-	20	-
12.2.5(Undue damage to conductor)	-	50	Test
12.2.7(Insertion of conductor)	-	20	Test
12.2.9(Locking against accidental loosening)	-	20	Test
12.2.11(Distance between screw and conductor)	-	20	Test
12.2.11(Distance between screw and conductor)	-	20	-
12.3.2(Screwless terminals)	-	20	Test
12.3.3(Connectin of conductor)	-	20	-
12.3.4(Material of terminals)	-	20	-
12.3.5(Clamping)	-	20	Test
12.3.5(Clamping)	-	20	-
12.3.7(v) Interconnection of conductors [Cl. 12.3.7])	-	20	-
12.3.7(v) Interconnection of conductors [Cl. 12.3.7])	-	20	-
12.3.11(vi) Electrical & Thermal Stresses [Cl 12.3.11])	-	20	Test
12.3.11(vi) Electrical & Thermal Stresses [Cl 12.3.11])	-	20	-
12.3.12(vii) Deflection Stresses [Cl. 12.3.12])	-	20	Test
13.1(a) Insulating lining, barriers and the like [Cl 13.1])	-	20	-
13.2(b) Construction of switch [Cl 13.2])	-	20	-
13.2(i) Installation Test)	-	20	Test
13.3(c) Covers,cover plates and actuating members [Cl 13.3])	-	20	Test
13.4(d) Ordinary switches [Cl 13.4])	-	20	Test
13.5(e) Rotary switches [Cl 13.5])	-	20	Test
13.6(f) Screws and other means [Cl 13.6])	-	20	-
13.7(g) Combination of switches or switches and socket outlets [Cl 13.7])	-	20	-
13.8(h) Assessories combined with switches [Cl. 13.8])	-	20	-
13.9(j) Switches other than ordinary switches [Cl. 13.9])	-	20	Test
13.9(j) Switches other than ordinary switches [Cl. 13.9])	-	20	-
13.9(j) Switches other than ordinary switches [Cl. 13.9])	-	20	-
13.9(j) Switches other than ordinary switches [Cl. 13.9])	-	20	-
13.9(j) Switches other than ordinary switches [Cl. 13.9])	-	20	-
13.9(j) Switches other than ordinary switches [Cl. 13.9])	-	20	-
13.9(j) Switches other than ordinary switches [Cl. 13.9])	-	20	-
13.1(k) Switches to be installed in a box [Cl. 13.10])	-	20	-
13.11(l) Surface type switches other than ordinary switch [Cl. 13.11])	-	20	Test
13.12, 13.13, 13.14(m) Inlet opening [Cl. 13.12.13.13 & 13.14])	-	20	Test
13.15(q) Requirements for membrane in inlet opening [ Cl. 13.15])	-	20	Test
13.15(q) Requirements for membrane in inlet opening [ Cl. 13.15])	-	20	-
13.15(q) Requirements for membrane in inlet opening [ Cl. 13.15])	-	20	-
13.15(q) Requirements for membrane in inlet opening [ Cl. 13.15])	-	20	-
14(Mechanism [Cl. 14])	-	20	-
14.4(Mechanism)	-	20	Test
15.1(Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-	100	Test
15.2(b)Resistance to Harmful ingress of water [Cl. 15.2])	-	100	Test
15.2(b)Resistance to Harmful ingress of water [Cl. 15.2])	-	100	-
15.3(c) Resistance to Humidity [Cl. 15.3])	-	200	Test
16.1(Insulation resistance [Cl. 16.1])	-	200	Test
16.2( Electric Strength [Cl. 16.2])	-	200	Test
17(Temperature- rise [Cl. 17])	-	200	Test
18(Marking and breaking Capacity[Cl. 18])	-	250	-
18(Marking and breaking Capacity[Cl. 18])	-	250	Test
19(Normal Operation [Cl. 19] a) General & Operation)	-	500	-
19.2(Normal Operation (For AX type Switches) [Cl. 19.2])	-	500	-
19(b) Electric Strength)	-	200	-
19(c)Temperature-rise )	-	200	-
14.3(d)Test for arcing and sparking [Cl 14.3])	-	200	Test
19.2(Normal Operation (For AX type Switches) [Cl. 19.2])	-	200	Test
20(Mechanical Strength Test [Cl. 20])	-	20	Test
21(Resistance to Heat [Cl.21])	-	20	Test
21(Resistance to Heat [Cl.21])	-	20	-
21(Resistance to Heat [Cl.21])	-	20	-
22(Screw, Current Carrying Part And Connection [Cl.22])	-	20	-
22.1(i) Screw & Nuts [Cl.22.1])	-	20	Test
22.4(ii) Screw & rivets [Cl . 22.4])	-	20	-
22.3(iii) Electrical Connections [Cl.22.3])	-	20	-
22.5(iv) Current carrying part [Cl.22.5])	-	20	-
23.2(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	20	Test
23(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	20	-
23(Creepage distances, clearances and distance through sealing compound [Cl.23])	-	20	-
24.1.1(Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-	200	Test
24.2(Resistance to tracking [For Switch other than ordinary] [Cl.24.2])	-	200	Test
24.2(Resistance to tracking [For Switch other than ordinary] [Cl.24.2])	-	200	-
25 of IS 3854 : 1997(Resistance to rusting)	-	200	-
11.3(Provision for earthing)	-	20	-
11.2(Provision for earthing)	-	20	-
12.3.9(Screwless terminal fixing)	-	20	-
12.3.8(Screwless terminals design)	-	20	-
12.3.6(Connection)	-	20	-
12.3.1(Screwless terminals)	-	20	-
14.6(Mechanism)	-	20	-
14.5(Mechanism)	-	20	-
16.3(Flash test)	-	20	-
20.8(Mechanical Strength Test)	-	20	-
20.7(Mechanical Strength Test)	-	20	-
20.6(Mechanical Strength Test)	-	20	-
20.5(Mechanical Strength Test)	-	20	-
20.4(Mechanical Strength Test)	-	20	-
20.3(Mechanical Strength Test)	-	20	-
20.2(Mechanical Strength Test)	-	20	-
20.1(Mechanical Strength Test)	-	20	-
21.2(Resistance to Heat)	-	20	-
21.1(Resistance to Heat)	-	20	-
22.2(Measurement and manual test)	-	20	-
22.6(Inspection and chemical analysis)	-	20	-
24.1(Resistance of insulating material to abnormal heat, to fire and to tracking )	-	200	-
24(Resistance of insulating material to abnormal heat, to fire and to tracking )	-	200	-
23.2(Creepage distances, clearances & distance through sealing compound )	-	20	-
23.1(Creepage distances, clearances & distance through sealing compound )	-	20	-
22.7(Screws, current carrying parts and connections )	-	20	-
22.6(Screws, current carrying parts and connections )	-	20	-
22.5(Screws, current carrying parts and connections )	-	20	-
22.4(Screws, current carrying parts and connections )	-	20	-
22.3(Screws, current carrying parts and connections )	-	20	-
22.2(Screws, current carrying parts and connections )	-	20	-
22.1(Screws, current carrying parts and connections )	-	20	-
21.3(Resistance to heat )	-	40	-
21.2(Resistance to heat )	-	20	-
21.1(Resistance to heat )	-	20	-
20.9(Mechanical strength )	-	20	-
20.8(Mechanical strength )	-	10	-
20.7(Mechanical strength )	-	10	-
20.6 & 24.4.2(Mechanical strength )	-	20	-
20.6 & 24.4.1(Mechanical strength )	-	20	-
20.5 & 24.4.2(Mechanical strength )	-	20	-
20.5 & 24.4.1(Mechanical strength )	-	20	-
20.4.2(Mechanical strength )	-	20	-
20.4.1(Mechanical strength )	-	20	-
20.4(Mechanical strength )	-	20	-
20.3(Mechanical strength )	-	20	-
20.2(Mechanical strength )	-	20	-
20.1(Mechanical strength )	-	20	-
19.2(Normal operation)	-	20	-
19.1(Normal operation)	-	500	-
18.2(Making and breaking capacity )	-	200	-
18.1(Making and breaking capacity )	-	200	-
16.3(Insulation resistance and electric strength )	-	100	-
16(Insulation resistance and electric strength )	-	100	-
15.3(Resistance to ageing, to harmful ingress of water and to humidity )	-	100	-
15.2.3(Resistance to ageing, to harmful ingress of water and to humidity )	-	100	-
15.2.2(Resistance to ageing, to harmful ingress of water and to humidity )	-	100	-
15.2.1(Resistance to ageing, to harmful ingress of water and to humidity )	-	100	-
15.2(Resistance to ageing, to harmful ingress of water and to humidity )	-	100	-
15.1(Resistance to ageing, to harmful ingress of water and to humidity )	-	100	-
15(Resistance to ageing, to harmful ingress of water and to humidity )	-	100	-
14.6(Mechanism)	-	10	-
14.5(Mechanism)	-	10	-
14.4(Mechanism)	-	10	-
14.3(Mechanism)	-	10	-
14.2(Mechanism)	-	10	-
14.1(Mechanism)	-	20	-
13.15.2(Constructional requirements )	-	20	-
13.15.1(Constructional requirements )	-	20	-
13.15(Constructional requirements )	-	20	-
13.14(Constructional requirements )	-	20	-
13.13(Constructional requirements )	-	20	-
13.12(Constructional requirements )	-	20	-
13.11(Constructional requirements )	-	20	-
13.1(Constructional requirements )	-	20	-
13.9(Constructional requirements )	-	20	-
13.8(Constructional requirements )	-	20	-
13.7(Constructional requirements )	-	20	-
13.6(Constructional requirements )	-	20	-
13.5(Constructional requirements )	-	20	-
13.4(Constructional requirements )	-	20	-
13.3.3(Constructional requirements )	-	20	-
13.3.2(Constructional requirements )	-	20	-
13.3.1(Constructional requirements )	-	20	-
13.3(Constructional requirements )	-	20	-
13.2(Constructional requirements )	-	20	-
13.1(Constructional requirements )	-	20	-
13(Constructional requirements )	-	20	-
12.3.12(Terminals)	-	20	-
12.3.11.b(Terminals)	-	20	-
12.3.11.a(Terminals)	-	20	-
12.3.10(Terminals)	-	20	-
12.3.9(Terminals)	-	20	-
12.3.8(Terminals)	-	20	-
12.3.6(Terminals)	-	20	-
12.2.6(Terminals)	-	20	-
12.2(Terminals)	-	20	-
12.1(Terminals)	-	20	-
11.4(Provision for earthing)	-	20	-
11.3(Provision for earthing)	-	20	-
11.2(Provision for earthing)	-	20	-
11.1(Provision for earthing)	-	20	-
10.7(Protection against electric shock )	-	20	-
10.6(Protection against electric shock )	-	20	-
10.5(Protection against electric shock )	-	20	-
10.4(Protection against electric shock )	-	20	-
10.3.2(Protection against electric shock )	-	20	-
10.3.1(Protection against electric shock )	-	20	-
10.3(Protection against electric shock )	-	20	-
10.2(Protection against electric shock )	-	20	-
10.1(Protection against electric shock )	-	20	-
8.1(Marking)	-	20	-
8.8(Marking)	-	20	-
8.7(Marking)	-	20	-
8.6(Marking)	-	20	-
8.5(Marking)	-	20	-
8.4(Marking)	-	20	-
8.3(Marking)	-	20	-
8.2(Marking)	-	20	-
8.1(Marking)	-	20	-
7.2(Classification)	-	20	-
7.1.8(Classification)	-	20	-
7.1.7(Classification)	-	20	-
7.1.6(Classification)	-	20	-
7.1.5(Classification)	-	20	-
7.1.4(Classification)	-	20	-
7.1.3(Classification)	-	20	-
7.1.2(Classification)	-	20	-
7.1.1(Classification)	-	20	-
7.1(Classification)	-	20	-
6.2(Ratings)	-	20	-
6.1(Ratings)	-	20	-
6(Ratings)	-	20	-
25(Resistance to Rusting)	-	200	-

-
Included w.e.f. 11.10.2018

IS 1293 (2005)

Plugs and socket- outlets of rated voltage up to and including 250 volts and rated current up to 16 amperes

250 Volts and rated current up to and including 16 A

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
29.0(Resistance to Rusting)	-	100	-
28.2(Resistance to Tracking)	-	100	-
28.1.1(Glow-Wire Test )	-	100	-
27.3(Creepage distances, clearances and distances through sealing compound )	-	20	-
27.2(Creepage distances, clearances and distances through sealing compound )	-	20	-
27.1(Creepage distances, clearances and distances through sealing compound )	-	20	-
26.7(Screws, current carrying parts and connections)	-	20	-
26.2(Screws, current carrying parts and connections)	-	20	-
26.1(Screws, current carrying parts and connections)	-	20	-
25.4(Resistance to heat)	-	100	-
25.3(Resistance to heat)	-	100	-
25.2(Resistance to heat)	-	100	-
25.1(Resistance to heat)	-	100	-
25.1(Resistance to heat)	-	100	-
24.14.2(f)Verification of the Removal of Covers or Cover-Plates )	-	20	-
24.14.1(e)Verification of the Non-removal of Covers or Cover-Plates )	-	20	-
24.8(c) For shuttered socket-outlets )	-	20	-
24.6(b) For screwed glands of accessories other than ordinary)	-	20	-
24.3(a) For surface type socket outlet)	-	20	-
24.1(a) Mechanical Strength )	-	20	-
22.2(Verification of Minimum withdrawal force)	-	20	-
22.1(Verification of Max withdrawal force)	-	20	-
21.0(Normal Operation)	-	300	-
21.0(Normal Operation)	-	300	-
21.0(Normal Operation)	-	300	-
21.0(Normal Operation)	-	300	-
20.0(Making & Breaking Capacity)	-	300	-
19.0(Temperature Rise )	-	100	-
18.0(Operation of Earthing Contacts)	-	20	-
17.2( Electric Strength)	-	100	-
17.1(Insulation Resistance)	-	100	-
16.3(Resistance to humidity)	-	100	-
16.2(Resistance to Harmful Ingress of Water)	-	20	-
16.1(Resistance to Ageing )	-	100	-
15.0(Interlocked socket-outlets)	-	20	-
13.17(Construction of fixed Socket Outlets)	-	20	-
13.14(Construction of fixed Socket Outlets)	-	20	-
13.16(Construction of fixed Socket Outlets)	-	20	-
13.1(Construction of fixed Socket Outlets)	-	20	-
13.9(Construction of fixed Socket Outlets)	-	20	-
13.5(Construction of fixed Socket Outlets)	-	20	-
13.4(Construction of fixed Socket Outlets)	-	20	-
13.4(Construction of fixed Socket Outlets)	-	20	-
13.4(Construction of fixed Socket Outlets)	-	20	-
13.4(Construction of fixed Socket Outlets)	-	20	-
13.4(Construction of fixed Socket Outlets)	-	20	-
13.3(Construction of fixed Socket Outlets)	-	20	-
13.2(Construction of fixed Socket Outlets)	-	20	-
13.1(Construction of fixed Socket Outlets)	-	20	-
12.2.11(Terminals)	-	20	-
12.2.10(Terminals)	-	20	-
12.2.9(Terminals)	-	20	-
12.2.7(Terminals)	-	20	-
12.2.5(Terminals)	-	20	-
12.2.4(Terminals)	-	20	-
12.2.3(Terminals)	-	20	-
12.2.2(Terminals)	-	20	-
12.2.1(Terminals)	-	20	-
11.5(Provision for Earthing)	-	20	-
11.2(Provision for Earthing)	-	20	-
11.1(Provision for Earthing)	-	20	-
10.6(Protection against Electric Shock)	-	20	-
10.5(Protection against Electric Shock)	-	20	-
10.3(Protection against Electric Shock)	-	20	-
10.1(Protection against Electric Shock)	-	20	-
10.1(Protection against Electric Shock)	-	20	-
9.0(16 A)	-	20	-
9.0(16 A)	-	20	-
9.0(16 A)	-	20	-
9.0(6A/10A )	-	20	-
9.0(6A/10A )	-	20	-
9.0(6A/10A )	-	20	-
9.0(Checking of dimensions)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
8.0(Marking)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
7.0(Classification)	-	20	-
6.0(Ratings)	-	20	-
6.0(Ratings)	-	20	-
30.4(Addiitional tests on pins provided with insulating sleeves - Tests at Low Temperature)	-	100	-
30.3(Addiitional tests on pins provided with insulating sleeves - Impact Test at Low Temperature)	-	100	-
30.2(Addiitional tests on pins provided with insulating sleeves - Static Damp Heat Test)	-	100	-
30.1(Addiitional tests on pins provided with insulating sleeves - Pressure Test at High Temperature)	-	100	-
30.4(Addiitional tests on pins provided with insulating sleeves - Tests at Low Temperature)	-	100	-
30.3(Addiitional tests on pins provided with insulating sleeves - Impact Test at Low Temperature)	-	100	-
30.2(Addiitional tests on pins provided with insulating sleeves - Static Damp Heat Test)	-	100	-
30.1(Addiitional tests on pins provided with insulating sleeves - Pressure Test at High Temperature)	-	100	-
28.1.2(Addiitional tests for plugs with pins provided with insulating sleeves)	-	100	-
24.18(Verification of the Removal of Covers or Cover-Plates )	-	20	-
24.17(Verification of the Removal of Covers or Cover-Plates )	-	20	-
24.16(Verification of the Removal of Covers or Cover-Plates )	-	20	-
24.15(Verification of the Removal of Covers or Cover-Plates )	-	20	-
24.13(For portable socket outlets having means for suspension on a wall)	-	20	-
24.12(For portable socket outlets having means for suspension on a wall)	-	20	-
24.11(For portable socket outlets having means for suspension on a wall)	-	20	-
24.1(For plugs)	-	20	-
24.9(For portable multiple and combined socket outlets)	-	20	-
24.7(For plug pins provided with insulating sleeves)	-	20	-
24.5(For Portable single socket outlets/ plugs)	-	20	-
24.4(For Portable socket outlets/ plugs)	-	20	-
24.2(For Portable single socket outlets/ plugs)	-	20	-
23.4(Flexible cables & their connection )	-	20	-
23.3(Flexible cables & their connection )	-	20	-
23.2(Flexible cables & their connection )	-	20	-
23.1(Flexible cables & their connection )	-	20	-
14.15(Construction of Plugs & Portables socket outlet )	-	20	-
14.11(Construction of Plugs & Portables socket outlet )	-	20	-
14.1(Construction of Plugs & Portables socket outlet )	-	20	-
14.9(Construction of Plugs & Portables socket outlet )	-	20	-
14.9(Construction of Plugs & Portables socket outlet )	-	20	-
14.8(Construction of Plugs & Portables socket outlet )	-	20	-
14.7(Construction of Plugs & Portables socket outlet )	-	20	-
14.3(Construction of Plugs & Portables socket outlet )	-	20	-
14.2(Construction of Plugs & Portables socket outlet )	-	20	-
14.1(Construction of Plugs & Portables socket outlet )	-	20	-
12.1(Terminals)	-	20	-
10.4(Protection against Electric Shock)	-	20	-
10.1(Protection against Electric Shock)	-	20	-
10.1(Protection against Electric Shock)	-	20	-
9(16 A)	-	20	-
9(16 A)	-	20	-
9(16 A)	-	20	-
9(6A/10A )	-	20	-
9(16 A)	-	20	-
9(6A/10A )	-	20	-
9(6A/10A )	-	20	-
9(6A/10A )	-	20	-
9(6A/10A )	-	20	-
8(Marking)	-	20	-
28.1.2(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	100	-
28.1(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	100	-
27(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	20	-
26.6(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.5(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.4(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.3(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
25(RESISTANCE TO HEAT)	-	20	-
24.18(MECHANICAL STRENGTH)	-	20	-
24.17(MECHANICAL STRENGTH)	-	20	-
24.16 & 24.14.2(MECHANICAL STRENGTH)	-	20	-
24.16 & 24.14.1(MECHANICAL STRENGTH)	-	20	-
24.15 & 24.14.2(MECHANICAL STRENGTH)	-	20	-
24.15 & 24.14.1(MECHANICAL STRENGTH)	-	20	-
24.14.2(MECHANICAL STRENGTH)	-	20	-
24.14.1(MECHANICAL STRENGTH)	-	20	-
24.14(MECHANICAL STRENGTH)	-	20	-
24.13(MECHANICAL STRENGTH)	-	20	-
24.12(MECHANICAL STRENGTH)	-	20	-
24.11(MECHANICAL STRENGTH)	-	20	-
24.1(MECHANICAL STRENGTH)	-	20	-
24.9(MECHANICAL STRENGTH)	-	20	-
24.8(MECHANICAL STRENGTH)	-	20	-
24.7(MECHANICAL STRENGTH)	-	20	-
24.6(MECHANICAL STRENGTH)	-	20	-
24.5(MECHANICAL STRENGTH)	-	20	-
24.4(MECHANICAL STRENGTH)	-	20	-
24.3(MECHANICAL STRENGTH)	-	20	-
24.2(MECHANICAL STRENGTH)	-	20	-
24.1(MECHANICAL STRENGTH)	-	20	-
24(MECHANICAL STRENGTH)	-	20	-
23.4(FLEXIBLE CABLES AND THEIR CONNECTION)	-	20	-
23.3(FLEXIBLE CABLES AND THEIR CONNECTION)	-	20	-
23.2(FLEXIBLE CABLES AND THEIR CONNECTION)	-	20	-
23.1(FLEXIBLE CABLES AND THEIR CONNECTION)	-	20	-
23(FLEXIBLE CABLES AND THEIR CONNECTION)	-	20	-
22(FORCE NECESSARY TO WITHDRAW THE PLUG)	-	20	-
17.3(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	100	-
17.1.2(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	100	-
17.1.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	100	-
17(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	100	-
16.2.4(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
16.2.3(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
16.2.2(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
16.2.1(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
16(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
14.25(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.24(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.23.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.23.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.23(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.22(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.21(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.19(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.18(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.17(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.16(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.15(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.13(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.12(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.11(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.9(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.8(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.7(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.6(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.5(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.4(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
13.23(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.22(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.21(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.2(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.19(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.18(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.15(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.13(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.12(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.11(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.8(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.7.3 (CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.7.2 (CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.7.1(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13.7(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
13(CONSTRUCTION OF FIXED SOCKETOUTLETS)	-	20	-
12.3.12 (TERMINALS)	-	20	-
12.3.11 (b)(TERMINALS)	-	20	-
12.3.11 (a)(TERMINALS)	-	20	-
12.3.10(TERMINALS)	-	20	-
12.3.9(TERMINALS)	-	20	-
12.3.8(TERMINALS)	-	20	-
12.3.7(TERMINALS)	-	20	-
12.3.6(TERMINALS)	-	20	-
12.3.5(TERMINALS)	-	20	-
12.3.4(TERMINALS)	-	20	-
12.3.3(TERMINALS)	-	20	-
12.3.2(TERMINALS)	-	20	-
12.3.1(TERMINALS)	-	20	-
12.3(TERMINALS)	-	20	-
12.2.8(TERMINALS)	-	20	-
12.2.6(TERMINALS)	-	20	-
12.2(TERMINALS)	-	20	-
12.1.2(TERMINALS)	-	20	-
12.1.1(TERMINALS)	-	20	-
12(TERMINALS)	-	20	-
11.4(PROVISION FOR EARTHING)	-	20	-
11.3(PROVISION FOR EARTHING)	-	20	-
11(PROVISION FOR EARTHING)	-	20	-
10.7(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.4(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.2.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.2.1(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
9.3(CHECKING OF DIMENSIONS)	-	100	-
9.2(CHECKING OF DIMENSIONS)	-	100	-
9.1(CHECKING OF DIMENSIONS)	-	100	-
8.8(MARKING)	-	20	-
8.7(MARKING)	-	20	-
8.6(MARKING)	-	20	-
8.5(MARKING)	-	20	-
8.4(MARKING)	-	20	-
8.3(MARKING)	-	20	-
8.2(MARKING)	-	20	-
8.1(MARKING)	-	20	-
7.3(CLASSIFICATION)	-	20	-
7.2.5(CLASSIFICATION)	-	20	-
7.2.4(CLASSIFICATION)	-	20	-
7.2.3(CLASSIFICATION)	-	20	-
7.2.2 (CLASSIFICATION)	-	20	-
7.2.1(CLASSIFICATION)	-	20	-
7.2(CLASSIFICATION)	-	20	-
7.1.4(CLASSIFICATION)	-	20	-
7.1.3 (CLASSIFICATION)	-	20	-
7.1.2(CLASSIFICATION)	-	20	-
7.1.1 (CLASSIFICATION)	-	20	-
7.1(CLASSIFICATION)	-	20	-
6.2(RATINGS)	-	20	-
6.1(RATINGS)	-	20	-
30(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES)	-	100	-
29(RESISTANCE TO RUSTING)	-	100	-
28.2(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	100	-
28.1.1(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	100	-
28.1(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	100	-
28(RESISTANCE OF INSULATING MATERIAL TO ABNORMAL HEAT, TO FIRE AND TO TRACKING)	-	100	-
27.3(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	100	-
27.2(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	100	-
27.1(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	20	-
27(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	20	-
26.7(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.6(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.5(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.4(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.3(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.2(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26.1(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
26(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	20	-
25.4(RESISTANCE TO HEAT)	-	20	-
25.3(RESISTANCE TO HEAT)	-	20	-
25.2(RESISTANCE TO HEAT)	-	20	-
25.1(RESISTANCE TO HEAT)	-	20	-
25(RESISTANCE TO HEAT)	-	20	-
24.16 & 24.14.2(MECHANICAL STRENGTH)	-	20	-
24.16 & 24.14.1(MECHANICAL STRENGTH)	-	20	-
24.15 & 24.14.1(MECHANICAL STRENGTH)	-	20	-
24.14.2(MECHANICAL STRENGTH)	-	20	-
24.14.1(MECHANICAL STRENGTH)	-	20	-
24.14(MECHANICAL STRENGTH)	-	20	-
24.8(MECHANICAL STRENGTH)	-	20	-
24.6(MECHANICAL STRENGTH)	-	20	-
24.3(MECHANICAL STRENGTH)	-	20	-
24.1(MECHANICAL STRENGTH)	-	20	-
24(MECHANICAL STRENGTH)	-	20	-
23(FLEXIBLE CABLES AND THEIR CONNECTION)	-	20	-
21(NORMAL OPERATION)	-	300	-
20(MAKING AND BREAKING CAPACITY)	-	300	-
19(TEMPERATURE RISE)	-	100	-
18(OPERATION OF EARTHING CONTACTS)	-	100	-
17.3(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	100	-
17.1.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	100	-
17(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	100	-
16.3(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
16.2.4(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
16.2.3(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
16.2.2(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	100	-
16(RESISTANCE TO AGEING, TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	20	-
14.25(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.24(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.23.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.23.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.22(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.21(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.19(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.18(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.17(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.16(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.13(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.12(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.6(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.5(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
14.4(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	20	-
12.3.12 (TERMINALS)	-	20	-
12.3.11 (b)(TERMINALS)	-	20	-
12.3.11 (a)(TERMINALS)	-	20	-
12.3.10(TERMINALS)	-	20	-
12.3.9(TERMINALS)	-	20	-
12.3.8(TERMINALS)	-	20	-
12.3.7(TERMINALS)	-	20	-
12.3.6(TERMINALS)	-	20	-
12.3.5(TERMINALS)	-	20	-
12.3.4(TERMINALS)	-	20	-
12.3.3(TERMINALS)	-	20	-
12.3.2(TERMINALS)	-	20	-
12.3.1(TERMINALS)	-	20	-
12.3(TERMINALS)	-	20	-
12.2.11(TERMINALS)	-	20	-
12.2.10(TERMINALS)	-	20	-
12.2.9(TERMINALS)	-	20	-
12.2.8(TERMINALS)	-	20	-
12.2.7(TERMINALS)	-	20	-
12.2.6(TERMINALS)	-	20	-
12.2.5(TERMINALS)	-	20	-
12.2.4(TERMINALS)	-	20	-
12.2.3(TERMINALS)	-	20	-
12.2.2(TERMINALS)	-	20	-
12.2.1(TERMINALS)	-	20	-
12.2(TERMINALS)	-	20	-
12.1.2(TERMINALS)	-	20	-
12(TERMINALS)	-	20	-
11.5(PROVISION FOR EARTHING)	-	20	-
11.4(PROVISION FOR EARTHING)	-	20	-
11.3(PROVISION FOR EARTHING)	-	20	-
11.2(PROVISION FOR EARTHING)	-	20	-
11.1(PROVISION FOR EARTHING)	-	20	-
11(PROVISION FOR EARTHING)	-	20	-
10.7(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.6(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.5(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.3(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.2.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.2.1(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10.2(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
10(PROTECTION AGAINST ELECTRIC SHOCK)	-	20	-
9.3(CHECKING OF DIMENSIONS)	-	100	-
9.2(CHECKING OF DIMENSIONS)	-	100	-
9.1(CHECKING OF DIMENSIONS)	-	100	-
8.8(MARKING)	-	20	-
8.7(MARKING)	-	20	-
8.6(MARKING)	-	20	-
8.5(MARKING)	-	20	-
8.4(MARKING)	-	20	-
8.3(MARKING)	-	20	-
8.2(MARKING)	-	20	-
8.1(MARKING)	-	20	-
7.3(CLASSIFICATION)	-	20	-
7.2.5(CLASSIFICATION)	-	20	-
7.2.4(CLASSIFICATION)	-	20	-
7.2.3(CLASSIFICATION)	-	20	-
7.2.2 (CLASSIFICATION)	-	20	-
7.2.1(CLASSIFICATION)	-	20	-
7.2(CLASSIFICATION)	-	20	-
7.1.4(CLASSIFICATION)	-	20	-
7.1.3 (CLASSIFICATION)	-	20	-
7.1(CLASSIFICATION)	-	20	-
7(CLASSIFICATION)	-	20	-
6.2(RATINGS)	-	20	-
6.1(RATINGS)	-	20	-
6(RATINGS)	-	20	-

-
-

IS 366 (1991)

Electric iron - Specification (Fourth Revision)

9800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Classification (as per Cl.6 of IS 302-2-3 and Cl.6.1 of IS 302-1))	-	25	Testing charges
7.0(Classification (as per Cl.6 of IS 302-2-3 and Cl.6.2 of IS 302-1))	-	25	Testing charges
9.0(Protection against access to live parts (as per Cl. 8 of IS 302-2-3 and IS 302-1))	-	50	Testing charges
9.0(Power input and current (as per Cl. 10 of IS 302-2-3 and IS 302-1))	-	250	Testing charges
9.0(Temperature Rise (as per Cl. 11 of IS 302-2-3 and IS 302-1))	-	100	Testing charges
9.0(Temperature Rise (as per Cl. 11 of IS 302-2-3 and IS 302-1))	-	100	Testing charges
9.0(Temperature Rise (as per Cl. 11 of IS 302-2-3 and IS 302-1))	-	100	Testing charges
9.0(Temperature Rise (as per Cl. 11 of IS 302-2-3 and IS 302-1))	-	100	Testing charges
9.0(Leakage current and Electric Strength at Operating Temperature (as per Cl. 13 of IS 302-2-3 and IS 302-1))	-	200	Testing charges
9.0(Leakage current and Electric Strength at Operating Temperature (as per Cl. 13 of IS 302-2-3 and IS 302-1))	-	100	Testing charges
9.0(Transient Overvoltage (as per of Cl. 14 of IS 302-2-3 and Table 6 of IS 302-1))	-	250	Testing charges
9.0(Moisture Resistance (as per of Cl.15 of IS 302-2-3 and IS 302-1))	-	200	Testing charges
9.0(Moisture Resistance (as per of Cl.15 of IS 302-2-3 and IS 302-1))	-	200	Testing charges
9.0(Abnormal Operation (as per of Cl.19 of IS 302-2-3 and IS 302-1) )	-	250	Testing charges
9.0(Abnormal Operation (as per of Cl.19 of IS 302-2-3 and IS 302-1) )	-	250	Testing charges
9.0(Abnormal Operation (as per of Cl.19 of IS 302-2-3 and IS 302-1) )	-	100	Testing charges
9.0(Abnormal Operation (as per of Cl.19 of IS 302-2-3 and IS 302-1) )	-	100	Testing charges
9.0(Staibilty and mechanical hazards (as per of Cl.20 of IS 302-2-3 and IS 302-1) )	-	150	Testing charges
9.0(Mechanical strength (as per of Cl.21 of IS 302-2-3 and IS 302-1) )	-	200	Testing charges
9.0(Construction (as per of Cl.22 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Construction (as per of Cl.22 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Construction (as per of Cl.22 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Construction (as per of Cl.22 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Construction (as per of Cl.22 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Construction (as per of Cl.22 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Construction (as per of Cl.22 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Internal wiring (as per of Cl.23 of IS 302-2-3 and IS 302-1) )	-	150	Testing charges
9.0(Internal wiring (as per of Cl.23 of IS 302-2-3 and IS 302-1) )	-	150	Testing charges
9.0(Internal wiring (as per of Cl.23 of IS 302-2-3 and IS 302-1) )	-	100	Testing charges
9.0(Internal wiring (as per of Cl.23 of IS 302-2-3 and IS 302-1) )	-	100	Testing charges
9.0(Components (as per of Cl.24 of IS 302-2-3 and IS 302-1) )	-	250	Testing charges
9.0(Supply connection and external flexible cord (as per of Cl.25 of IS 302-2-3 and IS 302-1) )	-	150	Testing charges
9.0(Supply connection and external flexible cord (as per of Cl.25 of IS 302-2-3 and IS 302-1) )	-	150	Testing charges
9.0(Supply connection and external flexible cord (as per of Cl.25 of IS 302-2-3 and IS 302-1) )	-	150	Testing charges
9.0(Supply connection and external flexible cord (as per of Cl.25 of IS 302-2-3 and IS 302-1) )	-	100	Testing charges
9.0(Supply connection and external flexible cord (as per of Cl.25 of IS 302-2-3 and IS 302-1) )	-	100	Testing charges
9.0(Terminals for external conductors (as per of Cl.26 of IS 302-2-3 and IS 302-1) )	-	200	Testing charges
9.0(Provision for earthing (as per of Cl.27 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Provision for earthing (as per of Cl.27 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Provision for earthing (as per of Cl.27 of IS 302-2-3 and IS 302-1) )	-	50	Testing charges
9.0(Provision for earthing (as per of Cl.27 of IS 302-2-3 and IS 302-1) )	-	200	Testing charges
9.0(Screw and connections (as per of Cl.28 of IS 302-2-3 and IS 302-1))	-	150	Testing charges
9.0(Screw and connections (as per of Cl.28 of IS 302-2-3 and IS 302-1))	-	150	Testing charges
9.0(Clearances, creepage distances and solid insulation (as per of Cl.29 of IS 302-2-3 and IS 302-1))	-	200	Testing charges
9.0(Clearances, creepage distances and solid insulation (as per of Cl.29 of IS 302-2-3 and IS 302-1))	-	150	Testing charges
9.0(Resistance to Heat and Fire (as per of Cl.30 of IS 302-2-3 and IS 302-1))	-	250	Testing charges
9.0(Resistance to Rusting (as per of Cl.31 of IS 302-2-3 and IS 302-1))	-	250	Testing charges
10.0(Measurement of Heating up time)	-	150	Testing charges
10.0(Measurement of Heating up time)	-	150	Testing charges
11.0(Measurement of sole plate temperature)	-	100	Testing charges
11.0(Measurement of sole plate temperature)	-	100	Testing charges
11.0(Measurement of sole plate temperature)	-	100	Testing charges
11.0(Measurement of sole plate temperature)	-	100	Testing charges
13.0(Measurement of Initial overswing temperature and Heating up excess temperature)	-	750	Testing charges
13.0(Measurement of Initial overswing temperature and Heating up excess temperature)	-	400	Testing charges
14.0(Measurement of Cyclic fluctuation of temperature of hottest point )	-	500	Testing charges
16.0(Measurement of Thermostatic staibility)	-	250	Testing charges
16.0(Measurement of Thermostatic staibility)	-	250	Testing charges
16.0(Measurement of Thermostatic staibility)	-	350	Testing charges
16.0(Measurement of Thermostatic staibility)	-	150	Testing charges
16.0(Measurement of Thermostatic staibility)	-	150	Testing charges
16.0(Measurement of Thermostatic staibility)	-	150	Testing charges

-
Restricted to dry iron only

IS 8978 (1992)

Specification for electric instantaneous water heaters (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7 of IS 302-2-35:2017(Marking)	-	100	Test
Cl.8 of IS 302-2-35:2017(Protection Against Access To Live Parts)	-	350	Test
Cl.10 of IS 302-2- 35:2011(Power Input & Current )	-	500	Test
Cl.11 of 302-2-35:2017(Heating)	-	650	Test
Cl.13 of IS 302-2-35:2017(Leakage Current & Electrical Strength at Operating Temperature )	-	700	Test
Cl.14 of IS 302-2-35:2017(Transient Over Voltages )	-	700	Test
Cl.15 of IS 302-2-35-2011(Moisture Resistance )	-	700	Test
Cl.16 of IS 302-2-35:2011(Leakage Current and Electric Strength)	-	700	Test
Cl.17 IS 302-2-35:2017(Overload Protection of Transformers & Associated circuits )	-	350	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	700	Test
Cl.20 of IS 302-2-35-2011(Stability & Mechanical Hazards )	-	500	Test
Cl.21.1 of IS 302-2-35-2011(Mechanical strength)	-	500	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	400	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	500	Test
Cl.24 of IS 302-2-35:2017(Component )	-	400	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	300	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	500	Test
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	700	Test
Cl.28 of IS 302-2-35:2017(Screws and Connections )	-	300	Test
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	400	Test
Cl.30 of IS 302-2-35: 2011(Resistance to Heat and Fire)	-	600	Test
Cl.31 of IS 302-2-35: 2011(Resistance to Rusting )	-	400	Test
Cl.11 of IS 8978 : 1992(Operation of flow switch)	-	600	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.7 of IS 302-2-35:2017(Marking)	-	0	Test
Cl.6 of IS 302-2-35:2017(Classification)	-	0	Test
Cl.6 of IS 302-2-35:2017(Classification)	-	0	Test
Cl.11 of 302-2-35:2017(Heating)	-	0	Test
Cl.11 of 302-2-35:2017(Heating)	-	0	Test
Cl.11 of 302-2-35:2017(Heating)	-	0	Test
Cl.13 of IS 302-2-35:2017(Leakage Current & Electrical Strength at Operating Temperature )	-	0	Test
Cl.15 of IS 302-2-35-2011(Moisture Resistance )	-	0	Test
Cl.16 of IS 302-2-35:2011(Leakage Current and Electric Strength)	-	0	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	0	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	0	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	0	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation)	-	0	Test
Cl. 21.2 of IS 302-1:2008(Mechanical strength)	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.22 of IS 302-2-35-2011(Construction )	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.23 of IS 302-2-35-2011(Internal Wiring)	-	0	Test
Cl.24 of IS 302-2-35:2017(Component )	-	0	Test
Cl.24 of IS 302-2-35:2017(Component )	-	0	Test
Cl.24 of IS 302-2-35:2017(Component )	-	0	Test
Cl.24 of IS 302-2-35:2017(Component )	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	10	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	0	Test
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	0	Test
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	0	Test
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	0	Test
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	0	Test
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	0	Test
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	0	Test
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	0	Test
Cl.29 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation)	-	0	Test
Cl.30 of IS 302-2-35: 2011(Resistance to Heat and Fire)	-	0	Test
Cl.32 of IS 302-2-35: 2011(Radiation, Toxicity and Similar Hazards )	-	40	Test
Cl.10 of IS 8978 : 1992(Finish)	-	10	Test
Cl.12 of IS 8978 : 1992(Endurance)	-	500	Test
Cl.12 of IS 8978 : 1992(Endurance)	-	10	Test
Cl.10 of IS 8978 : 1992(Finish)	-	10	Test
Cl.31 of IS 302-2-35: 2017(Resistance to Rusting )	-	10	Test
Cl.30.2 of IS 302-1:2008(Resistance to Heat and Fire)	-	10	Test
Cl.30.1 of IS 302-1:2008(Resistance to Heat and Fire)	-	10	Test
Cl.29.2 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation : Creepage distance )	-	10	Test
Cl.29.1 of IS 302-2-35:2017(Clearances, Creepage Distances and Solid Insulation : Clearance distance )	-	10	Test
Cl.28 of IS 302-2-35:2017(Screws and Connections )	-	10	Test
Cl.27.5 of IS 302-2-35:2017(Provision for Earthing : ECR )	-	10	Test
Cl.27 of IS 302-2-35:2017(Provision for Earthing)	-	10	Test
Cl.26 of IS 302-2-35:2017(Terminals for External Conductors)	-	10	Test
Cl.25.18 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	10	Test
Cl.25.15 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Cord grip test - displacement )	-	10	Test
Cl.25.15 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Cord grip test )	-	10	Test
Cl.25.12 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Moulding of supply cord )	-	10	Test
Cl.25.10 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Colour of Earthing conductor )	-	10	Test
Cl.25.8 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Resistance of supply cord )	-	10	Test
Cl.25.5 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : Type of attachment )	-	10	Test
Cl.25.1 of IS 302-2-35:2017(Supply Connection & External Flexible Cords : connection to the supply mains)	-	10	Test
Cl.25 of IS 302-2-35:2017(Supply Connection & External Flexible Cords)	-	10	Test
Cl.24 of IS 302-2-35:2017(Component )	-	10	Test
Cl.23 of IS 302-2-35:2017(Internal Wiring ; Colour of earthing conductor)	-	10	Test
Cl.23 of IS 302-2-35:2017(Internal Wiring)	-	10	Test
Cl.22.110 of IS 302-2-35:2017(Construction : Provision for fixing to wall )	-	10	Test
Cl.22.109 of IS 302-2-35:2017(Construction : Operation of presure switch of open outlet water heater )	-	10	Test
Cl.22.108 of IS 302-2-35:2017(Construction : Temperature of outlet water intended to supply for showring )	-	10	Test
Cl.22.107 of IS 302-2-35:2017(Construction : Temperature of outlet )	-	10	Test
Cl.22.106 of IS 302-2-35:2017(Construction : Operation of thermal cut out for closed water heater )	-	10	Test
Cl.22.104 of IS 302-2-35:2017(Construction : Pressure in open outlet water heaters )	-	10	Test
Cl.22.103 of IS 302-2-35:2017(Construction : Pressure relief device operation for closed water heater )	-	10	Test
Cl.22.102 of IS 302-2-35:2017(Construction : excessive temperature of outlet )	-	10	Test
Cl.22.101 of IS 302-2-35:2017(Construction : Rated pressure of closed water heater )	-	10	Test
Cl.22.47 of IS 302-2-35:2017(Construction : Water pressure test )	-	10	Test
Cl.22.44 of IS 302-1:2008(Construction : Shape and decoration )	-	10	Test
Cl.22.34, Cl 22.35 of IS 302-1:2008(Construction : Shaft of operating Knobs )	-	10	Test
Cl.22.33 of IS 302-1:2008(Construction : Direct contact of liquids )	-	10	Test
Cl 22.26 ,Cl.22.28, Cl 22.29, Cl 22.30 , Cl 22.31, Cl 22.32 of IS 302-1:2008(Construction : Supplymentry/ double / reinforced insulation for Class II/ Class III appliance )	-	10	Test
Cl.22.18 of IS 302-1:2008(Construction : Resistance to corrosion )	-	10	Test
Cl.22.17 of IS 302-1:2008(Construction : Spacers )	-	10	Test
Cl.22.14 of IS 302-1:2008(Construction : Ragged or sharp edges )	-	10	Test
Cl.22.12 of IS 302-1:2008(Construction : Fixing of Handle, knob, grips, levers and similar parts )	-	10	Test
Cl.22.11 of IS 302-1:2008(Construction : Fixing of non detachable parts )	-	10	Test
Cl.22.7 of IS 302-1:2008(Construction : safeguards against the risk of excessive pressure. )	-	10	Test
Cl.22.6 of IS 302-2-35:2017(Construction : size of drain hole )	-	10	Test
Cl.22.6 of IS 302-1:2008(Construction : effect of water on 3 insulation )	-	10	Test
Cl.22.2 of IS 302-1:2008(Construction : connection to supply mains )	-	10	Test
Cl.22.1 of IS 302-1:2008(Construction : IP test )	-	10	Test
Cl. 21.2 of IS 302-1:2008(Mechanical strength : prevent penetration by sharp implements. )	-	10	Test
Cl.21.1 of IS 302-1:2008(Mechanical strength : Rough handling in normal use)	-	10	Test
Cl.20 of IS 302-2-35:2017(Stability & Mechanical Hazards )	-	10	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation : effect on container)	-	10	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation : High voltage)	-	10	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Temperature rise of insulation of supply cord)	-	10	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Temperature rise of test corner)	-	10	Test
Cl.19 of IS 302-2-35:2017(Abnormal Operation : Emission of flames, molten metal ,or poisonous or ignitable gas)	-	10	Test
Cl.16 of IS 302-2-35:2017(Leakage Current and Electric Strength (After Humidity))	-	10	Test
Cl.16 of IS 302-2-35:2017(Leakage Current and Electric Strength (After Humidity))	-	10	Test
Cl.15 of IS 302-2-35:2017(Moisture Resistance )	-	10	Test
Cl.14 of IS 302-2-35:2017(Transient Over Voltages )	-	10	Test
Cl.13 of IS 302-2-35:2017(Leakage Current & 3 Strength at Operating Temperature : High voltage )	-	10	Test
Cl.13 of IS 302-2-35:2017(Leakage Current & 3 Strength at Operating Temperature )	-	10	Test
Cl.11 of 302-2-35:2017(Heating : room temperature)	-	10	Test
Cl.11 of 302-2-35:2017(Heating : Insulation of supply cord)	-	10	Test
Cl.11 of 302-2-35:2017(Heating : Temperature rise of test corner)	-	10	Test
Cl.10 of IS 302-2- 35:2017(Power Input & Current )	-	10	Test
Cl.8 of IS 302-2-35:2017(Protection Against Access To Live Parts)	-	10	Test
Cl.7.102 of IS 302-2-35:2017(Marking : Standard mark)	-	10	Test
Cl.7.101 of IS 302-2-35:2017(Marking : Woter inlet and outlet idetification)	-	10	Test
Cl.7.15 of IS 302-1:2008(Marking : Position of marking)	-	10	Test
Cl.7.14 of IS 302-1:2008(Marking ; Legibility and durability)	-	10	Test
Cl.7.13 of IS 302-1:2008(Marking : Language)	-	10	Test
Cl.7.10 & 7.11 of IS 302-1:2008(Marking : Indication for direction of control)	-	10	Test
Cl.7.8 of IS 302-1:2008(Marking : Terminal for connection )	-	10	Test
Cl.7.6 of IS 302-1:2008(Marking : Symbols)	-	10	Test
Cl.7.1 of IS 302-2-35:2017(Marking : rated pressure)	-	10	Test
Cl.7.1 of IS 302-1:2008(Marking : Country of manufacture)	-	10	Test
Cl.7.1 of IS 302-1:2008(Marking : IP number )	-	10	Test
Cl.7.1 of IS 302-1:2008(Marking : Symbol for class II)	-	10	Test
Cl.7.1 of IS 302-1:2008(Marking : Molel or type)	-	10	Test
Cl.7.1 of IS 302-1:2008(Marking : Manufacture identification)	-	10	Test
Cl.7.1 of IS 302-1:2008(Marking : Rated power input)	-	10	Test
Cl.7.1 of IS 302-1:2008(Marking : Nature of supply)	-	10	Test
Cl.7.1 of IS 302-1:2008(Marking : Rated Voltage)	-	10	Test
15.4 (b)(Cold impact)	-	10	Test

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

1100 VOLTS

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(CONDUCTOR: CONSTRUCTION)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
9.2(Thickness of Insulation - Average)	-	50	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
9.3(Thickness of Insulation - Minimum)	-	50	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
11(LAVING UP OF CORES)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
12.3(Thickness of Inner Sheath)	-	50	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.2(Type of armour )	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.3(Armouring : Dimensions -Wire Diameter)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.4(Armour: Joint)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.5(Armouring : Resistance Test)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.6 a)(ARMOURING: Tensile Strength)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.6 b)(ARMOURING: Elongation )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.6 f)(ARMOURING: Mass of zinc coating )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.6 g)(ARMOURING: Resistivity)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
14.3(Thickness of outer sheath - AVERAGE)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
14.3(Thickness of outer sheath - minimum)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 a) i)(Annealing Test ( For copper wire ) )	-	200	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	200	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	200	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 a) iii)(Wrapping test (for aluminium))	-	50	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 a) iv)(Resistance test - Main conductor)	-	200	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	250	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	250	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	1800	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	250	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	250	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) v) (Sheath : Hot deformation)	-	200	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) vi) (Sheath : Heat shock test)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) vii) (Sheath : Thermalstability)	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	200	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
16.2(HIGH VOLTAGE TEST )	-	250	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
16.3(FLAMMABILITY TEST : Period of Burning )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
16.3(FLAMMABILITY TEST : Unaffected length )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
17.3(cable Code )	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
3(CONDUCTOR: MATERIALS)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
4(INSULATION : MATERIALS)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
5.1(FILLER AND INNER SHEATH)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
6(ARMOURING)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
7(OUTER SHEATH)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
8.2(PROTECTIVE BARRIER)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
9.1(Insulation Applied by extrusicn)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
9.4(Application of Insulation)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
10.1(Core Identification)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
10.2(Core Identification- Neutral)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
10.3(Core Identification by number )	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
10.4(Core Identification by number - Neutral )	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
12.1 & 12.2(Inner sheath : Application)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.1(Armouring: Application)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.1.2(Armouring: Coverage )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.1.3(Armouring: Direction of Lay )	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
13.3(Armouring : Dimensions -Formed wire )	-	100	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
14.1(Outer Sheath : Application)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
14.2(Colour of outer sheath)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 a) iv)(Resistance test - Neutral conductor)	-	200	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	400	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
16.9(Oxygen Index Test)	-	1500	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
16.1(Flame Retardance Test on Single Cables)	-	2000	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
16.11(Flame Retardance Test on Bunched Cables)	-	3500	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
16.13(Test for Halogen Acid Gas Evolution)	-	1000	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
16.14(Temperature Index)	-	2000	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
17.1(Manufacturer'. identification)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
17.2(cable Indentification )	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.
5.2(FILLER AND INNER SHEATH)	-	10	Rs.7000/- for single core cable and Rs.1000/- for each additional core, Rs.1000/- for armouring, Rs.9000/- additional for FR and Rs.12000/- additional for FRLSH.

-
(C-1 & C-2 category included w.e.f. 23.02.2024)

IS 368 (2014)

Electric immersion water heaters - Specification (Fifth Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	200	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.8 of IS 302‐2-201: 2008(Protection Against Access to Live Parts)	-	200	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.10 of IS 302‐2‐201:2008(Power Input and Current )	-	500	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	700	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl. 12 of IS 368:2014(Operation under overload conditions of appliances with heating elements)	-	800	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.13 of IS 302-2-201: 2008(Leakage Current & Electric Strength at Operating Temperature)	-	700	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.14 of IS 302‐2-201:2008(Transient Over Voltages )	-	800	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	700	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	700	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.17 of IS 302‐2-201: 2008(Overload Protection of Transformers & Associated Circuits)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	500	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.20 of IS 302-2-201: 2008(Stability & Mechanical Hazards)	-	450	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	500	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.22 of IS 302-2-201: 2008(Construction)	-	450	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.23 of 302-2-201:2008(Internal Wiring )	-	150	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.24 of IS 302-2-201: 2008(Component)	-	200	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	550	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.26 of IS 302-2-201: 2008(Terminals for External Conductors)	-	600	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	500	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.28 of IS 302-2-201: 2008(Screws & Connections )	-	300	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.29 of IS 302-2‐201:2008(Clearances, Creepage Distances and Solid Insulation )	-	500	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.30 of IS 302-2‐201:2008(Resistance to Heat and Fire )	-	900	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.31 of IS 302-2-201:2008(Resistance of Rusting )	-	400	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.6 of IS 302-‐2-‐201:2008(Classification)	-	200	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.7 of IS 302-2-201:2008(Marking and Instruction )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.11 of IS 302-2201: 2008(Heating)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.13 of IS 302-2-201: 2009(Leakage Current & Electric Strength at Operating Temperature)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.15 of IS 302-2-201:2008(Moisture Resistance )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kWRs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.16 of IS 302-2-201:2008(Leakage Current & Electric Strength)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.18 of IS 368:2014(Endurance)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.19 of IS 302‐2-201: 2008(Abnormal Operation )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.21 of IS 302-2-201: 2008(Mechanical Strength )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.22 of IS 302-2-201: 2008(Construction)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.22 of IS 302-2-201: 2008(Construction)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.22 of IS 302-2-201: 2008(Construction)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.23 of 302-2-201:2008(Internal Wiring )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.24 of IS 302-2-201: 2008(Component)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.25 of IS 302-2-201: 2008(Supply Connection and External Flexible Cords)	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.27 of IS 302-2-201: 2008(Provision for Earthing )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.29 of IS 302-2‐201:2008(Clearances, Creepage Distances and Solid Insulation )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.30 of IS 302-2‐201:2008(Resistance to Heat and Fire )	-	0	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW
Cl.32 of IS 302-2-201:2008(Radiation, Toxicity and Similar Hazards)	-	200	Rs.12500 For up to 1.5kW and Rs.15000 above 1.5kW

-
-

First
Prev
1
2
3
4
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Alpha Test House Private Limited, Delhi

487/25, Near Prachin Shiv Mandir Peeragarhi, DELHI, New Delhi, Delhi, 110087

9711227171 electrical@alphatesthouse.com

Scope List