BIS - LIMS (Laboratory Information Management System)

ALPHA TEST HOUSE PRIVATE LIMITED

198-199, M.I.E, PHASE-I, BAHADURGARH, HARYANA-124507, Bahadurgarh, Jhajjar, Haryana, 124507

9711227171 info@alphatesthouse.com

Scope List

Reset

199 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

121

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	1000	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	1000	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	1000	-
10(Tensile test)	-	1000	-
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	1000	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	1000	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	0	-
10(Tensile test)	-	0	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	0	-

Complete

26 Aug, 2024

122

IS 2067 (1975)

Specification for wrought aluminium wire for electrical purposes (Fourth Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No 4("Chemical Composition")	-	2000	-
Clause No 5.1("Mechanical properties ")	-	1000	-
Clause No 6("Freedom from defects ")	-	500	-
Clause No 7.1(Electrical resistivity of the wire condition o, H3, H4)	-	1000	-
Clause No 8("Mechanical properties condition o, H3, H4")	-	500	-
Clause No 9(Joints)	-	0	-
Clause No 10.1(Tolerances (on size))	-	500	-
Clause No 12.1(Tensile test)	-	1000	-
Clause No 12.2(Elongation test)	-	500	-
Clause No 12.3(Wrapping test)	-	500	-
Clause No 12.4.1(Electrical resistivity shall be measured at room temp.)	-	2000	-
Clause No 15(Marking)	-	0	-

Complete

26 Aug, 2024

123

IS 1254 (2007)

Corrugated aluminium sheet (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(FREEDOM FROM DEFECTS)	-	1000	-
4(SUPPLY OF MATERIAL)	-	1000	-
5(PROFILE)	-	1000	-
6(MATERIAL)	-	1000	-
7.2(WIDTH)	-	1000	-
7.3(LENGTH)	-	1000	-
7.4(SQUARENESS)	-	1000	-
7.5(Depth and Pitch of the Corrugation)	-	1000	-
8(FINISH)	-	1000	-
9(MARKING)	-	1000	-
3(FREEDOM FROM DEFECTS)	-	1000	-
4(SUPPLY OF MATERIAL)	-	1000	-
5(PROFILE)	-	1000	-
6(MATERIAL)	-	1000	-
7.2(WIDTH)	-	1000	-
7.3(LENGTH)	-	0	-
7.4(SQUARENESS)	-	0	-
7.5(Depth and Pitch of the Corrugation)	-	0	-
8(FINISH)	-	0	-
9(MARKING)	-	0	-

Complete

26 Aug, 2024

124

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Freedom from defects)	-	1000	-
7.0(Dimension and Tolerances)	-	1000	-
8.1 Table-1(Al)	-	1000	-
8.1 Table-1(Cu)	-	1000	-
8.1 Table-1(Mg)	-	1000	-
8.1 Table-1(Si)	-	1000	-
8.1 Table-1(Fe)	-	1000	-
8.1 Table-1(Mn)	-	1000	-
8.1 Table-1(Zn)	-	1000	-
8.1 Table-1(Ti)	-	1000	-
8.1 Table-1(Cr)	-	1000	-
9.1(Tensile Strength)	-	1000	-
9.3(Wrapping Test)	-	1000	-
10(Selection of Test Samples)	-	1000	-
10(Selection of Test Samples)	-	1000	-
10(Selection of Test Samples)	-	0	-

Complete

26 Aug, 2024

125

IS 737 (2008)

Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes - Specification (Fourth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	1000	-
6 Table-1(Al)	-	1000	-
6 Table-1(Cu)	-	1000	-
6 Table-1(Mg)	-	1000	-
6 Table-1(Si)	-	1000	-
6 Table-1(Fe)	-	1000	-
6 Table-1(Mn)	-	1000	-
6 Table-1(Zn)	-	1000	-
6 Table-1(Ti)	-	1000	-
6 Table-1(Cr)	-	1000	-
6 Table-1(Cu+Si+Fe)	-	1000	-
6 Table-1(Cu+Si+Fe+Mn+Zn)	-	1000	-
6 Table-1(Cu+Mg+Si+Fe+Mn+Zn)	-	1000	-
6 Table-1(Zr)	-	1000	-
6 Table-1(Cr+Mn)	-	1000	-
7 Table-2(Tensile Strength)	-	1000	-
7 Table-2(Elongation)	-	1000	-
7 Table-2(0.2 % Proof Stress)	-	1000	-
7 Table-2(Bend Test)	-	1000	-
9(Dimension - IS 2676)	-	1000	-
12(Marking)	-	0	-
9(Dimension - IS 2676)	-	0	-
12(Marking)	-	0	-
9(Dimension - IS 2676)	-	0	-
12(Marking)	-	0	-

Complete

26 Aug, 2024

126

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	2000	-
5(chemical composition)	-	2000	-
6.1 table 2(0.2% proof strength)	-	2000	-
6.1 table 2(tensile strength)	-	2000	-
6.1 table 2(Elongation)	-	2000	-
8(Dimensions & Tolerances)	-	2000	-
4(Freedom from defect)	-	2000	-
5(chemical composition)	-	2000	-
6.1 table 2(0.2% proof strength)	-	2000	-
6.1 table 2(tensile strength)	-	0	-
6.1 table 2(Elongation)	-	0	-
8(Dimensions & Tolerances)	-	0	-
5.1, Table 1(Aluminium)	-	0	-
5.1, Table 1(Copper)	-	0	-
5.1, Table 1(Magnesium)	-	0	-
5.1, Table 1(Silicon)	-	0	-
5.1, Table 1(Iron)	-	0	-
5.1, Table 1(Mangnese)	-	0	-
5.1, Table 1(Zinc)	-	0	-
5.1, Table 1(Titanium and /or other grain refining element)	-	0	-
5.1, Table 1(Chromium)	-	0	-
5.1, Table 1(Vanadium)	-	0	-

Complete

26 Aug, 2024

127

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Freedom from Defects)	-	500	-
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	1500	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	1500	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	0	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	125	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	125	-
7(Dimension - IS 3965)	-	500	-
11(Marking)	-	0	-

Complete

26 Aug, 2024

128

IS 14810 (2000)

Copper tubes for plumbing - Specification

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4("General Requirements")	-	0	-
Clause 5(Supply of material)	-	0	-
Clause 6("Freedom from defects")	-	500	-
Clause 7(Chemical composition)	-	2000	-
Clause 10("DIMENSIONS AND TOLERANCES")	-	1500	-
Clause 11.1(Tensile Test)	-	2000	-
Clause 11.2(Drift Expanding Test)	-	5500	-
Clause 12(HYDROSTATIC TEST)	-	4000	-
Clause 13(Sampling and criteria for conformity)	-	0	-
Clause 14(Marking)	-	0	-
1()	-	0	-
Clause 4("General Requirements")	-	-	-
Clause 5(Supply of material)	-	-	-
Clause 6("Freedom from defects")	-	-	-
Clause 7(Chemical composition)	-	-	-
Clause 10("DIMENSIONS AND TOLERANCES")	-	-	-
Clause 11.1(Tensile Test)	-	-	-
Clause 11.2(Drift Expanding Test)	-	-	-
Clause 12(HYDROSTATIC TEST)	-	-	-
Clause 13(Sampling and criteria for conformity)	-	-	-
Clause 14(Marking)	-	-	-
1()	-	-	-

Complete

26 Aug, 2024

129

IS 1897 (2008)

Copper strip for electrical purposes - Specification (Third Revision)

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(SUPPLY OF MATERIAL)	-	2000	-
CLAUSE 6(CHEMICAL COMPOSITION)	-	2000	-
CLAUSE 8(MECHANICAL PROPERTIES)	-	2000	-
CLAUSE 8.2(Bend Test)	-	2000	-
CLAUSE 9(ELECTRICAL RESISTIVITY TEST)	-	2000	-
CLAUSE 10(TEST FOR CONTROLLED PROOF RESISTANCE (OPTIONAL))	-	2000	-
CLAUSE 11(DlMENSIONS AND TOLERANCES)	-	2000	-
CLAUSE 13(RETEST)	-	2000	-
CLAUSE 4(SUPPLY OF MATERIAL)	-	2000	-
CLAUSE 6(CHEMICAL COMPOSITION)	-	2000	-
CLAUSE 8(MECHANICAL PROPERTIES)	-	2000	-
CLAUSE 8.2(Bend Test)	-	2000	-
CLAUSE 9(ELECTRICAL RESISTIVITY TEST)	-	1000	-
CLAUSE 10(TEST FOR CONTROLLED PROOF RESISTANCE (OPTIONAL))	-	0	-
CLAUSE 11(DlMENSIONS AND TOLERANCES)	-	0	-
CLAUSE 13(RETEST)	-	0	-
CLAUSE 4(SUPPLY OF MATERIAL)	-	0	-
CLAUSE 6(CHEMICAL COMPOSITION)	-	0	-
CLAUSE 8(MECHANICAL PROPERTIES)	-	0	-
CLAUSE 8.2(Bend Test)	-	0	-
CLAUSE 9(ELECTRICAL RESISTIVITY TEST)	-	0	-
CLAUSE 10(TEST FOR CONTROLLED PROOF RESISTANCE (OPTIONAL))	-	0	-
CLAUSE 11(DlMENSIONS AND TOLERANCES)	-	0	-
CLAUSE 13(RETEST)	-	0	-
Cl. 8.3(Edgewise bending,)	-	0	-
Cl. 8.3(Thickness)	-	0	-
Cl. 8.3(Tensile)	-	0	-
Cl. 8.3(Elongation)	-	0	-
Cl. 8.3(Hardness)	-	0	-

Complete

26 Aug, 2024

130

IS 208 (2020)

Door Handles - Specification ( Sixth Revision )

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(PACKING)	-	0	-
9.1(BIS Certification Marking)	-	0	-
9(MARKING)	-	0	-
6.2(Tolerance)	-	1400	-
6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size 1. No. in each Lug 2. No. in a plate when a continious plate is used 3. Size Designation of Counter-sunk Head Wood Screws (as per IS 6760: 1972))	-	1400	-
6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-	1400	-
5.1(MANUFACTURE- General)	-	0	-
3(TYPES-Doors handle shall be of the following types according to the materials used:)	-	1000	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Zinc- IS 2600:1964)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Nickel- IS 2600:1964)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Thallium and Indium- IS 2600:1964)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Tin- IS 2600:1964)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Cadmium- IS 2600:1964)	-	0	-
Cl.5.1(General)	-	0	-
Cl.6(Dimension)	-	1400	-
Cl.7(Finish)	-	0	-
Cl.8.2(Cossosion Test)	-	1000	-
Cl.8.3(Quench Test)	-	1000	-
Cl.9(Sampling and criterion for conformity)	-	1000	-
Cl.10(Marking)	-	0	-
Cl.11(Packing)	-	0	-
10(PACKING)	-	0	-
9.1(BIS Certification Marking)	-	0	-
9(MARKING)	-	0	-
6.2(Tolerance)	-	0	-
6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size 1. No. in each Lug 2. No. in a plate when a continious plate is used 3. Size Designation of Counter-sunk Head Wood Screws (as per IS 6760: 1972))	-	0	-
6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-	0	-
5.1(MANUFACTURE- General)	-	0	-
3(TYPES-Doors handle shall be of the following types according to the materials used:)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Zinc- IS 2600:1964)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Nickel- IS 2600:1964)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Thallium and Indium- IS 2600:1964)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Tin- IS 2600:1964)	-	0	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Cadmium- IS 2600:1964)	-	0	-
Cl.5.1(General)	-	0	-
Cl.6(Dimension)	-	0	-
Cl.7(Finish)	-	0	-
Cl.8.2(Cossosion Test)	-	0	-
Cl.8.3(Quench Test)	-	0	-
Cl.9(Sampling and criterion for conformity)	-	0	-
Cl.10(Marking)	-	0	-
Cl.11(Packing)	-	0	-

Complete

26 Aug, 2024

131

IS 613 (2000)

Copper rods and bars for electrical purposes - Specification (Third Revision)

9900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause no.3(SUPPLY OF MATERIAL)	-	100	-
Clause no.6(FREEDOM FROM DEFECTS)	-	500	-
Clause no.7(CONDITION OF SUPPLY)	-	1000	-
Clause no.8(CHEMICAL COMPOSITION)	-	2000	-
Clause no.9.1, table no,1(" tensile test ")	-	1000	-
Clause no.9.2(Bend test)	-	1000	-
"Clause no.10.1 and 11.1.1 Table No. 2"(Dimensions and Tolerances)	-	1000	-
"Clause no.10.2 and Table No. 3"("Tolerances on Length of Bar Rod in Straight Length ")	-	1000	-
"Clause no.10.4 and Table No. 4"(Corner Radius and Tolerances)	-	1000	-
"Clause no.11 and Table No. 5"(Electrical Resistivity)	-	1400	-
Clause no. 13(packing)	-	100	-
Clause no. 14(Marking)	-	100	-
Clause no.3(SUPPLY OF MATERIAL)	-	100	-
Clause no.6(FREEDOM FROM DEFECTS)	-	500	-
Clause no.7(CONDITION OF SUPPLY)	-	1000	-
Clause no.8(CHEMICAL COMPOSITION)	-	2000	-
Clause no.9.1, table no,1(" tensile test ")	-	1000	-
Clause no.9.2(Bend test)	-	1000	-
"Clause no.10.1 and 11.1.1 Table No. 2"(Dimensions and Tolerances)	-	1000	-
"Clause no.10.2 and Table No. 3"("Tolerances on Length of Bar Rod in Straight Length ")	-	1000	-
"Clause no.10.4 and Table No. 4"(Corner Radius and Tolerances)	-	1000	-
"Clause no.11 and Table No. 5"(Electrical Resistivity)	-	1400	-
Clause no. 13(packing)	-	100	-
Clause no. 14(Marking)	-	100	-
Clause no.3(SUPPLY OF MATERIAL)	-	100	-
Clause no.6(FREEDOM FROM DEFECTS)	-	500	-
Clause no.7(CONDITION OF SUPPLY)	-	1000	-
Clause no.8(CHEMICAL COMPOSITION)	-	2000	-
Clause no.9.1, table no,1(" tensile test ")	-	1000	-
Clause no.9.2(Bend test)	-	1000	-
"Clause no.10.1 and 11.1.1 Table No. 2"(Dimensions and Tolerances)	-	1000	-
"Clause no.10.2 and Table No. 3"("Tolerances on Length of Bar Rod in Straight Length ")	-	1000	-
"Clause no.10.4 and Table No. 4"(Corner Radius and Tolerances)	-	1000	-
"Clause no.11 and Table No. 5"(Electrical Resistivity)	-	1400	-
Clause no. 13(packing)	-	100	-
Clause no. 14(Marking)	-	100	-
Clause no.3(SUPPLY OF MATERIAL)	-	0	-
Clause no.6(FREEDOM FROM DEFECTS)	-	0	-
Clause no.7(CONDITION OF SUPPLY)	-	0	-
Clause no.8(CHEMICAL COMPOSITION)	-	0	-
Clause no.9.1, table no,1(" tensile test ")	-	0	-
Clause no.9.2(Bend test)	-	0	-
"Clause no.10.1 and 11.1.1 Table No. 2"(Dimensions and Tolerances)	-	0	-
"Clause no.10.2 and Table No. 3"("Tolerances on Length of Bar Rod in Straight Length ")	-	0	-
"Clause no.10.4 and Table No. 4"(Corner Radius and Tolerances)	-	0	-
"Clause no.11 and Table No. 5"(Electrical Resistivity)	-	0	-
Clause no. 13(packing)	-	0	-
Clause no. 14(Marking)	-	0	-
Clause no.3(SUPPLY OF MATERIAL)	-	0	-
Clause no.6(FREEDOM FROM DEFECTS)	-	0	-
Clause no.7(CONDITION OF SUPPLY)	-	0	-
Clause no.8(CHEMICAL COMPOSITION)	-	0	-
Clause no.9.1, table no,1(" tensile test ")	-	0	-
Clause no.9.2(Bend test)	-	0	-
"Clause no.10.1 and 11.1.1 Table No. 2"(Dimensions and Tolerances)	-	0	-
"Clause no.10.2 and Table No. 3"("Tolerances on Length of Bar Rod in Straight Length ")	-	0	-
"Clause no.10.4 and Table No. 4"(Corner Radius and Tolerances)	-	0	-
"Clause no.11 and Table No. 5"(Electrical Resistivity)	-	0	-
Clause no. 13(packing)	-	0	-
Clause no. 14(Marking)	-	0	-

Complete

26 Aug, 2024

132

IS 3818 (1992)

Continuous (Piano) hinges -Specification

5900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 (Ref. Cl.9 of IS 1868:1996)(Anodic casting thickness (Cl. 9.2 of IS 1868:1996))	-	900	-
4-Fig 1(DIMENSIONS AND TOLERANCES-Nominal Size)	-	1000	-
4-Fig 1(DIMENSIONS AND TOLERANCES-B)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-C)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-D)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-T)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES- Other Dimensions)	-	0	-
4-Fig 2(DIMENSIONS AND TOLERANCES-CoNTINUOUS ( PIANO) HINGIS TYPB III; 50 min NOMINAL SID)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B1)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B2)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-C)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-D)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-T)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	0	-
5.1(MANUFACTURE)	-	0	-
5.2(MANUFACTURE-Knuekles)	-	1000	-
5.2(MANUFACTURE-Knuekles)	-	0	-
5.3(MANUFACTURE-Pins)	-	1000	-
5.3(MANUFACTURE-Pins)	-	0	-
5.3(MANUFACTURE-Pin-Anodized thickness)	-	0	-
5.3(MANUFACTURE-Pins)	-	1000	-
5.4(MANUFACTURE-Screw Holes)	-	1000	-
6(Finish)	-	0	-
Cl. 6 (Ref. Cl.9 of IS 1868:1996)(Anodic casting thickness (Cl. 9.2 of IS 1868:1996))	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-Nominal Size)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-B)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-C)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-D)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-T)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap)	-	0	-
4-Fig 1(DIMENSIONS AND TOLERANCES- Other Dimensions)	-	0	-
4-Fig 2(DIMENSIONS AND TOLERANCES-CoNTINUOUS ( PIANO) HINGIS TYPB III; 50 min NOMINAL SID)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B1)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B2)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-C)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-D)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-T)	-	0	-
4-Fig 3(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	0	-
5.1(MANUFACTURE)	-	0	-
5.2(MANUFACTURE-Knuekles)	-	0	-
5.2(MANUFACTURE-Knuekles)	-	0	-
5.3(MANUFACTURE-Pins)	-	0	-
5.3(MANUFACTURE-Pins)	-	0	-
5.3(MANUFACTURE-Pin-Anodized thickness)	-	0	-
5.3(MANUFACTURE-Pins)	-	0	-
5.4(MANUFACTURE-Screw Holes)	-	0	-
6(Finish)	-	0	-

Complete

26 Aug, 2024

133

IS 12817 (2020)

Stainless Steel Butt Hinges - Specification ( Third Revision )

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2, Table 1 to 6(Length , A -IS 12817)	-	1000	-
6.2, Table 1 to 6(Breadth, B-IS 12817)	-	1000	-
6.2, Table 1 to 6(Breadth, B1-IS 12817)	-	1000	-
6.2, Table 1 to 6(Breadth, B2-IS 12817)	-	1000	-
6.2, Table 1 to 6(Thickness of flap, C-IS 12817)	-	1000	-
6.2, Table 1 to 6(Dia. of Hinge pin, D-IS 12817 )	-	1000	-
6.2, Table 1 to 6(Number of Knuckles- IS 12817 )	-	1000	-
6.2, Table 1 to 6(Number of Screw Holes -IS 12817 )	-	1000	-
6.2, Table 1 to 6(Holes for Screw Number- IS 12817 )	-	1000	-
7.1(General - IS 12817 )	-	1000	-
7.2(Knuckles - IS 12817 )	-	1000	-
7.3(Pins- IS 12817 )	-	1000	-
7.4(Screw Holes- IS 12817 )	-	1000	-
7.4.2(Position of screw holes - IS 12817 )	-	1000	-
7.4.2, Fig 1(The distance of the screw holes from the end of the flap - IS 12817 )	-	1000	-
8.0(Finish - IS 12817 )	-	0	-
Clause 4.1.2(Silicon (Pin) )	-	0	-
Clause 4.1.2(Phosphorus (Pin) )	-	0	-
Clause 4.1.2(Sulphur (Pin) )	-	0	-
Clause 4.1.2(Manganese (Pin) )	-	0	-
Clause 4.1.2(Carbon (Pin) )	-	0	-
Clause 4.1.1(Silicon (Flap) )	-	0	-
Clause 4.1.1(Phosphorus (Flap) )	-	0	-
Clause 4.1.1(Sulphur (Flap) )	-	0	-
Clause 4.1.1(Manganese (Flap) )	-	0	-
Clause 4.1.1(Carbon (Flap) )	-	0	-
Clause 7.4.2 (Dimension - Z )	-	1000	-
Clause 7.4.2 (Dimension - Y )	-	0	-
Clause 7.4.2 (Dimension - X )	-	0	-
Clause 7.4.1(Number of holes)	-	0	-
As per Cl.4(Carbon)	-	0	-
As per Cl.4(Sulphur)	-	0	-
As per Cl.4(Phosphorus)	-	0	-
As per Cl.4(Manganese)	-	0	-
As per Cl.4(Nitrogen)	-	0	-
As per Cl.4(Silicon)	-	0	-
As per Cl.4(Aluminium)	-	0	-
As per Cl.4(Chromium)	-	0	-
As per Cl.4(Vanadium)	-	0	-
As per Cl.4(Molybdenum)	-	0	-
As per Cl.4(Niobium)	-	0	-
As per Cl.4(Nickel)	-	0	-
As per Cl.4(Copper)	-	0	-
As per Cl.4(Titanium)	-	0	-
As per Cl.4(Zirconium)	-	0	-
As per Cl.4(Tungsten)	-	0	-
As per Cl.4(Cerium)	-	0	-
Clause 4.1.2(Silicon (Pin) )	-	0	-
Clause 4.1.2(Phosphorus (Pin) )	-	0	-
Clause 4.1.2(Sulphur (Pin) )	-	0	-
Clause 4.1.2(Manganese (Pin) )	-	0	-
Clause 4.1.2(Carbon (Pin) )	-	0	-
Clause 4.1.1(Silicon (Flap) )	-	0	-
Clause 4.1.1(Phosphorus (Flap) )	-	0	-
Clause 4.1.1(Sulphur (Flap) )	-	0	-
Clause 4.1.1(Manganese (Flap) )	-	0	-
Clause 4.1.1(Carbon (Flap) )	-	0	-
Clause 7.4.2 (Dimension - Z )	-	0	-
Clause 7.4.2 (Dimension - Y )	-	0	-
Clause 7.4.2 (Dimension - X )	-	0	-
Clause 7.4.1(Number of holes)	-	0	-
As per Cl.4(Carbon)	-	0	-
As per Cl.4(Sulphur)	-	0	-
As per Cl.4(Phosphorus)	-	0	-
As per Cl.4(Manganese)	-	0	-
As per Cl.4(Nitrogen)	-	0	-
As per Cl.4(Silicon)	-	0	-
As per Cl.4(Aluminium)	-	0	-
As per Cl.4(Chromium)	-	0	-
As per Cl.4(Vanadium)	-	0	-
As per Cl.4(Molybdenum)	-	0	-
As per Cl.4(Niobium)	-	0	-
As per Cl.4(Nickel)	-	0	-
As per Cl.4(Copper)	-	0	-
As per Cl.4(Titanium)	-	0	-
As per Cl.4(Zirconium)	-	0	-
As per Cl.4(Tungsten)	-	0	-
As per Cl.4(Cerium)	-	0	-

Complete

26 Aug, 2024

134

IS 3843 (1995)

Steel back flap hinges -Specification

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 6, Table 1, Table 2(Dimensions)	-	3000	-
Clause 4 Table 3(i)(Flap)	-	1500	-
Clause 4 Table 3(ii)(Pin)	-	1500	-
Clause 5(Dimension and tolerance)	-	2000	-
Clause 8(Marking)	-	0	-
Clause 9(Packing)	-	0	-
5, 6, Table 1, Table 2(Dimensions)	-	-	-
Clause 4 Table 3(i)(Flap)	-	-	-
Clause 4 Table 3(ii)(Pin)	-	-	-
Clause 5(Dimension and tolerance)	-	-	-
Clause 8(Marking)	-	-	-
Clause 9(Packing)	-	-	-

Complete

26 Aug, 2024

135

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

7800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
TABLE-1 (Clause-4)(TITANIUM)	-	800	-
TABLE-1 (Clause-4)(VANADIUM)	-	1000	-
TABLE-1 (Clause-4)(NIOBIUM)	-	1000	-
TABLE-1 (Clause-4)(Molybdenum)	-	1000	-
TABLE-1 (Clause-4)(Chromium)	-	1000	-
TABLE-1 (Clause-4)(Nickel)	-	1000	-
TABLE-1 (Clause-4)( ALUMINIUM)	-	1000	-
TABLE-1 (Clause-4)(SILICON)	-	1000	-
TABLE-1 (Clause-4)(NITROGEN)	-	0	-
TABLE-1 (Clause-4)(MANGANESE)	-	0	-
TABLE-1 (Clause-4)(PHOSPHURS)	-	0	-
Clause 4 Table 1(Sulphur ( Flap))	-	0	-
Clause 4 Table 1(Carbon ( Flap))	-	0	-
Cl 4 & Table 1(Sulphur- IS 228(Part 9))	-	0	-
Cl 4 & Table 1(Carbon- IS 228(Part 1))	-	0	-
Cl 4 & Table 1(Phosphorous- IS 228(Part 3))	-	0	-
Cl 4 & Table 1(Manganese- IS 228(Part 2))	-	0	-
Cl 4 & Table 1(Silicon- IS 228(Part 2))	-	0	-
Cl 4 & Table 1(Nitrogen -IS 228(Part 19))	-	0	-
3 Tables 2 to 9(Types)	-	0	-
5.1 Tables 2 to 9 (2)(Size of Hinge)	-	0	-
5.1 Tables 2 to 9 (3)(Length A)	-	0	-
5.1 Tables 2 to 9 (4)(Breadth B)	-	0	-
5.1 Tables 2 to 9 (4)(Breadth B1)	-	0	-
5.1 Tables 2 to 9 (4)(Breadth B2)	-	0	-
5.1 Tables 2 to 9 (5)(Thickness of Flap C)	-	0	-
5.1 Tables 2 to 9 (6)(Diameter of Hinge Pin D)	-	0	-
5.1 Tables 2 to 9 (7)(Number of Knuckles)	-	0	-
5.1 Tables 2 to 9 (8)(Number of Screw Holes)	-	0	-
5.1 Tables 2 to 9 (9)(Holes for Screw No.)	-	0	-
6.1(General)	-	0	-
6.1(General)	-	0	-
6.1(General)	-	0	-
6.2.1(Knuckles)	-	0	-
6.3(Pins)	-	0	-
6.4(Screw Holes)	-	0	-
6.4.2(Position of Holes)	-	0	-
6.4.2(X)	-	0	-
6.4.2(Y)	-	0	-
6.4.2(Z)	-	0	-
6.4.2.1(Position of Holes)	-	0	-
7(Finish)	-	250	-
8(Marking)	-	0	-
TABLE-1 (Clause-4)(SULPHUR)	-	0	-
TABLE-1 (Clause-4)( CARBON)	-	0	-
Clause 4 Table 1(Manganese ( Pin))	-	0	-
Clause 4 Table 1(Phosphorus ( Pin))	-	0	-
Clause 4 Table 1(Nitrogen ( Flap))	-	0	-
Clause 4 Table 1(Manganese ( Flap))	-	0	-
Clause 4 Table 1(Phosphorus ( Flap))	-	0	-
Clause 4 Table 1(Sulphur ( Pin))	-	0	-
Clause 4 Table 1(Carbon ( Pin))	-	0	-
Clause 4 Table 1(Sulphur ( Flap))	-	0	-
Clause 4 Table 1(Carbon ( Flap))	-	0	-
Cl 4 & Table 1(Sulphur- IS 228(Part 9))	-	0	-
Cl 4 & Table 1(Carbon- IS 228(Part 1))	-	0	-
Cl 4 & Table 1(Phosphorous- IS 228(Part 3))	-	0	-
Cl 4 & Table 1(Manganese- IS 228(Part 2))	-	0	-
Cl 4 & Table 1(Silicon- IS 228(Part 2))	-	0	-
Cl 4 & Table 1(Nitrogen -IS 228(Part 19))	-	0	-
3 Tables 2 to 9(Types)	-	0	-
5.1 Tables 2 to 9 (2)(Size of Hinge)	-	0	-
5.1 Tables 2 to 9 (3)(Length A)	-	0	-
5.1 Tables 2 to 9 (4)(Breadth B)	-	0	-
5.1 Tables 2 to 9 (4)(Breadth B1)	-	0	-
5.1 Tables 2 to 9 (4)(Breadth B2)	-	0	-
5.1 Tables 2 to 9 (5)(Thickness of Flap C)	-	0	-
5.1 Tables 2 to 9 (6)(Diameter of Hinge Pin D)	-	0	-
5.1 Tables 2 to 9 (7)(Number of Knuckles)	-	0	-
5.1 Tables 2 to 9 (8)(Number of Screw Holes)	-	0	-
5.1 Tables 2 to 9 (9)(Holes for Screw No.)	-	0	-
6.1(General)	-	0	-
6.1(General)	-	0	-
6.1(General)	-	0	-
6.2.1(Knuckles)	-	0	-
6.3(Pins)	-	0	-
6.4(Screw Holes)	-	0	-
6.4.2(Position of Holes)	-	0	-
6.4.2(X)	-	0	-
6.4.2(Y)	-	0	-
6.4.2(Z)	-	0	-
6.4.2.1(Position of Holes)	-	0	-
7(Finish)	-	0	-
8(Marking)	-	0	-
Clause 4 Table 1(Manganese ( Pin))	-	0	-
Clause 4 Table 1(Phosphorus ( Pin))	-	0	-
Clause 4 Table 1(Nitrogen ( Flap))	-	0	-
Clause 4 Table 1(Manganese ( Flap))	-	0	-
Clause 4 Table 1(Phosphorus ( Flap))	-	0	-
Clause 4 Table 1(Sulphur ( Pin))	-	0	-
Clause 4 Table 1(Carbon ( Pin))	-	0	-

Complete

26 Aug, 2024

136

IS 453 (1993)

Double Acting Spring Hinges -Specification

27000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(DIMENSIONS)	-	1500	-
9(PERFORMANCE TESTS)	-	1500	-
Clause 5(Sizes)	-	1500	-
Clause 8(Finish)	-	1500	-
Clause 10(Marking)	-	1500	-
Clause 11(Packing)	-	1500	-
Clause 6(Dimensions)	-	1000	-
Clause 9(Performance Test)	-	1000	-
Clause 4.1(Mild Steel Sheet)	-	1000	-
Clause 4.2(Mild Steel Wire)	-	1000	-
Clause 4.3(Cast Brass)	-	1000	-
Clause 4.4(Brass Sheets)	-	1000	-
Clause 4.7(Phosphor Bronze Wire)	-	1000	-
Clause 4.5(Brass Rods)	-	1000	-
Clause 4.6(Steel Wire)	-	1000	-
6(DIMENSIONS)	-	1000	-
9(PERFORMANCE TESTS)	-	1000	-
Clause 4.1(Mild Steel Sheet)	-	1000	-
Clause 4.2(Mild Steel Wire)	-	1000	-
Clause 4.3(Cast Brass)	-	1000	-
Clause 4.4(Brass Sheets)	-	1000	-
Clause 4.5(Brass Rods)	-	1000	-
Clause 4.6(Steel Wire)	-	1000	-
Clause 4.7(Phosphor Bronze Wire)	-	1000	-
Clause 5(Sizes)	-	0	-
Clause 6(Dimensions)	-	0	-
Clause 8(Finish)	-	0	-
Clause 9(Performance Test)	-	0	-
Clause 10(Marking)	-	0	-
Clause 11(Packing)	-	0	-
Cl-7.1(Mild Steel Hinges)	-	0	-
Cl-7.1.1(Blank hinge shall be made from mild steel sheet)	-	0	-
Cl-7.2(Brass Hinges)	-	0	-
Cl-7.2.1(Blank hinges shall be made of cast brass)	-	0	-
6(DIMENSIONS)	-	0	-
9(PERFORMANCE TESTS)	-	0	-
Clause 4.1(Mild Steel Sheet)	-	0	-
Clause 4.2(Mild Steel Wire)	-	0	-
Clause 4.3(Cast Brass)	-	0	-
Clause 4.4(Brass Sheets)	-	0	-
Clause 4.5(Brass Rods)	-	0	-
Clause 4.6(Steel Wire)	-	0	-
Clause 4.7(Phosphor Bronze Wire)	-	0	-
Clause 5(Sizes)	-	0	-
Clause 6(Dimensions)	-	0	-
Clause 8(Finish)	-	0	-
Clause 9(Performance Test)	-	0	-
Clause 10(Marking)	-	0	-
Clause 11(Packing)	-	0	-
Cl-7.1(Mild Steel Hinges)	-	0	-
Cl-7.1.1(Blank hinge shall be made from mild steel sheet)	-	0	-
Cl-7.2(Brass Hinges)	-	0	-
Cl-7.2.1(Blank hinges shall be made of cast brass)	-	0	-

Complete

26 Aug, 2024

137

IS 362 (1991)

Parliament Hinges -specification

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Type)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Size)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Holes for screw designation)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-No. of Screw holes)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Holes for screw designation)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Size)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-A)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-B)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-C)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-D)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-d)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-E)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Thickness of Flap)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-No. of Screw holes)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Holes for screw designation)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Size)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-A)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-B)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-C)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-D)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-d)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-E)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Thickness of Flap)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-No. of Screw holes)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.4(MANUFACTURE-Screw Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the ends of the flap)	-	0	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the inner edge)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
7.1(FINISH)	-	0	-
7.3(FINISH)	-	0	-
Cl. 7.1 (Brass parliament hinges shall have either bright or satin finish and shall be suitably protected against discoloration)	-	0	-
Cl. 7.2 (Ref. Cl. 11.1 of IS 1868:1996)( appearance and Colour - shall be free from visible defects on the significant surface(s) when viewed from an agreed distance)	-	0	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Aluminium shall be anodized to a bright, natural, sat or satin finish or dyed. )	-	0	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	0	-
Cl. 7.3(Mild steel parliament hinges shall be finished bright or electro-galvanized as specified by the purchaser)	-	0	-
Cl. 7.1 (Brass parliament hinges shall have either bright or satin finish and shall be suitably protected against discoloration)	-	0	-
Cl. 7.2 (Ref. Cl. 11.1 of IS 1868:1996)( appearance and Colour - shall be free from visible defects on the significant surface(s) when viewed from an agreed distance)	-	0	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Aluminium shall be anodized to a bright, natural, sat or satin finish or dyed. )	-	0	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	0	-
Cl. 7.3(Mild steel parliament hinges shall be finished bright or electro-galvanized as specified by the purchaser)	-	0	-
3(Type)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Size)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-No. of Screw holes)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Holes for screw designation)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Size)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-A)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-B)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-C)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-D)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-d)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-E)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Thickness of Flap)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-No. of Screw holes)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Holes for screw designation)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Size)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-A)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-B)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-C)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-D)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-d)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-E)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Thickness of Flap)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-No. of Screw holes)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Holes for screw designation)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.4(MANUFACTURE-Screw Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the ends of the flap)	-	0	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the inner edge)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
7.1(FINISH)	-	0	-
7.3(FINISH)	-	0	-
Cl. 7.1 (Brass parliament hinges shall have either bright or satin finish and shall be suitably protected against discoloration)	-	0	-
Cl. 7.2 (Ref. Cl. 11.1 of IS 1868:1996)( appearance and Colour - shall be free from visible defects on the significant surface(s) when viewed from an agreed distance)	-	0	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Aluminium shall be anodized to a bright, natural, sat or satin finish or dyed. )	-	0	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	0	-
Cl. 7.3(Mild steel parliament hinges shall be finished bright or electro-galvanized as specified by the purchaser)	-	0	-
3(Type)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Size)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-No. of Screw holes)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Holes for screw designation)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Size)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-A)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-B)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-C)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-D)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-d)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-E)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Thickness of Flap)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-No. of Screw holes)	-	0	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Holes for screw designation)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Size)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-A)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-B)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-C)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-D)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-d)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-E)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Thickness of Flap)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-No. of Screw holes)	-	0	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Holes for screw designation)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.1(MANUFACTURE-General)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.2(MANUFACTURE-Knuckles)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.3(MANUFACTURE-Pins)	-	0	-
6.4(MANUFACTURE-Screw Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the ends of the flap)	-	0	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the inner edge)	-	0	-
6.5(MANUFACTURE-Position of Holes)	-	0	-
7.1(FINISH)	-	0	-
7.3(FINISH)	-	0	-
3(Type)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Size)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-	0	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-	500	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-	500	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-	500	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-	500	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-	500	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-	500	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-No. of Screw holes)	-	500	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Holes for screw designation)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Size)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-A)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-B)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-C)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-D)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-d)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-E)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Thickness of Flap)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-No. of Screw holes)	-	500	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Holes for screw designation)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Size)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-A)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-B)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-C)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-D)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-d)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-E)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Thickness of Flap)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-No. of Screw holes)	-	500	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Holes for screw designation)	-	500	-
3(Type)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Size)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-No. of Screw holes)	-	-	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Holes for screw designation)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Size)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-A)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-B)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-C)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-D)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-d)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-E)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Thickness of Flap)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-No. of Screw holes)	-	-	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Holes for screw designation)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Size)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-A)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-B)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-C)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-D)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-d)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-E)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Thickness of Flap)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-No. of Screw holes)	-	-	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Holes for screw designation)	-	-	-
6.1(MANUFACTURE-General)	-	-	-
6.1(MANUFACTURE-General)	-	-	-
6.1(MANUFACTURE-General)	-	-	-
6.2(MANUFACTURE-Knuckles)	-	-	-
6.2(MANUFACTURE-Knuckles)	-	-	-
6.2(MANUFACTURE-Knuckles)	-	-	-
6.2(MANUFACTURE-Knuckles)	-	-	-
6.3(MANUFACTURE-Pins)	-	-	-
6.3(MANUFACTURE-Pins)	-	-	-
6.3(MANUFACTURE-Pins)	-	-	-
6.3(MANUFACTURE-Pins)	-	-	-
6.4(MANUFACTURE-Screw Holes)	-	-	-
6.5(MANUFACTURE-Position of Holes)	-	-	-
6.5(MANUFACTURE-Position of Holes)	-	-	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the ends of the flap)	-	-	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the inner edge)	-	-	-
6.5(MANUFACTURE-Position of Holes)	-	-	-
7.1(FINISH)	-	-	-
7.3(FINISH)	-	-	-
Cl. 7.1 (Brass parliament hinges shall have either bright or satin finish and shall be suitably protected against discoloration)	-	-	-
Cl. 7.2 (Ref. Cl. 11.1 of IS 1868:1996)( appearance and Colour - shall be free from visible defects on the significant surface(s) when viewed from an agreed distance)	-	-	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Aluminium shall be anodized to a bright, natural, sat or satin finish or dyed. )	-	-	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	-	-
Cl. 7.3(Mild steel parliament hinges shall be finished bright or electro-galvanized as specified by the purchaser)	-	-	-

Complete

26 Aug, 2024

138

IS 206 (2010)

Tee and strap hinges - Specification (Fifth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(DIMENSIONS AND TOLERANCES)	-	3500	-
6(WORKMANSHIP)	-	500	-
7(FINISH)	-	500	-
10(MARKING)	-	500	-
Clause 3.1,1(Light weight (Type 1))	-	500	-
Clause 3.1,2(Light weight (Type 2))	-	500	-
Clause 3.1,3(Medium weight (Type 1))	-	500	-
Clause 3.1,4(Medium weight (Type 2))	-	500	-
Clause 3.1,5(Heavy weight (Type 1))	-	500	-
Clause 3.1,6(Heavy weight (Type 2))	-	100	-
Clause 3.1,7(Heavy weight (Type 3))	-	100	-
Clause 3.2,1(Light weight)	-	100	-
Clause 3.2,2(Medium weight (Type 1))	-	100	-
Clause 3.2,3(Medium weight (Type 2))	-	100	-
Clause 3.2,4(Heavy weight )	-	0	-
Clause 4 Table 1(i)(Mild steel sheet)	-	0	-
Clause 4 Table 1(ii)(Mild steel wire)	-	0	-
Clause 5.1(Dimensions)	-	0	-
Clause 6(Workmanship)	-	0	-
Clause 8(Packing)	-	0	-
Clause 9(SAMPLING AND CRITERION FOR CONFORMITY)	-	0	-
Clause 10(Marking)	-	0	-

Complete

26 Aug, 2024

139

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

7650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	100	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	100	-
5.2 ,Table 6(Tolerances-Tolerances on dimensions of hinges )	-	100	-
6.2- Table 2,3,4,5 (Kunckles)	-	100	-
6.3(Screw Holes)	-	100	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	100	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	100	-
6.3.3 Fig-1(Position of Holes)	-	100	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	100	-
8.2(Packing -Each Package shall bear the following Particulars)	-	100	-
7(Workmanship & Finish)	-	100	-
10(Marking)	-	100	-
6.1(Manufacture- General)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	100	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	100	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	100	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	100	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Copper - IS 3685:1966)	-	100	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Lead - IS 3685:1966)	-	100	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Iron - IS 3685:1966)	-	100	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	100	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Zinc- IS 3685:1966)	-	100	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	100	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	100	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	100	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	100	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	100	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	100	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	100	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	100	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	100	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	100	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	100	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Tin - IS 4027:1967)	-	100	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Phosphorous - IS 4027:1967)	-	100	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Lead - IS 4027:1967)	-	100	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Total impurities - IS 4027:1967)	-	100	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Copper - IS 4027:1967)	-	100	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Carbon - IS 228)	-	100	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Silicon - IS 228)	-	100	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Sulphur - IS 228)	-	100	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Phosphorous - IS 228)	-	100	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Silicon - IS 228 (optional))	-	100	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Tota Aluminium - IS 228 (optional))	-	100	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Lead - IS 3685:1966)	-	100	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Iron - IS 3685:1966)	-	100	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Total impurities - IS 3685:1966)	-	100	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Zinc - IS 3685:1966)	-	100	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Carbon - IS 228)	-	100	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Manganese - IS 228)	-	100	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Nickel - IS 228)	-	100	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Chromium - IS 228)	-	100	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Molybdenum - IS 228)	-	100	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Sulphur - IS 228)	-	100	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Phosphorous - IS 228)	-	100	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Manganese - IS 228)	-	100	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Copper - IS 3685:1966)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	100	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	100	-
3(TYPES)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	100	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	100	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	100	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	50	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Copper - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Lead - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	0	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Zinc- IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	0	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	0	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Tin - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Phosphorous - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Lead - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Total impurities - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Copper - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Carbon - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Manganese - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Sulphur - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Phosphorous - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Silicon - IS 228 (optional))	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Tota Aluminium - IS 228 (optional))	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Copper - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Lead - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Total impurities - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Zinc - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Carbon - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Silicon - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Manganese - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Nickel - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Chromium - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Molybdenum - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Sulphur - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Phosphorous - IS 228)	-	0	-
3(TYPES)	-	0	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	0	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	0	-
5.2 ,Table 6(Tolerances-Tolerances on dimensions of hinges )	-	0	-
6.1(Manufacture- General)	-	0	-
6.2- Table 2,3,4,5 (Kunckles)	-	0	-
6.3(Screw Holes)	-	0	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	0	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	0	-
6.3.3 Fig-1(Position of Holes)	-	0	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	0	-
8.2(Packing -Each Package shall bear the following Particulars)	-	0	-
7(Workmanship & Finish)	-	0	-
10(Marking)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Copper - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Lead - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	0	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Zinc- IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	0	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	0	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Tin - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Phosphorous - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Lead - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Total impurities - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Copper - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Carbon - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Manganese - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Sulphur - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Phosphorous - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Silicon - IS 228 (optional))	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Tota Aluminium - IS 228 (optional))	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Copper - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Lead - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Total impurities - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Zinc - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Carbon - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Silicon - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Manganese - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Nickel - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Chromium - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Molybdenum - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Sulphur - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Phosphorous - IS 228)	-	0	-
3(TYPES)	-	0	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	0	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	0	-
5.2 ,Table 6(Tolerances-Tolerances on dimensions of hinges )	-	0	-
6.1(Manufacture- General)	-	0	-
6.2- Table 2,3,4,5 (Kunckles)	-	0	-
6.3(Screw Holes)	-	0	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	0	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	0	-
6.3.3 Fig-1(Position of Holes)	-	0	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	0	-
8.2(Packing -Each Package shall bear the following Particulars)	-	0	-
7(Workmanship & Finish)	-	0	-
10(Marking)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Copper - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Lead - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	0	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Zinc- IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	0	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	0	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Tin - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Phosphorous - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Lead - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Total impurities - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Copper - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Carbon - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Manganese - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Sulphur - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Phosphorous - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Silicon - IS 228 (optional))	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Tota Aluminium - IS 228 (optional))	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Copper - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Lead - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Total impurities - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Zinc - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Carbon - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Silicon - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Manganese - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Nickel - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Chromium - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Molybdenum - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Sulphur - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Phosphorous - IS 228)	-	0	-
3(TYPES)	-	0	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	0	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	0	-
5.2 ,Table 6(Tolerances-Tolerances on dimensions of hinges )	-	0	-
6.1(Manufacture- General)	-	0	-
6.2- Table 2,3,4,5 (Kunckles)	-	0	-
6.3(Screw Holes)	-	0	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	0	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	0	-
6.3.3 Fig-1(Position of Holes)	-	0	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	0	-
8.2(Packing -Each Package shall bear the following Particulars)	-	0	-
7(Workmanship & Finish)	-	0	-
10(Marking)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Copper - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Lead - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	0	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Zinc- IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	0	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	0	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	0	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	0	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Tin - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Phosphorous - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Lead - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Total impurities - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Copper - IS 4027:1967)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Carbon - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Manganese - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Sulphur - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Phosphorous - IS 228)	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Silicon - IS 228 (optional))	-	0	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Tota Aluminium - IS 228 (optional))	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Copper - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Lead - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Iron - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Total impurities - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Zinc - IS 3685:1966)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Carbon - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Silicon - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Manganese - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Nickel - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Chromium - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Molybdenum - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Sulphur - IS 228)	-	0	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Phosphorous - IS 228)	-	0	-
3(TYPES)	-	0	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	0	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	0	-
5.2 ,Table 6(Tolerances-Tolerances on dimensions of hinges )	-	0	-
6.1(Manufacture- General)	-	0	-
6.2- Table 2,3,4,5 (Kunckles)	-	0	-
6.3(Screw Holes)	-	0	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	0	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	0	-
6.3.3 Fig-1(Position of Holes)	-	0	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	0	-
8.2(Packing -Each Package shall bear the following Particulars)	-	0	-
7(Workmanship & Finish)	-	0	-
10(Marking)	-	0	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	-	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	-	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	-	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	-	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	-	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	-	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	-	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	-	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	-	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Copper - IS 3685:1966)	-	-	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Lead - IS 3685:1966)	-	-	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Iron - IS 3685:1966)	-	-	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	-	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Zinc- IS 3685:1966)	-	-	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	-	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	-	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	-	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	-	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	-	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	-	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	-	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	-	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	-	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	-	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	-	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	-	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Tin - IS 4027:1967)	-	-	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Phosphorous - IS 4027:1967)	-	-	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Lead - IS 4027:1967)	-	-	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Total impurities - IS 4027:1967)	-	-	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Copper - IS 4027:1967)	-	-	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Carbon - IS 228)	-	-	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Manganese - IS 228)	-	-	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Sulphur - IS 228)	-	-	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Phosphorous - IS 228)	-	-	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Silicon - IS 228 (optional))	-	-	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Tota Aluminium - IS 228 (optional))	-	-	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Copper - IS 3685:1966)	-	-	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Lead - IS 3685:1966)	-	-	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Iron - IS 3685:1966)	-	-	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Total impurities - IS 3685:1966)	-	-	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Zinc - IS 3685:1966)	-	-	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Carbon - IS 228)	-	-	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Silicon - IS 228)	-	-	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Manganese - IS 228)	-	-	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Nickel - IS 228)	-	-	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Chromium - IS 228)	-	-	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Molybdenum - IS 228)	-	-	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Sulphur - IS 228)	-	-	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Phosphorous - IS 228)	-	-	-
3(TYPES)	-	-	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	-	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	-	-
5.2 ,Table 6(Tolerances-Tolerances on dimensions of hinges )	-	-	-
6.1(Manufacture- General)	-	-	-
6.2- Table 2,3,4,5 (Kunckles)	-	-	-
6.3(Screw Holes)	-	-	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	-	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	-	-
6.3.3 Fig-1(Position of Holes)	-	-	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	-	-
8.2(Packing -Each Package shall bear the following Particulars)	-	-	-
7(Workmanship & Finish)	-	-	-
10(Marking)	-	-	-

Complete

26 Aug, 2024

140

IS 14544 (1998)

Leather safety foot wear with direct moulded polyvinyl chloride (PVC) sole - Specification

47000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Types)	-	691	-
5, 5.1(Requirements )	-	691	-
5.2, 5.2.1, 5.2.1.1(Materials - Upper Leather )	-	691	-
5.2.2(Materials - Insole Material )	-	691	-
5.2.3(Materials - Stiffener )	-	691	-
5.2.4(Materials - Lining Material )	-	691	-
5.2.5(Materials - Threads )	-	691	-
5.2.6, 5.2.6.1(Materials - Grinderies - Lasting tacks )	-	691	-
5.2.6, 5.2.6.2(Materials - Grinderies - Shanks)	-	691	-
5.2.6, 5.2.6.3(Materials - Grinderies - Eyelets)	-	691	-
5.2.7(Materials - Cotton NEWAR)	-	691	-
5.2.8(Materials - Toe-Compound)	-	691	-
5.2.9(Materials - Laces)	-	691	-
5.2.10(Materials - Steel Toe Cap)	-	691	-
5.2.11.1 (Table 1)(Sole and Heel )	-	691	-
5.2.11.2(Sole and Heel )	-	691	-
5.2.11.3 (Table 2)(Sole and Heel )	-	691	-
5.2.11.4(Sole and Heel )	-	691	-
5.3 (Table 3)(Components)	-	691	-
5.4.8(Workmanship and Finish)	-	691	-
5.4.8.2(Workmanship and Finish)	-	691	-
5.4.8.3(Workmanship and Finish)	-	691	-
5.5, 5.5.1(Mass)	-	691	-
5.5, 5.5.2(Mass)	-	691	-
5.5, 5.5.3(Mass)	-	691	-
5.6(Performance Test)	-	691	-
5.7, 5.7.1(Adhesion Test on Moulded Bottoms)	-	691	-
5.7, 5.7.2(Adhesion Test on Moulded Bottoms)	-	691	-
7, 7.1(Marking)	-	691	-
7.1.1, 7.1.2(Marking)	-	691	-
5.7(Adhesion Test )	-	691	-
5.6(Impact resistance )	-	691	-
5.5(Mass per pairs)	-	691	-
5.4(Construction)	-	691	-
5.3(Thickness of components )	-	691	-
5.2.11.4(Ageing Test)	-	691	-
5.2.11.2(Mass after resistance to chemical effect)	-	691	-
5.2.11.2(Tensile Strength after resistance to chemical effect)	-	691	-
5.2.11.2(Elongation at break after Resistance to chemical effect)	-	691	-
5.2.11.2(Hardness after Resistance to chemical effect )	-	691	-
5.2.11(Flexing Resistance )	-	691	-
5.2.11(Tensile Strength )	-	691	-
5.2.11(Elongation at break)	-	691	-
5.2.11(Hardness (IRHD))	-	691	-
5.2.11(Material Sole & heel )	-	691	-
5.2.10(Impact resistance )	-	691	-
5.2.9(Length )	-	691	-
5.2.8(Toe-compound )	-	691	-
5.2.7(Width of fabric)	-	691	-
5.2.6.3(Eyelets diameter)	-	691	-
5.2.6.2(Corrosion Shanks )	-	691	-
5.2.6.1(Corrosion test Lasting tacks)	-	691	-
5.2.5(Breaking Strength )	-	691	-
5.2.5(Twist)	-	691	-
5.2.5(Count)	-	691	-
5.2.5(Composition )	-	691	-
5.2.4(Lining Material )	-	691	-
5.2.3(Peel Strength )	-	691	-
5.2.3(Shape Retention)	-	691	-
5.2.3(Moisture)	-	691	-
5.2.3(Resilience Test)	-	691	-
5.2.3(Hardness )	-	691	-
5.2.3(Dry collapsing)	-	691	-
5.2.2(Insole Material )	-	691	-
5.2(Material )	-	691	-
4(Types)	-	-	-
5, 5.1(Requirements )	-	-	-
5.2, 5.2.1, 5.2.1.1(Materials - Upper Leather )	-	-	-
5.2.2(Materials - Insole Material )	-	-	-
5.2.3(Materials - Stiffener )	-	-	-
5.2.4(Materials - Lining Material )	-	-	-
5.2.5(Materials - Threads )	-	-	-
5.2.6, 5.2.6.1(Materials - Grinderies - Lasting tacks )	-	-	-
5.2.6, 5.2.6.2(Materials - Grinderies - Shanks)	-	-	-
5.2.6, 5.2.6.3(Materials - Grinderies - Eyelets)	-	-	-
5.2.7(Materials - Cotton NEWAR)	-	-	-
5.2.8(Materials - Toe-Compound)	-	-	-
5.2.9(Materials - Laces)	-	-	-
5.2.10(Materials - Steel Toe Cap)	-	-	-
5.2.11.1 (Table 1)(Sole and Heel )	-	-	-
5.2.11.2(Sole and Heel )	-	-	-
5.2.11.3 (Table 2)(Sole and Heel )	-	-	-
5.2.11.4(Sole and Heel )	-	-	-
5.3 (Table 3)(Components)	-	-	-
5.4.8(Workmanship and Finish)	-	-	-
5.4.8.2(Workmanship and Finish)	-	-	-
5.4.8.3(Workmanship and Finish)	-	-	-
5.5, 5.5.1(Mass)	-	-	-
5.5, 5.5.2(Mass)	-	-	-
5.5, 5.5.3(Mass)	-	-	-
5.6(Performance Test)	-	-	-
5.7, 5.7.1(Adhesion Test on Moulded Bottoms)	-	-	-
5.7, 5.7.2(Adhesion Test on Moulded Bottoms)	-	-	-
7, 7.1(Marking)	-	-	-
7.1.1, 7.1.2(Marking)	-	-	-
5.7(Adhesion Test )	-	-	-
5.6(Impact resistance )	-	-	-
5.5(Mass per pairs)	-	-	-
5.4(Construction)	-	-	-
5.3(Thickness of components )	-	-	-
5.2.11.4(Ageing Test)	-	-	-
5.2.11.2(Mass after resistance to chemical effect)	-	-	-
5.2.11.2(Tensile Strength after resistance to chemical effect)	-	-	-
5.2.11.2(Elongation at break after Resistance to chemical effect)	-	-	-
5.2.11.2(Hardness after Resistance to chemical effect )	-	-	-
5.2.11(Flexing Resistance )	-	-	-
5.2.11(Tensile Strength )	-	-	-
5.2.11(Elongation at break)	-	-	-
5.2.11(Hardness (IRHD))	-	-	-
5.2.11(Material Sole & heel )	-	-	-
5.2.10(Impact resistance )	-	-	-
5.2.9(Length )	-	-	-
5.2.8(Toe-compound )	-	-	-
5.2.7(Width of fabric)	-	-	-
5.2.6.3(Eyelets diameter)	-	-	-
5.2.6.2(Corrosion Shanks )	-	-	-
5.2.6.1(Corrosion test Lasting tacks)	-	-	-
5.2.5(Breaking Strength )	-	-	-
5.2.5(Twist)	-	-	-
5.2.5(Count)	-	-	-
5.2.5(Composition )	-	-	-
5.2.4(Lining Material )	-	-	-
5.2.3(Peel Strength )	-	-	-
5.2.3(Shape Retention)	-	-	-
5.2.3(Moisture)	-	-	-
5.2.3(Resilience Test)	-	-	-
5.2.3(Hardness )	-	-	-
5.2.3(Dry collapsing)	-	-	-
5.2.2(Insole Material )	-	-	-
5.2(Material )	-	-	-

Complete

26 Aug, 2024

141

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

66056 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(SAMPLING AND CONDITIONING)	-	419	-
5(DESIGN)	-	419	-
6(SIZE AND FITTINGS)	-	419	-
7.1.1(Whole Footwear)	-	419	-
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	419	-
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	419	-
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	419	-
7.1.5(Energy Absorption at Seat Region)	-	419	-
7.1.6(Complete Shoe Flexing)	-	419	-
7.1.7(Washability)	-	419	-
7.1.8(Slip Resistance)	-	419	-
7.1.9(Heel Drop)	-	419	-
7.2 , Table No. 2 , i)(Flexing resistance)	-	419	-
7.2 , Table No. 2 , ii)(Tear strength (average force))	-	419	-
7.2 , Table No. 2 , iii)("Colour fastness rubbing (To and fro) Grey scale rate Dry: (rubbing) Rating: (Marring and staining) ")	-	419	-
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	419	-
7.2 , Table No. 2 , iv) ,b)(Water vapour coefficient)	-	419	-
7.2 , Table No. 2 , v)(Stitch tear strength (double hole))	-	419	-
7.2 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Rating: (Marring)")	-	419	-
7.2 , Table No. 2 , vii)(Tensile strength)	-	419	-
7.2 , Table No. 2 , viii)(Elongation at break,)	-	419	-
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	419	-
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	419	-
7.2 , Table No. 3 , i)(Breaking strength "As per Method 1 of IS 7016 (Part 2)/ ISO 1421 : 2016 or ISO 17706")	-	419	-
7.2 , Table No. 3 , ii)(Elongation at break)	-	419	-
7.2 , Table No. 3 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	419	-
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	419	-
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	419	-
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	419	-
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	419	-
7.2 , Table No. 3 , vi)(Hydrolysis resistance)	-	419	-
7.2 , Table No. 3 , vii)(Colour fastness to light grey scale rate)	-	419	-
7.2 , Table No. 3 , viii)(Bursting Strength,)	-	419	-
7.3 , Table No. 4 , i)(Tear strength,)	-	419	-
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	419	-
7.3 , Table No. 4 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, ")	-	419	-
7.3 , Table No. 4 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, ")	-	419	-
7.4 , Table No. 5 , i)(Thickness)	-	419	-
7.4 , Table No. 5 , ii)(Flexing index)	-	419	-
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	419	-
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	419	-
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	419	-
7.5 , Table No. 6 , i)(Thickness)	-	419	-
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	419	-
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	419	-
7.5 , Table No. 6 , iii) , b)(Water Desorption)	-	419	-
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	419	-
7.6 , Table No. 7 , i)(Abrasion resistance (volume loss))	-	419	-
7.6 , Table No. 7 , ii)(Flexing resistance)	-	419	-
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	419	-
7.6 , Table No. 7 , iv)(Tear strength)	-	419	-
7.6 , Table No. 7 , v)(Tensile strength)	-	419	-
7.6 , Table No. 7 , vi)(Elongation at break)	-	419	-
7.6 , Table No. 7 , vii)(Compression set)	-	419	-
7.7 , Table No. 8 , i)(Compression set)	-	419	-
7.7 , Table No. 8 , ii)(Split tear strength,)	-	419	-
7.7 , Table No. 8 , iii)(Heat shrinkage,)	-	419	-
7.7 , Table No. 8 , iv)(Elongation at break,)	-	419	-
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	419	-
7.8 , Table No. 9 , ii)(Resilience)	-	419	-
7.8 , Table No. 9 , iii)(Moisture resistance)	-	419	-
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	419	-
7.8 , Table No. 9 , iv) , b)(Area shape retention after 10th collapse, dry)	-	419	-
7.8 , Table No. 9 , v)(Peel strength)	-	419	-
7.9 , Table No. 10 , i)(Peel strength)	-	419	-
7.9 , Table No. 10 , ii)(Shear strength)	-	419	-
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	419	-
7.10 , Table No. 11 , ii)(Needle strength,)	-	419	-
7.11 , Table No. 12 , i)(Breaking strength of lace,)	-	419	-
7.11 , Table No. 12 , ii)(Lace tag strength,)	-	419	-
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	419	-
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	419	-
7.11 , Table No. 12 , v)(Strength of Buckle/Ski hook)	-	419	-
7.11 , Table No. 12 , vi)(Corrosion resistance)	-	419	-
7.12("Chemical Requirement on Complete Product for All Types of Sports Shoe")	-	2307	-
8(MARKING AND PACKING)	-	419	-
7.12, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	2307	-
7.12, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2307	-
7.12, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2307	-
7.12, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	2307	-
7.12, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	2307	-
7.12, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	2307	-
7.12, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	2307	-
7.12, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	2307	-
7.12, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	2307	-
7.12, Table no. 1 of IS 17011,(x)(pH)	-	2307	-
7.12, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	2307	-
7.12, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	2307	-

Complete

26 Aug, 2024

142

IS 5557 (2004)

Industrial and protective rubber knee and ankle boots - Specification (Fourth Revision)

19000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	345	-
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	345	-
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	345	-
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	345	-
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	345	-
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	345	-
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	345	-
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	345	-
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	345	-
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	345	-
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	345	-
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	345	-
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	345	-
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	345	-
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	345	-
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	345	-
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	345	-
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	345	-
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	345	-
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	345	-
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	345	-
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	345	-
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	345	-
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	345	-
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	345	-
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	345	-
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	345	-
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	345	-
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	345	-
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	345	-
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	345	-
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	345	-
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	345	-
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	345	-
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	345	-
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	345	-
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	345	-
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	345	-
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	345	-
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	345	-
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	345	-
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	345	-
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	345	-
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	345	-
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	345	-
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	345	-
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	345	-
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	345	-
5, 5.1(Requirement)	-	345	-
6.1(Marking)	-	345	-
6, 6.1(Packing)	-	345	-
5, 5.1(Requirement)	-	345	-
6.1(Marking)	-	345	-
6.2(Packing)	-	345	-

Complete

26 Aug, 2024

143

IS 16645 (2018)

Moulded Plastics Footwear ” Lined or Unlined Polyurethane Boots for General Industrial use ” Specification

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.8.2& 5.8.3(Hydrolysis )	-	576	-
5.8.1(Tensile strength after Hydrolysis)	-	576	-
5.7(Split tear strength )	-	576	-
5.6(Resistance to soling to cut growth)	-	576	-
5.5(Cold flex temp of upper)	-	576	-
5.4(Hardness (IRHD))	-	576	-
5.3(Tesile Strength )	-	576	-
5.2(Resistance to flexing of boot upper)	-	576	-
5.1(General )	-	576	-
4.3(Thickness of components )	-	576	-
4.2(Thickness )	-	576	-
4.1(Soling Pattern )	-	576	-

Complete

26 Aug, 2024

144

IS 16994 (2018)

Footwear for Men and Women for Municipal Scavenging Work

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.6(Leak Proof test)	-	256	-
8.4(Volatility & lead content )	-	256	-
8.3(Compression Resistance)	-	256	-
8.3(Impact resistance )	-	256	-
8.2(Internal Toe cap length)	-	256	-
8.1(Height of upper )	-	256	-
8.0(Construction)	-	256	-
7.10(Ageing test)	-	256	-
7.9(Hydrolysis)	-	256	-
7.8(Insocks Material )	-	256	-
7.7.5(Upper / Outsole bond strength)	-	256	-
7.7.4(Interlayer Bond Strength )	-	256	-
7.7.3(Flexing Resistance )	-	256	-
7.7.2(Abrasion Resistance)	-	256	-
7.7.1(Tear Strength )	-	256	-
7.7(Hardness (IRHD))	-	256	-
7.7(Thickness)	-	256	-
7.7(Density )	-	256	-
7.6(Peel Strength )	-	256	-
7.6(Shape retention)	-	256	-
7.6(Moisture )	-	256	-
7.6(Resilience test )	-	256	-
7.6(Hardness)	-	256	-
7.6(Dry collapsing)	-	256	-
7.5(Insocks )	-	256	-
7.5(Insoles )	-	256	-
7.5(Water abrasion & desorption)	-	256	-
7.5(Thickness )	-	256	-
7.4(Tensile Strength )	-	256	-
7.4(Abrasion Resistance)	-	256	-
7.4(Tear Strength )	-	256	-
7.3(Flexing Resistance )	-	256	-
7.3(Tensile Strength )	-	256	-
7.3(Thickness )	-	256	-
7.3(Water Vapour permeability & coefficient )	-	256	-
7.3(Tear Strength )	-	256	-
7.1(Compression Tester)	-	256	-
7.1(Impact resistance )	-	256	-

Complete

26 Aug, 2024

145

IS 17012 (2018)

High ankle tactical boots with pu - Rubber sole - Specification

48500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Innocuousness Test IS 17011)	-	30000	-
4.16.2(Breaking Strength of lace )	-	349	-
4.16.1(Length of lace )	-	349	-
4.15(D-ring & Hooks )	-	349	-
6.1(Resistance to Fuel Oil)	-	349	-
4.14.9(Resistance to hot contact )	-	349	-
4.14.8(Flexing resistance )	-	349	-
4.14.7(Ageing test)	-	349	-
4.14.6(Hardness (IRHD))	-	349	-
4.14.5(Abrasion resistance )	-	349	-
4.14.4(Tear Strength)	-	349	-
4.14.3(Sole Density )	-	349	-
4.14.2(Thickness)	-	349	-
4.14.1(Meterial)	-	349	-
4.13(Breaking Strength of thread )	-	349	-
4.12.2(Tear Strength)	-	349	-
4.12.1(Thickness )	-	349	-
4.11.2(Tear Strength)	-	349	-
4.11.1(Thickness )	-	349	-
4.10.3(Water absorption & desorption percent)	-	349	-
4.10.2(Abrasion resistance )	-	349	-
4.10.1(Meterial )	-	349	-
4.9.3(Water absorption & desorption percent)	-	349	-
4.9.2(Abrasion resistance )	-	349	-
4.9.1(Thickness)	-	349	-
4.8(Thickness Toe puff & counter stiffener)	-	349	-
4.7.5(Water Vapour permeability & coefficient )	-	349	-
4.7.4(Abrasion resistance )	-	349	-
4.7.3(Tear Strength)	-	349	-
4.7.2(Meterial Counter & Toungue)	-	349	-
4.7.1(Meterial vamp & Quarter)	-	349	-
4.6.3(Water Penetration and water absorption )	-	349	-
4.6.2(Tear Strength)	-	349	-
4.6.1(Thickness )	-	349	-
4.5.8(Energy absorption of seat region )	-	349	-
4.5.7(Cold Insulation of sole complex)	-	349	-
4.5.6(Heat Insulation of sole Complex)	-	349	-
4.5.5(Antistatic test)	-	349	-
4.5.4(Slip Resitance)	-	349	-
4.5.3.2(Interayer bond strength)	-	349	-
4.5.3.1(Upper/outsole bond strength)	-	349	-
4.5.2(Ergonomic Feature)	-	349	-
4.5.1(Contruction)	-	349	-
4.4(Height of upper )	-	349	-
4.3.2(Weight)	-	349	-
4.3.1(Size)	-	349	-
4.2(Design )	-	349	-
Cl. 6, Cl.6.1, 6.1.1 & 6.1.2, 8.6 of IS 15298 part 1,ISO 1817,ISO 4643,(Resistance to fuel oil)	-	349	-
8, 8.1, 8.2, 8.2.1(Marking)	-	349	-
9(Information to be Supplied)	-	349	-
Cl.4.6.4(Water Penetration and Water Absorption)	-	349	-
Cl. 6, Cl.6.1, 6.1.1 & 6.1.2,(Resistance to fuel oil)	-	349	-
CL.8,8.1, 8.2,8.2.1(Marking)	-	349	-
Cl.9,(Information to be Supplied)	-	349	-

Complete

26 Aug, 2024

146

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	360	-
5/5.1(REQUIREMENTS-General)	-	360	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	360	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	360	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	360	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	360	-
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	360	-
5/5.1(REQUIREMENTS-General)	-	360	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	360	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	360	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	360	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	360	-
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	360	-
5/5.1(REQUIREMENTS-General)	-	360	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	360	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	360	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	360	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	360	-
6(Marking and packing)	-	360	-
8.1(Test methods)	-	360	-
8.3(Measurement of thickness)	-	360	-
Cl.6.1,6.2,6.3(Marking and packing)	-	360	-
8.1(Test Methods)	-	360	-
Cl.8.3(Measurement of thickness ")	-	360	-

Complete

26 Aug, 2024

147

IS 13995 (1995)

Unlined moulded rubber boots - Specification

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.7(Size)	-	777	-
5.1.6(Design)	-	777	-
5.1.5(Flexing resistance of upper)	-	777	-
5.1.3(Tear Strength)	-	777	-
5.1.2(Tensile Strength (after ageing))	-	777	-
5.1.1(Tensile Strength (before ageing))	-	777	-
4.1(Thickness )	-	777	-
6, 6.1(Marking)	-	777	-

Complete

26 Aug, 2024

148

IS 5557 : Part 2 (2018)

All rubber gum boots and ankle boots: Part 2 occupational purposes

49000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(VISUAL)	-	465	-
3.2(specificgravity)	-	431	-
3.3(specificgravity)	-	431	-
3.4(specificgravity)	-	431	-
3.5(visual)	-	431	-
3.6(VISUAL)	-	431	-
3.7(VISUAL)	-	431	-
4(visual)	-	431	-
5(visual)	-	431	-
6(visual)	-	431	-
7.1(visual)	-	431	-
7.1.1(Tear strength)	-	431	-
7.1.2(Abrasion resistance)	-	431	-
7.2(all test of table 1)	-	431	-
7.3(all test of table 2)	-	431	-
7.4(Visual)	-	431	-
7.4.1(all test of table 3)	-	431	-
7.5(Visual)	-	431	-
7.5.1(Tensile)	-	431	-
7.5.2(Thickness)	-	431	-
7.5.3(Upper flexing)	-	431	-
7.6(VISUAL)	-	431	-
7.6.1(Out sole thickness)	-	431	-
7.6.2(out sole tear strength)	-	431	-
7.6.3(out sole abrasion)	-	431	-
7.6.4(out sole flexing)	-	431	-
7.6.5(Interlayer bond strength)	-	431	-
7.7(INSOCK Visual)	-	431	-
7.7.1(Insock thickness)	-	431	-
7.7.2(Insock abrasion)	-	431	-
8(CONSTRUCTION)	-	431	-
8.1(Hot contact)	-	431	-
8.2(Leak proofness)	-	431	-
8.3(Height of upper)	-	431	-
8.4(Adhesion test)	-	431	-
8.5(Resistance to acid & alkaline)	-	431	-
8.7.1(Antistatic)	-	431	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	431	-
8.7.3(Elecrically nsulating footwear)	-	431	-
8.7.4(Resistance to cold)	-	431	-
9.1(ALLERIGIC DISPERSE DYES)	-	10000	-
9.2(Carcinogenic Disperse dyes)	-	10000	-
9.3(Phthalate)	-	10000	-
10(Visual OBSERVATION)	-	431	-
11.1(Visual OBSERVATION)	-	431	-
11.2(Visual OBSERVATION)	-	431	-
11.3(Visual OBSERVATION)	-	431	-

Complete

26 Aug, 2024

149

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

50500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	265	-
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	134	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	134	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	134	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	134	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	134	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	134	-
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	134	-
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	134	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	134	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	134	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	134	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	134	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	134	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	134	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	134	-
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	134	-
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	134	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	134	-
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	134	-
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	134	-
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	134	-
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	134	-
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	134	-
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	134	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	134	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	134	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	134	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	134	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	134	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	134	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	134	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	134	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	134	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	134	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	134	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	134	-
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	134	-
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	134	-
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	134	-
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	134	-
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	134	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	134	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	134	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	134	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	134	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	134	-
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	134	-
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	134	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	134	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	134	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	134	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	134	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	134	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	134	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	134	-
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	134	-
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	134	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	134	-
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	134	-
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	134	-
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	134	-
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	134	-
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	134	-
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	134	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	134	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	134	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	134	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	134	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	134	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	134	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	134	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	134	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	134	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	134	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	134	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	134	-
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	134	-
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	134	-
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	134	-
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	134	-
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	134	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	134	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	134	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	134	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	134	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	134	-
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	134	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	134	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	134	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	134	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	134	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	134	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	134	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	134	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	134	-
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	134	-
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	134	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	134	-
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	134	-
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	134	-
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	134	-
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	134	-
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	134	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	134	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	134	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	134	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	134	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	134	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	134	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	134	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	134	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	134	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	134	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	134	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	134	-
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	134	-
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	134	-
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	134	-
4(Types)	-	134	-
5(Requirements)	-	134	-
5.1(Design)	-	134	-
5.2.4(Reinforcing Material)	-	134	-
5.2.8.4(Colour of the lace)	-	134	-
5.3, 5.3.1,5.3.3,5.3.4(Construction)	-	134	-
5.10(Consolidation Test IS 3400 (Part 5) : 1986)	-	134	-
8(CHEMICAL REQUIREMENTS)	-	15000	-
9, 9.1(BIS CERTIFICATION MARKING)	-	134	-
10(Marking)	-	134	-
11(Packing)	-	134	-
Cl. 5.2.4(Reinforcing Material)	-	134	-
Cl. 5.2.8.4(Colour of the lace)	-	134	-
11(PACKING)	-	134	-
Cl. 5.3(Construction 5.3.1,5.3.3,5.3.4)	-	134	-
10(Marking)	-	134	-
7.1(Resistance to fuel)	-	134	-
7.2(Resistance to electricity)	-	134	-
9, 9.1(BIS CERTIFICATION MARKING)	-	268	-
Cl. 8(CHEMICAL REQUIREMENTS)	-	15000	-

Complete

26 Aug, 2024

150

IS 2080 (2021)

Specification for stabilized hydrogen peroxide First Revision

8750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description - IS 2080:2021)	-	0	-
4.2(Strength - IS 2080:2021)	-	1750	-
4.3(Stability - IS 2080:2021)	-	1500	-
4.4/Table 1 (i)(Acidity (as H2SO4) - IS 2080:2021)	-	750	-
4.4/Table 1 (ii)(Residue on Evaporation - IS 2080:2021)	-	1000	-
4.4/Table 1 (iii)(Residue on Ignition - IS 2080:2021)	-	750	-
4.4/Table 1 (iv)(Iron (as Fe) - IS 2080:2021)	-	500	-
4.4/Table 1 (v)(Copper (as Cu) - IS 2080:2021)	-	500	-
4.4/Table 1 (vi)(Lead (as Pb) - IS 2080:2021)	-	500	-
4.4/Table 1 (vii)(Arsenic (as As2O3) - IS 2080:2021)	-	500	-
5.1(Packing)	-	0	-
5.2(Marking)	-	0	-
4.1(Description - IS 2080:2021)	-	0	-
4.2(Strength - IS 2080:2021)	-	1750	-
4.3(Stability - IS 2080:2021)	-	1500	-
4.4/Table 1 (i)(Acidity (as H2SO4) - IS 2080:2021)	-	750	-
4.4/Table 1 (ii)(Residue on Evaporation - IS 2080:2021)	-	1000	-
4.4/Table 1 (iii)(Residue on Ignition - IS 2080:2021)	-	750	-
4.4/Table 1 (iv)(Iron (as Fe) - IS 2080:2021)	-	500	-
4.4/Table 1 (v)(Copper (as Cu) - IS 2080:2021)	-	500	-
4.4/Table 1 (vi)(Lead (as Pb) - IS 2080:2021)	-	500	-
4.4/Table 1 (vii)(Arsenic (as As2O3) - IS 2080:2021)	-	500	-
5.1(Packing)	-	0	-
5.2(Marking)	-	0	-

Complete

26 Aug, 2024

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

ALPHA TEST HOUSE PRIVATE LIMITED

198-199, M.I.E, PHASE-I, BAHADURGARH, HARYANA-124507, Bahadurgarh, Jhajjar, Haryana, 124507

9711227171 info@alphatesthouse.com

Scope List