BIS - LIMS (Laboratory Information Management System)

Hindustaan Testing Solutions LLP, Ambala

Plot No. 36,Sector 1, HSIIDC IGC Saha, Ambala Cantt, Ambala Cantt, Ambala, Haryana, 133104

9355002828 hindustaantesthouse@gmail.com

Scope List

Reset

64 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2046 (1995)

Decorative thermosetting synthetic resinbonded laminated sheets specification (Second Revision)

All

25400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 , Table 1(CLASSIFICATION)	-	0	Complete Testing Charges-25400 20% discount to BIS GST applicable as per govt rule
5.1(Colour and Pattern)	-	100	-
5.2(Surface Finish)	-	100	-
5.2.2(Reverse side/Bonding)	-	0	-
5.3 ,Table 5(Thickness)	-	200	-
5.4(Appearance )	-	100	-
5.2.2(Sports, dirt and similar surface defects)	-	200	-
5.2.2(Fibres,hairs,scratches)	-	100	-
5.2.2(Accumulated(Combination)of surface defects)	-	100	-
5.2.2(Edge Defects)	-	100	-
5.2.2(Broken Corners )	-	100	-
5.4.4(Sanding Defects)	-	100	-
5.4.5 table 6(W arping (Flatness ))	-	200	-
5.4.6 (Length and width of a full size Laminate)	-	400	-
5.4.6 (Length and width of a full size Laminate)	-	0	-
5.4.7,Fig. 2(Staightness of Edges)	-	200	-
5.4.8, Fig.3(Squareness of the Laminates)	-	200	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	1500	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	2000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	1500	-
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	1800	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	1800	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	1000	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	1500	-
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	600	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	600	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	600	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	3500	-
5.5, Tables 7, Sr No.(x) Annex -O (alternative)(Resistance to colour change)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	600	-
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	1000	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	1000	-
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	600	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	600	-
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	1000	-
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	500	-
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	500	-
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	1000	-
7.2 a)(Marking)	-	0	-
7.2 b)(Marking)	-	0	-
7.2 c)(Marking)	-	0	-
7.2 d)(Marking)	-	0	-
7.2.1(Marking)	-	0	-
5 & 5.1(Colour & Pattern)	-	0	-
5.2(Surface & Finish)	-	0	-
5.2.2(Reverse side Bonding)	-	0	-
5.3(Nominal thickness)	-	0	-
5.4.1.1(Surface defects)	-	0	-
5.4.1.2(Fiber hair scratches)	-	0	-
5.4.1.3(Accumulated(combinations) of surface defect)	-	0	-
5.4.2(Edge defect)	-	0	-
5.4.3(Broken corner)	-	0	-
5.4.4(Sanding defect)	-	0	-
5.4.5(Warping(Flatness))	-	0	-
5.4.6(Length)	-	0	-
5.4.6(Width)	-	0	-
5.4.7(Straightness of edge)	-	0	-
5.4.8(Squreness of laminate)	-	0	-
5.5Table-7(1(Surfacewear)	-	0	-
Table-7(2(Immesion in boiling water)	-	0	-
Table-7(3(Dry heat resistance)	-	0	-
Table-7(4(Dimensional stability)	-	0	-
Table-7(6(Impact by small dia.Ball)	-	0	-
Table-7(7(Impact by large dia.Ball)	-	0	-
Table-7(8(Cracking resistance)	-	0	-
Table-7(9(Scracting resistance)	-	0	-
Table-7(10(Staining resistance)	-	0	-
Table-7(10(Colour change(Xenon arc resis))	-	0	-
Table-7(11(Cigarette burn resistance)	-	0	-
Table-7(12(Formability)	-	0	-
Table-7(13(Blistering)	-	0	-
Table-7(14(Steam resistance)	-	0	-
Table-7(15(Crazing reistance)	-	0	-
Table-7(16(Moisture reistance)	-	0	-
Table-8(17(Flexural Modulus)	-	0	-
Table-8(18(Flexural strength)	-	0	-
Table-8(19(Tensile strength)	-	0	-
4 , Table 1(CLASSIFICATION)	-	0	-
5.1(Colour and Pattern)	-	0	-
5.2(Surface Finish)	-	0	-
5.2.2(Reverse side/Bonding)	-	0	-
5.3 ,Table 5(Thickness)	-	0	-
5.4(Appearance )	-	0	-
5.2.2(Sports, dirt and similar surface defects)	-	0	-
5.2.2(Fibres,hairs,scratches)	-	0	-
5.2.2(Accumulated(Combination)of surface defects)	-	0	-
5.2.2(Edge Defects)	-	0	-
5.2.2(Broken Corners )	-	0	-
5.4.4(Sanding Defects)	-	0	-
5.4.5 table 6(W arping (Flatness ))	-	0	-
5.4.6 (Length and width of a full size Laminate)	-	0	-
5.4.6 (Length and width of a full size Laminate)	-	0	-
5.4.7,Fig. 2(Staightness of Edges)	-	0	-
5.4.8, Fig.3(Squareness of the Laminates)	-	0	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	0	-
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	0	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	0	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	0	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	0	-
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	0	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	0	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	0	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	0	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	0	-
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	0	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	0	-
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	0	-
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	0	-
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	0	-
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	0	-
7.2 a)(Marking)	-	0	-
7.2 b)(Marking)	-	0	-
7.2 c)(Marking)	-	0	-
7.2 d)(Marking)	-	0	-
7.2.1(Marking)	-	0	-
5 & 5.1(Colour & Pattern)	-	0	-
5.2(Surface & Finish)	-	0	-
5.2.2(Reverse side Bonding)	-	0	-
5.3(Nominal thickness)	-	0	-
5.4.1.1(Surface defects)	-	0	-
5.4.1.2(Fiber hair scratches)	-	0	-
5.4.1.3(Accumulated(combinations) of surface defect)	-	0	-
5.4.2(Edge defect)	-	0	-
5.4.3(Broken corner)	-	0	-
5.4.4(Sanding defect)	-	0	-
5.4.5(Warping(Flatness))	-	0	-
5.4.6(Length)	-	0	-
5.4.6(Width)	-	0	-
5.4.7(Straightness of edge)	-	0	-
5.4.8(Squreness of laminate)	-	0	-
5.5Table-7(1(Surfacewear)	-	0	-
Table-7(2(Immesion in boiling water)	-	0	-
Table-7(3(Dry heat resistance)	-	0	-
Table-7(4(Dimensional stability)	-	0	-
Table-7(6(Impact by small dia.Ball)	-	0	-
Table-7(7(Impact by large dia.Ball)	-	0	-
Table-7(8(Cracking resistance)	-	0	-
Table-7(9(Scracting resistance)	-	0	-
Table-7(10(Staining resistance)	-	0	-
Table-7(10(Colour change(Xenon arc resis))	-	0	-
Table-7(11(Cigarette burn resistance)	-	0	-
Table-7(12(Formability)	-	0	-
Table-7(13(Blistering)	-	0	-
Table-7(14(Steam resistance)	-	0	-
Table-7(15(Crazing reistance)	-	0	-
Table-7(16(Moisture reistance)	-	0	-
Table-8(17(Flexural Modulus)	-	0	-
Table-8(18(Flexural strength)	-	0	-
Table-8(19(Tensile strength)	-	0	-
4 , Table 1(CLASSIFICATION)	-	0	-
5.1(Colour and Pattern)	-	0	-
5.2(Surface Finish)	-	0	-
5.2.2(Reverse side/Bonding)	-	0	-
5.3 ,Table 5(Thickness)	-	0	-
5.4(Appearance )	-	0	-
5.2.2(Sports, dirt and similar surface defects)	-	0	-
5.2.2(Fibres,hairs,scratches)	-	0	-
5.2.2(Accumulated(Combination)of surface defects)	-	0	-
5.2.2(Edge Defects)	-	0	-
5.2.2(Broken Corners )	-	0	-
5.4.4(Sanding Defects)	-	0	-
5.4.5 table 6(W arping (Flatness ))	-	0	-
5.4.6 (Length and width of a full size Laminate)	-	0	-
5.4.6 (Length and width of a full size Laminate)	-	0	-
5.4.7,Fig. 2(Staightness of Edges)	-	0	-
5.4.8, Fig.3(Squareness of the Laminates)	-	0	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	0	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	0	-
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	0	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	0	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	0	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	0	-
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	0	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	0	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	0	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	0	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	0	-
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	0	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	0	-
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	0	-
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	0	-
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	0	-
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	0	-
7.2 a)(Marking)	-	0	-
7.2 b)(Marking)	-	0	-
7.2 c)(Marking)	-	0	-
7.2 d)(Marking)	-	0	-
7.2.1(Marking)	-	0	-
5 & 5.1(Colour & Pattern)	-	0	-
5.2(Surface & Finish)	-	0	-
5.2.2(Reverse side Bonding)	-	0	-
5.3(Nominal thickness)	-	0	-
5.4.1.1(Surface defects)	-	0	-
5.4.1.2(Fiber hair scratches)	-	0	-
5.4.1.3(Accumulated(combinations) of surface defect)	-	0	-
5.4.2(Edge defect)	-	0	-
5.4.3(Broken corner)	-	0	-
5.4.4(Sanding defect)	-	0	-
5.4.5(Warping(Flatness))	-	0	-
5.4.6(Length)	-	0	-
5.4.6(Width)	-	0	-
5.4.7(Straightness of edge)	-	0	-
5.4.8(Squreness of laminate)	-	0	-
5.5Table-7(1(Surfacewear)	-	0	-
Table-7(2(Immesion in boiling water)	-	0	-
Table-7(3(Dry heat resistance)	-	0	-
Table-7(4(Dimensional stability)	-	0	-
Table-7(6(Impact by small dia.Ball)	-	0	-
Table-7(7(Impact by large dia.Ball)	-	0	-
Table-7(8(Cracking resistance)	-	0	-
Table-7(9(Scracting resistance)	-	0	-
Table-7(10(Staining resistance)	-	0	-
Table-7(10(Colour change(Xenon arc resis))	-	0	-
Table-7(11(Cigarette burn resistance)	-	0	-
Table-7(12(Formability)	-	0	-
Table-7(13(Blistering)	-	0.01	-
Table-7(14(Steam resistance)	-	0	-
Table-7(15(Crazing reistance)	-	0	-
Table-7(16(Moisture reistance)	-	0	-
Table-8(17(Flexural Modulus)	-	0.01	-
Table-8(18(Flexural strength)	-	0	-
Table-8(19(Tensile strength)	-	0	-

12 Sep, 2028

-
Included w.e.f 27.11.2024 Exclusion Cl 5.5, Tables 7, (xi) (Resistance to Cigarette burns) Cl 5.5, Tables 7, (xiv) (Formability Method B) Cl 5.5, Tables 7, (xiv) (Resistance to Blistering Method B)

IS 14315 (1995)

Commercial Veneers -specification

Type A & B

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 (i)(Discolouration)	-	100	-
4 (ii)(Dote)	-	50	-
4 (iii)(Insect Hole)	-	50	-
4 (iv)(Joints)	-	50	-
4 (v)(Knots (dead))	-	50	-
4 (vi)(Pin Knots (dead))	-	50	-
4 (vii)(Pin Knots (live))	-	50	-
4 (viii)(Knots (tight))	-	50	-
4 (ix)(Patches)	-	50	-
4 (x)(Splits)	-	100	-
4 (xi)(Swirl)	-	100	-
5(Manufacture)	-	0	-
6(Face Veneer)	-	50	-
7(Core and Crossband veneer)	-	50	-
8(Joints in veneers)	-	50	-
9.2(Dimension)	-	200	-
9.3(Thickness)	-	150	-
9.4.1 (Tolerances)	-	100	-
9.4.2(Squarenes)	-	100	-
9.4.3(Edge Straightness)	-	100	Face Veneer-1500, Core/Cross band-1500 GSTIN as per govt rule 20% discount to BIS
11(Marking)	-	0	-
4 (i)(Discolouration)	-	0	-
4 (ii)(Dote)	-	0	-
4 (iii)(Insect Hole)	-	0	-
4 (iv)(Joints)	-	0	-
4 (v)(Knots (dead))	-	0	-
4 (vi)(Pin Knots (dead))	-	0	-
4 (vii)(Pin Knots (live))	-	0	-
4 (viii)(Knots (tight))	-	0	-
4 (ix)(Patches)	-	0	-
4 (x)(Splits)	-	0	-
4 (xi)(Swirl)	-	0	-
5(Manufacture)	-	0	-
6(Face Veneer)	-	0	-
7(Core and Crossband veneer)	-	0	-
8(Joints in veneers)	-	0	-
9.2(Dimension)	-	0	-
9.3(Thickness)	-	0	-
9.4.1 (Tolerances)	-	0	-
9.4.2(Squarenes)	-	0	-
9.4.3(Edge Straightness)	-	0	-
11(Marking)	-	0	-

12 Sep, 2028

-
Included w.e.f. 16.01.2024

IS 3097 (2006)

Veneered Particle Boards -Specification

All

38500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No - 3(TERMINOLOGY)	-	0	-
Clause No - 4(GRADES AND TYPES)	-	0	-
Clause No - 5.1(Particle Board)	-	14700	Grade 1-14700, Grade 2-11700
Clause No - 5.2.1.1("Timbers for face veneers of decorative type veneered particle boards")	-	0	-
Clause No - 5.2.1.1(a)("particle boards, shall be of Type A or Type B surface ")	-	0	-
Clause No - 5.3(Adhesive)	-	8000	MR grade-7200 & BWR & BWP-8000
Clause No - 6.1(Preservative Treatment of Veneers)	-	0	-
Clause No - 6.2.7(Lipping)	-	0	-
Clause No - 7(Dimensional Tolerance)	-	800	-
Clause No - 9.1 (1(cutting the test specimens)	-	0	-
Clause No - 9.1 (2(" method of preparation and conditioning oftest specimens")	-	0	-
Clause No - 9.1 (a(Determination of density)	-	800	-
Clause No - 9.1 (b(Determination of moisture content)	-	800	-
Clause No - 9.1 (c(Water absorption)	-	1500	-
Clause No - 9.1 (e) (1(Determination of swelling in water - Swelling due to general absorption)	-	2000	-
Clause No - 9.1 (e) (2(Determination of swelling in water -Swelling due to surface absorption)	-	2000	-
Clause No - 9.1 (g)("Modulus of rupture (MOR) and modulus of elasticity (MOE) ")	-	1500	-
Clause No - 9.1 (h)("Determination of deflection under sustained load (long time loading test)")	-	1000	-
Clause No - 11(MARKING)	-	0	-
Clause No - 3(TERMINOLOGY)	-	0	-
Clause No - 4(GRADES AND TYPES)	-	0	-
Clause No - 5.1(Particle Board)	-	0	-
Clause No - 5.2.1.1("Timbers for face veneers of decorative type veneered particle boards")	-	0	-
Clause No - 5.2.1.1(a)("particle boards, shall be of Type A or Type B surface ")	-	0	-
Clause No - 5.3(Adhesive)	-	0	-
Clause No - 6.1(Preservative Treatment of Veneers)	-	0	-
Clause No - 6.2.7(Lipping)	-	0	-
Clause No - 7(Dimensional Tolerance)	-	0	-
Clause No - 9.1 (1(cutting the test specimens)	-	0	-
Clause No - 9.1 (2(" method of preparation and conditioning oftest specimens")	-	0	-
Clause No - 9.1 (a(Determination of density)	-	0	-
Clause No - 9.1 (b(Determination of moisture content)	-	0	-
Clause No - 9.1 (c(Water absorption)	-	0	-
Clause No - 9.1 (e) (1(Determination of swelling in water - Swelling due to general absorption)	-	0	-
Clause No - 9.1 (e) (2(Determination of swelling in water -Swelling due to surface absorption)	-	0	-
Clause No - 9.1 (g)("Modulus of rupture (MOR) and modulus of elasticity (MOE) ")	-	0	-
Clause No - 9.1 (h)("Determination of deflection under sustained load (long time loading test)")	-	0	-
Clause No - 11(MARKING)	-	0	-
Clause 9.1 d) Water Resistance test(Clause 9.1 d) Water Resistance test)	-	1500	-
9.1 f)Adhesion of plies(9.1 f)Adhesion of plies)	-	500	Testing charges-38500 (Separate testing charges- IS 3097-15800, Particle board-Grade 14700 & Grade 2-11700, Adhesive-MR-7200 & BWR & BWP-8000) 20% Discount to BIS GSTIN as per govt rule

12 Sep, 2028

-
Included w.e.f. 16.01.2024

IS 15786 (2008)

Prelaminated cement bonded particle board - Specification

All

32900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 10.3 (Moisture content)	-	600	-
Clause 10.3 (Moisture content)	-	0	-
Clause 10.3 (Moisture content)	-	0	-
5.1(Cement Bonded Particle Board)	-	14400	-
5.2(Impregnated Base Paper)	-	1000	-
5.3(Impregnated OverlaylUnderIay)	-	1000	-
5.4(Finished Foil)	-	1000	-
6(Manufacture)	-	0	-
7(Finish)	-	0	-
8(DIMENSIONS AND TOLERANCES)	-	600	-
10.2(Test for Density)	-	600	-
10.4(Test for Water Absorption)	-	1200	-
10.5(Test for Swelling in Water)	-	1200	-
10.6(Test for Modulus of Elasticity and Modulus of Rupture)	-	1000	-
10.7(Test for Tensile Strength Perpendicular to Surface)	-	1000	-
10.8(Test for Tensile Strength Perpendicular to Surface After Ageing)	-	3000	-
10.9(Test for Screw Withdrawal Strength)	-	2000	Face-1000 Edge-1000
10.10(Test for Abrasion Resistance)	-	1500	-
10.11(Test for Resistance to Steam)	-	600	-
10.12(Test for Resistance to Crack)	-	600	-
10.13(Test for Resistance to Cigarette Bum)	-	600	-
10.14(Test for Resistance to Stain)	-	600	Complete Testing Charges IS-32900 (For IS 15786 physical tests-15500, Raw material cl. 5.2, 5.3, 5.4-3000, IS 14276 as per clause 5.1-14400 ) 20% discount to BIS GSTIN as per govt. rule
11(Marking)	-	0	-

12 Sep, 2028

-
Included w.e.f. 16.01.2024

IS 14276 (2016)

Cement bonded particle boards - Specification (First Revision)

All

14400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Finish)	-	400	-
7(Dimensions and Tolerances)	-	600	-
8.5(Workability)	-	500	-
10.3, Table-1(Test for Density)	-	600	-
10.5, Table-1(Test for Water Absorption)	-	1200	-
10.6, Table-1(Test for swelling in water)	-	2000	-
10.7, Table-1(Test for modulus of Rupture)	-	1500	Dry & Wet
10.8, Table-1(Test for modulus of Elasticity)	-	1500	Dry & Wet
10.9, Table-1(Test for tensile strength perpendicular to Surface)	-	3500	Dry-1000 & Cyclic-2500
10.1, Table-1(Test for Screw Withdrawal Strength)	-	2000	-
Clause 8.2 Table 1(Moisture content)	-	600	20% discount to BIS GSTIN as per govt. rule

12 Sep, 2028

-
Included w.e.f. 05.01.2024

IS 14616 (1999)

Laminated veneer lumber specification

All (upto 50 mm)

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Dimensions)	-	200	Total testing charges-17700(upto 50mm testing only) 20% discount to BIS GSTIN as per govt rule
6.2(Dimensions)	-	200	-
7(workmanship and finish)	-	600	-
8.2.2(adhesion of plies)	-	4900	Dry State-400, After Cyclic test-2000, After Mycological test-2500
8.2.3, 8.2.4, Table-1(modulus of rupture)	-	1500	-
8.2.3, 8.2.4, Table-1(modulus of elasticity)	-	1500	-
8.2.3, 8.2.4, Table-1(compressive strength parallel to grain)	-	1500	-
8.2.3, 8.2.4, Table-1(horizontal shear a)-parallel to grain ,b)-perpendicular to grain)	-	3000	-
8.2.3, 8.2.4, Table-1(tensile strength parallel to grain )	-	2000	-
8.2.3, 8.2.4, Table-1(screw holding power a)-parallel to grain ,b)-perpendicular to grain)	-	2000	-
8.2.3, 8.2.4, Table-1(thickness swelling in 2 hrs. water soaking)	-	0	-
8.2.4(swelling in wear)	-	800	-
Clause 8.2.1(Moisture content)	-	800	-
8.2.1(moisture content)	-	800	-
6.1(Dimensions)	-	0	-
6.2(Dimensions)	-	0	-
7(workmanship and finish)	-	0	-
8.2.2(adhesion of plies)	-	0	-
8.2.3, 8.2.4, Table-1(modulus of rupture)	-	0	-
8.2.3, 8.2.4, Table-1(modulus of elasticity)	-	0	-
8.2.3, 8.2.4, Table-1(compressive strength parallel to grain)	-	0	-
8.2.3, 8.2.4, Table-1(horizontal shear a)-parallel to grain ,b)-perpendicular to grain)	-	0	-
8.2.3, 8.2.4, Table-1(tensile strength parallel to grain )	-	0	-
8.2.3, 8.2.4, Table-1(screw holding power a)-parallel to grain ,b)-perpendicular to grain)	-	0	-
8.2.3, 8.2.4, Table-1(thickness swelling in 2 hrs. water soaking)	-	0	-
8.2.4(swelling in wear)	-	0	-
Clause 8.2.1(Moisture content)	-	0	-
8.2.1(moisture content)	-	0	-

12 Sep, 2028

-
Included w.e.f. 16.01.2024

IS 2202 : Part 2 (2022)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 2 PARTICLE BOARD HIGH DENSITY FIBRE BOARD MEDIUM DENSITY FIBRE BOARD AND HARDBOARD FACE PANELS Fourth Revision

All

24800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No - 6.1(Timber)	-	2000	Extra charges for Clause 6.1-2000
Clause No -6.2(Alternative Materials (LVL)	-	17500	Extra charges for Clause 6.2-17500
Clause No -6.2(Alternative Materials veneer laminated lumber (VLL))	-	11700	Extra charges for Clause 6.2-11700
Clause No -6.2(Alternative Materials medium density fibre board (MDF))	-	13800	Extra charges for Clause 6.2-13800
Clause No -6.2(Alternative Materials -plywood)	-	17500	Extra charges for Clause 6.2-for IS 710-12600 & IS 303-4900
Clause No -6.2(BWP grade flush door shutter)	-	0	-
Clause No -6.3.1("Face Panels: Particle Board MDF/ HDF Fibre Hardboard")	-	14700	Extra charges for Clause 6.3.1for IS 3087-14700
Clause No -6.4(Adhesive)	-	8000	Extra Charges for Clause 6.4 for MR-7200 & BWP-8000
Clause No -7.1(Construction)	-	0	-
Clause No - 7.3(" MDF board or HDF board ")	-	0	-
Clause No -9.2("Workmanship and finish")	-	200	-
Clause No -10.1(tests for flush door shutters)	-	20000	-
Clause No -10.2(End Immersion Test)	-	3400	BWP-2800, MR-600
Clause No -10.3(Glue Adhesion Test)	-	1200	Testing Charges for -24200-BWP & 22000-MR Extra charges for Clause 6.1, 6.2, 6.3, 6.4, 6.5, 7.2 raw material as mention in remarks 20% discount to BIS GSTIN applicable as per govt rule
Clause No -11(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause No -12("ADDITIONAL REQUIREMENTS FOR ECO MARK")	-	0	-
Clause No - 6.1(Timber)	-	0	-
Clause No -6.2(Alternative Materials (LVL)	-	0	-
Clause No -6.2(Alternative Materials veneer laminated lumber (VLL))	-	0	-
Clause No -6.2(Alternative Materials medium density fibre board (MDF))	-	0	-
Clause No -6.2(Alternative Materials -plywood)	-	0	-
Clause No -6.2(BWP grade flush door shutter)	-	0	-
Clause No -6.3.1("Face Panels: Particle Board MDF/ HDF Fibre Hardboard")	-	0	-
Clause No -6.4(Adhesive)	-	0	-
Clause No -7.1(Construction)	-	0	-
Clause No - 7.3(" MDF board or HDF board ")	-	0	-
Clause No -9.2("Workmanship and finish")	-	0	-
Clause No -10.1(tests for flush door shutters)	-	0	-
Clause No -10.2(End Immersion Test)	-	0	-
Clause No -10.3(Glue Adhesion Test)	-	0	-
Clause No -11(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause No -12("ADDITIONAL REQUIREMENTS FOR ECO MARK")	-	0	-
5(SIZES AND TOLERANCES)	-	0	-
6.5(The swelling in thickness of the particle board, MDF and HDF board for core)	-	800	Testing Charges for -24200-BWP & 22000-MR Extra charges for Clause 6.1, 6.2, 6.3, 6.4, 6.5, 7.2 raw material as mention in remarks 20% discount to BIS GSTIN applicable as per govt rule

12 Sep, 2028

-
Included w.e.f. 16.01.2024

IS 2202 : Part 1 (2023)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Seventh Revision

BWP/MR/All type Designation

24800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(Workmanship & Finish)	-	100	Testing charges-22600 (MR) & 24800 (BWP) 20% discount to BIS GSTIN applicable as per govt rule
9.2(Workmanship & Finish)	-	100	-
9.3(Workmanship & Finish)	-	100	-
11.1(Dimensions - Height)	-	50	-
11.1(Dimensions - Width)	-	50	-
11.1(Dimensions - Thickness)	-	150	-
11.1(Dimensions - Variation in thickness)	-	0	-
11.1(Dimensions - Squareness)	-	150	-
11.12(End immersion test)	-	3400	BWP-2800, MR-600
11.13(Knife Test)	-	400	-
11.14(Glue Adhesion Test)	-	1200	-
9.1(Workmanship & Finish)	-	0	-
9.2(Workmanship & Finish)	-	0	-
9.3(Workmanship & Finish)	-	0	-
11.1(Dimensions - Height)	-	0	-
11.1(Dimensions - Width)	-	0	-
11.1(Dimensions - Thickness)	-	0	-
11.1(Dimensions - Variation in thickness)	-	0	-
11.1(Dimensions - Squareness)	-	0	-
11.12(End immersion test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
4(GRADE)	-	0	-
4(TYPE)	-	0	-
5(SIZES)	-	0	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	0	Extra charges-1500 for Cl. 7.1.1
7.1.1(CONSTRUCTION-Blockboard Core)	-	0	Extra charges-1500 for Cl. 7.1.1
7.1.2(CONSTRUCTION-Blockboard Core)	-	0	Extra charges-1500 for Cl. 7.1.1
7.3.2(CONSTRUCTION-Stiles and Rails)	-	0	-
7.3.2(a)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.2(b)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.2(c)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.3(CONSTRUCTION-Stiles and Rails)	-	0	-
9.1(WORKMANSHIP AND FINISH)	-	0	-
9.2(WORKMANSHIP AND FINISH)	-	0	-
9.3(WORKMANSHIP AND FINISH)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.2(General Flatness Test)	-	600	-
11.2(General Flatness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.3(Local Planeness Test)	-	1250	-
11.4(Impact Indentation Test)	-	1250	-
11.4(Impact Indentation Test)	-	1250	-
11.5(Flexure Test)	-	1250	-
11.5(Flexure Test)	-	0	-
11.6(Edge Loading Test)	-	1250	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.7.1(Shock Resistance Test)	-	1250	-
11.7.2(Shock Resistance Test)	-	0	-
11.8(Buckling Test)	-	1250	-
11.8(Buckling Test)	-	0	-
11.8(Buckling Test)	-	0	-
11.9.2(Slamming Test)	-	1250	-
11.9.3(Slamming Test)	-	0	-
11.10(Misuse Test)	-	1250	-
11.11(Varying Humidity Test)	-	7000	-
11.11(Varying Humidity Test)	-	0	-
11.12(End Immersion Test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	1500	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
Clause 4.2(grades specified)	-	0	-
Clause 5(SIZES)	-	0	-
Clause 6.1.1(species of timber)	-	0	-
Clause 6.1.2(list of species)	-	0	-
Clause 6.1.3(moisture content)	-	0	Extra charges for Cl. 6.1.3-800
Clause 6.2.1(Plywood)	-	0	Extra charges for Cl. 6.2.1-IS 303-4900 & IS 710-12600
Clause 6.2.2(Decorative plywood)	-	0	Extra charges for Cl. 6.2.2-4700
Clause 6.3(Cross-Bands)	-	0	Extra charges for Cl. 6.3-1500
Clause 6.4.1(Commercial Face Veneers)	-	0	Extra charges for Cl. 6.4.1-1500
Clause 6.4.2(Decorative Face Veneers)	-	0	Extra charges for Cl. 6.4.2-1500
Clause 6.6.1(Adhesives)	-	8000	Extra charges for Cl. 6.6.1-BWP-8000 & MR-7200
Clause 6.7(Particle Board)	-	0	Extra charges for Cl. 6.7-1200(swelling in thickness due to general absorption)
Clause 6.8(Medium density fibre board)	-	0	Extra charges for Cl. 6.8-1200(swelling in thickness due to general absorption)
Clause 6.9(Alternative Materials)	-	0	Extra charges for Cl. 6.9-For IS 14616-17700, IS 16171-11700, IS 12406-13800, IS 710-12600, IS 303-4900
Clause 7.1(Blockboard Core)	-	0	Extra charges for Cl. 7.1-1500
Clause 7.2(Particle Board or Medium Density Fibre)	-	0	-
Clause 7.3(Stiles and Rails)	-	0	-
Clause 7.4(Levelling)	-	100	-
Clause 7.5(Face Panel)	-	0	Extra charges for Cl. 7.5-1500
Clause 7.6(Lipping)	-	100	-
Clause 7.7(Rebating)	-	100	-
Clause 7.8(Opening for Glazing)	-	100	-
Clause 7.9(Venetian)	-	100	-
Clause 8.1(Locks)	-	100	-
Clause 9(WORKMANSHIP AND FINISH)	-	0	-
Clause 10.1(Classification of Tests)	-	0	-
Clause 11.1(Dimensions and Squareness Test)	-	0	-
Clause 11.2(General Flatness Test)	-	0	-
Clause 11.3(Local Planeness Test)	-	0	-
Clause 11.4(Impact Indentation Test)	-	0	-
Clause 11.5(Flexure Test)	-	0	-
Clause 11.6(Edge Loading Test)	-	0	-
Clause 11.7(Shock Resistance Test)	-	0	-
Clause 11.8(Buckling Resistance Test)	-	0	-
Clause 11.9(Slamming Test)	-	0	-
Clause 11.10(Misuse Test)	-	0	-
Clause 11.11(Varying Humidity Test)	-	0	-
Clause 11.12(End Immersion Test)	-	0	-
Clause 11.13(Knife Test)	-	0	-
Clause 11.14(Glue Adhesion Test)	-	0	-
Clause 11.15(Screw Withdrawal Resistance Test)	-	0	-
Clause 12(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause 13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	0	-
Clause 14(Marking)	-	0	-
4(Grade, Type and Construction)	-	0	-
5(Sizes and Thickness)	-	0	-
6.1(Timber)	-	0	-
6.2(Plywood for flush door shutter)	-	0	-
6.3(Cross-Bands )	-	0	-
6.4.1(Commercial Face Veneers)	-	0	-
6.4.2(Decorative face veneers)	-	0	-
6.6(Adhesives)	-	0	-
6.7(Particle Board)	-	0	-
6.8(Medium Density Fibre)	-	0	-
6.9(Alternative Materials)	-	0	-
7(Construction)	-	0	-
8.1(Locks)	-	0	-
8.2(Other Fittings)	-	0	-
9(Workmanship and Finish)	-	0	-
10(Tests)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.3(Local Planeness Test)	-	0	-
11.4(Impact Indentation Test)	-	0	-
11.5(Flexure Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.7(Shock Resistance Test)	-	0	-
11.8(Buckling Resistance Test)	-	0	-
11.9(Slamming Test)	-	0	-
11.1(Misuse Test)	-	0	-
11.11(Varying Humidity Test)	-	0	-
11.12(End Immersion Test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
14(Marking )	-	0	-
9.1(Workmanship & Finish)	-	0	-
9.2(Workmanship & Finish)	-	0	-
9.3(Workmanship & Finish)	-	0	-
11.1(Dimensions - Height)	-	0	-
11.1(Dimensions - Width)	-	0	-
11.1(Dimensions - Thickness)	-	0	-
11.1(Dimensions - Variation in thickness)	-	0	-
11.1(Dimensions - Squareness)	-	0	-
11.12(End immersion test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
4(GRADE)	-	0	-
4(TYPE)	-	0	-
5(SIZES)	-	0	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	0	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	0	-
7.1.2(CONSTRUCTION-Blockboard Core)	-	0	-
7.3.2(CONSTRUCTION-Stiles and Rails)	-	0	-
7.3.2(a)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.2(b)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.2(c)(CONSTRUCTION-Stiles and Rails-Joints)	-	0	-
7.3.3(CONSTRUCTION-Stiles and Rails)	-	0	-
9.1(WORKMANSHIP AND FINISH)	-	0	-
9.2(WORKMANSHIP AND FINISH)	-	0	-
9.3(WORKMANSHIP AND FINISH)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.3(Local Planeness Test)	-	0	-
11.4(Impact Indentation Test)	-	0	-
11.4(Impact Indentation Test)	-	0	-
11.5(Flexure Test)	-	0	-
11.5(Flexure Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.7.1(Shock Resistance Test)	-	0	-
11.7.2(Shock Resistance Test)	-	0	-
11.8(Buckling Test)	-	0	-
11.8(Buckling Test)	-	0	-
11.8(Buckling Test)	-	0	-
11.9.2(Slamming Test)	-	0	-
11.9.3(Slamming Test)	-	0	-
11.10(Misuse Test)	-	0	-
11.11(Varying Humidity Test)	-	0	-
11.11(Varying Humidity Test)	-	0	-
11.12(End Immersion Test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
Clause 4.2(grades specified)	-	0	-
Clause 5(SIZES)	-	0	-
Clause 6.1.1(species of timber)	-	0	-
Clause 6.1.2(list of species)	-	0	-
Clause 6.1.3(moisture content)	-	0	-
Clause 6.2.1(Plywood)	-	0	-
Clause 6.2.2(Decorative plywood)	-	0	-
Clause 6.3(Cross-Bands)	-	0	-
Clause 6.4.1(Commercial Face Veneers)	-	0	-
Clause 6.4.2(Decorative Face Veneers)	-	0	-
Clause 6.6.1(Adhesives)	-	0	-
Clause 6.7(Particle Board)	-	0	-
Clause 6.8(Medium density fibre board)	-	0	-
Clause 6.9(Alternative Materials)	-	0	-
Clause 7.1(Blockboard Core)	-	0	-
Clause 7.2(Particle Board or Medium Density Fibre)	-	0	-
Clause 7.3(Stiles and Rails)	-	0	-
Clause 7.4(Levelling)	-	0	-
Clause 7.5(Face Panel)	-	0	-
Clause 7.6(Lipping)	-	0	-
Clause 7.7(Rebating)	-	0	-
Clause 7.8(Opening for Glazing)	-	0	-
Clause 7.9(Venetian)	-	0	-
Clause 8.1(Locks)	-	0	-
Clause 9(WORKMANSHIP AND FINISH)	-	0	-
Clause 10.1(Classification of Tests)	-	0	-
Clause 11.1(Dimensions and Squareness Test)	-	0	-
Clause 11.2(General Flatness Test)	-	0	-
Clause 11.3(Local Planeness Test)	-	0	-
Clause 11.4(Impact Indentation Test)	-	0	-
Clause 11.5(Flexure Test)	-	0	-
Clause 11.6(Edge Loading Test)	-	0	-
Clause 11.7(Shock Resistance Test)	-	0	-
Clause 11.8(Buckling Resistance Test)	-	0	-
Clause 11.9(Slamming Test)	-	0	-
Clause 11.10(Misuse Test)	-	0	-
Clause 11.11(Varying Humidity Test)	-	0	-
Clause 11.12(End Immersion Test)	-	0	-
Clause 11.13(Knife Test)	-	0	-
Clause 11.14(Glue Adhesion Test)	-	0	-
Clause 11.15(Screw Withdrawal Resistance Test)	-	0	-
Clause 12(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause 13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	0	-
Clause 14(Marking)	-	0	-
4(Grade, Type and Construction)	-	0	-
5(Sizes and Thickness)	-	0	-
6.1(Timber)	-	0	-
6.2(Plywood for flush door shutter)	-	0	-
6.3(Cross-Bands )	-	0	-
6.4.1(Commercial Face Veneers)	-	0	-
6.4.2(Decorative face veneers)	-	0	-
6.6(Adhesives)	-	0	-
6.7(Particle Board)	-	0	-
6.8(Medium Density Fibre)	-	0	-
6.9(Alternative Materials)	-	0	-
7(Construction)	-	0	-
8.1(Locks)	-	0	-
8.2(Other Fittings)	-	0	-
9(Workmanship and Finish)	-	0	-
10(Tests)	-	0	-
11.1(Dimensions and Squareness Test)	-	0	-
11.2(General Flatness Test)	-	0	-
11.3(Local Planeness Test)	-	0	-
11.4(Impact Indentation Test)	-	0	-
11.5(Flexure Test)	-	0	-
11.6(Edge Loading Test)	-	0	-
11.7(Shock Resistance Test)	-	0	-
11.8(Buckling Resistance Test)	-	0	-
11.9(Slamming Test)	-	0	-
11.1(Misuse Test)	-	0	-
11.11(Varying Humidity Test)	-	0	-
11.12(End Immersion Test)	-	0	-
11.13(Knife Test)	-	0	-
11.14(Glue Adhesion Test)	-	0	-
11.15(Screw Withdrawal Resistance Test)	-	0	-
14(Marking )	-	0	-

12 Sep, 2028

-
Included w.e.f. 16.01.2024

IS 13801 (2013)

Chequered Cement Concrete Tiles -

All

7350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	600	Complete Testing Charges-7350 20% discount to BIS GSTIN Applicable as per govt rule
Cl 12.1(Concavity & Convexity )	-	750	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	750	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	750	-
Cl 12.4(Water absorption)	-	1000	-
Cl 12.5(Wet transverse strength)	-	1000	-
Cl 12.6(Resistance to wear)	-	2000	-
Cl 11(Finish)	-	500	GSTIN applicable as per govt rule 20% discount to BIS
(Cl 7, 8 &9)(Length, Breadth, Thickness, Difference in length of side between the longest side and shorterst side in the sample shall not exceed 1 mm, Half tiles, Difference in Thickness between the thickest and thinnest tile in the sample shall not exceed 10 percent of minimum thickness, Depth of chequred groove, Thickness of wearing layer.)	-	0	-
Cl 12.1(Concavity & Convexity )	-	0	-
Cl 12.2(Longest gap between the arms of the square and the edge of the title shall not exceed 2 percent of the length.)	-	0	-
Cl 12.3(Shall not exceed 1 percent of the length of the edge.)	-	0	-
Cl 12.4(Water absorption)	-	0	-
Cl 12.5(Wet transverse strength)	-	0	-
Cl 12.6(Resistance to wear)	-	0	-
Cl 11(Finish)	-	0	-
8.3(Thickness of wearing layer)	-	0	-

12 Sep, 2028

-
-

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

All

21700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.20(Spacer nibs)	-	0	(19700 without optional test, 21700 with optional test) 20% discount to BIS GSTIN extra as per govt rule
Clause 7.1.1 (General Quality)	-	400	Spacer nibs charges included 20% discount to BIS GSTIN extra as per govt rule
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	400	20% discount to BIS GSTIN extra as per govt rule
Clause 7.1.3 (Colour and Texture)	-	0	Charges Included in Visual inspection 20% discount to BIS GSTIN extra as per govt rule
Clause 6.3 (Bonding and Delamination between the layers of paver blocks)	-	0	Charges Included in Visual inspection 20% discount to BIS GSTIN extra as per govt rule
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	0	20% discount to BIS GSTIN extra as per govt rule
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Higher)	-	250	20% discount to BIS GSTIN extra as per govt rule
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Higher)	-	0	20% discount to BIS GSTIN extra as per govt rule
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Lower)	-	250	20% discount to BIS GSTIN extra as per govt rule
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Lower)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	400	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	200	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	400	20% discount to BIS GSTIN extra as per govt rule
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	2000	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	3200	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	2000	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	2300	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	2400	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3, Annex F(Individual Failure Load per unit Length)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3, Annex F(Average Failure Load per unit Length)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	2400	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3, Annex G(Individual Breaking Load)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3, Annex G(Average Breaking Load)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 10 cycles)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 25 cycles)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 50 cycles)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Cumulative Weight losses of specimen after 10, 25 & 50 cycles)	-	500	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 10 cycles)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 25 cycles)	-	0	20% discount to BIS GSTIN extra as per govt rule
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 50 cycles)	-	0	20% discount to BIS GSTIN extra as per govt rule

12 Sep, 2028

-
Amendment No. 1 included w.e.f. 10-04-2023

IS 12406 (2021)

Medium density fibre boards for general purpose - Specification

Grade 1 & Grade 2

13800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clauses 5.2, 9 and 10.2.2(Density)	-	600	(For Exterior Grade, Grade-1-13800 & Interior Grade, Grade-2-10800) 20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Variation from mean density)	-	0	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Moisture Content)	-	600	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Variation from mean moisture content)	-	0	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Linear expansion (Thickness Swelling in Water) Due to general Absorption after 24h soaking)	-	3000	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Internal Bond Strength)	-	1000	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Internal Bond strength (i) (After Cyclic test) (ii) (After accelerated water resistance test))	-	3000	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Modulus of Rupture a) Avg. Value b) Min. Individual)	-	500	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Modulus of Elasticity a) Avg. Value b) Min. Individual)	-	500	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Screw withdrawl strength (i) Face (ii) Edge (For thickness >12mm))	-	2000	20% discount to BIS GSTIN extra applicable as per govt. rule
Clauses 5.2, 9 and 10.2.2(Formaldehyde Content (i) For Formaldehyde Class, E1 (ii) For Formaldehyde Class, E2)	-	2000	20% discount to BIS GSTIN extra applicable as per govt. rule
8(DIMENSIONS AND TOLERANCES)	-	600	20% discount to BIS GSTIN extra applicable as per govt. rule

12 Sep, 2028

-
Excluding Table-3 (xii) Steady-State Formaldehyde Emission

IS 10701 (2012)

Structural plywood - Specification (First Revision)

17650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 11.2(Moisture content)	-	400	20% discount for BIS GSTIN extra as per govt rule
11.3(Glue Shear strength in dry state)	-	1000	20% discount for BIS GSTIN extra as per govt rule
11.4.1(Resistance to Water)	-	2500	20% discount for BIS GSTIN extra as per govt rule
11.5(Resistance to Micro-organisms)	-	2800	20% discount for BIS GSTIN extra as per govt rule
11.6(Tensile Strength)	-	1000	20% discount for BIS GSTIN extra as per govt rule
11.7.1(Compressive Strength, Bending Strength, Panel Shear Strength, Plate Shear Strength and Rolling Shear Strngth)	-	6150	20% discount for BIS GSTIN extra as per govt rule
11.8(Wet Bending Strength)	-	2000	20% discount for BIS (Retention of preservative-1000)

12 Sep, 2028

-
-

IS 12894 (2002)

Pulverized fuel ash - Lime bricks - Specification

All

7250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General Requirements)	-	100	20% discount for BIS GSTIN extra as per govt rule
3.2(General Requirements)	-	200	20% discount for BIS GSTIN extra as per govt rule
3.3(General Requirements)	-	0	20% discount for BIS GSTIN extra as per govt rule
3.4(General Requirements)	-	100	20% discount for BIS GSTIN extra as per govt rule
3.5(General Requirements)	-	100	20% discount for BIS GSTIN extra as per govt rule
5.1(Dimensions)	-	1000	20% discount for BIS GSTIN extra as per govt rule
7.1, Table -1(Average Wet Compressive Strength)	-	1500	20% discount for BIS GSTIN extra as per govt rule
7.2(Drying Shrinkage)	-	1500	20% discount for BIS GSTIN extra as per govt rule
7.3(Efflorescence Test)	-	2000	20% discount for BIS GSTIN extra as per govt rule
7.4(Water Absorption)	-	750	20% discount for BIS GSTIN extra as per govt rule

12 Sep, 2028

-
-

IS 13757 (1993)

Burnt Clay Fly Ash Building Bricks-specification

All

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(GENERAL QUALITY)	-	500	20% discount for BIS GSTIN extra as per govt rule
6.1(Dimensions)	-	1000	20% discount for BIS GSTIN extra as per govt rule
6.2(Tolerances)	-	0	20% discount for BIS GSTIN extra as per govt rule
7.1(Compressive Strength)	-	1500	20% discount for BIS GSTIN extra as per govt rule
7.2(Water Absorption)	-	750	20% discount for BIS GSTIN extra as per govt rule
7.3(Efforescence)	-	2000	20% discount for BIS GSTIN extra as per govt rule

12 Sep, 2028

-
-

IS 16720 (2018)

Pulverized Fuel Ash-Cement Bricks- Specification

All

5750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 and fig.1A &1B(Dimensions- Length (L) )	-	300	20% discount for BIS GSTIN extra as per govt rule
4.1 and fig.1A &1B(Dimensions- Width (B) )	-	300	20% discount for BIS GSTIN extra as per govt rule
4.1 and fig.1A &1B(Dimensions- Height (H))	-	300	20% discount for BIS GSTIN extra as per govt rule
4.1 & 4.3 and fig.1A &1B(Dimensions - Depth)	-	100	20% discount for BIS GSTIN extra as per govt rule
4.1 and fig.1A &1B(Dimensions)	-	0	20% discount for BIS GSTIN extra as per govt rule
5 and Tanle 1 (CLASSIFICATION)	-	0	20% discount for BIS GSTIN extra as per govt rule
8.1(GENERAL)	-	500	20% discount for BIS GSTIN extra as per govt rule
8.3(Density Annex C of IS 2185 (Part 1))	-	500	20% discount for BIS GSTIN extra as per govt rule
8.4 and Table 1(Compressive Strength - Individual IS 3495 (Part 1))	-	1500	20% discount for BIS GSTIN extra as per govt rule
8.5(Drying Shrinkage IS 4139)	-	1500	20% discount for BIS GSTIN extra as per govt rule
8.6(Water Absorption IS 3495 (Part 2))	-	750	20% discount for BIS GSTIN extra as per govt rule

12 Sep, 2028

-
-

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

7350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	600	20% discount for BIS GSTIN extra as per govt rule
Cl 11(Suface Finish)	-	500	20% discount for BIS GSTIN extra as per govt rule
Cl 12.2(Concavity & Convexity )	-	750	20% discount for BIS GSTIN extra as per govt rule
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	750	20% discount for BIS GSTIN extra as per govt rule
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	750	20% discount for BIS GSTIN extra as per govt rule
Cl 12.5(Water absorption)	-	1000	20% discount for BIS GSTIN extra as per govt rule
Cl 12.6(Wet transverse strength )	-	1000	20% discount for BIS GSTIN extra as per govt rule
Cl 12.7(Resistance to wear)	-	2000	20% discount for BIS GSTIN extra as per govt rule

12 Sep, 2028

-
-

IS 15558 (2005)

Mini domestic water heater for use with LPG - Specification

All

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.2(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.3(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.4(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.5(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.6(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.7(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.8(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.9(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.10(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.11(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
4.1.12(Construction)	-	50	20% discount for BIS GSTIN extra as per Govt rule
5.1(Materials)	-	0	20% discount for BIS GSTIN extra as per Govt rule
5.2(Materials)	-	200	20% discount for BIS GSTIN extra as per Govt rule
5.3(Materials)	-	100	20% discount for BIS GSTIN extra as per Govt rule
5.4(Materials)	-	200	20% discount for BIS GSTIN extra as per Govt rule
5.5(Materials)	-	0	20% discount for BIS GSTIN extra as per Govt rule
6.1(Connections)	-	100	20% discount for BIS GSTIN extra as per Govt rule
6.2(Connections)	-	200	20% discount for BIS GSTIN extra as per Govt rule
6.3(Connections)	-	100	20% discount for BIS GSTIN extra as per Govt rule
6.4(Connections)	-	200	20% discount for BIS GSTIN extra as per Govt rule
6.5(Connections)	-	200	20% discount for BIS GSTIN extra as per Govt rule
6.6(Gas Inlet Connections)	-	200	20% discount for BIS GSTIN extra as per Govt rule
7(Flame Visibility)	-	100	20% discount for BIS GSTIN extra as per Govt rule
8(Gas Taps)	-	200	20% discount for BIS GSTIN extra as per Govt rule
9(Flame Failure Device)	-	200	20% discount for BIS GSTIN extra as per Govt rule
10(Ignition Device)	-	100	20% discount for BIS GSTIN extra as per Govt rule
11(Protection Against Accidental Overheating)	-	500	20% discount for BIS GSTIN extra as per Govt rule
12(Water Rate Adjuster)	-	500	20% discount for BIS GSTIN extra as per Govt rule
14(Gas Soundness)	-	200	20% discount for BIS GSTIN extra as per Govt rule
15(Water Soundness)	-	300	20% discount for BIS GSTIN extra as per Govt rule
16(Thermal Efficiency)	-	1500	20% discount for BIS GSTIN extra as per Govt rule
17(Combustion)	-	500	20% discount for BIS GSTIN extra as per Govt rule
18(Gas Consumption)	-	2000	20% discount for BIS GSTIN extra as per Govt rule
19.1(Ignition and flame travel)	-	100	20% discount for BIS GSTIN extra as per Govt rule
19.2(Ignition and flame travel)	-	150	20% discount for BIS GSTIN extra as per Govt rule
19.3(Ignition and flame travel)	-	150	20% discount for BIS GSTIN extra as per Govt rule
20(Flame Stability)	-	200	20% discount for BIS GSTIN extra as per Govt rule
21(Noise Control)	-	200	20% discount for BIS GSTIN extra as per Govt rule
22(Flash Back)	-	300	20% discount for BIS GSTIN extra as per Govt rule
23(Resistance to Draught)	-	300	20% discount for BIS GSTIN extra as per Govt rule
24(Fire Hazard And Limiting Temperature )	-	400	20% discount for BIS GSTIN extra as per Govt rule
25(Time For Temperature Rise)	-	500	20% discount for BIS GSTIN extra as per Govt rule
26(Hot Water Output Test)	-	500	20% discount for BIS GSTIN extra as per Govt rule
27(Marking)	-	0	20% discount for BIS GSTIN extra as per Govt rule

12 Sep, 2028

-
-

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

All

21450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
24 (Annex - E)(Combustion (CO and CO2 ratio))	-	900		20% discount for BIS GSTIN extra as per Govt rule

12 Sep, 2028

-
-

IS 15658 (2006)

Precast concrete blocks for paving - Specification

19700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.2(Physical requirement)	-	100	20% discount for BIS
6.1.3(Physical requirement)	-	100	20% discount for BIS
6.1.4(Physical requirement)	-	100	20% discount for BIS
6.2.1 & 7.1(VISUAL INSPECTION)	-	100	20% discount for BIS
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	400	20% discount for BIS
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	100	20% discount for BIS
B-1.3.1(MEAN INDIVIDUAL WIDTH (of all eight test specimens), W)	-	400	20% discount for BIS
B-5(AVERAGE WIDTH (Average for eight test specimens), W)	-	100	20% discount for BIS
B-1.3.1(MEAN INDIVIDUAL LENGTH (of all eight test specimens), L)	-	400	20% discount for BIS
B-5(AVERAGE LENGTH (Average for eight test specimens), L)	-	100	20% discount for BIS
Table 1(MINIMUM PAVER BLOCK THICKNESS)	-	200	20% discount for BIS
B-1.3.2(MEAN INDIVIDUAL THICKNESS (of all eight test specimens), T)	-	200	20% discount for BIS
B-5(AVERAGE THICKNESS (Average for eight test specimens), T)	-	100	20% discount for BIS
B-1.3.3(INDIVIDUAL ASPECT RATIO (L/T) (of all eight test specimens))	-	400	20% discount for BIS
B-5(AVERAGE ASPECT RATIO (L/T) (for eight test specimens))	-	100	20% discount for BIS
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	500	20% discount for BIS
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	100	20% discount for BIS
B-2.3(INDIVIDUAL ARRIS/CHAMFER (of all eight test specimens))	-	500	20% discount for BIS
B-5(AVERAGE ARRIS/CHAMFER (for eight test specimens))	-	100	20% discount for BIS
B-5(INDIVIDUAL PLAN AREA, ASP (of all eight test specimens) )	-	600	20% discount for BIS
B-5(AVERAGE PLAN AREA, ASP (for eight test specimens))	-	100	20% discount for BIS
B-5(INDIVIDUAL WEARING FACE AREA, Asw (of all eight test specimens))	-	600	20% discount for BIS
B-5(AVERAGE WEARING FACE AREA, Asw (for eight test specimens))	-	100	20% discount for BIS
B- 4.3(MEAN INDIVIDUAL SQUARENESS (of all eight test specimens) )	-	600	20% discount for BIS
B-5(AVERAGE SQUARENESS (for eight test specimens))	-	100	20% discount for BIS
6.2.3(THICKNESS OF WEARING LAYER, if the sample is Double Layered (for eight test specimens))	-	0	20% discount for BIS
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	1400	20% discount for BIS
6.2.4(WATER ABSORPTION TEST (Average for three test specimens))	-	100	20% discount for BIS
6.2.5(AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens) )	-	100	20% discount for BIS
6.2.5(AVERAGE COMPRESSIVE STRENGTH (Average for eight test specimens))	-	100	20% discount for BIS
6.2.5.1(INDIVIDUAL COMPRESSIVE STRENGTH (Individual strength of eight test specimen))	-	3000	20% discount for BIS
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	1800	20% discount for BIS
6.2.6(ABRASION RESISTANCE, Dry Condition (For all eight test specimens))	-	200	20% discount for BIS
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	1800	20% discount for BIS
6.2.6(ABRASION RESISTANCE, Wet Condition (For all eight test specimens))	-	200	20% discount for BIS
6.2.7(INDIVIDUAL TENSILE SPLITTING STRENGTH (Individual strength of eight test specimen ))	-	2000	20% discount for BIS
6.2.7(AVERAGE TENSILE SPLITTING STRENGTH (for eight test specimen ))	-	200	20% discount for BIS
Annex G-7(INDIVIDUAL FAILURE LOAD/UNIT LENGTH (Individual Failure Load of eight test specimen ))	-	200	20% discount for BIS
6.2.8(INDIVIDUAL FLEXURAL STRENGTH (Individual strength of eight test specimen ))	-	2000	20% discount for BIS
6.2.8(AVERAGE FLEXURAL STRENGTH (Average strength of eight test specimen ))	-	100	20% discount for BIS
Annex-G-7(INDIVIDUAL BREAKING LOAD (Individual Load of eight test specimen ))	-	200	20% discount for BIS
Annex-G-7(AVERAGE BREAKING LOAD)	-	100	20% discount for BIS GSTIN extra as per govt rule

12 Sep, 2028

-
Amendment 3 & 4 included w.e.f. 21-07-2020.

IS 5509 (2021)

Fire Retardant Plywood - Specification ( Third Revision )

10100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.3 (Table 1)(b) 6 mm and above)	-	400		20% discount for BIS

12 Sep, 2028

-
-

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

Water for Costruction Purpose

6000 View breakup
Rs.4000/- for water for construction purpose Rs. 2000/- for concrete cube testing

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4-(a)-IS: 3025 (P-22)(Volume of 0.02 N NaOH to neutralized 100 ml of water using phenolphthalein indicator)	-	500	20% discount to BIS GSTIN extra as per govt rule
Cl 5.4 (b)(Alkalinity)	-	500	20% discount to BIS GSTIN extra as per govt rule
Cl 5.4 (a)(Acidity)	-	500	20% discount to BIS GSTIN extra as per govt rule
Cl 5.4 Table 1 (i)(Organic Solids)	-	500	20% discount to BIS GSTIN extra as per govt rule
Cl 5.4 Table 1 (ii)(Inorganic Solids)	-	500	20% discount to BIS GSTIN extra as per govt rule
Cl 5.4 Table 1 (iii)(Sulphate)	-	500	20% discount to BIS GSTIN extra as per govt rule
Cl 5.4 Table 1 (iv)(Chloride)	-	500	20% discount to BIS GSTIN extra as per govt rule
Cl 5.4 Table 1 (v)(Suspended Matter)	-	500	20% discount to BIS GSTIN extra as per govt rule
Cl 5.4 .2(pH)	-	500	20% discount to BIS GSTIN extra as per govt rule
16.1(Average Compressive Strength)	-	200	20% discount to BIS GSTIN extra as per govt rule
16.1(Compressive Strength of Individual Samples )	-	600	20% discount to BIS GSTIN extra as per govt rule
16.1(Compressive Strength of Individual Samples )	-	600	20% discount to BIS GSTIN extra as per govt rule
16.1(Compressive Strength of Individual Samples )	-	600	(Construction Water-4000 & Compressive Strength-2000) 20% discount to BIS GSTIN extra as per govt rule

12 Sep, 2028

-
Only for water for construction purpose as per cl.5.4

IS 4990 (2011)

Plywood for concrete shuttering works - Specification (Third Revision)

BWP/CS,CSC,CSFF

13100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Types)	-	0	20 % discount to BIS GSTIN extra as per govt rule
7.2(DIMENSIONS & TOLERANCES )	-	50	20 % discount to BIS
7.2(DIMENSIONS & TOLERANCES )	-	50	20 % discount to BIS
7.3(DIMENSIONS & TOLERANCES )	-	80	20 % discount to BIS
7.4(DIMENSIONS & TOLERANCES )	-	80	20 % discount to BIS
7.4(DIMENSIONS & TOLERANCES )	-	80	20 % discount to BIS
8.1(WORKMANSHIP AND FINISH )	-	30	20 % discount to BIS
8.3(WORKMANSHIP AND FINISH )	-	30	20 % discount to BIS
10.1.1(MOISTURE CONTENT)	-	400	20 % discount to BIS
10.1.2, 10.1.2.1 (Table-1)(GLUE ADHESION IN DRY STATE)	-	600	20 % discount to BIS
10.1.2, 10.1.2.2(GLUE ADHESION IN DRY STATE)	-	400	20 % discount to BIS
10.1.3, 10.1.3.1.1 (Table-1)(RESISTANCE TO WATER TEST)	-	1500	20 % discount to BIS
10.1.3, 10.1.3.1.2(RESISTANCE TO WATER TEST)	-	900	20 % discount to BIS
10.1.4(RESISTANCE TO WATER TEST)	-	600	20 % discount to BIS
10.1.5(MYCOLOGICAL TEST )	-	1800	20 % discount to BIS
10.1.5, 10.1.5.1 (Table-1)(MYCOLOGICAL TEST )	-	600	20 % discount to BIS
10.1.5.2(MYCOLOGICAL TEST )	-	400	20 % discount to BIS
10.1.6(TENSILE STRENGTH)	-	1000	20 % discount to BIS
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	750	20 % discount to BIS
10.1.7 (Table-2)(STATIC BENDING STRENGTH)	-	750	20 % discount to BIS
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1000	20 % discount to BIS
10.1.8 (Table-3)(WET BENDING STRENGTH)	-	1000	20 % discount to BIS
10.1.9(RETENTION OF PRESERVATIVE)	-	1000	20 % discount to BIS
12, 12.1(MARKING)	-	0	20 % discount to BIS
12, 12.2(MARKING)	-	0	20 % discount to BIS

12 Sep, 2028

-
-

IS 383 (2016)

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

Coarse & Fine

12750 View breakup
Coarse -Rs.12750/-, Fine-Rs.9750/-. (Additional test Rs.3600/- for manufactured aggregates)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1000	(For Coarse Aggregate-12750, Fine Aggregate-9750) 20 % discount to BIS GSTIN extra as per Government Rule
5.4.2(a)( Aggregates Impact Value)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
5.4.3(a)( Aggregate Abrasion Value)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Nominal Size of aggregate)	-	800	20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Grading Zone)	-	800	20 % discount to BIS GSTIN extra as per Government Rule
6.4-Table 10(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Nominal Size )	-	800	20 % discount to BIS GSTIN extra as per Government Rule
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.4.2(b)( Aggregates Impact Value)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Nominal Size of aggregate)	-	800	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(i)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 80 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(ii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 63 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(iii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 40 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(iv)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 20 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(v)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 16 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(vi)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 12.5 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(vii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 10 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(viii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 4.75 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.2-Table 7(ix)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 2.36 mm sieve)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(i)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 10mm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(ii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 4.75mm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(iii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 2.36mm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.3-Table 9(vii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 150µm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.4-Table 10(i)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 80mm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.4-Table 10(ii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 40mm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.4-Table 10(iii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 20mm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.4-Table 10(iv)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 4.75mm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.4-Table 10(v)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 600µm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
6.4-Table 10(vi)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 150µm Sieve )	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(fine aggregate))	-	600	20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (fine aggregate))	-	750	20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	750	20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(II) IS:4032(Total sulphate content (fine aggregate))	-	750	20 % discount to BIS GSTIN extra as per Government Rule
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate))	-	1800	20 % discount to BIS GSTIN extra as per Government Rule
5.5-IS: 2386 (P-5)(Soundness (fine aggregate))	-	1500	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (Note-3) IS-2386 (P-2)(Mica content (fine aggregate))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Effect of organic impurities on strength of mortar (fine aggregate))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Effect of organic impurities on strength of mortar (fine aggregate))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Organic impurities (fine aggregate))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (fine aggregate))	-	1800	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (fine aggregate))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (fine aggregate ))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (fine aggregate ))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(coarse aggregate))	-	600	20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (coarse aggregate))	-	750	20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(III) BN EN: 1744(Water soluble chloride content (coarse aggregate))	-	750	20 % discount to BIS GSTIN extra as per Government Rule
5.7-Table-3-(II) BN EN: 1744(Total sulphate content (coarse aggregate))	-	750	20 % discount to BIS GSTIN extra as per Government Rule
5.5-IS: 2386 (P-5)(Soundness (coarse aggregate))	-	1500	20 % discount to BIS GSTIN extra as per Government Rule
5.3-IS: 2386 (P-1)(Combined elongation & flakiness index (coarse aggregate))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (coarse aggregate))	-	1800	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (iv) IS-2386 (P-2)(Soft fragments (coarse aggregate))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (coarse aggregate))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (coarse aggregate ))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (coarse aggregate ))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (coarse aggregate))	-	1800	20 % discount to BIS GSTIN extra as per Government Rule
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
Clause 5.1(General)	-	0	20 % discount to BIS GSTIN extra as per Government Rule

12 Sep, 2028

-
-

IS 15380 (2003)

Moulded Raised High Density Fibre (HDF) Panel Doors -

Heavy & Light Duty

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, Table-1(dimension )	-	400	Testing charges applicable for only Raised fibre board skin 20 % discount to BIS GSTIN extra as per govt rule
7.1(Heavy duty (Construction))	-	0	20 % discount to BIS GSTIN extra as per govt rule
7.2(Light duty)	-	0	20 % discount to BIS GSTIN extra as per govt rule
7.3(Empanelment)	-	25	20 % discount to BIS GSTIN extra as per govt rule
7.4(Lipping )	-	25	20 % discount to BIS GSTIN extra as per govt rule
7.5(rebating )	-	25	20 % discount to BIS GSTIN extra as per govt rule
11.1(Dimension and squareness test)	-	400	20 % discount to BIS GSTIN extra as per govt rule
11.2(General flatness test)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.3(low Planeness Teat)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.4(Impact Indentation Test)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.5(Flexure Test)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.6(edge loading test)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.7(shock resistance test)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.8(Buckling Test)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.9(slamming Test)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.1(misuse test)	-	750	20 % discount to BIS GSTIN extra as per govt rule
11.11(varying humidity test)	-	2100	20 % discount to BIS GSTIN extra as per govt rule
11.12(end immersion test)	-	1600	20 % discount to BIS GSTIN extra as per govt rule
11.13(glue adhesion test)	-	800	20 % discount to BIS GSTIN extra as per govt rule
11.14(screw withdrawal resistance test)	-	850	20 % discount to BIS GSTIN extra as per Government Rule
Clause 6.2(Moisture content)	-	600	Testing charges applicable for only Raised fibre board skin 20 % discount to BIS GSTIN extra as per govt rule
Clause 6.2(Formaldehyde emission)	-	2000	Testing charges applicable for only Raised fibre board skin (Complete testing charges for Raised fibre board skin=11000) 20 % discount to BIS GSTIN extra as per govt rule
9(workmanship and finish)	-	25	20 % discount to BIS GSTIN extra as per govt rule

12 Sep, 2028

-
-

IS 3564 (1995)

Hydraulically Regulated Door Closers -Specification

Type A & B

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(Marking)	-	0	Testing charges without materials test (materials test excluded in the scope) 20 % discount to BIS GSTIN extra as per Government Rule
12(Packing)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
13(Accessories)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
6(Nominal Sizes)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
8(Essential Requirements)	-	1500	20 % discount to BIS GSTIN extra as per Government Rule
9(Finish)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
10Annex B(Test)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
B-1.4(c) Performance Requirements)	-	2000	20 % discount to BIS GSTIN extra as per Government Rule
B-1.5(d) Endurance Test)	-	12000	20 % discount to BIS GSTIN extra as per Government Rule
B-1.2(a) Visual Inspection)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
B-1.3(b) Surface)	-	500	20 % discount to BIS GSTIN extra as per Government Rule

12 Sep, 2028

-
(Except Material test )

IS 14587 (1998)

Prelaminated Medium Density Fibre Board -specification

Exterior & Interior/Grade I/Grade II/Type I-IV

17100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions and tolerances)	-	600	(For Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100) 20 % discount to BIS GSTIN extra as per Government Rule
10.2, Table-1(Test for Density)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
10.4, Table-1(Test for Water Absorption)	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
10.5(test for swelling in water)	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
10.6(test for modulis of rupture)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
10.7(Test for tensile strength perpendicular to Surface)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
10.8(Test for tensile strength perpendicular to Surface after ageing )	-	3000	20 % discount to BIS GSTIN extra as per Government Rule
10.9(test screw withdrawal strength)	-	2000	20 % discount to BIS GSTIN extra as per Government Rule
10.1(test for surface abrasion resistance)	-	1500	20 % discount to BIS GSTIN extra as per Government Rule
10.11(test for resistance to steam)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
10.12(test for resistance to crack)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
10.13(test for resistance to cigarette burn)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
10.14(test for resistance to stain)	-	600	20 % discount to BIS GSTIN extra as per Government Rule

12 Sep, 2028

-
-

IS 12823 (2015)

Prelaminated Particle Boards from Wood and other Lignocellulosic Material - Specification ( First Revision )

Exterior & Interior/Grade I/Grade II/Type I-IV

17100 View breakup
Rs.17100/- for exterior grade, Gr-1 & Rs.14100/- for interior grade, Gr-2

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4(Grades & Types)	-	0	(For Exterior Grade-Rs. 17100 & Interior Grade- Rs.14100) 20 % discount to BIS GSTIN extra as per Government Rule
Cl 6(Manufacture)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
Cl 7(Finish)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
Cl 8(Dimensions & Tolerances)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.2(Test For Density)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.3(Test For Moisture Content)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.4(For Water AbsorptionTest )	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.5(For Swelling in water Test )	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.6(Tesr For Modulus Of Elasticity & Mudulus Of Rupture)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.7(For Determination of Tensile Strength Perpendicular to Surface)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.8(For Determination of Tensile Strength Perpendicular to Surface After Ageing Test)	-	3000	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.9(Test For Screw Withdrawal Strength)	-	2000	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.10 & Annex C( Test For Abrasion Resistance)	-	1500	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.11 & Annex D( Test For Resistance to Steam)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.12 & Annex E( Test For Crack Resistance)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.13 & Annex F( Test For Resistance to Cigarette Burn)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
Cl 10.14 & Annex G( Test For Resistance to Stain)	-	600	20 % discount to BIS GSTIN extra as per Government Rule

12 Sep, 2028

-
Revised IS 12823:2015 included w.e.f. 15.10.2019

IS 3087 (2005)

Practicle boards of wood and other lingnocellulosic materials (medium density) for general purposes -Specification

Interior & Exterior/FPS/FPT-1/FPT-2/XPS/XPT

14700 View breakup
Rs.14700/- (for exterior Grade, Grade-1), Rs.11700/- (for interior grade, Grade-2)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1 (i) Table 1(Density Variation (Flat Pressed Single Layer))	-	600	(For Exterior Grade-Rs.14700, Interior grade-11700) 20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Single Layer))	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) Table 1 (b)(Water absorption, 24h soacking (Flat Pressed Single Layer))	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Single Layer))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Single Layer))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Single Layer))	-	1500	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Single Layer))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Single Layer))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Single Layer))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Single Layer))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Single Layer))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Single Layer))	-	1000	C20 % discount to BIS GSTIN extra as per Government Rule
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 1))	-	600	20 % discount to BIS GSTIN extra as per Government Rule
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 2))	-	600	20 % discount to BIS GSTIN extra as per Government Rule
1 (i) Table 1(Density Variation (Extrusion Pressed Solids) XPS)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
1 (i) Table 1(Density Variation (Extrusion Pressed Tubular) XPS)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 1))	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 2))	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Solids) XPS)	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Tubular) XPS)	-	400	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 1))	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 2))	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Solids) XPS)	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Tubular) XPS)	-	800	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 1))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 2))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Solids) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Tubular) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Single Layer))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 1))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 2))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Solids) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Tubular) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 1))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 2))	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Solids) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Tubular) XPS)	-	500	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 1))	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 2))	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Solids) XPS)	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Tubular) XPS)	-	1200	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 1))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Three Layer grade 1))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 2))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Three Layer grade 2))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Solids) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Extrusion Pressed Solids) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Tubular) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Extrusion Pressed Tubular) XPT)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 1))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Three Layer grade 1))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 2))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Three Layer grade 2))	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Solids) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Extrusion Pressed Solids) XPS)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Tubular) XPT)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Extrusion Pressed Tubular) XPT)	-	250	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface,Upto 20mm thickness (Flat Pressed Three Layer grade 1))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Solids) XPS)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface,Above 20mm thickness (Flat Pressed Three Layer grade 1))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Three Layer grade 2))	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Solids) XPS)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1000	20 % discount to BIS GSTIN extra as per Government Rule
7(Finish)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
8.3(Dimensional Tolerances)	-	600	20 % discount to BIS GSTIN extra as per Government Rule
11.10(screw withdrawal strength)	-	2000	20 % discount to BIS GSTIN extra as per Government Rule
9.2, 11.4(Moisture content)	-	600	20 % discount to BIS GSTIN extra as per Government Rule

12 Sep, 2028

-
-

IS 848 (2006)

Synthetic resin adhesives for plywood (Phenolic And Aminoplastic) - Specification (Second Revision)

MR-BWR-BWP

8000 View breakup
For MR Rs.2000/- (without cyclic test) & Rs.7200/- (with cyclic test) For BWR & BWP Rs.2000/- (without cyclic test) & Rs.8000/- (with cyclic test)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 Table (i)(BWP (BOiling WaterProof))	-	6000	BWP-8000 (with cyclic test) & 2000 without cyclic test BWR-8000 (with cyclic test) & 2000 without cyclic test MR-7200 (with cyclic test) & 2000 without cyclic test 20 % discount to BIS GSTIN extra as per Government Rule
4 Table (i)(BWR (Boiling Water Resistant))	-	6000	20 % discount to BIS GSTIN extra as per Government Rule
4 Table (i)(MR (Moisture Ressistant))	-	5200	20 % discount to BIS GSTIN extra as per Government Rule
5,7.4(Keeping Quality (Resistance to heat Polymerization))	-	0	20 % discount to BIS GSTIN extra as per Government Rule
7.4(Acidity and Alkalinity ( pH))	-	2000	20 % discount to BIS GSTIN extra as per Government Rule

12 Sep, 2028

-
-

IS 1328 (1996)

Veneered Decorative Plywood -Specification

MR-BWR

4700 View breakup
Rs.4700/- for MR Grade & for BWR Grade

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Grade - For BWR)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
4.1(Grade - For MR)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
4.2(Type - For Type 1)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
4.2(Type - For Type 2)	-	0	20 % discount to BIS GSTIN extra as per Government Rule
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	200	20 % discount to BIS GSTIN extra as per Government Rule
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	200	20 % discount to BIS GSTIN extra as per Government Rule
7.1.2(Requirements - Other defects - For Type 1 - Cl. 7.1.2)	-	200	20 % discount to BIS GSTIN extra as per Government Rule
7.2.2(Requirements - Other defects - For Type 2 - Cl. 7.2.2.)	-	200	20 % discount to BIS GSTIN extra as per Government Rule
7.1.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 1 - Cl. 7.1.3)	-	200	20 % discount to BIS GSTIN extra as per Government Rule
7.2.3(Requirements - Other Charcteristics and Manufacturing Defects - For Type 2 - Cl. 7.2.3)	-	200	20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Length - Cl. 8)	-	50	20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Width - Cl. 8)	-	50	20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	100	20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	100	20 % discount to BIS GSTIN extra as per Government Rule
8(Dimensions & Tolerances - Squareness - Annexure C)	-	100	20 % discount to BIS GSTIN extra as per Government Rule
9(Finish - Cl. 9.1, 8.3)	-	100	20 % discount to BIS GSTIN extra as per Government Rule
9(Finish - Cl. 9.2, 8.3)	-	100	20 % discount to BIS GSTIN extra as per Government Rule
11(Tests - Moisture Content - Part 1 of IS 1734)	-	400	20 % discount to BIS GSTIN extra as per Government Rule
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	2000	20 % discount to BIS GSTIN extra as per Government Rule
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	2000	20 % discount to BIS GSTIN extra as per Government Rule For Static Bending Strength test Rs. 1300 included in complete testing charge

12 Sep, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Hindustaan Testing Solutions LLP, Ambala

Plot No. 36,Sector 1, HSIIDC IGC Saha, Ambala Cantt, Ambala Cantt, Ambala, Haryana, 133104

9355002828 hindustaantesthouse@gmail.com

Scope List