BIS - LIMS (Laboratory Information Management System)

ATCC TEST LABS LLP

KHASRA NO. 45/6, SITUATED IN THE AREA, VILLAGE PRAHLADPUR BANGER,, North West Delhi, Delhi, 110042, Delhi, North West, Delhi, 110042

9891606632 info@atcctestlabs.com

Scope List

Reset

100 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS/IEC 62368 : Part 1 (2023)

Audio Video Information and Communication Technology Equipment - Part 1: Safety Requirements (Second Revision)

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General- materials, components)	-	500	25 % discount to BIS
Cl-4.2(Energy source classifications)	-	500	25 % discount to BIS
Cl-4.3(Protection against energy sources)	-	500	25 % discount to BIS
Cl-4.4(Safeguards)	-	500	25 % discount to BIS
Cl-4.5(Explosion)	-	500	25 % discount to BIS
Cl-4.6(Fixing of conductors and conductive parts)	-	500	25 % discount to BIS
Cl-4.7(Equipment for direct insertion into mains socket-outlets)	-	500	25 % discount to BIS
Cl-4.8(Equipment containing coin or button cell batteries)	-	500	25 % discount to BIS
Cl-4.9(Likelihood of fire or shock due to entry of conductive objects)	-	500	25 % discount to BIS
Cl-4.10(Components requirements)	-	500	25 % discount to BIS
Cl-5.1(General- Electrically-caused injury)	-	500	25 % discount to BIS
Cl-5.2(Classification and limits of electrical energy sources)	-	500	25 % discount to BIS
Cl-5.3(Protection against electrical energy sources)	-	500	25 % discount to BIS
Cl-5.4(Insulation materials and requirements)	-	500	25 % discount to BIS
Cl-5.5(Components as safeguards)	-	500	25 % discount to BIS
Cl-5.6(Protective conductor)	-	500	25 % discount to BIS
Cl-5.7(Prospective touch voltage, touch current and protective conductor current)	-	500	25 % discount to BIS
Cl-5.8(Backfeed safeguard in battery backed up supplies)	-	2000	25 % discount to BIS
Cl-6.1(General- Electrically-caused fire)	-	500	25 % discount to BIS
Cl-6.2(Classification of power sources and potential ignition sources)	-	500	25 % discount to BIS
Cl-6.3(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	1000	25 % discount to BIS
Cl-6.4(Safeguards against fire under single fault conditions)	-	2000	25 % discount to BIS
Cl-6.5(Internal and external wiring)	-	500	25 % discount to BIS
Cl-7.1(General- Injury caused by hazardous substances)	-	700	25 % discount to BIS
Cl-7.2(Reduction of exposure to hazardous substances)	-	600	25 % discount to BIS
Cl-7.3(Ozone exposure)	-	500	25 % discount to BIS
Cl-7.4(Use of personal safeguards or personal protective equipment (PPE)	-	500	25 % discount to BIS
Cl-7.5(Use of instructional safeguards and instructions)	-	500	25 % discount to BIS
Cl-8.1(General- Mechanically-caused injury)	-	500	25 % discount to BIS
Cl-8.2(Mechanical energy source classifications)	-	500	25 % discount to BIS
Cl-8.3(Safeguards against mechanical energy sources)	-	500	25 % discount to BIS
Cl-8.4(Safeguards against parts with sharp edges and corners)	-	500	25 % discount to BIS
Cl-8.5(Safeguards against moving parts)	-	500	25 % discount to BIS
Cl-8.6(Stability of equipment)	-	1000	25 % discount to BIS
Cl-8.7(Equipment mounted to a wall, ceiling or other structure)	-	1000	25 % discount to BIS
Cl-8.8(Handle strength)	-	500	25 % discount to BIS
Cl-8.9(Wheels or casters attachment requirements)	-	500	25 % discount to BIS
Cl-8.10(Carts, stands, and similar carriers)	-	500	25 % discount to BIS
Cl-8.11(Mounting means for slide-rail mounted equipment (SRME))	-	500	25 % discount to BIS
Cl-9.1(General-Thermal burn injury)	-	500	25 % discount to BIS
Cl-9.2(Thermal energy source classifications)	-	500	25 % discount to BIS
Cl-9.3(Touch temperature limits)	-	700	25 % discount to BIS
Cl-9.4(Safeguards against thermal energy sources)	-	500	25 % discount to BIS
Cl-9.5(Requirements for safeguards)	-	500	25 % discount to BIS
Cl-9.6(Requirements for wireless power transmitters)	-	500	25 % discount to BIS
Annex A(Examples of equipment within the scope of this document)	-	500	25 % discount to BIS
Annex B(General- Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	500	25 % discount to BIS
Annex B-2(Normal operating conditions)	-	500	25 % discount to BIS
Annex B-3(Simulated abnormal operating conditions)	-	2000	25 % discount to BIS
Annex B-4(Simulated single fault conditions)	-	1500	25 % discount to BIS
Annex D-1(Impulse test generators)	-	2000	25 % discount to BIS
Annex D-2(Antenna interface test generator)	-	1100	25 % discount to BIS
Annex D-3(Electronic pulse generator)	-	2500	25 % discount to BIS
Annex E-1(Electrical energy source classification for audio signals)	-	1000	25 % discount to BIS
Annex E-2(Audio signals used during test)	-	700	25 % discount to BIS
Annex E-3(Operating conditions of equipment containing an audio amplifier)	-	500	25 % discount to BIS
Annex F-1(General-Equipment markings, instructions, and instructional safeguards)	-	500	25 % discount to BIS
Annex F-2(Letter symbols and graphical symbols)	-	500	25 % discount to BIS
Annex F-3(Equipment markings)	-	500	25 % discount to BIS
Annex F-4(Instructions)	-	500	25 % discount to BIS
Annex F-5(Instructional safeguards)	-	500	25 % discount to BIS
Annex G-1(Switches)	-	500	25 % discount to BIS
Annex G-2(Relays)	-	500	25 % discount to BIS
Annex G-3(Protective devices)	-	500	25 % discount to BIS
Annex G-4(Connectors)	-	500	25 % discount to BIS
Annex G-5(Wound components)	-	500	25 % discount to BIS
Annex G-6(Wire insulation)	-	500	25 % discount to BIS
Annex G-7(Mains power supply cords and interconnection cables)	-	500	25 % discount to BIS
Annex G-8(Varistors)	-	500	25 % discount to BIS
Annex G-9(Integrated circuit (IC) current limiters)	-	500	25 % discount to BIS
Annex G-10(Resistors)	-	500	25 % discount to BIS
Annex G-11(Capacitors and RC units)	-	500	25 % discount to BIS
Annex G-12(Optocouplers)	-	500	25 % discount to BIS
Annex G-13(Printed boards)	-	500	25 % discount to BIS
Annex G-14(Coatings on component terminals)	-	500	25 % discount to BIS
Annex G-15(Pressurized liquid filled components or LFC assemblies)	-	500	25 % discount to BIS
Annex G-16(IC that includes a capacitor discharge function (ICX))	-	500	25 % discount to BIS
Annex H-1(General- Criteria for telephone ringing signals)	-	500	25 % discount to BIS
Annex H-3(Method B)	-	500	25 % discount to BIS
Annex I(Overvoltage categories (see IEC 60364-4-44))	-	500	25 % discount to BIS
Annex J-1(General-Insulated winding wires for use without interleaved insulation)	-	500	25 % discount to BIS
Annex J-2(Type tests)	-	500	25 % discount to BIS
Annex J-3(Testing during manufacturing)	-	500	25 % discount to BIS
Annex K-1(General- Safety interlocks)	-	500	25 % discount to BIS
Annex K-2(Components of the safety interlock safeguard mechanism)	-	500	25 % discount to BIS
Annex K-3(Inadvertent change of operating mode)	-	500	25 % discount to BIS
Annex K-4(Interlock safeguard override)	-	500	25 % discount to BIS
Annex K-5(Fail-safe)	-	500	25 % discount to BIS
Annex K-6(Mechanically operated safety interlocks)	-	500	25 % discount to BIS
Annex K-7(Interlock circuit isolation)	-	500	25 % discount to BIS
Annex L-1(General requirements)	-	500	25 % discount to BIS
Annex L-2(Permanently connected equipment)	-	500	25 % discount to BIS
Annex L-3()	-	500	25 % discount to BIS
Annex L-4(Single-phase equipment)	-	500	25 % discount to BIS
Annex L-5(Three-phase equipment)	-	500	25 % discount to BIS
Annex L-6(Switches as disconnect devices)	-	500	25 % discount to BIS
Annex L-7(Plugs as disconnect devices)	-	500	25 % discount to BIS
Annex L-8(Multiple power sources)	-	500	25 % discount to BIS
Annex L-9(Compliance criteria)	-	500	25 % discount to BIS
Annex M-1(General requirements)	-	500	25 % discount to BIS
Annex M-2(Safety of batteries and their cells)	-	500	25 % discount to BIS
Annex M-3(Protection circuits for batteries provided within the equipment)	-	500	25 % discount to BIS
Annex M-4(Additional safeguards for equipment containing a secondary lithium battery)	-	500	25 % discount to BIS
Annex M-5(Risk of burn due to short-circuit during carrying)	-	500	25 % discount to BIS
Annex M-6(Safeguards against short-circuits)	-	500	25 % discount to BIS
Annex M-7(Risk of explosion from lead acid and NiCd batteries)	-	500	25 % discount to BIS
Annex M-8("Protection against internal ignition from external spark sources of rechargeable batteries with aqueous electrolyte")	-	500	25 % discount to BIS
Annex M-9(Preventing electrolyte spillage)	-	500	25 % discount to BIS
Annex M-10(Instructions to prevent reasonably foreseeable misuse)	-	500	25 % discount to BIS
Annex N(Electrochemical potentials (V))	-	500	25 % discount to BIS
Annex O(Measurement of creepage distances and clearances)	-	500	25 % discount to BIS
Annex P-1(General-Safeguards against conductive objects)	-	500	25 % discount to BIS
Annex P-2(Safeguards against entry or consequences of entry of a foreign object)	-	500	25 % discount to BIS
Annex P-3(Safeguards against spillage of internal liquids)	-	500	25 % discount to BIS
Annex P-4(Metallized coatings and adhesives securing parts)	-	500	25 % discount to BIS
Annex Q-1(Limited power source)	-	500	25 % discount to BIS
Annex Q-2(Test for external circuits – paired conductor cable)	-	500	25 % discount to BIS
Annex R(Limited short-circuit test)	-	500	25 % discount to BIS
Annex S-1(Flammability test for fire enclosure and fire barrier materials of equipment where the steady state power does not exceed 4 000 W)	-	500	25 % discount to BIS
Annex S-2(Flammability test for fire enclosure and fire barrier integrity)	-	500	25 % discount to BIS
Annex S-3(Flammability tests for the bottom of a fire enclosure)	-	500	25 % discount to BIS
Annex S-4(Flammability classification of materials)	-	500	25 % discount to BIS
Annex S-5(Flammability test for fire enclosure materials of equipment with a steady state power exceeding 4 000 W)	-	500	25 % discount to BIS
Annex S-6(Grille covering material, cloth, and reticulated foam)	-	500	25 % discount to BIS
Annex T-1(General-Mechanical strength tests)	-	500	25 % discount to BIS
Annex T-2(Steady force test, 10 N)	-	500	25 % discount to BIS
Annex T-3(Steady force test, 30 N)	-	500	25 % discount to BIS
Annex T-4(Steady force test, 100 N)	-	500	25 % discount to BIS
Annex T-5(Steady force test, 250 N)	-	500	25 % discount to BIS
Annex T-6(Enclosure impact test)	-	500	25 % discount to BIS
Annex T-7(Drop test)	-	500	25 % discount to BIS
Annex T-8(Stress relief test)	-	500	25 % discount to BIS
Annex T-9(Glass impact test)	-	500	25 % discount to BIS
Annex T-10(Glass fragmentation test)	-	500	25 % discount to BIS
Annex T-11(Test for telescoping or rod antennas)	-	500	25 % discount to BIS
Annex V-1(Accessible parts of equipment)	-	500	25 % discount to BIS
Annex V-2(Accessible part criterion)	-	500	25 % discount to BIS
Annex W(Comparison of terms introduced in this document)	-	500	25 % discount to BIS
Annex X("Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420 V peak (300 V RMS)")	-	500	25 % discount to BIS
Annex Y-1(General- Construction requirements for outdoor enclosures)	-	500	25 % discount to BIS
Annex Y-3(Resistance to corrosion)	-	500	25 % discount to BIS
Annex Y-4(Gaskets)	-	500	25 % discount to BIS
Annex Y-5(Protection of equipment within an outdoor enclosure)	-	500	25 % discount to BIS
Annex Y-6(Mechanical strength of enclosures)	-	500	25 % discount to BIS
Annex H-2(Method A)	-	500	25 % discount to BIS
Cl-4.1(General- materials, components)	-	500	25 % discount to BIS
Cl-4.2(Energy source classifications)	-	500	25 % discount to BIS
Cl-4.3(Protection against energy sources)	-	500	25 % discount to BIS
Cl-4.4(Safeguards)	-	500	25 % discount to BIS
Cl-4.5(Explosion)	-	500	25 % discount to BIS
Cl-4.6(Fixing of conductors and conductive parts)	-	500	25 % discount to BIS
Cl-4.7(Equipment for direct insertion into mains socket-outlets)	-	500	25 % discount to BIS
Cl-4.8(Equipment containing coin or button cell batteries)	-	500	25 % discount to BIS
Cl-4.9(Likelihood of fire or shock due to entry of conductive objects)	-	500	25 % discount to BIS
Cl-4.10(Components requirements)	-	500	25 % discount to BIS
Cl-5.1(General- Electrically-caused injury)	-	500	25 % discount to BIS
Cl-5.2(Classification and limits of electrical energy sources)	-	500	25 % discount to BIS
Cl-5.3(Protection against electrical energy sources)	-	500	25 % discount to BIS
Cl-5.4(Insulation materials and requirements)	-	500	25 % discount to BIS
Cl-5.5(Components as safeguards)	-	500	25 % discount to BIS
Cl-5.6(Protective conductor)	-	500	25 % discount to BIS
Cl-5.7(Prospective touch voltage, touch current and protective conductor current)	-	500	25 % discount to BIS
Cl-5.8(Backfeed safeguard in battery backed up supplies)	-	500	25 % discount to BIS
Cl-6.1(General- Electrically-caused fire)	-	500	25 % discount to BIS
Cl-6.2(Classification of power sources and potential ignition sources)	-	500	25 % discount to BIS
Cl-6.3(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	500	25 % discount to BIS
Cl-6.4(Safeguards against fire under single fault conditions)	-	500	25 % discount to BIS
Cl-6.5(Internal and external wiring)	-	500	25 % discount to BIS
Cl-7.1(General- Injury caused by hazardous substances)	-	500	25 % discount to BIS
Cl-7.2(Reduction of exposure to hazardous substances)	-	500	25 % discount to BIS
Cl-7.3(Ozone exposure)	-	500	25 % discount to BIS
Cl-7.4(Use of personal safeguards or personal protective equipment (PPE)	-	500	25 % discount to BIS
Cl-7.5(Use of instructional safeguards and instructions)	-	500	25 % discount to BIS
Cl-8.1(General- Mechanically-caused injury)	-	500	25 % discount to BIS
Cl-8.2(Mechanical energy source classifications)	-	500	25 % discount to BIS
Cl-8.3(Safeguards against mechanical energy sources)	-	500	25 % discount to BIS
Cl-8.4(Safeguards against parts with sharp edges and corners)	-	500	25 % discount to BIS
Cl-8.5(Safeguards against moving parts)	-	500	25 % discount to BIS
Cl-8.6(Stability of equipment)	-	500	25 % discount to BIS
Cl-8.7(Equipment mounted to a wall, ceiling or other structure)	-	500	25 % discount to BIS
Cl-8.8(Handle strength)	-	500	25 % discount to BIS
Cl-8.9(Wheels or casters attachment requirements)	-	500	25 % discount to BIS
Cl-8.10(Carts, stands, and similar carriers)	-	500	25 % discount to BIS
Cl-8.11(Mounting means for slide-rail mounted equipment (SRME))	-	500	25 % discount to BIS
Cl-9.1(General-Thermal burn injury)	-	500	25 % discount to BIS
Cl-9.2(Thermal energy source classifications)	-	500	25 % discount to BIS
Cl-9.3(Touch temperature limits)	-	500	25 % discount to BIS
Cl-9.4(Safeguards against thermal energy sources)	-	500	25 % discount to BIS
Cl-9.5(Requirements for safeguards)	-	500	25 % discount to BIS
Cl-9.6(Requirements for wireless power transmitters)	-	500	25 % discount to BIS
Annex A(Examples of equipment within the scope of this document)	-	500	25 % discount to BIS
Annex B(General- Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	500	25 % discount to BIS
Annex B-2(Normal operating conditions)	-	500	25 % discount to BIS
Annex B-3(Simulated abnormal operating conditions)	-	500	25 % discount to BIS
Annex B-4(Simulated single fault conditions)	-	500	25 % discount to BIS
Annex D-1(Impulse test generators)	-	500	25 % discount to BIS
Annex D-2(Antenna interface test generator)	-	500	25 % discount to BIS
Annex D-3(Electronic pulse generator)	-	500	25 % discount to BIS
Annex E-1(Electrical energy source classification for audio signals)	-	500	25 % discount to BIS
Annex E-2(Audio signals used during test)	-	500	25 % discount to BIS
Annex E-3(Operating conditions of equipment containing an audio amplifier)	-	500	25 % discount to BIS
Annex F-1(General-Equipment markings, instructions, and instructional safeguards)	-	500	25 % discount to BIS
Annex F-2(Letter symbols and graphical symbols)	-	500	25 % discount to BIS
Annex F-3(Equipment markings)	-	500	25 % discount to BIS
Annex F-4(Instructions)	-	500	25 % discount to BIS
Annex F-5(Instructional safeguards)	-	500	25 % discount to BIS
Annex G-1(Switches)	-	500	25 % discount to BIS
Annex G-2(Relays)	-	500	25 % discount to BIS
Annex G-3(Protective devices)	-	500	25 % discount to BIS
Annex G-4(Connectors)	-	500	25 % discount to BIS
Annex G-5(Wound components)	-	500	25 % discount to BIS
Annex G-6(Wire insulation)	-	500	25 % discount to BIS
Annex G-7(Mains power supply cords and interconnection cables)	-	500	25 % discount to BIS
Annex G-8(Varistors)	-	500	25 % discount to BIS
Annex G-9(Integrated circuit (IC) current limiters)	-	500	25 % discount to BIS
Annex G-10(Resistors)	-	500	25 % discount to BIS
Annex G-11(Capacitors and RC units)	-	500	25 % discount to BIS
Annex G-12(Optocouplers)	-	500	25 % discount to BIS
Annex G-13(Printed boards)	-	500	25 % discount to BIS
Annex G-14(Coatings on component terminals)	-	500	25 % discount to BIS
Annex G-15(Pressurized liquid filled components or LFC assemblies)	-	500	25 % discount to BIS
Annex G-16(IC that includes a capacitor discharge function (ICX))	-	500	25 % discount to BIS
Annex H-1(General- Criteria for telephone ringing signals)	-	500	25 % discount to BIS
Annex H-3(Method B)	-	500	25 % discount to BIS
Annex I(Overvoltage categories (see IEC 60364-4-44))	-	500	25 % discount to BIS
Annex J-1(General-Insulated winding wires for use without interleaved insulation)	-	500	25 % discount to BIS
Annex J-2(Type tests)	-	500	25 % discount to BIS
Annex J-3(Testing during manufacturing)	-	500	25 % discount to BIS
Annex K-1(General- Safety interlocks)	-	500	25 % discount to BIS
Annex K-2(Components of the safety interlock safeguard mechanism)	-	500	25 % discount to BIS
Annex K-3(Inadvertent change of operating mode)	-	500	25 % discount to BIS
Annex K-4(Interlock safeguard override)	-	500	25 % discount to BIS
Annex K-5(Fail-safe)	-	500	25 % discount to BIS
Annex K-6(Mechanically operated safety interlocks)	-	500	25 % discount to BIS
Annex K-7(Interlock circuit isolation)	-	500	25 % discount to BIS
Annex L-1(General requirements)	-	500	25 % discount to BIS
Annex L-2(Permanently connected equipment)	-	500	25 % discount to BIS
Annex L-3()	-	500	25 % discount to BIS
Annex L-4(Single-phase equipment)	-	500	25 % discount to BIS
Annex L-5(Three-phase equipment)	-	500	25 % discount to BIS
Annex L-6(Switches as disconnect devices)	-	500	25 % discount to BIS
Annex L-7(Plugs as disconnect devices)	-	500	25 % discount to BIS
Annex L-8(Multiple power sources)	-	500	25 % discount to BIS
Annex L-9(Compliance criteria)	-	500	25 % discount to BIS
Annex M-1(General requirements)	-	500	25 % discount to BIS
Annex M-2(Safety of batteries and their cells)	-	500	25 % discount to BIS
Annex M-3(Protection circuits for batteries provided within the equipment)	-	500	25 % discount to BIS
Annex M-4(Additional safeguards for equipment containing a secondary lithium battery)	-	500	25 % discount to BIS
Annex M-5(Risk of burn due to short-circuit during carrying)	-	500	25 % discount to BIS
Annex M-6(Safeguards against short-circuits)	-	500	25 % discount to BIS
Annex M-7(Risk of explosion from lead acid and NiCd batteries)	-	500	25 % discount to BIS
Annex M-8("Protection against internal ignition from external spark sources of rechargeable batteries with aqueous electrolyte")	-	500	25 % discount to BIS
Annex M-9(Preventing electrolyte spillage)	-	500	25 % discount to BIS
Annex M-10(Instructions to prevent reasonably foreseeable misuse)	-	500	25 % discount to BIS
Annex N(Electrochemical potentials (V))	-	500	25 % discount to BIS
Annex O(Measurement of creepage distances and clearances)	-	500	25 % discount to BIS
Annex P-1(General-Safeguards against conductive objects)	-	500	25 % discount to BIS
Annex P-2(Safeguards against entry or consequences of entry of a foreign object)	-	500	25 % discount to BIS
Annex P-3(Safeguards against spillage of internal liquids)	-	500	25 % discount to BIS
Annex P-4(Metallized coatings and adhesives securing parts)	-	500	25 % discount to BIS
Annex Q-1(Limited power source)	-	500	25 % discount to BIS
Annex Q-2(Test for external circuits – paired conductor cable)	-	500	25 % discount to BIS
Annex R(Limited short-circuit test)	-	500	25 % discount to BIS
Annex S-1(Flammability test for fire enclosure and fire barrier materials of equipment where the steady state power does not exceed 4 000 W)	-	500	25 % discount to BIS
Annex S-2(Flammability test for fire enclosure and fire barrier integrity)	-	500	25 % discount to BIS
Annex S-3(Flammability tests for the bottom of a fire enclosure)	-	500	25 % discount to BIS
Annex S-4(Flammability classification of materials)	-	500	25 % discount to BIS
Annex S-5(Flammability test for fire enclosure materials of equipment with a steady state power exceeding 4 000 W)	-	500	25 % discount to BIS
Annex S-6(Grille covering material, cloth, and reticulated foam)	-	500	25 % discount to BIS
Annex T-1(General-Mechanical strength tests)	-	500	25 % discount to BIS
Annex T-2(Steady force test, 10 N)	-	500	25 % discount to BIS
Annex T-3(Steady force test, 30 N)	-	500	25 % discount to BIS
Annex T-4(Steady force test, 100 N)	-	500	25 % discount to BIS
Annex T-5(Steady force test, 250 N)	-	500	25 % discount to BIS
Annex T-6(Enclosure impact test)	-	500	25 % discount to BIS
Annex T-7(Drop test)	-	500	25 % discount to BIS
Annex T-8(Stress relief test)	-	500	25 % discount to BIS
Annex T-9(Glass impact test)	-	500	25 % discount to BIS
Annex T-10(Glass fragmentation test)	-	500	25 % discount to BIS
Annex T-11(Test for telescoping or rod antennas)	-	500	25 % discount to BIS
Annex V-1(Accessible parts of equipment)	-	500	25 % discount to BIS
Annex V-2(Accessible part criterion)	-	500	25 % discount to BIS
Annex W(Comparison of terms introduced in this document)	-	500	25 % discount to BIS
Annex X("Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420 V peak (300 V RMS)")	-	500	25 % discount to BIS
Annex Y-1(General- Construction requirements for outdoor enclosures)	-	500	25 % discount to BIS
Annex Y-3(Resistance to corrosion)	-	500	25 % discount to BIS
Annex Y-4(Gaskets)	-	500	25 % discount to BIS
Annex Y-5(Protection of equipment within an outdoor enclosure)	-	500	25 % discount to BIS
Annex Y-6(Mechanical strength of enclosures)	-	500	25 % discount to BIS
Annex H-2(Method A)	-	500	25 % discount to BIS

15 Jun, 2029

-
Included w.e.f. 03.06.2026 Exclusion: "Annex C-1 (Protection of materials in equipment from UV radiation) Annex C-2 (UV light conditioning test) Annex U (""Mechanical strength of CRTs and protection against the effects of implosion"") Annex Y-2 (Resistance to UV radiation) Cl-10.1 (General-Radiation) Cl-10.2 (Radiation energy source classifications) Cl-10.3 (Safeguards against laser radiation) Cl-10.4 (""Safeguards against optical radiation from lamps and lamp systems (including LED types)"") Cl-10.5 (Safeguards against X-radiation) Cl-10.6 (Safeguards against acoustic energy sources) "

IS 16102 (Part 1) (2026)

Self-Ballasted LED Lamps for General Lighting Services Part 1 Safety Requirements (First Revision)

Self-Ballasted LED Lamps for General Lighting Services Part 1 Safety Requirements

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirenents and General Test Requirements)	-	1000	-
Cl-6.1(Cap Interchangeability)	-	3000	-
Cl-6.2(Bending Moment and Mass Imparted by the Lamp at the Lamp Holder)	-	2000	-
Cl-7(Protection Against Accidental Contact with live parts)	-	3000	-
Cl-8.1(Insulation resistance and electric strength)	-	5000	-
Cl-8.2(Insulation Resistance lamp)	-	3000	-
Cl-8.3(Electric Strength)	-	3000	-
Cl-9.1(Mechanical Strength Requirements)	-	5000	-
Cl-9.2.1(Torsion Resistance of Unused Lamps)	-	3000	-
Cl-9.2.2(Torsion Resistance of Lamps after a Defined Time of Usage)	-	5000	-
Cl-9.2.3(Externally Applied Axial Pull and Bending Moment)	-	3000	-
Cl-9.3(Axial Strength of Edison Caps)	-	3000	-
Cl-10(Cap Temperature Rise)	-	5000	-
Cl-11(Resistance to Heat)	-	3000	-
Cl-12(Resistance to Flame and Ignition)	-	3000	-
Cl-13.1(Fault Conditions- General Requirements)	-	5000	-
Cl-14(Creepage Distance and Clearances)	-	3000	-
Cl-16(Test Conditions for Dimmable Lamps)	-	0	-
Cl-18(Ingress Protection Requirements)	-	4000	-
Cl-5(Marking)	-	2000	-
Cl-15(Abnormal Operation)	-	5000	-

15 Jun, 2029

-
Included w.e.f 27.07.2026 Exclusions: Cl-17.1 (UV Radiation) Cl-17.2 (Blue Light Hazard) Cl-19 (Information for luminaire design) Cl-20.3 (Accidentally Broken Lamps)

IS 10322 (Part 5/Sec 7) (2026)

Luminaires Part 5: Particular requirements Section 7: Lighting chains (Second Revision)

Luminaires Part 5 Particular Requirements Section 7 Lighting Chains

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-20.4(General test requirements)	-	1000	-
Cl-20.5.2(Protection against electric shock)	-	1000	-
Cl-20.6.1(Marking-General)	-	2000	-
Cl-20.6.2(Lighting chain marking)	-	500	-
Cl-20.6.3(Lighting chain and packaging marking)	-	500	-
Cl-20.6.4(Packaging or instructions marking)	-	500	-
Cl-20.7.1(Construction- General)	-	10000	-
Cl-20.7.2(Lampholders)	-	1000	-
Cl-20.7.4(Terminals and supply connections)	-	2000	-
Cl-20.7.5(Gaskets)	-	1000	-
Cl-20.7.6(Mechanical strength)	-	2000	-
Cl-20.7.7(Lamp bridging devices)	-	3000	-
Cl-20.7.8(Control units and controlgear)	-	1000	-
Cl-20.7.9(Lamp rotation)	-	1000	-
Cl-20.7.10(Lamp insertion and withdrawal force)	-	2000	-
Cl-20.7.11(Lamp mechanical requirements)	-	1000	-
Cl-20.7.12(Temporarily installed protected lighting (TPL) chains)	-	1000	-
Cl-20.8(Creepage distances and clearances)	-	3000	-
Cl-20.10(Terminals)	-	3000	-
Cl-20.11.2(Cables for lighting chains)	-	2000	-
Cl-20.11.3(Cord anchorage test)	-	2000	-
Cl-20.11.4(Plugs and cable length)	-	2000	-
Cl-20.11.5(Maximum length of extendable class II lighting chains)	-	1000	-
Cl-20.12(Protection against electric shock)	-	2000	-
Cl-20.12.2(Divisible plug)	-	1000	-
Cl-20.12.3(Electrification of decorations)	-	1000	-
Cl-20.12.4(Contacts of push-in lampholders)	-	1000	-
Cl-20.12.5(Blanking plugs)	-	1000	-
Cl-20.13.2(Test voltage)	-	7000	-
Cl-20.13.3(Lamp bridging devices)	-	2000	-
Cl-20.13.4(Short-circuit test of rectifier)	-	2000	-
Cl-20.14(Resistance to dust, solid objects and moisture)	-	7000	-
Cl-20.15(Insulation resistance and electric strength)	-	3000	-
Cl-20.16(Resistance to heat, fire and tracking)	-	5000	-

15 Jun, 2029

-
Included w.e.f 08.07.2026 Exclusions: Cl-20.7.1 (Construction- General)

IS 10322 (Part 5/Sec 6) (2026)

Luminaires Part 5: Particular requirements Section 6: Handlamps (First Revision)

Luminaires Part 5 Particular Requirements Section 6 Handlamps

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8.4(General test requirements)	-	1000	-
Cl-8.6(Marking)	-	3000	-
Cl-8.7(Construction)	-	10000	-
Cl-8.7.1(Handle of the handlamp)	-	1000	-
Cl-8.7.2(Lamp)	-	2000	-
Cl-8.7.4(Tungsten filament lamps)	-	1000	-
Cl-8.7.5(Flexible cable or cord)	-	3000	-
Cl-8.7.6(Mechanical strength)	-	3000	-
Cl-8.7.6.1(Translucent covers and protective covers)	-	3000	-
Cl-8.8(Creepage distances and clearances)	-	5000	-
Cl-8.10(Terminals)	-	5000	-
Cl-8.10.1(Terminals for supply connection)	-	1000	-
Cl-8.11(External and internal wiring)	-	3000	-
Cl-8.11.1(Rewirable handlamps)	-	1000	-
Cl-8.11.1(Non-rewirable handlamps)	-	1000	-
Cl-8.12(Protection against electric shock)	-	2000	-
Cl-8.13(Endurance tests and thermal tests)	-	12000	-
Cl-8.13.1(Endurance test)	-	10000	-
Cl-8.13.2(Thermal tests)	-	5000	-
Cl-8.13.3(Limiting temperature)	-	2000	-
Cl-8.14(Resistance to dust and moisture)	-	7000	-
Cl-8.15(Insulation resistance and electric strength)	-	3000	-
Cl-8.16(Resistance to heat, fire and tracking)	-	5000	-

15 Jun, 2029

-
Included w.e.f. 08.07.2026 Exclusion: Cl-8.7 (Construction)

IS 10322 (Part 5/Sec 4) (2026)

Luminaires Part 5: Particular requirements Section 4: Portable general purpose luminaires (First Revision)

Luminaires Part 5 Particular Requirements Section 4 Portable General Purpose Luminaires

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.4(General test requirements)	-	1000	-
Cl-4.6.1(Marking)	-	2000	-
Cl-4.6.2(Marking)	-	2000	-
Cl-4.7(Construction)	-	10000	-
Cl-4.7.1(Portable luminaires)	-	5000	-
Cl-4.7.2(Wiring)	-	5000	-
Cl-4.7.4(Candlestick luminaires)	-	2000	-
Cl-4.7.5(E5 lampholders)	-	2000	-
Cl-4.8(Creepage distances and clearances)	-	3000	-
Cl-4.9(Provision for earthing)	-	3000	-
Cl-4.10(Terminals)	-	5000	-
Cl-4.11(External and internal wiring)	-	5000	-
Cl-4.11.1(Cord anchorage)	-	3000	-
Cl-4.11.3(Flexible cable or cord)	-	3000	-
Cl-4.114(Non-detachable flexible cables or cords)	-	2000	-
Cl-4.12(Protection against electric shock)	-	2000	-
Cl-4.13(Endurance tests and thermal tests)	-	12000	-
Cl-4.14(Resistance to dust and moisture)	-	7000	-
Cl-4.15(Insulation resistance and electric strength)	-	3000	-
Cl-4.16(Resistance to heat, fire and tracking)	-	7000	-

15 Jun, 2029

-
Included w.e.f. 08.07.2026 Exclusion: Cl-4.7 (Construction)

IS 10322 (Part 5/Sec 5) (2026)

Luminaires Part 5: Particular requirements Section 5: Floodlights (Second Revision)

Luminaires Part 5 Particular Requirements Section 5 Floodlights

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.5(Marking)	-	1000	-
Cl-5.6(Construction)	-	10000	-
Cl-5.6.8.1(Protection by the use of glass that fractures into small pieces)	-	3000	-
5.6.8.2(Protection by the use of high impact resistant glass (high mechanical strength.))	-	3000	-
Cl-5.6.8.2.1(Thermal endurance test)	-	5000	-
Cl-5.7(Creepage distances and clearances)	-	3000	-
Cl-5.8(Provision for earthing)	-	3000	-
Cl-5.9(Terminals)	-	5000	-
Cl-5.10(External and internal wiring)	-	3000	-
Cl-5.11(Protection against electric shock)	-	3000	-
Cl-5.12(Endurance tests and thermal tests)	-	12000	-
Cl-5.13(Resistance to dust and moisture)	-	7000	-
Cl-5.14(Insulation resistance and electric strength)	-	3000	-
Cl-5.15(Resistance to heat, fire and tracking)	-	5000	-

15 Jun, 2029

-
Included w.e.f. 09.06.2026 Exclusion: Cl-5.6 (Construction) Photobiological Hazard

IS 10322 (Part 5/Sec 3) (2026)

Luminaires Part 5: Particular requirements Section 3: Luminaires for road and street lighting (Second Revision)

Luminaires Part 5 Particular Requirements Section 3 Luminaires for Road and Street Lighting

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.2(General test requirements)	-	1000	-
Cl-3.5(Marking)	-	2000	-
Cl-3.6.1(All luminaires)	-	15000	-
Cl-3.6.2(Luminaires for suspension on span wires)	-	2000	-
Cl-3.6.3(Luminaire or external part)	-	1000	-
Cl-3.6.4(Lampholders or optical part)	-	1000	-
Cl-3.6.5(Breaking glass (glass covers))	-	5000	-
Cl-3.6.5.2.1(high mechanical strength)	-	5000	-
Cl-3.7(Creepage distances and clearances)	-	3000	-
Cl-3.8(Provision for earthing)	-	3000	-
Cl-3.8.1(Fixed part of the terminal)	-	5000	-
Cl-3.9(Terminals)	-	3000	-
Cl-3.10(External and internal wiring)	-	3000	-
Cl-3.10.1(Road and street lighting)	-	3000	-
Cl-3.11(Protection against electric shock)	-	3000	-
Cl-3.12(Endurance tests and thermal tests)	-	12000	-
Cl-3.13(Resistance to dust and moisture)	-	7000	-
Cl-3.14(Insulation resistance and electric strength)	-	2000	-
Cl-3.15(Resistance to heat, fire and tracking)	-	5000	-
Cl-3.15(Resistance to heat, fire and tracking)	-	5000	-
Cl-3.15(Resistance to heat, fire and tracking)	-	5000	-
Cl-3.15(Resistance to heat, fire and tracking)	-	5000	-

15 Jun, 2029

-
Included w.e.f. 09.06.2026 Exclusion: Cl-3.6.1 (All luminaires) Photobiological Hazard

IS 10322 (Part 5/Sec 2) (2026)

Luminaires Part 5: Particular requirements Section 2: Recessed luminaires and recessed air-handling luminaires (Second Revision)

LUMINAIRES PART 5 PARTICULAR REQUIREMENTS SECTION 2 RECESSED LUMINAIRES AND RECESSED AIR-HANDLING LUMINAIRES

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-2.4(General test requirements)	-	1000	-
Cl-2.6.2(Marking)	-	2000	-
Cl-2.6.3(Marking)	-	2000	-
Cl-2.6.4(Marking)	-	2000	-
Cl-2.7(Construction)	-	15000	-
Cl-2.8(Creepage distances and clearances)	-	3000	-
Cl-2.9(Provision for earthing)	-	2000	-
Cl-2.10(Terminals)	-	3000	-
Cl-2.11(External and internal wiring)	-	3000	-
Cl-2.12(Protection against electric shock)	-	2000	-
Cl-2.13(Endurance tests and thermal tests)	-	15000	-
Cl-2.14(Resistance to dust and moisture)	-	5000	-
Cl-2.15(Insulation resistance and electric strength)	-	3000	-
Cl-2.16(Resistance to heat, fire and tracking)	-	5000	-

15 Jun, 2029

-
Included w.e.f. 08.07.2026 Exclusion: Cl-2.7 (Construction)

IS 10322 (Part 5/Sec 1) (2026)

Luminaires Part 5: Particular requirements Section 1: Fixed general purpose luminaires (Second Revision)

Luminaires Part 5 Particular Requirements Section 1 Fixed General Purpose Luminaires

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-1.4(General test requirements)	-	1000	-
Cl-1.6(Marking)	-	2000	-
Cl-1.7(Construction)	-	9000	-
Cl-1.8(Creepage distances and clearances)	-	3000	-
Cl-1.9(Provision for earthing)	-	2000	-
Cl-1.10(Terminals)	-	1000	-
Cl-1.11(External and internal wiring)	-	2000	-
Cl-1.13(Endurance tests and thermal tests)	-	12000	-
Cl-1.14(Resistance to dust, solid objects and moistur)	-	7000	-
Cl-1.15(" Insulation resistance and electric strength, touch current and protective conductor current")	-	3000	-
Cl-1.16(Resistance to heat, fire and tracking)	-	5000	-
Cl-1.12(Protection against electric shock)	-	2000	-
Cl-1.12(Protection against electric shock)	-	2000	-

15 Jun, 2029

-
Included w.e.f. 08.07.2026 Exclusion: Cl-1.7 (Construction)

IS 4289 : Part 2 (2000)

Flexible cables for lifts and other flexible connections - Specification: Part 2 pvc insulated circular cables

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor)	-	1000	-
5(Separator)	-	1000	-
6(Insulation)	-	1000	-
7(Central heart)	-	1000	-
8(Fillers)	-	1000	-
9(tape)	-	1000	-
10(braid)	-	1000	-
11(sheath)	-	1000	-
12(GENERAL DETAILS OF CONSTRUCTION)	-	1000	-
13(Construction- Conductor)	-	1000	-
14(Construction- Insulation)	-	1000	-
14.2(Thickness of Insulation)	-	2000	-
14.3(Tolerance on Thickness of Insulation)	-	2000	-
15(Core identification)	-	1000	-
16(Core assembly)	-	1000	-
17(overall covering)	-	1000	-
17.1.1(Thickness of Sheath)	-	2000	-
17.1.2(Tolerance on Thickness of Sheath)	-	2000	-
18.1.a.i(IS 10810 Part-1)	-	2000	-
18.1.a.ii(IS 10810 Part-5)	-	2000	-
18.1.b(IS 10810 Part-6)	-	2000	-
18.1.c.i(IS 10810 Part-7)	-	2000	-
18.1.c.i(IS 10810 Part-7)	-	2000	-
18.1.c.ii(IS 10810 Part-11)	-	2000	-
18.1.c.ii(IS 10810 Part-11)	-	2000	-
18.1.c.iii(IS 10810 Part-10)	-	2000	-
18.1.c.iii(IS 10810 Part-10)	-	2000	-
18.1.c.iv(IS 10810 Part-14)	-	2000	-
18.1.c.iv(IS 10810 Part-14)	-	2000	-
18.1.c.v(IS 10810 Part-12)	-	2000	-
18.1.c.v(IS 10810 Part-12)	-	2000	-
18.1.c.vi(IS 10810 Part-60)	-	2000	-
18.1.c.vi(IS 10810 Part-60)	-	2000	-
18.1.d(IS 10810 Part-45)	-	2000	-
18.1.e(IS 10810 Part-43)	-	2000	-
18.1. f(IS 10810 Part-54)	-	2000	-
18.1.g(IS 10810 Part-53)	-	2000	-
4(Conductor)	-	0	-
5(Separator)	-	0	-
6(Insulation)	-	0	-
7(Central heart)	-	0	-
8(Fillers)	-	0	-
9(tape)	-	0	-
10(braid)	-	0	-
11(sheath)	-	0	-
12(GENERAL DETAILS OF CONSTRUCTION)	-	0	-
13(Construction- Conductor)	-	0	-
14(Construction- Insulation)	-	0	-
14.2(Thickness of Insulation)	-	0	-
14.3(Tolerance on Thickness of Insulation)	-	0	-
15(Core identification)	-	0	-
16(Core assembly)	-	0	-
17(overall covering)	-	0	-
17.1.1(Thickness of Sheath)	-	0	-
17.1.2(Tolerance on Thickness of Sheath)	-	0	-
18.1.a.i(IS 10810 Part-1)	-	0	-
18.1.a.ii(IS 10810 Part-5)	-	0	-
18.1.b(IS 10810 Part-6)	-	0	-
18.1.c.i(IS 10810 Part-7)	-	0	-
18.1.c.i(IS 10810 Part-7)	-	0	-
18.1.c.ii(IS 10810 Part-11)	-	0	-
18.1.c.ii(IS 10810 Part-11)	-	0	-
18.1.c.iii(IS 10810 Part-10)	-	0	-
18.1.c.iii(IS 10810 Part-10)	-	0	-
18.1.c.iv(IS 10810 Part-14)	-	0	-
18.1.c.iv(IS 10810 Part-14)	-	0	-
18.1.c.v(IS 10810 Part-12)	-	0	-
18.1.c.v(IS 10810 Part-12)	-	0	-
18.1.c.vi(IS 10810 Part-60)	-	0	-
18.1.c.vi(IS 10810 Part-60)	-	0	-
18.1.d(IS 10810 Part-45)	-	0	-
18.1.e(IS 10810 Part-43)	-	0	-
18.1. f(IS 10810 Part-54)	-	0	-
18.1.g(IS 10810 Part-53)	-	0	-

15 Jun, 2029

-
Included w.e.f 01.04.2026

IS 4289 : Part 1 (1984)

Specification for flexible cables for lifts and other flexible connections: Part 1 elastomer insulated cables (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Conductor)	-	1000	-
4(Separator)	-	1000	-
5(Insulation)	-	1000	-
5(Central heart)	-	1000	-
7(Fillers)	-	1000	-
8(Proofed tape)	-	1000	-
9(Braid)	-	1000	-
10(Sheath)	-	1000	-
11(GENERAL DETAILS OF CONSTRUCTION)	-	1000	-
12(Conductor)	-	1000	-
13(Insulation)	-	1000	-
14(Core identification)	-	1000	-
15(Core assembly)	-	1000	-
16.1(Overall covering- sheathed cables)	-	1000	-
16.2(overall covering- braided cables)	-	1000	-
17.1.a(Persulphate test)	-	2000	-
17.1.b(Annealing test)	-	2000	-
17.1.c(Conductor resistance test)	-	2000	-
17.1.d(Test for thickness of insulation and sheath)	-	2000	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	2000	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	2000	-
17.1.e.2(Ageing in air oven for insulation)	-	2000	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	2000	-
17.1.f.2(Ageing in air bomb for sheath)	-	2000	-
17.1.f.3(Oil resistance for sheath)	-	2000	-
17.1.f.4(Tear resistance)	-	2000	-
17.1.g(High voltage water immersion test)	-	2000	-
17.1.h(Insulation resistance test)	-	2000	-
17.1.j(Static flexibility test)	-	2000	-
17.1.k(Flammability test)	-	2000	-
17.1.a(Persulphate test)	-	2000	-
17.1.b(Annealing test)	-	2000	-
17.1.c(Conductor resistance test)	-	2000	-
17.1.d(Test for thickness of insulation and sheath)	-	2000	-
17.1.e.1(Tensile strength and elongation at break for insulation)	-	2000	-
17.1.f.1(Tensile strength and elongation at break for Sheath)	-	2000	-
17.1.e.2(Ageing in air oven for insulation)	-	2000	-
17.1.e.3(Ageing in oxygen bomb for insulation)	-	2000	-
17.1.f.2(Ageing in air bomb for sheath)	-	2000	-
17.1.f.3(Oil resistance for sheath)	-	2000	-
17.1.f.4(Tear resistance)	-	2000	-
17.1.g(High voltage water immersion test)	-	2000	-
17.1.h(Insulation resistance test)	-	2000	-
17.1.j(Static flexibility test)	-	2000	-
17.1.k(Flammability test)	-	2000	-
17.1.a(IS 10810 Part-4)	-	2000	-
17.1.b(IS 10810 Part-1)	-	2000	-
17.1.c(IS 10810 Part-5)	-	2000	-
17.1.d(IS 10810 Part-6)	-	2000	-
17.1.e.1(IS 10810 Part-7)	-	2000	-
17.1.f.1(IS 10810 Part-7)	-	2000	-
17.1.e.2(IS 10810 Part-11)	-	2000	-
17.1.e.3(IS 10810 Part-56)	-	2000	-
17.1.f.2(IS 10810 Part-56)	-	2000	-
17.1.f.3(IS 10810 Part-31)	-	2000	-
17.1.f.4(IS 10810 Part-17)	-	2000	-
17.1.g(IS 10810 Part-45)	-	2000	-
17.1.h(IS 10810 Part-43)	-	2000	-
17.1.j(IS 10810 Part-54)	-	2000	-
17.1.k(IS 10810 Part-53)	-	2000	-
17.1.a(IS 10810 Part-4)	-	2000	-
17.1.b(IS 10810 Part-1)	-	2000	-
17.1.c(IS 10810 Part-5)	-	2000	-
17.1.d(IS 10810 Part-6)	-	2000	-
17.1.e.1(IS 10810 Part-7)	-	2000	-
17.1.f.1(IS 10810 Part-7)	-	2000	-
17.1.e.2(IS 10810 Part-11)	-	2000	-
17.1.e.3(IS 10810 Part-56)	-	2000	-
17.1.f.2(IS 10810 Part-56)	-	2000	-
17.1.f.3(IS 10810 Part-31)	-	2000	-
17.1.f.4(IS 10810 Part-17)	-	2000	-
17.1.g(IS 10810 Part-45)	-	2000	-
17.1.h(IS 10810 Part-43)	-	2000	-
17.1.j(IS 10810 Part-54)	-	2000	-
17.1.k(IS 10810 Part-53)	-	2000	-

15 Jun, 2029

-
Included w.e.f. 17.03.2026

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(S)	-	1000	-
4(P)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.00 to 2.24 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2.80 to 3.15 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Hard Core For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 For 2.00 to 2.24 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.80 to 3.15 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Soft Core)	-	1000	-
11(a) Size)	-	1000	-
11(b) Construction)	-	1000	-
11(c) tensile designation)	-	1000	-
11(d) lay)	-	1000	-
11(e) coating)	-	1000	-
11(f) length)	-	1000	-
11( g) mass)	-	1000	-
11(h) manufacturer's name or trade mark)	-	1000	-
11(i) lot number along with the order number)	-	1000	-
11(j) BIS Standards Mark)	-	1000	-
5(a) Grade)	-	1000	-
5(b) Tensile Grade)	-	1000	-
6(a) Lay)	-	1000	-
6(b) Construction)	-	1000	-
7(Freedom from defects)	-	1000	-
9(a) Tensile)	-	1000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
11(a) Size)	-	1000	-
11(b) Construction)	-	1000	-
11(c) tensile designation)	-	1000	-
11(d) lay)	-	1000	-
11(e) coating)	-	1000	-
11(f) length)	-	1000	-
11( g) mass)	-	1000	-
11(h) manufacturer's name or trade mark)	-	1000	-
11(i) lot number along with the order number)	-	1000	-
11(j) BIS Standards Mark)	-	1000	-
5(a) Grade)	-	1000	-
5(b) Tensile Grade)	-	1000	-
6(a) Lay)	-	1000	-
6(b) Construction)	-	1000	-
7(Freedom from defects)	-	1000	-
9(a) Tensile)	-	1000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
11(a) Size)	-	1000	-
11(b) Construction)	-	1000	-
11(c) tensile designation)	-	1000	-
11(d) lay)	-	1000	-
11(e) coating)	-	1000	-
11(f) length)	-	1000	-
11( g) mass)	-	1000	-
11(h) manufacturer's name or trade mark)	-	1000	-
11(i) lot number along with the order number)	-	1000	-
11(j) BIS Standards Mark)	-	1000	-
5(a) Grade)	-	1000	-
5(b) Tensile Grade)	-	1000	-
6(a) Lay)	-	1000	-
6(b) Construction)	-	1000	-
7(Freedom from defects)	-	1000	-
9(a) Tensile)	-	1000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
CL 8.2(AVG single wire dia (08))	-	1000	-
CL 8.2(AVG strand wire dia (08))	-	1000	-
4(S)	-	-	-
4(P)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.00 to 2.24 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2.80 to 3.15 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Hard Core For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Hard Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 For 2.00 to 2.24 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.80 to 3.15 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Soft Core)	-	-	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Soft Core)	-	-	-
11(a) Size)	-	-	-
11(b) Construction)	-	-	-
11(c) tensile designation)	-	-	-
11(d) lay)	-	-	-
11(e) coating)	-	-	-
11(f) length)	-	-	-
11( g) mass)	-	-	-
11(h) manufacturer's name or trade mark)	-	-	-
11(i) lot number along with the order number)	-	-	-
11(j) BIS Standards Mark)	-	-	-
5(a) Grade)	-	-	-
5(b) Tensile Grade)	-	-	-
6(a) Lay)	-	-	-
6(b) Construction)	-	-	-
7(Freedom from defects)	-	-	-
9(a) Tensile)	-	-	-
9(b) Elongation)	-	-	-
9(c) Galvanizing Test)	-	-	-
11(a) Size)	-	-	-
11(b) Construction)	-	-	-
11(c) tensile designation)	-	-	-
11(d) lay)	-	-	-
11(e) coating)	-	-	-
11(f) length)	-	-	-
11( g) mass)	-	-	-
11(h) manufacturer's name or trade mark)	-	-	-
11(i) lot number along with the order number)	-	-	-
11(j) BIS Standards Mark)	-	-	-
5(a) Grade)	-	-	-
5(b) Tensile Grade)	-	-	-
6(a) Lay)	-	-	-
6(b) Construction)	-	-	-
7(Freedom from defects)	-	-	-
9(a) Tensile)	-	-	-
9(b) Elongation)	-	-	-
9(c) Galvanizing Test)	-	-	-
11(a) Size)	-	-	-
11(b) Construction)	-	-	-
11(c) tensile designation)	-	-	-
11(d) lay)	-	-	-
11(e) coating)	-	-	-
11(f) length)	-	-	-
11( g) mass)	-	-	-
11(h) manufacturer's name or trade mark)	-	-	-
11(i) lot number along with the order number)	-	-	-
11(j) BIS Standards Mark)	-	-	-
5(a) Grade)	-	-	-
5(b) Tensile Grade)	-	-	-
6(a) Lay)	-	-	-
6(b) Construction)	-	-	-
7(Freedom from defects)	-	-	-
9(a) Tensile)	-	-	-
9(b) Elongation)	-	-	-
9(c) Galvanizing Test)	-	-	-
CL 8.2(AVG single wire dia (08))	-	-	-
CL 8.2(AVG strand wire dia (08))	-	-	-

15 Jun, 2029

-
Included w.e.f 24.02.2026

IS 398 : Part 2 (2025)

Aluminium Conductor for Overhead Transmission Purposes - Specification Part 2 Aluminium Conductors Galvanized Steel Reinforced (Fourth Revision)

120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Material)	-	1000	Rs. 16000/- (Up to 100 Sq.mm), Rs. 90000/- (150 Sq.mm to 200 Sq.mm), Rs. 120000/- (400 Sq.mm to 560 Sq.mm)
Cl-6.1.1(chemical composition of high carbon steel)	-	2000	-
Cl-6.2(zinc used for galvanizing)	-	2000	-
Cl-7(Freedom From Defects)	-	1000	-
Cl-8.1(Wires-Nominal Sizes)	-	2000	-
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	2000	-
Cl-9.1(Joint in Wires)	-	2000	-
Cl-9.2(Aluminium Wires)	-	2000	-
Cl-9.3(Galvanized Steel Wires)	-	2000	-
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	2000	-
Cl-13.3(Conductor- Visual examination)	-	1000	-
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	2000	-
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	5000	-
Cl- 13.14(Conductor- Ultimate tensile strength test on stranded conductor)	-	30000	-
Cl- 13.13(Conductor- Surface condition test on stranded conductor)	-	30000	-
Cl- 13.15(Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.))	-	0	-
Cl-13.16(Conductor- Radio interference voltage test)	-	0	-
Cl-13.4(Aluminium wires-Measurement of diameter)	-	2000	-
Cl- 13.6(Aluminium wires -Breaking load test)	-	2000	-
Cl- 13.8(Aluminium wires- Wrapping test)	-	2000	-
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	2000	-
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	2000	-
Cl- 13.4(Steel wires- Measurement of diameter)	-	2000	-
Cl- 13.6(Steel wires- Breaking load test)	-	2000	-
Cl- 13.7(Steel wires- Ductility test)	-	2000	-
Cl- 13.8(Steel wires- Wrapping test)	-	2000	-
Cl- 13.10(Steel wires- Galvanizing test)	-	2000	-
Cl-13.7.1(Torsion Test)	-	2000	-
Cl-13.7.2(Elongation Test)	-	2000	-
Cl-11.1(Standard Length)	-	2000	-
Cl-11.2(Random Lengths)	-	2000	-

15 Jun, 2029

-
Included w.e.f. 17.03.2026 Exclusion: Cl- 13.15 (Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.)) Cl-13.16 (Conductor- Radio interference voltage test)"

IS 12776 (2002)

Galvanized strand for earthing - Specification (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Freedom From Defects (IS 12776))	-	1000	-
5.3(Joints in wires (IS 12776))	-	1000	-
6- Annex-A, Sl-2(Size of the wire (IS 12776))	-	1000	-
6- Annex-A, Sl-8(Lay (IS 12776))	-	2000	-
8.1-Annex-A,Sl-9(Breaking Force of Strand (IS 12776))	-	3000	-
8.2-Annex-A,Sl-6(Elongation of wire, IS 10810(Part-37))	-	3000	-
8.2-Annex-A,Sl-3(Tensile Strength of wire IS 10810(Part-37))	-	3000	-
8.3-Annex-A,Sl-12(Resistance at 200 C (IS 12776))	-	3000	-
8.4(Wrapping Test (IS 12776))	-	2000	-
8.5-Annex-A-Sl-7a(Amount of zinc Coating (IS 6745))	-	2000	-
8.5-Annex-A-Sl-7b(Uniformity of Coating (IS 2633))	-	2000	-
8.5-Annex-A-Sl-4(Torsion Test IS 10810(Part-37))	-	2000	-
4.1(Carbon- IS 228(Part 1))	-	1000	-
4.1(Sulphur- IS 228(Part 9))	-	1000	-
4.1(Phosphorous- IS 228(Part 3))	-	1000	-
4.1(Manganese- IS 228(Part 2))	-	1000	-
4.1(Silicon- IS 228(Part 8))	-	1000	-
6- Annex-A, Sl-8(Lay Length)	-	2000	-

15 Jun, 2029

-
Included w.e.f. 17.03.2026

IS 16246 (2015)

Elastomer insulated cables with limited circuit integrity when affected by fire - Specification

85000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1( Cables for Fixed Installation)	-	1000	-
Cl.5( INSULATION)	-	1000	-
Cl. 6.1( Glass Tape)	-	1000	-
Cl 6.2( Polyethylene Teraphthalate (PETP) or Polypropylene base Tape)	-	1000	-
Cl 6.4( Fire Barrier Tape)	-	1000	-
Cl 7(CENTRE AND FILLERS)	-	1000	-
Cl 7(CENTRE AND FILLERS)	-	1000	-
Cl 7(CENTRE AND FILLERS)	-	1000	-
Cl 7(CENTRE AND FILLERS)	-	1000	-
Cl 8( ARMOUR)	-	1000	-
Cl 9.1( Inner Sheath)	-	1000	-
Cl 9.2( Outer Sheath)	-	1000	-
Cl 10.1( CONDUCTORS)	-	1000	-
Cl 10.2( CONDUCTORS)	-	1000	-
Cl 11.1( INSULATION)	-	1000	-
Cl 11.2(Thickness of Insulation IS 10810 : Part 6)	-	2000	-
Cl 12( CORE IDENTIFICATION)	-	1000	-
Cl 13( LAYING UP OF CORES)	-	1000	-
Cl 14.2( Thickness of Inner Sheath IS 10810 : Part 6)	-	2000	-
Cl 15.1( ARMOURING)	-	1000	-
Cl 15.3.1( Type of Armour)	-	1000	-
Cl 15.3.2( Type of Armour)	-	1000	-
Cl 15.3.3( ARMOURING)	-	1000	-
Cl 15.3.3( ARMOURING)	-	1000	-
Cl 15.4.1( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 16.2( OUTER SHEATH)	-	1000	-
Cl 16.3( Thickness of Outer Sheath - Avg IS 10810 : Part 6)	-	2000	-
Cl 16.3( Thickness of Outer Sheath - Minimum IS 10810 : Part 6)	-	2000	-
Cl 17.2(Annealing test (for copper) IS 10810 : Part 1)	-	2000	-
Cl 17.2(Conductor resistance test IS 10810 : Part 5)	-	2000	-
Cl 17.1(Persulphate test (tinned copper conductor) IS 10810 : Part 4)	-	2000	-
Cl 17.2(Tensile strength before ageing on insulation IS 10810 : Part 7)	-	2000	-
Cl 17.2(elongation at break before ageing on insulation IS 10810 : Part 7)	-	2000	-
Cl 17.2(Tensile strength after Ageing in air bomb IS 10810 : Part 56)	-	3000	-
Cl 17.2(Elongation after Ageing in air bomb IS 10810 : Part 56)	-	3000	-
Cl 17.2(Tensile strength variation)	-	3000	-
Cl 17.2(Elongation Variation)	-	3000	-
Cl 17.2(Hot set elongation on insulation IS 10810 : Part 30)	-	3000	-
Cl 17.2(Permanent elongation (set) on insulation IS 10810 : Part 30)	-	3000	-
Cl 17.1(Tensile strength before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(elongation at break before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(Hot set elongation test on sheath IS 10810 : Part 30)	-	3000	-
Cl 17.1(Permanent elongation (set) test on sheath IS 10810 : Part 30)	-	3000	-
Cl 17.1(Oxygen index test on sheath IS 10810 : Part 58)	-	5000	-
Cl 17.1(Temperature index test on sheath IS 10810 : Part 64)	-	5000	-
Cl 17.1(Acid gas generation on sheath IS 10810 : Part 39)	-	5000	-
Cl 17.2(Insulation resistance test IS 10810 : Part 43)	-	2000	-
Cl 17.1(Water absorption test (for insulation) IS 10810 : Part 28)	-	5000	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2000	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2000	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	10000	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	10000	-
Cl 18.4.1( Flame Retardence Test on Single Cable IS 10810 : Part 61)	-	2000	-
Cl 18.4.2(Flame Retardence Test on Bunched Cables IS 10810 : Part 63)	-	10000	-
Cl 19.1( Manufacturer’s Identification)	-	1000	-
Cl 19.2( Voltage Identification)	-	1000	-
Cl 19.3( Cable Identification)	-	1000	-
Cl 19.4( Cable Code)	-	1000	-

15 Jun, 2029

-
Included w.e.f. 17.03.2026

IS 9968 : Part 1 (2025)

Elastomer Insulated Cables - Specification Part 1 for Working Voltages up to and including 1100 volts (Second Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Copper Conductor)	-	1000	-
Cl-4.2(Aluminum Conductor)	-	1000	-
Cl-6.1(Proofed Tape)	-	1000	-
Cl-6.2("Polyethylene Terephthalate (PETP) Tape or Plastic Tape or Any Other Suitable Tape")	-	1000	-
Cl-6.3(Glass Tape)	-	1000	-
Cl-7(Fillers)	-	1000	-
Cl-8.1(Textile Braid)	-	1000	-
Cl-8.2(Glass Braid)	-	1000	-
Cl-9.1(General Service Insulated Cables and Flexible Cords)	-	1000	-
Cl-9.2(Heat Resisting Insulated Cables)	-	1000	-
Cl-9.3(Silicon Rubber Insulated Cable)	-	1000	-
Cl-10.1(Preservative Compound)	-	1000	-
Cl-10.2(Varnish)	-	1000	-
Cl-12(separator tape)	-	1000	-
Cl-14(Core Identification)	-	1000	-
Cl-18(Laying UP of Cores)	-	1000	-
Cl-19(Binder Tape)	-	1000	-
Cl-20.2(Thickness of Sheath)	-	2000	-
Cl-20.3(Tolerance on Thickness of Sheath)	-	2000	-
Cl-20.4(Colour)	-	1000	-
Cl-22.1 (i) (a)(Conductor resistance test)	-	2000	-
Cl-22.1 (i) (b)(High voltage test or spark test.)	-	2000	-
Cl-22.1 (ii) (a)(Annealing test (for copper);)	-	2000	-
Cl-22.1 (ii) (b)(Tensile Test ((for aluminium);)	-	2000	-
Cl-22.1 (ii) (c)(Wrapping test (for aluminium);)	-	2000	-
Cl-22.1 (ii) (f)(Tensile strength and elongation at break of insulation and sheath)	-	2000	-
Cl-22.1 (ii) (g)(Hot set test for insulation and sheath)	-	2000	-
Cl-22.1 (ii) (h)(High voltage test)	-	2000	-
Cl-22.1 (ii) (i)(Insulation resistance test)	-	2000	-
Cl-22.1 (iii) (a)(Persulphate test (for tinned copper);)	-	2000	-
Cl-22.1 (iii) (f)(Test for thickness of insulation and sheath and overall diameter)	-	2000	-
Electrical(Tensile strength and elongation at break)	-	3000	-
Cl-22.1 (iii) (g), 2(Ageing in air oven)	-	3000	-
Cl-22.1 (iii) (g), 3(Ageing in air bomb)	-	3000	-
Cl-22.1 (iii) (g), 4(Ageing In oxygen bomb)	-	3000	-
Cl-22.1 (iii) (g), 5(Hot set)	-	2000	-
Cl-22.1 (iii) (g), 6(Oil resistance;)	-	2000	-
Cl-22.1 (iii) (g), 7(Tear resistance)	-	2000	-
Cl-22.1 (iii) (i)(High voltage (water immersion) test;)	-	2000	-
Cl-22.1 (iii) (j)(Flammability test)	-	2000	-
Cl-22.1 (iii) (k)(Water absorption test (for insulation as applicable))	-	5000	-
Cl-24.1(Manufacturer’s Identification)	-	1000	-
Cl-25(Packing and Morning)	-	1000	-

15 Jun, 2029

-
Included w.e.f. 10.02.2026

IS 7098 : Part 1 (2025)

Crosslinked Polyethylene Insulated Thermoplastic Sheathed Cables - Specification Part 1 For Working Voltages up to and Including 1 100 Volts (Second Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Conductors -Material)	-	1000	-
Cl-5, Table-1 (i)(Tensile strength)	-	1000	-
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	2000	-
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	2000	-
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	2000	-
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	2000	-
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	2000	-
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	2000	-
Cl-5, Table-1 (iv)(Shrinkage)	-	1000	-
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	5000	-
Cl-5, Table-1 (vi)(Volume resistivity)	-	2000	-
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	1000	-
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	1000	-
Cl-7(Armouring)	-	1000	-
Cl-8(Outer Sheath)	-	1000	-
Cl-10.3(Tolerance on Thickness of Insulation)	-	2000	-
Cl-11(Core Identification)	-	1000	-
Cl-12(Laying up of Cores)	-	1000	-
Cl-13(Inner Sheath (Common Covering))	-	1000	-
Cl-14.1(Armouring- Application)	-	1000	-
Cl-14.1.2(armour round wires/formed wires)	-	1000	-
Cl-14.2(Type of Armour)	-	1000	-
Cl-14.3(Dimensions)	-	2000	-
Cl-14.4(Joints)	-	2000	-
Cl-14.5(Resistance)	-	2000	-
Cl-15.3(Thickness of Outer Sheath)	-	2000	-
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	1000	-
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	1000	-
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	1000	-
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	2000	-
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	2000	-
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	2000	-
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	2000	-
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	2000	-
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	2000	-
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	2000	-
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	2000	-
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	2000	-
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	3000	-
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	3000	-
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	3000	-
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	2000	-
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	2000	-
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	1000	-
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	2000	-
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	2000	-
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	5000	-
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	2000	-
Cl-17.2(High voltage test)	-	5000	-
Cl-17.3(Flammability test)	-	2000	-
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	5000	-
Cl-17.5(Flame retardance test on single cable)	-	2000	-
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	10000	-
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	2000	-
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	5000	-
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	5000	-
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	5000	-
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	5000	-
Cl-16.4 (i)(Cold bend test for outer sheath)	-	2000	-
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	2000	-
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	2000	-
Cl. 9(Conductor - Regarding Construction Compliance)	-	1000	-
Cl. 10.4(Application of Insulation)	-	1000	-
Cl. 13.3(Thickness of Inner sheath)	-	2000	-
Cl. 15.1(Application of Outer sheath)	-	1000	-
Cl. 15.2(Clour of Outer sheath)	-	1000	-

15 Jun, 2029

-
Included w.e.f. 10.02.2026

IS 4246 (2025)

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION (Sixth Revision )

DOMESTIC GAS STOVE AND BUILT IN HOB FOR USE WITH LPG SPECIFICATION

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General - IS 4246 : 2025)	-	500	-
4.1(General - IS 4246 : 2025)	-	0	-
4.1.1(General - IS 4246 : 2025)	-	0	-
5(Materials - Cl. 5 of IS 5116)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1(Materials - IS 5116)	-	0	-
5.1(Materials - IS 5116)	-	0	-
5.1.1(Materials - IS 5116)	-	0	-
5.2(Materials - IS 5116)	-	500	-
5.2(Materials - IS 5116)	-	0	-
5.3(Materials - IS 5116)	-	500	-
5.5(Materials - IS 5116)	-	500	-
5.5(Materials - IS 5116)	-	0	-
5.5(Materials - IS 5116)	-	0	-
5.7(Materials - IS 5116)	-	500	-
6.1(Design for Maintainance)	-	500	-
6.1(Design for Maintainance)	-	0	-
6.2(Design for Maintainance)	-	500	-
6.2(Design for Maintainance)	-	500	-
6.3(Design for Maintainance)	-	500	-
6.4(Design for Maintainance)	-	500	-
6.5(Design for Maintainance)	-	500	-
6.6(Design for Maintainance)	-	500	-
7.0(Rigidity and Stability)	-	500	-
7.1(Rigidity and Stability)	-	500	-
7.2(Rigidity and Stability)	-	500	-
7.3(Rigidity and Stability)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.2(Workmanship and Finish -)	-	500	-
8.3(Workmanship and Finish -)	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
10(Injector Jets)	-	500	-
10(Injector Jets)	-	0	-
10(Injector Jets)	-	0	-
10(Injector Jets)	-	0	-
10(Injector Jets)	-	0	-
10(Injector Jets)	-	0	-
11.1(Burners- Cl. 10 of IS 5116)	-	500	-
11.1(Burners- Cl. 10 of IS 5116)	-	0	-
11.1(Burners- Cl. 10 of IS 5116)	-	0	-
11.1(Burners- Cl. 10 of IS 5116)	-	0	-
11.1(Burners- Cl. 10 of IS 5116)	-	0	-
11.2(Burners)	-	500	-
11.3(Burners)	-	500	-
11.4(Burners)	-	500	-
12.1(Burner Pan Support)	-	500	-
12.2(Burner Pan Support)	-	500	-
12.3(Burner Pan Support)	-	0	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	1000	-
13,2(Gas Soundness Test)	-	1000	-
13.2(Gas Leak Detector)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	500	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.2(Gas Inlet Connection)	-	0	-
14.2(Gas Inlet Connection)	-	500	-
14.2(Gas Inlet Connection)	-	0	-
14.2(Gas Inlet Connection)	-	0	-
14.3(Gas Inlet Connection)	-	500	-
14.4(Gas Inlet Connection)	-	500	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	500	-
14.6(Gas Inlet Connection)	-	500	-
15.0(Strength and Rigidity)	-	500	-
15.0(Strength and Rigidity)	-	0	-
15.0(Strength and Rigidity)	-	0	-
15.0(Strength and Rigidity)	-	0	-
17.0(Gas Consumption Test)	-	5000	-
17.0(Gas Consumption Test)	-	5000	-
17.0(Gas Consumption Test)	-	0	-
17.0(Gas Consumption Test)	-	0	-
17.0(Gas Consumption Test)	-	0	-
17.0(Gas Consumption Test)	-	0	-
17.2(Gas Consumption Test - For Gas Stoves)	-	5000	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	0	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	0	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	0	-
17.3(Gas Consumption Test - For Built in Hobs)	-	5000	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	5000	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	5000	-
18.1(Ignition and Flame Travel)	-	500	-
18.1(Ignition and Flame Travel)	-	0	-
18.2(Ignition and Flame Travel)	-	500	-
18.3(Ignition and Flame Travel)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	500	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	0	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	0	-
19.1(Flame Stability)	-	1000	-
19.1.1(Flame Stability)	-	1000	-
19.2(Flame Stability)	-	500	-
19.3(Flame Stability)	-	500	-
20(Noise Control)	-	500	-
21(Flash Back)	-	500	-
22(Formation of Soot)	-	500	-
23(Resistance to Draught)	-	500	-
24.1(Combustion)	-	1000	-
24.1(Combustion)	-	0	-
24.2(Combustion)	-	0	-
25.1(Fire Hazard and Limiting Temperatures)	-	2000	-
25.1(Fire Hazard and Limiting Temperatures)	-	2000	-
25.1(Fire Hazard and Limiting Temperatures)	-	0	-
25.1(Fire Hazard and Limiting Temperatures)	-	0	-
25.2(Fire Hazard and Limiting Temperatures)	-	0	-
26.1(Thermal Efficiency- Gas Stoves)	-	5000	-
26.1(Thermal Efficiency- Gas Stoves)	-	5000	-
26.1(Thermal Efficiency- Gas Stoves)	-	0	-
26.1(Thermal Efficiency- Gas Stoves)	-	0	-
26.1(Thermal Efficiency- Gas Stoves)	-	0	-
26.2(Thermal Efficiency- For Built in Hobs)	-	5000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	5000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	5000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	5000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	5000	-
5.1.1(Materials - IS 5116)	-	1000	-
4.1(General - IS 4246 : 2025)	-	500	-
4.1(General - IS 4246 : 2025)	-	0	-
4.1.1(General - IS 4246 : 2025)	-	0	-
5(Materials - Cl. 5 of IS 5116)	-	500	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1.1(Materials - Toughened glass, if provided,)	-	0	-
5.1(Materials - IS 5116)	-	0	-
5.1(Materials - IS 5116)	-	0	-
5.1.1(Materials - IS 5116)	-	0	-
5.2(Materials - IS 5116)	-	500	-
5.2(Materials - IS 5116)	-	0	-
5.3(Materials - IS 5116)	-	500	-
5.5(Materials - IS 5116)	-	0	-
5.5(Materials - IS 5116)	-	500	-
5.5(Materials - IS 5116)	-	0	-
5.7(Materials - IS 5116)	-	500	-
6.1(Design for Maintainance)	-	500	-
6.1(Design for Maintainance)	-	0	-
6.2(Design for Maintainance)	-	0	-
6.2(Design for Maintainance)	-	0	-
6.3(Design for Maintainance)	-	500	-
6.4(Design for Maintainance)	-	500	-
6.5(Design for Maintainance)	-	500	-
6.6(Design for Maintainance)	-	500	-
7.0(Rigidity and Stability)	-	500	-
7.1(Rigidity and Stability)	-	500	-
7.2(Rigidity and Stability)	-	500	-
7.3(Rigidity and Stability)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	500	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.1(Workmanship and Finish - Cl. 7 of IS 5116)	-	0	-
8.2(Workmanship and Finish -)	-	0	-
8.3(Workmanship and Finish -)	-	500	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	1000	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
9(Gas Taps- Cl. 8 of IS 5116 (Except 8.7 and 8.11.1))	-	0	-
10(Injector Jets)	-	1000	-
10(Injector Jets)	-	0	-
10(Injector Jets)	-	0	-
10(Injector Jets)	-	0	-
10(Injector Jets)	-	0	-
10(Injector Jets)	-	0	-
11.1(Burners- Cl. 10 of IS 5116)	-	500	-
11.1(Burners- Cl. 10 of IS 5116)	-	0	-
11.1(Burners- Cl. 10 of IS 5116)	-	0	-
11.1(Burners- Cl. 10 of IS 5116)	-	0	-
11.1(Burners- Cl. 10 of IS 5116)	-	0	-
11.2(Burners)	-	500	-
11.3(Burners)	-	500	-
11.4(Burners)	-	500	-
12.1(Burner Pan Support)	-	500	-
12.2(Burner Pan Support)	-	0	-
12.3(Burner Pan Support)	-	0	-
13.1(Gas Soundness Test - Cl. 16 of IS 5116)	-	1000	-
13,2(Gas Soundness Test)	-	1000	-
13.2(Gas Leak Detector)	-	1000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	1000	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.1(Gas Inlet Connection - Cl. 18 of IS 5116)	-	0	-
14.2(Gas Inlet Connection)	-	500	-
14.2(Gas Inlet Connection)	-	0	-
14.2(Gas Inlet Connection)	-	0	-
14.2(Gas Inlet Connection)	-	0	-
14.3(Gas Inlet Connection)	-	500	-
14.4(Gas Inlet Connection)	-	500	-
14.5(Gas Inlet Connection - Cl. 17.3 of IS 5116)	-	500	-
14.6(Gas Inlet Connection)	-	500	-
15.0(Strength and Rigidity)	-	500	-
15.0(Strength and Rigidity)	-	0	-
15.0(Strength and Rigidity)	-	0	-
15.0(Strength and Rigidity)	-	0	-
17.0(Gas Consumption Test)	-	5000	-
17.0(Gas Consumption Test)	-	0	-
17.0(Gas Consumption Test)	-	0	-
17.0(Gas Consumption Test)	-	0	-
17.0(Gas Consumption Test)	-	0	-
17.0(Gas Consumption Test)	-	0	-
17.2(Gas Consumption Test - For Gas Stoves)	-	5000	-
17.2 (a)(Gas Consumption Test - For Gas Stoves)	-	0	-
17.2 (b)(Gas Consumption Test - For Gas Stoves)	-	0	-
17.2 (c)(Gas Consumption Test - For Gas Stoves)	-	0	-
17.3(Gas Consumption Test - For Built in Hobs)	-	5000	-
17.3.1(Gas Consumption Test - For Built in Hobs)	-	0	-
17.3.2(Gas Consumption Test - For Built in Hobs)	-	0	-
18.1(Ignition and Flame Travel)	-	500	-
18.1(Ignition and Flame Travel)	-	500	-
18.2(Ignition and Flame Travel)	-	0	-
18.3(Ignition and Flame Travel)	-	0	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	0	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	0	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	0	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	0	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	0	-
18.4(Ignition and Flame Travel - Cl. 14 of IS 5116)	-	0	-
19.1(Flame Stability)	-	500	-
19.1.1(Flame Stability)	-	0	-
19.2(Flame Stability)	-	0	-
19.3(Flame Stability)	-	0	-
20(Noise Control)	-	1000	-
21(Flash Back)	-	500	-
22(Formation of Soot)	-	500	-
23(Resistance to Draught)	-	500	-
24.1(Combustion)	-	500	-
24.1(Combustion)	-	0	-
24.2(Combustion)	-	0	-
25.1(Fire Hazard and Limiting Temperatures)	-	500	-
25.1(Fire Hazard and Limiting Temperatures)	-	0	-
25.1(Fire Hazard and Limiting Temperatures)	-	0	-
25.1(Fire Hazard and Limiting Temperatures)	-	0	-
25.2(Fire Hazard and Limiting Temperatures)	-	0	-
26.1(Thermal Efficiency- Gas Stoves)	-	5000	-
26.1(Thermal Efficiency- Gas Stoves)	-	0	-
26.1(Thermal Efficiency- Gas Stoves)	-	0	-
26.1(Thermal Efficiency- Gas Stoves)	-	0	-
26.1(Thermal Efficiency- Gas Stoves)	-	0	-
26.2(Thermal Efficiency- For Built in Hobs)	-	5000	-
26.2(Thermal Efficiency- For Built in Hobs)	-	0	-
26.2(Thermal Efficiency- For Built in Hobs)	-	0	-
26.2(Thermal Efficiency- For Built in Hobs)	-	0	-
26.2(Thermal Efficiency- For Built in Hobs)	-	0	-
5.1.1(Materials - IS 5116)	-	1000	-

15 Jun, 2029

-
Included w.e.f. 17.03.2026

IS 16103 : Part 1 (2025)

LED Modules for General Lighting Part 1 Safety Specifications (First Revision)

LED Modules for General Lighting

32000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Marking)	-	1000	-
Cl-7.1(Integral terminals)	-	2000	-
Cl-7.2(Terminals other than integral terminals)	-	2000	-
Cl-8(Earthing)	-	2000	-
Cl-9(Protection against accidental contact with live parts)	-	1000	-
Cl-10(Moisture resistance and insulation)	-	5000	-
Cl-11(Electric strength)	-	1000	-
Cl-12.1(Fault conditions- General)	-	2000	-
Cl-12.2(Overpower condition)	-	2000	-
Cl-15(Creepage distances and clearances)	-	2000	-
Cl-16(Screws, current-carrying parts and connections)	-	2000	-
Cl-17(Resistance to heat, fire and tracking)	-	5000	-
Cl-18(Resistance to corrosion)	-	3000	-
Cl-20.1(Heat management- General)	-	500	-
Cl-20.2(Thermal interface material)	-	1000	-
Cl-20.3(Heat protection)	-	3000	-
Cl-19(Information for luminaire design)	-	500	-
Cl-13(Conformity testing during manufacture)	-	500	-
Cl-6(Marking)	-	1000	-
Cl-7.1(Integral terminals)	-	2000	-
Cl-7.2(Terminals other than integral terminals)	-	2000	-
Cl-8(Earthing)	-	2000	-
Cl-9(Protection against accidental contact with live parts)	-	1000	-
Cl-10(Moisture resistance and insulation)	-	5000	-
Cl-11(Electric strength)	-	1000	-
Cl-12.1(Fault conditions- General)	-	2000	-
Cl-12.2(Overpower condition)	-	2000	-
Cl-15(Creepage distances and clearances)	-	2000	-
Cl-16(Screws, current-carrying parts and connections)	-	2000	-
Cl-17(Resistance to heat, fire and tracking)	-	5000	-
Cl-18(Resistance to corrosion)	-	3000	-
Cl-20.1(Heat management- General)	-	500	-
Cl-20.2(Thermal interface material)	-	1000	-
Cl-20.3(Heat protection)	-	3000	-
Cl-19(Information for luminaire design)	-	500	-
Cl-13(Conformity testing during manufacture)	-	500	-

15 Jun, 2029

-
Included w.e.f. 17.02.2026 Exclusion: Cl-21.1 (UV radiation), Cl-21.2 (Blue light hazard)

IS 374 (2019)

Specification for electric ceiling type fans and regulators (Third Revision)

Specification for electric ceiling type fans and regula

34000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	0	-
8.1(Marking (as per Cl. 7 of IS 302-2-80:2017))	-	500	-
8.1,a(Marking )	-	0	-
8.1,b(Marking )	-	0	-
8.1,c(Marking )	-	0	-
8.1,d(Marking )	-	0	-
8.1,e(Marking )	-	0	-
8.1,f(Marking )	-	0	-
8.1,g(Marking )	-	0	-
8.2(Marking )	-	0	-
8.3,a(Marking )	-	0	-
8.3,b(Marking )	-	0	-
8.3,c(Marking )	-	0	-
8.3,d(Marking )	-	0	-
8.3,e(Marking )	-	0	-
8.4(Marking )	-	0	-
8(Marking (as per Cl. 7.1 of IS 302-2-80:2017))	-	0	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008))	-	0	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008))	-	0	-
8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017))	-	0	-
6.2(Rating)	-	0	-
9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017))	-	1000	-
9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017))	-	1000	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	2000	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	1000	-
9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017))	-	1000	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	2500	-
9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017))	-	500	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	2000	-
9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017))	-	500	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	1000	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017))	-	0	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	0	-
9(Construction (as per Cl.22.101 of IS 302-2-80 :2017))	-	2000	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	1000	-
9(Components (as per Cl.24.103 of IS 302-2-80 :2017))	-	500	-
9(Components (as per Cl.24.104 of IS 302-2-80 :2017))	-	0	-
9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017))	-	1000	-
9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017))	-	1000	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	1000	-
9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017))	-	1000	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	1000	-
9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017))	-	2000	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	500	-
10.1(Speed Regulators)	-	1000	-
10.2(Speed Regulators)	-	0	-
10.3(Speed Regulators)	-	0	-
10.4(Speed Regulators)	-	0	-
10.5(Speed Regulators)	-	0	-
10.6(Speed Regulators)	-	0	-
10.7(Speed Regulators)	-	0	-
10.8(Speed Regulators)	-	0	-
11.1(Starting)	-	500	-
11.2(Starting)	-	0	-
12(Interchangeability)	-	500	-
13(Silent Operation)	-	500	-
14.3 & Table 1(Test for Air Performance)	-	2000	-
14.4(Measurement of Speed of the Fan )	-	1000	-
14.5(Measurement of Power factor and Power Input)	-	500	-
16(Endurance Test)	-	3000	-
17(Test for Harmonic Distortion)	-	1000	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	500	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	500	-
(Cl. 32 of IS 302-1: 2008)(Radiation, toxicity and similar hazards)	-	500	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	0	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	0	-
(Cl. 32 of IS 302-1: 2008)(Radiation, toxicity and similar hazards)	-	0	-

15 Jun, 2029

-
-

IS 11951 (2024)

PUMPSET FOR DIRECT EVAPORATIVE AIR COOLER â SPECIFICATION (Second Revision)

PUMPSET FOR DIRECT EVAPORATIVE AIR COOLER SPECIFICATION

44500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Non-Submersible Pumpset)	-	1000	-
5.1.2(Submersible Pumpset)	-	1000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Discharge Head, m)	-	2000	-
6.1, 7.3, 9.1, 9.4.2,Table-1(Minimum Discharge, l/min)	-	2000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 1 Motor Wattage)	-	2000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 2 Motor Wattage)	-	2000	-
6.1, 7.3, 9.1,9.4.2, Table-2(Minimum Discharge Head, Hd)	-	2000	-
6.1, 7.3, 9.1, 9.4.2,Table-2(Discharge Measurement Height, h)	-	5000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Minimum, Discharge*)	-	5000	-
Cl-8(GENERAL REQUIREMENTS)	-	2000	-
9.2(Tests on motor)	-	2000	-
9.3(Water Requirement)	-	2000	-
9.4.1(Reliability Tests)	-	2000	-
9.4.3(Ingress protection test)	-	2000	-
9.4.6(Dry Run Test)	-	2000	-
9.5(Routine Test)	-	2000	-
9.6(Type Test)	-	2000	-
9.7(Leakage current and electric strength at operating temperature)	-	2000	-
9.7(Moisture resistance)	-	2000	-
9.7(Leakage current and electric strength)	-	1000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Motor Wattage)	-	1000	-
5.1.1(Non-Submersible Pumpset)	-	1000	-
5.1.2(Submersible Pumpset)	-	1000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Discharge Head, m)	-	2000	-
6.1, 7.3, 9.1, 9.4.2,Table-1(Minimum Discharge, l/min)	-	2000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 1 Motor Wattage)	-	2000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 2 Motor Wattage)	-	2000	-
6.1, 7.3, 9.1,9.4.2, Table-2(Minimum Discharge Head, Hd)	-	2000	-
6.1, 7.3, 9.1, 9.4.2,Table-2(Discharge Measurement Height, h)	-	5000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Minimum, Discharge*)	-	5000	-
Cl-8(GENERAL REQUIREMENTS)	-	2000	-
9.2(Tests on motor)	-	2000	-
9.3(Water Requirement)	-	2000	-
9.4.1(Reliability Tests)	-	2000	-
9.4.3(Ingress protection test)	-	2000	-
9.4.6(Dry Run Test)	-	2000	-
9.5(Routine Test)	-	2000	-
9.6(Type Test)	-	2000	-
9.7(Leakage current and electric strength at operating temperature)	-	2000	-
9.7(Moisture resistance)	-	2000	-
9.7(Leakage current and electric strength)	-	1000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Motor Wattage)	-	1000	-
5.1.1(Non-Submersible Pumpset)	-	1000	-
5.1.2(Submersible Pumpset)	-	1000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Discharge Head, m)	-	2000	-
6.1, 7.3, 9.1, 9.4.2,Table-1(Minimum Discharge, l/min)	-	2000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 1 Motor Wattage)	-	2000	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 2 Motor Wattage)	-	2000	-
6.1, 7.3, 9.1,9.4.2, Table-2(Minimum Discharge Head, Hd)	-	2000	-
6.1, 7.3, 9.1, 9.4.2,Table-2(Discharge Measurement Height, h)	-	5000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Minimum, Discharge*)	-	5000	-
Cl-8(GENERAL REQUIREMENTS)	-	2000	-
9.2(Tests on motor)	-	2000	-
9.3(Water Requirement)	-	2000	-
9.4.1(Reliability Tests)	-	2000	-
9.4.3(Ingress protection test)	-	2000	-
9.4.6(Dry Run Test)	-	2000	-
9.5(Routine Test)	-	2000	-
9.6(Type Test)	-	2000	-
9.7(Leakage current and electric strength at operating temperature)	-	2000	-
9.7(Moisture resistance)	-	2000	-
9.7(Leakage current and electric strength)	-	1000	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Motor Wattage)	-	1000	-
5.1.1(Non-Submersible Pumpset)	-	0	-
5.1.2(Submersible Pumpset)	-	0	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Discharge Head, m)	-	0	-
6.1, 7.3, 9.1, 9.4.2,Table-1(Minimum Discharge, l/min)	-	0	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 1 Motor Wattage)	-	0	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 2 Motor Wattage)	-	0	-
6.1, 7.3, 9.1,9.4.2, Table-2(Minimum Discharge Head, Hd)	-	0	-
6.1, 7.3, 9.1, 9.4.2,Table-2(Discharge Measurement Height, h)	-	0	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Minimum, Discharge*)	-	0	-
Cl-8(GENERAL REQUIREMENTS)	-	0	-
9.2(Tests on motor)	-	0	-
9.3(Water Requirement)	-	0	-
9.4.1(Reliability Tests)	-	0	-
9.4.3(Ingress protection test)	-	0	-
9.4.6(Dry Run Test)	-	0	-
9.5(Routine Test)	-	0	-
9.6(Type Test)	-	0	-
9.7(Leakage current and electric strength at operating temperature)	-	0	-
9.7(Moisture resistance)	-	0	-
9.7(Leakage current and electric strength)	-	0	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Motor Wattage)	-	0	-
5.1.1(Non-Submersible Pumpset)	-	500	-
5.1.2(Submersible Pumpset)	-	500	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Discharge Head, m)	-	500	-
6.1, 7.3, 9.1, 9.4.2,Table-1(Minimum Discharge, l/min)	-	500	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 1 Motor Wattage)	-	500	-
6.1, 7.3, 9.1, 9.4.2, Table-1(Type 2 Motor Wattage)	-	500	-
6.1, 7.3, 9.1,9.4.2, Table-2(Minimum Discharge Head, Hd)	-	500	-
6.1, 7.3, 9.1, 9.4.2,Table-2(Discharge Measurement Height, h)	-	500	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Minimum, Discharge*)	-	500	-
Cl-8(GENERAL REQUIREMENTS)	-	500	-
9.2(Tests on motor)	-	500	-
9.3(Water Requirement)	-	500	-
9.4.1(Reliability Tests)	-	500	-
9.4.3(Ingress protection test)	-	500	-
9.4.6(Dry Run Test)	-	500	-
9.5(Routine Test)	-	500	-
9.6(Type Test)	-	500	-
9.7(Leakage current and electric strength at operating temperature)	-	500	-
9.7(Moisture resistance)	-	500	-
9.7(Leakage current and electric strength)	-	500	-
6.1, 7.3, 9.1, 9.4.2, Table-2(Motor Wattage)	-	500	-

15 Jun, 2029

-
included w.e.f 09-12-2025.

IS 302 : Part 2 : Sec 3 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 3 Electric Irons (Second Revision)

Household and Similar Electrical Appliances Safety Part 2 Particular Requirements Section 3 Electric Irons (Second Revision)

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General requirement)	-	500	-
Cl-7(Marking and instructions)	-	500	-
Cl-8(Protection against access to live parts)	-	500	-
Cl-10(Power input and current)	-	1000	-
Cl-11(Heating)	-	1000	-
Cl-12(Charging of metal-ion batteries)	-	2000	-
Cl-13(Leakage current and electric strength at operating temperature)	-	500	-
Cl-14(Transient overvoltages)	-	1000	-
Cl-15(Moisture resistance)	-	500	-
Cl-16(Leakage current and electric strength)	-	500	-
Cl-17(Overload protection of transformers and associated circuits)	-	500	-
Cl-18(Endurance)	-	1000	-
Cl-19(Abnormal operation)	-	2000	-
Cl-20(Stability and mechanical hazards)	-	500	-
Cl-21(Mechanical strength)	-	500	-
Cl-22(Construction)	-	2000	-
Cl-23(Internal wiring)	-	500	-
Cl-24(Components)	-	500	-
Cl-25(Supply connection and external flexible cords)	-	500	-
Cl-26(Terminals for external conductors)	-	500	-
Cl-27(Provision for earthing)	-	500	-
Cl-28(Screws and connections)	-	500	-
Cl-29(Clearances, creepage distances and solid insulation)	-	500	-
Cl-30(Resistance to heat and fire)	-	1000	-
Cl-31(Resistance to rusting)	-	1000	-
Cl-32(Radiation, toxicity and similar hazards)	-	500	-

15 Jun, 2029

-
included w.e.f 09-12-2025.

IS 16242 : Part 1 (2025)

Uninterruptible power systems UPS Part 1 Safety requirements (first revision)

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Fault and abnormal conditions)	-	1000	10% Discount for BIS
Cl-4.3(Short-circuit and overload protection)	-	500	10% Discount for BIS
Cl-4.3.101(AC input current)	-	1100	10% Discount for BIS
Cl-4.3.102(Transformer protection)	-	500	10% Discount for BIS
Cl-4.3.103(AC input short-circuit current)	-	500	10% Discount for BIS
Cl-4.3.104(Protection of the energy storage device)	-	500	10% Discount for BIS
Cl-4.3.105(Unsynchronised load transfer)	-	1000	10% Discount for BIS
Cl-4.4(Protection against electric shock)	-	500	10% Discount for BIS
Cl-4.4.2.2.2(Selection tables for contact area and skin humidity condition)	-	500	10% Discount for BIS
Cl-4.4.3.3(Protection by means of enclosures or barriers- Openings)	-	500	10% Discount for BIS
Cl-4.4.7.1.1(Influencing factors)	-	500	10% Discount for BIS
Cl-4.4.7.1.2(Pollution degree)	-	500	10% Discount for BIS
Cl-4.4.7.1.3(Overvoltage category (OVC))	-	1000	10% Discount for BIS
Cl-4.4.7.7(PWB spacings for functional insulation)	-	500	10% Discount for BIS
Cl-4.4.9(Capacitor discharge)	-	500	10% Discount for BIS
Cl-4.5.2(Service access areas)	-	500	10% Discount for BIS
Cl-4.6(Protection against fire and thermal hazards)	-	500	10% Discount for BIS
Cl-4.6.2.2(Components within a circuit representing a fire hazard)	-	500	10% Discount for BIS
Cl-4.6.3.1(General)	-	500	10% Discount for BIS
Cl-4.6.3.2(Flammability of enclosure materials)	-	500	10% Discount for BIS
Cl-4.6.3.3.2(Openings in the top and side of fire enclosures)	-	500	10% Discount for BIS
Cl-4.6.4.1(Temperature limits- Internal parts)	-	500	10% Discount for BIS
Cl- 4.6.5(Limited power sources)	-	500	10% Discount for BIS
Cl-4.7(Protection against mechanical hazards)	-	500	10% Discount for BIS
Clause 4(Protection against hazards)	-	500	10% Discount for BIS
Cl-4.7.101(Protection in service access area)	-	500	10% Discount for BIS
Clause 5(Test requirements)	-	500	10% Discount for BIS
Cl-4.8 .101(Equipment with multiple sources of supply- General)	-	500	10% Discount for BIS
Clause 5.2.2(Mechanical tests)	-	500	10% Discount for BIS
Clause 5.2.3(Electrical tests)	-	500	10% Discount for BIS
Cl-4.9(Protection against environmental stresses)	-	500	10% Discount for BIS
Cl-4.10(Protection against sonic pressure hazards)	-	500	10% Discount for BIS
Clause 5.2.4("Abnormal operation tests")	-	1000	10% Discount for BIS
Cl-4.11(Wiring and connections)	-	500	10% Discount for BIS
Clause 5.2.5(Material tests)	-	500	10% Discount for BIS
Clause 5.2.6(Environmental tests)	-	1500	10% Discount for BIS
Cl-4.11.101.1(Non-detachable cords- Cord guard)	-	500	10% Discount for BIS
Clause 5.2.7(Hydrostatic pressure test)	-	500	10% Discount for BIS
Cl-4.11.101.2(Cord anchorages and strain relief)	-	500	10% Discount for BIS
Clause 6(Information and marking requirements)	-	500	10% Discount for BIS
Cl-4.101.1(Emergency switching (disconnect) device)	-	500	10% Discount for BIS
Clause 6.1.101(Durability)	-	500	10% Discount for BIS
Cl-4.101.2(Normal disconnect devices)	-	500	10% Discount for BIS
Cl-4.102.1(Stored energy source- General)	-	500	10% Discount for BIS
Cl-4.102.2(Accessibility and maintainability)	-	500	10% Discount for BIS
Cl-4.102.3(Distance between battery cells)	-	500	10% Discount for BIS
Cl- 4.102.5(Electrolyte spillage)	-	500	10% Discount for BIS
Cl- 4.102.6(Ventilation and hydrogen concentration)	-	500	10% Discount for BIS
Cl- 4.102.8.1(Overcurrent and earth fault protection)	-	500	10% Discount for BIS
Cl- 4.102.8.2(Location of protective devices)	-	500	10% Discount for BIS
Cl-4.102.8.3(Rating of protective devices)	-	500	10% Discount for BIS
Cl-4.103(UPS connection to telecommunication lines)	-	500	10% Discount for BIS
Cl-5.1.5.3(Operating parameters for tests)	-	500	10% Discount for BIS
Cl-5.1.7(Test overview)	-	500	10% Discount for BIS
Cl-5.2.2.2(Non-accessibility test)	-	500	10% Discount for BIS
Cl-5.2.2.4.4(Drop test)	-	500	10% Discount for BIS
Cl-4.8.102(Backfeed protection)	-	500	10% Discount for BIS
Cl- 4.102.7(Charging voltages)	-	1000	10% Discount for BIS
Cl-5.2.2.6.101(Wall or ceiling mounted equipment test)	-	1000	10% Discount for BIS
Cl-5.2.2.6.102(Rack mounted equipment test)	-	500	10% Discount for BIS
Cl-5.2.2.101(Cord guard test)	-	500	10% Discount for BIS
Cl-5.2.3.9(Limited power source test)	-	500	10% Discount for BIS
Cl-5.2.3.10(Temperature rise test)	-	500	10% Discount for BIS
Cl-5.2.3.101.1(Backfeed protection test- General)	-	2000	10% Discount for BIS
Cl-5.2.3.101.2(Test for pluggable UPS)	-	500	10% Discount for BIS
Cl-5.2.3.101.3(Test for permanently connected UPS)	-	500	10% Discount for BIS
Cl-5.2.3.101.4(Method to simulate the load-induced change of reference potential for pluggable UPS)	-	500	10% Discount for BIS
Cl-5.2.3.101.5(Solid-state backfeed protection)	-	500	10% Discount for BIS
Cl-5.2.3.102(Input current test)	-	500	10% Discount for BIS
Cl-5.2.3.103(Short-time withstand current test)	-	500	10% Discount for BIS
Cl-5.2.3103.3(Input port short-time withstand current rating)	-	500	10% Discount for BIS
Cl-5.2.3.104(Transformer protection test)	-	500	10% Discount for BIS
Cl- 5.2.3.105(Unsynchronised load transfer test)	-	500	10% Discount for BIS
Cl-5.2.4.1(Abnormal operation and simulated faults tests- General)	-	1000	10% Discount for BIS
Cl-5.2.6.4(Vibration test)	-	3000	10% Discount for BIS
Cl-5.2.6.5(Salt mist test)	-	2700	10% Discount for BIS
Cl-5.2.6.6(Dust and sand test)	-	2500	10% Discount for BIS
Cl-6(Information and marking requirements)	-	100	10% Discount for BIS
Cl-4.2(Fault and abnormal conditions)	-	500	10% Discount for BIS
Cl-4.3(Short-circuit and overload protection)	-	500	10% Discount for BIS
Cl-4.3.101(AC input current)	-	500	10% Discount for BIS
Cl-4.3.102(Transformer protection)	-	500	10% Discount for BIS
Cl-4.3.103(AC input short-circuit current)	-	500	10% Discount for BIS
Cl-4.3.104(Protection of the energy storage device)	-	500	10% Discount for BIS
Cl-4.3.105(Unsynchronised load transfer)	-	500	10% Discount for BIS
Cl-4.4(Protection against electric shock)	-	500	10% Discount for BIS
Cl-4.4.2.2.2(Selection tables for contact area and skin humidity condition)	-	500	10% Discount for BIS
Cl-4.4.3.3(Protection by means of enclosures or barriers- Openings)	-	500	10% Discount for BIS
Cl-4.4.7.1.1(Influencing factors)	-	500	10% Discount for BIS
Cl-4.4.7.1.2(Pollution degree)	-	500	10% Discount for BIS
Cl-4.4.7.1.3(Overvoltage category (OVC))	-	500	10% Discount for BIS
Cl-4.4.7.7(PWB spacings for functional insulation)	-	500	10% Discount for BIS
Cl-4.4.9(Capacitor discharge)	-	500	10% Discount for BIS
Cl-4.5.2(Service access areas)	-	500	10% Discount for BIS
Cl-4.6(Protection against fire and thermal hazards)	-	500	10% Discount for BIS
Cl-4.6.2.2(Components within a circuit representing a fire hazard)	-	500	10% Discount for BIS
Cl-4.6.3.1(General)	-	500	10% Discount for BIS
Cl-4.6.3.2(Flammability of enclosure materials)	-	500	10% Discount for BIS
Cl-4.6.3.3.2(Openings in the top and side of fire enclosures)	-	500	10% Discount for BIS
Cl-4.6.4.1(Temperature limits- Internal parts)	-	500	10% Discount for BIS
Cl- 4.6.5(Limited power sources)	-	500	10% Discount for BIS
Cl-4.7(Protection against mechanical hazards)	-	500	10% Discount for BIS
Clause 4(Protection against hazards)	-	500	10% Discount for BIS
Cl-4.7.101(Protection in service access area)	-	500	10% Discount for BIS
Clause 5(Test requirements)	-	500	10% Discount for BIS
Cl-4.8 .101(Equipment with multiple sources of supply- General)	-	500	10% Discount for BIS
Clause 5.2.2(Mechanical tests)	-	500	10% Discount for BIS
Clause 5.2.3(Electrical tests)	-	500	10% Discount for BIS
Cl-4.9(Protection against environmental stresses)	-	500	10% Discount for BIS
Cl-4.10(Protection against sonic pressure hazards)	-	500	10% Discount for BIS
Clause 5.2.4("Abnormal operation tests")	-	500	10% Discount for BIS
Cl-4.11(Wiring and connections)	-	500	10% Discount for BIS
Clause 5.2.5(Material tests)	-	500	10% Discount for BIS
Clause 5.2.6(Environmental tests)	-	2000	10% Discount for BIS
Cl-4.11.101.1(Non-detachable cords- Cord guard)	-	500	10% Discount for BIS
Clause 5.2.7(Hydrostatic pressure test)	-	500	10% Discount for BIS
Cl-4.11.101.2(Cord anchorages and strain relief)	-	500	10% Discount for BIS
Clause 6(Information and marking requirements)	-	500	10% Discount for BIS
Cl-4.101.1(Emergency switching (disconnect) device)	-	500	10% Discount for BIS
Clause 6.1.101(Durability)	-	500	10% Discount for BIS
Cl-4.101.2(Normal disconnect devices)	-	500	10% Discount for BIS
Cl-4.102.1(Stored energy source- General)	-	400	10% Discount for BIS
Cl-4.102.2(Accessibility and maintainability)	-	500	10% Discount for BIS
Cl-4.102.3(Distance between battery cells)	-	500	10% Discount for BIS
Cl- 4.102.5(Electrolyte spillage)	-	500	10% Discount for BIS
Cl- 4.102.6(Ventilation and hydrogen concentration)	-	500	10% Discount for BIS
Cl- 4.102.8.1(Overcurrent and earth fault protection)	-	500	10% Discount for BIS
Cl- 4.102.8.2(Location of protective devices)	-	500	10% Discount for BIS
Cl-4.102.8.3(Rating of protective devices)	-	500	10% Discount for BIS
Cl-4.103(UPS connection to telecommunication lines)	-	500	10% Discount for BIS
Cl-5.1.5.3(Operating parameters for tests)	-	500	10% Discount for BIS
Cl-5.1.7(Test overview)	-	500	10% Discount for BIS
Cl-5.2.2.2(Non-accessibility test)	-	500	10% Discount for BIS
Cl-5.2.2.4.4(Drop test)	-	500	10% Discount for BIS
Cl-4.8.102(Backfeed protection)	-	500	10% Discount for BIS
Cl- 4.102.7(Charging voltages)	-	2000	10% Discount for BIS
Cl-5.2.2.6.101(Wall or ceiling mounted equipment test)	-	500	10% Discount for BIS
Cl-5.2.2.6.102(Rack mounted equipment test)	-	500	10% Discount for BIS
Cl-5.2.2.101(Cord guard test)	-	500	10% Discount for BIS
Cl-5.2.3.9(Limited power source test)	-	500	10% Discount for BIS
Cl-5.2.3.10(Temperature rise test)	-	1000	10% Discount for BIS
Cl-5.2.3.101.1(Backfeed protection test- General)	-	500	10% Discount for BIS
Cl-5.2.3.101.2(Test for pluggable UPS)	-	500	10% Discount for BIS
Cl-5.2.3.101.3(Test for permanently connected UPS)	-	500	10% Discount for BIS
Cl-5.2.3.101.4(Method to simulate the load-induced change of reference potential for pluggable UPS)	-	500	10% Discount for BIS
Cl-5.2.3.101.5(Solid-state backfeed protection)	-	500	10% Discount for BIS
Cl-5.2.3.102(Input current test)	-	500	10% Discount for BIS
Cl-5.2.3.103(Short-time withstand current test)	-	500	10% Discount for BIS
Cl-5.2.3103.3(Input port short-time withstand current rating)	-	500	10% Discount for BIS
Cl-5.2.3.104(Transformer protection test)	-	500	10% Discount for BIS
Cl- 5.2.3.105(Unsynchronised load transfer test)	-	500	10% Discount for BIS
Cl-5.2.4.1(Abnormal operation and simulated faults tests- General)	-	500	10% Discount for BIS
Cl-5.2.6.4(Vibration test)	-	3000	10% Discount for BIS
Cl-5.2.6.5(Salt mist test)	-	2500	10% Discount for BIS
Cl-5.2.6.6(Dust and sand test)	-	2500	10% Discount for BIS
Cl-6(Information and marking requirements)	-	500	10% Discount for BIS

15 Jun, 2029

-
included w.e.f 09-12-2025.

IS 11037 (2019)

Electronic Type Fan Regulators — Specification ( First Revision )

25500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1 (a)(Marking )	-	0	-
9.1 (b)(Marking )	-	0	-
9.1 (c)(Marking )	-	0	-
9.1 (d)(Marking )	-	0	-
9.1 (e)(Marking )	-	0	-
9.1 (f)(Marking )	-	0	-
9.2(Marking )	-	0	-
6.1(Design and General Construction)	-	200	-
6.2(Design and General Construction)	-	200	-
6.3(Design and General Construction)	-	200	-
6.5(Design and General Construction)	-	200	-
6.6(Design and General Construction)	-	200	-
9.5.1 , 7.3(Temperature Rise)	-	200	-
9.5.1 , 7.3 (a)(Temperature Rise )	-	500	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	500	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	500	-
9.5.2, 7.2(Leakage Current Test(as per Cl.13.2 of IS 302 (Part 1).)	-	500	-
9.5.3(High Voltage Test)	-	500	-
9.5.5(Earthing Connection)	-	500	-
9.5.6(Protection against electric shock (as per Cl.8 of IS 302 (Part 1))	-	500	-
7.7(Voltage drop)	-	500	-
8.1(Performance)	-	500	-
8.2(Performance)	-	500	-
8.3(Performance)	-	500	-
9.5.7, 9.5.4(Moisture Resistance )	-	500	-
7.4.1(a)(Mechanical strength )	-	500	-
7.4.1(b)(Mechanical strength )	-	500	-
9.5.8, (Mechanical strength (as per Cl.21.1 of IS 302-1:2008))	-	500	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	200	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	200	-
9.5.10( Electrical Endurance Test)	-	1000	-
9.5.11.2(Environmental Tests)	-	1000	-
9.5.11.3(Environmental Tests)	-	1000	-
9.5.11.4(Environmental Tests)	-	1000	-
9.5.12(Resistance to Abnormal Heat and to Fire)	-	500	-
9.5.12.1(Resistance to Abnormal Heat and to Fire)	-	500	-
9.5.13(Resistance to Rusting )	-	500	-
9.5.14(Checking of Dimensions)	-	200	-
7.1, 7.5.4(Insulation Resistance)	-	200	-
7.6(General and safety requirements)	-	100	-
9.1(Marking )	-	0	-
9.1 (a)(Marking )	-	0	-
9.1 (b)(Marking )	-	0	-
9.1 (c)(Marking )	-	0	-
9.1 (d)(Marking )	-	0	-
9.1 (e)(Marking )	-	0	-
9.1 (f)(Marking )	-	0	-
9.2(Marking )	-	0	-
6.1(Design and General Construction)	-	200	-
6.2(Design and General Construction)	-	200	-
6.3(Design and General Construction)	-	200	-
9.5.1 , 7.3(Temperature Rise)	-	200	-
9.5.1 , 7.3 (a)(Temperature Rise )	-	500	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	500	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	500	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	500	-
9.5.2, 7.2(Leakage Current Test(as per Cl.13.2 of IS 302 (Part 1).)	-	500	-
9.5.3(High Voltage Test)	-	500	-
9.5.5(Earthing Connection)	-	500	-
9.5.6(Protection against electric shock (as per Cl.8 of IS 302 (Part 1))	-	500	-
7.6(General and safety requirements)	-	1000	-
7.7(Voltage drop)	-	500	-
8.1(Performance)	-	500	-
8.2(Performance)	-	500	-
8.3(Performance)	-	500	-
9.5.7, 9.5.4(Moisture Resistance )	-	500	-
7.4.1(Mechanical strength )	-	500	-
7.4.1(a)(Mechanical strength )	-	500	-
7.4.1(b)(Mechanical strength )	-	500	-
9.5.8, (Mechanical strength (as per Cl.21.1 of IS 302-1:2008))	-	500	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	200	-
9.5.9, 7.5, Table-1(Creepage Distances and Clearances (as per Cl. 29 of IS 302-1))	-	200	-
9.5.10( Electrical Endurance Test)	-	1000	-
9.5.11.2(Environmental Tests)	-	1000	-
9.5.11.3(Environmental Tests)	-	1000	-
9.5.11.4(Environmental Tests)	-	1000	-
6.6(Design and General Construction)	-	100	-
6.5(Design and General Construction)	-	100	-
9.5.14(Checking of Dimensions)	-	100	-
9.5.13(Resistance to Rusting )	-	500	-
9.5.12.1(Resistance to Abnormal Heat and to Fire)	-	500	-
9.5.12(Resistance to Abnormal Heat and to Fire)	-	200	-
9.5.1 , 7.3 (b)(Temperature Rise)	-	100	-

15 Jun, 2029

-
Included w.e.f 04.11.2025

IS 3315 (2024)

Direct Evaporative Air Cooler â Specification (Fourth Revision)

Direct Evaporative Air Cooler Specification (Fourth Revision)

60000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Enclosure)	-	2000	-
Cl-5.2(Filter Pads)	-	2000	-
Cl-5.3(Sump Tank Capacities)	-	2000	-
Cl-5.4(Blower/Fan)	-	2000	-
Cl-5.4.3(Fan motor)	-	2000	-
Cl-5.5(Pump Set)	-	2000	-
Cl-5.6.1(Electrical wiring and connection)	-	2000	-
Cl-6(Rating Requirement)	-	2000	-
Cl-8.1(Performance Requirement)	-	5000	-
Cl-8.2(Sound Test)	-	2000	-
Cl-8.3(Air Delivery (Air Flow) Test)	-	6000	-
Cl-8.4(Cooling Efficiency Test)	-	6000	-
Cl-8.5(Power Consumption)	-	5000	-
Cl-8.6(EER Calculation Method)	-	5000	-
Cl-8.7(Drop Test)	-	2000	-
Cl-8.8(Air Cooler Blower/Fan Reliability Test)	-	3000	-
Cl-12.2.1(General Running Tests)	-	1000	-
Cl-12.2.2(Protection against Electric Shock)	-	1000	-
Cl-12.2.3(High Voltage Tests)	-	1000	-
Cl-12.2.4(Leakage Current)	-	1000	-
Cl-12.2.5(Provision for Earthing)	-	1000	-
Cl-12.2.6(Finish)	-	1000	-
Cl-13(Additional Requirement for ECO-Mark)	-	1000	-
Cl-14(Storage)	-	1000	-
Cl-5.6.2(Suitable power cable)	-	1000	-
Cl-5.7(Switches)	-	1000	-

15 Jun, 2029

-
Included w.e.f 04.11.2025

IS 996 (2025)

SINGLE PHASE ac INDUCTION MOTORS FOR GENERAL PURPOSE (Fouth Revision)

SINGLE PHASE ac INDUCTION MOTORS FOR GENERAL PURPOSE

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7(Dimensions)	-	1000	-
Cl-9.1(Mounting)	-	1000	-
Cl-9.2(Terminal Box)	-	1000	-
Cl-9.3(Mounting Constructions)	-	1000	-
Cl-9.4(Constructional Features)	-	1000	-
Cl-9.5(Earthing)	-	1000	-
Cl-10.1(Enclosures)	-	2000	-
Cl-12.1(Torques)	-	2000	-
Cl-12.1.2(Momentary overload test)	-	2000	-
Cl-12.2(Temperature Rise)	-	2000	-
Cl-12.3(Short Time Rating)	-	1000	-
Cl-12.4(Method of Testing)	-	1000	-
Cl-12.5(Performance Values)	-	2000	-
Cl-12.6(Limits of Vibration Severity)	-	1000	-
Cl-12.7(Insulation Resistance)	-	1500	-
Cl-13.1(High Voltage Values)	-	1500	-
Cl-13.2(Moisture Proofness)	-	2000	-
Cl-13.3(Leakage Current)	-	1000	-
Cl-14(Winding Resistance Measurement)	-	1000	-
Cl-15(REDUCED VOLTAGE RUNNING UP TEST AT NO LOAD)	-	1000	-
Cl-16(NOISE LEVEL)	-	1000	-
Cl-17(OVER SPEED TEST)	-	1000	-
Cl-18(TERMINAL MARKING)	-	500	-
Cl-12.1.1(Test for torues at rated voltage and frequency)	-	2000	-
Cl-12.1.1(Pull up Torque at rated voltage and frequency)	-	2000	-
Cl-12.1.1(Test for breakaway starting current at rated voltage and frequency)	-	2000	-
Cl-12.1.2(Breakaway (starting) torque at rated voltage and frequency)	-	2000	-
Cl-12.5.1(Test for full-load performance at rated voltage and frequency)	-	2000	-
Cl-21.5(Acceptance Tests)	-	2000	-
Cl-9.3(Mounting Constructions)	-	1000	-

15 Jun, 2029

-
Included w.e.f.29.09.2025

IS 14927 : Part 2 (2001)

Cable Trunking and Ducting Systems for Electrical Installations : Part 2 Cable Trunking and Ducting Systems Intended for Mounting on Walls or Ceiling

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	500	-
7.1(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7.1(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7.1(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7.1(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7.2(Marking (as per Cl 7.2 of IS:14927(Pt-I ):2001))	-	0	-
8.1( Dimensions (As per cl.8.1 of IS 14927(Pt-1) : 2001))	-	500	-
8.2(Dimensions (As per cl.8.2 of IS 14927(Pt-1) : 2001)	-	0	-
8.3, table 2( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
8.3, table 2( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
8.3, table 2( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
9.1(Construction ( As per Cl. 9.1 of IS 14927(Pt-1):2001))	-	500	-
9.1(Construction)	-	0	-
9.2(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-	0	-
9.2(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-	0	-
9.2(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-	0	-
9.2(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-	0	-
9.3(Construction ( As per Cl. 9.3 of IS 14927(Pt-1):2001))	-	0	-
9.3.1(Construction ( As per Cl. 9.3.1 of IS 14927(Pt-1):2001))	-	500	-
9.3.2, table 3(Construction ( As per Cl. 9.3.2, Table-3 of IS 14927(Pt-1):2001))	-	0	-
9.4.1(Construction [Access to Live Parts (As per Cl. 9.4.1 of IS 14927(Pt-1):2001)])	-	0	-
9.5(Construction (As per Cl. 9.5 of IS 14927(Pt-1):2001))	-	0	-
9.6.2(Construction [Membranes (As per Cl.9.6.2 of IS: 14927 (Pt-1):2001)])	-	500	-
9.6.4(Construction [Membranes (As per Cl.9.6.4 of IS: 14927 (Pt-1):2001)])	-	0	-
9.7.2, table 4(Construction [Glands (As per Cl.9.7.2 and Table-4 of IS: 14927 (Pt-1):2001)] )	-	0	-
10(Mechanical Properties )	-	500	-
10.2(Cable supporting test for Surface mounting (As per Cl.10.2))	-	500	-
10.2(Cable supporting test for Surface mounting (As per Cl.10.2))	-	0	-
10.2(Cable supporting test for Surface mounting (As per Cl.10.2))	-	0	-
10.2(Cable supporting test for Surface mounting (As per Cl.10.2))	-	0	-
10.2(Cable supporting test for Surface mounting (As per Cl.10.2))	-	0	-
10.2.3(Cable supporting test for Surface mounting (As per Cl.10.2.3))	-	0	-
10.2.3(Cable supporting test for Surface mounting (As per Cl.10.2.3))	-	0	-
10.2.3(Cable supporting test for Surface mounting (As per Cl.10.2.3))	-	0	-
10.2.3(Cable supporting test for Surface mounting (As per Cl.10.2.3))	-	0	-
10.3(Impact Test [ Cl.10.3 ])	-	500	-
10.3.4(Impact Test (As per Cl. 10.3.4 of IS: 14927(Pt-1):2001) )	-	0	-
10.4(Linear Deflection Test [ Cl.10.4 ])	-	500	-
10.5(External load Test [ Cl.10.5 ])	-	1000	-
11.1.1(Resistance to flame propagation (As per Cl. 11.1.1))	-	1000	-
11.1.1(Resistance to flame propagation (As per Cl. 11.1.1))	-	1000	-
12.2(Electrical continuity Test for earthing or bonding [ Cl.12.2 ])	-	1000	-
12.2(Electrical continuity Test for earthing or bonding [ Cl.12.2 ])	-	0	-
12.3(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ])	-	0	-
12.3(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ])	-	0	-
12.3(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ])	-	500	-
13(External Influences )	-	500	-
7(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7.101(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7.102(Marking (as per Cl 7.1 of IS:14927(Pt-I ):2001))	-	0	-
7(Marking (as per Cl 7.2 of IS:14927(Pt-I ):2001))	-	0	-
8( Dimensions (As per cl.8.1 of IS 14927(Pt-1) : 2001))	-	500	-
8(Dimensions (As per cl.8.2 of IS 14927(Pt-1) : 2001)	-	500	-
8( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
8( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
8( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
8( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
8( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
8( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	500	-
8( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
8( Dimensions (As per cl.8.3 and Table-2 of IS 14927(Pt-1) : 2001))	-	0	-
9(Construction ( As per Cl. 9.1 of IS 14927(Pt-1):2001))	-	0	-
9.1.101(Construction)	-	500	-
9(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-	500	-
9(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-	0	-
9(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-	500	-
9(Construction ( As per Cl. 9.2 of IS 14927(Pt-1):2001))	-	0	-
9(Construction ( As per Cl. 9.3 of IS 14927(Pt-1):2001))	-	0	-
9(Construction ( As per Cl. 9.3.1 of IS 14927(Pt-1):2001))	-	0	-
9(Construction ( As per Cl. 9.3.2, Table-3 of IS 14927(Pt-1):2001))	-	0	-
9(Construction [Access to Live Parts (As per Cl. 9.4.1 of IS 14927(Pt-1):2001)])	-	0	-
9(Construction (As per Cl. 9.5 of IS 14927(Pt-1):2001))	-	0	-
9(Construction [Membranes (As per Cl.9.6.2 of IS: 14927 (Pt-1):2001)])	-	500	-
9(Construction [Membranes (As per Cl.9.6.4 of IS: 14927 (Pt-1):2001)])	-	0	-
9(Construction [Glands (As per Cl.9.7.2 and Table-4 of IS: 14927 (Pt-1):2001)] )	-	0	-
10(Mechanical Properties )	-	1000	-
10(Cable supporting test for Surface mounting (As per Cl.10.2))	-	500	-
10(Cable supporting test for Surface mounting (As per Cl.10.2))	-	500	-
10(Cable supporting test for Surface mounting (As per Cl.10.2))	-	0	-
10(Cable supporting test for Surface mounting (As per Cl.10.2))	-	0	-
10(Cable supporting test for Surface mounting (As per Cl.10.2))	-	0	-
10(Cable supporting test for Surface mounting (As per Cl.10.2.3))	-	0	-
10(Cable supporting test for Surface mounting (As per Cl.10.2.3))	-	0	-
10(Cable supporting test for Surface mounting (As per Cl.10.2.3))	-	0	-
10(Cable supporting test for Surface mounting (As per Cl.10.2.3))	-	0	-
10(Impact Test [ Cl.10.3 ])	-	1000	-
10(Impact Test (As per Cl. 10.3.4 of IS: 14927(Pt-1):2001) )	-	500	-
10(Linear Deflection Test [ Cl.10.4 ])	-	500	-
10(External load Test [ Cl.10.5 ])	-	500	-
11(Resistance to flame propagation (As per Cl. 11.1.1))	-	500	-
11(Resistance to flame propagation (As per Cl. 11.1.1))	-	500	-
12(Electrical continuity Test for earthing or bonding [ Cl.12.2 ])	-	500	-
12(Electrical continuity Test for earthing or bonding [ Cl.12.2 ])	-	500	-
12(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ])	-	500	-
12(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ])	-	500	-
12(Electrical Insulating Strength and Insulation Resistance Test. [ Cl.12.3 ])	-	500	-
13(External Influences )	-	500	-
4(General Requirements)	-	0	-
5(General Conditions for test)	-	0	-
7(Marking)	-	500	-
8(Dimensions)	-	500	-
9(Construction)	-	500	-
10(Mechanical Properties)	-	500	-
11(Resistance to flame propagation)	-	500	-
12(Electrical characteristics)	-	500	-
13(External Influences)	-	500	-

15 Jun, 2029

-
Included w.e.f 14.08.2025

IS 2993 : Part 2 (2024)

a.c. Motor Capacitors Part 2 Motor Start Capacitors ( Third Revision )

AC MOTOR CAPACITORS PART-2 MOTOR START CAPACITORS

440000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1.1(General)	-	1000	-
5.1.7(Voltage test between the terminals)	-	3000	-
5.1.8(Voltage test between terminals and case)	-	3000	-
5.1.9(Capacitance measurement)	-	4000	-
5.1.10(Check of dimensions)	-	1000	-
5.1.10(Check of dimensions)	-	1000	-
5.1.11.1(Robustness of terminations)	-	2000	-
5.1.11.2(Soldering)	-	1000	-
5.1.11.3(Vibration)	-	14000	-
5.1.12(Sealing test)	-	2000	-
5.1.13(Endurance test)	-	110000	-
5.1.14(Damp heat test)	-	4000	-
5.1.15(Self-healing test)	-	4000	-
5.1.16(Destruction test)	-	65000	-
5.1.17.1(Ball-pressure test)	-	4000	-
5.1.17.2(Glow-wire test)	-	4000	-
5.1.17.3(Tracking test)	-	5000	-
5.2(Overloads)	-	1000	-
5.3.1(Creepage distances and clearances)	-	1000	-
5.3.2(Terminals and connecting cables)	-	1000	-
5.3.3(Earth connections)	-	1000	-
5.3.4(Discharge devices)	-	40000	-
5.3.5(Pollution)	-	2000	-
5.4(Marking)	-	1000	-
6.1.6(Voltage test between the terminals)	-	1000	-
6.1.7(Voltage test between terminals and case)	-	1000	-
6.1.8(Capacitance and power factor measurement)	-	4000	-
6.1.9(Check of dimensions)	-	1000	-
6.1.10.1(Robustness of terminations)	-	1000	-
6.1.10.2(Soldering)	-	1000	-
6.1.10.3(Vibration)	-	15000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	1000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	1000	-
6.1.10.5(Rapid change of temperature)	-	1000	-
6.1.11(Sealing test)	-	1000	-
6.1.12(Endurance test)	-	110000	-
6.1.13(Damp heat test)	-	5000	-
6.1.14(Pressure relief test)	-	1000	-
6.1.15.1(Ball-pressure test)	-	1000	-
6.1.15.2(Glow-wire test)	-	1000	-
6.1.15.3(Tracking test)	-	1000	-
6.2(Overloads)	-	1000	-
6.3.1(Creepage distances and clearances)	-	1000	-
6.3.2(Terminals and connecting cables)	-	1000	-
6.3.3(Earth connections)	-	1000	-
6.3.4(Discharge devices)	-	5000	-
6.3.5(Pollution)	-	2000	-
6.4(Marking)	-	1000	-
7.2.1(Measurement of working voltage)	-	1000	-
7.2.2(Influence of capacitance)	-	1000	-
7.3(Checking capacitor temperature)	-	1000	-
7.4(Checking transients)	-	1000	-
7.5(Storage of electrolytic capacitors)	-	2000	-
Annex A(Test voltage)	-	1000	-
5.1.1.1(General)	-	1000	-
5.1.7(Voltage test between the terminals)	-	3000	-
5.1.8(Voltage test between terminals and case)	-	3000	-
5.1.9(Capacitance measurement)	-	4000	-
5.1.10(Check of dimensions)	-	1000	-
5.1.10(Check of dimensions)	-	1000	-
5.1.11.1(Robustness of terminations)	-	2000	-
5.1.11.2(Soldering)	-	1000	-
5.1.11.3(Vibration)	-	14000	-
5.1.12(Sealing test)	-	2000	-
5.1.13(Endurance test)	-	110000	-
5.1.14(Damp heat test)	-	4000	-
5.1.15(Self-healing test)	-	4000	-
5.1.16(Destruction test)	-	65000	-
5.1.17.1(Ball-pressure test)	-	4000	-
5.1.17.2(Glow-wire test)	-	4000	-
5.1.17.3(Tracking test)	-	5000	-
5.2(Overloads)	-	1000	-
5.3.1(Creepage distances and clearances)	-	1000	-
5.3.2(Terminals and connecting cables)	-	1000	-
5.3.3(Earth connections)	-	1000	-
5.3.4(Discharge devices)	-	40000	-
5.3.5(Pollution)	-	2000	-
5.4(Marking)	-	1000	-
6.1.6(Voltage test between the terminals)	-	1000	-
6.1.7(Voltage test between terminals and case)	-	1000	-
6.1.8(Capacitance and power factor measurement)	-	4000	-
6.1.9(Check of dimensions)	-	1000	-
6.1.10.1(Robustness of terminations)	-	1000	-
6.1.10.2(Soldering)	-	1000	-
6.1.10.3(Vibration)	-	15000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	1000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	1000	-
6.1.10.5(Rapid change of temperature)	-	1000	-
6.1.11(Sealing test)	-	1000	-
6.1.12(Endurance test)	-	110000	-
6.1.13(Damp heat test)	-	5000	-
6.1.14(Pressure relief test)	-	1000	-
6.1.15.1(Ball-pressure test)	-	1000	-
6.1.15.2(Glow-wire test)	-	1000	-
6.1.15.3(Tracking test)	-	1000	-
6.2(Overloads)	-	1000	-
6.3.1(Creepage distances and clearances)	-	1000	-
6.3.2(Terminals and connecting cables)	-	1000	-
6.3.3(Earth connections)	-	1000	-
6.3.4(Discharge devices)	-	5000	-
6.3.5(Pollution)	-	2000	-
6.4(Marking)	-	1000	-
7.2.1(Measurement of working voltage)	-	1000	-
7.2.2(Influence of capacitance)	-	1000	-
7.3(Checking capacitor temperature)	-	1000	-
7.4(Checking transients)	-	1000	-
7.5(Storage of electrolytic capacitors)	-	2000	-
Annex A(Test voltage)	-	1000	-

15 Jun, 2029

-
Included w.e.f 02.09.2025

IS 2993 : Part 1 (2024)

a.c. Motor Capacitors Part 1 General - Performance, Testing and Rating - Safety Requirements - Guidance for Installation and Operation ( Third Revision )

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(General)	-	5000	-
5.5(Tangent of loss angle)	-	10000	-
5.7("Voltage test between terminals ")	-	5000	-
5.8(Voltage test between terminals and case)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.1(Check of dimensions)	-	5000	-
5.11(Mechanical tests)	-	20000	-
5.12(Sealing test)	-	10000	-
5.13(Endurance test)	-	110000	-
5.14(Damp heat test)	-	60000	-
5.15(Self-healing test)	-	10000	-
5.16(Destruction test)	-	40000	-
5.17(Resistance to heat, fire and tracking)	-	20000	-
5.17.1(Ball-pressure test)	-	5000	-
5.17.2(Glow-wire test)	-	5000	-
5.17.3(Tracking test)	-	5000	-
6.1(Maximum permissible voltage)	-	5000	-
6.2("Maximum permissible current ")	-	5000	-
6.3(Maximum permissible reactive output)	-	10000	-
7(Safety requirements)	-	10000	-
7.1(Requirements for Creepage distances and clearances)	-	5000	-
7.2(Terminals and connecting cables)	-	5000	-
7.3(Earth connections)	-	5000	-
7.4(Discharge devices)	-	40000	-
8(Marking)	-	5000	-
9.2.1(Measurements of working voltage)	-	5000	-
9.2.2(Influence of capacitance)	-	5000	-
9.3(Checking capacitor temperature)	-	5000	-
9.4(Checking transients)	-	10000	-
9.5(Leakage current)	-	10000	-
5.1.1(General)	-	5000	-
5.5(Tangent of loss angle)	-	10000	-
5.7("Voltage test between terminals ")	-	5000	-
5.8(Voltage test between terminals and case)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.1(Check of dimensions)	-	5000	-
5.11(Mechanical tests)	-	20000	-
5.12(Sealing test)	-	10000	-
5.13(Endurance test)	-	110000	-
5.14(Damp heat test)	-	60000	-
5.15(Self-healing test)	-	10000	-
5.16(Destruction test)	-	40000	-
5.17(Resistance to heat, fire and tracking)	-	20000	-
5.17.1(Ball-pressure test)	-	5000	-
5.17.2(Glow-wire test)	-	5000	-
5.17.3(Tracking test)	-	5000	-
6.1(Maximum permissible voltage)	-	5000	-
6.2("Maximum permissible current ")	-	5000	-
6.3(Maximum permissible reactive output)	-	10000	-
7(Safety requirements)	-	10000	-
7.1(Requirements for Creepage distances and clearances)	-	5000	-
7.2(Terminals and connecting cables)	-	5000	-
7.3(Earth connections)	-	5000	-
7.4(Discharge devices)	-	40000	-
8(Marking)	-	5000	-
9.2.1(Measurements of working voltage)	-	5000	-
9.2.2(Influence of capacitance)	-	5000	-
9.3(Checking capacitor temperature)	-	5000	-
9.4(Checking transients)	-	10000	-
9.5(Leakage current)	-	10000	-

15 Jun, 2029

-
-

IS 1258 (2024)

Bayonet lampholders (Fifth Revision)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General requirements)	-	1000	-
6(Standard ratings)	-	1000	-
7(Classification)	-	500	-
8(Marking)	-	500	-
9(Dimensions)	-	1000	-
10(Protection against electric shock)	-	1000	-
11(Terminals)	-	1000	-
12(Provision for earthing)	-	1000	-
13(Construction)	-	1000	-
14(Switched lampholders)	-	1000	-
15(Moisture resistance, insulation resistance and electrical strength)	-	1000	-
16(Mechanical strength)	-	1000	-
17(Screws, current-carrying parts and connections)	-	1000	-
18(Creepage distances and clearances)	-	1000	-
19(General resistance to heat)	-	1000	-
20(Resistance to heat, fire and tracking)	-	1000	-
21(Resistance to excessive residual stresses (season cracking) and to rusting)	-	1000	-
Annex A(Season cracking/corrosion test)	-	500	-
12.4(Thermal tests)	-	500	-
9.1(Lampholder dimensions)	-	500	-
11.2(Terminals)	-	500	-
12.3(Provision for earthing)	-	500	-
13.1(Construction)	-	500	-
13.8(Construction)	-	1000	-
14.4(Switched lampholders)	-	500	-
15.1(Moisture resistance, insulation resistance and electrical strength)	-	500	-
16.7(Mechanical strength)	-	300	-
16.8(Mechanical strength)	-	200	-
21.2(Resistance to excessive residual stresses (season cracking) and to rusting)	-	500	-

15 Jun, 2029

-
Included w.e.f 04.07.2025

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

ATCC TEST LABS LLP

KHASRA NO. 45/6, SITUATED IN THE AREA, VILLAGE PRAHLADPUR BANGER,, North West Delhi, Delhi, 110042, Delhi, North West, Delhi, 110042

9891606632 info@atcctestlabs.com

Scope List